Tetris TM-328 2nd Printing Kit
Tetris (set 1) (Atari Games, 1988) · Kit Manual · 20 pages · 34 sections · original scan
Se ae: saison
Kit Installation Instructions
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
AM
ATARI
GAMES
WETAMS
Kit Installation Instructions
Ns Ne we Bek. *
and © 1987, AcademySof-Florg, All rights reserved. Tetes licensed to Andromeda Soft ware Ud; and sublicensed to MIRRORSOFT LTD and Sphere, Inc. © 1988 Atari Games Corp. All rights reserved, Original concept, design, and program by Alexey Pazhitnov and Vadim Gerasimov, respectively.
Copyright © 1989 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, and this technical manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035
Printed in the U.S.A 3r
Produced by the Atari Games Technical Publications Dept. Editing and Design: Andrea Dencker Illustration; Mary Ohanessian Sumner Tetris/Upright
Notice Regarding Non-Atari® Parts
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:
- Substitute non-Atari parts in the game.
- Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
- All ground wires in the game are properly connected as shown in the game wiring diagram. ¢ The power cord is properly plugged into a grounded three-wire outlet. ¢ On games provided with an Electromagnetic Interference (EMI) ground cage, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Tetris/Upright
Table of Contents
Installation How to Use This Manual 1 JAMMA Cabinet Requirements -1 Power Supply Requirements -1 Video Display Requirements Installation Precautions .... Tools Required... Preparing the Existing Game for Conversiot Inspecting the Kit .. Installing the Kit Parts Testing After Power-Up Adjusting the Video Display. Setting the Coin and Game Option: Game Play.... Tetris Game Statistics.
Self-Test
Statistics Screen Coin Options Game Options . EEROM Reset Options Video Display Tests Audio Test... 3 Troubleshooting Video “Noise” Interference .... Video Display Sync Problems Horizontal Shifting. In Case of Difficulty. Warranty
iii
Tetris/Upright
Safety Summary
The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.
How to Use This Manual
This manual is written for those who have knowledge of electricity and technicai expertise in video games, such as game operators and service personnel. It provides information for installing, testing, and troubleshooting the Tetris™ kit for upright games. (Another version of this kit is available for cocktail-table games.) The manual is divided into the following chapters:
- Chapter 1 describes the installation procedure and the Tetris game play.
- Chapter 2 contains self-test procedures.
- Chapter 3 contains troubleshooting procedures. Chapter 1 provides the information required to install the Tetris kit. Carefully read the information in this chapter before attempting to convert any game.
JAMMA Cabinet
Video Display Requirements
This section describes the requirements for installing the Tetris kit into a Japan Amusement Machinery Manufacturers’ Association ((AMMA)-compatible cabinet: © Speaker: 8 ohms 10 watts
- On/Off Switch: 6 amp (or greater) 120 VAC
- Coin Door: Dual coin acceptors
- Coin Meter: +5 VDC or +12 VDC © Power Cord: Three-conductor with ground
Installation
Power Supply Requirements
General requirements:
- +5 VDC + 0.25V @ 2.0 amps «© +12 VDC + 0.5V @ 1.0 amp
© Color RGB monitor
- Video input 1V to 3V peak-to-peak positive polarity
- Sync TTL positive polarity separate horizontal and vertical, or negative polarity composite sync
- Horizontal frequency 15.750 KHz
- Vertical frequency 60 Hz © Horizontal mounting
- Recommended size: 19 inch
Installation Precautions During installation:
- Be sure to unplug power while working on the ser~ vice cabinet.
- Be sure all connections and harness routing are secure.
- Make sure all grounding connections are secure and properly affixed.
1-1
Installation
Tools Required © Drill with 3/32 inch, 1/4 inch, and 7/16 inch drill bits
- 1/4 inch plex bit 1/4 inch plex hole saw
- Hole cutter 1-3/16 inch ¢ Phillips screwdriver © Flat blade screwdriver
- Small flat blade screwdriver
- Socket set
- Wire cutters and strippers
- Straight edge
- Putty knife
- Sandpaper ¢ Paint
- Squeegee ¢ X-ACTO™ knife
- Wood patch + Fast-ons (if installing a new JAMMA harness)
Preparing the Existing Game for Conversion
- Turn off power to the game.
- Remove the old PCB and game harness Cif not JAMMA),
- Remove all control panel decals, labels, and controls.
- Remove any side decals from the cabinet. If your cabinet has woodgrain sides, remove the old gtaphics and adhesive (you can remove adhesive with lacquer thinner).
- Remove the video display plexiglass, display bezel, attraction shield, and marquee, if any.
- Paint the cabinet, if required.
- Wipe down and vacuum the cabinet as necessary.
Inspecting the Kit Verify each component with the kit parts list provided in Table 1-1. If any part is missing or damaged, please contact your distributor and provide the following information: 1, Tetris kit serial number
- Part number and description of any missing or damaged parts
- Date received
1-2 Tetris/Upright
A046905-01
©136066-1100. “© 13606-1101 -£137329-450. 137412-101"* 137430-001 ~ 137535-006 137550-001 137577-001- A046501-0: . 046502-01 046511-01-
046506-01 046507-01 046308-01 038158-01 039450-01 TM-328.- © 171089-101 178237-001 178237-005 160044-001 Cover, Control Par Decal, Side Panel (2)
178000-002 102020-001 178265-001 72-6612
75-5116B 177010-240 178114-032
‘Note; All parts are a quantity of 1 noted in parentheses,
Installing the Kit Parts Display Bezel
- Find the display bezel (part no. 046502-01). Measure the size of the existing display bezel or the required size to fit and cut the cardboard display bezel to size. (See Figure 1-1.)
- Place the bezel labels (part nos. 046511-01 and 046511-02) in the lower left and lower tight corners, respectively, of the display bezel. (See Figure 1-1.) Product ID and FCC Label
- Place the Tetris product ID (part no. 038158-01) and FCC label (part no. 039450-01) on the back of the cabinet.
‘Tetris/Upright
FCC and Product ID Labels
u
Side Panel Decal (1 of 2) Installation
Attraction Shield
Attraction Film
Video Display
ip) Display Plexiglass from Previous Game “Build Solid Lines” Label
Figure 1-1 Installing the Tetris Kit
Side Decals
- Find the side panel decals (part no. 046508-01). Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decais as desired. Remove any wrinkles in the artwork using a Squeegee.
Attraction Shield
- Find the attraction shield (part no. 046504-01) and the attraction film (part no. 046503-01). Measure the size of the existing shield or required size to fit and trim both parts to size. Install them on the cabinet as shown in Figure 1-1.
Control Panel
- Unpack the control panel cover (part no, 046507- 01 and control panel decal (part no. 046505-01). Measure the size required and cut the control panel decal and cover to fit the existing control panel. . Determine the location of the player pushbuttons and joysticks on the contro! panel. (See Figure 1-2.) pp
- Mount the control panel
. Install the red player
. Install the blue player
- Cut holes in the control panel and cover to locate the buttons, joysticks, and mounting screws. Note: You can use the new cover to protect unused holes in the control panel. . Install the control panel decal onto the control panel. Cut the appropriate holes in the decal. . Install the button labels on the control pane! decal. (See Figure 1-2.) . Install the instruction label (part no. 046506-01) on the control panel decal. (See Figure 1-2.)
cover on the control panel using the bolts and nuts provided.
control buttons (part no. 178237-001) for the left player. (See Figure 1-2.)
control buttons (part no. 178237-005) for the right player. (See Figure 1-2.)
Installation
Control Panel Cover
Red Buttons
Blue Buttons
Figure 1-2 Converting the Control Panel
Joysticks
- Unpack the joysticks (part no. 171089-101). Perform. final assembly of the joysticks using the documentation included with them. Use the long joystick handle if you have a wooden control panel and the short joystick handle if you have a metal control panel.
- Mount the joystick assembly base on the control panel by securing it with the following parts:
- 10-24 x 1 inch carriage bolt (part no. 75-5116B) © 10-24 poly locknut (part no. 177010-240) Since the Tetris game uses just the left, right, and down positions, your joysticks may be shipped with three microswitches each, not four. If your joysticks have only three microswitches mounted, make sure the side without the microswitch is closest to the player after the joystick is installed.
General Harness Installation. Skip to Grounding the Cabinet if your cabinet is alteady equipped with a JAMMA harness. 1, Find the JAMMA harness (part no. A046501-01) and install it.
- Refer to Table 1-2, JAMMA Pin Assignments, for wiring information.
- Connect the JAMMA harness to existing component harnessing. You can do this using crimp splices or by butt soldering. (The following describes the butt soldering technique.)
Tetris/Upright Installation
“ minal’on* ‘the ‘power supply. One wire® Should g
positive'sense terminal on the power’supply,
or 12V counter. Note: Do not use 24V counters. ® These five’ 3-1). counter(s). The positive: side of the coin counter(s should go‘ to the +5V or +12V terminal ‘of the’ power * “<supply, depending on whether the coin counter is a Ea -
ires attach 10 the video © display” Gee Table
ed A fae test switch is located at 50) on the PCB, If
Installation
4, Try using the existing connectors. Cut the original wire approximately 3 inches from the original connector, Strip off about one-half inch of the insulation.
- Slip the shrink tubing over the wire you just stripped.
- Solder the new wire designated for that position to the original wire you just stripped.
- Slide shrink tubing down over the soldered wire. Melt shrink tubing around all uninsulated in-line wire connections. Do not use electrical tape. It can unravel and cause problems with the electrical system.
- Use wire tie wraps and secure the cable to the cabinet where it seems necessaty.
Connecting Power Wires
- Connect the wires that are designated for your power supply. You will need a supply of +5V and +12V. The new game may not require all of the voltages used in the original game. Tie off any unused wires.
- You will notice that there is more than one wire for each voltage. You must double up some wires as called out in the footnotes of Table 1-2, This will help to ensure that you do not overload the edge comnector and cause it to burn.
Connecting Video Display Wires Connect the wires designated for the RED, GREEN, and BLUE video guns along with the sync and ground wires.
Connecting Speaker Wires Find the two wires (twisted pair) that are designated for the speaker and hook them up.
Connecting Coin Door Wires
- Connect the designated wires to the coin switches and meter.
- Connect the door lamps to the appropriate voltage on the power supply. Some games have separate power supply outputs for the coin door lamps.
- Be sure to clean and lubricate the old coin mechanisms.
Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this Jead in daisy-chain fashion to the coin door, control panel, video display, and power supply. This is a safety requirement for the players’ protection. This AC ground must be of #18 AWG wire or larger.
Cabinet System Checkout Do the following before plugging in the Game PCB:
- Apply power to the game, and check for the following voltages. If any voltage is incorrect, remove power and correct the problem before proceeding any further. ¢ +5 volts on pins 3, 4, C, and D of the 56-pin PCB connector
- +12 volts on pins F and 6 of the 56-pin PCB connector
- Check that the display has power by observing the glow of the filament inside the neck of the picture tube.
- Check that the attraction shield lamp has power. 4, Check that the system ON/OFF switch functions properly, Now turn off the power to the game.
Tetris Printed-Circuit Board Installation
- Find the Tetris Game PCB (part no. A044809-01) and install it inside the cabinet. Use the nylon standoffs to secure the PCB through its mounting feet.
- Connect the 56-pin connector to the PCB with the label on the same side as the components on the PCB. The connector is keyed for proper orientation. Table 1-2 shows the JAMMA pin assignments. 3, Apply power to the game. Check that the Game PCB functions. If a video picture is not present, refer to Chapter 3, Troublesbooiing, for suggestions on what to do,
Tettis/Upright
Testing After Power- The Tetris kit tests itself and provides visual and audible indications of the condition of the game circuitry and controls. Self-test information is displayed on the screen and through the sound system. No additional equipment is required. We suggest that you perform a self-test when you first set up the game, each time you collect the money, or when you suspect game failure. The self-test screens provide information about the game circuits and controls. Refer to Chapter 2 for information on all of the available self tests.
Adjusting the Video Display
You can make the following adjustments to the video display: ¢ Adjust horizontal and vertical hold until picture does not flip or tear
- Adjust horizontal and vertical centering until picture is centered on the screen ¢ Adjust horizontal and vertical size until all four corners are just visible on the screen ¢ Adjust brightness so that all color bars are visible but the background is not
Setting the Coin and Game
Options
The Tetris coin and game options are set during the Self-Test. Chapter 2 describes the recommended settings and the procedure for setting the options.
Game Play
Installation
ing difficulties. Bonus points are awarded for starting at higher levels. New game challenges are also added. At the medium starting difficulty, there is a “handicap” feature which adds stacked pieces at the start of the game. At the highest starting difficulty, randomly generated blocks appear during the game, adding a touch of the unknown. To complete a round, players must meet the given quota of lines for that round. The quota increases with each round, and the number of rounds is unlimited. For double scoring, players can pull down on the joystick to increase the speed of the falling piece. If a one-player game is started, a second player can join in at any time. A game continuation option is also included. Game play is broken up into groups of three rounds each with a different line quota necessary to complete that round. First group of rounds (easy difficulty): Players play standard Tetris. Second group of rounds (medium difficulty): Each round starts with a pattern already in the playing area. Third group of rounds (hard difficulty): A single block is randomly added to the existing puzzle every 8, 5, or 3 pieces dropped. Fourth group of rounds: The program moves all of the pieces up one line and adds an incomplete line of blocks at the bottom of the playing area every 8, 5, or 3 pieces dropped. Fifth group of rounds: Is similar to the second group, except that the starting patterns are different. Sixth group of rounds: Also starts with patterns. These patterns are made up of the initials of the 1st, 2nd, and 3rd high-score entries. Seventh group of rounds: Is a
Tetris is a one-player or simultaneous two-player game of skill which can best be described as a “puzzle in motion”. The player uses a joystick and a button to move and rotate descending geometric blocks. The object is to fit block pieces together to build horizontal rows as solid as possible. With the completion of a row, the entire line disappears and any pieces above combination of groups 2 and 3; that is, they have the same starting patterns as group 2 and the program randomly adds a single block. Eighth group of rounds: Is a combination of groups 2 and 4; that is, they have the same starting patterns as group 2, and the software randomly adds lines to the bottom of the playing area. Ninth group of rounds: Is a it drop one row. The intensity increases as the pieces are stacked higher and higher. If the pieces are stacked to the top of the screen, the game ends. At the start of each game, the play- Avoid Leaving Holes combination of groups 3 and 4. The software adds both a random single block and a line at the bottom. The game then wraps back to use groups 6, 7, 8, and 9.
er(s) can select one of three start-
The Tetris™ kit performs a series of self-tests that provide visual and audible indications of the condition of the game. Self-test information is displayed on the screen and through the sound system. No additional equipment is required. To start the self-test, turn on the self-test switch located at 50J on the Tetris Game PCB. (The power to the game can be turned on before or afterwards.) To end the self-test and return to the Attract mode, turn off the self-test switch.
RAM Test
The first test performed is the RAM test. It tests the processor RAM and color RAM. The test takes about three seconds. If there is no problem with the RAM, self-test automatically continues with the ROM test (see the next section called ROM Test). An error in the processor RAM (located at 40B) is indicated in one of two ways:
- The message 0 OR 7 BAD and some numbers are displayed near the top of the screen, and you should hear a series of rapidly repeating short tones. The selftest is halted and restarted from the beginning. The numbers should help you locate the fault: the first number is the address of the RAM location that had the error, the second number is the bit pattern of the error. You must correct this fault in order for the selftest to continue.
- The message RAM AT’ 40B BAD is displayed, and you should hear a long tone. The message RAM AT 30F BAD and two long tones indicate an error in the color RAM (located at 30F on the Tetris Game PCB). At this point, you can go back and pesform the entire RAM test again by pushing the player 1 joystick to the left. To go on to the ROM test, press the player 1 start button.
ROM Test
¥f there are no errors in ROM, the self-test automatically continues on with the switch test. If the ROM test fails, the message ROM AT 45F BAD xx is displayed (where xx is the checksum of the ROM). To move on to the next test, press the player 1 start button. Chapter 2
Self-Test
Switch Test
The switch test checks the condition of the player controls and other inputs to the game board. The inputs checked are:
SELFTEST PLAYER 2 LEFT VBLANK PLAYER 2 RIGHT
SPARE1 PLAYER 2 DOWN SPARE2 PLAYER 2 ROTATE-START FREEZE PLAYER 1 RIGHT
FREEZE STEP PLAYER 1 LEFT
LEFT COIN PLAYER 1 DOWN RIGHT COIN _ PLAYER 1 ROTATE-START Operate the joystick and button(s) for the right player first, and then the left player. Check that the appropriate messages are highlighted. Be sure to turn off FREEZE and FREEZE STEP (DIP switches 3 and 4 at location 50H) or your game will not perform correctly, SPARE1 and SPARE2 correspond to DIP switches 1 and 2, respectively, but are not used by this game. Also check for the proper operation of the LEFI COIN and RIGHT COIN switches. The SELFTEST and VBLANK messages will always be highlighted. To go on to the next test, press the player 1 start button. Statistics Screen This screen provides current game statistics and the game time histogram. To record all the information displayed in this screen, make photocopies of the statistics sheet printed on the previous page of this manual. The statistics are shown in the upper left area of the screen: « I COIN shows the number of coins deposited in the left coin mechanism.
- RCOIN shows the number of coins deposited in the right coin mechanism. ¢ 2PLYR shows the number of games that were started as a 2-player game. « EASY shows the number of players who started the game at the easy level. e MED shows the number of players who started the game at the medium level.
- HARD shows the number of players who started the game at the hard level.
- ADD-CN shows the number of players that continued their game (add-a-coin).
- OP MINshows the minutes of idle time.
- 1P MINshows the minutes played as a 1-player game.
2-1
Self-Test
¢ 2PMINshows the minutes played as a 2-player game.
- AVG shows the average game time in minutes and seconds, The game time histogram is shown in the middle of the screen. The histogram shows the length of games played in 15-second increments, except as indicated. All statistical information is accumulated from the last time the statistics were reset. To reset the statistics, hold the player 1 joystick to the right, the player 2 joystick to the left, and press the player 2 start bution. The message WORKING appears for about 6 seconds and then the screen will be redrawn with all values zeroed. To go on to the next test, press the player 1 start button.
Coin Options
The coin options scteen indicates the current coin option settings and is used to change those settings. Push the player 1 joystick left or right to select which option to change. Push the player 2 joystick left or right to change the values of the selected option. Note that the factory default of each option is highlighted in green.
- COIN MODE indicates the current cost of each game. © The RIGHT and LEFT MECH MULTIPLIER options each allow you to set various coin denominations.
- BONUS ADDER is used to vary coin denominations or reward players who insert more than one coin at a time. The option of Free Play is also included as one of the BONUS ADDER selections.
To cancel the coin option changes and restore the original settings, press the player 2 start button,
Press the player 1 start button to set the game for the options selected and go on to the next screen. Exiting from the coin options screen by turning off the self-test switch will mot set the game for the selected coin options.
Game Options
The game options screen indicates the current game option settings and is used to change those settings. Push the player 1 joystick left or right to select which option to change, and push the player 2 joystick left or right to change the value of the selected option. Note that the factory default of each option is highlighted in green.
- DIFFICULTY controls the overall difficulty level of the game. ¢ ATTRACT MUSIC controls whether or not music is played during the Attract mode (once every 10 minutes).
- AUTO HIGH-SCORE-TABLE RESET automatically resets
2-2 Tetris/Upright
the high-score table after 2000 games if no player has achieved a high score in the last 200 games. To cancel the game option changes and restore the original settings, press the player 2 start button. Press the player 1 start button to set the selected options and go on to the next screen. Exiting from the game options screen by turning off the self-test switch will not set the selected game options.
EEROM Reset Options
The EEROM ‘eset options screen is used to clear or set certain areas of the EEROM (nonvolatile memory). Move the player 1 joystick left or right to move the red box to the desired option. Note that the factory default of each option is highlighted in green.
- RESET HIGH-SCORE TABiE sets the High-Score Table entries to the defaults stored in ROM.
- SET OPTIONS TO FACTORY DEFAULTS sets the coin and game options to the factory defaults stored in ROM.
- INITIALIZE EEROM initializes the data in EEROM. You should only use this when you have replaced the EEROM device located at 65F because this clears all accounting information. To cancel the EEROM reset options and restore the original settings, press the player 2 start button. Press the player 1 start button to perform the selected resets and go on to the next screen, It may take up to eight seconds to perform the requested resets. If you exit from the EEROM reset screen by turning off the self-test switch, none of the reset options will be performed.
Video Display Tests
You can use the following tests to adjust the video display:
- Screen Paitern Tests Move the player 1 joystick left or right to select among the convergence, color purity, and several other screen patterns. Press the player 2 start button to change colors within each pattern. © Color Test
- 256-Color Test ‘To move from one test to the next, press the player 1 start button.
Audio Test
The audio test indicates the condition of the music and sound-effects circuits. SOUND NUMBER indicates the sound selected by moving the player 2 joystick left (decrements number) or right (increments number), To hear the sound, press the player 2 start button one or more times. Pulling the player 2 joystick down (towards you) silences the audio Pressing the player 1 start button returns to the Switch Test portion of the self-test.
Chapter 3
Troubleshooting
This chapter includes troubleshooting procedures for the Tetris™ kit for upright games.
Video “Noise” Interference
Some game cabinets with switching power supplies exhibit video noise interference. If your cabinet produces this effect, try installing a .1 uF, 50 volt (or greater) ceramic capacitor between the earth ground and logic ground terminals on the switching power supply.
Video Display Sync
Problems
Some video displays cannot use the composite negative sync that is on the JAMMA connector. Tetris includes a standard Atari video connector (located at 15K) that provides separate positive sync. Refer to Table 3-1 and make the appropriate connections for your video display.
Horizontal Shifting
If you cannot center the video display horizontally, you can cause more horizontal shifting by removing R2 and adding a low-resistance resistor (less than 100Q), or a wire in one of the locations marked R1 or R4 (but not both). In Case of Difficulty...
No Raster Nor Video is Visible
- Check that the AC power cord is plugged in, and that the wall circuit is working.
- Check the line fuse on the power supply.
- Check the adjustment for the monitor brightness.
- Check that the power switch is turned on.
- Check all solder connections on the line filter and transformer.
- Check that the 56-pin PCB connector is properly attached to the printed-circuit board.
Raster Visible But No Video
- Check all connections from the PCB to the monitor.
- Check the power-supply voltage on the PCB.
No Video But Game Sounds Can Be Heard
- Check the adjustment for the monitor brightness.
- Check all connections from the PCB to the monitor.
Incorrect Colors are Visible
- Check whether the monitor needs to be degaussed.
- Check for proper wiring between the PCB and monitor.
- Check the monitor adjustments and change them, if necessary.
Wavy Picture is Visible
- Check that the monitor ground is properly connected to the monitor.
- Be certain that the sync inputs are properly connected to the monitor. © Check the monitor's horizontal hold adjustment.
Monitor is Too Dark (and Adjusting Brightness Doesn’t Help)
- Short out resistors R20, R30, and R40 (see Figure 3-1). This should yield a brighter picture.
3-1
Troubleshooting
Vertical/Horizontal Roll or Horizontal Tearing is Visible
- Check the monitor's horizontal and/or vertical adjustments.
- Be certain that the sync inputs are properly connected to the monitor.
Picture is Upside Down
- Switch the horizontal and/or vertical yoke wires of the monitor. ©
No Sound is Produced
- Check the adjustment of the volume control.
- Check for proper voltage on the PCB edge connector.
- Check the wiring from the speaker to the PCB.
- Check the speaker for low resistance (approximately 8Q) between the plus and minus tabs.
Bad Sound is Produced
- Check the speaker's wiring for defective solder connections.
- Check the sound by installing another speaker. Tetris/Upright
No Switch Input
- Check that the ground is properly connected to the switches.
- Check that the wiring between the PCB and switches is correct.
- Check that the switches are operating correctly by using an ohmmeter.
Switch Operates the Wrong Function.
- Check that the wiring between the PCB and switches is correct.
- Check the wiring for shorts between switch inputs.
Coin Meter Doesn’t Work
- Check that the wiring to the coin meter is correct.
- Check that +5V to +12V is on the plus side of the meter.
masynew, AO) See? BSE Guy cs Gea ued Ss Foermmcnmm
Figure 3-1 Shorting Out Resistors on Tetris Game PCB
3-2
Installation ‘Tetris/Upright
Tetris™ Game Statistics
Location:
Date:
Accounting Information Minutes:Seconds
LEFT COINS 0:00-0:15
RIGHT COINS 0:15-0:30
| 2 PLYR STARTS | _—_ | 0:30-0:45 |
EASY STARTS 0:45-1:00
| MEDIUM STARTS | —_ | 1:00-1:15 |
| HARD STARTS | — | 1:15-1:30 |
CONTINUES 1:30-1:45
0 PLY TIME 1:45-2:00
| 1 PLY TIME | —_ | 2:00-2:15 |
2 PLY TIME 2:15-2:30
AVG, GAME TIME 2:30-2:45
2:45-3:00
3:00-3:15
3:15-3:30 —_—
3:30-3:45 —_
3:45-4:00
4:00-4:15
4:15-4:30
4:30-4:45
4:45-5:00
5:00-5:15
5:15-5:30
5:30-5:45
6:00-12:00
12:00+
Photocopy this page Jor use at mubiple locations, ™ and © 1987, AcademySof-Blorg. All rights reserved. Tetris licensed to Andromeda Software Lid; and sublicensed to MIRRORSOFT LID and Sphere, Inc. © 1988 Atari Games Corp. All rights reserved. Original concept, design, and program by Alexey Pazbitnov and Vadim Gerastmou, respectively.
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided: c
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Seller’s plant; and (©) Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
KR