CATHODE RAY TOMES

Golden Tee 97

Golden Tee '97 (v1.30) (Incredible Technologies, 1997) · Manual · 38 pages · 51 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

INCREDIBLE TECHNOLOGIES, IN

SERVICE / SALES (800) 262-0323 FAX (847) 870-0120

| Hardware and Software ©Copyright 1997 Incredible Technologies, Inc. All rights reserved.

WARRANTY, REPAIR and RETURN POLICY

© 90-doy warranty on all electronic components. All warranty periods begin on the date of purchase from Incredible Technologies, Inc..

  • There is a minimum $40.00 service charge for all non-warranty repairs or returns.

«For all servicing return to Incredible Technologies, Inc.

» ANY non-factory repair or attempted repair voids warranty.

  • AAMA decal must not be removed from the PCB, Warranty voided if removed.

RETURN MERCHANDISE AUTHORIZATION

© Allreturned merchandise must have a Return Merchandise Authorization (RMA) number marked clearly on the outside of the package.

«You must obtain all RMA numbers from your authorized Incredible Technologies, Inc. distributor. Please have your Incredible Technologies, Inc. serial number available when calling for an RMA number.

  • Merchandise returned without an RMA number will not be accepted.
  • Advance replacement boards will be shipped to distributors or, at the distributor's request, will be shipped directly to the operator

¢ Advance replacement boards will be billed to the distributor until Incredible Technologies, Inc. receives the returned board, at which time a credit will be issued.

© Allrepairs and/or replacements will be shipped within 24 hours of receipt or request (subject to availability).

FCC REGULATION COMPLIANCE

This equipment complies with the limits for o Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. 02/97

Page 3

TABLE OF CONTENTS

GAME PACKAGE CONTENTS. RECOMMENDED TOOLS AND SUPPLII n nN

2 INSTALLATION PREPARATION

THE CABINET. Power Requirements. Monitor Requirement: Cabinet Selection Preparing « used cabinet for GOLDEN TEE '97 THE CONTROL PANEL. Trackball Preparation Button Preparation... THE GRAPHICS OVERLAY Control Panel Overlay Installatio Function Labels Overlay Installatio: Marquee Installetion.. WIRING AND HARDWARE ASSEMBL Control Panel Assembly .... Printed Circuit Board (PCB: Wire Harness.. Power Wires. Monitor Wires Speaker Wires

Coin Doors, Test Switch, Service Button, and Volume Control Panel . Mars Light Hookup wenn nv

DOMONNNNADaranww

www Final Check

S INITIAL START-UP ascents 10

4 DIP SWITCH SETTINGS... scssssnnsnnnn 10

B OPERATOR MODE... ccnnsinnninnesnintnin rn

VOLUME SETTINGS .......ccccsssssssscssssssssseseeesesesssns OPERATOR ADJUSTABLES Game Mode Selection Game Resets......... Attract Mode Sounds Credits and Coin Door Setting Delay Time Adjustment. Skill Level Adjustment ... Hole In One Contest Mode Coin Door Protection Menu. GAME AUDITS Display Coin Audits Display Game Selection Audits. Number of Golfers and Holes Played Pine Creek Audits Coral Ridge Audit Red Sands Audits Display Hardware Audits Reset Audits............ LEADER BOARD MENU. Display Leader Board Menu Clear Leader Board Men SYSTEM TESTS...... Video Screen Tests. Full GROM Checksum Test Fast GROM Checksum Test Video Ram Test Palette RAM Test Board Tests . Sound Tests. Control Panel Voltage Adjust Test

APPENDIX A GENERAL TROUBLESHOOTING

VIDEO PROBLEMS . SOUND PROBLEMS CONTROL PROBLEMS. POWER-UP PROBLEM: MISCELLANEOUS PROB

APPENDIX B JAMMA HARNESS CONNECTION... crcsccocsce 30

JAMMA HARNESS CONNECTION. TRACKBALL CABLE CONNECTION.

APPENDIX C T/O and JAMMA SCHEMATIC ..sssccsssssessnssene 32

APPENDIX D WARRANTY INFORMATION .....cccsssssssseasee 34

Page 4

INSTALLATION PREPARATION

GETTING STARTED

BEFORE YOU START.....

  • Check to see if all the needed parts have been . included in your kit (See GAME PACKAGE CONTENTS .)
  • Printed Circuit Board (PCB) Assembly 2. Do you have the necessary tools? (See
  • Connecting Wire Harness (JAMMA) RECOMMENDED TOOLS AND SUPPLIES
  • Trackball Assembly w/Metal Plate {1) Trackball Cable Assembly
  • Button Assemblies
  • Marquee Styrene
  • Marquee Plexiglas
  • Control Panel Overlay
  • Set of Function Labéls
  • Manua
  • Do not work with any part of the system plugged in (lights, monitor, or power supply).

POWER REQUIREMENTS

Make sure the game you have chosen to convert is able to supply ail the required voltages for GOLDEN TEE '97.

+ Phillips and Slotted Screwdrivers

  • Socket Set +5 VOC Samps
  • Wire Cutters and Strippers +12 VDC 2 amps ;
  • Pliers or Channel Locks : © Electric Drill with 3/32", ", and 7/16” Bits |
  • Chassis or Sheet Metal Punch Hl
  • Small File

© Razor Knife and Sharp Blades WARNING!!!

© Straight Edge The output level of many "regulated" switching

  • Staple Gun and Staples power supplies actually vary with load. For this
  • Soldering Iron and 60/40 Resin Core Solder reason, the power supply from an old game may not © Vacuum Cleaner be correctly adjusted for GOLDEN TEE ‘97. This + Assorted Fastening Hardware makes the existing power supply inappropriate and © Heat Shrink Tubing (3/32", 1/8”, and 3/16”) hazardous to your new game. Therefore, it is very
  • Masking Tape important to adjust the +5 VDC supply WITHOUT © or 4" Wire Ties connecting the PCB, then readjusting it later, after the PCB has been installed. Measure power IF YOU DO YOUR OWN PAINTING, on the PCB, onan I.C.. Damage will occur if the YOU'LL NEED THESE PAINT SUPPLIES: © Air Brush or Paint Sprayer
  • Paint Roller and Pan + Paint Brush ¢ Paint (and Primer)

2 - GOLDEN TEE 3b GOLF

scubavaseueoervsrneaayansnnnysceaa es saci ashame tetaeaaeaaatun eco Ire il i LA mr a LURE UAL eS RA LALA power supply is outside the acceptable limits {between 4.8 and 5.5 VDC.)

Page 5

MONITOR REQUIREMENTS

GOLDEN TEE '97 requires a monitor in a horizontal mount raster scan with negative composite SYNC. It can be difficult to change the monitor from vertical to a horizontal unit, therefore, installation will be easier if you choose a horizontal mount cabinet.

CABINET SELECTION

You can choose either a new cabinet or a used cabinet for your GOLDEN TEE '97 game, Reusing a cabinet is by far the most cost-effective way to maximize the return of your initial investment. In either case, all you need to provide is the cabinet with a power supply and monitor. We provide the rest, The end result is a new game at a very low cost.

NOTE: ‘ It is recommended that a large contral panel with 0.25" monitor, like those ona 4-player cabinet, be used for your GOLDEN TEE '97

When selecting a cabinet, keep this in mind: A cabinet with a 25" monitor and a large control panel will allow you to mount the trackball farther from the monitor. This prevents players hands from hitting the monitor glass when rolling the trackball forward, and will earn better than a smaller control panel with a smaller monitor.

PREPARING A USED CABINET FOR GOLDEN TEE '97

  • Remove the following from the cabinet:
  • Main Logic Board(s)
  • Control Panel
  • Monitor Plexiglas
  • Marquee
  • Cabinet Graphics
  • Thoroughly clean out your cabinet. Remove all the old buttons, joysticks and wires from the control panel. DO NOT remove monitor and speaker wires.
  • Remove the old graphics and adhesive from the control panel, and the side of the cabinet. Remove adhesive with solvent.
  • Fora fresh look, painting is highly recommended, Spray painting gives a better finish, but if an air brush or paint sprayer is unavailable, a roller is second best, Remember to cover all exposed surfaces not to be painted,
  • Remember, spending time on the cabinet's appearance (i.e., marquee, contro! panel, and cabinet graphics) will raise your profits with the introduction of a new game package, especially if the cabinet looks clean and new.
  • The “new game look" should always apply to the inside of your game as well. A few wire ties and shrink tubing on your harness, some fastening hardware on your subassemblies, and a sweep with the vacuum cleaner will ensure that glitches do not occur,

Mounting the trackball carrectly and securely is very important for the profitability of your new game. Follow these instructions carefully for mounting the trackball to: 1) a metal control panel: 2) a wooden control with routing: 3) or a wooden control panel without routing. (Refer to template inserts which came with your new kit.)

NOTE:

Installing the trackball as far away from the tmonitar as possible wil! prevent players hands from hitting the monitor glass when rolling the trackball forward.

CONTROL PANEL LAYOUT (TRACKBALL MUST BE CENTERED ON THE CONTROL PANEL)

GOLDEN TEE 3D GOLF - 3

Page 6

TRACKBALL PREPARATION

When making the hole for the trackball, follow the instructions, starting on the right, for the type of control panel you will be using.

NOTE:

When installing the trackball, make sure the trackball is in the right orientation. (Refer to picture below.)

MONITOR i= 7 a =

i

S

eo

e IMPORTANT: Pont acco ten or he Met Gabe ex ave reo mainees moore so core craton

TRACKBALL ORIENTATION {NOT DRAWN TO SCALE)

IMPORTANT:

The supplied trackball comes equipped with a grounding cable. This cable must be connected to field ground to protect the trackball P.C, boards from becoming damaged by electro-static discharge. Te mount trackball to a metal contro! panel use TRACKBALL MOUNTING TEMPLATE #1

Fill any existing holes in the metal control panel. Place and secure TEMPLATE #1 to your control panel in the desired location.

NOTE: The trackball should be as far away from the monitor as possible. . Carefully drill the holes for the ball and the mounting bolts using the template as a guide. Remove template and file down any rough edges. See THE GRAPHICS OVERLAY section on page 6 on how to install the graphics. . Mount trackball under the metal control panel using the four carriage bolts.
NOTE: Be sure the trackball is mounted as shown in the diagram on page 4.
NOTE: Do not over-tighten the trackball. It will warp and cause the trackball to not operate correctly.
NOTE: The supplied metal plate is not needed with metal control panels.
NOTE: Be sure to mount the trackball so as much of the ball is exposed as possible. Securely fasten the trackball grounding wires to Field Ground in your cabinet. This step is
important in reducing static buildup and discharge caused by the trackball. . If using Plexiglas on your control panel, it is highly recommended that a 3-1/2" hole be cut in the Plexiglas for the trackball, This allows for players to use the full height of the trackball. Carefully file and smooth the edges of the hole in the Plexiglas so players do not cut their hands when playing.

4- GOLDEN TEE 3D GOLF a marsoce senna em utils eee Ellon SUNG ARC DE ECC A a A So aS aT Te

Page 7

To mount trackball te a wooden control panel with routing capability use TRACKBALL MOUNTING TEMPLATE #2

10. Fill any existing holes in the wooden control panel. Place and secure TEMPLATE #2 to your control panel in the desired location.

NOTE: The trackball should be as far away from the monitor as possible. Carefully cut the hole for the trackball in the shape indicated on the template. Drill the mounting holes indicated. Next route out the shaded area indicated on TEMPLATE #2, 1/16" deep. Use a 1/2" Rabbiting Bit for best results. This is so the supplied metal plate will be flush with the control panel surface. Remove template and file down any rough edges. ; See THE GRAPHICS OVERLAY section on page 6 on how to install the graphics. Mount trackball to the metal plate using the four carriage bolts supplied. Then mount the metal plate to the wooden control panel,
NOTE: Be sure the trackball is mounted as shown in the diagram on page 4.
NOTE: Do not over-tighten the trackball, It will warp and cause the trackball to not operate correctly.
NOTE: Be sure to mount the trackball so as much of the ball is exposed as possible. Securely fasten the trackball grounding wires to Field Ground in your cabinet. This step is
important in reducing static buildup and discharge caused by the trackball. Tf using Plexiglas on your control panel, it is highly recommended that a 3-1/2" hole be cut in the Plexiglas for the trackball. This allows for players to use the full height of the trackball, Carefully file and smooth the edges of the hole in the Plexiglas se players do not cut their hands when playing. Te mount trackball to a wooden control panel without routing capability use TRACKBALL MOUNTING TEMPLATE #3

Fill any existing holes in the wooden control panel. . Place and secure TEMPLATE #3 to your control panel in the desired location.

NOTE: The trackball should be as far away from the monitor as possible. . Carefully cut the hole for the trackball in the shape indicated on the template. The trackball should fit the hole shape exactly.
  • Drill the mounting holes as indicated. . Remove template and file down any rough edges. Using the TRACKBALL ORIENTATION TEMPLATE, cut a 3” hole in the Plexiglas overlay to fit over the trackball. Be sure to include holes for the buttons, and all of the mounting bolts. See THE GRAPHICS OVERLAY section on page 6 on how to install the graphics. . Insert the trackball into the newly cut hole. Place Plexiglas overlay on top of the control panel. Place the supplied metal plate under the trackball and use the carriage bolts to secure it to the control panel. The metal plate below and the Plexiglas above will secure the trackball assembly into position.
NOTE: Be sure the trackball is mounted as shown in the diagram on page 4.
NOTE: Do not over-tighten the trackball, It will warp and cause the trackball to not operate correctly.
NOTE: Be sure to mount the trackball so as much of the ball is exposed as possible, Securely fasten the trackball grounding wires to Field Ground in your cabinet. This step is
important in reducing static buildup and discharge caused by the trackball.

GOLDEN TEE 3D GOLF - 5

Page 8

* BUTTON PREPARATION

1, When making the holes for the buttons, DO NOT use the Function Labels to outline any new holes, The Function Labels are designed to fit right over the buttons when installed on the control panel. If the labels are used as a template the holes will be too big, and the buttons will fall through. Instead, use the labels as a guide to where you want to drill your new holes, and then cut a 1-1/8" hole in the center of where the labels are to be placed. DO NOT stick the labels to the panel at this time.

  • Drill or punch the holes marked for buttons or bolts, Use a chassis or sheet metal punch for best results on button holes.
  • Usea file to smooth any rough edges on the holes.
  • Fill any old and unused holes with wood, resin, or a metal plate.
  • It is recommended that you cover your control panel with Plexiglas, Now would be a good time to cut it to fit while the dimensions and tools are at hand.

iain

GOLDEN TEE '97 comes equipped with graphics that will accommodate a variety of existing game cabinets.

CONTROL PANEL OVERLAY INSTALLATION

——————— ES

  • Make sure the control panel is clean and free from dust, grease, metal filings, and sawdust. The background overlay provided with the game is oversized to accommodate most control panel sizes. Center the background overlay on the control panel surface. Be sure to leave enough excess material above and below the control panel in order to trim it evenly. 2, Remove the protective backing from the background overlay. Center the background overlay over the control panel and place down

6 - GOLDEN TEE 3b GOLF gently, making sure to keep it square. Using your hands, press down firmly, starting from the center and smooth the background overlay outward, making sure all bubbles have been pressed out for a clean, flat surface.

  • Using a sharp razor knife, trim any excess from the background overlay. Carefully pierce through the overlay above each contro! panel hole that you have marked. Cut out material covering the pre-drilled holes with the razor knife. Be sure to cut the background overlay above each hole and trim cleanly and evenly.

FUNCTION LABELS OVERLAY

Line up the supplied function labels with the corresponding control panel holes. Remove the. backing and carefully press into place. Be sure they are straight. Attach the HOOK/SWING reference diagram above the trackball label. If your control panel is too narrow to fit the reference diagram, mount the diagram under the monitor glass on the bezel. Refer to the diagrams below.

HOOK / SWING Reference Overtay TRACHEAL OVERLAY

FACEUT FASE moAT Se "Sonata

FUNCTION LABEL LAYOUT #1

or put the HOOK/SWING Reference diagram on the bezel

FUNCTION LABEL LAYOUT #2

Page 9

MARQUEE INSTALLATION

If your cabinet needs a new marquee glass, determine the correct size and cut the Plexiglas (supplied) to fit. Using the old marquee glass as‘a template, center the Plexiglas on your new marquee graphics, making sure that all the printed images will be visible. Using a razor knife, score the new marquee deeply, following the edges of the old glass. Carefully break of f the styrene. Be sure the light behind the marquee works and that the glass is clean on both sides. Now install the marquee graphics and glass securely.

REMEMBER! DO NOT WORK WITH ANY PART OF THIS SYSTEM PLUGGED IN (Lights, Monitor, or Power Supply).

NOTE: : All switch wires used in this game need to be wired to the normally open connection on the switches. Each switch requires a ground wire on the common connector and the appropriate. control or switch wire on the other normally open connector of the switch,

CONTROL PANEL ASSEMBLY

  • Install the trackball and buttons on the control panel by following the detailed instructions beginning on page 2. The two red buttons are used for FACE LEFT and FACE RIGHT, The white button is used as the START button. NOTE: If you want your new game to earn money, you must install the trackball correctly.
  • If you are using Plexiglas for added protection, don't forget to place it on the panel before inserting the buttons.
  • Wire the trackball and buttons using the JAMMA Harness Connection table on page 30. Connect the trackball using the supplied trackball cable into PLAYER 1 on the PCS. IMPORTANTI:

The supplied trackball comes equipped with a grounding cable. This cable must be connected to field ground to protect the trackball P.C. boards fram becaming damaged by electra-static discharge.

PRINTED CIRCUIT BOARD (PCB)

Mount the PCB to the side of the cabinet with the connector toward the top of the drawer. This will keep the wire harness from slipping off due to vibration. Mark and drill pilot holes (3/32") onto the cabinet side, being careful not to drill through to the outside. Attach the PCB standoffs to the cabinet using wood screws and Spacers, snug but not too tight or the board may warp or crack. Be sure the board is not being flexed in any way.

WIRE HARNESS

  • If youare installing GOLDEN TEE ‘97 into a Dynamo cabinet with a pre-installed JAMMA harness, you will notice that it does not have a wire for the test switch. You will have to add a contact to the edge connector at the proper position (position 15). Some cabinets (Dynamo included) have only one coin switch input and the coin switches are wired together. Connect the designated wires to the coin switches separately.
  • Attach the wire harness connector to the PCB. Be sure it is mounted correctly.
WARNING!!!

Make sure you have identified PIN 1 on the connector before powering up. Plugging the JAMMA connector in backwards will cause damage to the PCB.

GOLDEN TEE 3D GOLF - 7

Page 10
  • It is best to use cohnectors (not supplied) whenever joining a set of harness wires toa subassembly. If you choose to solder wires together, follow this procedure:
  • Strip off about 3" of insulation from the wire. ¢ Slide a piece of heat-shrink tubing over the end. © Do not leave a lot of excess wire spooled up in your cabinet. Cut the wires to the length you need plus a few extra inches. Leave enough for proper cable dressing. Do not make it stretch across the inside of the cabinet. Solder the new wire to the original wire. Use a straight in-line splice.

POWER WIRES

1. Connect the wires that are designated for your power supply. You will need a supply of +5 vde, and +12 vde. The +5 vde must be regulated to within 5% (+ or - 0.25). The +12 vde may be unregulated but should not stray too far or the sound may be affected. If the cabinet’s supply does not provide these voltages, it will have to be replaced. A switching-type supply is recommended. You will notice that you have more than one wire for each voltage. Use ail wires supplied on the harness. This will ensure better power transmission and prevent overloading of the edge connector pads. Tin all power supply wires before connecting them to the power supply. Loose strands may short out the supply. For best results, connect spade lugs to the ends of the power wires and attach to the screw terminals of the power supply.

MONITOR WIRES

You will be connecting the RED, GREEN, and BLUE video drives along with the composite SYNC and video GROUND wires.

8 - GOLDEN TEE 3D GOLF

SPEAKER WIRES

Connect the speaker wires paying attention to their polarity. [ NOTE:

If your cabinet has two speakers, connect both, Tf they are 8 or 16 ohm speakers, connect them in parallel, if they are 4 ohm, connect them in series.

NOTE: Examine the speaker carefully. Is it really up to the high standards you wish to maintain at your location? Unfortunately, many arcade speakers: are inadequate for reproduction of good game sounds. Remember, this is not just a video game —it is a video/audio game investment. Far more effort was put into the sounds of this game than is put into most other arcade games. If the speakers are not up to it, replace them. A small investment in good speakers can make a world of difference in profits. Competent and reasonably priced speakers can be obtained from stores such as Radio Shack,

Position speakers as far from the monitor as possible. If placed too close, the speaker's magnet may deflect the monitor and cause strange coloration, which can usually be corrected by degaussing the monitor. Make sure everything else in the cabinet is attached securely for the same reason.

SYNC

This is the recommended approach for a Weils- Gardener monitor and should work with some others as well.

If your monitor does not have a composite SYNC input but has separate horizontal and vertical SYNC inputs, try connecting the composite SYNC signal from the PCB to the negative horizontal SYNC signal on the monitor. This should produce a satisfactory result, although some adjustment of the monitor's SYNC contrals may be necessary.

Page 11

COIN Doors, TEST SWITCH,

SERVICE BUTTON, AND VOLUME CONTROL PANEL

  • Wire the coin doors and the test / service switch(es) as per the JAMMA Harness Connection table on page 30.
  • Connect the door lamps to the +12 vde supply. Some games have separate power supply outputs for the lamps.
  • Install a test switch somewhere convenient inside the coin door area. This switch allows you to enter adjustables, run diagnostics, and see or clear audits. Make it readily accessible through the coin door. Wire it to the Test wire on the JAMMA Harness.
  • Install a service switch (not included) somewhere convenient inside the coin door area, This switch allows you to give credits to players without affecting the game's credit audits or coin meters. Example: A player puts in a coin and gets no credit, the operator can then push the service button and a credit is given to the player without affecting the game's audits and coin meter.
  • GOLDEN TEE 97 has the ability to adjust volume at any time during ¢ game. Install 2 push button switches (not included) inside the coin door for easy access. Connect the switches to the JAMMA harness. Refer to the JAMMA Harness Connection diagram on page 30.
  • GOLDEN TEE '97 is also capable of running a Mars Light or other external signal, which will be activated if the game is running a special Hole-In-One contest.

MARS LIGHT Hookup

Equipment required: A MARS light police beacon and a 3 amp 120 volt AC solid state relay with a 2.5 to 8 volt control line.

1, Connect a wire from PIN 2 of the sound boards ticket connector to the positive. control line of the relay.

  • Connect a wire from PIN 3 of the sound beards ticket connector to the negative control line of the relay.
  • The hot AC line in should connect to one side of the light and the return should connect to the AC input of the relay.
  • From the AC output of the relay, connect a wire to the other side of the light.
  • The hole-in-one contest is turned on in the Operator Adjustables in order for the light to activate when a hole-in-one is made,
NOTE:

Mars Light will only work for sound PROMS 1.0 and above.

FINAL CHECK

1, Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware.

  • Make sure the coin door is tight and the coin mechs are well adjusted.
  • Make sure all assemblies are firmly attached. Anything that is not mounted securely will rattle when the game is played. This game makes use of low-frequency sounds which can cause any loose joints to rattle.

GOLDEN TEE 3D GOLF - 9

Page 12

INITIAL START-UP

  • Attach JAMMA Harness. Plug in the game and turn it on,
WARNING!

Make sure the harness is plugged in correctly. Damage to PCB will occur if JAMMA connector is plugged in wrong.

  • Look and smell for smoke (TURN IT OFF IMMEDIATELY IF ANY IS NOTICED).
NOTE: Use the Voltage Test screen té adjust your power supply. When the screen says “Voltage OK", your power supply is properly adjusted to 5.2 volts on the PCB, Adjust the +5 Voit supply so that you read 5.2 Volts across an I.C. on the circuit board. If measured at the power supply, the reading will be higher at the power supply outputs.
  • Make sure the green and yellow LED on the PCB is flashing. If not, something is wrong, turn off the game.
  • Listen for sound. Sounds should be heard in the attract mode.
  • If you do not hear any sounds and the yellow LED is flashing, try turning up the volume and check the speaker connections. Dropping a coin through a coin switch should cause a sound.
  • How is the picture? Is it centered or is it too bright or too Is it in focus? Adjust your monitor to get the best picture possible.
NOTE:

Check your monitor manual to make adjustments. Some test patterns are available through the

  • | game's system tests by pressing the Test switch. Use them when making any adjustments. (See SYSTEM TESTS information on page 19. Proper monitor adjustment is very important.)
  • Try all coin switches. Drop quarters or tokens through to check the coin mechs. Make sure the game is adding credits. You can use the Player Control Tests by pressing the test switch and entering the SYSTEM TEST MENU. Do all of the controls work? Try playing the game with the volume up and listen for rattling as you play. Tighten anything that is making noise.
  • Upon initial power-up, the game will initialize to factory default settings. These settings affect game elements such as number of credits per coin, difficulty settings, etc. The OPERATOR ADJUSTABLES MODE section will describe how to alter these settings and view the system audits or run system tests.

DIP SWITCH SETTINGS

The main dip switches can be found on the PCB near the JAMMA (SW1).

Dip switch 4 (ON): Always “ON” (DEFAULT) Dip switch 4 (OFF): | *** NOT USED *** Dip switch 3(ON): Trackball normal (DEFAULT) Dip switch 3 (OFF): Trackball mounted at 45° angie Dip switch 2(ON): One Trackball (DEFAULT) Dip switch 2 (OFF): Two Trackballs Dip switch 1 (ON): Normal Game Play (DEFAULT) Dip switch 1 (OFF): © Operator Mode Menu

There are also dip switches near the green LED (SW2), Switches #1 and #2 must be “ON“ and switches #3 and #4 should be “OFF”.

10 - GOLDEN TEE 3D GOLF

Page 13

OPERATOR MODE

To enter the OPERATOR MODE MENU, press the Test Button, located just inside the coin door. When the Test Button is pressed or DIP Switch 1 is flipped on SW1 to the “OFF” position, the screen displays the OPERA TOR MODE MENU.

NOTE:

Tf you used DIP switch 1 to enter the OPERATOR MODE MENY, you will need to flip DIP switch 1 back to the ON position in order to Feturn to the game.

OPERATOR MODE MENU

The OPERATOR MODE MENU allows you to enter into four different areas:

VOLUME SETTINGS is used to adjust the volume of your game for your location,

OPERATOR ADJUSTABLES is used for customizing your game for your location. Some of the features in Operator Adjustables are number of coins per game, sounds on or of f when no one is playing, difficulty settings, etc. GAME AUDITS allows you to check your game's overall earnings, game times, game scores, etc. The Audits can be reset through this menu as well.

LEADERBOARD MENU is used to display or clear

the players names that are posted during a given tournament.

SYSTEM TESTS verifies the operation of the hardware, controls, and monitor through easy and automatic procedures accessed through these menus.

NOTE:

You can access a comprehensive “Quick Test" by holding down the START button while powering up the game. The test will automatically run through the various board tests, and end at the player control test. This is a quick way to test the integrity of your PCB and software.

Menu items can be highlighted using the trackball or FACE LEFT and FACE RIGHT buttons. When using the trackball, menu items are highlighted by rolling the trackball up or down. To select a highlighted item, press the START button.

To exit any of these tests and return the game to its normal state, use the trackball or FACE LEFT and FACE RIGHT button to highlight the line that says EXIT, and press the START button.

COLOR KEY NOTE:

For easy identification, all test screens have been color coded. Items displayed in GREEN are the Menu titles. This is the name of the menu that is currently displayed. Ttems appearing in YELLOW are the menu's instructions. The BLUE items are choices available in this menu. The WHITE item is the selection that is currently highlighted. If RED is ever displayed, there is a problem with that item and it should be corrected.

SS

GOLDEN TEE 3D GOLF - 11

Page 14

Oy oe

The VOLUME SETTINGS screen is used to adjust the sounds that are heard during game play. The OPERATOR ADJUSTABLES MENU is accessed through the OPERATOR MODE MENU. From the OPERATOR MODE MENU. roll the trackball down or up to highlight the words - OPERATOR ADJUSTABLES MENU which will ; then appear in purple letters. Now press the START button, and the OPERATOR ADJUSTABLES MENt/will appear on the screen. = a STARE

VOLUME SETTINGS SCREEN

When this screen appears, music will play. Move the trackball to the right to increase the game's sounds and music. Rolling the trackball to the left will make the game sounds softer. When you have. adjusted the sounds to the appropriate volume, press the START button to exit back to the main menu.

The volume can also be set using optional volume up/down push button switches. See page 8 for more information on this feature.

OPERATOR ALJUSTABLES MENU

As you can see, there are many possible customizing procedures that you can control. Below is a brief description of each adjustable function and what the screen looks like when displayed. Remember, to select an item from any menu, using the trackball to highlight the item in purple, and then press the START button. '

LS 12 - GOLDEN TEE 3D GOLF

Page 15

%

GAME MODE SELECTION

This menu allows you to place the game in standard Coin Mode, or choose Free Play.

GAME MODE SELECTION SCREEN

In COIN MODE, the game will only work if coins are deposited into the game.

In FREE PLAY, coins are not needed for play, and the START button is always active.

GAME RESETS

The GAME RESETS menu will cancel or zero out any custom features or bookkeeping figures that are no longer wanted.

AME RESETS MENU

RESET ALL TO FACTORY SETTINGS will change the game back to the way the game was preset when new. Any custom features such as Free Play and Skill Levels will be changed back to the original settings set at the factory.

RESET HIGH SCORES ONLY is used to erase all of the high scores stored in memory.

RESET AUDITS ONLY is used when all of your bookkeeping and statistics have been gathered from the Audits section, and are no longer needed. If you like to gather all of your accounting information each week, or after each collection, it is a good practice to reset all of the audits so your coin count will match the audit information.

ATTRACT MODE SOUNDS

This menu is used to adjust the sounds that are heard while no one is playing the game.

GOLDEN TER”

ATTRACT MODE SOUNDS MENU

ALL ATTRACT MODE SOUNDS ON will play sounds during every attract cycle.

OCCASIONAL ATTRACT MODE SOUNDS plays sounds about every ten to twelve times the attract mode is repeated.

ALL ATTRACT MODE SOUNDS OFF will not allow any sounds to be played during the attract mode.

GOLDEN TEE 3b GOLF - 13

Page 16

CREDITS AND COIN DOOR

SETTINGS

This menu allows you to change the number of coins needed to play GOLDEN TEE '97.

CREDIT AND COIN DOOR SETTING SCREEN

You can set each door to différent coins values by highlighting: DOOR 1 COIN VALUE for coin door 1, DOOR 2 COIN VALUE for coin door 2, etc., Moving Trackball left or right will change the number of credits that each coin represents.

COINS NEEDED FOR ONE CREDIT..... To award a game credit, the player will need to insert an adjustable number of coins.

HOLES PLAYED PER CREDIT..... This defines the number of holes the player is given for each credit. This value can range from 1 to 3 holes.

COINS NEEDED TO PLAY 18 HOLES..... To play an entire 18 holes at a reduced cost to the player, you can set this value to something less than the cost of buying holes as described above. The default is 10 coins for 18 holes, This is a savings of 2 coins, at a rate of 2 coins for 3 holes. The piayer will need to insert ali 10 coins at the start of a game to take advantage of this. DELAY TIME ADJUSTMENT

This option allows for changing the delay of game time.

OLDEN TREAT E06

BUTTON CONFIGURATIONS SCREEN.

DELAY OF GAME TIMEOUT (1)..... The game will give the player a penalty stroke if they have not swung the club after this amount of time.

DELAY OF GAME TIMEOUT (2)..... The timeout can be disabled by selecting "OFF" - The default is ON". We recommend leaving this "ON" so the game will return to the attract mode if a player walks away from a game in progress. After 3 successive timeouts the game will end for that player. This allows for players to drop out of three or four player games.

SS 14 - GOLDEN TEE 3D GOLF

Page 17

* SKILL LEVEL ADJUSTMENT

GOLDEN TEE '97 allows for changing the level of skill needed to play the game. This feature is good for locations with younger or novice player's who are less skilled at the game, or expert or accomplished players who demand a greater challenge.

SKILL LEVEL ADTUSTMENT SCREEN

To set the game to an easy skill level, highlight... SKILL LEVEL 1 - EASIEST. :

To set the game to a difficult skill level, highlight... SKILL LEVEL 5 - HARDEST.

SKILL LEVEL 2, SKILL LEVEL 3, and SKILL LEVEL 4 are settings between the easiest and hardest levels. Sometimes it is best if the skill level is adjusted gradually over a period of time.

HOLE IN ONE CONTEST MODE

The HOLE IN ONE CONTEST MODE can be used if your location wants to give away prizes for a holein-one.

"97 4.60 HOLE IN ONE CONTEST MODE SCREEN

Setting the HOLE-IN-ONE CONTEST "ON" will cause « loud siren and fanfare to go of f if a holein-one is made. The hole-in-one message can be altered depending on your type of contest.

NO HOLE IN ONE CONTEST will keep the fanfare and screen message OFF, if you are not running your own contest.

NOTE:

Tf you are not running your own contest, keep this item selected to OFF. Players become confused and disappointed if this mode is accidentally left ON.

HOLE IN ONE CONTEST - WIN IMMEDIATELY will display a “YOU HAVE WON“ message.

HOLE IN ONE CONTEST - QUALIFY TO WIN will display a “YOU HAVE QUALIFIED" message.

NOTE:

The fanfare lasts about 1 minute and 30 seconds. You can cancel the fanfare at any time by pressing START button.

GOLDEN TEE 3D GOLF - 15

Page 18

BS

COIN DOOR PROTECTION MENU

Golden Tee '97 comes equipped with software to help avoid coin stringing. If you wish to activate The GAME AUDITS MENU will supply you with a this software, highlight COIN DOOR detailed accounting of helpful and informative PROTECTION and move the trackball to the right bookkeeping and statistics. To enter the GAME until the word YES appears. The coin protection AUDITS MENU, first go to the OPERATOR MODE software is now activated. MENU by pressing the test switch located just inside the coin door of the cabinet or flip DIP switch 1 on SW1 to the OFF position on the PCB. From the OPERATOR MODE MENU, roll the trackball down or up to highlight the words GAME AUDITS MENU which will then appear in purple letters. Now press the START button, and the GAME AUDITS MENU will appear on the screen.

COIN DOOR PROTECTION is implemented by monitoring the coin switch pulse width. A pulse longer than the MAXIMUM PULSE WIDTH COUNT sets the game alarm counter. Each count represents about 4 milliseconds. GAME AUDETS SCREEN

If two game alarms occur then the game halts and . displays a coin failure message. Any unused DISPLAY COIN AUDITS credits in the game are cleared. When you choose to review the coin audits, the A count of good coin drops is kept and each time OISPLAY COIN AUDITS screen will appear. the GOOD COIN CLEAR COUNT is reached the game alarm counter is cleared. This allows an occasional coin switch glitch to be tolerated.

A count of all switch alarms for each coin door is also kept. These counters can be cleared by selecting RESET COIN DOOR ALARM COUNTS.

NOTE:

Coin mechanisms and bill acceptors vary widely. Test your game thoroughly with the coin protection ON to make sure the software is compatible with your hardware. DISPLAY COIN AUDITS SCREEN

16 - GOLDEN TEE 3D GOLF

ii Fi Sea ea TRA

Page 19

DISPLAY GAME SELECTION AUDITS PINE CREEK AUDITS _

This menu will show the audits for each game This menu displays the audits for the Pine Creek selection. course. BOARS VERRY 40

DISPLAY GAME SELECTION AUDITS SCREEN

PLINE CREEK AUDITS SCREEN _

NuMBER OF GOLFERS AND HOLES PLAYED CORAL RIDGE AUDITS

This menu displays how many games were played This menu displays the audits for the Coral Ridge by 1, 2, 3, or 4 players and how may holes were course, played during a game:

aman GOLDEN TEE 3D GOLF - 17

Page 20

RED SANDS AUDITS RESET AUDITS

This menu will display the audits for the Red This menu will reset your audits. Sands course.

RESET AUDITS SCREEN

If you wish to set all of the game audits (described above) back to zero, highlight RESET AUDITS from this menu and press the START button. The screen will briefly display AUDIT RESET.

a NDS AUDITS SRI . ED SANDS AUDITS SER If you change your mind and decide not to reset DISPLAY HARDWARE AUDITS the audits to zero, highlight NO RESET AUDITS and you will exit this screen without making any This screen displays the number of times the changes. voltage has read OK, Low, or High during the initial power-up or play of the game.

The factory default for Golden Tee '97 displays pre-set initials and scores on the leaderboard, which allows for a sense of competition and improvement to the player. If you are gaing to run your own league or tournaments, you may wish to delete these placeholders so only real players are displayed on the leaderboard.

LEADER BOARD MENU

Ta view the various course leaderboards, highlight DISPLAY LEADER BOARD MENU.

To clear all of the scores and names in the various course ieader boards, select CLEAR LEADER MENU.

i 18 - GOLDEN TEE 3D GOLF

ee

Page 21

DISPLAY LEADER BoaRD MENU

DISPLAY LEADERBAORD MENU

Select the course you wish to look at, and press the START button. The screen will stay on until you press START again to exit. You can use this information to determine your tournament or league winners. Great shot points have been included on this screen for use as tie breakers.

NOTE:

Great Shot Points gre not displayed during the game, so players may not be aware of their Great Shot Point total.

CLEAR LEADER BOARD MENU

CLEAR LEADERBAORD MENU

When selecting an in-house tournament, you should clear all of the names and scores from the course you wish to play on. Highlight the course leaderboard and press START. All of the initials and scores will be cleared, and the leaderboard will be empty. Players who complete an 18 hole course on the cleared course will have their statistics saved on the leaderboard until it is cleared again, GOLDEN TEE ‘97 has been inspected and tested at the factory, and most likely. the game will be in perfect working order when you plug it in. If you are experiencing any problems with the gate, the SYSTEM TESTS MENUis a good place to start when tracking down the problem. To enter the SYSTEM TESTS MENU, first go to the OPERA TOR MODE MENU by pressing the test ( switch located just inside the coin door of the cabinet, or set DIP Switch 1 on SW1 on the PCB { to the OFF position. From the OPERATOR MODE MENU roil the trackball up or down until the word SYSTEM TESTS MENU appears in purple letters. Now press the START button, and the SYSTEM TESTS MENU will appear on the screen.

SYSTEM TESTS MENU

re GOLDEN TEE 3B GOLF - 19 = Sete ra atcanccc as aa ceca LRN trac hum rca amermama ee rena HIPLIRICA HAD RN AANNAI RANA RERAEaRRIRRa RLEERRensReamuenssaNNAReRIseatemntaemmeentiicc: |

Page 22

*

VIDEO SCREEN TESTS

You can test your monitor and adjust colors by choosing VIDEO SCREEN TESTS and pressing the START button.

VIDEO SCREEN TEST MENU

When the FACE LEFT or FACE RIGHT buttons are pressed, the screen changes to display a grid of colored rectangles. Use these colors as a guide and adjust your monitor so they look as good as possible. This test can be exited at any time by pressing the START button.

FULL GROM CHECKSUM TEST

Choose FULL GROM CHECKSUM TEST from the SYSTEM TEST MENU to test the Graphics chips on the PCB. This test performs a complete test of the Graphics ROM's. While the test is in progress the following message is displayed:

FULL GROM CHECKSUM TEST SCREEN (TEST IN PROGRESS)

When the test is completed the GROM Test Screen is displayed.

PULL GROM CHECKSUM TEST SCREEN {TEST COMPLETED)

  • If all checksums are shown in blue, the test passed and your game is in good working order.
  • If any checksums are bad, they will be displayed in red text on this screen. This means that the GROM is defective and needs to be replaced. Call your distributor or the Incredible Technologies, Inc. Service Department for further help.
  • To exit this test, press the START button.

AS 20 - GOLDEN TEE 3B GOLF

Page 23

Fast GROM CHECKSUM TEST

Choose FAST GROM CHECKSUM TEST from the SYSTEM TEST MENU to test the Graphics chips on the PCB. This test performs a complete tést of the Graphics ROM’s. While the test is in progress the following message is displayed:

FAST GROM CHECKSUM SCREEN (FEST IN PROGRESS) When the test is completed the GROM Test Screen is displayed.

‘ST SCREEN

  • If all checksums are shown in white, the test passed and your game is in good working order.
  • If any checksums are bad, they will be displayed in red text on this screen. This means that the GROM is defective and needs to be replaced. Call your distributor or the Incredible Technologies, Inc. Service Department for further help.
  • To exit this test, press the START button. VIDEO RAM TEST

This test performs a complete test of the Graphics video RAM. The video RAM is tested in two pages. The following message will be displayed as each page is tested.

When the test is completed the results will be displayed as follows.

VIDEO RAM TEST SCREEN

  • If the game passes this test, zeros will be displayed in white along with a VIDEO RAM TEST PASSED message.
  • If the test fails, a non-zero status and VIDEO RAM TEST FAILED message will be displayed in red. Call your distributor or the Incredible Technologies, Inc. Service Department for further help.
  • To exit this test, press the START button.

PALETTE RAM TEST

PALETTE RAM TEST SCREEN

GOLDEN TEE 3D GOLF - 21

Page 24

BOARD TESTS

This test will perform ail of the system's tests at one time.

BOARD TESTS SCREEN

SOUND TESTS :

Choose SOUND TEST from the SYSTEM TEST MENU to test the sounds and speakers in the game. The sound section also controis the coin meter, and you can test it from this section as well.

SOUND TESTS SCREEN To test the coin meter, choose COIN METER TEST from this menu. If everything is working properly, the meter should increment each time the START button is pressed while this line is highlighted. CONTROL PANEL TEST

When CONTROL PANEL TESTis selected, the screen will display a diagram of a typical GOLDEN TEE ‘97 control panel. The controls are _ highlighted on the diagram when the controls are active. Test all of the controls, including coin test and service switches. Press FACE LEFT and FACE RIGHT together to exit this test.

CONTROL PANEL TEST SCREEN

NOTE:

For cabinets with 2 sets of player controls, two separate player control tests will appear in the SYSTEM TESTS MENU.

VOLTAGE ADJUST TEST

When the VOLTAGE ADJUST TEST is selected, the screen will display the history of how the voltage has been and how the current voltage is now. Adjust your voltage until you read voltage is OK.

VOLTAGE ADJUST TEST SCREEN

SS 22 - GOLDEN TEE 3D GOLF

Page 25

APPENDIX A -

GENERAL TROUBLESHOOTING

NOTE: ‘ The 5 Volt setting on the power supply must be set to 5.2 Volts on the circuit board (I.C.). Use the Voltage Adjust Test screen, on page 19, to help you adjust your power supply. When the test screen reads VOLTAGE OK, your power supply is properly adjusted.

IMPORTANTI: The supplied trackball comes equipped with a grounding cable. This cable must be connected to field ground to protect the trackball P.C. boards from becoming damaged by electro-static discharge.

SS 24 - GOLDEN TEE 3D GOLF

Page 26

DEC PRCBLE

Probable Cause. | —_ Solution | _ No picture Check Dip switches. SWL-Dip switches, 1 thru 4 must be “ONT,

SW2-Dip switches 1 and 2 must be ‘ON’, _ and 3 and 4 must be ‘OFF’

Bad connections Make sure there are good connections from the board's video outputs to the monitor's video inputs.

Monitor Make sure the monitor is operating correctly, (Check it with another compatible logic board.)

JAMMA harness connected Identify Pin 1 on the JAMMA connector improperly and on the PCB. Tf installed incorrectly, damage to the PCB may have occurred. Scrambled Picture _ Missing sync connection or Check the sync connection - Adjust misadjusted monitor monitor Missing colors or a washed out color Bad video connections Check the video red, green, and blue connections, _ Bright, blurry, or rolling picture. Misadjusted monitor Adjust the monitor, not the board. (Refer to your monitor manual.) Picture too large, too stnall, or of f center Misadjusted monitor Adjust the monitor, not the board. - (Refer to your monitor manual.) Video image is flipped Misadjusted Monitor Reverse the monitor's convergence wires or flip the monitor 180°. (Refer to your monitor manual.) Bad images in picture Bad GROM Do GROM test. Check IC pins to make sure none are bent over. Diagonal white lines GND problem Earth and Logic GND’s should be connected at the power supply.

GOLDEN TEE 3D GOLF - 25

Page 27

Se Sound | 412v power supply ig boat

Sad connection to the board

JAMMA harness connected improperly

Miscellaneous

26 - GOLDEN TEE 3D GOLF “Try another +12v power supply

Check for +22v power on tha: based,

Check for +5v power on the isarsi

Check the volume setting in the OPERATORS ADJUSTABLE section of the Operators Mode.

Check the speaker connections.

Identify Pin 1 on the JAMMA connector and on the PCB. If instatled incorrectly, damage to the PCB may have occurred.

Make sure the sound status light is flashing on the board.

Page 28

Buttons do not work or are partly inoperable. Or the selections keep scrolling on Operator Mode menus.

Coin counter not working

Trackball mounted correctly but is swinging 45° out of line.

Ina two or more player game, controls only work for players 2 and

Trackball does not work

IMPORTANT: Switches not property conriected

JAMMA harness connected improperly

Miscellaneous

SWI-Dip switch 3, found near the TJAMMA, is not "ON"

SW1-Dip switch 2, found near the JAMMA, is in the "OFF* position

No +5 voltage uke sure thot thecusion post of the awetch is connected to ground.

Make sure each individual switch is working by doing the Control Panel Test found in the SYSTEM TESTS section.

Make sure that the signal wire for that particular switch is connected to the normally open post of the switch.

Identify Pin 1 on the JAMMA connector and on the PCB. If installed incorrectly, damage to the PCB may have occurred,

Make sure that the signal wire has a connection from the switch to the board.

Make sure +12v is hooked up to the. counter.

The signal wire is not connected to coin counter. (Check continuity).

Verify that the counter is good.

Make sure SW1-Dip switch 3 is "ON".

SWL-Dip switch 2 must be in the "ON" position for cabinets with one set of player controls,

Bad inductor(L7) or bad connection to trackball,

The supplied trackball comes equipped with a grounding cable. This cable must be connected to field ground to protect the trackball P.C. boards from becoming damaged by electro-static discharge.

GOLDEN TEE 3D GOLF - 27?

Page 29

No reaction when game is turned on Valtage to high

No power from the power supply

Power supply

Short on the board

JAMMA harness connected improperly

Screen flashes repeatedly Open on socketed IC's

+5v setting too low

SW2 Dip switches near the green LED may not be set correctly.

el 28 - GOLDEN TEE 3D GOLF ssapusiksassbocauatauisaitpowanacistseecasaakasasiectaqasgunawueaaacesebesaeresus eeu eaNpiisg ace MURb MUR DANCER UL UCU IEICE a aes cee i inal sais lular east asuaaraL a aanRaRANTSTEIUNRIY Power supply is too highs Pamersteaalel ber between +5v &5.2v. (Measured on the circuit board).

Cabinet is not connected to earth ground. {All metal should be connected to the earth ground).

Short between power and ground. Check for foreign material,

Disconnect the harness and measure the resistance between power and ground. It should read around 600 ohms. (0 ohms is a dead short),

Make sure the harness is not shorting to anything, such as bare or frayed wires shorting out each other or hitting bare metal.

Replace power supply.

Power supply too low. (Should ideally be between +5v & +5.2v), (Measured on the. circuit board).

Check for loose or foreign material on the board.

Tdentify Pin 1on the JAMMA connector and on the PCB. Tf installed incorrectly, damage to the PCB may have occurred.

Check for bent pins on socketed parts.

Make sure that all IC's are seated in their sockets property.

Check voltage. (Measured on the circuit board).

Make sure SW2-Dip switch #1 and # 2 are “ON*, and #3 and #4 are “OFF”.

Page 30

Green L.E.D. not blinking

Operator adjustables keep changing

Sounds bad

Game comes up in Test Mode.

Trackball mounted correctly but is swinging 45° out of line. ‘ Program not running

Bad connections

Loose pin on ASIC (U1)

Low battery voltage

Bad static RAM (U50)

Miscellaneous

Dip Switch 1 is “OFF"

SWL-Dip switches are not all "ON". Make sure all socketed I.C.'s are seated correctly. Look for bent pins.

Make sure you have continuity from PCB to power supply.

Call Incredible Technologies, Inc.

Battery should be 2 to 3 volts.

Replace.

Check the speaker connections.

Make sure SWI-Dip Switch 1, near the TAMMA, is in the “ON" position.

Make sure the SW1-Dip switches are all *ON*.

GOLDEN TEE 3D GOLF - 29

Page 31

APPENDIX B

| JAMMA HARNESS CONNECTION

30 - GOLDEN TEE 3D GOLF

Page 32

eo a oe > cS ke Re

xa Se me Se

es

Player Face Left Yellow-White - Orange-Yellow Volume Down Volume Up Orange-White

Memory Board Connector Trackball Connector PIN WIRE #6 - Black PIN WIRE #1 - Black

PIN WIRE #1 - Red PIN WIRE #2 - Red

PIN WIRE #2 - Yellow @ PIN WIRE #3 - Yellow PIN WIRE #3 - Green E PIN WIRE #4 - Green PIN WIRE #5 - Blue ! PIN WIRE #6 - Blue

PIN WIRE #4 - Purple PIN WIRE #6 - Purple

NOTE: REMEMBER TO CONNECT THE TRACKBALL CABLE TO JP7. ~

GOLDEN TEE 3D GOLF - 31

Page 33

APPENDIX C

1/O and JAMMA SCHEMATIC |

32 - GOLDEN TEE 3D GOLF

Page 34

GOLDEN TEE 3b GOLF -

Page 35

APPENDIX D

WARRANTY INFORMATION

34 - GOLDEN TEE 3D GOLF

Page 36

TECHNOLOCIES

If the original purchaser discovers any physical defect in the media (disk, EPROM, tape) on which the software is distributed or in the documentation, which in the opinion of Incredible Technologies, Inc. (IT) prevents the product from being used as reasonably intended, IT will replace the media or documentation at no charge. The purchaser must return the item to be replaced, with proof of purchase, to IT within 90 days after taking delivery of the software. IT warrants to the original purchaser that the hardware product is in good working condition for a period of 90 days from taking delivery of the product. Should this product, in IT's opinion, malfunction within the warranty period because of a defect in design, materials, or workmanship, IT will repair or replace this product without charge under the terms as follows. Replacement of either the hardware product or its component parts will be only on an exchange basis. Any replaced parts or components become the property of IT. This warranty does not apply to those products which have been damaged due to accident, abuse, improper installation, natural disaster, or unauthorized repairs or modifications. IT excludes any and all implied warranties, including warranties of merchantability and fitness for a particular purpose, and limits the purchaser's remedy to returning the software, hardware, or documentation to IT for replacement. IT makes no warranty or representation, either express or implied, with respect to this software, hardware, or documentation, their quality, performance, merchantability, or fitness for a particular purpose. This software, hardware, and documentation are licensed “as is," and the purchaser/licensee assumes the entire risk as to their quality and performance. In no event will IT be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the software, hardware, or documentation, even if advised of the possibility of such damages. The warranty and remedies set forth above are exclusive and in lieu of all others, oral or written, express or implied. No person, seller, dealer, agent, or employee is authorized to make any modification or addition to this limited warranty. Some states do not allow the exclusion of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

~ INCREDIBLE TECHNOLOGIES, INC. 02/97

eS GOLDEN TEE 3b GOLF - 35

Page 37

* INCREDIBLE TECHNOLOGIES, INC. | - SERVICE / SALES (800) 262-0323 FAX (847) 870-0120 Hardware and Software ©Copyright 1997 Incredible Technologies, Inc. All rights reserved. | a

Page 38

1 Incredible Technologies, Inc. 4010 Winnetka Avenue

Rolling Meadows, IL 60008

(847) 870-7027 + (847) 870-0120 FAX Attp://www.itsgames.com