Gravitar Black Widow Retrofit TM-232 2nd Printing
Gravitar Retrofit (Atari, Inc., 1983) · Technical Manual · 28 pages · 14 sections · original scan
TM-232, 2nd printing.
GRAVITAR™ RETROFIT
Instructions
ATARI, INC. 790 SYCAMORE DRIVE P.O. BOX 906 Vk MILPITAS, CALIFORNIA 95035. 408/942-3100 ¢ TELEX 35-7488
o- Warner Communications Company
If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below. WEST and CENTRAL U.S.A.
Atari, Inc.
California Customer Service Office
2 Morte ie a Telex 17-1103 /, 7:30-4:00 pm Facific Time)
Pod From California, Alaska, or Hawaii
(408) 745-2900 Service from anywhere in the area shown in white ol-tree (800) 538-1611
EAST U.S.A. Service only MICH. if Atari, Inc. 128 Worlds Fa Dive, Somerset N 124 's Fair Drive, Somerset, NJ 08873 Telex 37-9347
GRAVITAR” RETROFIT
Instructions
2M
ATARI, INC. 790 SYCAMORE DRIVE @ P.O. BOX 906
ATARI MILPITAS, CALIFORNIA 95035
408/942-3100 TELEX 35-7488
© 1983 Atari, Inc. All rights reserved.
No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976.
This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal actim is pending. If infringers are
convicted, courts can order destruction of the infringing
articles,
In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year.
Atari will aggressively enforce its copyrights against any infringers. We will use all legal means. to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game. -
Published by:
ATARI, INC.
790 Sycamore Drive
P.O. Box 906
Milpitas, California 95035
Printed in the U.S.A. 2M
ii
Table of Contents
Kit Parts Inventory..... . Tools Required for Retrofit..... Retrofit Instructions...........26 Remove the Attraction Glass...... Remove the Control Panel....... Remove the Game PCB........eeeeeeceeee
Assemble the Control Panel. Install the Wiring Harness. Install the PCB...........- Install the Control Panel........ Install the Attraction Glass.. Install the Decals.......... Change the Model Number..... Install the. Self-Test Chart...... Perform a Self-Test..........eceeereee ee cccccccccccecs Change the Gravitar Schematic Package...cccececccenecccccscccs
List of Illustrations
Figure 1 Location of Gravitar Parts Affected by Retrofit... Figure 2 Location of PCB Components Affected by Retrofit... Figure 3 Assembling the Control Panel.........sceeecccceece Figure 4 Harness Wire Installation........ccsesceeccceccees Figure 5 PCB Edge-Connector Wire-Tie Installation.......... Figure 6 Sheet 1B (Gravitar Main Wiring Diagram) Changes... Figure 7 Sheet 5A (Gravitar PCB Schematic Diagram) Changes. Figure 7A Sheet 5A (Gravitar PCB Schematic Diagram) Changes. Figure 8 Sheet 11A (Gravitar PCB Troubleshooting) Changes.. Figure 9 Sheet 11B (Gravitar PCB Troubleshooting) Changes..
List of Tables
Table 1 Retrofit Contents........cccccceccccccccccnccccces Table 2 Tools Required for Retrofit.. eee cece cree econ Table 3 IC Component Locations....... £0400. 06s o64i60 Hee Table 4 Player and DIP Switch Inputs.......cceceecccecceee OODUARANNEH
wOnwW
yu NE
iii
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Gravitar™ Retrofit Instructions
Introduction
The following information includes the necessary retrofit instructions for changing the Gravitar upright game into a Black Widow game. The modifications include changing the cabinet graphics, the control panel, the harness assembly, certain game board components, and the self-test label. Information is also provided for changing the Gravitar Schematic Package Supplement (SP-206) to reflect the Black Widow circuitry.
Kit Parts Inventory
Check the contents of the Black Widow Retrofit Kit (A040037-01) before proceeding with the retrofit procedure. Note that the integrated circuit (IC) components included in the retrofit kit are labeled with their respective part numbers. The parts included in this retrofit kit are listed in Table 1.
Table 1 Retrofit Kit Contents
Part No. _ Quantity Description i
| A040039-01 | 1 | Electronics Kit—Includes the following: |
| 110000-223 | 1 | 22 kR, +5%, 1/4 W resistor |
| 128002~101 | 1 | 100 pF, 100 V fixed mica capacitor |
136017-101 to -110 10 Integrated circuits
| A039975-01 | 1 | Control panel with decal |
| A039989-01 | 1 | Control panel harness assembly |
| A039990-01 | 1 | Main conversion harness assembly |
| A040040-01 | 1 | Attraction glass assembly |
| ST-234-01 | 1 | Self-test chart |
| TM-234 | L | Black Widow Operators Manual |
| 62-039 | 2 | SPDT momentary pushbutton start switch with |
red light-emitting diode
| 75-010S | 8 | #10 flat washer |
| 75-5112B | 8 | 10-24 x 3/4-inch black carriage bolt |
| 75-9415 | 8 | 10-24 hexagonal locknut |
| 036895-01 | 2 | Black molded switch bezel |
(continued on next page)
Gravitar Retrofit Instructios
Table 1 Retrofit Kit Contents (continued)
Part No. Quantity Description :
| 039978-01 | 1 | Left side~panel decal |
| 039978-02 | 1 | Right side-panel decal |
| 040002-01 | 1 | Printed-circuit board (PCB) label |
| 171021-001 | 2 | 8-position joystick |
Tools Required for Retrofit
The tools listed in Table 2 (or their equivalents) are required to performa complete retrofit modification.
Table 2 Tools Required for Retrofit
a
| Quantity | Description | Purpose |
| 1 | 1/8-inch Allen wrench | Install attraction glass |
| 1 | 3/8-inch hex-nut driver | Assemble control panel |
| 1 | 7/\6-inch hex-nut driver | Install control-panel |
| 1 | Diagonal cutters | Remove PCB components |
| 1 | Needle-nose pliers | Install PCB components |
| 1 | Phillips-head screwdriver | Remove access panel and PCB |
| 1 | 16-27 W soldering iron | Install PCB components |
| 1 | Squeegee | Install decal graphics |
Retrofit Instructions
These procedures mist be performed by qualified service personnel.
The following procedures are arranged in a sequence recommended for performing the retrofit modification. The parts of the Gravitar game that are affected by the modification (see Figure 1) are removed first. Next, the game PCB is modified. Then, the modified PCB and the remaining kit parts are installed.
Attraction Glass Assy.
Decals Right & Left Side
Game identification
Main Hamess Assy. See Figures 3 & 4
Control Panel Assy. See Figure 3
Self-test chart on rear access Panel not shown. Replace with Black Widow version.
Figure 1 Location of Gravitar Parts Affected by Retrofit
Unplug the game before performing the following procedures.
Remove the Attraction Glass =
- Use the 1/8-inch Allen wrench to remove the three screws and washers that fasten the top retainer to the cabinet. Remove the retainer. Keep the screws and washers for reassembly.
- Loosen the three screws that fasten the bottom retainer to the cabinet. Remove the attraction glass.
- Remove the three screws and washers from the bottom retainer. Keep the screws and washers for reassembly.
- Remove and discard the foam tape from the underside of the top and bottom retainers. Keep the retainers for reassembly.
Remove the Control Panel
- Use the Phillips-head screwdriver to remove the screws that fasten the access panel to the back of the game cabinet. Remove the access panel.
- Reach inside the game cabinet and release the two spring-draw latches on the back of the control panel.
- Grasp the top edge of the control panel from the front of the game cabinet and swing the panel down to expose the three mounting bolts.
- Disconnect the cable connector at the back of the control panel.
- Use the 7/16-inch hex-nut driver to remove the Gravitar control panel from the cabinet. Keep the bolts, washers, and nuts for reassembly.
Remove the Game PCB
- Disconnect the two edge connectors from the game PCB.
- Use the Phillips-head screwiriver to remove the screw and spacer that secure the game PCB to the cabinet. Keep the screw and spacer for reassembly.
- Carefully slide the PCB straight out of its slots. Be careful not to twist the board to avoid loosening connections or components.
Modify the Game PCB
“NOTE
The game PCB must be removed from the cabinet before performing this procedure.
- Remove the 10 integrated circuits (EPROMS) from the locations shown in Figure 2.
- Install the 10 integrated circuits from the retrofit kit in the PCB locations shown in Table 3. Refer to the part numbers labeled on each IC and use Figure 2 to determine their locations.
Table 3 IC Component Locations
Ic Part No. Location
136017-101 DL 136017-102 E/F1l 136017-103 HL 136017-104 Jl 136017~105 K/LL 136017-106 ML 136017-107 L7 136017=108 M/N7 136017~-109 N/P7 136017-110 R7
Refer to Figure 2 for the locations of the components removed and replaced in steps 3 through 5.
- Use the diagonal cutters to remove capacitors C28 (0.001 uF) and C34 (0.22 uF). These components are not used in the Black Widow game.
Figure 2 Location of PCB Components Affected by Retrofit car
Replace with 100 pF
Replace Label
*Replace these integrated circults with those from the retrofit kit that have part numbers as shown in each location. “x +s 2 Za
Use the soldering iron and needle-nose pliers to remove capacitor C27 (0.001 uF) and resistor R46 (10 kt). Replace C27 with the 100 pF capacitor and R46: with the 22 kQ resistor from the kit. Be careful not to overheat the PCB. Excessive heat can separate the conductive material from the board.
- Remove the protective backing and attach PCB label (040002-01).
Assemble the Control Panel
Refer to Figure 3, Assembling the Control Panel, when performing the following procedure.
Insert the two black molded switch bezels into the two holes on the left front of the control panel. Make sure the switch bezel tabs are inserted into the hole slots.
Hold the bezels in position and hand-tighten the two pushbutton start switches into the bezels.
Insert the 8-position joystick handles through the control panel holes and use the 3/8-inch hex-nut driver to attach the carriage bolts, flat washers, and hexagonal locknuts..-
Connect the wire harness leads to the pushbutton start switches and joysticks. The lead pairs to each joystick switch can be attached to either terminal.
Peel the protective backing from the l-inch wire harness cable mounts and firmly attach the wire harness to the control panel. -
Attach the ground clip to the control-panel latch bracket so that the Clip contacts rest in the clean unpainted area on the bracket.
Install the Wiring Hamess
1. Insert the four wires from the main conversion harness assembly into the pin sockets of the 44-pin PCB edge connector as shown in Figure 4. Make sure the contacts are positioned properly before locking the pins in place.
Use five wire ties from the retrofit kit to secure the four harness assembly wires to the existing Gravitar main wire harness that runs underneath the game PCB and toward the control panel.
Figure 3 Assembling the Control Panel Black ‘Common Red (+) le Grey/Whit Cera Open VioletWhite
‘Black Common ee em Open White/Black
Figure 4 Hamess Wire Installation
Install the PCB
- Carefully slide the modified game PCB into its mounting slots. Make ‘sure the foam pad is secured to the cabinet near the center of the PCB.
- Attach the PCB to the cabinet with the screw and spacer.
- Connect the two edge connectors to the PCB. Make sure the PCB is inserted firmly against the back of the connectors.
- Secure the edge connectors to the PCB by fastening a wire tie around the eye at each end of the two connectors and through the hole in the PCB as shown in Figure 5 (total of four ties).
il
Figure 5 PCB Edge-Connector Wire-Tie Installation
Install the Control Panel
- Securely fasten the Black Widow control panel to the game cabinet with the- three mounting bolts, washers, and nuts previously removed from the Gravitar control panel.
- Securely fasten the two connectors at the back of the control panel to their mating connectors on the main harness assembly.
- Close the control panel. Reach into the back of the game cabinet and fasten the two spring-draw latches at the top edge of the control panel.
Install the Attraction Glass
- Loosely fasten the bottom retainer to the game cabinet with the three mounting screws and washers.
- Slide the Black Widow attraction glass into the bottom retainer.
- Hold the top retainer tight against the top of the attraction glass and securely attach the top retainer to the game cabinet with the three mounting screws and washers.
- Press the bottom retainer tight against the attraction glass and tighten the three mounting screws.
Install the Decals
We recommend that the following installation procedure be performed by two persons. One person may have difficulty handling the cabinet and the large decals.
- Tip the game cabinet sideways and gently lay it on a soft blanket.
- Thoroughly clean the side of the game cabinet to ensure the removal of all dust.
- Grasp the top edge of the appropriate decal for the side of the game cabinet. Hold the decal up off the floor and peel away the protective backing.
4 Gently lay the decal, sticky side down, in the center of the game cabinet. Position the decal to allow about three-quarters of an inch between the edges of the decal and the edges of the cabinet.
The adhesive side of the decal has glass beads that will permit positioning of the decal. DO NOT PRESS DOWN on the decal until it is in position or the glass beads will break and set the adhesive.
S. With the decal down and in position, use the squeegee to break the glass beads ani set the adhesive by quickly working from the center to the outside edges.
- When the wrinkles are removed and the decal is in position, gently tum the game cabinet over to the opposite side. Be careful to avoid damaging the freshly applied decal.
- Repeat steps 1 through 6 for the remaining decal.
- Carefully raise the cabinet to the upright position.
- When both decals are firmly affixed, remove the protective. covering. Allow time to dry before proceeding!
Change the Model Number
Permanently mark the game identification serial number label (see Figure 1) with model number 33100-01.
Install the Self-Test Chart
Replace the Gravitar self-test chart on the inside of the rear access panel with the Black Widow self-test chart.
Set the Option Switches
- Set the option switches as described in the Black Widow Operators Manual.
- Replace the rear access panel on the game cabinet.
Perform a Self-Test
- Plug the game in.
- Set the power on/off switch to the on position.
- Perform the self-test procedure as described in the Black Widow game manual. Be sure to adjust the x- and y-axis potentiometers as described on sheet 8B in the Gravitar Schematic Package Supplement.
Change the Gravitar Schemtic Package
The circuitry given in the Gravitar Schematic Package Supplement, SP-206, applies to the Black Widow game after the following changes have been made:
® Sheet 1B, Gravitar Main Wiring Diagram: Replace the Control Panel section of the wiring diagram with Figure 6.
® Sheet 5A, Gravitar PCB Schematic Diagram: Replace the Option Switch Input, Audio Output, and Coin Door and Control Panel Input schematics with Figures 7 and 7A.
® Sheet 5B, 6A, 6B, 7A & 7B, Gravitar PCB Schematic Diagrams: The signatures shown in color do not apply for the Black Widow game.
© Sheet 11A, Gravitar PCB Troubleshooting: Replace the Memory Map with Figure 8.
@ Sheet 11B, Gravitar PCB Troubleshooting: Replace Table 4, Player and DIP Switch Inputs, with Figure 9.
@ Sheet 12B, Gravitar PCB Troubleshooting (2nd printing only): Delete Troubleshooting with Checksums procedure.
TO P2O-8 FtRE UP TO. P2O-K FIRE. DOWN. TO P20-9 FIRE LEFT TO P20-L FIRE. RIGHT Rien RiBk use| 4 suns aria
Figure 6 Sheet 1B (Gravitar Main Wiring Diagram) Changes uP aro?
RIGHT re ae : Th pee ope les
Figure 7 Sheet 5A (Gravitar PCB Schematic Diagram) Changes
Coin Door and Control Panel Input
Figure 7A Sheet 5A (Gravitar PCB Schematic Diagram) Changes
| a 07 08 D5 Ds 03 02 D1 DO MEMORY MAP
g = g z ® g j z
u LAY! PLAYER 1 LED IN LC BANK SEL COIN CNTRL COIN CNTR
OPTION 2 OPTION + OPTION 0 SPARE
Pabapapabs Baeas EERE e00000000 900000000 eo00000000 920000000 200000000
Figure 8 Sheet 11A (Gravitar PCB Troubleshooting) Changes
Table 4 Player and DIP Switch Inputs
Right coin switch, Left coin switch, Auxiliary coin switch, Self-Test switch Left Joystick
ADDRESS TEST RESULTS
DATA display changes when any coin switch or the Self-Test switch is activated. Upper nybble of DATA display is unstable. DATA display changes when any of these input switches is activated.
DATA display changes when any of these input switches is activated. . Right Joystick Start 1 Start 2
Figure 9 Sheet 11B (Gravitar PCB Troubleshooting) Changes
F ‘soinqinsip yons Aq pawsojsed st yory s0ge] Surpnyur UONLoyIPow Aue JO aed EAy-uOU Aur Jo Arazes 30 AaTiquains ‘Aayfenb oy) Joy a1q!sUodsas 9q OWNED IEEIY ‘Sa}JOSSIII" JO sured LEY UEYI Jay SaOssadIe JO sized [Jas ACW Ay uaw8pn{ s9y) Uy ‘paresodo pur paumo Ajaiealid Bulag ‘uspuadaput are sIOINqIsIp Hey : “Aiayes nOA ainsud 01 J9pPIO ‘uy ‘soure8 sno yam s1UsUOdWOD parjddns-eay-uOU ZuIsN UT snOMNeED AJaA ag “sIOYI0 PUE NOK 01 Aan{uy asneo pur sures sno Jo Arages au 1Daye ATassaape Oste Aw sized pe1y-UOU Aue JO asn ay, “Ayuvssem ap Jo suai ay 01 Buypsodo8 ‘AqueITEM INOA proa Avu sized peIy-UOU Aue JO asN ay,L uaries &q stonpo.d Jo avs aqi qiym uo} -28UUOD Ut 5911111401] 4aq10 KuD 4a}{aS aq1 4of aunssD 0} UOSLad 42q10 KuD SaztLOqInND 40U SaUiNssD doqitau 11 pun ‘and S, an1as aqi UO Sati111qQD1 40 su0110811G0 4q10 110 fo puv ‘esodand 4vjn211 PC ipa tpn nine ane peace pelican tard ‘panydus 40 passasdxo sauupsavm 40q10 110 fo nat] us, AqUDLLOM $141 “Uuja49q SULLA aGi SapassadNS 194IUOI goign sakng pun saqjas usamsag 19041u09 uarit4m v us qusofias Kyuv.uvm ssesdxa Kuv 40f 1deoxq “so8eurep [enuanbasuod JO TeUapPuT ‘9sn JO ssoy ‘sIJOId JO sso] JOJ 2IGET 9q JOTIES EUS IUDA2 OU UT “Buns sodosdun Jo ‘uoneesut stedas odosdut ‘uonesaye ‘09/8ou ‘osnstus “1uap1ooe Aq PIsned 10U aIDA PUE PaISTX $192J9p P2B2] “Te yons 1eIp VORDEIsNES S,J2]]9$ 01 S2sopostp sIONposd pres Jo UONEUTUTEXS $,J2T12¢ (9) pur ‘juejd s.so1]2g 01 predasd pousmaas ase sionposd yong (q) soanoayap ae sxonposd pres 3etp soAng Aq Axaaoostp uodn 8untim ur paynou Apduwosd s1 32719 (e) :papraoad ‘poyiad Aueszem pres Surmnp JaT]9g 01 pousNaT ‘are yoru syed SpuONDaTO Yons JOJ 1NODde s,JoANg Mp2Id JO ‘soe;dar 01 ‘uondo si 1e 9q Treys Aammqey 210s s,s97}ag AauesTEM stp OF WIOTWOS 02 [Tey PY STU UI fuONDa]> 3U1 31 -drys Jo ap woy skep (96) AauTU Jo popad ¥ Joy d>1AJ9s pur sn TeEWIOU JopuN drysueuTyIOM (PUR [eLaIEW UT sIDJJOpP WoY sayy aze IF Sy UE parddns syzed SyuONDa] $y} Ietp SIULITEA J9T[OS
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.