CATHODE RAY TOMES

Armor Attack

Armor Attack (Cinematronics, 1980) · Manual · 87 pages · 86 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

OPERATION AND MAINTENANCE,

MANUAL

CINEMATRONICS, INC. 1150 BILLY MITCHELL DRIVE EL CAJON, CA 92020

TELEX: CINEMAT 697891

CALL TOLL FREE: 800 854-6577

IN CALIFORNIA CALL: 714-440-2933

SALES: 8-5 (PST) WEEKDAYS

SERVICE: 8-5 (PST) WEEKDAYS

Copyright 1981 All Rights Reserved

Page 3

CINEMATRONICS INC. ARMOR ATTACK

WARNING: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction’s manual, may cause interference to radio communication. As temperarily permitted by regulation it has not been tested for compliance persuant to Subpart J of part 15 of FCC rules, which is designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
Page 4

TABLE OF CONTENTS

Section Title Page

PURPOSE AND LIMITATIONS OF THIS MANUAL .........-.0-0 0c reece eee i WARRANTY — oo... one cette ete e bene te ner b nent e eee t eens fi

CUSTOMER SERVICE PROCEDURES FOR AUTHORIZED DISTRIBUTORS ..... iti

PART ONE Information for Operators

Section Title Page

1 HOW TO PLAY ARMOR ATTACK 1-1

2 RECEIVING AND INSTALLING ARMOR ATTACK ...........052. 002000 2-1

3 GENERAL INFORMATION AND PERIODIC MAINTENANCE .........-.. 3-1

4 OPERATOR’S GUIDE TO TROUBLESHOOTING ..........-- 2.00 eee e eee 4-1

PART TWO

Information for Technicians

Section Title Page

5 5-1

6 6-1

C. Audio Board 6.0... eee cece cece e teen e ene t eee

7 TROUBLESHOOTING ........-. 0.06. c cence cence eee e eee 7-1

8 PARTS LIST 8-1

APPENDIX A

Assembly Drawings, Schematics, Wiring Diagrams.

Page 5

PURPOSE AND LIMITATIONS OF THIS MANUAL

This manual cannot and does not replace technical expertise. Should out of warranty repair be necessary, we suggest the operator protect his/her investment by hiring an experienced, competent technician (preferably with some knowledge of the Vectorbeam tm Monitor). We have seen many examples come into the factory of incompetent repair creating many more problems than originally existed. One common fault is incorrect substitution of parts. Another is damaged foil traces on PC boards. Repairing broken foil is time consuming and therefore costly. This manual has 2 major purposes, and is correspondingly separated into 2 major parts. Part one of the manual contains information operators need to know. It has been written to tell people who have little or no technical knowledge what they should know about this game, without getting technical. Part one contains valuable information about the Armor Attack Game, receiving inspection and installation, an introduction to the major electronic sections of the game, and an operators guide to trouble shooting — finding the source of a problem with a minimum of technical jargon. If you need more assistance than this manual can give call Cinematronics’ Customer Service Department at our toll free number. Part II of this manual is designed to help the qualified technician understand the functions of the various circuits in the game, and quickly troubleshoot any problems. Part II contains Theory of Operation, Trouble shooting Procedures, Schematic and Wiring Diagrams, Layout Drawings, Parts List, and suggested test equipment. If you need further assistance, please call Cinematronics’ Customer Service Department at the toll free number.

Page 6

WARRANTY

Cinematronics, Inc. warrants the goods to be free from defects in material and workmanship under normal use and service for a period of ninety (90) days from the date of shipment from factory. Cinematronics makes no representation or warranties concerning the goods whether express or implied by operation of law or otherwise, including those of merchantability or fitness for any particular purpose, or with respect of patent infringement, except as may be specifically made herein. Cinematronics limits its warranty obligations herein to the repair or replacement of such parts which have been returned to Cinematronics’ plant at purchaser’s expense and which examination shall disclose to Cinematronics’ satisfaction to have been so defective and to the shipment of such repaired or replacement parts to the purchaser F.O.B. the shipping point.

This warranty does not apply to any Cinematronics product which has been altered or repaired by unauthorized personnel or service facilities or any products which have had the unit serial number altered or removed.

Upon acceptance of the goods, the purchaser agrees to assume all liability for damages and/or bodily injury by the purchaser or any other person and to hold Cinematronics, Inc. harmless from liability or claims arising from the use of the goods by any person. Purchaser further agrees to indemnify Cinematronics, Inc. from any liability, claim, cause of action or litigation resulting from the use or misuse of the goods by any person.

Parts returned for warranty service must be packaged so that no damage is incurred during the shipment. Full documentation and instructions must accompany returned parts. Parts must be shipped prepaid to:

Cinematronics, Inc. 1150 Billy Mitchell Drive El Cajon, CA 92020

Page 7

CUSTOMER SERVICE PROCEDURES

FOR AUTHORIZED CINEMATRONICS’ DISTRIBUTORS

It is the desire of Cinematronics, Inc. to provide efficient and courteous service should the need arise. We have a fully staffed Customer Service Department and encourage you to call our toll free number: 800-854-6577,78, for technical assistance between the hours of 8:00 A.M. and 5:00 P.M., California time, Monday through Friday.

In order to provide the very best service possible, the following procedures for ordering or returning parts must be followed:

  • All equipment ordered from Customer Service, whether in or out of Warranty, must be placed with a Distributor’s purchase order, either by mail or verbally by telephone.
  • Advance replacement items may be obtained only during the term of the Warranty and when such items are available, using the same procedure as when ordering parts. When ordering a PCB. please include with your order the game serial number and the number of the PCB you wish replaced.
  • Allitems received as advance replacements will, after a period of thirty (30) days, become the property of the Distributor, with applicable charges applied in the event Customer Service has not received the defective item against which the advance replacement was made.
  • The Distributor must call this facility for an RMA number prior to returning any item. Please be prepared to provide us with the game serial number and the PCB number when requesting an RMA.
  • Inall situations covered above, and in all other situations, the Warranty offered by Cinematronics, Inc. is applicable and should be fully understood.
  • Parts returned for service must be packaged so that no damage is incurred during the shipment. Cartons without a prominently displayed RMA number will not be accepted. Full documentation including game serial number. PCB number and reason for return must accompany parts. Ship prepaid to:

Cinematronics, Inc. Customer Service Department 1150 Billy Mitchell Drive El Cajon, CA 92020

800-854-6577 714-440-2933

iii

Page 8

PART ONE

Information for Operators

Page 9

SECTION 1

HOW TO PLAY ARMOR ATTACK

INTRODUCTION

Armor Attack is a one or two player Battle- Action game, with features geared for maximum player appeal: unsurpassed realism (functional tank treads, turret recoil, burning debris, ‘War Zone’’ audio) and progressive levels of difficulty. The game adjusts itself to the skill of player, e.g., if you’re skilled, it plays harder.

GAME PLAY

The play field is a top view of a city with road and building areas defined. Players (jeeps) and enemy (tanks) can only manuver on the roads, however the enemy chopper can go over buildings and roads. Whenever the player shoots and hits the side of the building the missile explodes. The shots are only valid over road areas. Debris left by tanks is not self-destructive and can be driven around.

The object of Armor Attack is to accumulate the maximum number of points possible. This is done by shooting tanks and/or choppers. (Shooting other player in a two player game does not count.) The player must also avoid being shot by either the tank or chopper. If the player shoots a chopper, the bonus level is incremented by 10 points. When the fifth chopper is destroyed an extra jeep is awarded (Bonus Level +10, +20, +30, +40, extra jeep). The players turn is over when he gets shot by the tank or the chopper. In a two player game, the round is not over until both players are shot. The number of rounds per game is set by the operator. Points are awarded as follows:

  • SHOOTING TANKS 20 Points is scored for hitting the body of the tank (first hit) 30 Points is scored for hitting the turrets (second hit) The Bonus Level is also awarded for hitting the turrets (the Bonus Level of 0- 40 is determined by the number of choppers destroyed.)
  • SHOOTING CHOPPERS 100 Points is scored for shooting a chopper. The Bonus Level is also incremented.

MODES OF PLAY

There are two modes of play in Armor Attack 1) The one player mode; and 2) The two player mode One player mode is selected by inserting coin or coins and depressing the one player start button. The player (jeep) will appear in the center of the screen and flash until one of the player control buttons (left, right, forward and fire) is depressed. The player then uses the left, right and forward buttons to manuver the jeep around the screen. If a player runs into a wall he will merely stop or slow down but no damage will occur. When a player is pointed at a target, pressing the fire button will launch a missile. A maximum of 2 missiles is allowed for a player at any given time. The player can be destroyed three ways;

  • If a player is shot by a tank
  • Ifa player is shot by a chopper
  • If a player is run over by a tank The number of times a player can be destroyed is determined by the number of jeeps per game selected on the 7-position option switch on the logic board. If a player shoots a tank once, there is a time limit to shoot the turret. If the player does not shoot the turret, it will explode automatically and no points will be awarded.

TWO PLAYER MODE

The two player mode is selected by inserting coins and depressing the two player start. Both players jeeps will flash (to draw attention to them) until a player control button is pressed. Start buttons will have no effect during the play of the game. The players cannot shoot each other. The rest of the play is the same as a one player game except for the following exception: If one player is destroyed, the next round will not begin until both have been destroyed.

Good Shooting

Page 10

SECTION 2

RECEIVING AND INSTALLATING ARMOR ATTACK

RECEIVING INSPECTION Your game was shipped in ready-to-play condition. However, after removal of the shipping carton, a brief visual examination is suggested.

Naturally, you’l] want to make note of any physical damage to the game cabinet and its external components for freight claim purposes. Considering the quality of the shipping carton, any damage to the exterior would indicate possible interior damage as well.

The interior of the game should also undergo a brief examination for: loose mounting hardware (check to be sure that the major components are still securely mounted); disconnected or loose wires, cables or harnesses; electronic devices loose in their sockets; etc.

At this time the game serial number should be logged. Please remember that the game serial number will be required if you need service from your distributor.

ELECTRICAL REQUIREMENTS

Unless specified otherwise, your game was shipped to operate at 115 VAC, 50/60 Hz. Two other voltage settings are possible. The power supply chassis has a table which shows the voltage options and fusing requirements.

A good earth ground is essential for the proper operation of this game or for that matter any electronic device. Problems with instability and erratic operation of computertype devices can usually be traced to an

2-1 ineffective ground system. Therefore, plug the game into a properly wired 3 prong outlet. If a 3 prong to 2 prong AC adaptor must be used, an alternate method of grounding the third prong must be used.

INITIAL ADJUSTMENTS

NOTE

When the game is connected to AC power, one of the game sounds may be heard. This is normal.

The audio level (volume) can be easily adjusted and THIS IS ACHIEVED BY ROTA- TION OF THE VOLUME POT LOCATED ON THE COIN DOOR. The audio level should compete with other machines ‘‘on the floor’’ to maximize play time.

Display brightness is another easy adjustment. The monitor assembly has several adjustments, but the brightness control is the only one which does not require a “‘screwdriver’’ for rotation. Keep the brightness at the correct level for appeal.

OPERATOR OPTIONS

The option switches allow you to select how many ships per game, how many coins per credit, and a test pattern for the Vectorbeam monitor. The option switch is located on the logic or game board. It is not necessary to remove the board from the cabinet to set the options. In fact, the option switch and audio control can be reached easily through the coin door opening. Table 2-1 will assist you with your selections:

Page 11

TEST PATTERN

coer

ARMOR ATTACK OPTION SWITCHES LOCATED ON LOGIC BOARD AT POSITION E-2

JEEPS PER GAME

SEE TABLE ONE

CREDITS PER GAME

SEE TABLE TWO SOUND IN .ON: SOUND ATTRACT MODE’ OFF:NO SOUND NOT USED

DIAGNOSTIC — ON: NORMAL PLAY OFF: TEST

LUU

TABLE ONE TABLE TWO

JEEPS CREDITS SWITCH | SWITCH] " beg SWITCH| SWITCH |” per 1 2 GAME 3 4 COIN

2-2

Page 12

SECTION 3

GENERAL INFORMATION AND PERIODIC MAINTENANCE

Your Cinematronics game is designed much the same as conventional video games. The major exception is the use of an alternate means of visual display the patented Vectorbeam tm* monitoring system. However, the game is built of the same basic building blocks as any other video game.

The Power Supply provides all the

necessary voltages for the CPU board, audio

board, Vectorbeam monitor, and flourescent light. As you look in the back of the cabinet, it is located on the lower left side of the cabinet. The power supply has two circuit breakers, and a 3 ampere sloblo fuse. If one circuit breaker trips, the other breaker will soon follow. Always unplug the game before replacing the fuse or resetting the circuit breakers. If you need to replace the fuse use only a3 amp. slo-blo fuse. The power supply also has a line voltage select switch that must be set to match the voltage in your area. There is also an adjustment for the +5 volt section. DO NOT ADJUST unless you use a volt meter and follow the procedure in Section 6. If needed, this power supply is directly interchangeable with the power supplies used in previous Cinematronics games.

The Central Processing Unit (CPU) is the ““‘brain’” of the game. As you look in the back of the cabinet it is the large PC (printed circuit) board on the right side. It ‘‘senses’’ when a coin is dropped in the coin slot, operates the coin meter, and gives credit. It then ‘‘reads”’ what is happening at the operator controls, interprets and computes to make the game play according to what buttons the player pushes. It tells the Vectorbeam monitor what to draw on the screen, and it tells the audio board when to make the appropriate sound effect. The CPU has a red LED (light-emitting diode), near the Molex power plug. This LED

3-1 normally flashes once when power is turned on, then stays off. More on this in Section 6.

The Audio Board generates all the sound effects for the game and powers the loudspeaker. As you look in the back of the cabinet, it is the smaller PC board on the right side, just below the CPU.

The Vectorbeam tm" Monitor is the picture tube and associated ‘‘Monitor Board’. It draws pictures on the picture tube screen according to the instructions it receives from the CPU. If it does not receive correct data from the CPU, it will pop the circuit breakers. The only operator adjustment here is the brightness control (See Display P.C.B. Connectors and Adjustments, pg. A13. For test purposes (e.g. to check the CPU), the Armor Attack monitor can be replaced by any previous Cinematronics monitor, except Sundance.

The Vectorbeam tm* Monitor is a completely different system from the standard raster-type monitor. Two advantages to this monitor are:

  • circuitry is simplified, and
  • ability to draw fine detail in the picture far surpasses conventional monitors, adding interest to the game. If your monitor should need repair in the future, the technician should be familiar with the Vectorbeam monitor, because it is so different from the conventional raster system.

Interconnecting Cables are of 2 types: The Main Wiring Harness, and the Ribbon Connectors.

The Main Wiring Harness carries power from the power supply to the CPU, audio board, and monitor. It connects to each unit

Page 13

through the Molex plugs. The Molex plugs are built so they can only plug in the right way. NEVER CONNECT OR DISCONNECT THE MOLEX POWER PLUGS UNLESS THE GAME IS UNPLUGGED.

The Ribbon Connectors carry data to and from the CPU. Since they can plug in two different ways, care should be taken to plug them in correctly. For the CPU, the ribbons are plugged in correctly if the ribbon is naturally directed away from the board (See Universal Bench Test Configuration, pg. 7-3). The ribbon at the monitor should also be directed away from the board. (See Universal Bench Test Configuration, pg. 7-3). The audio board is different: the ribbon should go up across the audio board. (See Universal Bench Test Configuration, pg. 7-3).

3-2 PERIODIC MAINTENANCE

The only Periodic Maintenance required is an occasional cleaning. The very high voltage used on the picture tube attracts dust that gradually degrades picture quality. To clean: unplug game and let sit for at least 5 minutes to let voltages ‘‘bleed-off.’’

The monitor is mounted in the cabinet. on brackets. Remove the top bolt from each bracket and gently lower the monitor. Now you can clean the face of the picture tube, and the plexiglass cover. A mild solution of dish detergent will clean the plexiglass without harming the color decal. Care should be taken to not rub the decal, as it may be brittle with age.

Page 14

SECTION 4

OPERATOR’S GUIDE TO TROUBLESHOOTING

or How do I Figure out Which Board to Send Out for Repair?

O.K. - this is where we get technical on you

  • but don’t panic! We’ll keep this as simple as possible so you can figure out which board to send out for repair. For some of the steps in this section you will need a simple VOM, and know how to use it.

Here are two important procedures we will refer back to in this section:

Checking the LED :

Whenever there is a problem with the game, a good place to check first is the LED (light-emitting diode) on the CPU board near the Molex power plug. This LED indicates whether most of the CPU circuit is working. When everything works right, here’s what happens: Power to the game is turned on, the LED flashes on, then stays off. If the LED is flickering or on continuously, there is a problem with the CPU or the +5 volt supply. Check +5 volts on the logic board (follow procedures in this section). If the +5 is O.K., have CPU repaired.

4-1 Checking the +5 Volt Supply:

To check the +5 volts, you need a voltmeter. Turn power on in the game. Notice on the upper corner of the logic board nearest you is a little pin marked gnd. This is a great place to put the negative probe of the voltmeter. Near this pin in position T13 (see CPU layout, pg. A-8) is a 20 pin IC marked 74LS377. Ignore the other numbers on this chip. We can measure the +5 volt supply at pin 20. Pin 20 is the bottom pin on the far side of the chip. Put your positive probe there, without touching any other pins, and you should get a reading. Anything between +4.8 volts and +5.1 volts is 0.k., otherwise, adjust the voltage.

The adjustment is located on the power supply, and it is the only screwdriver adjustment on the power supply. Adjust slowly WHILE READING THE VOLTAGE. Too much voltage will destroy IC’s fast. If voltage cannot be adjusted into the correct range (+4.8- + 5.1 volts), repair power supply.

Page 15

The following is a guide compiled from experience. It cannot be right 100% of the time:

SYMPTOM WHAT TO DO

Circuit breakers trip 1. Unplug game. Unplug Molex power plug from monitor and reset breakers. Turn POWER ON. If breakers trip: POWER OFF, see 2. If breakers don’t trip: Coin-up game and “play” it. Are all sound effects normal? Yes - repair monitor. No - Problem is probably in CPU or power supply. Check LED on CPU. Check +5 volts on CPU (see procedure) If +5 volts is good, repair CPU.

  • Unplug Molex power connector from audio board, reset breakers and turn POWER ON. If breakers trip: Problem is in coin meter circuit or call factory for help. If breakers don’t trip: Repair audio board. POWER OFF, reconnect molex plug to monitor. Turn power on to see if there is a good picture. If the picture is bad, problem is probably in the monitor. If breakers trip: Check LED and +5 volt supply. If LED and +5 voltsis O.K., problem is probably in monitor.

4-2

Page 16

PART TWO

Information for Technicians

Page 17

SECTION 5

VECTOR THEORY

In order to understand the basic concept behind a vector generated display, it is

important to have a basic knowledge of vector theory.

In the vector display system, there are no horizontal and vertical lines (no sweep) or sync. A line generated using a vector system is shown in Figure 5-1.

A line is drawn by programming a beginning and ending point of the line to be drawn, and forcing the cathode beam to travel between these two points, illuminating the entire path on the screen of the CRT. The angle of the line, the position of the line, and the length of the line are determined simultaneously, and simply, by selecting the proper voltage levels for the beginning and ending points of the line.

This is accomplished by the two twelve-bit codes (words) applied to the DAC-80s on the display board. The DAC-80 will produce a

5-1 different voltage level at its output for each possible combination of input bits (of which there are 4096 possibilities for a 12 bit word.)

It is also important to remember the function of the LF 13331 analog switch and its output RC network. Because we are dealing with reactive components in C101 and C201 on the display board the charging voltages found are non-linear by nature. (See figure 5-2).

Therefore, when a line appears on the CRT, it is actually only part of the entire path taken between the beginning and ending points of the vector (C-D). The section of A-B is chosen as the most linear portion of the charge curve, and is illuminated.

Sections C-A and B-D are blanked at the cathode and section A-B illuminated by controlling IC7 (7406) on the display board. These calculations are all performed on the CPU logic board.

Page 18

Li tT tT SSSR ae fT ett TTA [fondradng voteage poake | | || | TA FT TT TY

Figure 5-2. Non-linear Charging Voltages

When a line appears on the CRT, it is actually only part (section A-B), of the entire path taken between the beginning and ending points of the vector (section C-D). Section A-B is chosen as the most linear portion of the charge curve, and illuminated.

5-2

Page 19

SECTION 6

THEORY OF OPERATION

GENERAL DESCRIPTION

This section describes the principles of operation of the major circuit functions of the Cinematronics Video Game. The system’s general functional description is followed by detailed circuit schematics which are included as Appendix A. The schematics used in this manual are similar in nature to those used by most industrial electronic firms.

A. MONITOR The Vectorbeam tm* Monitor is unlike the conventional TV monitor in that it displays vectors (lines) generated from X-Y coordinates received from the logic board. The horizontal points are X (width) and the vertical points are Y (height). The X and Y logic signals originate from the logic board.

The Vectorbeam tm” Monitor circuitry is so different from a raster scan monitor, it is useless to try to troubleshoot it using raster T.V. theory. The Vectorbeam tm* Monitor has no horizontal oscillator, no vertical oscillator, no AFC, no sync circuits, and no video amplifiers. How, then, does it work? The Vectorbeam tm* Monitor can be divided into 4 main sections: voltage regulators; deflection circuits; video high voltage module; and brightness circuit (cathode drive).

There are three voltage regulators on the monitor board: +15v, -15v, +5v. Note that these are IC’s, not transistors. The plus and minus 15 volt regulators supply both DAC-80’s, the LF13331 analog switch, and the TLO81 op amps. The +5 volt regulator supplies both DAC-80’s and the 7406 (IC7). It takes little time and is well worthwhile to check all 3 regulator outputs every time the monitor is serviced. Drawing a line requires two separate steps.

STEP 1. Digital information, in the form of a 12 bit word is applied to the input (pins 1 thru

  • of the DAC-80. Pin 1 receives the most significant bit, and pin 12 the least significant. The DAC-80 converts the digital word into an analog voltage which is outputted on pin 15. This voltage can swing between +5 volts, depending on the input word. The output of pin 15 then goes through acurrent limiting resistor R130 to the inputs of the analog switch IC1. (Pin 18 of the DAC-80 is an input for feedback). Now the CPU sends out an Initial Position pulse, closing the appropriate ‘‘switch’’ (actually a J-FET), to let the analog voltage out pin 10. C101 charges up immediately, and the analog voltage is amplified by IC 102 and the transistorized section Q101 thru Q111, causing the yoke to deflect the cathode beam to where we want the line to begin - the Initial Position.

STEP 2. Another 12 bit word is fed into the DAC-80. This word determines where the end of the line we are drawing will be. The DAC-80 again converts the digital word into an analog voltage that goes out pin 15 and into the analog switch IC1. Now the CPU sends out a Line Drawing pulse, closing the appropriate “‘switch’’ to let the analog voltage out pin 15 of ICl. The combination of R103, R102, and C101 has a time constant that determines how quickly C101 can charge (or discharge) to the new analog voltage on pin 15 of IC]. By adjusting R102, we change the amount of time it takes for C101 to arrive at the new analog voltage on pin 15 of ICl. Thus R102 determines the line length in the vertical (Y) direction. If the second (Line Drawing) analog voltage (IC1 pin 15) is greater than the first (Initial Position), the line will be drawn downward. If the second voltage is smaller, the line will be drawn upward.

Page 20

In the horizontal channel, if the second analog voltage is greater than the first, the line will be drawn to the left.

Op-amp [C102 serves a dual purpose: It acts as a buffer between the deflection amplifiers and the analog switch, as well as an “edge gain”’ amplifier.

At the output of IC102, there is a resistor diode network consisting of R105 to R110, and D101 to D104, This resistor diode network is used to compensate for the non-linear characteristics of the CRT near the edges of the screen. If this circuit were not used, any object displayed on the screen would increase in size as it moved closer to the edges of the screen. Potentionmeter R109 adjusts the height of the pictures.

From the wiper of R109, the signal proceedes to Q101, which is the first stage of deflection amplification. Q101 to Q111 form a typical modern direct-coupled power amplifier with differential pair input and full complementary output. The differential pair consists of Q101 and Q103. The base of Q103 is tied to the amplifier output through the yoke and R117, forming a negative feedback loop. Q101 and Qi03 (differential pair) compare input signal and amplifier output, and correct for any differences caused by amplifier distortion and the reactance of the yoke. Q102 is the constant current source for the differential pair (Q101, Q103). Bias for Q102 must be kept steady so Q102 collector current is constant. D105, D106 and R113 accomplish biasing. Note D105, D106 are in parallel with the base emitter junction of Q102 and R113. The voltage across Q102 B-E junction plus voltage across R113 will equal total voltage across D105, D106, and the two forward biased diodes determine this voltage at 1,2 volts. Since the voltage across the B-E junction of Q102 is 0.6 volts, that leaves 0.6 volts across R113. The voltage across R113 is held constant, so the current through it is constant (I=E+R) at 3 ma. Thus Q102 collector current is held constant near 3 ma.

The output of the differential pair (Q101, Q103) is fed into the base of Q104. Q104 isa class A amplifier whose output feeds Q208 and Q209.

6-2 Q105 is another constant current source. D109, D110, D111 determine the bias current in Q108, Q109, Q110, Q111.

So the deflection signal has traveled to the base of Q108 and Q109, the driver transistors. If the signal happens to swing positive Q108 will turn on, turning on Q110 which drives current thru the yoke and deflects the electron beam down. If the signal swings negative, Q108 and Q110 turn off, Q109 and Qill turn on, and the beam deflects upward.

If the signal amplitude is excessive Q110 or Q111 (also known as the output transistors) will conduct heavily. The excessive current will cause voltage to develop across R120 or R121, and Q106 or Q107 will turn on. When this happens, the signal is removed from the base of Q108, Q109. Q108 and Q110 or Q109 and Q111 are turned off by this action and are protected from burning up. So Q106 and Q107 are protection transistors, and during normal operation they are inactive.

Note that Q108, Q110 contro! deflection in the lower half of the CRT screen, while Q109, Ql11 take care of the top half. In the horizontal (X) channel Q208, Q210 control the left half; Q209, Q211 control the right.

Because the amplifier is a direct coupled loop, it defies ordinary signal tracing as a means of troubleshooting. If the signal is wrong anywhere in the amplifier, it will be wrong throughout.

R122, R123, and C102 form a RC network, which compensates for any counter EMF that may develop by the expanding and collapsing of the deflection coil’s electromagnetic field.

The video high voltage module operates off the +25v supply and generates three different voltages for three circuits. It generates 16KV for the CRT ultor voltage. It generates +400vdc for the CRT focus voltage. And it generates +90 volts for blanking the cathode. The +90v is well filtered and fed into the brightness circuit on one end of R111.

Page 21

The brightness circuit controls the amount of current going from the CRT cathode to the phosphor screen. It does this by varying the voltage on the CRT cathode. It also incorporates protection circuitry to protect the phosphors from burns. The main components in the brightness circuit are IC7, Q1, Q2, Q3, Q6, Q7, Q8, and R111, the brightness control. There are only two levels of brightness used in this system, which I will refer to as Normal and HI. The brightness information comes from the 74LS32 in position J2 on the logic board, through the ribbon connector, and into IC7. Normal intensity data enters IC7-1, and HI intensity data enters IC7-3.

Normal intensity data then goes out IC7-2 and turns QI on-off. Ql acts as an on-off switch connecting and disconnecting R7 to ground (thru Q2). Thus, when Q1 turns on, the CRT cathode voltage is lowered (assuming R111 is at a normal setting) and the beam is turned on. When Q]1 turns off, CRT cathode voltage returns to +90 volts, and the beam is cut - off (no brightness on screen).

Hi intensity data goes out IC7-4 and turns Q3 on-off. Q3 collector is connected to R8 (10K) in parallel with R9 (2.2K), R10 (5.6K). When Q3 turns on there is a lower resistance path between CRT cathode and ground than there was when QI turned on. Thus CRT cathode voltage drops to a lower voltage, and more current flows to the phosphor screen, creating a higher brightness.

Note that when either Q1 or Q3 conducts, the only path to ground is through Q2. If Q2 is off, the CRT cathode voltage cannot change, and no picture can appear. This means Q2 is a master ON-OFF switch for the cathode beam, and is the means through which our protection circuits can turn the beam OFF.

The first protection circuit consists simply of an unfiltered full-wave rectified +25 volts from the power supply. This voltage is slightly filtered by C10 and fed through R6 to Q2, turning it on. When the game is unplugged, the +25 unfiltered dies immediately and the beam is cut off, preventing a bright spot on the screen.

6-3 The second protection circuit consists of Q6, Q7, and two sections of IC7. Part of this circuit turns off the beam if the -25 volts from the power supply is lost (breaker trips, or?). In the absence of -25 volts, IC7-9 goes high (pulled up via R20), and IC7-8 goes low, pulling the base of Q2 to ground and Q2 turns off.

The other part of the circuit protects against having the beam on too long (in case of CPU failure, etc.). The high going pulses coming out of IC7-2,4 that turn on Q1, Q3 also turn on Q6 via R22, R23. Q6 amplifies and inverts these pulses to high-going low. Pulses then go through another inverter, so at IC7-10 they are low going high (active high). The active highs here correspond tothe times when the beam is on, and charge up C24. If the beam is on too long, C24 will charge up enough to turn on Q7, making Q7 collector and Q2 base go low and Q2 turns off. In normal operation C24 can discharge through 1C7-10 when IC7-10 goes low.

Now, a paragraph about Q8. Q8 is the path through which IC7-2,4 receives its operating +5 volts. R19 and C23 form a time delay, so when power is first turned on it takes a while before Q8 turns on and +5 volts gets to IC7-2,4. Thus, all other circuits get a chance to stabilize before the beam is turned on.

R111 is the brightness potentiometer, which adjusts the amplitude of the negative pulses used for Normal and HI brightness.

B. CPU BOARD

The processor hardware can be broken down into five basic functional blocks as shown in Figure 6-1. The arrows indicate the possible data flow directions between the various blocks. The ALU and Control} block are the main components of the processor while the Memory and I/O blocks may be thought of as merely peripherals. Figure 6-2 is a detailed block diagram of the processor. The numbers in each block correspond to the entries in Table 6-1, which lists the IC numbers of the main components of each functional block.

Page 22

CONTROL UNIT

Figure 6-1. CPU Functional Block Diagram

Page 23

The following is a brief description of each block shown in Figure 6-1. The numbers beside each functional block name are the numbers in Figure 6-2 which correspond to a particular function.

RAM (6)

The RAM is implemented with three read/write static memories configured as a 256 x 12 bit block. Data can be transferred to or from this memory via the ALU block. The processor uses this RAM as a scratch pad.

ROM (10)

The ROM is configured as an 16K x 8 bit block of memory. These memory locations contain the program instructions and/or data. It is accessed via the processor control unit.

1/0 19, 17, 18

The I/O block consists of 8 output lines implemented with a bit addressable latch, 24 input lines implemented with data selectors, and two 12 bit registers which are connected to the X Y display deflection circuits via D/A convertors.

Arithmetic Unit 1,2,3,4,5

The arithmetic unit performs all the arithmetic processing for the system. It consists primarily of two 12 bit accumulators, an arithmetic logic unit and various data selectors. The accumulators can function as temporary storage registers for arithmetic functions upon the data in the accumulators. The data selectors are used to select the various sources of data which will be processed.

Control Unit (15,16,14,7,8,9,11,12,13)

The control unit is the heart of the processor. It performs all instruction decoding operations and generates all the necessary control signals which the rest of the hardware requires to function correctly.

The following is a discussion of each block shown in Figure 6-2.

6-5

  • Accumulator Selector

The accumulator selector consists of 3 quad data selectors. They are used to select the output of either the primary or secondary accumulator for processing by various other sections of the systems.

2 & 3 Primary and Secondary Accumulators

The two 12 bit accumulators are implemented with quad bidirectional shift registers. The primary accumulator consists of S4, P4, M4. The secondary accumulator consists of T4, R4, N4. All data manipulation in the processor is accomplished using these two accumulators. All output data flows through these registers.

  • Arithmetic Logic Unit (ALU)

The ALU is used to perform all necessary arithmetic functions within the processor. The ALU is implemented using three 24LS181 (N6M6L6) function generators, three 74LS85 (N9,M9,L9) 4 bit magnitude comparators, and a74S182 (L4) look ahead carry generator. The data which the ALU manipulates can come from four different sources. The first source is the contents of the accumulators via the accumulator selector. The second and third sources are the ROM and RAM data outputs via the ALU data selector (N11, M11, L11) and the fourth source is the external input selector (E4, D4, C4).

  • Data Selector

The data selector is used to read data into the ALU from either the RAM or ROM memory. Note that the ROM data is only 8 bits wide while the RAM data is 12 bits wide.

  • RAM Storage

The system RAM consists of three 9101C high speed static memory chips connected as a 256 x 12 bit block. The block is 12 bits wide in order to allow the contents of an accumulator to be stored. The processor uses the RAM as temporary storage of program variables, data pointers or any other data of a dynamic nature.

Page 24
  • RAM Address Selector/Register

The output of this register is tied directly to the address lines of the RAM. It consists of a multiplexer which routes address data from either the ROM or RAM locations to the RAM address lines. The capability to use RAM data to select RAM addresses is the basis for the indirect addressing mode of the processor.

  • Page Selector

The page selector is used to latch the high order 4 bits of a RAM access instructions.

  • ROM Data Register

The register is used to temporarily hold data from the ROM during an instruction fetch.

  • ROM Memory

The ROM memory consists of the actual memory chips plus a data selector and latch circuit. The latch is used to improve the memory access time during a two byte instruction fetch by allowing one byte of the instruction to be latched while the RAM address lines are decoded for the other byte. The data selector can then be used to rapidly access both bytes of the instruction by switching between the latch and memory outputs.

  • Instruction Register

The instruction register is a latch which holds the current op code as read from ROM. Its output is tied to the instruction decode circuitry which in turn generates the necessary signals to execute the instruction.

  • System Sequencer

The system sequencer is used to decode an instruction op code and to generate the appropriate timed sequence of signals which execute the instruction. The op code is decoded by using it as the address data to a set of decoder ROMS. The outputs of the decoder ROMS are then synchronized with the system clock and used to contro! the various system functional blocks.

  • Line Length Counter

The fine length counter is used during the process of drawing a vector to control the length of a vector, by turning off the beam at a pre-determined time after the vector is intiated. The counter is loaded with a value from a line length ROM and then counts up until it overflows which in turn generates a signal to indicate the vector has been finished.

  • Program Address Selector

This selector is used to provide the address data to the program ROM. It selects either the program address counter output or the accumulator selector output and routes this data to the ROM address lines. The ability to use the accumulator contents as address data allows the program to randomly access data tables stored in the ROM or to compute a branch address after a conditional test.

  • Program Address Counter

This is a 12 bit counter whose output defines the next location in ROM to be accessed. It is normally clocked sequentially to step through a program. However, it can be loaded with data from the program address register which is how the jump instructions are implemented.

  • Program Address-Register

This register is a latch used for temporary storage of an address which will be loaded into the program counter during a jump instruction. The input data to this latch can come from either the program ROM or the scratch-pad RAM.

  • Input Selector

The input selector is used to read the state of one of the 24 input lines into the selected accumulator. There are 16 primary inputs and 8 secondary inputs. During an input instruction the upper 11 bits of the accumulator are set to zero while the least significant bit reflects the state of the input line. All input lines have pull up resistors on them so that they will read high if they are left unconnected.

a

Page 25
  • Output Selector

The output selector is a bit addressable latch used to control the 8 output lines. During an output instruction the selected output line is set to the complement of the least significant bit of the accumulator. The output lines are used to control the audio board, display intensity and the mechanical coin counter.

  • Display Registers

The display registers are the interface between the processor and the display driver circuits. These registers are latches into which the contents of the accumulators can be stored. The outputs are tied to D/A converters which provide the input voltage to the display deflection amplifiers.

TABLE 6-1. BLOCK NUMBERS AND COMPONENT I.C.

  • T-2, R-2, N-2
  • S-4, P-4, M-4
  • T-4, R-4, N-4
  • N-6, M-6, L-6, N-9, M-9, L-9
  • N-11, M-11, L-11
  • N-14, M-14, L-14
  • J-12, 1-12
  • H-12
  • S-13
  • U-7, R-7, T-7, P-7, U-9, T-9, U-11, T-11

ll. 1-13

  • A-8, G-10, F-10, G-14, F-14, E-14, D-14, C-14
  • E-6, D-6, E-8, H-8, G-8, F-8
  • $-9, R-9, P-9
  • S-11, R-11, P-11
  • P-13, R-13
  • E-4, D-4, C-4
  • F-2
  • S-2, R-2, M-2
Page 26

6-8 ACCUM.

SELECTOR

DISPLAY

REGISTER

SECONDARY

ACCUM

@ ADDRESS

FROM

ARITHMETIC To

ADDRESS. COUNTER TO GAME

UNIT © sue |

Eb ore SEL STORA SELECTOR & SELECTOR

i © REGISTER (0) INPUT

OUTPUT

ADDRESS

2)

ROM DATA

LINE COUNTER 2) SYSTEM SEQUENCER © INSTRUCTION

o) ROM MEMORY

Page 27

C. AUDIO BOARD

CIRCUIT DESCRIPTION AND TROUBLESHOOTING GUIDE

GENERAL INFORMATION

The following section describes the theory of operation for the Armor Attack audio board. The appendix contains block diagrams of the audio board. The theory of operation of each block will be described along with test techniques to enable effective troubleshooting.

An asterik (+) to the left of a title of a section indicates a detailed discussion that will be used elsewhere in the section.

DEFINITIONS

TTL (Transistor - Transistor Logic) compatible levels are defined as follows:

  • A TTL “‘low”’ or logic O is any voltage less than 0.8 volts.
  • A TTL “high” or logic 1 is any voltage greater than +2.0 volts.
  • A voltage within the range of 0.8 to 2 volts on any logic point indicates a bad part or an open input.

VCO: Voltage Controlled Oscillator CCA: Current Controlled Amplifier IC: Integrated Circuit (chip)

NOTATION

A particular pin of an IC (Integrated Circuit) is denoted in the text by first the chip designation and then the pin number—e.g. 1C25-10 means pin 10 of IC 25.

dumper patches W1 thru W13 are sections of traces on the audio board designed to be cut in order to isolate a section of circuitry for test purposes. Be sure to cut between the two eyelets, one round and the other square. The orientation of these pads is the same on the board as on the schematic diagram. Repair by adding a short jumper wire into the holes provided.

6-9 DO NOT repair any traces by adding a blob of solder at the cut. This will cause intermittent operation.

CAUTIONS

NEVER connect pin 5 of a CA3080 (CCA) directly to ground or any voltage other than -15 volts. Failure to observe this rule can cause the IC to explode (also known as the plastic pop-corn effect).

NEVER connect a TT! output to +5 volts. The plastic pop-corn effect applies here also.

TEST EQUIPMENT

For troubleshooting this board you will need:

  • V.O.M.
  • logic probe - not necessary, but recommended
  • several jumper wires with ‘‘E-Z2’”
  • an oscilloscope - not necessary, but recommended

TROUBLESHOOTING

All VCO outputs will measure 13 to 15 volts AC with a VOM (volt-ohm meter).

All 555 multivibrator outputs will measure 1.5 to 3 volts AC with a VOM.

INPUT CONTROL CIRCUITRY

(refer to block diagram 1)

IC1 and IC27 are schmitt-trigger inverters that clean up digital information arriving at connector J2 on pins 11, 15, & 16. The CPU board controls all sound generation by supplying digital data pulses through 16 pin connector J2. [C2 and 1C3 latch this control information on the board as follows—

Page 28

IC2 (74LS164) is an 8-bit serial to parallel shift register. Data in the form of a bit stream moves from connector J2-16 through IC1 and into pin 1 of IC2. Pin 8 receives clock pulses from the CPU via J2-15. Each pulse causes a single bit of data present at pin 1 to be transfered successively down the line to outputs A thru H. When the eight output ports are filled, IC3 (74LS377) swings into action. The outputs of IC2 are tied to the inputs of IC3 (1D-8D). When IC3 receives a load pulse on pin 11 thru connector J2-11, the data present on each of its inputs is transferred straight across to its outputs ports (1Q-8Q). Now data which entered on one channel thru connector J2-16 is available for use in the 8 channels of latch IC3.

TEST PROCEDURE

To verify proper operation of IC1, disconnect 16 the pin ribbon cable connector, J2 and decrease volume. Check IC1-2 with a logic probe, scope, or meter. It should read high or 2.4-5vDC (logic 1). Repeat for IC-11 and 1C27-6.

With a test lead, ground IC1-13. The output, 1C1-2 should now read low or (0-6.7) vdc, logic 0. Repeat for the other two pairs of schmitt-trigger circuits.

To verify proper operation of C2, load all lows into its output ports by tying IC-13 to ground. With another test lead connected to ground tap IC2-8 about 10 times. Output A thru H should now all read low. At this point, tap IC3-11 with the ground lead. Outputs 1Q- 8Q should now all read low.

Repeat the above procedure, but remove the ground lead from IC1-13. This should load all highs into all the output ports. This completes all the tests.

At this point the volume control may be turned up. No sound should be heard.

QUICK CHECK PROCEDURE

At this point all of the sounds generated on the audio board can be tested one at a time. Follow the above procedure for loading all ‘ones’ into the input control latch (IC3).

6-10 TABLE 1.

Table of Test Points for the quick check procedure. TABLE 1 Sound Test Ground/ Tap/ Point Open _Hold

Chopper J2-14 G T

Beepd2-13GT
Tankd2-12GH
also1C3-19GH
Tank Fire1C3-2GT
HiExplosion1C3-5GT
Jeep Firing1C3-6GT
Lo ExplosionIC3-9GT

Using a test lead ground the test points shown in table 1 to activate the desired sound. Some sounds on the test point e.g. explosions. To fully exercise the tank sound refer to it’s troubleshooting procedure.

NOISE_ GENERATOR

(refer to block diagram 2)

The noise generator circuitry is composed of IC17, a digital noise generator, a DC blocking network C21 and R26, and a voltage follower, IC18. Both outputs have a minimum amplitude of 11.5V P-P, with the waveform at 1C18-6 centered about ground.

TEST PROCEDURE

Check for proper amplitude signal at outputs (IC17-3 & 1C18-6). 1C18-6 will read approximately 2.5V RMS or 11.5 Vp-p.

  • TANK FIRE SOUND

(refer to block diagram 2)

This sound is activated whenever the tanks shoot. The basic components of this circuit are white noise, from the noise generator, a low pass filter, a current controlled amplifier (CCA), an envelope control circuit, and a voltage switch.

Page 29

LOW PASS FILTER

The output of the noise generator circuit is fed into the low pass filter, R34-38, C23-24. The filter output is then fed into the CCA 1C19-2 and 3.

CURRENT CONTROLLED AMPLIFIER (CCA)

IC19 can be imagined as an amplifier that generates acurrent waveform characteristic of the voltage appearing at pin 2. The strength orgain of the output current (IC19-6) is proportional to the current injected into pin 5 via R33 (refer to Fig. 1, pg. 6-16).

ENVELOPE CONTROL

R33 controls the amount of current injected into pin 5 of the amp and the RC time constant of R33 and C22 determines the envelope or decay time of the output waveform.

VOLTAGE SWITCH

The circuit is turned on by switching a low level on the base of Q2. This pulls the voltage up to the emitter of Q3 from -3.5v to +1.9v forward biasing Q3 and allowing it to inject current into the CCA.

TEST PROCEDURE

With J4 disconnected from the CPU board load all ‘ones’ into the output latch (IC3), (refer to input control circuitry), the junction of R27 and R28 will read about 5vdc. Grounding this point should cause the collector of Q2 to swing from -3.5v to almost 4.7v, the emitter of Q2 should remain at a constant 5vde. The upward voltage swing on the collector of Q2 should turn on Q3 and cause it’s colllector to rise from about -14.3 to about 5vdc. If, for any reason the voltage switch circuit is suspect, it may be eliminated by cutting W1 and tapping a grounded test lead to the square pad of W1. In either case a roar should be heard in the speaker. If this is not the case, verify that the noise generator is functional and that the tank firing circuit is receiving noise at R34. If any of the following sounds work, (see quick check procedure) lo explosion, chopper, jeep firing, or hi explosion, replace IC19. If none of the above operate, perform a check of the voltage follower circuit (see voltage follower). If the

6-11 voltage follower is operating correctly, one of the other CA3080’s may be shorted. To isolate a. y of the CA3080’s whose outputs feed the voltage follower, you may cut their output pin, pin 6, and use a test lead to connect the output of the CA3080 to the input of the voltage follower circuit, IC25-3. Don’t forget to exercise the appropriate sound.

Using the above procedure the offending CA3080(s) can be located easily.

VOLTAGE FOLLOWER

(refer to block diagram 1)

R90 converts the total current output of all the CA3080’s to a voltage. Since this is a high impedance point IC25 is used to ‘‘beef up” the signal on the top of R90, before feeding it to the pot driver (IC26).

TEST PROCEDURE

If any of the following, lo explosion, chopper, jeep firing, or hi explosion sounds, work it’s pretty much a safe bet that IC25 is ok. However if none of the above sounds work the test procedure is as follows: cut IC25-3 and apply a known good signal to [C25-3, on the chip itself not the board. NOISE from 1C18-6 isa good choice. Observe the output (IC25-6). If the input control latch is set-up properly, so that no sounds are on, the NOISE signal will be heard in the speaker.

LO EXPLOSION

(refer to block diagram 2)

The lo explosion is heard whenever a missile strikes a wall. The technical description is identical to that of the tank firing sound. The differences between the two circuits are different component values in the low pass filter and envelope control circuitry. These are for a different frequency response, amplitude, and decay time.

TEST PROCEDURE

See test procedure for tank firing sound.

Page 30

CHOPPER SOUND

(refer to block diagram 3)

The chopper sound is heard whenever the chopper appears on the screen. For a technical description see the technical description on the tank firing circuit. The differences between the two circuits are different part values in the low pass filter and envelope contro] circuitry. It should be noted that there is no capacitor in the envelope control circuit. This gives the chopper sound a fast attack and decay. Also note that there is no oscillator on the audio board for this sound. The ‘‘blade rate”’ is controlled entirely by the CPU board.

TEST PROCEDURE

See test procedure for tank firing sound. The only difference here is that the chopper sound is enabled by grounding 1C27-3, it is not driven off the latch, IC3.

JEEP FIRING AND HI EXPLOSION SOUNDS

{refer to block diagram 3)

The jeep firing sound occurs whenever the jeep shoots. The high explosion sound occurs when a tank is struck for the second time. It also occurs when either a jeep or the helicopter is hit.

The technical description of these sounds is identical to that of tank firing sound with one major difference. These two sounds share a common low pass filter and a CCA (IC22).

TEST PROCEDURE

See the test procedure for the tank firing circuit. The only additional trouble shooting step required here would be to cut both W4 and W5 when attempting to enable 1C22. Grounding the square end of W5 should yeild a louder noise in the speaker than when grounding the square end of W4.

BEEP SOUND.

(refer to block diagram 3)

The beeper generates the morse code sound, which occurs at the beginning and end

6-12 of the game. It also occurs whenever a new jeep arrives on the screen.

The morse code sound is generated by a gated oscillator consisting of [C23, R81-83, C35 and C37. The CPU enables this oscillator, a 435 cycle note, J2-13. The output of the oscillator, a 435 cycle note, is coupled to the summing junction via R83 and C36.

TEST PROCEDURE

With the cable removed from J2 both the reset input 1C23-4 and the output 1C23-3 of the gated oscillator should be low. Ground J2-13. The reset input of the gated oscillator should go high and a 435 KHz rectangular waveform should appear at 1C23-3.

TANK SOUND

(refer to block diagrams 4 and 5)

The tank sound is a composition of two sounds, the tank motor sound and the tread squeak sound.

The tank motor sound is generated by a gated oscillator, several digital division circuits, a mixer and a shaping network.

The generation of the tank sound originates at the gated oscillator consisting of IC6, R2-3, Cll and C12. The CPU enables this oscillator with a low level on J2-12. The output of the oscillator, a pulse train with a period of 136 micro-seconds is fed to a programmable divide by N circuit, after squaring by IC1.

  • PROGRAMMABLE DIVIDE BY N CIRCUIT

The programmable divide by N circuit consists of IC8 and 1% of IC9, a nand gate. When IC8-9 is pulses low the four bit number on the D, C, B and A inputs is transferred to the outputs Q(d) thru Qa), respectively. Since this is an “‘UP”’ counter every time the clock input is struck with a positive transition the outputs of the counter will increment until a count of 15 is reached, all outputs high. At this time the carry output IC8-15 will go high causing the load input IC8-9 to go low. The load input will be recognized on the next positive transition of the clock, thereby causing the cycle to repeat.

Page 31
Note that this circuit will not function if all inputs to the counter, TS0+ thru TS3+, are all high. Refer to table 2 for a listing of input codes versus division rates.

TABLE 2

Table of frequency selection inputs v.s. output frequency and period for the programmable divide by N circuit. Frequency input = 7.35 KHz, a period of 136 micro-seconds

All pins noted are IC8.

seshecnase inputs---------- ----------outputs----------

654315

1S3+ TS2+ TS1+ TS0+ FREQUENCY PERIOD DIVISION micro-seconds RATE

1111—ILLEGAL~
0111833Hz12009
10111.47KHz6805
11012.5KHz4003
11103.7KHz2702

The operation of the divide by 13 circuit consisting of IC11 and 1/6 of IC1 is identical to that of the divide by N circuit, the only difference being the fixed division rate. Note also that the output of this circuit is taken from the Q(d) and not the carry output.

IC10 is utilized as a divide by 16 circuit.

Note that, whereas the outputs of both IC8 and IC11 change on the positive transition of the clock, this output IC10-6 alternates only on the negative edges of it’s clock, IC8-1.

The outputs of both the divide by 16 and the divide by 13 circuits are mixed at IC9-9, 10. The mixer output 1C9-8 is fed to 1C10-13 where it is divided by two. This last division by two insures that the waveform fed to the shaping network is always a squarewave.

The shaping network consisting of R6, R7, C13 and C14 preforms a bandpass function on the motor sound before it is sent to the summing junction of the preamp.

6-13 TANK TREAD SQUEAK

(refer to block diagram 5)

The tank tread squeak is generated by a gated binary counter, ‘‘wired nor’’ function, several low leakage switches, a summing and filter network, VCO, bipolar to TTL converter, a gated octive adder and a pair of inverters.

The gated binary counter, IC13, is enabled by the compliment of the TANK EN+ signal. It’s clock input IC13-13 is fed by the output of the divide by 16 circuit, [C10-6, in the tank motor sound. Only the divide by 16, IC13-8, and divide by 8 outputs, IC13-9 are used.

Both outputs drive three Low Leakage Switches, (LLS). Two of these are driven directly. The last enabled via a ‘‘wired nor’ function consisting of two open collector inverters IC7-5, 6, 10 and 11. The output of the ‘‘wired nor’’ function is low IC7-6 and 10, if either of its inputs IC7-5 or 11 is high.

LOW LEAKAGE SWITCH

The first Low Leakage Switch (LLS) is composed of Q14, Q15 and R95 thru R99. With IC13-8 high the base of Q14 rests near +5 volts. Due to lack of base of Q14 is cut-off, causing it’s collector voltage to drop to -3.5 volts. Q15 now sees a severe reverse bias and responds with almost an ideal open circuit collector to emitter.

The first LLS is enabled by a low on the divide by 16 output of the gated binary counter, 1C13-8. When IC13-8 goes low the base of Q14 drops to about 4.3 volts, turning it on, and causing the collector to rise to 4.7 volts. Q15 responds to this forward base drive by grounding it’s collector.

The three Low Leakage Switches drive the VCO IC15-5 via a summing and filtering network composed of R19 thru R23 and C18. This network of passavie components converts the on and off states of the three Low Leakage Switches to a single time varying analog signal.

This analog signal at the top of C18 is injected into IC15-5, the control voltage pin of the VCO. As the control voltage ramps between +12vdc and +14vdc the squarewave

Page 32

output of the VCO will ramp down in frequency from 27khz to 23khz. The output of the VCO (IC15-3) is then fed into the Peak-Peak to TTL converter. A 5v p-p squarewave enters the clock input of the Gated Octave Adder IC13. The outputs are then added together and sent on to the summing junction. The sound is enabled by bringing 1C13-2 to a low level.

TEST PROCEDURE

To troubleshoot the tank sounds load all ones into the output latch IC3, refer to Input Control Circuitry.

The programmable divide by N circuit may be checked by grounding the inputs IC8-3 through 6 singularly. Refer to table 2 for

correctfrequencyreadingson the out-

put 1C8-15.

Ground IC27-13 and IC3-19. Using table 3 and an oscilloscope, verify the timing of all the digital division circuitry in the tank motor sound and the gated binary counter in the tread sweep circuit. Both the input, IC10-13 and the output, IC10-11 of the divide by two circuit posses considerable ‘‘jitter’’, activity is observed at these points they are probably ok.

Table 3 Table of frequency and period readings for the tank sounds. TEST SETUP: IC8-4, 5 and 6 high, IC8-3 low, J2-12 low. Ic___PIN PERIOD _ FREQUENCY

63136 micro-sec.7.35KHz.
82136 micro-sec.7.35KHz.
815270 micro-sec.3.7KHz.
11113.5 milli-sec.285Hz.
1153.5 milli-sec.285Hz.
13870 milli-sec.14Hz.
13935 milli-sec.28Hz.
7670 milli-sec.14Hz.

6-14 The operation of the Low Leakage Switches may be verified as follows; ground IC27-13 and IC3-19. Remove all other grounds that may be attached. The bases of the pnp transistors, Q14 for example, should be swinging between 4.3 and 5 volts, small but ok. The collector of the same transistor should pulse from almost 5 volts down to -3.5 volts. If a ‘scope is available check the output of the pnp transistor, it should go from a bit above ground to at least 8 volts. If a ’scope isn’t handy and the pnp transistor is suspect, cut the troubleshooting jumper, W11 in this case, and temporarily install a resistor, 2K to 20K, between +15 volts and the round pad of the jumper. Short the pnp transistor base to collector. Using a VOM meter the collector of the pnp transistor. It should read +15 volts. Ground driver circuit, IC13-8 in this case. Anything above 0.3 volts at the collector indicates a bad npn transistor.

To check the VCO, peak to peak to TTL converter and gated octave adder, remove the ground from IC27-13. Ground IC13-2. Using table 4 and a ’scope, check the outputs of the VCO and the gated octave adder.

Table 4 Table of frequency and period readings for the tank squeak sound.

TEAT SETUP: 1C27-13 high.

IC PIN PERIOD FREQUENCY (micro- (KHz) seconds)

1534223.8
1338412
1341685.95
1553362.97
Page 33

QUTPUT AMPLIFIER

(refer to block diagram 1)

The output amplifier section consists a preamp and volume pot driver IC26 (TLO81), main driver amp IC24 (TLO81) and speaker drive transistors Q12 and Q13.

1C26 drives the external volume pot located on the coin door and its associated cable. If little or no volume is heard, meter the pot wires between J1-8 and J1-3. The resistance should vary as the pot is rotated. If the audio

6-15 is at maximum volume regardless of the pot position, suspect an open lead between ground and the pot lead connected to connector J1-1.

The final drive is a non-inverting amplifier circuit containing IC24, Q12 and Q13. Observe the waveform at the speaker wire which is the emitter junction of Q12 and Q13. If the upper half of any sound waveform appears clipped, suspect Q12. For the lower half, Q13 is the suspect. For no audio meter Q12 and Q13 out of circuit and look for burned resistors R122 and R124. Also check diodes D6 and D7 at this time.

Page 34

+V

CONTROL

CURRENT AMPLIFIER

FIGURE ONE

Page 35

INPUT CONTROL CIRCUITRY

TANK FIRE —

HI EXP —

JEEP FIRE—

LO EXP -

TS3+ aan Ts2+ SELECTS TO TS1+ BLOCK DIAGRAM TSO+ FOUR SCHMITT TRIGGER

BUFFER

OUTPUT CIRCUITRY

SUMMING JUNCTION TANK MOTOR

TREAD SQUEAK

VOLTAGE FOLLOWER BEEPER PRE AMP FROM BLOCK DIAGRAMS 2,3,4,5

TANK FIRE

LO EXP

CHOPPER VOLUME IC 24,Q12,Q13

jeer FIRE CONTROL ; FINAL AMP

LOCATED | HI EXP N TO

ON COIN

SPEAKER DOOR =

BLOCK DIAGRAM ONE

6-17

Page 36

LOW PASS FILTER R34-38,C23,C24

TANK FIRE

Ic 3-2

LOW PASS FILTER R46 —-—50,C26,C27

LO EXPLOSION

ENVELOPE CONTROL R33,C22

TO VOLTAGE FOLLOWER (BLOCK ENVELOPE| piagRAM CONTROL ONE) R45,C25

NOISE TO BLOCK DIAGRAM THREE

NOISE GENERATOR IC 17,1C 18

BLOCK DIAGRAM TWO

6-18

Page 37

LOW PASS FILTER R58-61,R94,C29,C30

CHOPPER

LOW PASS FILTER R69 — 73,C32,C33 i

VOLTAGE FOLLOWER JEEP (BLOCK NOISE 1C3-6 |VOLTAGE (FROM —_—__»> DIAGRAM BLOCK u ONE)

DIAGRAM TWO) HI EXPLOSION IC3-5 ——+»| switcu oe

MORSE CODE Ic 27-8 | OSCILLATOR ——_—_ > 123 R81—R83 BEEP EN + C35-C37 SUMMING JUNCTION (BLOCK DIAGRAM BLOCK DIAGRAM THREE ONE)

6-19

Page 38

TANK MOTOR SOUND

BAND PASS NETWORK R6,R7 C14,C13 TO SUMMING JUNCTION (BLOCK DIAGRAM ONE)

DIVIDE BY 16 CLOCK

TO BLOCK DIAGRAM FIVE

TS(O-3)+ FROM BLOCK DIAGRAM EAE GATED ONE ———> OSCILLATOR —_—> C6 FROM R2,R3 BLOCK c11,C12 DIAGRAM ONE

BLOCK DIAGRAM FOUR

6-20

Page 39

GATED OCTAVE BIPOLAR TO

CONVERTER Ri4—RIB Q1,D5,D8 C18,C19 R4,R12,R13,C16 ——

SUMMING AND FILTER NETWORK R19-R23,C18

LLS LLS LLS Q14,Q15 Q16,Q17 Q18,Q19

WIRED “NOR” FUNCTION Ic7 DIVIDE BY 16 CLOCK FROM BLOCK DIAGRAM FOUR + 1C13 GATED > BINARY COUNTER

TANK EN+

1c 27-12

6-21 BLOCK DIAGRAM FIVE

Page 40

SECTION 7

TROUBLESHOOTING

UNIVERSAL BENCH TEST

CONFIGURATION SYSTEM TEST CONSIDERATIONS

The components depicted in figure A represent the integral elements and interconnects necessary to effectively bench test the Cinematronics vector display video game system. The configuration is universal in that the game logic board A, display assembly B, and the power supply D are consistent from game to game. Audio board C varies in design for each new game though maintaining the pinout of its input power molex plug. Player control ribbon cable 3 terminates at the player control panel elements of each game (i.e. Joystick, Fire & Thrust buttons, Coin Acceptor Mechanism, etc.)

POWER INTERCONNECTS

The power supply D provides all voltages necessary for game operation.

Logic board drive is +5 volts + 5% applied to pin 10 of the input power molex plug, & ground enters the logic board thru pin 4 to pins 1,5, and

  • The logic board will free run in the game attract mode with proper power applied.

The audio board accepts +25 volts on pin4 and -25 volts applied thru pin6 to pin 8. Ground enters pin 7 and is trace connected to speaker return pin 5. Pin 9 accepts +5 volts DC.

Power for the display is +25 volts thru pin 6 of its molex plug to pin 5 and -25 volts onpin 8. The CRT filament voltage of 6.3 V.A.C. enters the display electronics through pins 1 & 7 viaa twisted pair of wires from the supply. A full wave rectified, unfiltered spot kill level of approximately +25 volts is applied to pin 14. The assembly is grounded thru pin 15 to pin 12.

7-1 As previously mentioned, the logic board A will free run in the particular game attract mode solely with +5 volt applied. Ribbon cables 1 & 2 are output lines and can be removed without affecting the free-run mode. Ribbon cable 3 is an input line and can also be removed for test purposes while free running.

The audio board C can be effectively diagnosed with proper power applied and a speaker. The logic board generates most sounds by grounding various control lines through ribbon cable 2. The cable can be removed and game sounds can be generated by tying these lines low temporarily with a jumper wire. Refer to the appropriate audio board schematic and theory of operation section.

The display assembly cannot be powered up without data cable 1 from the logic board connected. With the cable open or improper data being fed from the logic board, the circuit breakers CB1 & CB2 on the power supply will trip indicating a load in excess of 3a being drawn from the +25 and -25 volt lines. Testing of the monitor requires a functional logic board. While troubleshooting a no display condition, it is recommended to remove the 8 pin molded female plug from the neck of the CRT to protect the phosphor on the tube face from being burned by a high intensity spot.

TEST EQUIPMENT

For most test purposes, a wideband oscilloscope and a digital or analog multi-meter is adequate. Also, a tri-level logic probe for verifying the presence of digital information is recommended.

Testing and troubleshooting of the logic board is the least straightforward aspect of bench test. However, Cinematronics has

Page 41

developed a logic board exerciser to be used in conjunction with a signature analyser that allows effective troubleshooting & repair with a minimum knowledge of microprocessor theory and operation. The exerciser puts a 4 bit alphanumeric code on each IC leg of each chip on the CPU board which then can be probed & read with the signature analyser to verify proper operation. Contact the customer service department at Cinematronics for details. TEST PROCEDURES

The first step in effective bench testing is to review the system theory of operation included in the manual. Discussed are principles from the mathematical concept of vector systems to the actual hardware techniques employed in generating a vector video game display. For specific troubleshooting procedures, refer to the symptom-remedy diagnostic chart included in the manual.

Page 42

MONITOR ASSEMBLY 38-10633-01 AC.CORD 87-10845-03

34 PIN MAIN WIRE ASY. RIBBON CABLE 87-10877-01 POWER 87~10848-01 SUPPLY 82-10842-XX

8 OHM AUDIO BOARD SPEAKER 38- 11141 -01 71-10834-01

16 PIN RIBBON (TO PLAYER CONTROLS)

CABLE 26 PIN RIBBON CABLE 87-10847-01 87-10846-01

LOGIC BOARD 38- 11142 -01

UNIVERSAL

BENCH TEST °

CONFIGURATION

7-3

Page 43

MONITOR PROBLEMS

Here is a systematic guide to trouble shooting a monitor that blows breakers. Monitor must be connected to a good CPU. Check for burned components. The first thing we want to do is be able to power up the monitor without blowing breakers - then do trouble shooting.

POWER OFF. Unplug yoke from monitor board. Unplug socket from CRT. POWER ON.

If breakers blow: POWER OFF. See 1.

If breakers hold: Check outputs of -15v, +15v, and +5v regulators. Output must be within + 0.5 volt tolerance.

A. Use O-scope to check deflection circuits for proper signal. Imv/div time base is a good scope setting. Between DAC-80 output and input of Q101 or Q201, signal amplitude is about +3 volts peak. DC component should be less than +200 mv. Too much DC component will trip breakers. If signal into Q101/Q201 is good, problem is in transistorized deflection amps. With yoke disconnected, a good amp will put out an odd looking “square wave’’, swinging between + 25 volts. To check a bad deflection amp, check all transistors. Look for burned R118, R119, R113, R117 or R218, R219, R213, R217. R115, R116, R120, R121 may open with no burn marks. For test purposes, protection transistors Q106, Q107, Q206, Q207 may be removed from the circuit and amplifier can be powered up. Always replace protection transistors before returning monitor to normal service.

  • POWER OFF. Unplug heat sink wiring harnesses from monitor board. POWER ON. Breakers blow: POWER OFF See 2. Breakers hold: one or more of Q110, Q111, Q210, Q211 are shorted. Damage elsewhere is likely. Follow procedure at A.
  • Problem is most likely Video High Voltage module. Unplug from board and POWER ON. Breakers hold: replace or repair Video power supply. Breakers blow: Maybe a shorted tantalum capacitor. Or call us.
Page 44

TABLE 7-1. TROUBLESHOOTING GUIDE

PROBABLE SOLUTIONS

Listen for audible “clatter” from the deflection yoke on the CRT neck. If the clatter is present, deflection circuitry is working and the problemisin the intensity circuit. PROBLEM

No Picture

No high voltage.

If game audio is present, the CPU board is functional and the problem is in the monitor. If the audio is distorted or absent, the CPU board is suspect. If CPU board is equipped with red led near the input power plug, verify that it flashes once when power is applied and remains off thereafter. If no LED, verify that C8 pin 6 is constantly low with a voltmeter.

Check the neck of the CRT for a glowing filament. If there is no glow, check the brown & black twisted pair of the CRT plug for 6.3 volts AC.

Be sure all connections to the CPU board and monitor are firmly seated,

Connect a scope to the yellow wire leading to the CRT connector. Set brightness full clockwise. There should be an 80-100 volt DC base with pulses dropping down to a 40 volt level. If no pulses, probe IC7 pin 4 with a scope and observe data pulses. If present, check Q2 & Q3 with an ohmeter or transistor tester.

Check cathode of D5 for a full wave rectified, unfiltered voltage signal floating at +25 volts.

Check seating of CRT plug. Remove and probe with scope to verify presence of proper signals.

Check IC1. Check for open yoke windings with ohmeter. Narrow Line on Display

Check for bad solder & crimp connections to yoke wires. Verify continuity between display board and heat sunk power transistors Q110, Q210, Q111 and Q211. Check Q110, Q210, Q111, Q211 with ohmeter or transistor tester. Inspect solder connections on circuit board molex connector socket pins.

Half Picture Left Half: Check Q206, 208, 210 Right Half: Check Q207, 209, 211 Top Half: Check Q107, 109, 111 Bottom Half: Check Q106, 108, 110

Page 45

TABLE 7-1. TROUBLESHOOTING GUIDE (Continued)

PROBLEM PROBABLE SOLUTIONS

Check solder connections on heat sink molex plugs J3 & J4.

Check diodes CR109, 110, 111 Check diodes CR209, 210, 211

Check transistors Q105, Q205

Check resistors R116, R216.

No Brightness Control Check intensity pot R111 for open wiper or internal short. Check for open capacitor C17. Check for bad solder connections to R111.

Picture on Display Jitters Replace analog switch IC1.

Check size pots R109 and R209 for wiper noise by turning briskly while observing the screen. Readjust for proper screen size.

Check for bad solder connections on R109 & R209.

Check DAC IC101 & IC201 for bad solder connections. 3.

Insure that all molex connectors are properly seated.

Suspect High Voltage An accurate High Voltage meter will read close to 16KV if high voltage too high/too low is good. Self-contained HV meters vary widely in accuracy. If +90 and +400 volts out of high voltage supply are good, chances are 16KV is good. If +90 or +400 volts are bad, repair or replace high voltage supply.

, Check IC-7 pins 2, 4. Dotted Display Verify proper operation of IC1.

Check for proper +25 and -25 volts DC. Check operation of DAC’s IC101 and 1C201. On logic board, check I 8 pin 2 for pulses. Verify presence at analog switch. No Audio Check for open speaker coil. Check transistors 2N6292 and 2N6107 and nearby output components on audio board with chmeter or transistor checker. Check 7815 and 7915 outputs. Check for open wiper on volume control mounted on inside of coin door.

Refer to audio board theory of operation and troubleshooting guide.

Replace F2 on logic board.

Page 46

TABLE 7-1. TROUBLESHOOTING GUIDE (Coniinued)

PROBLEM PROBABLE SOLUTIONS

Coin Counter Check 2N6292 transistor on logic board with ohmeter or transistor is Inoperative tester. Verify proper operation of A4 by grounding A4 pin 1. Coin counter should click.

Disconnect coin counter molex connector. Measure DC voltage on red wire. Meter should read +25 volts DC.

Gives No Credits Tie E4 pin 12 to ground. If credits fail to appear, replace E4. If credits appear, disconnect logic board ribbon connector J3. Measure +5 volts on Aé pins 1 & 5. If missing, replace pull up resistor pack C2.

Alternately ground A4 pins 1 & 5. If credits appear, problem is in switches on coin door. Verify proper coin door microswitch operation.

Reconnect J3. Observe A4 pins 3 & 6 alternately while depressing microswitch lever on coin mechanism. Pins 3 & 6 should change states. Replace A4.

Replace F2 (74LS259) on logic board,

Player Control Button(s) Refer to player control schematic in APPENDIX. Inoperative Verify with ohmeter proper closure of player control leaf blade switches.

Remove J3 connector. Measure +5 volts on D4 - 1, 2, 3, 4, 12, 13, 14, 15. If missing, replace D4. Replace pull up resistor pack D2.

Measure +5 volts on C4 - 1, 2, 3, 4, 12, 13, 14, 15. If missing, replace C4. Replace pull up resistor pack C2.

Coin up a game and, with J3 disconnected, ground aforementioned pins on C4 & D4. If display responds problem is in continuity from J3 to player control switches.

7-7

Page 47

SECTION 8

SUGGESTED PARTS FOR STOCK

The following parts fail most frequently:

MONITOR

LF13331 — Analog switch 2N5876 — PNP output transistor 2N5878 + — NPN output transistor 2N5320 — PNP driver transistor 2N5322 — NPN driver transistor 7406 — IC inverter package 2N5550 — NPN transistor 140 volt BVceo 7805 — +5 volt regulator IC 7815 — +15 volt regulator IC 7915, — -15 volt regulator IC

cpu

74LS259/DM8334 — IC8 bit latch 74LS32 — ICor gate DROM1 — IC PROM 20101 A2 — ICRAM256x4

AUDIO.

2N6107 — PNP output transistor 2N6292 — NPN output transistor TL081/LF351 — IC op-amp CA3080 — ICtransconduct. 74LS377 — ICoctal D flip-flop (also used in CPU)

The following parts don’t fail frequently, but are not readily available local electronic supply houses:

MONITOR

DAC-80 — digital to analog converter

CPU

Masked ROMS — set of four contain game program D ROMS (1-6) — custom made for CPU 25LS181 — ALU

8-1

Page 48

CINEMATRONICS SECTION 8

PARTS LIST

OVERALL ASSEMBLY

10-11215-01

DESCRIPTION PART NO.

38-11145-01 38-11208-01 38-10642-01

38-10633-01 38-10895-01 72-11211-01

32-10889-01 20-10871-01 20-10872-01 20-10864-01 20-10862-01 38-10897-01 38-10891-01 20-10865-01 22-10953-01 37-10893-01 20-10863-01 20-10866-01 20-10867-01 20-10879-01 20-10530-01 71-10834-01 21-10831-01 21-11203-02 21-11202-02 22-11199-01 22-11200-01 26-10588-01 01-10505-01 87-10877-01 22-10542-01 22-10543-01 22-10544-01 Cabinet Assembly Control Panel Assembly Circuit Panel Assembly (CPU and Audio Boards) Monitor Assembly (Display Board) Power Supply Assembly Operators Manual

CABINET ASSEMBLY

38-11145-01

Cabinet Coin Box Coin Box Cover Coin Box Handle Coin Box Tongue BKT. Coin Door Assembly Coin Meter/Vol. Cntl. Assy. Cover Plate Display Shield Interlock Switch Interlock Switch BRKT. Rail, Left Rail, Right Retainer, Plexiglass Grill, Speaker Speaker Bezel, CRT CRT Plexiglass (Screened) Upper Plexiglass (Screened) Decal, Side left right Fixture, Florescent Lamp Florescent Lamp Main Wire Harness Label, Patent Notice Label, Safety GND Notice Label, Unit Wired For: Meee eee

Page 49

eo DESCRIPTION = rT 25-10561-01_ | Wi ire Nuts 34-10903-01 Flat Braid 3/16”’ 35-10618-01 Terminal, Ring Tongue (Braid) 25-10554-01 | Carriage Bolt CN BX |3/16”-1%4”" plated 25-10552-01 Carriage Bolt SPK, P.S., CN DR |3/16’’-114” Blk Ox 25-10553-01 Carriage Bolt CNTL PNL |3/16’’-2”” Blk Ox 25-10551-01 Carriage Bolt MNTR |3/16’’-12”’ Blk Ox 25-10909-01 Carriage Bolt CN BX TNG|3/16’’-34”" 25-10558-01 | Hex Nut 25-10560-01 | Wing Nut 25-10566-01 Wood Screw Bx Dr 25-10568-01 Washer, Flat 25-10569-01 Washer, Flat 25-10572-01 | Washer, Lock

CONTROL PANEL ASSEMBLY

38-11208-01

32-11201-01 Control Panel, Wood 21-11106-02 Instruction Panel, Plex (Screened) 37-10623-01 Switch W/Mounting 37-10624-01 Button Assembly, Long 25-10559-01 Pal Nut 20-10879-01 | Retainer, Player Control 80-10840-01 Distribution P.C.B. 41-10645-01 Connector, Insulat. Displ. PCB 26 pin 87-10846-03 | Ribbon Cable 26 wire 41-10646-01 Molex, Wafer Fric. Lock 3 cir. 09-65-1031 25-10578-01 Swage Spacer 1/4’ 25-10567-01 Wood screw #6-1’’ Blk. Ox Box Dr. 25-10566-01 | Wood Screw #8-5/8”’ Blk. Ox. Box Dr. 87-10876-01 Switch Wire Harness Assembly 37-10957-01 Leaf Switch Replacement WICOF15- 0677-01 HWONNHHE ee

Page 50

CINEMATRONICS PART NO. DESCRIPTION MFGR. PART NO. =

20-10525-01 38-11142-01 38-11141-01 87-10847-01 87-10848-01 25-10571-01 25-10563-01

90-10860-01 38-10631-01 38-10958-01 38-10637-01 82-10841-01 25-10583-01 20-10869-01 20-10870-01 38-10628-01 25-10562-01 25-10563-01 25-10571-01 25-10557-01 25-10564-01 25-10568-01 25-10569-01 25-10565-01 20-10528-01 38-10632-01 21-11108-01 44-10715-01 22-10545-01 =

CIRCUIT PANEL ASSEMBLY

38-10642-01

Mounting Plate CPU P.C.B. Assembly Audio P.C.B. Assembly Ribbon Cable 16 pin Ribbon Cable 34 pin #6 Lock Washer Int. Th. 6-32-12” M.S. Rd. Hd. PH.

MONITOR ASSEMBLY

38-10633-01

CRT 19” Deflection Yoke Amplifier Monitor Assembly Test Yoke Assembly Keltron Video Power Supply Spring, CRT Mounting Bracket LH Mounting Bracket RH Display P.C.B. Assembly 4-40-12" M.S. Pan Hd. PH. 6-32-14” M.S. PanHd. PH. #6 Lock Washer INT. TH. 6-32 Hex Nut #6-1/)”” S.M.S. Hex Hd. #10-1” Wahser #10-1’’ Washer #10-Y2" S.M.S. Hex Hd. Chassis CRT Socket Assembly Overlay, Plastic (CRT) Analog Switch Label, Factory Adjust Only 19VARP4

® gs

a MEE OPA PRO WWWWH EEE

©

Page 51

CINEMATRONICS PART NO. DESCRIPTION MFGR. PART NO.

36-10622-01 63-10804-01

25-10582-01 35-11205-01 25-10564-01 25-10579-01 34-10608-02

20-10522-01 66-10822-01 66-10823-01 87-10873-01 87-10874-01 22-10546-01 45-10719-01 25-10563-01

40-10644-01 35-10615-01 35-10614-01 41-10657-01

82-10842-** 82-10842-40 82-10842-20 CRT SOCKET ASSEMBLY

38-10632-01

CRT Socket Capacitor .05mf 1600VDC

Heat Shrink Tubing (clear) Ring Tongue Terminal! 22 GA #6-1/’ S.M.S. Hex Hd. TY RAP Wire 18 AWG 9”

DEFLECTION YOKE AMPLIFIER

38-10631-01

Heat Sink Transistor Transistor Heat Sink Harness Long Heat Sink Harness Short Label, Warning Washer, MICA Greaseless 6-32-1/2”” Rd. Hd. Ph. M.S.

YOKE ASSEMBLY

38-10637-01

Yoke, Broy Molex, Female Pins Molex, Male Pins Molex, Receptacle 6 Cir.

POWER SUPPLY ASSEMBLY

38-10895-01

Power Supply National Power Technology CONDOR

8-5 Sprague 16PS-S50

2107-A 2N5876 2N5878

02-09-1118 02-09-2118 03-09-1063 WRHEENNN

Page 52

CINEMATRONICS, PART NO. DESCRIPTION MFGR. PART NO

COND AWE =

41-10883-01 41-10658-01 41-10049-02 41-10647-01 41-10648-01 35-10615-01 35-10614-01 35-10617-01 25-10579-01 25-10580-01

87-10845-01 35-10614-01

41-10650-01 35-10880-01 35-10617-01

25-10579-01

20-10868-11 38-10960-01 38-10961-01 25-10562-01 25-10556-01 25-10570-01

29-10590-01 65-10812-01 35-10615-01 41-10659-01 MAIN WIRE HARNESS ASSEMBLY

87-10877-01

Molex Receptacle 3 Cir. Molex Receptacle 4 Cir. Molex Receptacle 9 Cir. Molex Receptacle 12 Cir. Molex Plug 15 Cir. Molex Femal Socket Molex Male Pin Terminal, Female QK DSCT TY RAPS TY RAPS W/Eyelet 63/4 Wire A.C. Cord Terminal, Molex Male Pin

COIN SWITCH HARNESS ASSEMBLY

87-10876-01

Molex, Connector W/Lock 3 Cir. Molex, Female Crimp Terminal Terminal, Female Quick Disconnect .187-.032 Wire 5 Pcs. Tie Wraps

COIN METER/VOL. CONTROL ASY.

38-10891-01

Bracket, Coin Meter/Vol. Coin Meter Assembly Volume Control Harness Assembly #4-40-1/2”” M.S. Rd. Hd. Ph. HEX Nut 4-40 Washer, Lock #4

COIN METER ASSEMBLY

38-10960-01

Coin Meter Diode Molex, Female Pin Molex, Plug 3 Cir.

8-6 03-09-1038 03-09-1042 03-09-1093 03-09-1122 03-09-2153 02-09-1118 02-09-2118

T-18R

02-09-2118

09-50-3031 08-50-0106

T-18R

1N4003 02-09-1118 03-09-2038

Page 53

CINEMATRONICS PART NO. DESCRIPTION

51-10722-01 41-10659-01 35-10615-01 35-10614-01 25-10579-01

26-10589-01

20-10896-01 20-10868-01 25-10905-01 87-10876-01 87-10955-01 25-10556-01 25-10570-01 25-10563-01 25-10571-01 25-10557-01 22-10899-01

25-10579-01

44-10676-01 44-10677-01 44-10678-01 44-10679-01 44-10680-01 44-10681-01 44-10682-01 VOLUME CONTROL HARN. ASY.

38-10961-01

Pot. 10K Molex Plug 3 Cir. Molex Female Socket Molex Male Pin TY RAPS Wire Knob

COIN DOOR ASSEMBLY

38-10897-01

Coin Door Bracket, Coin Meter/Volume Cable Clamps 3/16”’ Wire Harness, Coin Switch Wire Harness, Volume Control Hex Nut Washer, Lock Int. Th. 6-32-1/2”’ Rd. Hd. Ph. M.S. #6 Lock Washer Int. Th. 6-32 Hex Nut Decal

SWITCH WIRE HARNESS ASY.

87-10876-01

Wire List TY RAPS

CPU P.C.B. ASSEMBLY

38-11142-01

LC. ALU L6, M6, N6 I.C. NAND Gate A4, A10, B4, J6 1.C. NOR Gate A6, D10, H8, K4 1.C. Hex Inverter B6, E12, ig 1.C, AND Gate C10, 16 1.C. NAND Gate B12, F4, L2 1.C. NOR Gate C12, D12, Fé

8-7 03-09-2038 02-09-1118 02-09-2118 T-18R

25LS181 74LS00 74LS02 74LS04 74LS08 74LS10 74LS27

Page 54

CINEMATRONICS PART NO. DESCRIPTION REF. DES. MFGR. PART NO. —+ 44-10683-01 44-10684-01 44-10685-01 44-10686-01 44-10687-01

44-10688-01 44-10689-01

44-10690-01

44-10691-01 44-10692-01

44-10693-01 44-10694-01

44-10695-01 44-10696-01

44-10697-01 44-10698-01 44-10699-01 44-10700-01 44-10701-01 44-10703-01 44-10704-01 44-10705-01 44-10706-01 44-10671-01 44-10675-01 44-10702-01 44-10667-01 44-10707-01 44-10708-01 44-10709-01 44-10710-01 44-10711-01 44-10712-01 38-11210-01

37-10625-01 69-10833-01 65-10811-01 66-10816-01 66-10825-01 .C. OR Gate .C. Quad D Latch .C. Mag Comparator -C. Exclusive OR : Dual J-K Flip Flop

. 1 of 8 Data Selectors “C. Quad Data Selector

. Binary Counter

.C. 8 Bit Shift Regist . 4 Bit Shift Regist

.C. Tri-State Quad . 8 Bit Latch

-C. Quad 2-Input Multi. -C. Octal D Flip Flop

-C. Dual 4 Bit Counter -C. NAND Gate . NOR Gate .C. Hex Inverter .C. AND Gate .C. OR Gate . Dual J-K Flip Flop

. Look Ahead Carry . Dual 4 in NOR Gate -C. Quad Comp. Output .C. Triple 3 in NAND -C. RAM 256x4 .C. PROM DROM 1 .C. PROM DROM 2 .C. PROM DROM 3 .C. PROM DROM 4 . PROM DROM 5 .C. PROM DROM 6 1.C. E-PROM I I se I I I I I 1, I. I I I I I I

I I

7 Pole Dip Switch Crystal 20 MHz Diode Transistor Transistor

8-8 Cc c

Cc. Cc

Cc Cc Cc Cc. Cc Cc ic .C. Quad 2 to 1 Data Sel. Cc Cc Cc c. Cc C. Cc Cc C. Cc. A12, B10, d2, K2 T9, U9 L9, M9, NO

A8, B2, B8, C8, G4, G8, J10 C4. D4, £4, F10 L11, M11, N11, P9, R9, $9,T11, ull C6, D6, E6, E10, F8, 114, P11, R1i, sii H6 G10, H12, N4,M4 P4, P13, R4, $4, Ta N2, R2, T2 F2

112, J12 M2, P2, R13, S2, $13, T13 H4, 14 A2, 110 H14 12, U2 Al4 B14, H10 G2, H2 G14 L4 F12 J4 G12 114,M14,N14 Fl4 E14 D4 C14 E8 J14

E2 Ll

Q2,Q3 Ql 74LS32 74LS75 74885 74LS86 74LS107

74LS151 74LS157

748163

74LS164 74LS194

74LS257 74LS259/ DM8334 74LS298 74S377

741.8393 74800 74802 74S04 74808 74832 748113 745158 748182 7425 74265 74810 2101A2 2085 2086 2087 2088 2089 2090 2732

1N914B 2N3904 2N6292 PEE EEE WRENN AD

Emme

Page 55

NO. CINEMATRONICS PART NO. DESCRIPTION REF. DES. MFGR. PART NO. == 63-10783-01 63-10785-01 63-10808-01 63-10810-01 53-10731-01 53-10732-01 53-10734-01

53-10738-01 53-10746-01 53-10753-01 53-10762-01 53-10779-01 35-10616-01 41-10655-01 41-10652-01 41-10653-01 41-10654-01 34-10612-06 36-10619-01 36-10620-01 36-10621-01

80-10837-01 53-10726-01 65-10814-01

53-10723-01 53-10724-01 53-10725-01

53-10726-01

53-10729-01 53-10731-01 53-10732-01

53-10733-01 Cap Disk .02mf 50V Cap Disk 680pf 100V Cap Tant Dip 3.3mf35V Cap Tant Dip 22mf 35V Resistor, 330 ohm 14W 5%C Resistor, 470 ohm 14W 5%C Resistor, 1K ohm %4W 5%C

Resistor 2.2K ohm 14W 5%C Resistor 10K ohm ¥/4W 5%C Resistor 30K ohm YW 5%C. Resistor 560K ohm 1/4W 5%C) Resistor Dip Pak 1K Test Points Molex, Wafercon 12 Cir Male Header PCB 16 Pin Male Header PCB 26 Pin Male Header PCB 34 Pin Jumpers, Socket, Dip 14 Pin Socket, Dip 16 Pin Socket, Dip 24 Pin

Printed Circuit Board Resistor, 100 ohm %4W 5%C L.E.D.

DISPLAY P.C.B.

38-10628-0.

Resistor, 15 ohm /4W 5%C Resistor 33 ohm %4W 5%C Resistor, 47 ohm YW 5%C

Resistor, 100 chm %4W 5%C

Resistor, 200 ohm 14W 5%C Resistor, 330 ohm YaW 5%C Resistor, 470 ohm 14W 5%C

Resistor, 820 ohm 14W 5%C

8-9 C1-C58 C59 C62 Cel R2, R3 RS R1, R4, R6, R7, R8, R9, R10, R11, R17, R18, R19, R20 R15 R13, R16 R12 R14 C2, D2

Jl J4 J3 J2 D8, 014 F6 D8, F14, U14 16, M6, N6, P7,R7, 17, U7

R21

R11, R215 R116, R216 R108, R130, R131, R210, R230, R231 R110, Ri17, R208, R217 R113, R213 R207 R1, R2, R4, R5, R19 R130, R230, R112, R212 09-18-5127 NOR NEHER HANH ENE

weweny

Page 56

CINEMATRONICS PART NO DESCRIPTION REF. DES.

53-10734-01 53-10736-01 53-10738-01 53-10740-01 53-10744-01 53-10746-01

53-10758-01 53-10766-01

53-10767-01 53-10768-01

53-10769-01 53-10770-01

53-10771-01 53-10772-01 53-10773-01 53-10774-01

53-10776-01

53-10777-01

53-10778-01

51-10720-01 §1-10721-01 65-10811-01

65-10812-01

44-10669-01 44-10672-01 44-10673-01 44-10674-01 44-10718-01 44-10714-01 66-10815-01

66-10816-01 66-10817-01 Resistor 1K ohm %4W5%C Resistor, 1.8K ohm “4W 5% Resistor, 2.2K ohm 14W 5%C Resistor, 3K ohm 1/4W 5%C Resistor, 5.6K ohm YW 5%C, Resistor, 10K ohm 14W 5%C

Resistor, 68K ohm 4W 5%C Resistor, 47ohm 12W 5%C

Resistor, 2.2K ohm #2W 5%C! Resistor, 8.2K ohm 12W 5%C

Resistor, 10K ohm ¥/2W 5%C Resistor, 2.7 ohm 1W5%C

Resistor, 360 ohm 1W 5%C Resistor, 10K ohm 1W5%C Resistor, 100 ohm 2W 5%C Resistor, .18 ohm 3W 5%C

Resistor, 1.43K ohm 14W 1% Resistor, 2.1K ohm 14W 1% MF Resistor, 10K ohm 14W 1% MF Trimpot, 100 ohm Trimpot, 5K ohm Diode

Diode

C. Hex Inverter 0.C. C. Regulator +5V C. Regulator + 15V C. Regulator -15V 1.C. OP. AMP. 1.C. Digitial Analog Con Transistor I. 1. I lL.

Transistor Transistor

8-10 R20, R24 R104 R9, R204 R105, 107, 205 R10, R206 R6, R22, R23, R26, R106 R25 R118, R119, R218, R219 R21 R111, R114, R211, R214 R3 R124-R129, R224-R229 R123, R223 R7, R8& R27 R120, R121, R220, R221 MF R101

R201

R103, R203

R109, R209 R102, R202 Di7, D19, D20 D101-D104, D201-D204 D3, D4, D5, Di2, D13, D15,D16, D18 D105-D115, 205-D215 Ic7 IC8 Ic4 IC6 IC 102, 202 IC 101, 201 Q105, Q106, 205, 0206 Q2, Q7, Q8 Q107, Q207 1N914B

1N4003

7406 7805 7815 7915 TLO81 P/LF351'

2N2102

2N3904 2N3906 Rw BANNER

Page 57

CINEMATRONICS MFGR PART NO. DESCRIPTION REF. DES PART NO

66-10818-01 | TransistorQ6, Q101,2N5210

Q102, Qi03, Q201, 202,203

66-10819-01| TransistorQ108, Q2082N5320
66-10820-01TransistorQ104, Q109,2N5322

204; 9209

66-10821-01TransistorQl, Q32N5550
63-10781-01| Cap Disk .005mf 50VC8, C9
63-10784-01Cap Disk .lmf 50VC24, C27,

C103, C104, C203, C204

63-10786-01| Cap Disk .lmf 100VC102, C202
63-10799-01| Cap Film .33mf 35Vcl
63-10802-01| Cap Polycarb .022mf 200VC101, C201
63-10805-01| Cap Dip Tant .47mf 35VC25
63-10806-01| Cap Dip Tant lmf 35VC12, C13

63-10807-01 | Cap Dip Tant 2.2mf 35V C4, C10, C15, C23, C105 63-10809-01 | Cap Dip Tant 4.7mf 35V C26 63-10790-01 | Cap Elect 47mf 50V C205, C207 36-10620-01 | Socket 16 Pin

35-10613-01| Molex, Male Pin Sold Tail02-09-2134
41-10660-01 | Molex, Receptacle 15 CirJ203-09-1152
41-10661-01| Molex, Wafercon 6 CirJ509-18-5061
41-10662-01 | Molex, Wafercon 6 CirJ309-18-5062
41-10663-01 | Molex, Wafercon 6 CirJ4,J6 K09-18-5069
41-10654-01| Male Header PCB 34 PinJl

80-10902-01 | Printed Circuit Board

01-10506-01_| Neon LampLt1, Lt2NE-2

OANHNHN

NHR NE HH OHNH

51-10722-01 | 10K Pot.Rilatnossr030
20-10523-01Heat Sink Thermalloy22030 B

20-10524-01 | Heat Sink Thermalloy 6045 B Wire mean g&

AUDIO P.C.B. ASSE)

38-11141-01

20-10520-01Heat Sink, Therm“Ref6071B

20-10521-01 | Heat Sink, Therm efer To | 60728

23-10548-01Thermal CompoundDOW 340
25-10556-01| Hex NutAssembly | 4.49
25-10570-01LockwasherDrawinags’’ | #4 Internal
25-10974-01Machine Screw34-40-3/8PNHDPH
41-10652-01Header, 16 Pin609-1622 M
41-10656-01Conn, Molex 9 Cir09-18-5094

ONATAWNH

8-11

Page 58

ITEM CINEMATRONICS NO | PART NO. DESCRIPTION REF. DES. MFGR. Q PART NO. zt TY

V7

4l 44-10669-01 44-10670-01 44-10673-01 44-10674-01 44-10677-01 44-10690-01 44-10691-01 44-10696-01 44-10697-01 44-10713-01 44-10716-01 44-10717-01 44-10718-01 44-10913-01 53-10727-01 53-10734-01 53-10737-01 53-10739-01 53-10743-01 53-10745-01 53-10746-01 53-10747-01 53-10748-01 53-10749-01 53-10750-01 53-10751-01 53-10753-01 53-10754-01 53-10755-01 53-10756-01 53-10759-01 53-10760-01 53-10764-01 53-10765-01 53-10917-01 53-10918-01 53-10922-01 53-10923-01 53-10926-01 53-10928-01 53-10932-01 53-10936-01 §3-11102-01 53-11129-01 53-11130-01 53-11131-01 53-11132-01 53-11133-01 53-11134-01 Ic IC IC IC IC Ic IC Ic Ic Cc IC IC IC IC Resistor, YaW 5' Resistor, %4W 5 Resistor, ¥4W 5: Resistor, 1/4W 5' Resistor, 1/4W 5: Resistor, /4W 5' Resistor, 44aW 5 Resistor, /4W 5% Resistor, Y4W 5% Resistor, YW 5% Resistor, /4W 5% C Resistor, “4W 5% C Resistor, 4W 5% C Resistor, 14W 5% C Resistor, /4W 5% C Resistor, YaW 5% C Resistor, YW 5% C Resistor, /4W 5% C Resistor, %4W 5% C Resistor, %4W 5% C Resistor, 14W 5% C Resistor, %W 5% C Resistor, YaW 5% C Resistor, /4W 5% C Resistor, “aW 5% C Resistor, /4W 5% C Resistor, YW 5% C Resistor, /4W 5% C Resistor, 5W 5% C Resistor, %4W 5% C Resistor, 44W 5% C Resistor, ¥aW 5% C Resistor, “4W 5% C Resistor, /W 5% C Resistor, ’4W 5% C KKK Nz DAAAANAANAANA

8-12 “‘Refer To

Assembly Drawings”’ +: 7406 74\4 7815-C 7915-C 74LS00 74LS163 74LS164 74LS377 74LS393 CA3080E LM555 AMI $2688 TLO81P LM566 150 OHM 1K OHM 2K OHM 2.7K OHM 4.7K OHM 8.2K OHM 10K OHM 12K OHM 15K OHM 20K OHM 22K OHM 24K OHM 30K OHM 39K OHM 43K OHM 47K OHM 82K OHM 330K OHM 1M 1.5M OHM 620 OHM. 2.4K OHM 7.5K OHM 18K OHM 51K OHM 100K OHM. 240K OHM 390K OHM 51 OHM 680 OHM 750 OHM 1.3K OHM 3.6K OHM 16K OHM 150K OHM ws PRE RENN WRHEH EON NEE EEE ONE DBE ONWOPWHENE AEN ANE ENE EEN

Page 59

CINEMATRONICS PART NO. DESCRIPTION REF. DES MFGR. PART NO

53-11135-01 §3-11136-01 53-11137-01 53-11138-01 63-10780-01 63-10781-01 63-10782-01 63-10784-01 63-10796-01 63-10799-01 63-10940-01 63-10941-01 63-10942-01 63-10944-01 63-10946-01 63-10948-01 63-10949-01 63-10951-01 63-10952-01 63-11127-01 63-11128-01 65-10811-01 65-10812-01 66-10816-01 66-10817-01 66-10824-01 66-10825-01 80-11140-01 Resistor, 44W 5% C Resistor, /4W 5% C Resistor, %4W 5% C Resistor, ¥4W 5% C Capacitor, Disk Capacitor, Disk Capacitor, Disk Capacitor, Disk Capacitor, Film Capacitor, Film Capacitor, Disk Capacitor, Elect Rad Capacitor, Elect Rad Capacitor, Elect Rad Capacitor, Film Capacitor, Film Capacitor, Film Capacitor, Film Capacitor, Film Capacitor, Film Capacitor, Film Diode Diode Transistor Transistor Transistor Transistor P.C. Board

8-13 ‘Refer To

Assembly Drawings”’ 220K OHM 430K OHM 750K OHM 910K OHM 470PF 50V .OO5MF 50V .O1MF 50V -1MF 50V .047MF 35V 33MF 35V .OOLMF 50V 2.2MF 35V 3.3MF 35V 100MF 35V .0047MF 100V .1MF 100V .22MF 35V -47MF 100V .68MF 100V 1.0MF 50V 22MF 50V 1N914B 1N4003 Plast 2N3904 2N3906 2N6107 2N6292 REE BONO EEE BONE EN HHO NE WN H

Page 60

APPENDIX A

Assembly Drawings Schematics

and

Wiring Diagrams

Page 61

SP ONAAARWN PE

Bee ee ee NRDABRWNHES TABLE OF CONTENTS

ASSEMBLY DRAWINGS

SCHEMATICS AND WIRING DIAGRAMS

CABINET DRAWING MAIN WIRE HARNESS ASY. TABLE POWER SUPPLY PINOUT ILLUSTRATION CONDOR POWER SUPPLY SCHEMATIC NATIONAL POWER TECHNOLOGY POWER SUPPLY SCHEMATIC PLAYER CONTROL AND COIN MECHANISM WIRING DIAGRAM CPU BOARD SCHEMATIC CPU BOARD MAJOR COMPONENT DRAWING CPU BOARD ILLUSTRATION DISPLAY BOARD SCHEMATIC . DISPLAY BOARD ASSEMBLY DRAWING . MONITOR ASSEMBLY DIAGRAM DISPLAY BOARD CONNECTORS AND ADJUSTMENTS DRAWING . HEAT SINK ILLUSTRATION HEAT SINK ASSEMBLY AUDIO BOARD SCHEMATIC . AUDIO BOARD ASSEMBLY DRAWING

Page 62

UPRIGHT CABINET

32-10889-01

FLOURESCENT LAMP

ASSEMBLY

INTERLOCK

SWITCH SPEAKER Le » ASSEMBLY eruu —— 1, PLAYER ae c 20-10530-0% — CONTROL PANEL ©

aa- 208 -o1\, wontToR AssEWoLy— le ~| a 3e-n207 -o1 [*

a a

SPEAKER

71-10834-01

ry Al COIN BOX TONGUE lI 7

AUDIO BOARD — _

38-Mar-01 A cower —— suPPLY [——

38-10842-Kx

com I] | Losie Boar ed - ~ 01 —— egy 28 nae -o1

20-10896-01 NOTES: UNLESS OTHERWISE SPECIFIED 8 7 6 | 5 * 4 ] 3

Page 63

er ee 3 + 2 | REVISIONS PROPRIETARY eS THIS DOCUMENT I6 THE PROPERTY 1 Sal

OF CINEMATRONICS INC. AND 1S

NOT TO @E REPRODUCED OR

TED WITHOUT WRITTEN D

ATION OF CINEUATRONICS

WIRE LIST WIRE LIST

CONNECTOR |FROM | TO [COLOR] AWS. | PIN [LENGTH] REMARKS ICONNECTOR]FROM [| TO [COLOR AWG. | PIN [LENGTH] REMARKS POWER |HI-7 87 NSTED, [H44 | u7-1 [GREEN | 22 [mace [ >3 [Vow Surety [ura [tame |warte [ia hb PER INCH AUDIO [4-2 lereaKERIGREEN [22 |reMALE| 71 (See Notes moddx [HIEa 1 H4 H4-3 | H7-2_ {REL 2 33 [VOLUME _ 03-03-1042 [ HI-4 NOT USED. MOLEX H2-7_|RED REF. +25 [

POWER |H2-1_|H9-GRN|GREEN 03°09-l058 [us RED | ¢2 SUPPLY [H2-2 | H9-wT WHITE (SPEAMERBLACK | 22 H2 H2-3 [HB-N.O.[RD/aK] 18 sé H2-8 |BLUE REF. -25 morex [2-4 | H3-1 JBROWN | 22. 52 Tereza 2-1 BLACK Rer, GND os-o8- 22 Fas a-7_iWwuITe | 22 WEN -B.3VAC HTS [BLUE | 22 7 33__[ volume H2-6 | W3-14 WELLow | 22 O B2 [spor Kine H2-9__ [ORANGE " REF. 45. Cc (HoT [W3-6 [RED | 18 z $2 [425 Con werer! usa [ha-a [REO MALE_| REF. c H2-7_[H4-4 {RES 2 " 13 425 oenie 5-2 NoT USED. 3S 7 (See NoTE4 Hae 52 |-25 o8-os-tcxe (HSS {HES {BROWN MaLe REF. 2-6 S2 |-25 Losic. LHe NOT USED

[2-4 52 (45 He He-2 NOTUSED 2-4 «| 52 {45 We-3. ae Female | 27 (METER 12-40 [56 45 et ien [HO-4 | He-l2 jek, MALE REF. GND. otk vey, feet REF. GND —

bone H2-11 x watt « [S52 [onp He-5 | H3-12 “| 52 |QND NOT USED

rear «186 16nd

  • FEMALE, IEF, 6.3 VAC. a 3-2 Net USED MOLEX 43-3 NOT USED TORANGE FEMALE REF. 45 03-09-2153 | H3-4 [ NOT USED NOT USED. B H3-5 (|NOT USED HEA NOT USED B

43-6 | h2-7 [RED { {FEMALE REF. +25 VOLUME |_H7-1 | H4-1_ | GREEN [FEMALE REF. H37_| WS [WHITE 2 w REF.6.3 VAC] wold WEE [44-3 [RED MALE TwisTeD

NOT USEO

NOT USED.

i NOTUSED

W3-6 | W26 | BLUE « [RER -25 ososioxs [urs [na8 [BLUE “ H3A_ | NOT USEO ITE RLOCK [HO- COM | H9-BLK (ELK /yeL| 16 FQS W310 NOT USED 48 fWe-¥.0.[ H2-3 /RD/ALK FQD Casa INOT USED Ac | jus=caN [H2=1 MALE’ 96" LONG

LI INE CORD [HI 5 ex3

  • W332 | H6-5, nf 4 FEMae| 47 [GN to? few Ree ALE wine

H343 | H2-4 [ORANGE a Aer. +5 314 | H2-6 [YELLOW a REF Sor KL, W515 | W211 [BLACK 7 REF GND WaTERIAL Oar [SE wens pasaeCT Enea? [oare! CINEMATRONICS EISsmme ne

4, TERMINATE SPEAKER END WITH .187 FQD NOTES: UNLESS OTHERWISE SPECIFIED

WG TITLE FQ - AELEASE Bron DATE 3B FQD- FEMALE QUICK DISCONNECT REE OTT AAIN HARNESS ASST. A

  • W/N ~ THIS CONNECTION MADE WITH WIRE NUT TINISH 100 NOT SCALE Owi 1, LENGTHS GIVEN FOR TWISTED WIRE ARE AFTER TWISTING, OtMERWISe Seteiién [wooEL NO.

FROWeCHOR SAE £3 -@)xo 2 [Rene wamr 4 3 4 2 1

rare

Page 64

Tron or Bees <

PROPRIETARY

THIS DOCUMENT IS THE PROPERTY

(OF CINEMATRONICS INC. AND IS

DISTRIBUTED WITHOUT WRITTEN

AUTHORIZATION OF CINEMATRONICS.

we,

NOTES; UNLESS OTHERWISE SPECIFIED

U! COMMIECTOR QATA PINA|WIRE COLD | FUNCTION Viel \GRA/YEL | CHASSIS GUO. vez | war |TKFMe LuG#3s IN |viee | 6K [TKEMR LUG) via | G@en/vec | 6.3VAC GNO ws | one | 6.5uC wie [sen | SPOT Kit ZOU) Yen_| +e5v. BLU 725V. RED +oV GRY +o,

dq LX SAME MILE FUSE. BX SAMP WLME FUSE. BM GAMP ILUNE CIRCUIT BREAKER CB |. A) SAMP IWLINE CIRCUIT BREAKER CBE.

REVISIONS

VE COMMECTOR DATA "PUIMB|WIRE COLOR] FUUCTION. Wel | BRN | TKEME Lug al J&e | oeg TEM WGes. ve-3| REO [TKEMe weee ee

ve-¢ | EL TXEMR LUGHE POWER SUPPLY CONECTORS BOTH JE AS VIEWED -ROM THE B

FROLIT OF POWER SUPPLY. Caron ote ciwematronics GiNe

BREAK ALL SHARP. EDGES AN DEBURR aCe HOLES,

Page 65

SEE NOTE ON

POWER SUPPLY

CHASSIS FOR

CORRECT FUSE

ANO VOLTAGE.

SELECTION:

CHASSIS / EARTH

GROUND

). SCHEMATIC SET FOR 115. VAC OPERATION

NoTes: UNLESS OTHERWISE SPECIFIED TH T1 Ria 470.0. Yaw RT BION. pw TEES SPOT KL

470.2 Yew Rio’ INS401 CRB.

CRT INS401 cet

cRe INS401 INS4O1

RY 470.0/2W RB cba 6.3 VAC

Whew

Pe be RID

exo 78 ay Rr eseut ie BO

+5— CRO | ag ebob| 1.6K, ME 1%’ +. Leooog _ ce

ea FN IBY MReo08. °7 N. Ris 4003 SOL, eRe Qi 2N60S5 =

au 22k Yew 22m 7 ev Re won iN4003/ CR? SYSTEM COMMON Gea Gl CONDOR POWER SUP, 72-10B42-22 [—eenTat

8 7

Page 66

4 1 vr REVISIONS PROPRIETARY ey Se one [ammo

cure oobesent Te onopRaTY N

>|

oO

TECHNOLOGY INCORPORATED, J2 waren Drama [DE oo ereRerasl CINEMATRONICS [Noma

Paovecr ewan: [OATE RELEASE avvaov] pave] WS TLE NATIONAL, POWER TECHNGLOG? [A FINISH: DO NOT SCALE Dw] POWER SUPPLY

Fouena F [SPRERWIGE GEES e> JwOOEL NO] pw [owe REY, NOTES: UNLESS OTHEAWISE SPECIFIED SOE TRS og [2 10842-4a] A = ~O- [coe 1ERT SHEET? OF 7

4 3 * 2 i 1

me ee

Page 67

L

PROPRIETARY

This DOCUMENT IS THE PROPERTY

OF CINEMaTROMICS INC. aNO IS NOT 70 8£ REPRODUCED OR DrgrmIBUTED WitHoUT WRITTEN D | sutwonzstion oF cmenatromics ine. r

INTERCONNECT

Pc.B. Po Rt ¢EVISIONS, Rev] DESCRIPTION DATE | APrROVD

PLAYER CONTROL PANEL — REAR VIEW

TV WHITE/GRE O- /GREEN.

At 10 | P41 ! BROWN

Pa 1 RED

oS < a PS \ ORANGE PLAYER T\WO

P4 i YELLOW

PS | GREEN

1B a PS 12 279 i 19 <—__— 5 17 el PIO A PH 16 <—___—"__o Pi2

7 PLAYER ONE

FORWARD RIGHT

| FIRE i LEFT FORWARD | RIGH iT LEFT

i BLUE 2 pis LvioceT | pig}

GRAY

4 6 PIS 4 WHITE

1 €d ‘Ng'D OL S1IBVD NoOgaly oa oO adunvatn-ag ha) O- NORMALY OPEN 5 2 NORMALY CLOSED 4

t AC)

eo NOTES. UNLESS OTHERWISE SPECIFIED RIGHT N.C. N.O. COM

AWAD YMoDVv1S WATERIAL mene rae one Le THmE: COIN SWITCHES MOUNTED ON COIN DOOR REAR VIEW PLAYER CONTROL, COIN MECHANISM A BYRING DIAGRAM

FFOLERANCE UNLESS co 12-11209-02 ATTACK Lesa site, Wwoor ways owe we aa PROJECTION: [SCALE: x : A

+ +O [cO0E JOENT. Lo mttot

Page 68

i i ie v ae Pa |__

a eo < i) nod, vos ne oa Hove ils 2152

Hi 3 ~ Tan eHO #2 FT yOS7 EP seal

Page 69

(503) 4972 _ a SELECT 5 (307, a7, 60) KIO KKB T2 s9P2 (305 ,3A6,403) 7 KG KS KA rae ¢ (183 ,3C3, 345,403) KB K2 KI KO

4 fr mz.

i Re Select

i 74LS257 a (STROBE aore Nee eet f wer 7ALS287

UO A & te O HO (PAB ten — (26? z ROBE A a B 8 GS Ze SK gee gO |S Beg gras ge gO LR, ba palenTnclinslena 1 Teeclenslrazlon pao NN

—(28ey) LB) ap 1 +2524 DIAGNOSTIC. TEST DINE. Tie Low FOR TEST

twos SRE (ste

i

rN A7-2 (2.5640) ABER i vaee PRE Be fi 78 oy

Ic is “ie fis (203,686, FA pe Snes ia x

oc22 2

f oe IB reer izle Ds fle 13, | [GC Gc OES. {G0 CC Ce al es esre cay 8 2c TA core ee Rs

1S. i sarsse et ly) csi [AME ley tesa wars ft one FS i # QD GC ME OA

Leow core 3, L anar_ 1D), E SLIN core Seg MG usa | awa Gey LS I94 Zour 1g, {Qc DCB se Cees re 5 UU 4 Fae ei & ‘67 Ire [es Tee ‘re re ie (303) 1303 IS TIRE 1a, & HEMORY CPU, SCHEMATIC. DiaseaM WITH SIGNATURES

NOTES: UNLESS OTHERWISE SPECIFIED

a 7 T G 5 z

Page 70

A7-3

NOTES: UNLESS OTHERWISE SPECIFIED

We 2 cc) .s0" L4 ras ce. wx ca 946,

(EAI Bea 7 vi { Cie, zB ye MUE ry bial

= balla X,ARITH,

ca r

oly spicec go pe @ ‘ Me —s

NE 2ELSIBL ‘ae

Le Ta we ) (4A5) t PSO PGI (see) “(a2 Ch F8A_ oy oe _enere co 1586)

Page 71

ace [SIGNATURES W BOX jx} FOR No JM) OPTION. ROMS rod ote 3 a<ak Deou Soha ioe A Otc REIN, Be SE on ia Sesto Fee

Page 72

A7-5

Page 73

ae 1 aS] a oe

[onc toap TALS FB

al 3 creas onnmecenres 28 & 2B 8 7 7

Page 74

Prormierany CONNECTOR JS

CONNECTOR J4 CONNECTOR JZ

FROM / TO Je PIN NO. SchMTE, locaTion SHT-AREA PIN No. FUNCTION, Ram /70 IC~ PIN NO. scum, LaeaTion SAT-AREA Pi NO. FUNCTION FRoM /7 IC-PIN NO. SeuMTe L0cATION SHT-AREA PIN No. CONNECTOR J4 SoHM TC, LocaTion SHT-ARER,

From /7 FUNCTION Geom

é ° ve Vu cl iz NC NC Com UNTER

  • (emt) GND GND 6ND. NC. NC LEO CATHODE +5 FROM COLLECTOR o Qi FROM AZ-36 I-c4 6-03 -aneaghsn W

NC YOAC, yOAC, OAc iT f BIT gD airs aire BIT 5. até ait 7 BIT YOAC BIT 9 Yoac aT 6 YOAC BIT 1g YDac yoac. yoac Yoac, Yoac 12___ INTENSITY FROM M2-S FROM 2-19 FROM M22 FROM M2~6 FROM P2-9 FROM 2-19 FROM P22 FROM P2-6 FROM S25 FROM S219 FROM S2-6 PROM Je-3 Yoae ert 17 FROM S2-2

1s Bt et BRIGHT GND XOAC OUTPUT ND FROM J2-1} FROM DISFLAY PCB To CONN. J4- 4. INITIALIZE SWITCH FROM HE-13

DRAW SWITCH GND DAC BITD Guo OAC. BIT | end

CONNECTOR LOCATION CN CPU. BOARD WITH PIN NO. 1 CALLED GUT ze KOAc XDAC XDA DAC XDA KOAC are BITS airs FRoM T6-2 FROM Me-ie FROM ME=12, FROM M215 FROM M2-5 FROM P2-I6

airs BIT BIT 7 FROM P2712 FROM PRIS PROM P2-5

NOTES: UNLESS OTHERWISE SPECIFIED a) 3+ DAC XDAC KOAG XDAC ars air ar ig BIT i FROM SR-16 FROM S2-12 FROM 52-15 FROM S2-5 GAs 6-Ae 6-03 ene ees e-ce o-e8 o-ad Ss e cy " NC +s SECONDARY INPUT SECONDARY INPUT 3 SECONDARY INPUT 2 SECONDARY INPUT fF SECONDARY INPUT PRIMARY INPUT 3. PRIMARY INPUT / PRIMARY INPUT B

a rey le i ar les Re TOe4-4 To E4-1 To £4-2 To £4-3 70 64-13 To D4 -1 PRIMARY INPUT 2 TO 4-2, To 04-3 To ot-# PRMARY INPUT 7 10 O4-le

PRIMARY INPUT © PRIMARY INPUT 5. PRIMARY INPUT 4 PRIMARY INPUT I PRIMARY INPUT ig. INPUT 9 INPUT & INPUT 12 PRIMARY PRIMARY PRIMARY PRIMARY INPUT (3 PRIMARY INPUT Id PRIMARY INPUT IS COIN SWITCH (WORMALY CLOSED) COIN SWITCH (NORMALY OPEN) GND TO Dan 12 To 04-14 To 4-15 To C41 To 08k 7064-3 Tong Toca IS CONN. J4-3 To c4-14 CONN, J4-1 Ta 04-13 CONN 4-5 To 04-12, CONN, J4-2 To A4-5 To Agi 1-86 Ae I-05 Oo orang u ra * 1s PRIMARY INPUT 13 TO C4-/4 CONN. J3-21 To ceria CORN. u3-23 TO 04-15 CONN. J3-20 FROM DISPLAY PCB CONN, Je-16

  • C413 CONN. J3-22 (Ae

PRIMARY INPUT IS PRIMARY INPUT 12. XDAC OUTPUT PRIMARY INPUT (AG

we Ne ond ne EXTERNAL HIGH OUTPUT ouTeUT UT PUT / ouTeuT 2 OUTPUT 3) OUTPUT 4 OurpuT 7 To Ae-8 S-A7

Be-s FROM Fe-4 FROM Fe-5 FROM F2-6 FROM F2-7 FROM Fe-9 FROM Fe-12, ea cneharzouics RO TRE feo MEMORY] 16 K MEMORY CPU, SCHEMATIC [ia fre-142 02] 4) rarcid Taare 4 | 3 I 2 1

Page 75

accum. secect @)

CONN J3

INN @ i a

*TO 20 MHz ourTPUT AUDIO COIN

COIN CONTROL COUNTER RESISTOR

SELECT | BRIGHTNESS 4 Ve | D c

2 2 BACKS 5

GAME OPTION SWITCHES

FROM

INPUT SELECT @ CONTROL

PANEL

G c 4 4 o2

PRIMARY ACCUM. (2) DISPLAY . “PROCEEO”

ReGisteR 10 DAC 80's LINE LENGTH COUNTER (3)

ABWEE TO LF1I3331

ADDRESS, SELECT (4) DATA SELECT G) RAM ADDR. SEL, & AEG. gh AGe SELECT

moreso @ J INSTRUCTION ‘ADDRESS 13 REGISTER REGISTER RAM STORAGE © =— (cy SYSTEM vu t seauence @

14 13 RAM DATA REGISTER () "OR 16-LEVEL INTENSITY CIRCUITRY

Page 76

PROPRIETARY

THIS DOCUWENT IS THE PROPERTY

OF CINEMATRONICS INC. AND IS

MOT TO BE REPRODUCED OR

DISTRIGUTED WITHOUT WRITTER

D) aitmoniznrion oF cweuarromes

Ine,

NOTES: UNLESS OTHERWISE SPECIFIED

ee ae 3 x 7 REVISIONS

  • CABLE

7 osparne ! Toa R08 SAPs ONBLE | \ 70 gure PALEL, vA 26 PM CABLE:

ve v4 v3 70 POWER HARNESS (POARIZED) [-— oF 824708 OFTION swrrew

LOGIE PCR

Page 77

8 7 6 | 5 3 GouLectoR I ral a

@ios, geo4 ow 100. vr v

WHEN BECKMAN 7SG0VS DAC |S UTILIZED FOE F210 AND Ie EON

BIOL CHANGED TO WOK ith META Fleth R201 CHANGED TO 7-5 My METAS FILM, fxm) GeckMaN DAC NOT COMPATABLE WIT BURR GROWN OAC. ‘ R109

VERTICLE,

PICTURE SIZE.

VERTICAL,

OEFLECTION COL

paceo \ (02 7 uo YO

iNDI4B 4 PLCS. S00 I =

SCAUTION=

DO NOT APPLY POWER TO DISPLAY ELECTRONICS DAMAGE TO DRIVE ELECTRONICS

UNLESS POWER TRANSISTORS ARE. CONNECTED. FAILURE TO -00 SO WILL RESLT IN PERMANENT DAMAGE TO DRIVE ELECTRONICS.

leit

cl cee} ows LE, Laat 7 ALL SCOE WAVEFOR: O32 ~

Wee wit Game /2Nsa7e

Braanogric. Mnoe AND. Wenn Soke “OF & ALL RIDES ARE WEEDS, 8, GCL CAPS ARE IN uF, 59V, DISC. SEE_CAUTIO: ALL RESISTOR ARE IN OHMS, /4w, CARBON SEE nN

A} A\SOLOER POINTS ON P.C. BOARD

ZX POWER TRANSISTORS ARE MOUNTED ON HEATSINKS & ARE

SEPARATE FROM RC, BOARD, (OWG# SDI002I4). A\RI24--R129 & R224—R229 ARE COMPOSED OF 6 EACH ma

2.7.4, |W, RESISTORS IN PARALLEL. Noes, UNLESS OTHeRMISE SPECIFIED a | 7 / 6 I 5 + 4 3 ; pv Tm DISPLAY_ELECTRONICS: KELTRON

Page 78

Pacemieraay SUPPLY CONN.

KELTRON

Tor Totes a¢203 Kow posaz4q fica]! a[ sv lev TANT

¥ Al0-2 | reves VT a ye7,PIN 4 _ AULA 3, Ty ‘gh maale He e0l24a

= 0)

NOTE: USE 5K RES.

BETWEEN D4(CATH)

AND Rit WITH

AMPEREX CRT ONLY. SAT HO] a DISPLAY RC.B.

ck I.

BRIGHTNESS 64 FOCUS “ Kd RT SOCKET (D To ert ccatHoos) 380 tant 480 rawr

Lf=3" | 2 | 1

Page 79

All eae Pa

<0“) PS cane 4. af los BO pa ai)

  • “Denlll rast ae i HE GoE oe ayaa yalslals wiccccece

eae ntewe Mt. ZERO OW, CEH) Amant tunel $00 V8 OR Ue FoR 1 1 Me coue ts SES ns ad Scena tH Conoerass er Satan Hie wane mae, (fe aa Bec one)

Page 80

YOKE ASSEMBLY GROUNDING SPRING 38-10637-01

25-10583-01 fa | CB

HEATSINK 20-10522-01 . ™*, a & CRT. SOCKET ASSEMBLY 38-10632-01 19" CRI. 90-10860-01 KELTRON HIGH VOLTAGE POWER SUPPLY 82-10841-01 OR PTK HIGH VOLTAGE POWER SUPPLY DISPLAY P.C.B. ASSEMBLY ( 82-11083 -01 38-10628-01 =" MAIN HARNESS ASSEMBLY 34 PIN 87-10877 -O1

RIBBON CONNECTOR 87-10848-01 MONITOR ASSEMBLY (PTK) 38-11207-01 MONITOR ASSEMBLY (KELTRON) 38-10633-01

Page 81

SLNAWLSAPAGV GNV SYOLOANNOOD @Od AV 1dSId SSANUYVH

isnrav NIVW

ssaniHoua =f en Q Co a YOLOSNNOO Nid ve yalandwy

er (° \wowoar430 TWLNOZIYOH (AVLNOZIYOH) HLONST 3NIT,X, O| tazis <

se Q@| Winoziw0H) BOWE TOA NIVS Xu C4 HOIH (F101LY3A) HLONAT ANiT,A, |S 3xOA

(3ZIS FIOLYSA) NIVD A, [2] oe q wonsasa

ATOILYSA

Page 82

a, Al4 PROPRIETARY ‘TMS DOCUMENT IS THE PROPERTY OF CIMEMATRONICS INC. AND IS MoT TO BE REPRODUCED OR DISTRIBUTED WITHOUT WRITTEN ‘AUTHORIZATION OF CINEMATROWICS.

ine, qo —_I (VERTICAL) J4 , REF. GO20220)- MOLEX COMIN.~ FN, 09-09-1063 (/EA,) MOLEX MALE PIM - Pil. 02-09-2118 CEA). MOLEX FEMALE SOCKET- Pk). 08-09-1118 CEA). THERMALLOY TRALMS. SOCKET PU 8/3-PF-603 (GEA). REVISIONS

rev] ‘DESCRIPTION ‘ATE _| APPROVED. B)PERECR OSB sae Ot

p>——_ 12.00 88. ~ L

GRAY OF BLUE

Fe BLacK

eS GAEEN

fq FED

Fa WHITE OB WHT/YEL.

Fe OFANGE

Me © eNSB76

(HORIZON TAL) /-

13, REF. rN HEAT SISK HARNESS, 2/78 J \\errau, 2use78 Cc

2007-A

00 238: = . eae 2 WHITE OR WAT/YEL.

MSs ORANGE © i=

ih

f¢ Gety OF BLUE

Fs BUCK,

Fe

  • | _cxeen \ 2NES7E \

LJ \ HEAT SINK HARNESS, 2178 MOLEX COWL) -F1/,08-09- 103 (/EA). MOLEX MALE PIS: PAL. 02-09 -2//8 (EA). MOLEX FEMALE SOCKET- PKI. 02-09-1118 (5EA,).

NOTES: UNLESS OTHERWISE SPECIFIED ‘BREAK ALL SHARP. EDGES AND DeBURR ALL HOLES. Net SIIK 207A OWG TITLE = SCHEMATIC, VERTKALE HORIZONTAL HEAT SINK ASSY.

Page 83

a a =

g@vl 40 dOl GNV YOLSISNVYL dO 30VSYNS WOLLOG SYILNA OL GNNOdWOS WWYSHL AiddV GNNOdWOD TIWWYSHL avi YOLSISNVYL 40 dOL NO G4a90V1d SI MNIS LV3SH TIVWS

Al5

Page 84

8 7

< SaTTRat PRopaierany

TANK EN-+

BEEP EN+

CHOPPER Sw+

Hit TANK FIRE-

+15V ." on T i _ zt RoW --LB» a8

  • CAPACITOR VALUES AGEN af
  • RESISTORS ARE Y4 WATT Sie CARBON

1. RESISTOR VALUES ARE IN OHMS

NOTES: UNLESS OTHERWISE SPECIFIED

Te NO. an ‘:257,9, 10,1327, TYPICAL +S CA30BO 2K con 0.0477, 4 1 1 , i C58,C57 a 7

cea c47; €56,c58 ats Tar oe Bay LS 393 2k Ra Ris, +15 eK 20K tte

e fi

x

AND Ys RO uf eee ARMOR ATIACK ALDI

rs NOT SCALE, [SRuERaSE SOeEzo laa ol er}

38 | 7 oo | te- 1141-02 | A

sr = £ 2 1

Page 85

Al16-2 anno mame -p| SHEET ONE o—v— AREA A-4 R101 4 3 t 2

PROPRIETARY

‘THIS DOCUMENT IS THE PROPERTY

OF CINEMATRONICS INC. AMD (S

BE REPRODUCED OR

UTED WITHOUT WRITTEN.

(ZATION OF CINEMATRONICS FROM

SHEET ONE

AREA A-4 R99 24K 2N35904 Q15

{lh

Qe 2N3906 Ride RIO 39K ° aK +SA 15

R10S 4.7K

SHEET ONE On AREA A-2 R106 ark NOTES: UNLESS OTHERWISE SPECIFIED et [DO NOT SCALE Dw REVISIONS ‘DESCRIPTION DATE ‘APPROVED

| 18 TO SHEET ONE AREA A-4 G) TO SHEET ONE AREA A-4

  • TO SHEET ONE AREA A-3 SAPRIL 1981 CINEMATRONICS fils

4 3 s 2 ce ‘S020 REMOR ATTACK AUDIO Elcapon

Page 86

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 87

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.