CATHODE RAY TOMES

Alpine Racer 46in

Alpine Racer (World, AR2 Ver.D) (Namco, 1994) · Document · 51 pages · 12 sections · original scan

Page 1

Operators Manual

IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY AT

ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY,

Part No. 90500040

Page 2

© 1994 na m co all rights reserved.

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for public or private use, without permission from NAMCO EUROPE LTD.

While the information contained in this manual is given in good faith and was accurate at the time of publication, NAMCO EUROPE LTD. reserve the right to make changes and alterations without notice.

This machine has been manufactured in accordance with European Community directives (1st. January 1996), and as such bears the C € marking. Any changes or modifications to this machine must be in accordance with European Community directives (1st. January 1996).

If you make any unauthorised changes to this product, you may contravene European Community directives (1st. January 1996)

Published by: NAMCO EUROPE LTD. Namco House, 8 Acton Park Estate, The Vale, London. W3 7QE

Phone:- 0181-324-6000 Fax:- 0181-324-6010

Page 3

SAFETY WARNING

In order to use this machine safely, be sure to read this Operators Manual carefully before installation, adjustment or use of this machine. Whenever the owner of this machine entrusts disassembly, installation, adjustment, routine maintenance or trouble shooting to another person, the owner should ensure that that person read the appropriate precautions and relevant sections of this manual before starting work. In order that no accidents occur when the machine is in operation, strictly follow the notes on safety described below. Also, carefully read section 2, "Precautions"

Warnings for Operation (€ € Requirements) r »

NOTE: Only operate this machine after checking that it has been installed correctly and in accordance with the installation and commisioning manual.
NOTE: Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There are warning notices to keep hands and feet clear of moving parts, however if the operator feels that a person is in any danger, he should warn that person accordingly.
NOTE: The warning notices must always be kept in good condition and replaced if worn, so that the customer can read it clearly.
NOTE: If there is an error or problem with this machine, operation must be stopped immediately and the problem rectified before further use. Ne /

Warnings for Disassembly, Installation, Routine Maintenance, and Troubleshooting.

Va

DANGER: _ Namco Ltd. bears absolutely no responsibility for accidents or injuries resulting from unauthorized changes to this machine.
DANGER: _ Ensure that the machine has been turned OFF before making adjustments or carrying out maintenance. Also ensure only qualified personnel carry out maintenance or turn the power ON to this machine.
DANGER: _ The power supply and inside the monitor will remain hot and have areas of high voltage even though the machine has been turned OFF, and there is a possibility of burns or electric shock. Be careful not to touch these areas.
DANGER: _ Inorder to avoid injuries due to mis-operation, be sure that the voltage of the main power supply is within the prescribed limits. Also to prevent possible electric shocks due to failure, this machine MUST be fitted with a securely connected earthed plug.
NOTE: Do not turn the power switch ON until the machine has been installed correctly. )
Page 4
  • SPECIFICATIONS

POWER SUPPLY :-

MONITOR :-

COIN ACCEPTOR

DIMENSIONS :-

Assembled Monitor Cabinet Ski Assembly Header

WEIGHT :-

Assembled Monitor Cabinet Ski Assembly Header

ACCESSORIES :- 220/240volts AC

Philips 46" Projector Monitor (46PP912A/05)

Mars CashFlow - 1 Channel

1265(w) x 2245(d) x 2300(h) 1145(w) x 645(d) x 1920(h) 1265(w) x 1600(d) x 1220(h) 1145(w) x 350(d) x 380(h)

433kg 175kg 240kg 18kg

Keys: (Cash Door) yn (Coin Door) (Service Door) ie)

IEC Mains Lead... Operators Manual Installation Manual Monitor Manual... Monitor Remote Control W/Batteries Cashflow Data . Floor Safety Mat & Decal Floor Safety Mat Securing Plate Floor Safety Mat Support Bracket Joint Bracket Potentiomete HAprynesnehol

M10x25 Hex Head Set Screw - S/Steel . M10 Flat Washer - S/Steel..... M10 Spring Washer - S/Steel. M8x20 Hex Head Set Screw - S/Steel M8 Flat Washer - S/Steel ... M8 Spring Washer - S/Steel M6 Dome Head Nut - Chrome M6X25 Hex Head Screw - BZP . M6 Flat Washer H/Duty - BZP M6 Spring Washer - BZP .... NNNODARAROOOW

M4 Security Wrench .. M5 Security Wrench... M6 Security Wrench ..........cceccceeeseseeteeeeees 1

Page 5
  • PRECAUTIONS

Be sure to read this section carefully.

2-1 Notes on Operation (C € Requirements)

(~“ NoTE:

NOTE:
NOTE:
NOTE:
NOTE:
NOTE:
NOTE: >) Only operate this machine after checking that it has been installed correctly and in accordance with the Installation and Commisioning Manual. Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There is a warning sticker that the player must be wearing flat shoes, unsuitable footwear e.g. high heel shoes could cause the player to lose balance and fall. However if the operator feels that a customer playing the game is in any danger, he should warn the customer accordingly. The warning sticker must always be kept in good condition so that the customer can read it clearly, and be replaced if worn. Ensure customer safety at all times. Be especially careful in the case of young children, who should be supervised by an adult at all times. If there is an error or problem with this machine, operation must be stopped immediately. Service, adustments and routine maintenance should be carried out by qualified personel only. J

Parts of this machine swing to the left and right during game play. In order to maintain the customer's safety, the operator should strictly follow the appropriate precautions.

2-2 Safety Mechanisms and Controls

For safety, this machine is equipped with a locking mechanism for securing the steps when the machine is not being played.

The step locking mechanism is controlled as describe below.

After selecting the course, the step lock is released before game start.

At game over, the steps are locked.

If the steps are moved left or right while they are locking or unlocking, the motor temporarily stops in order to prevent damage to the step-lock motor. When the steps are no longer being moved left or right, the motor will restart. To prevent damage from occurring, do not move the steps while the motor is running.

When the machine is first turned ON, the step-lock mechanism is checked automatically by unlocking and re-locking the steps.

If the step-locking system fails, an error message will be displayed on the monitor screen. Refer to section 6-4-3 "Handling Motor Errors" and section 8 "Trouble Shooting".

Page 6

Restriction plate

(a) = ale

hd ¥o ze Step

Unlocked step (free state)

The restriction plate moves to the side of the steps and locks the steps.

Step

o&) ° Foo Ed

Locked step La

2-3 Cautions When Transporting.

a. Do not subject the game to physical shock when transporting or moving it.

b. Always return the levellers to the UP position before moving the machine, even for short distances.

c. The monitor cabinet, ski assy and header assy must be separated before shipping.

d. Take care not to rope any moulded (plastic) parts when transporting.

e. Always ship the monitor section upright.

THIS MACHINE IS NOT DESIGNED TO BE MOVED BY FORK LIFT. DO NOT USE

Page 7

2-4 Cautions When Installing.

This machine is designed for indoor use only. Do Not install the machine in the following places 1.

[® Direct sunlight, places with excessive humidity or dust, places where there is water leakage, near airconditioning or heating equipment, places with excessively high or cold temperature.

[ @ Places where it would be in the way of emergency exits or fire extinguishing equipment.

® Places that are not level.

If this machine is installed next to walls or other machines, ensure that there is 2. plenty of space between them.

Page 8

: So that customers are not injured by the movement of the Ski Tray, ensure that there is at least 300mm separation between other machines or walls. If two Alpine Racer machines are next to each other the space between them must be at least 600mm.

: In order to gain access to the Power Supply and CPU assemblies, make sure that the rear of the machine is separated from a wall or other machine by at least 500mm.

30cm 30cm

50cm

(Z SAFETY ZONE 50cm

/ KEEP CLEAR 4) ‘mtr L / ££ f

Page 9
  • HOW TO PLAY

This game is based on Alpine ski racing. The player stands on the steps and moves them left or right to control the skier. By using the inner edge when moving the steps, the skier slows down and turns quickly.

. Race Mode The player races the computer skiers and the object is to cross the goal line first. The game is over when the player crosses the finish line within the given time period, or the time period reaches zero. The time period is increased each time a player passes a check point. f a player wins in a fast time they can enter their initials. Select letters using the select buttons and enter them by using the decision (Viewpoint) button.

. Time-Trial Mode The object of the game is to pass between the flags (gates) and to cross the inish line in the fastest time. The rules require the player to go through the gates, so more technique is needed for this mode than the normal race mode. The game is over when the player crosses the finish line within the given time period, or the time period reaches zero. The time period is increased by one second each time a player passes through a gate. if a player completes a course in a fast time they can enter their initials. Select letters using the select buttons and enter them by using the decision (Viewpoint) button. A player is not disqualified for not passing through a gate, however the player will not be able to enter their initials even if they cross the finish line in a good time.

: Game Mode Selection After inserting sufficient credit, the "Game Mode Selection" screen is displayed. The player selects either the "Race Mode" or "Time-Trial Mode" by using the L/R selection buttons, and pressing the decision (Viewpoint) button.

. Course Selection After the game mode has been selected, the "Course Selection" screen is displayed. The player can select one of three courses, "Novice", "Intermediate" and "Expert".

. Viewpoint Selection The viewpoint button can pressed at any time during a game to switch between the player's view and behind view.

Players View: This is the view as seen by the skier. This provides an exciting view while skiing. The race mode starts in this view.

Behind View: This is the view from behind the skier. This view can be used to get an understanding of the skiers posture and surrounding conditions. The time trial mode starts in this position.

Page 10
  • MAJOR COMPONENTS
Page 11
  • INSTALLATION
WARNING. If the location site of this machine has a polished floor it is recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor.

5-1 Fitting the Header Assembly

The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.

The fitting position of the Header Assembly is very high, and it is important that a means of reaching the height safely, without stretching, is available. (e.g. steps, step stools etc.)

  • Place the Header Assembly on to the monitor cabinet, connect the connectors and pass the connectors in to the cabinet, slide the header back ensuring that it engages fully in to the retaining brackets at the front of the monitor cabinet.
  • Fit the 2off M6x25 Hex Head Screws, Spring and Flat washers to retain the Header Assembly to the cabinet.

Hex Head Screw (M6x25)

Connectors

Page 12

5-2 Connecting the Ski Assy to the Monitor Cabinet.

  • Connect the connectors between the Ski Assembly and Monitor Cabinet.
  • Push the Ski Assembly fully up to the monitor cabinet, taking care not to trap any wires.
  • Fit, finger tight, a joint bracket to each side using 4off Hex Head Set Screws (M10x25), Spring and Flat Washers on each bracket. Tighten fully all screws.

Hex Head Set Screw (M10x25) Joint Bracket \.

Joint Bracket

Hex Head Set Screw (M10x25)

Connectors

Page 13
NOTE:- When the machine is adjusters, (4 on the m all castors are raised ully assembled and in its final position, lower the 10 level onitor cabinet and 6 on the ski assy), with a spanner so that rom the floor, and the machine is level. Tighten the lock nuts with a spanner to ensure that the level adjusters do not move.

Level adjuster

If this machine is installed on a smooth or shiny floor, it is recommended that rubber slip mats be placed under each adjustable foot to prevent the machine from moving when being played.

5-3 Fitting the Safety Mat

  • Assemble the Floor Safety Mat by fitting the securing plates from underneath, the support brackets from the top and retaining the assembly together with the M6 Dome Nuts.

M6 Dome Nut

Floor Safety Base i |

Securing Plate YY

  • Place the assembled Safety Mat into position under the Ski Step Assy.
  • Retain the Safety Mat in position with the Hex Head Set Screws (M8x20), Spring Washers and Flat Washers

Hex Head Sel Serew (M320)

Page 14
  • ADJUSTMENTS

6-1 Turning on the Power

After the machine has been installed, turn ON the power. The power switch is located on the rear of the monitor cabinet.

6-2 Adjustment Switches

The Adjustment switches are located inside the coin door.

1. Service Switch. Press this switch to obtain game credits without incrementing the play meter.

Test Switch Slide the test switch ON to enter test mode. Test mode allows testing and the changing of game settings. (Refer to section 6-3 "Test Mode" (page 12))

COIN COUNTER °

°

LEFT PLAYER RIGHT PLAYER

TEST SERVICE TEST SERVICE

Service Bracket

Page 15

6-3 Test Mode

  • | Open the coin door and slide the test switch "ON". The menu screen will be displayed on the monitor.
  • Select the test required by pressing the 'Left or Right Selection’ push button. The selected test will ‘blink’.
  • Enter the selected test by pressing the 'Decision' push button. Select "EXIT" to return the "Menu Screen".
  • After testing is completed, ensure that the test switch is returned to the "OFF" position to return to normal game mode.

The Test Switch must always be in the "OFF" position for normal game mode.

~ MENU

COIN OPTIONS (1) Sets the price of play (See 6-3-1)

GAME OPTIONS ~— =====---=---}--== (2) Sets the game options (See 6-3-2)

VO TEST(3)Used for testing switches and controls

(See 6-3-3)

SOUND TEST(4)Used for testing sound and setting

volumes (See 6-3-4)

MONITOR TEST — ==-========+ ---- (5) Used for adjusting the monitor

ADS TEST = wwenneneeo==} ---- (6) Displays accumulated game data

OTHERS(7)Used for testing the PC Boards and for

initializing all of the settings

L/R SELECTION BUTTON : CHOOSE DECISION BUTTON : ENTER

Decision Button

Select L/R Buttons

Page 16

6-3-1 Coin Options

Select item (1) "COIN OPTIONS" on the menu screen to set the game cost and related settings.

Press 'Select L/R' to select the required item.

Use the 'Decision' button to adjust the settings.

Select "EXIT" to return to the menu screen. COIN OPTIONS [ DEFAULT IN GREEN ]

GAME COST 1 COIN 1 CREDIT

FREE PLAY OFF

EXIT

SELECT L/R BUTTON : CHOOSE DECISION BUTTON : CHANGE + Ne y

Note :- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the Coin Options on the screen are set as shown in the following table.

ITEM CONTENTS FACTORY SET

  • Game Cost | No of Coins required for No. of credits - - - - - - settable 1-9 | 1 Coin 1 Credit
  • Free Play | Yes/No NO
Page 17

6-3-2. Game Options

  • Select item (2) "GAME OPTIONS" on the menu screen to set the game options and related settings.
  • Press ‘Select L/R' to select the required item.
  • Press the 'Decision' button to adjust the settings. Standard settings are displayed in green.
  • Select "EXIT" and press 'Decision' to return to the menu screen.

Ne AUTO HIGH SCORE INITIALIZE OF!

EXIT 4 GAME OPTIONS [ DEFAULT IN GREEN ]

GAME DIFFICULTY B SOUND IN ATTRACT ON HI SCORE INITIALIZE NO

SELECT L/R BUTTON : CHOOSE

DECISION BUTTON : CHANGE +

ITEM DESCRIPTION FACTORY SET

(a) Game DifficultyA (easy) to C (hard)B
(b) Sound in AttractOn / OffOn
(c) Hi Score InitializeYes / NoNo
  • Auto High Score Initialize | On / Off Off
Page 18

6-3-3 I/O Test

  • Select item (3) "I/O Test" on the menu screen to test the switches, motor and step adjust.
  • Press 'Select L/R't to select the required item, then press the 'Decision' button to enter the test.
  • Select "EXIT" and press the 'Decision' button to return to the menu screen.

( VO TEST )

DIP 4 12345678 oven wau(A)

SWITCH TEST MOTOR TEST STEP ADJUST EXIT

SELECT L/R BUTTON : CHOOSE DECISION BUTTON : ENTER Ne 7

  • Shows condition of DIP SW 4 on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)
  • For testing Switches and Control Pots. (See 6-3-3-1 )
  • For testing the Step-Lock Motor. (See 6-3-3-2)
  • For initializing the Step Control Pots. (See 6-3-3-3)
Page 19

6-3-3-1

Note:
Note: Switch Test

Select Switch Test from the 'l/O Test' menu. The following screen will appear on the monitor.

  • On entering Switch Test the Skis will be unlocked. Ensure that the Skis are returned to the locked condition at the end of the test by entering Motor Test (See 6-3-3-2)

( SWITCH TEST »

TEST SW ON ——hesesestetedeeeee COIN SW ON SERVICE SW ON ws R SELECTION BUTTON’ ON. DECISION BUTTON ON. L SELECTION BUTTON’ ON. SWING 0000 0000 CENTER. EDGE 0000 0000 CENTER. SESeees#ss

UR SELECT + DECISION : EXIT Ne /

The word 'ON' will appear next to items (a) to (f) each time the respective switch is operated. When the skis are pushed left, 'SWING-CENTRE' will change to 'LEFT' and 'OK' will appear just before it reaches the extreme left,. When the skis are pushed right, 'CENTRE' will change to 'RIGHT' and 'OK' will appear just before it reaches the extreme right. '0000' will increase when the skis are moved to the right and decrease when they are moved to the left. When the skis are tilted, 'EDGE-CENTRE' will change to 'LEFT or RIGHT' and 'OK' will appear just before they are fully tilted. '0000' will change as the skis are tilted.

Lett step Right step "EDGE" 'OK' will only appear if you stand and apply weight to the edges of the ski steps. There is no problem if 'OK' is not displayed when standing on the steps in the same way a as normal play.

If 'OK' is not displayed when the edge is tilted left or right, re-initialize as described in section 6-4 "Initialization After Replacing Parts".

Operate both of the 'Select L/R' buttons and 'Decision' button together to exit and return to the 'I/O Test' menu screen.

Page 20

6-3-3-2 Motor Test

  • Select Motor Test from the ‘I/O Test' menu. The following screen will appear on the monitor.

4 MOTOR TEST »)

NOW MOTOR STATE :LOCK......J..... (a)

GO MOTOR : FREE ode (b)

EXIT

L/R SELECT BUTTON : CHOOSE DECISION BUTTON: EXIT

\ /

  • Displays the current condition of the Skis. Display will show 'LOCK - FREEING - FREE - LOCKING' as the Skis are tested.
  • Allows the Skis to be locked and unlocked. Display will show 'FREE - NOW MOVING - LOCK' as the Skis are being tested.
Note:- Ensure Skis are in the locked condition before returning to normal game mode.

6-3-3-3 Step Adjust

  • Select Step Adjust from the 'I/O Test' menu.

On entering 'STEP ADJUST' test, Step Adjust on the 'l/O' Menu Screen will blink and "INITIALIZE COMPLETED' will appear and be blinking.

Ski Step initialization is now completed.

  • Select EXIT to return to the Main Menu Screen.
Page 21

6-3-4 Sound Test

  • Select item (4) "Sound Test" on the menu screen to test the sound and speakers.
  • The following screen will appear on the monitor.

(— >) SOUND TEST

VOLUME LEFT SP. TE wneeeafeneennesnsee (a)

RIGHT SP. TE weeeeafeneennenosee (b)

REQUEST SONG No. i (c)

EXIT

L/R SELECT BUTTON : CHOOSE DECISION BUTTON : ENTER Ne S/

  • Select the required item by 'Select L/R' buttons. The selected item will ‘blink’.
  • Pressing the Decision button will cause the selected value setting to blink.
  • Pressing ‘Select R' will increase the value and ‘Select L' will decrease the value.
  • Press ‘Decision’ button to return to item select mode.
  • When selecting the ‘Request Song No.' test, 'Select R' button will increase the song number and ‘Select L' will decrease the number. The 'Decision' button will produce the sound of the song number selected. (Request Song 01 will produce a stereo sound test. Sound will be produced from the speakers in the following order:- Left speaker, Right speaker, Both speakers)
  • Press both Select L/R buttons and Decision button together to return to Sound Test Menu from Request Song No. Test

Item Description Factory Set

aSetleftspeakervolume= =——_—-- -----00 Quietest - 3F Loudest3A
bSet right speaker volume=- ---- -00 Quietest - 3F Loudest3A
cSelect sound for testing. Each number will produce a different sound. 01 willa

generate a stereo test.

Page 22

6-3-5 Monitor Test

  • Select item (5) “Monitor Test” on the menu screen to set up and adjust the monitor.
  • Onentering monitor test, the screen will display one of the following test patterns.
  • Use 'Sel to return

6-3-6 ADS Data GRADATION PATTERN CROSSHATCH GREEN CROSSHATCH WHITE WHITE WINDOW (H) WHITE WINDOW (M) WHITE WINDOW (L) INTERLACE PATTERN VIEW ANGLE ADJUST (CRT) VIEW ANGLE ADJUST (PROJECTOR) FULL WHITE

lect L/R' buttons to change to the next pattern and 'Decision' button to the Main Menu.

  • Select item (6) "ADS Data" on the menu screen to view machine history details.
  • The following screen will appear on the monitor.

(— ADS >

RACE TI.

NOVINTEXPNOV INTEXP
PLAY0000 0000 00000000 0000 0000
GOAL0000 0000 00000000 0000 0000

EXTO 0000 0000 0000 EXT1 0000 0000 0000 EXxT2 0000 0000 0000 GATE ---- ---- eee

NOV INT EXP

RACE000'00"00000'00"00000'00"00J... (g)
T.T.000'00"00000'00"00000'00"00J... (h)

PLAYTIME 000" 00" 00 PLAYNUMBER 0000 INITIALIZE (k) EXIT

LIRSELECT : CHOOSE

DECISION : ENTER

X y,

Page 23

Item Description

  • Play Total number of games played at each difficulty level for each course.
  • Goal Total number of games completed at each difficulty level for each course.
  • Exto Number of games finishing at 1st extended time gate at each difficulty level in race game.
  • Ext1 Number of games finishing at 2nd extended time gate at each difficulty level in race game.
  • Ext2 Number of games finishing at 3rd extended time gate at each difficulty level in race game.
  • Gate Total number of gates completed for each difficulty level in T.T. game.
  • Race Total time in Hrs, Mins, Secs each difficulty level has been played in race game.
  • T.T. Total time in Hrs, Mins, Secs each difficulty level has been played in T.T. game.
  • Play Time Total time in Hrs, Mins, Secs game has been played.
  • Play Number Total number of game plays.
  • Initialize Resets all ADS Data to zero.

6-3-7 Others

  • Select item (7) "Others" on the menu screen.
  • Onentering 'Others' the following screen will appear on the monitor.
  • Selecting Back Up Memory Initialize will return all adjustable settings to OTHERS (DEFAULT IN GREEN)

BACK UP MEMORY INITIALIZE NO

EXIT

L/R SELECTION BUTTON : CHOOSE

DECISION : CHANGE +

factory preset.

Page 24

6-4 Initialization After Replacing Parts

Initialization must be performed after replacing the game PC board, Rom or Step Controls. If initialization is not performed, the game will not function correctly. During initialization, ensure that the step edges are level.

6-4-1 Adjustment Method (a)

  • When the power is turned ON the step-lock motor is automatically checked. The motor check first locks the steps, frees them, then locks them again.
Note: Ensure that the test switch is OFF during motor check. Also ensure that the steps are not touched during the motor check, or the check will not be performed correctly.
  • If the first lock is not completed within fifteen seconds from power up, an error display screen appears. If this happens, refer to section 6-4-2 "Adjustment Method (b)", and initialize the controls. If the error display screen is still MOTOR ERROR 1 showing after the controls have been PLEASE STEP ADJUST initialized, refer to section 6-4-3, "Handling Motor Errors". After the motor check is successful the attract screen is displayed.
  • To initialize the controls, Switch the test switch ON while pressing the service button. The screen displays the "SWITCH TEST" screen with INITIALIZE COMPETED flashing, Initialization is completed.
  • Turn the test switch OFF to return to normal game mode.

4 SWITCH TEST )

TEST SW ON COIN SW ON SERVICE SW ON R SELECTION BUTTON On DECISION BUTTON ON L SELECTION BUTTON ON SWING 0000 0000 CENTER EDGE 0000 0000 CENTER

INITIALIZE COMPLETED \UR SELECT + DECISION : EXIT )

Page 25

6-4-2

6-4-3 Adjustment Method (b)

Slide the test switch ON.

Turn the power OFF and then back ON again.

Select "I/'O TEST" and press the decision button (View Change).

Select "STEP ADJUST" and press the decision button. The controls are now initialized.

Atter initialization is completed, turn the test switch OFF. The motor check begins. If the motor still does not operate correctly, there is a problem with the motor or switches, and an error will be displayed on the screen. Refer to section 6-4-3, below, "Handling Motor Errors", for fault finding.

Handling Motor Errors

If a problem has occurred with the step-lock motor, an error message and method of rectifying will be displayed on the screen.

Errors at Start-up

When the power is turned ON the step-lock motor is automatically checked. The motor check first locks the steps, frees them, then locks them again.

Note: Ensure that the test switch is OFF during motor check. Also ensure that the steps are not touched during the motor check, or the check will not be performed correctly.

If the first lock is not completed within fifteen seconds from power up, the following error display screen appears. If this happens, refer to section 6-4-1 "Adjustment Method (a)", and initialize the controls.

MOTOR ERROR 1 PLEASE STEP ADJUST

If an error other than the one shown above is displayed, it is possible that a fuse has blown, there is a problem with the step-motor mechanism or the steps are not moving freely.

Page 26

d. If the first lock is completed within fifteen seconds, but the steps cannot be released, Motor Error 2 screen is MOTOR ERROR 2 displayed until the fault is rectified. OPERATION STOP!!

e. If after the steps have been freed, they do not re-lock, as an emergency measure, Motor Error 3 screen is displayed. This allows the step-lock mechanism to be overridden and the game to be MOTOR ERROR 3 operated with the steps DO YOU WANT TO OPERATE permanently in the free position. YES>PUSH DECISION BUTTON

WARNING: It can be dangerous to NO>PUSH L/R SELECT BUTTON operate the machine with the steps permanently free, so the fault MUST be repaired as soon as possible.

If the game is to be operated with the steps in the free condition, press the decision button. If either the Left or Right Select button is pressed the game will cease to function until the fault has been rectified.

  • An Error Occurs During Play.

a. If the motor stops function during game play, the following error screen will be displayed.

b. Turn the power OFF and then back ON. The motor will be checked automatically.

c. If there is still a problem, follow the instructions detailed in section 6-4-3 (1), “Errors At Start-up".

WARNING! STEP LOCK DEVICE IS OUT OF ORDER CALL THE ATTENDANT IMMEDIATELY.
Page 27
  • MAINTENANCE
DANGER: In order to prevent injury or electric shock to service personnel, ensure that the MAIN POWER IS OFF before attempting any maintenance.
DANGER: Before performing any work not described in this manual, be sure to contact your distributor to receive instructions or answers to questions.

7-1 Care of the Projector Monitor

The projection tube lenses have been manufactured from plastic material. Prevent contact with the lenses, because various lens faces have been provided with a special coating which is easily damaged.

Only the side of the lens directed towards the mirror, the mirror and the projection screen are allowed to be cleaned.

If cleaning is absolutely necessary, observe the following points :

  • Blow off dust, or remove with a dust brush or soft lint-free cloth.

. If necessary, clean with a soft lint-free cloth, moistened with water to which a little detergent has been added.

. DO NOT USE organic solvents such as alcohol, dry cleaning naptha, trichlorethylene, acetone, etc., these agents may cause permanent damage to the plastic lenses or projection screen.

TUBE LENSES

Page 28

7-2 Replacing the Fluorescent Tube

  • Remove the ten socket button head screws (M5x12), and remove the side vacforms (five screws on each vac-form)
  • Remove the two socket button head screws (M4x25), and remove the header acrylic retaining bracket.
  • Remove the header acrylic by lifting it from the lower retaining pins.
  • Replace the fluorescent tube.
  • Reassemble in reverse order.

Socket Button Head Screw (M4x25)

Header Acrylic Retaining Bracket

Fluorescent 3°

Page 29

7-3 Replacing Push Button Switches and Lamps

  • Remove six security screws (M5x20) and two security screws (M5x12), and lift off the top cover taking care not to strain the wiring.
  • Disconnect the connector.

Security Screw (M5x12) -~ Le Security Screw (M5x20) \

Top Cover Security Screw (M5x20)

Connector

  • Separate the switch/lamp holder from the button by pulling it directly away from the button.

Pushbutton

  • Replace the lamp or switch ensuring that the correct wires are replaced on the terminals.
  • Reassemble in reverse order.
Page 30

7-4 Replacing the Step Limit Switches

WARNING: — Ensure that the machine is disconnected from the main power supply before commencing work.
  • Remove the top cover. (See Section 7-3)
  • Remove four security screws (M5x12) securing each side vac-form to the mast assembly and remove both side vac-forms and front vac-form as one assembly.

Side Vac-Form Right

Security Screw (M5x12)

Side Vac-Form Left

Front Vac-Form

  • Remove two pozi head screws (M4x10) and remove the limit switch mounting bracket.

Pozi Head Screw (M4x10)

Switch Mounting Brkt

Pals UG C

Page 31
  • Remove two pozi head screws (M3x16) and replace the limit switch ensuring the wires are replaced on the correct terminals.

Switch Mounting Bracket

Micro Switches

Pozi Head Screw (M3X16)

  • Reassemble in reverse order.

7-5 Replacing the L/R Turn Control Pot

WARNING: — Ensure that the machine is disconnected from the main power supply before commencing work.
  • Remove eight security screws (M5x20) and remove the front Vac-form.
  • Remove two pozi head screws (M4x10) and remove the control pot cover.

Side Vac-Form (L)

Security Screw (M5x20)

Front Vac-Form

Ski Step Assy

Page 32

5)

6) UR Pot Cover

Disconnect the connector, slacken the pot retaining grub screw (M4x8) and remove the control pot and bracket.

Replace the control pot taking care to ensure that the wires are replaced to the correct terminals.

Grub Screw (M4x8)

Connector

Reassemble in reverse order.

Re-initialize game. (See 7-7 "Adjustments When Replacing Parts")

NOTE: When refitting the control pot ensure that the pot locating tab engages in the hole in the mounting bracket and that the grub screw (M4x8) engages on the flat of the pot shaft.

a g Grub Screw (M4x8) Pot Shaft

Mounting Bracket Lj

Page 33

7-6 Replacing the Tilt Control Pot

  • Remove the front vac-form. (See Section 7-3)
  • Remove four security head screws (M5x12) and remove the Ski Step front vacform.

Security Screw (M6x12)

\ Security Screw (M5x12)

  • Disconnect the connector, slacken the pot retaining grub screw (M4x8) and remove the control pot and bracket.

Ski Step

  • Replace the control pot taking care to ensure that the wires are replaced to the correct terminals.
  • Reassemble in reverse order.
  • Re-initialize game. (See 7-7 "Adjustments When Replacing Parts")
NOTE: When refitting the control pot ensure that the pot locating tab engages in the hole in the mounting bracket and that the grub screw (M4x8) engages on the flat of the pot shaft.

Tilt Control Pot Grub Screw (M4x8) Mounting Bracket

| Pot Shaft

Page 34

7-7 Removing the Step Rubber

  • Remove three security screws (M5x12) and retaining bracket from the outside edge of the step rubber, Lift the rubber edge and remove the three inner security screws (M5x12) and retaining bracket.

Security Screw (M5x12)

Ski Step Assy

Rear Vac-Form

Retaining Brkt

  • Tilt the step assembly and remove three security screws (M5x12).

Security Screw (M5x12)

ay

Retaining Brkts

Security Screw (M5x12)

  • Remove the step rubber.
  • Refit in reverse order.
Page 35

7-8 Step-Lock Maintenance

7-8-1 Releasing the Step-Lock

  • Turn the power switch ON
  • Press the service switch, and start the game.
  • When the game starts, the restriction plate (see diag.) moves to the released position.
  • When the steps are released, turn the power OFF.
  • To re-lock the steps turn the power ON and the steps will re-lock in the power up motor check.

7-8-2 Greasing the Step-Lock

WARNING Make sure that the power is turned OFF. If work is to be carried out with the covers removed, take care not to trap hands or fingers in the mechanism.

The step-lock should be greased every three to four months.

  • Remove the control panel and vac-forms (See sections 7-3 and 7-4).
  • Apply grease to the following locations.

¢ Between the restriction plate and guide rails, and between the cam follower. ¢ — Screw shaft ¢ Pillow shaft ¢ — Sub torsion bar axle

Cam follower Guide rail

Pillow screw Restriction plate

Screw shaft

I ce i aa fe] IN| @, | > ? o7™ =>

Ss} oe SASL | a _ ai "

i Sub-torsion bar axle 7

Page 36

7-8-3 Inspecting the Pillow Unit

WARNING Make sure that the power is turned OFF. If work is to be carried out with the covers removed, take care not to trap hands or fingers in the mechanism.

When greasing the step-lock, inspect the pillow assembly for any problems.

  • Release the step-lock and swing the steps to the left and right, and check the pillow units for any wear. Also check that the Hex Head Screws (M14x45) are tight.
  • Swing the steps left and right, and check that the main torsion bar is secure. Also check that the Hex Head Screws (M10x25) are tight.
  • Reassemble the vac-forms and control panel. Remember to connect the connector when refitting the control panel.

Hexagonal bolt (M10 x 25) AS.

Main torsion bar

Pillow unit

Page 37
  • TROUBLE SHOOTING

Ensure that the power is turned OFF before making adjustments or replacing parts.

If none of the items below correspond to your problem, or if the problem is not corrected by the treatment described below, contact your dealer for further advice.

Always return PC Boards to your dealer for repair. Never test the PC board for continuity with a multimeter or similar device. The PC Board contains sensitive devices which could be damaged or even destroyed by the internal voltage of such test equipment.

When sending parts for repair, clearly indicate the problem, and send them in secure and adequate packing. Especially in the case of sending PC Boards, wrap them in sponge or bubble wrap prior to packing, so that they do not receive excessive shock.

8-1 General Problems

Symptom Cause Treatment Ref. Page

The machine does not work Switch OFF and back ON. even though the power is ON. Operation is unstable or the | Is the mains supply within Remove any heavy duty machine does not operate 10% of the rated voltage. equipment (air conditioners, correctly. large rides, etc.) from the same power line, and ensure that the supply is within the correct limits.

Have parts been changed. Reinitialize the game. pg21 6-4

The game goes off. Is the mains-in plug secure.

Has a fuse blown. Switch the power OFF and check the mains-in filter fuse and fuses on the PSU board.

8-2 Projector Assy

Symptom Cause Treatment Ref. Page

There is no picture on the Monitor switched OFF. Check ON/OFF switch on front monitor. of monitor.

Is the signal loom connected properly. Check SCART connector is secure and connected to the blue auxillary connector.

Page 38

8-3 Header Assembly

SymptomCauseTreatmentRef. Page
The fluorescent lamp doesIs the connector loose orConnect the connectorpg44
not come on.disconnected.securely.schematic
Is the fluorescent tube orReplace tube or starter.pg25 7-2

starter burned out.

8-4 Mast Assembly

SymptomCauseTreatmentRef. Page
There is no sound from als a connector loose orConnect the connector.pg44,
speaker.disconnected.schematic
ls the volume too low.Adjust volume setting.pg18 6-3-4
"WARNING!" is displayed.Is a connector loose orConnect the connector.pg44,

the step lock does not work. | disconnected. schematic

Is a fuse blown. Check and replace fuse on PSU board.

Pushbutton lamp does notIs a connector loose orConnect the connector.pg44
light.disconnected.schematic

Is the lamp loose in the holder. | Insert lamp properly. pg26 7-3

Is the lamp burned out.Replace lamp.pg26 7-3

8-5 Step Assembly

SymptomCauseTreatmentRef. Page
The step control does not work. | Is a connector loose orConnect the connector.pg44

disconnected. schematic Has the game been initialized. _| Initialize the game. pg21 6-4

Is the control pot broken.Perform the switch test topgi6

check control. 6-3-3-1

Replace the control pot. pg28 7-5

The tilt control does not work. | Is a connector loose orConnect the connector.pg44

disconnected. schematic Has the game been initialized. _| Initialize the game. pg21 6-4

Is the control pot broken.Perform the switch test topgi6

check control. 6-3-3-1

Replace the control pot. pg30 7-6

Page 39
  • PARTS
WARNING: Many of the parts used in this machine, including metal work, have been manufactured to special specifications. To ensure continuing safety and correct operation, replace only with genuine MAMECO parts.

ITEM DESCRIPTION PART No.

1HEADER ACRYLIC30000219
2HEADER VAC-FORM - RHS45000580
3HEADER VAC-FORM - LHS45000579
4HEADER METAL HOUSING45000582
5HEADER RETAINING BRACKET45000583
6HEADER ACRYLIC RETAINING BRACKET45000581
7HEADER VAC-FORM DECAL LHS/RHS40000266
8FLUORESCENT TUBE ASSEMBLY98000016
Page 40

ITEM DESCRIPTION PART No

1PHILIPS 46" PROJECTION MONITOR84000003
2PROJECTOR CABINET SIDE DECAL - LHS/RHS.40000264
3ALPINE RACER PCB ASSY - SYSTEM 22XAR-PCB
4SMPSU 5v/30A - 12v/5A,83000004
5ELKAY BLOCK 5 WAY66000014

FUSE 1%" 2A QUICK-BLO 63500504

8FUSE 1%" 3A SLO-BLO.63500547
7BRIDGE RECTIFIER 25amp71000040
8TRANSFORMER67700019
93 CHANNEL POWER AMPLIFIER45000725
10|SCHAFFNER MAINS-IN FILTER,66000016
1ADJUSTABLE FOOT M16x9588300079
12|SWIVEL CASTOR 75mm59000005
13|REMOTE PERSPEX COVER39000891
14|PROJECTOR CABINET FRONT DECAL40000265
Page 41

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 42

ITEM DESCRIPTION PART No.

1MAIN BASE METALWORK45000585
2MAIN BASE EXTENSION ARM - RHS45000586
3MAIN BASE EXTENSION ARM - LHS45000587
4MAIN BASE EXTENSION ARM VAC-FORM - LHS45000588
5MAIN BASE EXTENSION ARM VAC-FORM - RHS.45000589
6SNOW FIELD VAC-FORM - LHS45000590
7SNOW FIELD VAC-FORM - RHS45000591
8SIDE WOOD - LHS.37100078
9SIDE WOOD - RHS37100079
10SIDE WOOD DECAL - LHS.40000267
1SIDE WOOD DECAL - RHS40000268
12COIN TOWER45000592
13PLAY INSTRUCTION DECAL40000276
15FRONT CENTRE EXTENSION BOX45000595
16PROJECTOR/BASE JOINT BRACKET - LHS/RHS45000596
17FRONT EXTENSION BOX - LHS/RHS45000597
18REAR EXTENSION BOX - LHS/RHS45000598
19STEP ON FLOOR BASE45000599
20STEP ON FLOOR BASE SAFETY DECAL40000269
21FLOOR BASE SUPPORT BRACKET - LHS/RHS45000600
22FLOOR BASE SECURING PLATE45000601
23SKI POLES FRONT SUPPORT BAR45000602

SKI POLE - LHS 45000710

*SKI POLE - RHS45000711
25SKI POLES FRONT SUPPORT BAR CLAMP45000604
26SKI POLE GRIP BAR - LHS/RHS45000605
27SKI POLE GRIP WASHER45000606
28SKI POLE/GRIP BAR JOINT - RHS45000607
29SKI POLE/GRIP BAR JOINT - LHS.45000608
30FRONT CENTRE TOP COVER PLATE45000609
31SNOW FIELD VAC-FORM SUPPORT BRACKET REAR - RHS.45000611
32SNOW FIELD VAC-FORM SUPPORT BRACKET REAR - LHS45000610
33SNOW FIELD VAC-FORM REAR SECURING BRACKET45000612
34BASE EXTENSION ARM VAC-FORM TOP FIXING BRACKET45000613
35BASE EXTENSION ARM VAC-FORM LHS/RHS FIXING BRACKET45000614
36SKI POLE DECAL40000270
37MAST SIDE VAC-FORM LOWER KICK BRACKET45000615
40.SWIVEL CASTOR - 75mm59000009
41SWIVEL CASTOR - 50mm59000001
42ADJUSTABLE FOOT M20x70mm25000010
43SKI POLE GRIPS (pair) - BLACK45000617
Page 43

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 44

ia P A °

elle q

Ce _— 2)

ITEMDESCRIPTIONPART No. |[ITEMDESCRIPTIONPART No.
1[MAIN MAST METAL WORK4500064321[JOINT AL-050-12‘45000667
2__|MAST FRONT COVER VAC-FORM4500064422|PLAY INSTRUCTION ACRYLIC30000220
3__|MAST SIDE VAC-FORM - LHS4500084523|CONTROL PANEL DECAL40000271
A| MAST SIDE VACLFORMSRESainda24|FRONT CLOSING BRACKET COVER PLATA 45000662
5_|GONTROL PANEL VAG-FORM4500064725|SPONGE RETAINING BRACKET45000663
6_|SPEAKER MESH FRONT SUPPORT BRACKET | 45000648leat7258
7_|LOUDSPEAKER WOODEN CABINET3710008127WgOINT AL-05041075000666
8[LOUDSPEAKER GRILLE45000649
28|LIR STOP BUMPER K1-4045000664
9[LOCKING PLATE GUIDE RAIL45000650

29 | ADJUSTABLE FOOT M16x95 88300079 10 | THREAD ROLLED DRIVE SHAFT CS-16v149 | 45000715 30 [LOCKING MOTOR 24Vde-350.8RPM-0.221A] 45000714 11 [LIMIT MICRO SWITCH MOUNTING BRACKET | 45000652

31[LIMIT MICRO SWITCH V1541C2560000012

12 |FRONT CLOSING BRKT SUPPORT BRACKET | 45000653

73|PRONT CLOSING BRAGKETqe00085432[FAN SWITCH MOUNTING BRACKET45000697
7a[togmina PLATEFeooess33|PUSHBUTTON MCPB - RED60200247
15|THREAD ROLLED DRIVE GUIDE450006562PUSBBUTTON APE = YELEOW60200227
te[URPOT COVERreer35|LOUDSPEAKER 5%" FULL RANGE62000065
17|WOODRUFF KEY 25x4x44500065937[AXIAL FAN 130mm67000074
18 | SPEAKER GRILLE SPONGE4500066038|SUB BASS DRIVE SPEAKER - 6%"62000068
19[PLAY INSTRUCTION MOUNTING BRACKET — | 4500066139|SUB BASE SPEAKER GRILLE45000701
20[JOINT L-0504500066840|SUB BASS WOOFER CABINET37100084
Page 45

gi i ate 5 { \eizzzzzzzz7777 nN HT) N S

Page 46

ITEM DESCRIPTION PART No

1STEP ASSY MAIN METAL STRUCTURE45000618
2STEP TRAY ASSY45000619
3STEP VAC-FORM - FRONT45000620
4STEP VAC-FORM - REAR45000621
5STEP RUBBER45000622
6ROSTA SPRING BRACKET - FRONT 38x6045000623
7ROSTA SPRING BRACKET - REAR 38x6045000624
8ROSTA SPRING SWING BRACKET 38x6045000625
9STEP CENTERING ARM45000626
10STEP RUBBER RETAINING BRACKET45000627
1STEP SWING BEARING45000628
12STEP SWING BEARING SPACER45000637
13SWING L/R POT MOUNTING BRACKET45000628
14EDGES POT MOUNTING BRACKET45000629
15STEP LOCATING PLATE - UPPER45000630
16STEP RUBBER SUPPORT BRACKET45000631
17EDGES POT COVER BRACKET45000632
18ROSTA SPRING BRACKET45000639
19ROSTA SHAFT BEARING BRACKET - TOP45000640
20ROSTA SHAFT BEARING BRACKET - BOTTOM45000641
21BEARING LFB-141045000642

ROD EYE RBL-6-D 45000633

*2CONNECTING SHAFT 160x845000634
23ROSTA SPRING DRS38x6045000572

24 ROSTA SPRING DRS27x100 XEHO09-262-262

25ROSTA SPRING DRS18x3045000573
26ROSTA SPRING DRS18x5045000574
27ROSTA SPRING RETAINING BRACKET BR-1845000575
28PILLOW BEARING UCP-20845000635
29ROLLER BEARING CF12-1-A45000636
30POTENTIOMETERX008-023
Page 47

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 48

10.SCHEMATICS

MONITOR CABI H i i i a

:F438culPSU/PCB

ee aeown ij i i | | HEADER ASSEMBLY | Trane 4 i a : PINK | | 8 peoy

eel Ww

tyBLUE“-

He

i |lsBLUE7 Seri
iitBue—

| | - sea i ! i i i Fi eas H _ : 2

!|penun F224 S/B
iy|ol
gceNyve{
islusau ul 3B uGee et
i2| Sle) 2] S| 3) ele|

i ! i ! athientiieeniienitaeenanenaie

i; |56

1 AUDIO IN - L/R @]

4a{t‘AUDIO IN + 3[3

ee eat

i]}aiaLEFT SPEAKER | 5 | 5.
i||ici Seeacer

i ici seracee " Se te

!Styne SCART LP seo ony| |UBB;—

47 Ohn i}

i!aa te| AMPLIFIER ASSY
'm4te eeL|_AMPLIFIER ASST
IVGNDdele‘s
!HeyBea=
|iain46 11aBLUE:ete
:|WHITE,ras
!@BLACK
i! 46YELLOWao
i | PROJECTOR|oacans

i a iG MONITOR i

i RET ee nee —e

ee fates

tts 1 SMPSU ‘GND 66 a

INPUT HSCHAFFNER MAINS-IN FILTERERLEmeeHey tt

BROWN |

GRNAYEL,tFILTERI T+

ALL EARTH WIRES GREEN, YELLOW

Page 49

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 50
FT URPLEluaMAST ASSEMBLYeo
ORANGETHct*
BLACKeterareL
PINKJS13ele=
GREEN,Jfa tata4
‘WHITE,Ss {5La tat

rar +1 |p | 717 = ate PLAY PANEL

EEE too U1 [iL GRY/BLK 12 hie BRN/VHL 13113 TRGABLL 44 [it ORG/BLK isis

ORG/RED BLUE L pt BROWN ‘WHI/RED ere fore) RED/GRN GRMN AWEL STEP LOCK

BLU AditeaeFAN SWITCH
ELLOZhemnoo

GRNZYEL >

Ti g ar g 313 4 ta 8 S15

raw

EARTH,eleRe ee ee

GRN/YEL 313 io Ho

Jeeafi133
TLGREENleheanTIEor
=e PALE2 {2ateHe
3 PURPLEatsSTsete
WHI/YEL4}444

=e WHI/Gey Sg ee eee 2 {BLACK 3 $+ Gov WHI

Taf we Zao—88Avel

PSL WHI/eED L

Ha Dwe7oe6ete‘SWING‘
HI/ELK313NB. 1K ohms

GRN/YEL COIN TOWER_A

J35

Ttfs

ete jet

PF} peownral71

“2 ORANGE 44 - S1 GREY, S15

= [ReD/BLACK6 teSERVICE BRACK
7S TRED/BLUE,126ZZ CASHFLOWa

PINK/BROWN Tt

To TBLACK313Te es

3 ata ae S15 24? Ete a7 348 ele ats

ss

FRAME ASSEMBLY

Page 51

| CONTROL PANEL ASSEMBLY

e | | 7 [oo ES) Oo netrsion SUB BASS SWITCH Lk a |

he

SELECT SWITCH > | chr aE SRE

i (©)

00 _sareTy sw rant | (S) «a! SAFETY Sw (Rear) SELECT | SWITCH (RD

———____#— FREE Sw se ick sw TO

te t}—————gg BS ypemre eo
rae2a 42> VREi
aiaEDGEi

NB. 1K ahs ;

i

i

i STEP ASSEMBLY i

i

= i ER_ ASSEMBLY :

“eo sevice|;

levolt !

6 test|2dwotti
E BRACKET|4 4!
—JPINK F3737
METER|PINK 3-4i

YEL/ELK_}S75 i Se 66 77 i ate MARS i 313 CASHFLOW i io {10 SINGLE i TL CHANNEL i Sean i 1313) 44 [4 i 15115 i 16 [16 77 i 1218 i 13 [19 i

i