CATHODE RAY TOMES

Ace Driver Operation

Ace Driver (Namco, 1994) · Manual · 98 pages · 20 sections · original scan

Page 1

ACE DRIVER DELUXE

Operators Manual

It 1S THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY

AT ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY.

Part No. 90500019

Page 2

SAFETY WARNING

In Order to Use This Machine Safely

In order to use this machine safely, be sure to read this Operators Manual and the Installation and Commissioning manual carefully before installation and use of the machine. Whenever the owner of this machine entrusts disassembly, installation, adjustment, routine maintenance or trouble shooting to another person, the owner should ensure that they read the appropriate precautions and relevant sections of this manual before starting work. In order that no accidents occur when the machine is in operation, strictly follow the notes on safety described below. Also, carefully read section 3, "Precautions".

Warnings for Operation

NOTE:
NOTE:
NOTE:
NOTE: ~ Only operate this machine after checking that it has been installed correctly and in accordance with the Installation and Commissioning manual. Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There are warning stickers to keep hands and feet clear of moving parts, however if the operator feels that a customer playing the game is in any
danger, he should warn the customer accordingly. The warning stickers must always be kept in good condition and replaced if worn so that the customer can read them clearly. If there is an error or problem with this machine, operation must be stopped immediately. (If the Drive Castor is worn out, it should be handled according to section 6-9, "Handling Drive Castor Wear".) /

Warnings for Disassembly, Installation, Routine Maintenance and Troubleshooting

Va

DANGER:
DANGER:
DANGER:
DANGER:
NOTE: ~\ Namco Ltd. bears absolutely no responsibility for accidents or injuries resulting from unauthorized changes to the machine. Ensure that the machine has been turned OFF before making adjustments or carrying out maintenance. Also ensure only qualified personnel carry out maintenance or turn the power ON to this machine. The power supply and inside the monitor will remain hot and have areas of high voltage even though the machine has been turned OFF, and there is a possibility of burns or electric shock. Be careful not to touch these areas. In order to avoid injuries due to mis-operation, be sure that the voltage of the power supply is within the prescribed limits. Also to prevent possible electric shocks due to failure, this machine MUST be fitted with a securely connected earthed plug. Do not turn the main power switch ON until the machine has been installed correctly. S
Page 3

© 1994 MAMCOD Lta-altrights reserved.

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for public or private use, without permission from NAMCO Ltd.

While the information contained in this manual is given in good faith and was accurate at the time of publication, BRENT LEISURE LIMITED reserve the right to make changes and alterations without notice.

This machine has been manufactured in accordance with European Community directives (1st. January 1995), and as such bears the Cc € marking. Any changes or modifications to this machine must be in accordance with European Community directives (1st. January 1995).

If you make any unauthorised changes to this product, you may contravene European Community directives (1st. January 1995)

Published by: BRENT LEISURE Ltd. Unit 1 Brent Crescent, London. NW10 0QT

Phone:- 0181-965-0550 Fax:- 0181-961-0574

Page 4

Contents

HOW TO PLAY oc escsssessesssseseeesscssseseeeesescessesesseasasssseaueesessesseseeessssseteseesesseseseeesasesseaeees 1

SPECIFICATIONS .......cccccccscsesesesseseseseesessssseseescasenseseeseecsessseeeeessseseeseeesisesseseeusasesseseeeteeee 2

PRECAUTIONS sseccosssouruacecseccsansamanssaconeueansassensssonaassnouasecencenausamonasaseneuennsastengesoraassaavasees 4

S14. Notes On Operation sisi inisinsvinsi amines inencanesesin isnainviiiase aaesataasti 4 3-2 Notes on Installation .........ccccceseeseseeeseessesssseseseescecssseeseeeeessssessseseseeesasesseseaeeets 5

3-3. Notes on Moving and Shipping 3-4 Notes on Handling

MAJOR: GOMPONENTS? svccorsssosrsssccrenesvsssemenesnsaadatessstooncensacsncseanrgnnnvantennnsdesssrmnvenguasexaras 8

ADJUSTMENTS. ......cccccccsscseceseeseseseseesescesscsesescsssssesueesesscsseeeeessssseseseessessesesesisesesseaeeetenics 9

5-1 Turning on the Power . 5-2 Adjustment Switches 5-3 Test Mode

5-3-1 Coin Options 5-3-2 Gamo Oplionssniccssissicnsisiavscsievasavsessasaseasscracesivain icvsasanatansseteasincneses 12 5-3-3 I/O Test 5-3-4 Switch Test

5-3-5 MOtOr TeSt.......ceeseecscscesesesseeeesseseseseeeeeessesssseseeeeesecsssceseeeeeesisesenseseaseesesee 5-3-6 — Motion Stop Test .........:ccccccecessssssseseeseseeseseseeeesensssseseseeeessesessnseaeeeseeesis 16 5-3-7 Lamp Test. 5-3-8 LED Test

5-3-9 Sound Test 5-4 Linking Two or More Machines. ............ccccecssssseseseesesseeseseseeeseessseseeseseaseneecesees 19 5-4-1 Setting the Link Switches 5-5 Adjustments When Replacing Parts (Initialization) ............::cecseeseseseeeeeee 21

MAINTENANCE... cscsesces ce esesceseesescesesceseeescesesesteseessnesesnssnsesessesessaseesenenseneensneseas 22

6-1 Cleaning the Under Base... cccsssssssesssssssssssseseeseersssesssesstsnsnsseasesessessesess 22 6-2. SIGN ASSEMDLy .......cscsscecseseseceseeseseeeeeeessesseseseseecscseseeeeessssesetesssisesseseeneasenseeeenee 23 6-2-1. Replacing the Fluorescent Tube and Reflector Lamp ..........::s1se 23 6-2-2. Replacing the LED Drive PCB .23 6-3. Main tower ASSY. ........cccceseseeeeeeeseeee .24 6-3-1. Replacing Fluorescent Lamp and Reflector Lamp.........:cssssseeseee 24 6-3-2. Removing the Game PCB .........cccsssssssseseessssnssesssesetseseessesesseseeeesees 24 Removing the Shield Case . .25 Removing the I/O Board . 225 Replacing the Switch Mode Power Supply and Fuses. -26 Replacing the Amplifier. ...........cccccccsccssssssssseseeeseeeesessssseseseeesesssseseeeneees 26

Page 5

6-4. Removing the Monitor.. Steering and Shift Lever .. 6-5-1. Replacing the Steering Wheel . : 6-5-2. Shift Assembly Maintenance ............ccccccececeeseeseseeeenessesesseseeeeneesseseeeees 29 6-5-3. Replacing the Steering Drive PCB .........cccccsscseseeeseeestessesesseseseeeeeeeees 30 6-5-4. Replacing the Time Belt 6-5-5. Replacing the Motor and Motor Brush 6-5-6 Replacing the Pulley 0... eee eeeneneeseeaeeecenseeeeeceneees 6-5-7. Replacing the FUSC ...........ccccsssesesseseeseseseeeeeesssssseeeeseseeesesesseaeeeeeeesees 6-5-8. Replacing the Control Pot. 6-6. Replacing the Seat . 6-6-1. Removing the Seat . . 6-6-2. Installing tho’ Seal ssscscssscscinastsasccssevsssuscsssvesinansavnsaianevavensa saves sasazennent 6-7. Under Base ASSEMDIy ........ccccececseseseesssseseesessesseseeeeecsessseeeeeeesesseseaensesssseaeeeees 6-7-1. _ Removing the Rear Covers (L), (R) 6-7-2. Names of Under Base Parts . 6-7-3. Replacing the Drive Castor... . 6-7-4. Replacing the Drum Drive PCB and Motion Stop PCB ...........::cc08 42 6-7-5. Replacing the V Belts ..........cccscseseseesssscseseeeeeeesessseseeeenessesesseseaeneeses 6-7-6. Replacing the Motor and Motor Brushes. 6-7-7. Replacing the Motor Fuse = 6-8. AB Pedal ASSOMDLy ........c.cccceccesesesececssssseseseesessssseseesesseseeeeeesisesseseeseesesseseeeteces 6-8-1. Removing the AB Pedal Assembly ............::ccccccecesesssssseseseseseeteneeeeties 45 6-8-2. Replacing the Control Pots 6-9. Handling Drive Castor Wear .. 6-9-1. Checking drive Castor Wear. ss 6-9-2. Action When the Drive Castor is Worn OUt ...........:cceeseeeeseeeseseseeeeeees 46

TROUBLESHOOTING .....c.ccccesesecsccsssseseeceeessssseeseeseeessasssseseseeeeessesssseeteseessecesesseeentes 47

PARTS sessesresssnvasccusassuessnvavessosnsengpsasnsnnesemnessnnvasseuss sass seu ayestasnsonguaaaamuesemenennaasecuea cuss set ce 48

Page 6

1. HOW TO PLAY

This machine is a multi-player racing game that allows several people to play at the same time, up to a maximum number of eight. When two or three players are competing against each other, the computer car is included and competition is between four cars. When four or more players compete against each other, competition is amongst those players only. When only one player is playing, he/she competes against the computer cars.

[Game Summary] The object of the game is to complete the set number of laps as fast as possible within the set time. The game is over after completing the set number of laps. The finishing position, lap time, and total time are displayed at the end of the game. If the set time runs out (becomes "0") before the laps are completed, the game is over.

[Starting the Game] Insert a coin/s. Move the shift lever up or down to select the method of shifting, AT (auto) or MT (manual) and then depress the accelerator. Next, move the shift lever up or down to select the level of difficulty (beginner, expert, expert (pro)) and then depress the accelerator. Expert (pro) is selected by selecting expert and depressing the accelerator while at the same time pressing the view change button. In a linked game expert (pro) class is set only if all participating players select it. After making selections, wait for the empty seat entry. A linked game starts when all of the connected seats have been entered, or when another player enters from another seat within twenty seconds after the coin/s have been inserted. If there is no entry by another person within the twenty seconds, the game starts as a single player. A single player game can be started without waiting for other players by inserting a coin/s while pressing the view change button.

Page 1

Page 7
  • SPECIFICATIONS

POWER SUPPLY :- 220/240volts AC

POWER CONSUMPTION:- 720W

MONITOR :- Hantarex 28" Polo Colour Monitor with auto degauss.

DIMENSIONS :-

  • Assembled: 2,370mm(w) x 2,180mm(d) x 2,200mm(h)
  • Separated: Seat Assy 1,070mm(w) x 2,030mm(d) x 1,640mm(h)
Tower Assy2,100mm(w) x850mm(d) x 1,760mm(h)
Header Assy1,380mm(w) x842mm(d) x = 325mm(h)
Sign Boards440mm(w) x170mm(d) x490mm(h)

WEIGHT:-

  • Assembled: 1,112kg
  • Separated: Seat Assy 360kg (x2) Tower Assy 348kg Header Assy 32kg Sign Boards 6kg (x2)

== [0000 === a Ea 2, 200

| a i) IEEE |

Page 2

Page 8

ACCESSORIES :- Keys: (Cash Door) (Coin Door). (Back Door)

IEG Mains Lead ..cccsssesssssassessssecisesarasserneinnrarniesessnenssa 1

Operators Manual...

Installation & Commissioning Manual .............:::ceesseeeeee 1 Monitor Manual. scsisccsisssssascssisstonscctesassasesasiesssnnnsavasssinaenansos 1

Car Number Decal Set - Large ........ccccceeseeeeseeseeteeenee 2

Car Number Decal Set - Small ...........:ccceeceeseseseseseeseeeeeee 1

M10 Security Wrench ........ccscsccsccceseseeeeeesessesseeeseeeeeesensesess 1 M8 Security Wrench ou... ccsessccecessensesssenensssisssensesees 1 M6 Security Wrench... eseseeeeeessetesseseeeneeeeeee 1 M5 Security Wrench ........cccceseceesseeseseseeeeeeeeeseseseeseeeneesenee 1

Link Cable 6 Metre sccisissscisacisssscsssssassccsssiaaianeieiaissasecsasacs 1

Steering Control Pot (Cont. Rotation)... 1 Header Sign Board - LHS ........c.cceccecesesseeseseseseseseessesenees 1

Header Sign Board - RHS ..........cccccecesseeesesesneteseeseseaees 1

Seat Base Extension Brkt - LHS/RHS ...........cccsceeseseeeeee 4

Floor Safety Mat - LHS... cccscseseessssssssssesessestesssseseseeeees 1

Floor Safety Mat - RHS ........ccccscecseeceseeeesessseseeeeeesessesees 1

Floor Safety Mat - Centre ........ccccsssssssssessssessssssseceseeseenes 1 Rear Guard Fence.........cccccccsesscssesseseseeeeeesesesssseseeeeneeeece 1

Rear Guard Fence Securing Brkt...........:cccesesesseseseees 4

Safety Skirt .......cccccseseseeceseseeeseessssseseeeeeessesseseseeasenseeees 2 Safety Skirt Stay ......ccccsescesessseeseseseeeeeeesesseseseeeneesesseeeees 2

M10x25 Hex Head Screw

M10 Flat Washer - H/Duty M10 Spring Washer Type B . M8x20 Security Button Head Screw .

M8 Flat Washer - H/Duty M8 Spring Washer Type B

M6x20 Security Button Head Screw .

M5x16 Security Button Head Screw . M5x12 Security Button Head Screw . RRO A No6x¥" Pozi Flange Head Screw..

Page 3

Page 9
  • PRECAUTIONS Be sure to read this section carefully

3-1. Notes on Operation

NOTE:
NOTE:
NOTE:
NOTE:
NOTE:
NOTE: Only operate this machine after checking that it has been installed correctly and in accordance with the Installation and Commissioning manual. The supplied guard fence is to ensure customers do not get too close to the machine or get injured. Make sure that the fence is fitted to the machine correctly and the rubber safety mats are in place. Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There are warning stickers to keep hands and feet clear of moving parts, however if the operator feels that a customer playing the game is in any
danger, he should warn the customer accordingly. Ensure customers do not get hurt by leaning or climbing on the seat base or fence. Be especially careful in the case of young children. The warning stickers must always be kept in good condition and replaced if worn so that the customer can read them clearly. If there is an error or problem with this machine, operation must be stopped immediately.

Parts of this machine move to the left and right during the game. In order to maintain the customer's safety, the operator should strictly follow the appropriate precautions.

NOTE: Ensure no items are placed on the seat base next to the seat assemblies to prevent damage to the machine.

Page 4

Page 10

3-2 Notes on Installation

1. following places: This machine is designed for indoor use only. Do not install the machine in the

io) Direct sunlight, places with excessive humidity or

dust, places where there is water leakage, near airconditioning or heating equipment, places with excessively high or cold temperature.

[ @® Places where it would be in the way of emergency exits or fire extinguishing equipment.

®

Page 5

Page 11
  • If this machine is installed next to walls or other machines, ensure there is plenty of space between them
NOTE: So that customers are not crushed or injured while the machine is moving, ensure that it is separated from walls or other machines by at least 30cm.
NOTE: In order that the PCB rack or power supply can be removed for service, make sure that the rear of the machine is separated from a wall or other machine by a distance of at least 50cm or more.

30 cm or more 30 cm or more

3-3. Notes on Moving and Shipping

NOTE: If the seat assembly is not secured to the seat base, there is a danger of the seat assembly moving left or right during shipping. Ensure that the shipping brackets (two for each seat assembly) are fitted securely.
NOTE: The tower assembly has a high centre of gravity and is unstable when standing alone. Do not use a forklift when moving or shipping.

. Take care not to damage the machine when moving or shipping.

. Take care not to rope moulded (plastic) parts when shipping.

: Ensure that the levellers are raised fully when moving the machine, even for short distances.

. The seat assy, tower assy and side boards must be separated when shipping.

: If a forklift is used to move the machine, use it only to move the seat assembly and only insert the forks in the places indicated on the side of the assembly.

Page 6

Page 12

3-4 Notes on Handling

/ Va

DANGER The Mains voltage to this machine should be within the range of 220 to 240v AC and the transformer input matched accordingly.
DANGER Be sure that the power is turned OFF when replacing parts and connecting/disconnecting connectors.
DANGER to prevent possible electric shocks due to failure, this machine MUST be fitted with a securely connected earthed plug.
DANGER The monitor and power supply contain areas of very high voltage. Be extremely careful when inspecting or making adjustments.
DANGER When unplugging the game from an electrical outlet, always grasp the plug, not the mains lead. XN

NOTES:

. Always return PC Boards to your dealer for repair. Never test the PCB for continuity with a multimeter or similar device. The PCB contains sensitive devices which could be damaged or even destroyed by the internal voltage of such test equipment.

7 Adjustments are required after replacing the game PCB, ROM, Steering Assy, AB Pedal Assy and control pots. Adjustments should be performed as described in section 5-4, "Adjustments (page 19). when Replacing Parts'}

. After initial installation or if the number of machines linked together changes, it may be necessary to use the test mode to change the settings_and link switch settings. (Refer to section5-4, "Linking Two or More Machines'{ (page 19).

Page 7

Page 13
  • MAJOR COMPONENTS

Sign Assy

Sign board (L) Main tower Assy

ae Sign board (R)

Cl Monitor (R) Assy

-——-AT Ty) ss Monitor (L) Assy

Shift Assy

Steering Assy Seat Assy

Fence (accessory)

Upper base Assy 7

xX i BSS Seat base Assy AB pedal Assy i °

Ke Shipping Brkt

Uo \I Coin Assy Roller base Assy

Power Supply Fuses Amplifier

Shield case

Transformers for drum motors

Mains In & Power Switch & Fuse’

Page 8

Page 14

5 ADJUSTMENTS

5-1 Turning on the Power

After the machine has been installed, turn ON the power. The Power switch is located on the rear of the upper tower section. (See section 4 "Major Components'| (page 8).)

5-2 Adjustment Switches

The adjustment switches are located inside the coin door.

  • Service Switch Press this switch to obtain game credits without incrementing the play meters.
  • Test Switch Slide this switch "ON" to enter test mode. Test mode allows game testing and the changing of game settings. (Refer to

section 5-3 "Test Mode'f (page 10).)

COIN COUNTER o

°

LEFT PLAYER RIGHT PLAYER

TEST SERVICE TEST SERVICE © ©

Service Bracket

Page 9

Page 15

5-3 Test Mode

Open the coin door and slide the test switch "ON". The "Menu Screen" will be displayed on the monitor.

Select the test required by moving the shift lever up or down. The colour of the selected test will change.

Enter the selected test by stepping on the accelerator. Select "EXIT" to return to the "Menu Screen" (step on the accelerator when using the monitor test screen).

After testing is completed, ensure that the test switch is returned to the "OFF" position to return to game mode.

The Test Switch must always be in the "OFF" position for normal game mode.

MENU

COIN OPTIONS

GAME OPTIONS

VO TEST

MONITOR TEST

SOUND TEST

ADS DATA

OTHERS

: ENTER SHIFT: CHOOSE )

Page

  • Sets the price of play.|(See 5-3-1)
  • Sets the game options|(See 5-3-2)

(3)

(4)

(5 Used for te: ting the switches and motor. (See 5-3-3)

Used for ad justing the monitor.

) justing the speaker volume. (See 5-3-9)

  • Displays the accumulated game data.
  • Used for testing the PC boards and for initializing al Il of the settings.
Page 16

5-3-1 Coin Options

» Select item (1) "COIN OPTIONS" on the menu screen, to set the game cost and related settings.

b. Use the shift lever to select the required item then step on the accelerator.

c. Use the shift lever to change the settings then step on the accelerator to store the new values.

d. Select "EXIT" to return to the menu screen.

(COIN OPTIONS [DEFAULT IN GREEN] )

GAME COST 1 COIN 1 CREDIT

COIN1 MECH VALUE 1 COIN COUNT AS 1 COIN

COIN MECH 2 VALUE 1 COINCOUNTAS1 COIN _ .......p..

BONUS FOR QUANTITY BUY IN NONE eee

FREE PLAY OFF

EXIT

\ GAS: ENTER SHIFT: CHOOSE

Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the Coin Options on the screen are set as shown in the following table.

TEM CONTENTS FACTORY SET

(a) Game CostCoins required for 1 credit - - - - - - settable 1-91
(b) Coin 1 Mech ValueNumber of pulses on meter per coin - - - - - - settable 1-91
(c) Coin 2 Mech ValueNumber of pulses on meter per coin - - - - - - settable 1-91
(d) Bonus CoinExtra coin pulse at specified coins inNONE
(e) Free PlayGame started by pressing accelerator - - - - - - Yes/NoNO

Page 11

Page 17

5-3-2 Game Options

Select item (2) "GAME OPTIONS" on the menu screen to set the game options.

Use the shift lever to select the required item then step on the accelerator.

Use the shift lever to change the settings then step on the accelerator to store the new values.

Select "EXIT" to return to the menu screen.

Note: Race Class (c) must be set first before changing items (d), (e), or (f).

(See page 13 for descriptions) PCB ID NUMBER

TEAM COLOUR

RACE CLASS BEG EXP PRO (GAME OPTIONS [DEFAULT IN GREEN] >)

BLUE3

DIFFICULTY=BOBOBattttcee
LAPS[LINK]= 3034haceetees
LAPS[SOLO]334

SPEED DISPLAY KM/H

SOUND IN ATTRACT ON

EXIT

\ GAS: ENTER SHIFT: CHOOSE

NOTES

The rank (level of difficulty) and number of laps must be set the same on all positions that are linked.

The PCB number of the seat furthest left (when facing the front of the machine) should be set to 1, and the other seats set to 2, 3, 4 and so on in order from left to right. The PCB number of the farthest right position should equal the number of positions linked.

incorrectly. Settings other than those described will cause the machine to operate

Page

Page 18

TEM DESCRIPTION FACTORY SET

  • PCB Number The PCB number should be set so that none of the linked positions have the same number
  • Team Colour RED 25 or 26

BLUE sor4

YELLOW 170r18

GREEN 11 or 12

  • When more than three sets (6 seats) are linked, different race numbers should be used for the same team colours.
(c) RaceBEG(d) Game difficulty level (time)A (long) to D (short)B

Class

(e) Number of laps (linked game)3to63
(f) Number of laps (solo play)3to63
EXP | (d) Game difficulty level (time)A (long) to D (short)B
(e) Number of laps (linked game)3to63
(f) Number of laps (solo play)3t063
PRO(d) Game difficulty level (time)A (long) to D (short)B
(e) Number of laps (linked game)3to64
(f) Number of laps (solo play)31064
(g) Speedo UnitsKM/H/MPHMPH
(h) Attract SoundON / OFFON

Page 13

Page 19

5-3-3 I/O Test

  • Select item (3) "I/O TEST" on the menu screen.
  • Use the shift lever to select the required item then step on the accelerator.

(vo TEST >)

DIP 2 12345678 3 12345678

  • Option Switch (CPU-PCB Sw2)
  • Option Switch (CPU-PCB Sw1)

LINKON 2 COUNT 0 (c) Link Check

SWITCH (d) Switch Test MOTOR (e) Motor Test LAMP (f) Lamp Test LED (g) LED Test EXIT

GAS: ENTER SHIFT: CHOOSE NN /

  • Displays the state of the option switch, SW2, on the game PC board (CPU- PCB).
  • Displays the state of the option switch, SW3, on the game PC board (CPU- PVB). For both items (a) and (b), the switch is ON when the numbers are shown in red.
  • Displays the number of positions linked. If there is a link error, "ERROR" is displayed. The numbers to the right of "COUNT", display the number of link errors detected during the I/O test.
  • Tests the switches.| (See 5-3-4.) (See 5-3-5.) Tests the motors. Tests the lamps.
  • Tests the LEDs.

Page 14

Page 20

5-3-4

  • Accelerator
  • Brake
  • Steering
  • Shift

Sets Switch Test

The following screen is displayed when "SWITCH" is selected on the I/O screen.

( VO TEST >

DIP 2 12345678 3 12345678

LINK ON 2 COUNT 0

SWITCH

GAS:*0000COIN 1:OFF(e) Coin 1 switch
BRAKE *0000COIN 2:OFF(f) Coin 2 switch
STEER *0000SERVICE:OFF(g) Service switch
wtgaansecye] aves SHIFTCENTREVIEW:OFF...(h) View change switch

TO EXIT, STEP ON GAS AND SHIFT UP Ne

When the accelerator is stepped on, the number increases in the + direction. When the brake is stepped on, the number increases in the + direction. When the steering wheel is turned to the right, the number increases in the + direction, and when it is turned to the left, it increases in the - direction. When items (a), (b), and (c) are in their middle position, "0000" is displayed. (It is normal for the last digit to change.) Just before the steering wheel is as far as it will go, or just before stepping on the accelerator or brake as far as they will go, "Ok" will be displayed to the right of the number if everything is correct. Displays the position of the shift lever (CENTRE, UP, DOWN) and the state of the switches. When the shift lever is pressed forward, switch 1 goes "ON" and "DOWN" is displayed, and when it is pulled back, switch 2 goes "ON" and "UP" is displayed. When coin 1 switch is operated, "ON" is displayed. Unused. Goes "ON" when the service switch inside the coin door is pressed. Goes "ON" when the view change button is pressed

To return to the menu screen, move the shift lever up and step on the accelerator.

Page 15

Page 21

5-3-5 Motor Test

(a) The following screen is displayed when "MOTOR" is selected on the I/O screen.

(— VO TEST >

DIP 2 12345678 3 12345678

LINKON 2 COUNT O

SWITCH MOTOR BASE MOTOR OFF STEERING OFF TORQUE 00 EXIT

  • Seat motor test
  • Steering motor test

GAS: TURN SHIFT: CHOOSE

Tests the seat roller motor.

When "BASE MOTOR" is selected and the accelerator is pressed the test is "ON" and the motor starts to operate. Pressing the accelerator again turns the test "OFF" and the motor stops.

Tests the steering feedback motor. When "STEERING" is selected and the accelerator is pressed the test is "ON" and the motor will start and turn the steering wheel left and right. When performing this test, ensure that test (a) "BASE MOTOR" is also "ON". Pressing the accelerator turns the test "OFF" and the motor will stop.

Select "EXIT" to return to the I/O test screen.

Note: Performing the steering motor test can be dangerous, sit on the seat properly, and take hands off the steering wheel.

5-3-6 Motion Stop Test

The Stop Motion Switches will illuminate as soon as the test switch is turned ON.

To test the motion stop switches enter motor test (Refer to section 5-3-5, "Motor Test" above.) and select Base Motor ON.

Each time a stop motion switch is pressed, the motor will stop and restart when the switch is released.

NOTE: If this switch is pressed during game mode, the seat motion will stop and stay off for the remaining duration of the game

Page 16

Page 22

5-3-7 Lamp Test

The following screen is displayed when "LAMP" is selected on the I/O screen.

( VO TEST *)

DIP 2 12345678 3 12345678

LINK ON 2 COUNT 0

LAMP. TOP LAMP SIGNAL LAMP RED SIGNAL LAMP GREEN EXIT

GAS: LIGHT SHIFT: CHOOSE Ne S

  • Tests the top lamp.
  • Tests the red signal lamp.
  • Tests the green signal lamp.

Select "EXIT" to return to the I/O test screen.

5-3-8 LED Test

The following screen appears when "LED" is selected on the I/O test screen.

(110 TEST >)

DIP 2 12345678 3 12345678

LINK ON 2 COUNT 0

EXIT

GAS: LIGHT SHIFT: CHOOSE

  • Tests the finish position LED.

Select "EXIT" to return to the I/O test screen.

Page 17

Page 23

5-3-9 Sound Test

To adjust the sound volume, select "SOUND TEST" in the menu screen. The following screen will be displayed.

  • Left speaker volume SOUND TEST [DEFAULT IN GREEN]

VOLUME [MAX 63] LEFT RIGHT ences 40 40

SONG 40

EXIT

GAS: ENTER SHIFT: CHOOSE

Select (a) or (b) by using the shift lever, the characters will accelerator is pressed the numbers will start to blink. Moving the shift lever up will increase the number, moving the shift lever down will decrease the number.

  • Right speaker volume

blink in red, when the

The volume can be adjusted in 64 steps, with 00 the lowest and 63 the loudest. The factory setting is "40"

Select "EXIT" to return to the menu screen

Page 18

Page 24

5-4 Linking Two or More Machines.

Up to four machines (8 seats) can be linked together. The machines should be linked as described below.

NOTE: Each machine can draw up to 8 amps. Make sure that the power supply

1)

2) is adequate.

Ensure that the power is "OFF".

Loosen the two screws (M4x10) on the back of the tower assy, and remove the connector cover.

Connector cover

» screw (M4 x 10)

Link switches Set the link switches to "ON" , "EXT", and "ON". (See Diag.)

Use the supplied link cable and connect the machines between "IN" and "OUT" sockets (See Diag.)

[Examples of Linked Machines]

a)

2 MachinesoO6©oO
(4 Seats)INOUTINOUT
3 Machineso6ooOooO
(6 Seats)INQUTINOUTINQUT
4 Machines866Oo6Oo6oO
(8 Seats)INOUTINOUTINOUTINOUT

as

Page 19

Page 25
  • Turn the power to each machine "ON", and set the PCB ID using the test mode. (Refer to section 5-3-2, "Setting the Game Options"| (page 11))|
Note: Settings other than those described will cause the machine to operate incorrectly.

5-4-1 Setting the Link Switches

The link switches are used to set the connection between seats and machines.

1). Setting only one machine (2 seats)

Set the link switches to "ON", "INT", and "ON".

Note: Do not use a link cable.
  • Setting two or more machines.

Set the link switches to "ON", "EXT", and "ON".

screw (M4x 10) °

  • Install the connector cover using the two screws (M4x10). ° . . Z yt r The link procedure is now complete.

Link cabie

  • Setting for faulty PCB. If the game PCB of only one side is faulty, set the link on that side to "OFF"

[Example of setting for faulty left side]

G77

Seat with problem

Page 20

Page 26

5-5 Adjustments When Replacing Parts (Initialization)

The following adjustments should always be performed after replacing the game PC board, ROM, Steering Assy, Pedal Assy, or Control Pots. The game will not operate correctly if these adjustments are not made.

  • Ensure that accelerator and brake pedals are fully returned.
  • Place the steering wheel to it's centre position and remove hands from the wheel

(The steering wheel does not return to centre by itself.)

  • Slide the test switch "ON" while pressing the service switch. The following

(— > ADJUST MODE

BASE BIAS VALUE

STEER:********0000
GAS:******0000
BRAKE:***"**0000

ADJUST WHILE PRESSING SERVICE SWITCH. TO EXIT, TURN OFF TEST SWITCH. SS

screen will be displayed on the monitor.

  • Press the service switch to reset all values to 0000
  • Fully depress and release the accelerator, then the brake, then turn the steering wheel fully left and right.
  • Slide the test switch "OFF" to return to normal game mode.
  • If the above initialization does not perform correctly, repeat two or three times.

Page 21

Page 27
  • MAINTENANCE
DANGER:
DANGER: In order to prevent injury or electric shock to service personnel, ensure that the MAIN POWER IS OFF before attempting any maintenance.

Before performing any work not described in this manual, be sure to contact your distributor first to receive instructions or answers to questions.

(NOTE:

NOTE:

Ne This machine has a moving mechanism, and uses a drive castor in the base assy (see section 6-7, "Under Base Assy"). When the castor wears out, the seat assembly can be moved left to right easily by hand. Turn OFF the motor power switch in the base assy and secure the movable seat assy using the shipping brackets until the castor has been replaced with a new one. (Refer to section 6-9, "Handling Drive Castor Wear".)

As the drive castor wears, worn material is deposited in the base assy and should be removed approximately once a month. (Refer to section 6-1, "Cleaning the Under Base.) )

6-1 Cleaning the Under Base

The worn material from the drive castor should be removed once a month.

  • Switch the power OFF
  • [ifeterto secon 6:71 foment (Ri ‘efer to section 6-7-1,]"Removing the Rear Covers (L), (R)")
  • Move the seat assy by hand, and use a vacuum cleaner to remove the worn material that has collected under the roller.|(Refer to section 6-7, |'Under Base Assy".)

\\ notaroaze

Page 22

Page 28

6-2. Sign Assembly

6-2-1. Replacing the Fluorescent Tube and Reflector Lamp

Remove the two security screws (M5x12) and remove the acrylic retainer (B).

  • Remove the four Security screws (M5x12) and remove the acrylic retainer (C). Pull the acrylic sign forward to remove it. Replace the fluorescent lamp 4ft.. ) Unscrew the reflector lamp (240v 25w E14 only) to the left to remove. Refit by screwing the lamp to the right. (Warning: Make sure the lamp is not hot BL

Security screw(MS5 x 12)

Acrylic retainer (C) Fluorescent lamp

Acrylic sign Reflector lamp

Acrylic retainer (B) Security screw(M5 x 12)

before touching it.)

6-2-2. Replacing the LED Drive PCB

  • Remove the four Side box Security screw (M6x16) security screws (M6x16), and remove the sign board.
  • Disconnect the connector.
  • Carefully close the support locking ramp with pliers, and gently remove the board from each support in turn. Replace the board by pushing Locking support gently pushing the

board on to eachyion board

support.

Connector LED drive PCB

a

Page 23

Page 29

6-3. Main tower Assy.

6-3-1. Replacing Fluorescent Lamp and Reflector Lamp

  • Remove the four security screws (M5x12) and the acrylic support bar, then remove the acrylic board.
  • Replace the fluorescent lamp (12").
  • Unscrew the reflector lamp ( 240v 25w E14 only) to the left to remove. Refit by screwing the lamp to the right. (Warning: Make sure the lamp is not hot before touching it.)

Acrylic support bar Reflector lamp

Acrylic board

Fluorescent lamp

6-3-2. Removing the Game PCB

  • Remove the rear cover (L).
  • Disconnect the two connectors on the EMI board. Remove the six pozi head screws (M4x10) to remove the shield case door and earth terminal, being very careful of the connector that connects the EMI board and Game PCB, then remove the Game PCB.
Note: Be careful not to lose the internal washer (M4).

EMI board

Rear cover (L)

Game PCB

Ground terminal Pozi Hd Screw (M4x10) Internal washer (M4)

Page 24

Page 30

6-3-3. Removing the Shield Case

  • Remove the rear cover (L).
  • Remove the Pozi head screw (M4x10), and remove the earth terminal. (Note: Be careful not to lose the internal washer (M4).
  • Disconnect the two connectors on the EMI board, the AC fan connector, and the four connectors on the I/O PCB.
  • Remove the two Pozi head screws (M5x12), then remove the shield case.

6-3-4. Removing the I/O Board

  • Pull out the shield case until the I/O board can be seen. (Refer to section 6-3-3, above, "Removing the Shield Case".)
  • Remove the four Pozi head screws (M3x20). (Note: Be careful not to lose the four nylon spacers.
  • Remove the I/O PCB.

Shield case AC tan

Rear cover (L) Nylon spacer

EMI board

Pozi Hd Screw (M3x20

f Cup screw (M4 x 10)

Ground terminal

internal washer

Pozi Hd Screw (M5x12)

Page 25

Page 31

6-3-5 Replacing the Switch Mode Power Supply and Fuses.

  • Remove six security screws (M5x12), and remove the upper rear panel from the tower unit.
  • Partially slide the power supply wooden tray backwards to gain access to the fuses.
  • Disconnect all connectors, and remove the wooden tray completely.
  • Replace the power supply assembly.

6-3-6 Replacing the Amplifier.

  • Remove six security screws (M5x12), and remove the upper rear panel from the tower unit.
  • Partially slide the amplifier wooden tray backwards.
  • Disconnect all connectors from the amplifier, and remove the wooden tray completely.
  • Replace the amplifier.

Page 26

Page 32

6-4. Removing the Monitor

DANGER: _ There are areas within the monitor that have high temperature and vet high voltage even after the power has been removed. Extreme care must be taken to avoid burns or electric shock.
DANGER: _ The monitor weighs approx 60kg, at least two people should be used tt remove the monitors.

Ensure that the power is turned OFF before removing the monitors. Remove the back door from the monitor. Disconnect the six way video connector and three way power connector. Remove the hex head screw (M4x10) retaining the earth terminal. Remove the six security screws (M5x12) on the rear of the main tower assy, and remove the rear cover (U). Remove the wiring leading from the main tower to the monitor assy. Remove the four security screws (M5x12) on the front of the main tower assy, and remove the acrylic fastener bar and acrylic sheet. The monitor is fastened on the side and bottom to the main tower assy. Remove the following bolts: Side: Five hex head bolts (M8x45), flat and safety washers. Bottom: Two hex head bolts (M8x25), flat and safety washers.

WARNING: _ If the seat assemblies are not fitted to the tower and only one monitor is being removed, the tower assembly will be unstable, so remove both monitor assemblies.

Security Screw (M5x12) Acrylic fastener bar Rear cover (U)

Security Screw (M5x12)

Acrylic sheet

Main tower Assy

Page 33
  • Remove the four security screws (M5x20) connecting the monitor mask to the monitor cover.
  • Remove the six security screws (M5x20) which fasten the monitor mask to the monitor box, and remove the monitor mask.
  • Remove the three security screws (M5x20) which fasten the monitor cover to the monitor box, and remove the monitor cover.
  • Remove the four hex head bolts (M8x20), and withdraw the monitor from the front.
Note: Remember the monitor is heavy, approx 40kg, use two people.

Security Screw (M5x20) Monitor mask Monitor cover Hexagonal bolt (M8 x 40) Security Screw (M5x20)

Monitor box Monitor Security Screw (M5x20)

Page 28

Page 34

6-5. Steering and Shift Lever

6-5-1. Replacing the Steering Wheel

  • Remove the three security screws (M6x20), and remove the steering wheel.
  • When refitting the steering wheel, ensure that the keyway between the steering boss and shaft is at the bottom, and take care that the wheel is fitted at the correct angle.

6-5-2. Shift Assembly Maintenance

  • Removing the Shift assembly a). Remove the four security screws (M6x16), and withdraw the shift assembly.

Keyway (= Security Screw (M6 x 16)

Shift Assy

Security screw (M4 x 15) Steering wheel Connector

b). Disconnect the connector.

  • Replacing the Microswitch Remove the two pozi head screws (M3x16), and replace the switch. Ensure that the swith is refitted the correct way round. Pozi head screw (M3x16)

Microswitch Shift assy

Page 35

6-5-3. Replacing the Steering Drive PCB

  • Remove the shift assemble] (Refer to section 6-5-2,|"Shift Assy Maintenance".)
  • Remove the six security screws (M5x12), and slide the inner panel towards the steering wheel.
  • Remove the two security screws (M5x12) and the two security screws (M5x20), and remove the nose cover. (To remove the M5x20 security screws, push the seat assembly fully to the left and right.

(Refer to section 6-7-1, Removing the Rear Covers (L), (R)")

Security screw (M5x20) Security screw (M5x12) i ae ae

Inner panel

Nose cover \ Security screw (M5x12)

  • Remove the nose cover, then disconnect the four connectors on the PCB.
  • Remove the four nuts (M4), and remove the PCB complete with it's base.
  • Remove the four pozi head screws (M3x10), and remove the PCB from it's base. Steering drive PCB

Connector

Connectors

PCB base nut (M4)

Page 36

6-5-4. Replacing the Timing Belt

  • Remove the nose cover| (Refer to section 6-5-3, |"Replacing the Steering Drive PCB.)
  • Remove the steering wheel.|(Refer to section 6-5-1,)"Replacing the steering wheel".)
  • Remove the lamp/switch assemblies from the view change and motion stop buttons, and remove the inner panel.
  • Remove the four hex head bolts (M6x16) and three security screws (M6x16), and remove the front panel.

Front panel

Microswitch

er View change switch Security screw (M6 x 16) Hexagonal bolt (M6 x 16)

  • After removing the front panel, remove the locking nut (M6), and loosen the socket head bolt (M6x25) and four hex head bolts (M8x16). Slide the motor towards the steering and remove the timing belt.

. a Steering pulley Steering motor Motor pulley Connector Motor plate

Locking nut (M6) Timing belt

Whiz nut (M5}

Socket head (M6 x 25) Hexagonal bolt (M8 x 16)

Page 31

Page 37
  • When replacing the timing belt, fit to the motor gear first. If the belt is forced, it could damage the belt or motor.
  • Set the belt tension using the socket head bolt (M6x25). The tension should be set so that the belt moves about 2-3mm when a force of 500g is applied to the belt between the pulleys. (The tension of the belt is 7-9kg.)

500g 2~ 3am

  • After setting the tension, tighten the locking nut (M6), to prevent the socket head bolt (M6x25) from moving, and the four hex head bolts (M8x16).

6-5-5. Replacing the Motor and Motor Brush

  • Replacing the Motor
  • Remove the timing belt] (Refer to section 6-5-4, |'Replacing the Timing Belt".)
  • Remove the locking nut (M6), the socket head bolt (M6x25), and the four hex head bolts (M8x16). Disconnect the connector and remove the motor.
  • Remove the four Whizz nuts (M5), and remove the motor from the mounting plate.
  • Replacing the Motor Brush
  • Remove the motor . (See steps a and b of replacing the motor.)
  • Remove the brush cover by sliding it towards the back of the motor. Replace the brush and cap.
Note: When replacing the brush, ensure that the brush slides in to the motor without binding.

Motor brush

Cover

Page 38

6-5-6 Replacing the Pulley

The pulley is retained to the motor shaft with a 'Taper-Lock' bush.

  • Removing the pulley
  • Using a hex wrench, slacken the two grub screws a number of turns.
  • Remove one of the grub screws and screw it into the release hole. Continue to tighten until the 'Taper-Bush' releases.
  • Remove the pulley taking care not to lose the woodruff key.
  • Refitting the Pulley
  • Fit the pulley onto the motor shaft until it is flush with the end of the shaft, ensuring that the woodruff key is fitted.
  • Using a hex wrench, alternately tighten the two grub screws in the fix holes until tight.

Release Hole

Fix Holes.

Motor Shaft ‘Taper-Lock' Bush

Pulley

Page 33

Page 39

6-5-7. Replacing the Fuse

There is a fuse located below and to the left of the steering wheel. Use a flat blade screwdriver and turn the fuse cap anticlockwise to release the cap and fuse. Replace the fuse (Samp Slo-Blo)

[

N_ Fuse holder (cover)

6-5-8. Replacing the Control Pot

  • Remove the six security screws (M5x20), and remove the rear cover of the upper base assembly.
  • Disconnect the connector located below the control pot.
  • Loosen the control shaft screw and remove the control and control stopper.
  • Remove the control from the control stopper.
NOTE: Replace only with a continuous rotation pot (Part No. X008-022)

Control shaft screw

Page 34

Page 40

6-6. Replacing the Seat

6-6-1. Removing the Seat

  • Remove ten security screws (M5x10), and remove the headrest.
  • Loosen the security screws (M5x20) on seat side A, seat side B, and seat back A joints (six screws total). When doing this, take care to remove the screws completely.
  • Remove the ten security screws (M5x25), and remove seat side A, seat side B, and seat back A. When doing this, take care not to lose the washers for each screw.

Headrest Security screw (M5 x 20)

Seat back A Security screw M5 x 20)

Seat washer (B) (rubber)

Seat washer

Security screw (M5 x 25)

(M5 x 20)

Security screw (M5 x 20) Seat side A — (Opposite side: Seat side B) Seat washer (B) (rubber)

Page 35

Page 41
  • Remove the four pozi head screws (M5x25), and remove the speaker

Pozi head (M5 x 25)

Speaker cover

\_ Seat washer

cover.

  • Remove the two pozi head screws (M5x25) and four security screws

Seat stay lL

Seat washer

i -=8

\Pozi head (M5 x 25)

security screw(M8 x 20) ‘0 a Washer(M10)_~ ag

(M8x20), and remove the seat section.

Page 36

Page 42
  • Remove the two security screws (M5x25) and two Whizz nuts (M5) from the upper part of the removed seat section, and remove the seat stay from the seat.
  • When doing this, take care not to lose the washers.

Security screw (M5x25) Seat washer

Si

n

Seat stay —s na

\ Seat washer

Whizz nut (M5)

6-6-2. Installing the Seat

  • Temporarily fasten the seat stay to the seat (Refer to 6-6-1, step 6).
  • Install the seat section to the seat.
  • Temporarily fasten the seat to the seat holder, and the seat stay to the rear board.
  • Secure the seat making sure that the seat line is parallel with the seat holder.
  • Tighten all of the screws in the seat and seat stay.
  • Install the speaker cover.
  • Install seat side A, seat side B, seat back A, and the headrest, following the reverse procedure of section 6-6-1 steps 1-3.

Seat line

Holder line

Page 43

6-7. Under Base Assembly

DANGER: The drum drive PCB|(see section 6-7-2,|"Names of Under Base Parts") has areas of high voltage and high temperature even after the power has been turned OFF. Take care not to touch the PCB to avoid receiving electric shocks or burns.
DANGER: Ensure that the power is turned OFF before commencing work.
WARNING: This work involves moving the seat assembly from left to right in order to remove screws. Take care not to trap or injure the other person when performing this work.

6-7-1. Removing the Rear Covers (L), (R)

Removing the Rear Cover (L)

4) Remove the rear guard fence.

Turn the steering wheel all the way to the right, and move the cabinet by hand so that the rear cover (L) is easier to remove.

Remove the security screws (M5x20), and remove the edge guards and rubber skirts.

Remove the nine security screws (M5x12) and two security screws (M8x20), then remove the rear cover (L)

Removing the Rear Cover (R)

1)

Security screw (M5 x 20): / Turn the steering wheel all the way to the left and move the cabinet to the left by hand so that the rear cover (R) is easier to remove. Rear cover (R)

Remove the rear cover (R) in the same way as the rear cover (L) as above.

Rear cover (L) Edge guard Security screw(M8 x 20) Rubber skirt Security screw (MS x 12)

Page 38

Page 44

6-7-2. Names of Under Base Parts

Castor unit Rollerbase Roller Beam V belt

Rubber cap A

Motor

  • ~~ Motor brush

Drum drive PCB

Motion stop PCB

5 Motor isolation switch Ls ETT Fuse Y i £ “\_ Rubber cap B

Shutter hanger Drive caster \ Link rod

6-7-3. Replacing the Drive Castor

NOTE: When replacing the castor, it is recommended that two people perform the work and safety gloves are worn.

Removing the Castor Unit. Link rod Link arm

  • Remove the nut (M10), and remove the link rod and link arm.
  • Remove the Hex head bolt (M8x20), and remove the nut locking bracket from the link arm.
  • Use the nut locking bracket and turn the hexagonal nut until it touches the housing. washer (Mio) Safetywasher (Mio) \ Nut (M10) _ Hex head bolt (MB x 20} Link arm

Housing

Nut lock Hexagonal nut

Page 45
  • Loosen the four hex head bolts (M10x40) that hold the Hex head bolts (M10x40) housing to the main housing.
  • The housing is fixed using keyholes. Lift the housing up and then pull it forward to remove the castor unit. If there is difficulty in removing the unit, remove the top two bolts.
  • | Remove the nut (M20), pull out the shaft and replace the drive castor.
  • When replacing the drive castor, ensure that the shaft key aligns with the keyway in the housing.
  • Tighten the nut (M20) so that there is no play between the drive castor and housing. Take care not to tighten the nut too tight, or the castor will not turn freely.
  • Re-tighten the four hex head bolts (M10x40) to a torque of 70 ft/lb

Nut (M20) Caster unit Washer Castor case

Keyhole

Hex head bolt (M10 x 40) Drive castor

Page 40

Page 46
  • Notes on Installing the Castor Unit

a)

Spacer section Install the castor unit in the roller base, and tighten the four hex head bolts (M10x30).

Use the nut locking bracket to turn the nut towards the link arm and set the spacing between the nut and housing as shown in fig A. This space should be set so that the nut just grips the spacer section of the locking bracket to the housing as shown in fig B.

Refit the nut locking bracket using the hex head bolt (M8x20).

Connect the link rod and link arm. Ensure this is done as shown in fig C.

Note The steering will not work properly if the direction is incorrect.

Refit the rear covers (L) and (R), and rear safety fence.

Nut lock

Handle side

Figure B

Page 41 Oy

co Figure A

Link rod

Drive castor side

Figure C

Page 47

6-7-4.

Switch connector Replacing the Drum Drive PCB and Motion Stop PCB

Remove the rear cover | (Refer to section 6-7-1, |'Removing the Rear Cover.)

Disconnect all the connectors

Remove the Pozi head screws (M3X10) and washers, and remove the PCB.

Motor connector

M3 Pozi head screw,

Drum drive PCB

Motion stop

Page 42

Page 48

6-7-5. Replacing the V Belts

  • Removing the V Belts

a)

b) Remove the rear covers (L), (R).|(Refer to section 6-7-1,|"Removing the Rear Covers".) Remove the four bolts (M8x20) and the four security screws (M8x40), then remove the beam] See section 67-2, Names of Under Base Parts" page 37.) Loosen the four hex head bolts (M8x20). Remove the locking nut (M10). Remove rubber cap A, and remove the tension bolt (M10x60) and washer. Push the motor to the right as shown, and remove the two V belts.

Tension bolt (M10 x 60) V belts Pulleys Washer

  • Installing the V Belts

Place the two V belts on the pulleys. Attach the tension bolt (M10x60) and washer. Adjust the tension of the V belts by tightening the tension bolt. The belts should be adjusted so that they have about 5- 6mm of slack when the centre of the belts are depressed with a force = of 2kg. Tighten the locking nut (M10). (The tension in the belt is 19-21kg.) Refit the beam, and tighten the four bolts (M8x20), and four security screws (M8x40). Replace rubber cap A.

Page 43

Page 49

6-7-6. Replacing the Motor and Motor Brushes.

  • Replacing the Motor Brush.
  • Remove the rear cover (Refer to section 6-7-1, | Removing the Rear Covers".)
  • Remove the pozi head screws from the brush covers (located either side of the motor), and remove the covers
  • Replace the two brushes. (Ensure that the brushes slide freely into the motor when replacing.)
  • Replacing the Motor
  • Remove the two V belts|(Refer to section 6-7-5, |"Removing the V Belts".)
  • Disconnect the motor c 7
  • Remove the motor with the slider bracket attached.
  • Remove the four nuts (M10), and remove the motor from the slider bracket. e) When installing the motor, adjust the V belts as described in|section 6-7-5, "Installing the V Belts".

Motor brushes

Motor connector

6-7-7. Replacing the Motor Fuse

The fuse is located as shown in section 6-7-2,|page 37.

  • Remove the rubber cap B.
  • Turn the fuse cap anticlockwise half a turn, and remove the cap and fuse.
  • Replace the fuse (5A, Slo-Blo).

Page 44

Page 50

6-8. AB Pedal Assembly

6-8-1. Removing the AB Pedal Assembly

  • Remove the four security screws (M6x20), and withdraw the assembly forward.
  • Disconnect the connector, and remove the assembly.

Security screw (M6 x20)

AB pedal Assy

6-8-2. Replacing the Control Pots

  • Loosen the quadrant gear clamp screw, and remove the quadrant gear.
  • Loosen the gear grub screw, and remove the gear.
  • Replace the control pot.
Note: When replacing the control pot a. Ensure that the potentiometer locating tag is engaged in the mounting plate hole. b. Turn the potentiometer shaft almost fully clockwise before engaging the quadrant gear.

~ ph —— Grub screw Control pot \

Quadrant gear

Clamp screw

Page 45

Page 51

6-9. Handling Drive Castor Wear

This machine uses a moveable mechanism controlled by the pressing of a drive castor against the metal roller. During the playing of the game, this castor gradually wears due to the constant friction with the roller. When the drive castor wears sufficiently, the pressure becomes poor, and the seat assembly is no longer driven left and right and can be pushed easily sideways by hand. This will take about a year to occur. (This is assuming that the game is played 7.5 hours per day. This period will vary depending on how often and for how long the game is played.

6-9-1. Checking Drive Castor Wear

The drive castor should be checked, when the machine displays the following symptoms. + Game play is possible on the screen, but the seat assembly does not move. + When the steering wheel is turned to the left or right, the seat assembly movement is slow.

NOTE: First check that the motor is working.

If the motor is not working, ensure that the motor switch in the under base is turned ON. If the motor switch is ON but the motor is not working , there is a motor problem, and should be checked as described in section 7, "Troubleshooting".

Method of Checking

  • Ensure that the power to the machine is turn,
  • Remove the fence, and rear cover (L) or (R)| (Refer to section 6-7-1, "Removing the Rear Covers (L), (R)" on pag 5
  • Look at the drive castor in the roller base. If the drive castor moves left and right when the steering wheel is turned, there is no problem with the steering linkage, and the problem is the drive castor worn out.

6-9-2. Action When the Drive Castor is Worn Out

If the drive castor is worn out, discontinue use of the machine until the following has been carried out.

  • Turn the main power to the machine OFF.
  • Remove the fence.
  • Remove the rear cover (L)| (Refer to section 6-7-1, |'Removing the Rear Covers".)
  • Turn the motor switch in the under base OFF.
  • Refit rear cover (L).
  • Refit and securely fasten the seat assembly shipping brackets that were removed when the machine was first installed.
  • Refit the fence.
  • After the above has been carried out, turn the main power to the machine ON.
  • After a new drive castor has been fit le is reinitialized before the game is played| (Refer to section 6-7-1, |"Removing the Rear Covers" "Replacing the Drive Castor”, and 5-5, "Adjustments When Replacing Parts".)
  • After fitting the new drive castor, remember to turn the motor switch ON.

Page 46

Page 52
  • TROUBLESHOOTING

any checks or adjustments. (eer To avoid injury, always turn the main power OFF, before carrying “|

Check the following whenever there is a problem with the machine.

1) The machine is requires a mains supply of 220-240volt AC. If there are several high current devices (air conditioners, large rides or other large machines etc.) connected to the same power supply, the power supply may fluctuate due to power surges, and cause game malfunction. Each machine requires a maximum of 8amps, Ensure an adequate power supply to prevent an overload and possible fire risk.

If the machine fails to work even though the power is ON, try turning the power off and back on. If the machine still fails to work, check the mains in fuse.

If the seat assembly does not move even though game play is possible on the screen, check that the seat shipping brackets have been removed, the motor switch in the under base is turned on, and the condition of the drive castor. Check the drive castor according to[section 6-9, |Handling the Drive Castor Wear" (page 44).

The game will not operate correctly if it has not been initialized after replacing the game PCB, ROM, or control pots. Adjustment should be performed according to| section 5-5, [Adjustment After Replacing Parts" (page 21).

Check all wiring for loose connections.

Dirt and dust on the game PCB, steering PCB, drum motor drive PCB, or monitor PCB, could cause a malfunction, so all PCB's should be kept clean.

When checking electrical problems, refer to the wiring diagrams, and make sure that the connectors and wire colours are correct.

If none of the items 1-7 above seem to be the cause of the problem, or the problem is not cured, contact your dealer.

Repairs to the PCB should be carried out by your dealer. NEVER perform a continuity check on the PCB with a test meter, as the internal voltage of the meter could cause damage to PCB components.

When sending a part for repair, clearly describe the problem and ensure that the part is properly packed in a sturdy container to prevent damage in transit.

Page 47

Page 53

gy obea 8.

PARTS

ITEM DESCRIPTION PART No.

Bid|M6 FULL NUT27000021
B7_|M6x20 HEX HEAD SET SCREW - BZP88300700

M6 FLAT WASHER H/DUTY -BZP 88300702 M6 SPRING WASHER TYPE B - BZP 28000034

39| SWIVEL CASTOR - 63mm59000002
38| ADJUSTABLE FOOT M20x125 W/LOCK NUT25000008
15| TOWER PLINTH45000300
19|LocriTE 24295000009

x4

© O-c ‘SPRING WASHER

FLAT WASHER, com

° °

iG

io lO LOCTITE !!

Page 54

6p ebea

ITEM DESCRIPTION PART No. | QNTY

BI2__[Mfx25 SECURITY BUTTON HEAD - SUS2es00042 |20
MS FLAT WASHER - SUS2000030 |20
MS SPRING WASHER TYPE B - SUS2s000017[20
B9 _ |Max25 HEX HEAD SET SCREW - BZP26300050 |8
MS FLAT WASHER H/DUTY - BZP38300702 |8
MS SPRING WASHER TYPE B - BZP2000027[8
B3__[MSx12PZ PAN HEAD SCREW - BZPaosonase | 4
MS FLAT WASHER H/DUTY - BZPsss00432 |4
MS SPRING WASHER TYPE B - BZP28000026 |4
21 __ [COIN TOWER INTERNAL SUPPORT BRACKET45000306 |1
19[Locrime 24295000009
17__[TOWER SIDE SUPPORT RHS45000302 |1
16 _ | TOWER SIDE SUPPORT LHS5000301 |1
12__[PCB STOP BRACKET5000299[1
11__[SHORTY BUSHING39000051[12

10 _ [EXTRUDED GROMMETING 39000807

1 __ [TOWER CENTRE SECTIONaso00288 |1

SPRING WASHER

FLAT WASER PCB Assy (2)

Page 55

os obea

SEEPAGES GAS)

Page 56

obea

Ts 1TEM DESCRIPTION PART No. | QNTY

3_|SESLAMP HOLDEReasooo0s[4
2_|240v 25w SES SILVERED LAMP.eaooooss[4
Bit[32:95 RIVETaon[4
BS_[MSx12 SECURITY BUTTON HEAD SCREW - SUS,2axoooas[a
3 _[MSx12 HEX HEAD SET SCREW - BZ?250032[4
MS FLAT WASHER HIDUTY - BZPwanna[4
MS SPRING WASHER TYPE B - BZP2aoooa2s[4
2 _ [Nox s* PZ PAN HEAD SCREW - BZPaso |8
“47[COIN TOWER SAFETY DECALsoooos[2
46| YELLOWCAR DECALsoonft
45[GREEN CAR DECAL000202[1
44[BLUE CAR DECAL-so000203[1
43[REDCAR DECAL,so000204|
40[FLUORESCENT TUBE ASSEMBLY1
FLUORESCENT ASSY WOODsrioooat|
12"TWIN LIGHTING TRAYeasoooss[1
12" SW FLUORESCENT TUBE,easoo00s[2
39_[Ma WING NUT-BzP200029|S

29__ [SERIAL NUMBER PLATE =.

28[CECOMPLIANCE LABELao]at
20 _ | TOWER PLINTH FRONT CENTRE CLOSING PLATE,soos|
19[Locrire 24295000009)
14[CENTRE ACRYLIC“sao00008|
11[CENTRE ACRYLIC TOP RETAING BRACKETsoon[a
10[RACE START LAMP MNTG BRKT - LHSso00296|
9[RACE START LAMP MING BRKT-RHS5000297|

BS) a2.

Page 57

obea zs

ITEM DESCRIPTION PART No.

B10|M8x45 HEX HEAD SET SCREW - BZP26500435

M8 FLAT WASHER H/DUTY 88300702

BO|M8x25 HEX HEAD SET SCREW - BZP25300050

M8 SPRING WASHER TYPE B - BZP 38000027

BS|MSx12 SECURITY BUTTON HEAD SCREW - SUS26300045
B4| MS5x16 SECURITY BUTTON HEAD SCREW - SUS26300032

MS NYLOC NUT - BZP 27000148,

28| WASHER - BZP45000323
27| TOWER/BASE SEAT JOINT BRKT - LHS45000307
26| TOWER/BASE SEAT JOINT BRKT - RHS.45000308
25| TOWER/BASE JOINT RUBBER45000310
24| TOWER/BASE SEAT JOINT BRACKET PLATE45000309,

‘SPRING WASHER LAT WASHER

@® ~— Rp

Je

Page 58

obea

€s SPRING WASHER

ITEM DESCRIPTION PART No. | QNTY

EL[SCHAFFNER IEC MAINS INLET(960000431
E2_[MAINS SWITCH - DPOLE1600000001
E3_[MAINS FILTER624000011
E13[LINK PCB ASSEMBLYXAD-LINK PCB |1
BI|M3x12 POZI PAN HEAD SCREW - BZP263001332
82 _ |Mox16 POZI PAN HEAD SCREW - BZP3883007908
M6 FLAT WASHER H/DUTY - BZP280000378
M6 SPRING WASHER TYPE B - BZP280000348
83|Max12 POZI PAN HEAD SCREW - BZP263000576
Md FLAT WASHER H/DUTY - BZP280000364
Md SPRING WASHER TYPE B - BZP280000356
BA|MSx12 SECURITY BUTTON HEAD SCREW263000452
19[LOCTITE 24295000009
1[TRANSFORMER TRAY450003131
2 _ [LINK PCB COVER BRKT450003701
3_| TRANSFORMER 0-220--240/0-100 @ 5A,677000132
4[M3 NYLOc NUT270000262
SCHAFFNER BOOT(60000171

t

FLAT WASHER _ 20 SPRING WASHER

Page 59

obea

vs

ITEM DESCRIPTION PART No | QNTY

B1|M4x12 POZI PAN HEAD SCREW - BZP263003832
B2|M4 SPRING WASHER TYPE B - BZP280000182
B3_|M4x30 SLOTLESS HEAD SCREW - BZP26500185,2
B4__|M4 WING NUT - BZP270001292
19|LOCTITE 24295000009
6COIN ENTRY BLANKING PLATE21000055,1
5“CREDIT AVAILABLE WHEN LIT" BUTTON ASSY602002152
4PUBLIC INFORMATION DECAL420000061
3SERVICE BRACKET ASSEMBLYsoroeee1
2DOUBLE FRAME MINI DOOR - CASHFLOW655003771
1|COIN TOWER450002891
Page 60

obea ss

ITEM DESCRIPTION PART No 7 _ [M6x20 HEX HEAD SET SCREW - BZOP 26300778 M6 FLAT WASHER HIDUTY - BZP 28000037 M6 SPRING WASHER TYPE B - BZP 2s000034 BS_[MSx12 SECURITY BUTTON HEAD SCREW - SUS 26300085 3 _ [M520 HEX HEAD SET SCREW - BZP 88300796 MS FLAT WASHER HIDUTY - BZP 88300789 MS SPRING WASHER TYPE B - BZP 28000026

19[LocrimE 24295000009

16 _ [FLOURESCENT TUBE ASSY MNTG BRKT 45000333,

14_[POSITION BOX MOUNTING BRKT - RHS45000332
13__[POSITION BOX MOUNTING BRKT - LHS45000331

10 _ [TOP EXTERNAL CABLE COVER BRKT 45000330 1 _ [MAIN HEADER WOODEN BOX 37100039 FLAT WASHER SPRING WASHER

FLAT WASHER’ SPRING WASHER. Pe

Page 61

obea 9s

ITEMDESCRIPTIONPART No.| QNTY
ES[4 FLUORESCENT TUBE ASSYsoos[a
2_[MESLAMP HOLDEReawo0003 |6
EL_|240v 25w SES SILVERED LAMPeaooo08s |6
Ba_[M5x20 HEX HEAD SET SCREW - BZPsea007% |4
B3_[MSx16 HEX HEAD SET SCREW - BZP26500431|2
MS FLATT WASHER HIDUTY - BZPasxoo7e |6
MS SPRINGWASHER TYPE B - BZPasoo002s |6
BI_[Nox 1" PZ PAN HEAD SCREW - BZPaei0007 |12
19[LocrmmE 2295000009
9__[LEADER LAMP MOUNTING BRACKET5000329|2
Page 62

obea us (an) a2,

ITEM DESCRIPTION PART No B12_]M5x10 SECURITY BUTTON HEAD SCREW - SUS 26300043 B6 | M6x16 SECURITY BUTTON HEAD SCREW - SUS 26300044

32| SEVEN SEGMENT DISPLY FILTER,39000048,
23| POSITION VAC-FORM CAR STICKER - GREEN40000210
22| POSITION VAC-FORM CAR STICKER - YELLOW40000211
23| POSITION VAC-FORM CAR STICKER - BLUE40000212
22| POSITION VAC-FORM CAR STICKER - RED40000213
19|LOCTITE 24295000009
15| POSITION VAC-FORM MOUNTING WOOD37100040
3| POSITION VAC-FORM45000325
2| POSITION BOARD MOUNTING BOX45000324
Page 63

obea 8s

ITEM DESCRIPTION PART B6 | M6x20 SECURITY BUTTON HEAD SCREW - SUS 263009

BS|MSx12 SECURITY BUTTON HEAD SCREW - SUS263000¢
19|LOCTITE 242950000
8| TOP FLASH ACRYLIC RETAINING BRKT - TOP4500037
7|TOP FLASH ACRYLIC RETAINING BRKT - BOTTOM4500037
6| TOP FLASH ACRYLIC RETAINING BRKT - BOTTOM4500037

4 | TOP FLASH ACRYLIC - GREEN/YELLOW A | 3000002 TOP FLASH ACRYLIC - RED/BLUE. 3000002

Page 64

obea 6s

TEN DESCRIPTION PARTNo, | ONT

B5__[NowaPZFLANGE SCREWaeioonrs|16
Bi_|Miao HEX EAD SET SCREW —BZP2es0088|12
WMS FLAT WASHER HIDUTY _BZPwws0070|12
MN SPRING WASHER TYPE B-BZPsooo?fia
9frocrmeze‘9so00009
MONITOR CABINET SIDE DECAL -LHScwoonso7 |1
°MONITOR CABINET SIDE DECAL - RHS400002081
7_[MONITOR TOP SUPPORT BRACKETsoon|2
@_[TUBE MOUNTING WOOD SIDE SUPPORT LAS~so00320|2
3_[TUBE MOUNTING WOOD SIDE SUPPORT_RIScsoons21|2
7_[MONITOR WOODEN CABINET-LHSsrio002[1
3_[MontTor WOODEN CABINET-RHSsrio008[1

FLAT WASHER

SPRING WASHER © pif

Page 65

obea

ITEM DESCRIPTION PART No. | QNTY

1|MAIN BASE METALWORK450002241
25|SWIVEL CASTOR 75mm.590000056
26| ADJUSTABLE FOOT M20x100mm W/LOCK NUT.250000086
B7_|M8x20 HEX HEAD SET SCREW - BZP88300700 |24
M8 FLAT WASHER H/DUTY - BZP28000027 |24
MB SPRING WASHER TYPE B - BZP88300702 |24
38|LOCTITE 26295000003-

M20 Locking Nut to be fitted to foot before foot is fitted.

On @ 8 Spring Washer

MB Flat Washer

Page 66

obea TEM DESCRIPTION PART No. [ONT

1 _ [DRIVE MOTOR & GEARBOX‘sooo|
1B6__|Mix16 HEX HEAD SET SCREW -BZPwesooTes|
B12[MB SPRING WASHER TYPE B- BZPaaooooa7 | 7

BIS | M820 HEX HEAD SET SCREW - RZ waar | a Bia _| MIO FULL NUT 125 PITCH -BzP aronore7 | 1

BIT_|MiOFLAT WASHERHIDUTY - BZPwes00704[2

319 _ [MIO SPRING WASHER TYPE B-BZP aannon2s | 1

@_|MoTOR DRIVE DRUMisoo0ss|
&_[DRIVE SHAFTasa|
9 _ DRIVE MOTOR MOUNTING BRACKETsoon|
Tr[FRONT CONTROL ARM‘soos|
12 _ [REAR CONTROL ARMwso002s2[1
T3_[TAPER LOCK BUSHING - 25mmas000156 | 1
Ta[WASHER 40xi5x3.2-RZPaso0003s|S
15 _ [DUAL V BELT PULLEY BLOCKas0002s7|
To| TAPER LOCK BUSHING - 518wsu00s7|
22_| WOODRUFF KEY actowsooarse | 2
23_[WOODRUFF KEY x7515000238

28_|RIGHT ANGLE DUAL BALL JOINT ASSY is00276

MiOx48 THREADED STUD -BZPaesnon7|
[MIO THIN FULLNUT- BZ?arooo02s[2

29 _ [PILLOW BEARING -FYH UCP Xo7 aso00036 | 2

730)_|PILLOW BEARING -FYH BLP 205wsoo0y | 2
a[WASHERiso00sy|
15 _ [WASHERisooon0[1
xe[LocriTE 22‘95000009,

45.313.00

Page 67

obea

TTEM DESCRIPTION PART No. | QNTY 7 _ [MSO HEX HEAD SET SCREW - BZP sexoo700 [

MS FLATWASHER HIDUTY - BZPwesoo7e2[4
MS SPRING WASHER TYPE B - BZPseso0027|
1810[MIOx80 HEX HEAD SET SCREW - BZP2es00a39|
BII_[M250 HEX HEAD SET SCREW - BZP2esooass[4
MI2 FLAT WASHER H.DUTY -BZP2xo00020|
MI2 SPRING WASHER TYPE B-BZP2ooo019|
B15[MIO FULL NUT. BZPrro00023|
B17[MIO FLATWASHER H/DUTY - BZPsexo0798[5
BIS[MIS FLAT WASHER HIDUTY - BZPzaooo02t[5
24[V DRIVE BELT aV-355sons[2
38[LOCTITE 28295000009
Page 68

obea €9 1TEM DESCRIPTION PART No. | QNTY

EI[DPCO TOGGLE SWITCHTBA.1
6 _ [20mm FUSE HOLDER - PANEL MOUNTTBA1
ES[20mm FUSE 5A SLO-BLO3500600[1
2 _ [MOTION STOP PCB450004821
EI[DRIVEMOTOR PCB1
B22[MIS FLAT WASHER H/DUTY - BZPzeooons[2
20[MIN SPRING WASHER TYPE B- BZPzeoooo2s |2
B16 _ [MIS FULL NUT 125 PITCH. BZP270002081

B12 |MISx30 HEX HEAD SET SCREW 125 ITCH. BZP | 26500818 [1

9 _ [Ml0xi0 HEX HEAD SET SCREW2osooas7[4
Mi0 FLAT WASHER - BZPsasoo7es |4

MIO SPRING WASHER TYPE B - BZP zeooon2s | 4

B3_[MSxI2 PZ PAN HEAD SCREW - BZP2e300s7s |16
MS FLAT WASHER H/DUTY - BZPzeoo0032 |16
MS SPRING WASHER TYPE B - BZPzeoo002s |16
82[Ma4xi2 POZI PAN HEAD SCREW - BZP20300057[8
Ma FLAT WASHER - BZP2eoo006 |8
Ma SPRING WASHER TYPE B - BZPzeooooas |8
Bi[Mi0xd0 HEX HEAD SET SCREW - BZPzoos?|2
M0 FLAT WASHER H/DUTY - BZPsasoo7es[2
MIO SPRING WASHER TYPE B - BZPzeooon2s |2
42[FUSELABELSA1
41[DRIVE MOTOR PCB MOUNTING BRACKET450002821
38[LOCTITE 24295000009
31[BLIND HOLE GROMMETasoo02a6 |2
27[MOUNTING PIVOT - THK RBI ISD3450002271
16[BALL JOINTISEAT BED LOCATING BRKT450002281
13__[SUS 304 ROLLER BRACKETsoos[3

a Wi

Page 69

p9 obea

ITEM DESCRIPTION PART No. | QNTY

B24|M8x40 SECURITY BUTTON HEAD SCREW - SUS263000474
B23.| M8x20 HEX HEAD SET SCREW - BZP883007004
M8 FLAT WASHER H/DUTY - BZP280000274
MB SPRING WASHER TYPE B - BZP883007024
B19| M10 FLAT WASHER H/DUTY - BZP883007941
B17| M10 SPRING WASHER TYPE B - BZP280000231
Bid| M10 FULL NUT 1.25 PITCH - BZP270001971
38| LOCTITE 24295000009
7|MAIN BASE CROSS MEMBER450002631

_*%6

Page 70

obea

$9

ITEM DESCRIPTION PART No. | QNTY

B23|M8x20 HEX HEAD SET SCREW - BZP883007004
M8 FLAT WASHER H/DUTY - BZP883007024
MB SPRING WASHER - BZP280001764
38| LOCTITE 24295000009
20| SHIPPING BRACKET - REAR450002642

2) M8 SPRING

WASHER i MS

SPRING bs WASHER M8 SPRING . WASHER M5 FLAT

Page 71

obea

ITEM DESCRIPTION PART No. | QNTY

BS—]M10x40 HEX HEAD SET SCREW - BZP265004372
M10 FLAT WASHER H/DUTY - BZP883007942
M10 SPRING WASHER TYPE B - BZP280000232
BI)MSx12 HEX HEAD SET SCREW - BZP265004328
MS FLAT WASHER H/DUTY - BZP883004328
MS SPRING WASHER TYPE B - BZP280000268
23|LOCTITE 26295000003
22[LOCTITE 24295000005
21| SIDE IMPACT BUMPER450002504
11[SUS 304 CASTOR ROLLER PLATE45000248,2
4[SEAT MOUNTING BRACKET450002491
1|MAIN HOUSING450002471

fone Ng ————~e \. / —©®

>

S

Page 72

obea

8 SPRING ° WASHER

1TEM DESCRIPTION PART No. [QNTY

87[10mm = CLIP5000365 |1
Ba[Micl0 HEX HEAD SET SCREW -BZP2es00a33 | 3
MN FLAT WASHER HIDUTY -BZPwesoo72[3
‘MN SPRING WASHER TYPE B - BZP2eooooa? |3
24[GREASELIGHT95000019

LOCTITE 242 {95000005

20[DELRINBUSH- SMALLs000262 |1
19_[DELRINBUSH- LARGEaso00261 |1
18[BEARING - NTN S106aso00260 |1
13 _ [NEOPRENE BUMPER5000259|_1
12_[TENSION SPRINGqsoo0as8 |1

6 _ | TENSION SPRING INSERT CAP. ‘as0002s4 | 1

5 _ [TENSION SPRING END CAP5000253 |1
3__[CASTOR MOUNTING BRACKET ASSEMBLYas000252 |1
2_[CASTOR SHAFTsoos |1

M8 FLAT WASHER

Page 73

obea 8 SPRING WASHER

wasn

TTEMDESCRIPTIONPART No.[QNTY
Bs _ [M820 HEX HEAD SET SCREW - BZPss300700|1
MS FLAT WASHER HIDUTY - BZPsss00702,1

MB SPRING WASHER TYPE B - BZP a

86 _ [MIO FULL NUT. BzPzoos|4
MIO FLAT WASHER HIDUTY - BZPws00788|4
M0 SPRING WASHER TYPE B- BZPasoo00234
2 _ | Maxi6 HEX HEAD SET SCREW - BZPsss00705|
Ml SPRING WASHER TYPE B - BZPasooo27[1
2(LOCTITE 2295000005
17__[WOODRUFF KEY &x7x40500234|a
15 _[DRIVE CASTORxio2056|1
Td| WASHER 40x8 5x32 - BZP5000235)
9__[ADIUSTING NUT LOCKING BRACKET50057 |a
& __ [ADIUSTING NUT M365000256|1
7[CONTROL ARM5000255|1

os

M8 SPRING WASHER ©

@9)

Page 74

obea

rere BS he apna oe

ITEMDESCRIPTIONPART No.| QNTY(22)
BS[M10x40 HEX HEAD SET SCREW - BZP265004374Ek
‘MIO FLAT WASHER H/DUTY - BZP883007944-
‘MIO SPRING WASHER TYPE B - BZP280000234
B3__[M8x20 HEX HEAD SET SCREW - BZP8830070024
‘M8 FLAT WASHER H/DUTY - BZP8830070224
‘M8 SPRING WASHER TYPE B - BZP2800002724
22|LOCTITE 24295000009
16]FIXED CASTOR 50mm - BLUE590000036
Page 75

obea

OL

19 |GREASE - LIGHT.95000019FIX TO MAIN FRAMEae

USING 2xM10 FLAT

16 UNIVERSAL JOINT NP-18-NOA-02450002711WASHER
1s | CONNECTING SHAFT TRANSMISSION GEAR,450002781AND 1xM10 HALF NUT
14 [LOWER ROD EYE- BLIOBDL,“450002771(AS PER OTHER END)

4 [STEERING POTENTIOMETER LOCATING BRKT | 45000268 [1 M6x40 HEX HD SET SCREW AND NYLOC NUT.

Page 76

obea

TL

ITEM DESCRIPTION PART No. | QNTY

B17[EXTERNAL CIRCLIP 32mm450002871
B6—[M8x20 HEX HEAD SET SCREW - BZP8830070016
M8 FLAT WASHER H/DUTY - BZP8830070216
‘MB SPRING WASHER TYPE B - BZP2800002716
45|GREASE - LIGHT95000019
44|LOCTITE 24295000009
30| FIXED CASTOR 50mm - BLACK59000008,4
18|ROLLER450002841
17[CASTOR SPACER450002852
16| WASHER450002861
7|SEAT BED ASSY - INCL. TURNED PART450002831
EVA FLOOR MAT - GREY450003361

EVA ADHESIVE, 92000030 eo M8 @—__ FLAT WASHER

M8

SPRING

WASHER

EVA MATTING TO

GLUED

TO UNDERSIDE

Page 77

obea am TEM DESCRIPTION PART No. | QNTY

BefLocrmme 24295000009,

B)_|Ml0x30 HEX HEAD SET SCREW - BZ 2s0n8es

MIO FLAT WASHER HIDUTY - RZPweo07m |2
MIO SPRING WASHER TYPEB-BZPaos |2
1a | MSxI6 HEX HEAD SET SCREW - BZP2esooaat[2

MS FLAT WASHER H/DUTY - BZ? HOE MS SPRING WASHER TYPEB-BZP 2000026

10]Moxi6 SECURITY BUTTON HEADSCREW-SuS| 200000 |3
M6 FLAT WASHER - SUSwaoeT |3
MG SPRING WASHER TYPE- SUSaon|S
Bi _| Mi0x0 HEX HEAD SET SCREW -SUSweooms |6
MIO FLAT WASHER SUSaos|e
MIO SPRING WASHER TYPE B SUSoea
BS_|Max35 SECURITY BUTTON HEAD SCREW-SuS| 26300000 |4
Ml FLAT WASHER - SUSamor|
‘Mi SPRING WASHER TYPE-SUSEnae]
2 | Mast6 HEX HEAD SET SCREW -BZPwoos|e
Ma FLAT WASHER H/DUTY - BZ?wesoom2|
Mi SPRING WASHER TYPER-BZPTeae]
BT _| Moxt6 HEX HEAD SET SCREW -BZPaesoosit|S
MG FLAT WASHER H/DUTY - BZ?oea
MG SPRING WASHER TYPE- BZPaeons|
3_|WASHER BZP‘somos|

20 _ | STEERING CABINET REINFORCING STRAP PLATE | @so00507 | 2

19[DASHBOARD VAC-FORMLHS MOUNTING BRKT | #5000336 [|_1
9_[OPIDOWN SHIFTER MOUNTING BRKTsoon|
@_[DASHBOARD VACFORM MOUNTING BRETasom0s0fa

EVA FLOOR MAT -GREY ee 5 2H0050, FLAT WASHER FLAT WASHER

Page 78

obea

€L

ITEM DESCRIPTION PART No. [QNTY

EI_[RPB-YELLOW WIVIEWPOINT CHANGE LOGOemno007s[1
wis[MS WHIZzTITE NUT-BzP27000151
BIt_[Mox16 SECURITY BUTTON HEAD SCREW - SUSaexo0088[4

1B9__|\MSx20 SECURITY BUTTON HEAD SCREW 26300039

BS[MSx12 SECURITY BUTTON HEAD SCREW - SUS2ex00085 |6
B7_|MBx16 HEX HEAD SET SCREW - BZPss300796|
MS SPRING WASHER TYPE B - BZP280000:q
WASHER 27410835000309[1
186_|\Mox16 SECURITY BUTTON HEAD SCREWaexo0088 |3
‘M6 SPRING WASHER - SUSaxo00012 |3
19[LoctirE 24295000009
“1_|SPEEDO PLEXI- PRINTED“2000005 |1
0[SPEEDO BACKING PLEXTso000089 |1
39_|STEERING WHEEL - 10° RED LEATHER RACINGsssoo0es[1
38_|STEERING WHEEL BOSS5000382[1
37_|"NAMCO LOGO" DECAL200000H
12[WOODRUFF KEY 6x6x317asoo0ai8[1
1[DASHBOARD VAC-FORM5000337 |1
Page 79

obea vl

ITEM DESCRIPTION PART No.

B12.|MSx40 SECURITY BUTTON HEAD SCREW - SUS26300038 |4
MS FLAT WASHER - SUS28000015 |4
MS SPRING WASHER TYPE B - SUS28000014 |4

B9_|M5x20 SECURITY BUTTON HEAD SCREW - SUS. 26300039

BS|M5x12 SECURITY BUTTON HEAD SCREW - SUS26300045 |2
10 | STEERING CABINET TOP CLOSING WOOD37100044 |1
7|STOP MOTION DECAL400000230 |2
5|DASHBOARD COVER VAC-FORM - GREEN45000338 |1
4DASHBOARD COVER VAC-FORM - YELLOW45000339 |1
3|DASHBOARD COVER VAC-FORM - BLUE45000341i
2|DASHBOARD COVER VAC-FORM - RED.45000340 |1

MCPB PUSHBUTTON - RED 60200581 SPRING WASHER ~

FLAT WASHER &

Page 80

obea SL @O@ PEDAL ASSY.

SEAT ASSY

FLAT WASHER

TEM DESCRIPTION PART No. [QNTY B10 | Moxié SECURITY BUTTON HEAD SCREW -suS | 26300008 ny _[MS<i0 SECURITY BUTTON HEADSCREW-Sus | 2600038 MS FLAT WASHER - SUS 2H000015 M5 SPRING WASHER TYPE - SUS 28000014

7| Mi0x20 HEX HEAD SET SCREW SUS“e006

MIO FLAT WASHER HIDUTY -SUS 28000013 MIO SPRING WASHER TYPE BSUS 28000009 6 _ | MOS SECURITY BUTTON HEADSCREW-Sus | 26300036 5 _ [M620 SECURITY BUTTON HEAD SCREW-SuS | 26300901 MGFLAT WASHER HIDUTY - SUS e0067 M6 SPRING WASHER TYPE - SUS 28000012 “46_|[ FUSE WARNING LABEL 5A,

1[LocrTe295000009,
15 _ | STEERING CABINET END COVER BRACKETsoos|
T_|STEERING CABINET FOOT WELL JOINT BRKToe
1_[BASE REAR/TOWER SAFETY RUBBERsooo
12_|STEERING CABINET SAFETY RUBBER BRACKET| aso00u0[1
n_[LHS Foor RESTsoos |_t
10 _ | STEERING CABINET SAFETY RUBBER PACK PLATE|«so0m09[1

[ACCELIBRAKE DUAL PEDAL ASSY WiPOTS ‘eenoooa)

Page 81

obea

9L ITEM DESCRIPTION PART No. | QNTY

B16|M20 SPRING WASHER TYPE B - BZP280000101
B15[M20 FLAT WASHER H/DUTY - BZP280000111
B14[M20 FULL NUT - BZP270000201
B7_|Msx6 DOG HEAD GRUB SCREW263000341
B6|Md4x8 DOG HEAD GRUB SCREW263000351
B4 | M6x40 HEX HEAD SET SCREW - BZP265004341
B3_[M6 NYLOC NUT- BZP270001721
B2_|M6x8 DOG HEAD GRUB SCREW263007614
19|LOCTITE 24295000009
17[UNIVERSAL JOINT SHAFT EXTENSION 155mm.450003601
16[UNIVERSAL JOINT SHAFT EXTENSION 75mm450004511
15[UNIVERSAL JOINT SHAFT EXTENSION COUPLING | 450003611
14| STEERING SHAFT GEAR P130-3GT-15-6W450003551
13[PILLOW BEARING BLP-205450002291
12| WOODRUFF KEY 8x7x3245000363 |2
11|SPACER WASHER 9mm450004521
9UNIVERSAL JOINT NP-18-NOA-02450002711
8|STEERINGSTOPPER BUMPER45000359 |2
7| STEERING STOPPER450003581
6|KEYED SPACER WASHER45000387 |3
5.| STEERING DRIVE SHAFT450003531

FLAT SPACER WASHER 45000362 wocreme 242

Page 82

obea

LL

ITEM DESCRIPTION PART No. [ QNTY

ES[TRANSFORMER 0.220-240/ 15v@05A-24v@3A| 67700031[1
B10[Ma WHIZZTITE NUT. BZP27000128 | 6
B2_[M&x30 HEX HEAD SET SCREW - BZP26500407 |4
‘M8 FLAT WASHER HIDUTY - BZPse300702 |4
‘M8 SPRING WASHER TYPE B - BZPaxoo0027[4
19[LOCTITE 24295000008
4 _ [STEERING MOTOR PCB MOUNTING BRACKET5000352[1
1[STEERING ASSEMBLY TRAY45000350[1

x

@

: SPRING Qo wasuzr o— FLAT WASHER

Page 83

obea FLAT WASHER,

tj @ FLAT wasien 8

BL DESCRIPTION PART No,

Mo FULL NUT-BZP 27000021

M6 FLAT WASHER HIDUTY- BZP.280000372FLAT WASHER

2 HEAD A 7369005 7 SPRING MSxI2 POZI PAN HEAD SCREW - BZ? 26300576 uasues , O_o arwastier

FLAT WASHER HIDUTY - BZP2SH00822«

28000010 26300085 2 Bi) x2

[M3x10 POZI PAN HEAD SCREW - BZP263000674a
[M3 FLAT WASHER - BZP2s0001074
MS SPRING WASHER-BZP280001094
Mx25 HEX HEAD SET SCREW - BZP263000504
MS FLAT WASHER H/DUTY - BZP‘e83007024
MS SPRING WASHER TYPE B-BZP2s4
ES[20mm PANEL MOUNT FUSE HOLDER3500785
ET[20mm FUSE SA SLO-BLO‘3500600

EI_ [STEERING MOTOR PCE XAD-STEER PCB 3 _ [STEERING MOTOR 24v DC 15w SOORPM 45000367

19fLocrire 22‘95000009

16 _ | STEERING DRIVE BELT 597-3215, "45000356 15 _| STEERING MOTOR DRIVE PULLEY P26-3GT-15-6F 45000354

3_[SHORTY BUSHING39000051

2 _ | STEERING MOTOR MOUNTING BRACKET “45000351

Page 84

obea 6L ITEM DESCRIPTION PART No. | QN'

B4_| M6x40 HEX HEAD SET SCREW - BZP265000344
FLAT WASHER H/DUTY - BZP883007914
‘SPRING WASHER TYPE B - BZP280000344
B3_|M4x25 POZI PAN HEADSCREW - BZP263000604
‘M4 FLAT WASHER H/DUTY - BZP280000364
‘M4 SPRING WASHER TYPE B - BZP280000184
B2 _ |M8x30 HEX HEAD SET SCREW - BZP26500407 |IC

M8 FLAT WASHER H/DUTY - BZP 300702 | 1¢

M8 SPRING WASHER TYPE B - BZP28000027 |1
BI|M8x40 CSK SET SCREW - BZP263008554
42[SPEAKER BOX371000241
28[SEAT SUPPORT BRACKET - RHS450004151
25[SEAT ANGLE SUPPORT BRACKET - RHS450004091
24[SEAT ANGLE SUPPORT BRACKET - LHS.450004081
20|SEAT REAR WOOD371000651
19|SEAT BASE WOOD371000641
18SEAT SUPPORT BRACKET - LHS450004141
17|SEAT SUPPORT BRACKET450004041
16|SPEAKER - WOOFER B141620000621
38[LocTITE 242‘95000009
Page 85

obea ITEM DESCRIPTION PART No | QN1

B7_|M8x20 BUTTON HEAD SCREW - BZP26500119 |4

M8 SPRING WASHER - BZP 28000027 | 4

B6[M8x40 BUTTON HEAD SCREW - BZP26500408 |4

M6 FLAT WASHER H/DUTY as300701 | 4

M8 SPRING WASHER - BZP28000027 |4
BS_|M5x25 POZI PAN HEAD SCREW - BZP36300049 | 12

MS FLAT WASHER H/DUTY - BZP. as3007e9 | 12 M5 SPRING WASHER TYPE B - BZP 28000026 | 12

4|M4x25 POZI PAN HEAD SCREW - BZP26300060 | 16

M4 FLAT WASHER H/DUTY - BZP 28000036 | 16 M4 SPRING WASHER TYPE B - BZP 28000018 | 16

81|SEAT REAR SUPPORT BRACKET45000413 |1
42|4%" 20w SPEAKER2000006 |2
40|SEAT ADJUST LEVER4500048 |1
39SEAT RUNNERS (SET)45000449 |1
38HOSE CLIP96000021 |2
37|CONVOLUTED TUBEgg0o00s0 |1
34[CONVOLUTED TUBE TOP VAC-FORM45000303 |1
33|BASS SPEAKER VAC-FORM45000392 |1
31|SPEAKER GRILLE SUPPORT BRACKET45000410 |1
21|HEADREST FRONT SPEAKER GRILLE.45000406 |1
18|SEAT FIXING BRACKET45000405 |1
75|LOCTITE 24295000009
Page 86

obea

TEM DESCRIPTION PARTNo | QNTY

B16[MSx1ax10 RAWLNUTaro001s3|
Be|MS325 SECURITY BUTTON HEAD SCREW - SUSaeonsfa
M5 SPRING WASHER SUSawo0001afa
7a[NAMCO SEAT DECALsoo000662
SEAT DECAL SET- YELLOW00000671

SEAT DECAL SET- GREEN rr

aatsSEAT DECAL SET - RED400000701
SEAT DECAL SET- BLUEo000069[1
[HEAD REST REAR SPEAKER GRILLEas000807|
15_|SEAT REAR SAFETY DECALso000333fa
SEAT REAR VAC FORM - YELLOW5000567|1
SEAT REAR VAC FORM - GREENas000381fa
adSEAT REAR VAC-FORM - RED450003891
SEAT REAR VAC FORMBLUEaso00nsfa
Page 87

obea zB

TEMDESCRIPTIONPART No[QNTY

BS [MS WHIZZ NUT Tamas | 2

BigsRAWENUTmms|B
  • _|6i0 HEX HEAD SET SCREW -ZP MIO FLAT WASHER HIDUTY -ZP a NS SPRING WASHER TYPE BZP 5
‘he[S25 SECURITY BUTTON HEAD SCREW -SUSamma[2
THe|NSGDOSECURITY BUTTON HEAD SCREW SUSESTE
7_| WASHER 156 PLASTICa
36]SEAT UNIT7
31_[WASHER 1sx6- INTEC‘sms[2
2 _ [WASHER IS6-SUS‘smoaie|

SEAT HEADREST VAC FORM VELLOW ‘smose |

SEAT HEADREST VACFORM GREENsme|
"SEAT HEADREST VAGFORM- REDsoe|

SEAT HEADREST VAC FORM BLUE immer |

SEAT LOWERVAC-FORW RAS” YELLOWwm[a

SEAT LOWER VACFORM RAS GREEN ‘simoses | SEAT LOWER VNG-FORM RES RED 7

SEAT LOWERVACFORW RAS” BLUE7
SEAT LOWERVAC-FORM LHS YELLOWa

SEAT LOWER VAC FORM IIS GREEN 7

7|SEATLOWER VACFORW LAS-REDsmn|
SEAT LOWERVACFORN LAS BLUETamme |

rocrne 2a ‘sn

Page 88

obea €8

NOTE: FIT TO THIS SIDE FOR YELLOW & RED FIT TO OTHER SIDE FOR GREEN & BLUE

BI

TEM DESCRIPTION PART No [ ONTY 19 _|MSx16 SECURITY BUTTON HEAD SCREW - SUS aawoosa | 3a 62)

30_|SAFETY RUBBER BACKa

31_|SAFETY RUBBER REAR LISS somes | 2

32_|SAFETY RUBBER - FRONTcs
3o_| SAFETY RUBBER - SIDE LHSIRNS - MIDDLE SECTIONscons | 2@)
Si_| SAFETY RUBBER -SIDELHSIRHS REAR SECTIONasownas | 2
35_|SAFETY RUBBER - SLIDE COVER BRACKET - REARsoma | 2
36_| SAFETY RUBBER - SLIDE COVERBRACKET - FRONTaso | 2
37_|SAFETY RUBBER - SLIDE COVERBRACKET - OUTSIDEscons | 2
38_| SAFETY RUBBER RETAINING BRACKET - BACKsonia|
39 _ | SAFETY RUBBER RETAINING BRACKET - FRONTss00130[1
Go _ | SAFETY RUBBER RETAINING BRACKET - REAR LHSsso|

61 _| SAFETY RUBBER RETAINING BRACKET - REAR RAS es

@_|SAFETY RUBBER RETAINING BRACKET - SUSasowas | 2

G_|SAVETY RUBBER RETAINING BRACKET -SLIDE COVER LHS | aSo00a34 [1

Gi_|SAFETY RUBBER RETAINING BRACKET -SLIDE COVER RHS5000885[1
GS_|SAFETY RUBBER RETAINING BRACKET-SIDELHSe006|
G6 _ [SAFETY RUBBER RETAINING BRACKET -SIDE RNSsso000s7|
Page 89

obea v8

1TEM DESCRIPTION PART No

BI__| Mox16 SECURITY BUTTON HEAD SCREW - SUS26300044

82 _ | Msx16 SECURITY BUTTON HEAD SCREW - SUS 88300795

3_| SLIDE COVER BRACKET SAFETY DECAL - LHS40000226
2.__| SLIDE COVER BRACKET SAFETY DECAL - RHS40000227
1_| SAFETY DECAL STRIP - YELLOW/BLACK40000224

E 95000000 LOCTITE 242

Page 90

obea $8

ITEMDESCRIPTIONPARTNo[QNTY
B23| Msx20 HEX HEAD SET SCREW - BZ?ssa00700[4
Mi FLAT WASHER - BZPwsxoo72|4
[MW SPRING WASHER - BZPasoo0i76 |4
Bia[Ms waizzrine NUTaroooisi_| s

BS _ | Msxi2 PZ CSK SCREW - SUS aes00069 |

Ba[MSx12 SECURITY BUTTON HEAD SCREWSUSaeaoons|34
35 _ [REAR BASE COVER PLATE DECAL - RHSooo007s[a
34_[REAR BASE COVER PLATE DECAL LHSsooo007a|
33_[FRONT BASE COVER PLATE DECAL - LHSIRHS40000073
21 _ [SUSCASTOR ROLLER PLATEaso[2
20__| SHIPPING BRACKET - REARaso00264 |2
19 _ | BASE REAR "NAMCO" DECALsooo|
1s[BASE "FORK HERE" DECALwooo[4
17_[SERIAL NUMBER PLATEwee|ot
16[RIVETS2x05aso00010|4
15 _ | MOTOR EMERGENCY STOP DECALooomas|
10|SDESTEP PLATE5000875
5 _ [REAR BASE COVER PLATE - RHSasoo0s74[1
@__[REAR BASE COVER PLATE - LHSaso00a7s|a
3_[FRONT BASE COVER PLATE - RHSaso00s72[1
2__[FRONT BASE COVER PLATE LHSsoot|
as_[Locrire 22000009[=
NOTE: FIT TO THIS SIDE FOR YELLOW & RED FIT TO OTHER SIDE FOR GREEN & BLUE
Page 91

obea

ITEM DESCRIPTION PART No

BI |M8x20 HEX HEAD SET SCREW - BZP 88300700

B2 _ |M10x30 HEX HEAD SET SCREW - SUS 88300703

MIOFLAT WASHER - SUS 28000013

MIO SPRING WASHER TYPE B - SUS 28000009

2 | REAR SHIPPING BRACKET 45000264

FRONT SHIPPING BRACKET 45000369

Page 92

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 93

obea

TEM DESCRIPTION PART NO

17[WASHER BZ?sooner|
Bs[Mlox30 HEX HEAD SET SCREW -1ZP2esonaae |4
M10 SPRING WASHER TYPE B-BZP2aooooas[4

B6_[MSRAWLNUT aromiss | ®

HS _ [Msx20 SECURITY BUTTON HEAD SCREWS -SUSzea |26
BI[Moxa0 HEX HEAD SET SCREW -RZP2esooass|e

FLAT WASHER x1" -BZP 2soooo | & SPRING WASHER TYPE B- BZP cr

12[HANTAREX 35° POLO MONITOR WiREMOTE,2
10 _ [DECAL MONITORVACFORMwom[4
[MONITOR TOP VAC-FORM- YELLOWsso|1
[MONITOR TOP VAC-FORM- GREENsomos? |a
(MONITOR TOP VAC-FORM- BLUEssomais[1
[MONITOR TOP VAC-FORM- REDsoma[1
1 _ [Fume SURROUND VAC-FORMsomos |2
38|LocriTe 24295000009,
Page 94

obea

TEM DESCRIPTION PARTNo | ONTY

iba _ [M420 POZI PAN HEAD SCREW - BZPaexmooss[4
'Ma SPRING WASHERaaonoois| 4
BS _ | Max25 POZI PAN HEAD SCREW - BZPaes[4
Ma FLAT WASHER - BZPaaonoose |4
32[4x20 POZI PAN HEAD SCREWBZP2es00oss[1
Ma SPRING WASHER - BZ?aaon00as[1
wBi_|Nox" POZI FLANGE HEAD SCREW - BZPpeor[4
12 _ [AMPLIFIER ASSEMBLYsoos|a
1_|[SMPSU MOUNTING BRACKETweno|
10 _ [Psu woopsnioo0e2[1
9 _ [FUSE COVER STRIPaepo
[FUSE NW 1A SLO-BLOeases| 4
7_[FUSE TW 2A SLO-BLO@3s00506 |5
© _ [FUSE TW 3A SLO-BLOeasuosaT|1
3_[FUSE STRIP Swaye000[1
4_[BLKAY Sway TERM BLOCKecono[2
3_[PCB MOUNTING PILLARsoon0080|
LAMP DRIVER PCBso00002[1
7|SMPSUSv30A 725Asso00004[1
Page 95

7 TOWER ASSEMBLY

rower surrey wnsee Agsr

a 3 ~

taoaT masiToR assy @Hy
wowtoR assy a> |=as oa f7
:a{1}

sie FR] Tete

teUWKs
" ampiriee Assy=4'=
igone=
i=osa:
ienodace!:snr I)oy PRBi
feeds [ld:hehea gsi1 wa@eceasy 5 TT

1 ace PCR ASSY _ : : |

Page 96

We ive “sreeeng 6 SAL BRN, SEAT ASSEMBLY

1¥SWITCH ASSY
:cp eg:

caeen te — te

3H i alsG1.
[arr goeraaeSHIFT ASSY:

Few a | ma nis

::acceuenaToR
7 ef sores=:
ieee Sainso} AB PEDAL ASSY:

a Ce oniene z

én :

Pent)etget
PEARER ty 3 {PURPLEf=etanFL Sites:
:Zass
—= :atYjan
soez:
Hie $ae:
2'::
1meen-4

o ge EL hee ;

12 seein st aSea sree :STEERING ASSY
| 2 RAEa b !:
SECURITY 2 eRSECURITY cB1

ao Game OVER 1 eee [GAME _DVER aasy

oecam:
:"ar aE, Rc p:
mez—eeea:
(20v ALR3 (oad:

: ——— rw re,

::a
::voroe

SWITCH en

.Sa SLO-BLO DRUM DRIVE PCB ASSYao
:=;ony°
Ty ACRTA =e -2ooU6y” AC RIN oeROL Bl +{
: aT secuaEswerosie woLee|
sv" $raedeycarey I| :
see Seareaero |vee i:
oy SL ERA oTee:

z mswmm] EDA) Beater

:‘PINK ‘wase wOTeR, a'
Page 97

POWER SUPPLY BOARD

SWITCH MODE POWER SUPPLY

Page 98

—PNKZBRN

| METER | | <S10 ONLY | Lo. J

i | COIN DUT <R> COIN GND COIN OUT <L> COIN GND METER

GRN/YEL

DIN LAMP +i2v

MARS CASHFLOW 340 PCB