CATHODE RAY TOMES

Alien Attacker (Suntronics )

Alien Attacker (American Sun-Tronics Inc.) · Manual · 32 pages · 23 sections · original scan

Page 1

1865 WICKHAM ROAD ¢ MELBOURNE, FLORIDA 32935

OPERATIONS

&

REPAIR MANUAL

Manufacturer Of Quality Video Games

Page 2

CONTENTS

PAGE SPECIFICATIONS ....................... 2

INTRODUCTION .... 6... el 4

GENERAL PRACTICES ................... 7

POWER SUPPLY ....................0.., 11

GAME LOGIC BOARD...................., 1s

GONTROLS ...... el, 16

MONITOR ........ 0.0... ee eee 19

COINDOOR.........................., 23

DIAGRAMS AND SCHEMATICS.............. 26

Page 3

SPECIFICATIONS

(1,)

(2.)

(3.)

(5.)

(6.)

(7) Power Supply - 120+ 5% Power Consumption - 70W

Size:

Arcade - 25" Width X 30" Depth X 72" Height Mini - 27" Width X 18" Depth X 58" Height Table - 29%" WidthX 24" Depth X 27%" Height

Weight: Arcade - 275 pounds, 298 Net Shipping Weight Mini - 165 pounds, 186 Net Shipping Weignt Table - 165 pounds, 186 Net Shipping Weight

Coinage - One (1) or two (2) coins per play, one coin

for ane player, two coins for two players.

Number of Players: One (1) or two (2) players.

Accessories: Operations Manual - One Copy Keys for Maintenance Door - Two pieces. feys for Cash Door - Two pieces.

Page 4

feed | mer a Gis Tronics = _

Page 5

INTRGOUCTION

Repair of American Suntronics Universal Video Games is by module adjustments, repair or replacement.

There are five modules with interconnecting cables

in these games.

These modules are:

  • Game Logic Soard
  • Monitor
  • Power Supply Assembly
  • Control Panel Assembly
  • Coin Door Assembly

The procedures in this manual will localize the fault to the defective lead, contact or module. Adjustments, fuse replacement and cable repairs can be made at location. Defective modules are returned to the repair station.

No special tools are required by the repair procedure. A digital volt/ohmeter, Radio Shack 22-197 or equivalent, and several test lead jumpers are necessary. The standard tool box compliment of soldering iron, (not a soldering gun) and hand tools will also be needed to make cable and electro-mechanical repairs.

The schematics and diagrams provided in this manual and with the game logic board are all that are required for in-field troubleshooting and repair.

Page 6

COIN DOOR

LIGHTS MONITOR

wanna rican, Tronics.

FIGURE 1

Page 7

COIN DOOR

a

Page 8

GENERAL PRACTICES

Game Malfunction Preliminary Inspection Always inspect the cabinet for damage that might indicate the nature and possible cause of the fault.

For example: No Power .- Could be the result of a cut AC line

cord.

Not Accepting Coins - Could indicate a foreign object in acceptor slot. Be certain the AC outlet is active and the AC line switch

is on. (Located at rear right of cabinet at bottom). With

Power applied, the fan will be running. If the fan is not on, remove the panel. Check P7 & P8& (Fig 8) for proper seating to determine if a fuse is defective. The best method is to test

with the DVM (Digital Volt/Ohmeter) set to ohms scale. The meter will indicate a short (O00) for a good fuse.

With AC power applied and the fan running,the coin door lights will be lit. If the lights are out, test the +5 VDC fuse.

Module Access

All procedures require that the game be opened to gain access to the modules and cable assemblies to be tested.

Access to the control panel is gained through the coin door. The control panel is easily removed. The panel is held in place by two carriage bolts and wing nuts, Fig 7. The Carriage bolts are located one on either end of the control Panel. The wing nuts can be removed through the coin door opening. Once the wing nuts have been removed the panel can be lifted out af place and the controls are readily accessable. Inspect all connectors to insure they are properly seated. Inspect the edge connector for proper alignment with the logic board.

Page 9

GENERAL PRACTICES (con't)

Without exception, the +5 VOC is the most important and critical factor in the game. The + 5 VDC can be checked

at the coin door (Fig. 1). If this voltage is low (4.95 to 4.99 volts) the game will present intermittent faults.

Some examples: a. Accepts a coin, display reverts to the test pattern, then back to attract mode.

b. Accepts coin, game starts and suddenly all motion will stop. It will restart only when power is shut off and turned back on.

c. Accepts coin, the game plays normally, then suddenly goes to test pattern. These are only three of many such occurances when the +5 VDC is low.

If the +5 VDC is below 4.95 volts, generally the screen will be blank, as if the game were off. The coin door lights will not be lit. All indications are a defective logic board. It is recommended that the +5 VDC be checked on each

service call to insure it is within the range needed for proper

operation of the logic board. Measuring the +5 VDC can be readily accomplished at the coin door. Connect the DVM between pins 1 &'4 of P9. (Fig 4) or read it directly across the coin door lights. The meter shcould indicate 5.00 volts. This reading assures the proper

operating voltage at the logic board. If adjustment is necessary, refer to power supply section. For all other procedures and adjustments, it will be

necessary to remove the rear panel.

Page 10

FIGURE 2 POWER SUPPLY

Page 11

AC LINE SWITCH

FAN

AC OUTPUT TO MONITOR oO

AC LINE FUSE 3AMP SLO-BLO

AC INPUT

FAN NIC

FIGURE 3 + 12V DC “oO

+5V DC (RED) —5V DC

GROUND: (BLACK) +12 DC (GREEN)

—5V DC (YELLOW)

Page 12

POWER SUPPLY

The power supply enclosure is red and located in the bottom of the cabinet (Fig 2). All AC voltages are delivered to and from P8. The three OC voltages and ground are at P7. The DC power source is contained within the enclosure.

To gain access to the power source, it is necessary to remove the front panel with the four fuses and P7 and P8, (Fig 4&). Remove the AC power input. Remove the six hexagon head screws and lay the panel on the bottomof the cabinet. It istmow possible to adjust the voltages. It is recommended that the enclosure be removed also. This is accomplished by removing the four hexagon screws holding the enclosure to the base and lifting it straight up. AC power can now be restored.

cAUTION

Extreme care must be exercised due to the exposed voltage

and connections.

The DC power source supplied with the cabinet may be either a TD 75wor TD 60w as shown in Fig. 5. It is of no importance which DC source is supplied. Both are equally capable of supplying the required voltages and current. Refer to the diagram for the power source under test for

the voltage adjustment.

NOTE: These power sources are designed with an over voltage

protect circuit in the +5 VDC power source. If this voltage is adjusted beyond approximately 5.6 volts, the voltage indicated on the DVM suddenly decreases to less than 1 volt. If this occurs, remove the AC power and move the +5 V ADJ

one quarter turn counter clockwise. Re-apply AC power.

~141-

Page 13

POWER SUPPLY(con't)

The +5 VDC can be adjusted by connecting the DVM across the terminals of the coin door lights or between pins 1 and & of P93. Place the meter inside the cabinet so it can be observed.

To increase the voltage, SLOWLY turn the +5V ADV clockwise. To decrease the valtage, turn the control counter clockwise. The +12 VDC can be measured between pins 2 & G of P7 using the proper control as indicated in Fig 5. Increase the valtage by turning clockwise and decrease by turning counter clockwise.

Negative 5 VOC can be measured between pins 3 & 4 of P7, Adjust the proper control in the same manner as the +12 VDC.

Oue to the large selection of game boards, from the simple to the complex, the current requirements vary from board to board. Changes in current demand affect the +5 VDC. When logic boards are changed, the +5 VDC must be measured and adjusted to 5.00 volts if necessary.

~12-

Page 14

POWER SUPPLIES

FIGURE 5

Page 15

-l4- POWER SUPPLIES 16000MF 15V @) @) it) -12V

YELLOW

BLACK

[smn] 7

Page 16

Ya GAME LOGIC BOARD

The logic board is an important, fragile piece of electronic equipment to be handled with care, Fig. 4G.

It is recommended that only qualified technicians, familiar with micro-processor circuits attempt any in-depth troubleshooting with these boards. This is not to imply that someone familiar with logic boards, using caution, cannot adjust the controls for the desired operation of the game. The main volume control and the DIP switches are the only user controlled functions on the logic board. The volume control is used to adjust the overall desired sound level.

The DIP switches select the number of characters or rounds

per player, coins per play, and bonus level. Some games have more switches for other functions. the switches are explained in the data supplied with the game board. For the location of the volume control DIP switches and -— their functions, refer to the game logic data.

TYPICAL

MONITOR GAME

CONNECTOR CONTROL LoGic CONNECTOR BOARD

POWER Y a CONNECTOR GAME LOGIC BOARD BOLE WITH MINI-HARNESS CONNECTOR ier

Page 17

CONTROLS

Fig. 7 shows typical controls used in all American SunTronics control panels. The number of pushbuttons and joy sticks, as well as the controls are the same for all control

Panels. All wires from all control panels are connected to 15 pin connectors to adapt to the universal harness. In many cases

not all 15 locations are used. The number of wires connected

depends upon the number of controls used for a particular game. The most frequent cantrol panel malfunction is that the

character displayed on the screen does not respond to the control. Generally, this is due to the springs not making contact when the pushbutton is depressed, or the control stick is moved.

The cause of this problem is the great amount of use these controls receive. They are readily adjusted, (refer ta Fig. 7)

by grasping point 8 on the pushbutton or 3 aon the joy stick assembly with a pair of needle nose pliers and bending the leaf until it nearly touches the actuator when pressure is released. Then grasp the pushbutton at point 7 and the joy stick assembly at point 4 and bend until the clearance between the contact is approximately at 1/8 inch when the pressure is released.

When the contact is closed, there should be some movement of the outerleaf. This movement, or wiping action is a self- Cleaning action to help reduce the oxide and dust build-up on the contact surfaces. If intermittent control malfunction is

experienced, the contacts can be cleaned by placing a piece of bond paper between the contacts, closing the contacts and withdrawing the paper. In the event the control is still not functioning, connect the DVM at points 1 8&8 2 of the joy stick assembly, or the Pushbutton. The DVM will indicate approximately 4.5 volts. Closing the contacts will decrease this reading to O volts. If no voltage is present, inspect cable for faulty wire or

~16-

Page 18

CONTROLS (con't)

connection. If the voltage is present and decreases to O volts

when the contacts are closed, suspect a faulty logic board.

CONTROLS

PUSH BUTTON ASSY

FIGURE 7

Page 19

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 20

MONITOR

All controls have been set at the factory for optimum display of each game. When game logic boards are changed, it may be necessary to make some minor adjustment to the controls illustrated in Fig. 3.

Occasionally, when a new game board -is installed, the picture will appear upside down. This is a result of methods of programming the logic board. It is not a malfunction of the game. It is easily corrected by changing lead positions on the deflection yoke of the picture tube. Refer to Fig. 8, items 1,2,3,8 4. The lead colors are RED, BLUE, YELLOW, and GREEN. The position for the leads depends upon the logic board for the particular game.

NOTE: The RED and BLUE leads are always on the outer terminals. The GREEN and YELLOW are always on the inner terminals. These leads are connected to the yoke terminals with fast on connectors. They are removed by grasping the end and pulling

upwards gently. To invert the display: Remove power to cabinet.

Remove leads frompins 1 & 4 and reverse their

location.

Remove leads from pins 2 & 3 and reverse their

location.

This completes the display inversion.

Restore power to the game and make any adjustments necessary refering to Fig. 9 for control and location.

Page 21

RED DRIVE

BLUE DRIVE

MONITOR

REARVIEW

FIGURE 8

RED CUTOFF

GREEN CUTOFF

BLUE CUTOFF

Page 22
  • HORIZONTAL FREQUENCY

With the monitor being driven from the game signal, set the horizontal hold control to its mechanical center and short TP 32 to ground. Adjust the horizontal oscillator coil (screwdriver adjustment) until picture stops: sliding horizontally. Do not use the horizontal hold control for horizontal centering (See #3). NOTE: When the game sync is composite, use horizontal syne input.

  • PICTURE SIZE

Adjust the vertical size control, and the horizontal width coil for desired picture size.

w PICTURE CENTERING

If the video is off center vertically, move the vert raster position adjustment(yellow wire) to the up or down position. If the video is off center horizontally, adjust the horizontal video position control to center the picture. If any additional horizontal positioning is required, move horizontal raster position adjustment (red wire) to the left or right position.

  • BLACK LEVEL

Adjust the black level control to obtain the proper black level (the black portion of the picture just extinguished). Do not use the screen control (on neck PCB) to set the black level.

  • FOCUS

Adjust focus control for best overall definition and fine picture detail.

Page 23

BLACK LEVEL HORIZONTAL Osc COIL (1351)

RASTER HORIZONTAL VERTICAL

POSITION Y WIDTH COI L702 HOLD

XN

R328

‘TP32 { LOWER END OF R328) \ Neem! S.

\ . VERTICAL HORIZONTAL Se eee

VIEDO HORIZONTAL POSITION HOLD HORIZONTAL VR35! RASTER POSITION

MONITOR CONTROLS FIGURES

Page 24

COIN DOOR

There are four possible malfunctions that may occur in the coin

door. Refer to Fig. 4 and Fig. 10.

  • Lamp Out: If the lamps are out, replace lamps. In case the lamps are out and there is no display on the monitor, refer to the section on power supply.
  • Will not accept coins. This problem is usually caused by oils and dirt from the coins. Remove the acceptor, wash in hot soapy water and shake excess water from acceptor and dry with warm air,

such as a hair dryer.

  • Accepts coins, will not register credits. Usually caused by a jammed credit switch wire, or faulty

credit switch.

Remove the credit switch covers and inspect coin chutes for foreign objects. The credit switch wires should be horizontal to the credit switch and move freely when

depressed. Separate P39 and J9. Using the DVM set to the ohms scale, Measure the resistance across the black and white in

39 pin 3 & 4&4 The DVM should indicate open. Depressing either of the credit switches will indicate a resistance

-on the DVM indicating a properly functioning switch. If the meter indicates a shorted switch, unsolder the black

and white wires from one of the switches and determine which is defective using the DVM.

4&. Coin counter not registering. The coin counter aperates from the +5 VDC line. If the

coin door lights are lit, 5 volts is J9 pin 1. Measure the resistance of coil on the coin counter

across pins 1 & 2 of J9. The DVM will indicate approximately 35 ohms.

Page 25

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 26

NOTES

Page 27

DIAGRAMS & SCHEMATICS

PAGE UNIVERSAL WIRING HARNESS.............. 27

WELLS GARDNER MONITORS .............. 28

CONDOR POWER SUPPLY................, 3s

COINDOOR...............00..00......, 37

Page 28

VLVG GYVO8 AWVD 91907 33S SSINYVHINIW y

WIRING DIAGRAM

ng 31 BROWN if > < RED 2 7 $

SSonance33s

38 YELLOW ae $ 4 VIOLET, 7 CONTROLS

gs GREEN 5 Es $ SS piu 6$s

Oo eR a ne 2 > REFER TO Loic BOARD >> aanTe > > DATA HIT 9 22 BROWN 10 =o > JB PB

SS stackuss1_GREEN
YELLOW14 4ri oo
SS seenTESSSs
S$ 2? RED+5Vv 0c1% $1 5 27| ran |
33 GREEN + 12V0C2 ca25A
SS ettow__ sv oea$$35<e
SSstack _Grounp43s4si
55$ u
aa RED+5v 0caed7 422

SS—wmovet co counter 7 $ SS waite crepit switcy 8 § > BLACK GROUND y i a}

>BROWN SPEAKER>1 >
> BROWN _ SPEAKERRY 525
10-110><s5CREDIT

SWITCHES So]

P33P6 JGsay dit
S$ ReDVIDEO1RED
ine GREEN VIDEOze 2GREENss
SS sive vipeo335BLUEcc!
> BLACK GROUND4 >BLACK<
>> WHITE SYNC& > 2ee
>>6>><<

<< << WHITE < rod MONITOR

Page 29

TT wells-qardner electronics com CORPORATION REVISION #1

19” IN-LINE COLOR MONITORS

MODEL

MODEL ~——-19 K4655 enna

wells-qardner electronics

CORPORATION

2701 NORTH KILDARE AVENUE CHICAGO, ILLINOIS 60639

Page 30

AC Input:

DC Output:

Input Fusing:

Reverse Voltage Protect Remote Sensing:

Stability :

Cooling :

Efficiency :

Vibration:

Shock: Temperature Rating:

Temperature Coefficient: Cond 4880 ADOHR LANE | ermation contoineds A

CAMARILLO, CALIF.PaSeg]
3.zt tiaz
ONDOR inc.93010Seat ninei]&

De. POWER SUPPLIES (805) 484-2851 5. General User information e935 a

lz la 3| O10 spel=

SPECIFICATIONSi]Zi

| 2 |i z

115/230vact10% 47-440Hz.AC CONNECTION TABLEa hk

(Derate output current 10% for SOHz Operation.) | FOR USE AT | 11S vac_| 230 VAC ae

Refer to Voltage/Current Rating Chart. VoltageJUMPER183,264]2 63FO
adjustable +5% minimum.APPLY AC _AT1a 41&4

Refer to AC Connection Table. FUSE INPUT AT] 2.0 AMPS] 1.0 AMPS Line Regulation: +0.05% for 10% input change.

Load Regulation:+0.05% for 50% load change. _VOLTAGE CURRENT RATING CHART
Output Ripple::3.0mv mere aaywy.MODELOUTPUT RATING
Transient Reponse:3Op seconds forf, load change.CBB-75WSv. AT 6.0A. W/OVP|

Short Circuit ond

:..OvP SET AT

Overload Protection: Automatic current limit/foldback. 6.2+.4V.

ion: Provided on Dual and Triple output units. Provided on outputs above iSwatts, open sense lead protection built-in. +0.05% for 24hours after warm-up. O°C to 50°C full rated, derated linearly to 40% at 70°C. +0.02%/°C maximum, 0.002%/°C typical. Units are full rated SO°C in free air, must be derated or fan cooled when mounted in confined area. 5V units-45%, 12 and I5V units- 55%, 20 and 24V units - 60% at nominal input, full load on output. Per Mil-Std-810B, Method 514, Procedure |, curve AB (to SOHz). +12V. AT 1.7A. OR *_ +15v. AT ISA I5V. USEABLE AT -5V. AT

  • BY JUMPERING Ei TO E2

2 YEAR GUARANTEE CONDOR will repair or replace any power supply of its manufacture that does Inot perform to published specifications as la result of defective materials or workmanship for a period of 2 years from date of original purchase.No other obligations or fiabilities are implied or expressed. Returns must be freight prepaid. “OR veReTION.

"D FOR PRODUCTION

A | APP’ Per Mil-Std-8I0B, Method 5I6, Procedure V.

Dc ouTPUTS

Byok:oveSy:5
aestoptionany$2889?

re2zo

mr 8

AC INPUT.

KE a”

3.00 — i 188 DIA. MTG. HOLES (16 PLACES)

CBB CASE UNIT WEIGHT: 8 ibs.

ASSEMBLY / OUTLINE & MOUNTING cBe-75w a ee 1235, ion

Page 31

C ¢C ( [Per oes [cs-67 0vP | CONDOR P/N DESCRIPTION ese TON ra

220/16 | 101 -10107. SAPACITOR, ALUM, ELECT. 3 TE000/15 ALUM: ELECT. : : 603/100. MYLAR cs ge 3 1750 ALUM.ELECT. 8 ge 8! Toor CAPACITOR, ALUMELECT : $3

  • RECT, 1A.,200V. 8 Rei REIC 1A.,200V. © M750 228, 50V. 2 ‘AEIC RECT, 1A. ,200V. 3 INTS2A, ZENER, 5.6% * ‘SO508LS3 ‘BA., SOV. TRECs [STR GARLINGTON, NPW 180] S]RESISTOR, Vw, 5% ,CF 4700. 1 47K i 22K 7 22K T ean] si03i3_ | 4 47a [1510333] 76K} 15210810 —[_1 Tew, ea] 158-1007? | 1 [aESISTOR,— aw 75540085) 15K [15510085 | 1" [POTENTIOMETER,2W, [ 130-10287_ 1 UaT23 13040287 UJi.C. VOLTAGE REGULATOR + 082-1061 1 i067 08241061 |] TRANSFORMER Tf oat SOs-110a1 | | [PRINTED CIRCUIT BOARD. B = ae a we eel CHASSIS Tee | aie 1008 [1 [enassis :

ola} |< —— res mc —$ tt ye} 13] 7 sial,|* 1c O-- Sighs 2-3 ont | |= cm ele § PRODUCTION NOTES: t le] TOW ee SE ATW TO SECURE Cine i, ‘ole .

ae ce Feat

ete G88 RE CORNECTION TABLE.

+ SENSE

—Sense

ant

Page 32

2800-0 FRONT PLATE EXPLODED VIEW 25¢ U.S. COIN

Index Part Index Part

No. No. Description No. No. Description

15301-1025¢ Coin Acceptor17 904599Coin Return Door
2400-4#4-40 Self Locking Nut18 404463Frontplate Assembly, 3-1/8" x 9-1/4”
3 404351Coin Inlet Chute Assembly19 404350Coin Return Chute Assembly
4110-4-64 x 3/8 Screw20 904936Keeper
5904717Lamp Socket21 905115Bar
6904716#47 Lamp (6.3 Volt)22 100-4-124-40 x 3/4 Screw
7904712Fastener23 404353Switch & Wire Assembly
8 904583-1Coin Return Lever24 900651Retainer
9 404464Inner Panei/Lever Assembly25 904710-1Switch Wire-Silver
10 404348Coin Return Button Assembly26 904845Switch
11 904591Coin Return Button27 100-6-46-32 x 3/16 Screw
12 90470325¢ Price Decal28 40435412 Volt Crem Assembly
13 904589-2Reject Cover Button (25¢)29 904762Switch Cover
14 345-4-5#4 x 5/16 Pan Head ScrewMOUNTING HARDWARE NOT INCLUDED IN KIT
15 904588Coin inlet Housing30 406-10#10-24 Hex Nut
16 904590Coin Return Cover31 905022#10-24 x 1-1/8 Carriage Bolt