CATHODE RAY TOMES

Pool Shark TM-083 1st Printing

Poolshark (Atari, 1977) · Technical Manual · 60 pages · 21 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

WARRANTY

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller’s other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER’S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 3

ATARI INC. 1265 BORREGAS AVENUE SUNNYVALE, CALIFORNIA 94086 408/745-2000 # TELEX 35-7488 Poobshankiiii)

Operation, Maintenance and Service Manual

By the Publications Group, Engineering Department AM

ATARI

©: Warner Communications Company

Page 4

All rights reserved. Copyright © 1977 by Atari, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

For permission requests, write:

PUBLICATIONS GROUP. ATARI INC. 1265 BORREGAS AVENUE P.O. BOX 9027 SUNNYVALE, CA 94086

6F

Lithographed in the U.S.A.

Page 5

TABLE OF CONTENTS

1 maa aeeTES SETUP WHY YOU SHOULD READ THIS CHAPTER . GAME INSPECTION INSTALLATION REQUIREMENTS FOR POOLSHARK INTERLOCK AND POWER ON/OFF SWITCHES SELF-TEST PROCEDURE IN TABLE 1 OPERATOR OPTIONS

2 GAME PLAY ATTRACT MODE READY-TO-PLAY MODE PLAY MODE ... SELF-TEST MODE ..

3 MAINTENANCE AND ADJUSTMENTS CLEANING COIN MECHANISM .. Components on Coin Door ... Access to Coin Mechanisms ... Cleaning of Coin Paths ..... Adjustment of Coin Switch Trip Wire .. Mechanical Adjustments of Coin Mechanism General Troubleshooting Hints ..... 16 ADJUSTMENTS ON TV MONITOR TV MONITOR REMOVAL ...... FUSE REPLACEMENT ... LAMP REPLACEMENT . START SWITCHES on JOYSTICKS occ center ete eee erent eee

4 _BHEORY OF OPERATION POOLSHARK GAME OVERVIEW mmOOR> NER KNO

CaP >

>

ZOA™™OA

a POOLSHARK PCB OPERATION ... Poolshark PCB Overview C. POOLSHARK PCB POWER .. 29 D. POOLSHARK MICROCOMPUTER . 29 E. MICROCOMPUTER INTERFACE . Motion Circuit Switch Distribution Circuit Score/Playfield Circuit Sound Circuits Lamp Circuits Joystick Circuits

Page 6

LIST OF ILLUSTRATIONS

Figure 7 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 17 Figure 12 Figure 13 Figure 14 Figure 15 Figure 16 Figure 17 Figure 18 Figure 19 Figure 20 Figure 21 Figure 22 Figure 23 Figure 24 Locations of On/Off, Interlock, and Self-Test Switches .. 7 Removal of Poolshark PCB and Location of Switches and Alignment Pots 8 Attract Mode TV Monitor Picture Ready-to-Play Mode TV Monitor Picture Play Mode TV Monitor Picture ... Coin Door Assembly ........... Hinging Open the Magnet Gate Assembly ... Removal of Coin Mechanism Surfaces to Clean Inside the Coin Mechanism Removal of Plate Covering Rear of Coin Slot . Close-Up View of Lubrication Point Detail View of Coin Switch and Trip Wire Adjustments on Coin Mechanism ..... Locations of Adjustments on TV Chassis . Removal of TV Monitor ......... Removal of Fluorescent Lamp ... Harness Wire Connections on START Switches ... Removal of Joysticks Cleaning Potentiometers with Tuner Cleaner . Poolshark Game Block Diagram ..........+055 Poolshark PCB Block Diagram :.. Poolshark Printed Circuit Board Schematic Diagram (Sheets 1-6) . Oscilloscope Picture of 01, 02, and CLOCK ..

LIST OF TABLES

Table 1 Table 2 Table 3 able 3 Table 4 Self-Test Procedure Optional Settings oF Switch Ston Poolshark PCB .. Aid for Locating ure 22... Definitions of Schematic Signal Nomenclature

Page 7

WHAT IS POOLSHARK?

Poolshark™ is an Atari game that simulates the game of pocket pool, no pun intended, on a 23” TV monitor. This game has a self-test feature that tests approximately 75% of its internal circuitry. We hope the game earns you lots of money.

Page 8

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 9

LOCATION SETUP

A. WHY YOU SHOULD READ THIS CHAPTER Your new Poolshark™ is manufactured by Atari with the intent of being ready to play right out of the shipping carton. However, since we cannot be sure that the shipper delivered Poolshark to you in one piece, we need your cooperation in supplying the last touch of quality control. Therefore, we at Atari would appreciate your following the procedures of this chapter to ensure that you are getting the quality of game that you expect from Atari.

Page 10

B. GAME INSPECTION

External Parts of Game Cabinet: Check the outside of the game cabinet for dents, chips, or broken parts. If you have purchased this game as anew game, make sure that it looks new.

Internal Parts of Game Cabinet: Unlock and open the rear access door. Check the inside of the game cabinet for anything that looks out of place or broken.

C. INSTALLATION

REQUIREMENTS FOR

POOLSHARK

All special requirements for the installation of Poolshark are listed as follows:

Power Requirements: Atari ships Poolshark for the domestic operation on 110 VAC, rated at approximately 150 watts. The game can be changed to operate at 95 VAC by unplugging the Molex connector plug with orange wires (110 VAC) and plugging on the Molex connector plug with black wires (95 VAC).

Temperature Range: Location and storage temperature ranges should be no lower than 0 degrees centigrade (32 degrees fahrenheit) to no higher than 49 degrees centigrade (120 degrees fahrenheit).

Humidity Range: Location and storage relative humidity should be no more than 80%.

Location Space Utilization: Poolshark requires a minimum of 166 centimeters (65.25 inches) ofvertical clearance, a minimum of 64 centimeters (25.25 inches) of width clearance, and 135 centimeters (53 inches) of depthclearance. Depth clearance includes 61 centimeters (24 inches) of minimum player space.

Length and Type of Power Cord: Atari has added a 1.83-meter (six-foot) strain relief power cord to Poolshark. The advantage of the strain relief cord is that if someone trips over the cord, the cord will break off just inside the game. Someone tripping over a non-strain relief cord may result in ripping out the insides of a game. D. INTERLOCK AND POWER ON/OFF SWITCHES Atari had two concerns that resulted in our installing two on/off switches, as illustrated in Figure 1. The first concern was to minimize the hazard of electrical shock while you are working inside the game cabinet. Therefore, we installed an interlock switch on the rear access door that completely removes power from the game when the rear access door is open.

Our second concern was energy conservation. A power on/off switch has been added to Poolshark so that the game can be turned off during low business periods and closing hours. This switch is conveniently hidden beneath the right-hand corner of the protruding section on the front of the game cabinet.

Please check for the proper operation of the rear access interlock switch by performing the following:

  • Unlock and open the rear access door.
  • Plug the AC power cord into a 110-volt source.
  • Set the power on/off switch to the on position by flipping the toggle switch toward the front of the game cabinet.
  • Close the rear access door. Within approximately thirty seconds, the TV monitor should display a picture.
  • Slowly open the rear access door until the TV monitor picture disappears. The TV monitor picture should disappear when the rear access door is -opened to less than one-inch at the top of the door.
  • Close and lock the rear access door. If the results of Step 5 are OK, then the interlock switch is operating properly. If not OK, check to see if switch is broken from its mounting or stuck in the on position.

E. SELF-TEST PROCEDURE IN TABLE 1 Poolshark will test itself and provide data to communicate with you that the game's circuitry and controls are or are not operating properly. We suggest that you do the Poolshark Self-Test Procedure each time you collect the money from the game. All you need to do is follow Table 1. But first, please read the following explanation of the table.

Page 11

SWITCH TEST SWITCH INTERLOCK SWITCH

Figure 1 Locations of On/Off, Interlock, and Self-Test Switches

Notice the three column headings of Table 1. The first column, Operator Action, describes what you should do to make Poolshark test itself. Once you have performed each Operator Action Step, look at the picture on the Poolshark TV monitor and match that picture with the picture in the column labeled Poolshark TV Monitor Picture. Then, read the definition of that picture and follow the instructions listed in the column labeled Definition of TV Monitor Picture. Please note that Step 1’s third column is quite long. Refer to Figure 1 for location of the self-test switch. If af any time you would like to start over again in the self-test mode, just set the self-test switch to off, then again to the on position. This will begin the self-test mode at Step 1.

  • Unlock and remove rear access door.
  • Locate RF shield in lower right-hand corner.
  • Remove five #6 x ¥2-inch small pan-head Phillips screws from each of the long sides (total ten) of the R.F. Box Assembly.
Page 12

Table 1 Self-Test Procedure

Operator Action POOLSHARK TV Monitor Picture a Definition of TV Monitor Picture

Note: Poolshark will not go into the self-test mode if there is game credit or if the game is in the play mode.

Step 1 Set self-test switch to on position. Refer to Figure 1 for location of self-test switch. Test OK Por pr ALIGNED PUSH START 2

Pa

mista,

<

or TEST B or TEST C orTESTD or TEST E or TEST F

TEST OK POT PINOTATIGNID

< Test OK— Indicates that computer memory of Poolshark is operating properly.

POT P1 Indicates that left player’s cue ball ALIGNED— joystick x axis (left/right direction) circuit is properly adjusted.

PUSH START 2— Indicates that you should continue self-test, as stated in Operator Action Step 2.

TESTA or TEST B or TEST C or TEST D or TEST E or TEST F Indicates that the computer memory of Poolshark if failing. If this test failure occurs, we suggest that you note the failure and immediately contact your distributor. To solve this problem, you will need special replacement parts, available only through your distributor. The following is a list of failing circuits that relate to the failure indication of the Poolshark picture.

IC for -02 Poolshark PCB IC for -01 Poolshark PCB Test Failure

TESTA PI Pl TEST B NI NI

TEST CAl and/or E1KI
Test DBl andPor F1KI
TESTECl and/or H1ui
TEST FD1 and/or J1ui

POT P1 NOT ALIGNED— Indicates that left player’s joystick x axis (left/right direction) circuit is not properly adjusted. During game play, this problem will cause the cue ball to move without the player’s command. Before doing anything, tap the left player’s cue ball joystick. lf TV monitor pictures changes to POT P1 ALIGNED PUSH START 2 alignment of POT P1 is OK. However, it is best to determine if the springs of the joystick are worn. To do so, apply sideways pressure in one direction, then the other, to the joystick. You should feel an obvious center position to the joystick. The joystick should snap to its center

Page 13

Table 1 Self-Test Procedure

POOLSHARK TV Monitor Picture Operator Action Definition of TV Monitor Picture

position if moved in one direction and then let loose. If this obvious center position does not exist, call your distributor and arrange for the installation of a new joystick.

If there is an obvious center position and the TV monitor picture still indicates POT P1 NOT ALIGNED you need to remove the Poolshark PCB and adjust potentiometer P1.

NOTE: One of the major expenses of Poolshark is the PCB. If you do not have electronic hardware training, do not attempt to remove the PCB. Instead, contact your distributor. The mistake you make may cost you a good deal of money from downtime and repair costs.

Refer to Figure 2 for detailed information for the removal of Poolshark PCB and the location of POT P1, POT P2, POT P3, and POT P4.

Step 2 POT P2 Indicates that left player's cue ball joystick Press right player's ist ox ALIGNED— y axis (up/down direction) circuit is START pushbutton. PDUSH START properly aligned.

PUSH START 2—-Indicates that you should continue self-test, as stated in Operator Action Step 3.

POT P2 NOT Indicates that left player's joystick y axis ALIGNED— (up/down direction) circuitis not adjusted properly. Refer to previous instructions for POT P1 NOT ALIGNED. Remember that you are working with the up/down motion of the left player's joystick. Test Ok POT P2 NOT ALIGNED,

<

Step 3 Press right player's START pushbutton. POT P3. Indicates that right player’s cue ball ALIGNED— joystick x axis (left/right direction) circuit is operating properly. Tes OK POL PPALIGNLD

PUSH START 2

PUSH START 2—Indicates that you should continue self-test, as stated in Operator Action Step 4. —___l___ |

Page 14

Table 1 Self-Test Procedure

Operator Action POOISHARK

L TV Monitor Picture

Definition of TV Monitor Picture

POTHENOT ATIGNLD

<_ POT P3 NOT ALIGNED-— Indicates that right player's joystick x axis (left/right direction) circuit is not properly adjusted. Refer to previous instructions for POT P1 NOT ALIGNED. Remember that you are working with the left/right motion of the right player’s joystick.

Step 4 Press right player's START pushbutton. HS1 OW fOr pa ALTOS PUSH START 2 POT P4 ALIGNED—

PUSH START 2—- Indicates that right player’s cue ball joystick y axis (up/down direction) circuit is properly aligned.

Indicates that you should continue self-test, as stated in Operator Action Step 5.

ston POT PA NUT ALIGNID

<_ POT P4 NOT ALIGNED— Indicates that right player's joystick y axis (up/down direction) circuit is not adjusted properly. Refer to previous instructions for POT P1 NOT ALIGNED. Remember that you are working with the up/down motion of the right player's joystick,

Step 5 Press right player's START pushbutton. Test COMPLETE TEST COMPLETE— Indicates Poolshark has completed the video tests. Proceed with the switch tests in Steps 6 through 9.

—_}—__ Step 6 Press and momentarily hold left player's START pushbutton, then listen for sound that rapidly goes froma low toa high frequency. hist compute Audio sound indicates D-A LATCH circuit is operating properly.

Step 7 Press and momentarily hold right player’s START pushbutton, then listen for sound described in Step 6.

ee os HUST comutth Audio sound indicates D-A LATCH circuit is operating properly.

Page 15

Table 1 Self-Test Procedure

POOLSHARK Operator Action TV Monitor Picture \ Monitor Picture | Definition of TV Monitor Picture

Step 8 Press and momentarily hold left coin acceptor trip wire, then listen for sound described in Step 6. TeST COMPLEIL Audio sound indicated D-A LATCH circuit is operating properly.

Step 9 Press and momentarily hold right coin acceptor trip wire, then listen for sound described in Step 6. This completes the test and Poolshark is now ready to earn money. Set the selftest switch to the off position. TUS COMPLETE

  • Slip Poolshark PCB out of R.F. Box Assembly.
  • Ensure that the PCB is not touching metal sides of R.F. Box Assembly.
CAUTION Placing rear access interlock switch plunger in the defeat position results in the application of 110 VAC to Poolshark. Use extreme caution to prevent the hazard of electrical shock while working inside the game cabinet.
  • Defeat rear access interlock switch by pulling out on white switch plunger.
  • If alignment potentiometers were adjusted, set self-test switch to off, then back to on position. Recheck alignment of Steps 1 through 4 of Table 1.
  • Push the rear access interlock switch out of defeat position, then reinstall Poolshark PCB.
  • Close and lock rear access door. Audio sound indicates D-A LATCH circuit is operating properly.

F. OPERATOR OPTIONS At this time, it is best to select the game options best suited for your particular location. With the selftest switch set to the off position and Poolshark in the attract mode (no game credit), Poolshark may be set for the combinations of options you choose.

To set these options, refer to Figure 2 and remove Poolshark PCB. While the PCB is removed, determine if you would like to have extended play. Extended play works like this: if a player puts all the balls into the pockets within the thirty-second rack time, extended play will give him a new rack and fifteen seconds more time. Without extended play, after the player puts all the balls into the pockets, he gets a new rack. The player continues playing on the time of the rack during which all the balls were dropped. Extended play is selected by setting Toggle 1 of Switch $3 to the on or “+” position. Set toggles of Switch S1 to your choosing as determined from Table 2 as follows:

Page 16

aligning POTS.

NOTE

PL alignment 12 to correct P2 alignment 13 to correct P3 alignment 14 to correct Pa alignment Adjust potentiometer: 11 to correct POT

POT

POT

POT

Listen for audio hum sounds as an aid for

OPTIONAL,

Figure 2 Removal of Paolshark PCB and Location of Switches and Alignment Pots

Table 2 Optional Settings of Switch $1 on Poolshark PCB

Switch SI Toggle No. Video Picture of Racks Per Game | — Video Picture of Coins Per Game 1 2/3 |] 4

orr | OFF1COINEACH

OFF | ON 1COIN | -1GAME

ON | OFF1 COIN2 GAMES
ONON2 COINSLACH

OFF | OFF 2 RACK GAME OFF | ON 3 RACK GAME ON | OFF 4 RACK GAME ON ON i 3 RACK GAME

Note: The on position for Switch $1 is toward IC location 5.
Page 17

GAME PLAY

During use, Poolshark can be described as operating in four modes: attract, ready-to-play, play, or self-test.

A. ATTRACT MODE The attract mode begins with the application of power. During this mode, the TV monitor picture, as illustrated in Figure 3, shows a pool table set with a rack of balls and a cue ball. The TV monitor picture also shows the number of coins necessary for a game and the number of racks per game.

The only controls the game will respond to during this mode are the coin mechanism coin acceptors and the self-test switch. Depositing the proper numer of coins (as shown on the TV monitor picture) will cause the game to change to the ready-to-play mode. Setting the self-test switch to the on position will cause the game to change to the self-test mode. There is no sound during this mode.

Page 18

aren sat ae

Figure 3 Attract Mode TV Monitor Picture

Page 19

B. READY-TO-PLAY MODE The ready-to-play mode begins with the depositing of the necessary coins as indicated in the attract mode. During this mode, the TV monitor picture, as illustrated in Figure 4, ‘tells’ the player or players which START pushbutton to push. This statement replaces the GAME OVER statement of the attract mode. Otherwise the TV monitor picture of this mode is exactly the same as the attract mode. During this mode the coin acceptors will not accept any coins, the START pushbuttons are inactive (after being pushed to enter this mode), and the self-test switch has no effect. The sounds of this mode are “bump” when the bails strike the bumper boundary of the pool table, “score” when a ball drops into a pocket, ‘‘click’”’ when a ball hits another ball, and “scratch” sound when the cue ball drops into a pocket.

2 GaAnes

NOTE PUSH START 1 OR START 2 message line may read INSERT COIN; PUSH START 1OR IN- SERT COIN; PUSH START 2.

Figure 4 Ready-To-Play Mode TV Monitor Picture

Once the game enters this mode, it will not react to any controls other than the START pushbuttons. Pushing the appropriate START pushbutton will cause the game to change to the play mode. There is no sound during this mode.

C. PLAY MODE The play mode begins with a player pushing one of the two START pushbuttons. During this mode, the TV monitor picture, as illustrated in Figure 5, “tells” the player or players which joystick is presently active {arrow at bottom of picture points towards active joystick), how much time is left in the rack, and each player's score. Figure 5 Play Mode TV Monitor Picture

D. SELF-TEST MODE The self-test mode begins with the setting of the self-test switch to the on position. During this mode, the TV monitor pictures, as illustrated in Table 2 of Chapter 1, provide data to communicate with the operator that the game's circuitry and controls are or are not operating properly. This mode can only be entered from the attract mode.

Once this mode is entered, Poolshark’s self-test must be continued by the operator. This is done by you, the operator, pushing the START 2 pushbutton. At the end of the self-test procedure, the operator then has the responsibility of listening for a sound (same sound used for “‘score’’, as mentioned in Play Mode) while pressing the START pushbuttons and tripping the coin acceptors.

Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

Due to its solid-state electronic circuitry, this Atari game should require very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in the manual is intended to cover most servicing situations that may be encountered at the game site. The procedures given are in sufficient detail to be understood by a person with moderate technical ability.

  • NOTE if reading through the manual does not lead to solving the specific maintenance problem, you can reach Alati’s Customer Service Department by telephone (open Monday through Friday, 7:30 am to 4:30 pm Pacific Standard Time);

from outside California (800) 538-6892 (toll-free)

from inside California (408) 984-7900

For those interested in gaining more information on video game technology, especially the electronics, we recommend reading the Video Game Operator's Handbook, manual no. TM-043. This book is available from Atari, inc., attn. Customer Service Dept., 2175 Martin Avenue, Santa Clara, CA 95050 for $5.00 each, or from your distributor.

ADJUSTMENTS

Page 22

A. CLEANING The exteriors of game cabinets and plex panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from distributors. Do not dry-wipe the plex panels because any dust on the surface can scratch the surface and results in fogging the plastic.

B. COIN MECHANISM

Components On Coin Door Figure 6 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted. Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechs. During the attract mode the microcomputer energizes the lockout coil, causing the lock-out wires to retract far enough to allow genuine coins to reach the coin box. But during the ready-to-play mode when the LED is lighted and during the play mode (and also when AC power to the game has been turned off)

Slam Switch Assembly

Coin Lock-out Coil LAMP HOLDER

Figure 6 Coin Door Assembly the lock-out coil is de-energized, causing the lockout wires to move out far enough to divert coins over to the return chute.

Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire extending out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.

Also shown in the photograph is a slam switch assembly. It has been included to defeat any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.

Access To Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 7. Or, if necessary, each coin mechanism can be entirely removed from the door merely by pulling

Figure 7 Hinging Open the Magnet Gate Assembly

Page 23

back ona release lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 8.

Figure 8 Removal of Coin Mechanism

Cleaning of Coin Paths

CAUTION: The use of an abrasive (such as steel wool ora wire brush) or a lubrication on a coin mechanism will result in a rapid buildup of residue.

By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling wateranda mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air.

Figure 9 shows the surfaces to clean inside the coin mechanism. These include the inside surface of the mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnetitself. To remove these you can guide the point of a screwdriver or similar tool along the edge of the magnet.

If coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a %-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 10). Removing the plate will provide access to the entire channel. (Clean both surfaces where coin enters the mechanism, as well as the magnet)

Figure 9 Surfaces to Clean Inside the Coin Mechanism

Figure 10 Removal of Plate Covering Rear of Coin Slot

Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches.

LUBRICATION Lubrication. Do not apply lubrication to the coin mechanisms. The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 11 shows this lubrication point.

Page 24

Manually hold down rejection button and apply one drop here

Lock-out Wire

Figure 11 Close-up View of Lubrication Point

Adjustment of Coin Switch Trip Wire

In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of its trip wire should be as shown in Figure 12. Use extreme care when handling or touching these wires.

Mechanical Adjustments on Coin Mechanism

Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take it to a clean, well lighted area where it can be placed in a vertical position on a level surface (such as a bench top). Besides a screwdriver, you will need a set of several coins, including both new and old, worn ones. Figure 13 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These adjustments should only be igi by nme who has expe mechanisms and who understands their operation. Correctly adjusted trip wire

Figure 12 Detail View of Coin Switch and Trip Wire

General Troubleshooting Hints The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted. If troubles still persist, check the conditions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism rejects genuine coins, try to readjust it. If this is not successful, then replace it with a working mechanism.

C. ADJUSTMENTS ON TV MONITOR

NOTE The TV monitor is accessible only from inside the game cabinet and these adjustments have to be done while the game is energized. Therefore only persons familiar with safety measures and repair procedures on electrical equipment should perform them.
Page 25

ITEM IDENTIFICATIONS 1 Kicker and Separator Screws 2 Washers 3 Kicker 4 Separator 5 Gate Lever Spring 6 Gate Pivot Pin 7 Mainplate Assembly 8 “C” washer 9 Rail 10 Gate Assembly 12 Cradle Assembly

13 Upper Gate Pivot Spring 14 Undersize Lever Assembly 15 Magnet Gate Assembly 16 Magnet Gate Adjuster 17 Retaining Screws 18 Coverplate Assembly 19 Return Coverplate 20 Coverplat 21 Mounting Studs 22 Lower Gate Pivot Spring 23 Coin Release Lever

Kicker and separator

  • Set the acceptor with the back of the unit facing you in the test position.
  • Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws.
  • Insert several test coins (both old and new) and note that some are returned by striking the separator.
  • Loosen the separator screw and move the separator a slight amount to the left. Lightly retighten the screw.
  • Insert the test coins again and, if some are still returned, repeat Step 4 until all the coins are accepted.
  • Loosen the kicker screw and move the kicker as far to the left as it will go. Lightly retighten the screw.
  • Insert the test coins and note that some are returned.
  • Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw.
  • Insert the test coins again and, if some are still returned, repeat Step 8 until all the coins are accepted.
  • Be sure that both screws are tight after the adjustments have been made.

Magnet gate 1, Set the acceptor with the front of the unit facing you in the test position.

  • Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through.
  • With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate. 4, Test this adjustment using several other coins (both old and new) and, if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted.
  • Fix the magnet gate adjusting screw in this position with a drop of glue.
  • Remove the transfer cradle (12) and the undersize lever (14).
  • Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins.
  • Replace the transfer cradle and the undersize lever.
  • To be certain the coin mechanism is completely free of any residue, place the mechanism in a solution of boiling water and mild detergent for several minutes. Carefully remove it and let it air-dry completely before reinstalling in the door.

Figure 13. Adjustments on Coin Mechanism

Page 26

CONT BRITE FUSES VERT HORIZ HOLD HOLD VOL

Figure 14 Locations of Adjustments on TV Chassis

The TV monitor need be adjusted only when the picture is distorted, or if the contrast or brightness seem out of adjustment.

The monitor's adjustments function like those of a conventional commercial television set, except that the volume adjustment has no effect. Instead the game produces its sound in circuits separate from the TV monitor. Figure 14 shows the location of the adjustments on the rear of the chassis. When making the adjustments, follow these general guidelines:

BRITE (Brightness)—Perform this adjustment before the contrast. Adjust so that the white lines covering the screen just barely disappear, when the brightness is turned up. CONT (Contrast)—Adjust so that the images are as bright as possible against the dark background without being blurred. HORIZ HOLD (Horizontal Hold)—Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered picture. VERT HOLD (Vertical Hold)—This needs adjustment only if the picture appears to be rolling up or down the screen. Adjust for a stable, centered picture.

D. TV MONITOR REMOVAL If the TV monitor proves to be at fault, remove the monitor as shown in Figure 15.

E. FUSE REPLACEMENT Poolshark contains four fuses, two on the power supply assembly and two on the TV monitor assembly. These fuses are all easily accessible through the rear access door. Replace fuses only with the same type of fuse as follows:

TV Monitor Fuses 3AG 1-amp slow-blow, 250 volts Power Supply Fuses 3AG 2-amp slow-biow, 250 volts

F. LAMP REPLACEMENT Poolshark contains only two lamps, a type #47 incandescent lamp in the coin door and an eighteen-

Page 27

REMOVE UNPLUG MOLEX 4 MOUNTING CONNECTOR _ SCREWS (WOOD), FROM BACK “\_2 ON EACH SIDE OF MONITOR TSN CHASSIS

Figure 15 Removal of TV Monitor

inch fluorescent lamp inside the top of the game cabinet assembly. Refer to Figure 16 for instructions to replace the fluorescent lamp. To replace the coin door light bulb, remove the lamp holder mounting nut, replace the lamp, then remount the lamp holder (see Figure 6).

G. START SWITCHES There are two sets of identical game controls. These controls are both mounted on the front of the game cabinet directly in front of the TV monitor. The controls consist of two pushbutton switches and two joysticks.

The START pushbutton switches are backlighted by light-emitting diodes (LEDs). These switches generally have a low failure rate. Therefore, before changing one, make sure that the switch or LED is bad. To change a START pushbutton, unlock and open the coin mechanism door. Remove the wires from the defective switch. From the inside of the game cabinet, turn the switch counterclockwise while holding switch’s cone-shaped nut on outside of cabinet. Install new switch using the reverse procedure. Connect harness wires as shown in Figure 17.

H. JOYSTICKS The joysticks in Poolshark contain two potentiometers. The potentiometers are made with a carbon resistive material. Have you ever turned the volume up on a wellused radio and heard a static noise? That noise was the result of a worn carbon resistive volume control. What happens is that after turning the volume control up and down many times, it begins rubbing carbon

Page 28

PLEX RETAINER

PLEXIGLAS a SCREWS , NYLON WASHERS ,

L Figure 16 Removal of Fluorescent Lamp material off of the potentiometer. This results ina fine carbon dust that causes the noise.

As in your radio, the Poolshark potentiometers can also begin to be noisy with use. The symptom of this noise in Poolshark is that the cue ball will jump (rather than an even movement) when the joystick is moved.

There are two ways to solve the problem of a noisy potentiometer: 1) Replace the joystick or 2) clean the potentiometer. Economically, cleaning is a better way of solving the problem. However, if some clown pours coffee or pop onto the control panel and the liquid seeps into the potentiometer, it is questionable whether cleaning will solve the problem. But it is worth a try. If cleaning the potentiometers doesn’t solve the problem, then change the joystick as shown in Figure 18.

Cleaning the potentiometer is simple. All you will need is a spray can of tuner cleaner. Tuner cleaner is available at most radio and TV supply houses. When you buy a can of tuner cleaner, make sure you buy the little tube that plugs into the spray nozzle.

Clean each of the four joystick potentiometers as follows:

  • Unlock and open coin mechanism door.
  • Plug little spray tube of tuner cleaner into tuner cleaner spray nozzle.
  • Insert the other end of the little spray tube of tuner cleaner up into the potentiometer as shown in Figure 19.
  • Spray the potentiometer once for no longer than it takes to say the word “‘tick."” Clean, don’t drown the potentiometer.
  • Move the joystick lever in a rapid circular motion for about five seconds.
  • Repeat steps 3, 4, and 5 once for the same potentiometer.
  • Repeat steps 3 through 6 for each of the other three potentiometers.
  • Play a game of Poolshark and determine if problem is solved.
Page 29

WHITE/ORANGE BLACK ORANGE/WHITE BLACK

RED — WHITE/YELLOW RED YELLOW/WHITE LEFT START SWITCH RIGHT START SWITCH

Figure 17 Harness Wire Connections on Start Switches

= . Open coin door. . Remove four #2-56 x 1%2-inch pan

. Puil joystick through coin door. . Remove harness wires and resolder

. Reinstall joystick in reverse order. AM LEVERAGE RING

head screws from leverage ring.

wires onto new joystick.

Figure 18 Removal of Joysticks

Page 30

Hh

X ! | He & ‘i ii) | | ) | | ny Nil ee Dill ah | | ii

Page 31

A. POOLSHARK GAME OVERVIEW Electronically, the Poolshark game consists of a power supply, a TV monitor, a game printed circuit board, and two speakers. Electrically, the Poolshark game consists of a control panel, a coin door, anda fluorescent lamp. Figure 20 illustrates the electronic and electrical assemblies in a block diagram form.

The controlling part of the game is the game printed circuit board (PCB). Since the PCB interfaces with all the assemblies, excluding the fluorescent lamp, the following discussion of the operation of the Poolshark game will focus on the PCB.

B. POOLSHARK PCB OPERATION The PCB is the master controller of the Poolshark game. This assembly is a microcomputer designed and programmed to simulate the functions of a pool game. Figure 21 is a block diagram of the PCB.

Page 32

ac. ‘SOURCE FLUORESCENT LAMP:

INTERLOCK ‘SWITCH

PowER ‘SUPPLY

‘CONTROL PANEL

LEFT PLAYER JOYSTICK

TEFT PLAYER. BUSHBUTION

RIGHT PLAYER. JOYSTICK

RIGHT PLAYER TV MONITOR

MONITOR cIRCUITRY HORIZONTAL DEFLECTION

KEYING

VERTICAL DEFLECTION

‘COMPOSITE VIEO

GAME PRINTED cincurT START PUSHBUTTON

Leo

com DOOR

Wo COIN MECHANISMS

SELF-TEST ‘SWITCH ‘BOARD

‘SPEAKERS

Figure 20 Poolshark Game Block Diagram

Page 33

Figure 21 Poolshark PCB Block Diagram Jovsrien

INPUT

ADDRESS. DECODER "ADDRESS:

Z

‘ADDRESS:

DATA

D

‘ADDRESS. ‘ADDRESS. vive ‘ssaucoy SCORE! PLAYFIELO

GENERATOR

syne

ENABLE

‘ADDRESS:

SCRATCH

PAD

MEMORY

‘ADDRESS: GAME BALL GENERATOR eNnasiE SYNC.

‘ADDRESS

sovstick

‘ADDRESS:

"SOUND Tow MONITOR To ‘SPEAKERS

Page 34

sang PEEEDA Lee : a MUTE iiaeanas = Pitae sPRaGaed EEQERaSERaEDS i & ad

Sn,ye SUL bOdTS

Page 35

Table 3 Aid for Locating Discrete Components in Figure 22

COMPONENT COMPONENT

SCHEMATIC POOLSHARK SCHEMATIC POOLSHARK

REFERENCE PCB GRID REFERENCE PCB GRID DESIGNATION LOCATION DESIGNATION LOCATION

cl H2 C49 L/M10. C2 P2/3 C50 K/L10 (on) P4 C4 P4 CRI AZ C5 N4 CR2 A7 C6 N4 CR3 AZ C7 M/N4- CR4 A7 C8 M/N4 CRS H8 (oe) PS CR6 H8 C10 A7 CR7 H8

CR8 H8 ci A7 CRO AQ C12 £9 CR10 AQ C13 E9/10 C14 C910 CR11 AQ C15 co CRI2 F9 C16 co CRI13 Fo C17 ABO CR14, F9 C18 C10 CRI5 FO C19 C10 CRI6 £9 C20 C10 CRI7 D/E10 CR18 D/E10 21 C10 CRI9 F/H8 C22 BiC10 C23 Al0 LM 323 N10 C24 BiC10 Qs F/H10 Ql B7i8 C30 PI Qe A718 C31 Fl Q3 D9 32 AVBI C33 E/F2 R1 A/B1 C34 K/L3 R2 H2 R3 H2 C35 E/F3 R4 A2 C36 Kil4 RS K3 C37 E/F4 R6 P4 C38 A4I5 R7 P4 C39 K/LS R8 P4 C40 E/FS RO P4 C41 K/L6 R10 P4 C42 E/F6 C43 K/L7 Ru Pa C44 E/F7 R12 N4 C45 K/L8 R13 N4 C46 E/F8 R14 N4 C47 KILO R15 N4 C48 E/F9 R16 N4

Page 36

Table 3 (continued) Aid for Locating Discrete Components in Figure 22

COMPONENT COMPONENT

SCHEMATIC POOLSHARK SCHEMATIC POOLSHARK

REFERENCE PCB GRID REFERENCE PCB GRID DESIGNATION LOCATION DESIGNATION LOCATION

R17 N4 R61 E9 R18 cas R62 £9 R19 PS R63 D9 R20 H6 Rod Ag R65 Ag R21 H6 R66 Ad R22 H6 R67 Ag R23 H6 R68 Ag R24 H6 R69 Ag R25 Ho R70 Ag R26 H6 R27 He R71 Ag R28 A6 R72 AQ R29 A6 R73 D910 R30 A6 R74 c9/10 R75 c9/10 R31 A6 R76 c10 R32 A6 R77 c10 R33 Ab R78 c10 R34 A6 R79 B10 R35 A6 R80 K9/10 R36 AZ R37 A7 R81 K9/10 R38 AZ R82 K10 R39 A7 R83 K10 R40 AZ R84 K10 R85 K10 Rat a7 R86 K10 beg AB R87 K10 bed A8 R88 H10 Rag AB R89 H10 RAS AB R90 H10 R46 AB R47 AB R91 H10 R48 AB R92 H10 a AB R93 Lio R50 P9 R94 L10 R95 yK10 sa ro R96 J/K10 R52 LM9 R97 P10 R53 VK9 R98 M2 Roa F9 R99 F/HB ee Fo R100 E9/10 R56 F9 isd &9 $1 H7 san &9 52 AGI R59 £9 33 H8 R60 F9

Yt H2

Page 37

Poolshark PCB Overview (see Figure 22) For easy reference, the PCB is divided into 130 sections. These sections are identified by letters A through P (skipping letters G, |, and O because they may be easily confused with numbers 6, 1, and 0 respectively) for the short side of the PCB. The long side of the PCB is identified by numbers 1 through 10. The letters and numbers create a grid and all ICs are located on the PCB along the grid lines. For example, identify the IC at location E3. This IC is located on the PCB schematic diagram, Figure 23 (sheet 1, top lefthand corner) as IC £3.

Discrete components (resistors, capacitors, diodes, transistors, etc.) are not identified on the PCB schematic diagrams. Therefore, Table 3 is provided as an aid to be used with Figure 22 to locate discretes on the PCB.

Note that in location M/N/P 10 there is an LM232 regulator (located in large black heat sink) and a 40. 10-watt power resistor. These components produce a good deal of heat during normal operation. The temperature is not extreme, but touching sensitive skin will produce an OUCH!

Another item we would like to bring to your attention is power distribution. Note that on top of the PCB, most of the wide traces are DC ground. On the back of the board the wide trace (along the long end of the board) is +5 VDC.

C. POOLSHARK PCB POWER (see Figure 23, Sheet 1 of 4)

The PCB receives its power from the power supply in two forms: approximately 8 volts full-waverectified DC and 25 volts AC. The 8 VDC is regulated by an LM323 to a stable +5 VDC. The 5 VDC is then distributed throughout the board to power all circuits, excluding the audio output IC. The audio output IC (TDA 1004 in location B10) receives its power through full-wave rectifier CR17 + CR18 and filter C25.

The +5 VDC regulated voltage is also fed through 1kQ. resistors RI, R4, R18, R19, R36, and R65. This voltage is a pull-up voltage labeled P on the schematics. A pull-up voltage is used in output circuitry that is too heavily loaded to get to the high logic state by itself. D. POOLSHARK MICROCOMPUTER (see Figure 23, Sheet 3 of 4) The microcomputer consists of the microprocess or program memory, and scratch pad memory. The microprocessing unit or MPU (location M/N/P 3) is the controller of the microcomputer. From the MPU, a sixteen-bit address bus addresses program memory, scratch pad memory. An eight-bit bidirectional data bus serves as a path for transferring data to the MPU from program memory, from the switch circuits, and to and from scratch pad memory.

The address lines (BAO through BA14) are buffered to eliminate signal loading. The lowernumbered lines (BAO through BA8) address the program memory ROMs (K1 and L1 or Al, B1, C1, D1, E1, Fi, H1 and J1). Scratch-pad memory RAMs (N1 and P1) are also addressed by these same eight address bits.

The higher-numbered address bits (BA10 through BA13) address the address decoder. The address decoder’s outputs enable the section of program memory or the scratch-pad memories—as commanded by address bits BA10, BA11, BA12 and BA14. The LEGIT signal from the MPU and address bits BA13 and BA14 enable the address decoder.

The LEGIT signal from the MPU is derived from phase 2 (02) and VMA. Phase 1 and phase 2 (as illustrated in Figure 24) are constant signals, derived from CLOCK. The VMA signal is an output of the MPU and only exists when the MPU expects a data transfer. Therefore, when the MPU wants a data transfer, it sets up the address lines and sends out a VMA signal; then, when phase 2 goes high, the address decoder is enabled by LEGIT. The output of the address decoder enables the appropriate memory and the transfer is made.

The outputs of the address decoder also enable the score/playfield RAMs, the sound circuits, the object and match RAMs, the START LEDs, and the D-A Latch.

E. MICROCOMPUTER INTERFACE The Poolshark game's microcomputer interfaces with the following circuits: motion circuit, switch distribution circuit, score/playfield circuit, sound circuits, lamp circuits, and joystick circuits.

Motion Circuit (see Figure 23, sheets 1 and 2) During the vertical blanking period, the microcomputer directly accesses the vertical and horizon-

Page 38

tal position RAMs (C7, D7, E7, F7). Data (BDO through BD7) is written into the position RAMs at address locations BAO through BA3 (signals PA1 through PA4 = PSA1 through PSA4 = BAO through BA3). This is the only period during which the microcomputer has access to the motion circuit.

During the horizontal blanking period, the vertical position of each scan line is determined by full adders (£6, F6). When the vertical position (VP4 through VP8) of an object is equal to the vertical sync count, the output of full adder Fé becomes all high logic. This results in alow read/write line of the object RAMs (C5, D5, £5, F5) and match RAM (B5). The data written into the RAMs is the object code data (PAT through PA4) for each horizontal position address location (HP1 through HP8).

In review, the microcomputer instructs the motion circuitry where the objects are to be displayed during vertical blanking. During horizontal blanking, the stored object horizontal location information is accessed and the object code is written into the object and match RAMs before the next horizontal scan line. This defines where that object is to appear on this scan line.

Now remember, horizontal position data was written into the object RAMs and match RAM during the horizontal blanking period, before the scan line began. During horizontal scan time, the object and match RAMs are addressed by horizontal sync 2H through 256H. When the horizontal sync count reaches an address location where match data was stored, a MATCH pulse appears at the output of the match RAM (B5). The pulse is clocked through flipflop A5 and latches an object code (OBJ1 through OBJ4) at the output of flip-flop Bo. The MATCH pulse is fed back to the read/write line of the match RAM to clear the current MATCH pulse.

Ball ROM J5 (sheet 2 of Figure 23) is enabled for balls zero (the cue ball) bhrough ball seven, and ROM H5 for ball eight through ball fifteen. Object code bits OBJ1 through OB)3 are address inputs A6, A7, and A& of the ball ROMs. The vertical data code (VD1 through VD4) comes from full adder E6 (sheet 1 of Figure 23). The full adder outputs a vertical data code from zero to fifteen that instructs the ball ROMs which of the sixteen ball picture lines is being scanned. This code is address inputs A2 through A5 of the ball ROM.

The feast signi ddress bits of the ball ROMs are horizontal data bits HD3 and HD4. These along with HD1 and HD2 are generated by counter J3 at async rate of 1H and initiated by the MATCH pulse. The counter counts up to sixteen and inhibits itself by the terminal count signal OBJ DISP. Horizontal data bits HD1 and HD2 are gated into the PE input of shift register K4 (pin 9). The gating of these two bits shifts the ball ROM data out of the register once for every four counts of 1H. Since horizontal data code HD3 and HD4 changes every four counts of 1H, the results is a ball picture that is sixteen bits wide.

If the ball object code is 0000, the cue ball is displayed. In this situation an additional circuit is utilized. This circuit is that relating to flop-flop B3 (located above the ball ROMs on sheet 2). A cue ball object code produces a high Q BALL output at AND gate C3 for each high OBJ BALLS bit that is shifted out of register K4. This produces a white cue ball video when OB) BALL signal is gated with the Q BALL signal at the video summer (sheet 1). Balls one through fifteen are scanned in black video.

Switch Distribution Circuit (see Figure 23, sheet 3 and 4) During the attract and ready-to-play modes, the microcomputer enables the switch distribution circuit with a SWITCHES (J7, pin 1) signal and addresses (BAO and BA1) the circuit for a resulting DIST 1, 2, or 3 signal. Then the microcomputer looks for a returning SW1, 2, 7, or B signal. If the logic is high, the switch is open, if low, the switch is closed.

During the play mode, the microcomputer enables this circuit to determine the position of the joysticks.

Score/Playfield Circuit (see Figure 23, sheet 2 of 4) During the vertical blanking period, this circuit is addressed (BAO through BA9) by the microcomputer. The address is passed through multiplexers L7, M7, and P7 to the address inputs of RAMs J8, K8, M8, N8, and P8. At this time data (BDO through BD5) for each address location is written into the RAMs.

During scan time, the RAMs are addressed by vertical sync (A5 through A9) and horizontal sync (A9 through A4). When the vertical sync reaches an address location in which data was written, the horizontal data for that scan line is clocked through flip-flops K7 and N7. The horizontal data addresses the score/ playfield ROM. The output of the ROM is multiplexed, one bii aia iime, ihen ciocked througii flipflop D3 at a rate of TH.

Page 39

Sound Circuits (see Figure 23, sheet 4 of 4) There are four sound circuits: scratch, click, score, and bump. All four of these signals are summed at the input of audio amplifier Bi0. The scratch sound is generated by the microcomputer and clocked through flip-flop N9 (output pin 5). Bump is generated by the microcomputer and gated with vertical sync signal 128V.

Score sound begins with SCORE enabling signal that permits counter E8 to count at a rate of 64V. The outputs of E8 are applied to a resistive network that results in the threshold of the timer C9 operating at an analog rate. At the count of sixteen, the terminal count (TC) of counter E8 is gated back to end the 64V count input. Also TC disables timer C9.

Click sound is enabled by CLICK. The sound is derived from sixteen pulses of sync signal 2V. On the sixteenth pulse, counter J9 is inhibited by terminal count (TC).

Lamp Circuits (see Figure 23, Sheet 4 of 4) The START lights are enabled with a START LIGHT signal, then addressed by address bits BA1 and RA? and clocked through flip-flops M9 by address bit BAO.

Note that the schematic illustrates two different types of START lights. Most production models of Poolshark will have the LEDs. However later models may have the incandescent lamps as shown in the dashed box on the schematic.

Joystick Circuits (see Figure 23, Sheet 4 of 4) The voltages from the joysticks’ potentiometers are applied to differential amplifiers J10. The differential outputs of J10 are applied to the positive inputs of comparators H10. The microcomputer then strobes the input of D-A latch B9 with data bits BDO through BD3. The analog output of the D-A latch is applied to the negative input of comparator H10. When the analog conversion of data BDO through BD9 equals the joystick position data, the output of Multiplexer F10 is a low logic signal. This tells the microcomputer where the joystick is, and the microcomputer moves the ball in the appropriate direction.

Page 40

44 PIN EDGE a oe RGN 2) CONNECTOR =n FIOVERS, 41s ies GRD _ 2|s =lOV UNRES = eis HOV UNREG eile

<7 su [oo

TuRT

PLAYER (UPON

PAYER 1 LT/RT

START LED & STAT LEO

NO

DART ZAG.

START Ne]

Woes viDEO GEE SPEAKER SPeaKee SPEAKER GRD SPEALER GRO 25VAC. ZOVAC 2A ZSVAG wey Cr =25v or CRS GRO

love re—

or sa SPEAKERS

Page 41

FLUORESCENT nov [Ren List OUT Sates ——— IR POWER Sea -

UPPLY TR, CHEMATIC. 7 -1e 5797-01 NOVie —_ 4 OUT! | w :

ee ENCLOSURE |

x o

1 0 2% ou Pn eB Me

wl

MONITOR,

le +—ne

Lag xour! cor,

SN SN/8K, te. ____

HARNESS SCHEMATIC

Figure 23 Schematic Diagram (Sheet 1)

Page 42

wit z2m A > hide. AB BROW PTS a g HOLA Teen TES 4H

oft si waa Tapshe ye ye gigrd

PoeSIS24 oe

L_ jaan S sou LB LAN ‘asian

7 —— ff

2sev|RELARErez

ban F iB ql > 2ER8 ASRS. i

psTAN,ae
Psa 3ls |92] ro
eytververan
PSAR20-RISLE x2
o8s4 534ieeckvorzaN
oes Slope es2 vezpat
ra Bion 2+Aa pyAPPsie|ifm
£.+Shas7eav4aS
compEeeaoHpiws}| gunapen; MATER—
Blanc1 ee33VLAN.a
BD31B/772 oep2 weenoe
Kayairs o5°27Mmee
Bo:°Pporz Rie
BosAhaaDtan
2ii} 2tTsfac
cordtri

Hts see Yas nee re 5 bike

ee15..-pam
+HeeSBLARK—!a

Bp? ;

BewePazabe
Bos>.o
804"¢2 Ino
tev+a

3 7S

TPoSIs|rinezi i
“10 ial>Ag
Hoi aefe 1_+2 As
vd2‘ke1olaG

vo3 —*|a “° ge/g—-_ Tee

230s83]t:~ ABLANE—
803Feta 4]toble Teh Tele
3067327Le] le] te—
geeasceoehoehoe,PASaie
eee_=ee 3iesaN

a A

oposoS°saaz
yessvm2+Ba
1310)>Exyadbod
Tal" p71 ogee ves 4?!ile,ettfia“eal 84eas
istheBIEN 1485,2H —S104 pg,Let A
aesvey MP2A£Stig °° zat4pal
iz|A? 9308 Ls4H —S}0B
BD?ne 8 avee HPS~—FiA3a2Tneach+
Bos4Telag24ot2DC“2h
Bb441@H ——4OD S faTA?
3lay 2Ttasia
31‘3 FaBLANK:+tva]

EE

HPSPALef3h93 a]Bas
NOTICE TO ALL PERSONS RECEIVING THIS DRAWINGrie! ks #F32H —4{oa coLOlKe
CONFIDENTIAL: Reproduction torudden wanout thenPe———Laieylhia~°2atas
specific writien permission of Atar. Inc. SunnyvalePahseean —Blo8—
California, This drawing 1s only condilionaly sued. anHPTas790%,Tlicac be
thy noi or cence woe ne suet aero hePB.its528H Yo
rawing or any design ov techmeal amormanon shownTela£4HID.20

thereon. norany fghtforeproduce this drawing" ony Part z2sen —lfons

Inereot except lor manviacute by vendors tata nearLTre

porated and for manufaciure under the corporation's writ. tenlicense no ght o repioduce this drawing is granted oF the subject matier tnereo! unless by written agreement wilh or written permission trom the corporation WRLANK—— Ll?

Page 43

4EDY rene Res Ol ba) 4s Bea

.oeie fig] come vives
CEAfee 2reeBeeZbudcom)
OR BALLSBisa} weeu pi] vices anePp

SOM Thee? LO (baw V BLANK BMP Bak gE? =

eve tevbs ————— == te by {6/2} | wt +4 tele}

sec(77,ol

: rod —4--e 1 i a ' ' + tsv Lo-----4-4ahiz} | i feilee t RIOV 33. apa one ls aate ts ple FIs

fro) forSoresMaTcH

ar Maren

Dist?

gas—2faooo
BatBlam, 7 :ae
SwarenesYE 9aet 3aNOTE: SEE TABLE 4 FOR DESCRIPTION

OF SCHEMATIC SIGNALS.

PCB SCHEMATIC

Figure 23 Schematic Diagram (Sheet 2)

Page 44

Tt ues

an

vos

w

SPAY

Page 45

pean BRN]

oboy ares

Te. BARS

NOTE: SEE TABLE 4 FOR

DESCRIPTION OF SCHEMATIC SIGNALS.

PCB SCHEMATIC

Figure 23. Schematic Diagram (Sheet 3) SAME R AL PLAY FIELD

Page 46

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 47

+50

2} —

Ns

aq

aly NB aa|

1 90-e001 |

Ae 29].

T3¢7:

i aa Ea

AS—-4
|ae+3
Wee “a1FRVESTtg

al : a +i

mare”4—— eg

__ tals = — Baro m Sear bs ae. ~O aloe aan 2 SCS — Bale nr a Be Rie

Leer

INTERRUPT REResT

+ 2

aes\2]47

sa 5

2Moygameda
®$322838?

ay .

ose8saxefaeafiz+5
04} 5 — 4Bar — j]Alon }22.— DrLo>4LOK
. 2sBaz —~ “azait pe—aeaNta B52shee CRE BRAS
aaaa —fan032 osDISTSaYA+CiSWS
’1e _p7——4qDa==>INIOD
5Be., Seleee;oFPCB SCHEMATIC
> ag}ae ‘hk oolz~berest
ay & SoftBS10} - =a
octoR=
ia yeaa 8NOTICE TO ALL PERSONS RECEIVING TH'S DRAWING

neilhes receipt nov possessvan thereo! vonforsor wanstess any night in_or livensu te use the subject matier of the

NOTE: SEE TABLE 4 FOR ardenae or tty aap or techmcal norvauon showt DESCRIPTION OF SCHEMATIC ree eee ens ensore of war nce SIGNALS. Hae eee cartoreprodvce toa caning ronan

igure 23 Schematic Diagram (Sheet 4)

Page 48

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 49

SOUND

Taf

els | acd > elit

ae afe fn

euiee —— soun

Rae 34 89, cRi2 BK Ae ke pe 485 5 4 (ioe

cows COUNTER LYTTL 4 + ave

  • ' as | HP cass wd YP ig maqoot ay 04 INIOO) eas B88 ces tem ce Ap e8 ep in 45 |
°64 i100tv
  • tov ! nee +5V $5V +5
sav 2a aKSVgasRaz

He rBK

lLeK8
ie49, cidSa 2/koIesw3
ape4392zn
A+ Pe ig2ereSih F102
°64 wiootL—ffeo" 28swe
PLAYER~ tovBi 9322,
290Bei5

33% wpe

iaUp HiOa

ep Eos

vhostelyfi

$1013 aa 7 rv Bag

zea 33K

+

ER LAME Reo PLAYER +5v

P= OVACweae

33K

YER Lame

  • evae ny

erp —*lp pg epi 4p “AMP /S WITCH sve —Sp 95 ION eee D NOTE: SEE TABLE 4 FOR

— -9i?DESCRIPTION OF SCHEMATIC

D-A LATCH = SIGNALS.

PCB SCHEMATIC

Figure 23 Schematic Diagram (Sheet 5)

Page 50

tb ANdNI DV LNnoO ASI Ano ANSII ASG6 4 A/NO Rev | NS NMOHS > pron NOWIS73S i Yo BOVNOA AO! ASOZ@ [39/A ISSNVULL

Page 51

PCB AOCOLS55-01 DRMER a TOL — R13 BY | ty zy 2,000 4 f |OR aj! Tat @ |I5v tR/B«{ | 25 vac 8 | +] R/eN|2 Cc 4 _§ ane Pa

llo.5 VAC CT RV

| _.| BU

|S 6.3Vv Ir AC ay

ON ‘77 3K/W TP TP INTERLOCK

ON/OFF SWITCH BK/w vce 7 BK WB) |W N POWER SUPPLY SCHEMATIC

Figure 23 Schematic Diagram (Sheet 6)

Page 52

Schematic Signal Table 4 Definitions of Schematic Signal Nomenclature

Signal Description

BA

BUMP SOUND

CLICK

CLICK SOUND

CLOCK

COMP BLANK

D-A LATCH

DISPLAY

DIST

H

H BLANK

HD Address—Address lines AO through A15 generated by the microprocessor.

Buffered Address—Address lines BAO through BA14 generated by the microprocessor and buffered to eliminate signal loading.

Buffered Data—Bi-directional buffered data lines BDO through BD7 to and from the microprocessor.

Bump Not—Enabling signal from address decoder that enables the bump sound when signal is low.

Bump Sound—Sound signal derived from address signal BAO and 128V, enabled by BUMP.

Click Not—Enabling signal from address decoder that enables the click sound when signal is low.

Click Sound—Sound signal derived from 64V and enabled by CLICK or SCORE.

Clock Not—Master crystal-controlled timing signal that operates at a frequency of 11.055 MHz. Raw CLOCK signai is used for generating all SYNC signals. CLOCK is used to derive the timing signals 91 (phase 1), 62 (phase 2), and DBE (data bus enable).

Composite Blanking Not—Combination of vertical and horizontal blanking (V BLANK and H BLANK) signals. Blanking occurs during period when signal is low.

Data—Eight lines of signal information that provides two-way communications between the microprocessor and memory.

Digital to Analog Latch Not—Signal from address decoder K2 that, when low, enables the digital buffered data input to B9 to be converted to an analog output signal.

Display Not—Signal from address decoder K2 that, when low, enables the writing of the playfield and score information from the playfield/score RAMs. When signal is high, data is written into playfield/score RAMs.

Distribution—Signal used for interrogation of all game switches. Signal return is SW data signal.

Horizontal Sync—Horizontal timing signals derived from CLOCK.

Horizontal Blanking—The period of time beginning with the end of a scan line and ending with the beginning of the next scan line.

Horizontal Display—Four signals that are clocked at a rate of 1H and represent the maximum horizontal width of any of the game balls on a horizontal scan line.

Page 53

Schematic Signal

HP

INTERRUPT REQUEST

IRQ RESET

LAMP.

LEGIT

MATCH

OB)

OB} DISP

OB) BALLS

PA

PFD

POSH

POS V

PSA

Q BALL Table 4 Definitions of Schematic Signal Nomenclature

Signal Description

Horizontal Position—Eight information signals for location of all game balls from RAMs C7 and D7 and applied to full adders K5 and LS.

Interrupt Request Not—Signal during V Blank period that commands microprocessor to finish its present routine, then go to a special routine.

Interrupt Request Reset—Low-level enabling signal from address decoder.

Lamp—Signal that lights the start lamps when high.

Legitimate—When high, data is transferred through the data bus (DB).

Match Not—A low signal that is present when vertical sync is equal to vertical position code. MATCH enables the object code to be latched at the input of the ball ROMs.

Object—Output of motion circuit that represents the digital code for the sixteen game balls.

Object Display Not—A low signal that is present when counter J3 has reached the 16th count, which represents the end of the scanning of one game ball on one scan line.

Object Balls Not—Serial data that represents game balls 0 through 15 and is applied to the composite video summing circuit.

Position Address—During vertical blanking, the four signals are microcomputer address bits BAO through BA3. During horizontal blanking, these signals are horizontal sync 16H, 32H, 64H, and 8H. During scan time, these signals are object code bits OBJ1 through OBJ4.

Playfield Display—Address inputs to the playfield/score ROM.

Horizontal Position Not—A low enabling signal from address decoder that enables horizontal position RAMs C7 and D7 to write in horizontal position data. When signal is high, written-in data is read out of RAMs.

Vertical Position Not—Enabling signal from address decoder that enables vertical position RAMs E7 and F7 to write in vertical position data. When signal is high, written-in data is read out of RAMs.

Position Sync/Address—Address signals BAO through BA3 during vertical blanking period and is sync signal 16H, 32H, 64H, and 8H during non-vertical blanking period.

Cue Ball—Signal applied to video summing circuit to produce a white video cue ball.

Page 54

Schematic Signal Table 4 Definitions of Schematic Signal Nomenclature

Signal Description

a RAMS

RW

SCRATCH

SCRATCH SOUND

SCORE

SCORE SOUND

START LIGHT

SW

SWITCHES

v

V BLANK

VD

VP RAMs Not—Low-level enabling signal from the address decoder that enables the scratch pad RAMs.

ROM Not—Low-level enabling signal from the address decoder that enables program memory ROMs as instructed by the microprocessor address code.

Read/Write Not—When high data is read out of a RAM and low when data is written into a RAM.

Scratch Not—Low-level enabling signal from the address decoder that enables the scratch sound.

Scratch Sound—Sound derived from BAO signal and enabled by SCRATCH.

Score Not—Low-level enabling signal from address decoder that enables the score sound.

Score Sound—Short duration sound that rapidly changes from low to high frequency. Enabled by SCORE.

Start Light Enable Not—Low-level enabling signal from address decoder that results in lighting the START LEDs.

Switch—Data signal to the microcomputer that is low when switch is open and high when switch is closed.

Switches Interrogation Enable Not—Enabling signal from the address decoder. Signal is low when game switches are interrogated.

Vertical Sync—Vertical timing signal derived from CLOCK.

Vertical Blanking—Vertical timing signal derived from CLOCK that represents period from end of last horizontal trace to the beginning of the first horizontal trace. V BLANK represents time while horizontal lines are being traced.

Vertical Data—Output of vertical line comparator of the motion circuit that instructs the ball ROMs which line of the ball picture is being scanned.

Vertical Position—Digital code from vertical position RAMs that is compared to vertical sync at inputs to full adders E6 and F6.

Phase—Two timing signals derived from CLOCK that are used as the basic timing signals for the microprocessor.

Page 55
NOTE: TIME BASE OF TRACES IS .02 pSECI/CM.

Figure 24 Oscilloscope Picture of 81, 82, and CLOCK

Page 56

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 57

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 58

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 59

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 60

ATARI INC 1265 BORREGAS AVENUE * SUNNYVALE, CALIFORNIA 94086 * 408/745-2000 * TELEX 35-7488