Midways Card Rack System Part 1
Wizard of Wor (Dave Nutting Associates / Midway, 1980) · Manual · 53 pages · 34 sections · original scan
° MIDWAY’S
CARD RACK SYSTEM
PART I
#926-MINI
#927-COCKTAIL #873-UPRIGHT
bad MIDWAY MFG. CO. ABALLY COMPANY 10750 WEST GRAND AVENUE 7 FRANKLIN PARK, ILLINOIS 60131 U.S.A. PHONE: (312) 452-5200 FORM-00237-8012 PHONE:
TOLL FREE
800-323-7182
TABLE OF CONTENTS
Page No. COMMERCIAL CARD RACK ASSEMBLY & PARTS 1 SWITCH ADJUSTMENT — WIZARD OF WOR 2 SWITCH ADJUSTMENT — GORF 3 RAM — ROM TEST — SPACE ZAP 4—5 TEST DISPLAY — GORF 6 RAM & PATTERN TEST CARDS 7—8 PATTERN BOARD TEST 9—10 PATTERN BOARD THEORY OF OPERATION 11-12 PATTERN BOARD TEST SCHEMATIC 13—13A TROUBLE SHOOTING CARD RACK SYSTEM 14-15 CUSTOM CHIP PIN OUT 16 1/0 CHIP DESCRIPTION 17 ADDRESS CHIP DESCRIPTION 18 DATA CHIP DESCRIPTION 19 1.C. FUNCTION CHART 20—21 Z80 CPU PIN DESCRIPTION 22 STRAPPING CHARTS 23—24 LOGIC TERMS Z80 25—26 R GB BOARD SCHEMATIC 27 AUDIO AMP. BOARD SCHEMATIC & CONTROL GRIP 28—28A WIRING SCHEMATIC — SPACE ZAP 29 WIRING SCHEMATIC — GORF 30 POWER SUPPLY SCHEMATIC 31 GAME BOARD LAYOUT — SPACE ZAP 32 GAME BOARD SCHEMATIC — SPACE ZAP 33 GAME BOARD LAYOUT — GORF 34 GAME BOARD SCHEMATIC — GORF 35 CPU BOARD LAYOUT 36 CPU BOARD SCHEMATIC 37 PATTERN BOARD LAYOUT 38 PATTERN BOARD SCHEMATIC 39 RAM — ROM BOARD LAYOUT (FOREIGN & DOMESTIC) 40—41 RAM — ROM BOARD SCHEMATIC (FOREIGN & DOMESTIC) 42—43 RAM BOARD LAYOUT 44 RAM BOARD SCHEMATIC 45 SERVICE BULLETINS 46—49
COPYRIGHT 1980 ©BYMIDWAYMFG.CO. —_ALL RIGHTS RESERVED.
NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM. OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER.
FOR PERMISSION REQUESTS, WRITE: MIOWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131
COMMERCIAL CARD RACK ASSY.
A789-00003-0000 A789-00004-0000 A789-00005-0000 0789-00100-0000 0789-00106-0000 0017-00101-0099 0017-00104-0019 A082-90006-B000 A082-91356-C000 A082-91354-F000 A082-91355-C000 A084-91364-A873 A084-90708-C873 0017-00007-0153 P.C. RACK ASSY. - RIGHT P.C. RACK ASSY. - LEFT P.C. RACK ASSY. - BASE MTG. BRKT. SUPPORT (2 REQ’D.) RACK STRAP (2 REQ’D.) #6 x 1/4 SLT. HEX HD. SCREW (11 REQ’D.) #6 FLAT WASHER (3 REQ’D.) BACK PANEL P.C. ASSY. (MOTHER BOARD) RAM BOARD ASSY. CPU BOARD ASSY. PATTERN TRANSFER BOARD ASSY. PROGRAMMED ROM/RAM BOARD ASSY. GAME LOGIC BOARD ASSY. P.C. BOARD SUPPORT (2 REQ’D.) (NOT SHOWN)
SWITCH ADJUSTMENT - WIZARD OF WOR
OPTION SWITCH SETTINGS
Option switches are located on the game P.C.B. in the commercial card rack
COINS PER CREDIT
LEFT HAND COIN SLOT IS CONTROLLED BY SW. #1 SW. #1
| OFF | 1 COIN | 1 CREDIT |
| ON | 2 COINS | 1. CREDIT |
RIGHT HAND COIN SLOT IS CONTROLLED BY SW. #2 AND SW. #3 sw. #3 SW. #2
| OFF | OFF | 1 COIN | 1 CREDIT |
| OFF | ON | 2 COINS | 1 CREDIT |
| ON | OFF | 1 COIN | 3 CREDITS |
| ON | ON | 1 COIN | 5 CREDITS |
LANGUAGE
sw. #4 OFE ENGLISH ON FOREIGN LANGUAGE (REQUIRES A082-91374-A000)
WORRIORS PER CREDIT
SW. #5 OFF 1 CREDIT = 2WORRIORS / 2 CREDITS = 5 WORRIORS ON 1 CREDIT = 3 WORRIORS / 2 CREDITS = 7 WORRIORS
BONUS PLAYER AWARDED:
sw. #5 OFF BONUS WORRIOR AFTER 3RD DUNGEON ON BONUS WORRIOR AFTER 4TH DUNGEON
PLAY MODE
SW. #7 OFF COIN PLAY ON FREE PLAY
GAME ATTRACTION SOUNDS
SW. #8
| OFF | CONTINUOUS | SOUND | DURING | “ATTRACT | MODE” |
ON SOUND DURING ATTRACT MODE ONLY IF GAME CONTROLS ARE TOUCHED. (WHEN ANY BUTTON OR CONTROL IS TOUCHED, GAME PROVIDES SOUND FOR ONE COMPLETE CYCLE ON THE ‘ATTRACT MODE”’. IT WILL THEN BE QUIET UNTIL TOUCHED AGAIN).
PART NO. M051-00961-A021
SWITCH ADJUSTMENT — GORF
ADJUSTMENT SWITCHES
LEFT HAND COIN SLOT IS CONTROLLED BY SW. #1
SWITCH #1
| OFF | 1 COIN | 1 PLAY |
| ON | 2 COINS | 1 PLAY |
RIGHT HAND COIN SLOT IS CONTROLLED BY SW. #2 & #3
SWITCH #2 SWITCH #3
| OFF | OFF | 1 COIN | 1 PLAY |
| ON | OFF | 2 COINS | 1 PLAY |
| OFF | ON | 1 COIN | 3 PLAYS |
| ON | ON | 1 COIN | 5 PLAYS |
SWITCH #4 ENGLISH ON OTHER LANGUAGE REQUIRES A082-91374-A000.
NUMBER OF BASES PER GAME
SWITCH #5 OFF TWO BASES PER CREDIT ON THREE BASES PER CREDIT
SWITCH #6 BONUS BASE AWARDED AFTER MISSION #5 ON NO BONUS BASE
SWITCH #7 OFF COIN PLAY ON FREE PLAY
SWITCH #8 OFF GAME ATTRACTION SOUNDS DURING GAME OVER ON NO GAME ATTRACTION SOUNDS DURING GAME OVER
M051-00873-A14.
RAM-ROM TEST - SPACE ZAP
PLACING THE TEST SWITCH, (LOCATED ON THE AUDIO AMPLIFIER ASSEMBLY IN THE COIN BOX AREA) TO ON PERFORMS THE FOLLOWING FUNCTIONS:
- REMOVES ALL ACCUMULATED CREDITS
- TESTS THE SCREEN RAM
- TESTS THE STATIC RAM
- TESTS THE GAME ROM/EPROM
- REPEATS ALL TESTS INDEFINITELY
PLACING THE TEST SWITCH IN THE OFF POSITION RETURNS THE GAME TO NORMAL OPERATION AFTER COMPLETION OF THE ROM TEST. IF YOU WERE TO TURN THE TEST SWITCH OFF DURING THE SCREEN RAM TEST, IT WOULD TAKE APPROXIMATELY 15 SECONDS BEFORE THE GAME WOULD RE-APPEAR.
THE GAME DOES A MODIFIED FORM OF RAM TEST UPON POWER-UP OR WHENEVER THE DOOR-SLAM SWITCH IS ACTIVATED. IF AN ERROR IS FOUND, THE PROGRAM CONTINUES THE TEST UNTIL THE ERROR IS CLEARED. THEREFORE, IT IS POSSIBLE THAT THE GAME WILL NEVER START AND/OR THERE MAY BE NO INDICATION OF ANYTHING ON THE SCREEN IF THERE IS A RAM ERROR.
ERROR INDICATIONS
IF ALL RAM AND ROM ARE GOOD, THE ONLY INDICATION WILL BE AN OCCASIONAL FLASH ON THE SCREEN (APPROXIMATELY EVERY 16 SECONDS). THIS INDICATES THAT IT HAS PASSED ALL TESTS AND IS STARTING THE TEST SEQUENCE OVER AGAIN.
IF AN ERROR IS FOUND IN THE SCREEN RAM, YOU WILL SEE THE FLASH ON THE SCREEN FOLLOWED BY FLASHING RANDOM HORIZONTAL BARS. IT WILL THEN CYCLE THROUGH THE TEST AGAIN UNTIL THE ERROR IS CLEARED.
IF AN ERROR IS FOUND IN THE STATIC RAM, THERE WILL BE SHORT BURSTS OF FLASHING HORIZONTAL BARS DISPLAYED ON THE SCREEN. IT WILL THEN CYCLE THROUGH THE SCREEN RAM TEST AND THE STATIC RAM TEST AGAIN UNTIL THE ERROR IS CLEARED. THE CYCLE TIME IS APPROXIMATELY 3 SECONDS.
RAM-ROM TEST - SPACE ZAP
ABAD ROM/EPROM IS INDICATED BY A NUMBER 1, 2, 3, 4, 5, 6, 7, OR 8 DISPLAYED ON THE SCREEN. IF MORE THAN ONE ROM/EPROM IS BAD BOTH NUMBERS WILL APPEAR ON THE SCREEN.
IF YOU HAVE 8 2K ROMS/EPROMS
NUMBER DISPLAYED BAD ROM/EPROM IN SOCKET x1 X2 X3 x4 X5 x6 x7 X8 MONOD ARWND =
IF YOU HAVE 4 4K ROMS/EPROMS
NUMBER DISPLAYED BAD ROM/EPROM IN SOCKET x1 x1 X3 X3 X5 x5 X7 x7 ONOOhWN +
TEST DISPLAY FOR GORF
| COIN | COIN | DISPLAY CAN | ||||||
| JU2 | Jut | PLAY | PLAY | SLAM | TEST | sw. | sw. | BE SEEN |
| ER | TT | #2 | a" |
m SSN
rTP ar 4 SW. OFF OR
JUMPED NOT
| NoT | NOT | NOT | TRIG | RIGHT | LEFT | DOWN | up |
| USED | USED | USED | GER | INSTALLED | |||
| * | * | . | * | * |
Lb 49 Lb JL A DISPLAY CANNOT BE SEEN
ro
| TRIG | RIGHT | LEFT | DOWN | UP |
GER L SW. ON OR JUMPER INSTALLED
- ACTIVATED BY 2ND SET OF PLAYER CONTROLS
| SET | SET | SET | SET | SET | SET | SET | SET | " |
| sw. | sw. | sw. | sw. | sw. | . | sw. | sw. | USED IN COCKTAIL |
| 8 | 7 | 6 | 5 | 4 | 2 | 1 | CABINET ONLY |
ABCDEFGH ® eos
A LETTER APPEARING HERE INDICATES A BAD ROM/E PROM
Placing the test switch (located on the Audio amplifier assy. in the coin box area) to ‘‘on”’ performs the following functions:
- Removes all accumulated credits.
- Test the screen rams.
- Test the static rams.
- Test all switches,
If a screen ram is defective random bars will flash on screen. If a static ram is defective a random dotted pattern will flash on screen. Dotted pattern will flash on the screen. If all rams are good the switch test pattern will appear on the screen. All switches must be ‘‘off’’ to get the pattern shown above. When each switch is turned on the position of that switch will disappear. Time delay between returning test switch to ‘‘off'’ and game over sequence is normal approx. 25 seconds.
10.
11.
12.
13.
14.
15.
16.
17.
18.
MIDWAY
VIDEO IS OUR GAME
CARD RACK BOARD TEST
RAM TEST
. Remove Game Card PC A084-90708-A902 & Rom Ram Card A082-91364-A000.
. Remove Pattern Card PC A084-91355-C000.
. Remove Ram Card in position J-2 PC A082-91356-B000.
. The Ram Card in position J-1 must remain and be a known good card.
. Do not remove the CPU Card A082-91354-E000.
. Insert the Card Rack Board Tester PC A080-91517-A000 into position J-4.
. Insert the Ram Test Card into position J-6 PC A080-91516-A000.
. Insert the bad Ram Card into 18 pin connector of Ram Card Tester.
. Connect video cable to connector J-2 of Card Rack Board Tester pins 11 and 12.
Move black slide switch on Card Rack Board Tester into position #1.
The dip switch settings must be as follows: 1- 3-5-7 OFF and2-4-6-80ON.
Press Red reset button (S-1) on Ram Test Card to clear system.
A bad Ram location will flash on video screen and on flashing Rams indicate all Rams are good.
Move black slide switch on Card Rack Board Tester to position #2.
Clear system again by pressing Red reset button on Ram Test Card $1.
If the Rainbow test shows Garbage, check the video output. (74LS166)
When Rams are all good and Rainbow pattern is clear this indicates a good Ram Card.
Proceed to Pattern Card Test.
PATTERN BOARD TEST
- Remove Ram Test Card PC A080-91516-A000.
- Remove Card Rack Board Tester Card from J-4 and insert it into J-6 A080-91517-A000.
- Remove the two Ram Test Proms located at X-4 and X-5 of Card Rack Board Tester.
- Insert two Pattern Test Proms at location X-4 and X-5.
- Connect video cable to connector J-2 of Card Rack Board Tester pins 11 and 12.
- Insert bad Pattern Card into 50 pin connector of Card Rack Board Tester.
- Press Red reset button to clear system.
- A bad Pattern Card will display area of trouble on video screen.
- A good Pattern Card will display the words (‘‘LOOKS GOOD’’).
- Connectors J-1 and J-5 are not used at this time.
- The Dip Switch is for future use.
MIDWAY’S CARD RACK SYSTEM
PATTERN BOARD TEST
FATAL ERRORS LOCATION
DATA LATCHES U19 & U10
74LS175
FLUSH DATA BIT 08 U21 PIN 10 74174
DIRECTION DATA BIT 01 U21 PIN 2 74174
AREA AND LINEAR HIGH 2 BITS LINEAR: U7 PIN3 & 13 U8 PIN 10 & 13
AREA: U9PIN3 &13 U8 PIN 11 &14
TRI - STATE BUFFERS U20 & U11 74LS367
CONTROL LOGIC (CLOCK) US - 74LS161 U6 - 74LS04 U12-74LS00
- U21 74LS174 1S THE STATUS LATCH.
PIN 2DIRECTION
PIN 5EXPAND
PIN 7 CONSTANT
PIN 10 FLUSH
PIN 12FLIP
PIN 15 FLOP
THE U21 STATUS CHIP WILL CONTROL THE SHIFTING OF DATA IN A CERTAIN DIRECTION, MAKING A LARGER OBJECT, MOVING THE SAME SIZE OBJECT, TURNING OR ROTATING THE OBJECT, ETC.
- THE HEX. CODE 08 AND 01 IS CONVERTED INTO A BINARY CODE:
08 = 00001000
01 = 00000001
- FLUSH SETS MEMORY TO A FIX COLOR.
ERRORS
- DATA BUS
- LINEAR
- AREALD
- XWIDE
- FEED BK
- STATUS
- LINEAR CT
- AREACT
ERRORS
FLOP
FLIP
FLUSH
CONSTANT
EXPAND
DIRECTION MIDWAY’S CARD RACK SYSTEM
PATTERN BOARD TEST
STATUS (U21) LOCATION
U10 & U19
U7, U16, U25 & U34
U27, U30, U36 & U39
U31, U32, U33, U40, U41 & U42
U28, U29, U37 & U38
U21
U7, U8, U16, U17, U25, U26, U33 & U34
U9, U15, U17, U18, U23 & U24
LOCATION
PIN 15
PIN 12
PIN 10
PIN 7
PIN 5
PIN 2
PATTERN BOARD THEORY OF OPERATION
MIDWAY’S CARD RACK SYSTEM This explanation of the theory of operation is intended to be very basic and not a chip-by-chip or signal-by-signal explanation. There are some complicated features of this assembly that would take too much room to explain nor would it serve any useful purpose for the service technician.
The function of this board is to move blocks of data from one memory location to another at a fast rate. In the Card Rack System this translates into the ability to transfer a pattern on the screen (or from ROM) to another location on the screen.
Parameters are passed to the Pattern Board by a series of output instructions to ports 78 through 7E. IC’s U1, U2, U4 and portions of U3, U6 and U14 perform the port decoding.
The follwing is a sequence of events in a typical operation of transferring a color encoded pattern from ROM to screen RAM.
The mode control byte is loaded into U21 by an output instruction to port 7A. Here the various modes of operation are selected.
The sixteen-bit linear address (which is usually the source address) is loaded into U34, U25, U16 and U7. The low-order eight bits are loaded into U34 and U25 by an output instruction to port 78. The high-order eight bits are loaded into U16 and U7 by an output instruction to port 79.
The sixteen-bit area address (which is usually the destination) is loaded into U39, U30, U18 and U9. The low-order eight bits are loaded into U39 and U30 with an output instruction to port 7B. The high-order eight bits are loaded into U18 and U9 with an output instruction to port 7C.
A line offset value is loaded into U39 and U30 with an output instruction to port 7B.
The width of the pattern is loaded into U41 and U32 with an output instruction to port 7D. The height of the pattern is loaded into U40 and U31 with an output to port 7E. This instruction also starts the following sequence to perform the actual pattern transfer.
The output to port 7E persets one-half of U13 sending the signal BUSREQ low. The Z-80 (located on the CPU board) responds by tri-stating its address, data and control signals and then asserting BUSACK low.
ab
PATTERN BOARD THEORY OF OPERATION Page 2
When BUSACK goes low, the control signal buffers for RD, WR, MREQ and IORQ are enabled placing the control signals on the bus; the tri-state address multiplexers U35, U26, U17, U8 and data buffers U20 and U11 are enabled placing their signals on the bus; and the master clock generator U5 starts counting. During the time that this Pattern Board has control of the bus, the signal appear identical to those created by the Z-80.
The first cycle is a read from the address contained by the linear address counters with the data going into the data hold registers U19 and U10.
The next cycle is a write cycle to the address contained in the area address counters. The data is placed on the data bus by the tri-state buffers U20 and U11.
This typical read-write cycle continues until the width counters U42 and U33 count down to zero. This completes one horizontal line of data transfer.
To prepare for the next horizontal line of data transfer two things must occur. First, the width count contained in U41 and U32 is loaded into U42 and U33. Simultaneously the height count contained in U40 and U33 is decremented. Second, the distance to the starting point on the next line, contained in U39 and U30 is added (through U38 and U29) to the present count contained in U37 and U28 and then loaded into counters U36 and U27.
These line transfers count until the height counters U40 and U31 reach zero.
At this time, BUSREQ is taken high disabling the clock generator U5 from any further activity. Also all data, address and control lines are tri-stated off of the bus returning control to the Z-80. The Z-80 responds by taking BUSACK high and continuing with its normal operation.
PATTERN BOARD SCHEMATIC
FLUSH DATA BIT 08°
DIRECTION DATA BIT 01
LINER CONTROL
We =| U26
AREA CONTROL
us a] U9 [og
DATA LATCHES STATE BUFFERS | TRI
_ LINEAR —_—_—— on Y TINEAR jo e ee
LINEAR COUNTER
a i a sf 02° pa iT
REFPE TTT +S SS
AREA COUNTER
13A PATTERN BOARD TEST
TROUBLE SHOOTING CARD RACK SYSTEM
All test points are found on the rear side of the Back Panel Board PC A082-93006-C/ D000.
- +5VDC PINS 87 AND 88.
- +12VDC PINS 91 AND 92.
- -5VDC PINS 95 AND 96.
4, LOGIC GROUND PINS 99 AND 100.
- SYSTEM CLOCK 7.1MHZ PINS 97 AND 98.
- VIDEO CLOCL 3.5MHZ PINS 93 (CHROM).
- CPU CLOCK 1.7MHZ PINS 89 AND 90.
- CPU RESET PIN 94 (NORMALLY HIGH).
- DATA BITS (0-7) PINS 44 TO 51.
- ADDRESS BITS (0-15) PINS 55 TO 70.
- COMPOSITE VIDEO PIN 85.
For all Additional Test Points refer to Page #15.
PIN
SIGNATION
sit WE SER1
SERO
RASS RAS2 RASi
RASO
CAS
DATEN
MAO MAS 25
WATCHDOG
LIGHTPEN
MXD1 MXD2 MXD3 MXD4 MXDS MXD6 MXD7 po D1 D2 D3 D4 DS D6 BACK PANEL BOARD PC A082-93006 C/D000 DESCRIPTION PIN DESIGNATION Screen RAM Video Load Strobe 51 DT Write Enable 52 SCREEN Serial Data 1 53 RMCO Serial Data 0 54 RMCL Row Address Strobe 3 55 AO Row Address Strobe 2 56 Al Row Address Strobe 1 57 A2 Row Address Strobe 0 58 AB Column Address Strobe 59 Aa Data Write Enable 60 AS Multiplexed Address Bit 61 AG Maitiplexed Address Bit 62 AT Multiplexed Address Bit 63 AB Maltiplexed Address Bit 64 Ag Multiplexed Address Bit 65 A10 Multiplexed Address Bit 66 All Memory Data Bus Bit 67 A12 Memory Data Bus Bit 68 A13 Memory Data Bus Bit 69 Al4 Memory Data Bus Bit 10 AIS. Memory Data Bus Bit 11 RFSH Memory Data Bus Bit 12 WAIT Memory Data Bus Bit 13 BUSACE Memory Data Bus Bit 14 wR Buffered Address Bit 0 15 BU Buffered Address Bit 1 16 MI Microcycle Data Bus Disable 7 TORQ Automatic Reset 18 WREQ Lightpen Interrupt 79 HALT Vertical Sync 80 INT Horizontal Sync 81 +5¥ Microcycle Control 0 82 +S¥ Microcyele Control 1 83 R-Y Read 84 B-Y Machine Opcode Cycle 85 VIDEO Microcycle Data Bus Bit 86 +25 vREF Microcycle Data Bus Bit 87 +5¥ Microcycle Data Bus Bit 88 +5v Microcycle Data Bus Bit 89 ® Microcycle Data Bus Bit 90 ® Microcycle Data Bus Bit 91 +12v Microcycle Data Bus Bit 92 +12v Microcycle Data Bus Bit 93 CHROMA Data Bit 94 RESET Data Bit 95 -5v Data Bit 96 -5v Data Bit 97 ™ Data Bit 98 T™ Data Bit 99 GND Data Bit 100 GND
onaaen nenemade Onamenon
onamene DESCRIPTION Data Bit 7 Soreen RAM Decode Refresh Microcycle Control 0 Refresh Microcycle Control 1 Address Bit 0 Address Bit 1 Address Bit 2 Address Bit 3 Address Bit 4 Address Bit 5 Address Bit 6 Address Bit 7 Address Bit 8 Address Bit 9 Address Bit 10 Address Bit 11 Address Bit 12 Address Bit 13 Address Bit 14 Address Bit 15 Dynamic RAM Refresh
Wait Bus Acknowledge Write Bus Request Non-maskable Interrupt Input/Output Request Memory Request Halt CPU stopped Interrupt Request Positive 5 volt Power Supply Positive 5 volt Power Supply Red minus Video Blue minus Video Composite Video 2.5 volt Chrome Center Reference Positive 5 volt Power Supply Positive 5 volt Power Supply CPU Clock 1.7897725 Mhz Opposite phase CPU Clock 1.7897725 Mhz Positive 12 volt Power Supply Positive 12 volt Power Supply 3.579545 Mhz Chroma Subcarrier
Reset Negative 5 volt Power Supply Negative 5 volt Power Supply System Clock 7.15909 Mhz Opposite phase system clock 7.15909 Mhz Systom Power and Logic Ground System Power and Logic Ground
CUSTOM DATA
Qa G [e) = b> oO ~) PY) Mm n 2) VERTOR
HORZDR
Als
RFSH
Al2 AI3 CUSTOM 1/0
1/0 CHIP DESCRIPTION
The Z-80 communicates with the |/O Chip through Input and Output instructions. The state of an 8 x 8 switch matrix can be read through the Switch Scan circuit. When an Input instruction is executed, one of the SO0-SO7 lines will be activated. When a line is activated, the switch matrix will feed back eight bits of data on SI0-SI7. This data is in turn fed to the 2-80 through MUXDO - MUXD7.
The Z-80 can read the position of four potentiometers (pots) through the A-D Converter circuit. The pots are continuously scanned by the A-D Converter and the results of the conversion are stored in a RAM with Input instructions.
The Z-80 loads data into the Music Processor with Output instructions. This data determines the characteristics of the audio that is generated.
ADDRESS CHIP DESCRIPTION
THE Microcycle Decoder generates twelve bits of Z-80 address from the 8-bit Microcycle Data Bus. This address is then fed through MUX I and MUX II to MAO-5 which go to the RAM. The Scan Address Generator generates a 12-bit address which is used to read video data from the RAM. This address goes from 0 to FFFH once every frame (1/60 sec.).
MUX | sends either the Scan Address of Z-80 Address to its 12 outputs. An output of the Scan Address Generator controls MUX |. If the Scan Address Generator and the Z-80 request a memory cycle at the same time, the Scan Address Gererator will have higher priority and the Z-80 will be required to wait (by the WAIT output). The Scan Address Generator never requires the memory for more than one consecutive memory cycle, so the Z-80 is never required to wait for the memory for more than one cycle. HORIZ DR and VERT DR synchronize the Scan Address Generator with the Data Chip and the TV Scan.
The purpose of MUX II is to multiplex its 12 inputs to the six address bits in the two time slices required for 4K x 116 pin RAMS.
The Memory Cycle Generator controls memory cycles generated by either the Z-80 or Scan Address Generator. MREQ, RD, Mi, RFSH, and A12-A15 are from the Z-80. A12-A15 are fed directly from the Z-80 because if they were brought out of the Microcycle Decoder, they would arrive too late in the memory cycle. The RASO - RAS3 outputs are used to activate memory cycle and all four RAS’s are used to control four banks of RAM (16K x 8). WRCTL and LTCHD0 are control signals to the Data Chip. WRCTL tells the Data Chip when to place data to be written to memory on the Memory Data Bus. LTCHDO tells the Data Chip when valid data from RAM is present on the Memory Data Bus.
DATA CHIP DESCRIPTION
The TV Sync Generator uses 7M and 7M (7.159090 MHZ square waves) to generate NTSC standard sync and blank to be sent to the Video Generator. It also generates HORIZ DR and VERT DR for synchronization with the Address Chip. HORIZ DR occurs once every horizontal line (63.5 usec), and VERT DR occurs once every frame (16.6 msec).
The Shift Register loads parallel data from the memory data bus (MDO - MD7) and shifts it out of its two serial outputs. The TV Sync Generator controls when data is loaded or shifted. In acommercial game SERIAL 0 and SERIAL 1 are sent through the MUX | to MUX II. The two bits from MUX | select 8 bits to be sent through MUX II to the Video Generator. These 8 bits then determine the analog values of VIDEO, R-Y, and B-Y. 2.5V is a 2.5V DC reference level.
The Clock Generator generates 0G and PX from 7M. These are the clocks for the rest of the system. The frequency of PX is half that of 7M and the frequency of 0G is half that of PX.
The Microcycle Generator generates the microcycle control bits, MCO and MC1, from TORQ, MREQ, RD, and M1, all from the Z-80.
In memory write cycles WRCTL is activated and the Memory Control circuit generates DATEN. The Magic Function Generator takes the data from the Z-80 on MUXD0 - D7 and transfers it to MDO - MD7. If a Magic write is being done, the Magic Function Generator will modify the data as required before it places it on the memory data bus.
SPACE ZAP GAME BOARD (PC A084-90708-A902) CHIP NUMBER 74LS02 74LS08 74LS32 74LS74 74LS133 74LS138 74LS139 MC14078 MC14174 2114 2716-8516 9316 2720- (0066-117) Additional Devices: TIP110 2N4401 2N4403 1N4004 CARD RACK LOGIC BOARDS
FUNCTION Quad 2 input Nor Quad 2 input And Quad 2 input Or Dual ‘‘D’’ Flip-Flop 13 input Nand 3 to 8 line decoder Dual 2 to 4 line decoder 8 input Nor Hex ‘‘D’’ Flip-Flop RAM PROM 16K ROM 16K | & O custom chip
NPN transistor NPN transistor PNP transistor Diode
CPU BOARD (PC A082-91354-D000) CHIP NUMBER 74LS00 74LS02 74LS04 74LS08 74LS10 74LS20 74LS74 74LS157 74LS174 74LS175 ‘Z80 2719- (0066-115) 2721-(0066-116) 74LS245 74LS257 74874 7416 MC14024 Additional Devices: 2N4401 T18-137 1N4004 1N4148 14.31818
1S) NS onnond FUNCTION Quad 2 input Nand Quad 2 input Nor Hex inverter Quad 2 input And Triple 3 input Nand Dual 4 input Nand Dual ‘‘D’’ Flip-Flop Quad 2 input multiplexer Hex ‘‘D’’ Flip-Flop Quad ‘‘D’’ Flip-Flop CPU Address custom chip Data custom chip Octal bus transceiver Quad 2 input multiplexer Dual ‘‘D”’ Flip-Flop Hex buffer 7 stage ripple counter
NPN transistor PNP transistor Diode Diode Crystal Resistor Resistor Resistor Resistor Resistor Resistor PATTERN BOARD (PC A082-91355-C000) CHIP NUMBER 74LS00 74LS04 74LS74 74LS157 74LS161 74LS175 74LS257 74LS367 CD4555 MC14008 MC14013 MC14068 MC14174 MC14175 MC14516 MC14539 MC14572 FUNCTION Quad 2 input Nand Hex inverter Dual ‘‘D”’ Flip-Flop Quad 2 input multiplexer 4 bit binary counter Quad ‘‘D”’ Flip-Flop Quad 2 input multiplexer Hex bus driver Dual binary 1 or 4 decoder 4 bit full adder Dual ‘‘D’’ Flip-Flop 8 input Nand Hex ‘‘D’’ Flip-Flop Quad ‘‘D”’ Flip-Flop Binary up/down counter Dual 4 input multiplexer Multiple gate package
RAM BOARD (PC A082-91356-C000) CHIP NUMBER 74LS08 74LS14 74LS166
74LS253 MK4027 (MK4015) Additional Devices: 110 9 220 9 1K 9 0.1 ufd 15 ufd FUNCTION Quad input And Hex schmitt trigger Parallel to serial shift register Dual 4 input multiplexer RAM
Resistor Resistor Resistor Capacitor Capacitor
AUDIO AMPLIFIER BOARD (PC A082-90903-A000) CHIP NUMBER FUNCTION 2N4403 PNP transistor TIP 31 NPN transistor IN4004 Diode
POWER SUPPLY (PC A082-90411-A000) CHIP NUMBER FUNCTION LM317 Voltage regulator LM339 Quad voltage comparator $G3532 General purpose regulator Additional Devices: 79M05 Negative five voltage regulator 1N3235, Zener diode 2N3055 NPN transistor
MONITOR INTERFACE BOARD (PC A082-91373-B000) CHIP NUMBER FUNCTION LM339 Quad voltage comparator LM360 Differential comparator Additional Devices: MPS AZO Transistor MPS A70 Transistor
WIZARD OF WOR GAMEBOARD PC A084-90708-A961 CHIP NUMBER FUNCTION 74LS04 Hex inverter 74LS30 8 input Nand 74LS74 Dual ‘‘D’’ Flip-Flop 74LS86 Quad 2 input exclusive or 74LS153 Dual 4 to 1 line multiplexer 74LS161 4 bit binary counter 74LS164 8 bit shift register 74L$174 Hex ‘‘D’’ Flip-Flop 74LS257 Quad 2 to 1 line multiplexer tri-state 74LS367 Hex bus driver-tri-state 0066-117XX (2720) Custom !/O chip
LM358 OP-AMP
MC14099 8 bit addressable - latch - MC14099 8 bit addressable latch - Cmos MC14539 Dual 4 to 1 line multiplexer - Cmos scot Voice sound generator GORF GAME BOARD PC A084-90708-A873 CHIP NUMBER FUNCTION 74LS04 Hex inverter 74LS30 8 input Nand 74LS74 Dual ‘‘D”’ Flip-Flop 74LS86 Quad 2 input exclusive or 74LS153 Dual 4 to 1 line multiplexer 74LS161 4 bit binary counter 74LS164 8 bit shift register 74LS174 Hex ‘‘D”’ Flip-Flop 74LS257 Quad 2 to 1 line multiplexer tri-state 74LS367 Hex bus driver-tri-state 0066-117XX (2720) Custom I/O chip MC14066 Quad bilateral switch - Cmos MC14099 8 bit addressable - latch - MC14099 8 bit addressable latch - Cmos MC14539 Dual 4 to 1 line multiplexer - Cmos scot Voice sound generator
Z-80 CPU PIN DESCRIPTION
The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package.
The 1/O pins are shown in figure 3.0-1 and the function of each is described below.
SYSTEM CONTROL
ADDRESS BUS
CPU CONTROL
CPU BUS CONTROL
DATA BUS
Z-80 PIN CONFIGURATION
FIGURE 3.0-1
STRAPPING CHART
EXTRA BASES & SPACE ZAP
Single +5 Volt 2716 EPROM
2316E ROM
2332 ROM
l 2364 ROM
UPRIGHT CABINET
COCKTAIL
U8, U9, U10 are 74LS08
U8, U9, U10 are 74LS32
STRAPPING CHART GORF
ROM / RAM BOARD
DOMESTIC FOR ROMS
| 4 | 5 | 6 | 7 |
OPEN chose | GFetl | CLOSED | CLOSED | OPEN x-33 | CLOSED | OPEN ] CLOSED | OPEN CLOSED | CLOSED JoPeN |
DOMESTIC FOR PROMS OPEN X-31 | CLOSED
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |
| X-31 | CLOSED | CLOSED | CLOSED | CLOSED | OPEN |
X-32 X-33 | CLOSED | OPEN | CLOSED | oFeN foren | CLOSED | CLOSED | OPEN |
FOREIGN ROMS
| 1 | 2 | 3 | 4 | 5 | 6 | z | 8 |
[CLOSED | OPEN |cLoseD| OPEN | opEN | cLoseD| open | cLoseD | CLOSED | open | open | open |[cLoseD| cLosep| open | cLoseD | CLOSED | OPEN [CLOsED| oPEN | OPEN | CLOSED| CLOSED| OPEN | X-31 X-32
RAM/ROM BOARD
| CUT | JUMPER | JU20 | FOR | 74LS241 | LOCATION | U15 |
| * CUT | JUMPER | JU21 | FOR | 74LS244 | LOCATION | U15 |
| CUT | JUMPER | JU22 | FOR | 74LS32 | LOCATIONS U2, U3, U4, U5 | |
| * CUT | JUMPER | JU23 | FOR | 74LS08 | LOCATIONS U2, U3, U4, US |
GORF GAME BOARD
| CUT | JUMPER | JU2 | FOR | VOCAL SOUND |
| JUMPER | JU1_ | IN | FOR | COCKTAIL |
| JUMPER | JU1 | OUT | FOR | UPRIGHT |
LOGIC TERMS Z-80 SYSTEM
ADD Address
AUDIN Audio In
BUSAK Bus Acknowledge
BUSRO Bus Request
BUZOFF External Control
B-Y Blue Minus Video
BYTE Has Four Pixels
CE Chip Select
CAS Column Address Strobe
CASEN CAS Enable
D-O Data Out
DA Data In
DATEN Data Enable
lorQ Input-Output Request
HD Horizontal Drive (63.5 us)
INT Interrupt Request
1&0 Input - Output Signals
LTCHDA Latch Data
LITE PEN Interrupt Control
MD Memory Data
MA Memory Address
M1 Machine Cycle One
MREQ Memory Request
MUXD Multiplex Data
MC Micro Cycle Control
MENEN Memory Enable
NMI Non Muskable Interrupt
OG
PX
POT
PIXEL
RAS
RFSH
RAMSEL
RD
R-Y
SYSEN
SI
so
vD
VIDOT
WE
WRTCL
WR
RESET Phi-G Clock 1.7 MHZ
Monitor Picture Clock 3.5 MNZ
Control Potentionmeter
Smallest spot on color monitor screen with information
Row Address Strobe
Refresh
Ram Select
Memory Read
Red Minus Video
System Enable
Signal In
Signal Out
Vertical Drive (16.6 MS)
Video Out
Write
Write Control
Memory Write
Normally high an active low resets the Z-80
R G B BOARD SCHEMATIC.
TBA-530
+12
| Re | oe | +5 | Ru | |
| ik | 270NS | 9 | 750 | |
| ay ee | {ONQ9OOOS | T | 8 | |
| kza | R16 | vw >t | R | |
| 160 | 1K | aj | R7 | |
| RB | iF | 510 | ||
| + 75 | 12K | R13 | ||
| = | = | = | oK | Es |
+ rs Rs Ra Cc kev 3k 3k +12
iK
| 6-Y CT> | 4 | 'StNie ; |
| RIS | a7 | ui > + C)D 8 |
| 166 | 1K | 2 |
it -f i go Re
| = | = | = | (2k | 2k |
teow RB 29 3K 620 +2 = RZ
| CRI | = | 7 | ||
| Kg | IN52328 | = | lan | i |
| viDEO CI | je | 315 14} | CED 6 |
Ree y ag =5- 2K
| KEY CBD | — | T |
MO51 -0087 3-A030 None jezoeg ora MIDWAY MFG. CO. = PE RGB INTERFACE
coRS
9082 - 91363-9000
+e
SPKR #1
AUDIO
IN #1
AUDIO CZ) COMMON
ae)
a3 TWP-3)
KEY CD R3 2niw
FUSIBLE
SPKR#2
AUDIO. INH2 ql 2N4403, RE 2Aw
VAUDIO oo—r, +6v VAUDIO ‘ome 210 $05 +
test- play TEST, swi | ° MO51-00789-A0 12
PaaT ne. AUDIO AMP BOARD AO 82-90903-A000
CED key
Ja ke-100 ye KK-ISG
28A MO51-00873-A025 MIDWAY MFG. CO.
CONTROL GRIP PC ASSY
A082-91379-A000
WIRING SCHEMATIC — SPACE ZAP
“SPACE ZAP" MDWAY MFG. CO. 10750 W GRANO AVE, FRANKLIN PARK, IL. 6OL3/
WIRING SCHEMATIC PART NO,MO5I!- 00902 - A006
BACK PANEL BOARD PC. A0B2-93006-8/C00C MT65A XFORMER 60 CYC. PART NO, M@51- 00869-AGO8 MT66 XFORMER 50 CYC. t ' 220v H ro ve. '
| | | PC. A0B2-90411-A000 | Se | ew te | |
| ' | POWER SUPPLY | 28 Wey | ek | aa |
| | a RESET | 0-6 | lay | ||
| RED | 2 sv | ery | 5! | GAME LOGIC |
| S+———————-+< | Pc, A0B4-90700-4/0 76) 9 PSENSE G-R zy 546 | 12 PIN CONNECTOR 3 «<
| ON OFF | 4 | [GND | Oo | ei |
sw 1 Se
| 516 | GND | BLU-Y | o | | - | ty | a |
BLU rs ole) 'z Yo Yurs¥7 Yo Ya i Ve Ws Yo Ye Vo Va
| ‘ORN | s | | Lael | uf | —- | -|- |
~~ KEY "2 B- 491 PIN CONNECTOR i COIN METERP2_B-A aiu-ly
| a | 1 Zt | ew-r | CoN METER eT | o-w | 4 |
I iy up 8 B-W ono
REC} BRN cau own
BR-Y LEFT
y-G RIGHT
FIRE
TO CCIN DOOR , CONTROL PANEL + SPKR.
AUDIO BOARD PC. A082- 90903- A000 WPIN CONNECTOR
SIGNAL, BLK
AY IGNAL GND. $$ er r[—- -[--c}e7-|-7-[a js 7 wo ft ar MONITOR bea eS + Re
WIRING SCHEMATIC — GORF
GORF U.R, MIDWAY MFG. CO. 10750 W. GRAND AVE.
FRANKLIN PARK, IL, 6O!3!
WIRING SCHEMATIC * Mo5I--00873-A037
Rod MT8?-XFORMER, ——— BACK PANEL BO. fey pew yet PC. A082-93006- 84 G00 2204 come a ra 2c, noke-90411~ A000 POWER SUPPLY
1 hI GAME LOGIC 8D alsin con ne PC, nO 90760-0873 12 IN CONNECTOR,
19 CONNECTOR
prey +
fl
t
'
'
I
H
'
'
'
Hl
i
H
J
ROL Pc, nawa-91379- A000 10 .01% O0OR | CONTROL PANEL , SPAR,
orgy gsr
MONITOR. JACK
POWER SUPPLY SCHEMATIC
LM ay I x0] IOOOO MF 35V ELEC. AX. .1MF50V
= 2XiIN4001 re] > 2XAlSF 20000 MF 16 V ELEC. AX.
+— od
IMF 25V TANT
78 }+i2v 1.45 AMP t | 7 isi
|_6 j>= | Key
! iK (MF 25V | TANT
\7 | COIN COUNTER 119 | +5v (2. AMP REG FOR LOGIC)| 118. 45V 3 AMP’
I t
| 4 | RESET 16Vv AX. MF ELEC. A}
na 2XIN4001 ELEC. AX. + 2000MF 25¥ + 0.47 MF. 25V
TANT
SENSE
15-16! com 13-14] com It I 21-5v (450 mA) | 31 +V.IND.SIOVRMS AT 3.5AMP| : - i fo}
IOMF 16V +
14+ V, AUDIO 13V AT.L.5 AMP
roy | i | J2l—v,audio
Ht) —V. IND 4700 MF 25V ELEC, AX.
4XAI5 F LL4 —_—_—______! DISPLAY LITES DRAWING NO. MOS5I-00789-AOI!
COMMERCIAL CARD RACK PWR SPLY SCHEMATIC 082-9041 | A0O0O
GAME BOARD LAYOUT — SPACE ZAP
‘ 1
ora] ¥ (fa Ara) q sehler~
He POSITION TAKES # Le SocKEr
MIDWAY MFG. CO.
GAME BOARD SCHEMATIC — SPACE ZAP
wor os afr 8 rei de : town a
casey
saeer
seme
w1 er
eco
eurr
rol
coma
com 2
T2 MWA—CED TT
sean
TTTTT ;
2m lev Leve levs lew PTTPTPTTPTTT
L AIO AWC) rit y el Be Le mine mes MG) otmtd ) 800 .
noo 2
cere cme
seer eer
veo
one
con
wae oq rs plow rol Chl Ch? CR: LE gy may MIDWAY MFG. CO. Pe Srnce 2ar Gang senen |
1084-90708 - A908
GAME BOARD LAYOUT — GORF
Bu "|e. "I 8
De Gwe Qe G0 Ge ze Gct i) ew Der we
ue “9 Cis fuer
t
ped viz
sre y ue
ComPoN EST SIDE Viaw/
MO5 1-00873-C038
e-) Paglex [MOWAY MFG. co. |
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
CPU BOARD LAYOUT
a
O O O Sa
eH :
Component Sioe
MO5I-00789-A006
CPU BOARD SCHEMATIC
CED— VERTOR CaDD— HORZOR CD uco cp mc!
o WH
m2 tes 28 O.lmfd CAPACITORS (BP) NOT SHOWN
BOARD A082 — 91354 -E000 MO51I- 00789~- £005
A0G2-H355 -E000 H5le 4 4516 & a ez 39 Gi R fe Tp
MH17S- = 3 4175 14539 &4 145720
14516 34 @ SI Et L5/57 89 8 [es7 &¢ lso¢ =
19175 & 4 Hrs §§ ITA 84 flee 4 2504 §4
S [4008 §4 14008 §9 236784 4336784 8 Lste/ 4
14175 4 I4ITS §4 £8/25 $4 L875 § 3 lasses &3
> di é rab iv 45% &4 14516 § 8 14506 §3 /45t6 33 1457208)
oO Oy x i g : oO ° 48257 &4 8 { £8257 §4 £8257 &4 4068 84
ysis & [asi $4 yesie &3 B 14068 © 8 >
MIDWAY MFG. CO. PATTERN BOARD LAYOUT
PATTERN BOARD SCHEMATIC
MIDWAY MFG. CO.
RAM/ROM BOARD LAYOUT — FOREIGN
| 44 | ura | az |
xg x18
| ~ | ea, | ZTTEY |
7 BF) (Pad YLT a
x17
| Tae | 7 | rB77EY | |
| on | ve | = *23) | a x24 |
*
Xo
| T5350 | Giza) | ea | |
| u | ve | « xe} e | «Ree |
;
NS
| h502 | 57. | t598 |
| jet | u? | | We +4) ~ u3 |
:
xu
| £5138 | Case | 508 |
ule | C_ uo} el te ut cw
(s3z (508 | xa * : i us 0 us 68
PONENT 10E€ COMPONEN =a W- DENOTES wWH/cH PosiTiow RECIEVES Tb SOCKET”
MO51- 00873- A031 [Vag "*r | MIDWAY MEG. CO.
FOREL 2 bee "70 te lnnaase 2[- -=4900
RAM/ROM BOARD LAYOUT — DOMESTIC
132ft ow x18) (rm (m-
al
jr
{eo Pr] § Se) rr] bE) oH a PF
‘OMPONENT 10€ 7 sabia “0 We DENOTES WICH POSITION RECIEVES T.0 SOCKET-
MO51- -00873 - A032
DOMESTIC
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
oy £009-68200-FSOW "ON LYWd LNSNOdWOO toe tT poo9-sseie-280 Ir —a8" Quyog pee y poh t oz IH st vou L LNOAV1 GYuVvOs WV
RAM BOARD SCHEMATIC
74LS253
RAM BOARD SCHEMATIC PART NO. MOSI-00789~A002 ‘31 Oma CAPACITORS (BP) NOT SHOWN,
A082 - 91356 -C 9000
SERVICE BULLETIN
GAME: GORF
SUBJECT: NEW 6 CARD Z-80 SYSTEM USING A CARD RACK
GAME CARD (PC A082-90708-A873) | & O CUSTOM CHIP (TWO) TALKING CHIP - SC-01
ROM & RAM CARD (A082-91364-A000) DOMESTIC & FOREIGH (A082-91374-A000) RAMS 2114 ROMS 9316 OR 9332
CPU CARD (A082-91354-E000) 280 CPU ADDRESS CUSTOM CHIP DATA CUSTOM CHIP CRYSTAL 14,318
RAM CARD (A082-91356-0000) TWO RAM CARDS 16 RAM EACH (M4027)
PATTERN CARD (PC 082-91355C000) SHIFTS INFORMATION AT A FASTER RATE
POWER SUPPLY (PC 082-90411-A000) SAME AS SPACE ZAP
ANDY DUCAY SERVICE MANAGER
SERVICE BULLETIN
GAME: SPACE ZAP, GORF & WIZARD OF WOR SUBJECT: Custom chip identification (I/O, Address, and Data)
The following numbers will identify the special custom chip used in Space Zap mother board (PC 084-900002-B625).
TIO cece eee 2720 or 0066-117XX Address. .......... 0.00 e eee e ee 2719 or 0066-115XX [6 :| C: re rs 2721 or 0066-116XX or 2860
SERVICE BULLETIN
November 19, 1980
GAME: SPACE ZAP, GORF & WIZARD OF WOR
SUBJECT: Card Rack System Test Equipment
To aid board repair the following test cards are available
- A Ram Test Card to locate a bad Ram. A082-91516-A000
- A Card Rack Test Card which is used with the Ram Test Card and will also test the pattern card. A082-91517-A000
- Order test cards from the Midway’s Parts Department.
Andy Ducay Service Manager
AD/de
SERVICE BULLETIN INTERFACING DYNAMIC 4027 RAMS TO THE Z80
Sixteen-pin dynamic RAM’s are increasingly being used as the memory component for data storage in microprocessor - based systems. Their popularity over static and 18 or 22-pin dynamic RAM'’s has been the result of a maturing memory technology and the characteristics of the devices themselves. Their main features are low cost/bit and high bit density; additional features include a low standby power mode, TTL-compatible inputs and outputs and system-upgrading expansion capability. Replacing the chip-select pin on the 4K device with an additional address line effectively quadruples memory capacity to 16K bits. It is now possible, for example, to assemble a full 65K-byte memory system on a single printed-circuit board in an area of less than 50 sq. in.
Now however, the system designer must be concerned with the interface requirements of 16-pin dynamic RAMs. The characteristics of this memory element require that refreshing of the memory be performed at periodic intervals in order to retain the stored data. This, coupled with the requirement for multiplexing address lines, has been the main drawback to their use. A typical interface requires approximately 12 to 20 standard TTL devices and includes timing generators, decode logic, multiplexer circuitry, refresh logic and buffers.
The Zilog Z80A microprocessor is designed to simplify this interface with built-in refresh logic, which allows totally transparent RAM refresh without the need for a refresh counter or it’s associated multiplexer.
16-PIN DYNAMIC RAM ADDRESSING
Each cell of a dynamic RAM array is arranged in a matrix. Selection of a unique bit location within this matrix ina 4K RAM requires 12 address lines, while a 16 K RAM requires 14. For a 16-pin RAM to accommodate these lines, it must divide them into two groups - row addresses and column addresses (six each for the 4K RAM and seven each for the 15K RAM).
Each group is applied to the RAM on the same input lines through an external multiplexer and is latched into the chip by applying two clock strobes in succession. The first clock, the row-address strobe (RAS), latches the row address bits (A-0 to A-5 for 4K, A-0 to A-6 for 16K) into the RAM. The second clock, the column address bits (A-6 to A-11 for 4K, A-7 to A-11 for 16K) into the RAM.
Each cell therefore is uniquely addressed by row and column. When RAS goes active, all of the cells in the selected row respond (there are 64 rows in the 4K RAM matrix and 128 rows in the 16K RAM matrix) and are grated to sense amplifiers where the logic level of each cell is discriminated, latches and rewritten. CAS activates a column in the matrix (there are 64 columns in the 4K RAM matrix and 128 columns in the 16K RAM matrix) that uniquely identifies the cell in the row output and yields the required bit to the output buffer.
PIN CONFIGURATION 4027
-5 Cp GRND D-IN CAS
WE D-OUT
RAS cs
A2 A3
At Aa
AO AS
+12 +5