Avalanche TM-096 1st Printing
Avalanche (Atari, 1978) · Technical Manual · 116 pages · 36 sections · original scan
AVALANCHE Operation, Maintenance and Service Manual
Complete with Illustrated Parts Catalog
GAME SERIAL NUMBER LOCATION
Your game's serial number is stamped on the circuit (back) side, bottom right corner, of the printed circuit board—see the illustration below. The same number is also stamped on the TV monitor chassis and on the labe! located on the rear of the game cabinet. Please mention this number whenever calling your distributor for service.
LOO ON awe
ATARI INC. 1265 BORREGAS AVENUE PO. BOX 9027 SUNNYVALE, CALIFORNIA 94086 408/745-2000 = TELEX 35-7488
AVALANCHE
Operation, Maintenance
and Service Manual
Complete with Illustrated Parts Catalog
A.
ATARI
Copyright © 1978 by Atari, Inc. All rights reserved Motorola and TEC service manuals reprinted by permission of Motorola Data Products and TEC Videoelectronics, Inc. No part of this publication may be reproduced by any mechanical, photo-
graphic, or electronic process, or in the form of a phonographic recording,
nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
For permission request, write:
ATARI INC 1265 Borregas Avenue P.O.Box 9027 Sunnyvale, California 94086
1G Lithographed in the U.S.A.
1 LOCATION SETUP INTRODUCTION GAME INSPECTION LOCATION OF SERIAL NUMBER . INSTALLATION REQUIREMENTS . . Power Requirements and Line Voltage Selection .... Temperature Range . Humidity Range ..... Location Space Requirements... Type ot Power Cord INTERLOCK AND POWER ON/OFF SWITCHES . VOLUME CONTROL . . SELF-TEST PROCEDURE OPERATOR OPTIONS ... pom
xOmm
2 GAME PLAY A. ATTRACTMODE ........ setereens veces 24 B. READY-TO-PLAY MODE 22 C. PLAY MODE . 2.2
3 MAINTENANCE AND ADJUSTMENTS A. CLEANING ..... : B. COIN MECHANISM . Components on Coin Door Access to Coin Mechanism Cleaning of Coin Paths Lubrication Adjustment of Coin Switch Trip Wire Mechanical Adjustments on Coin Mechanism . 34 General Troubleshooting Hints 34 C. TVMONITORADJUSTMENTS ..... 22.00.0000 cece tee eee 36 D. TVMONITOR REMOVAL - ee - 36 E. FUSE REPLACEMENT...... . tee . eee eee 37 F. LAMPREPLACEMENT |... 20.0.0. 00 coe cette eee eee 37 G. LICON SERVE SWITCH AND START SWITCH REPLACEMENT . 37 LICON Serve Switch . ee 37 Start Switches .............. os fees .. 37 H. PADDLEKNOB......... mere -. 37
Avalanche
TABLE OF CONTENTS
iv Avalanche THEORY OF OPERATION GENERAL INFORMATION ...... 02 eee eee nee ee ee eee eee eye POWER SUPPLY ...... 0.0.0 0c c eee e ees CRYSTAL-CONTROLLED OSCILLA TOR AND TV SYNC GENERATOR MICROPROCESSOR CLOCK MICROCOMPUTER . MICROPROCESSOR...... : MICROPROCESSOR WATCHDOG PADDLE CONTROL .. RAM MEMORY. .... ROM MEMORY . VIDEO. os ag cots cet wie cogs ee a ene ATT TOMO w> RoRaRaELIES
ILLUSTRATED PARTS CATALOG
TV MONITOR SERVICING INFORMATION Motorola Service Manual A. GENERAL INFORMATION . B, SERVICE NOTES .... Circuit Tracing... . . Component Removal . CRT Replacement .... Adjustments ....... Regulator Adjustment .... Horizontal Hold/Oscillator Adjustment . Vertical Height/Linearity Adjustment . . Focus Adjustment . Monitor Servicing ......... C. THEORY OF OPERATON : we Power Supply ...............05 +73 Volt Supply............. Video Amplifiers and Output D. HORIZONTAL DEFLECTION CIRCUITS . Phase Detector ........ Horizontal Oscillator .. . . Horizontal Pulse Shaper and Driver . Horizontal Output Syne Circuits .........-.. Vertical Oscillator and Output . Spot Killer. . Blanking Amplifier
TABLE OF CONTENTS
TEC VIDEOELECTRONIC INC. SERVICE MANUAL A. GENERAL o.oo cece teen eee 6-19 B. SPECIFICATIONS .... 0.000.000. 0 cc eee eee fog te Pe bape eo yg -- 619
Figure 1-7 —_ Location of Voltage - Changing Plugs on the Power eae severe eee 13 Figure 1-2. Location Space Requirements............. +f 14 Figure 1-3 Location of Interlock and Power On/Off 51 witches . 1-5 Figure 1-4 Location of Volume Control and Self-Test Switch. ... . 16 Figure 1-5 | Option DIP Switches on Came PCB........ Figure 2-1 Attract Mode.... Figure 2-2. Ready-to-Play-Mode Figure 2-3. PlayMode.. ee . Figure 3-1 Coin Door Assembly Lfard whe Figure 3-2. Hinging Open the Magnet Gate ‘Assembly ere Figure 3-3 Removal of CoinMechanism ........... Figure 3-4 — Surfaces to Clean Inside the Coin Mechanism . . Figure 3-5 — Removal of Plate Covering Rear of Coin Slot . Figure 3-6 Close-Up View of Lubrication Point ..... Figure 3-7 Detail View of Coin Switch and Trip Wire Figure 3-8 Adjustments on Coin Mechanism. . oe Figure 3-9 Location of Adjustments on TV Chassis . . Figure 3-10 TV Monitor and Fluorescent Lamp Removal. Figure 3-11 LICON and Button Switch Replacement .. Figure 41 — General Block Diagram of Avalanche Game .. . Figure 4-2 Functional Block Diagram of the Avalanche PCB. . . Figure 4.3 Harness Schematic Diagram .... 20.0000 ce eee Figure 4.4 Avalanche PCB Schematic Diagram Figure 4-5 Type B Power Supply Schematic Diagram Figure 46 Coin Door Schematic .... wee
Avalanche v
LIST OF ILLUSTRATIONS
vi Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7 Figure 5-8 Figure 5-9 Figure 5-10 Figure 5-11 Figure 5-12
Figure 6-1 Figure 6-2 Figure 6-3 Figure 64 Figure 6-5 Figure 66 Figure 6-7 Figure 6-8 Figure 6-9 Figure 6-10 Figure 6-11 Figure 6-12 Figure 6-13 Figure 6-14 Figure 6-15 Figure 6-16 Figure 6-17 Figure 6-18 Figure 6-19 Figure 6-20 Figure 6-21
Avalanche ILLUSTRATED PARTS CATALOG
Final Assembly ... 20.0.0... 00.00 e cece eee TV Shelf Assembly ..... Control Panel Assembly . Coin Door Assembly . . Front Bezel Assembly . Coin Lockout Assembly Coin Switch Assembly. . Type B Power Supply Type A Fluorescent Light Assembly RF Shield Board Assembly . Start Button Assembly . 7 es ties Avalanche PCB Assembly ..... 2.00.00 6 000 cece eee eee
Motoroia Monitor Circuit Board in Service Position. . Motorola Monitor Block Diagram. +73 Volt Supply Circuit . Motorola Monitor Vertical Drive Waveform . Motorola Monitor Video Amplifiers and Output Ci ircuit . Motorola Monitor Horizontal Deflection Circuit . Motorola Monitor Horizontal Deflection Waveforms . . Motorola Monitor Horizontal Output Circuit... .. Motorola Monitor Sync Circuit . Motorola Monitor Vertical Oscillator Circuit . Motorola Monitor Spot Killer Circuit ... veces Motorola Monitor Blanking Amplifier ............ Motorola Monitor Chassis Rear View - Component Location Motorola Monitor Circuit Board Detail - Solder Side ..... . Motorola Monitor Schematic Diagram.......... Motorla Monitor Circuit Board Detail - Component Location . TEC Monitor Chassis, Rear View . . TEC Monitor Chassis, Top View. : . 620 TEC Monitor Printed Circuit Board, Top View... .. 621 TEC Monitor Schematic Diagram . -- 6-27 TEC Monitor Wiring Diagram - 629
Table 1-1 Table 1-2 Table 4-1 Table 6-1 Table 6-2 Table 6-3
LIST OF TABLES
Self-Test eu Operator Options . . bees ee Microprocessor Input/Output Signal Descriptions . Motorola Monitor Electrical Specifications................. Motorola Replacement Part Numbers ... . . . : TEC Monitor Replacement Part Numbers ......... -. 616
Avalanche vii
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
9 bal LOCATION SETUP
A. INTRODUCTION Avalanche™ is a one- or two-player game developed by Atari. The game is contained in a distinctively styled upright cabinet which is illustrated with brightly colored graphics to enhance player appeal. A 23-inch TV monitor is mounted in the top front of the cabinet, with the monitor viewing screen tilted slightly from a vertical position. Player-operated controls are mounted directly below the TV monitor on the front of the game cabinet.
Two identical coin mechanisms are mounted on the lower front center of the game cabinet, below the player-operated controls. Either of these two mechanisms can initiate play. The cash box is located behind a locked access door below the coin mechanisms.
Avalanche ..
The object of the Avalanche game is to accumulate a high score by catching the “rocks” as they fall on the TV viewing screen. This is done by operating the paddle knob (potentiometer) on the player control panel. The degree of difficulty increases as the game progresses. The rocks become smaller while falling faster; the paddles decrease in size and decrease in number. For a detailed description of game play see Chapter 2.
B. GAME INSPECTION Your new Avalanche game is manufacured by Atari with the intent of being ready to play right out of the shipping carton. Your cooperation is needed to supply the final touch of quality control. Please follow the procedures below to ensure that your game is in perfect condition.
- Examine all external parts of the game cabinet for dents, chips, or broken parts.
nN . After determining that the game has been received in good condition, unlock and open the rear access door. Carefully inspect the interior and verify that:
@ All plug-in connectors are firmly seated.
@ All integrated circuits in sockets on the game printed circuit board are firmly seated.
@ The fuses are all seated in their holders.
@ No harness wires are disconnected.
@ No loose foreign objects are present, especially metal objects that could cause electrical problems.
Be sure all major assemblies are checked. Check the game printed circuit board (PCB), the transformer, the two coin mechanisms, the speakers, the fluorescent light, and the player controls. Also, be sure the TV monitor is secure in its mounting.
Cc. LOCATION OF SERIAL NUMBER The serial number for Avalanche is located on a metallic label in the upper left-hand corner on the back of the game cabinet. This serial number also appears in the corner (common te both edge connectors} on the back of the PCB, inside the game cabinet. See the inside front cover of this manual.
1-2. Avalanche D. INSTALLATION
REQUIREMENTS
Power Requirements and Line Voltage Selection
Avalanche is shipped for operation at 110 VAC, 60 Hz. Power consumption is approximately 150 watts. However, if your local voltage is not 110 volts, follow this procedure. You must select one of four connectors at the power supply and plug it into the voltage selection socket. Figure 1-1 shows the four connectors with one of them plugged in. The plugs are identified by wire color as listed in this figure. Note that there are two basic operating voltages — 110 VAC, 60 Hz, and 220 VAC, 50 Hz, with provisions for low line voltage in each case. To insure proper operation, measure line voltage. If voltage is consistently below 100 V (for 110 VAC lines) or below 210 V (for 220 VAC lines), use the low-voltage connections. Use the black plug for low 110 VAC lines and the green plug for low 220 VAC lines.
Temperature Range
Location and storage should not be below 0 degrees Celsius (32 degrees Fahrenheit), and no higher than 49 degrees Celsius (120 degrees Fahrenheit).
Humidity Range
Relative humidity for location or storage should be no more than 95%.
Location Space Requirements
The game requires a minimum of: @ 166 centimeters (651% inches) of vertical space. @ 64 centimeters (25% inches) of width clearance. @ 68 centimeters (27 inches) of depth clearance. @ 61 centimeters (24 inches) of player space.
Type of Power Cord
Atari has added a strain relief power cord to Avalanche. The advantage of this type of power cord is that, if pulled accidentally, the strain relief will hold the cord in place at the cabinet wall. The plastic strain relief “cushions” the impact of the shock and prevents the cord from pulling the wires out of the harness connector. Check the power cord assembly periodically for damage.
LINE VOLTAGE-CHANGING PLUG WIRE COLOR BLACK
installed at factor 210 VAC VOLTAGE
ON/OFF AND INTERLOCK POWER IN SWITCH
Cb
3 Amp, 250 V. SLOW-BLOW 8 Amp, 125V. Fast-Blow
2.5 Amp. 125 V. SLOW-BLOW
Figure 1-1 Location of Voltage-Changing Plugs on the Power Supply
E. INTERLOCK AND POWER ON/OFF SWITCHES To minimize the hazard of electrical shock while you are working inside the game cabinet, interlock switches have been installed at the rear access doors. This switch removes all power from the game while the access door is open. This switch removes all power from the game while the access door is open. To help you conserve energy, a power on/off switch has been installed on the game so that it can be turned off during closed periods. The switch is hidden on the back of the cabinet at the top, as shown in Figure 1-3.
Check ior proper operation of the rear access door interlock switch by performing the following steps: Unlock and open the rear access door.
Plug the AC power cord into 110-volt source. (If voltage is consistently less than 110 VAC, make sure that you change the voltage plug to the black plug.)
Set the power on/off switch to the on position by flipping the toggle switch toward the front of the game cabinet.
Close the rear access door. Within approximately 30 seconds the TV monitor should display a picture.
Slowly open the rear access door until the TV monitor picture disappears. The TV monitor picture
Avalanche 1-3
“25%”
Figure 1-2 Location Space Requirements
should disappear when the rear access door is opened less than one inch from the top.
- If the results of Step 5 are satisfactory, the interlock switch is operating properly. If the picture does not disappear as described, check to see if the switch is broken from its mounting or stuck in the on position.
- Close and lock the rear access door.
F. VOLUME CONTROL If volume is incorrect for your location, open the coin door and adjust the volume control. See Figure 1-4 for location of the volume control.
1-4 Avalanche G. SELF-TEST PROCEDURE Avalanche will test itself and provide data to demonstrate that the game’s circuitry and controls are working properly. This procedure uses the TV monitor and the speakers; no additional equipment is required. See Figure 1-4 for location of the self-test switch. To start the procedure over from the beginning, turn the switch off, then on again. This will return the test to Step 1 and can be done at any time during the procedure. See Table 1-1 for further details and instructions on the selftest. We suggest that you run the self-test procedure each time the coin box is emptied.
H. OPERATOR OPTIONS Options of the Avalanche game offer maximum player appeal for each game location. These options are
L INTERLOCK SWITCH 1 power onorr switcn
Figure 1-3 Location of Interlock and Power On/Off Switches
listed in Table 1-2. They are preset for a certain game setup during production. To determine how the switches have been set for your game, compare the TV monitor viewing screen during the attract mode with some of the information in Table 1-2.
To change the toggle positions of the switch assembly and set the desired options, the printed circuit board (PCB) must be removed according to the following procedure:
1, Unplug the game. Unlock and open the lower rear door assembly.
Locate the radio frequency (RF) shield assembly immediately inside the cabinet on the right. See Figure 4-5. (It is an aluminum box with small holes.) On one end of the box is a printed circuit board (PCB) with an edge connector coming from the edge of the board. Remove the five pan-head Phillips screws from each of the long sides (total of three screws) of the RF shield assembly.
Carefully remove the PCB from the RF shield assembly. Set the switches for the desired options, as shown in Table 1-2.
Reinstall the PCB following Steps 1 through 4 in reverse order. Do not force or bend the printed circuit board. Before reinstalling, always inspect the printed circuit board for damage. Close and lock the rear access door.
Plug in the game and verify options functions by playing it.
Avalanche 1-5
SS SELF-TEST SWITCH SHU
Figure 1-4 Location of Volume Control and Self-Test Switch
1-6 Avalanche
TABLE 1-1 SELF-TEST
TEST [ INSTRUCTION
RESULTS IF TEST PASSES RESULTS IF TEST FAILS
*4. | Unlock & open the coin door. Set the self-test slide switch (located inside the opening, above and slightly to the right.) See Figure 1-3
RAM and ROM test will follow.
The next phase of the selftest checks the lights, buttons, switches, and horizontal position control.
This phase of the selftest will “loop” or repeat itself until the switch is turned off. TV monitor becomes white for about one second, then becomes black for one second. Immediately following, the message RAM OK ROM OK
is displayed at the top of the TV screen, This means the RAM and ROM were checked, and both tested correctly.
Below the RAM OK message, ROM OK
a two-digit alphanumeric combination appears. This hexadecimal number is used to test the paddle knob (potentiometer) range. (See Test 2.)
All three buttons (LED Serve switch and both Player Start buttons) remain lit. If the RAM does not check correctly, the screen will display the message:
RAM BAD
If the ROM is at fault, the number of the bad ROM is displayed on the screen, For example, if ROM 0 and 3 are bad, the message ROM 03
appears on the screen. There are four ROMs programmed into Avalanche. They are 0, 1, 2, and 3.
One or more of the buttons are not lit ,
Turn the paddle knob (potentiometer) slowly from one end of its range to the other. The horizontal position control is read and its value is displayed in hexadecimal numbers below the RAM/ROM message. These numbers will increase or decrease evenly with no skips in the series. The value of the control should range from approximately 40 to 2 B8. It is normal for these numbers to vary slightly from time to time. Numbers in the series will be skipped. This indicates the potentiometer is “noisy” and must be cleaned with a tuner cleaner.
Press the Serve button, and the One Player Start and Two Player Start buttons.
Trip the right & left coin switch wires. A “ping” or “bleep” sound occurs each time a button is pressed,
The same sound occurs each time a coin switch wire is tripped. No sound indicates a stuck or broken switch, or an open or shorted harness.
- The first phase of the self-test procedure checks the memory, both RAM (random-access memory), and ROM (read-only memory). The second phase checks sound, iights, pushbuttons, coin detection and horizontal potentiometer control.
Avalanche 1-7
TABLE 1-2. OPERATOR OPTIONS
OPTION 8-TOGGLE SWITCH ON GAME PCB Toggle No: 1 2 3 04/5, 7 8
Game Language
German Spanish French English OFF OFF ON OFF OFF ON ON ON
Game Cost
Two Plays Per Coin One Coin Per Player Two Coins Per Play Free Play A0Z \ }
' \ \ L i) \
i ! ! I I
Misses Allowed Per Game
3 misses 5 misses Points Required for Extended Play
450 points 750 points ° Zz {2 oOmMmac =
No Extended Play Extended Play Enabled ON OFF
1-8 Avalanche
[—LUVUOTOTNNTTNTTNTINL |
| ft caution | = a inepep. moves | ee
ET. :
° 12345678910}
RF BOARD PCB
GAME PCB
Figure 1-5 Option DIP Switches on Game PCB
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
GAME PLAY
Avalanche has three modes of operation:
@ Attract — power applied or game has ended. @ Ready-to-Play — coins accepted. @ Piay — after one of the Start buttons is activated.
A. ATTRACT MODE (See Figure 2-1) The attract mode begins when power is applied to the game and the power switch is turned on. (The power on/off switch is located at the top rear of the cabinet, as shown in Figure 1-2.) This mode also occurs at the end of every game. When the proper amount of coins clear the coin acceptor, the attract mode ends.
Avalanche “=:
COIN 1 PLAVER
EXTENDED PLAY FOR 750 PIs.
Figure 2-1 Attract Mode
During the attract mode the TV screen shows rocks falling and being caught by four paddles (one on top of the other), moving horizontally across the screen. The TV screen displays the previous game score or scores, the standing HICH SCORE, the point total required for extended play, and the game cost or cost per game. The message, MISSES 3 or MISSES 5 is displayed at the upper left corner of the screen, depending on which option has been selected. (See Table 1-2 in Chapter 1.) The player controls and game sounds are inactive during this mode.
B. READY-TO-PLAY MODE (See Figure 2-2) When the correct amount of coins clears the coin acceptor, the ready-to-play mode is initiated. The TV monitor display no longer shows the rocks falling or the four paddles moving to catch the rocks. The coin message and the extended play message remain on the screen along with the previous game score or scores. MISSES (upper left corner of the screen) resets to 0.
1 COIN 2 PLAVER
EXTENDED PLAY FOR
Figure 2-2 Ready-to-Play Mode
2-2 The ONE PLAYER START button will light if there is credit for one game. Both start buttons will light if there is credit for two or more games. Only the start buttons on the control panel will activate during the ready-toplay mode.
Cc. PLAY MODE The play mode begins when one of the player start buttons is pressed. If the ONE PLAYER START button is activated, its light stays on for the remainder of the game and the light for the TWO PLAYER START button automatically goes out. If the TWO PLAYER START button is activated (provided sufficient credit has been granted), the opposite occurs.
Figure 2-3 Play Mode
When a one-player game is started, the PLAYER-2 score disappears from the screen, and the PLAYER-1 score flashes on and off. The SERVE button also blinks on and off until it is pressed, at which time it stays on untila miss occurs. It then blinks again until pressed. After game play begins the PLAYER-1 score remains stationary ‘on the screen, except between turns when it flashes on and off again.
When a two-player game is started, both player scores are displayed on the TV screen and the PLAYER-7 score flashes first. After the first player misses, the PLAYER-2 score flashes. Each player score remains stationary after the SERVE button is pressed. This pattern is repeated for each turn. The SERVE button characteristics are the same as for a one-player game.
Each time the SERVE button is activated, rocks begin falling from the top of the screen. If the SERVE button is not pressed within five seconds, the rocks begin falling automatically. The object of the game is to catch as many rocks as possible with any of the pad-
dles for a high score. This must be done before any rock reaches the playfield bottom.
In the beginning of each game there are six rows of tocks and six paddles. The first row of rocks are worth one point each; the last row are worth six points each, with the rows in between worth two, three, four, and five points each, ranging from large to small rocks respectively. See below.
Whenever a rock hits one of the paddles, the rock disappears and the appropriate amount of points are registered for that player’s score. As each row of rocks disappears, one more paddle is eliminated. The paddles become smailer until only one small paddle remains and ‘one small row of rocks remain. If any of the rocks reach the bottom of the playfield, a miss is recorded (upper left corner of the TV screen), the game momentarily freezes, and then progresses to the next tur. The degree of difficulty increases as the game progresses, since the rocks become smaller and the paddles decrease in number and size. The rocks fall at a faster rate as the game continues. However, the number of points awarded for each catch or hit also increases.
in the beginning of each game (whether a one or two player), misses are set at 0. When a miss occurs (or when each player misses in a two-player game), the count goes to 1, then 2 and so on until the game ends. The game can be set for three or five misses. See Table 1-2, Operator Options, in Chapter 1. If a player catches all of the rocks, the playfield is refilled with a new set of rocks. Game play is continuous during this transition, and the number of misses remaining for the game stays the same. Rather than starting with six large paddles, the player is given three large paddles when the playfield is reset with rocks. As the rocks are caught and disappear, the paddles gradually are reduced in size and number. If all of the rocks are again caught, the playfield is reset and the player is given two large paddles to start with. The paddles again are reduced in size and number as the rocks are caught. The playfield will reset with rocks once more, this time starting with one paddle which gradually is reduced in size. A player's score after catching all of the rocks for the first time would be 687. The highest possible score then would be 2748 (687 x 4 filled-up playfields).
Extended play for Avalanche is optional. See Table 1-2, Operator Options, in Chapter 1. If extended play is enabled and the game is set for three misses, an additional game is granted when the player scores a minimum of 450 points. If the game is set for five misses, extended play (an additional game) is granted for a minimum of 750 points. When this occurs the video is “flashed” at a fast rate and the words EXTENDED PLAY replace the GAME OVER message. The flashing continues for approximately five seconds, after which the player can play another game.
At the end of every game the TV screen freezes for about five seconds while the words CAME OVER flash on and off in the middle of the screen.
Each game function for Avalanche is accompanied by a distinctive electronic sound. These sounds range from low- to high-pitched noises. In addition, the sound of an “avalanche” of falling rocks is heard continuously throughout each game. The avalanche sound increases in intensity as the game progresses; the smaller the rocks become the more high-pitched the game sounds become when the rocks are caught.
Avalanche 2-3
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
If reading through this manual does not lead to solving a specific maintenance problem, you can call Tele-Help™ at the following two Atari Customer Service offices.
Atari Coin-Op Customer Service AD 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103 (Monday - Friday, 7:30 - 4:00 pm Pacific Time)
From California, Alaska, or Hawaii, dial (408) 745-2900
From anywhere else in this area, dial toll-free (800) 538-1611
EAST U.S.A.
Atari Inc. New Jersey Customer Service Office 46 Colonial Drive, Piscataway, NJ 08854 Telex 37-9347 (Monday - Friday, 8:30 - 5:00 pm Eastern time)
From New Jersey dial (201) 981-0490
From anywhere else in this area, dial toll-free (800) 631-5374
Avalanche
A. CLEANING The exteriors of game cabinets and Plexiglas® panels may be cleaned with any non-abrasive household cleaner. 'f desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the acrylic plastic panels, because any dust can scratch the surface and result in fogging the plastic.
B. COIN MECHANISM Components on Coin Door Figure 3-1 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted. Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechanisms. Powering the game causes the lock-out wires to retract far enough to allow genuine coins to reach the coin box. When AC power to the game has already been turned off, the lockout coil is de-energized, causing the lock-out wires to move out far enough to divert coins to the return chute.
Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire exten-
LOCK-OUT COIL LAMP HOLDER ding out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.
Also shown in the photograph is a slam switch assembly. It has been included to defeat any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.
Access to Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 3-2. Or, if necessary, each coin mechanism can be entirely removed from the door merely by pushing down on a release lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 3-3.
Plexiglas® is a registered trademark of Rohm & Haas Company.
Figure 3-1 Coin Door Assembly
3-2 Avalanche Figure 3-2 Hinging Open the Magnet Gate Assembly
Figure 3-3 Removal of Coin Mechanism
Cleaning of Coin Paths
By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling water and a mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed alr,
Figure 3-4 shows the surfaces to clean inside the coin mechanism. These include the inside surface of the
(CLEAN BOTH SURFACES WHERE COIN ENTERS THE MECHANISM, AS WELL AS THE MAGNET)
Figure 3-4 Surfaces to Clean Inside the Coin Mechanism mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these you can guide the point of a screwdriver or similar tool along the edge of the magnet.
If coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a 3/8-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 3-5). Removing the plate will provide access to the entire channel.
Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches.
Figure 3-5 Removal of Plate Covering Rear of Coin Slot
Lubrication Do not apply lubrication to the coin mechanisms. The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 3-6 shows this lubrication point.
Adjustment of Coin Switch Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of its trip wire should be as shown in Figure 3-7. Use extreme care when handling or touching these wires.
Avalanche 3-3
MANUALLY HOLD DOWN REJECTION BUTTON AND APPLY ONE DROP HERE
LOCK- OUT WIRE
Figure 3-6 Close-Up View of Lubrication Point
In Figure 3-7 you will note that the coin switch trip wire is oriented into the “V” of the secondary coin chute. The wire should extend to only about 1/8” beyond the chute.
A retaining clip holds the wire onto the switch actuating stud. If you should lose a retaining clip, all is not lost. Just crimp the switch actuating stud over the trip wire with a pair of pliers.
Mechanical Adjustments on Coin Mechanism Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take it to a clean well-lighted area where it can be placed in a vertical position on a level surface (such as a bench top). Besides a screwdriver, you will need a set of several coins, including both new and old, worn ones. Figure 3-8 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These adjustments should only be done by someone who has experienced in servicing coin mechanisms and who understands their operation.
3-4 Avalanche CORRECTLY ADJUSTED TRIP WIRE
Figure 3-7 Detail View of Coin Switch and Trip Wire
General Troubleshooting Hints The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted. If troubles still persist, check the conditions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism
ITEM IDENTIFICATIONS 1 Kicker and Separator Screws 2 Washers 3 Kicker 4 Separator 5 Gate Lever Spring 6 Gate Pivot Pin 7 Mainplate Assembly 8 "C” washer 9 Rail 10 Gate Assembly 12 Cradle Assembly
13 Upper Gate Pivot Spring 14 Undersize Lever Assembly 15 Magnet Gate Assembly 16 Magnet Gate Adjuster 17 Retaining Screws 18 Coverplate Assembly 19 Return Coverplate 20 Coverplate 21 Mounting Studs 22 Lower Gate Pivot Spring i Kicker and separator 23 Coin Release Lever
- Set the acceptor with the back of the unit facing you in the test position.
- Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws.
- Insert several test coins (both old and new) and note that some are returned by striking the separator. 4, Loosen the separator screw and move the separator a slight amount to the left. Lightly retighten the screw.
- Insert the test coins again and, if some are still returned, repeat Step 4 until all the coins are accepted.
- Loosen the kicker screw and move the kicker as far to the left as it will go. Lightly retighten the screw.
- Insert the test coins and note that some are returned.
- Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw.
- Insert the test coins again and, if some are still retumed, repeat Step 8 until all the coins are accepted.
- Be sure that both screws are tight after the adjustments have been made.
Magnet gate
- Set the acceptor with the front of the unit facing you in the test position.
- Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through.
- With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate.
- Test this adjustment using several other coins (both old and new) and, if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted.
- Fix the magnet gate adjusting screw in this position with a drop of glue.
Additional Cleaning
- Remove the transfer cradle (12) and the undersize lever (14).
- Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins.
- Replace the transfer cradle and the undersize lever.
- To be certain the coin mechanism is completely free of any residue, place the mechanism In boiling water for several minutes. Carefully remove it and let it air-dry completely before reinstalling in the door.
Figure 3-8 Adjustments on Coin Mechanism
Avalanche 3-5
rejects genuine coins, try to readjust it. \f this is not successful, then replace it with a working mechanism.
TV MONITOR ADJUSTMENTS
The TV monitor should be adjusted only when the picture is distorted or if the contrast or brightness seem out of adjustment.
The monitor's adjustments function like those of a conventional, home television set, except that the volume adjustment has no effect. Instead, the game produces its sound in circuits separate from the TV monitor. Figure 3-10 shows the location of the adjustments on both TV monitors used by Atari. Your game contains a TV monitor manufactured to Atari specifications by either Motorola or TEC Video electronics.
When making adjustments, follow these general guidelines:
BRITE (Brightness)—Perform this adjustment before the contrast. Adjust so that the white lines covering the screen just barely disappear, when the brightness is turned up.
CONT (Contrast)--Adjust so that the images are as bright as possible against the dark background without being blurred.
HORIZ HOLD (Horizontal Hold) or HORIZ OSC (Horizontal Oscillator)—Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered pictured.
VERT HOLD (Vertical Hold)—This needs adjustment only if the picture appears to be rolling up or down the screen. Adjust for a stable, centered picture.
TV MONITOR REMOVAL (See Figure 3-10) Remove three screws (button-head socket cap #10-32) at the top edge of the cabinet and remove the Plexiglas® retainer. Slide the Plexiglas shield
fA / \ commas \\ Ca Cen on 2 FUSES- Rewove Contaast + ‘RIGHTNESS BRIGHT HEIGHT ABNER Jo RERLACE: wontz. o8¢, Focus Z HORIZ. HOLD. VERT HOLD ws » VOLTAGE SWITCH (lave in ght postion}
TEC MOTOROLA MODEL TM- 600/623 MODEL MS5000/M7000
Figure 3-9 Locations of Adjustments on TV Chassis
3-6 Avalanche
out through the top of the cabinet, and remove the smoked Plexiglas screen which is immediately behind the shield. Next remove the cardboard bezel. At the back of the cabinet, remove the upper service panel door (four wood screws, #8 x 1%”). Remove the four carriage bolts (10-24 x 2.00” Ig.) that secure the monitor to the TV shelf assembly. Disconnect the TV monitor harness and slide the monitor out through the front of the cabinet. E. FUSE REPLACEMENT Avalanche contains seven fuses, five on the power supply assembly in the lower part of the cabinet and two on the TV monitor assembly. Power supply fuses are accessible through the lower rear door assembly. TV fuses are accessible through the upper service panel door. Replace fuses only with the same type as follows:
TEC TM-600/623 Monitors: 3AG 2-amp and 0.5-amp quick-blow, 250 volts Motorola M5000/M7000 Monitors: 3AG 0.8-amp quick-blow, 250 volts Power Supply: Fuses F1 and F2—3AG 3-amp slow-blow, 250 volts Fuses F3 and F4—3AG 2.5-amp slow-blow, 125 volts Fuse F5—3AG 8-amp fast-blow, 125 volts
F. LAMP REPLACEMENT (See Figure 3-10) Avalanche contains an 18-inch fluorescent lamp inside the top of the game cabinet assembly. To replace the lamp, remove the Plexigias® retainer, shield, and screen as described in Section D of this chapter (TV Monitor Removal). The fluorescent tube can now be pulled straight out of the cabinet and replaced.
G. LICON SERVE SWITCH AND START SWITCH REPLACEMENT (See Figure 3-11)
LICON Serve Switch
The SERVE button on the control panel contains an LED (light-emitting diode) switch. To replace the switch follow this procedure:
- Unplug the power cord. Unlock and open the coin door. Unlock and remove the lower rear door (for better interior lighting).
- Remove all wires from the suspected switch.
- Turn the switch counterclockwise while holding the cone-shaped nut on the outside of the game cabinet.
4, Install a new switch using the reverse procedure.
- Reconnect the harness wires. Plug in the power cord. Close and lock both doors.
Start Switches
The ONE PLAYER and TWO-PLAYER START buttons on the control panel are backlighted by two #47 lamps. The switch itself is a Cherry switch with goldplated contacts.
To replace the START button:
- Unplug the power cord. Uniock and open the coin door. Unlock and remove the lower rear door assembly.
- Reach in through the rear door and remove all wires from the suspected switch.
- Remove the four screws which secure two plates to the control panel.
- Reach in through the coin door. Squeeze both sides of the switch and pull out.
- Replace the switch using the reverse procedure (switch part #62-020).
To replace a START switch lamp:
- Reach in through the rear door and loosen the jamp mounting screws.
- Remove the faulty lamp and replace with a new #47.
- Plug in the power cord. Close and lock both doors.
H. PADDLE KNOB (POTENTIOMETER) The paddle knob on the control panel is a potentiometer made with resistive carbon material. After frequent use of carbon material begins rubbing off the potentiometer. This results in a fine dust which causes electronic noise and causes the paddles not to move smoothly. Also, during the self-test procedure the hexadecimal numbers do not count evenly. (See Chapter 1 for details on the self-test procedure.)
Avalanche 3-7
FLUORESCENT LAMP
CARRIAGE BOLTS BUTTON-HEAD SCREWS
~ PLEXIGLAS®
SMOKED PLEXIGLAS® SCREEN
CARDBOARD BEZEL
TV MONITOR REMOVAL
Remove Clear playfield Plexiglas shield Remove tinted playfield Plexiglas shield Remove Cardboard Bezel Unplug TV Monitor Chassis connector and remove four carriage bolts on TV shelf assembly
- Remove monitor Pens
Fluorescent Lamp Removal
- Remove attraction Plexiglas shield
- Gently rotate fluorescent bulb until it slips out of socket. Remove fluorescent bulb.
Figure 3-10 TV Monitor and Fluorescent Lamp Removal
3-8 Avalanche
START SWITCHES
SQUEEZE TABS, THEN PUSH THROUGH
LED SERVE SWITCH
SWITCHES #47 LAMPS \ TURN COUNTERCLOCKWISE
Figure 3-11 LICON and Button Switch Replacement
Avalanche 3-9
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
THEORY OF OPERATION
A. GENERAL INFORMATION The PCB block diagram of Figure 41 illustrates the major circuit blocks and their related controls—either on the board or remote. The input/output lines are also shown. Figure 4-2 is a general overview of the Avalanche game.
The game has a solid-state, self-contained television monitor which produces a picture quite unlike that of your home television screen. For example the broadcast signal arriving at your home television set is translated into a different video level as compared to the game video signal from the game PCB. The sound is generated by logic located on the PCB.
Avalanche
|INTERLOCK | [switch AC HORIZONTAL SOURCE. POWER DEFLECTION INTERLOCK' TRANSFORMER | SWITCH Vv MONITOR JvERTICAL DEFLECTION
PLAYER SELECT PUSHBUTTON LAM?
COIN MECHANISM
PADOLE CONTROL
‘SELF-TEST ‘SWITCH
Figure 41 General Block Diagram of Avalanche Game
4-2 Avalanche
Avalanche Figure 4-2 Functional Block Diagram of the Avalanche PCB
The composite video signal from the PCB is comprised of only two video levels instead of the more or less continuous shade of grey seen on a home television screen. The background of the picture is black video and the game objects are white video levels.
On the game PCB schematic diagram of Figure 4-4, the symbol “P” (appearing at various inputs of integrated circuit devices) indicates a connection of +5 volts DC through a pull-up resistor.
For easy location reference, the board is divided into sections. These sections are identified by letters A through M (skipping letters G, |, O and Q because they may be easily confused with numbers 6, 1 and 0 respectively) across the short side of the PCB. Sections are identified along the long side of the PCB by numbers 1 through 9. The letters and numbers create a grid, and all ICs are located on the PCB along the grid lines.
Located at L9 is an LM323 regulator mounted in a Jarge black heatsink and next to it is a 4-ohm, 10-watt resistor. These components produce a good deal of heat during normal operation. The temperature is not extreme, but sensitive skin may burn to the touch.
The harness schematic of Figure 4-3 illustrates how all the electrical and electronic assemblies are electrically connected.
B. POWER SUPPLY (See Figure 4-4, Sheet 1 of 4)
The PCB receives +10 volts unregulated and 25 VAC from the power supply chassis. The +10 volts is developed off-board and regulated by the LM323 to a stable +5 volts DC. This +5 volts DC is distributed throughout the board to power all circuits except the audio output. The 25 VAC input is rectified through diodes CR4 and CR5, filtered by capacitor C74 and supplied to the audio output circuit as unregulated +18 volts. This 18 volts is regulated by a three-terminal device 7812 (Q8) to develop +12 volts DC. The 25 VAC is also rectified through diodes CR2 and CR3, and regulated to —5 volts DC by the 7905 (Q7).
At the top of the PCB, most of the wide traces are DC ground. On the back of the board the wide trace along the long end of the PCB is +5 volts DC.
44 Avalanche C. CRYSTAL-CONTROLLED OSCILLATOR AND TV SYNC GENERATOR (See Figure 4-4, Sheet 1 of 4) The crystal-controlled oscillator generates a 12Mhz clock frequency (specifically 12.096 Mhz) that is used to produce all of the operating frequencies required of the game PCB.
The oscillator output (12 Mhz) is divided by the divide-by-two circuit to develop two 6 Mhz signals (designated as 6 Mhz and 6Mhz). The horizontal sync counters H1 and J1 are driven at 6 Mhz, which provide horizontal synchronizing pulses 1H through 256H. The HBLANK and HSYNC signals are developed in flip-flop K1. HSYNC is the clock input for the vertical counters J2 and K2 that provide the vertical synchronizing pulses IV through 128V. VBLANK AND VSYNC are developed by a specially coded ROM (read-only memory), K3.
The horizontal and vertical synchronization signals are used to produce a TV monitor raster made up of 252 horizontal lines at a frequency of 15,750 Hz (256H). Synchronized with line 0 is a vertical blanking pulse that occurs for the duration of 22 more horizontal scans followed by 240 lines of active video. The resulting total is 262 lines per frame.
D. MICROPROCESSOR CLOCK (See Figure 4-4, Sheet 2 of 4) The microprocessor clock 0 is a result of the PCLOCK signal—generated’ by 2H. The 2H bit is shifted by a 16-bit shift register comprised of devices M7 and L7, at frequency of 12 Mhz. On the Q10 output of device L7 (pin 5) the PCLOCK clocks a divide-by-two circuit (B5) which enters the MPU chip (B4) on pin 37 0.
A PCLEAR signal insures that ©0 has the proper phase relationship with the ROW/COL, MEMCAS and MEMRAS signals generated by the 16-bit shift register M7 and L7.
E. MICROCOMPUTER The microcomputer consists of read-only memory (ROM), random-access memory (RAM), and the microprocessor. The microprocessor controls the microcomputer operations through a 16-bit address bus that addresses the program ROMs. Address lines ABUSO through ABUS12 are multiplexed with the data signals to address the dynamic 4K RAMs. An 8-bit bi-directional data bus provides a path for transferring data between
the microprocessor and the various memories. A special watchdog circuit makes certain that the microcomputer functions properly.
Address lines ABUSO through ABUS12 are buffered to eliminate signal loading. These buffered address lines address the program ROMs (C/D2, D/E2, E2, C/D3, D/E3 and E3 for the -01 version and A2, B2 and C2 for the -02 version), The direct non-buffered address lines from the microprocessor are A13-A15.
F. MICROPROCESSOR (See Figure 4-4, Sheet 2 of 4)
The 6502 microprocessor (B4) is externally clocked at 00 by the Q output of latch BS on each PCLOCK pulse. The 0 clock also generates the 02 and 02 output clocks of the MPU.
The 6502 is a 64K-bit address-memory-mapped microprocessor device consisting of a 16-line address bus (ABUSO-ABUS15) and an 8-bit bi-directional data bus (DO-D7). The NMI is the only interrupt signal other than the direct reset input from the watchdog counter. When the RESET input goes low, the program counter is reset and started at a meaningful address.
To better understand the microprocessor (MPU) refer to Table 4-1 for a complete description of the data, address and control signals to the MPU. Only those control lines used are discussed. G. MICROPROCESSOR WATCHDOG (See Figure 4-4, Sheet 2 of 4) Watchdog is an external monitoring system that resets the program execution back to its initial sequence. This is accomplished by a watchdog statement, incorporated into program memory, that results in a WATCHDOG RESET pulse at the output of the address decoder.
The watchdog circuit is a 7490 counter. In normal operation the circuit is pulsed once each TV picture frame by the VBLANK pulse. If nine frames occur without a WATCHDOG RESET pulse, the counter resets the microprocessor. This prevents random electronic static from upsetting the game operation. The power-on circuit or the hardware for reset presets the counter, which in turn initializes the microprocessor and starts the attract-mode sequence.
H. PADDLE CONTROL (See Figure 4-4, Sheet 1 of 4) The paddle control is a linear clutched pot which is connected to the inverting input (pin 6) of comparator device K6. The control functions as the variable input to an analog-to-digital (A/D) converter circuit comprised of devices Q10, Q11, K6, Q3, M6 and J3.
A positive voltage ramp is generated by one-fourth of device K6 (pin 10) when FET Q10 is switched on by
TABLE 41 Microprocessor Input/Output Signal Descriptions
Signal Name Function
These sixteen lines are uni-directional MPU address lines to supporting memory (i.e., RAMs and ROMs) and I/O. This input line, when low, resets the MPU from either a power down or a high-going QD output from the watchdog counter. The contents of locations FFFC/FFFD in memory are loaded into the MPU program counter to point the start of a reset sequence. This input when going low indicates a non-maskable interrupt sequence. After the MPU concludes the current sequence, it will then proceed to the NMI sequence. System clock input. This output is the Read and Write signal line which indicates the direction of the data transfers on the MPU data bus. MPU system clock output.
Avalanche = 4-5
VBLANK pulse. When Q10 switches off, the voltage at pin 10 of K10 begins to rise as the capacitor C46 charges. This voltage continues to rise for the duration of the frame.
The voltage ramp is then buffered by voltage follower K6 (pin 12) finally to enter the non-inverting input of K6 (pin 5). As the paddle is moved, the wiper voltage of the 5K ohm pot varies from +5 volts to 0 volts; therefore the voltage at pin 6 varies accordingly. The voltage at K6 pin 5 is the result of the synchronous VBLANK pulse. The VBLANK pulse occurs at every vertical retrace for a duration of approximately 1.4 Msec everytime throughout the game.
When the paddle control wiper and the ramp voltage to the comparator (K6) cross, a pulse is generated that clocks the 8-bit latch J3. This device latches the eight inputs 1V to 128V corresponding to the time the clock input is pulsed by comparator K6. The outputs of J3 (DO-D7) are then read by the microprocessor during an IN2 pulse. This data is effectively the digital conversion of the analog pot voltage.
I. RAM MEMORY (See Figure 4-4, Sheet 3 of 4) The game memory consists of a 64K-bit dynamic RAM memory. This memory is comprised of sixteen 4,096 x 1bit (4Kx1bit) dynamic RAM devices, located at A6-J6 and A7-J7. These sixteen RAMs are then divided equally into groups of eight. Each group of eight may be selected individually by the 4KCS1 or 4KCS2 chip selects. The byte serial data RAM inputs (DBUSO- DBUS7) are buffered data bus out lines which originate
4-6 Avalanche from the microprocessor data bus outputs (D0-D7). Address information is strobed into the ROM memory address by the MEMCAS and MEMRAS signals. The data is permanently stored in memory by the low-going MEMWE Signal.
The data outputs (RAM 0-7) of each group of eight are both tied together. Parallel RAM 0-7 lines are converted to serial data (video signal) by shift register E5. These lines are connected to the microprocessor bidirectional data bus lines via the tri-state gates F5 and H5 when enabled by a RAM READ pulse.
J. ROM MEMORY (See Figure 4-4, Sheet 4 of 4) The ROM memory permanently contains program data such as the score display, audio level, “rock” display pattern and self-test routines. The ROM devices are programmed by Atari, Inc. and are field replaceable.
K. VIDEO (See Figure 4-4, Sheet 3 of 4) The composite video signal is generated by the output of RAMs A7 through J7 and A6 through J6 (Figure 4-4, Sheet 3 of 4). The parallel video data (DOUT) of each RAM is tied to an 8-bit parallel-to-serial shift register E5. The serial output RAM data is switched to a positive or negative video signal by Exclusive OR gate K5. The video signal is then clocked into the M1 latch by the 6Mhz clock signal. Each time a COMP BLANK signal occurs low, it resets the M1 latch (Figure 4-4, Sheet 1 of 4). The video signal is held low until the COMP BLANK signal returns to a high. This allows the M1 latch to blank the video signal.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
1lOVv ais OuT | ZIEN alw
TR
NOTIOE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction. forbidden withot specific, watten, permission ot Atal ‘Sunny GEiifonia“Inis srawing Ts only conditionally isa Seltnervocaipt ror possession (nereo confer oan {ny right n-o: canes to use, the subject mater of the Grawing of ‘any design or technical information. shown thereon, nor any ight reproduce ths drawing or any pat reol, excep! Tor manufacture by vendors of Atari, Ineor 3¢ mantutacture under the corporation's writ. reduce this drawing is granted eu) reo! uniess by wrilten agreement ‘wih or writen permission trom the corporation,
Figure 43 Harness Schematic Diagram
Avalanche
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Rio e
AL IOW az ft os 825,732 tet ee PuLLuP oe ov ves UNREes) ‘ -_ +1 cio Cl-4, @-15 17, 21-23, 25-29, ial T 32, 36,40, 48,52,58-60
| Ves ver | = | = | eyPaes |
; cas fr Waoor
| ne | a | sev |
+ oa esvac, ‘ J sree noe cre ie
| # | - | ae | wv |
Vas Sep VBLANE _ aes Tr
a zsver(al Ae 12), 3 3a}/®°—— _vaeseT vey r . Ta, Veestt
aR Ina001
HSYNC
ass
R30
NOTICE TO ALL PERSONS RECEWVING THIS DRAWING GONRDENTAL: Heprocuction Torben without the Spee walten.petmbsion ot ‘tary ine.” Sunnyvale, Eiiora Tn arbwig ony condoned, and Sather elpt ng: possession thereat contesortranafers Tey iit inso tenes toute, the subject mate of he SYNC. RAM CONTROL,
- or any ‘design ox technical inormation thereos, nor any right 10 reproduce this drawing o POWER, POT READING Mercer oscopl toomanuiacture by vendors of At Borated ond for manutacture under the corpora Feriigan, no cgi to reproduce ts crawing is granted Se SUb|sel alter hereof uniess by writer agreement Sian or wien permission fom fe corporation
Figure 4-4 Avalanche PCB Schematic Diagram A (Sheet 1 of 4)
Avalanche 4-11
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
NOTICE TO ALL PERSONS RECENING THIS ORAWING CONFIDENTIAL: Reproduction forbidden without the Specitic written permission of Ala, Inc.” Sunnyale, California. This drawing is only conditionally Issued, and Neither vecelpl nor possession thereof conters or transfers Any right in, oF license to use, the subject mattor of the drawing or any design or technical information. shown thereon, nor any right to reproduce this drawing or any part thereot, except for manutacture by vendors of Atari, incor: porated and for manufacture under the corporation's wit READ ” fen license, no ight to reproduce this drawing ts ganted my or ine subject mater thoreo o er agreement Pre ‘ith or written permission irom the sérporation, Aeuse ——>) a be
| aa | —4 | SOUNBTVL | | | be |
| sors. | e— | nea | | | bE |
| ais—4 | WATERDBG | zo /(WR—Lee | 31234 | pt |
| INSEL | WEL | 2 | mm | |
| = | Wee | " | i |
wT
| jASuSie | S2)3— | ease, | = |
p—— in +sv— a2e Shey
| 270 | ‘ | an | A | |
| a] caeoir | RVE | Lockour | ||
| SL | Was | tAMP | RB/wR | ies |
| [S__— arreacr | AcoLen | ie |
we weet 2 wae ae VRE ‘Ube = Wutoese Av! nue Pe away Sia] STAR R55, 220 Liaaiell +Sv VBLANK: 2
| wor | = | wey | See | 3 | NOVECARE, |
| ail | oe | came | |||
| LANGUAGE 1— | oye | I | 7 — DS |
us 3
| Lanauaceot = | 1 | +—*H> | V3 | og |
'
| crevit | \ | 4 | s | |
| cagpir da, og | i | 4 | fo | D3 |
| cxepis] a| | 3 | ; | it | wov |
| MoDEsh | + | 2 | be |
\ \
| crave $0 OE | \ Pvaver [H | 4 | > | +5, | ||
| SPARE, feromo ft | 2 PLAYER[S | 4—<1 | 2 | og, | ; | |
| a | 2seu | Bye | ||||
| | va | y= | AE | ||||
| 1 | e | Gg) | comr-ScaRe | |||
| swt | au | vol 53) | ZOMF STAR | |||
| I” | ae | ~ | 3 | 4u | Nuwaw | |
| misses 69-7 O | Tt | D3 | ||||
| mosses $ | 9 | _ | apt. | |||
| £ | re | ts | ||||
| = | 19) | 9 | Warm | |||
| coms F]}- | — | . | Ry | ve | 12[53)* | CORE TRE, |
. 2
| cone[S | * | > | bi |
| —* | las | bs |
sean [7] air] al
| rest [E | —- | { | bs |
‘ u starr [e, be
| ae | Zl | slat al alate | Te | 2v ew |
| ebay ay eb | abite | Le |
sw. mee
| ann WY | 7TeL | nS |
= anon
| sv | sit | fos | os |
+f b? TAT
I/D, MICROPROCESSOR
Figure 4-4 Avalanche PCB Schematic Diagram A (Sheet 2 of 4)
Avalanche 4-13
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
> > > > 23>
| aoa | aed | aad |
| obit | t+ + | t+ |
="
| LL | | fe fs ho= | |: fs |p |
B
- ea Ad —_| | AS Az —| Al | AS
——+ —t+
«7 F7 ¥7
| 20-1023 | SO -702 | 30-7023 | |||
| pis | pout} | Low | ovr) | | bin | dou |
| Fe | ps | je | [is | ||
| ns | 9 | 5c |
gg 3
| a | 2 | 2 | = |
ga Bs
ae 30-7023 Bin povt cers NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction” foraidden without the Specitic watten permission of Atari, Inc..” Sunnyvale, Gaivtomnia’ This drawing 1s only conditionally issued, and neither receipt nor possession thereof confers or tansters. any night in, oF license to use, the subject matter of the Grawing oF ‘any design or technical infor
fense, no right to reproduce this drawing is granted ubject maiter thereof unless by written agreement ‘wrltien permission from the corporation.
RAMS,
Deus2 RAM2 Deus!
RAMI
pause RAMs
Figure 4-4 Avalanche PCB Schema
A MEMeRS EMER WREMWE,
FS ar97
| elt | 9 | 07 |
1 1
| 4 | 1s. | oe |
' ‘
| ld | 3 | oa |
é bs.
i ‘ 2 Ww ay ; ot
e v6 RAW RERB
| 12 | it | be |
iat ha
| 4 | H | be |
us er97 rs RAM READ
13 RAM VIDED
ad
2 ow Ee ra 3 3 RAM MEMORY a
Diagram (Sheet 3 of 4)
Avalanche 4-15
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
MEMORY
waa
5000 Ds. rt
per THREE USD SELECTS WHICH OUTPUT oO UTS O00® CREDIT | LAMP, OOISATTRACT,
zo00 [Fwo cep SELECTS waicn B-BIT PUT
: 0200 TOIFFF BASE PACE, Seassua Dee. tke EA ees DBw= SERVE, DB7*VBLANK
Tere 2» +4; fiz] auvio 3 ie 1000u¢ Toaoo4 — [13
ALDIO ond
PROGRAM MEMORY, AUDIO
Avalanche 4-17
ayourjeay § gL-b ANNI DV LNG ASHI NO Nall NMOHS 7 Avo IG \s\\ | Na ? NoWos03S BOVLIOA baad Koll IAa/a LS\L-2n ete PWAaWwuUosaSNVUYL ‘ONUMAWEG SIAL ONIAISORU GNOSKad TIV BL SSIS
PCB A0OL555-01 “<1 ro -™~ R | Nia 7 @ | 2, COO uF wl | a| @I15Vv
L Y
TP
INTERLOCK
ON/OFF SWITCH BK - oo} BK W. v_|w
Figure 4-5 Type B Power Supply Schematic Diagram 007197-01 c
Avalanche 4-19
SLAM SWITCH
—_&Y go. e¥
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Reproduction, n_ permission
15 POS MOLEX
PLUG + MALE
COIN
COUNTER!
SWITCH #| (RIGHT )
TERMINALS LOCKOUT coiL BN BN/BK
COIN *1 CRIGHT)
030401-01 FRONT VIEW OF COIN DOOR
Figure 46 Coin Door Schematic
4-20 Avalanche
Srey 3285190 senseysa0 sr-1400 sy-74e00 37-02 sr1808 37-7408
ILLUSTRATED PARTS CATALOG
The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for the Avalanche game.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this catalog, and the serial number of your Avalanche game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
Avalanche
(aT) Za. (i)
ZEA (42,
JER. (40)
2 @—N
Final Assembly A030500-01 Figure 5-1
5-2 Avalanche : : SECTION A\=A\
| ae ye OraKING Gz)
- DEA.
benny
be pea, —~ i)
a 136)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction. forbidden without the specitic written permission of Atari, Inc... Sunn} ia. This drawing is only conditionally Is wr therao! conte’ or nr isto reproduce he drawing oa capt tormanactre by vendors ol ported an for mandlacur und thegorporalo's wi {entsanges nh this drawing s granted orn sobfeck matter ere eniees by wnttog agement with or weliten permission fom the corporation,
SECTION b-B NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction. fore! ith specific written. p fornia. This drawing 1s only condi neither receipt nor possession thereot any right in, o7 Hcense fo bse, the subject matter of the Grawing or ‘any design of technical in thereon, nor any right to reproduce this drawing or af thereat except for mariutaclure by vangors of Akar porated and for marutacture under the corporation's wnt {en license, no right to reproduce this drawing Is granted br the subject matter thereo! unless by walten agreement with 97 written permission from the corporation.
- 4 €A,
- 10 EA.
Figure 5-1 Final Assembly A030500-01
Avalanche 5-3
Figure 5-1 Final Assembly Parts List
| 1 | A030501-01 | 1 | Cabinet Assy with Graphics |
| 2 | A007197--O1 | 1 | Power Supply Assy, Type B |
| 3 | A030502-01 | 1 | Control Panel Assy |
| 4 | A006877-92 | 1 | Lower Rear Door Assy |
| 5 | A006917-01 | 1 | Flourescent Light Assy |
| 6 | AN30838-01 | 1 | T.V. Shelf Assy |
| 7 | A030504-01 | 1 | Decal -Location Diagram Assembly |
| 8 | 75-5120B | 2 | Carriage Bolts, #10-24 x 1.25 Lg |
| 9 | A009083-01 | 1 | Coin Door Assembly |
| 10 | A009262-04 | 1 | R.F. Shield Box Assembly (15*%"Long) |
| il | A007784-01 | 1 | Power Cord Assy, Strain Relief |
| 12 | A030727-01 | 1 | R.F. Shield PC BD Assembly |
| 13 | A030572-01 | 1 | P.C. Board Assy, Avalanche |
| 14 | 006305-01 | 1 | Printed Poly Bag |
| 15 | TM-096 | 1 | Operation, Maintenance and Service Manual, Complete |
with Illustrated Parts Catalog
| 16 | 006873-01 | 1 | Retainer, Plexglass |
| 17 | 030311-01 | 1 | Plexiglas, Shield W/Graphics |
| 18 | 009010-02 | 1 | Bezel, Cardboard |
| 19 | 009011-01 | 1 | Speaker, Grill Cover |
| 20 | 005233-01 | 2 | Rear Door Seal |
| 21 | 006319-02 | 1 | Copyright Decal |
| 22 | 75-5132N | 2 | Carriage Bolts, #10-24 x 2.00" Lg" |
| 23 | A007902-01 | 1 | Cash Box Assembly |
| 24 | ST-096 | 1 | Self Test Chart |
| 25 | 006870-01 | 1 | Coin Box Bracket |
| 26 | A030453-01 | 1 | Assy, Rear Door, Upper Service Panel |
| 27 | 75-040 | 6 | Washers, Split Lock, #10 |
| 28 | 48-004 | 2 | Speakers, 5 inch |
| 29 | 73-77004 | 6 | Rivets, 3/16" 0.D. x .68 Lg (.250 x .500 Grip) |
| 30 | 46-201302 | 2 | Fuses, 3 AMP |
| 31 | 78-6601216 | 1 | Alum. Foil, 1" Wide x 5" Long |
| 32 | 78-6601216 | 1 | Alum. Foil, 1" Wide x 12" Lg. (Approx.) |
| 33 | 82-8016 | 3 | Screws, Button Hd. Socket Cap. #10-32 x 1.00 Lg. |
| 34 | 75-99090006 | 3 | Wellnuts, Blind Hole Fastener #10-32 |
| 35, | 75-0108 | 8 | Washers, Flat, #10 |
| 36 | 75-S516B | 4 | Carriage Bolts, #%-20 x 1.00 Lg (Black) |
| 37 | 75-9118 | 2 | Hex Nuts, #10-24 |
| 38 | 75-O015S | 4 | Washers, Flat #% |
| 39 | 75-990505S | 4 | Hex Nuts, #4-20, Nylon Locking |
© A warner Communications Company
5-4 Avalanche
Figure 5-1 Final Assembly Parts List
Part Number DESCRIPTION
75-9318 82-1824 72-6610 72-6608 72-6808 72-6812 78-25001 A032562-01 A030690-02 72-6810 78-24007 Wing Nuts, #10-24 Wood Screws, #8 x 1s" Lg. Ft. Hd. Phil. Screws, S.M. Pan Hd. Phil. #6 x 5/8 Lg. Screws, S.M. Pan Hd. Phil. #6 x & Lg. Screws, S.M. Pan Hd. Phil. #8 x + Lg. Screws, S.M. Pan Hd. Phil. #8 x 3/4 Lg. Screw Down Tie Wraps Power Switches & Harness Assy Volume Control & Main Harness Assy Screw, SM Pan Hd Phil #8 X 5/8" Lg. Cable Tie, Heat Stabilized Na BURP EPH OP ENOS
Avalanche
jure 5-2 TV Shelf Assembly A030836-01
5-6 Avalanche NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specitic witten permission of Atari, Inc, Sunnyvale, Sailfornia. This drowing is only conalionally issued, and sneither recelpt nor possession thereot confers or transfers any right in, of license to use, the subject matter of the drawing oF ‘any design or technical informstion. shown thereoa, nor any right to reproduce this drawing or any par thereol: except for manufactue by vendors of Ata r manutacture under the corporal'on's wit 0 ght to reproduce tis drawing ' granted ‘nthe subjéct malter thereat unless by written agreement ‘wilh oF weitter permission from the corvoration.
Figure 5-2 TV Shelf Assembly Parts List
Part Number Description
030834-01 92-033 006874-01 75-5120B 75-040 75-010S 75-9118 78-6601216 75-015S T.V. Mounting Board T.V. Monitor, 23" Plexiglas Retainer Carriage Bolts, #10-24 X 1% Lg. Washers, Split-Lock, #10 Washers, Flat, #10 Hex Mutts, #10-24 Alum. Foil, 1" Wide X 10" Lg. (Approx.) Flat Washer, #5 ODIHRARWNK NEPUMNUOREE
© 4 Warner Communications Company
Avalanche 5-7
W TNLSd
{ “NLS
a
< = iy J > v
Q
lay @) Nas
Figure 5-3 Control Panel Assembly A030502-01
5-8 Avalanche wien or wetter reproduce ti cramng hereoh unis by wntter agreement ‘asion from fe corporation
Figure 5-3 Control Panel Assembly Parts List
ATARI
Part Number Description
| 1 | 030310-01 | 1 | Control Panel W/Graphics |
| 2 | 001856-01 | 1 | Bushing, Alum. |
| 3 | 62-002 | 1 | Led Switch, Lighted |
| 4 | A030691-01 | 1 | Control Panel Harness Assembly |
| 5 | 19-9022 | 1 | Pot, 5K, Slip Clutch |
| 6 | 73-812 | 1 | Knob, Black W/Skirt |
| 7 | 75-5120BX | 2 | Carriage Bolts, #10-24 x 1.25" Lg., Black |
| 8 | 75-040 | 2 | Lockwasher, #10, Split |
| 9 | 75-9115 | 2 | Hex Nuts, #10-24 |
| 10 | A007357-O01 | 2 | Start Button Assembly (With Lights) |
© Aware: Communications Company
Avalanche 5-9
- ¥ 2 PLCS @))
- 2 PLCS
- 2 PLCS @1) 2 PLCs 2 PLCS @2)
@
@)
4 PLCS Qi)
YEL YEL/BK 4 pics BK/VEL
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Rerroduction, forbidden without the Specitic written. permission of Al Gaitornias Tis arswing 8 only cond ‘elther ecelpt nar possession thereat ight in, oF Heanse to Use, th ny ght to reproduce ts drawing or ary part i for manacture by venders OF ata cor or man loctore unr he Srperatons wr right to repreduce this crewing ‘granted ortne sutfoct mater heros ungssby mitonaprboren ‘ith or wetten permission from te sorporation,
Figure 54 Coin Door Assembly A009083-01 Cc 5-10 Avalanche
Figure 5-4 Coin Door Assembly Parts List
NYNYAaoeasa aa RBBRSSSVAARSHIOSOPNMGAYN Part Number
A007637-01 A007637-02 A007637-03 A007637-04 A007637-05 A007637-06 A007637-07
75-9165 A030362-01 A007640-01 A002465-01 004320-01 004341-01 004344-01 004340-01 004337-01 004338-01 004336-01 004326-01 75.046 006904-01 007359.01 70-11-47 73-3008 75-9914001 75-0268 75-00516 008629-01 71-2118 71-1225CU 71-125FB 71-1205FF 71-1201MG 71-1201KS 74-1210PE 71-1220CA 007753-01 A007638-01 A006921.01 Ref. pDUDDD 22000 pee De ee Se
MIAN GAONAANANFANNHANAANAA
Ref. Ref. Ret. Ref. Ref. Ref.
L Description
Front Bezel Assy.—Used only on -01 Coin Door Assy. Front Bezel Assy.—Used only on -02 Coin Door Assy. Front Bezel Assy.—Used only on -03 Coin Door Assy. Front Bezel Assy.—Used only on -04 Coin Door Assy. Front Bezei Assy.—Used only on -05 Coin Door Assy. Front Bezel Assy.—Used only on -06 Coin Door Assy. Front Bezel Assv.—Used only on -07 Coin Door Assy. See Figure 5-5 Nut, 6-32 Coin Lock-Out Assembly, See Figure 5-6 Coin Switch Assembiy, See Figure 5-7 Coin Counter Assembly Coin Door Weldment Secondary Coin Chute Key Loop Spring Return Bracket, Wire Form Lock-Out, Wire Form, R.H. Lock-Out, Wire Form, L.H. Button, Scavenger Lock Washer, #6 Spacer Lamp Socket Lamp Retaining “C” Ring, Truarc #5103-25 Self-Threading Nut, Tinnerman #SR188006 Washer, #6 Kepnut, Style 842, Stl., 6-32 Spring Lock Assembly, Hudson Lock Coin Mechanism for American Quarter Only Coin Mechanism for Belgian 5 Francs Only Coin Mechanism for German Mark Only Coin Mechanism for Swedish Krona Only Coin Mechanism for Japanese 100 Yen Only Coin Mechanism for English 10 Pence Only Coin Mechanism for Australian 20-Cent Piece Only Plate, Anti-Probe Switch Assembly, Siam Harness Assembly
Avalanche 5-11
- enc
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction forbidden without the ‘Specitic written permission of Atari, Ine,” Sunnyvale, California. This drawing is only conditionally issued, and ‘either receipt nor possession thereof conters or transters, ‘ny right In, oF leenee to Use, the subject matter of the drawing of ‘any design or technical information shown tMhereor, nor any right to reproduce this drawing or any part tMereo!, except for manutacture by vendors of Ata, Incor porated and for manufacture under the corporation's wnt ing is granted by writien agreement ‘permission trom the corporation
Figure 5-5 Front Bezel Assembly A007637-01 thru -07
5-12 Avalanche D 2 pics 4
s)encs 2Ppucs
a)epucs
Figure 5-5 Front Bezel Assembly Parts List
Description Bezel Ring Coin Shield Primary Coin Chute Bearing, Scavenger Button Clamp, Price Plate Price Plate Retaining "C" Ring, Truarc #5103-37 Mach. Scr., 6-32 x k Lg. Pan Hd., Phil Washer, #6, Split-Lock Self-Threading Nut, Tinnerman #SR188006 See below 004331-01 004332-01 004327-01 004329-01 See Below 73-3009 72-1604S 75-046 75-9914001 ANEBNENNNNN EH i L
Ere 2 TEM 7 [DENOMINATION] SO4sS0-o1 loousra-ci | 25¢ CO4sS0-O1 |Soun4s-o6| SFR SS5153 -0) loovsss -o4 [| 1 OM COUSSO-01 [CONS4S-OS | 1 KR SS5570-G1 [Oo4sGS-08 | 1COY ISO775e-61 |COUSSS-O2| 16 PF COTS! - 31 [OO4B4S-0O7 [207 AOST
© 4 warner Communications Company
Avalanche 5-13
NOTES: When ENERGIZED wSoer) . ° Freee a1 Se so * 222 Movemctor eee. an)
$380 ws © SES STATIC DIMEN JON
J WIN. eaD.t¥e-
Ruy cou (an RovnesD-o1)
|—z09-—>|
- Dimensions shown are dim's req'd. to interchange & repiace relay with existing equipment in field and production. » Break & deburr ail sharp comers.
- Dimensions taken from tooled part. Dimensions with * are specified dims. required in tooling by Engineering to have part interchange with prior buyout part. 4, Coll data: 10 VDC +2, 50.0 resistance current 200 ma maximum. 5, Manufacturer: Goin Mech, Inc.
Figure 5-6 Coin Lockout Assembly A030362-01 A
5-14 Avalanche DETAIL OF RELAY COIL (A007639-01} 3} { 1,06
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Reproduction forbidden without the specific writen permission of A’arl, Inc., Sunnyvale, Caltfornia. This drawing is only conaitionaily issued, and neither raceipt nor possession thereat centers or transfers any righ in, oF icense to Use, the subject matter of the Grawing of ary design or technical information shown thereon, nor any righ te reproduce itis draving or any part thereof ‘except for manufacture by vendors of Ata, incor arated and for manutacture under the corporation's wit. fen license, no “ght to repreduce this drawing '= granted OF the subject matter thereot uniess by written agreement ‘with or written permission kom the corporation.
Prehadhedde
ePucs NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL ‘Reproduction forbidden without the speciticsiten, permission oF Atari Inc,” Sunnyvale, falifornia. This drawing ts only conditionally issued, and either receipt nor possession neveot conters or anaters any right in, or license to use, the subject matter of tne Srawing oF any design or technical information sbown thereat nor any rightto repreduce this drawing ay ary part thereot, except Tot manutactee by vendors of Alan, incor porated and for manutactare Under the Corporation's wilt. {en license, no right to reproduze this drawing ts granted ar the subject matter thoreot unless by written agreement ‘with or written permission trom the corporation,
rem PART NO. DESCRIPTION lary
ISOUS4S-O1 Switcn hTG PLATE. v
Coerraral SWITCH, OMRON C-5G3-3] 1 [2-HaA 4412 ISCRMS, SH -HOCHLRE TAPPING] 2 Salt luin|—|
IS0B824-01 WiREFORM cueeey [1
Figure 5-7 Coin Switch Assembly A007640-01 D
Avalanche 5-15
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Repreducton,iatrdden. without the specie “ontten, peribgion Aa inc,” Sunny, fifomie. This drawing 9 only conditionally issued, and nether receipt nor possession thereof conters or transters ny Manton Hegnse to Use, the subect matter of he Growing of any design or technical information, shown 1, nor any ght 10 reprodk rawing a ‘man
Figure 5-8 Type B Power Supply A007197-01 H
5-16 Avalanche 8 iS REQD
Figure 5-8 Type B Power Supply Parts List
A009266-01 Power Supply Base Weldment Assembly A006886-01 Transformer Termination Assembly "Type B" 29-053 Cap., Sprague Electrolytic 26,000uf @ 15V 78-70501SC Brkt., Cap. Mtg. Sprague #4586-48 A006555-01 P.C. Board Rectifier
79-4411004 Fuse Holder, Panel Mounting 41-2003 Filter, Power Line, 5 AMP A006958-01 Volt Sel Block 95V A006958-02 Volt Sel Block 110V A006958-03 Volt Sel Block 205V A006958~04 Volt Sel Block 220V 78-2708 Grommet ,Plastic 72-1810S Screw Pan Hd., #8-32x 5/8"Lg.
75-048 Washer, Split-Lock #8 75-9188 Nut Hex #8 75-0185 Washer Flat #8 A007192-01 Power Switch Termination A007444-01 Power In Harness 46-203801 Fuse, 8 AMP, 125V, 3 AG Fast Acting 46-201251 Fuse, 2% AMP, 125V, Slow Acting
© * vere Conmanecatons Company
Avalanche 5-17
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Reproduction forbi iio written, permission Of ian inc, "Sunnyvale, hia. This drawing Is only co ‘and neither recs wossessionthoroolcortars ov ranafers any right in, nso to use, the subject mater of the Grawing or ign or tecnica nformation shown thereon, nor 0 eproguve. this drawing or any part ee ‘excopt or manulecture by vandors of Aa e0r
LogGO- +O" SO- Ll Oly Go- ‘ON, oMd
Nis v2 "ay Nive x NZ ‘NI Bf NI be I "NI 2 "NI QI azs 4H91I7 45
Nisi NZ “wl 28 NLOOI “NI OO! NI ZB Ni Ze “NEOL Rikers "MOOI "NrOOI HIHONST SSSNBVH ‘3.10N 33S
2i— “ON nel
"Ni He Bzis
“NT = NBT Hi Bas | SSANAVH |] AHO 74]
Bion
Figure 5-9 Type A Fluorescent Light Assembly A006917-01 D
5-18 Avalanche Qo3a 2
Figure 5-9 Type A Huorescent Light Assembly Parts List
ATARI
——— —= Part Number Qty. Description
| 1 | 93~104 | 1 | Gibson Fluorescent Fixture 18 inch |
| 2 | 70-303 | 1 | Fluorescent Tube 18 inch (or Equivalent) |
| 3 | A006916-01 | 1 | Fluorescent Light Harness, 100" |
| 4 | 78-2652 | 1 | Grommet, Rubber |
| 5 | 78-24001 | A/R | Tie Wrap | |
| 6 | 79-561816 | 2 | Wire Nut, Ideal 71-B |
Avalanche 5-19
PITT EET IEri i
- LOCATE APPROXIMATELY WHERE SHOWN | FARSIDE
2) CDEFHIKUMNPRSTUVWKYE om} fh c90000900 388833 TIT lore ee fo) 234567 BIONIZB 4 IS RIT 16 19202 22 4S PLACES .SMALL
IND.
NOTICE TO ALL PERSONS RECI
- 9 PLACES \SMALL CAP
Figure 5-10 RF Shield Board Assembly A03072701 A Avalanche 5-20
Figure 5-10 RF Shield Board Assembly Parts List
Part Number Description if P.C. Board Connector, 44 Pin P.C. Mount Cap, Cer Disc, 0.luf, 25V Cap, Cer Disc, 0.luf, 25V (Small, Bottom Row) Inductor, 100uh Inductor, 100uh (Small, Bottom Row) Jumper, .60 Centers Jumper, .30 Centers Decal, R.F. Shield Label 006549-01 79-517222 27-250104 27-A250104 41-3003 41-3004 52-003 52-004 009468-01 e COIKHHRUNH BPUIHBORREH
© A warmer Communications Company
Avalanche = 5-21
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL! Reproduction forbidden without the specie written permission of Alan, Inc, Sunnwale, fornia This drawing is only conditional issued, and inereot confers or vansters neither receipt nor possession Zany right in, oF license to ust Srawing ar 'any design thereon, nor any right to reprodi formant fen forthe subject matter thereot unless by watten agreement With oF written permission trom the corporation
“ABS TAN WOeLNOD
Figure 5-11 Start Button Assembly A007357-01 D
5-22 Avalanche Sd + SDdh OBanNoad Sy wacios sud 2 DIAG} sneh
[item | Part Number | Qty
| 1 | 006530 -01 | 1 |
| 2 | 006535 -01 | 1 |
| 3 | 006532 -01 | 1 |
| 4 | A006533-01 | 1 |
| 5 | 79-4317 | 2 |
| 6 | 70-11-47 | 2 |
| 7 | 62-020 | 1 |
| 8 | 72-1603 | 6 |
| 9 | 82-8808 | 4 |
| 10 | 75-9188 | 4 |
| ir | 75-048 | 4 |
| 12 | 004577-19 | 2 |
| 13 | 75-046 | 6 |
© 4 warner Communications Company Figure 5-11 Start Button Assembly Parts List
Description
Bezel Button Chassis Switch Mtg. Plate Assembly Lamp Socket Lamp Switch, Cherry, E68-50A Mach’ Screw, 6-32 x7sLg, Pan Hd, Phil. Screw, Button hd socket 8-32x 3 1g. Black Nut, 8-32 Washer, #8, Split-Lock Jumper Wire, Black
Washer, Split-Lock #6
Avalanche 5-23
NOTICE To ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without iN specitic written permesion of Alar, Inc.. Sunnyvale Galtornia. TW drawing te only concitionally lasued. an neither recelpt nor possession inereot conters or transfers ‘any right in, oF license to Use, the subject matter of the Srawing oF ‘any design or technical information shown hereon, nor any right to reproduce this drawing or any part tiereot, exces for manulacre By vendors of Ata Mea porated and wufacture under the Corpo: {er license, no right to reproduce ths draw ter thereot uniess By written agreement isston from the corporation. ort
«wou? TNOSBRK Z0-
WDA
Figure 5-12 Avalanche PCB Assembly A030572-01
5-24 Avalanche A (wowed Nolstaa10- NMONS 3¥ saws 11785 do LBS wIOT ADaIge-wadIIE
90-6010
Figure 5-12 Avalanche PCB Assembly Parts List
01 Version
ATARI’
Item Part Number Qty Description 1 030574-01 1 P.C. Board 2 10-5220 2 Res, Carbon, 5%, 4W, 22 OHM R31, 33 3 10-5181 1 * 7 " " 180 Ld R57 4 10-5331 5 " " " " 320 " R1,3,4,48,49 5 10-5471 3 " i " " 470 - R8, 38, 39 6 10-5102 25 = " " " Ko" R2,5,7,10,14-22,26, 29,30,32,37,41,51-
7 10-5222 2 " " " " 2.2K " R11,40 8 10-5392 1 x ‘ “oon 3.9K" R45
- 10-5562 1 " " " " 5.6K " R23 r0 10-5822 1 : . " " 8.2K " R46 11 10-5103 4 " " " " 10k " R9,13,27,28 12 10-5123 1 " " " " 12K" R43 13 10-5153 1 " " " " isk " R42 14 10-5223 1 . " " " 22k =" R44 is 10-5333 2 " " " " 33K" R47, 50 16 10-5683 2 " “ " " 68K " R34,35 17 10-5104 1 " " " " 100K " R24 18 10-5114 1 " " * i" 110k " R25 19 10-5105 1 " * " " im " R12 20 19-315503 1 Trimpot, 50K OHM R36 21 19-805W4P0 L Res, Wirewound, 10W, 4 OHM R60 22 10-5821 1 | Res, Carbon, 5%, W, 820 OHM R6 23 10-5393 1 |Res, Carbon, 5%, ‘sW, 39K OHM R61 24 10-5221 2 “ " non 2200" R58,59 25 21-101104 1 Cap, Mylar, 100V, -luf C46 26 24-250105 2 " Elec., 25V, luf c71,73 27 24-250475 2 ad " " 4.7uf C31,47 28 24-250106 2 " " ” lout c19,70 29 24-250227 1 " “ " 220uf clé 30 24-250108 1 a " 1000uf C72 31 24-250228 1 7 = " 2200uf C69 32 24-250478 1 " " : 4700uf C74 33 27-250102 1 i Cer. Disc, 25V, .O0Oluf C62 34 27-250103 1 " " " " -Olut C67 35 27-250334 i) ? " 7 7 .33uf C35,38,41,43,45,50, 53,55,57 27-250224 1 " " " " ~22uf C75
© 4 Warner Communications Company
Avalanche 5-25
A ATARI item | Part Number a 37 | 27-250104 38 | 28102221 1 39. 4. 42 | a1-inoig 2 43 | 31-1Naoo2 4 46 | 3¢-2Ne068a 2 47} 39-205461 1 sa | 34-2n3643 5
- 34-2n5190 1 50 | 37-7400 2 si | 37-7¢02 1 52 | 37-7404 4
- | 37-74Hoa 1 54 | 37-7408 9 ss | 37-7416 1 56 | 37-7420 2 57 | 37-7432 1 58 | 37-7442 2 59 | 37-7474 5 eo | 37-7a874 L e1 | 37-7486 L 62 | 37-7490 1 63 | 37-74164 2 64 | 37-7aLs164 2 65 | 37-74174 1 6s | 37-74175 L 67 | 37-74n8257 4 68 | 37-7408374 1 69 | 37-r0a1004 1 70 | 37-4138 1 ni | 37-8797 4 72 | 37-9316 4
- | 37-9336 L ya | 37-tn323 1 ys | 37-7622 L 76 | 37-7905 L aL a2 | 62-co1 Fa 93 | 66-1ieprr Fi ea | 72-1608¢ 2 as | 75-016 2
Figure 5-12 Avalanche PCB Assembly Parts List -01 Version DESCRIPTION
Part Number cap, Cer. Disc, 25v, .1ut "Dipped Mica, loov, 220pf Diode, 1no14 Diode, 1Ng001, ‘Thyrister, 2N6068A ‘Transistor, 2N5461 Transistor, 2N3643 ransistor, 2N5190 Integrated Circuit 7400 " » 7402 = "7404 7 " 74H04
- "7408 74166 "7420 "7432 “ 1aaz 7474 74874 7486 7490 74164 Tausi64 74174 74175 748257 74us374 Audio AMP ‘TDALOO4 Integrated Circuit 4136 fi pmereeed ” "9316 " "9334 Regulator, M323 i 7812 " 7905 Switch, SPST, MoM Switch, SPST, x8, DIP Washer, Lock, Int. Star, #6
1-15,17,18, 20-30, 87 | 75-916c 32 2a | 72-1408¢ 40,42, 44,48, 4 89 | 75-014 51,52,54,56,58- 90 61,63-65,68 on
- 92
93 | 78-0601, 94 | 009470-01 95 | 78-13026 crl,2 96 | 78-16095 cR3-6 97 96,9 100 | 79-42040 920 101 g1-4,11 102 95 103 | 90-102 #8, KB. 104 Le 105 AL,F1,C5,M6 106 | 90-6010 pL 107 | 90-7023 12,a3,8/83,B/C3, D4,£4,c8,08,"a BS 108 | 006s00-02
109 | 930611-01 110} 030612-01 112 | 030613-01 jas2 | 030614-02 a3 | 030615-01 030616-01 sal Screw, Pan Hd., Ph., 6-32 X 4 Lg. Cres Washer, Flat, #6
HB e per erento Nut, Hex, #6-32 Cres Screw, Pan Hd., Ph., 4-40 X 4 Lg. Washer, Flat, #4 Washer, Lock, Int. star, #4 Nut, Hex, #4740 Cres silpad Heatsink (1M323: Heatsink (TDA1008) Cement (TDA100¢ Heatsink) Silpad (1323) Socket, 40 PIN, Med. Insertion crystal, 12-096 siz Microprocessor RAM, 7023 syne Prom Prom 7800-7FFF Hich " 800-6FFF High 7900-77FF High 7800-7FFF Low S800 E#PF Low 7000-17FF Low
Cres. v2 a4 AG, B6,C6,D6,E6,F6,| 6 ,36/A7,B7,C7,D7, E7,27,H7,07 Ka c/pz b/E2 c/p3 D/R3,
5-26 Avalanche
Figure 5-12 Avalanche PCB Assembly Parts List
02 Version
ATARI
Part Number Qty. Description 1 030574-01 1 P.C. Board 2 10-5220 2 Res, Carbon, 5%, 4W, 22 OHM R31, 33 3 10-5181 1 " x — igo" R57 4 10-5331 5 " a “oe 330" R1,3,4,48,49 5 10-5471 3 " " — 470" R8, 38,39 6 10-5102 25 " " "oe 1K" R2,5, 7,10,14-22,26, 29,30,32,37,41,51-
7 10-5222 2 " " " " 2.2K " R11,40 8 10-5392 1 " J "oe 3.9K " R45 9 10-5562 1 " " noo 5.6K" R23 10 10-5822 1 4 " " 4 8.2K " R46 ll 10-5103 4 a . . 10K" R9,13,27,28 12 10-5123 1 ” 7 so 12K" R43 13 10-5153 1 : ¥ us isk * R42 14 10-5223 1 7 7 oo 22K" R44 is 10-5333 2 " " " " 33K" R47, 50 16 10-5683 2 . 2 "7 68k " R34,35 17 10-5104 1 " " " " 100K “ R24 18 10-5114 1 " " _ 110K " R25 19 10-5105 L " x so" im" R12 20 19-315503 1 Trimpot, SOK OHM R36 21 19-805W4P0 L Res, Wirewound, 10W, 4 OHM R60 22 10-5821 1 Res, Carbon, 5%, ’W, 820 OHM R6 23 10-5393 1 Res, Carbon, 5%, ‘iW, 39K OHM R61 24 10-5221 2 " " wow 2200 R58,59 25 21-101104 1 | Cap, Mylar, 100V, .luf c46 26 24-250105 2 " Elec., 25V, luf C71,73 27 24-250475 2 * " " 4.7uf 31,47 28 24-250106 2 bi " " 1Ouf ¢19,70 29 24-250227 1 ® " " 220uf C16 30 24-250108 1 # « “ 1000uf c72 3L 24-250228 1 ‘ * a 2200uf ce9 32 24-250478 L 7 " " 4700uf c74 33 27-250102 1 "Cer. Disc, 25V, -OO0luf c62 34 27-250103 1 “ " x . -Oluf C67 27-250334 9 ” " " " 33uf C35, 38,41,43,45,50, 53,55,57 27-250224 1 " " " “ + 22uft c75
© warmer Communications Company
Avalanche 5-27
a7 27-250104 26-101221 3i-1N91a 31-1N4001. 31-2N60688 39-2N5461 34-2N3643 34-2N5190 37-7400 37-7402, 37-7404 37-74804 37-7408 37-7416 37-7420 37-7432 37-7442 37-7474 37-74874 37-7486 37-7490 37-74164 37-74LS164 37-74174 37-74178 37-74L8257 37-7418374 37-TDA1004 37-4136 37-8797 37-9316 37-9334 37-1M323 37-7812 37-7905 62-001 66-116PIT 72-1608C 75-016 75-056 Part_Nunber
js DESCRIPTION cap, Cer. Disc, 25v, .1uf "Dipped Mica, 100v, 220p£ Diode, 1N914 Diode, 1Na001 ‘Thyrister, 2N6o6sB ‘Transistor 2N5461 ‘Transistor, 2N3643 Transistor, 2N5190 Integrated Circuit 7400 "7402 7404 7404 7408 "74166 “7420 "7432
- 7aq2 "7474 "74874 "7486 "7490 " 7a164 ~ 7408164 “74174 "74175 “7408287 . “ yans374 Audio AMP TDALOOS Integrated Circuit 4136
- "9316 " "9334 Regulator, 14323 7 7812 bs 7905, Switch, SPST, MOM switch, SPST, x8, DIP Serew, Pan Hd., Ph., 6-32 4 Lg. Cres Washer, Flat, #6 Washer, Lock, Int. star, #6
Figure 5-12 Avalanche PCB Assembly Parts List 02 Version
Item | Part Number 1-15,17,18,20-30,| 87 | 7$-916c
eB | 72-1408¢ a9 | 75-014 go | 75-054 61, 63-65,68 91 | 75-9148 ces 92 | 7e-16006
93 | 78-06002. 94 | 009470-01 95 | 7e-13016 crl,2 96 | 7e-16005 cR3-6 97 26.9) 100 | 79-42040 gio 201 Qt-a,11 102 95 103 | 90-102 Ha, Ke 104 16 105 AL,F1,C5,Mé 108 | 90-6010 pL 107 | 90-7023 12,A3/R/B3,B/C3, D4,B4,C8,D8,Me BS j108_ | 006400-01 M3 109 BL 110 MS,L8 111 KL,LL,ML,¥2,B5 12 aL DS 15 | o30608-01 Kaya Ji16 | 030609-01
030610-01 F4,F5,H5,95 BL/J1,52,X2 Fe sw2 SW.
PB peepee ee bee Nut, Hex, 46-32 Cr Screw, Pan Hd. Ph Washer, Flat, #4 Washer, Lock, Int. star, #4 Nut, Hex, 4-40 Cres silpad Heatsink (M323) Heatsink (TDALOO4) Cement (TDAL004 Heatsink) Silpad (1¥323) Socket, 40 PIN, Med. crystal, 12-096 MHZ. Microprocessor AM, 7023 Syne Prom Rom 7800-7PFF " 7000-778F " 6800-6FFF
Insertion 40 X 4 Lg. Cres
wa QBB
Avalanche 5-28
Tee
TV MONITOR SERVICING
INFORMATION
This chapter provides servicing information taken from the Motorola and TEC service manuals. Each manual has been reprinted by permission of the respective monitor manufacturer.
Your game will include either the Motorola or TEC monitor, depending on their availability during production.
Avalanche
MODELS M5000-155 M7000-155
MOTOROLA Service Manual
A. GENERAL INFORMATION This manual contains information on the M5000/M7000 monitor series and the +5 volt logic power supply. The M5000 uses a 19-inch CRT and the M7000 uses a 23-inch CRT. All CRTs are of the magnetic deflection type with integral implosion protection.
All monitor power supplies are capable of producing both +73 and +12 volts regulated from either 115-volt or 230-volt AC input to the transformer primary. All monitor variations described herein require a composite video input signal.
No work should be attempted on an ex- SAFETY
posed monitor chassis by anyone not familiar with servicing procedures and precautions.
. Safety procedures should be developed by habit so that technicians rushed with repair work automatically take precautions.
. A good practice, when working on any unit, is to first ground the chassis and to use only one hand when testing circuitry. This will avoid the possibility of carelessly putting one hand on chassis or ground and the other on an electrical connection which could cause a severe electrical shock.
. Extreme care should be used in handling the picture tube as rough handling may cause it to implode due to atmospheric pressure (14.7 Ibs. per sq. in.). De not nick or scratch glass or subject it to any undue pressure in removal or installation. Model Video Input 19” CRT 23” CRT| IM5000-155 Composite x | IM7000-155 Composite x LL
All monitors employ: four stages of video amplification, atwo-stage sync separator, a two-stage vertical integrator, a four-stage horizontal sweep circuit, a three-stage vertical sweep Circuit, a one-stage spot kill, a one stage blanking amplifier; and a regulated, full-wave bridge power supply.
Model Breakdown Chart
When handling, safety goggles and heavy gloves should be worn for protection. Discharge picture tube by shorting the anode connection to chassis ground (not cabinet or other mounting parts). When discharging, go from ground to anode or use a well-insulated piece of wire. When servicing or repairing the monitor, if the cathode ray tube is replaced by a type of tube other than that specified under the Motorola Part Number as original equipmentin this Service Manual, then avoid prolonged exposure at close range to unshielded areas of the cathode ray tube. Possible danger of personal injury from unnecessary exposure to X-ray radiation may result.
. An isolation transformer should always be used during the servicing of a unit whose chassis is connected to one side of the power line. Use a transformer of adequate power rating as this protects the serviceman from accidents resulting in personal injury from electrical shocks. It will also protect the chassis and its components from being
6-2 & MOTOROLA DataProducts _ canot stream, ILLNols 60187 PART NO. 68P25253A47 COPYRIGHT 1977 BY MOTOROLA, INC. PRINTEDIN U.S.A.
damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.
uw . Always replace protective devices, such as fishpaper, isolation resistors and capacitors and shields after working on the unit.
a . Before returning a serviced unit, the service technician must thoroughly test the unit to be certain thatit is completely safe to operate without danger of electrical shock. Do not use a line isolation transformer when making this test. Tega 1000-0HM/VOLT (OR HIGHER! AC VOLTMETER 1, REPEAT EACH CHECK WITH THE LINE CORD REVERSED IN THE POWER OUTLET 2, METER READING MUST NOT EXCEED T#VOLTS Ac. Notes: Pens a Rego — oe “HOT” LEAD OF METER TO EACH EXPOSED PART OF CABINET,
AS WELL AS THE CABINET
GROUND LEAD OF METER TO ANY EARTH GROUND SUCH AS A COLDWATER PIPE “Ng
Voltmeter Hook-up for Safety Check In addition to practicing the basic and fundamental electrical safety rules, the following test, which is related to the minimum safety requirements of the Underwriters Laboratories, should be performed by the service technician before any unit which has been serviced is installed in a game again.
A 1000-ohm-per-volt AC voltmeter is prepared by shunting it with a 1500-ohm, 10-watt resistor. The safety test is made by contacting one meter probe to any portion of the unit exposed to the operator such as the cabinet trim, hardware, controls, knobs, etc., while the other probe is held in contact with a good “earth” ground such as a cold water pipe.
The AC voltage indicated by the meter must not exceed 7% volts. A reading exceeding 7% volts indicates that a potentially dangerous leakage path exists between the exposed portion of the unit and earth ground. Such a unit represents a potentially serious shock hazard to the operator.
The above test should be repeated with the | power plug reversed, when applicable.
Never reinstall a monitor which does not pass the safety test until the fault has been located and corrected.
Table 6-1 Motorola Monitor Electrical Specifications
MODEL M5000-155 MODEL M7000-155
PICTURE TUBE
standard
POWER INPUT 19" measured diagonally (48.2 cm); 184 sq. inch viewing area (1188 sq. cm); 114° deflection angle; integral implosion protection; P4 phosphor
115/230 VAC, 110 Watts (nominal); 60 Hz provision for 230 VAC, 50 Hz 23” measured diagonally (58.4 cm); 282 sq. inch viewing area (1820sq. cm); 110° deflection angle; integral implosion protection; P4 phosphor standard
FUSES M5000-155, M7000-155—0.8A
+73 VOLT SUPPLY to 260 VAC Electronically regulated over AC inputs from 103 VAC to 130 VAC, or 260 VAC
VIDEO INPUT | 0.5 Volts to 2.5 Volts P/P maximum, composite for 50V at CRT 500 lines at picture center RESOLUTION
LINEARITY Within 3%, measured with standard EIA ball chart and dot pattern
Avalanche 6-3
Table 6-1 Motorola Monitor Electrical Specifications
r HIGH VOLTAGE 17KV (nominal)
HORIZONTAL a . + BLANKING INTERVAL| /7 microseconds typical (includes retrace and delay)
SCANNING . : | artical FREQUENCY Horizontal: 15,750 Hz+500 Hz; Vertical: 50/60 Hz
ENVIRONMENT Operating temperature: 10°C to 55°C (ambient) Storage Temperature: —40°C to +65°C Operating Altitude: 10,000 ft. maximum (3048 meters) Designed to comply with applicable DHEW rules on X-Radiation CSA certified for use in coin-operated amusements in a combustible enclosure UL listed under specification 1410 (electronic components)
TYPICAL 14.11" H, 18.18" W, 14.83" D 16.72" H, 21.56” W, 16.18” D DIMENSIONS (35.8 x 46 x 37.6 cm) (42.4 x 54.7 x 41 cm)
Specifications subject to change without notice.
B. SERVICE NOTES
Cirenit Tracing Component reference numbers are printed on the top and bottom of the three circuit cards to facilitate circuit tracing. In addition, control names are also shown and referenced on the schematic diagram in this manual.
Transistor elements are identified as follows: E—Emitter, B—Base, C—Collector.
Component Removal Removing components from an etched circuit card is facilitated by the fact that the circuitry (copper foil) appears on one side of the circuit card only and the component leads are inserted straight through the holes and are not bent or crimped.
It is recommended that a solder extracting gun be used to aid in component removal. An iron with a temperature-controlled heating element would be desirable since it would reduce the possibility of damaging the circuit card foil due to over-heating.
The nozzle of the solder extracting gun is inserted directly over the component lead and when sufficiently heated, the solder is drawn away, leaving the lead free from the copper foil. This method is particularly suitable in removing multi-terminal components.
6-4 Avalanche CRT Replacement Use extreme care in handling the CRT, as rough handling may cause it to implode due to high vacuum pressure. Do not nick or scratch glass or subject it to any undue pressure in removal or installation. Use goggles and heavy gloves for protection. In addition, be sure to disconnect the monitor from all external voltage sources.
- Discharge CRT by shorting 2nd anode to grouad; then remove the CRT socket, deflection yoke and 2nd anode lead.
- Remove CRT from the front of the chassis by loosening and removing four screws, one in each corner of the CRT.
Adjustments A non-metallic tool is recommended when performing the following adjustments.
Regulator Adjustment
- Connect the monitor to an AC line supply; then adjust supply to 120 volts (240 volts in some applications).
- Apply test signal to proper input. Signal should be of same amplitude and sync rate as when monitor is in service.
- Adjust HOR. SET coil L1 until display is stable.
- Connect a DC digital voltmeter or equivalent precision voltmeter to the emitter of the regulator output transistor, Q17, or any +73 volt test point.
- Adjust the 73V ADJUST. control, R93, foran output of +73 volts. Do not rotate the control through its entire range; damage to the monitor may result.
- When adjustment is complete, the AC line supply can be varied between 103 and 130 volts AC to check for proper regulator operation. With the regulator operating properly, changes in display size should be negligible.
Horizontal Hold/Oscillator Adjustment Adjust the core of HOR. SET coil L1 until the horizontal blanking lines are vertical or the CRT display is stable (synced).
Vertical Height/Linearity Adjustment
- Connect a test generator whose output is similar to the display signal normally used.
Figure 6-1 Motorola Monitor Circuit Board in Service Position
- Rotate the vertical size control, R60, until the smallest display is obtained.
- Adjust the vertical linearity control, R64, until the top and bottom of the test pattern is equally spaced.
- Readjust R60 until the desired display height is obtained.
- Readjust R64, if necessary, as in Step 2 above.
Focus Adjustment The best overall focus of the display is obtained by adjusting the focus control, R42, for best focus ata point which is near the center and approximately 1/3 down from the top of the display.
Monitor Servicing The monitor circuit board may be installed in a service position to provide easier access to the circuit foil when servicing the monitor (see Figure 6-1).
C. THEORY OF OPERATION Power Supply The power supplies are transformer-operated, full-wave, regulated supplies which maintain constant output voltages for input line variations of 103 volts AC to 130 volts AC, or 206 volts AC to 260 volts AC. Regulation of the output voltages is accomplished by using positive feedback through the integrated circuit reference amplifier.
+73 Volt Supply (See Figures 6-3, 6-4) When the +73 volt supply attempts to increase, the voltage at pin 3 of IC1 will increase, while the voltage at pin 2 remains constant due to D20. The increasing voltage at pin 3 will cause the output voltage of the reference amplifier (pin 6) to increase the forward bias of Q19. The collector voltage of Q19, forward bias of Q18, and the base current of Q17 will all decrease. The resultant proportional increase of Q17 collector-to-emitter voltage will cancel the attempted output voltage increase.
When the +73 volt supply bus attempts to decrease; the voltage at pin 3 of IC1 will decrease while the voltage at pin 2 remains constant. The decreasing voltage at pin 3 will cause the reference amplifier output voltage at pin 6 to decrease the forward bias of Q19. The collector voltage of Q19, the forward bias of Q18 and the base current of Q17 will increase. The collector-to-emitter voltage of Q17, which is in series
Avalanche 6-5
COMPOSITE EMITTER VIEO yNPUT FOLLOWER ogo GNO
REGULATOR
| 445/230, | Regul ATED | ‘3 | i | SHAPER |
ge ( SUPPLY oe ‘ 0 i
Kitt
| SYNC | ‘SYNC. | year. | VERT. | VERT. | |
| SEPARATOR | ane. | wieetioa | an | ose. | ORWER |
Figure 6-2 Motorola Monitor Block Diagram
f° ag 150 “1 po) nc. sel qu? Asw I
Figure 6-3 +73 Volt Supply Circuit with the output, will decrease proportionally to the attempted decrease in the outbut bus.
Resistor R84 shunts a portion of the output current around Q17 so less power is dissipated within the device. Resistor R82 is the current-limiting resistor for Q18, and R86 controls the leakage current of Q17. Resistors R83 and R85 are the collector load for Q19, and R88 and R87 provide an emitter voltage for Q19 within the range of IC1’s output voltage variations. Capacitor C45 filters high frequency variations from the voltage at pin 7 of IC1, and C49 is a Miller-effect capacitor which eliminates instability.
6-6 Avalanche r , PARABOLA | FROM EMITTER | OF Q17
EXISTING VERTICAL, SAWTOOTH WITHOUT VERT.PARABOLA ADDED
PARABOLA PULSE AND. VERTICAL SAWTOOTH ADDED TOGETHER, HENCE PRODUCING THE REQUIRED VERT. DRIVING SIGNAL
Figure 6-4 Motorola Monitor Vertical Drive Waveform
r 473V. +150V . ait aus 1K vi0EO 7 ™ [ PReame + RIL P/0
| PL | a | 7 |
composite VIDEO dee) + ee a
| weut | | | 0 | p2s | 6.8K |
| | | Srl | sav | | |
| t | al | RZ |
gud *<] 162K JIf= D2 =~ 50 cae AIS 5 B30PF y022 >< VIDE! CONTRAST a Torre aa AML LT torn? |
| 10.033 | = | = | aise | | | (CATHODE) |
ae VIA R78 To Qt0 To Qu GANTTER cou tecTOR ____]
Figure 6-5 Motorola Monitor Video Amplifiers and Output Circuit
Capacitor C32A filters horizontal frequency variations from the output bus.
Resistor R91 provides bias current for D20, and the value of R99 presents an impedance from pin 2 of IC1 to AC ground (through D20). Capacitor C46 couples high frequency voltage variations, which occur at the output bus, back to pin 3—preventing oscillations for proper operation of the reference amplifier. Resistors R92, R93, and R94 provide voltage division such that the adjustment of R93 can be set equal to the voltage of pin 2 of IC1. Resistor R95 provides bias current for D27 and also provides the +12 volt output. Diode D23 is necessary to temperature-compensate for variations within D21. Capacitor C32B filters AC variations from the output of the full-wave bridge.
Video Amplifiers and Output (See Figure 6-5) The composite video signal is coupled to the emitter-follower Q1 through the input connector P1 and capacitor C1. Transistor Q1 is a buffer stage which matches the impedance of the signal source to the video preamplifer and the sync separator stages. Resistor R1 is a terminating resistor for the video signal source, and resistors R2, R3, R4, and R5 form the biasing network for the stage. Capacitor C2 bypasses higher video frequencies to ground. The composite video signal is coupled from the emitter of Q1 to the sync separator Q10 through C33 and to the contrast control R6 through C47.
The contrast control varies the amplitude and couples the composite video signal to the base of Q2 through capacitor C3. Transistors Q2 and Q3 are complimentary, direct-coupled, common emitter amplifiers. The voltage gain (approximately 12) of the preamplifier stage is controlled by the feedbatk arrangement of R9, R10, R11, and R12. Resistors R7 and R8 provide the base bias voltage for Q2. Capacitor C4B is used for high-frequency peaking.
The output of the video preamplifier stage is coupled to the video output stage through capacitor C4. Diode D2 clamps the video signal to approximately +0.7 volts (DC restoration) when async pulse turns on the sync amplifier Q11, The video output stage is connected in a cascade configuration. Transistor Q4 is a common emitter amplifier and Q5 is connected in a common base arrangement. Capacitors C7, C8, and resistor R16 are used for highfrequency compensation, and resistor R18 controls the gain of the stage to approximately 47. Diode D3 maintains the base of Q5 at +6.2 volts, while capacitor C5 filters the video signal variations from the base voltage. Resistor R13 provides a DC bias path for D2, and R19 and D4 are used to limit the current through the CRT.
Avalanche 6-7
6 ss HORIZ PULSE Qa ASF HORIZ OSC, R29 7 p2s SHAPER HORIZ DRIVER n sy R32 con HORIZ DRIVER 5
R34 YW 3.3K yaw
Figure 6-6 Motorola Monitor Horizontal Deflection Circuit
Capacitor C10 AC-couples the video from the collector of Q5 to the cathode of the CRT if D4 turns off due to high beam currents. Resistor R17 is the collector load for Q5, and R15 provides the bias current for the zener diode D3. Capacitors C9 and C6 filter video frequencies from the +150 volt and +12 volt supplies. Resistor R14 and zener diode D1 are used to supply +12 volts for Q1, Q2, and Q3.
D. HORIZONTAL DEFLECTION CIRCUITS (See Figure 6-6) Phase Detector (See Figure 6-7) The phase detector consists of two diodes (D5 and D6) in a keyed clamp circuit. Two inputs are required to generate the required output, one from the horizontal sync amplifier, Q11, and one from the horizontal output circuit, Q9. The required output must be of the proper polarity and amplitude to correct phase differences between the input horizontal sync pulses and the horizontal time base.
The horizontal output (Q9) collector pulse is integrated into a sawtooth by R24 and C12. During horizontal sync time, diodes D5 and Dé conduct, which shorts C12 to ground. This effectively clamps the sawtooth on C12 to ground at sync time. If the horizontal time base is in phase with the sync (waveform A), the sync pulse will occur when the sawtooth is passing through its AC axis, and the net charge on C12 will be zero (waveform B). If the horizontal time base is lagging the sync, the sawtooth on C12 will be clamped to ground at a point negative from the AC axis. This will result in a positive DC charge on C12 (waveform C). The positive polarity
6-8 Avalanche causes the horizontal oscillator to speed up and correct the phase lag. Likewise, if the horizontal time base is leading the sync, the sawtooth on C12 will be clamped at a point positive from its AC axis. This results in a net negative charge on C12 which is the required polarity to slow the horizontal oscillator (waveform D).
Components R23, C15, R25 and C17 comprise the phase detector filter. The bandpass of this filter is chosen to provide correction of horizontal oscillator phase without ringing or hunting. Capacitor C13 times the phase detector for correct centering of the picture on the raster.
Horizontal Oscillator The horizontal oscillator employs the principles of the Hartley-type oscillator. Its operating frequency is sensitive to its DC base input voltage, thus permitting the frequency of the oscillator to be varied by the output voltage of the phase detector. The main frequency-determining components are L1, C19, and R28. The oscillator operates as a switch being biased alternately into saturation and cut-off. The initial forward starting bias is supplied via R26.
Horizontal Pulse Shaper and Driver The horizontal pulse shaper Q7 serves asa buffer stage between the horizontal oscillator and driver. Capacitor C20 and resistor R30 combine to shape the input waveform to the required duty cycle of 50%, which is necessary to drive the horizontal output stage.
A REFERENCE HORIZ, SYNC
OSC,ON FREQ g 0 NO CORRECTION VOLTAGE DEVELOPED
OSC,SLOWS, POS. CORRECTION VOLTAGE
OSC. FAST, NEG. CORRECTION VOLTAGE
Figure 6-7 Motorola Monitor Horizontal Deflection Waveforms
The horizontal driver Q8 operates as a switch to driving horizontal output transistor Q9 through T1. Because of the low impedance drive and fast switching times, very little power is dissipated in Q8.
Resistor R35 and capacitor C21 provide damping to suppress ringing in the primary of T1 when Q8 goes into cut-off. Resistor R36 is used for limiting currentin the collector of Q8, and C22 filters the horizontal frequency variations from the DC side of the transformer primary. Horizontal Output (See Figure 6-8)
The secondary of T1 provides the required low drive impedance for Q9. Resistor R37 limits current in the base of Q9, while capacitor C23 provides additional reverse bias to keep Q9 turned off during the horizontal retrace pulse. Transistor Q9 operates as a switch which once each horizontal time period connects the supply voltage across the parallel combination of the horizontal deflection yoke and the primary of 12. The required sawtooth deflection current through the horizontal yoke is formed by the L-R time constant of the yoke and output transformer primary. The horizontal retrace pulse charges C27 through D8 to provide operating voltage for G2 of the CRT. Momentary transients at the collector of Q9, should they occur, are limited to the voltage on C27, since D8 will conduct if the collector voltage exceeds this value.
The damper diode D7 conducts during the period between retrace and turn-on of Q9 to reduce retrace overshoot; capacitor C28 is the retrace tuning capacitor. Capacitor C25 blocks DC from deflection yoke. Components R38 and C26 are damping components for the width and linearity coils. Capacitor 32D is charged through D10, developing the video output supply voltage.
B HORIZ_ LIN Cs | Ley Lan HORIZ YOKE woni2g8 wioTH oui, 02 ne 028 | gs “ 259 Hav. RECT. to i og? oo wot we ve] io Howe orver HO ensine a MeTER ome To pI a couizctoR i HeaTeR VoLTaGe| Re FOR Vi 20) cz] | eae en 1.5K agit TO PIN R37 z Have TRANS. 10 10 cer Re 2nd ANODE
+3 YS. Toc a7 rap y SKS 36k To cm car [_ [om Revie TT aco |oww a)
Figure 6-8 Motorola Monitor Horizontal Output Circuit
Avalanche 6-9
Tog. EMITTER
Figure 6-9 Motorola Monitor Sync Circuit Syne Circuits (See Figure 6-9)
The video signal is coupled from the emitter of Q1 to the base of Q10 through C33. The negativegoing sync tips turn on Q10 and are clamped to the value of the base voltage due to the base-emitter diode junction. The video information within the composite video signal, however, is less negative and Q10 remains off between each sync tip. Therefore, the waveform at the collector of Q10 will contain only the composite sync pulse information,
Resistors R45 and R46 provide base bias for Q11. The composite sync pulses are amplified and inverted by Q11 where they are coupled to the vertical sync integrator Q12, the horizontal phase detector, and the video clamp diode D2. Resistors R47, R48, and R49, are the collector load for Q11, and also provie base bias for Q12, Resistor R50 limits current through the base-emitter junction of Q12, and R51 is its collector load. Components R52, C34, R53, C35, and R54 form a double integrator which removes the horizontal pulses from the composite sync signal, leaving the vertical pulses to be amplified by Q13 and coupled to the vertical oscillator.
Vertical Oscillator and Output (See Figure 6-10) The vertical oscillator is a relaxation oscillator and operates at a free-running frequency that is set by r— +73
RSE. SelK: >) R66
woos 3% | Rse ° COLLECTOR BK oe
343K: . 6027 VERT. osc. cao cal os f= Tors 100} O.1 as enw B2v VERT. OUTPUT L4B VERT. YOKE R67
20 ve
Figure 6-10 Motorola Monitor Vertical Oscillator Circuit
6-10 Avalanche
the value of resistors R56 and R57. The series combination of C37 and C38 charges through D14, R61, and R60, until D12 turns on. This occurs when the anode voltage of D12 exceeds the gate voltage by approximately 1.0 volt. When D12 conducts, C37 and C38 are discharged to nearly zero volts; then D12 turns off and the cycle repeats. The value of R61 and the setting of R60 determines the amplitude of the waveform.
Diode D14 provides a small incremental voltage above ground to overcome the forward base-emitter drop of Q14; D13 provides temperature compensation for the output stage. Resistor R96 provides a constant oscillator load for variations in input impedance of Q14. Transistor Q14 is an emitter-follower used to transform the high impedance drive sawtooth to a low impedance drive for Q15.
The vertical choke L5 acts as a current source during linear scan time and provides a high-voltage pulse to aid retrace when Q15 shuts off. To limit this pulse to a safe value, a varistor, R66, is connected across the choke.
Since the impedance of the choke decreases when the collector current of Q15 increases, severe vertical non-linearity will result unless some compensation is employed.
Resistors R64 and R62 couple the emitter voltage of Q15 to the junction of C37 and C38. This path is resistive, and the waveform coupled back will be integrated by C38, This results in a pre-distortion of the drive sawtooth. This is done to compensate for the non-linear charging of C37, C38 and the changing impedance of C5. An additional feedback path through R63 and C39 serves to optimize the drive waveshape for best linearity. Capacitor C40 couples the signal tothe vertical yoke winding and blocks DC.
Spot Kill (See Figure 6-11) The spot kill circuitry is used to reduce the effect of the electron beam concentrating on one area of the CRT after the monitor is turned off. The circuitry is accomplished by raising the arm of potentiometer R73 to the +150 volt level and, therefore, increasing the brightness to maximum to dissipate the highvoltage charge that normally remains in the CRT.
When the monitor is operating, transistor Q20 is on and its collector is near zero volts. Capacitor C44 charges through the base-emitter junction of Q20 and R97. Resistor R72 provides the base bias voltage required to keep Q20 on. When the monitor is turned R73 BRIGHTNESS
TO R77 CRT, PIN2
Figure 6-11 Motorola Monitor Spot Killer Circuit
off, the falling +73 volts is coupled to the base of Q20 to turn off the transistor causing its collector voltage to rise to approximately +150 volts. Diode D24 prevents the negative voltage swing at the base of Q20 from exceeding the reverse voltage rating of the transistor.
Blanking Amplifier (see Figure 6-12) The blanking amplifier combines both the vertical and horizontal retrace pulses to turn off the electron beam in the CRT once every horizontal line and once every vertical field. Capacitor C41 couples the vertical retrace pulses and capacitor C31 couples the horizontal retrace pulses to the blanking amplifier. Resistor R68 determines the amplitude of the vertical pulses, while R69 determines the amplitude of the horizontal pulses. Capacitor C42 bypasses R69 to couple the leading and trailing edges of the horizontal retrace pulses to the amplifier. Resistor R70 allows C41 to discharge when the retrace pulses swing below zero volts. Diode D15 prevents the retrace overshoot from exceeding the reverse voltage rating of Q20. Resistor R71 permits Q20 to turn off between retrace pulses, while R75 and R76 provide the collector voltage for Q20. Capacitor C43 couples the blanking pulses to the control grid of the CRT.
or Figure 6-12 Motorola Monitor Blanking Amplifier Circuit
Avalanche 6-11
AG (conTaasr) u (HORIZ. OSC.) R73 12 Raz (BRIGHT) (Focus) 12
Figure 6-13 Motorola Monitor Chassis Rear View —Component Location
6-12 Avalanche
room ro Lane vent, YOKE uncer Lean)
a err Lexa!
Avalanche 6-13 Figure 6-14 Motorola Monitor Circuit Board Detail—Solder View
POWER SUPPLY
Figure 6-15 Motorola Monitor Schematic Diagram
6-14 Avalanche
CO —
R64 R60 VERT. VERT. Di2 O13 LIN.| size p23 O18 1C1
D208 | a19 \Ra4
bn bitea z Es 16 ,./,020 Q6 Ti Q7 R73 as
024 BRIGHT
SHOWN) SHOWN)
pa ~~ (NOT PI gi P5 CONTRAST
Avalanche 6-15 jit Board §Detail—Component Location Figure 6-16 Motorola Monitor Circui
Table 6-2 Motorola Replacement Part Numbers
| REF. | PART | REF. | PART | |||
| NO. | NUMBER | | | DESCRIPTION | NO. | NUMBER | DESCRIPTION |
| Capacitors: | C31 | 8510191B98 | —.01, 10%, 250V;; Poly. | |||
| All values are in Microfarads unless otherwise noted. | C32 | 23S10255B73 | 20/200, 400/125, 600/100, | |||
| C1 | 23810255A27 | 47, 50V; Lytic | 200/50; Lytic | |||
| C2 | 218135660 | -05, + 80-20, Z5V, 50V; | C33 | 8S10191A51 | -033, 10%, 160V; Poly. | |
| Cer. Disc. | €34,C35 | 8S10191A32_—.047, 10%, 250V; Poly. | ||||
| C3,C4 | 235187A26 | 22, 25V; Lytic | C36 | 21S180E60 | .01, +80-20, Z5V, 50V; | |
| C5 | 21S180E60 | .01, +80-20; Z5V, 50V; | Cer. Disc. | |||
| Cer. Disc. | C37, 38,39 8S10191B67 | 0.22, 10%, 250V; Poly. | ||||
| C6 | 218135660 | .05, +80-20, Z5V, 50V; | C40 | 23S10255A60 —_ 100, 63V; Lytic | ||
| Cer. Disc. | ca | 8S10212B16 | 0,1, 20%, 400V; Mtlz. | |||
| C7 | 218131625 | 330pf, 10%, XSF, 500V; | Poly. | |||
| Cer. Disc. | C42 | 21$180C82 | 0.33, 10%, N150, 500V; | |||
| ce | 21S180B87 | 220pf, 10%, XSF, 500V; | Cer. Disc. | |||
| Cer. Disc. | C43 | 8510191867 | (0.22, 10%, 250V; Poly. | |||
| co | 8S10191B99 | 015, 10%, 250V; Poly. | C44 | 23510255B28 | 4.7, 100V; Lytic | |
| C10 | 8510212818 | 0.22, 10%, 400V; | C45 | 8510191B90 | —-.033, 10%, 250V; Poly. | |
| Milz. Poly. | C46 | 218132492 | .01, +80-20, Z5V, 100V; | |||
| cu | 218131625 | 330pf, 10%, XSF, 500V; | Cer. Disc. | |||
| Cer. Disc. | C47 | 23810255B63 | 100, 10V; Lytic | |||
| c12 | 218180C41 | .0027, 10%, Z5F, 500V; | C48 | 21S180D56 | 47pf, 10%, N750, 100V; |
Cer. Disc. Cer, Disc.
| C13 | 21S180C02 | 10pf, 10%, N150, 500V; | 49 | 21S180B51 | .001, 10%, X5F, 500V; |
Cer. Disc. Cer. Disc.
| c14 | 218180034 | .005, 20%, Z5F, 1KV; | . |
Cer. Disc. Diodes:
| C15 | 23S10229A32 | 1.0, 16V; Lytic | D1 | 48S10813A03 | Diode, Silicon, Zener; |
| C17 | 8S10191B90 | —-.033, 10%, 250V; Poly. | 1N5242 | ||
| c18 | 8510299B28 | 01, 10%, 100V; Polycarb. | D2 | 48D67120A13_ | Diode; A13 | |
| c19 | 8S10299B29 | .0082, 10%, 100V; | D3 | 48S10813A01_ _— Diode, Silicon, Zener; |
Polycarb. IN5234B
| C20 | 8510191B98 | .01, 10%, 250V; Poly. | D4 | 485191A02 | Rectifier, Silicon; 91A02 |
| C21 | 21$180B51 | .001, 10%, X5F, 500V; | D5,D6 = 48D67120A11 | Diode; A11 | |
| Cer. Disc. | D7 | 485134921 | Diode, Damper; D1D | ||
| C22 | 8S10191B98 | -01, 10%, 250V; Poly. | D8 | 485134978 | Diode, Pulse Lim; D1K |
| C23 | 23S10255B50 | 150, 10V; Lytic | D10 | 48S191A05 | Rectifier, Silicon; 91A05 |
| C24 | 21S180B51 | .001, 10%, X5F, 500V; | DW | 488137114 | Rectifier, H.V., D2Y |
| Cer. Disc. | D12 | 485137638 | Vert. Osc.; MPU6027 | ||
| C25 | 8S10299B27 | 0.82, 10%, 200V; Mtlz. | D13,D14 | —48S191A05 | Rectifier, Silicon; 91A05 |
| Polycarb. | D15 | 48D67120A11_ | Diode; A11 | ||
| oe | alae | oS ci ta | bre. Dio’ 485191005 | Rectifier, Silicon; 9105 | |
| C27 | 8510212A11 | 1.0, 10%, 630V; Mtlz. | D20 | 48S10813A02 | Diode, Silicon, Zener; |
Poly. 1N5231B
| C28 | 8510571A06 | .01, 5%, 1200V; | D21 | 48S10813A03 | Diode, Silicon, Zener; |
Polyprop. Foil 1N5242
| 29 | 8510212853 | 0.47, 10%, 630V; Mtlz. | D22 | 48D67120A11_ | Diode; A11 |
| Poly. | D23,D24 | 48S191A05. | Rectifier, Silicon; 91A05 |
6-16 Avalanche
Table 6-2 Motorola Replacement Part Numbers
Ree Part No. Description es Part No. Description
| Fuses: | R60 | 48D25245A29 | Vert. Size; 250K | ||
| FI,F2 | 655138269 | Fuse, 0.8A-250V | Rod | 18D25245A31 | Vert. Lin.; 100K |
| R66 | 6S$10201A04 | Varistor, 1 ma, 120V, 0.5 | |||
| Integrated Circuits: | R73. | 18D25245A28 | Control, Brightness; 200K | ||
| IC1 | 51$10732A01 | Ref. Ampl.; T3F | R84 | 175135589 | 150, 10%, 1OW |
| R93 | 18D25245A21 | Control, +73V out Adj.; |
Coils/Chokes: 2.5K
| 1 | 24C25448A01 — Coil, Horiz. Osc. | ROS | 10731A03 | 1.5K, 10%, 5W |
12 24D25603A09 — Coil, Horiz. Width
| B | 24D25248A14_— | Coil, Horiz. Lin. | Switches: | ||
| \4 | 24D25261A09 | Coil, Def. (M5000-155, | swi | 40510624407 | Switch, Slide; D.P. D.T. |
M5010-155)
| L4 | 24D25261A10 | Coil, Defl. (7000-155, | Transformers: | ||
| M7010-155) | " | 25D25221A05 | —_Horiz.Driver | ||
| 5 | 25D25221C12_ | Choke, Vertical | 2 | 24D25240B23 | HV. Transformer |
| 3 | 25D25239B20 | Transformer, Power |
Transistors: (M5010-155, M7010-155)
| Qi | 488137171 | Emitter Follower; A6H | TB | 25D25239B30 | Transformer, Power |
| Q2 | 488137172 | Video Pre-Ampl.; A6} | (M5000-155, M7000-155) | ||
| Q3 | 488137127 | Video Pre-Ampl.; P2S | |||
| Q4 | 485134952 | Video Driver; A2J | Misc. Electrical Parts: | ||
| Q | 485137476 | Video Output; BIE | v1 | 96S241A01 | 19”-CRT; Type 19VARP4 |
| Q6 | 485137172 | Horiz. Osc.; A6) | (M5000/M5010) | ||
| Q7 | 488137127 | Horiz. Pulse Shaper; P2S | VI | 96S10848A01 | 23”-CRT; Type |
| Q8 | 488137093 | Horiz. Driver; A5F | M22VATP4 (M7000/ | ||
| Q9 | 488137570 | Horiz. Output; B2L | M7010) | ||
| Q10 | 488137173 | Sync Separator; P2W | |||
| Qi | 488137172 | Sync Ampl.; A6) | Mechanical Parts: | ||
| Qi2 | 485137172 | Vert. Sync Integrator; A6) | 9B25456A01 | Block, Fuse (F1, 2) | |
| Q13 | 488137172 | Vert. Sync Ampl.; A6J | 42D25158C01 | Clamp, Defl. Coil | |
| Q14 | 485137639 | Vert. Driver; MPS A13 | 26810251A08 —_ Heat Sink (Q5) | ||
| Qs | 485137596 | Vert. Output; B2V | PI | 15$10183A69 — Housing, Connector; | |
| Q16 | 488137172 | Blanking Ampl.; A6) | Femaie (12-Contact, | ||
| QI7 | 485137368 | Regulator; ASW. | Less Contacts) | ||
| Q18 | 485134952 | Reg. Driver; A2J | 39510184467 | Contact, Plug; 5 Req’d | |
| Q19 | 488137476 | Reg. Buffer; BIE | M5000/M7000, 9 Req'd; | ||
| Q20 | 485137476 | Spot Kill; BIE | M5010/M7010 | ||
| P2 | 15810183A82 | Housing, Connector; |
Resistors/Controls: Male (3-Contact, Less
| the description when ordering standard values of | P2 | 15510183A81 | Housing, Connector; |
fixed resistors up to 2 watts. Female (3-Contact, Less
| R6 | 18D25245A27 | Control, Contrast; 500 | Contacts), M5010/M7010 | ||
| R14 | 178135204 | 100, 10%, 5W | 39S10184A67 | Contact, Plug; 3 Req'd | |
| R17 | 17810731A01 | 3.9K, 5%, 5W | for P2 | ||
| R36 | 7S10130B07 | 1.5K, 10%, 3W | P3 | 28510586A35 | Header, Connector; |
| R42 | 18D25218A14 | Control, Focus; 2M | 2-Contact |
Avalanche 6-17
Table 6-2 Motorola Replacement Part Numbers
REF. PART | REF. PART NO. NUMBER DESCRIPTION NO. NUMBER | DESCRIPTION |
| P4, PS | 15$10183B12 | Housing, Connector; | 14B25459A01 _ Insulator, Fuse Cover |
Female (3-Contact, Less (F1, 2)
| Contacts) M5010/ | 14A562353 | insulator, Mica (Q9, |
M7010 Q15, Q17)
| 39S10184A84 = Contact, Plug; 3 ea. | 14C25230A01__ | Insulator, Molded (On |
Req'd for P5, M5010/ D11 Body)
| M7010 | 14S10157A30 | Insulator, Nylon (2- | |
| $2 | 15$10183A81 | Housing, Connector; | Req’d.); Mtg. P.C. Board |
| Female (3-Contact, Less | 14S10550A02 | Insulator, Transistor |
Contacts), M5000/M7000 Cover (Q9, Q15, Q17)
| $2 | 15S10183A82 | Housing, Connector; | 3136050 | Screw, Tpg; 6-20x%2 CLU |
Male (3-Contact, Less Pan (Mtg. Q9, Q15, Q17 Contacts), M5010/M7010 and D11 Socket)
| 39S10184A64 = Contact, Receptacle; | 9D25470A01 | Socket, CRT; Incl’s. |
3 Req'd. for $2 R77, R78, R79, R80
| $3 | 15S10183A94 | Housing, Connector; | 9D25201A01 | Socket, H.V. and CRT |
Female (2-Contact, Less Anode
Contacts) 9C63825A03 Socket, Power Transistor
| 39S10184A72 | Contact, Receptacle; | Q9, Q15, Q17) |
| 3 Req'd. for $3 | 41D65987A01_— | Spring Special; CRT |
Aquadag Gnd.
6-18 Avalanche
A. GENERAL
TM-600 and TM-623 is a television monitor for video games. It is designed for operation either from a power supply of 115 volts/50-60 Hz AC or 230 volts/ 50-60 Hz AC. The complete monitor incorporates a picture tube, an integrated circuit, 20 silicon transistors, 18 silicon diodes, 2 germanium diodes, anda high-voltage selenium diode.
This model is equipped with 5V/3A power supply for the operation of the TTL control board and operation of double-pulse-type AFC circuit to obtain a stable picture.
B. SPECIFICATIONS Power Supply Input 115 volts/230 volts 50-60 Hz +10%
Power Consumption 60 watts
Video input 0.5 volts composite P/P for 100 volts 2.5 volts P/P maximum Sync negative at input TEC VIDEOELECTRONICS INC. SERVICE MANUAL
Picture Tube 19" (500 mm), 114° deflection for Model TM-600 23" (584.2 mm), 114° deflection for Model TM-623 Integral implosion protection
High Voltage 18 KV nominal at 0 microamperes beam current
Horizontal Retrace Time 12 microseconds maximum
Resolution 500 lines minimum at picture center
Scanning Frequency Horizontal:15.750 Hz +500 Hz Vertical: 50-60 Hz
Tone Burst Amplifier 5 watts peak output with TTL drive at nominal line, fully adjustable. 4 watts peak output at low line.
Environment Operation: Maximum ambient temperature 50°C (122°F) Storage: Temperature range from —40°€ to +65°C
Model TM-600 and TM-623 Monitors
TEC Videoelectronics Inc. (TVI) 3010 Scott Boulevard Avalanche Santa Clara, CA 95050 6-19
geruecrion 2 one eum HORIZ, LIN
hv RECT.
HV TRANS.
Bt 9.5 AMP. ‘CONNECTOR
Figure 6-17 TEC Monitor Chassis, Rear View
‘a0 cso 7 conpensen = SVREGULATOR A441 9, con REGULATOR CONDENSER .
ee
VERT. OUT TRANSISTOR
——— as0s VERT. OUT TRANSISTOR
VERT. LIN.
‘cont, VERT. HEIGHT POWER TRANS. weet \ RESISTOR BRIGHT ‘VERT. HOLD.
6-20 Figure 6-18 TEC Monitor Chassis, Top View
Avalanche
viDEo OUTPUT F
Beapy
veRT. BALANCE
CONTRAST HoRIZ. osc. colt Honiz. OUTPUT
Figure 6-19 TEC Monitor Printed Circuit Board, Top View
Table 6-3 TEC Monitor Replacement Parts Numbers HORIZ. DRIVER TRANS.
HV RECT
HV TRANS,
wioTk con
f sti Ref. .
| c | Part No. | Description | No, | PartNo. | Description | |
| Electrical Parts: | Q303 | 5300500201 | MPS9700U_— | Vert Amp | ||
| PCB1 | 2215303600 = Main PCB | or MPS834) | ||||
| A801 | 485TM60003 | «CRT PCB | Q304 | 4310400030 | 2SC1106 | Vert Output |
305 or 2N6307
| Transistor and IC: | Q400 | 5310500202 | = MPS9700T | Phase Inv |
| Q200 | 5310500202 | MPS9700T | 1st Video Amp. | or MPS834, |
| or MPS834 | Qaoi | 5310500202 | MPS9700T | —Horiz Osc |
| Q201 | 5310500261 | MPS9750T | 2nd Video Amp | or MPS834 |
| or MPS4356 | Q402 | 5310500410 = -2N6558. = Horiz Amp | ||
| Q202 | 5310500410 | 2N6558. | Video Output | or MJE9742 |
or MPSU-10 or 2N4354
| Q301 | 5310500261 | MPS9750T | Sync Separator | Q403 | 5310400040 = -2SC1875—Horiz Output |
or MPS4356. or MJ205
| Q302 | 5310500201 | MPS9700U | Vert Osc | *Q901 | 5310400030 | 28C1106 | Power Regulator |
or MPS834 or MJ3430.
Avalanche 6-21
Table 6-3 TEC Monitor Replacement Parts Numbers
Ref. ttt . eee
No, PartNo. Description a Part No. Description
| Q902 5310500410 | «26558. | Regulator Amp | 1 | N-506BX Horiz O |
ori
| Q903 5310500280 | LM1796_~—sReference Amp | = | zene | |||
| or MPS-D01 | * 1403 | 589517017 | TFB-1006AS. F.B.T. | |||
| Q904 5310500450 | = Mj2955_ | «SV Regulator | * 7901 | 589519021 | TPW-600 | Power Trans |
CRT and Diode: Resistors
| * Vgo1 | 5380000060 | 500SB4 | CRT | R201 | RD-4L471) | 470 ohm) %& W |
| D203 | 5340200280 | MR9712 | Silicon Diode | R202 | RD-AL223) | 22 Kohm J % W |
| or IN4004——L. V., Rectifier | R203 | RD-4L563) | 56 K ohm J % W | |||
| D204 5340200430 = IN4148__ | Silicon Diode | R204 | RD-AL474) | 470 ohm) % W | ||
| or IN4002. | Blanking Clip | R205 | RD-4L332) | 3.3K ohm) % W | ||
| D205 | 5340200430 | —-IN4148. | Silicon Diode | R206 | RD-21823) | 82 KohmJ %&W |
| or IN4002 | Blanking Clip | 07 | RDALS6O) | 56 | ohn) %W |
m
| D206 | 5340200430 | -—«IN4148._—sSilicon Diode | ° | * | ||
| ‘or IN4002 | Blanking Clip | R208 = RD-41102) | 1K ohm | % W | |||
| D207 | 534020280 | MR9712—.200V Rect | R210 | RS-029562) | 5.6 K ohm J 2W | |
| or IN4004 | R215 | RD-42101) | 1K ohm J %W | |||
| D301 | 5340200260 | MR-9701 | Rectifier Silicon | * R216 | RD-4L101] | 400 ohm) % W |
| Diode | * R217 | RD-4L470) | 47 | ohm) %W | ||
| 401 | 5340100040 | AA143 | Phase Det | R218 | RD-41223) | 22 KohmJ %W |
| D402 | 5340100040 «= AA 143 | Phase Det | R219 | RD-ALS63) | 56 K ohm J ve W | |
| D403. | 5340200300 = MR9722.-~—Ss | Damper | 220 | RD-4L102) | 1K ohms %W |
7 "
| D404 | 5340400120 ©‘ TV20-2K80J_H.V. Rectifier | Rox | RD-4L102) | 1K ohm} %W | ||
| or HS30b | R222 | RD-2L102 | 1K ohm) | %W | ||
| D801 | 5340200290 | MR9713.——«400V Rectifier | woos | eDoutos | tk on | ” Ww |
. ohm
| D901 | 5340200270 | = MR9704._—séRectifier | |||
| or 1N4005 | Silicon Diode | R224 | RD-2L122) | 1.2K ohm) % W | |
| D902 | 5340200270 | -MR9704_—_—sRectfier | * R226 | RSOTPION) | 100 ohm) 1W |
| or IN4005 | Silicon Diode | R227 | RD-21123) | 12K ohmJ % W | |
| D903 | 5340200270 | = MR9704_—sRectifier | R228 | RD-21.105) | 1.5K ohm) %2W |
| or 1N4005 _ Silicon Diode | R229 | RD4M681) | «680 ohm % W | ||
| D904 | 5340200270 | MR9704_—_—Rectifier |
a Vs
| or IN4005 | Silicon Diode | tome | a ae | ae onm J ‘ Mm | ||
| D906 | 5340300220 | ~—«INS858A_—Zener Diode | etd | mmionme) Ye | ||
| or 5340300310 | N6002A | R304 | RD-4M102) | 1K ohm) % W | ||
| D907 | R308 | RD-4M104) | 100 KohmJ % W | |||
| Des | 5340200690 | MDA970-1__ | Rectifier | R309 | RD-AMISST | —1.5Mohm) %W |
| Ds10. | R310 | RD-4M332) | «3.3 | Kohm J % W | ||
| , | R311 | RD-4MS563) | 56 K ohm J % W | |||
| Coils and Trans: | amy | Ww | ||||
| *L40t | 589515015 | TDY1005 | —_D.Y. Coil | R312 | RD-4L182 | LaKabm J % |
| L402 | 589512015 | HCH1005 — Horiz Choke | R313 | RD-4L153} | 5K ohmJ % W | |
| Coil | R314. | RD-4L183} | 18K ohm) % W | |||
| 1403 | 589512012 | HC2-035 | Choke Coil | R315 | RD-41203) | 20 K ohm J % W |
| L404 | 589512012 | HC2-035 | Choke Coil | R316 | RS-2P333) | 33 K ohm J % W |
| L405 | 589514013 | AZ-9177DM Width Coil | R327 | RD-4L104J | 100 K ohm | ¥4 W | |
| 1406 | 589514016 | LH-15)54—_ | Lin Coil | R320 | RD-AL124) | 120K ohm J % W |
6-22 Avalanche
Table 6-3 TEC Monitor Replacement Parts Numbers
[ tet Part No. Description A Part No. Description
| R322 | RD-4L224) | 220 Kohm) % W | R904 | RD-2L123) | 12K ohm J % W | |
| R323 | RD-4L433) | 43K ohm J % W | R905 | RD-21223) | 22K ohm J % W | |
| R324 | RD-4L471) | 470 ohm) %W | R906 | RD-2L563} | 56K ohm J % W | |
| R326 = RD-4L152] | 1.5K ohmJ % W | R907 | RD-21563) | 56K ohm} %W | ||
| R339 | RD-4L101) | 100 ohm} %W | R909 | RD-2L682) | 6.8K ohm J 4 W | |
| R331 | RD-4M331f. | 330. ohm % W | ||||
| R332 | RD-4L102) | 1Kohm) %W | Controls: | |||
| RIM | RD-21163 | one | R321 | 5531240088 | —-220Kohm Vert, Height | |
| R936 | RD-AL221 | ene | R327 553472008B | 4.7K ohm Vert. Linearity | ||
| tes | isorz2e01 | 2 ohn aw | R335 | 5531020078 | 1Kohm_ Vert. Balance | |
| RSSB | (RS2P1504 | 15, ohms) | W | R427 | 553303005B | 30K ohm Horiz Hold |
| ee) | eet | 2 tun eM | R603 | 553254005B | 250K ohm__Bright | |
| Se | 2 nds | R805 | 5532050058 | 2Mohm Focus | ||
| fn | ea | ee opal | R908 | 5534720078 = 4.7 Kohm_ B+ADJ | ||
| R402 | RD-4L821j | 820 ohmJ %W | ||||
| R403 | RD-4M561). | «560. ohm] % W | Capacitors: | |||
| R404. | RD-4M103) | 10K ohm J % W | C201 | CE2G1C470. | 47 mF | 16V |
| R405 | RD-4M103) | 10 K ohm | % W | C202 CE2GIFIO1, = 100 mF_— | sv | ||
| R406 | RD-4L272) | 2.7 K ohm J % W | C203 CE2G1C220 | 2 mF | 16V | |
| R407 | RD-4L681) | 680 ohm] % W | C204. CE2G1H101 | 100 mF | 35V | |
| R408 | RS02P682) | 4.7 K ohm J % W | C205 | CE2G1C220 | 2 mF | 16V |
| R419 | RD-41.270) | 27 ohm) %W | C206 CISLIHS61K | 560 pFK | —-50V | |
| R410 | RD-4L182) | 1.8K ohm) “WwW | 207 | CE2GO)221. | 220 mF_— | «63 |
| RAT | RD-4L151) | 150 ohm] % W | €208 5270322401 | 0.22 mF | M_400V | |
| R412 | RD-4L561) | 560 ohm) % W | C209. CE2G2F229 | 2.2 mF | 315V | |
| R413 | RSO1P682) | 6.8 Kohm| 1W | C210 CE2G1H220 | 22 mF | 35V | |
| R414. | RD-2L221) | 220 ohm) % W | C211 | CE2G1H339 | 3.3 mF | SOV |
| R415 | 5160122903 = 2.2, ohm! 1 W | C213. | CKIF2H102K | 0.001 mF_—-S00V. | ||
| R416 | RD-21569) | 5.6 ohmj %W | 220 CE2G2F2200«2.2mF | ~—-250V | ||
| {R417 | RSO2P182) | 1.8K ohm] 2W | C301 | CQIM1H473K 0.047 mF K 50V | ||
| R418 | RSO1P123) | 12K ohm J 1W | 304 CKIBIH391K | 470 pFK | —50V | |
| *R420 | RXO5P220) | 22 ohm| 5W | C305 | CE2G1H478. | 0.47 mF | SOV. |
| *R421—- | RD-21569 | 5.6 ohmj %W | €306 56405333, | 0.033 mF K 50V | ||
| R422 | RD-4L153) | 47 ohmJ 1W | 307 CQIMIHS62K | 0.0056 mF K 50V | ||
| R425 | RD-4L153} | 15K ohmJ %W | 308 CQIM1H273K 0.027 mF K SOV | |||
| R426 | 55337153 | 15 K ohm} %W | C309 | CQIMIH123K | 0.012 mMEK 50 | |
| R802) | RD-2L1545 | 150K ohm J ¥% W | C311 | CQIMIH124K) | 0.42 mF KK | 50V. |
| R80 | RD-2L474) | 470 K ohm J % W | C312 | CQIMIH3%2K 0.0039 mF K SOV | ||
| R811 | RD-21561) | 2MQJ 2 W | 313 DSSD1C229M | 2.2mF | 16 | |
| *R901 | —_RX20P251) | 250 ohm) 20W | C314 | CQIMIH474) | 0.47 mF | SOV |
| R902) | RD-21.101) | 1Kohmj) %W | C315. CQIM1H333K 0.033 mF K_50V | |||
| [ R903 | RD-2L123) | 12 Kohm) % W | | | C316 = CF2GiA470 | 47 mF | 10V |
Avalanche 6-23
Table 6-3 TEC Monitor Replacement Parts Numbers
[Ret Part No. Description Re Part No. Description
| C317 | CE2G2A101 | «100 mF | 100V. | Fuses: | |
| 318 | CKTE2H103K | 0.01 mF_——-500V | *F902 | 6990620011250 2 Amp. | |
| 3195270310301 | 0.01mF | —-630V | *F903 | 5990610013. | -250V 0.5 Amp. |
| C401 | CQIMIH103K | (0.01 mFK = 50V | F904 | 5990630010 | 30V 5 Amp. |
| 402. | CQIM1H103K | 0.01 mF K—50V | |||
| C403. | CQIM1H393K | 0.039 mF K_ 50V | oie hanical Par | M | |
| aod | ckaBoHIS1 | 150 me | soo | 7 | ate-N-Lock Connector (AMP) |
60085005 Edge Collector (Molex)
| CA | GEG 1339 | 3.mr | yi | S-A3915 | Transistor Socket (SMK) | |
| 406 | CQIMIH104K | 0.1 mF K | —50V | *TM60085001 | Fuse Holder | |
| C407 | CQIM1H223K | 0.022 mF J 50V | or *TM60085001 | Fuse Holder | ||
| C408 | CQIM1H683K = 0.068 mF} 50 V | KO0S | —1-380826-0 | Stand-Off Fastener (AMP) | ||
| C409 | CE2G1F470 | 47 mF | 25V | P401 | —PE19-1569 | 4P Plug Assy. (Yoke Line) |
| C410 | CK1B2H681K | 680 pFK | —_500V | P402PE19-1570 | 4F Recep Assy (Yoke Line) | |
| C411 | CK1B2H222K | 0.0022 mF K 500V | P4o3.-PEI9-1571 | 3P Connector Assy. (Video | ||
| C412 | CKIBIH152K | 0.0015 mF K 50V | Input) | |||
| C413) | CK1B1H102K | 0.001 mF K 50V | A621 | PE19-1572 | 4P Connector Assy. | |
| *C414 | CKIB3D471K_ | 470 pFK | KV | (Q901 Line) | ||
| C415 | CQIM2AI04K | 0.1 mF K | 100 | A631 | PE19-1573 | 6P Connector Assy. |
| *C416 | 5270333201 | 0.0033 mF | 1.5KV | (Q304/Q305 Line) | ||
| Cay | CE2G2C100 | «10 mF | tov | P406PE19-1574 | 2P Plug Assy. (Heater Line) | |
| cae | 5270333401 | 0.33 mF K | 200v | P407— | PEI9-1575 | 2P Recep Assy. (Heater Line) |
TE901 PE19-1576 Terminator, 6 Pin
| Cat) | 2685101 | 1G mF | 35V | E001 | 135431015 | Ground Plate |
| C420 | 56625471 | 470mF | 25V | rool | ‘2a-iea001 | Frame |
| Ce01 | 5270356302 = 056 MEK 630V | H003 | 5432001-1 | Plate Heat Sink A | ||
| *c901 | 5240700400 | 450 mF | 200 | Q493D 54320017 | Plate Heat Sink C | |
| c902 | 100 mF | 160 V | ||||
| 904 | F2G2C229 | 2.2 mF | 160V | |||
| C905 | CKIF2H102K | «0.001 mF_~—500V | ||||
| 911 | 56625105 | 10000 mF | 25 | |||
| C912 | 56616018 | Time | 16V |
| 7802 ) 599030001 | EGP-H751A | MEE TE |
za03 2. J—Indicates + 5% tolerance K—Indicates +10% tolerance Switches: M—indicates +20% tolerance
| *SW-1, | PE13-1567 | 115V/230V Power Line |
Slide Switch
6-24 Avalanche
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
v Pig PI 10 PI-7 IN eur
eves | ‘TPW-600
TR, IC, and Connector Lines
LMI736 MPS 9417 INSHBGA MPS Loe a 1 WES. $24, mes s750MPS 9700 1NeO02A i—
ace ECs MsES20 MaEIO8 mc 7eosce = NJESTA2
su298s 2sci 108 2s 1875
626 Avalanche 2200 pga700T
ee Risa ae o ek |
NOTES -
- Unless otherwise specified, all resistance values 4. All waveforms are measured with strong signal are in ohms. input and contrast set to give normal picture.
- Unless otherwise specified, inthe schematic dia- 5. This schematic diagram covers basic or repregram all capacitor values less than 1 are expressed sentative chassis only. There may be some differin mfd, and values more than 1 are in pfd. ences between actual components on chassis and
- Voltage readings are taken with VTVM from point the schematic diagram. indicated on chassis to ground.
Figure 6-20 TEC Monitor Schematic Diagram
Avalanche 6-27
6-28 Avalanche
oa#ooMmo re O ©3029 He c90t [eo 0901-904 e
R901
c ime Fes)
BOTTOM VIEW
Figure 6-21 TEC Monitor Wiring Diagram
Avalanche 6-29
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
TM-096 1st Printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A. If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name Firm Q Distributor O Operator
Address O Other City State Zip
First Fold
Atari, Inc. P.O. Box 9027 Sunnyvale, California 94086
Attn.: Publications Group, Coin-Op Engineering
Second Fold
a6p7 siyy adey First Class Permit #1004 Sunnyvale, CA
980%6 VO ‘aleakuuns 1206 X08 ‘O'd “oul ‘Wery an
Cut along this line
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation Or improper testing.
In no event shail Seller be liable for loss of profits, loss of use, incidental or consequential damages.
EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may noi be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
) K ATARI INC ® 1265 BORREGAS AVENUE ®
ATARI PO. BOX 9027
SUNNYVALE, CALIFORNIA 94086 408/745-2000 = TELEX 35-7488