CATHODE RAY TOMES

Solar Warrior

Xain'd Sleena (World) (Technos Japan (Taito license), 1986) · Manual · 6 pages · 5 sections · original scan

Page 1

By Erik Sommerdyk

My comments are in green.

MANUAL

(PAGE 1)

IMPORTANT

FCC.

WARNING

THIS KIT IS INTENDED FOR USE ONLY ON COIN OPERATED VIDEO GAMES MANUFACTURED AFTER OCT. 1, 1983, AND ARE VERIFIED TO COMPLY WITH THE REQUIREMENTS IN PART 15 OF THE FCC RULES FOR CLASS A COMPUTING DEVICED. IMPROPER CONNECTION OF THE KIT, OF CONNECTION TO ANY OTHER OPERATED VIDEO GAME NO SO MANUFACTURED, OR VERIFIED FOR COMPLIANCE, MAY CAUSE UNACCEPTABLE INTERFERENCE TO RADIO AND T.V. RECEPTION: THUS REQUIRING THE OPERATOR TO MAKE THE NECESSARY CHANGES TO CORRECT THE INTERFERENCE.

MEMETRON, INC. ASSUMES NO RESPONSIBILITY FOR KITS IMPROPERLY CONNECTED TO GAMES FOR WHICH USE IS NOT INTENDED.

MAKE SURE YOUR POWER SUPPLY PROVIDES THESE DC VOLTAGES: +5 D.C. AT 7A, +12 D.C. AT 1A & -5 D.C. VOLTS.

Pac-man, Ms Pac-man, Galaxian and other select games DO NOT provide a D.C. power supply. MEMETRON will not assume responsibility for p.c. boards returned with damage caused by the introduction of improper voltages.

Pac-man, Ms Pac-man, and Galaxian are the trademarks of Bally Midway.

(PAGE 2)

KING Kt CONTENTS

SOLAR WARRIOR P.C. BOARD

INSTRUCTION MANUAL

CRT PLEXI

MARQUEE PLEXI

ayopdshmleics) (ij) = 8 WAY WICO RED BALL STICK

CONTROL PANEL OVERLAY

CONTROL PANEL DECALS

INSTRUCTION DECALS

Mag Be (es F NIN t STANDARD GAMMA HARNESS:

Page 2

F.C.C CAGE

CONTROL PANEL BUTTONS

Contact your Memetron distributor for replacement parts.

SOLAR WARRIOR CONVERTS ANY RA s co OR STER SCAN MONITOR

TH av OR CAN BE MOUNTED

HORIZONTALLY L A I

NOTICE

Parts salvaged from your old game are required to complete your kit. |These salvaged parts must operate perfectly for the converted game to perform properly and safely.

MAKE SURE YOUR POWER SUPPLY AND MONITOR ARE WORKING PROPERLY BEFORE ATTEMPTING CONVERSION!

(PAGE 3) CABINET

Reconditioning the cabinet is one of the most important things that you must do. Remove all old graphics and artwork for the cabinet. Clean the cabinet, and paint if neccesary. Remember... A new game promoted player interest. This conversion is a new game....MAKE SURE IT LOOKS LIKE ONE!

CONTROL PANEL

  • Remove the old buttons, joystick and control panel overlay (note... do not throw out parts, certain items are required to complete your new control panel.)
  • Refer to suggested control panel layout. (below.)
  • Drill any new holes that are neccesary.
  • Plug and holes that will not be used, a common outo body bondo is probably the quickest filler available.
  • Carefully apply the new control panel overlay. Avoid getting air bubbles under the vinyl.
  • Once the overlay is in place, use an exacto knife to cut out the button and joystick holes.
  • Place the new buttons, joystick and instruction decals on the control panel.

SUGGESTED CONTROL PANEL FOR SOLAR WARRIOR

(PAGE 4) GRE AND MARQUEE PLE x I (wear protective eyewear while cutting plexis)

  • The marquee and crt plexi must be cut to fit your game. Do not remove paper mask until this is done.
Page 3
  • Remove old marquee and crt plexi from game.
  • Use these to measure and mark the new plexi for cutting.
  • The plexis can be cut the same way you cut tile or window glass. We suggest using a scribing knife. Using a straight edge to guide the knife, draw the scriber several times along the edge. Make sure your cuts go from end to end cleanly.
  • Lay the plexi on a table with the scribe mark hanging over the edge. While clamping the plexi to the table, apply sharp downward pressure to the otherside. Sandpaper should remove any rough edges.

GROUNDING

TO ASSURE PROPER GAME OPERATION AND TO PREVENT SHOCK HAZARD, MAKE SURE GAME IS PERPERLY GROUNDED. DO NOT USE A "CHEATER" PLUG TO DEFEAT THE GROUNDING PIN ON THE POWER CORD!

NOTICE

For safety and reliability, Memetron, Inc. doen not recomment or authorize any substitute parts or modifications of Memetron equipment.

Use of non Memetron parts and modifications of circuitry may adversely affect game performance.

Substitute parts of equipment modification may void FCC type acceptance.

Since this game is protected by federal copyright, trademark and patent laws, unauthorized game conversions may be illegal under federal law.

This "conversion" principal also applies to unauthorized facsimilies of Memetron, Inc., equipment logos, designs, publications, assemblies and games (or features not deemed to be in the public domain), wether manufactured with Memetron components or not.

(PAGE 5) cOIN COUNTER

To properly connect a coin counter on Solar Warrior you will need the following items.

  • 12 vold coin counter (1)
  • 1N 4004 diode (1)

(see diagram below)

  • Connect the coin counter wire from the P.C. board to the anode side of the 1N 4004 diode, then connect to one lead of the coin counter.
  • Connect the other lead of the coin counter to the cathode of the diode, then connect to 12 vold D.C. on your power supply.
  • MAKE SURE THE DIODE IS IN PLACE AND HOOKED UP CORRECTLY OR DAMAGE TO HE P.C. BOARD MAY OCCUR.

IF YOU HAVE ANY QUESTIONS CONTACT YOUR MEMETRON SERVICE REPRESENTATIVE ~ [DISTRIBUTOR NUMBER REMOVED] ~

(PAGE 6) DIP SWITCH SETTINGS DIP SWITCH 1

7 8 Coin -A |——} 1 Coin - 1 Play ON | OFF 1 Coin - 2 Play |OFF ON 1 Coin - 3 Play

Page 4

2 Coin - 1 Play Sound for Demonstration

ee Continue Mode

ON” po Sereen orentation | Po PR Norma

(PAGE 7)

DIP SWITCH SETTINGS DIP SWITCH 2

yf 8

OFF | OFF ON | OFF OFF | ON ON | ON

OFF | ORE ON OFF OFF ON

ON ON

OFF | OFF ON | OFF OFF | ON ON | ON

ORE] ORE ON | OFF OFF | ON Degree of Difficulty Eas

WA Most Difficult Game Time Normal

\/ Fast Bonus Score 20,000-70,000 Every 70,000 30,000-80,000 Every 80,000 20,000-80,000 Only 30,000-80,000 Only Number of Lives 2)

ON | ON Free Play

(PAGE 8)

MAIN HARNESS PIN OUT CONNECTION PARTS SIDE

SIGNAL NAME

GROUND GROUND +5V D.C. REGULATED +5V D.C. REGULATED -5V D.C. REGULATED +12V D.C. REGULATED

NOT USED COIN COUNTER 1

NOT USED COLOR

BLACK BLACK PIN NUMBER

BLUE-RED

VIOLET NOT USED VIDEO RED

VIDEO BLUE GROUND NOT USED COIN 1

1P START 1P UP 1P DOWN 1P LEFT 1P RIGHT 1P SHOOT BLUE BLACK

BLUE-GRAY

Q K ella iced ued iedlited @0/ 00| a0} 00/ 00) co

GRAY-YELLOW BROWN

BROWN-WHITE BLUE-YELLOW BLUE-GREEN a

v2

18}

diy/

19:

Ez

N

Page 5

NOT USED

NOT USED

NOT USED

NOT USED

NOT USED

(PAGE 9)

MAIN HARNESS PIN OUT CONNECTION SOLDER SIDE

PIN NUMBER SIGNAL NAME

A GROUND

NOT USED

NOT USED

NOT USED

NOT USED

NOT USED

NOT USED

NOT USED

NOT USED

NOT USED

SPEAKER VIOLET-WHITE

NOT USED

VIDEO GREEN GREEN

NEGATIVE COMPOSITE SYNC WHITE

SERVICE YELLOW-RED

NOT USED COIN SWITCH 2 RED-BLACK G/B) MQ) ay) 2) S/F) RG) a a) Boal

2P START ORANGE-WHITE

FOR COCKTAIL TABLE ONLY 2P UP

2P DOWN BLACK-ORANGE

BLACK-RED 2P LEFT BLACK-BROWN

2P RIGHT BLACK-WHITE

2P SHOOT BLACK-YELLOW 2P JUMP BLACK-GREEN

NOT USED

NOT USED

NOT USED

NOT USED ml b|5 8) B/B)s <|*) =| <

NOT USED

BOARD SET PICTURES

Page 6

Please Note: The contents of this file are copyrighted by and are the property of Erik Sommerdyk. You must have my authorization of you try to use this on your site. If you have anything that you would like added to this page or would like to use this info on your own page please email me to somerdyk@mns et