Quantum CO-221-01 1st Printing
Quantum (rev 2) (General Computer Corporation (Atari license), 1982) · Change Order · 10 pages · 16 sections · original scan
0-21.01 1st printing
Supplement to
Operation, Maintenance, and Service Manual (TM-221, 1st printing) and Schematic Package (SP-221, 1st printing)
The attached sheets replace the following sections of TM-221:
Chapter 1 E. Setting the Option Switches Table 1-1 Switch Settings for Price Options
Chapter 2 B. Performing the Self-Test : a
Chapter 4 Figure 4-11 EMI Shield PCB Assembly and Parts List ATARI
EMI Shield PCB Schematic (supplements SP-221) © 2026 communes tons Company
E. Setting the Option Switches
Settings of the game price options are explained in Table 1-1. Options preset at the factory are shown by the <4 symbols. However, you may change the settings according to your individual needs. To verify option switch settings, set the self-test switch to the on position. Compare the information ‘on the screen to the option switch settings listed in Table 1-1. Then set the self-test switch to the off position. Table 1-1 describes the switch settings for options relating to game price, coin mechanism multipliers, and bonus play. These switches are on the game PCB at location 4C/D. The multipliers (switches 4-6) determine the value of the coin mechanisms to the game’s logic. A coin mechanism is a device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. After this inspection, Set-Up Procedures
the mechanism either accepts or rejects the coin. The coin door has two coin mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. For example, if you have a 2 DM/1 DM coin door, you may want to set the left multiplier at x2 and the right multiplier at x1. You may offer bonus play for certain combinations of coins inserted. For example, with the game set at $.25 per play, players who deposit four successive $.25 coins before pressing the start switch can receive a bonus play. The bonus feature encourages players to insert more money than the minimum $.25 required for one game. Table 1-1 lists switch settings for price options. The switches are on the game PCB at location 4C/D. Refer to Figure 3-7 to remove the game PCB.
Table 1-1 Switch Settings for Price Options
Settings of 8-Toggle Switch on Quantum PCB (at 4C/D) 7 6 5 4 3 2 1 Option
Off On
On On
Off Off Off On
On Off
On. On Off On
Ott Off
On, On
On On Free play 1 coin for 2 credits 1 coin for 1 credit 2 coins for 1 credit
Right coin mechanism x 1 < Right coin mechanism x 4 Right coin mechanism x 5 Right coin mechanism x 6
Left coin mechanism x 1 <4 Right coin mechanism x 2 Off No bonus coins < Off For every 4 coins inserted, logic adds 1 more coin Off For every 4 coins inserted, logic adds 2 more coins On For every 5 coins inserted, logic adds 1 more coin On For every 3 coins inserted, logic adds 1 more coin On No bonus coins On No bonus coins
“4Manufacturer's recommended settings
Self-Test Procedure
A. Comments on Troubleshooting
When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio |! printed-circuit board (PCB), or the video display? The next step is to check all harness wires and connectors to the suspected assembly. If you do not find a harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly. When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display fails, we suggest that a qualified video-display technician handle the troubleshooting and repair. Be sure to refer to The Book—A Guide to Electronic Game Operation and Servicing, published by Atari, Inc., whenever you need help with the techniques, tools, and terminology associated with coinoperated electronic games. To effectively troubleshoot a game PCB, learn as much as you can about the PCB. The diagrams in the Schematic Package (included with the game) show the functions of the circuitry. Again, while troubleshooting a PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram.
2-2
B. Performing the Self-Test
RAM and ROM Tests: RAM test occurs when you turn the game on. The test passes if the 1-player start switch is not lighted. If there is a failed RAM at location 2N, 2M, 3N, or 3M, the 1-player start switch will remain on. If there is a failed RAM at location 5D, 5E, 6D, or 6E, the 1-player start switch will flash on and off. \f the vector RAM and program ROM tests pass, the message RAM OK appears in the upper left corner of the screen. ROM test occurs when you turn the game on, after the RAM test passes. The ROM test passes if the 2-player start switch is not lighted. If there is a failed ROM, the 2-player start switch will remain on. Table
a lists the failed ROM and its location on the game
Table 2-1 Locations of Failed ROM
Failed ROM Location
Number on Game PCB
0,2 2E 1,3 3E 46 2F 57 3F 8,10 2Hid 911 SHId 12,14 2K 13,15 3K 16,18 at 17,19 3b
Select Function:
Wait at least 10 seconds after playing a game before entering the Self-Test Mode. Set the self-test switch to on to start the Self-Test. See Figure 1-2 for the location of the self-test switch. (To exit the Self- Test Mode, set the self-test switch to off.) When Self-Test is started, the Self-Test Menu shown in Figure 2-1 appears. Each time you press the 1-player start switch, a different function is highlighted. Press the 2-player start switch to select a highlighted function.
SELF TEST MODE
CHOOSE FUNCTION
STAITSTIOS
GRIOS AND CONTROL CHECKS
OPERATOR OPTIONS
PRESS ONE PLAYER BUTTON TO ADVANCE CHOICE
PRESS TWO PLAYER BU TO CHOOSE FUNCTION
Figure 2-1 Self-Test Menu Self-Test Procedure
Statistics:
Press the 2-player start switch when STATISTICS is highlighted and the Game Statistics screen shown in Figure 2-2 appears.
ONE PLAYER TW PLAYER COIN COUNT HIGH TIME AVE TIME HIGH RACK AVE RACK HIGH SCORE (2260 AVE SCORE o EDS q VES a bLGHT CAIN fa] orn
Figure 2-2 Game Statistics
To erase all statistics except the high-score table, return to the Self-Test Menu by pressing the 1- or 2-player start switch. Select OPERATOR OPTIONS. Set the STATISTICS option to RESET. To erase the high-score table, set HIGH SCORES to RESET. Resetting the high score table does not clear credits. To clear credits, turn the game off and then on. To return to the Self-Test Menu, set the selftest switch off and then on.
Self-Test Procedure Quantum
Grids and Control Checks: To see the Horizontal/Vertical Grid screen (Figure To see the Diagonal Grid screen (Figure 2-3), return 2-4), press the 1- or 2-player start switch. To return to to the Self-Test Menu and select GRIDS AND CON- the Self-Test Menu, set the self-test switch off and TROL CHECKS. The game displays the first of four then on. possible screens for this test.
Figure 2-4 Horizontal/Vertical Grid Figure 2:3 Diagonal Grid
The outside grid lines should touch the sides and corners of the video display. Roll the Midi Trak-Ball™ to change colors. Use this pattern for setting the purity and convergence adjustments as described in the color X-Y display manual. This pattern is adjusted, set, and sealed at the factory, and not operator-adjustable.
2-4
To see the Color Bar Pattern screen (Figure 2-5), press the 1- or 2-player start switch. To return to the Self-Test Menu, set the self-test switch off and then on.
YELLOW ORANGE
BRIGHT BLUE TURQUOISE PURPLE
Figure 2-5 Color Bar Pattern
This screen tests orange, yellow, red, white, purple, green, bright blue, turquoise, and blue for color and intensity. Each group of vertical lines has the brightest color on the left and the dimmest on the right. Use this pattern for setting the tracking adjustments as described in the color X-Y video display manual. Self-Test Procedure
To see the Game Switches screen (Figure 2-6), press the 1- or 2-piayer start switch. To return to the Self-Test Menu, set the self-test switch off and then on.
1-PLAYER 2-PLAYER START START
LEFT COIN MECHANISM RIGHT COIN MECHANISM AUXILIARY COIN SWITCH
COINS
TRAKBALL x 0000 y ooo
DIP SWITCHES 6 Ss 4 4 C a a
Figure 2-6 Game Switches
This screen tests game switches. Push and release the 1- and 2-player start switches and the auxiliary coin switch. Activate the left and right coin mechanisms, and roll the Midi Trak-Ball™. The corresponding 0 will change to 7 when the switches are closed. Option switch settings are shown at the bottom of the screen. A 0 means the switch is off. A 7 means the switch is on, Refer to Table 1-1 for an explanation of option switches.
Self-Test Procedure
Operator Options To see the SELECT OPTIONS screen (Figure 2-7), return to the Self-Test Menu and select OPERATOR OPTIONS. To move to the next option, press the 1-player start switch. To select a new value, roll the Midi Trak-Ball™ Press the 2-player start switch to replace the old value with the new value. Table 2-2 lists game options, their possible settings, and manufacturer's recommended settings.
SELECT OPTIONS
PRES ONE PLAYER BUTTON TQ Move TO NEXT OPTIUN
PRESS TWO PLAYER BUTTON TO REPLACE NLD VALUF WITH NEW
POLL TRAKBALL FOR POSSIBLE VALLES
OPTION CURRENT NEW
DIFFICULTY LEVEL 2 é
Figure 2-7 Select Options Table 2-2 Game Options
Manufacturer's
Option Possible Settings Recommended
Setting
| Difficulty Level | 1, 2, 3, 4,5 | 2 |
| Language | English, French, German, | English |
Spanish
| Lives perGame | 2,3, 4,5 | 3 |
| Signature | On, off, reset | On |
| High Scores | Keep, reset | Keep |
| Bonus 1 | First bonus at 0, 10,000, | 25,000 |
15,000, 20,000, 25,000, 30,000, 50,000
| Bonus 2 | Additional bonus every 0, | 50,000 |
10,000, 15,000, 20,000, 25,000, 30,000
Statistics Keep, reset Keep
| Cocktail Mode | No, yes | No |
| Coin Counters | 1,2 | 1 |
The SIGNATURE option allows the player with the highest score to sign his name using the Midi Trak- Ball™. His name and score are transferred into the high-score table. The entire high-score tabie is erased with the reset option. However, you may erase all except the three highest scores by turning the game off. To end the Self-Test, set the self-test switch to off.
Illustrated Parts Lists
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the specific ‘wnitlen permission of Atari, Inc., Sunnyvale, CA, This drawing is ‘only conditionally issued, ‘and ‘neither receipt nor possession thereof confers or transfers any right in, oF license to use. the subject matter of the drawing or any design or technical informa tion shown thereon, nor any right to reproduce this drawing or any par! thereo!. Except for manufacture by vendors of Atari inc., and for manulacture under the corporation's written license, ‘nc right fo reproduce this drawing is granted oF the subject mat ler thereo! unless by written agreement with or written permis sion kom the corporation,
Figure 4-11
4-22 Loci co C22 arg to cele In co aie oo i se ia TI a oo
- co a a ia ToT Go oD ao See co mre co oo an co 7 470 °F 470 PF oc co +}. 470 PF eee co ¢40L4D jn | trec2 Lssy
EMI Shield PCB Assembly
A037430-03 A
Quantum Illustrated Parts Lists
EMI Shield PCB Assembly Parts List
| Designator | Description | Part No. |
Capacitors
| C1, C2 | 0.1 pF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 | |
| C3, C4 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 | |
| C5 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 | |
| C6-C8 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 | |
| co | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 | |
| C10-C12 | 0.01 pF, + | 20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C13, C14 | 0.1 uF, +80, | -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C15 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 | |
| Ce | 470 pF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor | 122016-041 |
Acceptable substitute is part no. 122013-471
| Ci7 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C18 | 470 pF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor | 122016-471 |
Acceptable substitute is part no. 122013-471
| C19-C23 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C24-C34 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C35 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C36 | 470 pF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor | 122016-471 |
Acceptable substitute is part no. 122013-471
| C37 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C38, C39 | 0.01 pF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C40 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
Connector
| P20 | 44-Pin Card-Edge Connector Acceptable substitute is part no. | 179073-044 |
179046-044
4-23
J2o P2
+ov ReT [A aerb bet eee _Lwee fal
+sv [8 +
+sv [2 ++
esv ly t + SENSE [2! t
+22v/3 +
+Z2V 1K —P
-22V /4 +
- 22V|~_) ‘i
woaven $10. 3BV UNREC 2HORIZDY o|m +—}
2VERTOIR, IVERTOIR
(HORIZOIR
con
GND
CONAUX|
STARTZ
PLILED)
GND
GND
COINCONTR
ReD
YGND
GREEN eR PRR [z EI Slee
IVERTOUK
IHORIZCLI] & ZVERTCLK| 7
AvDIC+
PLLLED [14 o> ]o [se ful fe fs ]e[apofz |e Tr Ya [Ss 7z op fe pz Jo 2 oS Jd >
N
a
K comeconmyis XGROUNO 6}
Bue
xouT
YouT 1S
EMI Shield PCB Schematic (Supplements SP-221, ist printing)