CATHODE RAY TOMES

Highway TM-028

Highway (Atari Incorporated, 1975) · Technical Manual · 55 pages · 5 sections · original scan

Page 1

TM-028

Y Miahwuy

Service Information

° A ATARI’ Innovative leisure

14600 WINCHESTER BOULEVARD, LOS GATOS, CALIFORNIA 95030 « TELEPHONE (408) 374-2440 « TELEX 357-488

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

TABLE OF CONTENTS

Section 1 - General Information

Para Title 1-1 Introduction

1-2 Warranty 1-3 New Machine Set-up Procedure

1-4 New Machine Check Out

1-5 T.V. Adjustment

1-6 Coin Acceptor

1-7 General Machine Maintenance

Section 2 - Circuit Description

A. PLAY

  • Display
  • Controls

B. CIRCUITS

  • Power EE, FF-1
  • Game Time Circuits GGl, GG2, GG3

Timing Circuits DD4-8

Video and Syne DD1-3

Road Shaping

Speed Pulse Syne Lock BBS Analog Speed Circuit BB3, BB4

Data Accumulator BB5, BB6

Data in Register CC5

  • Memory Entry Control
  • Memory ww

O©OnrI OWN

  • Memory Read Circuits CCS
  • Road H Functions FE2, ER3
  • Traffic Motion Functions
  • Traffic Car Building Circuit
  • ME Steering Circuits
  • ME Car Motion Circuits
  • OFF Road and Crash Circuits
  • Score Counters Page 1-1

1-1

1-2

1-2

1-3

Lu

1-5

2-3

2-4

2—4

2-5

2-6

2-8

2-11

2-12

2-14

2-14

2-14

2-17

2-17

2-18

2-18

2-19

2-20

2-21

2-23

Q-24

Page 4

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 5

Para TABLE OF CONTENTS (con't.)

CIRCUITS (con't.)

  • Score Functions
  • Audio
  • Motor Sounds
  • Crash Sounds
  • OFF Road Sounds

TESTING

Section 3 - Customer Service Information

z b

@ won Test Equipment

Required Minimum Equipment

Optional Equipment

Logic Type and Function List Page

2-24

2-25

2-25

2-25

2-26

Page 6

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 7
  • GENERAL MAINTENANCE INFORMATION

1-1. INTRODUCTION

Atari video games consist of a cabinet, TV monitor, a printed circuit board (PCB) computer, interconnecting wiring, and various cabinet-mounted circuit components. Except for a schematic, no information about the TV monitor is presented in this manual. The TV monitor is a Motorola XM701 unit. TV circuit malfunctions can

be solved using standard TV troubleshooting techniques. However, the PCB computer requires troubleshooting techniques that may be unfamiliar to the average technician. Therefore, the troubleshooting information in the manual is dedicated to the PCB computer and its associated cabinet circuitry.

1-2. WARRANTY

This game has been designed with solid state circuitry to be as maintenance-free as possible. However, as with all devices mechanical or electrical, there may be minor problems. If the printed circuit board (PCB) fails within the 90-day* warranty period, contact the distributor from whom the game was originally purchased for replacement or repair instructions. All such warranty returns must be accompanied by completed warranty return forms. Any PCB repairs attempted by anyone other than authorized Atari Service Center personnel will void the warranty. If the PCB fails after the warranty period has expired, it will be repaired for a nominal parts and labor charge.

Atari, Inc. warrants the T.V. monitor for a period of 30 days commencing the day of shipment form the Atari factory. If the monitor fails within that period, immediately contact the distributor from whom the game was originally purchased for repair or replacement instructions. Any T.V. repairs (other than replacement of fuses or adjustments) attempted during the warranty period by anyone other than authorized Atari Service Center personnel will void the warranty.

*(From date of shipment from the factory) 1-1

Page 8

If the T.V. monitor fails after the warranty period has expired, it may be returned to the distributor where it will be repaired for a nominal parts and labor charge, or it may be taken to any competent TV repair shop.

1-3. NEW MACHINE SET-UP PROCEDURE

Before turning this machine on, inspect it carefully for any damage

which may have occurred during shipment. Inspect both interior and exterior of the machine for any obvious damage to the cabinet or internal components. Check for cracked or broken cabinet parts, assemblies pulling loose, broken or disconnected wires of foreign objects shorting electrical connections. After the machine has been plugged in and turned on, perform the checkout procedure.

1-4. NEW MACHINE CHECKOUT

As each new machine leaves the factory, every component and subassembly is carefully checked for proper operation. However, since parts may have been damaged or adjustments changed during shipping, the following checkout procedure must be repeated prior to placing the machine on location:

  • Inspect both the exterior and interior of the machine for obvious shipping damage such as cracked or broken cabinet parts, subassemblies broken loose, etc.
  • Carefully inspect the interior of the machine to see that all solder joints, slip-on connectors and plug-in type connectors are firmly seated. Pay particular attention to the PCB edge connector, the fuses and any connectors to the potentiometers. Also check the connections to the coin switch, the T.V. monitor, the interlock switches and all the other Molex-type connectors.
  • Plug the machine in, and pull out the white actuator shafts of the interlock switches if the rear door is open. Inspect the CRT (cathode ray tube) image for a steady and sharp picture which exhibits the proper levels of brightness and contrast. 4, Insert several old and new coins into the coin acceptor, No genuine coin should be rejected and each coin insertion should step the coin counter one digit. Depress the coin rejector button to make sure that the linkage is operating smoothly.

1-2

Page 9
  • Coin insertion should start the game. Check for proper game

sequence, making sure that all aspects of the game are functioning correctly.

  • The door locks should turn to the "locked" and "unlocked"

positions smoothly and the doors should open and close without binding. 7, The interlock switches must turn off the entire machine when the

rear door is opened.

1-5. TV ADJUSTMENT

The adjustment of the TV monitor functions like that of a normal TV set. The only exception to that is the audio portion of the TV is not used. The volume control is located on the PC computer Board. The monitor is adjusted through the rear door. a. Brightness: Adjust the brightness before the contrast. Adjust so that the CRT background is as dark as possible. Db. Contrast: The contrast is adjusted so that the images displayed on the CRT are as bright and clear as possible with out being blurred. c. Vertical Hold: The vertical hold should only be adjusted if the picture is rolling up or down the screen. Adjust

for a stable centered picture. c. Horizontal Hold: If the picture is slightly off center horizontally, if the images appear warped or if the picture is broken into a series of diagonal lines, adjust the

H Hold.

e. Vertical Size: Adjust only if the top and bottom of the race course is cut off from the visible portion of the screen or there is too much distance between the edge of the course and the edge of the screen which will appear as an extra set of horizontal dotted lines on the top and bottom of the CRT display. Adjust for maximum

picture size. f. Vertical Linearity - Change this adjustment only if the top of the picture seems compressed.

1-3

Page 10

g- The Yoke - The yoke should never need adjustment unless the adjuster has been tampered or damaged. If yoke adjustment is necessary, both yoke rings should be rotated simultaneously for optimum centering of the picture on the CRT.

1-6. Q-530 COIN ACCEPTOR: OPERATION, ADJUSTMENT & MAINTENANCE

All coin acceptors leave the factory adjusted for maximum performance. If, however, more critical adjustments are desired, or if the unit has been completely disassembled for service, the following adjustment procedure is suggested. If the coin acceptor has been removed from the machine, place it in a vertical position on a level surface. If the acceptor is still mounted on the coin door, place the coin door in a vertical position on a level surface.

a. Kicker and Separator

  • Set the acceptor with the back of the unit facing you in the test position.
  • Loosen the screws holding the kicker (1) and the separator (3) and move both the kicker (2) and the separator (4) as far to the right as they will go. Tighten the screws. ,
  • Insert several test coins (both old and new) and note that some are returned by striking the separator. 4, Loosen the separator screw and move the separator a slight amount to the left. Tighten the screw.
  • Insert the test coins again and, if some of them are still returned, repeat Step 4 until all the coins are accepted.
  • Loosen the kicker screw and move the locker as far to the left as it will go. Tighten the screw. 7, Insert the test coins and note that some are returned.
  • Loosen the kicker screw and move the kicker a slight amount to the right. Tighten the screw.
  • Insert the coins again and, if some are still returned, repeat Step 8 until all the coins are accepted.
  • Be sure that both screws are tight after the adjustments have been made.
Page 11

b. The Magnet Gate

  • Set the acceptor with the frcit of the unit facing you in the test position.
  • Turn the magnet gate adjusting screw (2) out (counterclockwise) until none of the coins will fit through.
  • With a coin resting in the acceptor, turn the adjuster in (clockwise) until the coin barely passes through the magnet gate. 4, Test this adjustment using several other coins (both old and new) and, if any of them fail to pass the magnet gate, repeat Step 3 until all the coins are accepted.
  • Fix the magnet gate in this position with a drop of glue or lok-tite, if necessary.

c. Acceptor Maintenance

Depending on the enviroment in which the acceptor is used, periodic preventative maintenance should be performed. The mainplate (5) may be cleaned with any household cleaner. Thorough rinsing and drying are necessary to remove deposits and/or film. Remove all metal particles from the magnet by guiding the point of a screwdriver or similar tool along the edges of the magnet. You will notice that the particles will cling to the point of the tool. Remove the transfer cradle (9) and the undersize lever (10) and

clean the bushings and the pivot pins. A pipe cleaner is an effective cleaning tool. Apply powdered graphite or pencil lead to the pivot pins and bushings and reassemble. Spray the entire unit lightly with WD-40, a silicone lubricant.

1-7. GENERAL MACHINE MAINTENANCE

Due to its solid state circuitry, your machine will require very little maintenance other than peridoic cleaning, lubrication and T.V. monitor adjustment. The cabinet and plexiglass screen may be cleaned with any non~abrasive household cleaner. The coin acceptor and the rejector linkage should be sprayed lightly once every three months with WD-40 or similar silicone lubricant. The potentiometer shafts must never be lubricated in any way. The T.V. monitor is adjusted only when the CRT picture is distorted, or if the contrast or brightness appear to be out of adjustment.

1-5

Page 12

KICKER SCREW KICKER SEPARATOR SCREW SEPARATOR MAINPLATE ASSEMBLY GATE ASSEMBLY COVERPLATE ASSEMBLY RAIL CRADLE ASSEMBLY UNDERSIZE LEVER MAGNET GATE ASSEMBLY MAGNET GATE ADJUSTER SCREW LOWER GATE PIVOT SPRING UPPER GATE PIVOT SPRING GALE PIVOT PIN WIPER LEVER SPRING WIPER LEVER 18 WIPER COIN ACCEPTOR — EXPLODED DRRECR I Semen

COIN MECHANISM — EXPLODED

1-6

Page 13

Seetion 2 - Circuit Description

HIGHWAY GAME

A. PLAY

  • Display

' i —S 6} «1-5 > 2-digit score fo \ we . m7 C _ | With me traffic ) 40 _ 7 ME car 2 NN Against me traffic }

  • Controls i Coin Slot

Steering Wheel

Accelerator

Page 14

The accelerator moves the road down. The steering wheel controls the ME car.

The ME car stays at the same relative vertical position in the lower half of

the screen. Motion is the road moving down. If the car is off the road,

only slow movement is allowed. On the road the ME car accelerates to a

maximum speed.

The shape of the road is random. It can turn left or right to a maximum of

45 degrees. The digital memory for shaping attempts smooth curves. Because

digital is quantisized, there is some jaggedness at the edge of the road.

The shape changes as a function of distance moved (not speed).

In the Attract Mode, the ME car is turned sharply to the right and moves in

that direction as the road moves down. It does not stay on the road and when

it reaches the right edge of the screen it disappears for a moment and

shortly reappears at the left edge (still moving to the right)

In the play mode there are motor sounds from idle to full speed. OFF the

road a graty beep-beep sound is added. Only relative slow speed is possible

OFF the road. When hit by traffic a pulsing crash sound occurs while the

ME car is pushed aside and motion stops.

Scoring is clocked off as distance travelled. A good score is possible only

if you stay ON the road and avoid getting hit by traffic.

Page 15

CIRCUITS

20.

21.

22.

23.

24. Power (EE, FF-1)

Game Time Circuit (GG 1, 2, & 3)

Timing Circuits (DD 4, 5, 6, 7, & 8)

Video and Sync (DD 1, 2, 3)

Road Shaping (AA and BB 1-8)

Speed Pulse Sync Lock (BB5)

Analog Speed Circuits (BB 3 and 4)

Data Accumulator (BB 5 and 6)

Data IN Register (CC 5)

Memory Entry Control (1024 Bit S.R.) (CC 6-8)

Memory (1024 Bit S.R., Gate Fl) (DD 6)

Memory Read Circuits (CC 5)

Road H Functions (EE 2-3)

Traffic Motion Functions (FF 7-8)

Traffic Car Building Circuit (EE 7-8)

ME Steering Circuits (EE 3-7)

ME Car Motion Circuits

OFF Road and Crash Circuits (CC 4-5)

Score Counters (GG 6-8)

Score Functions (FF 6)

Audio (BB 1 & 2)

Motor Sounds (BB 2 & 3)

Crash Sounds (BB 3 & 4)

Off Road Sounds (BB 2)

Page 16

Power - EE, FF-1

Normally it is expected that +5 volts for the logic will be obtained

from the TV set. It then comes in on the +5 volt terminal. In the

event that we do not want +5 volts, we can use +10 volts unfiltered

from the TV, That means a jumper is placed in a diode detail and

+10 volts come in on one of the terminals (AC for 5 volts). The

other alternatives provided for are AC center tap transformer or

AC bridge rectified transformer.

+15 volts has its own rectifier and regulator (LM340T-15) section.

Bridge and center tap alternatives are provided for. Another alter-

native for 15V regulation is to use a LM309 and associated

network.

Game Time Circuits - GG 1,2, &3

Game time starts when voltage is applied to 4.7K via input terminal,

The coin counter is also connected at this point. The diode to

+5 volts holds inductive spikes down,

Voltage must be at the input long enough for the 1 ufd cap to

integrate up to transistor conduction. When this happens, FF of F9,6-8,

74132 hysterisis gate is set. The hysterisis gate also helps guard

against spark false starts. The set of this FF is GAME TIME.

Page 17

GT true releases 555 to pulse. The 555 pulses are counted. 8 counts

is a game. The terminal count resets GAME FF via gate Fa... A

transistor is also connected to the reset gate to assure reset when

power is applied or when there is an interruption in power.

If the EXTENDED GAME FF, F7q gets set during the course of a game, a pulse is generated to restart the game counter from ZERO (via F8¢). The last 1/8th of game time is sensed to generated a score flash

functions (08,).

Timing Circuits (DD 4-8)

Timing functions use 12.096 MHz crystal for simple countdown to H

frequency. Interlace is not used in V. The end of the H countdown

is at H sync. The V countdown goes to 128V which is decoded to

V sync at DD 3. Countdown is continued to 8F for flash functions.

Page 18

Video and Sync DD1-3

Composite video is constructed to be compatable with Motorola and

Ball Brothers T.V. monitors, Motorola TVs as used in prior Atari

games have had internal blanking of H and V retrace and internal

separation of synchronization from composite video, Ball Brothers

monitors have neither of these and require separate H and V sync as

well as a properly blanked video signal.

Composite video is constructed for Motorola monitors and a separate

output is provided. Video without sync, but with blanking, is

provided for the Ball Bros. monitor, 0-5 V.

A new video structuring method is used. Construction is for 3

levels of video: (1) Black

  • Medium (medium white)
  • White - this appears intensely white whether written an a black or medium background.

Two open collector outputs provide this video capability. These are

from gates 594 and J9. This is similar to gate A and B in the 12° following circuit:

+5V

4 R56 AUD Video ” R57

ms 12 13! 1B sy Jg Figure g

Page 19

Here video will be black if gate A is down (zero volts). Video will

be medium if gate B is down (2.5V). Video will be white if gates

A and B are both up. (5 volts).

Blanking is new to Atari games, but here it dominates. V blanking

is constructed in latch F7 (DD 3) and horizontal blanking in latch

P3 (DD 5). These are ORed to form composite NOT blanking in gate

H7, 7402 (DD 3). Blanking forces gate K9g and K9,, up. This makes

the output of gate Kg. go down forcing black and deleting all other signals. When blanking is OFF, background and black level are routed

through negative OR gate N. 3 (DD 2). The resultant video switching

is between ground and 2.5V (because gate 3955 is down).

White signals are already OR when they input (+ true) to gate k91]- (ME car + score). These signals are down at K3y and 3943 and force

the output white.

The above provides video with blanking at levels satisfactory to

Ball Brothers' video needs. Additional resistor matrixing inserts

sync for Motorola. (R58, R60, and R59).

When sync is present the Ball Brothers output is already shorted to

ground by blanking and thus there is no sync interference to the

Ball Brothers' output. Without sync the Motorola output would swing

from +5 volts to +2.5 volts with medium level at 3.75 volts. R60

adjusts the amount of sync that is added below blanking. 30% of the

total swing is the value with given resistors.

Page 20

Road Shaping

General principles: We desire to keep the shape of the road in

digital memory. To do this we remember the top of the road in an

8=bit left/right counter C5 and B5 (AA 3-4). To change the road's

shape we increment or decrement this counter. These changes are to

the top of the TV display only. The second line down from the top

is as the road was before a motion function made a new entry. Thus

we have top of picture memory. A 1024=bit shift register is used to

remember each incrementation or decrementation as it occurs. Thus a

"stopped" road starts somewhere on the top and is apparently shaped

as we look down. Sensible shaping necessitates a program. This

program states that we will stay on the same slant for at least 8

lines. (Counter C6, BB 6). The program also states that when we

change to the next slant we change only to the next angle. There are

& different slants to the left and 8 to the right. For example, when

we change from #4 to the left (for 8 lines), the next possibilities are

no change (#4L, or #3L, or #2L). Any greater change would not be

smooth in appearance. This sequence of angles comprises a curve.

The basis for a new entry to the top of the road is motion. Motion is

defined by advance pulse. In this system we cail these advance pulses

"speed pulses" (SP). Distance travelled is determined by the number

of these used. Speed pulses are generated in analog speed circuits.

These are conditioned (BB 7-8) for synchronization and to limit the

number to a maximum of 3 per field. The conditioned speed pulses are

the input to the Road Shaping Circuit (A + Fég).

Page 21

Specific Operation: Road direction and slant are stored in £7 (74193,

BB 7). The direction is the most significant bit. For a right curve,

the least significant bits show up unaltered at the outputs of

exclusive gates £6, £64)> and F6,, 1000 to 111). For left cruves,

the direction bit changes, thus inverting the output of the exclusive

gates. The result is again 000 to 111. The effect is that direction

and magnitude signals are available. The magnitude will not wrap around

from input (count inputs) because the borrow output (pin 13) is

inverted and fed back to clear (pin 14). This means that after count

has reached ZERO a countdown pulse will not be accepted because it is

overridden by a reset (to ZERO). Conversely, the carry output (pin 12)

is connected to the load input (pin 11). Since the inputs (pins 15, 1,

10, and 7) are pulled up, an attempt to wrap around after the counter

is full reloads Full count and wrap around is not possible.

The number in the slant store defines slant by programming pulses in

each 8 line interval. The 8 Speed pulse interval is counted by C6

(BB 6, 7493). The units that are represented by an incrementation or

decrementation are one part in 256/ This is to the right or left.

Only one can occur per line and since there are 256 lines, 45 degrees

is the maximum slant the road can have.

Curves are made up off slanted sections that are changed by no more

than one unit slant every 8 lines. A ZERO slant store means that no

shift will be made. The number of increments or decrements that occur

is the result of the gating program of gates D6, D6),> and 06, (AA 5).

Page 22

These gates are enabled by the 4's, 2's, and 1's bits of the slant store.

The 4's bit permits 4 increment or decrement pulses to occur per 8 lines

if it is ON. The 2's bit permits 2 pulses to occur per 8 lines, and the

1's bit permits only one pulse to occur per 8 lines. The pulse source for

gating is the ORed (tied together) open collector output of C7, 74145,

BCD to decimal decoder. The output of this system is at 7410, D515 AA 5. From here it goes to increment the top of the picture, C5 and

Bb, AA 3 and 4, and to the data accumulator F5, BB 5. The count pulse

to the slant store E7 forms the curves. No more than one count pulse

can occur per 8 lines as limited by decoding of counter C6 at BB6. The

forming of curve is a random program that at each 8 lines decides

whether to make a change and if so whether the change be left or right.

The direction of the next change is stored in C8ys 7474 (AA 7). If the

road is to the FAR right and going right, FF C8, is forced left via PRESET input from gate Bo... Conversely, if the road is far left and going left, gates Ades B81 reset FF C8, to force direction back to the right. This direction force is necessary to keep the road generally

centered on the screen. Most of the time the direction FF is under

the control of random programming via FF, (815 which determines direction (as discussed) and FF, C8, which determines whether or not

to make a change (duration of curve). For RANDOM pulses we use RFX

and RFD BB 2 and 3 which are functions of motor cound counters. This is

totally random with respect to the synchronous system because they

count unprocessed speed pulses. Processed speed pulses can use only 3

per field and these must occur in the first half of the picture.

While RFD is a divide by 2 of RFX, they are independent if read together

at random times.

Page 23

FF 8, controls the curve-making process. It decides the duration of a

particular curve and whether there shall be a curve or not. There is

no change of direction except when control FF C8, has just flipped up. (Clocking FF C8q).

The pin 2 input to FF C8, is a random number (generated in unprocessed

speed pulses). This random number is interrogated when FF C8, is

clocked via BB,- The time up (pin 5) is time when no change is

permitted. During down time change of road slant is permitted. Thus

the character of the road is determined by the ratio of these times.

Function F (X) and F (Y) control this. F (X) is 8 times faster than

F (Y). This means that change is permitted only half the time. This

also means that a curve is maintained for seven-eighths of the time.

Speed Pulse Sync Lock (BB 5)

The purpose of this circuit is to retime the random speed pulses.

They enter the sync lock circuit at pin 4 of Foe. The synchronized speed pulses are restricted to the top half of the pix by 128V at D5,.

XPP are pulses 4V long generated in forming vertical sync (DD 3). There

are 4 of these in the upper half of the pix. They are routed through

inverter DI5 to gate 054 and the output speed pulses occur at pin 8 of

Fé. The 7474 is the random speed pulse detector. If a random speed

pulse is detected, the next synchronized pulse is permitted to pass in

full. The set input is the detector. It cannot set the FF if the

random pulse comes up in the middle of a timed pulse, however any

random pulse that occurs between latch gates the FF and the next

timed pulse through in full. Three pulses per field is maximum speed

as far as the digital circuits are concerned. After 3 pulses have been

Page 24

detected, the reset input to the FF H6g is held down (from pin 8, gate Aa - CC 7).

Analog Speed Circuit - BB 3 & 4

Timer 555 (BB 3) pin 3 output is of random speed pulses (negative true).

The pulses duration must be less than 4V so that they can be properly

retimed by the digital circuits. R22 and C18 determine this time. The

rate at which the pulses occur is determined by the collector current

made available by Q4. Since countdown of speed pulse generates motor

and crash sounds, the 555 must be operating even when motion is stopped.

The minimum current supplied by Q4 is determined by resistor divider

R47 (47K), R42 (1.2 meg) and R43, emitter resistor. The combination

places a voltage current to the 555 that is independent of transistor

beta. Diodes CR7 and CR8 are connected to compensate each other for

temperature variation. To get idle sounds without road motion, it is

necessary to detect when the speed pulse rate is below a certain

threshold. Devices NB, K9, H9, and NB, are digital rate detectors to do this. It had been determined that good idie sounds occur when

the spacing between unprocessed speed pulses is more than 8 ms. This

is the threshold that the digital rate detector is set to. FF NB, and

N8, are reset to ZERO by V SYNC. After that they can count to 3, but

no further. If at the next reset time they have counted to 3D, FF sees

jt and holds the GO level. On the other hand if the count of 3 is not

reached, D FF H9 sees this too. The generated GO signal controls the

input to the digital S.P. Sync lock at BB 8. GO signals are also

overridden during crash by the set input to DFF.

Page 25

For speed in excess of idle, the voltage of R47/R42 divider is forced

lower. The basic manupulation of this voltage is to the charge on

C17 220 mfd BB4. If this charge is greater than the divider voltage,

we have idle. QI is the crash transistor. It is connected to +15V

in order to pull the charge up as fast as possible. When a crash

occurs, 7406, B9,, turns Ql ON and the charge rate is limited only by

R39. C16 10 mfd holds the crash sound ON for a second or so. Q2 is

the OFF-the-road speed limit transistor. It is operated by 7406, B9,.

When the transistor is turned ON it limits the low voltage on C17 to

a value established by the ratio of R32 and R30, Diode CRI7 prevents

this circuit from swamping the crash input. When neither crash nor OFF

road charge is being supplied to C17, the idling voltage of C17 is

kept near the threshold of change by divider R37 1K and R36 10K, BB 5. When gas is applied, C17 discharges through R33, 33K. This resistor

determines the acceleration rate. When foot is removed from gas pedal,

C17 charges up through diode CR3 and the Z of the divider. This charge

is relatively faster to simulate some application of brakes without

actually having separate brake control.

Not Game Time (GT) gives override road acceleration via R27 and gate B91:

Page 26

10. Data Accumulator BB5&6

8 bit shift register F5 is used to store the events in the road shaping

program (see #5), The storage is entered serially to forma data stream

for updating the 1024 bit road memory SR E1. The data is organized in

2 bit groups, one group for each speed pulse (maximum of 3 per field).

Each SP gives two advances to S.R. via Fl, 7402, The first advance

enters direction L/R gate E4, BB6. The second enters enable bit. That

is direction is irrelevent unless it is enabled, As many conditional

S.P. pulses as occur enter data into the data accumulator.

Data in Register CC5

Data is transferred broadside from data accumulator (8 above) at ME-

CAR time (MCW gate A4 ). This is after all speed data has been

accumulated in this field, The data IN register is now ready to shift

information into the road memory, (1024 bit S.R.) The shift is in the

opposite direction to that in which it was entered in the data accumulator.

That is, Enable comes out before direction, The last entered data comes

out first. The combination of data accumulator and data IN register

is equivalent to an8-bit shift-left/shift-right register.

When data is needed for entry into road memory (1024 bit S.R.) gate H5

CC5 shifts it out under control of (10) Entry Control,

Memory Entry Control (1024 bit S.R.)

When the road is not moving the contents of memory (1024 S.R.) is

rotating synchronously with line count. There are 256 lines in a

field so the memory rotates 4 bits per line. Two bits per line is all

the information that is used,

Page 27

The time we must update memory is at the top of the picture. The first

entry (for first line) is top of picture memory. Subsequent information

from memory is increment/decrement information. If we want to advance

one line (motion), we must capture the last bits in the memory chain and

replace them with new data. Then to actually do the motion we must

delete one line of memory advance. This procedure places the incremented

data that was for the first line into the second line position and places

new data into the first line position. For the purpose of entry, this

means that the last line must be anticipated for the purpose of changing

it prior to entering the new data, then we delay by deleting advances.

Similarly, if the advance is to be for 2 or 3 lines, the amount of

anticipation must be increased accordingly.

The anticipation circuits are counter Jl, CC7 and 8, which counts the

speed pulses processed in speed pulse sync lock. This counter is set

to 11 in the 4th period following the end of V sync to prepare the

counter to capture the next speed pulses. The count is 11 to 00 to 01

to 10. 10 is the third count. This is decoded in gate Ada, CC7 and

routed to prevent further use of speed pulse by road shaping circuits.

The period that is used for update is 4 lines during V sync and the 4

lines afterward. Since V sync is 4 lines long, this defines the

beginning period. FF P3, 279 CC8 uses V sync and 4V to generate a pulse

that bridges this time (before and after). Only 3 lines before and 3 lines

after are actually used in updating. The last line (after) is used to

reset the S.P. counter for use in the next entry.

Page 28

Bridging functions are generated in exclusive gates below, giving

the following waveforms:

Gate Fay, LZ. PIZZA.

Gate F23 A ZL

When these functions are compared with the content of the counters,

gate F2g and gate Fees the 3 use output forms are: |. Entry Delete |

Advance 1

Advance 2

Advance 3 Left of center is for entry, right of center for count delete, Entry

is decoded at gate E26 for switching entry (pin 3 of memory gate Ei).

Delete count is done from gate Fag which inputs to gate Fg for deleting advance counts.

Page 29

12. Memory (1024 Bit Shift Register, Gate Fl)

A 1M7733 (Intersil) or a 2533V shift register can be used. With the

2533C, -12 volts is required at pin 2.

Data input terminal is pin 5. Recirculation is pins 1 and 7. Most

descriptions are being done in terms of input and output requirements.

Memory Read Circuits - CC 5

Top of the road memory is C5 and B5, AA 3 up/down counters. The road

write counters are C4 and B4, CC 4. At V sync time (top of picture)

the contents of top of road memory are transferred to road write counters.

This is a broadside load. Commencing with line #2, the road write

counters are incremented or decremented with the contents of road memory

(1024 bit S.R.). The road memory is only 2 bits for each line. The

first of these bits is direction. The next is enable. Direction is read

by DFF E4. This FF is connected to gates D4, and D4... If the direction is right, gate ba, is enabled to permit road write counter to be

incremented . Conversely, if left, the decrementing gate is enabled.

The instruction is executed only if the next bit is an enable bit,

otherwise for that line there is no change. The process continues

through all 256 lines in the picture. Thus, the road write counter traces

out the shape of the road. The gated functions are designed so that

"trace out" is the left edge of the road. Comparators B3 and C3 compare

the contents of road write with TV horizontal functions. The output of

these comparators is a very short pulse (2H) which is used to trigger

the road H function counter, M8.

Page 30

13. This pulse is improved by clamping to 5V and using 15V for Vcc source.

Additional delay for 2H functions avoids problems of missing pulses

that can occur because of non-synchronous counters.

Road H Functions EE 2-3

M7 and N7 are the road horizontal counters. It is a 6 bit counter

(3 bits in each of 2 7493s). M8 JK F.F. is count control. The road

write compare triggers the reset input of the control FF and 6 bits are

counted through before the clock input senses the end of count and turns

OFF the H count pulses (gate L8,). The road dimension is a whole 64H function, which is one-fifth of the TV horizontal dimension. The

output of the control FF is the road. To generate a dotted center line

in the road, the rising edge of 64H is sensed by digital mono P3

74279 CC 2, which because of fast reset (1H) generates a narrow line.

This line is chopped by memory shift pulses. The route is gate 81g CC6 to gate D2 CC6 (AFT) to gate P3 and divider N3 CC8. Memory shift

pulses must be used if the chop in the road is to move with the road.

Traffic Motion Functions FF 7-8

The memory shift pulses counted down by one FF K$5 (HH8) are fixed with

respect to the road. That is, if the road moves so does this function

To generate motion for traffic, we want to add to or subtract from this

function for motion up or motion down. The basic memory shift pulses

are divided by 2 (FF K4,, HH&8). That means if we delete one count per

field we create motion up at a rate equivalent to the same motion of

the road created by acceleration. Maximum acceleration is at the rate

of 3 pulses deleted per field. Therefore, the traffic speed created by

Page 31

15. 2 pulse deletions is 2/3 of maximum as desired. Gate 133 ANDS 2V with V sync to generate a pulse of the proper width to capture and

delete one counted down motion pulse. At gate 13, this is ANDED

with divided down shift pulses to do that. Six bit counter K3 and

K4 work from motion processed pulses to form V function for downward

moving (opposing) traffic car shaping. The count pulses for the upward

moving cars need to get one pulse ADDed for proper 2 bit motion. To do

this we use the V sync AND 2V period in the same manner as the delete

function, (via gate 13), and gate 13g), but we chop it with the

horizontal function dots Kayo. Thus, in the delete period we add 2

faster pulses, that is -1+2 = +1, as desired.

Traffic Car Building Circuit EE 7-8

Cars are built from vertical motion function and horizontal road function.

The major vertical functions that define the length of the car are

decoded at gate lag GG7 7420 for upward moving traffic. For the downward

traffic, the same thing is done at gate La, FF7 7420. 32HR and 16HR

are compared in exclusive gate M61, to give the major horizontal limits for botn cars. Traffic downward is ORed with traffic upward at pins

5 and 4 of gate N6 GG6. Downward traffic is gated by FF H6 GG6 and 2F

in order to thin downward traffic. There is traffic in every field

moving upward to ME car, but downward, to make passing feasible,

traffic appears only in every other field. To do this the motion

function for the downward car is divided after its formation (inverter

L5 pin 4). The divide function is up for one field and down for the

next. The switch occurs where the car is so we interrogate every other

field during V sync time with 2F (pin 3 of DFF H6). This enables the

Page 32

16. down car to be present only every other field. That is, it disappears

travelling one whole V dimension in limbo. Cars are ORed in gate Nag.

The up car is assembled in OR gate Nag where wheels and body come together. Similarly OR gate N41, is used for the down traffic.

The difficulty of the game can be increased by a DIP switch at \415 which doubles traffic in the same lane, and/or a DIP switch at H6,. which doubles the traffic in the opposing direction.

ME Steering Circuits EE 3-7

The whole purpose of steering input is to enter a number into direction/

magnitude counter J8 FF6, This direction magnitude counter works the

same as the one in section 5, That is, count below zero or above 15 is

inhibited by use of borrow and carry pulses fed back to either reset or

load at these limits. Between these limits steering input changes the

count in regular steps. Direction is recorded with the most significant

bit. The 3 lesser significant bits are routed through exclusive gates

KB) 4, and 8° Here they are inverted if the most significant bit is present, The resultant output counts upward whether we count down or

Page 33

up (magnitude), If the output bits are zero, the ME car goes straight

without steering correction, If there is a count present the ME car

continues to turn as long as the wheel is not touched, That is it works

just like a real car. The steering inputs are pulses to move the

steering storage count up or down. The optically coded input gives

quadrature pulse to hysterisis gate F93 and FO, (74132). Hysterisis gates must be used here otherwise slow transisions generate multiple

pulses. FF H9 is the direction detection and storage device.

It selects whether we will gate count pulse to count up or down (gates

H749 & H713 ) FF7, FF M7 further counts down the steering pulse to

give somewhat slower response in steering than happens, if we gate the

quadrature pulse of the Atari designed encoder.

ME Car Motion Circuits

The ME car motion circuit defines motion left or right, It is a

synchronous counter with synchronous load capability y7 and K7 .

The count is structured to be identical with the TV horizontal countdown,

except we start to count with lHtofree the last FF in the second 74161 for

the purpose of detecting the beginning of the next count cycle.

Since we are also dividing by 3 in L6 74107 BB2 to detect the beginning

cycle we must AND with begin count here. Gate K6 BB2 does this and

supplies the load signal, The load signal will exist for only one count

pulse since the next output has reset the last (detector) FF. This

detector FF has made it possible for load to enter either counts ahead or

counts behind without lockup. We want to give horizontal motion that is

consistent with the angles of the road as it comes down, The maximum

angle of the road is 45 degrees (almost)

Page 34

When the maximum angle is true the road is incremented or decremented

one 256th of the screen per line (almost). When the road is coming

down at maximum speed the horizontal motion of the ME car must be able

to match this. One 256th unit is equal to one (2 bit) unit in the

horizontal motion counter. The motion by this unit is obtained by:

1 0000 Load Time

0001 Next count - no motion

0000 Next count - motion right oo 08 0010 Next count - motion left

Bits manipulated is seen to be only the least significant two and the

detect bit. If input to gate J7 pin 3 (L,S.) is 1, the signal at 4

(2's significance) is forced to be ZERO. This is the condition for no

motion. If on the other hand the gate J7 pin 3 input is ZERO, then either

0000 or 0010 is loaded depending on the polarity of the direction input

to pin6 of H7 7402 BB4. For the moment ignore exclusive gate K8

BB4 and assume that the direction signal passes through from pin 2

to pin3 with inversion only. We see that the source of the motion pulses

is a programmer of the same kind that is used to form the road. Here

the 74193 gate J&8 (FF6) - direction and rate memory) is similar to

the 74193 gate E7 (direction and slant). This makes possible motion

rates for the ME car that matches any slant in the road. The source of

the pulses that implement ME car motion is the same as the road motion

pulses. Via gate A4 pin 5 to pin 6 (EE7) and pulse programmer

counter N9 , decode SP and pulse routing gates 183 ,L8), & L8,- Thus no matter what rate the road is moving there is a ME car motion

number that will match it.

Page 35

18. It should be noted that actually the road can be incremented only 7 out

of 8 pulses since there are only 7 outputs used in the M9 (EE6) 74145. Using

an additional bit in association with the most significant bit for ME car

motion gives a small added increment of motion that permits that car to

get back on the road against a 45 degree angle. The Motion circuits for

the ME car are incremented at speed pulse time (one line only). The time

from the middle of the picture to end is available for other manipulation

of the motion counter and it is used to bend the car in the direction of

its motion. We want the top to wag in the direction of motion (like a

car) rather than to have the bottom wag opposite to the direction of

motion (like a motor boat), To do this we count rapidly in the direction

of motion before the ME car window, then during the ME car window we count

back. Net motion is ZERO but we have bent (or wagged) the ME car. The

speeded up count is gated into ME car motion at gate 17 FF5 (2V & S.R,)

and into the slant program at gate Ad, EE7 (IV). The direction of the

first half of this count is forward. In the later half we count backward.

Exclusive gate Ko FF4 uses the ME car window to make this switch. Gate

K6 BBS is operational only during V Sync and is used to push the ME car

aside in a crash,

OFF Road and Crash Circuits CC4-5

OFF road coincidence involves feedback to the analog speed control already

discussed in section 7. The coincidence of OFF the road are digital

circuits. The problem of interface is that digital coincidence is a very

short pulse. Too short to use directly as feedback to analog control. We

solve the problem with a digital mono (gate F7 74279 (GG5)). This FF is

set with the short coincidence pulses from gate F6 (GG5) pin 11. The reset

is at a time just prior to the next ME car V window (decoded in gate A615 ).

Page 36

19,

20. This means that coicidence pulses are at least 12 ms long. The same

set and reset pnilosophy is used for collision of ME car with traffic.

Decoded in gate F6, and setting FF F7, 74279. The reason we stretch

this pulse is so that any collision will have a level available during

V sync so that at this time we can gate a limited number of ME car

motion pulses to have the car pushed aside by the collision. V sync

permits 4 motion pulses. The crash pulse is stretched at the collector

of B9, (BB 5) by 10 mfd capacitor C16 to give a reasonable crash time.

Score Counters GG 6-8

Score is simply counting of speed pulses that are actually used to advance

the road. The counting chain is C6 93 ( 1 bit), A8 93 (4 bits), A7 93

(4 bits), N2 90 ( 4 bits), and L2 93 ( 4 bits). The last two 4-bit

counters are decoded to generate score. We-count from 00 to 99

legitimately. If both counters were 7490s, count would wrap around to

ZERO in the event of very high scores, but because we use a 7493 in

the most significant counter and a 7448 to decode it, a different symbol

appears at count 10 instead of wrap around.

Score Functions

74157 gate MZ (HH 6) is a multiplexer (4 pole, 2 position switch

equivalent) for time sharing the 7448 seven segment coder. 9312 multi-

plexer gates the segment to the required TV times, L] handles the

horizontally written segment, and Nl handles the vertically written

segment. Score and road are ORed in gate Kl, 7420 (HH 5). Score and

HME car video are present at pin K913-

Page 37

21.

22.

23. Audio BB 2 & 3

A LM380 is used for audio output. Mixing off OFF road, motor, and

crash sounds occurs at top of the volume control pot.

Motor Sounds BB 2 & 3

Motor sounds are generated from countdown of the non-processed speed

pulses. Counter N9 and C9 give a divide by 4. This is mixed with divide

by 3 the divide by 6 derived from counter C9 (7492). The mixing

resistor mixes approximately equal components of these frequencies.

They are integrated by .1 uf C28. The R24 330 ohm permits a little

high frequency to sneak through giving some sharp picking in the sound.

Crash Sounds BB 3 & 4

To generate the crash sounds the output of Qi is routed 3 ways:

  • Via CR4 and R39 (1.5K) to pull up the charge of C17. This gives it

a proper charge for a slow restart after the crash.

  • Via R40 and CR6. This speeds up the 555 speed pulse generator

to give a screechy crash sound.

  • Via R41, 10K, to operate Q3 and gate Ba, 7406, to remove motor sound integrater C28 from circuit during crash. This changes the

sound to make it very raspy. Q3 also has a connection to set H8

U.F.F. This forces motion to stop during the crash

We improve crash sounds by pulsing the sound integrator on and off

via B9 pin 4. The pulse rate is approximately four per second.

Page 38

24. Crash sounds generated this way tend to have overpowering colume

compared to normal motor sounds. To limit this volume, R18 and

diode CR2 hold volume down during a crash.

Off Road Sounds BB 2

These sounds are gated in D8, 7420. They are enabled only if the

car is moving and OFF the road. Functions 8F and 4V give a beep-beep

effect.

Page 39

TESTING

Game set up requires:

  • Steering assembly using EL740419-3 steering board.
  • Coin switch assembly.
  • Stancore F40-X transformer for 15 volts - optional 16,5 volts

center tap transformer for 5 volts.

4, XM501 Motorola TV chassis or TTL 23C/AC Ball Bros. TV chassis.

PCB is designed to get 5 volts either from Motorola TV chassis or from

an ON board power supply.

A Tektronics 465 oscilloscope or equivalent is a necessary test instrument

for PCB testing.

This circuit explanation was given in the logical sequence for testing.

In other words, at a given point all preceding circuits must be functioning

to allow subsequent tests to be meaningful.

Page 40

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 41
  • CUSTOMER SERVICE INFORMATION

3-1. TEST EQUIPMENT

In order to test any Atari PCB, some items such as the logic probe are absolutely essential. Others are desirable and will make the test procedure easier but are not absolutely essential. Some of these instruments are available from the Atari Customer Service Department and these are: the Kurz-Kasch 520 Logic Probe, the Atari Video Probe and the Hewlett-Packard 10529A Logic Comparator. Other instruments that are very useful are the HP 10526T Logic Pulser and the Tektronix 465 Oscilloscope. These items are available through your local electronics supply house.

3-2. REQUIRED MINIMUM EQUIPMENT

The following items are absolutely essential to perform the test procedures presented in this manual: a. Logic Probe: The logic probe is an instrument designed for checking the outputs of integrated circuits. The Kurz-Kasch Logic Probe, Model No. LP-520, which is available through the Atari Customer Service Department or most large electronics supply houses, is recommended. This logic probe indicates if a signal is a logic high, logic low, or changing from one state to another. Consult the operating instructions included with the probe for further details about its operation. b. Video Probe: The video probe is a very simple but extremely useful device and consists of two test clips, a length of vubber-coated, test-lead wire, and a 4.7K, % watt carbon resistor. Video probes may be obtained from the Atari Customer Service Department or, if necessary, they can be assembled from standard components available at all electronics supply houses.

3-1

Page 42

3-3. OPTIONAL EQUIPMENT

It is possible to find 90% of the possible PCB computer malfunctions without the following items. However, if a complete set of troubleshooting equipment is desired, Atari recommends: a. Hewlett-Packard 10529A Logic Comparator The Hewlett-Packard 10529A Logic Comparator is used to verify correct IC operation. This device simply clips onto in-circuit ICs and instantly displays any logic state difference between the in-circuit test IC and the reference IC in the comparator. logic differences for each pin of a 14 or 16 dual in -line package are indicated by a lamp on the comparator. If the logic comparator is purchased from the Atari Customer Service Department, it is shipped with 20 preprogrammed reference PCBs. If the device is purchased elsewhere, these PCBs must be specially programmed. b. Hewlett-Packard 10526T Logic Pulser The Hewlett-Packard 10526T Logic Pulser is used to stimulate incircuit ICs so that they are driven to their opposite states. This device is available from the Atari Customer Service Department or can be obtained from most large electronics supply houses. C. Tektronix 465 Oscilloscope The Tektronix 465 Oscilloscope is used for viewing various wave forms and should be ordered from Tektronix. Consult the manufacturer's

operating instructions for details on oscilloscope operation.

Page 43

LOGIC TYPE & FUNCTION

TYPE FUNCTION

7400 QUAD 2-INPUT NAND GATE

7402 QUAD 2-INPUT NOR GATE

7404 HEX INVERTER

74SO4 HEX INVERTER

7408 QUAD 2-INPUT AND GATE

7410 TRIPLE 3-INPUT NAND GATE

7413 DUAL NAND SCHMITT TRIGGER

7420 DUAL 4-INPUT NAND GATE

7425 DUAL 4-INPUT NOR WITH STROBE

7427 TRIPLE 3-INPUT NOR GATE

7430 SINGLE 8-INPUT NAND GATE

7448 BCD TO 7-SEGMENT DECODER

7450 DUAL AND/OR GATE (INVERTER/EXPANDER)

7474 DUAL D FLIP FLOP

7483 4-BIT FULL ADDER

7486 QUAD EXCLUSIVE OR GATE

7490 DECADE COUNTER

7492 DIVIDE-BY-12 COUNTER

7493 4-BIT BINARY COUNTER

74107 DUAL JK M/S FLIP FLOP

74153 DUAL 4-BIT MULTIPLEXER

74157 QUAD 2-INPUT DATA SELECTOR/MULTIPLEXER

74165 PARALLEL-LOAD 8-BIT SHIFT REGISTER

74192 SYNCHRONOUS DECADE UP/DOWN COUNTER

3-3

Page 44

74193

4380

NESS5

NES66

RCHL36D

MFC6040

8098

8103

8099

9311

9312

9314

931s

9321

9602

74186 SYNCHRONOUS BINARY UP/DOWN COUNTER

AMPLIFIER

TIMER

FUNCTION GENERATOR

DUAL OPERATIONAL AMPLIFIER

QUAD OPERATIONAL AMPLIFIER

VOLTAGE CONTROLED OPERATIONAL AMPLIFIER

HYBRID

HYBRID

HYBRID

ONE-OF-SIXTEEN DECODER/DEMULTIPLEXER

8-INPUT MULTIPLEXER

QUAD LATCH

4~BIT BINARY COUNTER

DUAL ONE-OF-FOUR DECODER

DUAL MONOSTABLE MULTIVIBRATOR

ROM

3-4

Page 45

vE9E00 SNOILONYLSNI HOLWH3AdO AWMAH

Vv-AaY

#DIR’ NG’

ECT N LOOKING IW ION OF ROTATION

Page 46

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 47

ah Drive Top ASSY P/}.v0320"

PARTS LEST SPECIFICATION Page lof 1 Drawn gan Chen? : ATARI checked 2. Yi2/% [Mechs bow) Lj, | ~". — Innovative Proj. Eng. FEDAN CfkHdy | tec. rng rev. | leisure A | VR. beseription cv Rev. Yeseription | Date pprv. Ty t

i— ——$— — DESCRIPTION item Part Number Qty. ! L 1 oe i , 3 1 4 10 5 10 6 10 shi 4 8 6 Cabinet Assembly Seat Assembly Angle, Connector Bolt, Carriage, i/4 - 20 « lh Le. Washer, Flat, Steel, Reg. Pattern, #% Washer, Lock p Nut, Hex, # %-20 Wingnut, Steel, %-20

Page 48

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 49

SSUMBLY.

PARTS LIST SPECIFICATION Page 1 of 1 ARCADE DRIVER Af | ASSEMBLY TITLE DASHROA P/L qoaiee

Checked YZ, Mech. Eng. \; 2 Eng. Vb _ a Proj, Eng. VEL? yh) VC Elec, Eng REV, [sd C | ove |apprv date __fwprv

ATARI

Innovative ieisure

Part Number DESCRIPTION

] 00313201

2A000598Steering Wheel Assembly, (12" Dia. Wheel)
3003137Panel, Back-up
50005671Bow Washer
&62-008d.Switch, Licon #01-700158 (omit on Highway Game)
70018561Bezel, Start Switch (Omit on Highway Same)
872-1112S6Serew, Mach, Par, Hd., Phil. #10-24 x 3/4 Lg.|
gAQ00E071P.C. Board Assy, Steering
1072-12062Serew, Machine, Phil hd., #2 x 3/8 Lg.
liAUG3470-01Ref. | Main Harness Assy, Highway
Page 50

SEMBEY TILE FOOT PEDAL & BOX ASS'Y P/L 002567

Part) Number DESCRIPTION

ODNRAOULWNHH BRR NHO wb can BRRE IPD A003567 A0O1631 75-15325 75-9158 75-0158 7175-24128 75-914 75-0145 75-054 65-071C

72-6810 002191 A003470-2 4003511 75-9185 75-0188 75-048 PP PRP HR NRF RP NNN YAW FOOT PEDAL & BOX AGSEABLY BOX, ASS'Y SCREW,MACH: PHIL, PAN ha #1/4-20 x 2"le. NUT, HEX 1/4 - 20 WASHER, FLAT, 1/4" SCREW,MACH, RD, HD. PHIL.#4/40 x 3/4 lg. NUT, HEX #4/40 WASHER, FLAT, #1/4" WASHER, LOCK #4 SWLTCH, CHERRY #§51-60B ACTUATOR WIRE PROVIDED WITH SWITCH SHEET METAL SCREW #8x 5/8 lg. BRACKET, SWITCH HARNESS ,FOOT PEDAL SINGLE FOOT PEDAL ASSEMBLY; metal NUT, HEX #8-32 WASHER, FLAT REG. PATTERN #8 WASHER, SPLIT-LOCK, 48 j PARTS LEST SPECIE TCAT ION Page |of 1 | Drawn H,WOLFF |

ATARICheckedMech. En.|

Tr —

Innovativero}. (08. AWOLEFLice, EneREV,
leisureIrA J

Rev. | Bescription I late Description | Date HEPES

Page 51

ARCADE DRIVER

asASSEMBLYi P ELECTRONIC TRAY ASSEMBLY

PARTS LIST SPECTEICATION Page |_of 1

[orawnRegan Cheng|
ATAR|Checked 7.Mech. Lng. ZH”
InnovativeVeq[ Elec. Pne| REV,
leisure|| ‘
Revebeseriptionbeseription

=

TremPart Numberary. |DESCRIPTION
10033391 | Electronics Tray|
2qg006221 | Cover, Transformer
j 3000871L Label
4GO1S5i1 | Transformer
a)79-32012 | Fuse Holder
' 646-201101 | Fuse, 1 Amp, Slo Blo
| 790-30011 | Filter, Power Line
854-4011 Power Cord, 8!7
972-661013 | Screw, S.M., Pan Hd., Phil., #6 x 5/8" Lg
10A0019201 | Harness, Voltage Selector
| aa#A001921-01A/R| Shorting Block, 35V
L£U01921-02A/R! Shorting Block, 110V
| 43A001921-03A/R}| Shorting Block, 220V High
14* AQO1921-04A/R| Shorting Block, 220V Low

*Install Shorting Blopk per voltage requirements.

Page 52

T ASSEMBLY TITLE Zp C, BOARD ASSEMBLY - BYWAY P/L 003211 I|\ PARTS LIST SPECIFICATICN Page | of 2 Drawn ATARI Checked 72. Y2e/ Pr | Mech. Ing.

Innovative | Proj, Eng.Elec, EnglREV. |
leisureeae)Zz

ire“) = J

Rev.Descriptiona

Item fart Number Qty DESCRIPTION 1 37-7400 13 |Integrated Circuit, 7400 | 2 37-7402 4 " " 7402 3 37-7404 11 ® " 7404 4 37-7405 3 " a 7405 5 37-7406 1 x 4 7406 6 37-7408 1 " u 7408 7 37-7410 7 " 7410 8 37-7420 8 " " 7420 g 37-7427 2 7 " 7427 10 37-7430 1 " " 7439 ll 37-7448 1 " a 7448 12 37-7474 5 " me 7474 13 37-7486 7 " " 7486 14 37-7490 1 a 7 7490 15 37-7492 1 * " 7492 16 37-7492 17 x ” 7493 17 37-74107 4 ¥ 7 74167 18 37-74132 1 7 " 74132 19 37-74145 2 ” " TH14S 20 37-9322 1 n " 9322 21 37-9316 2 " * 9316 22 37-74164 1 " " 74164 23 37-74165 1 " " 74165 24 37-74193 6 " % 74193 25 37-74279 2 = " 74279 26 37-9312 2 " 7 3322 27 37-2533V 1 # " 2533V 28 37-555 2 “ " 555 29 37-LM380 1 " LM380 30 37-LM340T-15 1 ‘ " LM340T-15 31 10-5270 1 |Resistor, Carbon, % Watt, 5%, 27 ohm 32 10-5100 1 " " " "10 ohm 33 10-5181 1 " " "180 onm 34 10-5501 l " " a m 5¢O0 onm 35 10-5331 5 ? - 3 Watt " 230 ohm 36 11-5391 1 " " % Watt " 390 ohm 37 10-5471 6 7 u % Watt " 470 ohm 38 10-5183 \ # m " " {SK ohm 39 10-£%¢3 1 " " " "2K ohm 40 10-5102 1 ik ” " "1K ohm

Page 53

ASSEMBLY TITLE P.C. BOARD ASSEMBLY - HYWAY P/L. 003211 Rey B PARTS LIST SPECIFICATION Page 2 of 2 '

[tem Part NumberQty.DESCRIPTION

41 10-5152 z@ Resistor, Carbon, % Watt, 5%, 1.5K ohm

4210-52222"uu” 2.2K ohm
4310-527221:7=2.7K ohm
4y10-53321"""" 3.3K onm
oeL ate1"""" Wwf Onn
Ko10-51037i""" 10K ohm
47 . 10-53332""™33K ohm
48 10-54735""" 47K ohm
ca) 10-51042""== 100K ohm
50 10-55641m"o $60K ohm
5110-51251"""" 1.2M ohm

5? 19-311104 1 Trimpot, 100K, CTS #X201R104B 53 19-311105 1 Trimpot, 1M, CTS #X201R105B 54 28-101101 1 Capacitor, Dipped Mica, 100pf 55 28-101271 1 Capacitor, Dipped Mica, 270pf 56 27-101102 2 Capacitor, Ceramic Disc, .00luf $7 27-101103 3 Capacitor, Ceramic Disc, .Oluf, +80%, -20% 58 27-101104 16 Capacitor, Ceramic Disc, .luf, +80%, -20% 59 24-100105 2 Capacitor, Electrolytic, luf, 10V 60 24-100106 4 || Capacitor, Electrolytic, l0uf, 10V 61 24-250107 1 Capacitor, Electrolytic, 100uf, 25V 62 24-250227 1 Capacitor, Electrolytic, 22Cuf, 25V 63 24-060257 1 Capacitor, Electrolytic, 250uf, 6¥V

6424-1605071|| Capacitor, Electrolytic, s00uf, 16V

65 24-250478 1 Capacitor, Electrolytic, 47CCGuf, 25V 66 21-101104 1 Capacitor, Mylar, O.luf, 10%

6731-1N91411 Diode, 1N914
6831-1N40013 Diode, 1N4001
6932-1N47421 Diode, Zener, 1N4742Z
7034-2N36433 Transistor, NPN, 2N3643
7133-2N36443 Transistor, PNP, 2N2644

TD 002743 1 Crystal, 12.096 Mhz 73 66-08 a Dip Switch, Molex 4130, #01-70-0106 74 003212 1 Printed Circuit Board

Page 54

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 55

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.