CATHODE RAY TOMES

Battlezone Caberat TM-166 2nd Printing

Battlezone (rev 2) (Atari, 1980) · Technical Manual · 64 pages · 48 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

GAME SERIAL NUMBER LOCATION e

Your game's serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the TV monitor, Regulator/Audio Il PCB, Battlezone Analog Vector-Generator PCB, and Battlezone Auxiliary PCB. Please mention this number whenever calling your distributor for service.

GAME SERIAL # IDENTIFICATION TAG

TV MONITOR

BATTLEZONE

AUXILIARY PCB

REGULATOR/AUDIO Il PCB.

BATTLEZONE ANALOG VECTOR-GENERATOR PCB

Page 3

a CABARET”

Operation, Maintenance

and Service Manual

Complete with lilustrated Parts Lists

Published by: ATARI INC. 1265 Borregas Avenue P. 0. Box 427 Sunnyvale, California 94086

Copyright © 1980 by Atari, Inc. All rights reserved.

No part cf this publication may be reproduced by any mechanical, photographic. or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system. transmitted, or otherwise copied for public or private use, without permission itom the publisher:

Lithographed in the U.S.A. Wd ™

A.

ATARI

Page 4

Table of Contents

Location Setup A. B. c. Game Inspection 3 Game Installation . 3

  • Line Voltage Selection . .. 3
  • Interlock and Power On/Off witches . 4 Self-Test Procedure ............... _7 Option Switch Settings
  • Bonus Play Feature.
  • Coin Mechanism Multipliers . .
  • Examples of Option Switch Settings . : GamePlay ...............-0.055 . 12
  • Attract Mode .
  • Ready-to-Piay Mode 12
  • PlayMode .......... . . 13
  • High Score Initial Mode 2.0.0.0... 0... cece cee cere 13

Maintenance and Repair A. Cleaning..... - 16 B. Fuse Replacement... . 16 C. Opening the Control Panel . . - 16

  • LED Stari Switch Replacement . - 16
  • Control Handle Maintenance and Repair . . 18 D. TV MonitorRemoval ............-.66 » 19 E. Printed-Circuit Board Replacement . . 20
  • Analog Vector-Generator and Auxiliary PCB Removal . - 20
  • Regulator/Audio Il PCE Removal . . 20 Ff. Fluorescent Tube Replacement . ‘ 224 G. Game Operation... 2.6.0.6... c ec eceee eee e eee 22

Illustrated Parts Lists

Page 5

List of Dlustrations

Figure 1 Overview of Game .. 2.2.6 eee eee eee 2 Figure 2 Installation Requirements . 3 Figure 3 Line Voltage Selection . | 4 Figure 4 Interlock and Power Onioft Switches . 5

Figure 5 Location of Self-Test Switch, Volume Controi and Option Switches... 6 Figure 6 Self-Test Procedure ..... 0.00... c cece cece ect eee e ee ceee 7 Figure 7 Game Option Settings .. 9 Figure 8 Game Price Settings. ... 10

Figure 9 Coin Counter Option Settings . . . 12 Figure 10 Opening the Control Panel 16 Figure 11. Control Handle Maintenance and Repair 7 Figure 12 TV Monitor Removal . - 19

Figure 13 Printed-Circuit Board Replacement Figure 14 Fluorescent Tube Replacement Figure 15 Power Distribution .. . Figure 16 = Signal Distribution .. .

lijustrated Parts Lists: Figure 17 | Cabinet-Mounted Assemblies . . Figure 18 Control Panel Assembly Figure 19 Control Handle Assembly . . Figure 20 Fluorescent Light

Figure 21. Power Supply Assembly for X-Y Games . Figure 22 Battlezone™ Auxiliary PCB ........... Figure 23 Battlezone™ Analog Vector-Generator PCB Figure 24 —Regulator/Audio Il PCB Assembly . Figure 25 Coin Door

Page 6
NOTE

If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographical area, as shown in one of the two maps below. Order all parts from the California office.

WEST and CENTRAL U.S.A.

Parts for all Atari Customers. Sales and Service

Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103

(Monday - Friday, 7:30 - 4:00 pm Pacific Time) zs From California, Alaska or Hawaii (408) 745-2900

@e= From anywhere else in this area toll-free (800) 538-1611

EAST U.S.A.

Sales and Service Only

Atari Inc. New Jersey Customer Service Office Cottoniail Lane, Somerset, NJ 08873 Telex 37-9347

(Monday - Friday, 7:30 - 4:00 pm Eastern time)

s From New Jersey (201) 469-5993

«=~ From anywhere else in this area toll-free (800) 526-3849

Page 7

Notice Regarding Non-Atari Parts

WARNING

Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:

1.) you substitute non-Atari parts in your coin-operated game, or 2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.

Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 8

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 9
WARNING-SHOCK HAZARD This game is designed to be connected only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

A. New Parts

The Battlezone™/Cabaret game has four new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: @ Control Handle. This new control is a redesign of the Atari gear shifter. It has been strengthened by adding several additional ribs to the interior and exterior of the housing. These ribs keep the assembly properly aligned to assure proper switch contact. Another new feature is the rubber centering bellows; it acis as a centering spring to return the control handle to the center position. The microswitches are now mounted with locknuts for easy replacement.

Page 10

Battlezone “Cabaret

TV MONITOR SHIELD

CONTROL HANDLE

START SWITCH

CONTROL (ll

PANEL, =

ATTRACTION PANEL

AUXILIARY PCB

ANALOG VECTOR. GENERATOR PCB

COIN DOOR REGULATOR/ AUDIO I! PCB

SPEAKER

POWER SUPPLY

POWER ON/OFF SWITCH

Figure 1 Overview of Game XY TV MONITOR

ACCESS. PANEL

Page 11

@ = Atari’s X-Y game circuitry has expanded into two interconnected printed-circuit boards—the Analog Vector-Generator and the Auxiliary PCBs. The circuitry produces more lines on the screen at a faster rate, thus creating a smoother screen image. @ This game includes a newly designed power supply assembly. This power supply has a larger transformer to handle the increased power requirements of the expanded game circuitry. @ Cabaret™ Cabinet Design.This more compact cabinet was designed to occupy less than 4 square feet of floor space.

These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is

mentioned, you will see this symbol: S

B. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.

NOTE Do not piug the game in yet!
  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON’T FORCE CONNECTORS TOGETHER. The

a” Ow D connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.

WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the TV monitor with your hands or metal objects held in your hands!

@ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the seria! numbers also stamped on the Battlezone™ Analog Vector-Generator PCB, Auxiliary PCB, Regulator/Audio II PCB and TV Monitor are all identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and TV monitor for secure mounting.

C. Game Installation

Figure 2 Installation Requirements

Power 150 watts Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 52 x 6024 cm (20% x 23 7/8 in.) Game Height 139 cm (54% in.)

  • Line Voltage Selection The international power supply has 4 colored plugs. Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per the list below.

Line Voltage Range Voltage Selection Plug Color 90-110 VAG (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (220) Blue 220-280 VAC (240) Brown ~S

Page 12

Figure 3 International Line Voltage Selection

  • Interlock and Power OnlOff Switches @ ifthe results of the preceding step are satisfacsoe . ; tory, the interlock switches are operating pro- To minimize the hazard of electrical shock while perly. If the TV monitor doesn't go off as working on the inside of the game cabinet, two inter- described, check to see if the corresponding inlock switches have been installed (see Figure 4). terlock switch is broken from its mounting or One is located behind the access panel and one is stuck in the “on” position. behind the coin door. These switches remove all AC line power from the game circuitry when a door is opened.

Check for proper operation of the interlock switches by performing the following steps: @ Unlock and open the access panel and the coin door. @ Plug the AC line power cord into an AC outlet. Close the access panel and coin door. @ Set the power on/off switch to the on position. Within 30 seconds the TV monitor should display a picture. @ Slowly open the access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock the access panel and repeat this step with the coin door.

Page 13

Battlezone Cabaret

SWITCH COVER

SAFETY INTERLOCK SWITCH ¢

POWER ON/OFF SWITCH

Figure 4 Interlock and Power On/Off Switches

Page 14

D. Self-Test Procedure

Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test pro- This game will test itself and provide data to cedure anytime you need to change ihe game’s demonstrate that the game’s circuitry and con- options. trols are operating properly. The data is provided on the TV monitor and the game speaker; no addi- To run the self-test, follow the instructions outtional equipment is necessary. lined in Figure 6.

Figure 6 Self-Test Procedure

Results if Test Fails Results if

Instruction Test Passes

  • Set self-test After about 3 switch to on posi- seconds, the TV tion (see Figure 5). monitor displays the picture betow.

CENTER COIN MECH MULTIPLIER (LEFT MECH OF A 2-MECH DOOR)

RIGHT COIN MECH MULTIPLIER

SWITCH SWITCH

TOGGLE 1 TOGGLE 8

\x

in

ax

AT P10 AT M10 {TOP ONE) (BOTTOM ONE)

DISPLAY OF COMPLETE CHARACTER SET RAM FAILURE is indicated by a sequence of 1 to 10 tones. You will hear a short low tone for each good RAM chip, and a long high tone for a failing RAM chip. The test stops with the first failing RAM-chip pair (exampie: J2 and H2 are a pair). To restart the sequence, press the reset pushbutton on the Battlezone™ Analog Vector-Generator PCB, or sei the self-test switch to off, then again to the on position. Identify the bad RAM chip with the table below. Example: four short low tones followed by a long high tone, then one more short low tone indicates failure of RAM at location B2. Long High Tone Bad RAM Chip Location Ist J2 2nd H2

3rd A2 4th Al

sth B2 6th BI

7th c2 8th cl

9th b2 40th O1

ROMIPROM FAILURE is indicated by two columns of numbers on the leit side of the screen. The number in the left column indicates the location of the failing ROM/PROM(s). identity the bad ROM/PROM with the table immediately below.

ignore the hexadecimal numbers in the right column.

Displayed No. Failing ROM Failing PROM BIC3* BIC3*, E3 a3 A3, FIH3 e1 FHT a Ki uM1 Niw* *If ROM or PROM BIC3 is bad, you will hear a continuous low tone, and the program may be unable to display a screen image. NOURwWNAO

**If ROMN1 is bad, program will be unable to produce tones in RAM test.

[Selt-test continued on next page]

Page 15

VOLUME INCREASE: TURN CLOCKWISE

SELF-TEST SWITCH (EUROPEAN GAMES) VOLUME CONTROL

Figure 5 Location of Self-Test Switch,

Volume Conirol and Option Switches

“~S BATTLEZONE ANALOG VECTOR-GENERATOR PCB

OPERATOR OPTION SWITCH

Page 16

The right coin mechs are all the same to the game’s logic, regardless of whether you have two or three mechs in your door. In addition, the logic sees the left mech in a 2-mech door and the center mech in a 3-mech door as the same. Refer to the diagram below.

(50 \s1 [ese | [esd [s1|

This pattern is important for you to know, so you can correctly set the “multipliers” for each mech. The multipliers determine how much each mechanism will be worth to the game’s logic. The basic unit of measurement is 25¢, which equals a multiplier of x 1. Therefore, if you have a 25¢/25¢/$1 coin door, you will probably want to set the center and right option-switch multipliers at x tix 4. (The left mech in a 3-mech door always has a value of x 1—you cannot change its value.)

You can set these multipliers with toggles 3 thru5 on the Battlezone PCB switch assembly at location P10. For exact settings of these toggles, refer to Figure 8.

  • Examples of Option Switch

Settings

To explain the options, we have provided in Figure 8 fourteen examples of the most common U.S. situations. The toggles mentioned are all in the switch at location P10; they only relate to game price, coin mechanism multipliers, and bonus play. You should set the toggles relating to other functions as you see fit, although Figure 7 provides “$” symbols indicating Atari’s recommendations.

Figure 7 Game Option Settings S \ ro change togale positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the Battlezone Analog Vector-Generator PCB is mounted in place. When changing the options, verify proper results on the TV monitor display by performing the self-test. Note that changing an option on any of the following eight toggles will cause an immediate change on the TV monitor screen during the self-test.

Toggle Settings of -Toggle Switch on Battlezone PCB (at M10) {BOTTOM switch when PCB is in game) 8 7 6 5 4 3 2 Option

On

Off Off

On On On Off

Off On

Off Off

on Off

On Off

On Game starts with 2 tanks oft Game starts with 3 tanks $ On Game starts with 4 tanks Off Game starts with 5 tanks Missile appears after 5,000 points Missile appears after 10,000 points $ Missile appears after 20,000 points Missile appears after 30,000 points No bonus tank Bonus tank at 15,000 and 100,000 points $ Bonus tank at 25,000 and 100,000 points Bonus tank at 50,000 and 100,000 points English language $ French language German language Spanish language

Page 17

Figure 6

Results if

Instruction Tesi Passes

Self-Test Procedure, continued

Resutts if Test Fails

As switch activates, you'll hear a low beep. panel switches and As switch deactivates, coin door switches. you'll hear a high When satisfied with Deep. test, set self-test switch to off position.

  • Activate slam switch, all control
  • Sounds Test (Optional) You may test the hardware-generated sounds by starting a game and proceeding as follows: Engine Rumble (Idle): Shouid be heard as soon as start button is pushed. Engine Rumble (Active): Pushing both control handles forward should cause an increase in pitch. Releasing control handles MATH BOX FAILURE is indicated by a single letter displayed in the upper right corner of the display. Math-box failure is explained in the Signature Analysis Procedure, on the game schematic Sheet 1, Side B. Identify the failure with the table below.

Displayed Letter Failure T Time out error H Data error—high byte L Data error—low byte

You will not hear a low or high beep for the defective switch.

should cause engine rumble to return to idle. Loud Shot: Press the fire button.

Loud Explosion: Heard when you get hit, indicated by cracked windshield.

Soft Explosion: Is heard when you hit an enemy tank or another object.

E. Option Switch Settings

  • Bonus Play Feature Battlezone™/Cabaret offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.

For example, with your game set at 50¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, can receive a bonus play. Therefore, players can receive 3 plays for $1.00. This bonus feature encourages players to insert more money than just the minimum 50¢ required for one game. Various other bonuses are also available (see Figure 8).

  • Coin Mechanism Multipliers Since early in 1980, Atari has made available its new coin door which has either two or three mechanisms. All recent Atari game PCBs identify the different mechanisms in a certain pattern.
Page 18

Battlezone MiCabaret

Figure 8 Game Price Settings S

The white block below contains the manufac- P10, on the Battlezone™ Analog Vector-Generator turer's suggested settings. All numbers 1 thru 8 are PCB (the TOP switch assembly). toggle settings on the 8-toggle switch at location

50¢ PER PLAY:

$50 Bonus 8.75

No bonus$1.00 = 3 plays$1.00 = 3 plays
67658765876§
StraightOn On On OnOn Off Of OnOn On Off On

25¢ Door

10) 4321fC) 4321iS) 4321
On On off offOn On of offOn On Of Off
876587 6§8765
257/81.00On on On On{@)on of off On|@on on of On

Door or (0) ©

25¢/25¢/$1.0043214321© 4321

Door On Of off off On Off Of Off On Off Of OM

25¢ PER PLAY:

Bonus Bonus

No bonus$.50 = 3 plays$1.00 = 5 plays
@768@o765 |8765

Straight On On On On On On Off ‘On On Off On On

2¢ Door

@ 4321@ 4a21@ 432.71
On On Off OnOn On Off. On|On On. Off On
e776587658765
25¢/$1.00On On On OnOn On Off. OnOn Off ..On-. On

Door or

asepoisico Da324®,30204® 4.3245
DoorOn Of Off OnOn Off Off OnOn Of Off On

Circled numbers refer to coin-door labels you should use with each situation (labels are illustrated on opposite page).

Page 19

Battlezone MCabaret

Figure 8 Game Price Settings, continued For your information, we have defined below the switch set- _need to temporarily set the Battlezone™ game on free play, or it tings for those options relating to game price, coin mechanism you have German coin mechanisms in your door. multipliers, and bonus play. This information is useful in case you

Toggle Settings of 8-Toggle Switch on Battlezone PCB (at P10). TOP switch when PCB is in game

8754321Option
7oOOnOnFree play7
onOff1 coin” for 2 plays
olfOn1coin* for 1 play
otfot2 coins” fort play$
OnOnRight coin mech x 1$
OnorfRight coin mech x 4
OltOnRight coin mech x 5
offoffRight coin mech x 6

On. Center coin mech x 1 $ (Both these settings affect ott Center coin mech x 2 the left mech in a 2mech door)

OnOnOnNo bonus coins
OnOnoffFor every 2 coins” inserted, game logic adds 1 more

coin*

OnOffOnFor every 4 coins” inserted, game logic adds 1 more

coin*

OnOffOffFor every 4 coins” inserted, game logic adds 2 more

coins* $

OffOnOnFor every 5 coins” inserted, game logic adds 1 more

coin*

*in the US., a “coin” is defined as 258. In Germany a “coin” is ?

ane@@ 2coins =
$ Manufacturer's suggested settingsU8@@@ 3 coins

To achieve bonus plays, all coins must be inserted before pushing @Q@@ 4coins start button.

]©@@ 2coins=1 play
2@® 2 coins =1 playAs@ 1coin =3 plays

(Susan B. Anthony coin)

@ 1 coin = 1 play mag! 2 play minimum (2 coins = 2 plays) e J. @ icoin = 1 play ATARI

Note: Battlezone cannot be set for a 2-coin e . minimum. Theretore, do not stick the above Xx e @ 2 coins = 1 play label no. 6 on the Battlezone coin door. ATARI 6 @ @ @ 4 coins = 3 plays

J (Write in the

appropriate phrase)

Page 20

Figure 9 Coin Counter Option Settings

[These toggles determine which coin mechanisms activate which counters]

Toggle Settings of 4-Toggle Switch on Game PCB (at L11) 4 3 2 1 For Games Having These Coin Doors: Option

OnonThai 1 Baht/1 Baht, German 1 DM/1 DM, U.S. 25¢/-All 3 coin mechanisms are

25¢, Belgian or French 5 Fr/5 Fr, Swiss or French same denomination; all 1 Frit Fr, U.S. 25¢/25¢/25¢, Japanese Y100/Y 100, register on one coin Swedish 1 Kr/1 Kr, U.K. 10 P/10 P, Australian 20¢/- counter. 20¢, or Italian 100 L/100 L.

OffOnGerman 2 DM/1 DM, German 1 DM/5 DM, U.S. 25¢/-Left and center mechanisms

25¢/$1, or U.S. 250/31, are same denomination; right mech is another denomination. Requires two coin counters.

OnOffNo coin door is currently designed for this config-Left mech is one denomina-

uration. tion; center and right mech are another denomination. Requires two coin counters.

OffOffGerman 1 DM/2 DM/5 DM.Left, center and right mechs

are 3 different denominations. Requires three coin counters.

F. Game Play

Atari’s Battlezone™ is a one-player game with an X-Y or vector-generation monitor. The game depicts a first-person view from inside a tank. The battles are fought in a large valley that is completely surrounded by mountains and volcanos. The valley floor contains pyramids and boxes that can provide iemporary protection for players. (These cannot be destroyed by shots.)

The enemy consists of slow and fast “super” tanks and intelligent missiles—all of which become more evasive as the game progresses. In addition, flying saucers appear periodically. These don’t shoot at players, but players can get very high point scores for shooting them.

The Battlezone game has five possibile modes of operation: Attract, Ready-to-Play, Play, High Score Initial, and Self-Test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled and the high score initials are reset.

  • Attract Mode The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when in self-test.

In this mode, the TV monitor displays three possible pictures. One is a simulation of a typical game, another is the high score table, and the third picture shows the Battlezone logo rolling up from the bottom of the screen.

  • Ready-to-Play Mode This mode begins when sufficient coins have been accepted for a game. It ends when the start pushbutton is pressed. When this mode begins, the message PUSH START flashes in the center of the
Page 21

screen, and the start button will also flash on and off. The sequence of displayed pictures are otherwise the same as those shown in the attract mode.

  • Play Mode The play mode begins when the start pushbutton is pressed. The start LED will then stay on, and the audio will begin. The mode ends when the player's last tank of the game is lost.

The game starts with the slow tank visible on the screen. The player can determine the position of either type of tank or the missile by reading the messages in the upper left corner of the screen. For example, ENEMY TO RIGHT may be displayed. In addition, the sweeping radar display shows a dot for the enemy’s location, accompanied by a sonar “blip” sound.

The upper pie-shaped area on the radar represents the player's range of view on the screen below. If the enemy falls anywhere within the radar circle, it will be accompanied by the message ENEMY IN RANGE.

Occasionally the flying saucer appears on the screen. It is a observer to the battle and will not destroy the enemy or player. Its position is never shown on the radar, but players can earn 5,000 points for shooting it down. The saucer does act as a distraction, though, since it usually appears at the same time as the enemy tanks or missile. Saucers can be shot by the piayer as well as enemy tanks. Battlezone Cabaret

Scoring for hitting the enemy is as follows: the slow tank earns a player 1,000 points; the missile earns 2,000 points; and the super tank earns 3,000 points. A super tank moves and turns twice as fast as both the slow tank and the player's tank.

Several options allow operators to set the Battlezone™ game for 2 through 5 tanks, for giving a bonus tank after earning various point scores, and for adjusting difficulty by having the missile appear for the first time at various point scores. For information on how to set your game for these options, refer to Figure 7 in this manual

  • High Score Initial Mode If a player’s score exceeds the minimum on the high score initial list, he or she may put up to three initials on this list at the end of the game. The instructions are self-explanatory and are provided in four languages.
Note that this list is erased whenever you enter the self-test, press the RESET button on the Battlezone™ Analog Vector-Generator PCB, or turn off the power. This resetting will put a list of ten “highest” scores and initials on the screen (to provide player challenge).

Any score on the list over 100,000 points is specially highlighted with a tank symbol following the player's initials. If a player doesn’t enter his or her initials within about 60 seconds, the game will automatically enter dashes instead. After this, the game reverts to the attract mode. S

Page 22

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 23

= Maintenance and Repair

All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if the control handle switches, fire button, or start switch is broken, or if the LED has burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly lubricate the control handle: for details see this chapter.

Page 24

A. Cleaning

The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. \f desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result in fogging the plastic.

B. Fuse Replacement

This game contains five fuses—all on the power supply assembly (not including the TV monitor fuses). Note that the F2 holder is unused. Replace fuses only with the same type as listed in Figure 21 of this manual. See the Quadrascan TV monitor manual, TM-151, for the monitor fuse data.

C. Opening the Control Panel

Prior to repairing or replacing any switch on the control panel, unplug the game. Then open the coin door.

Reach through the opening and remove ail three sets of carriage bolts, hex nuts, split lock washers, and flat washers, located on the underside of the control panel (see Figure 10). Lift up on the control panel and tilt it towards you.

  • LED Start Switch Replacement The light-emitting diode (LED) switch on the control panel has a very low failure rate. In case the switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 10.

To remove LED switch: © Remove all wires from the faulty switch. @ Tur the switch counterclockwise (as viewed from inside of control panel) while holding the black cone-shaped nut on the outside of the control panel. Install a new switch using the reverse procedure. © Reconnect the hamess wires.

NORMALLY CLOSED (N.C.) CONTACT

NORMALLY OPEN (N.O.) CONTACT

» LIGHT-EMITTING-DIODE common —/ (L.ED) CONTACTS | CONTACT

Figure 10 Opening the Control Panel

Page 25

NOTE: 1

Bo not remove the flat actuator spring uniess you have a replacement. Removing the spring will bend it, and it will no longer be usable.

SWITCH ACTUATOR

SWITCH

  • PIN LUBRICATE HERE

Figure 11 Control Handie Maintenance and Repair

Page 26

@ Remove the wires from the suspected switch. @ Sei multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 10 for designation of switch contacts and meter lead placement). ®@ Check contacts (push and release the switch button) for closed and open continuity. @ {fthe contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.

  • Control Handle Maintenance and Repair Normal maintenance involves lubricating three parts in the control handle approximately every six months (this requires removing the controls). First open the control panel as described in Figure 10. Then unplug the “quick-disconnect” connectors on the four control switches, as well as the three connectors for the fire switch.

From the inside of the contro! panel, remove the four flat and lock washers and four screws that mount the control onto the wood support and the round bezel.

Then open up the control handle assembly by removing the six split lock washers and screws (see Figure 11). In addition, remove the two switches and caretully save the small actuator pins.

For lubrication, use only Dow Corning #111 heavy silicone lubricant (Atari part no. 78-1710). Lubricate the following two parts inside the control: @ The spherical part of the shaft and the two small pivot pins that protrude from this area, and @ The two clear plastic actuator pins, located over the switches (push the narrow ends of the pins into the tube to cover them with lubricant}.

NOTE Do not remove this spring unless you have a replacement on hand! Removing the spring will bend it, and it will no longer be usable.

BLACK BLACK GREEN

YELLOW YELLOW

BLACK BLACK / YELLOW

ORANGE WHITE GREEN

Repairs on the control handle would probably only involve replacement of switches. When removing a switch, be careful not to lose the small clear plastic actuator pins that sit above the white switch actuators. Note: the flat head of the pin must always face towards the switch actuator.

Page 27

D. TV Monitor

. Removal

WARNING High voltages may exist in any television monitor, even with power disconnected. Use extreme caution and do not touch electrical parts of the TV yoke area with your hands or with metal objects in your hands! If you drop the TV monitor and it breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any TV monitor.

If you should need to remove the Quadrascan X-Y TV monitor, follow steps 1 thru 6 as listed on this page. Refer to Figure 12. First be sure the game is unplugged from its wali outlet!

1, Uniock and open the rear access panel. Remove the three Allen screws and internal-tooth lock

Disassemble in the order indicated. (Circled numbers match the steps above.) washers that secure the monitor-shield retainer strip at the top of the game. Carefully remove the cardboard graphics bezel by prying loose the staples. Unplug the 12-pin harness connector behind the TV monitor. Remove the four sets of carriage bolts, flat and split lock washers, and hex nuts that hold down the TV chassis. Caretully slide the TV monitor chassis out the front of the game. If you must replace the TV monitor with a new one, place the red and green overlays on the face of the new picture tube as follows. Place ihe red overlay within the top 2% inches of the screen; then butt up the green overlay to the red one. Once the monitor has been installed in the cabinet, check for proper alignment with the graphics bezel as follows—before stapling it into place. The vertical center line of the gunsight should be directly under the D in RADAR (at the top center of the bezel). In addition, the radar circle should be centered in the die-cut circle of the cardboard.

Figure 12 TV Monitor Removal

Page 28

E. Printed-Circuit Board out of the plastic PCB retainer

@ Remove the PCB from the cabinet by pulling it Board out of the plastic PCB retainer. @ Reinstall the PCB, making sure that the 44-pin

Replacement edge connector is properly plugged in. Note

that the connector is keyed to fit on only one way, So if it doesn’t slip on easily, don't force it! You may wish to remove the Battlezone™ Analog A reversed connector will probably damage Vector-Generator printed-circuit board (PCB), Aux- your game and will void the warranty. iliary PCB, or the Regulator/Audio I PCB for service © Check that the operation of the game is correct Coad oe eto To do this, refer to Figure 13 and pro- by performing the self-test. This is especially as sollows: important with any game when you replace a PCB.

  • Analog Vector-Generator and Auxiliary PCB Removal 2. Regulator/Audio || PCB Removal @ Unlock and open the access panel. @ Unlock and open the access panel. Unplug the 24-pin PCB interconnector from the @ Remove the five plug-in connectors on the Reg- Auxiliary PCB or the Analog Vector-Generator ulator/Audio I! PCB. Note thai all of these con- PCB (whichever board you are removing). nectors are keyed for proper orientation. @ Remove the 44-pin edge connector from the @ Locate the iwo Phillips-head screws that exright side of the PCB. tend through the PCB and into the wood behind @ Locate the Phillips-head screw that extends the PCB. ei jand save these’two.screws through the PCB and into the wood block (at and the four fiber washers. the right side of the board). Remove this screw, @ Remove the PCB from the interior wall of the as well as the two fiber washers. cabinet.

BATTLEZONE AS a AUXILIARY PCB REGULATOR!

AUDIO li PCB BATTLEZONE “DS

ANALOG VECTOR. GENERATOR PCB

Figure 13 Printed-Circuit Board Replacement

Page 29

F. Fluorescent Tube Replacement

WARNING lf you drop a fluorescent tube and it breaks, ii will implode! Shattered giass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube. To replace the white fluorescent tube behind the front graphics attraction panel, follow this procedure (see Figure 14).
  • Open the coin door. Remove the two Y-shaped connectors from the ends of the fluorescent tube. Now carefully remove the tube from its clamps by pulling it towards you.
  • Replace with a new tube. Do not snap the tube in vigorously— you may break it, causing an implosion!
  • Close the coin door and lock it.

Figure 14 Fluorescent Tube Replacement

Page 30

G. Game Operation

With this manual you received three large sheets that contain the wiring and schematic diagrams for your game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams.

Baitlezone™ is a microprocessor-controlled game. The microprocessor is contained on the Analog Vector-Generator PCB. This board receives switch inputs from the control panel and coin door. These inputs are then processed by the Analog Vector-Generator PCB and output to the TV monitor, Regulator/Audio || PCB, and controi panel.

The TV monitor is an X-Y monitor. Therefore, the monitor receives signals for the X, Y and Z axes. Since the location of the beam in the monitor is totally controlled by the X- and Y-axis outputs of the Analog Vector-Generator PCB, this board does not contain a standard sync circuit. The X- and Y-axis inputs to ihe monitor step in increments of 1024 steps for the X (horizontal) axis, and 768 steps for the Y (vertical) axis. The Z axis merely controls the intensity of the beam. aS The Regulator/Audio Il PCB performs two functions:. 1) it regulates the voltages from the power supply to +5 VDC and + 12 VDC, and 2) it amplifies the audio output from the Auxiliary PCB.

Specifically, the +5 VDC from the Regulator/- Audio {| PCB provides most logic power to the Analog Vector-Generator and Auxiliary PCB; +22 VDC is regulated on the Analog Vector-Generator PCB to produce + 15 and +5 VDC {the latter for the digital-to-analog converters), and + 22 VDC provides power for the audio output of the Auxiliary PCB. The audio output from the Regulator/Audio Il PCB directly drives the game speakers and is controlled by the volume control, mounted inside the coin door.

The Power Supply is the source of all voltages in the game. These voltages are protected by four fuses in the fuse biock on the power supply chassis. The primary winding of the power supply transformer is protected by the cartridge-type fuse in the power supply chassis.

Figure 15 illustrates the distribution of power in this game. Figure 16 illustrates the distribution of signals.

Page 31

TV MONITOR

CONTROL PANEL

FLUORESCENT LAMP

AUXILIARY PCB

POWER INTERLOCK SWITCHES

ANALOG VECTOR- GENERATOR PCB

COIN DOOR

REGULATORI/AUDIO ii PCB

4 AC POWER CORD

POWER SUPPLY

ON/OFF SWITCH

Figure 15 Power Distribution

Page 32

TV MONITOR

CONTROL PANEL

ANALOG VECTOR. GENERATOR PCB

VOLUME CONTROL.

COIN DOOR

AUXILIARY PCB X.¥.Z OUTPUT

Auplo our

L.C.R. COIN COUNT

GAME SPEAKER

REGULATORIAUDIO II PCB

Figure 16 Signal Distribution

Page 33

[llustrated

Parts Lists

The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your Battlezone™/Cabaret game. Please

note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc. ©

The parts lists have been arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Battlezone “Cabaret

Page 34

Battlezone Cabaret

Schematics, Seli-Test Label & Manuals— see Parts list on opposite page

036669-01 (Monitor Shield) 036263-03, -04 036670.01 (Monitor Overlays) (Shield Retainer) 036676-01 (Graptics Bezel) 92-045, (&Y Monitor) Control Handle Assy.—- See Figure 19 Auxiliary PCB— See Figure 22

Control Panel Assy.— See Figure 1 p 002728-01 ‘gue 16 (Ci-Panel Brkt.)

03574502 (184 PCB Retainer) 03574503 (10-n. PCB Retainer)

036674-01 , (Attract. Panel) é Fluorescent Light— . See Figure 20

A036247-01 (PCB Interconnector) Coin Door— 19-9032 See Figure 25 «Vol. Controt) 034536-02 {Thin Foam Damper) i 036262.01 (Coin Box Brkt) | 00788202 E A021700-01, -02, 03 (inter Sw. Cover} poet ig Analog Vect.-Gener. PCB— Reg/Audio li PCB— See Figure 24

(Coin Box) See Figure 23 03024901 A036 189-01 :

(Separator)(inter! Sw):034536-03

(Thick Foam Damper) 148001-001 (Speaker) 036130-01 speaker Gaile} 4 Power Supply Assy.— See Figure 21 76-3201 Va (Cabinet Leg) A036603-01 (Main Harness)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING Ln CONFIDENTIAL Reproduction forbidden without the {OniOft Sw. Cover) specilic written permission of Atari, Inc.. Sunayvale, CA This drawing 15 only conditionally issued. and neither

receipt nor Bossession Hrecol conters or wansters anyA034631-01A034841.02,

fightin or icenge to use. the subject matter of the craw CniOt .

ing of any design or technical information shown theieen,(OniOls Sw.)403486302,

net any ight fo eoroduce sara. Anya A035989-02 therea? Except for manutacture vy vencorso Atal Ine 1355 ind for manulacture under the’ corporation s. willen (Power Cord) leense, no night (0 reproduce this drawing «s gfanted or the subject matter thereot uniess by writien agreement wath oF written permission ‘rom the Corporation.

Figure 17 Cabinet-Mounted Assemblies A036651-xx B

Page 35

Figure 17 Cabinet-Mounted Assemblies Parts List

Pait No. Description

A021700-01 Coin Box Assembly (for all the same coins) A021700-02 Coin Box Assembly (for two different coin denominations—has one separator) A021700-03 Coin Box Assembly (for three different coin denominations—has two separators) A034841-02 Strain Reliet Power Cord (U.S.)

A034863-02Strain Relief Power Cord(Germany and other countries)
A035989-02Strain Relief Power Cord(Australia)

A034631-01 On/Off Switch Assembly A036189-01 Interlock Switch Assembly (modified for safety) A036247-01 Printed-Circuit-Board Interconnector A036603-01 Main Harness Assembly (a/so includes onloff switch, 2 interlock switches and their brackets, and volume contro! and its bracket)

The following six items are the technicai information supplements to this manual: OP-166-01 Battlezone™ Cabaret Schematic Drawings (Sheet 1) DP-166-02 Battlezone/Cabaret Schematic Drawings (Sheet 2) DP-166-03 Battlezone/Cabaret Schematic Drawings (Sheet 3) ST-166 Battlezone/Cabaret Label with Self-Test Procedure and Option Switch Settings TM-151 Instruction and Service Manual for G05-802/805 Quadrascan™ X-Y Monitor TM-166 BattlezoneiCabaret Operation, Maintenance and Service Manual

19-9032 Volume Controt - 71-2110 Panel Cartridge Lock Mechanism (for access panel) 7507017 Spacer for Mounting Printed Circuit Boards 78-3201 Cabinet-Leveling Leg 78-0003 Ye-Inch-Wide Adhesive Transfer Tape (for mounting overlays on monitor—2 x 9 in. required) 78-24012 §-Inch Beaded Nylon Tie Wrap (for PCB Edge Connectors) 92-045 15:Inch Quadrascan™ X-Y Monitor 002728-01 Control-Panel Mounting Bracket 007882-02 Interlock Switch Cover 009992-01 OniOff Switch Cover 030249-01 Coin Box Separator

034536-02Foam Vibration Damper(for Regulator/Audio |! PCB)
034536-03Foarn Vibration Damper(for Auxiliary and Analog Vector-Generator PCBs)

036130-01 Speaker Grilie 036262-01 Coin Box Bracket 036263-03 Red Monitor Overlay 036263-04 Green Monitor Overlay 036669-01 Acrylic Monitor Shield 036670-01 Monitor Shield Retainer 036674-01 Attraction Panel with Graphics 036676-01 Cardboard Bezel with Graphics 148001-001 6 x9-Inch 4-Ohm 15-Watt Oval High-Fidelity Speaker 035745-02 18-Inch Plastic PCB Retainer 03574503 10-Inch Piastic PCB Retainer

Page 36

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 37

62-039

75017S

75-9910W0 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, inc., Sunnyvale, CA. This drawing is only conditionally i issued, and neither receipt nor possession thered! | confers or transfers any right in, or license to use, the subject matter of the drawing or any design of technical intormation shown thereon, nor any Tight to reproduce this drawing or any part thereot Except for manufacture by vendors of Alati, Inc.. Control Handle Assy.— and tor manufacture under the corporation $ writ Figure 19 {en license. no right 10 reproduce this drawing is ‘See Figure granted or the subject matter thereof uniess by written agreement with or written permission trom the corporation.

03610201

036675-01

005255-04

Figure 18 Control Panel Assembly A036656-01 A

Parts List

Part No. Description

A036246-01 Control-Panel Harness Assembly 62-039 SPDT Momentary-Contact Pushbutton Start Switch with Red Light-Emitting Diode 75-017S 7/16-Inch SAE-Standard Zinc-Piated Steel Flat Piain Washer 76-9910W0 #15/32-32 Steei Stamped Nut

005255-04 Control-Handie Bezel 033127-01 Biack Molded Switch Bushing 036102-01 Wood Support Block for Control Handles 036675-01 Control Panel with Graphics

Page 38

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any design of technical information shown thereon, nor an) right to reproduce this drawing or any part thereo! Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ. ten licenze, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation

The A036271-01 assembly has NO fire switch and harness (left control handle). The A036271-02 assembly HAS the fire switch and harness (right control handle). 72-8614

oN _~

85-22F608 035997-01

035995-01

NOTE: Do not remove the flat actuator spring unless you have a replacement. Removing the spring will bend it, and it will no longer be usable.

Figure 19 Control Handle Assembly A036271-01 and -02

Page 39

Figure 19 Control Handle Assembly Parts List

Part No. Description

A036277-01 Shaft Assembly with Fire Switch Harness (includes pivot ball, pivot shaft and 2 slotted pins) A03627801 Shaft Assembly without Fire Switch Harness (includes pivot ball, pivot shaft and 2 slotted pins) A036281-01 Centering Bellows 62-043 SPST Pushbutton Switch with Red Non-Lighting Cap (used as fire switch) 65-021A Single-Pole Single-Throw Low-Force Miniature Switch 72-1412S #4-40 x %4-Inch Pan-Head Cross-Recessed Steel Cadmium-Piated Machine Screw 72-8614 #6-32 x 7/8-Inch Hex Socket-Head Steel Machine Screw 73-20809 18-Inch Diameter x 9/16-Inch Long Slotted Pin Basar 1 2 3/46-Inch Diameter x 7/8-Inch Long Slotted Pin € 7.2 27:77 4) 75-046 #6 Internal-Tooth Steel Split Lock Washer 75-944S, #4-40 Steel Self-Locking Polymer Hex Nut 78-1710 Dow Corning Heavy Silicone Compound #1114 Lubricant 85-22F608 #6-32 x ¥-Inch Pan-Head Phillips Self-Threading Type F Steel Machine Screw 000609-02 Control Handie Housing (two of these required per contro! handle assembly) 005255-04 Controi-Handle Bezel 035792-01 Straight-Pattern Detent 035844-01 Clear Plastic Actuator Pin 035995-01 Plastic Control Handie (Right Half) 03599502 Plastic Control Handle (Left Half) 035997-01 Plug for Control Handie 036276-01 Bezel for Fire Pushbutton 036279-01 Pivot Ball 036280-01 Pivot Shaft 036282-01 Flat Actuator Spring 178010-001 Nylon Actuator Ball 178016-001 Spring

Note: The control-handle bezel is not part of this control handle assembly. It is listed here for your convenience.
Page 40

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 41

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atari, Inc., Sunnyvale, CA. This drawing 1s oniy conditionally’ issued, and neithe! receipt nor possession thereof confers or transfers any fightin, oF license to use. the subject matter of the draw. ing or any design or technical information sown thereon, ‘nor any right to reproduce this drawing of any pari thereof. Except for manulacture by vendors of Atar, Inc., and for manufacture under the corporation's written license, no right 10 reproduce this drawing 1s granted or the subject matter thereof unless by written agreement 99-11008 with or written permission {rom the corporation. 7 99-11011

99-11003

99-11009

A005493.01

Figure 20 Fluorescent Light A036205-01 Cc

Parts List 035835-01

79-561816P

Part No. Description

A005493-01 Fluorescent Light Harness Assembly 70-304 18-Inch 15-Watt Cool White Fluorescent Lamp 79-561816P Wire Nut for 16- to 18-Guage Wires 99-11003 Fluorescent Lamp Starter

99-11008 Ballast Transformer 99-11009 Starter Socket 99-11011 1¥2-Inch Clamp 035835-01 Y-Lead Connector

Page 42

Battiezone™/Cabaret

034482-02 79-441 1006 034544-01 036304-01 46-2017002 46-2014001

79-3206

A035888-01 or -02 (av) oR 403589101 A036354.01 or -02 (Int'l) Z = (US)

78-2708

TOP VIEW

(F2is not used)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the 78-70501SC specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally’ issued, and neither 29-053 receipt nor possession thereof conters or transters any right in, oF ficense {o vse, the subject matter of the drawing or any design oF technical information shown the:eon, for any fight to reproduce this drawing or any part thereof. Except tor manutacture by vendars of Atari, Inc., and for manulacture under the corporation's written, incense, no right to reproduce this drawing is granted or the subject matter thereo! untess by written agreement with or written permission from the corporation,

BOTTOM VIEW

3A-MDA3501

A035890-01 (Int'l) A034630-01 gy A036355-01 (U.S) N034629-01 79-15021001

Figure 21 International and U.S. Power Supply Assemblies for X-Y Games A035892-01 (International) A / A036353-01 (U.S.) A

Page 43

Battlezone™iCabaret

Figure 21 International and U.S. Power Supply Assemblies for X-Y Games Parts List

Part No. Description (Reference Designations in Bold)

A034629-01 AC. Harness Assembly A034630-01 RFI Fiiter Assembly (FL1) A035674-01 Voltage Plug Assembly (set of four plugs—for international power supply only) A035888-01 or -02 Transformer Assembly—international only (T1) A035890-01 Power Harness Assembly (international only) A035891-01 Fuse Harness Assembly A036354-01 or -02 Transformer Assembly—U.S. only (T1) A036355-01 Power Harness Assembly (U.S. only) 29-053 26,000 uf 15 V Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1)

46-20140014-Amp. 125 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F4, F5, F6)
46-20170027-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F1)
46-30120320-Amp. 32 V 3AG Slow-Blow Glass Cartridge-Type Fuse(F3)

78-2708 Nylon Type 6/6 Hole Bushing with 5/8-Inch Inside Diameter x 55/64-Inch Outside Diameter x Ya-Inch Thick 78-70501SC. 2-Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with ¥%-Inch Quick-Disconnect Terminals 79-4411006 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 084482-02 Power Supply Chassis 034544-01 Fuse Block Cover 036304-01 Label for Fuse Values

Page 44

Battiezone™/Cabaret

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction. tortdden without the Specific written permission of Atan, Inc, Sunnyvale, CA This drawing is only conditionally’ issued, and neither receipt nor possession thereot conters or iransters any right in, or license to use, the subject matter af the drawing oF any design of tectnical informaticn showa therecn, or any tight to reproduce this drawing or any part thereof, Except for manufacture by vendors of Alan, Inc and tor manufacture under the corporation's wiitten license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with of wiitten pecmission from the corporation.

eics8cea
foseirs ¢[7ets273:span ¢3287

es is

mePRRpoag.—
036176dl"VE Je466?ig |o
neeas)paeehetT }8
kJgener eeweawnenA
137004oes+
oseyeane?iame res.1Trie)

. Oo Og)F '

ax=:

03 oo; BEY bl Fa .

ert Oe5[razefarsaEHke
13700¢27casB9eTGTH

2 dence

2361794

= 5321806 137004 2

Tacs, <> a

Pets Ge er! wooare iS £

137004_ea
(acsnt=[aor[aRwsoaeE

ganas pesca

cora294-6l pce ia} R36 j

foseirs §ne(fares(Gewese

Go 3

cqcord|
D>a=_fo)
crBPaRezeare?|

3 SPARE S| omni 2 [(Coosoccosc00pACGNTSOGCF] | 0 lo

0cB626fe)

aD an Id)

Figure 22 Battlezone™ Auxiliary PCB Assembly A035678-01 B

Page 45

Figure 22 Battlezone™ Au: Parts List iary PCB Assembly Battlezone /Cabaret

Part No. Description (Reference Designations and Locations in Bold)

C012294-01Audio I/O N-Channel MOS/LSI Custom Chip(B/C2)

21-101153 015 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor 21-101472 .0047 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor 21-101474 47 uf, +10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C29) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13, 14)

24-250227220 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C27)
24-250477470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C28)
24-5004754.7 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor(C9)
29-088-1 uf Ceramic-Disc Radial-Lead 25V Capacitor(C1-8, 10, 12, 15-20, 23, 24, 26, 30-35)
31-1N91475V Type-1N914 Switching Diode(CR1)
37-LM324Type LM324 Integrated Circuit(K5, MS)
37-4066Type 4066 Analog Switch Integrated Circuit(J3, L4)
37-555,Type 555 Timer (ntegrated Circuit(F3)
37-74LS00Type 74LS00 Integrated Circuit(D3)
37-74LS02Type 74LS02 Integrated Circuit(D4)
37-74LS04Type 74LS04 integrated Circuit(Ea)
37-74LS20Type 74LS20 Integrated Circuit(J4)
37-74LS32Type 74LS32 Integrated Circuit(C4)
37-74LS74Type 74LS74 Integrated Circuit(C5, J5)
37-74LS139Type 74LS139 Integrated Circuit(C3)
37-74LS161Type 74LS161 Integrated Circuit(D1, Ei, F4, F5)
37-74LS164Type 74LS164 Integrated Circuit(H4, H5)
37-74LS273Type 74LS273 Integrated Circuit(M2)
37-74LS374Type 74LS374 Integrated Circuit(C1)
37-74S08Type 74S08 Iniegrated Circuit(D5)
37-74109Type 74109 Integrated Circuit(B4)

38-MV5053 Type MV5053 Red Light-Emitting Diode (CR2)

79-42C1616-Contact Medium-\nsertion-Force Integrated Circuit Socket(B1, F1, H1, J1, K1, L1, M1)
79-42C4040-Contact Medium-Insertion-Force Integrated Circuit Socket(B/C2, D/E2, F2, HiJ2, K2)

020670-01 Test Point

036174-01Programmabie Read-Only Memory(B1)
036175-01Programmable Read-Only Memory(M1)
036176-01Programmable Read-Only Memory(L1)
036177-01Programmabie Read-Only Memory(K1)
036178-01Programmable Read-Only Memory(J1)
036179-01Programmable Read-Only Memory(H1)
036180-01Programmabie Read-Only Memory(F1)
110000-1021K Ohm, + 5%, YW Resistor(R2, 3, 5, 7, 15, 16, 22, 38, 46-52)
110000-10310K Ohm, + 5%, %W Resistor(R13, 18, 30, 36)
110000-124120K Ohm, + 5%. YW Resistor(R11)

{Continued on next page]

Page 46

Battlezone Cabaret

Figure 22 Battlezone™ Auxiliary PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

110000-104 100K Ohm, + 5%, %4W Resistor (R8, 10, 23-25, 28, 31) 140000-151 150 Ohm, + 5%, ‘4W Resistor (R37, 45) 110000-223 22K Ohm, + 5%, v4W Resistor (R9, 14, 17, 29) 110000-333 33K Ohm, + 5%, “@W Resistor (R12, 19-21, 26, 34, 35) 110000-334 330K Ohm, + 5%, %W Resistor (R27, 32, 33) 110000-471 470 Ohm, + 5%, %4W Resistor (R1, 39-44) 110000-472 4.7K Ohm, + 5%, “4W Resistor (R6) 137002-001 Type 74886 Integrated Circuit (E5) 137003-001 Type 74803 Integrated Circuit (3) 137004-001 Transistor Array (D/E2, F2, H/J2, K2) 179010-001 12-Pin PCB Header

Page 47

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 48

Figure 23 Battlezone™ Analog Vector-Generator PCB Assembly Parts List

Memory Components and Their Equivalents (Locations Shown in Bold)

-02 P.C. Boards (ROMs)

036409-01

036410-01

036411-01

036412-01

036413-01

036414-02

036421-01

036422-01 (N1)

(uM)

(K1)

(1)

(e/H1)

(E1)

(a3)

(BIC3)

Page 49

Battiezone MiCabaret

Figure 23 Battlezone™ Analog Vector-Generator PCB Assembly, continued Parts List

Note: The Battlezone™ Analog Vector-Generator PCB consists of the Battlezone memory chips (described on the previous page in the Memory Equivalents Table) PLUS the Universal Vector- Generator PCB. The latter is interchangeable with Battlezone and future X-Y games, but not with Lunar Lander™ or Asteroids™. All the following parts in this figure make up the Universal Vector-Generator PCB Assembly.

Part No. Description (Reference Designations and Locations in Bold)

Universal Vector-Generator PCB Assy., A035742-01 and -02, Rey. B, consists of the following parts:

19-007 10K Ohm, + 20%, 114W 8-Pin Duai-Inline-Package Resistor Network (RP1, RP2—use only if board has 74LS170s or 74LS670s at locations £6, F6, H6) 19-315103 10K Ohm Vertical PCB-Mounting Cermet Trimpot (R88, 98) 19-315201 200 Ohm Vertical PCB-Mounting Cermet Trimpot (R73, 74) 21-101102 .001 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C69, 70, 93, 94)

21-101103 .01 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (For -02 PCB Assy. only: C103) 21-101473 .047 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C56, 59)

24-25010610 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C17, 18)
24-250107100 ut Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C78, 83-86)
24-5001051 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor(C30, 89, 90)

27-102182 .0018 pf, + 10%, Radial-Lead Ceramic-Disc 1000V Capacitor (For -01 PCB Assy. only: C103. For -02 PCB Assy. only: C105)

28-10110010 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C44)
28-101101100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C27)

28-101151 150 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C63) 28-101221 220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C82)

28-10139039 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C25, 64)
28-10147047 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C104)

29-006 1 uf, +10%, 35V Tantalum Capacitor (C88) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-16, 19-23, 26, 28, 29, 31-39, 45, 46, 50-54, 61, 72-77, 79-81, 97, 98. Also, for -01 PCB Assy. only: C40, 41, 48, 49. For -02 PCB Assy. only: C42, 43, 50, 51)

31-1N100100V Type-1N100 Switching Diode(CR11)
31-1N91475V Type-1N914 Switching Diode(CR1, 3-10)
33-2N3906Type-2N3906 PNP Switching and Amplifying Transistor(Q3, 7)

34-2N3904 Type-2N3904 NPN 60V 1-Watt Transistor (Q1, 2, 8, 9) 34-2N6044 Type-2N6044 Darlington NPN Transistor (Q4-6)

37-LM319Type LM319 Integrated Circuit(B12, D12)
37-TLO82CP.Type TLO82 Integrated Circuit(A10, D109)
37-13201Type LF13201 Integrated Circuit(B10, D11, £10)
37-347Type TLO84 Integrated Circuit(C11)
37-74LS00Type 74LS00 Integrated Circuit(J4)
37-74LS02Type 74LS02 tntegrated Circuit(N9, M7)
37-74LS08Type 74LS08 Integrated Circuit(L5, P8)
37-74LS10Type 74LS10 Integrated Circuit(K4)
37-74LS14Type 74LS14 Integrated Circuit(B6)
37-74LS20Type 74LS20 Integrated Circuit(M5)
37-74LS27Type 74LS27 Integrated Circuit(N7)
Page 50

Battlezone”/Cabaret

Figure 23 Battlezone™ Analog Vector-Generator PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

Universal Vector-Generator PCB Assy., A035742-01 and -02, Rev. 8, consists of the following parts:

37-74LS32Type 74LS32 Integrated Circuit(J5, K10, L2, M8)
37-74L842Type 74LS42 Integrated Circuit(B4, J7)
37-74LS74Type 74LS74 Integrated Circuit(H10, L10, M9)

37-74LS86 Type 74LS86 Integrated Circuit (D7)

37-74LS109Type 74LS109 Integrated Circuit(N8)
37-74LS 139Type 74LS139 Integrated Circuit(Ca, K5, M2)
37-74LS157Type 74LS157 Integrated Circuit(D4, E4, F4, Ha)
37-74LS161Type 74LS161 Integrated Circuit(K6, L4, L6, M6, N6)
37-74LS164Type 74LS164 integrated Circuit(P9)
37-74LS174Type 74LS174 Integrated Circuit(C7, L7, M11)
37-74LS175Type 74LS175 Integrated Circuit(F8, F9, J8, K8)
37-74LS191Type 74LS191 Integrated Circuit(F10, J6)
37-74LS193,Type 74LS193 Integrated Circuit(E5, F5, H5)
37-74LS194Type 74LS194 Integrated Circuit(A5, A6, B5, C5, D5, D6)
37-74L8244Type 74LS244 Integrated Circuit(K3, N2, N11, P11, R11)
37-74LS245,Type 74LS245 Integrated Circuit(F2,P2,P4) Acceptable substitute is part no. 37-8304B,
37-74LS273Type 74LS273 Integrated Circuit(C8)
37-74LS367Type 741.S367 Integrated Circuit(F7, H7)
37-74LS393Type 74LS393 Integrated Circuit(M4, N5)
37-74LS399Type 74LS399 Integrated Circuit(H8)
37-74LS670Type 74LS670 Integrated Circuit(E6, F6,H6)Acceptable substitute is part no. 37-74LS170.
37-74S00Type 74S00 Integrated Circuit(C6)
37-74S802Type 74802 Integrated Circuit(K9)
37-74804Type 74S04 Integrated Circuit(K2, R9)
37-74874Type 74S74 Integrated Circuit(J10, L9)
37-74S260Type 748260 Integrated Circuit(L8)
37-7404Type 7404 integrated Circuit(H11)
37-74193Type 74193 Integrated Circuit(N4)
37-7805+5V Voltage Regulator(VR2)

37-7815 + 15V Voltage Regulator (VR3)

37-7915,— 15V Voltage Regulator(VR1)

38-MV5053 Type MV5053 Light-Emitting Diode (CR2) 41-3004 100 uH, + 10%, Hot-Molded Plastic Fixed R.F. Choke (L1) 62-001 SPST Momentary Pushbutton Switch (SW1) 66-114P1T 4-Station Single-Throw, Dual-Inline-Package Bit Switch (111) 66-118P1T 8-Station Single-Throw, Dual-In\ine-Package Bit Switch (M10, P10) 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (A3, B/C3, D3, E1, E3, F/H1, F/H3, J1, J3, K1, M1, Ni) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (L/M/N3) 81-4302 Nylon Snap-In Fastener

90-10212.096 MHz, +.005%, Crystal(¥2)

90-6013 Microprocessor (L/M/N3)

90-7033Random-Access Memory(A1, A2, B1, 82, C1, C2, D1, D2, H2, J2)

02067001 Test Point

036408-01Programmable Read-Only Memory(K7)
Page 51

Figure 23 Battlezone™ Analog Vector-Generator PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold)

Universal Vector-Generator PCB Assy., A035742-01 and -02, Rev. B, consists of the following parts:

110000-101100 Ohm, +5%, %4W Resistor(R70, 75)
110000-1021K Ohm, +5%, %4W Resistor(R18, 20, 27, 67, 84-86, 94, 110, 128-133)

110000-103 120 Ohm, +5%, %W Resistor (R1-17, 19, 21, 25, 26, 33, 44, 51-66, 95, 99, 125-127. In addition, for -01 PCB Assy. only: R48, 50, 69) 110000-104 100K Ohm, +5%, %4W Resistor (R35-42)

110000-1221.2K Ohm, +5%, %W Resistor(R46)

110000-151 150 Ohm, +5%, YW Resistor (R103)

110000-15315K Ohm, +5%, YW Resistor(R93)
110000-221220 Ohm, +5%, %4W Resistor(R24)

110000-222 2.2K Ohm, +5%, VsW Resistor (R45, 92, 102, 112, 114-116, 119-121, 123)

110000-22322K Ohm, +5%, %4W Resistor(R28-32)

110000-270 27 Ohm, +5%, YW Resistor (R111) 110000-332 3.3K Ohm, +5%, %4W Resistor (R87, 97) 110000-392 3.9K Ohm, +5%, %W Resistor (R47, 49) 110000-471 470 Ohm, +5%, %W Resistor (R34, 104-109) 410000-472 4.7K Ohm, +5%, YW Resistor (R43) 110000-474 470K Ohm, +5%, %4W Resistor (R113, 117, 118, 122) 110000-561 560 Ohm, +5%, YW Resistor (R96)

110000-68068 Ohm, +5%, YW Resistor(R124)

110000-681 680 Ohm, +5%, %4W Resistor (For -02 PCB Assy. only: R83) 110000-821 820 Ohm, + 5%, %W Resistor (For -02 PCB Assy. only: R68, 69, 82) 110003-752 7.5K Ohm, +1%, 1/8W Metal-Film Resistor (R71, 72, 76-81, 89)

122000-2252.2 uf, + 10%, 35V Tantalum Capacitor(C87)

122005-103 .01 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor (C47, 55, 57, 58, 60, 62, 65-68, 71, 91, 92, 95, 96, 99, 100)

137002-001Type 74886 Integrated Circuit(B7)
137149-001Type 74LS11 Integrated Circuit(J9)
137159-001Type DAC-08 Digital-to-Analog Converter(C9)

137158-002 Type AM6012ADC Digital-to-Analog Converter {(A9, D9) For -02 PCB Assemblies only OR OR

137160-003Type MC3410 Digital-to-Analog Converter(B9, E9)For -07 PCB Assemblies only

179010-001 12-Pin PCB Header (J19)

Page 52

Battlezone Cabaret

3015 311SOadO NO 2Yv NMOHS S30VHL

Figure 24 Regulator/Audi A035435-02 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Reproduction forbidden without tne specific writen permission of Atan, nc, Sunnyvale, CA This drawing is only conditionally’ issued, and neither receiot nor possession thereo! confers or transters any fight in, or Heense to use, the subject matier of the draw ing oF any design or technical intormation shown thereor, nor-any righl to repraduce this drawing ar any part thereot, Except for manufacture by vendors of Atari, Inc and for manulacture under the corporation's written Ticense, no right to reproduce this drawing Is granted oF Ihe Subject matter thereof uniess by written agreement with 9r written permission trom the Corporation

Il PCB Assembly

Cc

Page 53

Figure 24 Regulator/Audio Ii PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Boid)

12-52P7 2.7 Ohm, + 5%, 1W Resistor (R5) 16-54PO 4 Ohm, +5%, 5W Wirewound Resistor (R25) 19-100P 1015 -1 Ohm, + 3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8) 24-250108 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-350226 22 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C24, 31) 24-350338 3300 ut Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19) 24-500105 1 ul Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C22, 23) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21) 31-A14F 50V 2.5A Miniature Axial-Lead High-Current Rectifier (CR1, 4-8) 33-TIP32 PNP Power Transistor, Type TIP32 (Q2) 34-2N3055 NPN Siticon Transistor, Type 2N3055 (Q3) 37-LM305, 8V Linear Voltage Regulator (Q1) 37-7812 +12V Voltage Regulator, Type 7812 (Q8) 37-7905 —SV Voltage Regulator, Type 7905 (Q9) 72-1608C #6-32 x Ve-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 75-F60405, #6-32 x Va-Inch Binder-Head Nylon Screw 75-99516 #6-32 Nut/Washer Assembly 78-16008 Thermally Conductive Compound (Q3) 78-16014 Thermally Conductive Silicon Insulator (Q2, 9) 79-58306 6-Position Connector Receptacle (J6, 9) 79-58308 9-Position Connector Receptacle (J7) 79-58346 12-Position Connector Receptacle (J10) 79-58354 4-Position Connector Receptacle (J8) 020670-01 Test Point 034531-01 Heat Sink 110000-010 1Ohm, + 5%, %W Resistor (R10, 19) 110000-100 10 Ohm, + 5%, “4W Resistor (R11, 20, 29, 30) 110000-101 100 Ohm, + 5%, YW Resistor (R4, 12, 22) 110000-102 1K Ohm, + 5%, %4W Resistor (R27, 28) 110000-103 10K Ohm, + 5%, %W Resistor (R13, 14) 110000-271 270 Ohm, + 5%, VaW Resistor (R1) 110000-330 33 Ohm, + 5%, %W Resistor (R3) 110000-392 3.9K Ohm, + 5%, YW Resistor (R6) 110000-562 5.6K Ohm, + 5%, %W Resistor (R32, 33) 110000-752 7.5K Ohm, + 5%, %W Resistor (R7) 110001-221 220 Ohm, + 5%, YeW Resistor (R9, 21) 116000-220 22 Ohm, + 5%, 10W Wirewound Resistor (R31) 122002-102 -001 uf Ceramic-Disc Minimun 25V Radial-Lead Capacitor (C2, 7, 16) 122004-224 -22 uf Ceramic-Disc 25V Capacitor (C6, 8, 15, 17) 100015-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, C14) Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit (Q5, 7) 137151-002

Page 54

99-10073

id a

PART OF 99-10095

o \

A

COIN INLET cuuTe 9.10097

(31 P COIN MECHANISM ee, SEE PARTS LIST Se - 14 / " a P 99-10102 65-441C / a COIN RETURN { —99-10065 SWITCH WIRE CHUTE 9910068 __/ SEE PARTS LIST (99-10075 thru siineie ; . COIN switcn aséy, | 991078) PART OF 99-10047 SEE PARTS LIST Se-10008 99-10082 (99-10042 thru 75-1412S 99-10045)

Figure 25 Coin Door 71-10xxxx

Page 55

Battlezone Cabaret

COIN RETURN BUTTON COVER— SEE PARTS LIST (99-10055 thru 99-10059)

COIN RETURN BUTTON ASSY.— SEE PARTS LIST PRICE PLATE— SEE PARTS LIST (99-10012 thru 99-10022, (99-10070, 99-10083. 99-10074 and 99-10107) thru 99-10092, and 99-10108) 72-JA1405B COIN DOOR ONLY— SEE PARTS LIST (99-10009 and 10010) 99-10062

72-HA1404C,

PART OF 99-10074

99-10049

99-10061 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific wriiten permission of Atari, Inc., Sun nyvale, CA. This drawing is only conditionally Issued, and neither receipt nor possession thereat conters or transters eny right in, or license to use, the subject matter of the drawing or any design of technical information shown thereon, nor any fight to reproduce this drawing or any part thereof Except for snanufacture by vendors of Atari, inc., land for mantfacture under the corporation's writ {en license, ne right to reproduce this drawing 1 Granted or the subject matter thereot unless by witten agreement with or written permission {rom the corporation. 99-10066

75-915S / 99-10051 72-JA14058

71-102201 — 25¢/25¢Coin Door 71-103202 — 25%/25¢125¢ Coin Door 71-103203 — 25¢/25¢/$1 Coin Door 71-102204 — 2 DM/1 DM Coin Door 71103205 — 1{2/5 DM Coin Door 71-102206 — 1 DM/5 DM Coin Door 71-102207 — 5 FriS Fr Belgian Coin Door 71-102208 — 1 Fri1 Fr Swiss Coin Door 71.102209 — 190Y/100Y Coin Door 71-192210 — 10 P/10 P Coin Door

Figure 25 Coin Door 71-10xxx 71-102211—20¢/20¢ Australian Coin Door 71-102212—100 L/100 L Italian Coin Door 71-102213 — 50¢/50¢ (2 x 25¢) Coin Door 71-103214 — 50¢/50¢/50¢ Coin Door 71-103215 — 50¢/50¢/$1 Cain Door

Page 56

Battlezone Cabaret

Figure 25 Coin Door, continued Parts List

Part No. Description

31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-441C General-usage low-force miniature switch 70-11-47 Miniature bayonet-base incandescent lamp, type #47 71-1201ADU U.S. $1.00 coin mechanism 71-1201FCH Swiss 1 Fr coin mechanism 71-1201MG German 1 DM coin mechanism 71-1202MG German 2 DM coin mechanism 71-1205FB Belgian 5 Fr coin mechanism 71-1205MG German 5 DM coin mechanism 71-1210PE U.K. 10 P coin mechanism

71-1220CA Australian 20¢ coin mechanism 71-1225CU U.S. 25¢ coin mechanism 71-12100LI Italian 100 Lire coin mechanism 71-12100YJ Japanese Y100 coin mechanism 72-HA1404C #4 x Va-Inch slotted pan-head thread-rolling tri-fluted “Taptite” cadmium-plaied screw 72-JA1405B #4 x 5/16-Inch slotted pan-head thread-rolling tri-fluted “Plastite” black screw 72-9406S #4-40 x 3/8-Inch slotted truss-head steel machine screw 72-9603S #6-32 x 3/16-Inch slotted truss-head steel machine screw 75-915S #%%4-20 Standard pattern cadmium-plated steel hex nut 75-918S #8-32 Standard pattern cadmium-plated steel hex nut 75-9448, #4-40 Polymer seli-locking steel hex nut 75-9488, #8-32 Polymer self-locking steel hex nut 75-1408S #4-40 x ¥2-Inch slotted pan-head steel machine screw 75-1412S #4-40 x %4-Inch slotted pan-head steel machine screw 75-5520B. #%4-20 x 1%-Inch round-head square-neck steel bolt with black finish 99-10008 Switch wire retainer 99-10009 2-Mech coin door only 99-10010 3-Mech coin door only 99-10011 Inner panel 99-10012 U.S. 25¢ coin return button assembly 99-10013 U.S. $1.00 coin return button assembly 99-10014 German 1 DM coin return button assembly 99-10015 German 2 DM coin return button assembly 99-10016 German 5 DM coin return button assembly 99-10017 Belgian 5 Fr coin return button assembly 99-10018 Swiss 1 Fr coin return button assembly 99-10019 Japanese Y100 coin return button assembly 99-10020 U.K. 10 P coin return button assembly 99-10021 Australian 20¢ coin return button assembly 99-10022 Italian 100 Lire coin return button assembly

Page 57

Figure 25 Coin Door, continued Parts List

Part No. Description

99-10045, Coin switch assembly for German 5 DM, U.K. 10 P, and Australian 20¢ coins (green wire) 99-10047 Lockout coil assembly 99-10048 Coin door harness assembly 99-10049 Locking arm assembly 99-10051 Coin door frame 99-10052 Coin return lever 99-10054 Coin button housing 99-10055 Coin return button cover for Japanese Y100 coin 99-10056 Coin return button cover for German 1 DM and Swiss 1 Fr coins 99-10057 Coin return button cover for U.S. 25¢ and Belgian 5 Fr coins 99-10058 Coin return button cover tor U.S. $1.00, German 2 DM, and Italian 100 Lire coins 99-10059 Coin return button cover for German 5 DM, U.K. 10 P, and Australian 20¢ coins 99-10061 Coin return bezel 99-10062 Coin return button 99-10063 Right half of coin inlet chute 99-10064 Left half of coin inlet chute 99-10065 Coin return box 99-10066 Coin return cover 99-10070 U.S. 25¢ price piate 99-10071 Siam switch assembly 99-10073 Test switch decal 99-10074 Lock assembly 99-10075 Black switch wire—for German 1DM, Swiss 1Fr and Japanese Y100 coins 99-10076 Silver switch wire—for U.S, 25¢ and Belgian 5Fr coins 99-10077 Gold switch wire—for U.S. $1.00, German 2DM and Italian 100 Lire coins 99-10078 Green switch wire—for German 5DM, U.K. 10P and Australian 20¢ coins 99-10080 Miniature bayonet-base lamp socket 99-10081 Wire key holder 99-10082 Switch cover 99-10083 U.S. $1.00 price plate 99-10084 German 1 DM price plate 99-10085 German 2 DM price plate 99-10086 German 5 OM price plate 99-10087 Belgian 5 Fr price plate 99-10088 Swiss 1 Fr price plate 99-10089 Japanese Y100 price plate 99-10090 U.K. 10 P price plate 99-10091 Australian 20¢ price plate 99-10092 Italian 100 Lire price plate 99-10094 Fish paper insulation 99-10095 Toggle switch 99-10096. “U"-type fastener 99-10097 Fish paper insulation 99-10101 Coin inlet chute sub-assembly 99-10102 Switch and lockout coil bracket sub-assembly 99-10103 Inner panel with levers sub-assembly 99-10104 Anti-penny-flip bar retainer 99-10105 Anti-penny-flip bar 99-10107 U.S. 50¢ coin return button assembly 99-10108 U.S. 50¢ price plate—for two quarters

Page 58

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 59

eS 2nd printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person

Page: Comments:

Fill in if you wish a reply

Name

Firm = |) Distributor

Address - _ . LJ Operator

City _. ~ State. “ a UJ Other —

AreaCode ________ Phcne __

Page 60

First told

No Postage Necessary it mailed in the United States

bead

aul siyy Guoje jn be BUSINESS REPLY MAIL — FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA a

POSTAGE WILL BE PAID BY ADDRESSEE |

Atari, Inc. ee Attn.: Field Service/Coin-Op Division ~_Y P. O. Box 427 Sunnyvale, California 94086 . eC be |

_ Second fold

W014

a6pe si odey

Page 61

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

@ EEE EEE

©@ »

s

Warranty

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty

  • days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

RSS SS AS ES The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 64

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.