Warrior Operation and Maintenance Rev1
Warrior (Vectorbeam, 1979) · Manual · 68 pages · 40 sections · original scan
72-10919-01 Rev. 1 OPERATION and MAINTENANCE MANUAL
[-VECTORBEAM |
33441 CENTRAL AVE. / UNION CITY, CA 94587/(4158)4 XO
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
NOILVTIVISNI
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
INSTALLATION
Your new VECTORBEAM game has been designed to give you years of trouble free operation by utilizing proven solid state technology combined with rigid quality control throughout the manufacturing process.
Prior to installing your new game carefully remove the game from the shipping carton and inspect the cabinet for any external shipping damage such as dents or scrapes. Report any shipping damage immediately to the carrier and VECTORBEAM.
Two sets of keys are included with each game in an envelope taped to the control panel. Replacement and/or extra keys are available from VECTORBEAM upon request. In addition to the coin mechanism lock, the coin box itself is constructed to allow use of a padlock for addition security.
Your VECTORBEAM game may be powered from any three wire AC service outlet that will supply approximately 175 watts of power, The game has been pre~set to operate at the AC voltage specified on the decal located on the rear panel decal. If in doubt about your AC power source, check it with an AC voltmeter prior to applying power to the game. It is a good practice to test the AC service outlet with*combination receptacle circuit and ground fault tester prior to use. These are inexpensive devices that indicate voltage and correct wiring.
If your AC power is not the same as specified on the decal the power supply may be re-strapped to any of the three voltages specified in the AC Line Voltage Selection Tabie. If operating the game on any AC line frequency other than 60 HZ check the lamps and lamp ballasts to insure that these devices are rated for your line frequency.
The cabinet should be located within five feet of your AC service outlet if you plan to use the game without an extension cord. If an extension cord is to be used it should be of the minimum length necessary and should be of heavy duty three wire construction.
The warranty is void if the game is used with the third wire ground prong broken off the line cord. This is an unsafe condition and must be corrected. Line cords are available from VECTORBEAM to replace damaged or broken cords.
Your game will power up as soon as the line cord is installed in the AC service outlet. The game, after it is properly installed, should be checked operationally by performing the following procedures:
- Prior to applying power to the game remove the rear door and check to insure all connectors are firmly seated.
- Check the power supply fuses to insure that they are correctly installed and are of the proper rating.
- Plug in the AC line cord. Since the rear door is off, the interlock switch on the rear door cleat will be defeated and no AC should be available at the power supply. To defeat the interlock when the door is removed, pull the white plunger out. Allew the cathode ray tube (CRT) one to two minutes to warm up.
When the rear door is off and the interlock defeated there are high voltages present in the game. Do not attempt to remove or reseat connectors in this mode. Always have the AC disabled when removing or reseating connectors. :
Observe that the display is active and all lamps are functioning. If there is no display refer to the Maintenance and Adjustments and Trouble Shooting chapters of this manual.
Your Vectorbeam game is equipped with an option switch located on the Logic Printed Circuit Board Assembly. This switch has been pre-set at the factory. Refer to the Option Switch Table in the Game Play chapter of this manual for the various settings.
Open the coin door and trip either mechanism, the coin counter should increment each time the trip wire is activated. If the game is set for more than one coin the coin counter will still increment but the game will not be enabled until the correct number of coins have been inserted. Refer to the option switch table in the game play chapter of this manual for multiple coin options.
After the game has been activated the game will be in Play Mode. The audio and controls will be active at this time. Refer to the Game Play chapter of this manual for display and audio adjustments. Follow the game play description to insure all functions are . operational.
After any display and audio adjustments are made, replace the back door and make final placement of the game. If the game is not level it may be necessary to shim the bottom of the cabinet to prevent rocking.
Game Description
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Introduction
"WARRIOR" is a two player vector generated video game designed to give the player realistic sword fighting action. The three dimensional effects brought
about by the playfield and the high video resolution of the VECTORBEAM!™ monitor
are only part of this. The feeling of realism is also brought about by the energy
hum in the audio circuit and the spectacular artwork by renowned fantasy artist
Frank Brunner. The following paragraphs explain how the game plays.
Game Play
There are two modes of operation to your "WARRIOR" unit: The Attract Mode
and Play Mode. The Attract Mode is activated when power is applied or a game has
ended. The Play Mode is activated when coins are accepted and play is ready to
begin.
- Attract Mode
The Attract Mode appears on the monitor screen a few seconds after the monitor
is powered up or at the end of a player's game. As the Attract Mode begins,
the swordsmen materialize in their "safe zones". From there they move up the
stairway to their immediate right. (Notice how the swordsmen get noticeably
larger as they ascend the staircase and noticeably smaller as they decend it.)
They then proceed to the center of the screen (between the "bottomless" pits)
where they raise their swords and begin fighting. One swordman will then
explode and the surviving swordsman falls into one of the "bottomless" pits.
The Attract Mode exists to give the prospective player an idea of how the game
is played, and also serves to show the operator that the safe zones, pits and
staircases are aligned correctly.
- Play Mode
The Play Mode is activated when the players’ coins are accepted. Players insert
two quarters for the first ten (10) time units and each additional quarter gives
ten additional units. The duration of the time units is set by the operator
(for instructions, see "Operator Option Switch" at the end of this section).
Time units are displayed on the bottom center of the display. Scores are on
the top left and right.
The object of the game is to score points in one of two fashions: a.) by
touching the center of your opponent with the end point of your sword or
b.) by forcing your opponent into one of the "bottomless" pits. Each of
these scoring moves scores one point. The player with the highest total
at the end of the game is the victor and his score will flash brighter
and dimmer when the game is over.
Each swordman is controlled by the joysticks on the player control panel.
at the top of each joystick is a black push button. Moving the joystick
without the button depressed moves the swordsman's body in the corresponding
direction. Moving the joystick with the button depressed moves the end
point _of the sword in the corresponding direction. The swordsman's body
and sword cannot be moved simultaneously.
When a point is scored, the scoring swordman remains in place. The swordsman
scored upon reforms in his respective "safe zone". Both swordsmen must be
outside their "safe zone" to be scored upon.
OPERATOR OPTION SWITCH
The operator option switch is located on the Logic PCB. This switch allows the operator to set the game time to 30, 60, 90, or 120 seconds, set the coin acceptor to one or two coins and also to display an alignment image on the CRT.
NOT USED
On On 1 Coin Off = 2 Coins Allign Image Off = Normal Play On _ Off _ Off 120 Sec. oft = 90 Sec. On 7 60 Sec. OFF = 30 Sec.
Maintenance
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
MAINTENANCE and ADJUSTMENTS
Cleaning VECTORBEAM is proud of the appearance of your new game. To keep it looking "fresh" periodic cleaning is recommended. Use a non-abrasive household cleaner diluted with warm water, a soft cloth and a little effort will keep your game attractive for years. Care should be exercised when cleaning the player control panel, decals and plex. These surfaces can be marred and scratched if subjected to abrasives.
Coin Mechanism a. Coin Counter The coin counter, located next to the coin box, is a highly reliable electro-mechanical counting mechanism that is incremented by the electronics. No maintenance is required for this device. By opening the coin-door you can insure proper operation by toggling the coin mech and observing the counter increment.
b. Coin Mechanism To insure proper operation of the coin mechanism is is necessary to periodically clean the coin path of residue that builds up. Do not use abrasive brushes. Hot soapy water and a toothbrush followed by clean water flushing will remove the residue build-up. Use compressed air to blow dry the mechanism. Do not use lubricants as this will result in a rapid build-up of residue in the coin path.
c. Troubleshooting Jammed coins are the most common problem with coin mechanisms. After removing the coin examine the mechanism to determine the cause. Remove any foreign objects such as gum or paper wads and clean the coin paths. Failure of the coin to register can usually be corrected by adjusting the trip wire. In some cased is may be necessary to check the coin mechanism wiring to insure the connectors are firmly seated. Failure of the electronics to register the coin is very rare. If the mechanism and wiring appear to be functional the logic may be examined by use of an oscilloscope. Refer to the logic schematic for coin register circuit diagram.
Fuse Replacement There are two fuses contained on the power supply. These fuses are accessible through the rear door. Prior to replacing or checking fuses insure that power is off. Always replace fuses with the same type and rating.
X & Y Gain Adjustment Refer to Display Assembly drawing for component location. a. Set game in Adjust Mode (see Game Play for switch setting.) b. Turn X gain trimpot R60 until display is centered to pits. c. Turn Y gain trimpot R54 until display is centered to pits.
Centering Display ; In some cases it will be necessary to move the yoke radially on the CRT neck to obtain perfect centering.
Plex Removal Remove the two button head screws securing the plex to the cabinet. Push plex up to clear the joysticks then pull bottom of plex over the joysticks and clear of the cabinet. In some cases it may be necessary to loosen the control panel in order to free the plex.
Control Panel Removal If the control panel is damaged or is malfunctioning it is necessary to remove the assembly to gain access to the joysticks. . a. Turn off power. b. Disconnect the coin door harness. Unplug joystick .connectors. c. Remove the hex nuts and carriage bolts on the sides of the control panel. d. Remove the control panel assembly from the cabinet.
Joystick Adjustment Determine which joystick and function is non-operational. If the malfunction is caused by the pushbutton switch located on the top of the joystick handle the grip may be removed and the pushbutton switch loosened and removed for repair or replacment. If the malfunction is due to the failure of one of the four leaf switches controlling the movement of the Warriors, it is necessary to remove the control panel in order to Te-adjust or replace the leaf switch. To adjust the leaf switch use a pair of needle nosed pliers and bend the stationary leaf only. Insure that all of the terminals attaching the harness to the joystick leaf switches are firmly seated and not shorting.
Lamp Replacement (turn off power) a. Flourescent Lamp Remove the rear door and insure no power is available to the game. Remove the two stopblocks securing the playfield bezel. Fold the playfield bezel up to clear the lamp carrier. Remove the flourescent black light and replace with lamp of the same rating; F1ST8/BLB. Re-install the carrier, stopblocks and rear door. b. Top Lamp Remove the rear door and insure no power is available to the game. Remove the top lamp and replace with a lamp of the same rating; F15T8/CW or F15T8/WW.
VECTORBEAM MONITOR OPERATION
The VECTORBEAM'™ monitor can be divided into two basic sections. One section is the deflection amplifiers, and the other section is the high voltage and cathode drive circuit.
The deflection amplifier can be further divided into two identical channels: one for vertical deflection, and one for horizontal deflection. We will describe the operation of only one channel (vertical) and the same theory of operation will hold true for the horizontal section.
Digital information, in the form of a twelve-bit word, is applied to the input of the DAC-80 digital to analog converter US on pins one through twelve. The most significant bit (MSB) is applied to pin one, and the least significant bit is applied to pin twelve. The DAC-80 makes the necessary conversion from digital signals to analog signals which are outputted as analog voltage signals on pin fifteen (which is proportional in level depending on the input word applied). The result is a positive and negative voltage signal about its reference voltage (remember, there is no "sync" signal present, and the signal is not true video as seen in raster scan monitors).
From the DAC-80 the analog signal is then sent to a high-speed analog switch, U3. The analog switch has two parallel inputs for the display signal, and two controlling inputs which select one of two outputs from the switch. At the outputs is found an R.C. network, which is used to create line length and line position on the screen.
Output fifteen from the switch routes the analog signal through a SK potentiometer R58, a 10K resistor, R59 and to the input of U4 op-amp. The time constant developed by these two resistors and the capacitor C35 determine the length of the vector line seen on the screen. Adjusting the potentiometer will adjust the length of the vertical lines seen on the screen.
Output ten from the analog switch routes the signal directly to the input of U4 op-amp, and the resulting time constant of the op-amp input impedence and the capacitor C35 determines the position on the screen of the vector line.
Op-amp, U4 serves a dual purpose: one, it acts as a buffer between the deflection amplifiers and the analog switch; and two, it acts as an "edge gain" amplifier (i.e., height).
At the output of U4 there is a resistor amp, diode network consisting of R52-R57, and CR27-CR30. This resistor diode network is used to compensate for the non-linear characteristics of the CRT near the edges of the screen. If this circuit were not used, any object displayed on the screen would increase in size as it moved closer to the edges of the screen. Also contained in the circuit is a potentiometer R54, which adjusts the height of the pictures. :
From the wiper of R54, the signal proceeds to Q17, which is the first stage of deflection amplification. Q18 is emitter coupled with Q17 to provide a degenerative feedback loop from the yoke. Q!6 is used to proved a constant current source to both emitters.
At this point, the deflection circuit can again be divided into two identical circuits. One circuit, which controls the lower half of the screen, is comprised of Q8, Q9, and QlO. The other circuit, which controls the upper half of the screen is comprised of Q7, Q12, Q6, and Qill.
Q8, Q10, and Q110 are three stages of amplification, while Q9 is used as a current limiting protection for Q10 and Ql110. The same holds true for the other configuration of Q7, Q6 and Ql11. R23 through R28 are used as a current divider network for the yoke. .
In the horizontal section of the deflection amplifier, Q3, Q2, Ql, and Q210 control the left hand side of the screen, and Q4, Ql1, Q5, and Q211 control the right hand side of the screen. By dividing the screen in this manner, four quadrants of deflection area have been developed (see vector theory chapter.)
R38 and C37 form an R.C. network, which compensates for any CEMF that may develope by the expanding and collapsing of the deflection coil's electromagnetic field.
The high voltage and cathode circuitry is the second section of the monitor. This section also contains the necessary voltage regulation to power the IC's located on the display board as well as develop the high voltage.
U10 and Ul11 provide plus 15V and minus 15V respectively to power the DAC-80's and the TLO81 op-amps on the diplay board.
U9 and U12 provide plus 18V and numus 18V used in the high voltage transformer (T-1) and oscillator (The oscillator circuit is necessary because there is no horizontal sync used to develop the high voltage pulses.) The oscillator circuit is comprised of primary windings, Q31 and associated discreet components. U8 provides the plus 5V for the 7406 and protection circuits.
The high voltage 18KV is developed by Tl secondary windings, the high voltage tripler, and the focus circuitry. The potentiometer, R92, is used to adjust the focus of the cathode beam.
One of the secondary windings of T1 develops the necessary cathode voltage, which when Measure at, the cathode of CR51 should read 88VDC. The cathode circuitry in the VECTORBEAM™ monitor is comprised of U6, a 7406 IC used for buffering logic signals which control brightness and blanking. It also contains the transistors, Q20 and Q21, and Q22, and then associated discreet components.
Q20, and the first gate of U7 control the brightness of the cathode signals upon command of the CPU logic board. Q22 and the second gate of U6 control the intensity (blanking) of the cathode signals, also upon command of the CPU board. Q24 is used as a power failure protection for the cathode circuit in the event of a loss of 25V power supply voltage. This protection aids in avoiding phosphor burning on the CRT. R91 is the brightness potentiometer, which adjusts the amplitude of the negative soing spikes used for brightness and intensification.
THEORY
OF
OPERATION
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
CPU BOARD
The processor hardware can be broken down into five basic
functional blocks as shown in Figure 1. The arrows indicate the possible
data flow directions between the various blocks. The ALU and Control
block are the main components of the processor while the Memory and 1/0
blocks may be thought of as merely peripherals. Figure 2 is a detailed
block diagram of the processor. The numbers in each block correspond to
the entires in Table 1, which lists the IC numbers of the main components
of each functional block,
The following is a brief description of each block shown in
Figure 1. The numbers beside each functional block name are the numbers
in Figure 2 which correspond to a particular function.
RAM (6)
The RAM is implemented with three 9101C read/write static memories
configured as a 256 x 12 bit block, Data can be transfered to or from this
memory via the ALU block. The processor uses this RAM as a scratch pad,
BOM (10) The ROM is configured as an 8k x 8 bit block of memory. These
memory locations contain the program instructions and/or data. It is accessed
via the processor control unit.
1019, 17, 18 The 1/0 block consists of 8 input lines implemented with a bit
addressable latch, 24 input lines implemented with data selectors, and two 12
bit registors which are connected to the X Y display deflection circuits via
D/A convertors.
10.
Arithmetic Unit 1,2,3,4,5
The arithmetic unit performs all the arithmetic processing for* the
system. It consists primarily of two 12 bit accumulators, an arithmetic
logic unit and various data selectors, The accumulators can function as
temporary storage registers for arithmetic calculations, or as the source
and destination registers for 1/0 operations. The ALU performs the actual
arithmetic functions upon the data in the accumulators. The data selectors
are used to select the various sources of data which will be processed.
Control Unit (15, 16, 14, 7, 8, 9, 11, 12, 13)
The control unit is the heart of the processor, It performs
all instruction decoding operations and generates all the necessary control
signals which the rest of the hardware requires to function correctly.
The following is a discussion of each block shown in Figure 2.
- Accumulator Selector
The accumulator selector consists of 3 quad data selectors.
They are used to select the output of either the primary or secondary accumulaotr
for processing by various other sections of the system.
- & 3. Primary and Secondary Accumulators
The two 12 bit accumulators are implemented with quad bidirectional
shift registers. The primary accumulator consists of S4, P4, M4. The
secondary accumulator consists of T4, R4, N4. All data manipulation in the
processor is accomplished using these two accumulators, All output data flows
through these registers,
4, Arithmetic Logic Unit (ALU)
The ALU is used to perform all necessary arithmetic functions within
the processor. The ALU is implemented using three 25LS181 (N6,M6,L6) function
11. generators, three 74LS85 (N9 M9, L9) 4 bit magnitude comparators, and a
748182 (L4) look ahead carray generator. The data which the ALU manipulates
can come from four different sources. The first source is the contents of
the accumulators via the accumulator selector. The second and third sources
are the ROM and RAM data outputs via the ALU data selector (N11, M11, L11)
and the fourth source is the external input lines via the input selector
(E4, D4, C4).
- Data Selector
The data selector is used to read data into the ALU from either
the RAM or ROM memory. Note that the ROM data is only 8 bits wide while the
RAM data is 12 bits wide.
- RAM Storage
The system RAM consists of three 9101C high speed static memory
chips connected as a 256 x 12 bit block. The block is 12 bits wide in order
to allow the contents of an accumulator to be stored. The processor uses the
RAM as temporary storage of program variables, data pointers or any other data
of a dynamic nature.
- RAM Address Selector/Register.
The output of this register is tied directly to the address lines
of the RAM. It consists of a multiplexer which routes address data from either
the ROM or RAM locations to the RAM address lines. The capability to use RAM
data to select RAM addresses is the basis for the indirect addressing mode of
the processor.
- Page Selector
The page selector is used to latch the high order 4 bits of a RAM
address during some types of RAM access instructions.
12.
- ROM Data Register
This regiater is used to temporarily hold data from the ROM
during an instruction fetch.
- ROM Menory
The ROM memory consists of the actual memory chips plus a data
selector and latch circuit. The latch is used to improve the memory access
time during a two byte instruction fetch by allowing one byte of the instruction
to be latched while the RAM address lines are decoded for the other byte.
The data selector can then be used to rapidly access both bytes of the instruction
by switching between the latch and memory outputs.
1l. Instruction Register
The instruction register ig a latch which holds the current op
code as read from the ROM. Its output is tied to the instruction decode circuitry
which in turn generates the necessary signals to execute the instruction.
- System Sequencer
The system sequencer is used to decode an instruction op code
and to generate the appropriate timed sequence of signale which execute the
instruction. The op code is decoded by usingit as the address data to a set
of decoder ROMS. The outputs of the decoder ROMS are then synchronized with
the system clock and used to control the various system functional blocks.
13, Line Length Counter
The line length counter is used during the process of drawing a
vector to control the length of a vector, by turning off the beam at a pre-
determined time after the vector is initiated. The counter is loaded with a
value from a line Length ROM and then counts up uatil it overflows which in
turn generates a signal to indicate the vector has been finished.
13.
- Program Address Selector This selector is used to provide the address data to the -program
ROM. It selects either the program address counter output or the accumulator
selector output and routes this data to the ROM address lines. The ability to
use the accumulator contents as address data allows the program to randomly
access data tables stored in the ROM or to compute a branch address after a
conditional test.
- Program Address Counter
This is a 12 bit counter whose output defines the next location
in ROM to be accessed, It is normally clocked sequentially to step through a
program, However, it can be loaded with data from the program address register
which is how the jump instructions are implemented.
- Program Address-Register
This register is a latch used for temporary storage of an address
which will be loaded into the program counter during a jump instruction. The
input data to this latch can come from either the program ROM or the scratch-
pad RAM.
- Input Selector
The input selector is used to read the state of one of the 24 input
lines into the selected accumlator. There are 16 primary inputs and 8 secondary
inputs. During an input instruction the upper 11 bita of the accumulator are
set to zero while the least significant bit reflects the state of the input line.
All input lines have pull up resistors on them so that they will read high if they
are left unconnected,
14,
1 Output Selector
The output selector is a bit addressable latch used to
control the 8 output lines. During an output instruction the selected output
line is set to the complement of the least significant bit of the
accumulator, The output lines are used to control the audio board, display
intensity and the mechanical coin counter.
- Display Registers
The display registers are the interface between the
proceasor and the display driver circuits. These registers are latches
into which the contents of the accumulators
are tied to D/A converters which provide the input voltage to the display in be stored. The outputs
deflection amplifiera.
(Give (Foe sear
PROPRIETARY
THIS DOCUMENT 18 THE PROPERTY
OF VETTE AH AND 18.
MOT TO BE AEPRODUCED OF
DISTRIBUTED WITHOUT WAITTEN AUTHORIZATION OF VEC TOKE Dany REVISIONS:
REV DESCRIPTION ‘DATE
Yol_10
DISPLAY
ACCUM —{DISPLA’ SELECIOR ne [ADORESS ©) Counts ADORESS en fuiné (3)
CCUNTER)
PRIMARY, SECONDARY (ADDRESS; ACCUM Gta (©) [tae fou
[ae fa PARUTHMETIC Gam
uit @) es Ss. + | GAME Sve t SEGUENCER|
(oil) T
SELECTOR PAGE 6 ROM ha ROM SELECTION [~~ REGISTER ® MEMORY FEB 28 wy
PROJECT ENGR: VECTORBEAM “DWG TITLE BLOCK DIAGRAM [BO NOT SCALE Owe|CPLU BOARD — DETAILED memerpeec|_ La|s0201000 "| “f55- -@- [NONE [coor eer ancer Zor
FINISH: BREAK ALL SHARP EOGES AND DEBUAR ALL HOLES, US .
Intensity
Simplified Block Diagram of The System Sequencer Display Section 16.
The Line Length Timer Simplified Block Diagram of
PRESET
DECODER
12-BIT PRESETABLE | [+ LINE DONE
COUNTER
17.
Vector Generator Block Diagram WORKING
STORAGE
RAM (eum 1 Qkneosren raePant
Qvacoisten seconpaRy
ACCUMULATOR
saesane
(Te Rane TO THE MONITOR DispLay soano ouRaTion 18,
TERMINAL AouustaaLe COORDINATE REWETWORK
‘SWITCH ce cunnent
! 5
‘swine,
ml
Simplified Block Diagram of The Display Electronics PCB (one-half analog section) VeRticaL DEFLECTION Con. oniveR wo Feeneack
va Z AS —— 0IRECTION OF LINE SEGMENT DISPLAYEO WHEN
7 INTENSITY INPUT TURNS ON BEAM CURRENT TOCRT
qe, AL POINT 19,
20.
WARRIOR Audio Board
The WARRIOR Audio Board is a self contained electronic sound generation system that requires connections only to external power, control and loudspeaker. - Sounds generated include a pit fall, explosion, reappearance hiss and two levels of sword hun.
The audio power amplifier consists of the op-amp IC19, power transistors Q6 and Q7, capacitors C38-C40, and resistors R58-R62. The volume is controlled by potentiometer R63. The circuit can drive and 8ohm loudspeaker to approximately 8 watts RMS power.
Each sound is enabled by a command from the logic PCB via a 16 pin ribbon cable to connector J2. Power and speaker output are connected through the 9 Pin molex connector Jl. Two on board voltage requlators supply the +15VDC and -15VDC to the circuits.
The wideband noise generator is used as a white noise source for the sword hun, explosion and reappearance hiss. The wideband noise generator consists of the diode D1, IC5-7 and their associated circuitry.
The explosion circuit is triggered by a 400ns pulse from connector J2 pin 14 to pin 2 of IC 4 which enables IC 2 for the duration of the explosion (approximately 1.5sec.).
The reappearance hiss is generated by J2 pin 15 to IC 8 pin 12. The output of IC 8 pin 12. The output of IC 8 pin 11 will allow the reappearance hiss sound to be enabled through IC 3 as long as IC 8 pin 13 is held low.
The sword hum circuit generates two levels of sound; sword hum high and sword hum low. The low sound is generated by a low logic level on J2 pin 11 which enables IC 3 pin 3 which will then apply a voltage on the amplifier bias imput of IC 13, pin 5. When J 2 pin 12 goes to a low logic level it will enable IC 8 pin 6 increasing the voltage to the amplifier bias input of IC 13 pin 5. The input to IC 13 is the free running sword hum noise generator comprised of IC 9 and its associated circuitry and the output of the wideband noise generator.
The pit fall circuit is enabled by a low logic level on J 2 pin 14 triggering the one-shot IC 14 and enabling the output of the pit fall circuitry to be gated by Ic 8 to the op-amp IC 18.
APPENDIX
A
REFERENCE SCHEMATICS
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
21. TROUBLESHOOTING CHART
PROBLEM PROBABLE SOLUTIONS
CIRCUIT Disconnect AC line power to Display PCB BREAKERS If breakers continue to blow, check for BLOW ( shorted speaker coil
Check logic PCB for lighted LED, located near power connector LED should not be on Measure voltage at pins 10 and 20 at T13 Voltmeter should read 4.8 VDC
i Remove Molex connector U4 and US Check power transistors Q110,Q111,Q210 and Q211 located on headsinks with ohmeter
Check diodes CR34 and CR35 located on display PCB
i Disconnect CRT yoke by removing Molex connector from display PCB Remove CRT socket. Reset breakers Apply AC line power. If unit fails to blow circuit breakers, check all transistors with ohmeter comparing readings between horizontal and vertical sections
Check diodes CR12 and CR22 located in vertical drive section Check diodes CR1 and CR11 located in horizontal drive section
Check voltage at horizontal and vertical DAC's at pins 13, 14 and 22
Measure outputs of amplifiers U2 and U4 for DC offsets. Signal should be a + 2 volts centered around 0 volts
Measure outputs of DAC's U5 and U11 Signals should be + 4 volts centered around 0 volts
j—__
DISPLAY Check vertical size potentiometer R54 for wiper JITTERS noise by turning R54 briskly while observing screen, Check R54 pins for weak solder connections.
[
22.
Troubleshooting Chart
PROBLEM PROBABLE SOLUTIONS
Check horizontal size potentiometer R60 for wiper noise by turning R6O briskly while observing screen. Check R60 pins for weak solder connections.
Check DACs U1 and US pins for poor solder connections.
Check Molex connector pins for good connections.
Check analog switch device U3 for loose pins or poor solder connections on socket. Replace U3,
One-inch Check for open power transistors Q110, Q111, Q210 and Horizontal Q211 using an ohmmeter:
Line, Displayed
A he . on monitor Check Molex connector to power transistors for open or weak solder connection.
Check the neck of CRT for glowing filament. If filament is not glowing, check brown and black twisted wire pair to CRT plug for 6.3 VAC.
LED on logic PCB should not be on.
Zero scope. Connect scope probe to yellow beam wire at display PCB. Set brightness full clockwise. Data pulses should be 50 volts at an 80-100 VDC base.
If no data present, connect scopeprobe to pin 4 of U6. Then dynamically check Q19 for an open collector to emitter junction (41VDC on emitter). Check Q20 and Q22 with ohmeter. Connect scope probe to the cathode of CR32 and check for a full-wave, unregulated spot kill voltage (approximately 25 volts DC). If not check power supply fuse and check Q14 and Q21. Check 18KV at anode cap of CRT. (Use high voltage probe.) If high voltage not present see No High Voltage remedy. Check CRT neck for broken pins. Check the seating of the TRT plug.
-cont'd
‘Troubleshooting Chart
NO DISPLAY cont'd
No High Voltage
Dot Display Remove AC line power to game Remove CRT plug from CRT neck Return AC power Measure pin 3 of CRT plug with oscilloscope. Meter should read 400 VDC.
Measure pin 4 of CRT plug with oscilloscope. Meter should read 200 VDC.
Connect scope probe to yellow beam wire at display PCB. Set intensity control to full clockwise. Data pulses should be 50 volts peak to peak at an 80-100 VDC base.
Measure the AC voltage at pins 1 and 8 of the CRT plug. Meter should read 6.3 VAC.
Measure DC voltage of regulator U12 Meter should read +18 VDC If not present, measure DC voltage at capacitor C25. Meter should read + 25 VDC.
Measure DC voltage of regulator U9 Meter should read -18 VDC.
If not, measure DC voltage at capacitor C17. Voltmeter should read —25 VDC.
Lift winding from pin 3 of high voltage transformer T1. Measure + 18 voltage regulators If +18 VDC present check Q31 for short Check capacitors C32 and C34 for shorts Check diodes CR46 and CR47 Check GKV AC on black wire. Check CRT for bent pins
Check analog switch U3 Inspect yoke connector for poor solder connections Check for open yoke winding Measure DC voltage at capacitor C7 Meter should read +25 VDC Measure DC voltage at capacitor C1 Meter should read -25 VDC
PROBLEM
Narrow
Line Displayed
Half Display
- Left Half Missing
- Right Half Missing
- Top Half Missing
- Bottom Half Missing
Brightness Potentiometer has no Control
Circuit breakers Blow after warm-up 24,
Troubleshooting Chart
PROBABLE SOLUTIONS
Check for open yoke winding . Check yoke Molex connector for weak or cracked solder connections
Check Molex connector continuity to Q110. QI11. Q210 and Q211. Check for open power transistors QI10, Q111, Q210 and Q211
Check Q1, Q2 and Q210 with ohmmeter
Check Q5, Q11 and Q211 with Ohmmeter
Check Q6, Q12 and Q111 with ohmmeter
Check Q9, Q10 and Q110 with ohmmeter
Check intensity potentiometer R91 wiper
Check for open C28 capacitor
Check potentiometer pins for weak solder connections
Measure DC voltage at pins 10 and 20 of device T13 on the logic PCB. Meter should read 4.8 VDC
Check for thermally sensitive 723 regulator devices on the power supply
Check for thermally sensitive devices on the Logic PCB
Troubleshooting Chart
PROBABLE SOLUTIONS
PROBLEM
Check for thermal sensitivity of devices U2. U3. Ui US and ULI Check operation at DAC US Check operation of DAC U1] Check tor thermul sensitivity of Q15. QI0. RI2 and Rx”
REFER TO PAGES 26 and 27 for Audio Troubleshooting
Does Not Provide Game time When Coin Inserted Remove AC line power Remove 3-pin Molex connector to coin mechanism
Check switch closure with ohmmeter (Center pin of connector is common) Verify one pin normally open and the other normally closed Press coin device at coin mechanism. Pins should change state. Normally open to normally closed and vice versa.
Check flip-plop A4 on logic PCB with logic probe on pin 3 of AA. Press coin iever: Pin should change state. With logic probe on pin 6 of A4, press coin lever: pin should change state.
Replace device F2 on logic board.
Coin counter Check transistor 2N3904 and 2N6292 on loyic PCB with does not Work ohmmerer
Disconnect coin counter Molex connector Measure DC voltage on red wire Meter should read + 25 VDC
Check power connector (JI) to logic PCB
Check electrical connection at pin 3 of J (white wire) 25.
26.
PROBLEM PROBABLE SOLUTIONS
With ohmeter, check for open speaker coil. Verify proper operation of IC10 and ICll, +15 volt and -15 volt regulators
Check power transistors Q6 and Q7 with ohmeter.
Replace IC19 (TLO81) Replace device F2 on logic board (74LS259)
NO SWORD HUM Jumper pin i of IC8 (74LS125) to ground. If sword now present, check continuity between IC8, pin 1 and F2, pin 4 on the logic board.
Replace device F2 on logic board. Check transistor Q4 with ohmeter.
Verify proper operation of 1C13 (CA3080)
NO HIGH LEVEL Jumper pin 4 of IC8 to ground. If higher level SWORD HUM now present, verify continuity of IC8, pin 4 to F2 pin S on logic board. Replace device F2.
Check transistor Q3 with ohmeter. Replace IC8.
NO PITFALL AUDIO Jumper IC8 pin 10 to ground. If audio now present, check continuity between IC8, pin 10 to F2 pin 7 on logic board.
Replace device F2.
Verify proper operation of IC18 (CA3080)
Observe output of oscillator IC16. Pin 6 should be 80% duty cycle, slightly frequency modulated.
Check transistor Q5 with ohmeter. Replace IC8.
27.
PROBABLE SOLUTIONS PROBLEM
PITFALL AUDIO DOES NOT DECAY Jumper pin 4 of IC14 to ground while observing output of pin 6 with oscilloscope. Pulse should be approximately 15 milliseconds in duration, at 4 vDC.
Verify proper operation of IC15 (7406 - open collector)
| PITFALL AUDIO | Observe pin 3 of IC17 (NE555). Output should be | i |
DOES NOT WARBLE square wave at 14 volt level and 44 millisecond
| E | period. | } |
Check C32 for open.
NO EXPLOSION, Verify proper operation of wideband noise generator DISTORTED IcS, IC6, and IC7. Output of IC6 should be random
| EXPLOSION AUDIO | : | noise signal approximately 1.2 volts peak-to-peak. |
H Output of IC7 should be random noise signal approx-
| i | imately 5.2 volts peak-to-peak. | j |
| Replace zener diode D1 (IN5220)
Attach jumper to IC4 pin 2. Momentarily touch to ground while observing one-shot output pin 3. A single pulse of .6 second duration should occur.
Check Ql with ohmeter. Check capacitor C14.
i Verify proper operation of IC1 and IC2. Replace device F2 on logic board.
| NO | | | Jumper IC8 pin 13 to ground. If audio now present, |
REAPPEARANCE check continuity from IC8 pin 13 to F2 pin 9 on HISS logic board.
Replace device F2 on logic board. Check transistor
Replace IC8. Verify proper operation of device IC3.
Verify proper operation of wideband noise generator IcS, IC6, and IC7. Output of IC6 should be random noise signal approximately 1.2 volts peak-to-peak. Output of ICs should be random noise signal approximately 5.2 volts peak-to-peak.
28.
SUGGESTED PARTS FOR STOCK
Due to the fact that the VECTORBEAM™ system is a new type of display technology, | there are a number of components used which may have limited availability from your local parts suppliers. It is suggested that the following list of parts be purchased in the even servicing of your game becomes necessary:
- TL182 - Analog Switch
- TLO81 - Op-Amp
- 7918 - Regulator IC
- 7915 - Regulator IC
- 7818 - Regulator IC
- 7815 - Regulator IC
- LF13331 - High Speed Analog Switch
- DAC-80 - Digital to Analog Convertor
- 7415259 - IC (Texas Insutruments only)
- 74LS32 - IC
- Set D-ROMS (1-6)
J5 VERTICAL DEFLECTION DEVICES Qil0, QUIT {SEE NOTE 1)
3B HORIZONTAL DEFLECTION DIVICES Q210,Q211 (SEE NOTE 1) VERTICAL/HORIZONTAL DEFLECTION cols
R54 Y DRIVER INPUT. ADJUST
x DRIVER INPUT ADJUST R60 x RC TIME
CONSTANT ADJUST ul X DAC 29.
R59 YRC TIME CONSTANT ADJUST
jt RIBBON CONNECTOR
Display Monitor PCB Testpoint and Adjustment Layout U3 ANALOG SWITCH MI TRIPLER
BRIGHTNESS CONTROL FOCUS CONTROL
HV. TRANSFORMER
X ANDY REGISTERS
ALU'S
U3 HIGH EVEN
JUMPER u7
DIP LOW EVEN ) 2 £3 (L.V. POWER)
(TO DISPLAY PCB) + GAME OPTION D2 TPL XTAL DIP PULL-UP
HIGH ODD _\ R7
LOW ODD P7 J CLKA 2O0MHZ J4 SWITCH J3 OP Ql Q2
RAM PROM WORKING — 120-05 STORAGE MEMORY (12x256)
Logie PCB PROM PROM 119-01 120-02
Testpoint and Adjustment Layout c2 PULL-UP DIP 30.
31.
POWER IN - THE POWER SUPPLY OPERATES AT 100, 115 OR 230 VOLTS 50 - 60 Hz., AS DETERMINED BY JUMPERS ON THE TRANSFORMER (SEE JUMPER SCHEDULE ON POWER SUPPLY)
AC HOT AC COMMON
EARTH GROUND
LAMPS - TWO 115 VOLT AC LINES, BLACK AND WHITE TWISTED PAIRS ARE PROVIDED FOR AT 115 VOLTS AC
THE POWER SUPPLY TO POWER LAMPS IN THE CABINET. THE AVAILABLE VOLTAGE 115 VOLTS IS INDEPENDENT OF THE SUPPLY INPUT VOLTAGE. WHEN OPERATING AT 230 VOLTS 230 VOLTS IS AVAILABLE BETWEEN PINS 12 AND 13.
115 VOLTS AC
POWER SUPPLY PIN DIAGRAM
fo} fo}
DISPLAY SHIELD - TO PREVENT DISTORTION IN THE DISPLAY
OBJECTS DISPLAYED ON THE MONITOR SCREEN IT IS NECESSARY TO PLACE AN ALUMINUM SHIELD UNDER THE DISPLAY UNIT. SIZE: 1735 "x8& "x .02" ( 44.5 on x 21.5 an x .05 ca)
aco f Iu O DISPLAY SHIELD:
TRANSTENT SUPPRESSOR
COIN COUNTER - USE A 24 VOLT DC COUNTER. A TRANSIENT __ RED SUPPRESSOR DIODE .{ 1N4003.OR EQUIVALENT ) MUST BE CONNECTED ACROSS THE INPUT TO THE COUNTER. com WHITE
SPEAKER - USE AN 8 OHM, 20 WATT, 8 INCH SPEAKER. THE SPEAKER MUST HAVE A GOOD -LOW FREQUENCY RESPONSE.
COIN SWITCH - A SPDT 5wifCH MUST BE USED TO SENSE THE COINS. BLUE N.C
BLACK COM
(OM GREY 2 9 N.O. N.O.
- JMMON : N.C. - NORMALLY CLOSED
N.O. - NORMALLY OPEN A COIN SLOT CONFIGURATION
BLUE N.C. BLACK —_| OM 9 N.O.
SINGLE COIN SLOT CONFIGURATION
INTERCONNECT DIAGRAM 33 TO COIN SWITCH ~
: DISPLAY :
CONTROL PANEL
DISPLAY SAFETY, GROUND
POWER AC POWER IN
115 VOLTS AC TO LIGHTS
TO COIN COUNTER LOGIC .
Cl 10 SPEAKER
- CAUTION WARNING - IMPORTANT ---- CONNECT DISPLAY SAFETY GROUND BEFORE
CONNECTING OR DISCONNECTING POWER SUPPLY
OR LOGIC BOARD -TO OR FROM THE DISPLAY UNIT
DO NOT CONNECT OR DISCONNECT ANY RIBBON CABLES OR POWER CONNECTORS WITH THE AC POWER APPLIED
HEATSING oun
ans
kare LONG, BInoING HEAD MACHINE SCREW prin #- PLACES
MICA WASHER 2- PLACES. USE THERMAL GREASE forM stoes
oT T~ASSEMBLIES REQUIRED D6 H0r09 9 WITH HARNFSSAY 10315 V1 SE 1UIE ES Worm Wau E Ss HARNESS 8? 10315 07
BENOLUG TOCLEAR HEATSINK
Heat Sink Assembly WIRE HARNESS. SEE NOTE —— —>
i 34.
40-10268 YOKE, BROY #746
TIE-WRAP
= °
a ir) >
3045
41-10228 MOLEX #03-09-1063
35-10225 MALE PIN, MOLEX #02-09-2118 ~- 35-10224 FEMALE PIN, MOLEX #02-09-1118
Yoke Assembly
Yoke Assembly Parts List 38-10344-01 Rev. A
PART NUMBER DESCRIPTION
35-10224-01 Pin, Female, Molex 02-09-1118 35-10225-01 Pin, Male, Molex 02-09-2118 40-10268-01 Yoke, Broy 746 41-10228-01 Con, Molex 03-09-1063, 6 Pin Recept
= i Zz < = [s) Ty = z
° °
COIN DOOR
Coin Mechanism Assembly
20-10293-01 21-10269-02 21-10420-01 25-10449-01 25-10450-01 71-10109-01 ITEM PART NUMBER DESCRIPTION Speaker Assembly Parts List 38-01422-01 Rev. A
Fab Speaker grill Fab gasket, speaker 9 1/4'"x9 1/4” Fab gasket speaker 8” (round)x 1/4” Xxx pop rivet 4AD410ABS xxx rivet washer flat #SBUP 1/8 xxx speaker Becker 908A237
Coin Meter Assembly Parts List 38-10008-01
ITEM PARTNUMBER DESCRIPTION
29-10218-01 35-10224-01 41-10219-01 65-10027-01 xxx coin meter E607B-100C24 pin pin, female, Molex 02-09-1118 con con, Molex 03-09-2038, 3 pin plug DiOrectifier, 1 amp, 1N4003
Coin Door Assembly Parts List 3810008-01
ITEM PART NUMBER DESCRIPTION
20-10338-01 25-10227-01 25-10270-02 25-10406-01 25-10407-01 25-10411-01 25-10437-01 26-10448-01 87-10342-01 1. 2. 3. 4. 5. 6.
8. 9. Fab coin door xxx cable tie, nylon 4 In. xxx ock, coin door fort #N5078AR403KD wsh #10 flat washer plated zinc wsh #10 lock washer plated zinc nut hex nut 10-24 plated zinc xxx tie mount TM 3525 (PANDUIT) xxx coin accecptor, #2608-3000-5 with front plate asy harness, coin door
Heat Sink Assembly (Front) Parts List . 38-10006-01 Rev. B
PART NUMBER DESCRIPTION
09-10337-01 Heatsink Compound, Wakefield #120 20-10229-01 Heatsink (2107) 25-10336-01 Screw, Mach, #6-32 x V2 Binding Hd. 66-10018-01 Transistor, PNP 2N5876 66-10019-01 Trnasistor, NPN 2N5878 87-10315-01 Harness Assembly, Front (for heatsink)
Heat Sink Assembly (Rear) Parts List 38-10006-01 Rev. B
{_ (TEM | PARTNUMBER DESCRIPTION
| 1 | 09-10337-01 | Heatsink Compound, Wakefield #120 |
| 2 | 20-10229-01 | Heatsink (2107) |
| 3 | 25-10336-01 | Screw, Mach. #6-32 x 2 Binding Hd. |
| 4 | 66-10018-01 | Transistor, PNP 2N5876 |
| 5 | 66-10019-01 | Transistor, NPN 2N5878 |
| 6 | 87-10315-02 | Harness Assembly, Rear (for Heatsink) |
38.
Display Assembly Parts List 38-10003-01
PART NUMBER DESCRIPTION 20-10256-01 Chassis, Display 20-10260-01 High Voltage Cage (2105A) 20-10261-01 Tube Mounting Bracket, L.H. (2169) 20-10262-01 Tube Mounting Bracket, R.H. (2170) 22-10233-01 Lable, ‘Do Not Operate Warning’ (2134) 22-10251-01 Lable, ‘High Voltage’ (2136) 22-10252-01 Lable, ‘Factory Adjustment Only’ (2137) 25-10187-01 Nut, Hex #6-32 25-10203-01 Screw, Sheet Metal #6 x 3/8 Hex, Type B 25-10206-01 Screw, Sheet Metal #10 x Ve Hex, Type A 25-10209-01 Lockwasher, Internal #6 25-10263-01 Washer, Flat #10 25-10264-01 Washer, Fender 3/16 Medium Wide, 1 IN. O.D. 25-10265-01 Spring, Century Spring #171C 25-10341-01 Washer, Flat #6 3/8” O.D. Waldom #MW-402 25-10343-01 Screw, Machine, 6-32 x 3/8, PH PH 38-10006-01 Heatsink Assembly - Front 38-10006-02 Heatsink Assembly - Rear 38-10007-01 2 Display Board Assembly 38-10344-01 Yoke Assembly 90-10266-01 Lube, Cathode Ray 19” 19-VARP4
Logic PCB Assembly Parts List 38-10001-01 Rev. F 40.
ITEM PART NUMBER DESCRIPTION
| 1 | 35-10179-01 | Test Points | |
| 2 | 36-10175-01 | Socket, 16 PIN 1.C. DIP | |
| 3 | 36-10176-01 | Socket, Amp 16 Jumper | |
| 4 | 36-10395-01 | Socket, 24 PIN | |
| 5 | 37-10178-01 | Switch, 2 Pole Dip | |
| 6 | 41-10150-01 | Con, Molex 09-18-5127, 12 PIN PC, F4 | |
| 7 | 41-10161-01 | Con, 34 PIN, 3M#3431-2202 | |
| 8 | 41-10162-01 | Con, 16 PIN, 3M#3408-2202 | |
| 9 | 41-10163-01 | Con, 26 PIN, 3M#3429-2202 | |
| 10 | 44-01001-01 | IC, ROM (1001) | |
| 1 | 44-01002-01 | IC, ROM (1002) | |
| 12 | 44-10110-01 | IC, 74800 | |
| 13 | 44-10111-01 | IC, 74802 | |
| 14 | 44-10112-01 | IC, 74804 | |
| 15 | 44-10113-01 | IC, 74508 | |
| 16 | 44-10114-01 | IC, 74810 | |
| 17 | 44-10115-01 | IC, 74832 | |
| 18 | 44-10116-01 | IC, 748113 | |
| 19 | 44-10117-01 | IC, 748158 | |
| 20 | 44-10118-01 | IC, 748182 | |
| 21 | 44-10119-01 | IC, 745288 | PROM, DROM, 1 |
| 22 | 44-10120-01 | IC, 745288 PROM, DROM, 2 | |
| 23 | 44-10120-02 | IC, 745288 PROM, DROM, 3 | |
| 24 | 44-10120-03 | IC, 748288 PROM, DROM, 4 | |
| 25 | 44-10120-04 | IC, 748288 PROM, DROM, 5 | |
| 26 | 44-10120-05 | IC, 745288 PROM, DROM, 6 | |
| 27 | 44-10121-01 | IC, 74LS00 | |
| 28 | 44-10122-01 | IC, 74LS02 | |
| 29 | 44-10123-01 | IC, 74LS04 | |
| 30 | 44-10124-01 | iC, 74LS08 | |
| 31 | 44-10125-01 | IC, 74LS10 | |
| 32 | 44-10126-01 | IC, 74LS27 | |
| 33 | 44-10127-01 | IC, 74LS32 | |
| 34 | 44-10128-01 | IC, 74LS75 | |
| 35 | 44-10129-01 | IC, 74LS85 | |
| 36 | 44-10130-01 | IC, 74LS86 | |
| 37 | 44-10131-01 | IC, 74LS107 | |
| 38 | 44-10132-01 | IC, 74LS151 | |
| 39 | 44-10133-01 | IC, 74LS157 | |
| 40 | 44-10134-01 | IC, 74LS163 | |
| 41 | 44-10135-01 | IC, 74LS164 | |
| 42 | 44-10136-01 | IC, 74LS194 | |
| 43 | 44-10137-01 | IC, 74LS259 | |
| 44 | 44-10138-01 | IC, 74LS298 |
Logic PCB Assembly Parts List 38-10001-01 Rex F
DESCRIPTION ITEM PART NUMBER
45 44-10139-01 46 44-10140-01 47 44-10141-01 48 44-10142-01 49 44-10144-01 50 44-10150-01 51 44-10340-01 52 53-10054-01 53 53-10058-01 54 53-10059.01 55 53-10062-01 56 53-10064-01 57 53-10066-01 58 53-10070-01 59 53-10072-01 60 53-10073-01 61 53-10080-01 62 53-10099-01 63 63-10030-01 63-10031-01 63-10040-01 63-10042-01 65-10026-01 65-10177-01 66-10011-01 66-10012-01 69-10214-01 80-01001-01 IC, 74LS377 IC, 74LS393 IC, 25LS818 IC, 2101A-2 IC, 7425 IC, 74265 IC, 74LS257 Res, CC, %W, 5% 100 OHM Res, CC, %W, 5% 330 OHM Res, CC, %W, 5% 470 OHM Res, CC, YW, 5% 1K Res, CC, “4W, 5% 2.2 K Res, CC, “WW, 5% 4.7K Res, CC, “W, 5% 10 K Res, CC, %W, 5% 20 K Res, CC, %W, 5% 30K Res, CC, %W, 5% 560 K Res, PACK, IK D-16-15-2-1K CAP, TANT, DIP, 25/35V, 3.3MF CAP, TANT, DIP, 35V, 33MF CAP, DISC, 50V, .O2MF CAP, DISC, 100V, 680PF DIODE, Si, SIGNAL 1N9148 LED, TIL220 TRANSISTOR, NPN 2N3904 TRANSISTOR, NPN 2N6292 CRYSTAL, 20 MHZ Logic Board 41.
42.
Display PCB Assembly Parts List 38-10007-01 Rev. H
ITEM PART NUMBER DESCRIPTION
| 1 | 20-10170-01 | Heatsink 6070B | |
| 2 | 20-10393-01 | Heatsink Wakefield 204AB | |
| 3 | 25-10187-01 | Nut, Hex #6-32 | |
| 4 | 25-10192-01 | Nut, Hex #4-40 | |
| 5 | 25-10195-01 | Screw, Mach. #4-40 x 3/8, PH PH | |
| 6 | 25-10208-01 | Lockwasher, STD. #4 | |
| 7 | 25-10209-01 | Lockwasher, International #6 | |
| 8 | 25-10336-01 | Screw, Mach. #6-32 x 2 Binding Hd. | |
| 9 | 36-10174-01 | Socket, CRT | . |
| 10 | 36-10175-01 | Socket, 16 Pin !.C. DIP | |
| 11 | 40-10173-01 | Tripler, Varo MH919 | |
| 12 | 41-10156-01 | Con, Molex 09-18-5960, 6 Pin PC, F3 | |
| 13 | 41-10157-01 | Con, Molex 09-18-5062, 6 Pin PC, F5 | |
| 14 | 41-10158-01 | Con, Molex 09-18-5069, 6 Pin PC, F1 | |
| 15 | 41-10161-01 | Con, 34 Pin, 3M #3431-2202 | |
| 16 | 43-10171-01 | Choke, 100 Microhenry | |
| 17 | 43-10172-01 | Transformer, High Voltage HV18 | |
| 18 | 44-10143-01 | IC, 7406 | |
| 19 | 44-10145-01 | IC, 7805 | |
| 20 | 44-10146-01 | IC, 7815 | |
| 21 | 44-10147-01 | IC, 7818 | |
| 22 | 44-10148-01 | IC, 7915 | |
| 23 | 44-10149-01 | IC, 7918 | |
| 24 | 44-10152-01 | IC, TLO81 | |
| 25 | 44-10154-01 | IC, DAC80 D/A Converter | |
| 26 | 44-10155-01 | IC, LF13331 Analog Switch | |
| 27 | 51-10105-01 | Pot, 10K A-B #JA1NO56S103UA | |
| 28 | §1-10106-01 | Pot, 1 Meg A-B #JA1NO56S105UA | |
| 29 | 51-10107-01 | Trimpot, 100 OHM Bourne 3352P1 | |
| 30 | 51-10108-01 | Trimpot, 5 K Bourne 3352P2 | |
| 31 | 53-10051-01 | Res, CC, “%W, 5% 15 OHM | |
| 32 | 53-10052-01 | Res, CC, “%W, Zi-CHM | |
| 33 | 53-10053-01 | Res, CC, “%W, 5% 47 OHM | |
| 34 | 53-10054-01 | Res, CC, %W, 5% 100 OHM | |
| 35 | 53-10057-01 | Res, CC, %W, 5% 200 OHM | |
| 36 | 53-10058-01 | Res, CC, “W, 5% 330 OHM | |
| 37 | 53-10059-01 | Res, CC, 4%W, 5% 470 OHM | |
| 38 | §3-10061-01 | Res, CC, “W, 5% 820 OHM | |
| 39 | §3-10062-01 | Res, CC, “ZW, 5% 1K | |
| 40 | §3-10063-01 | Res, CC, “W, 5% 1.8K | |
| 41 | 53-10064-01 | Res, CC, “W, 5% 2.2K | |
| 42 | 53-10065-01 | Res, CC, “W, 5% 3K | |
| 43 | 53-10066-01 | Res, CC, “W, 5% 4.7 K | |
| 44 | §3-10067-01 | Res, CC, “W, 5% 5.6 K | |
| 45 | 53-10070-01 | Res, CC, “W, 5% 10K | j |
Display PCB Assembly Parts List 38-10007-01 Rev HH
ITEM PART NUMBER DESCRIPTION
| 46 | 53-10076-01 | Res, CC, %W, 5% 68 K |
| 47 | 53-10083-01 | Res, CC, 2W, 5% 1.2K |
| 48 | §3-10084-01 | Res, CC, W, 5% 2.2K |
| 49 | 53-10085-01 | Res, CC, v2W, 5% 8.2 K |
| 50 | §3-10086-01 | Res, CC, %W, 5% 10K |
| 51 | 53-10087-01 | Res, CC, v2W, 5% 510 K |
| 52 | 53-10088-01 | Res, CC, 2W, 5% 4.7 MEG |
| 53 | 53-10089-01 | Res, CC, 1W, 5% 2.7 OHM |
| 54 | 53-10091-01 | Res, CC, 1W, 5% 360 OHM |
| 55 | §3-10092-01 | Res, CC, 1W, 5% 10 K |
| 56 | §3-10093-01 | Res, WW, 8W 150 OHM, OHMITE TYPE 200 |
| 57 | §3-10095-01 | Res, WW, 8W 500 OHM, OHMITE TYPE 200 |
| 58 | 53-10096-01 | Res, Metal Film, 1% 1.43 K, RN55D |
| 59 | 53-10097-01 | Res, Metal Film, 1% 2.1 K, RN55D |
| 60 | 53-10098-01 | Res, Metal Film, 1% 10 K, RNSSD |
| 61 | §3-10101-01 | Res, CC, %2W, 5% 47 OHM |
| 62 | §3-10102-01 | Res, CC, 2W, 5% 100 OHM |
| 63 | §3-10379-01 | Res, WW, 2W, 22 OHM DALE RS2B |
| 64 | 63-10029-01 | CAP, 50V, 50MF, Sprangue TE1307 |
| 65 | 63-10033-01 | CAP, TANT, DIP, 50V, 2.2MF |
| 66 | 63-10034-01 | CAP, TANT, DIP, 35V, 4.7MF |
| 67 | 63-10041-01 | CAP, DIST, 100V, .1MF |
| 68 | 63-10043-01 | CAP, 100V, SMF |
63-10044-01 CAP, ALUM, AXIAL LEAD, 100V, 10MF 63-10045-01 CAP, ALUM, AXIAL LEAD, 150V, 10MF 63-10048-01 CAP, Polycarbonate, 200V .022MF 63-10049-01 CAP, 250V, .068MF PLESSEY 63-10050-01 CAP, 100V, .1MF PLESSEY 63-10215-01 CAP, DISC, 100V, .OSMF 63-10380-01 CAP, TABULAR ,1MF 600V Sprague 6PS-P10 65-10024-01 Rectifier, FR MR818 65-10025-01 Diode, High Volt, MR250-2 65-10026-01 Diode, SI, SIGNAL 1N914B 65-10027-01 Rectifier, 1 AMP, 1N4003 66-10011-01 Transistor, NPN 2N3904 66-10013-01 Transistor, NPN 2N2102 66-10014-01 Transistor, NPN 2N5210 66-10015-01 Transistor, NPN 2N5320 66-10016-01 Transistor, PNP 2N5322 66-10017-01 Transistor, NPN 2N5550 66-10021-01 Transistor, PNP 2N3906 66-10023-01 Transistor, NPN TIP41C 80-02001-01 Display Board 87-10382-01 Ground Wire Assy - Display Board 43.
a DISPLAY BOARD.
MOLEX
103-09-1043 SURG Wuusreorain 122 BRN.
SPEAKER
TWISTED PA ters ye wH. Hov ac
auiony AUDIO BOARD
atone COIN METER
03-07-1038 ey mre
EMALE PIN. MOLEX 107-09-1118
$0” FEMALE DISCONNECT,
THOMAS B BETTS #A.250 HOLLINGSWORTH S0P600 ALL WIRE 105°C 200V,C.5.4.8 UL LISTED AWM. ain
Locic BOARD
be ow i x it +3 nb. WV AC
‘CABLE TIE 20 PLACES
Power Harness
Power Supply Schematic 45.
46,
MOLEX EDGE S| CONN Losic rec RIGHT Pe 18 eB 33 64
| { bWHT 2. | 7° | 2 + —vur | |
| 2 Leu \ | \\ | 4 Ltr | |
| 3 -RED A | | \o | B | Leer |
4 Lown - BS 3 — } -—Pewn
| 5S +-GRN- & | 4 \S | ; VS | STRIKE |
& -ERY-— K | -—— 26 —
i
es | LEST f ors
| \ WHT S|} | 7 | (2 [1 |
2 |-BLo- 10 fe \2 4 | RIGHT
| B -Reo- | -{ 18 | 3 | LEerT |
4 + BwWN- 7 -—— 16 —— | —
| S&S -orRn— 16 | 20 | 1S | —- STRIKE |
& }+BrK- 3 ee || /77 1
PIO | COIN AA
| 1 bore nN | 25 | = |
| 3 |-Bw.n7 P | 2A | \ |
epee Peer |
CONTROL INTERCONNECT DWI RGRAM
47.
me —t Om {" GTO srae
Monitor Display Electronics
Vector Display Electronics 48.
(PROCEED
ey ae
a raLesss
qa. tay Wega a
Tae
ans]
NO.
FRAME RATE? TE: G& OR HA TO BE INSTALLED, NOT BOTH: G6 FOR SO Hz FRAME RATE, H4 FOR 38 Hz
tanvany ATROME
: e
qousist sTRose
on TAL SSE Y qur
Gi MC mers) Cont raom ay
yom LIP Plone AME 7qLs107 1oK STROME
a roy
Tau
wevT func riems
Jha
covwran
aneaen
VECTORBEAM
LOGIC DIAGRAM so [eiioz7z (ETS
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
rover 4
jens « Pos Peeseen sn pesceer . se 2
ee PT ee Seserre ar
| , | 1 | a |
eeres qweseer
| aia | R4 | 2 | a |
- , a” i
WansoTr
RB
’ z At
| yerer | Ly | he |
- a
wie = 208 ame owe fat Beer one
uz 7 Zee zee
erates
Baa ar08
Pano & exon >
ae eo oO oy or om f sy k in fw P oe [os ra bey Ue! nln te le, evew oor
’ ref rue Neer pener Aeeeae seeees
reasary
% Fry
yaes37t
ada de ala dn dy 9 5. ..@/ 70273 sueer 3 or § Lhe
crrerr)
a
TAsIse8 cH
ay Hr-th03
ponon 2,
dD O.
Ip 2 oo Pal
cH Hm -T603
D.RONG Np py DRO
yee ecTeRNar. mon 4 ni Ape)
ree 2 of) or Xf)
Load rese ave Ps ()
Lea pees vectar 45>
wosnniite ow Tare evaay (4) ws) ar AY raat
Ae weere
& A se (a) x, meer) sere (D
re 2d bso (2) bere (4) wm)
aro (4,1) ess (2) race QA) Fare OY iome 4) (4) nucriaty (4) ino —aek C4)
m jX6 2D cane
be Ly nao
(_2cc 9 ex_sAce uly weer se (y_?he (pnawine 2 races wee
Fo yaesiss
eye 8
v smirreD (»-
VEereR LS)
(Ze
Beco wo
198N BI-1027Z SMELT ars cmpeeny, pot sete af
” bu aay —_t Taare as rnser Le, qaeenvaty a
at Eine th an
r00. . Lay, (Peony anal Seo Ly rm
ams Fees wt sz,
ares, te
neseryn Grows)
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Cg sep sy (WIDEBAND _ NOISE GENERATOR) 4] tox 2G? TSP soy rant Rr Be es
(PIT FALL),
A. LAST REF. DES. USED C43, RL3, D5, QT, IC19, Al 3. abo .ivf BrrASS CAP, (50V) FROM GHD.TO 45V FOK EACH
- 1C PACKAGES Using THE 457 SUPHY LINE, (C41, C42, 40435).
- ALL RESISTORS ARE IN OHMS, f4 Wi, 5% CARBON. 4 ALL CAPACITORS ARE IH MICROFARADS , 50¥, CERAMIC DISC. aa] SCHEMATIC AUDIO SOARD- WARRIOR or - -of
IT. 7) re ay ae J 4 54.
ETCH BOARD ‘w204200") ~
4 FILM CAP CAL ee suestirureo B NOTE CAMNTATION of OM {QA WW.
FoR CiA4,Ci5 a Cia.
- CA,CAt§ C43 ARE BYPASS ©. OA VSD WAVE MULTIPLE MOUNTING PADS CAPhCITORS. 7 INSTALL CAPROTORES RO BHOWN. Carrey
ALL CAPACITOR VALUES ARE IN MICROFARADS, 7. TC2,3,13,'6 PN @ ON TOS'R, PACUACE Dancree INO CERAMIC DISC, 40V. - AL Apion VALUES ARE IH OHMS, 4 W /UDIO BOARD - WARRIOR: RS 5% CARBON. : : f Gail aa, fea a a | more nets oTgninea srecinNo Loe sears Tar ‘B'| Be-cecse} Cc} al tong PSPS TET forage enonesel aii ioe wee Da SS Lh a 55.
56,