CATHODE RAY TOMES

Spin the Spin

Spin The Spin (Namco) · Manual · 64 pages · 37 sections · original scan

Page 1

Mnamco

SPIN THE SPIN

Operators Manual

IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY

AT ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY.

Part No. 90500100A

Page 2

PORTABLE APPLIANCE TESTING

Please Note:

During testing of the machine with a portable appliance tester the insulation test will show a failure due to the fitting of two VDRs between Live/Earth and Neutral/Earth.

These components have been fitted to safeguard against high voltage surges that may occur on the mains supply to the machine and to comply with the EMC regulations.

To conduct an insulation test on this machine, the VDRs must be isolated from the circuit first.

Ensure that the VDRs are reconnected after the insulation test has been completed and before the machine is placed back into service.

The VDRs used have been specified and tested as safety critical components.

Page 3

WHEN INSTALLING

ENSURE THAT THE MACHINE IS LEVEL AND STABLE BY RAISING AND ADJUSTING THE LEVEL ADJUSTERS.

FAILURE TO COMPLY MAY CAUSE THE BALL TO NOT SPIN CORRECTLY OR THE TILT SWITCH TO MALFUNCTION.

Adjusting the Level Adjusters

When the machine is in it’s final position, lower the four level

adjusters, with a spanner, so that the castors are raised from the floor by approximately 5mm and the machine is level. Tighten the lock nuts with a spanner to ensure that the level adjusters do not move.

U

Castor ™.. ) Level Adjuster

If the machine is installed on a smooth or shiny floor, it is recommended that rubber pads are fitted under each adjuster to prevent the machine from moving when being played.

Page 4

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private or public use, without permission from NAMCO EUROPE LIMITED.

While the information contained in this manual is given in good faith and was accurate at the time of printing. NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.

This machine has been manufactured in accordance with Eiropean Community Directives, and has been tested and complies with the Directives 89/336/EEC and 72/23/EEC by the application of EN55014, EN55104 and EN60335-1 standards (see front of manual) and as such bears the C€ marking. Any changes or modifications to this machine must be in accordance with the European Directives. Any unauthorised changes to this product, may contravene such Directives.

Under some conditions of extreme external interference, e.g. radio transmissions, electrostatic discharge or mains borne transients, some degradation of performance may occur. However the machine will recover normal performance once the source of the interference has ceased or been removed.

Note:- If the game processor resets due to an interuption or reduction of the mains voltage any credits established may be lost.

This game is not a machine as defined by the Machinery Directive 89/392/EEC

SAFETY WARNING

In order to use this machine safely, be sure to read this Operators Manual carefully before installation, adjustment or use of this machine.

Whenever the owner of this machine entrusts dis-assembly, installation, adjustment or routine maintenance to another person, the ‘owner should ensure that that person read the appropriate precautions and relevant sections of this manual before stating work.

In order that no accidents occur when the machine is in operation, strictly follow the notes on safety as described below.

This manual along with the Installation Manual (where applicable) form an integral part of the equipment and must be available to the operating and service personnel at all times.

This machine is for indoor use only and should only be used for the purpose intended.

Namco Ltd. bears no responsibility for accidents, injury or damage resulting from unauthorized changes to, or improper use of this machine.

SAFETY NOTES

The following safety notes are used throughout this manual. Familiarize yourself with each of these notes and its meaning before installing, servicing or making adjustments to this machine.

WARNING /\ Warning denotes a hazard that could result in injury or death. Do not proceed beyond a
warning note until the indicated conditions are fully understood and met.
CAUTION (1) Caution denotes a hazard that could result in damage to the machine. Do not proceed beyond a
warning note until the indicated conditions are fully understood and met.

GENERAL SAFETY CONSIDERATIONS

Only operate this machine after checking that it has been installed correctly and in accordance with the manual.

Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There are warning notices to keep hands and feet clear of moving parts, however if the operator feels that a person is in any danger, he should warn that person accordingly.

The warning notices must always be kept in good condition and replaced if worn, so that customers can read them clearly.

If there is an error or problem with the machine, operation must be stopped immediately and the problem rectified before any further use.

Installation, service, adjustment or routine maintenance should be carried out by suitably qualified persons only.

For continued protection against fire hazard, replace the mains-in fuses with the same type and rating. The use of other fuses or material is prohibited.

To prevent possible electric shock due to failure, this machine MUST be fitted with a securely connected EARTHED plug.

If at any time the mains supply lead becomes damaged, it must be replaced immediately.

Do not turn the power switch ON until the machine has been installed correctly. OPP BP BEB EP BBE

Before connecting the machine to the mains supply, ensure that the machine is set for the correct voltage and that the correct fuses are fitted.

Page 5

Va Maintenance zone

NOTES ON INSTALLATION

A\ NEVER turn the power to the machine ON until installation has been completed. Unit

In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected earthed plug

©) _Inorder to avoid damage to the machine due to mis-operation, ensure that the voltage of the mains supply is 230volts AC. SOOO SF oe, SS VOR. SR SOS

Note: If the location of this machine has a polished floor, it is recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor.
Note: In order to gain access to the Power Supply and CPU assemblies, make sure that the rear of the machine is separated from a wall or other machine by at least 500mm.

Playing zone ~\

S

MOVING THE MACHINE.

A This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface.

A\ The overall height of the machine, with the Header Assembly fitted, is 1860mm. Take care of any overhead obstructions. (e.g. Light Fittings, Electric Cables etc.)

REMOVING AND REPLACING PARTS

Adjustments or maintenance on this machine should be carried out by suitably qualified personnel only.

Do not make any alteration to this machine without prior approval. Doing so could cause unforeseeable

danger.

Only parts specified by Namco Europe Ltd should be used when replacing or repairing parts. (Including screws).

Ensure that the power to the machine is turned OFF before commencing any maintenance work. (Trouble shooting, repairs etc.)

If performing work not described in this manual, be sure to contact your distributor for instructions, as no responsibility will be accepted for damage or injury.

Make sure that the machine is switched OFF before connecting or disconnecting any plugs or connectors. >EeP BP bP BP BB

When removing the mains connector from the machine, or the mains plug from the wall outlet, always grasp the plug and not the cable.

Page 6

@ Dieses Dokument darf in keiner Weise vervielfailtigt werden. Jegliche Tonautnahmen sowie die Speicherung auf Datentrager (Suchsysteme), die Weitergabe oder sonstiges Kopieren fir den gewerblichen und privaten Gebrauch sind untersagt und bediirfen der vorherigen Genehmigung durch NAMCO EUROPE LIMITED.

Die informationen in diesem Handbuch entsprechen den Tatsachen bei Drucklegung. NAMCO EUROPE LIMITED behalt sich jedoch das Recht zu Anderungen ohne vorherige Bekanntgabe vor.

Dieses Gerat tragt das CE-Zeichen und wurde gema8 den EU-Richtlinien produziert. Es erfillt die Richtlinien 89/336/EEC und 72/23/EEC und Standards EN 55014, EN55104 und EN60335-1 (s. Deckblatt des Handbuches). Alle Veranderungen an diesem Gert missen in Ubereinstimmung mit den EU-Richtlinien erfolgen. Nicht genehmigte Veranderungen an diesem Gerat verstoBen gegen diese Richtlinien.

Extreme auBere Stérungen, wie z.B. durch Radiobetrieb, elektrostatische Entladung oder zeitweilige Netzschwankungen kénnen zu einer Leistungsminderung fihren. Sobald diese Faktoren jedoch ausgeschaltet oder beseitigt wurden, erreicht das Gert seine normale Leistung.

Achtung! Falls der Spielprozessor auf Grund von Netzunterbrechungen oder Abnahme der Netzspannung aussetzt, kann es zum Verlust von Spielkrediten kommen.

Dieses Gert fallt nicht unter die Maschinen-Richtlinie 89/392/EEC

SICHERHEITSHINWEISE

Um einen ordnungsgemaBen Betrieb dieses Gerates zu gewahrleisten, muB vor Aufstellung, Inbetriebnahme und Gebrauch das Handbuch sorgfaltig gelesen werden Sobald der Besitzer dieses Gerates die Demontage, Aufstellung, Inbetriebnahme oder den Service einer anderen Person ibertragt, muB er sicherstellen, daB diese Person vor Arbeitsbeginn die nétigen Sicherheitshinweise und die dazugehdrigen Kapitel des Handbuches liest und versteht. Um jegliche Unfalle wahrend des Betriebes zu vermeiden, mussen obige Hinweise strikt befolgt werden. Dieses Handbuch sowie das spezielle Gerate-Handbuch (wenn vorhanden) gehéren zum Gerat und mussen dem Betreiber und Wartungspersonal stets zuganglich sein. Dieses Gerat ist ausschlieBlich fir den gewerblichen Gebrauch in geschlossenen Réumen bestimmt und darf nur dort betrieben werden. NAMCO LTD. dbernimmt keinerlei Haftung far Unfalle, Verletzungen oder Beschadigungen, die auf nicht genehmigte Veréinderungen oder unsachgemaBen Betrieb des Gerates zuriickzufihren sind.

SICHERHEITSHINWEISE

Folgende Sicherheitsbegriffe werden im gesamten Handbuch benutzt. Machen Sie sich daher bitte vor Inbetriebnahme, Wartung und Durchfiihrung von Einstellungen am Gerat mit diesen Warnhinweisen vertraut.

WARNUNG /\ WARNUNG bezeichnet eine Gefahrenquelle fr Leib und Leben. Erscheint dieser Warnhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklarungen vollstandig verstanden und befolgt wurden.

VORSICHT (1) VORSICHT bezeichnet eine Gefahrenquelle fir die Beschadigung des Gerdites. Erscheint dieser Warhinweis, darf erst weitergearbeitet werden, wenn die entsprechenden Erklarungen vollstandig verstanden und befolgt wurden.

ALLGEMEINE SICHERHEITSHINWEISE

Das Gerat darf nur betrieben werden, nachdem es vorschriftsm4Big und in Ubereinstimmung mit dem Handbuch aufgestellt wurde.

Das Gerat bewegt sich wahrend des Spielbetriebes, somit verandert sich der Abstand zwischen feststehenden und beweglichen Teilen. Warnschilder verweisen darauf, fur Hande und FiBe einen gebihrenden Sicherheitsabstand einzuhalten. Sobald eine Person in Gefahr ist, muB der Betreiber sie warnen.

Die Warnschilder missen in gutem Zustand sein und ersetzt werden, wenn sie nicht mehr gut lesbar sind

Bei Auftreten eines Fehlers oder Problems muB das Gerat sofort abgeschaltet werden und darf erst nach fachgerechter Behebung des Fehlers wieder in Betrieb genommen werden.

Aufstellung, Service, Einstellungen und Wartung darfen nur von dafir qualifiziertem Fachpersonal durchgefihrt werden.

Zur Vermeidung von Feuer, defekte Sicherungen nur durch vorgeschriebene Sicherungen ersetzen. Die Verwendung von andersartigen Sicherungen oder unterschiedlichem Material ist untersagt.

Zur Vermeidung von Elektroschlagen muB dieses Gerat mit einem ordnungsgemaB geerdeten Netzstecker versehen sein

Bei Beschadigungen des Netzteiles muB dieses umgehend ersetzt werden.

Gert erst nach abgeschlossener Aufstellung einschalten. OP BP BBB BBE BP B&

Vor Einstecken des Netzsteckers bitte sicherstellen, daB Netzspannung und Geratespannung dbereinstimmen, und die vorgeschriebenen Sicherungen verwendet wurden.

Page 7

A

0)

Hinweis:

Hinweis: HINWEISE ZUR AUFSTELLUNG Maliinanise zone

NIEMALS das Gerat einschalten bevor die Aufstellung véllig abgeschlossen ist. Unit

Zur Vermeidung von Elektroschlagen muB das Gerat mit einem ordnungsgemaB geerdetem Netzstecker an die Stromversorgung angeschlossen werden

Zur Vermeidung von Beschadigungen durch Fehibetrieb am Gerat sicherstellen, daB die Netzspannung 230 Volt betragt.

Ist das Gert flr einen Aufstellplatz mit glattem FuBboden bestimmt, missen die Standbeine mit Gummiplattchen unterlegt werden, damit das GerAt fest steht und nicht auf dem Boden hin- und herrutscht.

Zu Reparaturzwecken am Netzteil und den CPU-Komponenten muB die Rickseite des Gerates mindestens 50cm von anderen Geraten und der Wand entfernt sein. Playing zone

S

Zum leichteren Transport ist das Gerat mit Rollen ausgeriistet. Daher besondere Vorsicht auf abschussigem Boden.

Die Gesamthohe de Gerates betragt 1.86m. Daher Vorsicht bei tiefer hangenden Beleuchtungskorpern.

> P PRP BP Be B&B AUS- UND EINBAU VON KOMPONENTEN UND TEILEN

Aufstellung, Service, Einstellung und Wartung diirfen nur von dafiir qualifiziertem Fachpersonal durchgefiihrt werden.

Es dirrfen keierlei Veranderungen ohne vorherige Genehmigung am Gerat vorgenommen werden. Zuwiderhandlungen stellen eine Gefahrenquelle dar.

Fir die Repartur dirfen nur Originalersatzteile (incl. Schrauben) von NAMCO EUROPE LTD. verwendet werden.

Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muB der Netzstecker gezogen werden.

Bei Arbeiten, die nicht in diesem Handbuch beschrieben werden, muB vorher der Handler zu Rate gezogen werden, da sonst keinerlei Haftung bei Beschadigungen und Verletzungen ibernommen wird.

Vor der Montage oder dem Entfernen von Steckverbindungen und Steckern muB das Gerat ausgeschaltet werden.

Bei Ziehen des Geratesteckers oder des Netzsteckers aus der Wandsteckdose stets den Stecker greifen und nicht das Kabel.

Page 8

©

No se permite la reproduccién total ni parcial de esta publicacién por ningun medio mecanico, fotografico o electronico, grabaciones fonograficas, ni su almacenamiento informatico, su transmision o su copia, ya sea para uso public o privado, sin permiso de NAMCO EUROPE LIMITED.

Si bien la informacion contenida en este manual se da de buena fe y es correcta en el momento de su impresion, NAMCO. EUROPE LIMITED se reserva el derecho de hacer cambios y alteraciones sin previo aviso.

Esta maquina ha sido fabricada segiin las directrices de la Comunidad Europea, ha sido probada, y se ajusta a las directrices 89/336/EEC y 72/23/EEC, mediante la aplicacion de los estandares EN65014, EN65104 y EN60335-1 (véase cubierta del manual) y por ende lleva el sello de la C.E. Cualquier cambio 0 modificacion que se haga a esta maquina ha de ajustarse a las. directrices de la Comunidad Europea. Cualquier cambio no autorizado hecho al producto pudiera contravenir estas directrices.

Bajo ciertas condiciones de extrema interferencia externa, p. ej. transmisiones de radio, descargas electrostaticas u oscilaciones de la red eléctrica puede tener lugar un descenso del rendimiento. No obstante, la maquina recuperara su rendimiento normal una vez que la fuente de interferencias sea retirada 0 cese de producirlas.

Nota: Si el procesador de juegos se reinicializa a causa de caidas o interrupciones en la alimentaci6n eléctrica, se perderan todos los créditos. Este juego no se ajusta a la definicion de maquina de la Normativa de Maquinaria 89/392/EEC

AVISOS DE SEGURIDAD. Para utilizar esta maquina con seguridad, lea cuidadosamente este Manual de Operador antes de proceder a la instalaci6n, ajuste 0 uso de esta maquina. Cada vez que el propietario de esta maquina confie a terceros su desmontaje, instalacion, ajuste o mantenimiento rutinario debera asegurarse de que tales personas lean las precauciones adecuadas y las secciones relevantes de este manual antes de comenzar su trabajo. Para a no ocurra accidente alguno mientras la maquina se encuentre en funcionamiento, siga estrictamente las notas de seguridad tal como mas adelante se describen. Este manual, junto con el Manual de Instalacion (cuando proceda), forma parte integral del equipo y debe estar a disposicion del personal de mantenimiento y operacién en todo momento. Esta maquina es Unicamente para ser usada en interiores, y solo debe usarse para aquello para lo que ha sido creada. Namco Ltd. queda exenta de cualquier responsabilidad por accidentes, heridas o dafios causados por cambios no autorizados 0 uso indebido de esta maquina.

NOTAS DE SEGURIDAD.

En este manual se usan las notas siguientes. Familiaricese con cada una de ellas y su significado antes de instalar, revisar, o hacer ajustes en esta maquina.

AVISO A\ Aviso sefiala un riesgo que puede ocasionar lesiones 0 la muerte. Tras ver esta nota, no continue hasta entender completamente y cumplir las condiciones exigidas.

PRECAUCION. (1) — Precaucién sefiala un riesgo que puede ocasionar dafios a la maquina. Tras ver esta nota, no continue hasta entender completamente y cumplir las condiciones exigidas.

CONSIDERACIONES GENERALES DE SEGURIDAD.

Opere sélo con esta maquina tras comprobar que ha sido instalada correctamente y de acuerdo con este manual

Algunas partes de esta maquina se mueven durante el juego; por tanto, hay lugares en que la distancia entre las, secciones méviles y estaticas cambia. Existen notas de aviso indicando que se mantengan manos y pies alejados de las partes moviles. No obstante, si el operador cree que cualquier persona se encuentra en peligro, debe advertir de ello a dicha persona. >be

Las notas de aviso deben mantenerse siempre en buen estado y reemplazarse si estuvieran desgastadas para que los usuarios puedan leerlas con claridad

Si hubiera algun error o problema con la maquina, debe interrumpirse su operacion inmediatamente, y subsanar el problema antes de volver a usarla.

Las revisiones de instalaci6n, los ajustes, y el mantenimiento rutinario deberan llevarse a cabo sdlo por personal cualificado.

Para asegurar una continua proteccién contra riesgo de incendios, asegirese de que los fusibles eléctricos sean reemplazados solamente por otros del mismo tipo y especificaciones. El uso de otros fusibles o material esta prohibido

Para evitar posibles descargas eléctricas por cortes, esta maquina debe estar provista de un enchufe debidamente conectado, con TOMA DE TIERRA.

Si en cualquier momento el cable de alimentacién se dajiara, debera ser reemplazado inmediatamente.

No encienda el interruptor de la maquina hasta que ésta haya sido correctamente instalada. Antes de enchufar la maquina a la red eléctrica, aseguirese de que la maquina esta preparada para el voltaje correcto, y de que se usan los fusibles adecuados. OPP P PBB &

Page 9

Notas :

Notas : Maintenance zone

NOTAS DE INSTALACION.

JAMAS ENCIENDA la maquina antes de haber completado la instalacion. Unit

Para evitar posibles descargas eléctricas, asegurese de que la maquina esta conectada a la red con un enchufe provisto de toma de tierra.

Para evitar dafios a la maquina causados por operacion incorrecta, asegurese de que el voltaje de la red es de 230 voltios, corriente alterna.

Si el lugar donde se instalara la maquina tiene un piso pulido, se recomienda colocar tacos de goma bajo los ajustadores de nivel para evitar que la maquina se deslice por el suelo. ones <S Seed en Ss b ne XK x ie ed One Para acceder a las unidades de Fuente de Alimentacion y CPU, asegurese de que la parte trasera del mueble principal esta separada de muros u otras maquinas al menos 500 mm.

Playing zone

El juego tiene ruedecitas para hacer mas facil su traslado. Tenga cuidado al mover la maquina en una superficie inclinada.

La altura total de la Unidad principal es de 1860mm. Tenga cuidado de que no haya obstaculos p. ej. luces.

> BP BPP BP Be B RETIRAR Y REEMPLAZAR PARTES Y UNIDADES.

Las revisiones de instalaci6n, los ajustes, y el mantenimiento rutinario deberan llevarse a cabo sdlo por personal cualificado.

No realice alteraciones en esta maquina sin aprobacién previa. De hacerlo asi, pueden causar peligros imprevisibles.

Solo deben usarse las partes especificadas por Namco Europe Ltd. para reparaciones o reemplazos (incluidos los tornillos).

Asegiirese de que la maquina esta desconectada antes de comenzar cualquier trabajo de mantenimiento (reparaciones, resolucion de problemas, etc.)

Al realizar trabajos no descritos en este manual, pongase en contacto con su distribuidor para recibir instrucciones. Se declina cualquier responsabilidad por dajios o lesiones.

Asegilrese de que la maquina esta apagada antes de conectar o desconectar cualquier enchufe o conector.

Al retirar el conector principal de la maquina, o la clavija de alimentacion del enchufe de la red, agarre siempre la clavija y no el cable.

Page 10

©) Aucun élément de cette publication ne sera reproduit, ni par procédé mécanique, photographique ou électronique, ni par un moyen d'enregistement phonographique. Ces informations ne seront ni stockées grace un procédé de récupération, ni transmises ou autrement copiées pour un usage publique ou privé, sans l'autorisation de NAMCO EUROPE LIMITED.

Malgré le fait que les informations contenues dans ce manuel soient données de bonne foi et étaient actualisées au moment de leur impression, NAMCO EUROPE LIMITED se réserve le droit de procéder & des changements ou a des modifications sans avis préliminaire.

Ce jeu a été fabriqué en respect des normes de la Communauté Européenne, aprés avoir été testé il repond aux normes 89/336/EEC et 72/23/EEC, en application des standards EN55014, EN55104 et EN60335-1 (voir la couverture du manuel), et comme tel il comporte l'autocollant de conformité avec les normes de la Communauté Européenne. Tout changement non’autorisé sur ce produit pourrait contrevenir & ces normes.

Sous certaines conditions extrémes d'interférence exteme, par example des transmissions radio, des décharges électrostatiques ou bien de interférences passagéres sur le réseau, certaines dégradations ou anomalies peuvent se produire. Le jeu retrouvera cependant son état normal de fonctionnement lorsque la cause de ces anomalies aura cessé ou se trouvera déplacée.

Not Si le processeur du jeu se reprogramme suite a une interruption ou une réduction de l'alimentation, les crédits qu'il aurait pu contenir peuvent se trouver perdus.

Ce jeu n’est pas une machine, telle que définie par la norme sur les machines 89/392/EEC

MESURES DE SECURITE

Afin d'utiliser ce jeu en toute sécurité, bien lire ce manuel d'utilisation avant de procéder a son installation, son réglage ou son exploitation. Si le propriétaire de ce jeu en confie la démontage, installation, le réglage ou la maintenance habituelle & une autre personne, il devra s'assurer que cette personne ait lu les conseils d'utilisation et les passages du manuel se rapportant a ce théme, avant qu’elle ne commence son travail. Afin d’éviter tout accident pendant la durée d’exploitation de ce jeu, se conformer strictment aux conseils de sécurité décrits a la suite. Ce manuel ainsi que le manuel d'installation du jeu (la ou nécessaire) font partie des éléments nécessaires a l'installation de la machine et doivent étre mis a la disposition de l'utilisateur et du personnel de maintenance a tout moment. Ce jeu est uniquement destiné & un usage intérieur et devra étre utilisé comme tel. Namco Ltd. ne sera aucunement tenu responsable en cas d’accidents, de blessure ou de dommage quelconque résultant de modifications non autorisées ou d'usage impropre du jeu.

REMARQUES SUR LA SECURITE

Les termes de sécurité détaillés a la suite seront utilisés tout au long de la lecture de ce manuel. Il convient de vous familiariser aves chacun de ces tetmes ainsi que leur signification avant de procéder a installation, & la maintenace ou au réglage du jeu

AVERTISSEMENT /\ Ce terme annonce un danger qui pourrait éventuellement avoir des conséquences dommageables ou mortelles. Ne pas passer oiitre ce signal jusqu’a ce que les conditions indiquées soient entiérement comprises et effectuées.

ATTENTION O) Ce terme indique qu'un danger menace la machine. Ne pas passer oiitre ce signal jusqu’a ce que les conditions indiquées soient entiérement comprises et effectuées.

CONSIGNES GENERALES MDE SECURITE

A\ Allumer l'appareil seulement aprés avoir vérifié qu'il a été correctement installé, et que les instructions du manuel ont été respectées

Certaines piéces du jeu bougent quand jeu est en fonctionment, il y a donc des endroits oui la distance entre la zone stationnaire et la zone en mouvement change. Il existe des notes de mise en garde pour les mains et pieds sur les pigces en mouvement. Cependant si l'opérateur pense qu'une personne court un danger, il doit I'en avertir. >

Les notes de mise en garde doivent constamment demeurer en bon état et étre remplacées en cas de disparition, afin que le client puisse les lire clairement.

S'il y una erreur ou un probléme avec la machine, l'utilisation doit étre immédiatement interrompue et le probleme résolu avant toute nouvelle utilisation.

L’installation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.

Afin d’éviter un éventuel incendie, s'assurer que les fusibles soient remplacés par le méme type de fusibles et au bon voltage. L'utilisation d'autres sortes de fusibles ou autres matériels est interdite. Pour prévenir une éventuelle électrocution due a un défaut matériel, ce jeu DOIT étre muni d'une prise de TERRE connectée en toute sécurité

Si A tout moment les fils électriques sont endommagés, il faut les remplacer immédiatment

Ne pas mettre le jeu en mode de fonctionnement avant qu’il n’ait été correctement installé. Ob BP BB B&B Avant de connecter la machine au réseau, s’assurer que la machine est installée sous la bonne tension et que les fusibles correspondent.

Page 11
Note:
Note: NOTES D’INSTALLATION Maintenance zone

NE JAMAIS mettre le jeu en marche avant que l'installation ne soit complétement effectuée.

Afin de prévenir une éventuelle électrocution, s'assurer que la machine est connectée au réseau avec une prise de terre reliée selon les normes de sécurité

Afin d’éviter que la machine ne soit abimée suite a une mauvaise opération, s'assurer que la tension sur le réseau principal soit de 230 volts AC.

Si lendroit ou doit étre installée la machine a un sol pdli, il est recommandé de poser des tampons feutrés sous les vérins pour éviter que le jeu ne glisse sur le sol

Afin de facilité l'accés aux CPU at a l'alimentation, s’'assurer qu'il y a

un espace d’au moins 500 mm entre l'arriére du meuble et le mur ou tout autre jeu.

Playing zone

Le jeu est foumi avec des roulettes pour une meilleure mobilité. Prendre garde quand la machine est déplacée sur une surface inclinée.

La hauteur totale de l’assemblage principal est de 1860 mm, prendre garde aux encombrements de la partie supérieure (ex : illuminations du bandeau).

PEEP BP EP BP &

Va DEPLACER ET REMPLACER LES UNITES ET LES PIECES DETACHEES.

L'installation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées.

Ne pas apporter de modifications sur cette machine sans autorisation préalable, faute de quoi cela pourrait entrainer un danger

Seules les piéces détachées Namco Europe Ltd. doivent étre utilsées pour le remplacement ou la réparation de piéces (y compris les vis)

S'assurer que l'interrupteur soit sor OFF avant de commencer tout travail de maintenance (localisation d'une panne, reparations, etc.)

Si dans ce manuel il manque une information pour réaliser un quelconque travail, contacter votre distributeur, car aucune responsabilité ne sera acceptée en cas de domage ou de blessure S'assurer que la machine soit hors tension avant de brancher ou débrancher toute prise ou connecteur

Lorsque l'on manipule la prise au réseau de la machine, ou lorsque les prises principales doivent étre débranchées, saisir toujours la prise, et non le cable.

Page 12

Kavéva pépos avtiig ms éxdoans Sev popei va avanapayOel pe oMoWdH OTE |MZAVIKS ,POTOYPAGIKS H NLEKTPOVIKE [LEGO , H HE HOPE GoVNTIKIs NZoYPaPHaNs Kat obTE Va anoONKEDTE: Le ENaVOPHOTIKO GbaTHHEL , Va HeTASOBEt H Va avttypaget ya SHLdoIG H WioTIK:, ypi}on , opis my adder tag NAMCO EUROPE LIMITED.

Kats avrés or tinpopopies oe avtd to eyyerpidto éxouv Soei we KaAA mioTH KL aKPIBag THY dpa tHs THnMENS , n ETaIpEIA NAMCO EUROPE LIMITED xpatéet to dikaiopa va Kaver onorecdinore adkayés opis erdonoinan,

Ta pnyaviipata éyovv KatacKevactel cdpgava pe Tous dpovc ts Evpamaixys Kowdrytag , Kat Exovv eheyDei coppova pe ToVs VoLoug 89/336/EOK Kat 72/23/EOK pe my aitnon tov ENSS014 , EN55104 Kat EN60335-1 otavtapts (Ses mpoata oto eyze\pid10) Ka ha Exovv to CE onpa . Onoadiinote addayi H petatpom} ce avr to unzévnpa Mpénet va civar copoVa HE ToVs 6povg ts Evponaixiis Kowétntas, Oxorecdinore adkayés yopis ddera ce aut to mpoldv pope’ va mupapei avtOvS TOVs 6poUs.

Ze Kémo1es nepimtdoers vmepPokurje etreprcris RapenPoliig ,7.7, pudlopovixts petaddaets , NreKtpootatiKés pETAPOAEs H MapodtKés EUBOAES , Hmopei va napovaiaotoby KanoLEs aOAOTHTES oTHYMAPOVGIaGN . TldvtMs To jLavNjLE Oa. EMAVEADEL GtHY PLALOAOYLKH RapOVGiaGN Ep dGoV Amy THE mapELPoAAs otapaTHaEI 1h aRopaKpoVOEi .

Enueiaon : Edy yivet reset otov processor tov pn Zavijpatos KaTé TH StapKeIa THE KOpIag RapOZs , RovTOI ToD éxovv KEpdnOei prope: va zaboov.

Avté to naryvidt dev civar pnZavnpa dnos mpoodtopiCerat and tovg dpovg Myzavypdtov 89/392/EOK .

OAHTIEY ALMAAEIAL

Pa thy aapadi xprion tov pngaviiparos , xpEner va. diafdaers to eyLerpisto zpHan mpooEKTIKG MPI THY EyKATaETUGH ,tonoDETHAN A ZpHION TOD aviyporto. Ono Snore © WioxrieNs avto0 Tov LNZavH|UtOs CytdEL ANd KémOI0 Poco Va EyKaTUGTIOEL , Va KaVEL OROLUd!TOTE arLayA H édeyZO povtivas oto ymyavnpia , mpéner va. civat aiyoupos dui ézer StaBdoet Tig Odnyies avTOd tov eyyeIpdiov mpIv va apyioet va SovrE Tpog axopuyiy onotovdirore atuzjpatos Katd THY AeItoupyia. TOV LNZAVHWATOS , avaTHPaS akoAOVBodvTAL OL OdNyiEs AO. divovtat napaKéco . Auté 10 eyze1pidwo ae ovvdvacpd te to eyze1pi610 eyKaréotUaNs (Snov diatiVeTaL) anotedei Eva. OLOKANPOREVO LEpos TOV mapoYov Ka mpénEL va eivat diadésqio 1a thy Aettovpyia Kat to service omoIdrxoTE oTLYLN. Avté to pngavnjia evan ya YpHOn LSVO GE eowtEpIKO ZOpO Kat Oa MPEREL va. YPHOYLOROLEItaI [OVO 1a. Tos A6yOUS yta TOUS omoIoUg KataoKevdathKe. H_eraipeia NAMCO Ltd dev pépet Kapia evddvy ra atuxhpata , mnyés H KatUatpOGés Rov ROPE: Va mPOKANDOdY aNd arAayés Zopic dea Ge H e1sayeyeig avtod tov UNZaviiparos. sag dmg

XHMEIQLEIL AL@AAEIAL

O1 axdhovdes onperdsers aogddcrag ypnowonoodyea pécw avtod tov eyfeiprdion . AtéPuce avtés npooeKTIKG ya. va. yiveL Kotavonté 10 vonHG Tous EPL THY EyKUTHOTAGN , GEpfIs H onoLUdH|ROTE adAUyH yiver oto AN yZavHLA.

TPOEIAONOIHEH /\ H xposidoroinan apopé Kivévvo 0 onoiog propsi va sivar R6yos Oavarou . Na wy mpozapiiesis o& onoadyrote Kivnon pézpL avtoi or Spor yivovy KatTavonToi.

TIPOZOXH )_ Hxposoxh agope kivsuvo 0 oxoi0g jixopet va xpoxadécer mpOPAnpia oto jngavnpia . Na nv mpoyophosic ot onowdrjxore Kivnon suézpt avtoi o1 Spot yivovv Katavontoi.

EEETAZH PENIKHE AZ@AAEIAD

> Agod éz1 KatavonBei avtd to eyperpidi0 , pévO TétE va AeLToupyeet To UNZavHRA H va yiver EAEYL0s Ep daov Eyer yiver sykatéstacn.

> Mépy tov pyzavipatos petaKwodvrar Kata THY SLpKELA Evdg MAZVIOLOD , éTOL Hate va VRGPZoLV HEpH drov y axdotaGH WETAEH Tov pépovg otdOpevens Kat Toxo KivnoNs va popsi va adAGLEL . Ynapzovv xposdonoujesis va civat ta 7épra kau ta T65LE HaKprd an6 ta pépy nov KWwodvTat, dpos 0 iOKTITHS npéneI Va hEYLEL LAV KAmOLOg KLSDVEDEL Va TOV ELd0TONI|GEL Kal Va TOV aropaxpiver .

Ot xposdonoujosis npéxei va pévovv KaBapés KaL Gt Kaa} KaTéoTUGH dete o nehATMS va TIs LapACEL KaBapG.

Ey vmépyet 2.400¢ mpopiqna pe to pZavHHA., y AeLtoupyia mpénEL va GtapaTast apésas Kat va dtopBGverai to L480s mp_W onovadinote 422 zpHon.

Eykaréotaon , petatpomi a éAeyZ05 povtivas unopsi va yivetan povo ané cLoverodoTpéva drone «

Tia covey} mpootacia and pond , mpéner o1 aspadsies va avtiKaBLotobvTAL [LE {51D THnOD .H 7pron Gi.OV aoqars1dv H aytiKeipévoy anayopsveta. Tia thy axogvyy nieKtpucdv ox 2.670 B.GBys , To pHYZGvHHE TIPETEL va yet mpota evoodei pe yeioon.

Ey kénova ottyy} Katastpagei 9 Kopia napozh , mpénct va avTIKaTaSTaBE! apéows.

Na py avayer to pmyzavnpa (switch ON) pézpr va ézet eyKataotaVE! coors Kat Mhipas.

Tpw thy napox pespatos oto pngavnpa , va eica aiyoupoc S11 ta voltage Kat dkes ot agpéderEs evar caoté evopéva KaL tonolempéva. OBPBPBBBE BB

Page 13

Maintenance zone ZHMEIQLEIS PIA THN ETKATAZTAZH

A TIOTE va pny avéBer to pnyzavnpa cov dev Eyer ohoKANPOOEi eykataotacn. Unit A Tia thy axopuy) niextpkdv cox mpéret To pNZavnna va ézer yeLodet.

  • Tia my axogvy} BAéBns oto uNZavHHA AOYO AAD0g AettOUpyiag , péret apoyi va eivar 230volt AC. EHMEIQSH: Edy to nétopa oto onoio eivat tonodernpévo to pmxavn pa. yavotpaer,civat KOAS Va. inet Eva KOMBAT HoKETAS ya aTOOLy;} jLETaKivnGNs TOD Hnzaviiwatos ev dpa dertoupyias tov.

EHMEIOSH: Ta thy cdKokn apooBacn omy Kvpiag xapogi to CPU apénet n ziow Opta Tov HN ZAVALATOS va anéyer TOVAGOTOV 500MM and tov ToizZ0 h Gio pnzaevyta.

LL Playing zone)

A To pyyavyna civar egodiacpévo pe Kapovia ya THY EdKOAN pETaKivySH Tov.

A To ovvoduKd byos THS KEpadis civar 1860mm . Opdévtics va phy ytvMIoe1 Ge AGpTES K.-T.

ATIOMAKPYNEH KAI ANTIKATAZTALZH MEPON - ANTAAAAKTIKQN

EyKatéotasn , netatpom) ¥ Eeyzoc povtivas wnopsi va yiverai pévo and cLove.dotmpéva drone.

Aey mpénci va yivovtan wetatponés ota jngaviinata opic EyKpion . Mropei va mpoKhnOet anpoPhentos Kivavvos.

Mévo pépy nov dtevxpwiovtar axé thy etaipcia NAMCO EUROPE Ltd propody va zpnomonomPody ya, aytiKatéotacn i emd.6pOoan. (cvATEpL.apPavovre Kat o1 Bides)

Na sivan otyoupa Kict076 to pebpa mpi onoiwdt\rore Sovd.£16 oto pZavnNA.

Eav yiver kéro1a dovds1d oto pnZavana yopic va dtevkpwicerar oto eyye1pidi0 , va emKOWeV|GEIs [IE TOV aytizpécono ya odnyics ati Kapia evdivy Sev Oepoupe ya KataatpOgés i BLOBS. To pmzavqua xpénci va ivan oBysté Kata THY GOvdEGH H anoGbvdcon mpiCas ¥ KovéKtopa. PRPBB BBE

Kara my axopaxpoven tov Kevtpikdy KovéKtop ax6 to unzavana H THs Kpiag mpias , mpéeI va Mavovpe TO mhastiKé Epos Kat 671 70 KaA0S10.

Page 14

@ Nessuna parte di questa pubblicazione pud essere riprodotta con processo meccanico, fotografico o lettronico, né sotto forma di registrazione fonografica, nd pud essere memorizzata in un sistema di salvataggio, trasmessa o in altro modo copiata per uso pubblico 0 privato, senza l'autorizzazione di NAMCO EUROPE LIMITED. Le informazioni contnute in questo manuale sono state date in buona fede ed erano accurate al momento della pubblicazione. Tuttavia NAMCO EUROPE LIMITED, si riserva il diritto di apporre cabiamenti e variazioni senza alcun preawviso.

Questo apparecchio é stato costruito in conformita alle Direttive della Comunita Europea, ed @ stato provato e soddisfa le Direttive 89/336/EEC e 72/23/EEC per l’'applicazione degli standards delle norme EN55014, EN55104 e EN60335-1 (vedi fronte del manuale), e per questo porta il marchio CE. Qualsiasi cambiamento o modifica di questo apparecchio deve essere in conformita con le Direttive della Comunita Europea.

In caso di condizioni di estrema interferenza dall'esterno, per esempio trasmissioni radio, scariche elettrostatiche o transitori sulla linea, pud verificarsi un decadimento delle prestazioni. Comunque l'apparecchio ritornera al rendimento normale quando la sorgente dell,interferenza avr cessato di emettere o sara stata rimossa.

Nota bene: se il processore del gioco “resetta” a causa di una interruzione o diminuzione del voltaggio di linea, un eventuale credito, gia concesso, pud essere annullato.

Questo goco non é una macchina cosi come viene definita dalla Direttiva Macchine 89/392/EEC.

AVVERTENZE PER LA SICUEZZA

Allo scopo di usare questo apparecchio in sicurezza, leggere questo Manuale dell’operatore attentamente prima dell’installazione, regolazione 0 uso di questa macchina. Tutte le volte che il proprietario di questo apparecchio affida lo smontaggio, l'installazione, la regolazione o la manutenzione ordinaria ad un’altra persona, il proprietario stesso deve assicurarsi che quella persona legga le precauzioni necessarie e i paragrafi importanti di questo manuale prima di iniziare a lavorare. Perché non succeda alcun incidente quando la machina é operante, seguire rigorosamente le note sulla sicurezza come specificato piu avanti. Questo manuale insieme con il manuale di installazione (dove si pud applicare) forma una parte integrante dell'apparechio e deve essere disponibile sempre al personale operante e di servizio. Quest macchina deve essere usata solo in interni e deve essere usata solo per gli scopi per cui é progettata. Namco Europe Ltd non si assume responsabilita per incidenti, ferite o damni risultanti da cambiamenti non autorizzati o da uso improprio della macchina.

NOTE PER LA SICUREZZA

Le seguenti note sulla sicurezza sono usate dal principio alla fine di questo manuale. Valutare attentamente ciascuna di queste note ed il loro significato prima di installare, fare assistenza o regolazioni su questa macchina.

WARNING /\ “Warning” evidenzia un rischio di ferita 0 di morte. Non procedere oltre una nota “Warning” finché le avvertenze specifcate non siano completamente capite e conosciute.
CAUTION (4) — “Caution” evidenzia un rischio di danneggiare la macchina. Non proceder oltre una note “Caution” finché le awertenze specificate non siano completamente capite e conosciute.

CONSIDERAZIONI GENERALI SULLA SICUREZZA

Mettere in funzione l’apparecchio solo dopo aver controllato che |’installazione sia stata effettuata correttamente ed in conformita alle istruzioni del manuale.

Parti di questa machina si muovono durante il gioco, quindi ci sono posti dove le distanze tra la parte fissa e quella mobile cambiano. Ci sono avvisi “Warning” di tenere mani e piedi lontani dalle parti mobili, comunque se l'operatore crede che una persona sia in un qualche pericolo, deve avvisare quella persona.

Gli avvisi “Warning” devono sempre essere conservati in buone condizioni e sostituti se consumati, cosicche il cliente li possa leggere chiaramente. Se vi sono errori o problemi con la machina, si deve interrompere il funzionamento immediatamente e risolvere il problema prima di ogni ulteriore uso.

L’installazione, l'assistenza, le regolazioni e la manuzenzione ordinaria devono essere eseguite solo da persone idonee e qualificate.

Per una protezione costante contro il rischio di fuoco, assicurarsi che i fusibili sulle alimentazioni siano solo sostituiti con lo stesso tipo e caratteristiche. L’uso di altri fusibili o materiali é proibito. Per prevenire possibili scosse elettriche dovute a difetti, quest macchina DEVE essere installata con un connettore sicuramente MESSO A TERRA.

In caso il cavo di alimentazione di rete risultasse danneggiato deve essere sostituito immedatamente.

Non accendere la macchina finché la stessa non é stata installata completamente e correttamente. OPP PPB BBP BBE

Prima di collegare la macchina alla rete, assicurarsi che la machina sia preparata per il voltaggio corretto e che siano inseriti i fusibili adatti.

Page 15
Note:
Note: Maintenance zone NOTES D’ INSTALLATION

NON ACCENDERE MAI la macchina finche l'installazione non &

stata completata. Unit 4

Allo scopo di prevenire possibili scosse elettriche, la macchina deve essere obbligatoriamente collegata alla rete con un connettore messo a terra con connessioni sicure.

Per evitare danni alla macchina durante la messa in opera, assicurarsi che il voltaggio della rete sia 230 volts AC.

Il uogo di destinazione della macchina deve avere il pavimento liscio e si raccomanda di sistemare dei cuscinetti di gomma sotto i piedini di livellamento per prevenire lo sciovolament della macchina sul pavimento. RS bs

Kx SSK RS Per garantire l’accesso all’alimentatore e alla scheda madre, assicurarsi che il retro del mobile principale sia separato dalla parete Le o da altre macchine di almeno 500mm. Playing zone

ll gioco é fornito di ruote per rendere pit facile il suo spostamento. Fare attenzione quando si muove la macchina su una superficie inclinata.

L'altezza totale della parte principale é 1860mm, fare attenzione ad eventuali ostacoli sopra la testata ovvero ad eventuali installazioni di luci.

> BPRPBPBP BB RIMOZIONE E SOSTITUZIONE DI GRUPPI E PARTI STACCATE

Liinstallazione, l’assistenza, le regolazioni e la manuzenzione ordinaria devono essere eseguite solo da persone idonee e qualificate. Non apporre alcuna modifica alla macchina senza autorizzazione preventiva. Il fare questo pud causare un pericolo non prevedibile.

Quando si rimpiazza o si riparano delle parti (incluse le viti) si possono usare solo parti approvate dalla Namco Europe Ltd

Assicurarsi che la macchina sia SPENTA prima di incominciare qualsiasi lavoro di manutenzione (guasti, riparazioni etc.)

Se state per iniziare un lavoro non descritto in questo manuale, contattate il vostro distributore per instruzioni poiché non si accetta alcuna responsabilité per danni o ferite. Assicurarsi che la machina abbia l'interruttore nella posizione OFF prima di inserire o disinserire qualsiasi connettore o spina.

Quando vengono rimossi i connettori principali dalla machina oppure la spina dell’alimentazione dalla parete bisogna sempre afferrare il connettore e non il cavo.

Page 16

@)

Ingen del av denne utgivelsen ma reproduseres av noen mekaniske, fotografiske elle elektroniske prosesser, eller i form av fotografiske opptak, og ikke kan det lagres i et gjenvinnbart system, sendt eler kopiert for offentlig eller privat bruk, uten tillatelse fra NAMCO EUROPE LIMITED.

Da informasjonen i denne manualen er gitt i god tru og var korrekt da den ble utgitt, tillegger NAMCO EUROP LIMITED seg retten til A lage forandringer uten varsel.

Denne maskinen er produsert i samsvar med direktiver framsatt av det Europeiske samfunn. Maskinen er testet og samsvarer med direktivene 89/336/EEC og 72/23/eec med anvendelse av EN55014, EN55104 og EN60335-1 standarder (se i begynnelsen av manualen), og derfor beerer CE merket. Hvilken som helst forandring eller modifisering ma skje etter direktivene satt av det Europeiske samfunn. Uautoriserte forandringer pa dette produktet, kan motstride disse direktivene.

Under noen forhold av ekstreme ytre forstyrrelser, f.eks radio sendere, elektronisk utladning eller transiente spenninger, kan man regne med noe senket ytelse. Men maskinen vil oppna normal ytelse nar kilden til forstyrrelsene opphorer eller er fysisk fjernet.

Merk:- Hvis spillets prosessor resettes p.g.a et Kutt eller reduksjon av hovedspenningen kan oppsparte kreditt pa spillet forsvinne.

Dette spillet er ikke en maskin som er definert ved Maskin direktivet 89/392/EEC.

Sikkerhets advarsel.

For & bruke denne maskinen uten noe form for fare, sorg for a lese denne manualen noye for installasjon, justeringer eller bruk av maskinen. Nar eieren av denne maskinen overlater avmontering, installasjon, justering eller rutine vedlikehold til en annen person, skal eieren forsikre seg om at denne personen leser de passende forsiktighetsteglene og relevante deler av manualen for han starter pa arbeidet. For a forhindre at ulykker inntreffer nar maskinen er i drift, folg strengt teksten om sikkethet som beskrevet nedenfor. Denne manualen sammen med installasjons manualen (hvor det er anvendelig) er en intrigert del av utstyret og ma vaere tilgjengelig for drift- og servispersonell til alle tider. Denne maskinen er bare for innendors bruk og skal bare benyttes etter mente hensikter. Namco Ltd. beerer intet ansvar ved ulykker, kvestelse eller skade som folge av uautoriserte forandringer, eller for uriktig buk av maskinen.

Sikkerhets beskjeder.

Folgende sikkerhets punkter er brukt ut denne manualen. Gjor deg kjent med disse punktene og deres mening for installasjon, service eller du utforer noen innstillinger pa denne maskinen.

ADVARSEL /\ Advarsel innebeerer en risiko som kan fore til kvestelse eller dod. Ikke fortsett utover advarslen for den er ordentlig forstatt og mottiltak er igangsatt. FORSIKTIG (f) _ Forsiktig innebeerer en risiko som kan medfore skade pa maskinen. Ikke fortsett utover advarsien for den er ordentlig forstatt og mottiltak er igangsatt.

VANLIGESIKKERHETSTILTAK

Bruk bare denne maskinen etter a ha kontrollert at den er korrekt installert ifolge manualen.

Deler av denne maskinen er i bevegelse under spill, det er derfor plasser hvor avstanden mellom de stillestaende deler og bevegelige deler forandres. Det er plassert skilt med advarsel for a holde hender og fotter borte fra bevegelige deler, men uansett skal operatoren varsle vedkommende hvis han foler at han er i noen form for fare.

Advarsel skiltene ma bestandig holdes i skikket stand og eventuelt byttes ut hvis det oppstar skade pa dem, slik at kunden uten vanskelighet kan lese dem Hvis det er en feil eller et problem med maskinen, ma den straks settes ut av funksjon. Og ma under ingen omstendigheter startes for problemet er rettet pa.

Installasjon, service, justering eller rutine vedlikehold skal bare utfores av kvalifiserte personer.

For fortsatt beskyttelse mot brann, forsikre deg at hoved sikringen bare byttes ut med en av samme type og verdi. Bruk av andre sikringer eller materiale er forbudt. For a forhindre mulige elektriske sjokk grunnet funksjonsfeil, ma denne maskinen vzere ordentlig jordet Hvis ledningen til hoved stromforsyningen skades ma den straks byttes ut.

Ikke sla pd maskinen for den er korrekt installert.

For du kopler maskinen til stromnettet, forsikre deg om at maskinen innstilt for den korrekte spenningen og de riktige sikringene benyttes. OBPBPP BE PB BBE

Page 17

A

0)

MERKNADER: Hvis plassen hvor spillet skal plasseres har polerte gulv

MERKNADER: For a f8 adgang til stromforsyningen og CPU-kort, forsikre Maintenance zone MERKNADER VED INSTALLASJON

Sla ALDRI pa maskinens stromforsyning for installasjonen er fullfort.

For & forhindre eventuelle elektriske sjokk, forsikre deg om at

maskinen er koplet til et stromnett med ordentlig jording.

For a forhindre skade pa maskinen p.g.a. feil bruk, sorg for at spenningen til hoved stromforsyningen er 230Volt AC.

“05 oletes anbefales det at du benytter gummi sko under niva justeringene, for a forhindre at maskinen kan flytte pa seg.

deg om at bakparten av hoved kabinettet er skilt fra vegger eller andre maskiner med minst 500mm.

Praying zone)

Spillet har montert hjul for & gjore det letter 4 flytte pa. Hver forsiktig nar det skal flyttes pa en hellende overflate.

Den totale hoyden pa hoved enheten er 1860mm. veer forsiktig med hoye hindringer som f.eks lysror.

> EP BeBe BBB FJERNE OG UTSKIFTE ENHETER OG DELER.

Installasjon, service, justering eller rutine vedlikehold skal bare utfores av kvalifiserte personer.

Ikke lag noen forandringer pa denne maskinen uten godkjenning. Dette kan medfore uforutsette farer.

Bare deler spesifisert av Namco Europe Ltd. skal benyttes ved utskifting eller reparasjon av deler (dette gjelder ogsa skruer).

Forsikre deg om at strommen er slat av for du pabegynner noe som helst vedlikeholdsarbeid (feilsoking, reparasjon osv.)

Hvis du utforer arbeid som ikke er beskrevet i denne manualen, ta kontakt med din distributor for instruksjon da ikke noe ansvar vill bli akseptert for skade pa maskin eller pa personer.

Forsikre deg om at maskinen er slatt av for du kopler sammen eller tar fra hverandre plugger eller koplinger.

Nar du fjerner hoved koplingene fra maskinen, eller hoved pluggen fra stopselet, ta bestandig tak i pluggen og ikke ledningen

Page 18

@D Niets uit deze publikatie mag worden gereproduceerd door enig mechanisch, fotografisch of electronisch proces, of in de vorm van een fonografische opname, noch mag het opgeslagen worden in een retrieval systeem, doorgezonden of anderszins gekopieerd voor publiek of privégebruik, zonder toestemming van Namco Europe Limited.

Ofschoon de informatie in deze handleiding in goed vertrouwen is gegeven en nauwkeurig was ten tijde van het drukken, houdt Namco zich het recht voor om veranderingen en aanpassingen te maken zonder bericht.

Deze machine is geproduceerd volgens Richtlijnen van de Europese Gemeenschap, en is getest en is in overeenstemming met de Richtliinen 89/336/EEC en 72/23/EEC door de toepassing van de standaards EN55014, EN55104 en EN603365-1 (zie voorin de handleiding) en draagt als zodanig het CE-merk. Enige veranderingen of aanpassingen aan deze machine dienen in overeenstemming te zijn met de Richtliinen van de Europese Gemeenschap. Enige ongeauthoriseerde veranderingen aan dit produkt kunnen in strijd zijn met deze Richtlijnen.

Onder sommige omstandigheden van extreme externe storingen, bijv. radiotransmissies, electrostatische ontladingen of pieken op het net, kan prestatieteruggang optreden. De machine zal echter normaal presteren zodra de storingsbron gestopt of verwijderd is.

Let op: - als de spelprocessor reset a.g.v. een onderbreking of vermindering van de netstroom, dan kunnen opgebouwde credits verloren gaan.

Dit spel is niet een machine zoals omschreven in de Machinery Directive 89/392/EEC.

Veiligheidsopmerkingen Om deze machine veilig te kunnen gebruiken, dient voor installatie, aanpassing of gebruik van deze machine, de Bedieningshandleiding zorgvuldig gelezen te worden. Telkens wanneer de eigenaar van deze machine de demontage, installatie, aanpassing of routine-onderhoud toevertrouwd aan een andere persoon, dient de eigenaar er voor te zorgen dat deze persoon de juiste voorzorgsmaatregelen en relevante gedeeltes uit de handleiding lest voordat hij begint. Om er voor te zorgen dat geen ongelukken gebeuren als de machine gebruikt wordt, dienen onderstaande veiligheidsaanwijzingen Zorgvuldig opgevolgd te worden. Deze handleiding maakt samen met de installatiehandleiding (waar van toepassing) een integraal deel uit van de apparatuur en moet te allen tijde ter beschikking staan van exploitatie- en onderhoudspersoneel. Deze machine is alleen bedoeld voor gebruik binnenshuis en dient alleen gebruikt te worden voor bedoelde doeleinden. Namco Ltd. is niet verantwoordelijk voor ongelukken, letsel of schade die voortkomt uit ongeoorloofde veranderingen aan of onjuist gebruik van deze machine

Veiligheidsopmerkingen

De volgende veiligheidsopmerkingen worden overal in deze handleiding gebruikt. Maak uzelf vertrouwd met deze opmerkingen en hun betekenis voor installatie, het plegen van onderhoud of het aanbrengen van aanpassingen aan deze machine.

WAARSCHUWING A Waarschuwing geeft een gevaar aan dat zou kunnen resulteren in letsel of de dood. Ga niet verder dan een waarschuwingsopmerking totdat de aangegeven omstandigheden volledig begrepen zijn en hieraan voldaan is.

VOORZICHTIG @)_ Voorzichtig geeft een gevaar aan dat zou kunnen resulteren in schade aan de machine. Ga niet verder dan een voorzichtigheidsopmerking totdat de aangegeven omstandigheden volledig begrepen zijn en hieraan voldaan is

ALGEMENE VEILIGHEIDSOVERWEGINGEN

Stel deze machine alleen in gebruik nadat gecontroleerd is of de machine correct en overeenkomstig de handleiding is geinstalleerd. > - Gedeeltes van deze machine bewegen tijdens het spel, waardoor er plaatsen zijn waar de afstand tussen het stilstaande gedeelte en de bewegende sectie verandert. Er zijn waarschuwingsstickers om handen en voeten van bewegende delen af te houden; als de exploitant echter van mening is dat iemand in gevaar is, dan dient hij deze persoon dienovereenkomstig te waarschuwen.

De waarschuwingsstickers dienen altijd in goede staat te worden gehouden en vervangen indien versleten, zodat de klant ze goed kan lezen.

Als zich een fout of probleem voordoet met de machine, dan dient de machine onmiddellijk stopgezet en het probleem verholpen te worden voordat de machine verder gebruikt wordt

Installatie, service, aanpassingen of routine-onderhoud dient alleen uitgevoerd te worden door hierin bekwame personen.

Om blijvende bescherming tegen brandgevaar te garanderen, dient ervoor gezorgd te worden dat de netzekeringen alleen vervangen worden door zekeringen van hetzelfde type en dezelfde sterkte. het gebruik van andere zekeringen of ander materiaal is verboden.

Om mogelijke electrische schokken a.g.v. storingen te voorkomen, MOET deze machine voorzien zijn van een goed vastzittende aardstekker.

Mocht het netsnoer op enig moment beschadigd worden, dan moet deze onmiddellijk vervangen worden.

Zet de machine niet AAN totdat deze correct is geinstalleerd.

Voordat de machine op het lichtnet wordt aangesloten, dient gecontroleerd te worden of de machine op het correcte voltage staat atgesteld en of de correcte zekeringen zijn aangebracht. OPP P BBB B&B

Page 19

© PB)

a Maintenance zone Opmerkingen aangaande Installatie

Sluit de machine nooit aan op de stroomtoevoer totdat de installatie is voltooid. Unit Om mogelijke electrische schokken te voorkomen, dient ervoor

gezorgd te worden dat de machine middels een goed vastzittende ZZ

aardstekker op het lichtnet is aangesloten.

Om schade aan de machine door verkeerd gebruik te voorkomen, dient ervoor gezorgd te worden dat het voltage van het lichtnet 230volts AC € bedraagt. meats measecnteentl 2 estate OKO

OPMERKING: Als de machine op een gladde ondergrond wordt gebruikt, Meee Ree

is het raadzaam rubber matjes onder de stelpootjes te SEM one

bevestigen om te voorkomen dat de machine over de vioer Sd estate gaat glijden. Ieeagactataceetes Ccsucestaeaes SOS SRN se OPMERKING: Om toegang te krijgen tot de voeding- en de CPU- ON % assemblies, dient ervoor gezorgd te worden dat de Naa eens a achterkant van het kabinet minimaal 500mm verwijderd is van de muur of andere machines. - Playing zone

Het spel is voorzien van wieltjes, waardoor het gemakkelijker is om te verplaatsen. Wees voorzichtig als de machine op een hellend viak gereden wordt

De hoogte van het hoofdgedeelte is 1860mm: kijk dus uit voor obstakels zoals lampen.

PBPBBPBP BP B- Verwijderen en vervangen van Assemblies en onderdelen

Installatie, service, aanpassingen of routine-onderhoud dient alleen uitgevoerd te worden door hierin bekwame personen

Maak geen veranderingen aan deze machine zonder goedkeuring vooraf. Dit kan onvoorzien gevaar opleveren.

Alleen onderdelen die door Namco Europe Ltd. zijn gespecificeerd dienen gebruikt te worden bij het vervangen of repareren van onderdelen (incl. schroeven)

Zorg ervoor dat de machine UlTgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.)

Bij het verrichten van werkzaamheden die niet in deze handleiding staan beschreven, dient voor instructies altijd contact opgenomen te worden met de verdeler aangezien geen verantwoording wordt genomen voor schade of letsel. Zorg ervoor dat de machine is UlTgeschakeld voordat pluggen of connectors ingestoken of uitgetrokken worden.

Als het netsnoer uit de machine of uit het stopcontact verwijderd wordt, dient altijd de stekker vastgepakt te worden en niet het snoer.

Page 20

®) Nenhuma parte desta publicacdo podera ser reproduzida por processos mecanograficos, fotograficos, electronicos ou ainda sob a forma de gravacdo sonora nem téo pouco podera ser gravada através de sistemas informaticos transmissiveis ou de outra forma copiados para uso publico ou privado sem autorizagdo expressa da NAMCO EUROPA LIMITADA.

A informagao contida neste manual foi fornecida de boa fé, sendo rigorosa na altura da sua publicagao. A NAMCO EUROPA LIMITADA, reserva-se o direito de proceder a mudangas e alteragdes sem qualquer aviso prévio Esta maquina foi fabricada de acordo com as Directivas Comunitarias Europeias e tem sido testada em conformidade com as seguintes Directivas: 89/336/EEC e 72/23/EEC através dos requerimentos normativos, EN55014, EN55104 e EN60335-1 (ver capa frontal do manual) e como tal sustenta o certificado de marca de CE. Quaisqueres alteracdes ou modificagdes efectuadas nesta maquina deverao ser em conformidade com as Directivas da Comunidade Europeia. Quaisquer alteragdes nao autorizadas a este equipamento poderao infrigir tais Directivas.

O funcionamento normal desta maquina, podera ser afectado debaixo de algumas condicées extremas de interferéncias externas tais como; transmissées via radio, descargas electroestaticas e passagens de corrente na rede de alimentacao. Contudo o seu funcionamento normal sera restabelecido logo que a fonte de interferéncias tenha cessado ou tenha sido neutralizada.

Nota :- Se 0 processador de jogo for inicializado devido a uma interrupgao ou quebra da corrente principal, quaisqueres creditos obtidos poderao desaparecer.

Este jogo por si sé nao contitui uma maquina tal como defenido pelas Directivas de Maquinaria de 89/392/EEC8.

AVISOS DE SEGURANGA Afim de usar esta maquina com seguranga, cettifique-se que Ié este manual de operador atentamente antes de proceder 4 montagem e afinacao ou uso da mesma. Sempre que o proprietario desta maquina confiar a desmontagem, instalagdo, afinagdo ou manutengdo preventiva da mesma a outra pessoa, deverd este assegurar - se que a pessoa em questao Ié as precaugées apropriadas e capitulos relevantes deste manual antes de iniciar o trabalho. Afim de evitar qualquer tipo de acidente quando a maquina estiver em funcionamento, devera seguir rigorosamente os procedimentos de seguranga descritos abaixo. Este manual juntamente com o manual de instalagdo (aonde aplicavel), contituem parte integrante do equipamento e deverao estar sempre disponiveis ao operador e pessoal tecnico de assisténcia. Esta maquina destina-se a ser operada em espacos interiores apenas e a sua utilizagdo deve circunscrever-se somente aos fins previstos. A Namco Ltd. declina qualquer responsabilidade por acidentes, ferimentos ou danos resultantes de modificagdes nao autorizadas ou uso indevido desta maquina.

AVISOS DE SEGURANCGA

Os seguintes avisos de seguranga sao usados através de todo o manual. Familarize-se com cada um destes avisos e respectivos significados antes de instalar, assistir ou efectuar qualquer afinacdo nesta maquina.

PERIGO /\_ Perigo revela uma situacao anormal que podera resultar em ferimentos ou morte. Ndo avance para além de um aviso de Perigo sem que todas as condigées indicadas estejam completamente esclarecidas e resolvidas.

CAUTELA (0) Cautela revela uma situagdo anormal que podera resultar em danos materiais para a maquina. Nao avance para além de um aviso de Cautela sem que todas as condigées indicadas estejam completamente esclarecidas e resolvidas.

AVISOS DE PERIGO

Esta maquina sé devera ser colocada em funcionamento apés ter sido verificado que se encontra instalada correctamente e de acordo com o manual de instrugées. > Algumas partes componentes desta maquina movem-se durante a acg4o de jogo, porconseguinte existem lugares aonde a distancia entre a seccdo fixa e movel altera-se. Existem avisos para manter as mos e os pés afastados da zona de perigo movel, contudo caso o operador se aperceba de alguma pessoa em perigo, devera avisar a mesma em conformidade.

Os avisos de perigo devem ser sempre mantidos em boas condigdes de leitura de forma a permitir uma leitura clara por parte do utilizador, caso se encontrem danificados deverao ser substituidos

Caso esta maquina manifeste algum erro ou problema durante o seu funcionamento, devera ser imediatamente parada até que o problema em questao seja rectificado.

A montagem, assisténcia e afinagdes ou manutengao de rotina desta maquina, deverao ser somente executadas por tecnicos ou pessoas devidamente qualificadas para o efeito.

Afim de garantir uma protegdo anti - fogo permanente nesta maquina, certifique-se que os fusiveis de prote¢ao sdo sempre substituidos por fusiveis de igual valor ou calibre aos de origem. O uso de outro tipo de fusiveis ou material é proibido. Esta maquina deve estar sempre equipada com uma ficha com circuito de protecgao a Terra, afim de evitar possiveis choques electricos, caso surga uma falha no sistema.

Se a qualquer altura o cabo de alimentagao principal ficar danificado, devera ser imediatamente substituido.

Nao ligar a maquina sem que esta tenha sido correctamente instalada.

Antes de ligar a maquina a tomada da rede de alimentagdo principal, certifique-se de que a maquina esta preparada para a voltagem correspondente e de que também se encontra protegida com os fusiveis apropriados. OPP PB BEB B&

Page 21

(— >) Maintenance zone

NOTAS SOBRE A INSTALACAO

NUNCA ligar a maquina sem que a instalacdo esteja completamente

finalizada. Unit 4

Afim de evitar possiveis choques electricos, certifique-se que a

maquina esta ligada a rede de alimentacao com uma ficha protegida ZA

com circuito de terra. oem!

Afim de evitar danos na maquina causados por falhas de operacao, Oo -F - = certifique-se que a voltagem da rede de alimentacao principal é de ° 230volt AC.

oe ie NOTAS : Se esta maquina estiver colocada sobre um chao polido, recomenda-se Sense ee a utilizagdo de tapetes de borracha debaixo dos pés niveladores, afim [ex eae XS SOK

de prevenir a maquina de deslizar no chao. ea econ

icreieteen nteetclee NOTAS: Quando precisar de aceder & fonte de alimentagao e 4s placas (CPU), < SSP ON oe certifique-se que a parte trazeira do mével central esta separada da parede ou de outras maquinas pelo menos 500mm afim de ganhar Le espaco de manobra. _ laying zone

A\ _ Esta maquina esta equipada com rodas afim de facilitar a sua deslocagao tenha cuidado ao mover a maquina num plano inclinado. A\ _ Aaltura total do bloco principal, é de 1860mm, tenha cuidado com qualquer tipo de obstrugdes

SUBSTITUICAO E MONTAGEM DE PECGAS

A montagem, assisténcia e afinagdes ou manutengao de rotina desta maquina, deverao ser somente executadas por tecnicos ou pessoas devidamente qualificadas para o efeito.

Nao faca qualquer tipo de alteracao prévia nesta maquina sem aprovagao prévia. Se tal acontecer poderé provocar danos e perigos imprevisiveis.

A substituigéo ou reparacao de pegas devera ser feita apenas com pegas de origem ou especificadas pela “Namco Europa Ltd.” (incluindo parafusos)

Certifique-se que a maquina se encontra desligada sempre que iniciar qualquer tipo de trabalho de manutengao. (identifagao de avarias, reparacao etc.)

Caso esteja a efectuar um trabalho nao descrito neste manual, certifique-se que contacta o seu distribuidor para obter instrugdes, caso contrario nao serao aceites responsabilidades por danos causados ou ferimentos. Certifique-se que a maquina esta desligada antes de ligar ou desligar qualquer tipo de fichas ou jungées

Quando desligar a ficha principal da maquina ou a ficha do cabo de alimentago das tomadas da parede, devera sempre agarrar na ficha e nunca puxar pelo cabo da mesma. bP BBB PB &

Page 22

Ge)

Tasta julkaisusta ei saa ottaa missdan muodossa kopioita yksityis- tai julkiseen kaytt66n ilman NAMCO EUROPE LIMITED:in lupaa.

Tassa ohjekirjassa olevat tiedot pitavat julkaisuhetkella paikkansa. NAMCO EUROPE LIMITED:illa on kuitenkin oikeus muutoksiin ilman erillista ilmoitusta.

Tama laite on valmistettu EC direktiivien mukaisesti. Se on testattu ja todettu noudattavan seuraavia direktiivej&: 89/336/EEC ja 72/23/EEC (EN55014, EN55104 ja EN 60335-1 standardit). Nain ollen tama laite on varustettu CE-merkinnailla. Kaikki tahan laitteeseen kohdistetut muutokset on tehtava EC- direktiivien mukaisesti. Mika tahansa valtuuttamattoman huoltomiehen tekema muutos voi olla direktiivien vastainen

Laitteen toiminta voi hairiintya maaratyissa olosuhteissa, jotka johtuvat 4arimmaisista ulkoisista sahkéhairidista, kuten radiolahetys, elektrostaattinen purkaus tai vahvavirrasta syntynyt hairid. Toiminta normalisoituu kuitenkin heti, kun ulkoinen sAhkéhairid on poistettu.

Huom:- Jos peliprosessori resetoituu sahkékatkoksen tai vastaavan johdosta, voivat kaikki pelivaraukset havitd.

Tama laite ei ole 89/392/EEC direktiivien mukainen kone.

Turvallisuusvaroitus

Taman laitteen turvallinen kaytt6 edellyttaa kayttéohjekirjan huolellista lukemista ennen laitteen asennusta, saatda tai kayttda.

Jos taman laitteen omistaja antaa jollekin toiselle osapuolelle tehtavaksi purkaa, asentaa, sAatad tai muuten huoltaa laitetta, on omistajan varmistuttava siita, ett toinen osapuoli on lukenut ja ymmértanyt kayttéohjekirjan oleelliset osat ennen tyohén ryhtymista.

Turvallisuusohjeita on seurattava tarkoin vahinkojen valttamiseksi laitteen ollessa kaytéssa .

Tama ohje seka mahdollinen asennusohje muodostavat laitteiston oleellisen osan ja on siksi aina oltava huolto- ja kayttéhenkildkunnan kaytettavissa.

Tama laite on tarkoitettu vain sisatilakaytt66n. Sita ei saa kayttaa muihin tarkoituksiin.

Namco Ltd ei vastaa niist& onnettomuuksista, loukaantumisista tai vahingoista, jotka johtuvat laitteeseen ilman Namco Ltd:n lupaa tehdyisté muutoksista laitteen vaarasta kaytésta.

Turvallisuusohjeet

Tass kayttéohjekirjassa on kaytetty seuraavia turvallisuuteen liittyvié huomautuksia. Tutustu jokaiseen naista. Ala asenna, huolla tai s4&da laitteistoa, ennen kuin olet taysin ymmartanyt mit ne tarkoittavat

VAARA “Vara” tarkoittaa uhkaa, joka voi johtaa loukkantumiseen tai kuolemaan, Ala koskaan ohita Vaara-merkintaa, ennenkuin ohjeissa esitetyt olosuhteet on ymméarretty taysin.

VAROITUS (1) “Varoitus” tarkoittaa uhkaa, joka voi johtaa laitteen vioittumiseen. Ala koskaan ohita Vaara-merkin ennenkuin ohjeissa esitetyt olosuhteet on ymmarretty taysin.

YLEISET TURVALLISUUSNAKOKOHDAT

Varmista, etd laite on asennettu oikein ja ohjekirjan mukaisesti ennen kayttddnottoa.

Laite sisaltaa toimiessaan liikkuvia osia. On paikkoja, jossa liikkuvien osien ja paikalla pysyvien osien valimatka muuttuu. Tallaisissa paikoissa on varoitustaulut, joissa kehotetaan pitamaan kasia ja jalkoja poissa likkuvista osista. Jos kayttaja on sit mielta, etta joku henkild on vaarassa, on kayttajan velvollisuus varoittaa vaarassa olijaa. >be

Varoitustaulut on pidettava hyvassa kunnossa. Jos ne ovat kuluneet, ne on ehdottomasti vaihdettava, jotta asiakkaalla olisi mahdollisuus lukea niita selvasti.

Jos laitteeseen tulee vika tai ongelmia, on se pysaytettava valittémasti ja ongelma selvitettava ennen uutta kayttddnottoa.

Vain riittavan ammattipatevyyden omaava henkilé saa suorittaa asennus-, huolto-, saat6- tai muita laitteeseen kohdistuvia rutiinitoimenpiteita.

Jotta palovaaraa ei syntyisi, saa padsulakkeita vaihtaa vain samankokoisiin sulakkeisiin. Muiden sulakkeiden tai materiaalin kaytté on ehdottomasti kielletty. Sahkéiskujen valttamiseksi vikatapauksissa, laite on ehdottomasti kytkettava maadoitetulla johdolla maadoitettuun pistorasiaan.

Vioittunut verkkojohto on valittémasti vaihdettava.

Ala kytke laitetta paalle, ennen kuin se on oikein asennettu.

Varmista ennen verkkoon kytkemist, etta virtalahteen jannitteen asetus on asetettu oikealle jannitteelle ja etta siina on oikeat sulakkeet. OPP BP BB &

Page 23

A

©

Huomio: Jos tama laite sijoitetaan liukkaalle esit

Huomio: Varmista, etta takaosan taakse j4& vahintéan 500 mm tilaa, jotta Maintenance zone ASENNUSHUOMIOITA

Ala koskaan kytke laitetta paalle ennen kuin asennus on suoritettu loppuun.

Taman laitteen virtalahde on kytkettava maadoitetulla johdolla maadoitettuun pistorasiaan, jotta sahkdiskun vaaraa ei olisi.

Varmista, etta virtalahteen jannite on 230 V AC, jotta ei laite vioitu.

vahatulle lattialle, suositellaan laitettavaksi kumityynyt sAatdjalkoihin liikkumisen estamiseksi.

virtalahteeseen ja CPU-korttiin padsee kasiksi.

Playing zone

A Laite on varustettu kaantyvilla pydrilla. Tama on pidettava mielessd, kun laitetta siirretaan kaltevalla alustalla.

Laitteen kokonaiskorkeus on yli 1860 mm. Varmista, ettei katossa ole esteita. esim. valaisimia.

PBPBBE BP BP B& OSIEN JA OSAKOKONAISUUKSIEN POISTO JA VAIHTO

Vain riittavan ammattipatevyyden omaava henkilé saa suorittaa asennus-, huolto-, saaté- tai muita laitteeseen kohdistuvia rutiinitoimenpiteita.

Talle laitteelle ei saa tehda mitéan hyvaksymattomia muutoksia. Se voi aiheuttaa ennalta-arvaamattomia vaaroja.

Vain Namco Europe Ltd:n maarittelemia varaosia saa kayttaa vaihtaessasi tai korjatessasi osia. (sisaltéen ruuvit).

Varmista, etta laite on kytketty POIS PAALTA ennen tyén aloittamista.

Ota yhteytta maahantuojaan ohjeita varten, jos joudut tekemaan tydtehtavid, joita ei ole esitelty huoltokirjassa, muuten vastuuta vioista tai loukkaantumisista ei ole. Varmista, etta laite on kytketty POIS PAALTA ennen johtojen kytkemista tai irrottamista.

Irrottaessasi verkkojohdon seinasta tai laitteesta, ota kiinni itse pistokkeesta, ei johdosta.

Page 24

Contents

OPERATORS MANUAL. PORTABLE APPLIANCE TESTING GENERAL SAFETY CONSIDERATIONS. ALLGEMEINE SICHERHEITSHINWEISE ... CONSIDERACIONES GENERALES DE SEGURIDAD. . CONSIGNES GENERALES MDE SECURITE

CONSIDERAZIONI GENERALI SUL! VANLIGESIKKERHETSTILTAK ........cececeeee ALGEMENE VEILIGHEIDSOVERWEGINGEN .. AVISOS DE PERIGO YLEISET TURVALLISUUNAKOKOHDAT. SPECIFICATIONS HOW TO PLAY MAJOR COMPONENTS .. MOVING THE MACHINE . INSTALLATION ... 5-1 Adjusting the Level 5-2 Fitting the Ball

  • ADJUSTMENTS... 6-1 Turning on the Powe: 6-2 Adjustment Switches 6-3 Test Mode.. 6-4 Set Mode.... 6-5 Error Displays
  • MAINTENANCE AND ADJUSTMENTS... 7-1 Troubleshooting ... 7-1-1 Rail Assy... 7-1-2 Seesaw Assy 7-2 Adjusting the AC Solenoid.. 7-3 Replacing the Solenoid and Fluorescent Lamp Fuse.. 7-4 Replacing the Hammer ... 7-5 Replacing the Wire Rope 7-6 Replacing the Ball ........... 7-7 Replacing the Fluorescent Lamp .. 7-8 Replacing the Display Lamps 7-9 Replacing the Sensors.... 7-10 Replacing the AC Solenoid. 7-11 Replacing the Score PC Board . 7-12 Replacing the Rail Cushion 7-13 Seesaw Assy . 7-13-1 Replacing the Target . 7-13-2 Removing the Seesaw Assy. 7-13-3 Replacing the Main shaft...... 7-13-4 Replacing the Sub Shaft and Sub Shaft Rubber. 7-13-5 Replacing the Seesaw Spring.
  • PARTS........
  • SCHEMATIC... OQ PoONs
Page 25
  • SPECIFICATIONS

POWER SUPPLY:- 230volts AC

AMBIENT OPERATING ° ° +5°C to +25°C TEMPERATURE:-

COIN ACCEPTOR:- Mars CashFlow - 1 Channel

DIMENSIONS:- 660(w) x 780(d) x 1860(h)

WEIGHT:- 135kg.

ACCESSORIES:- Keys: (Cash Door).......cccccee (Coin Door) (Ticket Door) (Back Door)....

IEC Mains Lead ........ccceeeneeeee 1

Operators Manual ..........:ccecee 1

CashFlow Document ..........0006 1

Page 26
  • HOW TO PLAY

Spin-the-Spin is a one-person action ticket dispense game that can be enjoyed by players of all ages, from young children to adults.

Once the player inserts the correct value of coins, the ball will be released to the start position. As soon as the ball has been set in place the target display will show a random number. The player hits the target pad with the mallet to try and spin the ball around the track to match the number shown in the target display. The closer to the target number the more tickets are won. If the number of spins matches the target display number the player will win the number of tickets shown on the jackpot display.

Page 27
  • MAJOR COMPONENTS

Jackpot Display Ticket Win Display cront Aervii ron crylic

Score Display

Target Display Rail Assy Ball

Hammer Target

Front Cushion

Coin Door

Cash Door

Seesaw Assy & Cashbox Sub shaft side)

Seesaw Assy (Main shaft side)

Wire Rope

Ticket Door

Maintenance Door —— ||

AC Solenoid

Main PC Board

PSU Board & Fuses

ON/OFF Switch & Mains-in Fuses

Mains-In Socket

Page 28
  • MOVING THE MACHINE

5. This machine is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface.

Z\ The overall height of the machine is 1860mm. Take care of any overhead obstructions. (e.g. Light Fittings, Electric Cables etc.)

INSTALLATION

Notes on Installation

ENSURE THAT THE MACHINE IS LEVEL AND STABLE BY RAISING AND ADJUSTING THE LEVEL ADJUSTERS. (See Section 5-1 Page 32)

FAILURE TO COMPLY MAY CAUSE THE BALL TO NOT SPIN CORRECTLY OR THE TILT SWITCH TO MALFUNCTION.

ZA WARNING

A\

LN

® CAUTION

NEVER turn the power to the machine ON until installation has been completed.

In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a securely connected earthed plug.

So that customers are not injured , ensure that there is at least 500mm separation between other machines or walls and 1700mm clearance in front of the machine.

In order to avoid damage to the machine due to misoperation, ensure that the voltage of the mains supply is 230volts AC.

NOTE

If the location site of this machine has a polished floor it is

recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor.

In order to gain access to the Power Supply and CPU assemblies, make sure that the rear of the machine is separated from a wall or other machine by at least 500mm.

Page 29

Maintenance zone

Unit

SS] SI J ee “ ne <x S ret SS x es or, ~ x] 3m XS SY XS ss SQ SS SS xX SS wet SVN x net SY Se SONS ef . Ox ence SQ SR RRLO XS xR Ro BS <x SS “% ey “s oS SR see ons ae se mace SSOXD BRR Oe ES Roe. K> COS KS S Ss be cS XA

Playing zone

A

This machine is designed for INDOOR USE ONLY. Do not install in the following places. Outdoors Direct Sunlight, places with excessive humidity or dust, places where there is water leakage, near air-conditioning or heating equipment, places with excessive heat or cold temperature. Places where it would be in the way of emergency exits or fire extinguishing equipment. Unstable places or places with excessive vibration. Places that are not level. as

Page 30

©)

RO

aw A

DIESES GERAT IST NUR FUR DIE GEWERBLICHE AUFSTELLUNG IN GESCHLOSSENEN RAUMEN BESTIMMT. DAS GERAT DARF AN FOLGENDEN PLATZEN NICHT AUFGESTELLT WERDEN

Im Freien. In direktem Sonnenschein, an extrem feuchten und staubigen Platzen, an Platzen mit Wasseranschllssen und méglichen Leckagen, nahe Klima- und Heizungsanlagen, an Platzen mit extrem hohen oder niedrigen Temperaturen. In der Nahe von Notausgangen oder Feuerléschgeraten. An unstabilen Platzen oder Platzen mit UbermaBiger Vibration. An Platzen, die nicht eben sind.

ESTA MAQUINA ESTA DISENADA UNICAMENTE PARA USO EN INTERIORES. NO INSTALE LA MAQUINA EN LOS SIGUIENTES LUGARES.

Exteriores. Bajo luz solar directa, en lugares con polvo o humedad excesiva, lugares donde hay filtraciones de agua, cerca de aparatos de calefaccién o de aire acondicionado, lugares con temperatura ambiente muy alta o muy baja. Lugares donde la maquina obstruya salidas de emergencia o equipos de extincion de incendios. Suelos inestables o lugares con vibraciones excesivas. Lugares con suelos no nivelados.

CETTE MACHINE EST DESTINEE UNIQUEMENT A UN USAGE INTERIEUR NE PAS INSTALLER LA MACHINE DANS LES ENDROITS SUIVANTS

Al’extérieur. Directement exposée au soleil, aux endroits excessivement humides ou poussiéreux, aux endroits ou il y ades risques de fuite d’eau, prés de ventilateurs ou source de chaleur, aux endroits trés chauds ou froids. Dans des zones de proximité des sorties de secours ou d’accés aux équipements d’extinction du feu. Dans des emplacements instables ou soumis a de fortes vibrations. Dans des endroits dénivelés.

TO MHXANHMA EINAI ZXEAIAZMENO IIA XPHZH LE ELQTEPIKO XQPO MONO MHN TOMOOETHZETE TO MHXANHMA LTOYE AKOAOYOOYE XQPOYE

Efortepixa Anev0eiac otov 210,68 pépy Oz0v vadpyer vypacia } oKévy,pépy 6z0v vTaPYEl GQOOVO vep6,KovTa o¢ air-condition } G20 idous Oéppavon,pépy pe vtepPokiKy vyyAH H Yann OeppoKxpacia. Le pépy 6z0v eprodiCovv péca avayKys 7.x. TvpooPeotipesc f GAG. My otabepa pépy h pépy pe 70Ad00¢ Kpadacpotc. Mépy ov dev sivan exineda.

Page 31

‘O)

as

as QUESTA MACCHINA E’ PROGETTATA PER ESSERE USATA ESCLUSIVAMENTE IN AMBIENTI INTERNI. NON INSTALLARE LA MACCHINA NEI SEGUENTI LUOGHI.

In ambienti esterni. Alla luce diretta del sole, in posti con eccesiva umidita 0 polvere, in luoghi dove ci siano infiltrazioni d’acqua, vicino ad apparecchi di condizionamento d’aria oppure riscaldamento, in posti eccessivamente caldi o freddi. In luoghi dove potrebbe esserci un uscita di emergenza 0 un’attrezzatura per lo spegnimento del fuoco. In posti non stabili o con eccessive vibrazioni. In luoghi non piani.

DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDORS BRUK IKKE INSTALLER MASKINEN PA FOLGENDE PLASSER.

Utendors Konstant sollys, plasser med mye fuktighet og stov, plasser hvor det er vannlekasje, neere luft kjolere eller varme elementer, plasser med overdreven hoy eller lav temperatur. Plasser hvor det vill sta i veien for nodutganger eller brannslukking utstyr. Ustabile plasser eller plasser med overdreven vibrasjon. Plasser som ikke er i vater.

DEZE MACHINE IS ALLEEN VOOR GEBRUIK BINNENSHUIS ONTWORPEN INSTALLEER DE MACHINE NIET OP DE VOLGENDE PLAATSEN

Buiten In direct zonlicht, op plaatsen met een zeer hoge vochtigheidsgraad of met veel stof, op plaatsen waar een waterlek is, dichtbij airco’s of verwarmingsapparatuur, op plaatsen met een zeer hoge of koude temperatuur. Op plaatsen waar nooduitgangen of blusapparatuur worden geblokkeerd. Op onstabiele plaatsen of plaatsen waar grote trillingen voorkomen. Op plaatsen die niet viak zijn.

ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAGAO EM ESPACOS INTERIORES APENAS NAO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:- Exteriores. “Luz solar directa, locais com humidade excessiva ou pd, locais aonde existam fugas de agua perto de ar condicionados ou equipamentos calorificos e locais com temperaturas excessivamente quentes ou frias. Locais aonde ficaria colocada no caminho de saidas de emergéncia ou equipamentos extintores de fogo. Locais estruturalmente instaveis ou locais com vibrag6es excessivas. Locais nao nivelados.

TAMA LAITE ON SUUNNITELTU VAIN SISAKAYTTOON ALA ASENNA LAITETTA SEURAAVIIN PAIKKOIHIN:

Ulkotilaan Suoraan aurinkovaloon, kosteisiin tai pdlyisiin paikkoihin, vesivuotopaikkojen laheisyyteen, ilmanvaihto- tai lammityslaitteen lahistdlle tai paikkoihin, jossa on erittain kuumaa tai kylmaa. Varauloskaytavien, muiden pakoteiden tai tulensammutusvalineiden eteen. Epavakaisiin tai tariseviin paikkoihin. Kaltevalle alustalle.

Page 32

5-1 Adjusting the Level Adjusters

When the machine is in it’s final position, lower the four level adjusters, with a spanner, so that the castors are raised from the floor by approximately 5mm _and the machine is level. Tighten the lock nuts with a spanner to ensure that the level adjusters do not move.

If the machine is installed on a smooth or shiny floor, it is recommended that rubber pads are fitted under each adjuster to prevent the machine from moving when being p!

Castor

mes) Level Adjuster

ayed.

Fitting the Ball

  • Remove the 2 security screws (M4x12), spring and flat washers and remove the window retainers (B) from the front window.
  • Remove the 3 security screws (M5x12) and remove the top retaining bracket.
  • Remove the front window.
  • Remove the rail holder, only fitted for shipping, and store it in a safe place for re-use if the machine is moved at a future date.
  • Fit the ball in the location shown in the drawing opposite.
  • Re-assemble the window and brackets in reverse order to above.
Page 33

Security Screw (M5x12) Security Screw (M4x12)

Page 34
  • ADJUSTMENTS

@

CCM CC AC MOMEC) uN Adjustment or maintenance on this machine should be carried out by qualified personnel only. Aufstellung, Service, Einstellung und Wartung d-rfen nur von dafer qualifiziertem Fachpersonal durchgef-hrt werden. Los ajustes y el mantenimiento de esta maquina deben ser realizados sOlo por personal cualificado. L’installation, le service, le réglage, ou la maintenance doivent étre effectués uniquement par les personnes qualifiées. Metatponés i extdr0p0doeis ota pHyYavipata mpérEl va yivovtat pdvo and efovoiodsotypéva atone. Regolazioni e manutenzione su questa macchina devono essere fatti solo da personale specializzato. Justering eller vedlikehold pa denne maskinen skall bare utfores av kvalifiserte personell. Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te worden door bekwaam personeel. Afinagédes ou manutengao nesta maquina, deverdao ser efectuadas sOmente por pessoal qualificado. Taa laitetta saa saataa tai huoltaa vain siihen ammattipatevyyden omaava henkilékunta.

6-1 Turning on the Power

After the machine has been installed, turn ON the power. The power switch is located on the rear of the cabinet.

6-2 Adjustment Switches

The Adjustment switches are located inside the coin door.

1. Service Switch. Press this switch to obtain game credits without incriminating the play meter.

Test Switch Slide the test switch ON to enter test mode. Test mode allows testing and the changing of game settings. (Refer to section 6-3 "Test Mode" (page 35))

Select Switch Used to step through tests and COIN COUNTER game settings. ° (2) COIN 2A G/B Volume Control = Used to set the speaker volume level. O O TICKET 1.6A Q/B

TEST SERVICE SELECT © )

Page 35

6-3 Test Mode

The Test Mode allows the LED Displays, Lamps, Sensors, Switches and Solenoid to be checked. To enter the test mode open the coin door and slide the test switch ON. To advance to the next test routine press the select button. The test number will be displayed in the score display. Slide the test switch OFF to return to normal game mode. The test switch must always be in the “OFF” position for normal game mode.

Item Dispaly

Top Bottom Row Row Contents

Lamp Test Each digit displays 0-9 in order repeatedly Lamps are illuminated one at a time in the following order: Spin lamp (starting at the top and moving clockwise)>Standby lamp>Shot lamp Input Test all sensors and switches can be checked. When the ball is placed next to the sensor, or a switch turned ON, the corresponding lamp will illuminate and a sound will be produced. Upper ball sensor (PS1) : Top spin lamp Lower ball sensor (PS2) : Second spin lamp

Standby sensor (PS3) _: Third spin lamp

Coin signal : Sixth spin lamp

Tilt switch : Eighth spin lamp

AC Solenoid Test When the service switch is pressed, the AC solenoid will energise. In this condition the solenoid’s position can be adjusted. Pressing the service switch again will de-energise the solenoid. (see 7-2 "Adjusting the AC Solenoid" - page 17)

Sound Test During this test all the sounds will be produced in sequence and the volume level can be adjusted.

Page 36

6-4 Set Mode

The price of play, ticket wins and other settings can be made in Set Mode. To enter the Set Mode, open the coin door, press and hold the Select Button and slide the test switch ON. The item number and contents are displayed in the Score and Target displays. To advance to the next item press the select button. The contents can be changed by pressing the service button. To store the new values advance to the next step, or slide the test switch OFF to return to normal game mode. The test switch must always be in the “OFF” position for normal game mode.

NOTE: The price of play on this game is set within the Cashflow Coin Mech. Ensure that the Coin/Game options (1 & 2) are both set to 1.

Display Contents

ItemTop|Bottom Row(Changed by the service switch)Factory Set
p9yy

Row

Number of Coins11-3‘Sets the number of coins for 1 credit.1

1 (1 coin) ~ 3 (3 coins)

Number of Games | 91-3Sets the number of games for 1 credit.1

1 (1 game) ~ 3 (3 games)

Number of Hits31~3Sets the number of attempts for 1 game.1

1 (1 try) ~ 3 (3 tries)

Minimum Target45~10Sets the low limit for the Target Display.8

Number

Maximum Target10~Sets the maximum for the Target Display.
Number50~30DO NOT SET ABOVE 2020

out -5 -4 -3 -2 -1 Match

1 (S-Low)13 45 6 10 Jackpot
2 (Low)1.3 45 7 15 Jackpot
Ticket Payout61~6|3(V-Low13 46 10 15 Jackpot4
4(Normal) 1468 10 15 Jackpot
5 (High)1468 1220 Jackpot
6 (S-High)146 10 15 20 Jackpot
Minimum Jackpot710~100 Minimum level that the jackpot is reset to.30

Number

Jackpot Increment) g 110 Number that the jackpot is incremented by 5

for each non-jackpot winning game.

Maximum Jackpot~~,Maximum level that the jackpot can reach.
Number90~300if set to 0, jackpot will always be at 999300
Sound in Attract1~0 : Attract Sound OFF
001: Attract Sound ON1
Tilt Switch11Om0 : Tilt Switch OFF1

: Tilt Switch ON

Page 37

6-5 Error Displays

When an error occurs, the game can no longer be played. A vocal warning is repeated, and an error code displayed in the score display.

Display Score | Target Problem Possible Cause display | display 01 Ball standby error Flashing This error message will be displayed if the standby sensor is not turned ON within 3 seconds of the adjuster rail operating

The ball is stuck on the adjuster rail Check the rail and/or the AC solenoid.

The ball is in the standby position Check the standby sensor. 02 Tilt error

Flashing An alarm will sound and the display flash

for 20 seconds, then just the display will flash for a further 60 seconds.

The machine has been hit or shaken Normal

Tilt error occurs during normal play Check that the tilt switch is secure. If error continues, set tilt switch to the OFF condition (see section 6-4 Set Mode) 03 Spin Error

for 20 seconds, then just the display will flash for a further 60 seconds.

Ball does not spin properly due to Normal tampering.

Upper and lower sensors Check the upper and lower malfunctioning. sensors.

Page 38
  • MAINTENANCE AND ADJUSTMENTS

In order to prevent injury or electric shock, ensure that the MAIN POWER is OFF before attempting any maintenance.

Before performing any work not described in this manual, be sure to contact your distributor to receive instructions or answers to questions.

Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muB der Netzstecker gezogen werden.

Bei Arbeiten, die nicht in diesem Handbuch beschrieben werden, muB vorher der Handler zu Rate gezogen werden, da sonst keinerlei Haftung bei Beschadigungen und Verletzungen Ubernommen wird.

Asegurese de que la maquina esta desconectada antes de comenzar cualquier trabajo de mantenimiento (reparaciones, resolucion de problemas, etc.)

Al realizar trabajos no descritos en este manual, pOngase en contacto con su distribuidor para recibir instrucciones. Se declina cualquier responsabilidad por dafios o lesiones.

S’assurer que |’interrupteur soit sor OFF avant de commencer tout travail de maintenance (localisation d’une panne, réparations, etc.)

Si dans ce manuel il manque une information pour réaliser un quelconque travail, contacter votre distributeur, car aucune responsabilité ne sera acceptée en cas de domage ou de blessure.

Na sivai ciyoupa KAgioté To peda mpl onoladyzotE SovAElé oTO pHYGvHpG.

Eav yivei Kazo1g SoviAE14 oto pHyavypa yopic va Sievkpiwiletar oto eyzerpisio , VO ETIKOLWOVIGELS HE TOV GVTITPOGO70 yia OdHyiEs yLaTi Kapia evddvy dev MEpOvpE Yla KaTaGTPOEs H PAGBEc.

Assicurarsi che la macchina sia SPENTA prima di incominciare qualsiasi lavoro di manutenzione (guasti, riparazioni etc.)

Se state per iniziare un lavoro non descritto in questo manuale, contattate il vostro distributore per instruzioni poiché non si accetta alcuna responsabilita per danni 0 ferite.

Page 39

Forsikre deg om at strommen er slatt av for du pabegynner noe som helst vedlikeholdsarbeid (feilsoking, reparasjon osv.)

Hvis du utforer arbeid som ikke er beskrevet i denne manualen, ta kontakt med din distributor for instruksjon da ikke noe ansvar vill bli akseptert for skade pa maskin eller pa personer.

Zorg ervoor dat de machine UlTgeschakeld is voordat er enig onderhoudswerk wordt verricht (troubleshooting, reparaties etc.)

Bij het verrichten van werkzaamheden die niet in deze handleiding staan beschreven, dient voor instructies altijd contact opgenomen te worden met de verdeler aangezien geen verantwoording wordt genomen voor schade of letsel.

Certifique-se que a maquina se encontra desligada sempre que iniciar qualquer tipo de trabalho de manutencao. (identifagao de avarias, reparacao etc.)

Caso esteja a efectuar um trabalho nao descrito neste manual, certifiquese que contacta o seu distribuidor para obter instrucées, caso contrario nao serao aceites responsabilidades por danos causados ou ferimentos.

Varmista, etta laite on kytketty POIS PAALTA ennen ty6n aloittamista.

Ota yhteytta maahantuojaan ohjeita varten, jos joudut tekemaan tyétehtavia, joita ei ole esitelty huoltokirjassa, muuten vastuuta vioista tai loukkaantumisista ei ole.

Page 40

7-1 Troubleshooting

7-1-1 Rail Assy

Symptom Main cause Solution Ref Page

Number of spins of|The ball is damaged.Replace the ball.20

ball decreases. P.

Adjuster rail shakes.Replace rail cushion if26

worn. Pp. If not above, adjust AC 17 solenoid. Pp.

Adjuster rail doesThe 250v 1A fuse on the |Replace fuse and conduct18
not move.PSU board is blowna rail test.P.
AC solenoid connector{Reconnect the connector.23

loose. P.

Balancer screw out of|Retighten the screw.1

place. p17

Damaged spring.Replace the spring.p.17
AC solenoid notReplace the solenoid.23

working. p:

Adjuster rail doesLower ball sensor’sReconnect the connector.20

not connect with the |connector is loose. P. main rail after the Lower ball sensor is not |Replace the sensor. target is hit. if p. 22 working.

Fluorescent lampFluorescent lamp isEnsure lamp is fully
does not illuminate.|loose.screwed into the lampp.21

holder.

Fluorescent lamp isReplace the fluorescent24
burnt outlampP.
Display lamp doesLoose connectorReconnect the connector

not illuminate. p.24

Lamp is burnt out.Replace the lamp.p.2t
LED display doesDisplay board connector |Reconnect the connector.2
not illuminate.is loose.p. 25
Display board is faulty.|Replace the display board.p. 25

7-1-2 Seesaw Assy

Target is stuck inSeesaw spring isReplace the spring30
lowered positiondamaged.P.

Rubber on the bottom of |Replace the main shaft. the main shaft is p. 28 damaged.

Page 41

7-2 Adjusting the AC Solenoid

1. ‘Spring Bracket Loosen the 3 socket cap screws (M4x12) holding the spring bracket in place. (Only loosen the screws sufficiently so that the screw heads are in contact with the bracket, but the bracket can move up and down.) Adjust the spring tension so that the adjuster rail drops fully. Retighten the 3 socket cap screws (M4x12). ssp Sore

Loosen the locking nut (M6) and slacken the pozi head screw (M6x40) used for adjusting solenoid bracket (A).

Loosen the 4 socket cap screws (M5x12) holding solenoid bracket (A) in place. (Only loosen the screws sufficiently so that the screw heads are in contact with the bracket, but the bracket can move up and down.)

Solenoid bracket (A) Solenoid bracket (B)

«>

© ' AC solenoid ‘ozi Head Screw (M6x40) Locking Nut (Mé) Socket Cap Screw (M5x12)

Turn the power to the machine ON.

Select the rail test in Test Mode (see section 6-3) and press the service switch once, activating the AC solenoid. (Adjuster rail connects with the main rail.)

Adjust the solenoid bracket (A) up and down with the pozi head screw (M6x40) so that the adjuster rail and main rail are in solid contact but without any buzzing from the solenoid. Re-tighten the 4 socket cap screws (M5x12) that hold solenoid bracket (A) in place.

Press the service button twice, reactivating the AC solenoid, and confirm that there is no change in the contact condition of the adjuster rail and main rail and the solenoid does not buzz. Tighten the locking nut (M6) making sure that the adjustment screw does not move. Release and energise the solenoid 2 - 3 times. If a change does occur, repeat from step 6 and readjust the solenoid bracket (A).

Slide the test switch OFF to return to game mode.

Page 42

7-3 Replacing the Solenoid and Fluorescent Lamp Fuse

The fuse holder is of the type where the end caps of the fuse are inserted between clasps. To remove the fuse, gently prise out using a small screwdriver or similar tool. To install a fuse, place the fuse end caps on the clasps and press both ends of the fuse into the clasps with equal force. (Use a 1%” 250v 1A Q/B fuse)

a Fuse 250v 1A QB.

7-4 Replacing the Hammer

  • Remove the security screw (M4x25) and 2 flat washers (M4) from the end of the grip.
  • Ensure that the ring of the rope is between the 2 flat washers and fit to the end of the grip with the security screw (M5x25).
  • Pull on the wire rope to ensure that it is fastened securely.

a, Screw (M5x25) Flat Washer (M5) <

“Fy Wire rope

J EC

Hammer

Page 43

7-5 Replacing the Wire Rope

  • Remove the 2 security screws (M5x20) and 4 security screws (M5x35) (complete with flat and spring washers), holding the front table in place, and remove the front table.
  • Remove the 2 Hex head screws (M5x14) retaining the old wire rope in place on the rear of the front table, and install the new wire rope between the front cushion and the front cover.
  • Refit the front table with the 2 security screws (M5x20) and 4 security screws (M5x35) complete with the flat and spring washers.

Ensure that there is a uniform gap between the target and bezel.

Security screw (M5x35), Flat & Spring washer Hammer holding ring Front table

Security screw (M5x20), Flat & Spring washer

wn "eTOPe Hex Head Screw (M5x14) (with Flat & Spring washer) Wire rope \ Front table

Front cover

Front cover

Page 44

7-6 Replacing the Ball

1. Remove the 2 security screws (M4x12) flat and spring washers, and window retainers (B).

Remove 3 button head screws (M5x12) and remove the top retaining bracket.

Remove the front window.

Replace the ball and position it as shown in the diagram.

Assemble in reverse order.

ZZ

Page 45

7-7 Replacing the Fluorescent Lamp

  • Remove the front window (see section 7-6 “Replacing the Ball”)
  • Remove the fluorescent lamp by unscrewing it anti clockwise from the lamp holder.
  • Replace the fluorescent lamp. (230v 11watt)
  • Reassemble in reverse order.
Note: When replacing the fluorescent lamp, always use a fluorescent lamp of the same rating. Failure to do so may cause heat damage to the plastics within the vicinity of the fluorescent lamps

Fluorescent Lamp

7-8 Replacing the Display Lamps

  • Remove the back door.
  • Remove the lamp from it’s holder by pushing the lamp in and turning anticlockwise at the same time.
  • Refit the lamp by inserting it into the lamp holder then pushing the lamp in and turning it clockwise at the same time. (Use a 24v 10w Auto lamp)
Page 46

7-9 Replacing the Sensors

  • Remove the front window. (see section 7-6 “Replacing the Ball”)
  • Remove the connector from the sensor.
  • Remove the pozi head screw (M3x16) and spring washer, and remove the sensor.
  • When refitting the sensor, ensure that the grey face of the sensor is facing away from the ball track.
  • Reassemble in reverse order.

[Upper Ball Sensor]

[Lower Ball Sensor]

Pozi Head Screw, with Spring Washer (M3x16)

Pozi Head Screw, with Spring Washer (M3x16)

[Stanby Sensor]

Pozi Head Screw, with Spring Washer (M3x16)

Page 47

7-10 Replacing the AC Solenoid

1.

2.

Spring shaft Remove the back door.

Remove the pozi head screw (M3x8) holding the spring clip in place and remove the spring clip. Remove the spring shaft

Remove the 3 socket cap screws screws (M4x12) that hold the spring bracket in place and remove the spring bracket.

Remove the socket cap screw (M6x20) holding the adjuster rail and balancer in place.

Disconnect the connector.

Remove the 4 Nyloc nuts (M4) holding the solenoid bracket (B) in place, and pull both the bracket (B) and the balancer towards you, keeping them level.

Pozi Head Screw (M3x8) Spring clip Socket cap screw (M6x20) Balancer

Adjuster rail Nyloc nut (M4) Spring bracket

Balancer

Solenoid bracket (B)

Connector

Page 48
  • Pull the snap pin off the plunger’s solenoid shaft, Plunger remove the solenoid shaft, Snap pin and then remove the plunger. Solenoid shaft
  • Slacken the locking nut (M6) and the pozi head screw (M6x40) that hold the solenoid bracket (A) and solenoid bracket (B) in place.
  • Remove the 4 socket cap screws (M5x12) that hold solenoid bracket (A) in place and remove the solenoid bracket (A).

Solenoid bracket (A) Pozi Head Screw (M6x18)

codnal Solenoid bracket (B)

Pozi Head Screw (M3x8) Spring shaft

AC solenoid Posi head screw (M6x40) Locking nut (M6) / Socket cap screw (M5x12) Connector Socket cap screw (M4x12)

  • Remove the 4 socket cap AC solenoid ~ screws (M5x12) holding the AC Solenoid in place and replace the AC solenoid.
  • Reassemble in reverse order.
  • Adjust the AC solenoid. (see section 7-2 “Adjusting the AC Solenoid”) Socket cap screw (M5x12)
Page 49

7-11 Replacing the Score PC Board

  • Remove the front window. (see section 7-6 “Replacing the Ball”.)
  • Remove the 4 pozi head screws (M4x10) that hold the score bracket (A) in place. Remove the score bracket (A) only sufficiently enough to disconnect the connector, Remove the score bracket (A).
  • Remove the 4 pozi head screws (M4x10) that hold the score bracket (B) in place, and remove score bracket (B).
  • Squeeze the locking tags of the locking support with radio pliers or similar tool, and carefully remove the Score PC Board from each locking support one at a time.
  • Reassemble in reverse order.

Score bracket (A) mn \ >

© °

l ay xO 5 i | | Pozi Head Screw (M4x10)

a1" Locking support yy = 2 Radio pliers or similar tool

Pozi Head Screw (M4x10)

Locking support Score PC Board

Page 50

7-12 Replacing the Rail Cushion

  • Remove the front window (see section 7-6 “Replacing the Ball”.)
  • Peel off and replace the rail cushion.
  • Reassemble in reverse order.

Rail cushion

Pozi Head Screw (M4x12), Flat & Spring Washer

)

Adjuster rail

+— Rail cushion

aE

Page 51

7-13 Seesaw Assy

7-13-1 Replacing the Target

Note: Replace the target rubbers — Security Screw (M5x35), Flat & Spring Washer (4 pieces) when replacing Front Table the target.

Remove the 2 security screws (M5x20), 4 security screws (M5x35) and 6ea flat and spring washers holding the front table in place, and remove the front table.

Replace the target and target rubbers.

Reassemble in reverse order.

Target Rubber Target eee?)

7-13-2 Removing the Seesaw Assy

1. Remove the front table assembly (see section 7- 13-1 above) Socket cap screw (M6x25), flat & spring washer

Remove the 4 socket cap screws (M6x25), flat and spring washers holding the seesaw assembly in place, and remove the seesaw assembly.

Reassemble in reverse order. | Seesaw Assy

Page 52

7-13-3 Replacing the Main shaft

  • Remove the Seesaw Assy (see section 7-13-2 “Removing the Seesaw Assy”)
  • Remove the 4 Nyloc nuts (M6) holding the main shaft bracket in place and remove the main shaft bracket.
  • Remove the target and socket cap screw (M6x20), flat and spring washer that holds the main shaft in place and remove the main shaft.
  • Reassemble in reverse order.

Ensure that the target is central in the bezel when reassembling.

Socket cap screw (M6x25), tlat & spring washer

Neck Flange

Main Shaft Bracket

Main Shaft Nyloc nut (M6)

Page 53

7-13-4 Replacing the Sub Shaft and Sub Shaft Rubber.

  • Remove the front glass. (see section 7-6 “Replacing the Ball”)
  • Remove the front table. (see section 7-5 “Replacing the Wire Rope”)
  • Remove the 4 socket cap screws (M5x16), flat and spring washers that hold the sub shaft frame in place, and remove the sub shaft frame.
  • Remove the sub shaft rubber by unscrewing it from the sub shaft.
  • Fit the new sub shaft rubber by screwing it in to the sub shaft.
  • Reassemble in reverse order.

Ensure that the target is central in the bezel when reassembling.

Sub Shaft Rubber Sub Shaft Rubber

Socket cap screw (with Flat and Sring Washer) (M5x16)

Sub Shaft Frame Sub Shaft

Sub Shaft

Page 54

7-13-5 Replacing the Seesaw Spring

  • Remove the seesaw assy. (see section 7-13-2 “Removing the Seesaw Assy”)
  • Remove the pozi head screw (M3x8) and snap pin that hold the spring shaft (A) in place, and pull out the spring shaft (A).
  • Remove the 4 socket cap screws (M6x12) that hold the spring bracket in place, and remove the spring bracket.
  • Remove the pozi head screw (M3x8) and snap pin that hold the spring shaft (B) in place, and pull out the spring shaft (B).
  • Replace the seesaw spring.
  • Reassemble in reverse order.

Spring Shaft (A) . Snap Pin Seesaw Spring

Spring Shaft (B) Pozi Head Screw (M3x8)

Spring Bracket

Socket cap screw (M6x12)

Page 55

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 56

Item Description Part No

1Wooden Cabinet37100134
2Swivel Castor - 75mm59000005
3Adjustable Foot - M1688300079
4Front Cover Bracket46000343
5Cushion Assy37100137
6BezelX658-116
7Speaker Grille46000344
8Hammer Holder Surround46000345
9Hammer Holder46000346
10|Side Decal LHS/RHS40000441
11|Front Acrylic - Version B30000088
12| Ticket Out Decal40000440
13|Front Acrylic Support Bracket46000348

14 | Ticket Dispenser 67000246

15.|Front Acrylic Top Retaining Bracket46000349

16 |Jackpot Display PCB XSP-TicketPCB

17|Hammer Decal40000442

Schaffner Mains-in Filter 62500010

*sSchaffner Boot66000017

30 = |Rear Door 37100138

Interlock Switch 60000006

*Interlock Switch Cover39000028
32|Speaker - 4%e' 20watt62000006
33|Hammer - Version B Red Cover46000816
34|Hammer Rope - Flame Retardent46000731
35|Speaker Panel Decal40000439
Page 57

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 58

Item Description Part No

2Main Rail46000359
3|Adjuster Rail46000360
4{Rail Bracket46000361
5|Limit Bracket46000362
6|Rail Cushion46000363

7 — |Fluorescent Lamp Holder (LH62050) 64000090

8|Heavy Duty Lamp 24v 10w Bayonet64000091
10|Balancer46000366
11|Solenoid Rod46000367
19|Spin Assy Raer Acrylic30000087
20{Sub Rail46000375
21|Solenoid Return Spring46000379
22{Inner Spin Ring39000072
24|Spring Shaft46000377
25|Bearing 80F-060346000380
26|Bearing 80FL-0846000381
27{Fluorescent Lamp 11watt (See Note Below)64000089
28{Lamp HolderX002-105

29 {Score PC Board XSP-SCOREPCB

30{AC Solenoid46000382
31|SensorX000-299
32|Solenoid Mounting Bracket - version B46000732
33|Solenoid Assembly Mounting Bracket - version B46000733
34|Fluorescent Lamp Securing Bracket46000820
35{Ball - Delrin46000827
NOTE: Replace only with lamp specified.
Page 59

a Ly at “

ee” ¥

Page 60

Item Description Part No

1|Hit Cover Actuator Arm Rubber Bumper46000404
2|Hit cover Actuator Arm46000821
3|Seesaw46000385
4|Return Spring Upper Retaining Shaft46000386
5_|Return Spring Upper Retaining Shaft46000387
6|Ball Shooter Actuator Arm Rubber Bumper Lower46000405
7|Hit Cover Actuator Arm Bearing46000389
8|Hit Cover Rubber Bumper46000390
9|Hit Cover InternalX658-319
10|Ball Shooter Actuator Arm46000822
11|Hit Cover Vac-Form46000392
12|Ball Shooter Actuator Arm Rubber Bumper - version B46000857
13|Ball Shooter Actuator Arm Bearing - Upper46000394
15|Target Rubber46000396
16|Seesaw Cushion46000397
17|Ball Shooter Tip Rubber Bumper - version B46000668
18|Spring46000399
20|Seesaw Spacer46000401
21|Bearing FYH UPO0246000403
22|Rubber Block Bumper KA-2046000402
23|Ball shooter Actuator Arm Fixing Bracket - version B46000856
24|Hit Cover Actuator Arm Bumper46000823
25{Ball Shooter Actuator Arm Bumper - Lower46000824
26|Ball Shooter Actuator Arm Bearing - Lower46000825
27{Rocker Arm End Cover46000826
Page 61

Item Description Part No

1{Meter 3.5-6v65000002

Fuse Holder 63500786

.2A Q/B Fuse 20mm63500501

Fuse Holder 63500786

81.6A Q/B Fuse 20MM63500481
4|Pushbutton Switch60000059
5|Slide Switch60000023

1002 10w WW Pot 7600164

.Knob4400009
Page 62

Item Description Part No

1| Transformer67700021
2|Fuse 1..." 3A QB63500546
3.|SSR Board - Single Channel46000020
4|PSU Board46000414
5Tilt SwitchX000-300
Page 63

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 64

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.