CATHODE RAY TOMES

Hustle

Hustle (Gremlin, 1977) · Manual · 41 pages · 22 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

HUSTLE

OPERATING INSTRUCTIONS

AND

SERVICE MANUAL

GREMLIN INDUSTRIES, INC. 8401 Aero Dr. San Diego, CA, 92123 June 30, 1977

Page 3

"HUSTLE"

“TABLE OF CONTENTS

|. GENERAL INFORMATION

Introduction ------------------------ — Page 1

Important Notes--- ---:Page 2 Warranty/Factory Service - --- Page 3 Repackaging ----------- --- Page 4 Repackaging Diagram ----------------- Page 5

~ i.» OPERATION

‘Game Concept ------------------------ Page 6 Operator Options ---------. --- Page 9 Free Game Option Diagram --- ----- Page 11 System Description ---- -— Page 12 System Block Diagram ---------------- Page 14 Character Generation Circuitry Diagram-- Page 15 Tone Generator Diagram -~------------- Page 16

HH. = MAINTENANCE

Factory Assistance/Equipment --------- Page 17 Symptoms/Causes ----~-~--~ — Page 18 Key Waveforms Diagram - - Page 21 Character Code Table --- --- Page 22 Parts List ------------0------------ -- Page 24 Schematics Motorola 19" Service Manual ---------- Page 31

Page 4

JNTRODUCTION

HUSTLE is an electronic game that makes extensive use of digital integrated circuitry and television monitor circuitry, This manual assumes the maintenance technician possesses a general knowledge of solid state circuitry, TTL digital integrated circuitry and T.V. monitor concepts. Any individual NOT knowledgeable in these areas SHOULD NOT attempt repair of the electranic portion of this game. IT SHOULD BE NOTED THAT ANY ATTEMPT TO REPAIR THE GAME IN THE FIELD WITHOUT THE EXPRESS CON- SENT OF THE FACTORY WILL IMMEDIATELY VOID THE WARRANTY!!!

IMPORTANT NOTES:

NEVER

NEVER

DO NOT

ALWAYS

CORRESPONDENCE replace any components with anything other than exact replacement parts. (See Parts List located on Service Schematics.)

remove circuit boards/connections while power is on.

replace the fuse with anything other than the proper value. A blown fuse indicates an overload condition within the game. Replacing the fuse with a higher value can cause severe damage to internal components if an overload occurs.

consult the manual before attempting repairs.

regarding this game should be addressed to:

GREMLIN INDUSTRIES, INC. 8401 Aero Drive

San Diego, California 92123

(714) 277-8700

Page 5
IMPORTANT NOTES

An important service note is posted in the HUSTLE game and is repeated here for

emphasis:

IF AT ANY TIME THE T.V. SCREEN SHOWS A MEANINGLESS DISPLAY OR THE GAME OTHERWISE MALFUNCTIONS, SIMPLY DROP A COIN INTO THE COIN MECHANISM. THIS SHOULD CORRECT THE PROBLEM, IF NOT, THE GAME REQUIRES SERVICE,

The circuitry in HUSTLE has been arranged so that the insertion of a quarter through

the coin mechanism will reset the system. This clears up temporary problems caused

by power line disturbances, static, etc.

SERVICE TECHNICIAN NOTE:

The system reset circuitry described above requires that the coin counter is attached to the system. If there is a coin counter problem and no replacement is available, the game will function properly if a 1OK Ohm resistor is connected across the coin counter pins to the video logic board.

Page 6

WARRANTY

FACTORY SERVICE WARRANTY/FACTORY SERVICE INFORMATION

HUSTLE is under factory warranty (parts and labor) for the following time periods:

All electronic components/connectors for one (1) year except:

  • Transformers - 90 days
  • Fuses/Lamps - No Warranty

The Warranty covers defects/failure under normal use.

Should an assembly become defective, contact your local distributor, Factory authorization to return the assembly will be issued with transportation charges prepaid. If decided upon by factory representative, an advance replacement will be made. No merchandise may be returned to the factory without prior authorization,

The assembly will be repaired and returned, transportation charges prepaid, if still in Warranty and no advance replacement made.

If the assembly is found to be damaged by misuse, improper attempts at repair, or abuse, it will be repaired and returned with transporta~ tion and repair charges billed.

Out of Warranty assemblies, if returned to the factory with transportation charges prepaid, will be repaired and returned with transportation and repair charges billed,

In the instance of a defect of an assembly manufactured by other than GREMLIN INDUSTRIES, INC., every effort will be made to assist the customer in obtaining satisfaction from the original manufacturer.

Page 7

REPACKAGING INSTRUCTIONS

Should it be necessary to ship this game, the following instructions are provided

for game crating.

NOTE: A) If the original shipping bolts (REF 1) have been discarded, obtain four 5/16-18 x 1 3/4 hex head bolts with 5/16

flat washer. Lay game on its side and attach skid (REF 2).

B) Place game upright. Tape game keys to upper flange of

operator's panel (REF 3). Crate the game using appropriate shock-absorbent packing material (REF 4). Include padding on all four corners of the game (REF 5).

C) After crating is completed, secure package with strapping (REF 6).

If the game is to be shipped to GREMLIN INDUSTRIES for service or repair, attach a tag identifiying the distributor and indicate the service or repair to be accomplished; include the full serial number of the game.

Page 8

EPACKAGING INSTRUCTIONS -

Page 9

GAME CONCEPT

HUSTLE

HUSTLE is a one or two player video game which challenges players! reaction time as they attempt to build up a high score, The object of the game is to maneuver a moving arrow into targets which appear randomly on the screen. Each arrow is accompanied by a “tail'', which can be used to block the opponent from scoring targets.

TARGETS - The targets appear randomly on the playfield. The position of a target, the value of a target, the time a target stays on the screen, and the time before a target appears are all unpredictable. There are never more than two targets on the screen at any time.

To add to the unpredictability, some targets appear with a value of "???". These are mystery targets, and can have a value from -900 points to +900 points. Players go after the mystery targets at their own risk since the only way to determine whether or not a mystery target is positive or negative is to hit the target. Whenever a target is scored, the game pauses while the appropriate player's score is tallied. Two distinctive sounds accompany the scoring, depending on whether the target score is positive or negative. All non-mystery targets (which are all positive), and all mystery targets (which have positive values) are scored with an attention-getting "warble" sound. All mystery targets which prove to be negative are scored with a distinctive "penalty" sound.

CRASHES -

A crash (accompanied by a loud boom sound) occurs whenever a player hits anything other than a target. The three obstacles a player might hit are one of the screen boundaries, the other player's tail, or his own tail, Whenever a crash occurs, the opponent scores 400 points PLUS all target values on the screen. If any mystery targets are on the screen during a crash, their values are revealed, and they are awarded to the opponent. All mystery targets whose values are revealed as the result of a crash are scored positive for the opponent.

GAME SPEED -

The game begins with the players moving at a moderate pace,. Every time a target is scored, the pace picks up slightly. After ten targets have been scored without a crash, the pace stays at a maximum rate. Whenever a crash occurs, the pace reverts to its initial moderate value, and increases with each score, as before,

Page 10

GAME CONCEPT (Cont'd.)

TAIL LENGTH -

Whenever a crash occurs, both players’ tails grow longer. The game plays quite differently as it progresses. At the beginning of a game, both players have short tails and are highly maneuverable. At this stage the game is a "foot race" to score the targets. As players crash and tails get longer, a blocking strategy is added to the race for the targets. This constantly changing nature of the game is designed to provide long-lasting appeal, and insure a long earning history,

SINGLE PLAYER -

HUSTLE has been designed to be just as exciting for one player as it is for two. A single player plays against himself, and not against "the computer".

The single player game is initiated by simply pressing the ONE PLAYER START button instead of the TWO PLAYER START button after inserting a coin. The controls for one player are located on the right side of the control panel. The game plays the same as for two players, with these exceptions:

  • There is a single arrow and tail, instead of two.
  • Crashes are scored as PENALTY points, with the same score as in the two player game, That is, a crash scores 400 plus all onscreen targets into the PENALTY score.
  • At the end of the game, the PENALTY points are subtracted from the player's score. The object of the single player game is to rack up as many points as possible. The game action is the same as the two player game, with the lengthening tail and the accelerating pace.

FREE GAMES -

For areas of the country where free games are legal, HUSTLE can be set to award free games for scores of 11,000; 13,000; 15,000 or 17,000 points. The game is shipped with the free game option disabled. If free games are legal in your area, it is highly recommended that you enable them---they provide an extremely powerful incentive to play the game, and thus increase your earnings.

Free games are awarded only in the single player game, since the two player game could give free games any time two players cooperated to give one of the players a very high score.

It is not possible to win two free games in a row (i.e. no free games on free games).

Page 11

GAME CONCEPT Cont'd.)

FREE GAMES - (Cont'd.) Whenever free games are enabled, the message "SCORE XX000 POINTS FOR FREE GAME" appears on the screen just after the ONE PLAYER START button is pressed, The XX will be 11, 13, 15, or 17 depending on how you jumper the game (see OPERATING INSTRUCTIONS). This message is displayed for about 5 seconds, and then the single player game begins. Whenever a free game is won, the message FREE GAME! is momentarily displayed on the screen, followed by the message PRESS START. If at this point ONE PLAYER START is pressed, the free game score message will not be displayed before the game starts, since a second consecutive free game will not be awarded. It is also possible to press the TWO PLAYER START after a free game is awarded and play a two player game.

GAME TIME -

The top margin of the game contains the word TIME, with a two digit timer above it. The game starts with a time value of 90, and decrements to 0, at which time the game is over. The timer actually counts player movesrather than "ticking" once per second. Also, the timer stops during all scoring. These effects produce a repeatable game time of about 2 minutes. It is possible to shorten the game time to about 1-1/2 minutes by changing an internal jumper. In this case, the timer still begins at 90, but it "ticks" faster.

COINS -

HUSTLE is set to play either the one or two player game for a single coin (both games take approximately the: sanie time). An interrial option’allows game play for two coins, three coins or four coins. If this option is enabled, the message "MORE COINS" appears each time a coin is inserted, until the proper number is inserted. At this time, the message "PRESS START" appears. Our location tests indicate that the single coin mode (as shipped) will maximize your income, so no adjustment should be necessary.

ANTI-CHEAT -

HUSTLE contains a feature which will not give game credits if the coin switch is manually depressed, or if the coin door is slammed. In checking out the game, you must actually insert a coin to get things started--flicking the coin switch will not always start the game.

Page 12

OPERATOR OPTIONS

HUSTLE is shipped with the following preset options;

  • FREE GAME option disabled.
  • Game length approximately 2 minutes.
  • One coin per play. If free games are legal in your area, it is highly recommended that the game be set for free games. A single jumper inside the game sets the free game score at 11,000; 13,000; 15,000 or 17,000 points. Our location tests indicate that most games should initially be set at 11,000 or 13,000. It is a good idea to start with 11,000, and after 1-2 weeks, increase to 13,000. Only in high skill areas such as college recreation areas should the free game score be set for 15,000. 17,000 should be used only if the game has been mastered by many people. DO NOT set the free game score too high to start--this will turn off many beginning players. To enable freegame option diagram, follow these instructions:
  • Disconnect power and remove the back from the game.
  • Locate the large printed circuit board (mounted on the horizontal shelf).
  • At the rear of the circuit board is a row of connectors. These connectors are arranged in four groups of ten pins. The right hand connector has no receptacle on it-~only ten pins with a wire jumper. This jumper sets the free game option as shown in the figures in Diagram #2.
Page 13

OPERATOR OPTIONS (Contd.)

  • Remove the jumper from pin 1 and plug it into pin 7, 8, 9, or 10, depending on the desired free game score. To disable free games, place the jumper on pin 1. The game length and number of coins per play are jumpered in a similar manner. For details refer to the cabinet wiring schematic at the rear of the manual. The jumper wires required to activate these options are taped to the appropriate connector harnesses,

Whenever HUSTLE is not being played, an advertisement sequence is initiated. Targets continuously appear and disappear from the screen to attract attention. To avoid patron confusion, the words "Game Over! appear while the advertising is in progress,

E-Z Adjust™™ Control Panel - HUSTLE has one adjustment which is located on

the back of the coin door:

VOLUME CONTROL - Set to desired volume for boom and tones during the game.

Page 14

Diagram #2

FREE GAME OPTION DIAGRAM

FIG.A

098765432 1

098765432 1

FIG.¢

0987654321

098 7654321

1098765432 1 -ll- FREE GAME AT 17,000 POINTS

FREE GAME AT 15,000 POINTS

FREE GAME AT 13,000 POINTS

FREE GAME AT 11,000 POINTS

NO FREE GAMES

Page 15

SYSTEM DESCRIPTION

SEE SYSTEM BLOCK DIAGRAM (Fig. 3)

MICROPROCESSOR -

The game microprocessor is a Model 8080A and it functions as the Central Processing Unit (CPU) in the system, The CPU (1) is synchronized by a clock circuit which provides frequencies required by the CPU and the Video Timing Logic (14),

Address Bus (4) selects the memory addresses to be accessed by the CPU. It is routed to three subsystems:

  • Read Write Memory (6): A random Access Memory (RAM) used to form a first in/last out (stack) memory. Used to perform subroutine calls and returns, also used for temporary data storage during program execution.
  • Read Only Memory (ROM) (7): Stores program instructions for the CPU.
  • Address Multiplexer (8): Selects either CPU addresses or addresses from the Video Timing Logic. Used to address the Video Refresh Memory (9).

Data Bus (5) carries data to and from the CPU. It receives data from Read Write Memory, Read Only Memory, Video Refresh Memory and Input Ports (12). The Bus transmits data to Read Write Memory, Output Ports and Video Refresh Memory. The Input Ports accept player contro] data (19). The Output Port (13) initiates sound control and activates any external logic and indicators needed by the game.

Timing and Control Logic (11) generates synchronizing signals to keep system operation and synchronized to the CPU. It controls:

Memory Read Memory Write Input Port Read Output Port Write BRUNE

Page 16

SYSTEM DESCRIPTION (Cont.d)

The remaining elements in Figure 1 convert CPU system information into a video display format. The T.V. monitor (18) uses a standard 525 scan line system.

Video Refresh Memory (9) stores information from the CPU which is read out as the CRT beam sweeps across the screen. It is addressed from two sources as controlled by Address Multiplexer (8). During vertical sweep retrace of the CRT, the Video Refresh Memory is addressed by the CPU so information can be updated. During scan time, Video Refresh Memory is addressed by Video Timing Logic (14). Refresh Memory Control (10) insures that address demands from Video Timing Logic and the CPU never occur simultaneously.

Character Generator Memory (15) provides a means for Video Refresh Memory to select 64 dots for each 8 word access. Each image, on the display, has the dimensions of 8 dots high, and 8 dots wide. Shift register (16) develops this into a video signal. (See Fig. 2)

A Tone Generator is driven by Output Ports (13), The CPU controls the fre~ quency of the tone by loading a number (0-255) into the Output Ports (13). A direction change by a player will cause the CPU to load a different number into the Output Port, changing the tone. (See Fig. 3) This generator also produces the "warble" sound heard during scoring.

Page 17

Diagram #3

WYSOVIC MOO ld WALSAS

At 280alS INdLNO agOdLS LNdNI 6t M WAN a Waw SYOLVDIGNI SaNnOS STOYLNOD

UL 3901 JOY1NOD ONY ONIWIL AQvad VvO808 43NIGWOD ] = ssz¥aav |

NOILISOd

ONIINY 78 Ww3d 14) Qnv

INAS

ONIWIL OACIA Al

Page 18

-15~ MEMORY INPUT Ds

FROM MICROPROCESSOR

DATA BUS

> 9° re5432 |

CHARACTER GENERATION CIRCUITRY

VIDEO

REFRESH

MEMORY

1024X 8

ADDRESS —- FROM ADDRESS MULTIPLEXER IN JIN TIN] IN | Bele jejele|e le D>/>2>/>l>IlD>/D/>D olo|o o|o|o EIGHT OUTPUTS TO SHIFT REGISTER Diagram #4

Page 19

FROM MICROPROCESSOR

SYSTEM

OUTPUT

STROBE

Dg DI D2 D3 D4 DS D6 D7

Cc «DC

PRESET COUNTER

(-3. 74163) Lp a j b

3.74163) ip Diagram #5

TONE GENERATOR FIG.5

Page 20

FACTORY ASSISTANCE & EQUIPMENT

FACTORY ASSISTANCE:

TECHNICAL HELP IS AVAILABLE FROM THE GREMLIN FACTORY,

IF A PROBLEM OCCURS WHICH CANNOT BE EASILY RESOLVED

BY YOUR DISTRIBUTOR, A PHONE CALL OR LETTER TO THE

FACTORY WILL BRING ATTENTION TO YOUR PROBELM BY A

TRAINED REPRESENTATIVE

NOTE: IF AT ANY TIME THE T.V. SCREEN SHOWS A MEANINGLESS DISPLAY OR THE GAME OTHERWISE MALFUNCTIONS, DROP A COIN IN THE COIN MECHANISM, THIS SHOULD CORRECT THE PROBLEM, IF NOT, THE GAME REQUIRES SERVICE.

EQUIPMENT: The following is a recommended list for anyone attempting to service HUSTLE.

Oscilliscope - 50 mhz or wider band width

DVM (igital Volt Meter)

OHM Meter

Logic Probe

. Solder Station - 75 Watt or less

Jumpers Nou ft WN eH « Replacement parts including game programs:

1024 x 4 proms 316-0016, 316-0017, 316-0018, and 316-0019

Page 21

SYMPTOMS/CAUSES

HUSTLE POWER SUPPLY MALFUNCTIONS:

1... Remove Output Connectors

  • Initial Tests: (GND lead to C-18 negative terminal located off board.)

a. +9vat"+" of C-18

b. +19v at C-6 (4700 mfd)

c. -19v at C-5 (4700 mfd)

d, -12v at pin 11

e, +12vat pin 12

f. +5v at pins 18-20

g. zero v (GND) at pins 14-16

  • If adjustments are required, attach meter ground to pins 14, 15 or 16 or equivalent local ground and:

a. +5v adjust - input lead to pins 18, 19, 20 and adjust R-9 for +5 .0 to +5.1VDC

b. +12v adjust - input lead to pin 12 and adjust R-8 for 11.5 to -12.1VDC

  • — If initial test is good, attach output connectors to Video Logic Board. Repeat Step 2. a. If readings differ from those previously taken, a loading problem exists on the Video Logic Board.

No -12VDC or 5VDC on the Video Logic Board: (Power Supply Normal)

Video Logic Board Schematic (VLBS) (SH. 2), CHECK U-65, C-29 for open/short. CHECK R-40, C-12, D-2 (VLBS) (SH. 1).

No +12VDC at CPU: (Power Supply Normal) (VLBS) (SH. 2), CHECK U-65, C-28, (VLBS) (SH. 1). CHECK C-23, C-25,

Page 22

SYMPTOMS/CAUSES (Cont'd.)

No 01, 22 CLOCKS: (Ref. Fig. 4A)

(VLBS), (SH. 1). CHECK U-32 pins 1 and 3 for 20.79MHZ. CHECK U-31 pins 14, 13, 12 and 11 for 150 nsec sinewave. CHECK U-17 pins 1, 3, 4, and 10. CHECK latch network U-18 and U-8. CHECK high voltage outputs of U-30 pins 3 and 6. If not present, remove driver transistor. Should U-30 now output, replace driver transistor, if still not present replace U-30. U-45 could load down 01 clock.

No Coin Start:

(VLBS) (SH. 1) CHECK output U-9 pin 6. If signal not present, lift U-10 pin 5. Should signal return, replace U-10. If still not present, CHECK output of U-8 pin 3. CHECK D-8 pull up diode and C-18. CHECK U-14. U-32 could be shorting signal to Q, and Q,. 3 4

No Coin Meter Action:

(VLBS) (SH. 1). Signal from U-8 pin 11 feeds current limiter R-27 to Q,. Saturated Q, turns on high current transistor Q.. Either Q, or Q,. faulty, will sane hs 5 4 5 inhibit meter.

No Player Control:

(VLBS) (SH. 1). Input accepted through U-12 and U-13 via data lines when strobe IND2 signal is generated through U-18 from U-45 and U-51 (status latch). CHECK U-18 pin 11, U-45 pin 8, U45 pin 11, U-51 pin 10 for strobe pulse.

No Game Time Select:

(VLBS) (SH. 1). Input accepted through U-11 via data lines when strobe IND 1 signal is generated through U-18 from U-45 and. U-51. CHECK U-18 pin 3, U-45 pin 8, U-45 pin 11, U-51 pin 10 for strobe pulse.

Meaningless Display on Screen: (Inserting coin does not correct problem)

There are two probable areas:

  • A program malfunction -

.a. CHECK PROM sockets, U-2, U-3, U-4 and U-5

Page 23

SYMPTOMS/CAUSES (Cont'd.)

  • A data transfer malfunction -

a. Test the CPU Data Bus by ensuring proper voltage levels. Pullup resistors are used to make memory outputs compatible with the 8080A. High State Logic on the Data Bus should be 3.3v minimum, For involved problems in this area contact GREMLIN INDUSTRIES,

Characters on Screen not correct: (Wrong image behaves normally)

(VLBS) (SH. 2). Use character generator code table to isolate possible bad RAM. (U-37; U-38; U-39; U-40; U-4.1; or U-42). Also-probable-are U-22. U-23 (data buffers), U-24, U-25, U-26 (multiplexers), U-29 and U-43, U-49 (shift register).

No Video: (Ref. Fig. 4B, 4C, 4D)

(VLBS) (SH. 2). CHECK U-54, U-53 circuitry for H reset. U-52 pin 1, clock for horizontal scan, U-55, U-58 provides timing for vertical scan. U-64 develops sync pulses.

Monitor Malfunction:

Refer to Motorola Service Manual (File VP 12). This manual included with HUSTLE schematics.

Audio Tones; Sour/None:

(VLBS) (SH. 2). U-68, U-61, U-62, U-66, U-67, U-60 comprise tone

generator. Amplifier on Power Supply Board (U-4, Q,, Q3, Qs Q,). Could

also be problem area.

Boom; Sour/None:

sheets (SH. 1, SH. 2). D-6, Qo Q9r Qy U-5, Q, Qs Generates

Amplifier section on Power Supply Board (U-4, Q,, Qs, Qe, Q,), also probable. 9

Page 24

I I MIC. WPROCESORi| CLOCKS |

IL5 V g | 5V foc.2 N.S, | | Hea oe 481 NS ————_> I 240.8 NS |

HORIZ H BLANK VERTICAL V BLANK

TIMING

H RESET 330H TIMING V RESET’ 262V FIG.B | FIG. C —___— ‘ 272 4 al zev \ 248 V Hsyve [Lo v SYNC rt

VIDEO OUTPUT

FIG. D

WITH CONNECTOR OFF | | | | Ane 4INVERTED uA

SYNC PULSES

DURING V BLANK

Diagram #6

KEY WAVEFORMS

Page 25

CHARACTER CODE TABLE

I.C. (U#) 40 41 42 37

0 (SPACE) 1

1 ? 1

0 l ver vrcrea HHP PeRebeaEN i

“29 1.C. (U#)

39 40 4Y 42

MA LL

(NOT USED)

js)

NN

= |

oe ote By

Page 26

CHARACTER CODE TABLE

1.C. (U#) 1.C. (U#) 37 38 39 40 41 42 37 38 39 40 41 42

10000048 1.10000 ¢

100001 ¢ 11/0001 1

1000310 € 11004102

1000311 F 1100311 3

10031000 1104100 4 LARGE 10010310 1 1031041 5

100212100 11031410 6

10021121210 110314311 7

101000 6 1 11000 8

1010011 1110041 9

10101028 1110310 S85

1010141 +M 1110311 7T

101100 +N 111100

101101 ~0 1111031 ~°

1014110 ?P 1 1 1 1 1 0 WOT USED) 1011141 -R 11 L 1 1 1 (NOT USED)

Page 27

HUSTLE PARTS LIST

DESCRIPTION

ASSY,

ASSY,

ASSY, COIN COUNTER

CONN, CRIMP LOCK CONN, KEY POLARIZING CONN, FEM 10 PIN COUNTER, DIGITAL

CONTROL BLOCK

CONN, CRIMP COINBOX CONN, CRIMP LOCK CONN, KEY, POLARIZING CONN, SPADE LUG 1/4" SOLDER LUG #10 CONN, FEM 4 PIN BLK CONN, FEM 10 PIN KNOB, VOL CONTROL SWITCH BRACKET

HUS OPER. SWITCH

CONN CRIMP LOCK CONN, KEY, POLARIZING CONN, SPADE LUG 1/4" CONN SPADE LUG #10 SWITCH ASSY WICO CONN, FEM 10 PIN

ASSY, HUS VIDEO LOGIC

ASSY,

ASSY, JUMPER HARNESS

CONN, CRIMP LOCK CONN, KEY, POLARIZING CONN, FEM 10 PIN

JUNCTION BOX

BOX, JUNCTION QTY USED

Be PRREN

ray HP RPNOREPPRP BOD PART NUMBER

807-0011

211-0005 211-0007 211-0016 220-0008

813-0004

211-0001 211-0005 211-0007 211-0019 211-0027 212-0005 212-0016 240-0001 250-0031

813-0002

211-0005 211-0007 211-0019 211-0027 212-0016 510-0023

813-0001

807-0006

211-0005 211-0007 212-0016

807-0009

140-0016

Page 28

HUSTLE PARTS LIST (Cont'd.)

DESCRIPTION QTY USED PART NUMBER

COVER, JUNCTION BOX1140-0017
CONN, QUICK, 1/4" FEM2211-0017
CONN, SPADE LUG 1/4"14211-0019
CONN, QUICK 3/16" FEM4211-0022
BUSHING, STR/RELIEF2280-0007
TERMINAL STRIP 6 POS1280-0011
MARKER, TERM STRIP1280-0017
SWITCH SPDT CHERRY1510-0013
FUSE, 2 AMP 250V SB1514-0001
HOLDER, FUSE1514-0005
CORD, LINE, 3 COND,1600-0001
ASSY, MONITOR HARNESS1807-0005
CONN, CRIMP LOCK2211-0005
CONN, KEY, POLARIZING2211-0007
CONN, SPADE LUG 1/4"3211-0019
CONN, 12 PIN BLOCK1211-0025
CONN, PINCRIMP, FEM5211-0026
CONN, FEM 4 PIN BLK1212-0005
ASSY, POWER INTERRUPT1807-0012
CAP, E, 1M50V2150-0009
CAP, F, .22M100V1152-0002
PCB POWER INTERRUPT1170-0073
CONN, FEM 10 PIN RT/A1212-0017
IC TIMER NE5552314-0001
RES 1K OHM ;/2W 5%7471-0102
RES, 100K 1/2W 5%2471-0104
RES, 33K 1/2W 5%1471-0333
RES, 470K 1/2W 5%1471-0474
DIODE, ZENER 1N52311481-0008
XISTOR 2N44031482-0006
ASSY, POWER SUPPLY1807-0003
ASSY, PWR SUPP/AMP B1807-0002
Page 29

HUSTLE PARTS LIST (Cont'd.)

DESCRIPTION

BUSHING S/REL 3/8" BUTTON, PLUNGER WHITE CABINET, UPRIGHT CASHBOX, UPRIGHT CLIP, SWITCH CLIP, WIRE HOLDDOWN COIN MECHANISM, DUAL CORNER STRIP COVER GRAPHIC PANEL COVER, SPEAKER 6 x9 DECAL, CAUTION 115V DECAL, HUSTLE DECAL, IMPORTANT NOTE DECAL, RE-CYCLE DECAL, S/N DECAL, S/N SMALL DECAL, SERVICE DECAL, TIP N.TELL DRAWINGS, HUSTLE FEET, CABINET FIXT, LAMP FLUOR 18" FRAME, BEZEL GRAPHIC, PANEL OPTR. LAMP, FLUORESCENT, 18" LATCH, LOCK UPRIGHT LID, ASSY, COIN BOX LOCK, PANEL MANUAL, HUSTLE MASK, SHADOW CABINET MOLDING STRIP MOLDING-TRIM, LOWER MONITOR, VIDEO 19 IN MOUNT BKT COIN BOX NUT, WIRE PANEL, DISPLAY UPPER PANEL, GRAPHIC FRONT PANEL, MONITOR SCREEN PANEL, OPERATOR

~26- QTY USED

Ww PREP EPNBPPR BBP RBHEPEPEP EP EPP RP BER RP HHP PNP EB EPEP BPP OPEB PART NUMBER

280-0001 240-0008 140-0014 220-0012 250-0048 280-0004 220-0010 420-0037 253-0030 130-0002 420-0030 420-0067 420-0038 420-0040 420-0028 420-0041 420-0029 420-0060 420-0068 280-0030 390-0012 250-0032 253-0027 390-0011 220-0015 220-0016 220-0009 420-0069 253-0014 250-0038 250-0109 200-0002 252-0014 280-0010 253-0036 253-0034 253-0037 250-0102

Page 30

HUSTLE PARTS LIST (Cont'd.)

DESCRIPTION

PLATE, COIN RETENSION PLATE, LOCK STRIKE SPACER, WICO SWITCH SPEAKER, GAME 6x9 SPRING, RETAINER TRIM, CONTROL PANEL TOP COVER WASHER, ANCHOR WRAPAROUND SIDE QTY USED

BHEENEEPNER PART NUMBER

250-0062 250-0033 253-0031 130-0001 250-0034 250-0106 420-0035 280-0028 420-0034

Page 31

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 32

‘ONS TONE ue = DESCRIPTION APPROVED GREMLIN INOUSTRIES INC. 840! AERO DR. SAN DIEGO,CA. 92123 Pheld SCHEMATIC — POWER INTERRUPT SIZE] CODE IDENT NO. [DRAWING NO.

br | 170-0073 P.C. BOARD 212-0017 CONN FEMALE /OPIN RT ANGLE| Ae 00/4 | TRANSISTOR 2N4401 84493 482-0006 | TRANSISTOR 2N4405 ge 481-0903 DIODE ZENER IN 5231 DI 47/-0474 | RES. 470K OHM 12W 5% | RZ 471-0333 RES. 33K OWM 172W_ 5% | Ro 471-0104 | RES. /00K OHM \/2W 5% | R4,R5 47-0102 RES. 1K OHM 1/2 W 5% | RI-R3,RB-RIO

4. 3/t 752-0002 | CAP. F._.22M 100V Cl Ci 212 150-O00le | 2APE. /M lev cCz2,c3 i112 314-0001 | iC TIMER NESSS U1, U2

TTEM| ary | cove HOMENCLATURE OF DESCRIPTION PARTS UST DIMENSIONS ARE IN INERES GREMLIN INDUSTRIES INC. _ 8401 AERO OR. SAN DIEGO, CA. 92123

DATE Tasha POWER INTERRUPT ASSY PARTS OVERLAY ‘SIE [CODE TOENT WO TORAWING RO. Cc BO7-001!12

FINISH NEXT ASSY USED ON ‘APPLICATION ‘DO NOT SCALE DRAWING

Page 33

\ pe MDA 3500 1 REV B PER ECN 3 WIE alsh7 Fate | TO ° ty | ' | 4 | IA A \ L

560-0003 B NOT ON RC, BOARD

1N523)

LAST C NO. USED C 19 LAST DNO. USED DO LAST Q NO. USED Q 10 LAST R NO. USED R 33 LAST U NO. USED U 4

GREMLIN INDUSTRIES INC. 840! AERO OR. SAN DIEGO, CA. 92123

Page 34

ore] oe DESCRIPTION DATE RER_ECN oS os [ansy.

_| CONN. MALE 4 PIN, CONN, MACE 10_PIN

=| xistoR Tip 2 Tie is = Tee = bolg—F-XisTORINEAOI ts —] rgron pasate

  • rE INGT4 0 = 7 4] DIODE MR 501

807-0002 Jo

ia ena I | PARTS UST “ YGREMLIN INDUSTRIES INC 8401 AERO DR. SAN DIEGO, GA. 92173 eae OWE 2 SUPPLY/AMP. BOARDIA -OMIT Ru PARTS OVERLAY —— & |p 807-0002E o [APPLICATION (00 NOT SCALE_ DRAWING. fecue 2 Xf aia _ [sneer or 7 7 6 3 4 3 2 1

Page 35

Sfvss

YI 20.790 MHZ O+— Ree 7 va a 74504] 4 | 74504 f U3, Of GS sbaye ad 19 1400 Py R39) 3 y 7

READY Ql re 4 ia CON TP3 )

rs 1K yp

TP4 iba PWRON SHT.2 1P7 3 5 Ae

  • 22

AviF POWER INTERRUPT BOARD IS NOT

BLANK KEYING PINS. NOTES: 1408

R28 220.2.

Rag

USE ADD Cit LON CONNECTOR PINS — 15, 27,39,44,48,52,54,57 ARE Uy

TRE 8080 A fe) CPU

READY H

RU RESET H Ais N.C.

1K Stk IK R26 gR2s gRr4 gR23 SRa7 1K ak

Us u U3) } Ps t—

Ya3)° 1o24x4 PROM 316-0016 Us 1024%4 PROM 316-0019

wr ps

pein f=

+12 OUT 7 SHT.2

OUT 6 sun ah

outs sHT.2

SUT. 2

ouT 3 SHT.2

ouT 2 © SHT. 2 OUT 1 SHT. 2

813-0001

IGREMLIN INDUSTRIES INC) 8401 AERO DR. SAN DIEGO, CA. 92123

{ 373-0001 | HUSTLE NXT ASSY, USED Of ‘APPLICATION. SCHEMATIC HUSTLE VIDEO LOGIC BOARD

Page 36

8 7 : 6 5 4 3 1

+12A2vt
ENV¢‘are | APonoveD,
SHT, 1RoswsVBLAN“5
Cpefees
60 Rsswae MEG OKme
DPyEstfr) Qu,to,Rei+
Cas,cmRane / 2N44015 8iD

3 ut

op uw‘tM3uikow3SE One.
Racop So47 2440"Rf| Rss3 Ree25vPRI ARs RRs Pre RRrg Pao
pitied)Rea de(OK
sGRet tL ayTeh 330

Ro 7 af

Lk dee

:lokRRr

Use ne sss PI 3aaK BB aj? nc Se

sT) TERe
4casaT

Ta bed BARK ium y RRoe

C c

B peat] B

7 7404 3 .

i _. IGREMLIN INDUSTRIES

Al oo4S401 AERO DR. FAN DIEGO, ZA.A

= SCHEMATIC —- HUSTLE VIDEO LOGIC BOARD 7 [rae ZXsuwPer a 1. PINS 9 TO 2 AT U35,U36 NOTES: NeXT ASST DRED OW == 7 APPLICATION. 6 5 4

Page 37

Terr Zi= 0oo4 vEer POINT FIN 230-0006 TAL 20. SS Manz CLS 213-0002 ‘SKT, 1s PIN SUAS INN im V2-Us (REr_ONL ope zie o004 conw MALE 4 PN. CONN. MALE OPIN 5 [zig= 0003 Bac. ORRD B/A LOGIE ISISTOR FN IFOS X1sistow ENAIO1 XISIsTOR SE 6055 LEB BES Diode ZENER TwSEOR DIoDs TN 4002 Siobe ZENER INS2 41

C28°C30,€34,C56,C 37, C3 C27,C35, i 120w a so pf Sov

3: er Cig. ca-C17, C192), C24 RTS, reer

A> UMPER WIRES AT NOTES. RES e =

ERT Se CNeTACCINCra cena RES PERE Raz R28 Red RSA ABE Lolako pol E be fo-f

RES RES REB_AGT_AT7 RASTA S7,R38-Ral RTA R50, 55, 864AS5,RE9 Re [RES Lic 172 Vs PRTe;R9, RO, RSS, ROS == hf

Sie SOIT Te Wears PROM 315-0015 .e 2ide RAM (SOON S) 3150018 gin Raw (Sa0Ns) 31a 0001 TIME NESSES 3133000 4 eM TAI Elo 314-0022 7486 B14-0028 [a= 038 [4-00 30) Bi4-00 39 3\@- 00a! B14 = 0010 [a=do81 Ula VSr, vel use U3 TELE flo} [lf

DED [== Sra cen

20,022,025 035 Uas-var ves “lelplceseep rill lei IE] vio = wis, UIs UIEURT UAE 23,054: U57 Yeo [Be,018 021,044 Vee Us.

TORTESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES FTOLERANCES ARE:

CAPACITANCE VALUES ARE IN MICRO FARADS EXCEPT © 7/3 NOTED AS PICO FARADS RESISTANCE VALUES ARE IN OMMS(K = 000) ON CONNECTOR PINS 3,527, 39,44,48, 52,54, 57 ARE BLANK KEYING PINS MIT O1,Q2, Di, D3,04,U3S, U36 C82 Rou avo

Se WIDEO LOGIC BOARD HUSTLE PARTS OVERLA [CODE TENT NO[DRAWING RO

Page 38
4321

REVISIONS

a)tone | orDESCRIPTIONot | arrnoven
F) @ Pre,LINITIAL RELEASE ECW 06fzCian

f PEAR PANEL, SUPPLIED WITH 140-0014 CABINET C [772 15 79: 250-0039 WAS.” 250-0108 |¥-2597 [uonye lec! G (2) D[ pee EON 1G wie | 5-9-7,

121-92 BOLT RD WD. CAkRiage /74L8)7) Dd
a8-92 HEX NUT|54
228 FLAT WASHER,I58
egi“8 LOCK WASHERH37
wet.1 BM ADHESIVE # XE -4699Se.
4i[810 LOCK WASHERi
rm70-22 HEX NUT4

3 (0-24. BOLT RD. hb CAkbnck 7H

ra_|" FLAT WASHER52.
a1 10-24 HEX UTEl
vstWO 2D HD CR 52, SHE MR. 5k. | fa be.50
Z16 FLT WD. ch Bic Weob Sch ihe,ad
2| S52 Stok OMe WD. MACH SEB 1/2 Lal48
i110-24 HANGEE BOLT Z72°LGl47
110-24 WING NUTHae

[+4 QD HP. ces. EC WOD_ Sc. 45

=[36 Sei? TAF STUN 5c NEXHO. 1/6 bsery
—[a WT=&AT. TOOTH LOCK WASHER43

#8 CLIP NAT +

copes w (44 (242)=E WD, WDcbs AEC SAT MT SCR TECa
STALL @)23=7ag} C

3 ScR>._ ITM 50 (ef) Fram FAR Ei} Sie, 2.

ra| CAeNET FEET[35

OPERATOR Panel ASS¥. SHET $2 cea | M | com gareverov PLATE 33, ASSY COW THOS BLOCK SHEET 2 OF} {3%

ASS JUMPER MAKES)SWEET 20F 9EN

EZ SHbET 20° 3 SHEET 2063 [24 55% SPEAKER OnBLE 38%. POWER INTERRUPT (ASS MOW/TOR HARNESS | SHEET 2063 __ | 28

(S) pecs._VIO LOG/cBD ASSY_ SHEET 2 0F321
.| WSSY POWER SUPPLYeneeT 142OF7| th
1"390-00/2| __ LAMP, FINTURE, FLyoR, 7SenceT 12 o3 | 25
{390-0011| LAMP, FLUORESCENT, 16"ry
|“corn SequTER 45517‘sweer 42 oF} | 2%

| Assy JUNcTION Box swesT 1 ¢2 0¢3 | 22 PANEL, MONITOR SceEE: Zr PANEL D/3piAY UPB PANEL, GRAPHIC FRONT ASE, SHADOW CABINET CRERETERR eo

WOLDINE ~TEIA LOWER WMOLDIG = TE IPPES TRIM CONTROL PANEL elie, SWITEH NS D

Z250-0034RETAINER SPRIIGx
4TPe50- 0037PLATE COCK STRIKE
1_|“250-0037BEZEL, FRAME
Tr [| 228-0076| __ com Box Lid ABBr.Pe
SEE DETAILZ[220-0075| ~~ L ATEN, Lock B/A\
OF ASS ON 812-09035[220-0012|CABWBOX, UPRIGHTb
5[psz0- 0018| Bie COIN HECHANIGABaer fz ors |e
Try220-0009LOCK, PANEL
mt1" 200-0002VIDEO, MONITOR 17 IN.SHEET 12 OFF | &
mt_| CABINET, B/R
fe(‘ow[SPEAKER COVER EXP2
$2)55,‘<SPEAKER , GAME EXPSHEET 192 OF 3 a
@) fics.:90] SRF | wenthrwe wo.Pied

PARTS UST Biers amen wenes || [NT Gremiin Industries, Ine.

V5qsel 5(4) PLCS."
sah 5a157racnons sesL—aA
Mess.=a <a oH5
aaTeRA4 S07J

USE 3M ADHESIWE “¥E-4699 TO CEMENT FRONT. RECKED es 7OP ASS¥ GEMS PANEL rast DY TE wrenET eM tien HUSTLE

ROTE ShOH BDF GE bwhdves, GEE GHEET 20F3 OF THIS DWG.7SE [COE TENT FO DRAWING AO.D

5 |

5.D|;

—— 7/3 0001

APPLICATION.DO NOT SCALE ORAWING.SCALE NONI[SHEET | OF
87654y-321
Page 39

REVISIONS. PER ECN *_@ rr e577 SHEET | ONLY [448-77 C| Bev. AFFECTS TONE | OTe &

[-) ) om |v] sc00-¢l2

LJ GAm 52) laws FLOURESCENT LAMP FIXTURE 18” P/N 390-0012

OVAL ex SOS; os eo SPEAKER CAQLE ee

ee A ve, ] 355

E | é 7 |

I 1} PI | . REAR VIEW { [| jz

\ 3 10 Pa Pov C an eel |e

Leon | & | | e oan, | 3s i pia ie a 4 es) ig 7 = DUA COIN MECH. P/N 220-0010 | |e Lao =| |e stk | E . euK B conTBOL Pees LS weLUME

a LONE, cry. Bug | eres | 8

=R9 ir BS = J

19” MONITOR CHASSIS, wir E nonsroe HARNESS AS9

Aeon Te vane BLK, TO MONITOR,

‘Sam Binge, Californie 92123 CABINET WIRING Gremlin industries, ine.

113-0001 HUSTLE RANE WO

[sneer 2 oF 3 “SEE [CODE BENT WO, DATE a/2s/r Is/si/> JSIMENSIONS ARE IN INCHES.

MATERA

og HUSTLE, {USED OW [SCnLE NONE 1DO_NOT SCALE DRAWING WET ASSY, FO MONITOR, WHT: ro noniron.crw-A

Rena vo wane toe = JUNCTION, Box Agcy

GAN SIDE_VIEW OF yuNcTION Box

TO TRANSFORMER, ‘oR ah Bue

LTO OPERATOR Switch ASSY. BLOCK Assy. (ke VIDEO LOGIC BOARD ASSY. FN 807-0001 @ JE SINCLE COND SHIELDED WIRE

ey

"APPLICATION.

Page 40

REVISIONS.

Done [aDESCRIPTION |DATE _ | srnaveD

ue | WINAL Becense Fee [Voie

zAlalpee cen * 0446>Za

Dl Per ccw # Ve oie [S577 Vd

os

<2}

I += 5

y

o534-.

| C)8)

nn Ww pak GS io ro D

1|Y (e

it H

err ttt tS oe oe H 1 { Go) @) REQD. @)EA. CEA) BUTTON ON FRONT EDGE

ATTACH GROUND _ WIRE SPADE LUG ~ CONN. HERE 718-0001 AYER EF, 4 PLAYER | Cer) /

10280-007PuATS Switen MT.7

—— —— . _ ae

“ ™ 1 Bact, GDA. 10-32 2" Ls CARRIAGE

ve253-0031SPACER, WICO WITEH

[a B13 - 0002 OPERATOR SWITCH ASS¥.

10.240 - 0008BUTTON, PLUNGER Assy.

\ 253-0020 | COVER, G2APHIC PANEL

N53-0027GRAPHIC PANEL, OPERATOR
i250-0102PANEL, OPERATOR

00] ent | oentrrNe wo. Oe DESCRIPTION PARTS UIST

ONE PLAY (REF) TWO_ PLAY (REF?

€ REF.

OPERATOR FANEL ASSEMELY DETAIL foNteSs oF DIMENSIONS ARE WNC FrOLERANGES ARE: NONI FRACTIONS DECIMALS = Oe oes TERWISE SPECIFIED [CONTRACT NO.

ANGLES,

OPERATOR PANEL AS9%

‘SIZE [CODE IDENT NO.TORAWING NO. T Re D 715-0061 |D [sHeeT_2 oF F

Page 41

D © virco ® L0G @— neving pw YEL

KEYING PIN GRY

WHT

Bik

BRN RED

yer |

FUR OOD Ic oats — conn.

i ! Seu —

BEN | ! lee RIGHT Ir2 poww Le2 carr ' ' [ter staaT

| 2PLR START PL IS THE LEFT PLAYER PACING THE GAME.

P2 13 THE RIGHT PLAYER FACING THE GAME.

TRANS FORMER

COM MECH 6.

GRY.

@Q— Keine Pn @ BLK REQ

ON COIN MECH COOR VEL

PIN B

$3,$4.ARE MOUNTED

VOLUME CONTROL

WHT (ANTENNA) N.C.

SPEAKER an SK" REVISIONS one | UT DescRIPTIOW Dare 7 NOTES: S| eee =. * fee ts ge a LN THESE JUMPERS ALLOW MULTIPLE Com O71770N. SOMBER ACCORDING 70 TABLE BELOW AH CONS, PER GAME JUMPER PINS.

Tere 8 AXTHIS JUMPER SETS GAME TIME ‘2 MINUTE GAME, JUMPER OUT 772 MINUTE GAME, JUMPER 34-31. Ay FREE GAME SELECT No FREE GAME.

120v. @BMooTH

100V ® TRIGGER START SINGLE

Ov © 1B INCH FLUORESCENT RIBBED ine

TO TRANSFORMER

TO +5 ENG OF R2, INTERLOCK SWITCH ON POWER SUPPLY / AMP. BD 5 19 INCH MONITOR

POWER BOX ~ POWER INTERRUPT Q 207-0012 TO TPA ON VIDE LOGIC BD. g ?

fe

To TP4 GN VIDEO LOGit BD.

IR SSWIELDED WIRE El ane aban Foo} Gent | woentieyG no. a SeScRirron see REMUN INDUSTRIES INC. re ft AERO DR. SAN DIEGO,CA. 92123) A

POWER SUPPLY CONN pa ee | SCHEMATIC. — HUSTLE ‘aicamanan tae CABINET WIR /RING [ae

1DO_NOT_SCALE_DRAWING [CODE TDERT NO. ORAPONG NO. D| 7/3 -O001 | [scale _WONE] sneer 9 OFF, 2 1