CATHODE RAY TOMES

Asteroids TM-143 4th Printing

Asteroids (rev 4) (Atari, 1979) · Technical Manual · 52 pages · 31 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

GAME SERIAL NUMBER LOCATION

Your game’s serial number is located on the outside rear of the game. The same number is also stamped on the chassis of the TV monitor, Game PCB and Regulator/Audio PCB. Please mention this number whenever calling your distributor for service.

GAME SERIAL # IDENTIFICATION TAG

TV MONITOR

REGULATOR/AUDIO PCB

GAME PCB

Page 3

Operation, Maintenance and Service Manual

Complete with Illustrated Parts Lists

Published by: ATARI INC. 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086

Copyright © 1979 by Atari, Inc. All rights reserved

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the torm of a phonographic recording, nor may it be stored in a retrieval system, transmitied, or otherwise copied for public or private use, without permission from the publisher.

Lithographed in the U.S.A. KS] A. ATARI

A Warner Communications Comoary

Page 4

Table of Contenis

1 Location Setup A. B. Game lnspection C. Game Installation... ..

  • Voltage Selection
  • Interlock and Power On/Off ‘Switches
  • Game Fuses D. Self-Test Procedure E. GamePlay .....
  • Attract Mode ...
  • Ready-to-Play Mode .
  • PlayMode ...........
  • High Score Initial Mode ..

2 Maintenance and Repair A. Cleaning B. Fuse Replacement...... C. Opening the Contro! Panel .

  • Leaf Switch Replacement.
  • LED Switch Replacement . TV Monitor Replacement....... Printed Circuit Board Replacement . Fluorescent Tube Replacement .. Game Operation ammo

3 Illustrated Parts Lists COMMDANKHAWWH=

Page 5

Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13

Figure 14 Figure 15 Figure 16 Figure 17 Figure 18 Figure 19 Figure 20 Figure 21 Figure 22 Figure 23 List of Illustrations

Overview of Game Installation Requirements . Power Supply ...........-- interlock and Power On/Off Switches ... . . Location of Self-Test Switch, Volume Control and Option Self-Test Procedure .... Option Switch Settings . Opening the Control Panel TV Monitor Removal Game and Regulator/Audio PCB Replacement Fluorescent Tube Replacement . Power Distribution ......... Signal Distribution .. 0.2.2... lee ee eee eee Mlustrated Parts Lists: Final Assembly Control Panel Assembly .... Asieroids Game PCB Assembly . Regulator/Audio PCB Assembly .. . Power Supply Assembly for X-Y Games . Main Harness and Component Assembly Fluorescent Light Assembly ........ Coin Door Assembly ... Front Bezel Assembly . New Coin Door

Page 6

Asteroids:

[NO If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographical area, as shown in one of the two maps below. Order all parts from the California office.

WEST and CENTRAL U.S.A.

Parts {or all Atari Customers. Sales and Service.

Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103 (Monday - Friday, 7:30 - 4:00 pm Pacific Time)

a from California, Alaska or Hawaii (408) 745-2900

eq From anywhere else in this area 2, toll-free (800) 538-1611

EAST U.S.A. Sales and Service Only

Atari Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, N) 08873 Telex 37-9347 (Monday - Friday, 8:30 - 5:00 pm Eastern time)

= From New Jersey (201) 469-5993

ae From anywhere else in this area toll-free (800) 526-3849

Page 7

Location Setup

A. New Parts

The Asteroids game has three new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: « Power Supply Assembly. It covers a wider voltage range than before, has higher reliability, a smaller overall size, and all fuse numbers and fuse amperages are marked directly on the metal chassis.

  • Game PCB Circuitry and TV Monitor. Most video games to date have used the raster scan method of display. This game uses vector generation with X and Y axes to allow greater contrast, a greater number of moving objects on the screen, and lines at any angle to be “‘drawn” on the screen.

Throughout this manual, wherever one of these three new parts is mentioned, you will see this symbol in the page margin: \

Page 8

ATTRACTION PANEL

TV MONITOR SHIELD

CONTROL PANEL

XYTV MONITOR

REGULATOR AUDIO PCB

COIN DOOR

GAME PCB

POWER SUPPLY

‘ACCESS POWER ON/OFF SWITCH PANEL

Figure 1 Overview of Game

Page 9

B. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.

NOTE Do not plug the game in yet!
  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: a. Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON’T FORCE CONNECTORS TOGETHER. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB. b. Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.

A WARNING

To avoid possible unpleasant electrical shock, do not touch internal parts of the TV monitor with your hands or metal objects held in your hands!

c. Note the location of the game’s serial number—it is on the metallic label on the back of the game cabinet. Verify that the serial numbers also stamped on the Game PCB, Regulator/Audio PCB and TV Monitor are all identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. d. Check all major subassemblies such as the power supply, control panel and TV monitor for secure mounting.

C. Game Installation

Figure 2 Installation Requirements

Power 175 watts Temperature 0 to 38° C (32 to 100°F) Humidity Not over 95% relative Space Required 65 x 79 cm (25% x 31 in.) Game Height 184 cm (72% in.)

«aD

Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per the list below.

  • Voltage Selection

Line Voltage Range Voltage Selection Plug Color

90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (220) Blue 220-260 VAC (240) Brown

  • Interlock and Power On/Off Switches

To minimize the hazard of electrical shock while working on the inside of the game cabinet, two interlock switches have been installed (see Figure 4). One is located behind the access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when a door is opened.

Check for proper operation of the interlock switches by performing the following steps:

  • Unlock and open the access panel and the coin door.
  • Plug the AC line power cord into an AC outlet.
  • Close the access panel and coin door.
Page 10

@

VOLTAGE SELECTION PLUG

SWITCH COVER

SAFETY INTERLOCK

POWER ON/OFF SWITCH

Figure 4 Interlock and Power On/Off Switches

Page 11

4, Set the power on/off switch to the on position. Within 30 seconds the TV monitor should display a picture.

  • Slowly open the rear access panel. The TV Monitor picture should disappear when the panel is opened approximately 2.5cm (1 inch). Close and lock the access panel and repeat this step with the coin door.
  • If the results of step 5 are satisfactory, the interlock switches are operating properly. If the TV Monitor doesn’t go off as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the on position.
  • Game Fuses

For continued protection of your game, as well as for the safety of the players, fuses must be replaced only with fuses with identical ratings. These ratings are shown in Figure 18. See the Schematic Drawing Package for fuse functions.

VOLUME CONTROL

SELF-TEST SWITCH Information on the TV monitor fuses is contained in the TV monitor manual that is supplied with this game.

D. Self-Test Procedure

This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the TV monitor and the game speaker, no additional equipment is necessary.

Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game's options.

To run the self-test, follow the instructions outlined in Figure 6.

OPTION SWITCHES

Figure 5 Location of Self-Test Switch, Volume Control and Option Switch

Page 12

Figure 6 Self-Test Procedure

RESULTS IF TEST

INSTRUCTION PASSES RESULTS IF TEST FAILS

1.Set self-testTV monitor displaysRAM FAILURE is indicated by a sequence of from 1 to 6 tones. A iow-frequency
switch to on posi-picture as shown intone is heard for each good RAM chip. A much lower frequency is heard for a
tion (see Figure 5).Figure 7.failing RAM chip. The sequence stops with the last failing RAM chip. To restart

the sequence, press the Reset pushbutton on the game PCB or set the self-test switch to off, then again to the on position. \dentify the bad RAM chip with table below. Example: Three tones, then a tone of much lower frequency indicates failure of RAM chip Ré.

TONE # RAM CHIP LOCATION OMRON D>

ROMI/PROM FAILURE is indicated by two columns or lines of numbers in the upper left-hand corner of the display. The number in the left column or first line indicates the failing ROM/PROM chipjs). Identify the bad ROM/PROM with table below. The number in the right column or second line indicates the failing data bit of the failing ROM/PROM. Identify the bad bit with the second table below. If more than one bit is failing, the displayed number(s) are hexadecimal combinations of the numbers shown below. Examples:

  • If bits D2 and D3 fail, C is displayed.
  • If bits D2, D3 and D7 fail, 8C is displayed.
  • If bits D4 and Dé fail, 30 is displayed.
  • If bits D1, D3, D5 and D6 fail, 6A is displayed

DISPLAYED NO. FAILING ROMIPROM

:NIPSK4,L4

2 F2, H1

3FAF2,L1eu

4 H2, J1

4DEIHa, J1Natu

6 J2, Kt

$lorK1, J2NOM

DISPLAYED NO. FAILING BIT 7 DO 2 ot 4 D2 8 D3 40 Ds 20 Ds 40 06 80 D7 RAMSEL SIGNAL FAILURE is indicated by a BANK ERROR or PAGE SELECT ERROR message at lower middle of display.

2.Activate all1 PLAYER START1 PLAYER START and/or 2 PLAYER START LEDs not lighted.

control panel and and 2 PLAYER

coin door switches.START LEDs areHigh-pitched click sound is not heard for any particular switch.

When satisfied with lighted. Hightest, set seif-test pitched click for switch to off posi- each activated tion. switch.

Page 13

Figure 7 Option Switch Settings To change toggle positions of the switch assembly, you need not remove the game PCB. The switch, usuaily colored blue, is easily accessible when the game PCB is When changing the options, verify proper results on the TV monitor display during self-test. A switch toggle in the on position is indicated by a 0 for that switch on the TV monitor display. A switch in the off position is indicated by mounted in place. the number 1.

Toggle Settings of & Toggle Switch on Game PCB Option

87654324
OnOnEnglishCTR. COIN MECH
ofOff‘Spanish

On 4Ship Game ofr 3Ship Game On Center Coin Mech x 1 ofr Genter Goin Mech x 2 (Both settings are for left ‘mech, it a 2-mech door)

OnOnRight Goin Mech x 1
OnOffRight Coin Mech x 4
OffOnRight Coin Mech x 5
OffoftRight Coin Mech x 6
OnOnFree Play

sks

onoft2 Goins or t PlayrmtFon aad wager? ond St

Suggested settings are shown in illustration at right.

  • Note: In the U.S. and Germany only, a “coin” is defined as 25¢ or 1 DM. If your game also has $1, 2 DM or 5 DM mechanisms, you must set the center and right coin mechanism factors as per your choice.

Toggle Settings of 4-Toggle Switch on Game PCB

4321For Games Having These Coin Doors:Option
OnOnThai 1 Baht/1 Baht, German 1 DM/1 DM, U.S. 25¢/25¢,All 3 coin mechanisms are

Belgian or French 5 Fr/5 Fr, Swiss or French 1Fr/1 Fr, same denomination; all U.S. 25¢/25%/25¢, Japanese Y100/¥100, Swedish 1 Kr/1_ register on one coin Kr, U.K. 10 P/10 P, Australian 20¢/20¢, or Italian 100 counter. W100 L

OffOnGerman 2 DM/1 DM, German 1 DM/5 DM, U.S.Left and center mechanisms

25¢/25¢/$1, or U.S. 25¢/$1 are same denomination; right mech is another denomination. Requires two coin counters.

OnOffNo coin door is currently designed for this configura-Left mech is one denomina-

tion. tion; center and right mech are another denomination. Requires two coin counters.

OffOffGerman 1 DM/2 DM/5 DMLeft, center and right mechs

are 3 different denominations. Requires three coin counters.

Page 14

E. Game Play

Atari's Asteroids game has five possible modes of operation: Attract, Ready-to-Play, Play, High Score Initial, and Self-Test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, ail game credits are cancelled.

  • Attract Mode

The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a coin is inserted and accepted or when in self-test. In this mode, the TV monitor displays two possible pictures. Both pictures have three score values across the top of the screen and a message that states the number of coins for a game. The middle score represents the high score to date. The left score is for player 1. The right score is for player 2.

One picture displays asteroids and an occasional enemy spaceship “floating” across the screen. The second picture displays up to 10 of the highest scores since the game was last powered up or since the last self-test. These two displays alternate every 16 seconds.

  • Ready-to-Play Mode

This mode begins when sufficient coins have been accepted for a one- or two-player game. It ends when the 1 PLAYER START or 2 PLAYER START pushbutton is pressed. When this mode begins, the message PUSH START flashes immediately below the center score at the top of the screen. The displayed pictures are otherwise the same as those shown in the attract mode.

  • Play Mode

The play mode begins when either start pushbutton is pressed. The made ends when the players last ship of the game is lost.

\f the 1 PLAYER START pushbutton is pressed, the following picture is displayed: the PLAYER 2's score disappears; the PLAYER 1's score becomes 00, and the number of ships (3 or 4, depending on the operator's setting) for the game appears below that score. The message PLAYER 7 also appears below the high score to date. Two seconds after pressing the 1 PLAYER START button the PLAYER 7 message disappears, and the game ship appears at the center of the display. Four large asteroids appear and drift in from the outer edges of the display.

If the 2 PLAYER START pushbutton is pressed, the following picture is disp!ayed: the PLAYER 1 and PLAYER 2 scores become 00, and the number of ships for the game appears below each score. The player 1 score also flashes as the message PLAYER 1 appears below the high score to date. Two seconds after the 2 PLAYER START pushbutton is pressed, the PLAYER 1 message disappears. The game ship for player 1 appears at the center of the display as four large asteroids appear and drift in from the outer edges of the display.

By pressing the LEFT ROTATE and RIGHT ROTATE pushbuttons on the control panel, the player may aim a spaceship toward any of the asteroids. By pressing the FIRE pushbutton, the player may shoot at the asteroids.

When shot, each large asteroid divides into two medium-sized asteroids and the game adds twenty points to the player's score. Medium-sized asteroids, when shot, divide into two small-sized asteroids, and the player receives fifty points. Smallsized asteroids, when shot, will completely disappear, and the game awards 100 points to the player. When players have shot all asteroids, a new set of large asteroids again appear and drift in from the outer edges of the TV monitor display. At the beginning of the game, four large asteroids appear. At the beginning of the next cycle when large asteroids reappear, there are six, the next time eight, and thereafter ten—io increase player challenge.

At any time during game play, a flying saucer may appear from either side of the display. The game awards players 200 points for shooting a large saucer and 1000 points for asmail saucer. (The latter is a smaller target for players, though not any faster moving than the large one. It also shoots more accurately.)

The player's objective in the game is to shoot and destroy as many asteroids as possible before all his or her spaceships are destroyed. A ship is destroyed if an asteroid or saucer Smashes into it, or if a flying saucer shoots it. To prevent losing a ship, the player may press the THRUST pushbutton to move out of the path of an asteroid or saucer. As an emergency maneuver, players can press the HYPERSPACE pushbutton: the ship disappears and reappears at a random location on the display—however, possibly tight on top of, or in the path of, an asteroid. The ship may also explode on reentry.

Page 15

The game awards an extra ship each time a player's score reaches multiples of 10,000; i.e., one ship is awarded at 10,000 points, another ship at 20,000 points, etc.

When the last ship of the game is destroyed, the message GAME OVER appears below the high score. This message remains for 3 seconds before the high score initial mode begins.

  • High Score Initial Mode

At the beginning of the high score initial mode, the player instructions appear at the top of the screen, and A__ _ appears ai the lower center of the display. Players enter initials one character at a time. By pressing the LEFT ROTATE pushbutton, the displayed character steps through the alphabet from A to Z. By pressing the RIGHT ROTATE pushbutton, the character steps backwards through ihe alphabet from A to a b/ank, then from Z to A.

Once the game displays the desired letter, players should press the HYPERSPACE pushbutton to record the letter; then an A appears in the next space.

If players need only two letters for their initials, they should use the b/ank between Zand A in one of the three locations. Pressing the HYPERSPACE pushbutton a third time will cause the initials and game score to be transferred to the “10 highest scores” listing that appears during the attract mode.

Page 16

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 17

Maintenance and Repair

The Atari Asteroids game requires certain maintenance to keep it in good working order. Clean, properly maintained games attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if LED switches or leaf switches are broken or if LEDs have burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly clean the leaf switch contacts: for details see this chapter.

Page 18

a

A. Cleaning

The exterior of the game cabinet and the metai and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dust can scratch the surface and result in fogging the plastic.

B. Fuse Replacement

This game contains six fuses—all on the power supply assembly (not including the TV monitor fuses). Replace fuses only with the same type as listed in Figure 18 of this manual. See the Quadrascan TV monitor manual, TM-146, for the monitor fuse data.

C. Opening the Control Panel

Prior to repairing or replacing any switch on the control panel or prior to removing the TV monitor, unplug the game. Then open the coin door.

Reach through the opening and remove both sets of wing nuts, split lock washers, and flat washers, located on the underside of the control panel (see Figure 8). The two carriage bolts will rernain in the control panel.

Lift up on the control panel and tilt it towards you. Be sure that the acrylic TV monitor shield does not fall on you. The top edge of the contro! panel acts as aretainer strip for the shield: once the control panel is opened, the shield is free and could slide out under its own power.

  • Leaf Switch Replacement

All five of these leaf switches operate on 5 volts at a very low current. Therefore, pitting of these switches would be extremely rare. Probably the only reason that pitting would occur is in very highhumidity locations.

Don’t burnish the switches. Burnishing them removes their plating, thus increasing the corrosion of the contacts. The best method of cleaning the switch contacts is to wipe them with a non-abrasive surface. A business card works very well.

To replace any switch, remove both of its screws with a Phillips-head screwdriver—see Figure 8.

If the white button itself needs to be replaced, turn the stamped nut with a wrench in a counterciockwise direction, as seen from the inside of the control panel. The white ring on the outside of the control panel should not spin, due to its design.

  • LED Switch Replacement

The light-emitting diode (LED) switches on the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 8.

  • Remove the wires from the suspected switch.
  • Set multimeter to ohms scale. Set ohms scale to R x 1, then zero the meter.
  • Check contacts (push and release the switch button) for closed and open continuity.
  • If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.
Page 19

COMMON - LIGHT-EMITTING CONTACT DIODE (LE.D.) / CONTACTS

<NORMALLY OPEN (N.O.) CONTACT

NORMALLY CLOSED (N.C.) CONTACT

L.E.D SWITCH: TO REMOVE TURN COUNTERCLOCKWISE

To remove LED switch: @ Remove ail wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped nut on the outside of the control panel. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires.

NOTE

Adjust leaf switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the contacts provides a selfcleaning feature.

LEAF SWITCH

TURN NUT TO REMOVE WHITE BUTTON

Figure 8 Opening the Control Panel

Page 20

D. TV Monitor Replacement

A WARNING

High voltages may exist in any television unit, even with power disconnected. Use extreme

caution and do not touch electrical parts or the TV yoke area with your hands or with metal objects in your hands! If you drop the TV monitor and it breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any TV monitor.

\f you should need to remove the Quadrascan X-Y TV monitor, follow steps 1 thru 6 on this page. Refer also to Figure 9 below. Open the control panel as described in Section C, Opening the Control Panel. Be sure the game is unplugged from its wall outlet! Remove the acrylic TV monitor shield by sliding its lower edge out. Working up from the bottom side corners, carefully pry loose the two side flaps of the colorful 2-piece cardboard bezel. (A 4-inch strip of double-sided adhesive tape is centered behind both side flaps, flush with each edge.) Remove the bezel as a complete unit—do not remove the smaller part first. Open the rear access panel and unplug the TV monitor harness connectors—both are on the TV's printed circuit boards. Remove the four sets of carriage bolts, flat and split lock washers, and hex nuts that hold down the metal TV chassis. Carefully slide the TV monitor chassis out the front of the game.

Disassemble In the order Indicated

Figure 9 TV Monitor Removal

Page 21

E. Printed Circuit Board Replacement

You may wish to remove the game printed circuit board (PCB) or the Regulator/Audio PCB for service or inspection. To do this, refer to Figure 10 and proceed as follows:

1. Open the rear access panel. Locate the securing screws and fiber washers that hold down the PCB in its slots, and remove them. (The game PCB has two, the Regulator! Audio PGB has one set of this fastening hardware.) If you are removing the game board, first remove the two machine screws or tie wraps that fasten the edge connector to the game PCB. Then unplug the edge connector on the game PCB. If you are removing the Regulator/Audio PCB, simply disconnect the three small harness connectors on this board. Carefully slide either PCB straight out of its slots. Be careful not to twist the board, as this May loosen connections or components. Replace or repair as required. Reinstali the PCB, making sure that the connectors are properly plugged in. Note that they are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connector will probably damage your game and will void the warranty. Replace the securing screws and fiber washers in the PCB. Reinstall the fasteners used to secure the edge connectors to the PCB. Close and lock the rear access panel,

Check thai the operation of the game is correct and perform the self-test. This is especially important with any game when you replace a PCB. Normally the only adjustments on the Asteroids game are option switch changes (made on the 4-toggle and 8-toggie DIP switches). Unless you are qualified technician, do not turn any of the knobs near the game PCB’s edge connector. Also do not turn the small knobs on the Regulator/Audio PCB.

REGULATOR! AUDIO PCB

GAME PCB

Figure 10 Game and Regulator/Audio PCB Replacement

Page 22

Astercids

F. Fluorescent Tube Replacement

A WaRNING

If you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.

To replace the white fluorescent tube behind the graphics attraction panel, follow this procedure (see Figure 11).

  • Remove the three Alien-head screws at the top of the game. They secure the metal retainer for the silk-screened panel. Remove the retainer completely.
  • Tilt the top of the attraction panel towards you, then lift it up and out of the bottom retainer.
  • Remove the two grey clips from the fluorescent tube. Now turn the tube one quarter turn in either direction. Remove the tube and both orange clips.
  • Replace with a new tube. If you move games a lot from one location to another, you should reuse the orange and grey clips. They provide extra protection against vibration loosening the tube out of its fixture.
  • Close up the game by following these instructions in reverse order.

G. Game Operation

With this manual you received two large sheets that contain the wiring and schematic diagrams for the Asteroids game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. These diagrams include information that explains the funciions of the circuits and defines inputs and outputs.

Atari's Asteroids is a microprocessor-controlled game. The microprocessor is contained on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCB and output to the TV monitor, Regulator/Audio PCB and control panel.

The TV monitor is an X-Y monitor. Therefore, the monitor receives signals for the X, Y and Z axes. Since the location of the bear in the monitor is totally controlled by the X- and Y-axis outputs of the game PCB, the game PCB does not contain a standard sync circuit. The X- and Y-axis inputs to the monitor step in increments of 1024 steps for the X (horizontal) axis and 768 steps for the Y (vertical) axis. The Z axis merely controls the intensity of the beam.

The RegulatoriAudio PCB performs two funtions:

  • regulates the + 10.3 VDC from the power supply to +5 VDC, and 2) amplifies the audio output from the game PCB. The +5 VDC from the Regulator! Audio PCB provides most logic power to the game PCB. The audio output from the Regulator/Audio PCB directly drives the game speaker and is controlled by the volume contro! mounted inside the coin door.

The Power Supply is the source of all voltages. in the game. These voltages are protected by five fuses in the fuse block on the Power Supply chassis. The primary winding of the Power Supply transformer is protected by the cartridge-type fuse in the power supply chassis.

Figure 12 illustrates the distribution of power in this game. Figure 13 illustrates the distribution of signals.

Figure 11

Fluorescent Tube Replacement

Page 23

FLUORESCENT LAMP

TV MONITOR

\ | [J SJ SN REGULATOR/AUDIO PCB

‘GAME PCB +5¥0C

COIN DOOR

POWER INTERLOCK SWITCHES 120 VAC.

POWER SUPPLY

AC POWER CORD

b

Figure 12 Power Distribution

Page 24

% GAME SPEAKER

> —\-CS5 TV MONITOR NS ) RIAUDI CONTROL REGULATORIAUDIO PCB PANEL R> th an Amman PF SERearEre ARAMA 4 \a\~\=\5 \S\2. 5 Vy eee \ hE \o \O 8 = i ess Sa FE} ° Ep BR = ~/3/8 seg st | N | oS VOLUME CONTROL i F con Xx

a > suM COIN DOOR at? NN

geet GAME PCB

Figure 13 Signal Distribution

Page 25

illustrated Parts Lists

The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for your Atari Asteroids game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc. When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be {ess downtime and more profit from your game.

Page 26

Figure 14 Final Assembly A035050-xx J

Page 27

Figure 14 Final Assembly Parts List

itemPart No.Description
2A036053-01Control Panel Assembly—see Figure 15
3‘A035056-01Access Panel AssemblyrN)
4A034986-01Asteroids Game PCB Assembly (PROM version)—see Figure 16

OR A034986-02 Asteroids Game PCB Assembly (ROM version)—see Figure 16

5A034485-01Regulator/Audio PCB Assembly—see Figure 17
6A034561-02Power Supply Assembly for X-Y Games—see Figure 18
7A035158-01Main Harness and Component Assembly—see Figure 19

OR A035158-02 Main Harness and Component Assembly

8A034628-01Light and Speaker Harness Assembly
QA034841-01Strain Relief Power Cord (domestic)

OR A034863-01 Strain Relief Power Cord (German)

10A034752-01Fluorescent Light Assembly—see Figure 20
WA030268-01Coin Box Assembly (2 holes)

OR A021700-01 Coin Box Assembly (3 holes)

14A009083-xxCoin Door Assembly—see Figure 21

So “> 71-102201 New Coin Door (U.S. 25¢/25¢)—see Figure 23 71102204 New Coin Door (German 2DMHDM) 71-102206 New Coin Door (German 1DM/5DM) 71-102207 New Coin Door (Belgian 5Fr/5Fr) 71102208 New Coin Door (Swiss 1F1/1Fr) 71-102209 New Coin Door (Japanese 100Y/100Y) 71-102210 New Coin Door (U.K. 10P/10P) 71102211 New Cain Door (Australian 20%/20¢) 71-102212 New Coin Door (Italian 100L/100L) 71-103202 New Coin Door (U.S. 25¢/25%/25¢) 71-103203 New Coin Door (US. 25¢/25¢/$1) 71-103205 New Coin Door (German 10M/2DM/5DM)

15A035724-01Cardboard Bezel Assembly with Graphics
16034457-01Speaker Grille
17035051-01Acrylic Attraction Panel with Graphics
18036049-01TV Monitor Shield with Graphics
19034515-01Upper Retainer Strip
20034516-01Lower Retainer Strip
23TM-143Asteroids Technical Manual
24001638-01Control-Panel Mounting Bracket
27006870-01Coin Box Bracket
28007882-02Interlock Switch Cover
2007103-01On/Off Switch Cover
3178-240125” Beaded Nylon Tie Wrap
32034536-02Foam Vibration Damper for Game PCB
33A036319-01Coin Door Adapter Harness (only for A009083-xx coin door)
3448-0098” High-Fidelity Speaker
36035437-01Connector Mount for TV MonitoraS
5692-04219” X-Y Black-and-White TV Monitor
577507017Fiber Washer
6099-11006Lamp Socket Ciip (each clip includes 2 pieces)
6170-30418” 15-Watt Cool White Fluorescent Lamp
65T™M-146Manual for Quadrascan X-Y Monitor
66DP-143-01Asteroids Schematic Drawings (Sheet 1)
erDP-143.02Asteroids Schematic Drawings (Sheet 2)

ai

Page 28

Gr 2 aid \ \) 4

NOTICE TO ALL PERSONS RECEWING THIS DRAWING f CONMDENTAL ‘Reproduction Tobiaden without Te yy J Speciic written permission of Atari. Inc.” Sunnyvale, sv Fora" Fns arming Oni cancion sued. and Pe ether recep nat Possession thereal confers or anglers ring oF 8 ‘nformatton, show thereon, No any ig ao reproduce ils awn. any par J lormanutacture by vendors 0! Ata, Incor stat 2 ster ‘wnt or watten permission Hom the corporation

Figure 15 Control Panel Assembly A035053-01 D

itemPart No.Description
1035047-01Control Panel with Graphics
2035046-01Control Panel Support
3033127-01Molded Biack Switch Bushing
4001856-01Aluminum Switch Bushing
5A035798-01Pushbutton Assembly
699-080023Leat Switch
7021105-01Metal Header Plate for Leaf Switch
ah]A035159-01Control Harness Assembly
177507054Flat Nylon Washer
1860-06015Phenolic Switch Spacer, 3/8” Hole Spacing x .094” Thick
Page 29

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 30

use sos ic postion fo PERS

Board is permanently marked -01 or -02

’, located between rows 10 & 11 (-01 for PROM, -02 for ROM version). “NX WBE THIS LC. POSITION,

G Figure 16 Asteroids” Game PCB Assembly A034986-01 and -02

Page 31

Figure 16 Asteroids Game PCB Assembly Parts List

temPart No.Description(Reference Designations and Locations in Bold)
2100000-27027 Ohm, +5%, %4W Resistor(R72)
3100000-680,68 Ohm, +5%, %W Resistor (R71)
4100000-121120 Ohm, +5%, %W Resistor (R105, 109)
5100000-151150 Ohm, +5%, %W Resistor(R55)
6100000-331330 Ohm, +5%, %W Resistor(R30, 31, 115)
7100000-471470 Ohm, +5%, %W Resistor(R32, 87-99)
8100000-681680 Ohm, +5%, %4W Resistor(R57, 61)
9100000-1021K Ohm, +5%, YW Resistor(R27, 29, 53, 73, 85, 86, 132, 134)
10100000-271270 Ohm, +5%, %4W Resistor(R112-113)
1100000-1221.2K Ohm, +5%, ¥4W Resistor (R35, 100)
12100000-2222.2K Ohm, +5%, YW Resistor (R36, 75, 117, 123, 133, 141)
13100000-2722.7K Ohm, +5%, YW Resistor(R66)
14100000-3323.3K Ohm, +5%, %W Resistor (R56, 65, 74, 142)
16100000-3923.9K Ohm, +5%, %4W Resistor(R39, 64, 106-108)
16400000-4724.7K Ohm, +5%, YW Resistor (R37, 82, 102, 137, 140, 144)
17100000-5625.6K Ohm, +5%, YaW Resistor(R40, 62, 67)
18100000-6826.8K Ohm, +5%, VW Resistor (R49, 104, 128, 129)
20100000-10310K Ohm, +5%, %W Resistor(R9-26, 28, 33, 38, 54, 58-60, 63, 69, 70, 79, 80,

103, 110, 111, 116, 122, 130, 131, 135, 136, 138, 139)

21100000-12312K Ohm, +5%, %W Resistor (R43)
22100000-15315K Ohm, +5%, %4W Resistor(R68)
23100000-18318K Ohm, +5%, ‘4W Resistor (R51, 146)
24100000-22322K Ohm, +5%, %W Resistor(R1-8, 34, 41, 45, 50)
25100000-33333K Ohm, +5%, %W Resistor(RS:
26100000-47347K Ohm, +5%, %W Resistor (R42, 44, 48, 76, 78, 83, 114)
27100000-56356K Ohm, +5%, ¥4W Resistor (R145)
28100000-104100K Ohm, +5%, %4W Resistor(R46, 81, 84, 143)
29100000-224220K Ohm, +5%, %W Resistor (R47)
30100000-274270K Ohm, +5%, %W Resistor(R101)
33100000-39339K Ohm, +5%, vaW Resistor (R77)
3419-00710K Ohm, 8-Pin Resistor Network. Use with the LS170 only, item 120. (RP1, 2)
3519-31510310K Ohm Vertical PCB-Mounting Cermet Trimpot, Bournes Series

3352V-1-10K (R120, 126)

3921-101104-1 uf,10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C64, 67-69)
4021-101224.22 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C33)
al21-101473,047 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C46)
Ag24-250105,1.0 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C25, 70, 90, 92,

93)

4524250107100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C19)
4624-250477470 uf Aluminum Electrolytic Fixed Axia!-Lead 25V Capacitor (C86, 87)
4724-25022622 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C117)
4927-250102.001 uf Ceramic-Disc 25V Radial-Lead Capacitor (C56)
5027-250103,01 uf Ceramic-Disc 25V Radial-Lead Capacitor(C27, 32, 36, 40, 55, 58)
6129.088.1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-18, 20-23, 26, 28-31, 34, 37,

41-44, 49, 51-54, 57, 60, 61, 63, 65, 66, 71-85, 91, 94-96, 99-100, 103-104, 107-108, 111-142, 114-116, 120-123)

5328-10110010 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C97, 105)
5428-10168068 pt Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C102, 110)
5528-101101100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C89)
5628-101221220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C98, 106, 118-119)
5728-101271270 pi Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C59)
5828-101391390 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C88)
6129-0061.0 uf, + 10%, 35V Tantalum Capacitor(C24, 35, 47, 50, 62, 113)
6329-04610 uf, + 10%, 20V Tantalum Capacitor (C38, 39, 45, 48)
6565-1N100General Purpose Germanium Diode (CR14)
6631-1N91475V 1N914 Switching Diode (CR1-4, 6-8, 15)
Page 32

Figure 16 Asteroids Game PCB Assembly, continued Parts List

ItemPart No.Description(Reference Designations and Locations in Bold)
6731-1N400150V 1N4001 Silicon Rectifier Diode(CR9-12)
6831-1N756A8.2V, +5%, 1N756A Zener Diode (CR13, 14)
7133-2N3906,Type 2N3906 PNP Switching and Amplifying Transistor(Q1-5, 7, 10, 16-17)
7234-2N3643Type 2N3643 NPN Silicon Transistor (Q6)
7334-2N3904Type 2N3904 NPN 60V 1-Watt Transistor(Q8, 9)
7434-2N6044Type 2N6044 Darlington NPN Transistor (Q11-13)
7534-MPSA06SType MPSAO6S NPN 80V 500ma Transistor(Q14, 15)
7837-74LS00Type 74LS00 Integrated Circuit(N5, C6)
7937-T4LS02Type 74LS02 Integrated Circuit(06)
8037-7404Type 7404 Integrated Circuit(H10)
8137-74LS04Type 74LS04 Integrated Circuit (B5, L5)
8237-7406Type 7406 Integrated Circuit (N9)
8337-74LS08Type 74LS08 Integrated Circuit(E6, K6, R7, B8)
8437-74LS10Type 74LS10 Integrated Circuit(A8)
8537-74LS14Type 74LS14 Integrated Circuit(B6)
8637-74LS20Type 74LS20 Integrated Circuit(E5)
8737-74LS32Type 74LS32 Integrated Circuit (M5, N6, B9)
8837-74LS42Type 74LS42 Integrated Circuit(L6, E7, E8)
8937-74LS74Type 74LS74 Integrated Circuit(D4, A7, R8)
9137-74LS83Type 74LS83 Integrated Circuit (M6)
9237-74LS86Type 74LS86 Integrated Circuit (P5)
9337-7497Type 7497 Integrated Circuit (F8, H8, J8, K8)
9437-74LS109Type 74LS109 Integrated Circuit(A9)
95,37-74L8139Type 74LS139 Integrated Circuit(L3, E4)
9737-74LS157Type 74LS157 Integrated Circuit(F3, H3, J3, K3, F&, A10, B/C10, F/H10, C10,

D/E10, E10)

9837-74LS161Type 74LS161 Integrated Circuit(C5, P8, B7, C7, D7)
9937-74LS164Type 74LS164 Integrated Circuit (K9, P9, R9)
10137-74LS174Type 74LS174 Integrated Circuit(N7, P7, 08, N11, F10)
10237-74LS175Type 74LS175 Integrated Circuit(M7)
10437-74LS191Type 74LS191 integrated Circuit(K5, C9, D9, E9, F9, H3, J9)
10537-74LS193.Type 74LS193 Integrated Circuit(F5, H5, J5)
10637-74LS244Type 74LS244 Integrated Circuit(B82, C2)
10737-74L8245Type 74LS245 Integrated Circuit(R2, E3)

OR

10837-8304BType 8304B Integrated Circuit—substitute for item 107 (P2, E3)
11037-74LS251Type 74LS$251 Integrated Circuit(J10, L10)
11137-74LS253Type 74LS253 Integrated Circuit(P6)
11237-74LS259Type 74LS259 Integrated Circuit(M10)
11337-74LS273Type 74LS273 Integrated Circuit(F7, H7, J7, K7)
11437-74LS367Type 74LS367 Integrated Circuit(H6, J6)
11637-74LS393Type 74LS393 Integrated Circuit(B4, D5)
11737-74LS374Type 74LS374 Integrated Circuit(B10, D10)

OR

11837-74LS273Type 74LS$273 Integrated Circuit—substitute for item 117
11937-74LS670Type 74LS670 Integrated Circuit(F4, H4, J4)

OR

12037-74LS170Type 74LS170 Integrated Circuit—substitute for item 119
12137-9316Type 9316 Integrated Circuit(C4
122(37-LM324Type LM324 Integrated Circuit(L8, P11)
12437-555,Type 555 Timer Integrated Circuit(M8, N8, L9, R10)
125,37-566Type 566 Function Generator Integrated Circuit(P10)
12737-4016BType 4016B Integrated Circuit(M9, N10, R11, B12, D12)
12837-TLO82CPType TLO82CP Integrated Circuit(A12, C12)
12937-AD5610Type ADS561J Integrated Circuit(B11, D11)
130137108-001Operational Amplifier Integrated Circuit(B/C12, E12)
Page 33

Figure 16 Asteroids Game PCB Assembly, continued Parts List

ItemPart No.Description (Reference Designations and Locations in Bold)
13237-7805+5V Voltage Regulator (VR3)
43337-7812+12V Voltage Regulator (VR1)
13437-7815,+ 15V Voltage Regulator (VR4)
135,37-7915~ 15V Voltage Regulator (VR2)
13738-MV5053Type MV5053 Light-Emitting Diode (CRS)
13941-3003100 uH, +5%, Hot-Moided Plastic Fixed R.F. Choke(L1-L15)
14162.001SPST Pushbutton Switch (A6)
14266-118P1T8-Station Single-Throw, Dual-tnline-Package Bit Switch(R6)
14366-114P1T4Station Single-Throw, Dual-Inline-Package Bit Switch(M12)
14479-42C4040-Contact Medium-Insertion-Force Integrated Circuit Socket(C3)
14681-4302Nylon Snap-in Fastener
148020670-01Test Point
15090-10212.096 MHz, + .005%, Crystal(¥1)
15190-6013Microprocessor(C3)
15290-7033Random-Access Memory (D2, E2, M4, N4, P4, R4)
155034602-01Programmable Read-Only Memory(C8)
157035127-01Read-Only Memory (N/P3)

OR THE FOLLOWING TWO ITEMS:

189035129-01Programmable Read-Only Memory, MSB-——substitute for hali of item 157(K4)
15903513001Programmabie Read-Only Memory, LSB—substitute for half of item 157(L4)

For remaining memory components and their part numbers, See listing below.

Memory Components and Their Equivalents (Locations Shown in Bold)

-01 P.C. Boards Altemate -01 P.C. Boards -02 P.C. Boards (PROMs) (PROMs) (ROMs)

035131-01 J2 03515001 J2 03513201 N2 035143-01 C1 035137-01 K1 035153-01 Ki 035138-01 N41

035133-01 H2 03515101 H2 035134-01 M2

  • 035144-01 D/E1 035139-01 J1 035154-01 J1 03514001 M1

035135-01 F2 03515201 F2 035136-01 L2 035145-01 F141 035141-01 H1

035142-01 L1 035155-01 1

Page 34

ES)

= :

z z °Q

Figure 17 Regulator/Audio PCB Assembly A034485-01 D

Page 35

Figure 17 Regulator/Audio PCB Assembly Parts List

ItemPart No,Qty.Description (Ref. Designations in Bold)
2110000-01021 Ohm, + 5%, YW Resistor (R10, 19)
3110000-100210 Ohm, + 5%, %W Resistor(R11, 20)
4110000-330133 Ohm, + 5%, %W Resistor(R3)
5110000-1015100 Ohm, + 5%, YW Resistor (R4, 12, 17, 18, 22)
6110000-2711270 Ohm, + 5%, %4W Resistor(R1)
7110000-10211K Ohm, + 5%, YW Resistor(R2)
8110000-27212.7K Ohm, + 5%, %4W Resistor(R23)
9110000-75217.5K Ohm, + 5%, %W Resistor(R7)
10410000- 103210K Ohm, + 5%, %W Resistor (R13, 14)
1110000-39213.9K Ohm, + 5%, %W Resistor(R6)
13110001-2212220 Ohm, + 5%, ”2W Resistor(R9, 21)
1512-52P712.7 Ohm, + 5%, 1W Resistor (R5)
1619-100P10151.1.Ohm, + 3%, 7W Wirewound Resistor (R24)
719-31510211K Ohm Vertical PCB-Mounting Cermet Trimpot, Bournes Series 3352V-

1-1K (8)

2024-250106210 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C6, 15)
2224-2504773470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C1, 4,

12)

2324-2501083100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C9, 10,

13)

2527-2501032.01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, C14)
2627-2501042.1 uf Ceramic-Disc 25V Radial-Lead Capacitor(C3, C11)
2727-2502242.22 uf Ceramic-Disc 25V Radial-Lead Capacitor(C8, 17)
227-2501023.001 uf Ceramic-Disc 25V Radial-Lead Capacitor (C2, 7, 16)
3131-A14F250V 2.5A Miniature Axial-Lead High-Current Rectifier(CR1, CR4)
3231-1N40012SOV Silicon Rectifier 1N4001 Diode (CR2-3)
3433-TIP321PNP Power Transistor, Type TIP32(Q2)
35,34-2N30551NPN Silicon Transistor, Type 2N3055Q3)
3634-2N39042NPN Silicon Transistor, Type 2N3904(Q4, 6)
3837-LM30515V Linear Voltage Regulator (Q1)
3937-TOA2002A2Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit(Q5, 7)
4479-58008,19-Position Connector Receptacle(J7)
4579-5809216Position Connector Receptacle(J6)
4679-5805914-Position Connector Receptacle(J8)
4779-2023019Female PCB-Mounting Terminal
48034531-011Heat Sink
4972-1608C,4#632 x Ye” Cross-Recessed Pan-Head Corrosion-Resistant Steel

Machine Screw

5075-995167#6-32 Nut/Washer Assembly
5175-0567#6 Internal-Tooth Steel Lock Washer
52020670-016Test Point
5375-F608053#6-32 x Ve" Binder-Head Nylon Screw
5778-160081Thermally Conductive Compound for the 2N3055
58.78-160143Thermally Conductive Compound for TDA2002A and TIP32
6052-0032Tefion-Insulated Solder-Plated Solid Copper PCB-Mounting Jumper Wire

with .6” Centers

6152-0042Teflon-insulated Solder-Plated Solid Copper PCB-Mounting Jumper Wire

with .3” Centers

Page 36

TOP VIEW

  • aReo’e 6
NOTE: The four available voltage selection plugs are listed in Figure 14, Final Assembly.

BOTTOM VIEW

Figure 18 Power Supply Assembly for X-Y Games A034561-02 D

Page 37

Figure 18 Power Supply Assembly for X-Y Games yy.) Parts List

ItemPart No.Qty.Description
AA034955-011Power Supply Sub-Assembly, Rev. A, consisting of the following 17 items:
1034482-011Base for Power Supply Chassis
279-44110064Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post
379-320615-Position 3AG Fuse Block with 4" Quick-Disconnect Terminals
446-201700227-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse
546-201300233-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse
623-053126,000 uf 15V Electrolytic Capacitor
t78-70501SC12” Diameter Capacitor Mounting Bracket
879-1502100112-Circuit Single-Row Terminai Block
978-27081Nylon Type 6/6 Hole Bushing with 5/8” Inside Diameter x 55/64” Outside

Diameter x %” Thick

10A006555-011Rectifier Printed Circuit Board Assembly
Nn72-HA4804S3#8-32 x 4" Cross-Recessed Pan-Head Zinc-Plated Steel Thread-Rolling

Tri-Fluted “Taptite” Screw

4272-HA4812S1#8-32 x ¥%" Cross-Recessed Pan-Head Zinc-Plated Stee! Thread-Rolling

Tri-Fluted “Taptite” Screw

1372-1008F2#1032 x %" Cross-Recessed Pan-Head Zinc-Plated Steel Thread-Rolling

Tri-Fluted “Taptite” Screw

1472-HA4606S4#632 x 3/8” Cross-Recessed Pan-Head Zinc-Plated Steel Thread-Rolling

Tri-Fluted “Taptite” Screw

1575-010S2#10 Flat Plain SAE-Standard Zinc-Plated Steel Washer
1675-018S4#8 Flat Plain SAE-Standard Zinc-Plated Steel Washer
775-995181#8-32 NuvWasher Assembly
BA034630-011PFI Filter Assembly
cA034629-012A.C. Harness Assembly
DA034623-021Power Supply Harness Assembly (for X-Y Games), includes the

following item:

1842-71411Power Transformer
E034544-011Fuse Block Cover
F75-018S4#8 Flat Plain SAE-Standard Zinc-Plated Steel Washer
G75-995186#8-32 Nut/Washer Assembly
H72-HA4812S2#8-32 x 3/4” Cross-Recessed Pan-Head Zinc-Plated Steel Thread-Rolling

Tri-Fluted “Taptite” Screw

J4035674-01Voltage Block Assembly, Rev. A, consisting of the following 4 items:
Page 38

Figure 19 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction forbidden without the specific. written permission of Atari. Inc, Sunnyvale, GBitornia" tive aeawng is only conarvonall; issued, and Senter rece nox possession teteo!confersof transfers

se, no ight 19 Tepreduce ths Sraw.ng Is gr ‘antea fect matter hereoi uniess by wites agreement wun or watien permission irom the corporation

Main Harness and Component Assembly A035158-02 A

item Part No. Description

1A035157-01Main Harness Assembly
2A034631-01On/Off Switch Assembly
368-002Interlock Switch (2 per game)
4000268-02Interlock Switch Mounting Bracket

5 A030169-01 Volume Control/Test Switch/Bracket Assembly

Page 39

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL Reproduction” larbidgen without the

Figure 20 Fiuorescent Light Assembly A034752-01 A

itemPart No.Description
1A005493-01Fluorescent Light Harness
1393-113,18” Fluorescent Lamp Fixture with Starter
1479-561816Spring Connector Wire Nut for 16- to 18-Guage Wires
1578-2652Rubber Grommet with 5/8” Inside Diameter x 1 1/8” Outside Diameter x 5/16”

Thick—for 7/8” Diameter Sheet-Metal Holes

Page 40

NOTICE 70 ALL PERSONS RECEN CoM Reprocuction

Figure 21 Coin Door Assembly A006794-16 thru -28 K

Page 41

Figure 21 Coin Door Assembly Parts List

ItemPart No.Qty.Description
1A007637-16Front Bezel Assy.—Used only on -16 Coin Door Assy. (25¢)
A007637-17+Front Bezel Assy.—Used only on -17 Coin Door Assy. (5 Fr)
A007637-18°Front Bezel Assy.—Used only on -18 Coin Door Assy. (1 DM)
A007637-19vaFront Bezel Assy.—Used only on -19 Coin Door Assy. (1 Kr)
A007637-20BoFront Bezel Assy.—Used only on -20 Coin Door Assy. (100 Y)
A007637-218 aFront Bezel Assy.—Used only on -21 Coin Door Assy. (10 pence)
A007637-2253Front Bezet Assy.— Used only on -22 Coin Door Assy. (20¢

ag Australian)

A007637-23SecFront Bezel Assy.—Used only on -23 Coin Door Assy. (2 DM/1 DM)
A007637-24anFront Bezel Assy.—Used only on -24 Coin Door Assy. (1 Fr)
A007637-25=Front Bezei Assy.—Used only on -25 Coin Door Assy. (1 Baht)

A007637-26 Front Bezel Assy.—Used only on -26 Coin Door Assy. (1 OM/5 DM) A007637-27 Front Bezel Assy.—Used only on -27 Coin Door Assy. (100 Lire) A007637-28 Front Bezel Assy.—Used only on -28 Coin Door Assy. (25¢/U.S. $1 coin) For breakdown of Front Bezel Assy., see Figure 22

272-HA4608C3#6-32 x Y2" Cross-Recessed Pan-Head Cadmium-Plated Steel Tri-

Fluted Thread-Rolling Screw

3A030362-011Coin Lockout Assembly
4A030250-012Coin Switch Assembly
5A002465-011Coin Counter Assembly
6004320-011Coin Door Weldment
8004344-011Key Loop
Q004340-012Spring Return (used only on German DM coin doors)
10004337-012Bracket for Lock-Out Wires
sal004338-011Right-Hand Lock-Out Wire
12004336-011Left-Hand Lock-Out Wire
13004326-012Scavenger Button
15006904-012Spacer (used only on German DM coin doors)
16030257-011Lamp Socket
770-11-471NEMA #47 Incandescent Miniature Bayonet-Base Lamp
1873-30082Carbon Spring Steel External Retaining Ring, for 4” Diameter Shaft
2072-HA4604C2#6-32 x %" Cross-Recessed Pan-Head Cadmium-Plated Steet Tri-

Fluted Thread-Roiling Screw

275-9951613"#6-32 Steel Nut and Spring Washer Assembly

*Quantity of 15 is used on the German DM coin doors

22008629-012Spring
2371-21181Cam Lock, Hudson #CR73A045S,
2471-1225CUCoin Mechanism for American Quarter
71-1205FFtrCoin Mechanism for French 5-Francs Coin
71:1201MGisCoin Mechanism for German 1-Mark Coin
71-1201KS,ossCoin Mechanism for Swedish 1-Krona Coin
71-12100YJoonCoin Mechanism for Japanese 100-Yen Coin
71-1210PEBodCoin Mechanism for English 10-Pence Coin
71-1220CA25Coin Mechanism for Australian 20-Cent Coin
71-1202MGageCoin Mechanism for German 2-Mark Coin
71-1201FFagoCoin Mechanism for French 1-Franc Coin
71-12018T&Coin Mechanism for Thai 1-Baht Coin
71-1205MGaCoin Mechanism for German 5-Mark Coin

71-12100LI Coin Mechanism for Italian 100-Lire Coin 71-1201ADU Coin Mechanism for U.S. $1.00 Coin

25007753-011Anti-Probe Plate
26A007638-011Slam Switch Assembly
2775-036S4#6 Flat Plain SAE-Standard Zinc-Plated Stee! Washer
2873-30256Carbon Spring Steel External Retaining Ring, for 0.184’ Diameter

Shaft

3075-0561#6 Internal-Tooth Zinc-Plated Steel Lock Washer
32033368-011Lock Bracket
33033369-011Lock Arm
3403337 1-011Siam Switch Insulator
Page 42

Asteroids:

2PLCS 1 6 PLCS

Figure 22 Front Bezel Assembly © 2PLCS

A007637-16 thru -28 J Parts List

itemPart No.Qty.Description
1004328-024Bezel
2004330-02Ring for American Quarter
004330-024Ring for French §-Franc Coin
009153-02zRing for German 1-Deutschmark Coin
004330-02geRing tor Swedish 1-Krona Coin
009153-02ofRing for Japanese 100-Yen Coin
007752-02QFRing for English 10-Pence Coin
007752-02agaRing for Australian 20 Coin
030677-02rey .Ring for German 2-Deutschmark and U.S. $1.00 Coins
009153-02Q&Ring for French 1-Franc Coin
030677-02aRing for Thai 1-Baht Coin
007752-02|Ring for German 5-Deutschmark Coin

030677-02 Ring for Italian 100-Lire Coin

3004331-022Coin Shield
4004332-022Primary Coin Chute
5004327-012Scavenger Button Bearing
6004329-012Price Plate Clamp
7004343-01Price Plate--25¢
004343-064Price Plate—5 FR
004343-04SPrice Plate—1 DM
004343-03BePrice Plate—1 KR
004343-05maPrice Plate— ¥ 100
004343-028sPrice Plate—10 P
004343-07akPrice Plate—20¢ Australian
004343-08gePrice Plate—Einwurf 2 DMI1 DM
004343-09S&Price Plate—1 FR
7004343-10aPrice Plate—1 Baht

004343-11 Price Plate—Einwurf 1 DM/5 DM 004343-12 Price Plate— 100 Lire 004343-13 Price Plate—25¢/$1

873-30092Carbon Spring Stee! External Retaining Ring, for 3/8” Shaft Diameter
972-1604S3#6-32 x %" Cross-Recessed Pan-Head Cadmium-Plated Steel

Machine Screw

1075-0462#6 Corrosion-Resistant Steel Split Lock Washer
aul72-CL6066#6-32 x 3/8” Phillips Pan-Head Steel ‘Rolok’’ Self-Threading,

Thread-Roiling Machine Screw

1375-0564#6 Internal-Tooth Zinc-Plated Steel Lock Washer
Page 43

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 44

NOTICE TOALL PERSONS RECEIVING THIS DRAWING Torben 99-10095

99-10073

PART OF 99-10095

COIN INLET CHUTE 99-10097

99-10105

99-10081 COIN MECHANISM Gi SEE PARTS LIST (71-12xx%) / @ aa 75-9448 oo ra ( 99-10102 65-4416 / a 72-9603S COIN RETURN { 9910065 SWITCH WIRE . CHUTE 99-10068 J SEE PARTS LIST mS I = (99-10075 thru aeinadie 99-10078) ‘ COIN SWITCH ASSY. : 1 PART OF 99-1047 SEE PARTS LIST 99-1008 99-1082 (99-1002 thru 75-14128 99-1045)

Figure 23 New Coin Door 71-10.00

Page 45

COIN RETURN BUTTON ASSY SEE PARTS LIST (99-10012 thru 99-10022)

COIN DOOR ONLY SEE PARTS LIST (98-10009 thru 99-10010)

75-5520B

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproquction forbidden without the ‘Speciiic written permission of Alan. Ine. Sunnyvale Califor

subject matter of ine Grawing or any design or techacal information, shown, thereon, norany ngnttoreproduce this drawing or any part thereo!, except for manulacture by vendors o! Ala, Incor Doraied and lor manufaciuie under the corporation's wt fen ticanse, no right 1o reproduce this drawing 's grantect ‘or the subject matter theveot unless by whiten agreement ‘with or written permission from the corDoration a

75-915S

REJECT BUTTON COVER ys)

SEE PARTS LIST (99-10055 thru 99-10059) PRICE PLATE SEE PARTS LIST (99-10070, 99-10083 thru 99-10092) ee sara 72-JA1405B.

99-10054

72-HA1404C.

99-10061

72-JA1405B

99-10051

Figure 23 New Coin Door 71-10 xXXx

Page 46

Figure 23 New Coin Door, continued Parts List

Part No. Description

31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-441C General-usage low-force miniature switch 70-11-47 Miniature bayonet-base incandescent lamp, type #47 71-1201ADU U.S. $1.00 coin mechanism 71-1201FCH Swiss 1 Fr coin mechanism 71:1201MG German 1 DM coin mechanism 71-1202MG German 2 DM coin mechanism 71-1205FB Belgian 5 Fr coin mechanism. 71-1205MG German 5 DM coin mechanism 71-1210PE UK. 10 P coin mechanism 71-1220CA Australian 20¢ coin mechanism 71-1225CU U.S. 25¢ coin mechanism 74-12100LI {talian 100 Lire coin mechanism 71-12100YJ Japanese Y100 coin mechanism 72-HA1404C #4x%" Slotted pan-head thread-rolling tri-fluted “Taptite” cadmium-plated screw 72-JA1405B #4x5/16”" Slotted pan-head thread-rolling tri-fluted “Plastite” black screw 72-9406S #4-40x3/8” Slotted truss-head steel machine screw 72-9603S #6-32x3/16" Slotted truss-head steel machine screw 75-915S, #%-20 Standard pattern cadmium-plated steel hex nut 75-918S, #8-32 Standard pattern cadmium-plated steel hex nut 75-944S, #4-40 Polymer self-locking steel hex nut 75-948S, #8-32 Polymer self-locking steel hex nut 75-1408S #4-40x V2" Slotted pan-head steel machine screw 75-1412S #4-40x%4” Slotted pan-head steel machine screw 75-5520B #%-20x1%" Round-head square-neck steel bolt with black finish 99-10008 Switch wire retainer 99-10009 2-Mech coin door only 99-10010 3-Mech coin door only 99-10011 Inner panel 99-10012 U.S. 25¢ coin return button assembly 99-10013 U.S. $1.00 coin return button assembly 99-10014 German 1 DM coin return button assembly 99-10015 German 2 DM coin return button assembly 99-10016 German 5 OM coin return button assembly 99-10017 Belgian 5 Fr coin return button assembly 99-10018 Swiss 1 Fr coin return button assembiy 99-10019 Japanese Y100 coin return button assembly 99-10020 U.K. 10 P coin return button assembly 99-10021 Australian 20¢ coin return button assembly 99-10022 {talian 100 Lire coin return button assembly

Page 47

Figure 23 New Coin Door, continued Parts List

Part No. Description

99-10040 Coin inlet chute assembly 99-1004 Coin counter assembly 99-10042 Coin switch assembly for U.S. 25¢ and Belgian 5 Fr coins (silver wire) 99-10043. Coin switch assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 coins (black wire) 99-10044 Coin switch assembly for U.S. $1.00, German 2 DM, and Italian 100 Lire coins (gold wire) 99-10045 Coin switch assembly for German 5 DM, U.K. 10 P, and Australian 20¢ coins (green wire) 99-10047 Lockout coi! assembly 99-10048 Coin door harness assembly 99-10049 Locking arm assembly 99-10051 Coin door frame 99-10054 Coin button housing 99-10055, Coin return button cover for Japanese Y100 coin 99-10056 Coin return button cover for German 1 DM and Swiss 1 Fr coins 99-10057 Coin return button cover for U.S. 25¢ and Belgian 5 Fr coins 99-10058 Coin return button cover for U.S. $1.00, German 2 DM, and Italian 100 Lire coins 99-10059 Coin return button cover for German 5 DM, U.K. 10 P, and Australian 20¢ coins 99-10061 Coin return bezel 99- 10062 Coin return button 99-10063 Right half of coin inlet chute 99-10064 Left half of coin inlet chute 99-10065 Coin return box 99-10066 Coin return cover 99-10070 U.S. 25¢ price plate 99-10071 Slam switch assembly 99-10073 Test switch decal 99-10074 Lock assembly 99-10075 Biack switch wire—for German 1DM, Swiss 1Fr and Japanese Y100 coins 99-10076 Silver switch wire—for U.S. 25¢ and Belgian 5Fr coins 99-10077 Gold switch wire—for U.S. $1.00, German 2DM and Italian 100 Lire coins 99-10078 Green switch wire—for German 5DM, U.K. 10P and Australian 20¢ coins 99-10080 Miniature bayonet-base lamp socket 99-10081 Wire key holder 99-10082 Switch cover 99-10083 U.S. $1.00 price plate 99-10084 German 1 DM price plate 98-10085 German 2 DM price plate 99-10086 German 5 DM price plate 99-10087 Belgian 5 Fr price plate 99-10088 Swiss 1 Fr price plate

Page 48

Figure 23 New Coin Door, continued Parts List

Part No. Description

99-10089 Japanese Y100 price plate 99-10090 U.K. 10 P price plate 99-10091 Australian 20¢ price plate 99-10092 Italian 100 Lire price piate 99-10094 Fish paper insulation 99-10095 Toggie switch 99-10096, “U"-type fastener 99-10097 Fish paper insulation 99-10101 Coin inlet chute sub-assembly 99-10102 Switch and lockout coil bracket sub-assembly 99-10103 Inner panel with levers sub-assembly 99-10104 Anti-penny-flip bar retainer 99-10105 Anti-penny-flip bar

Page 49

ee TM-143 4th printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill m if you wish a reply:

Name Firm 1 Distributor C Operator Address _. (J) Other ___ —

City State Zip

Page 50

First fold

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if mailed in the United States

Second fold

98066 VO “ATVAANNNS:

Cut along this line

Page 51

REE EE EE ES

WARRANTY

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty

  • days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are « defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order. ESE AS ES SEES The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is perfomed by such distributor.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 52

ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 @SUNNYVALE, CALIFORNIA 94086 ATARI ee * TELEX 35-7488 A Warne