CATHODE RAY TOMES

Indy 500 Twin Quick Start Guide

INDY 500 Twin (Revision A, Newer) (Sega, 1995) · Document · 2 pages · original scan

Page 1

Quick Start for Easy Installation

The following information is provided to aid in the installation of the INpy 500 Twin game. For complete instructions, field service, and maintenance, please tefer to the Invy 500 Twin Owner's Manual.

  • Uncrate and move the Inpy 500 Twin cabinets to their final locations. Use four (4) 4 people to uncrate and move the | Inpy 500 Twin cabinets. See the | figure for minimum installation | dimensions.
  • Inspect the Inpy 500 Twin cabinets inside and | out for damage. (The Coin | Mech Door key is tied on the | Controls. The rest of the keys are | hanging behind the Coin Mech | Door.) Contact the distributor for instructions if damage is found. | Remove the blue trim protector from all silver trim strips.
  • Remove the top two bolts and washers from the right-side cabinet, hang the Cash Box Tower on the right-side cabinet, and attach the right-side cabinet to the Cash Box Tower using the four bolts and washers (some tools in the cash box). Connect the right-side connectors.
  • Attach the left-side cabinet to the Cash Box Tower as in to step 3, using the attached hardware (some tools in the cash box). Connect the left-side connectors.
  • Adjust the six leg levelers on the Cabinet until the Cabinet is level and the two casters are at least 5 mm above the floor. Install the joint plate between the left- and right-side inside Jeg levelers
  • Install the Billboard (packed in the cabinet) above the Marquee, using the twelve bolts, washers and L-brackets attached to the cabinet and billboard (some tools in the cash box).
  • Connect the linking cable at the back of the cabinet: red to RX, black to TX.
  • Plug in and turn on the Inpy 500 Twin game. The AC cord and switch are located on the lower rear of the cabinet.
  • Adjust the Game Board Default Settings as required. See the back of this Quickstart Card, and, for more details, see the Inpy 500 Twin Owner's Manual (shipped in the Coin Box).
  • Set the Control Range ("Volume") Settings. Otherwise, game controls will not work properly. For more details, see the INnpy 500 Twin Owner's Manual (shipped in the Coin Box).
  • Play the Inpy 500 Twin game!
WARNING! NEW FOR INSTALLATION Control Range (“Volume”) Setting Test must be performed for game controls to work properly. See Indy 500 Twin Owner's Manual, page 33.

© SEGA 1995 January 1996

Page 2

Recommended Game Settings

GAME ASSIGNMENTS GAME ASSIGNMENTS OPTIONS:

GAME DIFFICULTY NORMAL,

RACE MODENORMALGAME DIFFICULTY, RACE MODE, HANDICAP, ADVERTISE
HANDICAPONSOUND, ENGINE VOLUME, DEFAULT VIEW: Can be set
ADVERTISE SOUNDONas desired for game play.

COUNTRY USA

CABINET TYPETWINCOUNTRY: Set to USA.
NETWORK IDMASTER/SLAVECABINET TYPE: Set to TWIN.

CABINET ID 1/2 .

ENGINE VOLUME2NETWORK ID: Set to MASTER for left-hand cabinet of all
DEFAULT VIEW4linked cabinets; set o SLAVE for ail other linked cabinets. Set

© EXIT to STAND-ALONE for single cabinet (half of a TWIN configuration). CABINET ID: Set to 1 for MASTER cabinet; set to 2-8 for all

other cabinets. Do not number two cabinets the same number.

COIN ASSIGNMENTS >

TS OPTIONS: COIN/CREDIT SETTING #12 COIN CHUTE #1 4 COINS 1 CREDIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

COIN ASSIGNM!

The COIN ASSIGNMENTS menu allows changes to be made to the COIN/CREDIT settings and displays the corresponding COIN CHUTE #2 relationships between number of coins and number of credits. The 4 COINS 1 CREDIT

manufacturer’s recommended default COIN/CREDIT SETTING is #12. See the Indy 500 Twin Owner's Manual for deiailed information MANUAL SETTING > EXIT and instructions. SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON