CATHODE RAY TOMES

Street Fighter EX

Street Fighter EX (Europe 961219) (Capcom / Arika, 1996) · Manual · 18 pages · 14 sections · original scan

Page 1

@ ARIKA CO., LTD. 1996 © CAPCOM CO.,LTD. © CAPCOM U.S.A, INC. 1996 ALL RIGHTS RESERVED.

OPERATORS MANUAL

/N\ WARNING

This game is for use in the United States of America and Canada. Sales, export or operation outside of these countries may be constructed as copyright and trademark infringements and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.

CARCOMY COIN-OP, INC. 3311 N. Kennicott Avenue Arlington Heights, Illinois 60004 Phone: (847) 797-6192 PM00185-KIT Fax: (847) 797-6306 012097

Page 2

CAP@OM coin-op, inc. STREET FIGHTER EX™

THANK YOU FOR PURCHASING STREET FIGHTER EX™ WE INVITE YOU TO USE THE FOLLOWING MAILING ADDRESS, TELEPHONE OR FAX NUMBER FOR PARTS OR SERVICE INFORMATION CONCERNING THIS GAME:

CAPCOM® COIN-OP, INC. ATTN: FIELD SERVICE - VIDEO PRODUCTS 3311 N. KENNICOTT AVENUE ARLINGTON HEIGHTS, ILLINOIS 60004 PHONE: (847) 797-6192 FAX: (847) 797-6306

THE SERIAL NUMBERS OF YOUR GAME ARE LOCATED ON THE PRINTED CIRCUIT BOARDS AS SHOWN BELOW. PLEASE HAVE THESE SERIAL NUMBERS AVAILABLE WHEN CONTACTING US FOR SERVICE INFORMATION.

PLEASE RECORD THE PC BOARD SERIAL NUMBERS HERE:

  • LOWER PC BOARD - SOLDER SIDE: AAMA SERIAL NUMBER:
  • LOWER PC BOARD - COMPONENT SIDE: CAPCOM SERIAL NUMBER.
Page 3

CAPCOM co-op, inc. STREET FIGHTER EX™

TABLE OF CONTENTS

Warranty Information

Kit Inspection I

Kit Installation Preparation Installation Marquee Control Panel Components 2. Cabinet Decals wunnn Wiring Control Panel Test/Volume Bracket Speakers Q-Sound Modification PC Boards AUR RW

Game Adjustments Volume Control Stereo / Monaural Test Menu Accessing the Menu How to Select an Item Closing the Menu Menu Item Descriptions Configuration Menu System Configuration Game Configuration CHOIADDAADAUUY

Reference Information JAMMA Connections 10 Auxiliary Cable Connections 10

Template : Control Panel Drill Hole(s)

CAUTION

Please read the following instructions to keep the PC boards in good condition:

@ Do not drop or bump the boards. @ Do not spill any liquids on the boards.

DISASSEMBLING THE BOARDS OR REMOVING STICKERS MAY CAUSE THE TERMINATION OF YOUR REPAIR WARRANTY.

Proprietary and confidential information, aot to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 4

CAPCOM co-op, inc. STREET FIGHTER EX™

LIMITED PRODUCT WARRANTY (APPLIES TO DOMESTIC SALES ONLY)

CAPCOM® COIN-OP, INC. (Seller), warrants only to the initial purchaser of its products, that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

A. Printed Circuit Boards: Ninety (90) Days B. Electronic and Mechanical Components: Ninety (90) Days

No other part of Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from seller to its authorized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

A. Seller is notified promptly upon discovery by buyer that stated products are defective;

B. Such products are properly packaged and then returned, prepaid to Seller's designated plant.

This warranty does not apply to any parts damaged during shipment or handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a CAPCOM® COIN-OP, INC. product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

IMPORTANT NOTICE

THIS SHIPMENT HAS BEEN CAREFULLY INSPECTED AND PROPERLY PACKAGED BEFORE LEAVING THE FACTORY. WE CANNOT ASSUME RESPONSIBILITY FOR BREAKAGE THAT MAY OCCUR DURING TRANSPORTATION OF THE GAME. IF THIS GAME IS DAMAGED UPON RECEIPT FROM THE CARRIER, IMMEDIATELY NOTIFY THE CARRIER AND FILE A DAMAGE REPORT.

ii Proprietary and confidential information, aot to be disclosed or copied without the express permission of CAPCOM® COIN-OP. INC.

Page 5

CAPQOM” co-op, inc. STREET FIGHTER EX™

KIT INSPECTION

Check that all of the following parts have been shipped with your kit. If any parts are missing, contact your distributor immediately.

SFE1000 KIT PARTS LIST

PART NO. DESCRIPTION

SFE1400 Assy, PCB, PSX System, Street Fighter EX 13-0154 Standoff w/Screw, PCB Mounting $C00104-05 Screw, Wood GE1200 Monitor Card AW00242 Marquee, “Street Fighter EX” PL00376 Plex, Marquee, Clear, 27.0 x 9.0 x 1/8” AW00147 Decal, Cabinet Side AW00216 Overlay, Control Panel AW00240-3 Decal, AAMA, Strong, Violence, Animated AW00243-1 Decal - Top, Game Play Instruction, SFEX AW00243-2 Decal - Bottom , Game Play Instruction, SFEX AW00243-3 Decal, Joystick & Button Switches, SFEX PM00185 perators, SFEX 03-0104 Harness, Stereo Speaker 03-0066 Cable, Auxiliary GE2030 Joystick, 8 Way Switch, 1-Player Start Button (White) Switch, 2-Player Start Button (White) Switch, Button (Red) Switch, Button (Blue) Switch, Button (Green fog gg erg era greg reg eg teg eg ieg tea eaisy(euiegieap-ap-aiey

‘ation, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP. INC. Proprietary and confidential

Page 6

CAPEOL’ coin-op, INC.

KIT INSTALLATION

WARNING:

MAKE SURE ELECTRICAL POWER TO THE GAME IS OFF BEFORE STARTING THE KIT INSTALLATION.

PREPARATION

  • Disconnect and remove the old printed circuit board(s) from the cabinet.
  • Remove or open the control panel, and disconnect and remove the buttons and joystick(s) from the control panel.
  • Remove any covering from the control panel overlay, and then remove the control panel overlay.
  • — Place the Drill Hole template over the control panel to determine where any new holes should go. Center punch any needed new holes on the control panel.
  • Cut out the new holes using a 1-3/16" hole saw.
  • If there is an additional control panel cover, Figure 1 (such as plastic or lexan) that will be utilized, cut any additional holes using the same template. *Cover is not included in the kit.
  • Plug up unused holes with a wood dowel (1-1/8" diameter) and sand any rough edges.

INSTALLATION

Marquee Installation

  • Remove the marquee plexi glass, marquee overlay, and the cabinet graphics.
  • — Install the new marquee and replace the plexi glass. Clear plexi glass is included in “Full” kit.

Control Panel Overlay Installation (See Figure 1)

  • The control panel overlay in the kit is oversized to accommodate most control panel sizes. Center the overlay on the control panel, leaving some excess material at the edges.
  • Remove the protective backing from the overlay and press it down on the control panel, keeping it properly aligned. Press it down firmly, smooth out any bubbles, and press it over the edges. STREET FIGHTER Ex™
  • Trim any excess from the overlay. Place the drill hole template on top of the overlay, aligning it with the joystick holes. Pierce through the overlay at each control panel hole. Then, cut away overlay material covering the joystick and button holes. Remove the template and clean off the overlay.
  • Peel off the backings of the 6-button and joystick decals, align over the control panel holes, and press in place on the overlay (refer to the drill hole template for proper placement). Using a knife, trim material from the center hole of the joystick decal.
  • Install the control panel cover, Figure.1. (if required).

Overlay (Trim to size)

Control Panel

Figure 1: Overlay Installation

Reassembly of Components

  • Notice that there are two white buttons. See Figure 2. The WHITE buttons are START buttons. Install the PLAYER ONE button on the top left-hand side of the control panel, and the PLAYER TWO button on the top right-side of the control panel.

Co = 2 Player 1 Player 7 2 Play @ a yr OY

Figure 2: Start Buttons

2 Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 7

® CAPEOM coin-op, inc.

Red Green Blue Puy Red Green Blue ‘Gly

qos

Red Green Blue Red Green Blue

Buttons S a 34 y

Retaining ~ Switches —— ZF eZ eo

Figure 3: Control Panel Buttons and Switches

  • Install all buttons and retaining rings on the control panel as shown in Figure 3. Install two RED buttons to the immediate right of each joystick, install two GREEN buttons to the right of the red ones, and install two BLUE buttons to the right of the green ones.
  • Install the switches on the buttons as shown in Figure
  • Orient the switches so that when a button is pressed, the ted contact on the switch is depressed.
  • Install the joysticks on the control panel as shown in Figure 4.

Figure 4: Joystick Installation STREET FIGHTER EX™

CABINET DECAL INSTALLATION

  • | Remove monitor glass and install monitor card
  • —-Peel-off the backing to the instruction decals and place on both the top and bottom of the monitor card. (See Figure 5). Also, apply the cabinet decals to both sides of the cabinet.

MARQUEE,

MONITOR CARD

Figure 5: Cabinet Decal Installation

CONTROL PANEL WIRING

NOTE: All switch wires used in this game must be wired to the normally-open connection on the switches. Each switch requires a ground wire on the common connector and the appropriate control or switch wire on the normally-open connector of the switch.
  • Reconnect the existing JAMMA connectors to the control panel according to the chart in Table 1.
  • Connect the Player 1 and the Player 2 KICK buttons to the auxiliary cable harness as shown in Figure 6. Make the connections according to the chart in Table 2.

To PC Board Connector cN2

To Control Panel Button ‘Switches

Figure 6: Auxiliary Cable Harness

Proprietary and ‘not to be disclosed or copied without the express permis of CAPCOM® CO! we

Page 8

CAP@ON co-op, inc.

TEST/VOLUME BRACKET WIRING

  • An optional Test/Volume bracket (see Figure 7) is available through your local CAPCOM distributor (Part number 03-0050). Your cabinet may already contain this bracket. When installing, the bracket should be mounted. inside the coin door and on top of the cash box for easy access.
NOTE: Only the Test switch is used for this game; the Volume Up/Down switches are disabled. Volume adjustments must be made through the volume control knob located on the PC board.

uP t VOLUME

Figure 7: Test Bracket

Wiring of the Test Bracket requires connections to the main JAMMA harness as shown in Table 3:

LEAD WIRE | SWITCH CONNECTS COLOR FUNCTION To VOLUME-UP_| NO CONNECTION BLACK VOLUME- | NO CONNECTION DOWN. COMMON _| NO CONNECTION BROWN | TEST __| JAMMA “15”

BLACK GROUND JAMMA or “B”

or “e” or “f” or “1” or 2" or “27” or “28”

Table 3: Test Bracket Wiring Chart

SPEAKER WIRING

24a. If you are converting a cabinet that is not equipped with CAPCOM® Q-SOUND, the leads from the speaker harness (supplied with this kit) must be wired to the cabinet speakers according to the Table 4. STREET FIGHTER EX™

LEFT (+) LEFT (-) RIGHT (+)

Table 4: Speaker Wiring Chart

24b. If you are converting a cabinet that is equipped with CAPCOM® Q-SOUND, you may elect to wire directly to the cabinet speaker terminals, as shown above, or you can obtain the same result by performing the following modification (see Figure 8):

  • Disconnect the speaker harness connector from the Q-SOUND board at location CB8.
NOTE: EXTERNAL Q-SOUND POWER AMPLIFIER MUST DISCONECTED WITH THIS PSX SYSTEM PCB.

ii) Install a 4-pin, 0.156 inch diameter header connector (not supplied with this kit; purchase locally) onto the speaker harness connector.

iii) Insert each wire lead from the supplied speaker harness to each corresponding pin from a 4-pin, 0.156 inch diameter female connector (not supplied with this kit: purchase locally).

iv) Push the female connector and the header connector pins together.

  • Your cabinet is now equipped to receive stereo sound from the PC board.

TO CABINET SPEAKERS.

EXISTING ‘SPEAKER HARNESS CONNECTOR

TO nee 4PIN PC aa HEADER eae CRO CONNECTOR 4 5) Aun FEMALE oe NM CONNECTOR

  • SUPPLIED , a SPEAKER HARNESS

Figure 8: Q-SOUND Modification

Page 9

CAPCOM’ co-op, INC.

PC BOARD INSTALLATION

  • Install the four (4) mounting standoffs to the underside of the PC board by securing with the supplied machine screws. Then, fasten the PC board standoffs to the control panel shelf with wood screws, as shown in Figure 11.

wooo scREW

  • —“—_ STANDOFF 1

Figure 9: PC Board Mounting

PC BOARD WIRING CONNECTIONS AND ADJUSTMENTS

  • Connect the JAMMA harness connector to the edge connector located on the bottom PC board (see Figure 10).

AUXILIARY CABLE, STREET FIGHTER EX™

/N\ WARNING

Improper installation of the JAMMA harness connector to the PC board connector will cause damage to the PC board.

  • Attach the auxiliary cable connector to the top PC board at location CN2 (see Figure 10).
  • Attach the speaker harness connector to the PC board at location CN504 (see Figure 10).
  • Check that the mode switch, on the lower PC board, is set to “STEREO” (see Figure 10).
  • Check that all 4 positions of the DIP switch are set to OFF (see Figure 10).
  • Power-up the game and adjust the speaker volume by turning the Volume Control knob clockwise to increase volume, or counterclockwise to decrease volume (see Figure 10).
  • Set all operator adjusTable options by pressing the TEST switch. Follow the instructions under the TEST MENU section of this manual.

Figure 10: PC Board Wiring Connections & Adjustments

Proprietary and confidential information, not (0 be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC. w

Page 10

CAPELLI con-or, INC. STREET FIGHTER EX™

TEST MENU

The test menu allows you to test various functions of the game and configure settings used in the game. These items include input devices such as joysticks, buttons and coin mechs, output devices such as monitor, speakers and meters. Through the Test Menu you can also access the Configuration Menu, where you can change the settings of the game.

  • ACCESSING THE TEST MENU

| INPUT + Fora CAPCOM® cabinet or a converted cabinet OUTPUT with a test switch: . SOUND Make sure the game is on. Open the coin door, find the . COLOR i i « ” ” BOT CROSS HATCH location of the test switch, and Press Test”. The screen ” GAME DATA shown left will appear on the monitor: . CONFIGURATION . MEMORY CHECK . i ii itch:

* SAVE & EXIT For a cabinet without a test switch: ;

. EXIT You need install “Test Switch”. Refer Page 5. for details.

SELECT 1P UP OR DOWN START 1P START & SHOT1 2. HOW TO SELECT AN ITEM . + Use the PLAYER 1 JOYSTICK to move the arrow in front of the desired item and press the PLAYER | PUNCH LIGHT button. Player 1 Joystick Player 1 Start * To retum to the test menu, push the PLAYER /

START and PLAYER 2 START buttons simultaneously.

  • CLOSING THE TEST MENU To close the Test Menu, highlight “9. EXIT” and push the PLAYER I PUNCH LIGHT button. Player 1 Shot 1 Player 1 Shot 2 vieot (Punch Light) (Punch Middle)

° The test menu will always appear on the screen:

  • After you exit the “7. CONFIGURATION MENU” and
  • After the memory is tested from the menu, “8. MEMORY CHECK”.
  • TEST MENU ITEM DESCRIPTIONS

INPUT Used to test all the input switches, such as joysticks and buttons. The “0” changes to a “1” as the button is pushed or joystick is moved. Check connections and switches in case the “0” doesn’t change to a “1” when depressed or moved. OUTPUT Used to test the coin meter and the coin lock. SOUND Select a code of SOUND or VOICE with the PLAYER / JOYSTICK. Push the PLAYER | PUNCH LIGHT button to hear the sound of the selected code. COLOR Shows color bars of red, green, blue, and white. Adjust RGB and brightness to obtain the optimum color balance and solid black background. DOT CROSS HATCH Used to test the screen size, focus and distortion. GAME DATA Coin meter and playtime information will be displayed. CONFIGURATION Used to change the game play settings. Refer to the CONFIGURATION MENU section. MEMORY CHECK Used to test memory. “OK” appears when each block of memory passes test, “NG” appears in case of malfunction. If “NG” appears, repeat the memory test and wait for the “OK” message. Contact your distributor if “NG” still appears. EXIT Select this item and push the PLAYER I PUNCH LIGHT button to return to game play mode.

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 11

CAP@ON co-op, inc. STREET FIGHTER EX™

CONFIGURATION MENU

The Configuration Menu is used to change various game settings such as level difficulty, credits, sound configuration, etc. These settings are stored in memory on the PCB rather than DIP switches. The Configuration Menu is divided into 2 sections. In the SYSTEM section, you can change credits, sound, and coin door configurations. In the GAME section, you can change the play difficulty level and duration of the game.

  • ACCESSING THE CONFIGURATION
  • CONFIGURATION MENU MENU

+ SYSTEM . From the TEST MENU, move the arrow to “7. GAME CONFIGURATION” and push the PLAYER | PUNCH LIGHT button. The screen below will be displayed. A . DEFAULT description of each option is explained in the Table below.

. SAVE & EXIT

SELECT P UP OR DOWN START P START & SHOT1

SYSTEM Select this item to change settings for credits, monitor flip, sound and coin door configurations. GAME Select this item to change difficulty level, damage level, time count speed, maximum number of rounds and event type. DEFAULT Use this item to restore configuration settings to the original factory values. Press the PLAYER | START and PLAYER | PUNCH LIGHT buttons at the same time to select this option. SAVE & EXIT Use this to save new configuration settings and exit to the Test Menu. The message “SAVING NEW CONFIGURATION IN EEPROM” will appear while the new settings are being saved. DO NOT turn power off to the game until “SAVING” is complete and the Test Menu reappears

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC

Page 12

CAP@OM* co-op, inc. STREET FIGHTER EX™

SYSTEM CONFIGURATION

CHANGING THE SYSTEM CONFIGURATION 7-1. SYSTEM CONFIGURATION SETTINGS

>1. a MODE 2 COINS 1CREDIT . CHUTE TYPE 2 CHUTES SINGLE

” CONTINUEONuMove the PLAYER I JOYSTICK up or down to highlight the
. DEMO SOUNDONdesired option. Once the option is highlighted, move the
: Se MODEMONAURALPLAYER | JOYSTICK left or right or press the PLAYER |

PUNCH LIGHT button to select.

SELECT OPTION =1PUP OR DOWN MODIFY SETTING =1P LEFT OR RIGHT = 1P SHOT1 OR SHOT2

SYSTEM CONFIGURATION ITEM DESCRIPTIONS

  • COIN MODE SELECT THE CHARGE PER PLAY.
  • CHUTE TYPE SELECT THE NUMBER OF PLAYER(S) AND COIN CHUTES. 1 CHUTE SINGLE: WITH THIS SETTING, EITHER PLAYER CAN START THE GAME. 2 CHUTES SINGLE: TWO PLAYERS USE ONE COIN CHUTE AND PLAY AT THE SAME TIME. THE PLAYER WHOSE COIN WAS PUT IN FIRST STARTS THE GAME. 2 CHUTES MULTI: TWO PLAYERS USE TWO COIN CHUTES AND PLAY SEPARATELY. THE GAME STARTS FROM THE SAME SIDE AS THE COIN CHUTE WAS USED.
  • CONTINUE USED TO SET THE CONTINUOUS PLAY.
  • DEMO SOUND TURNS ATTRACT SOUNDS ON OR OFF.

‘5. SOUND MODE SELECT STEREO OR MONAURAL FOR USE WITH YOUR CABINET. :

NOTE: STEREO SHOULD ONLY BE SELECTED WHEN THE CABINET SPEAKERS HAVE BEEN CONNECTED TO THE GAME PC BOARD AT LOCATION CNS04. EXTERNAL Q-SOUND POWER AMPLIFIER IS NOT USED FOR THIS GAME. (SEE PAGE 6 FOR DETAILS) TO SAVE THE SETTINGS AND RETURN TO THE CONFIGURATION MENU, HIGHLIGHT THIS ITEM AND PUSH THE PLAYER | START BUTTON.

SYSTEM CONFIGURATION OPTION SETTINGS

3 CREDITS 4 CREDITS 5 CREDITS 1 COIN 2 COINS 8 CREDITS LCREDIT 5 COINS 1 CREDIT 9 COINS 2 COINS START 1 CREDIT 1 COIN CONTINUE

  • CHUTE TYPE 1 CHUTE SINGLE 2 CHUTES SINGLE

b OFF

  • SOUND MODE MONAURAL
NOTE: FACTORY SETTT.

[Proprietary and confidential information, aot to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 13

CAP@OM’ coin-op, inc. STREET FIGHTER EX™

GAME CONFIGURATION

CHANGING THE GAME CONFIGURATION 7-2. GAME CONFIGURATION SETTINGS

> 1, GAME DIFFICULTY 2, DAMAGE LEVEL Move the PLAYER / JOY: ighli

  • TIMER COUNT SPEED SLOW[.2.] FAST ‘STICK up or down to highlight the
  • MAX ROUND (CPU) 3 ROUNDS
  • MAX ROUND (VS) 3 ROUNDS 6. A desired option. Once the option is highlighted, move the PLAYER | JOYSTICK left or right or press the PLAYER | EVENT OFF PUNCH LIGHT button to select. EXIT

SELECT OPTION P UP OR DOWN

MODIFY SETTINGS LEFT OR RIGHT

=41PSHOT1 OR SHOT2

GAME CONFIGURATION ITEM DESCRIPTIONS

  • DIFFICULTY SETS THE DIFFICULTY LEVEL.
  • DAMAGE LEVEL | SETS THE OFFENSIVE POWER LEVEL
  • TIMERCOUNT _| SETS THE SPEED OF THE COUNTDOWN.
  • MAX ROUND SETS THE NUMBER OF ROUNDS PER MATCH FOR “VS, CPU"
(Vs. CPU)1 ROUND:WINNER OF A SINGLE ROUND WINS;

3 ROUNDS: WINNER OF 2 OUT OF 3 ROUNDS WINS; 5 ROUNDS: WINNER OF 3 QUT OF 5 ROUNDS WINS.

  • MAX ROUND ‘SETS THE NUMBER OF ROUNDS PER MATCH FOR VS. PLAYER”:
(VS. PLAYER)1 ROUND:WINNER OF A SINGLE ROUND WINS;

3 ROUNDS: WINNER OF 2 OUT OF 3 ROUNDS WINS; 5 ROUNDS: WINNER OF 3 OUT OF 5 ROUNDS WINS.

  • EVENT TURNS ON EVENT MODE. USEFUL FOR CHAMPIONSHIP TOURNAMENT. OFF: NORMAL SETTING. SETS THE MODE TO NORMAL OPERATION. ON: | MATCHES PLAYER WITH ONE CREDIT. A WIN OR A LOSS RESULTS IN GAME OVER. (CONTINUE IS NOT AVAILABLE). RETURN TO THE CONFIGURATION MENU.

GAME CONFIGURATION OPTIONS

  • DIFFICULTY 3
  • DAMAGE LEVEL
  • TIME COUNT 1 2 3 4
  • MAX ROUND 3 3
(cPu)ROUND[GIRDERROUNDS
  • MAX ROUND D 3
(vs)ROUND[RXQSDSROUNDS
  • EVENT OFF
NOTE:

[Proprietary and confidential information, not to be disclosed or copied without the express permission of CAPCOM® COIN-OP, INC.

Page 14

° CAPCOM" coin-op, ine.

*WIRE COLOR SOLDER SIDE STREET FIGHTER EX™

COMPONENT SIDE *WIRE COLOR GND

GN! iD

+5 VDC

.C.

VIDEO GREEN

VIDEO SYNC

VIDEO GROUND.

TEST MODE

2 PLA’

VIOLET/BLACK

ee ee es ee PT esPEAKER (4

YER - COIN

: D ACHR ee er rem amon we 1 PLAYER - COIN

1 PLAYER - START

1 PLAYER - UP.

1 PLAYER. - DOWN.

1 PLAYER - LEFT

1 PLAYER - RIGHT

: A WHITE/BLACK.

WHITE/BROWN

WHITE/ORANGE 1 PLAYER - PUNCH LIGHT WHITE/YELLOW 1 PLAYER - PUNCH MIDDLE WHITE/GREEN 1 PLAYER - PUNCH HEAVY. WHITE/BLUE iM NIC

NIC

GND

Table 1: JAMMA Wiring Connections

  • Wire Color Note: Wire colors shown are according to the AAMA-AMOA Standard for wire color assignments; your harness may contain different colors than shown above.

WIRE COLOR CONNECTOR ODD ROW

NIC NIC NIC NIC PLAYER 2 KICK HEAVY NIC NIC PLAYER 1 KICK HEAVY PLAYER 1 KICK MIDDLE PLAYER 1 KICK LIGHT PURPLE/YELLOW

GRAY/YELLOW PLAYER 2 KICK LIGHT PINK/YELLOW PLAYER 2 KICK MIDDLE NIC NIC NO CONNECTION NO CONNECTION GRAY/YELLOW

BLACK/WHITE NO CONNECTION PINK/YELLOW

PLAYER 2 COMMON PLAYER 1 COMMON BLACK

Table 2: Auxiliary Cable Wiring Connections

10 [Proprietary and confidential information, not 19 be disclosed or copied without the express permission of CAPCOM® COIN-OP, ING,

Page 15

1-3/16" DRILL FOR PLAYER HOLE

1-3/4" DRILL FOR JOYSTICK HOLE

TRIM LINE (TYPICAL)

1-3/16" DRILL FOR BUTTON HOLES i

!

aml

oan)

i} \ ' t

. CAPCOM , INC. 3311 NORTH KENNICOTT ROwma ARLINGTON HEIGHTS ILLINOIS 60004

DRILL TEMPLATE

| DRAWN BY: JMA

REVISION NO:

Page 16

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 17

CAP@OM co-op, inc. STREET FIGHTER EX™

REFERENCE INFORMATION

PC BOARD CONNECTIONS AND CONTROLS

Auxiliary Cable ae Connector SS g Test Switch (Not Used)

Harness Connector Speaker Harness Connector

TYPICAL CONTROL PANEL LAYOUT OF STREET FIGHTER EX™

\ SOURCE e@e@ ee@

\v1600200

Page 18

NOTICE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.

The Federal Bureau of Investigation investigates allegations of criminal copyright infringement.

CAIRCOM¥ COIN-OP, INC. 3311 N. Kennicott Avenue Arlington Heights, Illinois 60004 Phone: (847) 797-6192 Fax: (847) 797-6306

Copyright © 1997 CAPCOM ® coin-op, INC., All Rights Reserved