CATHODE RAY TOMES

Cruis'n USA Single Sitdown Preliminary (16-40036A-101 Aug 1994)

Cruis'n USA (v4.5) (Midway, 1994) · Manual · 45 pages · 26 sections · original scan

Page 1

MID WA Y August 1994

16-40036A-101

CRUIS’N USA

SINGLE SIT DOWN

PRELIMINARY MANUAL

Operations Manual Includes

  • Operations & Adjustments ¢ Testing & Problem Diagnosis
  • Parts Information
  • Reference Diagrams & Schematics

Midway Manufacturing Company 3401 North California Avenue Chicago, Illinois 60618

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

WARNINGS & NOTICES

Warning USE OF NON-MIDWAY PARTS OR CIRCUIT MODIFICATIONS MAY CAUSE SERIOUS INJURY OR EQUIPMENT DAMAGE! USE ONLY MIDWAY AUTHORIZED PARTS.
  • For safety and reliability, substitute parts and modifications are not recommended.
  • Substitute parts or modifications may void FCC type acceptance.
  • This game is protected by Federal Copyright, trademark and patent laws. Unauthorized modifications may be illegal under Federal law. This also applies to MIDWAY logos, designs, publications and assemblies. Moreover, facsimiles of MIDWAY equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with MIDWAY components.
Warning This equipment generates, uses and can emit radio frequency energy and, if not installed properly and used according to the directions in this manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of part 15 of FCC rules which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference to radio communications, in which the user, at his or her own expense, will be required to take whatever measures may be needed to correct the interference.
Warning Prevent shock hazard and assure proper game operation. Only plug this game into a properly grounded outlet. Do not use a cheater plug to defeat the power cord's grounding pin. Do not cut off the ground pin.

Notice When MIDWAY ships a game, it is in compliance with FCC regulations. Your sticker is proof. If the sticker is missing or damaged, legal repercussions to the owner or distributor of the game may result. If your game does not contain an FCC sticker, call MIDWAY immediately.

Notice No part of this publication may be reproduced by any mechanical , photographic, or electronic process, or in the form of a phonographic recording, nor may be transmitted, or otherwise copied for public or private use, without permission from the publisher.

For Service: Call your Authorized MIDWAY Distributor.

MIDWAY MANUFACTURING COMPANY 3401 N. CALIFORNIA AVE. CHICAGO, ILLINOIS 60618

Entire contents of this manual copyright © 1994 MIDWAY Manufacturing Company. All rights reserved.

Page 4

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 5

TABLE OF CONTENTS

Section 1 - Operation... cseseneeseeneeeeseeeseseneneeeceeeseeeneeseeeseeeeneeseneees 1-1 Safety Notices ..........cccecesecsssseseseeseseseenensesesneseseseeeseeesesesneneneeetsneneneretiensensaeesaenenseees 1-2 Set-Up Procedure...........cccccccccccecsscesscecseeescseceeseseneeeceseescsssesnesseeeestensnesseeneeaseeneeaenees 1-3

Location Requirements. .... Installation & Inspection

Servicing. Game Features.

Starting-Up Player Comtrols......cccecccessssesssssessesseeseseseseeseneseneneeneseseaeeeseseeeseeeeneneneesneeaeneneseee 1-7 Game Operation ........... cece cseseseseseneeceeenenseseseeeseaenseessssececseneeeenenenenseseneneeneeneeees 1-8 Cabinet SWitche 0.0... ccssecsesessesssceceesescssseessesesrseseesssssssssensasssesensesnessseeeeetacies 1-8 Control SWItCheS .....ccc ce cecscecsescsesstsesesseessessssesesesenscseseesesesessescseeacassesasecaeeaeess 1-8 Menu System Operation... ccc cesceseseeseeseseeeseseeseeesesseseseenesnenssnensanenessenenee 1-9 Operation oo... ccccccceeseesesesesesesesescsecsesesceccecseeeecsenecseseseaeesenseeeneneneesesenenseseseneeses 1-9 Main MEN u.....ecccecceesesescsssesesesesesessssesenssseseanscseseeecseeececseeseseseneeneesenenesseeneeas 1-9

Diagnostic Tests.........cccsessssecsesssesrsesteneneseseeeeeeeseesseseenenensteneiensesnenenneseeeneeeeeates 1-10 Switch Test... 1-10

DIP Switch Test 1-10

CPU Test 1-11

Sound Test - 1-11

Monitor Patterns... scaccccsvscecvotssoescacesnsivsnnarageveconstencssvensnesensseccearsetcasertonessonss 1-11 BUP-ifi T@St........... ee eect rseconsascasssonainitiniiin ain casesiacnigannniiensics, TAA Game AUIS oo... cece ces cseseeeseeceeeeesessecsesesececseseeeesesenecassesssssseseecseseneeeeseneeese 1-12

Game AdjUstMent...........ccscecesssssesseesesssseeseestsrenenerssssessasscesseesstesssstcssesesnseeees EOT4 Standard Pricing Table... eeeseseersesteesseeeseesteisesssstsesesteaeteteeeeers 116 CUstott Ping ics cces seers avanssssnevsesansvenscansescseavseuestecvesesonaness avenanerstatsriseeesenneseoseen, VOUT WUHHHROS ence senteesececerscserscerncopenoonerrrrste rishi sh atnaneieresnsiasennieniaiiatisesenesesces 118 Troubleshooting oo... ccc cceeseesee ee csesesesescecesescesssssesssessssesrereeesessesisssssssssseseerseeeeees E19 NOteS oo. eeesesessssescecescsescscecsterseseseeneecsssssssssnsssnessssseassasssssasasssssesecssssssassasisssssesessereseesesee 1°20

©Copyright 1994 MIDWAY Manufacturing Company

i

Page 6

Section 2 - Parts Information

Cabinet Hardware... reece Electronic Rack............ 2-2

Speakers... ese Transformer Assembly.

Dash Assembly.. Fluorescent Lamp AssembI:

MONO oe ececessscsccscesesesesceeeneneesesenscscseneversessesssesecsesesesessenseecsesesecaueseesaenesaeeeneeataeeacaeeensens

CADIOS ..ceseeceescesssssecsnscsssesecccceesnseersssssssssatocsesesencoeseaeseasenesscaessaesesenecsosonoaenesesserereeseeees Seat ASSeMbly .........cescescsseseesesceseseeeeseeeeneneeeeeensseseeeraneacarsissnsecsesessssseeesasesateetensessenines 2-2 Power Supply Switcher ASSEMDLy ..........cecceeseecteceeeeeeeeeeseeneeneseesnsensstessssssesneenseetenesnes 2-3 Wheel Driver Board ASSEMDIY ........:ceeesesesestereeeteeseseeeseeeenenenteeteneeeetsnensteneasesseeeseanes 2-4 CPU/Sound Boatrd .......ccsscseeseessecssorsesenenesnsestasetecsenesesesessansensnensserasesenessenensossoensieesnes 2-6

Dash ASSEMDIY .......c.csccseceessssessssenessensseeneneencaeeesseessatavesssrasesseassesesesiseensseseasaneasessetesenne® 2-11 Monitor Cover .....cccccssescscsesessescsessesccssnsceessesesesecsesecesseseseceeseseseaseneeeenenerseeensnasisaceseesneess 2-12

Section 3 - Schematics and Diagrams

JAMMA Chart.

Power Wiring Diagram Cabinet Wiring Diagram........cecccsecsceseseseeeesesecseearesesseenseanestensseseneseessssseseseasanesness 3-5

ii

Page 7

CRUIS’N USA

SINGLE SIT DOWN

Page 8

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 9

CRUIS’N USA

SINGLE SIT DOWN

SECTION

ONE

Operation

Page 10

Safety Notices

The following safety instructions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. We recommend that you read this page before preparing your game for play.

WNeaurioy

AC POWER CONNECTION. Before connecting the game to the AC power source, verify that the “line voltage selection chart" jumper wires are installed correctly for the line voltage in your area. For details, refer to Section 3.

PROPERLY GROUND THE GAME. To avoid electrical shocks, do not plug in the game until it has been inspected and properly grounded. MIDWAY games should only be plugged into a grounded 3-wire outlet. Shocks will also result, if the control panel is not properly grounded! After servicing any parts on the panel, be sure that the ground wires are secure. Only then should you lock up the game.

DISCONNECT POWER DURING REPAIRS. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game.

USE THE PROPER FUSE. To avoid electrical shock, use the replacement fuse which is specified in the parts list for this game. The replacement fuse must match the original fuse in fuse type, voltage rating, and current rating.

MONITOR PRECAUTIONS. When removing or repairing the monitor, extra precautions must be taken to avoid electrical shock. High voltages may exist within the monitor circuitry and cathode ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the monitor with your hands or metal objects! Always discharge the CRT by the following method: Attach one end of a large, well-insulated, 20-kv jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again.

HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.

ATTENTION! PROPERLY ATTACH ALL CONNECTORS. Make sure that the connectors on each printed circuit board (PCB) are properly connected. If the connectors do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. All connectors are keyed to fit specific pins on each board.

Bab

Page 11

Set-Up Procedure

Game Location Requirements Power: Domestic 115V @ 60 Hz Dimensions (assembled): — Width: 30" Foreign 230V @ 60 Hz Depth: 61" Temp.: 32°F to 100° F Height: 67" (0° C to 38° C) Humidity: Not to exceed 95% relative. Weight: Pedestal. 95 Lbs. Game 395 Lbs.

Installation And Inspection

  • Remove all items from shipping containers and set them aside. Inspect the exterior of the cabinet for any signs of damage. Remove shipping cleats from the bottom of the cabinet. Remove pedestal mounting rails packed inside seat liner.
  • Remove keys from the taped coin return slot. Unlock and open the coin and cash box doors. (Leg levelers and spare parts are stored in the cash box).
  • Tilt or lay the cabinet down. Locate two threaded holes on the bottom of the cabinet and install one leg leveler (with its hex nut) in each hole.
  • Stand cabinet upright and make certain it is in a stable position. Level the cabinet.
  • Leg levelers come installed on the pedestal assembly and need only to be leveled before installing onto the cabinet assembly.

Noxaner ease \ eens PDESTAL MOUNINE HOLES (F-MUTS)

  • Attach mounting rails to cabinet base using four 1/4-20 hex-head bolts (see above diagram for proper placement). Do not tighten bolts completely, some movement is required in the mounting rails to align holes with pedestal assembly.
  • Place pedestal assembly on mounting rails. Align the holes and carefully pull the pedestal away. Hold mounting rails in position and tighten bolts inside cabinet.
  • Connect speaker wire from inside pedestal to cabinet. Attach pedestal assembly and bolt together using eight 1/4-20 tamper proof screws. Use the T27 wrench (20-10140), included in the spare parts, to install these screws.

1-3

Page 12
  • Remove rear door of cabinet. Inspect cabinet interior for any signs of damage. Check all major assemblies to assure that they are mounted securely.
  • Refer to the games Cabinet Wiring Diagram (section 3), and check to see that all cable connectors are correctly secured. DO NOT FORCE CONNECTIONS. Watch for damaged connectors and avoid making reversed connections.
  • Determine the value of your line voltage with a meter. Then, check the jumper wire to the main power supply transformer. Be sure it is jumpered to correspond to your local line voltage value. If necessary, change the jumper wire to the transformer in accordance with the Jumper Chart in Section Three.
  • Replace rear cabinet door and screw (lock) it securely. NOTICE: Tamper proof screws are included with the spare parts. These screws are optional and may be used to secure the rear door panel. The T20 wrench (20-9620) is used for the installation of these screws. Close and lock the front coin and cash box doors.
  • To attach line cord, the four Phillips-head screws that mount the line cord cover plate to the rear cabinet. Match the prongs on the plug with the holes in the receptacle and push line cord securely into place. Make sure cord aligns with the indentation of plate (indentation should point toward bottom of cabinet). Remount line cord cover plate. If desired, tamper resistant screws are provided to remount cover plate.
  • Connect the line cord to a grounded (3-terminal) AC wall outlet.
  • Switch ON the game using the ON/OFF switch located on the upper left top of the cabinet, to verify proper operation.

1-4

Page 13

Servicing

Control Panel Switch OFF power to the game. Using the T27 wrench, remove four tamper proof screws from the monitor glass retaining bracket, and set bracket aside. Remove four tamper proof screws from under the control panel. Pull control panel out and disconnect the wiring. Before reinstalling the control panel, check for proper wire connections, including ground strap.

Remove Viewing Glass Switch OFF power to the game. Using the T27 wrench, remove four tamper proof screws holding the monitor glass retaining bracket, and set bracket aside. Carefully raise the glass from its bottom grooved edge and lift it clear of cabinet.

Remove Monitor Bezel Switch OFF power to the game and remove viewing glass (above). Remove bezel from its grooved edge.

Monitor Replacement We recommend that you read the WARNINGS section thoroughly before beginning this procedure. Switch OFF power to the game. Remove the viewing glass and the monitor bezel. Completely disconnect the monitor from all of its cabling, including its chassis ground strap. Remove the six flange nuts securing the monitors mounting flanges to its mounting panel. Pull the monitor carefully from the cabinet front.

Z\ caution While removing the six flange nuts, firmly support the monitor from the front of the CRT so that it will not slip.

Pesuvio The monitor DOES NOT contain an isolation

transformer in its chassis. It is mounted instead in the Power Chassis Assembly locate on the floor of the Cabinet. When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM THE LINE VOLTAGE WITH AN ISOLATION TRANSFORMER.

Remove Marquee Glass Switch OFF power to the game. Remove five 1/4” hex-head wood screws holding plastic strip above marquee glass. Set strip aside and carefully lift glass. Store glass carefully to prevent damage.

1-5

Page 14

° Remove Fluorescent Light Assembly Switch OFF power to the game. Remove marquee glass (above). Disconnect the fluorescent light assembly from its power cable: Remove the screws fastening the assembly to the cabinet and lift out the assembly.

WARNING If a fluorescent tube drops and it breaks, it will implode! Use care in handling.

. Replace Fluorescent Lamp Remove marquee glass (above). Remove the fluorescent lamp retainer brackets. Grasp the tube, give it a quarter turn and remove it from its socket. Carefully place a new tube into the socket and turn to reinstall.

. Remove Speakers Switch OFF power to the game. Two speakers are located in the control panel. Remove control panel (see above) to access these speakers.

One speaker is located under the seat. Slide the seat assembly forward, and use the T27 wrench to remove the two tamper proof torque screws from the base of the pedestal assembly. Slide the seat back and remove the two front torque screws. Remove seat assembly to access speaker.

. Diagnostics Switches Open the coin door. The Diagnostics Switches are located on a small bracket inside the coin door. The Begin Test Switch, closest to the door, activates the game's menu system. The Volume Up and Volume Down Switches raise and lower the sound level of the game. The Service Credit Switch, in the back allows credits to be allotted for service testing without affecting the game's bookkeeping total.

Page 15

Game Features

Crusin’ USA is a one player game.

Starting Up Switch ON power to the game. A "rug" pattern appears on the CRT screen. When the "rug" pattern ends, the screen shows CHECKING SCRATCH RAMS, and then CHECKING ROMS. The next screen shows CRUIS'N USA REVISION LEVEL, CMOS TEST OK, and the COIN SETTING. The game then moves to the Attract Mode.

Insert the desired amount of coins or tokens. Select which player receives the credit by pressing the appropriate Player Start Button.

NOTE: When an error is detected during Start-up Tests, game start-up does not progress, and an error message appears on the screen.

Player Controls

. Player Start Button (Green) The start button allows a player to begin game play.

. Radio Button (Orange) The radio button allows a player to listen to the radio and change stations.

. View 1-Low Rider Button (Red) View 1 drives the car from inside.

. View 2-Crus’n Button (White) View 2 drives the car from directly behind.

  • View 3-Sky Hi Button (Blue) View 3 drives the car from an arial view.

1-7

Page 16

Game Operation

The Crusin’ USA Control Switches are located inside thé coin door. These switches allow the operator to customize some features of the game.

CABINET SWITCHES

. The SLAM TILT SWITCH detects any forceful vibrations against the Coin Door. This eliminates pounding for free games. It is located on the inside of the coin door.

° The ON/OFF SWITCH is located on the right side, top of cabinet.

CONTROL SWITCHES

. The BEGIN TEST/ENTER SWITCH allows you to activate the games Menu System. Press the Begin Test Switch to access the Main Menu. To exit the menu system, select EXIT TO GAME OVER from the Main Menu, then press the Begin Test Switch. This switch will be referred to as SW1 throughout the remainder of this section.

. The VOLUME UP/+ SWITCH allows you to cycle forward through the menu selections or adjustment choices, and raises the sound level of the game. This switch will be referred to as SW2 throughout the remainder of this section.

. The VOLUME DOWN/- SWITCH allows you to cycle backward through the menu selections or adjustment choices, lowers the sound level of the game. This switch will be referred to as SW3 throughout the remainder of this section.

. The SERVICE CREDIT/ESCAPE SWITCH is a special feature switch that allots credit without affecting the game's bookkeeping total. This switch will be referred to as sw4 throughout the remainder of this section.

Page 17

Menu System Operation

OPERATION All CRUSIN’ USA Game Audits, Adjustments, and Diagnostics are options of the Main Menu. Each option, in turn, has its own menu, listing several choices that you may act upon as desired.

Press the SW1 to activate the Main Menu (shown below). Game adjustments, bookkeeping, and diagnostics are all accessible from this menu.

Press the SW2 or SWS button to cycle through the menu options. Notice that the options are highlighted in sequence. Press SW1 to activate a highlighted option.

Note: Only highlighted options can be activated.

DIAGNOSTIC TESTS

GAME AUDITS

GAME ADJUSTMENTS

UTILITIES

CALIBRATE CONTROLS

ADJUST VOLUME

EXIT TO GAME OVER

Main Test Menu

Page 18

DIAGNOSTIC TESTS To enter the Diagnostic Tests from the Main Menu, press SW2 to highlight that option, then press SW1 to activate. -

SWITCH TEST

DIP SWITGH TEST

CPU BOARD TEST

SOUND TEST

STEERING WHEEL TEST

MONITOR TEST

BURN-IN TEST

MOTION MENU

EXIT TO MAIN MENU

Diagnostic Test Menu

Switch Test The Switch Test allows the operator to test the switches on the control panel and the coin door.

Select the Switch Test by pressing SW2 to highlight that option; then press SW1 to activate. Pressing a switch on the control panel or coin door causes the corresponding switch location on the screen to light.

Press SW1 to return to the Diagnostic Menu.

DIP SWITCH TEST The DIP Switch Test allows the operator to check the position of the two 8-position DIP switches on the CPU Board. The operator can also change the setting of each position of each DIP Switch during this mode.

To enter the test, press SW2 to highlight the DIP Switch Test; then, SW1 to activate. The screen displays a layout of their current settings.

To change a DIP Switch setting, move the switch to the desired setting, then check the screen to verify that the switch now shows the new setting.

Press SW1 to return to the Diagnostic Menu.

Page 19

CPU Board Test The CPU Board Test (much like the Start-up Test) allows the operator to check the RAMs and ROMs. -

Highlight the CPU Board Test with SW2; then, press SW1 to activate the automatic test of the CPU Board's RAMs and ROMs. When this test is activated, a "rug" pattern appears on the screen. The screen then changes to show the layout of the RAMs and ROMs on the CPU. Any chip that is shown as black with a white outline is part of the CPU and should turn either red or green during the CPU Test. Any chip that is shown as gray with a white outline is not installed in the game. During the test, chips are good, if they turn green; they are faulty, if they turn red.

Sound Test The Sound Test allows listening to some of the sounds that Crusin’ USA is capable of producing. This test also emits a tone for each fault that is detected. After completion of this test, the main menu will be automatically returned to the viewing screen.

Monitor Patterns The Monitor Patterns Test provides a menu for testing the monitor. Highlight the test with SW2 and activate with SW1. Continue pressing the SW1 button to cycle through the test and automatically return to the Main Menu.

The COLOR BARS test fills the screen with several gradated colors to help with red, green and blue level adjustments Each color should appear sharp and clear.

The RED, GREEN, and BLUE SCREEN tests fill the screen with either red, green or blue.

The CROSSHATCH PATTERNS test fills the screen with a grid and a series of dots. The grid and the dots should be clear. The dots should appear round.

If any of the Monitor Pattern Tests shows a need for adjustment, use the proper white knobs on the Monitor Board.

Burn-in Test The Burn-in Test continually repeats the CPU Board Test. Press SW2 to highlight the Burn-in Test; then, press SW1 activate. When the Burn-in Test detects an error, the test stops and displays an error message on the screen. Use this test to find intermittent CPU problems.

To exit this test, switch the game OFF then ON again.

Page 20

GAME AUDITS To enter Game Audits from the Main Menu, press SW2 to highlight that option; then, press SW1 to activate. To advance to the next page of the Game Audit Table, press SW2, or press SW1 to exit.

The Game Audits Table records the game play statistics. The left side of the table names the Audit item; the right side shows the amount of play.

LEFT COIN — oO RIGHT COIN ©

SERVICE CREDITS o°

TOTAL STARTS - TOTAL CONTINUES — TOTAL ENDS

FREE GAMES ooo 0

EVENT

UNFINISHED GAMES

WATCHDOGS

PLAYS UNTIL HIGH SCORE RESET

Page 1 of Audit Table Qao0 0

AUTOMATIC SELECTED 0

MANUAL SELECTED Q

VETTE SELECTED

LABOMBA SELECTED

DEVASTATOR SELECTED

ITALIA SELECTED ooo$o

POWER ON TIME

GAME TIME

Page 2 of Audit Table

Page 21

SELECT ARIZONA

SELECT US 101

SELECT LA

SELECT IOWA

SELECT DEATH VALLEY

SELECT USA

SELECT BEV HILLS :

SELECT APPALACHIA

SELECT REDWOOD

SELECT RUSHMORE

SELECT CHICAGO eaoooo ogo coc 9 COCO Oo 8

Page 3 of Audit Table

START GGATE

START SF

START US101

START REDWOOD

START BEVHILLS.

START LA

START DV

Page 4 of Audit Table O20 OO oO. Oo

GGATE WINS

SANFRAN WINS

US101 WINS

REDWOOD WINS

BEVHILLS WINS

LA WINS

DEATH VAL WINS ARIZONA WINS _

GRAND CANYON WINS

IOWA WINS

CHICAGO WINS

INDIANA WINS

APPALACHIA WINS

DC WINS oooooaoloClOCClOCOCUCOCCUOCCO CD

Page 5 of Audit Table

1-13

Page 22

GAME ADJUSTMENTS

NOTE: Game Adjustments are explained in more detail cn the following page.

Press SW2 to highlight the Game Adjustment option on the Main Menu; then, press SW1 to activate.

The Game Adjustments option allows the owner/operator to change the Game Pricing and Game Difficulty.

The Game Adjustments Menu offers several options. Press SW2 to hig hlight an option; then, press SW1 to activate. The activated item provides a setting choice. Press SWS to change the current setting value; then, press SW1 to lock in the new setting value.

STANDARD PRICING

CUSTOM PRICING

FREE PLAY

FIRST PLACE AWARDS FREE GAME

GAME DIFFICULTY

TIME TO START

CHECKPOINT BONUS

ATTRACT MODE SOUND

HIGH SCORE ENTRY

MIN VOLUME LEVEL

SPEED IN MPH OR KPH

SPECIAL CD OFFER

EXIT TO MAIN MENU

Game Adjustment Menu

To exit the Adjustments Menu, press SW2 to highlight EXIT TO MAIN MENU; then, press SW1 to activate.

Page 23

Standard Pricing Standard Pricing allows the operator to choose any of the "Standard" selections for the Standard Pricing Table.

Custom Pricing Custom Pricing allows the operator to install pricing other than that of the Standard Pricing Table. Custom Pricing also allows the operator to select the amount of credits required to start a game and the amount of credits required to continue a game. This option is adjusted from the Dip Switch Settings.

Free Play This option selects free play. The setting choices for this adjustment are: -Off (factory setting) -On

First Place Awards Free Game Awards a player a free game on 1st position. The setting choices for this adjustment are: -On (factory setting) -Off

Attract-Mode Sounds Determines whether the game will make sounds in the attract mode. The settings for the adjustment are: -On -Off (factory)

Speed in MPH or KPH This determines speedometer setting in miles per hour or kilometers per hour. -MPH (factory setting) -KPH

High Score Entry This determines whether the game will allow High Score Entry and Display Table. The setting choices are: -On (factory setting) -Off

Page 24

Standard Pricing Table

Name. Settings Credit/Coin Left Chute- | Center Chute | Right Chute | Fourth Chute

USA 1125¢(2 to Start; 2 to Continue)25¢$1.0025¢
USA 21/25¢(2 to Start; 1 to Continue)25¢$1.0025¢
USA31/25¢(1 to Start; 1 to Continue)25¢$1.0025¢
USA41/50¢, 3/$1.00 (1 to Start; 1 to Continue)25¢$1.0025¢
USA51/50¢, 4/$1.00 (2 to Start; 1 to Continue)25¢tyo025¢
USA 61180¢(1 to Start;1 to Continue)25¢$1.0025¢
USA71/80¢, 3/$1.00 (1 to Start;1 to Continue)25¢$1.0025¢
USA81/50¢, 4/$1.00 (2 to Start; 2 to Continue)25¢$1.0025¢
USA ECA1/25¢, 4/$1.00 (2 to Start; 2 to Continue)$1.0010¢25¢5¢
German 1710M, 6/50M1DMSDM mi
German 24/1DM, 7/SDM1DM5DM
German 31/10M, 8/SDM1DM5DM
German 44/1DM, 5/5DM1DM5DM
German 51/10, 6/50M10M5DM
German ECA1/1DM, 2/2DM, 6/SDM50Ma20M
France 12/5F, 5/10FSF10F
France 225F, 4/10FSF10F
France 31V/5F, 3/10F5F10F
France 41/5F, 2/10F5F10F
France 52/5F, S/10F, 11/2x10F5F$0F
France 62I5F, A/10F, 9/2x10F8Flor
France 74/5F, 3/10F, 7/2x10FSF10F
France 8SF, 2/10F, 5/2x10FSF10F
France 94/3x1F, 2/5F1FSF
France 101/2x1F, 3/SF1FSF
France 114/3x1F, 2/5F, 5/2x5F1F5F
France 121/2x1F, 3/SF, 7/2x5F1F5E
France ECA_| WSx1F, 2/5F, 8/2x8F|1F10FSF
Canada1/2x25¢, 3/81.0025¢~_|$1.00
Swiss 1AF, 6/5F1FSF
Swiss 2ANF, 7/5F1FSF
Swiss 3AIF, 8/5F1FSF
ttaly |1/500 lire500 lire]s00lire |__|
UK1/20P,, 3/50P20P50P.
UK22/20P, 5/50P20PSOP
UK ECA1/20P, 3/50P, 7/£1.00£1.0020PSOP10P
UK Elec w/SCU1/30P,, 2/50P, 4/£1.00g1.00|ccu
Spain 14/100P, 6/500P100P-500P:
Spain 21/4X25, 1/100, 2/200, 5/50025P100P200P500P
Australia 1173x20¢, 2/$1.0020¢$1.00
Australia 25x20, 1/$1.0020¢$1.00|
Japan 11/100 yen100 yen100 yen
Japan 22/100 yen.100 yen100 yen
Austria 11/5 schilling, 2/10 schilling5 schilling10 schilling
Austria 21/2x5 schilling, 3/2x10 schilling5 schilling10 schilling
Belgium 11/20F20F20F
Belgium 23/20F20F20F
Belgium 32/20F20F20F
Belgium ECA1/20F50FSF20F
‘Sweden|1/3x1 krona, 2/5 krona1 krona,5 krona
New Zealand 1173x20620¢20¢
New Zealand 212x20e20¢20¢
NetherlandsAHF, 3/2.5HFItHFI2.5HFI
FinlandVi markka1 markkalTmarkka
Norway1/2x1 krone, 3/5x1 krone1 krone.{krone
Denmarkext krone, 3/5 krone, 7/2x5 krone1 kroneS krone
Antilles125¢, 4/1 guilder25¢1 guilder
Hungary17/2x10 forint, 3/2x20 forint10 forint20 forint
Page 25

Custom Pricing

(2) RETURN TO MAIN MENU —

  • LEFT CHUTE (1) UNITS
  • RIGHT CHUTE (2) UNITS
  • CHUTE (3) UNITS
  • CHUTE (4) UNITS
  • UNITS/CREDIT
  • UNITS/BONUS
  • MINIMUM UNITS REQUIRED
  • CREDITS TO START
  • CREDITS TO CONTINUE
  • COIN PAGE HELP
  • SHOW CREDIT FRACTIONS
  • COINS PER DOLLAR
  • MAXIMUM CREDITS

Coins inserted accumulate units. This adjustment specifies the number of units given for each coin in the fourth chute (see “units/credit") This is the number of coin units required to buy one credit. One bonus credit is awarded after this many coin units have accumulated. No credits will be awarded until this many coin units have accumulated. Each player needs this many credits to begin a game. Each player needs this many credits to continue a game. Whenever standard pricing is used, a corresponding message is displayed on the credits screen. Setting this to no disables the message. When set to yes, fractional credits will be seen on the credits screen. The detailed bookkeeping screen shows total collections based on this many coins per dollar. (Set to zero to disable the display of money totals.) This is the limit for the credits counter. Additional coins inserted will be lost. Factory setting is 30.

Page 26

UTILITIES

Press SW2 to highlight the Utilities option on the Main Menu; then, press SW1 to activate.

The Utilities Menu allows the owner/operator to clear the games bookkeeping memory and to install a custom message.

CLEAR CREDITS

CLEAR GAME AUDITS

RESET HIGH SCORES

DEFAULT ADJUSTMENTS — FULL FACTORY RESTORE

EXIT TO MAIN MENU

Utilities Menu

Press SW2 to highlight an item from the Utilities Menu; then, press SW1 to activate. After an item has been activated, you are given the option of resetting that item or not. For example:

CLEAR CREDITS? ARE YOU SURE?

Press SW3 to choose YES or NO; then, press SW1 to lock your choice and to return to the Utilities Menu.

To exit the Utilities Menu, press SW3 to highlight EXIT TO MAIN MENU; then, press SW1 to activate selection.

Page 27

Troubleshooting

PROBLEM

NO PICTURE OR DISTORTED PICTURE.

TURN GAME ON & NOTHING HAPPENS.

NO SOUND.

NO GENERAL ILLUMINATION.

MOVE JOYSTICK, BUT PLAYER DOES NOT MOVE.

PRESS START BUTTON AND NOTHING HAPPENS.

NO CREDIT GIVEN WHEN COINS ARE INSERTED.

TOO MANY CREDITS FOR NUMBER OF COINS INSERTED.

GAME STAYS IN THE TEST MODE. POSSIBLE SOLUTION

Check for faulty video board or monitor. Check for disconnected video signal cable.

Check line fuse. Check for +5Vdc at pins C, D, 3, and 4 of the JAMMA Connector.

Check the speaker and speaker connection to pins L and 10 on the JAMMA Connector. Check volume control setting. Check for +12Vde at pins F and 6 on the JAMMA Connector. Check interboard wiring on CPU Board. Check sound fuses.

Check the 1.0A., F.B. fuse located in the Power Chassis Assembly.

Check for open wires between the Joystick and CPU Board. Check for contamination on joystick switch contacts and CPU Board pins. Check for proper ground.

Check for open wires between the button and CPU Board. Check for contamination on CPU Board pins or the button switch blade contacts. Check for proper ground.

Check for contamination on coin switch contacts. Check for an open wire between Coin Switch 1 and pin 16 on the JAMMA Connector or Coin Switch 2 and pin T of the JAMMA Connector.

Check Game Pricing setting. Check for a Short between pins T & 16 on the JAMMA Connector.

Check that the Test Switch in the coin door and the Test Switch (Position 8) on DIP Switch 2 are set to Off.

1-19

Page 28

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 29

CRUIS’"N USA SINGLE SIT DOWN

SECTION

TWO

Parts Information

Page 30

Cabinet Hardware

Cabinet Assembly Lock Retainer Plate Upper Door Lock Cam Leg Leveler Plate Lock Plate Door Bracket Shaft Caster 20” Vent Hole Cover Leg Adjuster, 3.0” Door Cam Lock Caster Wheel

Coin Door Assembly

Tamper Proof Screw Tool, T-20 #555 Bulb, 6.3v Marquee Marquee Retainer Marquee Giass

Electronic Rack

Electronic Rack CPU Sound Board Assembly Power Supply Switcher Assy. Steering Wheei Driver Assy. Ribbon Cable, 20-pin Ribbon Cable, 20-pin

Speakers

Speaker, 40, Tweeter, 15w Speaker, 4 Q, 6", 25w Speaker Grill A-17889.1 01-7264 01-8989 01-9155 01-11285 01-1129 02-4404 03-7602 08-7377 20-6542-TB 20-9627

09-74000-33

20-9620 24-8768 31-2005 03-8252-5 08-7852

A-19301 A-19233-40033 A-15202-1 A-18004-40033 5795-10937-06 5795-14465-60

5555-12924-00 5555-12929-00 01-12816

Transformer Assembly

Power Pack Assembly A-19244 Dash Assembly

Dash Assembly A-19271

Fluorescent Lamp Assembly

Fluorescent Housing & Bracket Lamp Lock 18” Fluorescent Bulb, 15w

Monitor

Monitor, 25” Monitor Bezel Monitor Support Bracket

Cables

Line Voltage Cable Assembly Transformer Jumper Cable G.I. Jumper Cable Fluorescent Lamp Cable Switcher Power Cable Control Cable Line Voltage Cable Four Speed Shift Cable AC Power Pack Cable Cable Bass Speaker Main Harness Cable Video Signal Cable

Seat Assembly

Pedestal w/Seat Assembly

2-2 A-15890 03-8327 24-8809

5675-14041-00 03-9098 A-19501

A-19248 H-13378 H-15945 H-16303. H-17914 H-18175 H-18191.1 H-18737 H-19251 H-19256 H-19302 H-19357-3

A-19304

Page 31

A-15202-1

Power Supply Switcher Assembly

item PartNumber Description ~

  • H-17914 Switch Power Cable 2, 20-9920 Power Supply Switcher/UL
  • 01-12162 Shield for Switcher
  • H-15206 Ground Jumper
  • 01-10500 Power Supply Mounting Bracket

le) q le) a ma a a

  • i) 5 Ga GD
  • i —— i a)
  • re — io: fe c c ¢ aS c fe — io) =) > ¢ — is DC c c i) fe —ir. 5 5 ¢ fe c c ¢ 5 ¢ c ¢ — > a5 «< 5 GD ¢ — io i is aS fe —! 5 — ao) ¢ SS > ——) aS 5 ¢ aS i] ) —— i) c ——o—) > ) =< =a < fons) > =) ca c >

fo) q 0 fo) is GREEN/YELLOW YELLOW (-5¥)

RED (+5V) BLACK VIOLET/VIOLET-YELLOW

  • [k-© ORANGE (+ 12v) BLACK

48V 124, ® GND GNo sv 1A sev 28

ce) olfelfolfolfolfoljo

UU TOLLS

CAUTION HIGH VOLTAGE PRESENT WHEN GAME |S PLUGGED IN

2-3

Page 32

Part Number

‘A-18005 5340-12958-00 5340-12959-00 5311-12538-00 5311-14067-00 5311-14068-00 5311-10948-00 5430-13598-00 5372-13323-00 5371-14070-00 5370-12602-00 5700-12047-00 5370-14069-00 5160-10269-00 5100-13945-02 5040-08986-00 5040-12298-00 5040-13417-00 5791-10862-09 5791-10862-02 §791-10862-04 5791-12461-04 5791-09437-00 5791-12461-11 5791-10850-00 5791-12461-10 §791-12516-00 5633-13826-00 5070-09045-00 5551-09822-00 §671-13732-00 §010-10428-00 5019-09362-00 §705-14076-00 5701-14092-00 4006-01003-08 4008-01003-08 4406-01128-00 4408-01128-00 03-9129 A-18005-Al 5010-14093-00

5010-13363-00 5010-13844-00

5010-13593-00

§010-09134-00 5010-13594-00 5010-08931-00 5010-13372-00 5010-09999-00 5010-13596-00

5010-13364-00

5010-13371-00 5010-13365-00

5010-14065-00 5731-14094-00 5735-13853-00 Designator

U3 U7 U18 U13, U17 U4, U10, U14 U9 ul

P7, PB P4

D5, D6 u LED1 R112, R113. SR1-SR3

R23, R47, R116, R120 R121 R43, R44, R48, R49, R52 R30, R33, R34, A-18004-40033 Wheel Driver Board Assembly

Description

Wheel Driver Board Assembly .C. 26L831 ILC. 26L832 1.0. 74HC14 LLC. 74HC245 L\C. 74HC574 1.C. 74HC138 1.C. 751608 ILC. ADC0848 ILC. DACOB, D-A Converter LLC. ULN2064B Solder Socket , 24-pin, 3” 1.C. LM12, Power OP-AMP Trans, 2N3904 Bridge, 4.04, Cap., Electrolytic, 100yF, 10v Cap., Electrolytic, 100pF, 40v Cap., Electrolytic, 10,000uF Connector, 9-pin Header .156 Connector, 2-pin Header .156 Connector, 4-pin Header .156 Connector, 4-pin Header .100 Connector, 20-pin Rib. Header Connector, 11-pin Header .100

Connector, 10-pin Header .100 Connector, 34-pin Ribbon Fuse Clips 5x20mm Diode, MRSO1 Inductor, 4.7uH LED, Red Resistor, 4702, 1w, 5% Resistor, 4.7KQ SIP Heatsink, 4 Lead TO-3 Thermal Pad For Power AMP Mach. Screw, 6-32 x 1/2” Mach. Screw, 8-32 x 1/2" Nut, 6-32 KEPS Nut, 8-32 KEPS. Nylon Spacer Wheel Driver Assy., Auto-Insert Resistor, 02, 1/8w, 5%

Resistor, 100 Q, 1/8w, 5% Resistor, 100K Q, 1/8w, 5%

Resistor, 10K Q, 1/8w, 5% R36-R39, R46, R51, R55 R59, R63-R66, R115 R42 R26 R31, R35 R19 RE7-R74 R45, R50, R54, R58, R62 R1-R16, Resistor, 150K , 1/4w, 5% Resistor, 1K ©, 1/8w, 5% Resistor, 1K Q, 1/2w, 5% Resistor, 220 Q, 1/8w, 5% Resistor, 2K ©, 1/4w, 5% Resistor, 33K Q, 1/8w, 5%

Resistor, 33 ©, 1/8w, 5% R76-R83, A85-R92, R122 R114 R21, R24, R25, R27, R119 R41 FI, F2 F3 Resistor, 330 Q, 1/8w, 5% Resistor, 4.7K Q, 1/8w, 5%

Resistor, 75KQ, 1/8w, 5% Fuse, 4ASB, 5x20mm Fuse, 2ASB, 5x20mm

2-4 Part Number

5043-08980-00

5043-08996-00

5048-12577-00 5048-13375-00 5048-11031-00 5040-09343-00 5070-08919-00 5075-09135-00 5075-12824-00 5075-14066-00 Designator Description

B1-B4, B10-B19, Capacitor, 01pF,50v(+80,-20%) B7-B9, C31, C8, C9 C27, C29, C32, C35-C37 C28 10-C25 C1, C2, C39 C30, C33 D1 D4 D7, D8 D2, D3 Capacitor, .1pF, 50v,(#20%)AX.

Capacitor, .47yF, 50v, Axial Capacitor, 100PF, 50v,10% Ax. Capacitor, .001yF,50v,10% Ax. Cap. Electrolytic , 10uF, 20v Diode, 1N4148 Zener Diode, 10v, 1N4740A Zener Diode, 12v, 1N4742A Zener Diode, 15v, 1N4744A

Page 33

2-5 9d popenconncont (Beapesesason: Y e000} BoaocoaGea| t PS. : mg <3 ppopsrosuaneoneEn Besscccooed , , BESESEREESESESES| A-18005.1-Al Wheel Driver Assembly, Auto -Insert A-18005.1 Wheel Driver Board Assembly

Wheel Driver Board Assembly

A-18004-40033

Page 34

2-6 Part Number A-19234 5040-13417-00 5370-12602-00 5070-09054-00 5370-13419-00 5370-12730-00 5340-13304-00 5340-13597-00 5340-12558-00 5371-13299-00 §372-12901-00 5340-12958-00 5340-12959-00 5344-14130-00 8434-12255-00 5283-10551-00 5286-14178-00 5280-09309-00 5311-12538-00 5281-09500-00 5281-09487-00 5311-10948-00 5317-12023-00 §311-12043-00 5430-14290-00 5317-12208-00 5311-12287-00 5317-12211-00 5317-12212-00 5430-13598-00 5250-13303-00 5250-13302-00 5521-13806-06 Designator C191, C192 u122 D1-D4 U78, U81 U79, U80 U35, U41, U42 U85, U87 U31 U61 U130 ug2 ust U45, U58 U30 U62 US55 U82 U63 u36 U64 U34 uss U40, UST U126-U129 U44, U46, U48, ag, U98, U107, U108, U113 U33, U39, USO, U93, U104, U105, U109, U112, U116, U119, U120, U121, W125 U32, U47, U65, U66, U86, U110 U37, US53, U117, U124 U1085, U1010 U67 Description CPU Sub-Assembly Capelectro, 10,000MF, 35v ULN2064-Quad High Current Darlington Switch Diode, 1N4004 TDA2030 TLoB4 2K x 8 SRAM 62256, 32Kx8 BIT SRAM, 55nS 8Kx8 CMOS SRAM, 120nS

AS1851 ADC0844-8 BIT ATO D Converter w/4 CH. Multiplexer AM26LS31 - Quad Differential Line Drivers AM26LS32 - Quad Differential Line Receivers 1077204, CMOS Parallel FIFO 4K x 9 BIT, 20nS Max691, Power ON Reset/ WATCHDO/CMOS CTL Circuit 74F0O 74AS02 - ALS TTL Quad 2 Input NOR GATE 7407-TTL Hex Butter w/ High Voltage Output 74HC14 74LS32 74LS74 74HC138 74ALS138-ALS TTL 3/8 Decoder 74HC174 74176B-Bidirectional Transceiver 74ALS245, ALS TTL Octal Bus Transceiver 74HC541 - HC TTL Octal Buffer 74ALS541 - ALS TTL Octal Buffer 74ALS574 - ALS TTL Octal Flip-Flop 75160 - Octal interface Bus Trans.

LM79LO5T LM78LOST Xtal Osci tor, 38mHz Part Number 5521-13806-05 5521-13603-01 §20-13301-00 5671-13732-00 5556-14181-00 5100-13945-02 5733-14113-00 5700-12047-00 5700-12088-00 5881-12315-00 5645-09025-00 5641-12551-00 5791-10862-02 5791-12461-04 5791-12461-05, 5791-10862-07 5791-12461-12 5791-12461-13 5791-09437-00 5791-10850-00 5705-12638-00 5791-12994-00 4004-01005-06 4404-01124-00 A-19331 §052-14149-00 5052-14366-00 5052-14169-00 §052-14367-00 §052-14167-00 5052-14171-00 5052-14166-00 5052-14168-00 5052-14350-00 §052-14164-00 Designator Description us9 Xtal Oscillator, 40mHz uUg6 Xtal Oscillator, 50mHz ut Y10H 10mHz D5-D7 Light Emitting Diode, Red

135-137 FB700 BRI Bridge 4A F1,F2 Fuse Holder 38, U43, 1.C, Socket, 24-pin , 3"

U52, US4, U111, U114 U2-U29 LLC. Socket, 32-pin, 6” Bt Battery Holder U97, Sw3 DIP Switch, 16-Pin Swi ‘Switch PCB Mount MC Pt, P2 Connector, C156x2 2-pin P5 Connector, C100x5 5-pin Connector, C100x5 5-pin P4 Connector, C156x7 7-pin P9 Connector, C100x12 12-pin Ptt Connector, C100x13 13-pin Pa Connector, 20-pin Ribbon, .1” P10 Connector, 26-pin Ribbon, .1" Heatsink 52998 J6 Header

  • Mach. Screw, 4-40 x 3/8” : Nut 4-40 KEPS CPU Surface Mount Sub-Assembly C173, C174 Cap., 0805 22PF, 10%, 50v C88, 0118, C159, Cap., 0805, 47PF, 10%, 50v C160, C164, C197, C198, C212, s

©224:C226, 0229-0234, C255, C274, C275, C277, 279, C278, C299-C303 C115, C151:C153, C185:C157, C235, C237-C239, C241, C242, C256-C273, 280-0297 C123, 6190 Cap., O805PF, 5%, 50v c169 Cap., 0805, 470PF, 20%, 50v C95, C98, C111, C128 Cap., 0805, 680PF, 5%, 50v C94, C96, C99, C110, Cap., 0805, 1000PF, 5%, Sv

C127, 6228, C252 C97, C100, C129 Cap., 0805, 3900PF, 5%, 50v c109 Cap., 0805, 4700PF, 5%, 50v Ct-C8, C10, C11, Cap., 0805, 0.01MF, 10%, 50v

C13- C16, C18, C19, C21-C31, C33-C41, C43-C48, C52, C54, C55, C57-C64, C66, C67, C69, C70, C72-C75, C77:C80, C83, Cap., 0805, 100PF, 10%, 50V CPU/Sound Board Assembly A-19233-40033

Page 35

2-7 Part Number 5052-14164-00 5052-14435-00 5052-14385-00 5052-14369-00 5052-14165-00 5051-14150-00 5052-13633-00 5051-14371-00 5051-14151-000 §051-14148-00 5020-14349-00 5020-14372-00 5020-14373-00 Designator Description ©85, C87, C90, C101, C102, _ Cap., 0805, 0.01MF, 10%, 50v

C104, C105, C107, C116, C117, C120, C131, C132, 135-0138, C140, C142-C144, C150, C162, C163, C166, C175, C178-C187, C193-C196, C199-C209, C213-C218, €221-C223, C236, 0244-C251, C305, C306 C56, C71, C84, C89, Cap., 0805 10PF, 5%, 50v

C103, C119, C165, C219 ctas Cap., 0805 0.022MF, 10%, 50v 145-0147 Cap., 0805 0.047MF, 10%, Sv €20, 051, C53, C65, Cap., 0805 0.1MF, 20%, 50v

C65, C81, C82, C91, C93, C106, 112-0114, C121, C124, C125, C130, C133, C139, C141, C149, C167, C170, C176, C210, C211, C254 C108, C168 85328 0.22 MF TANT +10%, 50v C1109, 61130, C1032 Cap., 1208, 0.33MF, +20%, 50v 6126, C171, C172, Cap., IMF, 20%, 36v TANT

c189 ©9, C12, C17, C32, Cap., 10MF, £20%, 16v TANT

C42, C68, C86, C92, C134, C154, C158, C161, C177, C220, C227, 20, €243, 6253, C276, C278, C304 C122, C188 Cap., 22MF, +20%, 16v R2, R3, RG, R7, AY, Resistor, 0.0, 1/10w

A11, R16, R18, A19, R21, 23,24, R97, R192, A193, R238, A251, R372, A761 R937, R553 R12-R14, R35-R42, R60, R61, R63, R64, R6S-R76, AB9, R90, R92, R93, R96, R9B, F99-R104, R107, A110, Att, A412, A114-R122, R124-A147, R149, R153-R155, A157-A159, R161-R163, R166-R168, R172- R175, R180-R188, R191, R195, R197-R200, R205, R206, R208, R209, R211, R212, R222, R223, R225, R226, R228, R229, R231- R233, R235, R239, R241-R243, R245, R247, R250, R254-R258, R260, R264-R273, R276, R277, R279, R282, R284, R295-R299, R301, R304, R306-R310, R312, R314-R333, A335, R357, A3S9- R368, R370, R373-R375, A380- Resistor, 15 9, 1/10w, 5% Resistor, 0805 33 2 , 1/10w, 5% Part Number 5020-14373-00 5020-14161-00 5020-14161-00 5020-14152-00 5020-14374-00 5020-14375-00 5020-14160-00 5020-14376-00 5020-14377-00 5020-14378-00 5020-14379-00 5020-14380-00 5020-14345-00 5020-14155-00 5020-14172-00 Designator Description R414, R425, R426, Resistor, 0805 33 0 , 1/10w, 5%

R428-R432, R434, R435, R437- R467, R472, R484-R487, R491, R493, R494, R497, R499, R501, RS08-R524, R527, A528, A532, A537-R552, R567-A586, R632, R637, R688, R691, R694, R696, R697, R699, R700, R702, A703, R705, R726-R732, R734, R736, A738, R740, R742, R744, R746, R748, A751, R753, A754, R756, R759, R762, R764, R533 R26, R28, R30, R32, Resistor, 0805 47 9, 1/10w, 5% R34, R43-R49, Resistor, 0805 47 Q, 1/10w, 5%

R78-A87, A148, R215, R218, R219, R342, R344-R356, R358, R369, R420, R422, R423, R482,

R483, A554, R556 R25, R77, R123, R150, R178, R217, R341, R427, R436, R601, R609, R647 R737, R739, R743,

R749 Rags Resistor, 0805, 220 62, 1/10w, 5% R343, R610, R650 Resistor, 0805 330 ©, 1/10w, 5% R489, R628, R630, Resistor, 0805 470.9, 1/10w, 5%

A634, R635, R639, R641, R651, A654, RES6, R658, R659, R662, R663, R666, R667, R670, RE73, A674, R677, R678, R680, REB1, R685, R68E, R709, R710, A712, R713, R715, R716, R718, R720 R504, R560, R565 R473, R595 R475, R505, A561, A566, A619, A623, R626 F506, R557, R562, F602-R605, R607, R608, R640,

R643 R285, R287 Resistor, 0805 3.32K Q, 1/10w, 1% S07, A558, RS63 Resistor, 0805 4.7K Q, 1/10w, 5% R10, R27, R29, R31, Resistor, 0805 4.7K Q, 1/10w, 5%

R33, R50-R59, R62, R65, R88, ROT, R94, R95, R106, R108, R109, R151, R152, R156, R160, R164, A165, R169, R170, R176, R179, R194, R201-R204, A207, A210, A213, R214, R216, R220, R221, R224, R227, R230, R234, R252, A259, Resistor, 0805 100 , 1/10w, 5% Resistor, 0805 120 (2, 1/10w, 5% Resistor, 0805 487 22, 1/10w, 1% Resistor, 0805 680 0, 1/10w, 5% Resistor, 0805 1K Q, 1/10w, 1%. Resistor, 0805 2K , 1/10w, 1% (Continued) CPU/Sound Board Assembly A-19233-40033

Page 36

A-19233-40033

CPU/Sound Board Assembly

Part Number

5020-14172-00

5020-14172-00

5020-14173-00

5020-14158-00

5020-14383-00 5020-14156-00

5020-14384-00 §020-14381-00

5020-14174-00 5349-14131-00 5349-13599-00

5349-14132-00 5400-13298-00 5410-13465-00 5285-14342-00 §400-14129-00 §556-14348-00

8020-14347-00 (Continued)

Designator Description

R261-R263, R274, R275, R278, Resistor, 0805 4.7K Q, 1/10w, 5% R280, R281, R283, A300, R302, R303, R305, R311, R313, R334, R336, R376, A377-A379, R415, R421, R468, R469, R471, R480, R481, R490, R492, R495, R496, R498, R500, R502, R525, R526, R529-R531, A534, R555, A587- R594, R606, R611-R618, R622, R629, R631, R633, R636, R638, R642, R644-R646, R652, R653, R655, R657, R660, R661, R664, R665, R668, A669, R671, R672, R675, R676, R679, R682-R684, R687, R689, R690, R692, R693, R695, R698, R701, Resistor, 0805 4.7K Q, 1/10w, 5% R704, R706-R708, R711, R714, R717, R719, R721, R722, R755, R757, R758, R760, R470 R288, R289, Resistor, 0805 6.19K Q, 1/10w, 1% R290-R294, A338-R340, R419 R477, R478, R559, Resistor, 0805 8.2K , 1/10w, 5% R564, R625. R476 Resistor, 0805 9.09K Q, 1/10w, 1% R648, R649, R723- Resistor, 0805 10K Q, 1/10w, 5% R725, R733, R735, A741, A745, R747, R750, R752 R474 Resistor, 0805 11K Q, 1/10w, 1% R416, R417, R479, Resistor, 0805 22K , 1/10w, 5% R535, R596, A597 R418, R536 Resistor, 0805 47K Q, 1/10w, 5% U94, U9S, U101, U102 256K x 8 BIT VRAM, 70nS U69-U76 44C1000, 1Megx4BIT CMOSDynamic RAM, 60nS U56, US7, US9, U60 6226X, 128Kx8BIT Fast Static RAM 20nS 1 ADSP2105 U68 IC, VR1 ASIC U83, U84 74ALS374 20PSOL uso DSP TMS320C31, SOMHZ L1-L34, L38, L39, Inductor, FBO805. R765 R286, R424, R433 Resistor, 0805, 4.75K 0, 1/10w, 1%

2-8

Page 37

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 38

@ B io} way manuractuain: Comeany 1964

2-10 A-19331 CPU Surface Mount Sub-Assembly CPU/Sound Board Assembly A-19233-40033

Page 39

A-19271 Dash Assembly

i

ow 9, Lb og

OBNOMAON>

NO ce ee ek SOBNAHRONAO Part Number Description

A-19502 Dash Plate A-19503 Steering Mech. Mtg. Plate 03-7655-8 Clamp Cable, 1/2” 20-10117 4-Speed Shifter 20-10127-1 Switch P/B Rectangular, Red 20-10127-2 Switch P/B Rectangular, White 20-10127-3 Switch P/B Rectangular, Blue 20-10129-1 Switch P/B Circular Med, Start 20-10129-2 Switch P/B Circular Med, Radio 20-10134 Steering Wheel Assembly 5555-12924-00 Speaker, 4, Tweeter 15w 5555-12856-00 Speaker, 5-1/4", 4, 25w H-18175 Control Cable H-18737 Four Speed Shift Cable 4020-01100-20 TR, 1/4-20 x 1-1/4" 4420-01119-00 Nut, 1/4-20 ESN/NE 4310-01123-10B Bolt, 10-24 x 5/8 CB 4410-01128-00 Nut, 10-24 KEPS 4408-01128-00 Nut, 8-32 KEPS 4320-01124-12 Bolt, 1/4-20 x 3/4”

Page 40

A-19288

Monitor Cover Assembly

ItemPart NumberDescription
1.03-9099Monitor Cover
2.01-13419Shield Monitor Cover
3.07-6700Pop Rivet, 1/8” Dia.
4.4700-00096-00Flatwasher, 1/8x5/16x21ga.
Page 41

CRUIS’N USA

SINGLE SIT DOWN

SECTION THREE

Schematics and Wiring Diagrams

Page 42

NOTES

Page 43

JAMMA CHART

FUNCTION | WIRE COLOR WIRE COLOR FUNCTION

Ground Black Ground Black +5VDC Red +5VDC Red -5VDC Yellow +12VDC Orange Key Coin Counter 1_| Brown N/C N/C N/C Video Red Red Video Blue Brown Video Ground _| Shield

Test Black-Blue Start White

Coin 1 | Black-Brown

White-Black Black White-Brown Black White-Red N/C Black White-Yellow Black White-Green Black White-Blue Black White-Violet N/C N/C Ground Black Black Ground Black Ground Red +5VDC Red +5VDC Yellow -5VDC Orange +12VDC Key Brown-Red Coin Counter 2 N/C N/C N/C Green Video Green

White Video Sync

White-Gray Service

Black-Green Slam Black-Red Coin 2 N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C Black Black ClO|N| oon] &] jm) = lo} = = nm = wo = Bb = a = o>) = N = ao = o nN co} ie} ber nN Ne) nN wo ny ase nN a ny Oo ny Nj Le} ao

3-3

Page 44

3-4 120¥ JUMPER __ FROM POWER SWITCH 18-96 POR Sm POWER WIRING DIAGRAM

Page 45

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.