CATHODE RAY TOMES

Tokyo Wars Sitdown

Tokyo Wars SD (Namco, 1997) · Document · 41 pages · 15 sections · original scan

Page 1

Z6000S06 “ON Hed “AlaSIOdYd GAMOTIOS AYV TWANV SIHL NI LNO 13S STIVLAG SHL LWHL SALLVYAdWI SI LI GNV ‘SSWIL TV Lv ALSAVS YAWOLSND NIVLNIVW OL HOLVHAdO SHL AO ALITIGISNOdSSY SH SI 1] enue sio7es08dO QS SHYVM OAMOL OIWPCU

Page 2

namcco

NAMCO EUROPE LIMITED Namco House, Acton Park Estate, Tel. 0181 324 6000 The Vale, London W3 7QE, UK Fax. 0181 324 6010

EC Declaration of Conformity

Manufacturer: As above

Details of Electrical Equipment

Model Number: V162SD with 28” Hantarex Monitor

Model Name: Tokyo Wars SD

Description: Video Arcade Entertainment Machine

Serial Numbers: 36092 ~ 36191, 36889

Directives this equipment complies with: 89/336/EEC relating to Electromagnetic Compatibility and 73/23/EEC amended by 93/68/EEC relating to Low Voltage

Harmonised Standards applied: BS EN 55014:1993 (Emmisions) BS EN 55104:1995 (Immunity) IEC 335-1:1991 IEC 335-2-82:1995 (draft)

Test Reports issued by: Notified/Competent Body Report No ERA Technology Ltd 4324/112 ERA Technology Ltd 97-0266

Year of Manufacture: 1997

Authorised Signatory: Date of Issue 24th March 1997

Namer~ M.J. Nevin Place of Issue

Position: Managing Director London, UK

Page 3

PORTABLE APPLIANCE TESTING

Please Note:

During testing of the machine with a portable appliance tester the insulation test will show a failure due to the fitting of two VDRs between live / earth and neutral / earth.

These components have been fitted to safeguard against high voltage surges that may occur on the mains supply to the machine and to comply with the EMC regulations.

To conduct an insulation test on this machine, the VDRs must be isolated from the circuit first.

Ensure that the VDRs are reconnected after the insulation test has been completed and before the machine is placed back into service.

The VDRs used have been specified and tested as safety critical components.

Page 4

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private or public use, without permission from NAMCO EUROPE LIMITED.

While the information contained in this manual is given in good faith and was accurate at the time of printing. NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.

This machine has been manufactured in accordance with Eiropean Community Directives, and has been tested and complies with the Directives 89/336/EEC and 72/23/EEC by the application of EN55014, EN55104 and EN60335-1 standards (see front of manual) and as such bears the C€ marking. Any changes or modifications to this machine must be in accordance with the European Directives. Any unauthorised changes to this product, may contravene such Directives.

Under some conditions of extreme external interference, e.g. radio transmissions, electrostatic discharge or mains borne transients, some degradation of performance may occur. However the machine will recover normal performance once the source of the interference has ceased or been removed. Following abnormally high surges on the mains supply, the video monitor may need to be manualy reset by turing the machine OFF and back ON.

Note: If the game processor resets due to an interuption or reduction of the mains voltage any credits established may be lost.

This game is not a machine as defined by the Machinery Directive 89/392/EEC

SAFETY WARNING

In order to use this machine safely, be sure to read this Operators Manual carefully before installation, adjustment or use of this machine.

Whenever the owner of this machine entrusts dis-assembly, installation, adjustment or routine maintenance to another person, the owner should ensure that that person read the appropriate precautions and relevant sections of this manual before stating work.

In order that no accidents occur when the machine is in operation, strictly follow the notes on safety as described below.

This manual along with the Installation Manual (where applicable) form an integral part of the equipment and must be available to the operating and service personnel at all times.

This machine is for indoor use only and should only be used for the purpose intended.

Namco Ltd. bears no responsibility for accidents, injury or damage resulting from unauthorized changes to, or improper use of this machine.

SAFETY NOTES

The following safety notes are used throughout this manual. Familiarize yourself with each of these notes and its, meaning before installing, servicing or making adjustments to this machine.

WARNING /\ Warning denotes a hazard that could result in injury or death. Do not proceed beyond a
warning note until the indicated conditions are fully understood and met.
CAUTION (1) Caution denotes a hazard that could result in damage to the machine. Do not proceed beyond a
warning note until the indicated conditions are fully understood and met.

GENERAL SAFETY CONSIDERATIONS

Only operate this machine after checking that it has been installed correctly and in accordance with the manual

If there is an error or problem with the machine, operation must be stopped immediately and the problem rectified before any further use.

Installation, service, adjustment or routine maintenance should be carried out by suitably qualified persons only.

For continued protection against fire hazard, replace the mains-in fuses with the same type and rating. The use of other fuses or material is prohibited.

The power supply inside the monitor will remain hot and have areas of high voltage even though the machine has been turned OFF, and there is the possibility of burns or electric shock. Be careful not to touch these areas.

To prevent possible electric shock due to failure, this machine MUST be fitted with a securely connected EARTHED plug

If at any time the mains supply lead becomes damaged, it must be replaced immediately.

Do not turn the power switch ON until the machine has been installed correctly.

Before connecting the machine to the mains supply, ensure that the machine is set for the correct voltage and that the correct fuses are fitted OPP PEP BPE BP &

Page 5

Va NOTES ON INSTALLATION

A\ NEVER turn the power to the machine ON until installation has been completed pba wonornere g = warm, | A In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected earthed plug.

(0) In order to avoid damage to the machine due to mis-operation,

ensure that the voltage of the mains supply is 230volts AC.

Note: If the location of this machine has a polished floor, it is recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor.
Note: In order to gain access to the Power Supply and CPU assemblies, make sure that the rear of the machine is separated from a wall or other machine by at least 500mm. \ KK \ YX \ \mn\\ WW a

MOVING THE MACHINE

A\ This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface.

A\ The overall height of the machine, with the Header Assembly fitted, is 2050mm. Take care of any overhead obstructions. (e.g. Light Fittings, Electric Cables etc.)

~\ REMOVING AND REPLACING PARTS

Adjustments or maintenance on this machine should be carried out by suitably qualified personnel only.

Do not make any alteration to this machine without prior approval. Doing so could cause unforeseeable

danger.

Only parts specified by Namco Europe Ltd should be used when replacing or repairing parts. (Including screws).

Ensure that the power to the machine is turned OFF before commencing any maintenance work. (Trouble shooting, repairs etc.)

If performing work not described in this manual, be sure to contact your distributor for instructions, as no responsibility will be accepted for damage or injury.

Parts of the Power Supply and Monitor remain hot and carry high voltage even after switching OFF and could cause burns or electric shock. Take care not to touch these parts accidentally.

Make sure that the machine is switched OFF before connecting or disconnecting any plugs or connectors. Pe BP BP BP BP BBE

When removing the mains connector from the machine, or the mains plug from the wall outlet, always grasp the plug and not the cable. Va

Page 6

<> Dieses Dokument darf in keiner Weise vervielfaltigt werden. Jegliche Tonautnahmen sowie die Speicherung auf Datentrager (Suchsysteme), die Weitergabe oder sonstiges Kopieren fur den gewerblichen und privaten Gebrauch sind untersagt und bediirfen der vorherigen Genehmigung durch NAMCO EUROPE LIMITED.

Die informationen in diesem Handbuch entsprechen den Tatsachen bei Drucklegung. NAMCO EUROPE LIMITED behait sich jedoch das Recht zu Anderungen ohne vorherige Bekanntgabe vor.

Dieses Gert tragt das CE-Zeichen und wurde gemaB den EU-Richtlinien produziert. Es erfillt die Richtlinien 89/336/EEC und 72/23/EEC und Standards EN 55014, EN55104 und EN60335-1 (s. Deckblatt des Handbuches). Alle Verénderungen an diesem Gert missen in Ubereinstimmung mit den EU-Richtlinien erfolgen. Nicht genehmigte Veranderungen an diesem Gerat verstoBen gegen diese Richtlinien

Extreme uBere Stdrungen, wie z.B. durch Radiobetrieb, elektrostatische Entladung oder zeitweilige Netzschwankungen kénnen zu einer Leistungsminderung fuhren. Sobald diese Faktoren jedoch ausgeschaltet oder beseitigt wurden, erreicht das Gert seine normale Leistung.

Achtung! Falls der Spielprozessor auf Grund von Netzunterbrechungen oder Abnahme der Netzspannung aussetzt, kann es zum Verlust von Spielkrediten kommen.

Dieses Gert fallt nicht unter die Maschinen-Richtlinie 89/392/EEC

SICHERHEITSHINWEISE

Um einen ordnungsgemaBen Betrieb dieses Gerdtes zu gewahrleisten, muB vor Aufstellung, Inbetriebnahme und Gebrauch das Handbuch sorgfaltig gelesen werden. Sobald der Besitzer dieses Gerates die Demontage, Aufstellung, Inbetriebnahme oder den Service einer anderen Person ibertragt, muB er sicherstellen, daB diese Person vor Arbeitsbeginn die nétigen Sicherheitshinweise und die dazugehérigen Kapitel des Handbuches liest und versteht. Um jegliche Unfalle wahrend des Betriebes zu vermeiden, mussen obige Hinweise strikt befolgt werden Dieses Handbuch sowie das spezielle Gerate-Handbuch (wenn vorhanden) gehdren zum Gerat und missen dem Betreiber und Wartungspersonal stets zugainglich sein. Dieses Gerat ist ausschlieBlich fir den gewerblichen Gebrauch in geschlossenen Raumen bestimmt und darf nur dort betrieben werden. NAMCO LTD. tibernimmt keinerlei Haftung flir Unfalle, Verletzungen oder Beschadigungen, die auf nicht genehmigte Veranderungen oder unsachgemaBen Betrieb des Gerdtes zuriickzufihren sind.

SICHERHEITSHINWEISE

Folgende Sicherheitsbegriffe werden im gesamten Handbuch benutzt. Machen Sie sich daher bitte vor Inbetriebnahme, Wartung und Durchfiihrung von Einstellungen am Gerat mit diesen Warnhinweisen vertraut.

WARNUNG /\ WARNUNG bezeichnet eine Gefahrenquelle far Leib und Leben. Erscheint dieser Warnhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklarungen vollstandig verstanden und befolgt wurden.

VORSICHT (7) VORSICHT bezeichnet eine Gefahrenquelle fir die Beschadigung des Gerdes. Erscheint dieser Warnhinweis, dart erst weitergearbeitet werden, wenn die entsprechenden Erklarungen vollstandig

ALLGEMEINE SICHERHEITSHINWEISE

Das Gerat darf nur betrieben werden, nachdem es vorschriftsmaBig und in Ubereinstimmung mit dem Handbuch aufgestellt wurde.

Bei Auftreten eines Fehlers oder Problems muB das Gerat sofort abgeschaltet werden und darf erst nach fachgerechter Behebung des Fehlers wieder in Betrieb genommen werden.

Aufstellung, Service, Einstellungen und Wartung durfen nur von dafur qualifiziertem Fachpersonal durchgefuhrt werden

Zur Vermeidung von Feuer, defekte Sicherungen nur durch vorgeschriebene Sicherungen ersetzen. Die Verwendung von andersartigen Sicherungen oder unterschiedlichem Material ist untersagt.

Das Netzteil im Monitor bleibt nach Ausschalten des Gerates noch heiB und fiihrt weiterhin Hochspannung. Daher besteht die Gefahr von Verbrennungen und Elektroschlagen. Diese Bereiche dirfen nicht beruhrt werden.

Zur Vermeidung von Elektroschlagen muB dieses Gerat mit einem ordnungsgemaB geerdeten Netzstecker versehen sein

Bei Beschadigungen des Netzteiles muB dieses umgehend ersetzt werden

Gerat erst nach abgeschlossener Aufstellung einschalten. OP BPBBBP BB B&

Vor Einstecken des Netzsteckers bitte sicherstellen, daB Netzspannung und Geratespannung Ubereinstimmen, und die vorgeschriebenen Sicherungen verwendet wurden.

Page 7

HINWEISE ZUR AUFSTELLUNG

A NIEMALS das Gert einschalten bevor die Aufstellung villig abgeschlossen ist. sonora

A\ Zur Vermeidung von Elektroschlagen muB das Gerat mit einem ordnungsgemaB geerdetem Netzstecker an die Stromversorgung angeschlossen werden.

(0) Zur Vermeidung von Beschadigungen durch Fehlbetrieb am

Gerat sicherstellen, daB die Netzspannung 230 Volt betragt.

Hinweis: Ist das Gerat fir einen Aufstellplatz mit glattem FuBboden bestimmt, miissen die Standbeine mit Gummiplattchen unterlegt werden, damit das Gerat fest steht und nicht auf dem Boden hin- und herrutscht.

Hinweis: Zu Reparaturzwecken am Netzteil und den CPU- Komponenten muB die Riickseite des Gerates mindestens 50cm von anderen Geraten und der Wand entfernt sein. \ \ \« SS WW ~~)

Z\ Zum leichteren Transport ist das Gerat mit Rollen ausgerUstet. Daher besondere Vorsicht auf abschissigem Boden.

Z\ Die Gesamthohe de Gerates betragt 2050mm. Daher Vorsicht bei tiefer hangenden Beleuchtungskorpern.

Einstellung und Wartung des Gerates diirfen nur von qualifiziertem Fachpersonal vorgenommen werden.

Page 8

@B Aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen d'enregistement phonographique. Ces informations ne seront ni stockées grace A un procédé de récupération, ni transmises ou autrement copiées pour un usage publique ou privé, sans l'autorisation de NAMCO EUROPE LIMITED.

Malgré le fait que les informations contenues dans ce manuel soient données de bonne foi et étaient actualisées au moment de leur impression, NAMCO EUROPE LIMITED se réserve le droit de procéder & des changements ou a des modifications sans avis préliminaire.

Ce jeu a été fabriqué en respect des normes de la Communauté Européenne, aprés avoir été testé il repond aux normes 89/336/EEC et 72/23/EEC, en application des standards EN55014, EN55104 et EN60335-1 (voir la couverture du manuel), et comme tel il comporte l'autocollant de conformité avec les normes de la Communauté Européenne. Tout changement non autorisé sur ce produit pourrait contrevenir & ces normes.

Sous certaines conditions extrémes d'interlérence exteme, par example des transmissions radio, des décharges électrostatiques ou bien de interférences passagéres sur le réseau, certaines dégradations ou anomalies peuvent se produire. Le jeu retrouvera cependant son état normal de fonctionnement lorsque la cause de ces anomalies aura cessé ou se trouvera déplacée.

Note:- Si le processeur du jeu se reprogramme suite & une interruption ou une réduction de lalimentation, les crédits qu'il aurait pu contenir peuvent se trouver perdus.

Ce jeu n'est pas une machine, telle que définie par la norme sur les machines 89/392/EEC

MESURES DE SECURITE

Afin d'utiliser ce jeu en toute sécurité, bien lire ce manuel d'utilisation avant de procéder a son installation, son réglage ou son exploitation. Si le propriétaire de ce jeu en confie la démontage, installation, le réglage ou la maintenance habituelle & une autre personne, il devra s'assurer que cette personne ait lu les conseils d'utilisation et les passages du manuel se rapportant a ce théme, avant qu’elle ne commence son travail. Afin d’éviter tout accident pendant la durée d’exploitation de ce jeu, se conformer strictment aux conseils de sécurité décrits a la suite. Ce manuel ainsi que le manuel d'installation du jeu (la ol nécessaire) font partie des éléments nécessaires a installation de la machine et doivent étre mis a la disposition de l'utilisateur et du personnel de maintenance & tout moment. Ce jeu est uniquement destiné a un usage intérieur et devra étre utilisé comme tel. Namco Ltd. ne sera aucunement tenu responsable en cas d’accidents, de blessure ou de dommage quelconque résultant de modifications non autorisées ou d'usage impropre du jeu.

REMARQUES SUR LA SECURITE

Les termes de sécurité détaillés a la suite seront utilisés tout au long de la lecture de ce manuel. Il convient de vous familiariser aves chacun de ces termes ainsi que leur signification avant de procéder a l'installation, a la maintenace ou au réglage du jeu. AVERTISSEMENT Z\ Ce terme annonce un danger qui pourrait éventuellement avoir des conséquences dommageables ou mortelles. Ne pas passer odtre ce signal jusqu’a ce que les conditions indiquées soient entiérement comprises et effectuées

ATTENTION (2) Ce terme indique qu’un danger menace la machine. Ne pas passer olitre ce signal jusqu’a ce que les Conditions indiquées soient entiérement comprises et effectuées.

CONSIGNES GENERALES DE SECURITE

Allumer l'appareil seulement aprés avoir vérifié qu'il a été correctement installé, et que les instructions du manuel ont été respectées S'il y una erreur ou un probléme avec la machine, l'utilisation doit étre immédiatement interrompue et le probleme résolu avant toute nouvelle utilisation.

Linstallation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.

Afin d’éviter un éventuel incendie, s'assurer que les fusibles soient remplacés par le méme type de fusibles et au bon voltage. L'utilisation d’autres sortes de fusibles ou autres matériels est interdite.

L’alimentation a l’intérieur du moniteur reste chaude et comporte des zones de haute tension méme si la machine est éteinte. Il existe donc un risque de brilure ou d’électrocution. Attention a ne pas toucher ces endroits.

Pour prévenir une éventuelle électrocution due a un défaut matériel, ce jeu DOIT étre muni d’une prise de TERRE connectée en toute sécurité

Si A tout moment les fils électriques sont endommagés, il faut les remplacer immédiatment

Ne pas mettre le jeu en mode de fonctionnement avant qu’il n’ait été correctement installé.

Avant de connecter la machine au réseau, s’assurer que la machine est installée sous la bonne tension et que les fusibles correspondent. OP PB BEB BP BBE

Page 9

NOTES D’ INSTALLATION

Note:
Note:

50cm NE JAMAIS mettre le jeu en marche avant que Vinstallation ne soit complétement effectuée.

Afin de prévenir une éventuelle électrocution, s'assurer que la machine est connectée au réseau avec une prise de terre reliée selon les normes de sécurité. Afin d’éviter que la machine ne soit abimée suite a une mauvaise opération, s’assurer que la tension sur le réseau principal soit de 230 volts AC.

Si endroit ou doit étre installée la machine a un sol pdli, il est recommandé de poser des tampons feutrés sous les vérins pour éviter que le jeu ne glisse sur le sol

Afin de facilité 'accés aux CPU at a alimentation, s'assurer qu'il y a un espace d’au moins 500 mm entre l'arriére du meuble et le mur ou tout autre jeu. \ von anderen Geraten und der Wand entfernt sein.

Le jeu est foumi avec des roulettes pour une meilleure mobilité. Prendre garde quand la machine est déplacée sur une surface inclinée.

Le centre de gravité de la partie supérieure du jeu est situé sur l’avant, il est donc indispensable que deux personnes au moins soient employées pour installer ou déplacer la partie supérieure. La hauteur totale de l’assemblage principal est de 2050 mm, prendre garde aux encombrements de la partie supérieure (ex : illuminations du bandeau).

> BP BPP BP BB DEPLACER ET REMPLACER LES UNITES ET LES PIECES DETACHEES.

Linstallation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées

Ne pas apporter de modifications sur cette machine sans autorisation préalable, faute de quoi cela pourrait entrainer un danger.

Seules les piéces détachées Namco Europe Ltd. doivent étre utilsées pour le remplacement ou la réparation de piéces (y compris les vis)

S'assurer que interrupteur soit sor OFF avant de commencer tout travail de maintenance (localisation d'une panne, reparations, etc.)

Si dans ce manuel il manque une information pour réaliser un quelconque travail, contacter votre distributeur, car aucune responsabilité ne sera acceptée en cas de domage ou de blessure.

Les piéces de I'alimentation et du moniteur restent chaudes, a tension élévée méme lorsque la machine est hors tension, elle pourrait occasionner des brilures ou des électrocutions. Attention de ne pas toucher ces endroits accidentellement.

S’assurer que la machine soit hors tension avant de brancher ou débrancher toute prise ou connecteur.

Lorsque l'on manipule la prise au réseau de la machine, ou lorsque les prises principales doivent étre débranchées, saisir toujours la prise, et non le cable. ~\

wy

Page 10

CD Nessuna parte di questa pubblicazione pud essere riprodotta con processo meccanico, fotografico o lettronico, né sotto forma di registrazione fonografica, nd pud essere memorizzata in un sistema di salvataggio, trasmessa o in altro modo copiata per uso pubblico 0 privato, senza l’autorizzazione di NAMCO EUROPE LIMITED. Le informazioni contnute in questo manuale sono state date in buona fede ed erano accurate al momento della pubblicazione. Tuttavia NAMCO EUROPE LIMITED, si riserva il diritto di apporre cabiamenti e variazioni senza alcun preawviso.

Questo apparecchio é stato costruito in conformita alle Direttive della Comunita Europea, ed @ stato provato e soddisfa le Direttive 89/336/EEC e 72/23/EEC per l’'applicazione degli standards delle norme EN55014, EN55104 e EN60335-1 (vedi fronte del manuale), e per questo porta il marchio CE. Qualsiasi cambiamento o modifica di questo apparecchio deve essere in conformita con le Direttive della Comunita Europea.

In caso di condizioni di estrema interferenza dall’esterno, per esempio trasmissioni radio, scariche elettrostatiche o transitori sulla linea, pud verificarsi un decadimento delle prestazioni. Comunque l'apparecchio ritornera al rendimento normale quando la sorgente dell,interferenza avr cessato di emettere o sara stata rimossa.

Nota bene: se il processore del gioco “resetta” a causa di una interruzione o diminuzione del voltaggio di linea, un eventuale credito, gia concesso, pud essere annullato.

Questo goco non é una macchina cosi come viene definita dalla Direttiva Macchine 89/392/EEC.

AVVERTENZE PER LA SICUEZZA

Allo scopo di usare questo apparecchio in sicurezza, leggere questo Manuale dell’operatore attentamente prima dell'installazione, regolazione o uso di questa macchina. Tutte le volte che il proprietario di questo apparecchio affida lo smontaggio, l'installazione, la regolazione o la manutenzione ordinaria ad un’altra persona, il proprietario stesso deve assicurarsi che quella persona legga le precauzioni necessarie e i paragrafi importanti di questo manuale prima di iniziare a lavorare. Perché non succeda alcun incidente quando la macchina é operante, seguire rigorosamente le note sulla sicurezza come specificato piu avanti Questo manuale insieme con il manuale di installazione (dove si pud applicare) forma una parte integrante dell’apparechio e deve essere disponibile sempre al personale operante e di servizio. Quest macchina deve essere usata solo in interni e deve essere usata solo per gli scopi per cui é progettata. Namco Europe Ltd non si assume responsabilita per incidenti, ferite 0 damni risultanti da cambiamenti non autorizzati o da uso improprio della machina.

NOTE PER LA SICUREZZA

Le seguenti note sulla sicurezza sono usate dal principio alla fine di questo manuale. Valutare attentamente ciascuna di queste note ed il loro significato prima di installare, fare assistenza o regolazioni su questa macchina.

WARNING /\, “Warning” evidenzia un rischio di ferita o di morte. Non procedere oltre una nota “Warning” finché le awertenze specifcate non siano completamente capite e conosciute.
CAUTION (7) Caution” evidenzia un rischio di danneggiare la machina. Non proceder oltre una note “Caution” finché le awertenze specificate non siano completamente capite e conosciute.

CONSIDERAZIONI GENERALI SULLA SICUREZZA

Mettere in funzione l’'apparecchio solo dopo aver controllato che l’installazione sia stata effettuata correttamente ed in conformita alle istruzioni del manuale. Se vi sono errori o problemi con la machina, si deve interrompere il funzionamento immediatamente e risolvere il problema prima di ogni ulteriore uso.

Liinstallazione, l’assistenza, le regolazioni e la manuzenzione ordinaria devono essere eseguite solo da persone idonee e qualificate.

Per una protezione costante contro il rischio di fuoco, assicurarsi che i fusibili sulle alimentazioni siano solo sostituiti con lo stesso tipo e caratteristiche. L’uso di altri fusibili o materiali é proibito. L’alimentatore all’interno del monitor rimane caldo ed ha zone di alto voltaggio anche se la machina é stata spenta, c’é quindi la possibilita di bruciature o scosse elettriche. Fare attenzione a non toccare queste zone

Per prevenire possibili scosse elettriche dovute a difetti, quest macchina DEVE essere installata con un connettore sicuramente MESSO A TERRA.

In caso il cavo di alimentazione di rete risultasse danneggiato deve essere sostituito immedatamente.

Non accendere la macchina finché la stessa non é stata installata completamente e correttamente.

Prima di collegare la macchina alla rete, assicurarsi che la machina sia preparata per il voltaggio corretto e che siano inseriti i fusibili adatti. OPP BPE BP BP BBE

Page 11

NOTES D’ INSTALLATION

A NON ACCENDERE MAI la macchina finché linstallazione non é stata completata. 1 wemermere menermee Allo scopo di prevenire possibili scosse elettriche, la macchina deve essere obbligatoriamente collegata alla rete con un connettore messo a terra con connessioni sicure.

(0) Per evitare danni alla macchina durante la

messa in opera, assicurarsi che il voltaggio della rete sia 230 volts AC. >

Note: II luogo di destinazione della macchina deve avere il pavimento liscio e si raccomanda di

i re dei cuscinetti di i piedini VW

della macchina sul pavimento. SXQV»xv

Note: Per garantire l'accesso all’alimentatore e alla scheda madre, assicurarsi che il retro del mobile principale sia separato dalla parete o da altre macchine di almeno 500mm. meuble et le mur ou tout autre jeu.

ll gioco @ fornito di ruote per rendere piu facile il suo spostamento. Fare attenzione quando si muove la macchina su una superficie inclinata.

L’altezza totale della parte principale é 2050mm, fare attenzione ad eventuali ostacoli soprala testata ovvero ad eventuali installazioni di luci.

>BEP BBP BP BP B RIMOZIONE E SOSTITUZIONE DI GRUPPI E PARTI STACCATE

Linstallazione, l’assistenza, le reglioni e la manuzenzione ordinaria essere eseguite solo da persone idonee e qualificate.

Non apporre alcuna modifica alla machina senza autorizzazione preventiva. Il fare questo pud causare un pericolo non prevedibile.

Quando si rimpiazza o si riparano delle parti ( incluse le viti) si possono usare solo parti approvate dalla Namco Europt Ltd Assicurarsi che la macchina sia SPENTA prima di incominciare qualsiasi lavoro di manutenzione (guasti, riparazioni etc.)

Se state per iniziare un lavoro non decritto in questo manuale, contattate il vostro distributore per instruzioni poché non si accetta alcuna responsabilita per danni o ferite.

Parti dell'alimentatore e del monitor rimangono caldi o portano alta tensione anche dopo aver spento l'apparecchiatura e possono causare bruciature o scosse elettriche. Attenzione a non toccare queste pati accidentalmente.

Assicurarsi che la machina abbia l’interruttore nella posizione OFF prima di inserire o disinserire qualsiasi connettore o spina.

Quando vengono rimossi i connettori principali dalla machina oppure la spina dell’alimentazione dalla parete bisogna sempre afferrare il connettore e non il cavo /

Page 12

GE)

Tasta julkaisusta ei saa ottaa misséan muodossa kopioita yksityis- tai julkiseen kaytt66n ilman NAMCO EUROPE LIMITED:in lupaa.

TassA ohjekirjassa olevat tiedot pitavat julkaisuhetkella paikkansa. NAMCO EUROPE LIMITED:illa on kuitenkin oikeus muutoksiin ilman erillista ilmoitusta.

Tama laite on valmistettu EC direktiivien mukaisesti. Se on testattu ja todettu noudattavan seuraavia direktiiveja: 89/336/EEC ja 72/23/EEC (EN55014, EN55104 ja EN 60335-1 standardit). Nain ollen tama laite on varustettu CE-merkinnalla. Kaikki tahan laitteeseen kohdistetut muutokset on tehtava EC- direktiivien mukaisesti. Mika tahansa valtuuttamattoman huoltomiehen tekema muutos voi olla direktiivien vastainen.

Laitteen toiminta voi hairiintya maaratyissa olosuhteissa, jotka johtuvat 4arimmaisist ulkoisista sahkohairidista, kuten radiolahetys, elektrostaattinen purkaus tai vahvavirrasta syntynyt hairié. Toiminta normalisoituu kuitenkin heti, kun ulkoinen shkéhairié on poistettu.

Huom:- Jos peliprosessori resetoituu sahkdkatkoksen tai vastaavan johdosta, voivat kaikki pelivaraukset havita.

Tama laite ei ole 89/392/EEC direktiivien mukainen kone.

Turvallisuusvaroitus

Taman laitteen turvallinen kayttd edellyttéa kayttéohjekirjan huolellista lukemista ennen laitteen asennusta, sdatda tai kaytt

Jos taman laitteen omistaja antaa jollekin toiselle osapuolelle tehtavaksi purkaa, asentaa, sata tai muuten huoltaa laitetta, on omistajan varmistuttava siita, ett toinen osapuoli on lukenut ja ymmértanyt kayttéohjekirjan oleelliset osat ennen tyéhén ryhtymista.

Turvallisuusohjeita on seurattava tarkoin vahinkojen valttamiseksi laitteen ollessa kaytéssa .

Tama ohje seka mahdollinen asennusohje muodostavat laitteiston oleellisen osan ja on siksi aina oltava huolto- ja kayttohenkildkunnan kaytettavissa.

Tama laite on tarkoitettu vain sisatilakaytté6n. Sita ei saa kayttaa muihin tarkoituksiin.

Namco Ltd ei vastaa niista onnettomuuksista, loukaantumisista tai vahingoista, jotka johtuvat laitteeseen ilman Namco Ltd:n lupaa tehdyista muutoksista laitteen vaarasta kaytosta.

Turvallisuusohjeet

Tass kayttdohjekirjassa on kaytetty seuraavia turvallisuuteen liittyvid huomautuksia. Tutustu jokaiseen ndista. Ald asenna, huolla tai sA&da laitteistoa, ennen kuin olet taysin ymmartanyt mita ne tarkoittavat.

VAARA /\— “Vaara” tarkoittaa uhkaa, joka voi johtaa loukkantumiseen tai kuolemaan, Ala koskaan ohita Vaaramerkintaa, ennenkuin ohjeissa esitetyt olosuhteet on ymmarretty taysin.

VAROITUS (1) “Varoitus” tarkoittaa uhkaa, joka voi johtaa laitteen vioittumiseen. Ala koskaan ohita Vaara-merkintaa, ennenkuin ohjeissa esitetyt olosuhteet on ymmarretty taysin.

YLEISET TURVALLISUUSNAKOKOHDAT

Varmista, etta laite on asennettu oikein ja ohjekirjan mukaisesti ennen kayttédnottoa.

Jos laitteeseen tulee vika tai ongelmia, on se pysaytettava valittémasti ja ongelma selvitettava ennen uutta kayttédnottoa

Vain riittavan at kohdistuvia ru attipatevyyden omaava henkilé saa suorittaa asennus-, huolto-, sAaté- tai muita laitteeseen itoimenpiteita.

Jotta palovaaraa ei syntyisi, saa padsulakkeita vaihtaa vain samankokoisiin sulakkeisiin. Muiden sulakkeiden tai materiaalin kaytté on ehdottomasti kielletty.

Monitorin sisalla oleva virtalahde pysyy kuumana ja siina on alueita, joissa on korkeajannite vaikka laite on kytketty pois paalta. Palovammojen tai sahkdiskun saaminen on mahdollista. Ala koske naihin alueisiin Sahkdiskujen valttamiseksi vikatapauksissa, laite on ehdottomasti kytkettava maadoitetulla johdolla maadoitettuun pistorasiaan.

Vioittunut verkkojohto on valittomasti vaihdettava.

Ala kytke laitetta paalle, ennen kuin se on oikein asennettu. OPP BBE BP BE BBE Varmista ennen verkkoon kytkemistA, ett virtaléhteen jannitteen asetus on asetettu oikealle jannitteelle ja etta sii oikeat sulakkeet.

Page 13

A

0) ASENNUSHUOMIOITA Y

stoonormere Ala koskaan kytke laitetta paalle ennen kuin asennus Lp ener Sencrnom st on suoritettu loppuun. |

Taman laitteen virtalahde on kytkettava maadoitetulla johdolla maadoitettuun pistorasiaan, jotta sahkdiskun vaaraa ei olisi

Varmista, etta virtalahteen jannite on 230V AC, jotta ei laite vioitu.

Huomio: Jos tama laite sijoitetaan liukkaalle esim, vahatulle lattialle, AN AN suositellaan laitettavaksi kumityynyt saatdjalkoihin XV MX XV : liikkumisen estamiseksi. Pathway NS Nee Huomio: Varmista, ettatakaosan taakse jaa vahintéan 500mm tilaa, jotta virtalahteeseen ja CPU-korttiin paasee kasiksi. Ne

A Laite on varustettu kaantyvilla pyorilla. Tama on pidettava mielessa, kun laitetta siirretaan kaltevalla alustalla.

A Laitteen kokonaiskorkeus on yli 2300 mm. Varmista, ettei katossa ole esteita. esim. valaisimia.

Va

> PPE BP BB

> & OSIEN JA OSAKOKONAISUUKSIEN POISTO JA VAIHTO

Vain riitavan ammattipatevyyden omaava henkil6é saa suorittaa asennus-, huolto-, saatotai muita laitteeseen kohdistuvia rutiinitoimenpiteita.

TAlle laitteelle ei saa tehda mitaan hyvaksymatt6mia muutoksia. Se voi aiheuttaa ennalta-arvaamattomia vaaroja.

Vain Namco Europe Ltd:n maarittelemia varaosia saa hayttaa vaihtaessasi tai korjatessasi osia. (sisaltaen ruuvit).

Varmista, etta laite on kytketty POIS PAALTA ennen ty6n aloittamista.

Ota yhteytta maahantuojaan objeita varten, jos joudut tekemaan tyatehtavia, joita ei ole esitelty huoltokirjassa, muuten vastuuta vioista tai loukkaantumisista ei ole.

Virtalahde ja monitori pysyvat kuumina ja niissa on alueita, joissa on korkeajannite vaikka laite on kytketty pois paalta. Palovammojen tai sahkéiskun saaminen on mahdollista. Ala koske naihin laitteisiin.

Varmista, etta laite on kytketty POIS PAALTA ennen johtojen kytkemista tai irrottamista.

Irrottaessasi verkkojohdon seinasta, ota kiinni itse pistokkeesta, ei johdosta.

Page 14

Contents

CERTIFICATE OF CONFORMITY .........cccscceseseesescseseeeeeseeeeeeseeeecesseeesetesenseseneee 2 PORTABLE APPLIANCE TESTING.... SAFETY WARNING NOTES ON INSTALLATION . MOVING THE MACHINE REMOVING AND REPLACING PARTS... ALLGEMEINE SICHERHEITSHINWEISE CONSIGNES GENERALES DE SECURITE CONSIDERAZIONI GENERALI SULLA SICUREZZA... YLEISET TURVALLISUUSNAKOKOHDAT...

  • SPECIFICATIONS
  • HOW TO PLAY
  • MAJOR COMPONENTS ...
  • MOVING THE MACHINE ..
  • INSTALLATION 6 ADJUSTMENTS ... 6-3 Test Mode

6-3-1 Coin Options .... 6-3-2 Game Options . 6-3-3 Effect Test...

6-3-4 Switch Test...

6-3-5 Monitor Test .

6-3-6 Sound Test...

6-3-7 Displaying and Resetting the Game Data .. 6-3-8 Displaying the Archive Data 6-4 Initialization after Replacing Parts . 6-5 Self Test

6-6 Linking Two Machines 6-6-1 Setting the Link Switches ...

  • MAINTENANCE 7-1 Replacing the Fluorescent Tube, Starter and Lamps. 7-2 Replacing the Viewpoint and Credit Available Switches. 7-3 Removing the Steering Wheel 7-4 Replacing the Trigger Button 7-5 Replacing the Steering Potentiometer-... 7-6 Removing the Pedal Assembly 7-7 Replacing the Pedal Potentiometer...
  • SCHEMATIC...
Page 15
  • SPECIFICATIONS

POWER SUPPLY:- 230volts AC

AMBIENT OPERATING TEMPERATURE:-

+5°C to +25°C

MONITOR:- Hantarex 28” Polo Monitor

COIN ACCEPTOR:- Mars CashFlow - Dispense

DIMENSIONS:- Assembled 1400(w) x 1650(d) x 2050(h)

Cabinet 1400(w) x 930(d) x 2050(h) Seat Assy 490(w) x 820(d) x 1330(h)

WEIGHT:-

Assembled 345kg

Cabinet 295kg Seat Assy 25kg

ACCESSORIES:- Keys: (Cash Door)... (Coin Door) (Back Door)...

IEC Mains Lead ........cccceeeeeees 1

Operators Manual.........ccccceee 1

Monitor Manual ...........0.cccceceeseeee 1

CashFlow Documents ............005 1

Link Cable 4M... cceceeeeeeeee 1

M4 Security Wrench... 1

M5 Security Wrench..........cccce 1

M6 Security Wrench..........cccce 1

Page 16
  • HOW TO PLAY

This game is a multi-player fighting game where one or two players join two armies to fight against the opposing army. By using the steering wheel and accelerator pedals, a player controls their tank and moves freely in the city limits in order to search out and attack the enemy.

OPERATION

1)Stepping on the forward pedal (right pedal):Player’s tank moves

forward.

  • Stepping on the backward pedal (left pedal): | Player’s tank moves backwards.
3)Turning the steering wheel:Players gun barrel and

tank turn in the direction that the wheel has been turned.

4)Pushing the trigger button (left or right):Players tank fires a shot.
5)Pushing the Viewpoint Button:Possible to switch

between the third person view or the first persons view.

GAME RULES

  • The player joins either the green army or white army and tries to destroy the enemy.
  • When a player destroys an enemy tank, a shield restoration item appears. If it is touched and obtained, a certain amount of damage to the players tank is restored.
  • Even if a player’s or computer’s tank is destroyed, they can continue playing whilst there are remaining tanks in their army.
  • The game is over when either army has been totally destroyed, or the game time reaches zero.

STAGE

The stage can be selected from two options. One is the small bay area with a simple shape. The other is the large centre of a city with a complicated shape.

BACKGROUND MUSIC

The player who has inserted coins first can select the BGM played during the game. Before the game starts, the sound title is displayed while the enemy / allies are being displayed. The tune can be changed by pressing either trigger button.

Page 17
  • MAJOR COMPONENTS

Header Assy

Seat Assy

Pedal Assy ‘Steering Assy Coin Assy

$S22 PCB Assy

Mains In / ON/OFF

Page 18

4. MOVING THE MACHINE

when moving the machine on an inclined surface.

The overall height of the machine, with the Header Assembly fitted, is 2050mm. Take care of any overhead obstructions. (e.g. Light Fittings, Electric Cables etc.) MOVING THE MACHINE

A\ This machine is fitted with castors to make it easier to move. Take care

A

§. INSTALLATION

NOTES ON INSTALLATION

Z\ NEVER turn the power to the machine ON until installation has been completed.

A\ |n order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected earthed plug.

© |n order to avoid damage to the machine due to mis-operation, ensure that the voltage of the mains supply is 230volts AC.

Note: If the location of this machine has a polished floor, it is recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor.
Note: In order to gain access to the Power Supply and CPU assemblies, make sure that the rear of the machine is separated from a wall or other machine by at least 500mm

A This machine is designed for INDOOR USE ONLY. Do not install in the following places.

Outdoors Direct Sunlight, places with excessive humidity or dust, places where there is water leakeage, near air-conditioning or heating equipment, places with excessive heat or cold temperature. Places where it would be in the way of emergency exits or fire extinguishing equipment. Unstable places or places with excessive vibration. Places that are not level.

Page 19

®

ask

as A

DIESES GERAT IST NUR FUR DIE GEWERBLICHE AUFSTELLUNG IN GESCHLOSSENEN RAUMEN BESTIMMT. DAS GERAT DARF AN FOLGENDEN PLATZEN NICHT AUFGESTELLT WERDEN

Im Freien. In direktem Sonnenschein, an extrem feuchten und staubigen Platzen, an Platzen mit Wasseranschlissen und méglichen Leckagen, nahe Klima- und Heizungsanlagen, an Platzen mit extrem hohen oder niedrigen Temperaturen. In der Nahe von Notausgangen oder Feuerléschgeraten. An unstabilen Platzen oder Platzen mit UbermaBiger Vibration. An Platzen, die nicht eben sind.

CETTE MACHINE EST DESTINEE UNIQUEMENT A UN USAGE INTERIEUR NE PAS INSTALLER LA MACHINE DANS LES ENDROITS SUIVANTS

A l’extérieur. Directement exposée au soleil, aux endroits excessivement humides ou poussiéreux, aux endroits ou il y a des risques de fuite d’eau, prés de ventilateurs ou source de chaleur, aux endroits tres chauds ou froids. Dans des zones de proximité des sorties de secours ou d’accés aux équipements d’extinction du feu. Dans des emplacements instables ou soumis a de fortes vibrations. Dans des endroits dénivelés.

QUESTA MACCHINA E’ PROGETTATA PER ESSERE USATA ESCLUSIVAMENTE IN AMBIENTI INTERNI. NON INSTALLARE LA MACCHINA NEI SEGUENTI LUOGHI.

In ambienti esterni. Alla luce diretta del sole, in posti con eccesiva umidita 0 polvere, in luoghi dove ci siano infiltrazioni d’acqua, vicino ad apparecchi di condizionamento d’aria oppure riscaldamento, in posti eccessivamente caldi o freddi. In luoghi dove potrebbe esserci un uscita di emergenza 0 un’attrezzatura per lo spegnimento del fuoco. In posti non stabili o con eccessive vibrazioni. In luoghi non piani.

TAMA LAITE ON SUUNNITELTU VAIN SISAKAYTTOON ALA ASENNA LAITETTA SEURAAVIIN PAIKKOIHIN:

Ulkotilaan Suoraan aurinkovaloon, kosteisiin tai pdlyisiin paikkoihin, vesivuotopaikkojen laheisyyteen, ilmanvaihto- tai |lammityslaitteen lahistélle tai paikkoihin, jossa on erittain kuumaa tai kylmaa. Varauloskaytavien, muiden pakoteiden tai tulensammutusvalineiden eteen. Epavakaisiin tai tariseviin paikkoihin. Kaltevalle alustalle.

Page 20

5-1 Assembling the Machine

  • Remove the 16off (8 on each seat) Hex Head Screws (M10x25), Flat and Spring Washers and remove the Seat/Cabinet Joint Bracket from the Seat assembly.
  • Remove the 80ff Hex Head Screws (M10x25), Flat and Spring Washers from the front of the Monitor Cabinet.
  • Place the Seat Assemblies close to the Monitor Cabinet and connect the connectors.
  • Fit the Seat Assemblies to the Monitor Cabinet using the Seat/Cabinet Joint Brackets and the 24off Hex Head Screws (M10x25), Flat and Spring Washers removed in steps 1 & 2.
Note: Take care not to trap any wires when placing the Seat Aseemblies against the Monitore Cabinet.

Connector

‘Hex Head Screw (m10x25) Seat/Cabinet Joint Bracket

Hex Head Screw (m10x25) Level Adjuster

  • When the machine is fully assembled and in its final position, lower the 12 level adjusters (4 on each seat and 4 on the monitor cabinet), with a spanner, so that all the castors are raised from the floor by approximately 5mm, and the machine is level. Tighten the lock nuts with a spanner to ensure that the level adjusters do not move.

Castor

Sw © Level Adjuster

Page 21

6 ADJUSTMENTS

6-1 Turning on the Power

After the machine has been installed, turn ON the power. The power switch is located on the rear of the cabinet.

6-2 Adjustment Switches

The Adjustment switches are located inside the coin door

  • Service Switch Press the service switch to obtain game credits without incriminating the play meter.
  • Test Switch Slide the Test Switch ON to enter test mode. Test Mode allows the testing and changing of game settings. (Refer to section 6-3 “Test Mode” )

COIN COUNTER io)

°

© LEFT PLAYER RIGHT PLAYER OO O O

TEST SERVICE TEST SERVICE ©

Service Brac et

Page 22

6-3 Test Mode

  • Open the coin door and slide the test switch “on”. The menu screen will be displayed on the monitor.
  • Select the test required by turning the steering wheel left or right. The selected test will ‘blink’.
  • Enter the selected test by depressing the forward pedal (right pedal). Select “EXIT” to return to the “Menu Screen”.
  • After testing is completed, ensure that the test switch is returned to the “OFF” position to return to normal game mode.,

The Test Switch must always be in the “OFF” position for normal game mode.

~ MENU

COIN OPTIONS (1) Sets the price of play (See 6-3-1)

GAME OPTIONS ss w-----------}---- (2) Sets the game options (See 6-3-2)

EFFECT TEST =— www -2=2===f-==- (3) Tests the lamp and drive output (See 6-3-3)

SWITCH TEST (4) Tests the Switches (See 6-3-4)

MONITOR TEST —---==-2=====f---- (5) Used for adjusting the monitor (See 6-3-5)

SOUND TEST — wrwwwwn-2="-4---- (6) Used for testing sound and setting volumes (See 6-3-6)

ADS TEST =— wwennnnnnnea fone (7) Displays accumulated game data (See 6-3-7)

ARCHIVE DATA = ww--=--=-===}-="= (8) Displays the Game Data for past 30 days (See 6-3-8)

OTHERS w,

Note: If the steering wheel has not been initialized properly, it may not be possible to select items. If this happens, refer to section 6-4 “Initialization after Replacing Parts”, and initialize the game.
Page 23

6-3-1 Coin Options

Select item (1) "COIN OPTIONS" on the menu screen to set (— \ i hai fae and COIN OPTIONS

related settings. [ DEFAULT IN GREEN ]

Turn the steering GAME COST wheel to select the 1COIN1 CREDIT eeessssssseeeeheeee (a) required item. FREE PLAY OFF i oeeceseceseseeedieeeee (b) Use the 'Trigger' buttons to adjust the

settings. EXIT : PRESS VIEW CHANGE BUTTON

Press ‘View Change’ Ne wy, Button to return to the menu screen.

Note :- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the Coin Options on the screen are set as shown in the following table.

ITEM CONTENTS FACTORY SET

  • Game Cost No of Coins required for No. of credits - - - - - - settable 1-9 1 Coin 1 Credit
  • Free Play Yes/No NO
Page 24

6-3-2 Game Options

  • Select item (2) "GAME OPTIONS" on the menu screen to set the game options and related settings.
  • Turn the steering wheel to select the required item.
  • Press the 'Trigger' buttons to adjust the settings. Standard settings are displayed in green.
  • Press ‘View Change’ Button to return to the menu screen.

GAME OPTIONS [ DEFAULT IN GREEN ]

ID No. 1 LINK 2

PLAY TIME 120 GAME DIFFICULTY NORMAL TEAM COLOUR GREEN SOUND IN ATTRACT ON ATTRACT SOUND VOL 38

EXIT : PRESS VIEW CHANGE BUTTON e@Svee

ITEM DESCRIPTION FACTORY SET

  • ID No For one machine set to 0 and 1 setting from left to right For two machines set to 0 to 4 setting from left to right 0 Left 1 Right
  • Link Displays link condition. For one machine, 2 is displayed. For two machines, 4 is displayed. If data is not received, OFF is displayed, and when corrupt data is received, NG is displayed.
  • Play Time Sets duration of game time from 100, 120, 140, 160, 180 or 300 seconds
  • Game Difficulty EASY (Families & Children), NORMAL (Regular Players), HARD (Maniac Players) Normal
  • Team Colour For one machine set to GREEN and WHITE from left to right For two machines set to GREEN, GREEN, WHITE and WHITE setting from left to right. Green & White
  • Sound in Attract On / Off On / Off On
  • Attract Sound Vol Sets the volume level during Attract Mode
Page 25

6-3-3 Effect Test

  • Select item (3) "Effect Test" on the menu screen to test the lamps and drive output
  • Turn the steering wheel to select the required item.
  • Use the right Trigger Button to activate the test.
  • Press ‘View Change’ Button to return to the menu screen.

EFFECT TEST

LAMP HANDLE + SEAT HANDLE SEAT

TEST: PRESS RIGHT BUTTON EXIT : PRESS VIEW CHANGE BUTTON

J

ITEM DESCRIPTION

  • Lamp The lamps light when the trigger button is pressed
  • Handle + Seat —|Not Used
  • Handle Not Used
  • Seat Not Used
Page 26

6-3-4 Switch

1. Test

and Potentiometers

the menu screen. Select item (4) "Switch Test" on the menu screen to test the switches

Turn the steering wheel to select the required item.

Use the right Trigger Button to activate the test.

Press ‘View Change and Right Trigger’ Buttons together to return to

Va SWITCH TEST

HANDLE RIGHT PEDAL LEFT PEDAL

RIGHT BUTTON LEFT BUTTON VIEW CHANGE BUTTON COIN SERVICE SWITCH TEST MODE SWITCH

EXIT : PRESS VIEW CHANGE BUTTON AND RIGHT TRIG 0000 . 0000 . 0000 .

OFF OFF OFF OFF OFF ON

GER BUTTON

ITEM DESCRIPTION

  • Handle decrease when turned to centre '0000’ is diplayed ‘OK’ is displayed just be’ The numbers increase when he steering wheel is turned to the right and the left. When the steering wheel is in the . (Itis normal for the last digit to be changing). fore the wheel is turned fully left or right.
  • Right Pedal when t ‘OK’ is displayed just be! The number increases when he pedal is released. ( he pedal is depressed. 0000 is displayed is normal for the last digit to be changing). fore the pedal is fully depressed.
  • Left Pedal when tl ‘OK’ is he pedal is releasi displayed just be The number increases when the pedal is depressed. 0000 is displayed ed. (It is normal for the last digit to be changing). fore the pedal is fully depressed.
  • Right Button (Trigger) ON ap| pears when the right trigger button is pressed. ) left Button (Trigger) ON appears when the le! rigger button is pressed.
  • View Change Button On appears when the view change button is pressed.
  • Coin Switch Not Used
  • Service switch ON appears when the service button is pressed.
  • Test Switch ON is always displayed in this test.
Page 27

6-3-5 Monitor Test

  • Select item (5) “MONITOR TEST” on the menu screen to set up and adjust the monitor.
  • Onentering monitor test, the screen will display one of the following test patterns.

GRADATION PATTERN CROSSHATCH CROSSHATCH WHITE WINDOW WHITE WINDOW WHITE WINDOW INTERLACE PATTERN VIEW ANGLE ADJUST VIEW ANGLE ADJUST FULL WHITE GREEN WHITE (H) (M) (L)

(CRT) (PROJECTOR)

  • Use the left trigger button to step forward through the patterns and use the right trigger button to step backward through the patterns.
  • Refer to the monitor manual for monitor adjustments.
  • Press View Change button to return to the main menu.

6-3-6

1. Sound Test

Select item (6) "Sound Test" on the menu screen to test the sound and speakers.

The following screen will appear on the monitor.

( SOUND TEST >

(DEFAULT IN GREEN)

REQUEST SONG No 000 SPEAKER VOLUMES [0-63] FRONT L 42 FRONT R 42 VOICE 35 VIBRATION 63

MESSAGE

EXIT : PRESS VIEW CHANGE BUTTON NX S

Select the required item by turning the steering wheel left or right. The selected item will ‘blink’.

Page 28

Pressing the right trigger button will cause the selected value increase.

  • Pressing the left trigger button will cause the selected value to decrease.
  • Depressing the forward pedal (right pedal) will produce the sound of the song number selected. (Request Song 01 will produce a stereo sound test. Sound will be produced from the speakers in the following order:- Left front speaker, Right front speaker, Both front speakers, seat speaker and finally the seat shaker will vibrate.)
  • Pressing the Viewpoint button will return to the Main Menu.

ITEM DESCRIPTION FACTORY SET

  • Song No Each number up to 256 will produce a different sound. 001 will 000 produce a stereo test
(b) FrontL—|Sets the volume for the front left speaker ~ 00 lowest to 63 loudest42
(c) Front R|Sets the volume for the front right speaker ~ 00 lowest to 63 loudest42
(d) VoiceSets the volume for the seat speaker ~ 00 lowest to 63 loudest35

. . Adjusts the amount of vibration applied to the seat

  • Vibration 00 lowest to 63 highest 63

6-3-7 Displaying and Resetting the Game Data

4. Select item (7) "ADS Test" on the menu screen to view or reset the machine data (book keeping).

There are five pages of data. Press the right trigger button to advance forward through the pages and press the left trigger button step back.

The data will not be lost at power off and can only be reset as described below.

Press the Viewpoint button to return to the Main Menu.

Resetting the Data

1. Depress the right pedal when “RESET DATA” is blinking on page one. The [YES NO] field is displayed.

Use the steering wheel to select “YES”, and then depress the right pedal to reset the data.

6-3-8 Displaying the Archive Data

1s Select item (8) "Archive Data" on the menu screen to view the game data for the last thirty days.

There are three pages of data. Press the right trigger button to advance forward through the pages and press the left trigger button step back.

Press the Viewpoint button to return to the Main Menu.

Page 29

6-4 Initialization after Replacing Parts

Initialization must be performed after replacing the Game PCB, ROMS, or Steering and Pedal Potentiometers. If initialization is not performed, the game will not function correctly.

  • Ensure that the steering wheel is in the centre position and that the pedals are fully up.
  • Slide the Test Switch into the ON position while pressing the service button. Keep the service button pressed until the “ADJUST MODE” screen is displayed. (This will take approx. 5 secs.)

Va

Ne ADJUST

ADCHO 0000 ADCH1 0000 ADCH2 0000 ADCH3 0000 ~\

/

  • | Adjustment is completed if ‘0000’ or ‘FFFF’ is displayed next to “ADCHO”, “ADCH1”, “ADCH2”, and “ADCH8”. It is normal different. or the last digit to be

If the numbers are not ‘0000’ or ‘FFFF’, switch the Test Switch OFF and repeat step 2.

  • Slide the Test Switch off to return to normal game mode.

6-5 Self Test

This game automatically performs a self test each time it is turned on. If there is an error, an error message will be displayed and operation will stop.

Page 30

6-6 Linking Two Machines

1.

2. Ensure that the power is OFF.

Loosen the two pozi head screws retaining the link cover bracket, located next to the mains-in socket on the rear of the machine, and remove the link cover bracket.

Use the supplied link cables to connect each link board. (See Diag.)

ONINTONONINTON
OFFEXTOFFOFFEXTOFF

IN OUT © @

Set the link switches to “ON”, “EXT” and “ON”. (Refer to 6-6-1 (below) “Setting the Link Switches”)

Refit the link cover bracket, passing the link cables through the slots in the cover bracket.

Turn the power to the machine “ON” and set the PCB ID settings. (Refer to Section 6-3-2 “Game Options” item (a).)

6-6-1 Setting the Link Switches

The link switches are for setting the connection between machines or seats.

Setting for one Machine Setting for two Machines (2 seats) (4 seats)

ONINTONONINTON
OFFEXTOFFOFFEXTOFF

IN OUT

Page 31
  • MAINTENANCE

Va In order to prevent injury or electric shock to service personnel, ensure that the MAIN POWER IS OFF before attempting any maintenance.

Before performing any work not described in this manual, be sure to contact your distributor to receive instructions or answers to questions.

~\

Va Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muB der Netzstecker gezogen werden.

Bei Arbeiten, die nicht in diesem Handbuch beschrieben werden, muB vorher der Handler zu Rate gezogen werden, da sonst keinerlei Haftung bei Beschadigungen und Verletzungen Ubernommen wird. J

\

Va S’assurer que |’interrupteur soit sor OFF avant de commencer tout travail de maintenance (localisation d’une panne, réparations, etc.)

Si dans ce manuel il manque une information pour réaliser un quelconque travail, contacter votre distributeur, car aucune responsabilité ne sera acceptée en cas de domage ou de blessure. w

~

  • | & ©] | & O| |b ®@

Assicurarsi che la macchina sia SPENTA prima di incominciare qualsiasi lavoro di manutenzione (guasti, riparazioni etc.)

Se state per iniziare un lavoro non descritto in questo manuale, contattate il vostro distributore per instruzioni poiché non si accetta alcuna responsabilita per danni 0 ferite. > @|| & Varmista, etta laite on kytketty POIS PAALTA ennen tyén aloittamista.

Ota yhteytta maahantuojaan obhjeita varten, jos joudut tekemaan tyétehtavia, joita ei ole esitelty huoltokirjassa, muuten vastuuta vioista tai loukkaantumisista ei ole.

Page 32

> bP BBE B& 7-1 Replacing the Fluorescent Tube, Starter and Lamps

1. Remove the four security screws (M4x16) and remove the glass retaining bracket.

Remove the four security screws (M4X20), from the top, and remove the header acrylic.

Replace the fluorescent tube or starter.

The lamps are a screw fitting. Turn anti-clockwise to remove.

Reassemble in reverse order.

Warning The fluorescent tube may be hot. Take care when handling the tube.
Warning Vorsicht bei der Leuchtstoffréhre, da dieses noch heiB sein kann.
Warning Le lampe fluorescente peut étre chaude, attention lors dela manipulation.
Warning La lampada fluorescente potrbbe essre calda, attenzione a maneggiarla.
Warning Varo kuumaa loisteputkea.

Security Screw (M4x20)

Security Screw (M4x16)

Glass Retaing Bracket

Page 33

7-2 Replacing the Viewpoint and Credit Available Switches

1. Remove the four security screws (M6x25) and washers from the top of the play panel and hinge the play panel forwards.

Remove the lamp/switch assembly by pulling it away from the switch body. Replace the switch or lamp.

Note: When replacing the switch ensure that the wires are replaced to the correct terminals

7-3 Removing the Steering Wheel

1. Carefully remove the round hub cover by gently levering out using a flat blade screwdriver. (Lever at different points around the hub cover to remove evenly.)

Disconnect the connector. (Take care not to strain the wires when separating the connector.)

Remove the three button head screws and remove the steering wheel.

7-4 Replacing the Trigger Button

1.

2.

3. Remove the steering wheel. (Refer to section 7-3, above.)

Remove the four pozi head screws and remove the switch cover.

Replace the switch.

7-5 Replacing the Steering Potentiometer

1. Remove the four security screws (M6x25) and washers from the top of the play panel and hinge the play panel forwards.

Remove the two pozi head screws and remove the potentiometer bracket complete with potentiometer and gear wheel.

Loosen the grub screw and remove the potentiometer.

When refitting the potentiometer ensure that the locating lug engages in the hole in the bracket and that the grub screw engages on the flat of the potentiometer shaft.

Note: Ensure that the wires are reconnected to the correct terminals.

5. After the play panel has been refitted ensure that the game is reinitialized (Refer to section 6-4)

Page 34

7-6 Removing the Pedal Assembly

  • Remove the four security screws (M6x25), flat and spring washers and withdraw the pedal assembly from the front of the machine. (Take care not to strain the wires.)
  • Disconnect the connector and remove the assembly.

7-7 Replacing the Pedal Potentiometer

  • Remove the pedal assembly. (Refer to section 7-6, above.)
  • Loosen the grub screw and remove the gear.
  • Replace the potentiometer.
  • When refitting the potentiometer ensure that the locating lug engages in the hole in the bracket and that the grub screw in the gear engages on the flat of the potentiometer shaft.
Note: Ensure that the wires are reconnected to the correct terminals.
  • After the pedal assembly has been refitted ensure that the game is reinitialized (Refer to section 6-4)
Page 35
  • PARTS

Item Description Part No

1Hantarex 28" Polo Monitor84000026
2Trigger Switch60000013B
3Steeering Assembly88800070
4View Change Button Assembly60200708
5Credit Available When Lit Button Assembly60200215
6Side Decal - RHS40000375
7Single Pedal Assemby W/Pot88800098
8Swivel Castor 75mm59000005
9M16 Adjustable Foot88300079
10Side Decal - LHS40000374
nlFront Glass31000024

Not Shown | Potentiometer - Pedal & Steering 88800053

Page 36

Description Part No

Header Acrylic 30000233

2|Flurescent Tube 4ft64500014
3{Starter63000000
4|E14 Golfball Lamp - 240vAC/25watt64000084
5|E14 Lamp Holder64800003
Page 37

Om Cal

Item Description Part No

1Speaker Plate Black - LHS88300603
2Speaker Plate Black - RHS88300604
3Loudspeaker - 4%c' 20watt62000006
4Seat - Dark Blue46000046
5Decal - Seat Rear40000376
6Loudspeaker - Bass Shaker62000076
GDecal - Namco Base40000036
8M16Adjustable Foot88300079
9Swivel Castor - 75mm59000005
Page 38
  • SCHEMATIC

Seaatietieieineiaieateaiatedieteteten 7

1HEADER ASSEMBLY:

' a} Beown ' FLUORESCENT ASSEMBL’ 22 | SRNL i T I i

'14 SLO BLOoe >=

BROWN :

1) FLUORESCENT ASSEMAL', GRUAELSeLewtit TTanteal
Iele y stueen (ETE

Sen (Sweater = i ernie LE: in L 68 Woofer = I ha sown

'pre eeeI EQUALIZER A

| @ | @ @ L+t I 230v 254 £14 LAMPS MEL I BROWN

![SO GaELeenI
'2.2 Rie5'
Leensoca2
iainELI

a4

po------eT hss aie Sea!

ipininiananaiel a BUTT and

Iweap 1} Beht!
Geen ete eeerti
!Bue STs PALE—=j
iGre 3, 4 PALEeen EI caer
jwanStk H He ed =1
| HANTAREX 28°me STsTi

L =

' Pot) MOTORost BROWNBUTT Rabe aie =
anatena

Buu a3 phe Sper =

Hal'cesT 7ELROD CPT BanE SpkE =i
| [LooeGRNCVEL,L ooL

Torta eeD

!Beart} RED.ns TT anole EL

BLUE Tete

IGeen [2 ye} SEHeen —T lend

gene ace SE Sue

x!Greta Ta PALLeg ee
Bs| HANTAREX 28”LUEjoofer =
zePOLO MONITORSete te Htie —+ $18 (waster
a'RHSuEber tend
='AC Live] PTT} BROWNo78

! Ferrite | BLK. io 10

weep st} BLeux=
\cree Ss} BEtons Wetes
LstunHSHe siay
~ oeee'

Rea

a» 42 [Green
cSota OB= fslue

to + eyne é ical é

fo 4

a gl| fgaetpsec REDTE Oe
g 3BEESe Reeee {ran
gal| EE“Sle Te Trenjeu

ean eye te pee

& PeUPRCrate Lae

in Lage

2 C2\Beso acackHe
© QePacage ——~ca
aIGral_2 8:ae
qBSae
dTin
'aestees

F [RED ———~

Flisupe eredTT lon
qeats1al

4 fRED ~~

4IaosiiYeLLY 9-9 [lew

| SWITCH Sage te} BACK

gg§ 1 MODEes SS tarace,!Beg TBEI
Egg5=\mej
S== | POWERbadBLACKI373\
[1}= | SUPPLYbod | 5sing Oued 14eereDe
apes HE aback,iGraf 515TO Rg a=
z !Gag [erTia}BLACK,iBeate eT2 (era n=
8§CNene a=
5aatae!Ege TT214 fond
d4'Gal ene'tata=3
FeIsepelo.
ggu a3 WELLOW'Deane tsots
|!Heya Ta YELLOWL7T
Ised eci

vee es 5 ' SS 22 PCB.

ae besos ==

Page 39

r SEAT ASSEMBLY I BLACK 4

‘WHITEoFI
BEDaveI
FINErarBASS SHAKER

STs cewvver_ [STS i

i I —————— SEAT SPEKR |

1csi

' i

pecker epwiureL--5 ee 4

Speaker = [2 Te [BLACK

1eaua7] LHS

BLU/BLK

!-=e BOR veraU] PLay PANEL
4 PCBI3Ta Wevaenapp)SPEAKERS
arecest“{[] ars

MP CONTROL BOARD! ~ I Tove = Te 7 RR Cte — WOE ere RDN STS = NEL 4

EWEmntaS
sosee eeTRIGGER -RHS

eI RE wer ETE 77 cara

Tovearte BROWN _pen TSS

Soke = tut [35 Be ALE fe Ts Rewtrat — Tafa —— | triccer - Las t

TET ESS SOLE

Sse2 Conrail 74Renz
‘WEITEZECUE.°STEERING
BLACK313POTENTIOMETER

ABLE pO rewpaRE Lane TTT eos tame [ete Boa — ate oater Contrat | STS — ena ete

+t—VIEW CHANGE
Stsa4LHS 7 RHS

I Tagger Lang ES Teh Trigger Lamp CTS] it 10

ieyteimd
ETeTEPEMERSBEDan
tteHT ZGEELi
Tra p15RusaTEELlPEDALI
|SRUAEL aTFORWARD
Viewpoint Sof T ty yeuuee—_'

Triage EPs 3 PRUE

espaBhacke+elLPepa!
515GENEL 1373BACKWARD |

Gra 717 aL ____. ' at tLe 4 I CREDIT AVAILABLE ~ RHS

1roa _anearen

i ee

favais ets wHIZELOL!ataera
ars+TesT ~ Hs) | |7rHByALL
ia 3aBEUaELETSsel],4ata et

Anver| STS £

Facelarator FW Epo WHEGENPua +eSERVICE = Lx |:—
Hecslerator By [7 +7 1WHI/ORGYEL BLK@oh
BLEHe1ate
Andy STraed|ete
ateonilog14
THCOUNTERCREDIT AVAILABLE — LHS
1212i1po-----tH=--4 Fh --4
Imu!'Ls crei
erdeep ITTotsTest = RHS| | |LL Renateee
Teste) 2SReBETaTSBot]!(71+‘Spa LEEINKSe
Fev, aTSERVICE —_RHS) |!EYALa
carer Sirar'\an

Graf +6. ELLOD

ell TTate!BLACKaate
Tania 8IIaerot
tan ep StSiriw
iLoieee 4seuvet149aH
iLIsis
iaGREY /BLACK,ais
sSSEMBLY!SS 11S
IT4 [ie
JHlCOIN DOOR ASSEMBLY gfe

--- ae cay I a1 ' CASHFLOW-CREDIT DISPENSE | Lf 22 ee a

Page 40

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 41

eee epi td a SEAT ASSEMBLY

BLACKrh!
‘WHITE1\

ai 23 \

PINCralBASS SHAKER

STs cave TE \ H I a SEAT SPEKR | 1 '

aII
1L4

peoker spr apeuuTe | | PP rrr rrr ‘Speaker —[# Te [aLack

_1oat“f( Las
I~ete eer<UL} Play PANEL
TZER] AHP: PCR|a$43 EU REDaif SPEAKERS

toprcssstsss Ss

Tigsls|] Ris

ILaMP CONTROL BoarD! I \ \ Covet [1] Cove Wee.

nee|
=eleTRIGGER -RHS
IlA= Tet 6ta 13
|Heeseentsx
\RE Tut [9AE Ts Ts.+
iT Neutral = Ta[i| rerecer - Lus

IT \ i I \ I FET PL ' igeg) TSH Cantrell 33

1Soke Contre a LUAen=
'1‘WHITE 7CUEyoSTEERING
\\BLACK213POTENTIOMETER

--L--------J

\ oy

Ena eTcn(0;

Hit Lane ete canal HE

roofer Control argPINEMew CaiGe
taATa TaLHS / RHS

é18 Trigger Lana Rate peN Tiger Cans C133 i ITH p------------- ile 7

aaotfo

ati

Grol [1518pLack fo +ePEDALj
|SRUAEL aTFORWARD

Viewpoirt Sw[ 1 17 JPNK/RLK __ '

‘Tringer RPE pe BeBEDee\

“Trigger Lf a3 BLUE

sesataBageyepenal|
315GRAVEL} 374BACKWARD |
ANGaal 717 Lk!

Groff Jd I CREDIT AVAILABLE ~ RHS

\Po Se 41FL
mivespr yeepf16seae
eget TELIRNVEEL
nelfeTest = uns] |aaSvat
NewSRUBE TSsot] |ottZBL
aDVec |S TS Fe.7 ol*
Receraeor FE€ HHTaSERVICEors
accelerator BW[ 77 [MAZURELBE Teiete
ADGnel| 8 TE$48oe
ate|teks

EE}

|counTeR | |CREDIT AVAILABLE - LHS
I\poccct pes 4 ripoca
\\L
acreyan
_teTest - eas] | 1Lavaome
TestDB aTs3 ot | 1T+a5 HEPINK22
anSERVICE - RHS| |1—sts
Counter SIP616o|I8 $
aml|anaTaa
CoinaTjlEneSte
Calin 2|GEN/YELFRE]Topi
Me ee ae 444a iT

\ 1313

aGREY/BLACKasl

2 PCB ASSEMBLY 1515 T 46 [16

oeICOIN DOOR ASSEMBLY Hate

I coi ! CASHFLOW-CREDIT DISPENSE |

Los2a