CATHODE RAY TOMES

Moto Frenzy Mini Deluxe TM-379 1st Printing

Moto Frenzy (Atari Games, 1992) · Technical Manual · 84 pages · 53 sections · original scan

Page 1

‘ f

Operator’s Manual

with Schematics

Page 2

e ortice yes guroPe land james set Ww

® thi is nitive: super ititteet

Page 3

Mini-Deluxe

erator’s Manual

with Schematics

A

ATARI

GAMES

Page 4

Intropuction Moto Frenzy MINI-DELUXE

Copyright © 1992 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game. Published by: Atari Games Corporation 675 Sycamore Drive Milpitas, California 95035 Printed inthe U.S.A. 8/92 Produced by the Atari Games Technical Publications Department. Writing & Editing: Amr Eissa and Andrea Dencker Illustration & Design: Mary Ohanessian Sumner NOTICE RE

NON-ATARI

PART

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-Atari parts in the game. © Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.

NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:
  • All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMI ground plane, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

Moro FRENZY MINI-DELUXE 4% INTRODUCTION

SAFETY SUMMARY

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the contro), panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location, The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground, Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atati parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voitage rating, and current rating. In addition, the fuse cover must be in place during game operation.
CAUTION Properly Attach All Connectors. Make sure that the connectors on each prinied circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of foliowing instructions,
WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

it

Page 6

INTRODUCTION “ MoTO FRENZY Mini-DELUXE

CONTENT

1 Set-Up How to Use This Manual Operating the Game Inspecting the Game Control and Switch Locations Power On/Off Switch Volume Control... Self-Test Switch and Bracket Coin Counter .. Installing the Attraction Signs Setting the Coin and Game Options. Game Play... Introduction . Game Play....

2 ~=«~Self-Test Introduction .. Entering and. Exiting the Self-Test Select Test Menu Adjust Volume Control Te: Game Statistics Statistics Screen Histograms 1-6 Coin Options. Game Options. Alpha Test....... Motion Object Test Motion Object ROM Checksums MOB Priority ‘Test. MOB Full Screen Test MOB Picture/Position/Size Test.. Playfield Test Color Test. Convergence Tes' Sound Test ..... Comm (Common) RAM Test. DSP Comm Tests. DSP Link Tests... Video Sync Test... Complete RAM/ROM Test Game RAM Test Game ROM Test .

  • Troubleshooting and Maintenance

Introduction. Maintenance Procedures Introduction .... Cleaning Procedure for Coin Mechanism . Troubleshooting Procedures Repair Procedures Introduction .... Attraction Assemblies Foot Rests. Speakers Start/Fire Button Steering Assemblies... System Logic Assemblies. Throttle Control Video Display .....

4 Parts Illustrations

Part Ordering Information ...... For figure and page numbers, see the list of illustrations that follows.

5 Schematics

See the list of iliustrations that follows.

Statistics Sheet After the end of this manual

Warranty Inside back cover

Page 7

Moto Frenzy MINI-DeLUXE INTRODUCTION

ILLUSTRATIONS

Figure 1-1

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15 Figure 2-16

Figure 4-1

Figure 4-2

Figure 4-3

Figure 4-4

Figure 4-5

Figure 4-6

Figure 4-7 Figure 4-8

Figure 4-9 Figure 4-10 Figure 4-11

Figure 4-12 Figure 4-13 Main Control and Switch Locations... 1-3

Select Test Menu Screen. Adjust Volume Screen Control Test Screen Game Statistics Screen Coin Options Screen .. Game Options Screen... Alphanumeric Test Screen Motion Object ‘Test Screen Playfield Test Screen Color Test Screen... Convergence Test Screen. Sound Test Screen .. RAM Test Screen.. DSP Comm Tests Screen DsP Link Tests Screen Video Syne Test

Cabinet-Mounted Assemblies, Front View Cabinet-Mounted Assemblies, Rear View... oe Steering Control Assembly, Handlebar Detail... ee Steering Control Assembly, Shaker Detail... a Four-Entry Coin Door Assembly, Coin. Mechanism Detail... = Four-Entry Coin Deor Assembly, Coin Door Detail Power Supply Assembly. Moto Frenzy Mini-Deluxe Board Set Assembly .... JAMMA Filter PCB Assembly Power Distribution PCB Assembly JSA ITi PCB Assembly (EPROM Version)... CLARN PCB Assembly Moto Frenzy Mini-Deluxe Game PCB Assembly... Figure 5-1

Figure 5-2

Figure 5-3

Figure 5-4

Figure 5-5

Figure 5-6

Figure 5-7

Table 1-1

Table 2-1 Table 2-2 Table 2-3

Table 3-1 Table 3-2 Table 3-3 Moto Frenzy Mini-Deluxe Game PCB Assembly Schematic Diagram...... 5-3 Power Distribution Assembly Schematic Diagram... wee 27 JSA III PCB Assembly Schematic Diagram..... 5-9 CLARN PCB Assembly Schematic Diagram... JAMMA Filter PCB Assembly Schematic Diagram.............. Moto Frenzy Mini-Deluxe Game Main Wiring Diagram... - 5-21 Coin Door Wiring Diagram . 1-24 see S19

TABLES

Game Specifications ...

Summary of All Self-Test Screens ........ 2-2 Coin Option Settings .. Game Option Settings

General Troubleshooting... ROMs and RAMs Troubleshooting. Voltage Inputs and Test Points. 3-8

Page 8

INTRODUCTION & Moto Frenzy MIN-DeELUxE

NOTES

Page 9

CHAPTER

Set-Up

How to Use This Manual

HIS MANUAL IS written for operators and service personnel. It provides information for setting up, playing, testing, and maintaining your Moto Frenzy” Mini- Deluxe game. Moto Frenzy in the Mini-Deluxe cabinet is a one- or two-player off-road motorcycle racing game with realistic controls and digitized video, The game provides photographically real views of off-road courses in Los Angeles, Maui, Utah, Las Vegas, Kenya, and Norway. ¢ To maximize earnings, you can link two Mini-Deluxe cabinets together so that as many as four players can compete head-to-head. To do so, a separate link kit is available from your authorized Atari distributor for a nominal fee. ¢ Chapter 1 of this manual contains set-up and game play information. @ Chapter 2 contains a description of the self-test procedures. The self-test is important in the Moto Frenzy game. You can troubleshoot the PC boards, main circuits, and controls using the screens in the self-test. You should regularly test the boards and controls with the self-test to keep your game in peak condition and at top earnings. ¢ Chapter 3 contains several troubleshooting tables, plus complete maintenance and repair procedures for the game components. If you have problems with your game, use this chapter to troubleshoot and to repair it. Be sure to perform the preventive maintenance tasks to keep your game in good condition. @ Chapter 4 contains the illustrations and PCB parts lists. ¢ Chapter 5 contains the schematics for all the PCBs and all the wiring diagrams.

Page 10

Cuaprer 1 - Set-Up % Moto Frenzy MiNi-DELuxE,

Operating the Game

To operate your game for maximum income, you should regularly run the self-test and check the controls with the Control Test and Sound Test in the selftest. By using the self-test regularly, you can find and fix problems immediately. This lets you keep your game in top condition.

Inspecting the Game

Characterist Specification

WARNING To avoid electrical shock, do not plug in the cabinet uniil it has been properly inspected and set up for the line voltage in your area.

This cabinet should be connected to a grounded threewire outlet only. If you have only two-wire outlets, we recommend that you hire a licensed electrician to install grounded outlets. Players can receive an electrical shock if the cabinet is not properly grounded. Make note of the power consumption when you set up this game, so that you do not overload your electrical circuit. See Table 1-1 for the power consumption. and the other important specifications of this game. Inspect your Moto Frenzy Mini-Deluxe game carefully to ensure that the game is complete and was delivered to you in good condition. Inspect the cabinet and seat as follows:

  • Examine the exterior of the cabinet for dents, chips, or broken parts.
  • Open the lower rear access panel. Unlock and open the coin door. Inspect the interior of the cabinet as follows:

a. Check that all plug-in connectors on the cabinet harnesses are firmly plugged in. Do not force connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed connector can damage a printed-circuit board (PCB). This will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. ¢. Inspect the power cord for any cuts or dents in the insulation. d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the har-

1-2 Input Current 2.6 Amps at 120 V Line Fuse Rating 3.0 Amps at 250 V, slow blow

Line Voltage 102 to 132 VAC. Temperature 5° to 38° C (37° to 100° F) Humidity Not to exceed 95% relative Width 57 inches (142.5 cm) Length 53 inches (132.5 cm) Height 78.5 inches (196.3 cm) Weight 630 Ibs. (286 kg)

Table 1-1 Game Specifications

ness is plugged in correctly. Check that the green ground wires are connected. e. Inspect other sub-assemblies, such as the video display, controls, printed-circuit boards (PCBs), and speakers. Make sure that they are mounted securely and that the ground wires are connected.

Control and Switch Locations

All of the controls are Jocated on the back of the cabinet or behind the coin doors (see Figure 1-1). The following describes the locations in more detail:

Power On/Off Switch

The power on/off switch is located on the bottom rear panel of the cabinet, below the rear access panel.

Volume Control

There is no volume adjustment knob on this game’s PCB. Instead, volume is adjusted in the self-test. Refer to Chapter 2 of this manual for more information.

Self-Test Switch and Bracket

There are two self-test on/off switches, one for each display. Both switches are mounted on a bracket behind the coin door. Also mounted on each bracket are six auxiliary self-test pushbuttons, three for each display. The top, middle, and bottom buttons are referred to in the self-test as, AUX1, AUX2, and AUX3, respectively.

Page 11

Moto FRENZY MINI-DeLuxE ‘® CHAPTER 1 — SET-UP

Coin Counter (2 places) Self-Test Switch ~ (2 places) Auxiliary Switches 1, 2,3 (6 places)

Figure 1-1 Main Control and Switch Locations

Although there are two additional self-test switches located on the audio PCB of each game, it is recommended that you use the coin door self-test switches.

Coin Counter

The coin counters are located to the right and left of the coin box, inside the coin door.

Installing the Attraction Signs

Each Moto Frenzy Mini-Deluxe game includes two large cardboard attraction signs to promote the game. You can hang both signs back-to-back, from the ceiling, so that the graphics are visible from the back and front of the game. Alternatively, you can hang one sign above the game and the other one in your store window. Insert one end of each string into the hole in the sign, and tie it securely. Insert the two ceiling hooks into the ‘T-bar of the suspended ceiling over the game. To prevent bowing (curving) of the sign, make sure you stretch the strings outward towards the ceiling — beyond the left and right edge of the sign. Do not hang the sign with the strings oriented vertically.

Setting the Coin and Game Options

The Moto Frenzy Deluxe coin and game options are set in the self-test. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Game Play

This section describes the features and play of the Moto Frenzy Mini-Deluxe game.

Introduction

Atari Games’ Moto Frenzy” Mini-Deluxe is a one- or two-player sit-down game featuring high speed, offroad motorcycle racing and shooting action. Each track has challenging obstacles such as rivers to cross, trees, rocks and the cheering crowd to avoid or blast out of the way. The realistic handlebar controls, with a vibrating twist-grip throttle, and the “rump-thump” add to the excitement.

To ensure a long earnings life, there are six different player-selectable tracks, each with unique obstacles: The Los Angeles indoor arena has “big foot” trucks that get in your way; Maui has lava flows and thunder-

1-3

Page 12

Cuaprer 1 - Ser-Up & Moro FRENzy MINI-DELUXE

storms; Utah’s challenging track features huge buffalo and steep cliffs; the desert race in Las Vegas is made more difficult with raging twisters; monkeys try to knock you off your bike in Kenya; and polar bears attack you in the Norwegian race. The race is a timed lap format with extended play for lap completion, bonuses for special stunts, and flashing targets to shoot for turbo speed. Initial race time and bonus times are operator selectable to adjust game difficulty. Competition between players is maximized with Atari’s “rump-thump” feature. When a player is “shot” by another motorcycle rider or “explodes”, a solenoid

1-4 thumper is activated, giving a tactile thump under the fiberglass seat. The twist-grip throttle control also vibrates to give players a realistic motorcycle feel.

To maximize earnings, operators can link two units together for four-playet, head-to-head competition. With four players in the race, if one player is able to finish the lap within the time allowed, all players will be awarded extended time.

Page 13

Self-Test

CHAPTER

Introduction

and controls. You will

see the self-test infor-

mation on the video

display and hear the sound test information

through the speakers. You do not need any

additional equipment to perform the self-test. SE THE MOTO FRENZY™ Mini-

| Deluxe self-test to check the

. condition of the game circuitry

Perform the selftest when you first set up the game,

each time you collect the money, or

when you suspect game problems. This chapter shows the screens in the self-test

and explains each of the tests. The screens

and explanations are arranged in the order they appear in the self-test. Table 2-1 lists

all the self-test screens.

Page 14

(Cuarrer 2 - SELE-Trst @ Moto FRENZY MINI-DELUXE

Entering and Exiting the Self-Test

Both of the games’ self-test switches are conveniently located behind the coin door. (There is one self-test switch for each display). To enter the self-test mode, turn on the self-test switch. Doing so displays the Select Test menu (entitled “Self Test”); see Figure 2-1 Exit the self-test by turning off the self-test switch at any time.

Self Test (Select Test Menu)

Adjust Volume

Control Test

Game Statistics

Coin Options Game Options Alpha(numeric) Test Motion Objects Test Motion Object ROM Checksums MOB Priority Test MOB Full Screen Test MOB Picture/Position/Size Test

Playfield Test Color Test First Color Test (red, green, blue, white) Second Color Test (yellow, cyan, magenta, white) Red Color Purity Green Color Purity Blue Color Purity White Color Purity Grey Color Purity

Convergence Test White Convergence Violet Convergence Blue Convergence Yellow Convergence Sound Test

Common RAM Test

DSP Comm(unication) Tests DSP Link Tests

Video Sync Test Complete RAM/ROM Test

Table 2-1 Summary of All Self-Test Screens

2-2 Almost all the tests are done by pressing one or more of the three auxiliary self-test buttons. These pushbuttons are mounted on a test bracket inside the coin door. The self-test screens refer to AUX1, AUX2, and AUX3, which are the top, middle, and bottom buttons, respectively.

Select Test Menu

Choose which test or screen you want to see from this menu, shown in Figure 2-1. Move up and down the menu by pressing the AUX1 or AUX2 button. Start the selected test by pressing the AUX3 button.

Figure 2-1 Select Test Menu Screen

Adjust the volume of the game using this screen, shown in Figure 2-2. Follow the instructions at the bottom of the screen to change the volume, to restore the old volume level, and to save the new volume and return to the select test menu. (The default volume setting is 11.)

Page 15

Moto Frenzy Mini-DELUXE % Cuaprer 2 — SeLr-Test

ADJUST VOLUME

VOLUME: 3

USE AUX1 & AUX2 TO CHANGE VOLUME ‘TWIST THROTILE TO RESTORE OLD VOLUME PUSH AUX3 TO SET NEW VOLUME AND EXIT

Figure 2-2 Adjust Volume Screen

Control Test

NOTE The coin switches are checked in the Sound test. See the section that follows later in this chapter.

The control test screen is shown in Figure 2-3. This test checks all the pushbutton switches, the steering and throttle potentiometers, the thumper and the shaker. As you use each control, the green bars for the pots lengthen, or the switch names are highlighted in blue. (Remember to check the right and left player controls.) If the changes do not appear on the screen, check the controls and their wiring. Follow this procedure: 1, Simultaneously press the AUX1 and AUX2 buttons to reset the pots for the steering and throttle controls. Then twist the throttle to set the maximum, then release it to set the minimum. Make sure that the green throttle bar corresponds to the changes.

  • Now turn the handlebar control fully left and right to set the left and right limits. Make sure that the green steering bar corresponds to the changes. Check the three numbers displayed in parentheses in the middle of the screen, after the words LIMITS: STEERING. The left number should be Jess than 70, the right number should be greater than AQ, and the middle number should be green. If it is blue, this indicates an error (an out-of-range number).
  • Press the start/fire button on the left handlebar. Make sure that the START/FIRE SWITCH message is highlighted on the screen.

CONTROL TEST

STEERING: mmm C5 3E THROTTLE: 44 00

LIMITS: STEERING = (5E,91,C5) THROTTLE = (43,8F,DC)

START/FIRE SWITCH THUMPER: OFF SHAKER: OFF.

PRESS AUX1 AND AUX2 TO RESET

PRESS AUX3 AND AUX1 TO EXIT

Figure 2-3 Control Test Screen

  • Press the start/fire button on the left handlebar to test the thumper. The thumper will thump once each time the start/fire button is pressed. As the thumper is activated, the THUMPER: OFF message will change to THUMPER: ON.
  • Hold down the start/fire button on the left handlebar and turn the throttle fully to test the shaker. The shaker will shake when the throttle is held in the full position. As the shaker is activated, the SHAKER: OFF message will change to SHAKER: ON. Simultaneously press the AUX1 and AUX3 buttons to return to the select test menu.

Game Statistics

Use the information shown in the statistics and histogram (bar graph) screens to keep track of your game use and maximize your profits. Record the information on the Moto Frenzy Mini-Deluxe statistics page in the back of this manual. The first of the screens is shown in Figure 2-4. (Make several extra copies of this form before writing on it!) The game statistics are collected from the last time the statistics were cleared. Follow the instructions at the bottom of the screen to clear the statistics, to advance to the next statistics or histogram screen, or to go back to the select test menu.

Page 16

Caaprer 2 - SeLr-Test ¢ Moto FRENZY Mini-DELUXE

STA LEFT COINS. RIGHT COINS ‘AUX.COINS NEW GAMES CONTINUATION FREE GAMES IDLE TIME ACTIVE TIME SOLO TIME LINKED TIME ERROR COUNT

TOTAL CREDITS

TOTAL COINS

‘AVG TIME/CREDIT 69 SEC ANG TIME/COIN 69 SEC PRESS BOTH AUX4 AND AUX2 TO CLEAR STATISTIC: ‘AUX FOR HISTOGRAMS

Figure 2-4 Game Statistics Screen

Statistics Screen

The statistics screen lists the following information: ¢ Left Coins shows the number of coins counted in the left coin mechanism.

© Right Coins shows the number of coins counted in the right coin mechanism.

  • Aux Coins shows the number of coins counted on the auxiliary service coin inputs.
  • New Games shows the number of unique games played. A unique game is counted every time a player starts a new game (not a continued game). « Continuation shows the number of games that players continued.
  • Free Games shows the number of games of free play.
  • Idle Time shows the number of minutes that the game was idle.
  • Active Time shows the number of minutes that the game was played.
  • Solo Time shows the number of minutes that the game was played in solo mode (one or two Moto Frenzy Mini-Deluxe cabinets). ¢ Linked Time show the number of minutes that the game was played while linked with another Moto Frenzy Mini-Deluxe cabinet, or two players linked in the same cabinet.
  • Error Count shows the number of errors counted in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEROM at 13C on the Moto Frenzy game PCB.
  • Total Credits shows the number of credits accumu- Jated by the game,
  • Total Coins shows the number of coin accumulated by the game in all coin slots. « Average Time per Credit and per Coin are displayed in seconds. These items are tabulated for all games played since the statistics were cleared. If there are no credits, these lines will not be displayed.

Histograms 1-6

The next screens are six histograms (horizontal bar graphs) showing game times in seconds for the Los Angeles, Maui, Utah, Las Vegas, Kenya, and Norway tracks. All these screens show the number of games played, grouped in 30-second increments. The bottom of each screen shows the total games played on that track and the median game time for that track. The median value means half the games were above that value and half below.

Coin Options

Check and select the coin options on this screen, shown in Figure 2-5. The screen shows the factory default settings in green.

COIN OPTIONS s

Free Play

No.

Discount to continue: Yes

Game cost 2coins 1 credit

Bonus for quantity buy-in: None

ch value:

Vv more ¥

ESS AUX1 TO SELECT SETTING

PRESS AUX2 TO SELECT OPTION

PRESS AUX3 TO SAVE SETTINGS AND EXIT TWIST THROTTLE TO RESET FACTORY OPTIONS

Figure 2-5 Coin Options Screen

To move through the options, to change or save the settings, or to return to the select test menu, follow the instructions shown at the bottom of the screen. The coin option settings, with defaults, are shown and explained in Table 2-2.

Page 17

Moro Frenzy MINI-Detuxe Cuaprer 2 — SeLF-Test

Option Available Settings Explanation

Free PlayNovYesLets you choose free play to demonstrate the game.

Discount to Continue Now Yes If set to Yes, this option reduces by 56% the player's cost to continue a game (always rounded up to the next full coin)

Game Cost1 coin 1 creditThe number of coins required for one credit.

2 coins 1 credit vw

8 coins 1 credit Bonus for Quantity None v Lets you choose from various kinds of bonuses or no bonus. Buy-in 2 coins give 1 3 coins give 1 3 coins give 2 4 coins give 1 9 coins give 2 Q coins give 3

Right Mech Value1 coin counts as 1 coinThe number of coins each coin counts as in the right coin

1 coin counts as 2 coins mechanism.

1 coin counts as 7 coins 1 coin counts as 8 coins

Left Mech Value—{ coin counts as 1 coinwThe number of coins each coin counts as in the left coin

1 coin counts as 2 coins mechanism.

1 coin counts as 7 coins 1 coin counts as 8 coins

v Manufacturer's recommended settings

Table 2-2 Coin Option Settings

Game r@) tions ‘To move through the opiions, to change or save the

P' settings, or to return to the select test menu, follow the

instructions shown at the bottom of the screen. The Check and select the game options on this screen, game options, with defaults, are shown and explained shown in Figure 2-6. The screen shows the factory de- in Table 2-3. fault settings in green,

Gane oPnoNs|Alpha Test

(DEFAULTS IN.GREEN) otReDUM The alphanumeric test, shown in Figure 2-7, checks the BIKE COLOR: condition of the alphanumerics in the game. If you see ee an error in the alphanumerics or graphics on the

esNATTRACT|screen, check the EPROM at 13N on the Moto Frenzy

STEERING SHAKER MOTOR: game PCB. To page (Scroll) the screen up and down, ” 4 or to return to the select test menu, follow the instruceo tions shown at the bottom of the screen. CLEAR HIGH SCORE TABLE: NO AUTO HIGH SCORE RESET ENABLE

PRESS AUX? TO SELECT SETTING PRESS AUX2 TO SELECT OPTION PRESS AUX3 TO SAVE SETTINGS AND EXIT TWIST THROTTLE TO RESET FACTORY OPTIONS,

Figure 2-6 Game Options Screen

Page 18

Cuaprer 2 — Seir-Test Moro FRENzy MINI-DELUXE

Option Available Se’ gs Explanation

Difficulty LevelEasiestEasierEasyMediumw Sets the game difficulty. The left and right sides must be set

Med, Hard Hard Harder Hardest to the same difficulty level.

Bike ColorRed-Right/Blue-Left ¥Red/Blue are the default colors of the players’ motorcycles

on the screen. If you link two games together, set this option to Green/Orange on the second linked game. Also, regardless of whether you link two games, make sure that the left and right sides in the same cabinet are set to the same Bike Color setting. Green-Right/Orange-Left

Music in Attract (Mode) Yes ”NoLets you turn the sound on or off in the attract mode.
Clear High Score Table YesNowClears the high score table the next time you select the

game mode.

Auto High Score ResetEnable ¥Disable

Automatically clears the high score table periodically. v Manufacturer's recommended settings Table 2-3 Game Option Settings

Figure 2-7 Alphanumeric Test Screen

Motion Object Test

Motion Object ROM Checksums

The first motion object test screen, shown in Figure 2-8, examines the checksums of the motion object ROMs. If the checksums match, TEST PASSED is displayed. If the checksums do not match, either you have a defective EPROM/ROM or a chip may be installed incorrectly.

MOB Priority Test

The second motion object test screen shows eight vertical bars that are cut off by horizontal bars, forming a stairstep from top left to bottom right. Only the green bar on the far right should extend the full vertical height of the screen. Any other display would indicate a priority failure,

MOB Full Screen Test

The third motion object test screen shows two squares; one grows to full-screen size, while the other shrinks. Use the throttle to control the rate of growth of these squares, Make sure the growth is smooth; any tearing of lines or pixels and/or inconsistent colors indicate a problem with the motion object circuitry.

MOB Picture/Position/Size Test This test is intended to be used only by Atari Games technicians to troubleshoot a faulty board.

MOTION OBJECT ROM CHECKSUM ERROR

4 MEG ROM CHECKSUM PAIR AT IS SHOULD BE SIL, 31N 6AF5. 6BE8

OBEO 0AC1 BE7C 8EB4

AUX3 = NEXT TEST

Figure 2-8 Motion Object Test Screen

Page 19

Moro Frenzy Mint-DeLuxe # CwAPTER 2 — Seir-Test

Playfield Test

The playfield test screen, shown in Figure 2-9, tests the movement of the playfield. To scroll the playfield continuously in a horizontal direction, move the handlebar to the right or left. To scroll the picture vertically, also hold down the start/fire button. Make sure that the playfield screen is clean and scrolls smoothly across the screen.

Figure 2-9 Playfield Test Screen

Color Test

This test has seven screens, the first of which is shown in Figure 2-10. Advance to each screen by pressing the AUX! button.

  • The first color test indicates the dynamic range of the video display color circuit. The screen should show four bands (red, green, blue, and white, from top to bottom), ranging from bright to dark, left to right. The red, green, and blue bands are produced by only one color gun being turned on in each band. At the bottom is a white band, in which all three color guns are turned on.
  • The second color test shows the same as the first color test, but with two color guns being turned on in three bands — a yellow band (red and green guns), cyan band (blue and green guns), and magenta or purple band (blue and red guns). At the bottom is a white band.
  • The remaining five screens are color purity tests. The rectangles of color shown are red, green, blue, white, and grey. Each screen should display a straight rectangle of color, with no curving at the corners, no unevenness of color, and no lines in the display. Figure 2-10 Color Test Screen

If any of these screens are not correct, adjust the video display as described in the video display manual. Return to the select test menu by pressing AUX3.

Convergence Test

The convergence test has four screens — white, violet, blue, and yellow backgrounds with white grid lines. The white screen is shown in Figure 2-11. To see the remaining screens, press the AUX1 button. Press the AUX3 button to go to the select test menu.

Figure 2-11 Convergence Test Screen

Check the following on the screens:

  • The grid lines should be straight within 3.0 mm and the lines should not pincushion or barrel.
  • The convergence of the lines on the violet and black screens should be within 2.0 mm. If these screens do not meet these criteria, adjust the video display as described in the video display manuai.
Page 20

Chaprer 2 — Seir-Test Moto Frenzy MINi-DELUXE

Sound Test

The sound test indicates the condition of the sound ef fects circuit on the game PCB. The sound test screen appears in Figure 2-12.

NOTE The Audio PCB must be installed and connected in the game to perform this test.

SOUND TEST

451011
1819 2021
2829 30«31
3839 4041

4 YTS

NUMBER OF SOUNDS”: 41 SOUND CPU STATUS : GOOD USE STEER TO SELECT SOUND AUX1=PLAY AUX2=STOP

COIN MECH SWITCHES: LEFT

Figure 2-12 Sound Test Screen

To select a sound, to play a sound, or to return to the select test menu, follow the instructions shown at the bottom of the screen. (You can have numerous sounds. playing simultaneously, or you can have silence, depending on which ones you select.) Verify that the Sound CPU status is good. Also press the left and right coin mechanism switches: the 0 on the screen should change to a 7 while you press the corresponding switch.

Comm (Common) RAM Test

Use this selection screen, shown in Figure 2-13, to see if the common RAM is OK. This test is automatically run when you switch to game mode.

When the test runs successfully, you see the message COMMON RAM OK! If the RAM is bad, the message COMMON RAM ERROR is displayed and you must replace the Common RAM board.

2-8 Press the START button to exit.

COMMON RAM TEST

COMMON RAM Ok!

Figure 2-13 RAM Test Screen

DSP Comm Tests

The tests under this main screen item check the local communications of the game (see Figure 2-14). Press the AUX1 or AUX2 buttons to select one of the tests, and press AUX3 to do the selected test. The 2105 special functions are intended to be used only by Atari Games technicians to troubleshoot a faulty link board.

DSPCOMM BOARD 2105 TESTS

Bar VITAL SIGNS 2105 INTERNAL DATA RAM 2105 INTERNAL PROGRAM RAM 2105 LINK 2105 SPECIAL FUNCTIONS

Figure 2-14 DSP Comm Tests Screen

After you do each of the tests, you should see OK displayed on the screen. In the Vital Signs test, however, you should see the messages It’s Alive and Interface

Page 21

Moro Frenzy MINI-DeLuxe % Cnaprer 2 - Seir-Test

OK. if any test fails, contact the Atari Games Customer Service office closest to you for help.

DSP Link Tests

The tests under this main screen item check the link between two Moto Frenzy Mini-Deluxe games (see Figure 2-15). All of these tests (except for the cable test) are intended to be used only by Atari Games technicians.

DSPLINK TESTS

exe INITIALIZE 2101, RX ON GET RECEIVE STATUS FLAG CLEAR THE RECEIVE BUFFER FULL RECEIVE BUFFER WITH TEST DATA DUMP RECEIVE BUFFER DUMP RECEIVE BUFFER WHEN FULL. GET TRANSMIT STATUS FILL TRMT BUFFER WITH TEST OATA AND SEND FILL TRANSMIT BUFFER WITH 5555 AND SEND DUMP TRANSMIT BUFFER SEND TRANSMIT BUFFER SEND TRANSMIT BUFFER — SCOPE LOOP

CABLE TEST

Figure 2-15 DSP Link Tests Screen

To use the cable test, set one game to “Echo” and the other game to one of the “Originate” settings. The screen will show hexadecimal numbers transmitted by the originating game and what data it received back. Then reverse the settings of the games: change the game that was echoing to be the one originating, and vice versa.

NOTE A link problem can remain hidden and unsolved if you do not check the link in both directions.

If incorrect data is received in any of these cable tests, the failure will appear in a color other than green. You may have a problem with the cable, plug, harnesses, or connectors.

Video Sync Test

This test is useful only if you have linked two Moto Frenzy Mini-Deluxe games together. The video syne test (see Figure 2-16) checks that both games are synchronized. Make sure that both linked games are displaying this test; then check the positions of the red/blue and green/orange blocks on the screens, They should not drift from the correct positions, which are shown in Figure 2-16. If the blocks on one screen are not in the same position as on the other screen or the blocks are drifting, you could have two causes for this problem, The CLARN PCB could be bad, or the link harness or related connectors on it could be defective.

VIDEO SYNC TEST

AUX3 = EXIT

Figure 2-16 Video Sync Test

Complete RAM/ROM

Test

When you turn on the power, the game automatically runs through the random-access memory (RAM) and read-only memory (ROM) test. This test is noi part of the self-test procedure. Regardless of whether or not the game has a problem, it will always advance to the attract mode. The game will stop only if you power it up and the self-test switch has been previously turned on.

Game RAM Test

No message appears while the test is checking the RAMs. if more than 30 seconds elapse and the self-test

Page 22

Cuaprer 2 - Seuy-Test Moto FRENZY Mint-DELUXE

menu doesn’t appear, the game has a problem. The two RAMs in this game are located at 13E and 13E/F on the Moto Frenzy game PCB; either of them could be bad.

if the test finds no RAM errors, no message appears and the program goes to the ROM test after 15-20 seconds.

Game ROM Test

If the test finds no ROM errors, no message appears and the program goes to the title screen in the attract mode. If a ROM fails, a message may be displayed. However, the program may be unable to show the location of the failed ROM — you may only see six zeroes where there should be a chip location. The ROM error test takes a few seconds. If you think you have a ROM error, but the screen shows no messages, check the ROMs at 23E, 23), 37E, and 37J on the Moto Frenzy game PCB. Check these locations for bent pins or incorrectly inserted chips. Also see Table 3-2 for information about the locations of the ROMs and their functions.

Depending on how bad the ROM error is, you may not be able to enter the selftest.

Page 23

CHAPTER 3

Troubleshooting and Maintenance

Introduction

Mini-Deluxe game. The

maintenance section gives

information on cleaning the

parts. The troubleshooting

section contains several

tables to help determine the » HIS CHAPTER contains mainte-

nance, troubleshooting and repair

procedures for your Moto Frenzy™ source of a problem and the steps necessary

to repair it. The repair section contains the

steps necessary to remove and install the ser-

viceable parts. Together,

these three sections provide

a complete guide to servic-

ing your Moto Frenzy” Mini-

Deluxe game.

Page 24

Citaprir 3 — TROUBLESHOOTING AND MAINTENANCE @ Moro Frenzy MINI-DELUXE

Maintenance Procedures

Troubleshooting Procedures

Introduction

This section describes the maintenance procedures for all of the major assemblies and components of the game. The maintenance procedures should be performed every 3-4 months on a regular basis.

WARNING Before performing any maintenance, please observe aii of the foilowing safety precautions:
  • Turn the game's power off.
  • Unplug the power cord from the electrical socket.
  • Secure loose clothing such as ties and long sleeves that could get caught within the game. 4, Remove all meta! jewelry such as waiches and necklaces that could conduct electricity from the game's power sources.

Cleaning Procedure for Coin

Mechanisms

Regular use of the coin mechanisms may result in a buildup of residue and dirt. If this is the case, clean the coin mechanism by following the steps below (refer to Figure 4-5 and Figure 4-6 for detailed part information on the coin door). 1, Open the upper coin door,

  • Open the gate on the door that covers the magnet. Use the blade of a screwdriver to scrape away any metal filings that have collected on the magnet.
  • Clean the loose dust and dirt from the coin mechanism with a lint-free rag or a soft brush.
  • Clean the dirt and residue from the coin path with a toothbrush. Hot, soapy water may be used to help dissolve dirt and residue.
  • Blow out ail the loose dirt and dry the coin mechanism. with compressed air.
  • Close the gate on the door that covers the magnet and close the upper coin door.
CAUTION Never lubricate the coin mechanism with oi! or grease.

This section is designed to help determine the source of a malfunction and detailed information on repairing the problem. Table 3-1 General Troubleshooting, is divided into two columns. The left-hand column is broken down into the general nature of problems. The right-hand column lists suggested solutions to solve the problem. Table 3-2 ROMs and RAMs Troubleshooting, is designed. to help determine the specific ROMs and RAMs that are the source of a game logic malfunction. The left-hand column shows some problems that may result from malfunctioning ROMs and RAMs. The middle column shows the ROMs and RAMs that may be the source of the problem and their purposes. The right-hand columin shows the PCB locations of the ROMs and RAMs that may be causing the problem. Table 3-3 Voltage Inputs and Test Points, is divided into three columns. The left-hand column shows the correct voltages that should be measured. The middle column shows the physical locations of the test points or LEDs. ‘The right-hand column shows the sources and purposes of the voltages.

Repair Procedures

Introduction

This section describes the repair procedures for all of the major assemblies and componenis of the game. Before performing any repairs, use the tables in the Troubleshooting Procedures section to help narrow the source of the problem. The Maintenance Procedures section may also provide a good starting point for fixing many game problems before beginning what might be unnecessary repairs.

Page 25

MOTO FRENZY MINI-Detuxe * CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE

WARNING Before performing any repairs, please observe all of the following safety precautions:
  • Turn the game's power off.
  • Unplug the power cord from the electrical socket.
  • Remove loose clothing such as ties that couid get caught within the game. 4, Remove all metal jewelry such as watches and necklaces that could conduct electricity from the game's power sources.

Attraction Assemblies

Attraction Light The 15 watt, 18" fluorescent attraction light lights the attraction panel. Replace the light by following the removal and installation steps below.

  • Unfasten the 13 square drive screws that secure the light housing assembly (refer to Figure 4-1 and Figure 4-2.)
  • Unfasten 2 retaining clips that secure the light to the light fixture and remove the light.
  • Install the new fluorescent light by following the previous steps in the reverse order.

Attraction Light Fixture ‘The attraction light is responsible for providing power to the fluorescent light and holding it in place. Failure of the light fixture may result in poor or no light. If this is the case, replace the light fixture by following the removal and installation steps below. 1, Unfasten the 13 square drive screws that secure the light housing assembly,

  • Disconnect the wiring harness from the light fixture to the power supply.
  • Unfasten 2 retaining clips that secure the light to the light fixture and remove the light. 4, Remove the 2 screws that secure the light fixture to the cabinet and remove the light fixture.
  • Install the new light fixture by following the previous. steps in the reverse order.

Foot Rests

Each fooi rest consisis of a metal peg covered by a rubber sleeve. The foot rests are responsible for providing support and traction for the rider during game play. Replace damaged foot rests by following the removal and installation steps below.

  • Cut the damaged rubber sleeves from the metal pegs.
  • Slide the new rubber sleeves over the metal pegs.

Speakers

Each game has four speakers, two for each player. The speakers provide the music and sounds for the game and self-tests, Failure of the speakers may result in distorted or no sound. If this is the case, replace the speakers by following the removal and installation steps below.

  • Unlock the rear access panels of the cabinet and remove ther.
  • Disconnect the wires from the speakers using the rear access panels,
  • Unfasten the 4 square drive screws that secure each speaker grille to the front panel of the cabinet.
  • Unfasten the 4 screws that mount each speaker in the recess of the front panel of the cabinet.
  • Install the new speakers by following the previous steps in the reverse order.

Start/Fire Button

‘The start/fire button is used for starting game play and for firing the bike’s gun during game play. Failure of the start/fire button will result in no response from either of its functions. If this is the case, follow the removal and. installation steps (refer to Figure 4-3.)

  • Unfasten the 3 screws that secure the left-hand grip to the handlebars and remove the hand grip.
  • If the solder connections are broken or otherwise bad, resolder the start wires.
  • To ieplace the start switch: a. Cut the start wires as close to the switch leads as possible. (Be sure to label the wires before disconnecting them.) b. Unfasten the screw that secures the start switch to its housing. c. Secure the new switch to the housing with the screw,

d. Resolder the start wires to the new switch. e. Check the start switch in the Control Test of the self-test to make sure the new switch is working. 4, Re-install the hand grip with the 3 screws.

Page 26

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE % MOTO FRENZY MiNI-DELUXE

Steering Assemblies

This section describes the removal and installation procedures for the various assemblies and components that provide the steering motion and control. Steering Potentlometer The steering potentiometer (SK ohms) is responsible for measuring the turning motion of the handlebars and relaying the information to the PCBs for game play. Failure of the steering potentiometer will result in no response from the game’s graphics to the steering control. In this case, replace the steering potentiometer by following the removal and installation steps below.

  • Disconnect the wires from the steering potentiometer leads.
NOTE Before disconnecting the wires from the steering potentiometer leads, labe/ the wires as to the position of the potentiometer leads. That way you can correctly reconnect the wires when installing the new potentiometer.
  • Unfasten nut and washer that secure the steering potentiometer to the steering bracket.
  • Install the new steering potentiometer by following the previous steps in the reverse order.

System Logic Assemblies

This section describes the repair and maintenance procedures for the major assemblies and components that are related to the system's logic and electronics, including the printed-circuit boards (PCBs) and the power supply. These components are housed in the bottom rear cabinet below the video display. Moto Frenzy Game PCB Set The Moto Frenzy game PCB set is responsible for the display graphics and game play. Failure of the game PCB set may result in erratic or no game play. If this is the case, repair or replace the game PCB set by following the removal and installation steps below.

  • Unlock the rear access panel of the cabinet and remove it.
  • Disconnect the hamess connectors from the game PCB set.
  • Unfasten the screw and spacer that secures the game PCB set to the cabinet. Remove the game PCB set and attached cover (refer to Figure 4-8.)
CAUTION Before handling static-sensitive components, properly ground yourself to discharge buildup of static charges.

4, Re-install the game PCB set by following the previous steps in the reverse order.

Electronic Game Link Each Moto Frenzy Mini-Deluxe game is linked internally. Electronic game link connector are available to electronically link two Moto Frenzy Mini-Deluxe game units together for four-person play. Damage to the electronic game link connector may cause the four-person play to function incorrectly or not at all. If this is the case, replace the electronic game link connector by following the removal and installation steps below,

  • Unlock the rear access panel of the cabinet and remove it.
  • Disconnect the external game link cabie from the game link connector.
  • Remove the ground plane hat and disconnect the link connector from the CLARN PCB.
  • Unfasten the 4 screws that secure the game link plate to the cabinet and remove the game link connector and attached plate.
  • Install the new game link connector by following the previous steps in the reverse order. Power Supply The power supply is responsible for providing power to all of the game assemblies that require it. Failure of the power supply may result in erratic game play or no power at all. If this is the case, repair or replace the power supply assembly by following the steps below. 1, Unlock the rear access panel of the cabinet and remove it.
  • Disconnect the wiring harnesses from the power supply.
WARNING The power supply can contain high voltages even after the power is turned off. To avoid injury, observe all of the safety precautions before working on the power supply. (Refer to the introduction in the Maintenance Procedures section.)
Page 27

Moto Frenzy MINI-DELUXE ¢ CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE

  • Unfasten the 4 screws that secure the power supply assembly to the cabinet, and remove the power supply assembly. 4, Re-install the power supply assembly by following the previous steps in the reverse order.

ROMs/RAMs The ROMs and RAMs contain the programming routines used by the game PCB set to control game play. Refer to Table 3-2 ROMs and RAMs Troubleshooting, in the Troubleshooting Procedures section to determine the ROMs or RAMs that are malfunctioning. Replace the damaged. ROMs or RAMs by following the removal and installation steps below.

  • Remove the game PCB set according to the procedure in the Moto Frenzy Game PCB Set section.
CAUTION Before handling static-sensitive components, properly ground yourself to discharge buildup of static charges.
  • Remove the damaged ROMs and RAMs from the game PCB set using a chip extraction tool.
  • Install the new ROMs and RAMs by plugging them in the game PCB set sockets.

4, Re-install the game PCB set by following the steps in the Moto Frenzy Game PCB Set section in the reverse order.

Throttle Control

Throttle Potentiometer

The throttle potentiometer (5K ohms) is responsible for measuring the twisting motion of the throttle control and relaying the information to the drive motor to accelerate and decelerate the rolling pin. Failure of the throttle potentiometer will result in no response from the drive motor to the throttle control. If this is the case, replace the throttle potentiometer by following the removal and installation steps below.

  • Unfasten the 3 screws from the base of the throttle that secure it to the handlebars and remove the throttle control (refer to Figure 4-3.)
  • Loosen the retaining screw that secures the potentiometer to the throttle shaft until the potentiometer and the attached bracket slide easily from the throttle shaft.
  • Unfasten the nut and washer that secure the bracket to the potentiometer and remove the bracket from the potentiometer.
  • Disconnect the wires from the throttle potentiometer, labeling the leads first, so you can correctly reconnect them later.
  • Install the new potentiometer by following the previous steps in the reverse order.
NOTE The metal tab extending from the bracket should point away from the leads on the potentiometer when properly installed.

Throttle Torsion Spring The throttle torsion spring is responsible for returning the throttle control to its center position. If the spring has stretched excessively or is broken, the throttle control will stay in the position the rider turns it to. This may result in decreased responsiveness in the rider’s acceleration and deceleration control. If this is the case, replace the throttle torsion spring by following the removal and installation steps below.

  • Unfasten the 3 screws from the base of the throttle that secure it to the handlebars and remove the throttle control,
  • Unfasten the retaining screw that secures the potentiometer to the throttle shaft and remove the potentiometer and attached bracket from the throttle shaft.
  • Unfasten the retaining screw that secures the torsion spring to the throttle shaft. 4, Remove the plastic retaining washer and the torsion spring from the throttle shaft.
  • Install the new torsion spring on the throttle shaft: a. Secure the straight end of the spring through the hole in angle bracket. b. Holding the looped end of the torsion spring back with a slotted screwdriver or a pair of pliers, tighten the retaining screw to the throttle shaft. c. Hook the looped end of the torsion spring over the retaining screw.
NOTE Make sure that there is sufficient clearance between the end of the torsion spring retaining screw and the right angle bracket so that there is no interference with the throttle’s operation. The cap of the retaining screw should be between the 2 throttle stops and should strike the stops in their centers when properly adjusted.

3-5

Page 28

‘CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE @ MOTO Frenzy MINI-DELUXE

Problem Suggested Acti

Coin Mechanism Problem

Check the wiring connections to the coin mechanism. Check the voltage to the + side of the mechanism. Test the coin mechanism with the Sound Test screen in the self-test. an

Throttle Control Problem

Check the harnesses and connections to the throttle control

  • Check the throttle potentiometer. Throttle control is not responding

Throttle control does not return to closed 1. Check the throttle return spring.

Steering Control

Handlebars do not return to center 1. Check the lower tension spring.

Game play does not respond to steering 1. Check the harnesses and connections to the steering controls,

  • Check the steering potentiometer..

Start Switch Problem

Check the start switch in the Contro! Test of the self-test . Check the wire connections and solder joints to the start switch. Check the start switch for continuity using an ohmmeter. Replace the start switch only if it is bad. BOs

Sound Problem

Check the speaker volume setting, Check the voltage on the PCB edge connector. Check the connections from the PCB to the speakers. Check the voltage level to the PCB. Check the sound ROMs in the Sound Test of the self-test procedure. Check the resistance of the speakers for 8 Ohms. Repiace the speaker(s) only if bad, NOapoens

Video Display Problem

Check to see that the game is plugged in Check to see that the game is turned on Check the line fuse. Check the display brightness. Check the solder connections on the line filter and the transformer. Check the edge connector to the PCB. Check the harnesses and connectors to the video display PCB. Check the voltage levels to the video display PCB . Run through the following checklist. If you answer no to any question, you have a problem with the video display, not with the game circuitry. In this case, refer io your video display service manual. a. Do you have power to the video display? b. Are the video display’s filaments lit? c. Do you have the correct voltage to the video display? Screen is dark CPNOTABNH

Attempt to run a complete RAM/ROM test in the self-test. Replace the RAM. Only a colored screen appears o>

Display area wavers or is too small Check the voltage ievels to the video display PCB. Check the B+ to the video display. (Refer to the video display manual.) No

Table 3-1 General Troubleshooting

3-6

Page 29

Moro Frenzy MINI-DELuxE ¢ CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE

Picture is wavy

Picture is upside down or reversed

Convergence, purity or color problems

Picture is not centered

Electronic Game Link Problem

  • Check the connection of the monitor ground wire to the monitor.
  • Check the connections of the sync inputs.
  • Switch the horizontal or vertical yoke wire connections to the video display.
  • Use the self-test mode to digitally adjust the video display.
  • Use the adjustment procedures in your video display manual.
  • Use the centering procedures in your video display manual.

Seat Thumper Problem

  • Check the harnesses and connections between both games.
  • Only qualified technicians having experience with high-power devices should troubleshoot this system. The solenoids and the solenoid/motor PCB run on live voltage and can cause serious injury.

Table 3-1 General Troubleshooting, Continued

‘ob!

ROMs ROMs/RAMs Source and Purpose

The program works, but the motion objects are incorrect or non-existent.

Garbage appears on the screen or game play doesn’t work correctly.

The text or numbers are incorrect or non-existent.

The sound is incorrect or non-existent.

The moving backgrounds graphics are Motion Object ROMs (responsible for moving graphic 31L, 31N, 31R, 31T, objects) 33L, 33N, 33R, 33T, 35L, 35N, 35R, 35T, 371, 37N, 37R, 37T

Program ROMs (responsible for game control) 23E, 23J, 37E, 37J

Alphanumeric ROM (responsible for controlling graphic text and numbers) 13N

Audio ROMs (responsible for controlling sound) Audio Program ROM 120 Audio ADPCM ROM 19E

Playfield ROMs (responsible for controlling background incorrect or non-existent. graphics) 2D, 2U, 5D, 5u, 8D, 8d RAMs

The display color is red. Working RAM

The display color is green. Playfield RAM

The display cclor is blue. Motion Object RAM

Table 3-2. ROMs and RAMs Troubleshooting

Page 30

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE @ Moto FRENZY MINI-DELUXE

Voltage Test Point or LED Location

+5 + 0.25 VDC +5V1

CR3 LED (game PCB)

CR9 LED (JSA Audio lil PCB)

CR3 LED (JSA Audio Ill PCB)

+12V +VOP {pin 4 of LM324)

-5V -VOP (pin 11 of LM324) Voltage Source and Purpose

Logic power from the switching power supply.

Lights when 5 V is applied to the PCB and the reset (RST) jumper is open.

Lights when the +12 V supply is good.

Lights when the —5 V supply is good

+12 V from the switching power supply. Positive supply for the analog circuitry.

~5 V from the switching power supply (if connected). Negative supply for the analog circuitry. Table 3-3 Voltage Inputs and Test Points

  • Slide the plastic retaining washer on top of the torsion spring.
  • Re-install the potentiometer and attached bracket to the throttle by tightening the potentiometer retaining screw against the flat edge of the potentiometer shaft.
NOTE The plastic retaining washer should be below the potentiometer retaining screw when properly installed.
  • Re-install the throttle control to the handlebars by securing it with the 3 screws at the base of the throttle control.

Video Display

To repair, replace or make adjustments to the video display, follow the removal and installation steps below.

WARNING High Voltage The video display contains lethal high voltages. To avoid injury, do not service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation This video aisplay is designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube (CRT) may implode if ‘struck or dropped. The shattered glass from the tube may cause injury up to six feet away. Use care when handling the display and when removing it from the game cabinet. Also, wear gloves to protect your hands from the sheet-metal edges.
  • Unfasten the 8 square drive screws that secure the monitor doors to the cabinet and remove them.
  • Discharge the high-voltage from the cathode-ray tube (CRT).
NOTE The label on the video display assembly shows a circuit for discharging the high-voltage contained in the CRT to ground when the power is off.
Page 31

Moro Frenzy Mini-Detuxe CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE

a. Secure one end of a solid 18-gauge wire to a wellinsulated or wooden handle screwdriver.

b. Secure the other end of the wire to an earth ground. c. Briefly touch the blade end of the screwdriver to the CRT anode by sliding it under the anode cap. d. Wait 2 minutes and repeat the previous step. . Disconnect all of the wire harnesses from the video display. . Unfasten the 13 square drive screws that secure the light housing assembly and remove it. . Unfasten the 10 square drive screws that secure the lower glass retainers. Remove the display shields and card-board bezels. . Unfasten the 4 flat washers and nuts that secure each video display chassis to the cabinet monitor mounting brackets.

  • Remove the video display assembly from the cabinet.
NOTE Do not attempt to remove the video display without its chassis.
  • Install the new video display

. If necessary, adjust the new video disby following the previous steps (excluding steps 2a.—2d.) in the reverse order.

play’s brightness, size, centering, purity and convergence according to the video display service manual.

3-9

Page 32

CHapTER 3 ~ TROUBLESHOOTING AND MaINTENANCE % Moro FRENZY MINI-DELUXE

Page 33

CHAPTER 4

~ Parts Illustrations

Part Ordering Information

@, HIS CHAPTER provides informa- — number of this manual, and the serial tion you need to order parts for — number of your game. With this informa

tion you need to order parts for — number of your game. With this informayour game. The printed-circuit tion, we can fill your order rapidly and board (PCB) parts lists are arranged in al- —_ correctly. We hope this will create less phabetical order by component. Within each sec-

tion the parts are arranged numerically by part number. When you order parts, give the part number, part name, the downtime and more

profit from your games. Atari Games Customer Service phone numbers are listed on the inside front cover of this

manual.

Page 34

Cuaprer 4 — Parts ILLustRations Moto Frenzy MiNI-De1uxe

050317-01 Moritor Shield (2places)

050806-01 Loft Instructions Decal, Blue

050308-01 Center Glass Retainer| 178348-0108 112! W. Foam Tane 171101-001

“Tapping Seow (4 places) ‘A051007-01, Test Panel Assy. 176015-112 Ho xais" Par-Hd. Tapping Screw (2 places) 044440-01 Cashbox Bracket 176015-172| #10 x 3/4" Panta. ‘Tapping Serew (2places) 051085-01, ‘Seam Covering Decal (2 places)

(2 places) sce, +#1/4-20 Nylon Locknut |

#A/4200 141 wrateo-one M2 ban) 76°Giip Hence “ is {2 places) 2 places) 172020-1224 (2 places) |

175014-1050) 1/4 Flat Washer places) 089461. ump-Thump Assy. 051072-01 Loft Bezet 051078-02 Right Bezel With Graphics +176056-002 4/2" W. Foam Tape: (4 places) ‘A051046-01 ‘Attract Panel Assy. 77026-0044 #9/4:20 Nav Washer Assy. (éplaces) 75-55248 914-201 112" Carriage Bott (4 places) 176019-212 #8 x 3/4" Sq. Or. Screw (7 places) A051045-01 Light Housing Assy. 178263-0801 112! Vinyi Foam Tape 176019-212 8-9/4" Sq, Dr. Screw (13 places)

1750150125 21/4 Ext-Lock Waster (B places) 725516 #1/4.20 1" HexcHd, Screw (B places)

(050806-02 Fight Instructions, Decal, Red

1950309-02 Aight Lower Glass Retainer 050309-01, Loft Lower Glass Retainer 178263-0801 102" x 1/46" Vinyl Foam Tape 176019-212 #8 x 9/4" Sq. Dr. Screw (10 places) ‘A050870-01 ‘Control Steering Assy- 176263-0801 112° 1/16" Vinyl Foam Tape 1175002-007 Flat Washor places) 17026-0044 1#1/4-20 NuvWasher Assy. (8 places) 75-55248 14-20 «1 112" Carriage Bolt (® places) '059803-01 Loft Control Red Decal 050803-02 Fight Contra! Red Decal 050862-01 Loft Seat Decal (050652-02 Fight Seat Decal

(050146-01 ‘Upper Seat Wood 176019-212 #8 x 3/4" Sq.Dr. Screw (12 places)

951000-01 / | 051062.0 Collar Skit

‘A051052-01 Upper & Lower Seat Assy. (2 places) 1051036-01 & 02 Formed Seat

(2 places) 1176097-4106 #1032 Hex Tampor- Proof Screw (Bplaces) 1175014-3040 Flat Washer (8 places)

050985-01 Speaker Gril (4 places) tower Sette aig Deca |_| SBE 2 places) 1175002-007 Flet Washer #8 x 3/8" Sa, Dr. Sew

Figure 4-i Cabinet-Mounted Assemblies, Front View A050330-01 B 148007-108 4-12" Dia. Speake (pieces) 176015-110 0x 56" Pen-Ha Tapping Screw (16 places) ‘A080340-01 ‘Spetker Harness Assy. (4 paces)

Page 35

Moto FRENZY Mini-DELUXE “ CHAPTER 4 — Parts ILLUSTRATIONS

039450-01 050320-01 FCC Compliance Label one boot 3086) (038066-01 04245201 ; FBI Warning Label Sock Waring Late 170003-001 176019-220 18" Fluorescent Light #81 1/4" Sq, Dr. Screw 171086-001 , (eplaces) 418" Fluorescent Lamp Fixture 176015119, #10 x 51" Pan-Hd. Tapping Sorow (2 places) 178232-001 139022-401 Lamp Retainer Clip 25" Std.-Res. @ places) Hey Color splay (2 pleces) 038150-01 75014-1050 Product LD. Lebel 41/4 Flat Washer (-10) places) 098158-01 77026-0044 Product LD. Label : 414-20 Nu (-03) : Washer Assy. onn01-01 a 02 : (6 places) Left & Fight Side Decal eB s ceaieet eecen Prod. Lae ‘8051008-01 : : Power Supply Assy. ‘A050824-01 176015-112 Power Distribution #10x3/4" Pant, e PCB Assy. ‘Tapping Sorew 178256-001 ‘a places) L:Syje Nylon 1700-138 be : Standott 8-32 Hex-Nut (4 places) { 72-6088 6x 1/2" Pan- Hems Not Shown: Ha. Screw i ps 150081-001 “a9 Power Supply Cord A051084-01 178340-001 Moto Frenzy Ceiling Mobile Board Set Assy. Hook with Sting 038156-01 (4 places) Product .D. Label 050638-01 (-03) Attraction Sign 76015-112 (2 places) #10 x 3/4" Pan-Hd. 051088-01 Tapping Screw Header Folder 175008-002 TH390 | Nylon Washer 25' Welis Gardner 079-01 Display Service Manual Fis ™.379 19e Label Operator's Manual 8050948-01 ‘A051040-01 ON/OFF Wood Vendor Sitch Assy. KitList Assy. 176003-108, '4050338-01 #444112 Pan- Main Hamess Assy. Hd. Screw A050339-01 (2 places) Power Hamoss Assy. A050342-01 050315-01 Solenoid Harness ASS, Sel-Test Label Cabinet Door 050803-03 178018-001 (2 places) Left Control Blue Decal 41/2" Crown Staple 1998086-01 050809-04 (6 places) Shock Warning Right Control eo 05032701 178093-001 s/02" Tamper Proof Wood Cabinet Leg Lovler Pate Fan Guard Hex Key Driver +178023-001 Rubier Caster (6 places)

Figure 4-2 Cabinet-Mounted Assembiies, Rear View 4050330-01 B

Page 36

A050870-01 A Figure 4-3 Steering Control Assembly, Handlebar Detail Cuaprer 4 — Parts Ittusrrations “& Moro Frenzy Mini-Detuxe

Page 37

Moto Frenzy Mint-Detuxe Cnaprer 4 — Parts ILLUSTRATIONS

177010-254 12-20 Polymer Hex-Nut 107013-001 SAN Olt 051062-01 Colar Skint (Called out in Cabin 108014-001 Final Assy. Drawing)| Hand-Grip Cement 175014-1077 Flat Washer

Frame Woldment

(050873-01 Return to Center Guide

'A050343-01 ‘Control Harness Assy. 179012-010 1° Clip-Ring

72-8808 892 x 1/2" Soc-Hd. Cap Screw

1119008-1001 5K Potentiometer

70026-0209 Extension Spring ‘7eai1-004e 750. Sink Tubing 178) beige Hort Washer 12V Shaker Motor Ass (050877-01 (2places) 72-8010 Porsracket | 178017-2019 10:82 x" SoHo. Cap Seow HHO Lock Washer (@places) | 2places)

Figure 4-4 Steering Control Assembly, Shaker Detail ‘8050870-01 A

4-5

Page 38

Cuarrer 4 — Parts IiusTRATIONS & MoTo Frenzy Mini-DeLuxe

99-15025 Left Coin Inlet

99-15113 Key Hook|

99-15056| ‘Screw for Bezel

99-15096 ‘Sw. Adjuster

99-15056| Screw

99-15131 Elastic Locknuut 99-15132 Snap-on Sleeve

99-15130 Snap-on Clip

99-15133 Hold-Down Bracket

99-15027 |Coin Ret. Plate

99-15128 | NutWasher for M/S Mounting Screw

99-15129 Mounting Stud (2 places) |

99-15051 Lamp Holder

99-15029 Bracket

99-15042: 99-15086 Coin Mechanism

“™ L- —— 99-15104 Base Plate WiPivot & Stud

99-15100 —tamp _

99-15026

99-15056 ‘Screw for Bezel

99-15028 Coin Return Box

'99-15056 ‘Screw for Bezel

99-15134 '4-40-1" Pan-Head Screw

99-15126 M/S Flat-Head Mounting Screw

99-15085 ‘Switch: ‘Coin Door Harness

Figure 4-5 Four-Entry Coin Door Assembly, Coin Mechanism Detail

4-6 171101-001

Page 39

Moto FRENzY MINI-DELUXE # CHAPTER 4— PaRTs ILLUSTRATIONS

99-15038; 99-15036 99-15089 Lock Assy Bezel for Button Cover

© _ 99-1501 thru 99-15012 Retum Button 99-15039 Bezel for Cover & “—— g9-t5125 -~ Frame Hinge Screw b

99-15088 Clamp

99-15135 Frame Clamp Screw

Die-Cast Frame

NOTE: The Coin Box Assembly was intentionally left out and is shown in the Cabinet-Mounted Assemblies drawing (Figure 4-1 of this manual).

Figure 4-6 Four-Entry Coin Door Assembly, Coin Door Detail 171101-001

Page 40

Carter 4 — Parts Iu.ustrations “ Moto FRENZY Mini-DELU:

4-8

Page 41

Moro FRENZY Mini-DELUXE ¢ Cuarter 4 — Parts ILLustRATIONS

72-HA4606S 6-32 x 318" X-Rec Screw (2 places) 179231-002 2 Position Flat-45-90 051003-01 ‘Terminal Block Power Supply Chassis

| § =} ® fo 5 fe 2 a]

CH

® ® Hl

® ® ef ®

{142058-001A049468-03050888-01

'solation Dual SOL/MTR PCB Assy. Power Supply Bracket

Transformer178265-001149015-001

peuinaence Nylon L-Style PCB Standoff 200W, AT Power Supply

ge xs(4 places)72-HA4606S
“Rec Screw72-HA4606S#6-32 x 4B" X-Rec Screw

(4 places) +#6-32 x 3/8" X-Rec Screw (5 places) (4 places)

Figure 4-7 Power Supply Assembly A051004-01 A

Page 42

CuarTer 4 — PARTS ILLUSTRATIONS # Moto FRENZY MINI-DeLUXE

4-10 178349-3644 8-32 x 2.3/4" MF ‘Alum. Standoff (2 places) 178181-6616 1/4" Round, 1” Lg. Alum, Standoff (2 places) 175015-0113 #6 St/Cad Ext- Tooth Lock Washer (2 places) 172025-3620 632 x 1 3/8" Lg, X-Rec Pan-Hd, Screw (2 places)

178065-100 4" Wire & Cable Tie 178068-002 1" Sq, Cable Tie Mount

A050941-01 CLARN Interconnect Hamas Assy.

051059-01 Double Board Set Hat

177018-206

{10 places) A049810-01 Moto Frenzy Game PCB Assy. {EPROM Version} (2 places)

JAMMA Filter PCB Assy. 4047292-02 | (2 places) |

A050349-01 CLARN Ribbon Assy.

‘4050274-01 CLARN PCB Assy.

178278-616 +#6-82 x 1.00" Nylon Standoff 177000-536 +#6-32 Nylon Hex Nut

178047-012 6" Nylon Card Guide (2 places)

# 6-32 Brass Thumbnut [—— 178349-3644 6-32 x 2.9/4" MF Alum. Standoft (4 places) 175015-0113 #6 Stl/Cad, Ext-Tooth Lock Washer (4 places) 172025-3606 6-32 x 3/8" Lg, X-Rec Pan-Hd, Screw (4 places)

051060-01 Double Board Set Base

178171-1612 6-32 x .75%, 1/4" Round Alum. Standoff (2 places) 172025-3606 6-32 x 3/8" X-Rec, Pan-Hd. Screw (4 places) 175014-2021 #6 Flat Washer (4 places) 17517-3013 +#6 Spiit-Lock Washer (4 places}

034536-13 3x 3x 9/4" Thk, Foam Vibration Damper (hidden) A048974-12 JSA III PCB Assy. (EPROM Version) (2 places) 178278-612 #6-32 x .75" Nylon Standoff (2 places) 177000-536 +#6-32 Nylon Hex Nut (2 places)

Figure 4-8 Moto Frenzy Mini-Deluxe Board Set Assembly A051044.01 B

Page 43

Moro FRENZY MiNI-DeLuxe @ CHaprer 4 — PARTS ILLUSTRATIONS

Figure 4-9 JAMMA Filter PCB Assembly A047292-01 A

JAMMA Filter PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
C1-5, C7,2200 pF, SOV, 3-Pin EMI Filter Cap.140006-222C32, C33270 pF, SOV, 3-Pin EMI Filter Cap.140006-271
C9, C10270 pF, 50V, 3-Pin EMI Filter Cap.140006-271C36, C372200 pF, 50V, 3-Pin EMI Filter Cap.140006-222
C11-15, C18-21, C24-27, C30aConnector, 56 Ckt., .156 Ctr, RT179240-056

2200 pF, 50V, 3-Pin EMI Filter Cap. 140006-222

4-11

Page 44

CHAPTER 4 — Parts ILLUSTRATIONS % Moro Freszy Mixi-Deexe

Cw © cis

WARNING:

8288

JM2 cL cz FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, MREZ2_—-MREZZ lem + REPLACE ONLY WITH A FUSE AIA OF THE SAME TYPE AND ua ELECTRICAL RATING. Q = F2 4A/25oy CRI cR2 FB2 F3 4A/250V Faas 3

Fa 4a/2sou rer FH 4A/2s0V Fu 3

REMOVE PLASTIC POLARIZING KEY AS SHOWN BEFORE LOADING.

Figure 4-10 Power Distribution PCB Assembly A050824-01 B

Power Distribution PCB Assembly Parts List

Desig- Desig-

nator_ DescriptionPart No.nator—_ DescriptionPart No.
C1-6,C9-C16 .01 pF, SOV, +80% -20% Cer. Cap. — 122002-10311, L2N12N Ferrite Bead Inductor141003-005
c7-8100 pF, 100V, +5% Cer. Cap.122016-101RI, R2, R4,
yi, 72Hdr. Connector, 12 Ckt., .156 Ctr, Key 9 179213-012RGResistor, 1.2 K Q, +5%, 1/8 W110027-122
JM1Har, Connector, 4 Ckt., .100 Ctr, Key 2.179118-004R3, RS.Resistor, 470 Q, +5%, 1/8 W110027-471
JA, JBHdr. Connector, 4 Ckt., .200 Ctr179310-004GND1Test Point179051-001
J8.J9Hdr. Connector, 6 Ckt,, .156 Ctr179309-006Ql, Q2.—-TIP120 Transistor133051-001
JM2Har. Connector, 9 Ckt., .156 Ctr, Key 3 179213-009HS1, HS2TO-220 Heat Sink with #4-40 Stud —_ 178063-007
JcHdr. Connector, 9 Ckt., .156 Ctr, Key 6179213-009F1-F4BAG 4 Amp 250 V Slow-Blow Fuse146008-4022
CR1, CR2MR822 Diode131019-001(HS1, HS2) #4-40 Steel/Zinc Hex Nut177000-132
CR3~CR8_~MYV5053 Light-Emitting Diode131027-002(HS1, HS2) #4 Steel/Zinc Internal-Tooth Washer75-054
FB1-FB43AG Fuse Block179225-4401(HS1, HS2) #4 Steel/Zinc Rect. Washer178347-001

4-12

Page 45

Moro Frenzy Mini-DeLuxe ¢ CnapTer 4— Parts ILLUSTRATIONS

© RI o

orUW&°(pha 03

43 LM3403 in 23 2 Ls273 YO)" [+a g

Qo 2208R C2= 8 peeLMa4ORBRD

(oneeni 1 () c2% 9 ‘e. . HS4 aw 2B uz [E ers a! Se)

eta

omy 5weQS
a 5ea]LS138

o Ny x fl i" es pi LS74 20 Qua = as, 7

wal!mo#2ooe 1

Figure 4-11 JSA III PCB Assembly (EPROM Version) A048974-12 A

4-13

Page 46

Cuapter 4 — Parts Inustrations % Moto Frenzy MINI-DELUXE

JSA Ill PCB Assembly (EPROM Version) Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
Sockets16AIntegrated Circuit, 7418374137144-001
8DSocket, 16 Pin, .300179259-01617BIntegrated Circuit, 74F74137436-001
9C1Socket, 24 Pin, .600179257-024
11CSocket, 40 Pin, .600179257-040V7GAL16V8, 25 ns136085-1038
12€Socket, 28 Pin, .600179257-028WEEPROM, 200 ns, 128K x 8136089-1049
18BIntegrated Circuit, 741874137023-001
12ESocket, 32 Pin, .600179257-03218CIntegrated Circuit, 74L$138137177-001
15CSocket, 28 Pin, .600179257-028
15ESocket, 32 Pin, 600179257-03219BIntegrated Circuit, 7418393137146-001
WCSocket, 20 Pin, .300179259-02019CIntegrated Circuit, 741874137023-001
19EEPROM, 100 ns, 512K x 8136094-0081
17E, 19ESocket, 32 Pin, .600179257-03220BIntegrated Circuit, 74LS393137146-001
20CSocket, 20 Pin, .300179259-02020CGALI16V8, 25 ns136085-2046

Miscellaneous Hardware Capacitors

++1005V1 Test Point179051-001C1,C2Capacitor, 47 UF, 50V, Electrolytic123015-476
AGND1Test Point179051-001C3Capacitor, .1 UF, 50 V, +80%-20%,
GND1,GND2 Test Point179051-001Ceramic122002-104
_—Nut/Washer Assy.177026-0036C4Capacitor, 10 uF, 25 V, Electrolytic — 124009-106
HS1Heat Sink, TDA2030178190-032C5-C7Capacitor, .1 LF, 50 V, +80%-20%,

Ceramic 122002-104

JAUDConnector, 36 Ckt, .1 Bottom Entry179299-036
swSwitch, Slide, SPDT160040-001C8Capacitor, 10 UF, 25 V, Electrolytic124009-106
—Nut/Washer, Zinc177026-0036C9, C10Capacitor, .1 UF, 50 V, +80%-20%,
—Screw, Pan-Head, #6-32x3/8,Ceramic122002-104
Cross-Recessed, Cadmium72-1606SC13Capacitor, 47 UF, SOV, Electrolytic123015-476
_—Thermal Compound107031-001C14-C22Capacitor, .1 UF, 50 V, +80%-20%,

Ceramic 122002-104 Integrated Circuits

1DIntegrated Circuit, Quad Op-Amp,23Capacitor, 10 UF, 25 V, Electrolytic—124009-106
1M3403137673-001C24, C25Capacitor, .22 UF, 50 V, +10%, Ceramic 122015-224
2AIntegrated Circuit, TDA2030137301-001€26-C28Capacitor, .1 MF, 50 V, +80%-20%,
3DIntegrated Circuit, 4066B137580-001Ceramic122002-104
4AIntegrated Circuit, TDA2030137301-001C29Capacitor, 1000 pF, 50 V, +10%, Ceramic 122015-102
4C,5CIntegrated Circuit, 4066B137580-001€30-C32Capacitor, .1 MF, 50 V, +80%-20%,
6D, 6FIntegrated Circuit, Quad Op-Amp,Ceramic122002-104
1M3403137673-00133Capacitor, 3300 pF, 50 V, +5%, NPO,
7cIntegrated Circuit, 741S273137040-001+80%-20%122019-332
8AIntegrated Circuit, 7418174137122-001C34, C35Capacitor, .1 WF, 50 V, +80%-20%,

Ceramic 122002-104

8DIntegrated Circuit, YM3012137402-001C37Capacitor, 2200 pF, 50 V, +80%-10%,
9C1Integrated Circuit, YM2151137401-001Ceramic122015-222
10AIntegrated Circuit, 74LS273137040-001
1cIntegrated Circuit, 6502 A137577-001C38Capacitor, .1 LF, 50 V, +80%-20%,

Ceramic 122002-104

12CEPROM, 200 ns, 64K x 8136094-008039Capacitor, .015 HF, 100 V, +5%, Poly 126009-153
12EEPROM, 200 ns, 128K x 8136089-1051C40Capacitor, 10 UF, 25 V, Electrolytic — 124009-106
1BAIntegrated Circuit, 74LS240137251-001CélCapacitor, 1000 pF, 50 V, +10%, Ceramic 122015-102
14AIntegrated Circuit, 7418374137144-001

C42, C43 Capacitor, 6800 pF, 50 V, 80%-10%,

15CIntegrated Circuit, RAM, 8K x 8, 100 ns, 6 137535-004Ceramic122015-682
15EEPROM, 200 ns, 128K x 8136089-1050
Page 47

Moto Frenzy Mini-Detoxe @ CHarrer 4 ~ Parts ILLUSTRATIONS

JSA IH PCB Assembly (EPROM Version), Continued Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No,
C44, C45Capacitor, .1 UF, 50 V, +80%-20%,R35Resistor, 20 K Q, 5%, 1/8 W110027-203
Ceramic122002-104R36Resistor, 39 K Q, +5%, 1/8 W110027-393
C46, C47Capacitor, 1006 pF, 50 V, +10%, Ceramic 122015-102R37Resistor, 160 K Q, +5%, 1/8 W110027-164
C48, C49Capacitor, 3300 pF, 50 V, 5%, NPO 122019-332R38Resistor, 10 K Q, +5%, 1/8 W110027-103
C50Capacitor, 10 HF, 25 V, Electrolytic124009-106R40Resistor, 30 K Q, 5%, 1/8 W110027-303
C51-C54Capacitor, .1 WF, 30 V, +80%-20%,R41Resistor, 15 K Q, £5%, 1/8 W110027-153
Ceramic122002-104R42Resistor, 150 K Q, £5%, 1/8 W110027-154
R43.Resistor, 7.5 K Q, +5%, 1/8 W110027-752

Diodes

CRI, CR2Diode, 1N4001131048-001R44Resistor, 15 K Q, +5%, 1/8 W110027-153
CR3Diode, MV5053, Light-Emitting131027-002R48.Resistor, 3.3 K Q, £5%, 1/8 W110027-332
CR6-CR8_Diode, 1N4001131048-001R49Resistor, 33 K Q, +5%, 1/8 W110027-333
CRODiode, MV5053, Light-Emitting131027-002R50Resistor, 30 K Q, +5%, 1/8 W110027-303
ResistorsR51Resistor, 6.2 K Q, £5%, 1/8 W110027-622
R1,R2 _ Resistor, 10 K Q, 45%, 1/8 W110027-103R52, R53Resistor, 12 K Q, +5%, 1/8 W110027-123
R3Resistor, 33 K Q, £5%, 1/8 W110027-333R54Resistor, 7.5 K Q, 5%, 1/8 W110027-752
R4Resistor, 1 Q, +5%, 1/8 W110027-010R55.Resistor, 560 Q, +5%, 1/8 W110027-561
RSResistor, 33 K Q, +5%, 1/8 W110027-333
R56Resistor, 470 Q, +5%, 1/8 W110027-471
ROResistor, 470 Q, +5%, 1/8 W110027-471RSTResistor, 100 Q, +5%, 1/8 W’110027-101
R7Resistor, 33 K Q, +5%, 1/8 W110027-333R59Resistor, 10 Q, £5%, 1/8 W110027-100
RBResistor, 1 K Q, +5%, 1/8 W110027-102RO2Resistor, 15 K Q, +5%, 1/8 W110027-153
ROResistor, 33 K Q, +5%, 1/8 W110027-333
ROSResistor, 10 K Q, +5%, 1/8 W110027-103
R10Resistor, 470 Q, +5%, 1/8 W110027-471R64Resistor, 15 K Q, +5%, 1/8 W110027-153
R11Resistor, 1 K Q, +5%, 1/8 W110027-102ROS.Resistor, 7.5 K Q, 5%, 1/8 W110027-752
R12Resistor, 470 Q, +5%, 1/8 W110027-471ROOResistor, 10 K Q, 45%, 1/8 W110027-103
R13Resistor, 1 K Q, £5%, 1/8 W110027-102
ROTResistor, 3.3 K Q, $5%, 1/8 W110027-332
R14Resistor, 470 Q, £5%, 1/8 W110027-471R68Resistor, 6.8 K Q, +5%, 1/8 W110027-682
RISResistor, 1 K Q, +5%, 1/8 W110027-102ROOResistor, 16 K Q, +5%, 1/8 W110027-163
R16Resistor, 470 Q, +5%, 1/8 W110027-471R70Resistor, 2 K Q, +5%, 1/8 W110027-202
R17, R20___Resistor, 1 K Q, +5%, 1/8 W110027-102
R71Resistor, 6.8 K Q, 45%, 1/8 W110027-682
R22Resistor, 470 Q, +5%, 1/8 W110027-471R72Resistor, 10 K Q, +5%, 1/8 W110027-103
R23Resistor, 33 K Q, +5%, 1/8 W110027-333R73Resistor, 20 K Q, +5%, 1/8 W110027-203
R24Resistor, 1 K Q, +5%, 1/8 W110027-102
R25Resistor, 1 Q, +5%, 1/8 W110027-010
R26Resistor, 1.2 K Q, +5%, 1/8 W110027-122
R28BResistor, 10 Q, +5%, 1/8 W110027-100
R29Resistor, 5.1 K Q, +5%, 1/8 W110027-512
R30Resistor, 15 K Q, +5%, 1/8 W110027-153
R31Resistor, 10 K Q, +5%, 1/8 W110027-103
R32Resistor, 620 K Q, +5%, 1/8 W110027-624
R33Resistor, 330 K Q, +5%, 1/8 W110027-334
R34Resistor, 82 K Q, +5%, 1/8 W110027-823

4-15

Page 48

Cuaprer 4 — Parts ILLUSTRATIONS Moro Frenzy Mini-DELUXE

NOTES

4-16

Page 49

4-17 A050274-01 A Figure 4-12 CLARN PCB Assembly ,

MV5053 7 100/16v-+-— ) O84 cx CE

‘| ao) a Rt cy uC] sq hae “otf ose

c7a >

[a] mvsos3 | 8) cs

4100/1603. © cw : ‘cH Catt Ossie FT >) —vs0s3

Fi36 oo ' ce 8 nye Yew 10¢qq 1197 in

5s ) a

IK Moto FRENzy MiNI-Detuxe “% CHAPTER 4 — PARTS ILLUSTRATIONS

Page 50

CuapTer 4— Parts ILLUSTRATIONS ¢ MOTO FRENZY MINI-DELUXE

CLARN PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
ySocket, 28 Pin, .600179257-028c1Capacitor, 100 UF, 16 V, Electrolytic,
2FSocket, 28 Pin, .300179259-028Radial123013-107
3Socket, 68 Pin, PLCC179237-068C2Capacitor, 47 pF, 100 V, 5%, Ceramic 122016-470

3 Capacitor, 33 pF, 100 V, 5%, Ceramic 122016-330

8DSocket, 68 Pin, PLCC179237-068C4, C5Capacitor, 100 pF, 100 V, 5%, Ceramic 122016-101
8FSocket, 28 Pin, .300179259-028
3Socket, 20 Pin, .300179259-020C6-C8Capacitor, 33 pF, 100 V, 45%, Ceramic 122016-330

C9-C17 Capacitor, 100 pF, 100 V, +5%, Ceramic 122016-101

11DSocket, 24 Pin, .600179257-024C18Capacitor, .1 UF, 50 V, +80% -20%,

Ceramic 122002-104

+IC, 7418374137144-001C19Capacitor, 33 pF, 100 V, +5%, Ceramic 122016-330
++1005VL_ Test Point179051-001€20Capacitor, .1 UF, 50 V, +80% -20%,
++1005VR Test Point179051-001Ceramic122002-104

€21-C26 Capacitor, 100 pF, 100 V, 45%, Ceramic 122016-101

1cIC, 74F32137486-001C27Capacitor, 100 UF, 16 V, Electroiytic,
yEPROM, 64K x 8, 200 ns136094-0071Radial123013-107
1KIC, 74F0O137327-001C28-C35Capacitor, .01 UF, 50 V, +80% —20%,
3IC, ADSP2105, 40 MHz137674-040Ceramic122002-103
4cIC, 74F0O137327-00136-C41Capacitor, .1 LF, 50 V, +80% -20%,
4D, 4FIC, 7418245137134-001Ceramic122002-104
4KIC, 74F74137436-001C42Capacitor, 33 pF, 100 V, +5%, Ceramic 122016-330
5CIC, 74F00137327-001C43-C57_Capacitor, 100 pF, 100 V, +5%, Ceramic 122016-101

C58-C69 Capacitor, 1000 pF, 100 V, +10%,

5J, 5KIC, 7418374137144-001Ceramic122015-102
6AIC, 74F32137486-001
6D, 6F‘IC, 7418245137134-001C70-C88, Capacitor, .1 WF, 50 V, +80% 20%,
oyIC, 7418374137144-001Ceramic122002-104
C89, C90Capacitor, 22 pF, 100 V, +5%, NPO122016-220
7IC, 7418244137038-001C91-C97_—Capacitor, .1 UF, 50 V, +80% —20%,
7KIC, 7418374137144-001Ceramic122002-104
8/9KIC, 74F 138137521-001C98, C99Capacitor, 100 pF, 100 V, 45%, Ceramic 122016-101
8D1010 FPGA136094-0072C100, C101 Capacitor, 1000 pF, 100 V, +10%,

Ceramic 122015-102

8FIC, RAM, 8K x 8, 45 ns, 3137667-045
8}GALI16V8, 25 ns13604-0070CRI-CR3._Diode, MV5053, Light Emitting131027-002
8KIC, 74F74137436-001
9/10KIC, 74F138137521-001GND1-4Test Point179051-001
xIC, 74F74137436-001aConnector, 60 Circuit, Rec, 1x .1C179303-060
10FIC, 7418393137146-001j2Connector, 60 Circuit, Header,
10IC, 75ALS194137675-0014 Wall, .1 x .1C179021-060
10KIC, 74F04137437-001J3Connector, 2 Circuit, Header, .100 Ctr 179048-002

yy Connector, 11 Circuit, Header,

11FIC, 7418259137137-001-100 Ctr, Key 5179118-011
11KIC, 75ALS195137676-001
12DIC, 7418273137040-001
12FIC, 7418259137137-001
Page 51

Moto Frenzy Mini-DeLuxe “ CHAPTER 4 — PARTS ILLUSTRATIONS

CLARN PCB Assembly, Continued Parts List

Desig- Desig-

nator —_ DescriptionPart No.nator _ DescriptionPart No.
J8Connector, 26 Circuit, Header,R17Resistor, 1 KQ, +5%, 1/8 W110027-102
2x 13, Pol179261-026R18-R37 R39 Resistor, 100 Q, +5%, 1/8 W110027-101
JoConnector, 11 Circuit, Header,R40, R41Resistor, 1 KQ, £5%, 1/8 W110027-102
100 Ctr, Key 3179118-011R42Resistor, 100 Q, +5%, 1/8 W110027-101

jlo Connector, 11 Circuit, Header,

-100 Cur, Key 2179118-011R43-R45Resistor, 10 KQ, 5%, 1/8 W110027-103
R46Resistor, 150 Q, +5%, 1/8 W110027-151
R1, R2Resistor, 220 Q, +5%, 1/8 W110027-221R47Resistor, 100 2, +5%, 1/8 W110927-101
R3Resistor, 10 Q, +5%, 1/8 W110027-100
R4Resistor, 10 KQ, +5%, 1/8 W110027-103XtCrystal, 14.318M, Osc. Module,
RSResistor, 100 Q, +5%, 1/8 W110027-1013x 3 DIP144009-001
RO-R13,Resistor, 10 KQ, +5%, 1/8 W110027-103xiCrystal, 14.318M, Osc. Module,
R14Resistor, 470 Q, +5%, 1/8 W110027-4713x 3 DIP144009-001
RISResistor, 1 KQ, £5%, 1/8 W110027-102X2Crystal, 10.000 MHz144000-013
R16Resistor, 470 Q, 45%, 1/8 W110027-471

4-19

Page 52

Carter 4 — Parts ILLUSTRATIONS ¢ Moto Frenzy MINI-DELUXE

° iid = =z . ar ° 0 0 a= an 3 8 all} fo D o- dh = 8 i

  • |p 0 o- jo = | f

0 a = x= #

= TS) GIIEo fo C= 30 By) at Cao oe A : 2 Ca ce = esa o \ =H (p 2 ifs C30 Ces =e Tey [ = @ ° 20 tem =O = OC = Hl = ta 0 3a - 50s Ca a0 = a - R4) | a: |) sowvass i: al | ar) Fete Thora —_ = 0 C0 &, ao 4 A o } Oa ss 3BB = A ste

Figure 4-13 Moto Frenzy Mini-Deluxe Game PCB Assembly (EPROM Version) A049810-04 A.

4-20

Page 53

Moto FRENZY MINI-DELUXE & CHAPTER 4 ~ PARTS ILLUSTRATIONS:

Moto Frenzy Game PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No,
2D, 2pSocket, 32 Pin, .600179257-0322DEPROM, 512K x 8, 100 ns136094-0030
3LSocket, 40 Pin, .600179257-0403LIC, SOS137550001
3NSocket, 24 Pin, .300179259-024
5D, 5)Socket, 32 Pin, .600179257-0323NGAL20V8, 25 ns136094-0019
3RIC, 7415163 A137114-001
5N, 5RSocket, 20 Pin, .300179259-0203SIC, 741874137023-001
5U, 5V, SW Socket, Zip 28179302-0284BIC, 7418260137332-001
6LSocket, 40 Pin, .600179257-040
7N, 7RSocket, 20 Pin, .300179259-0205ARes, R/2R, 1K/2K118016-001
5DEPROM, 512K x 8, 100 ns136094-0031
8D, 3)Socket, 32 Pin, .600179257-0325NGAL16V8, 25 ns136094-0010
10U, 10V, 10W5RGAL16V8, 25 ns136094-G011

Socket, Zip 28 179302-028

12Socket, 20 Pin, .300179259-02058IC, 74F08137483-001
13CSocket, 24 Pin, .600179257-024STIC, 74F32137486-001

5U, SV, 5W IC, VRAM, 256K x 4, 100 ns 137682-100

138, 13F — Socket, 24 Pin, .300179259-0246LIC, PFHS137419-104
13NSocket, 32 Pin, .600179257-032
14RSocket, 20 Pin, .300179259-0207ARes, R/2R, 1K/2K118016-001
165Socket, 68 Pin, Plec179237-0687IC, 7418260137332-001
7NGAL\6V8, 25 ns36094-0009
17LSocket, 20 Pin, .300179259-0207RGALI16V8, 25 ns136094-0012
207Socket, 24 Pin, .300179259-024
208Socket, 20 Pin, .300179259-0207SIC, 741886137079-001
2A, 21, 21), 21M, 21N8DEPROM, 512K x 8, 100 ns136094-0032
Socket, 28 Pin, .600179257-0288LIC, 74F02137481-001
8MIC, 7418157137029-001

218, 22R, 228

Socket, 20 Pin, .300179259-0208NIC, 74F85137685-001
238, 23). ~— Socket, 32 Pin, .6004792570328R, 85IC, 74F157137494-001
23R, 238, 25D, 25K, 27D9cIC, 7418153137104-001
Socket, 20 Pin, .300179259-020OF, 9KIC, 74LS298137201-001
2Socket, 68 Pin, PLCC179237-068
OLIC, 74LS163 A137114-001
30NSocket, 20 Pin, 300179259-0209MIC, 74F04137437-001
31L, 31N, 31R, 31T, 33L, 33N, 33R, 337ONIC, 7418244137038-001
Socket, 32 Pin, .600179257-032OR, 9SIC, 74F157137494-001
34E, 35)Socket, 28 Pin, .600179257-028
35L, 35N, 35R, 357, 37E, 37J, 37L, 37N, 37R, 37T10D, 10FIC, 74HCT273137655-001
Socket, 32 Pin, .600179257-03210KIC, 74F04137437-001
10LIC, 7418273137040-001
+IC, 74F163137345-00110MIC, 74LS378137305-001
+EPROM, 128K x 8, 100 ns136094-002110NIC, 7418244137038-001
+EPROM, 512K x 8, 100 ns136094-005310R, 10SIC, 74F157137494-001

10U, 10V, 1oW IC, VRAM,

1NIC, 7415163 A137114-001256K x 4, 100 ns137682-100
IRIC, 74F00137327-00111KIC, 74F153137492-001
1SIC, 74F04137437-001
1UIC, 74F32137486-001MLIC, 7418273137040-001
11MIC, 7418377137145-001
2ARes, R/2R, 1K/2K118016-00111NIC, 741.5378137305-001
2BIC, 7406137052-001VIR, 11SIC, 74F157137494-001
Page 54

CHAPTER 4 — Parts ILLUSTRATIONS “ Moto FRENzy MINI-DELUXE

Moto Frenzy Game PCB Assembly, Continued Parts List

Desig- Desig-

natorDescriptionPart No.nator__DescriptionPart No.
12KIC, 74F153137492-00119M, 19NIC, 7418245137134-001
12LGAL16V8, 25 ns136094-000719R, 198IC, 74F374137420-001
12MIC, 7418157137029-001
22RIC, 74°37137622-00119WIC, 748378137612-001
20FIC, 74F138137521-001
128IC, 74F174137531-001207GALG001, 35 ns136094-0005
12VIC, 7418377137145-00120LIC, 74F153137492-001
13CIC, 28C16-200, 200 as137648-200
1BE, 13FIC, RAM, 2K x 8, 35 ns, 3137534-00120RIC, 74F374137420-001
208PROM, 825147136094-0003
13NEPROM, 128K x 8, 100 ns136094-002520wIC, 74F163137345-001
14KIC, 74F153137492-0012AIC, ADC0809137243-001
14LIC, 7418163 A137114-001
14MIC, 7418378137308-00221E, 21}IC, RAM, 32K x 8, 70 ns, 6137615-070
21LIC, 74F153137492-001
ARGALIOV8, 10 ns13604-000621M, 21NIC, RAM, 32K x 8, 70 ns, 6137615-070
14sIC, 74F163137345-00121PIC, 74F04137437-001
MvIC, 74F377137622-001
15KIC, 74F153137492-0012RIC, 74F374137420-001
218PROM, 8251471360940002
15LIC, 74F20137530-00121wIC, 74F163137345-001
15MIC, 7418377137145-00122A, 22BIC, 7418257137136-001
15NIC, 747260137570-001
15RIC, 74F169137496-00122LIC, 747153137492-001
22RGALI6V8, 25 ns136094-0014
swIC, 74832137486-001228PROM, 828147136094-0001
16D, 16FIC, 74F374137420-001zwIC, 74F163137345-001
16K.IC, 748157137494-001
16LIC, 7418163 A137114-0012BIC, 7418244137038-001
238,EPROM, 128K x 8, 100 ns136094-0221
16M, 16NIC, 7418374137144-00123)EPROM, 128K x 8, 100 ns136094-0222
16RIC, 74F169137496-00123LIC, 74Fi53137492-001
168FPLA, 20 ns136094-0004
16WIC, 74F163137345-00123RGALI6V8, 25 ns1360940016
238GALI6V8, 25 ns136094-0015
17D, 17FIC, 7418244137038-00123WIC, 74F157137494-001
17KIC, 7418197137240-00124BIC, 7418273137040-001
17LGALI6V8, 25 ns136094-0008
17M, 17NIC, 7418374137124-00124LIC, 74F153137492-001
24M, 24NIC, 74F163137345-001
17RIC, 74F169137496-00124RIC, 74F151137490-001
17WIG, 74F163137345-00125DGALI6V8, 25 ns136094-0013
18D, 18FIC, 7418245137134-001
18KIC, 74F08137483-00125FIC, 74732137486-001
25KGALI6V8, 25 ns136094-0018
i8LIC, 74F153137492-00126BIC, 7418245137134-001
18M, 18NIC, 7418245137134-00226LIC, 74F153137492-001
18RIC, 748378137612-001
18wIC, 74F260137570-00126M, 26NIC, 74F163137345-001
26RIC, 74F157137494-001
19D, 19FIC, 74F138137521-001270GALI6V8, 25 ns136094-0017
19KIC, 741874137023-00127FIC, 748244137502-001

4-22

Page 55

Moro Frenzy MINI-DeLuxe @& CHAPTER 4 — PARTS ILLUSTRATIONS

Moto Frenzy Game PCB Assembly, Continued Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
aTIC, CPU, PLCC137658-101C4, C5, C7, CB Capacitor, .01 UF, 59 V, +80% -20%,
27WIC, 74F377137622-001Ceramic122002-103
28BIC, 7418245137134-001©), C10Capacitor, 1000 pF, 100 V, +10%, Ceramic
28LIC, 74F00137327-001122015-102
28M, 28NIC, 74F163137345-001C11, C12Capacitor, 270 PFC, 50 V, EMI Filter140006-271
28RIC, 74F86137649-001C13,Capacitor, 100 pF, 100 V, +5%, Ceramic122016-101
29DIC, 74F04137437-001C14Capacitor, 270 PFC, 50 V, EMI Filter — 140006-271
30BIC, 74LS244137038-001C15, C16Capacitor, .1 (LF, 50 V, +80% -20%,

Ceramic 122002-104

30LIC, 74F74137436-001
30NIC, 74F138137521-001C17-C19Capacitor, .01 MF, 50 V, +80% -20%,
30RIC, 74F273137610-001Ceramic122002-103,
31BIC, 7418257137136-001C20, C21Capacitor, .1 uF, 50 V, 80% -20%,

Ceramic 122002-104

31DIC, 7418148137417-001C22-C29Capacitor, .01 UF, 50 V, +80% —20%,
3IC, CPU, 68EC020, 16 MHz, 100PQFP 137691-001Ceramic122002-103
31LEPROM, 512K x 8, 100 ns136094-0040€30-C35, C36-C58
31NEPROM, 512K x 8, 100 ns136094-0041Capacitor, .1 WF, 50 V, +80% -20%,

Ceramic 122002-104

31REPROM, 512K x 8, 100 ns136094-0048
31TEPROM, 512K x 8, 100 ns136094-0049C59Capacitor, 100 UF, 16 V, Electrolytic,
32BIC, 7418244137038-001Radial123013-107
32D, 32W IC, 74F244137502-001C60-C72Capacitor, .1 (IF, 50 V, +80% -20%,

Ceramic 122002-104

33BIC, 7418257137136-001c73,Capacitor, 100 pF, 100 V, +5%,
33DIC, 74F244137502-001Ceramic122016-101
33LEPROM, 512K x 8, 100 ns136094-0042C74-C248 Capacitor, .1 UF, 50 V, +80% -20%,
33NEPROM, 512K x 8, 100 ns136094-0043Ceramic122002-104
33REPROM, 512K x 8, 100 ns136094-0050CRIDiode, MV5053, Light Emitting131027-002
33TEPROM, 512K x 8, 100 ns136094-0051CR2, CR3_—Diode, 1N4001131048-001
34BIC, 74LS257137136-001
3B, 35)IC, RAM, 32K x 8, 70 ns, .6137615-070GND1,GND2 Test Point179051-001
35L,EPROM, 512K x 8, 100 ns136094-0044aceConnector, 2 Circuit, Header, 100 Ctr 179048-002
35NEPROM, 512K x 8, 100 ns136094-0045JAUDConn, 36 Ckt, .1 Hdr, Long179300-036
35REPROM, 512K x 8, 100 ns136094-0052JP13Conn, 15 Ckt, Hdr, 100 Ctr179118-015
35TEPROM, 512K x 8, 100 ns136094-0053JROMConn, 60 Ckt, Hdi, .1 x .1C179291-060
36BIC, 7418257137136-091JSYNC,Conn, 3 Ckt, Hdr, .100 Ctr179048-003
30wIC, 74F244137502-001JxConn, 60 Ckt, Hdr, .1 x IC179291-060
37EEPROM, 128K x 8, 100 ns136094-0223
37EPROM, 128K x 8, 100 ns136094-0224QI-Q3__Transistor, 2N3904133041-001
Q4-Q6Transistor, 2N5306133033-001
37k.EPROM, 512K x 8, 100 ns136094-0046
37NEPROM, 512K x 8, 100 ns13604-0047ReResistor, 1 KQ, £5%, 1/8 W110027-102
ADC.VREConnector, 2 Circuit, Header, .100 Ctr 179048-002RI, R2Resistor, 470 Q, 45%, 1/8 W110027-471.
RBResistor, 10 Q, £5%, 1/8 W110027-100
C1, C2Capacitor, 100 pF, 100 V, 5%, Ceramic 122016-101R4Resistor, 100 Q, £5%, 1/8 W110027-101
C3Capacitor, .1 WF, 50 V, +80% ~20%,RSResistor, 15 Q, 5%, 1/8 W110027-150

Ceramic 122002-104

4-23

Page 56

Cuaprer 4 — Parts ILLUSTRATIONS Moro FRENzy Mini-DRLUXE

Moto Frenzy Game PCB Assembly, Continued Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
ROResistor, 1 KQ, +5%, 1/8 W110027-102R88.Resistor, 470 Q, +5%, 1/8 W110027-471
R7Resistor, 2.4 KQ, 5%, 1/8 W110027-242R89-R100_ Resistor, 1 KQ, £5%, 1/8 W110027-102
R8Resistor, 470 Q, £5%, 1/8 W110027-471R101-R106 Resistor, 470 Q, +5%, 1/8 W110027-471
ROResistor, 10 Q, 5%, 1/8 W110027-100R108Resistor, 10 Q, +5%, 1/8 W110027-100
R10Resistor, 100 Q, +5%, 1/8 W110027-101R109Resistor, 1 KQ, +5%, 1/8 W110027-102
RuResistor, 15 Q, 5%, 1/8 W110027-150R110Resistor, 10 Q, +5%, 1/8 W110027-100
R12Resistor, 1 KQ, +5%, 1/8 W110027-102R12Resistor, 10 KQ, $5%, 1/8 W110027-103
R13Resistor, 2.4 KQ, +5%, 1/8 W110027-242R113, R114 Resistor, 1 KQ, +5%, 1/8 W110027-102
R14Resistor, 10 Q, +5%, 1/8 W110027-100R15Resistor, 10 KQ, 45%, 1/8 W110027-103
R15Resistor, 100 Q, +5%, 1/8 W110027-101R116Resistor, 1 KQ, £5%, 1/8 W110027-102
RIGResistor, 15 Q, 45%, 1/8 W110027-150R117Resistor, 470 Q, £5%, 1/8 W110027-471
RI7Resistor, 1 KQ, +5%, 1/8 W110027-102R118Resistor, 1 KQ, +5%, /8 W110027-102
RISResistor, 2.4 KQ, +5%, 1/8 W110027-242R119Resistor, 10 KQ, +5%, 1/8 W110027-103
R19Resistor, 100 KQ, +5%, 1/8 W110027-104R120, R123, R124
R20Resistor, 240 Q, +5%, 1/8 W110027-241Resistor, 10 Q, £5%, 1/8 W110027-190
R21Resistor, 0 Q, 5%, 1/4 W110005-001R125Resistor, 10 KQ, £5%, 1/8 W110027-103,

R126, Ri27 Resistor, 1 KQ, +5%, 1/8 W 110027-102 R22-R27_—Resistor, 1 KQ, +5%, 1/8 W 110027-102

R28-R35_—_Resistor, 470 Q, +5%, 1/8 W110027-471R128, R130-R133
R36-R41Resistor, 1 KQ, 45%, 1/8 W110027-102Resistor, 10 Q, +5%, 1/8 W110027-100
RA2, R43_—_-Ressistor, 10 KQ, +5%, 1/8 W110027-103R135-R139 Resistor, 1 KQ, +5%, 1/8 W110027-102
R140Resistor, 470 Q, +5%, 1/8 W110027-471
R44Resistor, 100 Q, +5%, 1/8 W110027-101RI41-R145 Resistor, 1 KQ, +5%, 1/8 W110027-102
R45Resistor, 220 Q, +5%, 1/8 W110027-221
R46, R47Resistor, 100 Q, +5%, 1/8 W110027-101R146Resistor, 2.2 KQ, +5%, 1/8 W110027-222

R48, R49,

R52-R59Resistor, 1 KQ, 5%, 1/8 W110027-102STESTSwitch, Slide, SPDT160040-001
R6O-R63_—_-Resistor, 470 Q, +5%, 1/8 W110027-471VCRConnector, 2 Circuit, Header, .100 Ctr 179048-002
RO66-R71Resistor, 10 KQ, +5%, 1/8 W110027-103WDOGConnector, 2 Circuit, Header, 100 Ctr 179048-002
R72Resistor, 1 KQ, +5%, 1/8 W110027-102
R73Resistor, 10 KQ, +5%, 1/8 W110027-103x2Crystal, 14.318M, Osc. Module,

3x .3DP 144009-001

R74-R77Resistor, 470 Q, +5%, 1/8 W110027-471
R78-R81Resistor, 1 KQ, +5%, 1/8 W110027-102
R82-R86Resistor, 470 Q, +5%, 1/8 W110027-471
R87,Resistor, 10 KQ, +5%, 1/8 W110027-103

4-24

Page 57

CHAPTER 5

Schematic Diagrams

INTRODUCTION

WY, HIS CHAPTER contains the schemat- tion, this chapter includes wiring diagrams for

|. ic diagrams for all the Moto Frenzy” the entire game, the coin doors, the JAMMA

Mini-Deluxe printed-circuit boards, power supply, and the Hitron and Peter Chou

including the game PCB (also switching power supplies.

called GX2), the JSA ITI PCB, The PCB assembly drawings

the CLARN PCB, and the are illustrated in Chapter 4,

JAMMA Filter PCB. In addi- Parts illustrations.

Page 58

(CHAPTER 5 — SCHEMATIC DIAGRAMS Moto Frenzy MiNi-Del

awe COND? JAe¥M-1 0O——— 00 OND) JAMMR-2 0» CAD Co) JrR-3 O———$— +5 (259) Jar 09 +59 C5y) Jews O23 es2y) JRER-G O———a r12v REY aE OW CeONTRL] Jevee-8 Oa ENTE. CCHLOCKL) JARRR# O- CSPKRI* ) JReRHA-I0 O———— SPrReL (CAuD* > JeBe-1: O——— SPR ERED) Jerane-12 0——— RED. COLUED Jrewa-13 o-———« BLUE VID OND> seeeia-14 o———s vIDoND. CSELFTEST) Jevwen-3 O————e SELFTEST CCOINL) vAtw-16 O———— COTM CSTARTL) RR-17 O———= STRTS ‘CUPLAD JneHR-18 C+ UPS DOWNLAD JAFeIR-19 O———— Dnt CLEFTLAD veeew-20 Oe rt CRIGHTLAD JePRA-21 Oe art CuBUTTONL? Jeen-2e Oe ACTER CLaUITONZ) JeewR-23 0———-* ACTEL CLBUTTONAD JAPBR-24 O———e CTCL CLEFTLBD JARWA-25 O————e ACTTLL GRIGHTLB JeR@MA-26 O——— ACTTAL COND) Je@-27 O-————# OD COND seewR-28 o———= OND

5-2 Jaws oND> Jate-AO———+ Ow COND? arest-B O-———+ ond CoS) srue-¢ @———a osu +803 danen-p O——* +39 ©2503 Janee-e 0+ “sy C120) Janen-F O————+ 120 REY JRHAR-H O- CONTR? JRR-) Oo CORTE CCHLORKRD JAPPRRK O- CSPRRI-2 JRFPH-L O——— SrRR-L AUD CAD) JReeA-n CO SPRR-R CGREEND JRMA-N O———- GREEN SYNC) JAnPR-P O————» CORFEYRE™ SERVICE) saHA-R O———— SERVICER TILT? Jaten-s O———* TILT CCOINR? JarwR-T O-——— CoTNR CSTARTR) Jae) 2 ——— STRT2 CUPRA) Reewn-v O————# uP2 CDOMNRAD RFE O———* nz. CLErTRAD Jpwm-K O——— LF2 CRIGHIRAD jprei-Y O———s #72 CRBUTION: ) JAKWA-2 O———- ACTA? CREUTTONZ3 JRHMA-AR O———— CTE CRBUTTONS) saevNR-B) O———— acTc2 CLEFTRE) Jemme-CC O———— ACTTLZ CRIGHTRBD JaMR-DD O———-* ACT TRE COND? JAMNB-EE O————a AD CONDD aRemR-FF GO ———# GND

Pu/rac U3 15 o—sactrRa Ww o—encrn 13 o—eactes 42 O—eacrTes 31 Oe actA 10 o—eRr2 Oar 3 o—=pn8 7 o—uP3 boa sraRTs $0-—=CoIn? ¥o—e seavices 20—2-w 1 oO

asic 1 0—snsinc.0ur 2 os usync.ouT 30 VID

ANBUF SPRRER SPAR CONTR

ay sy. TSTPT_NS wet ow ese TSTPT NS 00/36 ee ae a ow? ow. acid TSTPTNS baad

oor © HE rae OO Fie oe, me . OE rove Rio woe ne rao “OME rue Ot oe ne 1-0 FR vue O ithe ns tT rite wou t © Fre woe ——— Fig woe

aise 22K ow

Page 59

Moro FRENZY Mini-DELUXE “ CHAPTER 5 — SCHEMATIC DIAGRAMS

oy att ron sop 3388353 SRUBRECE TEE ERES

Pre,

pratt, peso

PR +8 PRs vey dial 70 ped eet ree LS ow *

PRONE Rzsg Rave nie & R18: a FR Fax Fak io) nuar gRia7 Leis Tr) Feo mw Fix Fix

Pre 8 F656 w creed 1" may EPR Fe6 oat PR =—

Figure 5-1 Moto Frenzy Mini-Deluxe Game PCB (GX2) Assembly Schematic Diagram 4049809-XX C

5-3

Page 60

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 61

Moto Frenzy Mini-Deiuxe @ CHaprer 5 — SCHEMATIC DIAGRAMS

xoc0:399

asi R82 uss dun Faas Tres Rio# Rea $Ri06 PLD SS a Ca SC LR AC 7

a3afsAEE

an Hs a a a wat Fa 1 ws i eG ecrtss fA

car dew Len Len Lose wor TP ye 1h Fe

sr — wx bas fee fou bev fue dam dae : sro B70 so F570 Baa Fam Faro F570 were isd

veinsrayaaaoy BR
canatagHelis ws
cite:EaSeLs
bicurePus EXER “IK3/27 xo

a Sy

ar=Hie

oy dey tes Lee Lew hee Ley Len Lee

TTeTTo

ae ae parse a Pe wHe— 220 wocux AS oe ce e, [els ner

row enc #20. EOC

Ym re = mM SE

Eatete

ae : a S seo Yd e LOK yy, ROT 28 | Tyo p2 BS emote. upd cael 2 ts ai AE HOt

=—_=
FetineAe

laos Fos ow conan Fama ww

coor—.ani
cee cutBoaoa;aT!
teoe=

et wt

‘yonsms

Laas RSG Pe ‘

veeBeszoe00
FR cewreconteowe

cxoet

Figure 5-1 Moto Frenzy Mini-Deluxe Game PCB (GX2) Assembly Schematic Diagram A049809-XX C

5-5

Page 62

(CHaPTER 5 — SCHEMATIC DIAGRAMS % MOTO FRE: ZY MIxI-DELUXE

5-6 mm

our

BEE2RIER

se aaa wl ate ead fhe rae gaye ab ike “ioe wee GX cr vcrera rama! Pla = vam

sree OUT

xe 283 7 ior aid oo

figure 5-1 Moto Frenzy Mini-Deluxe Game PCB (GX2) Assembly Schematic Diagram AOA9809-XK C

Page 63

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 64

Cuaprer 5 — ScHEMATIC DiAGRAMS % MOTO Frenzy MINI-DELUXE

g ae i a iin

i

+

ono.

ow a

= corre

corr,

oo

GND AND AGND TIED INTERNALLY NEAR MSM6295

5-8 A Tee yap sor Ina 3/28 ssn tee ye} 44S sps ag 1 soe useae wee ua i fngya[t—e 09 4itn3 3-2 —ss0e Sele yep aso. Grad 508 sean

Page 65

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 66

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 67

Moto Frenzy Mint-DELUXE CHAPTER 5 — SCHEMATIC DIAGRAMS:

sets ese ROE coe tg Shoo 1 8 a

n»ines3
sass]oe At aos

Suze] tr var Perm sme aa

Seine] te iva teomcsrBetea

emo] is ives gene suse eugs—tfis tos Sama x suiee—2its 1703 2 Saaee

coon] te ioe Hosena.ayn
‘SRWnOL2aT

sorettan sdf. ona apes 7 me,

fiedsas 4460core
pidspssfoooom:

sorta vena

aRSteet a5oxrers
TREKsore—Hi20oxee
70soe2139REE

i SX eel sera 0 nyt ET!

=

. 11938

cunii93

eral re F Tliv isk, She on Ht a or Zhi yor BES tra Si. oc AES crassa woes] i3 ts DE oe Hrme—tl ts oe ee mes] th ion = Ree recto] ie oe Hoa come Gt Bae sooner

Figure 5-3 JSA Ili PCB Assembly Schematic Diagram A048973-01 D

5-11

Page 68

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 69

MOTO Frenzy MINI-DELUXE “ CnAPTER 5 — SCHEMATIC DIAGRAMS

Ray 33K ‘acu

Figure 5-3 JSA III PCB Assembly Schematic Diagram A046973-01 D

5-13

Page 70

CHapTeR 5 — SCHEMATIC DIAGRAMS MOTO FRENZY MINI-DELUXE

5-14 Q i © Hic He i O MME we @ M3 © Hig Hoe ms

ATG HOLE

oo © INE woe

Lose 45 UxOaL

[a7 x09 | 18 Uxo8 Voo = Lesu

Page 71

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 72

‘Cuaprer 5 — SCHEMATIC DiaGraMs “% Mo7o Frenzy Mixt-De.uxe

5-16 cara ” ons ve enrme— lea Femeee | vp aerss ever ae sce——hji8 2 saune—Shia bana tes e— eleva nective e—— ens? Fass sz paral, Toe poe sch 20—=scRL 3 0—= ow ee ker 6 Oe Fs 7 oer 0 ont 10 0—s oar. tooo

Page 73

Moro FreNzY Mint-DeLuxe & CHAPTER 5 — SCHEMATIC DIAGRAMS

na: ane

a Tier TT Ti on

a0

Loney Y 3 o—e sos So—esmz $ 0—eraToR, 6 O—avaTone, 7o—e0a 2 o—euy eee ’

7G

COMM LINK ty

Figure 5-4 CLARN PCB Assembly Schematic Diagram

A050273-XX A

5-17

Page 74

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 75

Moro FRENZY MINI-DELUXE CHAPTER 5 — SCHEMATIC DIAGRAMS

Ji-4 JAM-A Ja-2 JAN-B

2200PF

ycee=22000F

J4-8 TMG ste

+12Vcar=2200PF

Ji-6 $m rn sane

KET d7> ~< san-7

C26 2200PF J1-8 mm JAM-J

29 2200PF 4-9. str

c30=«2200PF

8-40. st oF

cat=2200°F

dhe 0 tt

c32=(270PF

J4-42.—- $M srr san L c33 270PF J4-13 = sar

c34 2200PF JA-48 1 stk

c35°=«2200PF

J4-18)— 9X sas > -3y

+12y C36 2200PF Ji 1 st

c37=2200PF

8-47 —— 1 satu

C36 2200PF J4-18 $111 Sv

c3a=2200rF

Jtt9 at

cio=2200Pr

4-20 PY TM _X sax k HA cu 2200PF Jt-24) 9 say

cue 2200PF 4-22 20 1 SZ

C43=2200PF

J1-23 TX 86

cHy 2200PF J4-24 $M st

cus 2200PF J4-25 MM 19191 Jaco

cHe 2200PF J4-26 1M. set HH KH

HH

RA Ji-27 JAM-EE

J4-28 JAM-FF

MHL

Figure 5-5 JAMMA Filter PCB Assembly Schematic Diagram 404729202 A

5-19

Page 76

Citaprer 5 — SCHEMATIC DIAGRAMS “% MOTO FRENZY MIXI-DELUXE

‘STER SHAKER CONTROL L—

g ‘1 vivojor | J] 28 8) 25] > [>-] al | af | os)! One<-oHnio = oR > 4 Se FR 4

8 ’ sesgesad? GPE 4 bs ; :

id ! 28 gE

5-20

Page 77

MoTo FRENZY MINI-DeLuxe CHaprer 5 — ScHEMaTiC DIAGRAMS

ay >]alo] > [25] Blo dA UE] fcc oc| | aEsed esr ekeo+es| eleores 833 5883 PBRERR 923383 ASSY AlddNS WWod / Add NOILNARESIO HaROd RAL FILTER

ty _fiteaaastt ith pas i clasts} opbld SS | WN

Figure 5-6 Moto Frenzy Mini-Deluxe Game Main Wiring Diagram

5-21 050337-01 A

Page 78

CHAPTER 5 — SCHEMATIC D1aGrams 4 Moro Frenzy MINI-DELUXxE

Lo fofofafafafah-p- dl | Una<cmoue >

WRK + +5 + xD oo

oo +12v +v

oPTION

oo

START {17 STEER

TuromE | 21

5-22

Page 79

Moro Frenzy Mini-Detuxe CHapTer 5 — SCHEMATIC DIAGRAMS

a je] 2/2) 21] 2 je

POWER DISTRIBUTION PCE (Jo. 8g

POWER SUPPLY ASS

Figure 5-6 Moto Frenzy Mini-Deiuxe Game Main Wiring Diagram A047292-02 A

5-23

Page 80

Carrer 5 — SCHEMATIC DIAGRAMS % Moto FRENZY Mint-DELUXE

it NC Fight Coin switch v nosNS 6 ax | Lett Coin Switch \ \ ' t NC ! [ OR NO~¢ BK \ swaND | 1)-BK 1 RIGHT con sw [2|-OR |__| LEFTCOIN sw |3 |

@np |7 a5V AC [8 CHASSIS GND | 9

Figure 5-7 Coin Door Wiring Diagram A037542-XX F

5-24

Page 81

AN ATARI GAMES

Location: Moto Frenzy” Mini-Deluxe Statistics Sheet

Date Recorded:

Left Coins: Right Coins: Auuiliary Coins: New Games: Continuation: Free Games: TAIT Meter:

Idle Ti Active Time: Solo Time: Linked Time: Error Count: Total Credits: Total Coins: Average Time/Credit: secs. Average Time/Coin: secs.

Histogram 1: Game times for Los Angeles track

0-29 30-59 60-89 90-119 120-149 150-179 180-209 210-239 | 240-269 270-299 300-329 330-359 360-389 390-419 420-449 450-479 480-509 510-539 540-509 570 & up Total Median STEELE] Histogram 2: Game times for Maui track

0-29 30-59 60-39 H-119 120-149 150-179 186-209 210-239 240-269 270-299 300-329 330-359 360-389 390-419 420-449 450-479 480-509 510-539 540-569 570 & up Total Median TEE Histogram 3: Game times for Utab track

0-29 \ 30-59 60-89 90-119 120-149 150-179 180-209 216-239 240-269 270-299 300-329 330-359 300-389 390-419 420-449 450-479 480-509 510-539 546-569 570 & up Total Median HUTTE

Continued on back page &

Page 82

A ATARI GAMES

Location:

Meter: Moto Frenzy” Mini-Deluxe Statistics Sheet, Continued

Date Recorded:

Histogram 4: Game times for Las Vegas track

0-29 30-59 60-89 90-119 120-149 150-179 180-209 210-239 240-269 270-299 300-329 330-359 360-389 390-419 420-449 450-479 480-509 510-539 540-569 570 & up Total Median HTT Histogram 5: Game times for Kenya track

0-29 30-59 60-89 90-119 120-149 150-179 180-209 210-239 240-269 270-299 300-329 330-359 360-389 390-419 420-449 450-479 480-509 510-539 540-569 570 & up Total Median TTP Histogram 6: Game times for Norway track

0-29 30-59 60-89 90-119 120-149 150-179 180-209 210-239 240-269 270-299 300-329 330-359 360-389 390-419 420-449 450-479 480-509 510-539 540-569 570 & up Total Median ELITE

Page 83

pele pelel elated pele ele fel el pele fel fel feted pelfeal ele el pele feted pelfelel feted [ca]

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displ: and video-dise players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective:
  • Such products are returned prepaid to Seller's plant, and (oc) Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse. neglect. alteration. improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits. loss of use, incidental or consequential damages. Excepl for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terns berein, this warranty is expressed in liew of all otber warranties expressed or implied. including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor autborizes any otber person to assume for the Seller any other liabilities in connection with the sale of products by Seller. Pre Eee eee eel eel ele erate elrelelrelrel elated ele ele fel elfel feted

ele el elle elel ele ele pele pel el ele pele pelea el fel el felrelfelrel el (ca)

The use of any non-Atgui parts may void your warranty, according to the terms of the warring: The use of ny non-Atui parts may also adversely affect the safety of your ot Be very cautious in using non-Atari-supplied n order to er your safety game and cause injury (0 you components with our games. Atari distributors are independ being privately owned and operated. In their judgment they may sell parts or accessories other than Atri parts or accessories. Atari Games Corporation cannot be responsible tor part or any modification includi © quality. suitability or safety of any non-Atari bor which is performed by such distributor

Page 84

A

ATARI

GAMES

ATARI GAMES CORPORATION

675 Sycamore Drive Milpitas, CA 95035 ae