CATHODE RAY TOMES

StarHawk

Starhawk (Cinematronics, 1979) · Document · 45 pages · 9 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

STARHAWK SERVICE

AND

OWNER’S MANUAL

CINEMATRONICS, INC. 1841 FRIENDSHIP DRIVE EL CAJON, CA 92020 (714) 562-7000

TELEX: CINEMAT 697891

CALL TOLL FREE: 800 854-6577

IN CALIFORNIA CALL: 714-562-7000

SALES: 8-5 (PST) WEEKDAYS

SERVICE: 8-5 (PST) WEEKDAYS

© COPYRIGHT 1979

ALL RIGHTS RESERVED

Page 3

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 4

CHAPTER

1.

2.

3.

Ae

10,

ll.

12.

13,

14.

15.

16,

17,

18. CONTENTS

COMEENES srseeereserecee

IMCroduction .esseeesscesseseesersccrseeee

Warranty cecsecccssreccssercuscccracseeere

General Information ....ssesescscceesesces

Vector Theory .srerecrerccesccseccsesveces

CPU Board ..sessecevscccsorcserevresseseee

Block No's. and Component 1.C.'S ..seseees

CPU Block Diagram ...cecsceseeeeesesssocee

CPU Diagram sesscsccceccsccccsevevsasonses

Audio Board ...ssseesessees

Vectorbeam Monitor Operation ..sesseeeeeee

Trouble Shooting Hints ....seeeeeee

Trouble Shooting Flow Chart .....seesee

Suggested Stock Parts ..

Logic Board Schematics .....cssssseereveee

Display Board Schematics .....-+.seveeeees

Audio Board Schematic .esersceseereccceese

Power Supply Schematic .icsecrecvseecoeres lL

a1

Page 5

Dear Service Department:

With Starhawk going out the door, I feel it’s a good time to review the procedures for ordering and returning parts.

Starhawk will have a 90 day warranty, which means that the attached page should be followed carefully, to help process your orders as quickly and effeciently as possible.

There are several points which need to be stressed regarding these procedures:

  • When placing or returning an order, please be sure to use a purchase order or RMA number. This helps us to reference your order properly, and insures proper credit.
  • Please have the game serial number ready when you place your orders. ORDERS FOR STARHAWK WILL NOT BE ACCEPTED WITHOUT IT?
  • Advance replacements become the property of the customer after 30 days if the part has not been returned, (Over-seas shipments are allowed 60 days). Applicable charges will be applied after this time.

Our invoices are designed to minimize paper work for both ourselves and also for you. The invoice, return authorization, and credit memo all refer to the same six digit number.

Looking forward to working with you!

Ze Ste TF

Nancy Olson Customer Relations

Page 6

WARRANTY FOR STARHAWK

Cinematronics, Inc. warrants the goods to be free from defects in materials and workmanship under normal use and service for a period of ninety (90) days from the date of delivery on all parts except switches, potentiometers, buttons, fuses and lights, for which the warranty period is thirty (30) days from the date of delivery. Cinematronics makes no representation or warranties concerning the goods whether express or implied by operation of law or otherwise, including those of merchantability or fitness by operation of law or otherwise, including those of merchantability or fitness for any particular purpose, or with respect of patent infringement, except as may be specifically made herein, to the repair or replacement of such parts which have been returned to Cinematronics plant at purchaser's expense and which examination shall disclose to Cinematronics satisfaction to have been so defective and to be the shipment of such repaired or replacement parts to the purchaser F.0.B. the shipper point.

This warranty does not apply to any Cinematronics product which has been altered or repaired by unauthorized personnel or service facilities or any products which have had the unit serial number altered or removed.

Upon acceptance of the goods, the purchaser agrees to assume all liabilities for damage and/or bodily injury by the purchaser or any other claims arising from the use or service of the goods by any person, Purchaser further agrees to idemnify Cinematronics, Inc. from any liability, claim, cause of action or litigation resulting from the use or misuse of the goods by any person.

Page 7

GENERAL INFORMATION

Generally speaking, your Starhawk game is designed much the same

as conventional video games. The only major exception to this is the

fact that the Starhawk game is provided with an alternate means of visual

display: the patented Vectorbeam tm monitoring system.

The game is, however, built of the same basic building blocks as

any other video game,

The Power Supply, which provides all necessary voltages to power

each separate electronics assembly as well as all lighting required

throughout the game. It must be noted that there are "on board" regulators

provided for certain voltages needed on both the audio logic board

and the display printed circuit board. The plus five (45) volts d.c.

regulated voltage for the central processing logic board (CPU) is

developed totally on the power supply. This same voltage is used where

needed on the audio logic board and also the display printed circuit board.

The Central Processing Unit, contains circuitry to strobe and interpret

all input functions including the player control panel switches and all

coin and credit information and to create all the digital signals used in

providing the visual display. It also contains all the software (i.e.,

machine language and game personality memory) needed to control the game

operation and to generate the proper vectors needed to display.

In fact, the CPU logic board contains a great portion of the vector

generating system, which also includes the display unit. The CPU logic

beard also controls the switching (electrically) of the audio printed

circuit board.

*Vectorbeam ©" is Cinematronic's service mark for video game repair and educational services.

Page 8

The Audio Board, as in many other video games, is comprised of a

noise generator and the associated wave shaping circuits as well as a

number of amplifier stages on command from the CPU logic board,

The Yectorbeam *™ * Display Electronics is the final form of

interpretation of the CPU's calculations. The CPU logic informs the

display electronics unit of information regarding line length and line

placement on the CRT. This is accomplished with two twelve-bit words,

one each for horizontal and vertical deflection, and a number of other

controlling signals for the cathode drive circuit and switching in the

delfection circuits.

The major difference between the vector generator and raster scan

type monitors is the means by which the cathode beam is directed (deflection)

across the screen.

In the raster scan types of display the electron beam from the’ cathode

to the anode of the CRT is constantly deflected (scanned) across the

face of the CRT is a series of horizontal lines that trace from the

upper portion of the screen to the bottom in a syncronous pattern.

Vertical information is added, also syncronous with the horizontal,

forming a matrix-type pattern of mathematically possible illumination

points on the CRT. If the cathode current is increased at these points

on the screen in matrix-type patterns (similar to placing dots on a piece

of graph paper where the lines intersect) coherent video in the form of

shapes and alpha-numerics to form the game backgrounds can be displayed.

The vector generator takes a slightly different approach to cathode

beam deflection. The results are a much higher degree of resolution and

much smoother motion across the screen, as well as the ability to draw true

Page 9

curved lines on the screen. Rather than using a constantly scanning cathode

beam, the beam is directed only to points of eventual illumination, using a

vectoring form of programming rather than a matrix approach. Basically, the

cathode beam is directed between two determined points, and illuminates

the entire path of phosphores between these two points, unless blanked by

stopping cathode current (i.e., when the beam moves from one star to

another on your screen). The ability to illuminate the entire path of phosphors

crossed by the electron beam, in any direction desired, (which is not

possible in a raster scan system) creates a much higher degree of resolution

than can be found in a raster scan system while at the same time creating

a much greater number of angle possibilities. This is also supported by

the ability to accomodate two twelve-bit words of information, twelve each

for vertical and horizontal deflection, and the fact that there is no

background illumination from a constantly scanning beam when brightness is

turned up, The higher degree of resolution combines with the totally

blackened background creating an appearance of depth not found in a raster

Scan system,

Another major design difference is the fact that no sync. signals are

needed to produce vectors on the CRT. This greatly simplifies the hardware

design of the system, and therefore the understanding of the theory of

operation, of the CPU logic as well as the display electronics,

Page 10

VECTOR THEORY

In order to understand the basic concept behind a vector

generated display, it is important to have a basic knowledge of vector

theory.

As mentioned in the general information section of this manual, the

raster scan display uses a matrix type display pattern.

representation of a matrix is shown below in Figure A.

VT

HORIZONTAL

[|

Lid L o

VERTICAL

For example, to produce a line on the CRT with a matrix-type pattern,

the appropriate intersection points of horizontal and vertical lines are

illuminated. The calculations which select these points are made on the

logic board, and converted into video information for the monitor to digest.

Although there are spaces between the illuminated points, the illusion of a

solid line is made by your eyes, and the resolution is determined by the number

of available horizontal and vertical lines in the system, and the speed of

the sweep. A graphical

Page 11

In the vector display system, there are no horizontal and vertical

lines (no sweep) or sync. a line created using a vector system as shown in

Figure B., below.

A Line is drawn by programming a beginning and ending point of the line

to be drawn, and forcing the cathode beam to travel between these two points,

illuminating the entire path of phosphorus on the CRT. The angle of the line,

the position of the line, and the length of the line are determined simultaneously,

and simply, by selecting the proper voltage levels for the beginning and ending

points of the line.

Page 12

This is accomplished by the two twelve-bit codes (words) applied

to the DAC-80's on the display board. The DAC-80 will produce a different

voltage level at its output for each possible combination of input levels

(of which there are 4128 possibilities for each 12 bit word.)

It is also important to remember the function of the LF 1331D (V-2)

analog switch and its output RC network (see monitor theory), Because we

are dealing with reactive components in C101 and C201 on the display board,

the charging voltages found are non-linear by nature, (See Figure C., below).

| BCH

dhadgt loldagd curva B dé dap citlor Co)

oltagi

: + [cunredt |

Therefore, when a line appears on the CRT, it is actually only part

(section A~B, Figure C) of the entire path taken between the beginning and

ending points of the vector (C-D). The section of A-B is chosen as the most

linear portion of the charge curve, and illuminated

Sections C-A and B-D are blanked at the cathode, and points A and B chosen

by coutrolling the analog switch (V-1) on the display board, Again, these

calculations are all performed on the CPU logic board,

Page 13

The end result of using the vector generator is an immensely increased

number of programable point, which is in direct proportion to the word size

and the capabilities of the DAC-80 (i.e., greater esolution, definition and

smoother motion using minimum of hardware).

10.

Page 14

CPU BOARD

The processor hardware can be broken down into five basic

functional blocks as shown in Figure 1, The arrows indicate the possible

data flow directions between the various blocks. The ALU and Control

block are the main components of the processor while the Memory and I/0

blocks may be thought of as merely peripherals, Figure 2 is a detailed

block diagram of the processor. The numbers in each block correspond to

the entires in Table 1, which lists the IC numbers of the main components

of each functional block.

The following is a brief description of each block shown in

Figure 1. The numbers beside each functional block name are the numbers

in Figure 2 which correspond to a particular function.

RAM (6)

The RAN is implemented with three 9101C read/write static memories

configured as a 256 x 12 bit block. Data can be transfered to or from this

memory via the ALU block. The processor uses this RAM as a scratch pad,

Bom (10) The ROM is configured as an 8k x 8 bit block of memory. These

memory locations contain the program instructions and/or data. It is accessed

via the precessor control unit,

10.19, 17, 18 The 1/0 block consists of & input lines implemented with a bit

addressable latch, 24 input lines implemented with data selectors, and two 12

bit registors which are connected to the X Y display deflection circuits via

D/A convertors,

nh.

Page 15

Arithmetic Unit 1,2,3,4,5

The arithmetic unit performs all the arithmetic processing for the

system. It consists primarily of two 12 bit accumulators, an arithmetic

logic unit and various data selectors. The accumulators can function as

temporary storage registers for arithmetic calculations, or as the source

and destination registers for I/0 operations. The ALU performs the actual

arithmetic functions upon the data in the accumulators. The data selectors

are used to select the various sources of data which will be processed.

Control Unit (15, 16, 14, 7, 8, 9, 11, 12, 13

The control unit is the heart of the processor. It performs

all instruction decoding operations and generates all the necessary control

signals which the rest of the hardware requires to function correctly,

The following is a discussion of each block shown in Figure 2.

  • Accumulator Selector

The accumulator selector consists of 3 quad data selectors.

They are used to select the output of either the primary or secondary accumulaotr

for processing by various other sections of the system.

  • & 3, Primary and Secondary Accumulators

The two 12 bit accumulators are implemented with quad bidirectional

shift registers. The primary accumulator consists of S4, P4, M4. The

secondary accumulator consists of T4, R4, N4, All data manipulation in the

processor is accomplished using these two accumulators. All output data flows

through these registers,

  • Arithmetic Logic Unit (ALU

The ALU is used to perform all necessary arithmetic functions within

the processor, The ALU is implemented using three 25LS181 (N6,M6,L6) function

12,

Page 16

generators, three 74LS85 (N9 M9, L9) 4 bit magnitude comparators, and a

748182 (14) look ahead carray generator. The data which the ALU manipulates

can come from four different sources. The first source is the contents of

the accumulators via the accumulator selector. The second and third sources

are the ROM and RAM data outputs via the ALU data selector (N11, M11, L11)

and the fourth source is the external input lines via the input selector

(E4, D4, C4).

>. Data Selector

The data selector is used to read data into the ALU from either

the RAM or ROM memory. Note that the ROM data is only 8 bits wide while the

RAM data is 12 bits wide,

  • RAM Storage

The system RAM consists of three 9101C high speed static memory

chips connected as a 256 x 12 bit block. The block is 12 bits wide in order

to allow the contents of an accumulator to be stored. The processor uses the

RAM as temporary storage of program variables, data pointers or any other data

of a dynamic nature.

  • RAM Address Selector/Register.

The output of this register is tied directly to the address lines

of the RAM. It consists of a multiplexer which routes address data from either

the ROM or RAM locations to the RAM address lines. The capability to use RAM

data to select RAM addresses is the basis for the indirect addressing mode of

the processor.

  • Page Selector

The page selector is used to latch the high order 4 bits of a RAM

address during some types of RAM access instructions.

13,

Page 17
  • ROM Data Register

This register is used to temporarily hold data from the ROM

during an instruction fetch.

  • ROM Memory

The ROM memory consists of the actual memory chips plus a data

selector and latch circuit. The latch is used to improve the memory access

time during a two byte instruction fetch by allowing one byte of the instruction

to be latched while the RAM address lines are decoded for the other byte,

The data selector can then be used to rapidly access both bytes of the instruction

b y switching between the latch and memory outputs.

ll, Instruction Register

The instruction register is a latch which holds the current op

code as read from the ROM. Its output is tied to the instruction decode circuitry

which in turn generates the necessary signals to execute the instruction.

12, System Sequencer

The system sequencer is used to decode an instruction op code

and to generate the appropriate timed sequence of signals which execute the

instruction. The op code is decoded by suing it as the address data to a set

of decoder ROMS. The outputs of the decoder ROMS are then synchronized with

the system clock and used to control the various system functional blocks,

  • Line Length Counter

The line length counter is used during the process of drawing a

vector to control the length of a vector, by turning off the beam at a pre-

determined time after the vector is initiated. The counter is loaded with a

value from a line length ROM and then counts up until it overflows which in

turn generates a signal to indicate the vector has been finished,

14.

Page 18
  • Program Address Selector

This selector is used to provide the address data to the program

ROM. It selects either the program address counter output or the accumulator

selector output and routes this data to the ROM address lines. The ability to

use the accumulator contents as address data allows the program to randomly

access data tables stored in the ROM or to compute a branch address after a

conditional test.

  • Program Address Counter

This is a 12 bit counter whose output defines the next location

in ROM to be accessed. It is normally clocked sequentially to step through a

program. However, it can be loaded with data from the program address register

which is how the jump instructions are implemented.

  • Program Address-Register

This register is a latch used for temporary storage of an address

which will be loaded into the program counter during a jump instruction. The

input data to this latch can come from either the program ROM or the scratch-

pad RAM.

  • Input Selector

The input selector is used to read the state of one of the 24 input

lines into the selected accumlator. There are 16 primary inputs and 8 secondary

inputs. During an input instruction the upper 11 bits of the accumulator are

set to zero while the least significant bit reflects the state of the input line.

All input lines have pull up resistors on them so that they will read high if they

are left unconnected.

15.

Page 19
  • Output Selector

The output selector is a bit addressable latch used to

control the 8 output lines, During an output instruction the selected output

line is set to the complement of the least significant bit of the

accumulator. The output lines are used to control the audio board, display

intens ty and the mechanical coin counter.

  • Display Registers

The display registers are the interface between the

processor and the display driver circuits, These registers are latches

into which the contents of the accumulators can be stored. The outputs

are tied to D/A converters which provide the input voltage to the display

deflection amplifiers.

16.

Page 20

1.

12,

13,

14.

15.

16.

17,

18.

19. BLOCK NUMBERS AND COMPONENT I.C.'S

T-2, R-2, N-2

$-4,P-4, M4

T-4, R-4, N-4

N-6, M-6, L-6, N-9, M-9, L-9

N-11, M-11, L-1t

N-14, M-14, L-14

J-12, 1-12

U-7, R-7, T-7, P-7, U-9, T-9, U-11, T-11

T-13

A-B, G-10, F-10, G-14, F-14, E-14, D-14, C-14

E-6, D-6, C-6, E-8, H-8, G-8, F-8

S-9, R-9, P-9

S-11, R-1l, P-11

P-13, R-13

E-4, D-4, 0-4

F-2

S-2, P-2, M-2

17.

Page 21

BRUNING 40-21 40423 PROPRIETARY THIS DOCUMENT 1S THE PROPERTY OF CINEMATRONICS INC. AND IS NOT TO BE REPRODUCED OR DISTRIBUTED WITHOUT WRITTEN AUTHORIZATION OF CINEMATRONICS INC.

PRIMARY, [xecuw @

| SELECTOR T SECONDARY

STORAGE

Page 22

[revisions id rev] vescurion [DATE | AreROWED

SANG AEE CINEMATRONICS [Cm rnovecr enon: [pare RELEASE APPRov|DATE| DWG TITLE

BLOCK DIAGRAM

[DO NOT SCALE DwGIC PU BOARD - DETAILED TOLERANCE: UNLESS PaaS FRET Focoo SIZE PROJECTION: ]SCALE: ws B BD 201000 => -@-|NONE [oon wens] sweet Cor FINISH: BREAK ALL SHARP EOGES AND OEBURR ALL HOLES.

Page 23

BRUNING 40-21 40423

UNIT

ARITHMETI CONTROL

FEB 28 joe"

WN BY: D El Cajon ae ERS CINEMATRONICS [Noma DWG TITLE FIM ue snare | eUEASE APPROMIPATEL BOCK = DIAGRAM

EDGES AND DEBURR CPU BOARD

TOLERANCE: UNLESS OTHERWISE SPECIFIED [MODEL NO.| DWG JDWG NO. “A | BD201I000 PROJECTION: [SCALE: =3 ~@-|NONE [eove sent. SHEET] OF

Page 24

STARHAWK AUDIO BOARD

The Starhawk audio board is a self-contained electronic sound

generation system that requires connections only to external power,

control, and loudspeaker connections. Sounds generated include a

simulated explosion, laser firing sound, and a special FMed waveform

used in association with the killer ship.

The circuit incorporates a master on/off control, pin 15 of the

control connector. When this pin is at a high level, the board is

disabled and no audio is produced. When this pin is at a low level,

the board is enabled and can produce under digital control, any or all

of the sounds listed above. In addition, anytime that the board is

enabled it produces a low level background noise.

The laser firing sounds are produced by two completely independent

circuits so that either or both channels may be active at any time. The

channels, pins 12 and 13, are turned on by a high input level and will

produce sound continuously so long as the input remains high, The sound

produced starts at a high pitch and decreases in frequency with time until

it stabilizes at a very low frequency, Time constants in this circuit have

been chosen for best performance with a one second duration control signal.

When the control signal returns to a low level, the circuit resets within

150 microseconds and is then ready to be retriggered.

The explosion sound consists of digitally synthosized noise with a

large amount of low frequency power. The explosion is triggered by a low-

going pulse on Pin 11.

21.

Page 25

Triggering will occur on pulse durations as short as 100ns, but is

designed to be done by pulses of 400ns or more, Maximum trigger pulse

length should be limited to approximately 30ms, since the logic may

start timing the duration of the explosion from the end of the trigger

signal, rather than the start (this is a characteristic of the 556 IC used). The killer ship sound has two control lines, pins 14 and 16. Pin

14 is the on/off control (high level off). This sound is intended to

be used by setting Pin 16 high, waiting one second, and then setting both

pins low, This creates a warbling sound that starts at a low pitch,

ramps up to a high pitch before turning off.

THEORY OF OPERATION

Output Amplifier

The audio power output amplifier uses a conventional operational

amplifier (op amp), with a current booster connected to its output, The

circuit is connected as an inverting amplifier with variable gain obtained

by the use of a variable resistor in the feedback path. The input to

the circuit is coupled through an electronic switch which serves as the

master on/off control, The maximum possible output level is limited to

approximately plus or minus 12 volts by saturation in the op amp's output

stages. For best results, the volume control should be set below the

point where saturation occurs. The circuit can drive an & ohm loudspeaker

to approximately 8 watts RMS power.

Laser Firing Sound

The laser firing sound generators each use identical circuitry. Four

basic elements are used in each channel: a voltage controlled oscillator

(VCO), a binary counter, a read only memory (ROM), and a digital to analog

converter, (DAC). Two logic inverters are used to enable/disable the channel,

22.

Page 26

and to generate the control voltage for the VCO.

In standby, the control input level is low, forcing the first

inverter's output high which both disables the ROM through it's chipselect

input and also causes the second inverter's output to pull low, which

discharges the capacitor connected to it. Since the ROM is disabled, it

produces no output to the DAC, which produces no signal to the audio

output stage. The VCO will be operating at maximum frequency because

its control voltage is minimum. (see below for detailed VCO operation

description).

When the laser firing sound is enabled, the ROM's chip enable

is activated, allowing it to produce a binary output signal. This signal

is connected directly to the DAC (the 4 resistors), which converts the

binary data on it's input to an analog signal level at its output (the

junction of all the resistors). Simultaneously, the output of the

second inverter goes high (open), removing the short across the capacitor.

The capacitor will now be slowly charged in a positive direction, a little

bit of charge being accumulated on each positive cycle of the oscillator's

output, As the voltage on this capacitor rises, the Frequency of the

oscillator decreases, reducing the pitch of the generated sound,

The oscillator's output signal is buffered by a transistor and an

inverter, and is then applied to the input of a 7 stage binary counter.

The binary counter presents its output directly to the ROM, which converts

each of the 128 possible counter states to a particular data output

corresponding to each state. The data stored in the ROM produces a rough

waveform with much harmonic content, well suited to the generation of the

"mechanical" sound.

23.

Page 27

The data output from the ROM is converted to an analog voltage

level by the 4 resistors (the DAC) connected to its outputs. This analog

voltage level, a complex waveform, is then amplified by the output amplifier

and delivered to the loudspeaker.

ae)

The operation of the VCO depends entirely on the characteristics

of the op amp when it is overdriven. Consider the circuits consisting only

of the op amp, the two resistors from its output to its inputs, the two

diodes, and the capacitor connected from the negative input to ground.

Assume that the negative input is at 0 volts, and that the positive input

is at +.7 volts, and that the control voltage (on the cathode of the diode)

is 0 volts. The amplifier see +.7 volts input differential, which drives

it to positive saturation at its output, approximately +12 volts. This output

voltage is fed back to the positive input through the resistor, but is

clamped to .7 volts by the diode connected to the control voltage.

Simultaneously, the capacitor connected to the negative input is charging

toward +12 volts through its feedback resistor. This situation persists

until the voltage at the negative input rises above +.7 volts, at which

time the differential input to the op amp becomes a small negative value,

cuasing tits output to saturate in the negative direction to approximately

-12 volts. When this occurs, the voltage on the positive input becomes

-.7 volts (limited by the diode whose anode is grounded). The op amp is

now heavily saturated, and will remain so until the capacitor charges from

it's +.7 volts level to -.7 volts. At this time, the op amp repeats

indefinitely, producing an output AC signal. The period of the oscillation

is determined by the time required for the capacitor to charge from +.7 volts

24.

Page 28

to .-7 volts, and by the time required for the capacitor to charge from 7.7

volts to+.7 volts. This time is a function of the size of the resistor,

the value of the capacitor and the saturation voltage of the op amp, all

of which are approximately constant.

Assume now that the control voltage input connected to the cathode

of the diode is 5 volts, rather than 0 volts. The operation of the circuit

is now altered so that the capacitor must charge from -.7 to +5.7 volts, and

vice versa. Since no other factors have changed, the time required to

charge and discharge the capacitor has increased, thus decreasing the

frequency of oscillation.

The signal at the op amp's output is a rectangular wave with levels

of approximately plus or minus 12 volts and moderate rise time. This

signal is converted to TTL level, and the rise time improved, by the

transistor driven from the op amp's output. The resistor attenuator

feeding the transistor protects the emitter-base junction from excessive

reverse bias, while the inverter following the transistor still further

improves the rise time.

Killer Ship Sound

The killer ship sound channel consists of control logic, a low

frequency oscillator for warble control, a ramp generator, a VCO, an analog s

switch, and a buffer amplifier. The control logic is fairly complex, due

to the requirement for both an “enter” sound and an “exit' sound,

The on/off control signal (pin 14 ) performs two functions: it

enables output from the buffer amplifier, and it starts the ramping of the

control voltage, The control voltage (at the 1 microfarad capacitor) is at

approximately +9.5 volts before the channel is turned on. This voltage is

primarily determined by the 510K and 1 meg resistor voltage divider, working

25,

Page 29

into a virtual ground at the input of the first inverting op amp. The

output of this op amp is always equal to the input, but opposite in polarity.

Thus, the output of the first inverting op amp is approximately -9.5 volts

before the channel is turned on. The second inverting op amp re-inverts

the voltage back to +9.5 volts, and makes it available at high current

to the other circuitry.

When the on/off control signal is set low (on), the control voltage

begins to drop twoard ground. The 1 meg resistor and 1 microfarad capacitor

determine the rate of charge of this voltage. When the voltage reaches 4.5

volts, it cannot drop any further due to the +5 volts applied through the lk

resistor and diode to the control voltage point, until the enter/exit line

is brought high. With this line high, the 4.5 volt clamp is no longer

enabled, and the control voltage can discharge to 0, still being timed by

the same resistor and capacitor.

Since the two inverting op amp circuits each have a gain of minus

1, their two outputs are always equal and opposite in polarity. The initial

voltages of -9,5 and +9.5 will ramp down to -4.5 and +4.5 when the channel

is enabled, and then down to near zero (minus and plus), as the exit control

is applied. These voltages are fed to the control inputs of a VCO

(nearly identical to the laser firing VCO's), the output of which ramps

upward in frequency as a function of the decrease in the magnitudes of the

control voltage.

26,

Page 30

VECTORBEAM MONITOR OPERATION

The vectorbeam monitor can be divided into two basic sections.

One section is the deflection amplifiers, and the other section is the high

voltage and cathode drive circuit.

The deflection amplifier can be further divided into two indentical

channels: one for vertical deflection, and one for horizontal deflection. We

will describe the operation of only one channel (vertical) and the same theory

of operation will also hold true for the horizontal section.

Digital information, in the form of a twelve-bit word, is applied to

the input of the DAC-80 digital to analog converter (U101) on pins one throvgh

twelve, The most significant bit (MSB) is applied to pin one, and the least

significant bit is applied to pin twelve. The DAC-80 makes the necessary

c onversion from digital signals to analog signals which are outputted as

analog voltage signals on Pin fifteen (which is proportional in level depending

on the input word applied). The result is a positive and negative voltage signal

about its reference voltage (remember, there is no "sync" signal present, and

the signal is not true video as seen in raster scan monitors).

From the DAC-80 the analog signal is then sent to a high-speed analog

switch, (U1). The analog switch has two parallel inputs for the display signal,

and two controlling inputs which select one of two outputs from the switch,

At the outputs is found an R.C. network, which is used to create line length

and line position on the screen.

Output fifteen from the switch routes the analog signal through a 5K

potentiometer (R102), an 11k resistor, (R103) and to the input of U102 op-amp.

The time constant developed by these two resistors and the capacitor (C101)

determine the length of the vector line seen on the screen. Adjusting of the

potentiometer will adjust the length of the vertical Iines seen on the screen,

27.

Page 31

Output ten from the analog switch routes the signal directly to the

input of U102 op-amp, and the resulting time constant of the op-amp input

impedence and the capacitor C101 determines the position on the screen of the

vector line.

Op Amp, U102, serves a dual purpose: one, it acts as a buffer between

the deflection amplifiers and the analog switch; and two, it acts as an "edge

gain" amplifier (i.e., height).

At the output of U102, there is a resistor amp, diode network consisting

of R105-R110, and CR101 - CR104, This resistor diode network is used to compensate

for the non-linear characteristics of the CRT near the edges of the screen, If

this circuit were not used, any object displayed on the screen would increase

in size as it moved closed to the edges of the screen. Also contained in the

circuit is a potentiometer (R109), which adjust the height of the pictures.

From the wiper of R109, the signal proceeds to Q101, which is the first

stage of deflection amplification. Q103 is an emitter coupled with Q101 to

provide a degenerative feedback loop from the yoke. Q102 is used to provide a constant current source to both emitters.

At this point, the deflection circuit can again be divided into two

identical circuits, One circuit, which controls the lower half of the screen,

is comprised of Q104, Q106, Q108, and Q110. The other circuit, which controls

the upper half of the screen is comprised of Q105, Q107, Q109, and Qill. **

Q104, Q108 and Q110 are three stages of amplification, while Q106 is

used as current limiting protection for Q108 and Q110. The same holds true

for the other configuration of Q105, Q107, Q109 and Q111. R124 through R129 are

used as a current divider network for the yoke.

*k In the horizontal section of the deflection amplifier, Q204, Q206, Q208, and

Q210 control the left hand side of the screen, and Q205, Q207, Q209, and Q211 control

the right hand side of the screen. By dividing the screen in this manner, four

quadrants of deflection area have been developed (see vector theory chapter.)

28.

Page 32

R122, R123, and C102 form a RC network, which compensates for any CEMF

that may develop by the expanding and collapsing of the deflection coil's electro-

magnetic field.

The high voltage and cathode circuitry is the second section of the monitor.

Thig section also contains the necessary voltage regulation to power the IC's located

on the display board as well as develop the high voltage.

U4 and U6 provide plus 15V and minus 15V respectively to power the DAC-80's

and the TLO81 op-amps on the display board,

U3 and U5 provide plus 18V and minus 18V used in the high voltage transformer

(T-1) and oscillator (the oscillator circuit is necessary because there is no

horizontal syne. used to develop the high voltage pulses.) The oscillator circuit

is comprised of primary windings, Q4 and associated discreet components.

The high voltage 18KV is developed by Tl secondary windings, the high

voltage tripler, and the focus circuitry. The potentiometer, R16, is used to adjust

the focus of the cathode beam,

One of the secondary windings of Tl develops the necessary cathode voltage,

which when measured at the cathode of CR6 should read 88VDC, The cathode circuitry

in the vectorbeam * ™ monitor is comprised of U7, a 7406 IC used for buffering logic

signals which control brightness and blanking. It also contains the transistors, Ql,

and Q2, and Q3, and then associated discreet components.

Ql, and the first gate of U7 control the brightness of the cathode signals

upon command of the CPU logic board. Q3 and the second gate of U7 control: the

intensity (blanking) of the cathode signals, also upon command of the CPU board,

Q2 is used as a power failure protection for the cathode circuit in the event of

a loss of 25V power supply voltage, This protection aids in avoiding phosphor

burning on the CRT, R111 is the brightness potentiometer, which adjusts the

amplitude of the negative spikes used for brightness and intensification.

29,

Page 33

TROUBLE SHOOTING HINTS

Read carefully before servicing game, Because of a number of design criteria in your Space Wars game, a problem that arises will generally cause one or both of the twenty five (25) volt fuses or breakers in the power supply to blow. When this occurs, the following procedures will aid in locating the fault assembly, It is important that this procedure be followed in the order in which it is written!

  • Unplug the game and short or meter the two filter capacitors found in the power supply. These are the two 20,000 micro-fared capacitors mounted near the transformer. They will maintain a charge when the fuse(s) are blown.

2, Replace the fuse(s) with MDL-3 Fuses.

  • Disconnect the Molex plug and the ribbon connector from the monitor.

4, Plug in the game again and observe the fuses.

5, If the fuses remain in tact, place a credit on the game.

  • Start a game as if you were going to play, and listen for the game sounds,
  • If the sounds of the game (acceleration and fire) are present, the problem is in the monitor. If the sounds are not present, or if they are distorted, the problem generally is in the CPU logic board.

The reasoning behind this procedure is that if a failure occurs, in the CPU logic board, it will enter a "constant reset" mode. When the CPU logic board is in this mode of operation, or when there is a lack of computer information at the monitor input (i.e., disconnected a faulty ribbon cable), the monitor will automatically deflect the electron beam off the screen to protect the phosphors in the CRT. When this occurs, the monitor deflection amplifiers will enter a current limiting state and eventually cause the fuses to blow.

For further troubleshooting procedures, use the flow chart provided.

NOTE: It is important to follow steps one and two every time a fuse blows, to protect yourself from electrical shock, and also to protect the game from further damage.

30.

Page 34

TROUBLE SHOOTING FLOW CHART

Replace

Fuses

Unplug Monitor

Replace Fuses Unplug Audio board Fuses Blown? Repair or Replace Audio Board Plug in Game

Fuses Blown?

Replace Fuses Replace or Unplug CPU logic Repair Fuses Blown CPU logic Monitor +5VDC on CPU board +5VDC? Place Credit on Game Accept Credit?

Start Game Replace or Game Sounds? Repair Power supply

Replace or Disconnect CPU Logic Monitor & &SVDC +SDVC? Repair Monitor

31.

Page 35

SUGGESTED PARTS FOR STOCK

Due to the fact that the vectorbeam *™ system is a new type of display

technology, there are a number of components used which may have limited

availability from your local parts suppliers. It is suggested that the following

list of parts be purchased from Cinematronics in the event servicing of your game

becomes necessary:

1, TL182 - Analog Switch

2, TLO81 - Op Amp

3, 7918 - Regulator IC

4, 7915 - Regulator IC

  • 7818 ~- Regulator IC
  • 7815 - Regulator IC
  • LF 1331D - High speed analog switch
  • DAC-80 Digital to Analog Convertor **
  • 74LS259 - IC (Texas Instruments only)
  • 74LS32 - Ic
  • Set D-ROMS (1-6)

12, Masked ROMS

Note: Contact factory for current prices

32.

Page 36

Passes

aaa vay ae eae]

SS ——— STRODE oi

» u ww ano va T4suy at ae

ic

a)

Tan an ae

Takes

res o Ce

3 Tatas fac

€1

weiss s = ie 1 sracee Your Ds - STROBE voer

nn o "hs ray ‘ THLSISE — | ly

,

oe 6 Aprende Lr Lor LP te

paisier pease

aL . a2

®

| fanaa’

7m FLIP Por ane TaLs107 RESISTOR TO +S

notes a ee es cet oa nis

ava

covaren

a0

atv _vartigy

Iiweer sor 2eve SHEET Lory

Page 37

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 38

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 39

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 40

Pay

Say TAL gea re cnr

Phe

say

NORMAL RE VECTOR

putAL PesiTign one

LINE DONE: ser yaawine,

one tines

TERT,

tom then)

an inves

Ae

TaLsied mb cae FHL 3194 ase Gta

Mares 65 har ao PEA Tie ete

rrr

Pas |Pte_|9ay fhm Say 340

  • | Hy reer 2 aa sae Pains “lr Shy | $A, | She nla be Le be le I is is a or a ay THAT 5-9 Pee ee ee ee Ta saTT THLSSTT MAR

Gay or ae ay aT Cine [a as rama

bowery

aed a4 la le le le an se Hs bx eo 7 9 en be dudu oe is la le |= je [es

OK 3 7 2

Page 41

CINEMA] onic, INC. Previn: DISPLAY poRCTREWIES SCHEMATIC

Page 42

ALL CAPACITOR VALUES ARE IR MICROFARADS,

ALL AEIETOR VALUES ARE 1m OHMS ENCES OTHE A WISE NOTED WoTe: @ Arts TRY AIRG AND AZZ62AU REZ ARE COMPSED OF

SiC ETA |W AEMSTORS © THESE POWER TRANSISTORS BRE movuTTO ow near SIRS BND ARE SEPRATS TROM THe Te, BeARO (DMs. NOEL) @ THESE ARE s6LDER ConMsCTION PoINTs OW THE F.C. 9OARD

+5v[ >t D> 7805 E> +5 wits =r st [* = [*" Wesceecccomecrons PINT FUNCTION FILAMENT.

From 2 rims

Page 43

a = COT 2 eren GNM avIS) CavOg O1GNY DuPWINIG| T

  • a oe SSINOSISWSNID

Peaet etanaane si ATU aiE 1 963 OTR

Page 44

PART OF uh

ae a ee MOLEX 03-09-2128

a1 2NGO55 A2921- B02

~ 7

03-08-2041 +5V RTM | ten» ©)| F.w.RecT oc I i} yr2sy 3a

UNRES

tasvatm 1)! 6.3vac non 0.454

-HOOVAC _ U1 5VAC. [2]Rtcommenoro Fusing; 34 SLO BLO FOR 115¥. 1.54 SLO BLO FOR 230¥ ms 1 [i] PansroRWCA SHOWN WIRED FOR IISVAC OPERATION a (eal RONICS sent 153279.

Page 45

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.