CATHODE RAY TOMES

AquaJet Manual

Aqua Jet (World, AJ2 Ver.B) (Namco, 1996) · Manual · 57 pages · 27 sections · original scan

Page 1

Operators Manual

IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY

AT ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY.

Part No. 90500092

Page 2

© 1996 NAMCO LIMITED all rights reserved.

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for public or private use, without permission from NAMCO EUROPE LIMITED.

While the information contained in this manual is given in good faith and was accurate at the time of printing, NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.

This machine has been manufactured in accordance with European Community Directives, and has been tested and complies with the EMC Directive 89/336/EEC by the application of EN55014 and EN55104 standards (see opposite), and as such bears the ¢ € marking. Any changes or modifications to this machine must be in accordance with European Community Directives. Any unauthorised changes to this product, may contravene such Directives.

Under some conditions of extreme external interference, e.g. radio transmissions, electrostatic discharge or mains borne transients, some degradation of performance may occur. However the machine will recover normal performance once the source of interference has ceased or been removed.

Note:- If the game processor resets due to an interuption or reduction of the mains voltage any credits established may be lost.

This game is not a machine as defined by the Machinery Directive 89/392/EEC

Published by: NAMCO EUROPE LIMITED Namco House, Acton Park Estate, The Vale, London W3 7QE

Phone:- 0208-324-6000 Fax:- 0208-324-6010

Page 3

SAFETY WARNING

In order to use this machine safely, be sure to read this Operators Manual carefully before installation, adjustment or use of this machine. Whenever the owner of this machine entrusts dis-assembly, installation, adjustment or routine maintenance to another person, the owner should ensure that that person read the appropriate precautions and relevant sections of this manual before starting work. In order that no accidents occur when the machine is in operation, strictly follow the notes on safety as described below.

This manual along with the Installation Manual (where applicable) form an integral part of the equipment and must be available to the operating and service personnel at all times.

This machine is for indoor use only and should be used only for the purpose intended.

Namco Ltd. bears no responsibility for accidents, injury or damage resulting from unauthorized changes to, or improper use of this machine.

SAFETY NOTES

The following safety notes are used throughout this manual. Familiarize yourself with each of these notes and its meaning before installing, servicing or making adjustment to this machine.

WARNING Warning denotes a hazard that could result in injury or death. Do not proceed beyond a warning note until the indicated conditions are fully understood and met.
CAUTION Caution denotes a hazard that could result in damage to the machine. Do not proceed beyond a warning note until the indicated conditions are fully understood and met.
Page 4

General Safety Considerations

WARNING Only operate this machine after checking that has been installed correctly and in accordance with the manual.

Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There are warning notices to keep hands and feet clear of moving parts, however if the operator feels that a person is in any danger, he should warn that person accordingly.

The warning notices must always be kept in good condition and replaced if worn, so that the customer can read them clearly.

If there is an error or problem with the machine, operation must be stopped immediately and the problem rectified before any further use.

Installation, service, adjustment or routine maintenance should be carried out by suitably qualified persons only.

For continued protection against fire hazard, replace the mains-in fuses only with the same type and rating. The use of other fuses or material is prohibited.

The power supply inside the monitor will remain hot and have areas of high voltage even though the machine has been turned OFF, and there is the possibility of burns or electric shock. Be careful not to touch these areas.

To prevent possible electric shock due to failure, this machine MUST be fitted with a securely connected EARTHED plug.

If at any time the mains supply lead becomes damaged it must be replaced immediately.

Do not turn the power switch ON until the machine has been installed correctly.

CAUTION Before connecting the machine to the mains supply, ensure that the machine is set for the correct voltage and that the correct fuses are fitted.
Page 5
  • SPECIFICATIONS

POWER SUPPLY:-

AMBIENT OPERATING TEMPERATURE:-

MONITOR:-

COIN ACCEPTOR:-

DIMENSIONS:-

Assembled Front Assembly Ride Assembly Header Assembly Coin Tower

WEIGHT:-

Assembled Front Assembly Ride Assembly Header Assembly Coin Tower

ACCESSORIES:- Keys: 230volts AC

+5°C to +35°C

Pioneer 50” Projector Monitor (SD-V5070NE/MYVZ)

Mars CashFlow - 1 Channel

1265(w) x 2850(d) x 2270(h) 1150(w) x 720(d) x 2070(h) 1150(w) x 2130(d) x 1320(h) 1150(w) x 560(d) x 200(h) 219(w) x 245(d) x 715(h)

534kg 235kg 250kg 25kg 24kg

(Cash Door)... (Coin Door). (Back Door) ...

IEC Mains Lead ... Operators Manual Monitor Manual .... CashFlow Documents

Potentiometer Cashbox Base Plate .. Cash Tower Vac-Form Assy

M10x25 Security Button Head S/Steel M10 Spring Washer S/Steel M10 Flat Washer S/Steel.... M8x60 Hex Head Set Screw S/Steel M8 Spring Washer S/Steel . M8 Flat Washer S/Steel ... M6X30 Hex Head Set Screw - BZP. M6 Spring Washer - BZP. M6 Flat Washer - BZP.. M4X12 Pz Pan Head - BZP M4 Spring Washer - BZP.. M4 Flat Washer - BZP.. M10 Security Wrench M5 Security Wrench... +4 RA RWOWWARROOCO

Page PB

Page 6
  • HOW TO PLAY

This is a racing game for one player. The player can select from two courses, of different difficulty level, and to race for position against the computer.

+ The objective of the game is to cover the selected course as fast as possible within the specified time.

+ If the finish line is reached within the specified time, the player’s position, time and jump distance (*) is displayed and the game is over.

There are three continuous jumping platforms during the course where the player competes for jumping distance. The distances jumped are displayed at game over if the player has reached the finish line within the game time.

+ The game is over if the specified time period reaches 000

  • Operation

+ Steering control is performed by tilting the ride assy to the left or right. Tilt the ride assy to the left to turn left and tilt it right to turn right.

+ The speed is controlled by operating the accelerator lever on the handle of the control arm assembly. Pull the lever to increase speed and release the lever to slow down. If the control arm is raised, the viewpoint moves up, and the viewpoint moves down when the arm is lowered.

+ By moving the control arm up and down rhythmically, it is possible to perform mini jumps at places other than the jump ramps. (expert course only)

+ If the handle arm is held when splashing down onto the water from a jump, it is possible to go under the water for a short time. (expert course only)

  • Starting the Game

+ After inserting the correct amount of money and pressing the start button, the Select Course screen will be displayed. Tilt the ride assy left or right to choose the required course and then operate the accelerator lever to select the course chosen.

+ The game starts when the “GO” sign is displayed on the screen.

+ The game is over if the game time reaches 000

+ If the finish line is reached within the game time, the race results are displayed and the game is over.

+ A player can enter their name if they reach the finish line in a fast time.

Page 7
  • MAJOR COMPONENTS

Header Assy

CPU / PowerSupy Assy Mains-in & Projector Unit On/Off Switch

Control Arm Assy

Front Assy

Kein

Motion-base Assy

Page PB

Page 8
  • Moving the Machine

(— >)

WARNING - When moving or carrying the game, make sure to dis-assemble the game into four parts: header assembly, Front assembly, ride assembly and coin tower.

. The game is fitted with castors to make it easier to move. Take care when moving the machine on an inclined surface.

: The game is still heavy even when separated in to four parts, ensure that there is an adequate number of people to move the game.

7 The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.

: The fitting position of the Header Assembly is very high, and it is important that a means of reaching the height safely, without stretching, is available. (e.g. steps, step stools etc.)

. The overall height of the main assembly is 2300mm, take care of any overhead obstructions e.g. light fixtures. Ne w

NOTE: The Front assembly can be further dismantled by removing the projector from the projector base. (See section 5-1 “Removing the Projector from the Projector Base”.)
Page 9
  • INSTALLATION

Notes on Installation

( WARNING NEVER turn the power to the machine ON until installation > has been completed.

WARNING _in order to prevent possible electric shocks, be sure that the machine is connected to the mains supply with a securely connected earthed plug.
WARNING _ So that customers are not injured by the movement of the Aqua-Jet, ensure that there is at least 500mm separation between other machines or walls.
CAUTION _ In order to avoid damage to the machine due to mis-operation, ensure that the voltage of the mains supply is 230volts AC. Ne yy,

( NOTE If the location site of this machine has a polished floor it is » recommended that rubber pads are fitted under the level adjusters to prevent the machine sliding on the floor.

NOTE In order to gain access to the Power Supply and CPU assemblies] make sure that the rear of the main cabinet is separated from a wall or other machine by at least 500mm. Ne y, 500mm 500mm

500mm

Ys SAFETY ZONE 500mm

PATHWAY E

Page PB

Page 10
WARNING

This machine is designed for indoor use only.

Do not install the machine in the following places.

@® Outdoors @® Direct sunlight, places with excessive humidity or dust, places where there is water leakeage, near ait-conditioning or heating equipment, places with excessively high or cold temperature.

Yn

wet

@ Places where it would be in the way of emergency exits or fire extinguishing equipment. @® Unstable places or Places with excessive vibration. yy ti,

© Places that are not level.

Sy 5

Page 11

5-1 Removing the Projector from the Projector Base.

WARNING =: Make sure that the power is turned OFF before commencing any work.
WARNING +: The projector Assy weighs approx. 100kg. At least four people should be used to remove it from it’s base.
CAUTION + The projector assy. is a precision assembly and should be handled with extreme care, avoiding heavy knocks.
  • Remove the six security screws (M5x30) and remove the front door.
  • Disconnect the two projector connectors.
  • Remove the four hexagonal bolts (M10x130)

Projector unit

Connector

Security Screw (M5 x 30)

Projector base

Flat washer (large) (M10) Front door . Spring washer (M10)

Hexagonal bolt (M10 x 130)

Page PB

Page 12
  • Remove the two security screws (M5x30) and remove the small cover.
  • Remove the two pozi head screws (M5x30), unlock and remove the back door only enough to be able to disconnect the fan connector.
  • Disconnect the fan connector and remove the back door fully.
  • Remove the four hexagonal bolts M10x130.
WARNING After the four hexagonal bolts have been removed, the projector is only resting on the base. Take care that the projector is not accidentally knocked or moved to prevent the projector falling and causing injury.

i Small cover SS 4 Pozi headscrew Security screw {So (M5 x 30) (M5 x 30) —

S Flat washer (large) (M10) oN ;

Back door kK Spring washer (M10)

Hexagonal bolt (M10 x 130)

  • Lift the projector unit up by approx 10cm from the base then carry it backward or forward and gently lower it to the ground.
  • When replacing the projector unit on top of the base, ensure that the guides on the top of the base fit inside the projector unit base.
WARNING Take care not to trap fingers or clothing when replacing the projector unit back on to the base.
Page 13

5-2 Fitting the Header Assembly

WARNING + The Header Assembly has a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.
WARNING + The fitting position of the Header Assembly is very high, and it is important that a means of reaching the height safely, without stretching, is available. (e.g. steps, step stools etc.)
  • Place the Header Assembly on top of the monitor.
  • Lift the right end of the Header Assembly (as viewed from the front), and connect the connector to the top of the monitor. (Ensure that a second person prevents the Header Assembly from falling.)
  • Slide the Header Assembly towards the back of the monitor until it is fully engaged in the locating bracket, taking care not to trap any wires.
  • Fasten the Header Assembly with the 30ff M6x30 Hex head screws, flat and spring washers.

Header assy

Connector

Locating bracket

Projector unit Hexagonal bolt (with flat and spring washer) (M6 x 30) \ Header assy ]

Locating bracket

Page PB

Page 14

5-3 Connecting the Ride Assy to the Front Assy.

  • Push the Ride Assembly close to the Front Assy.
  • Connect the three connectors and the air tube.
  • Push the Ride Assy fully up to the Front assy, taking care not to trap any wires.
  • Fit the Joint Brackets, finger tight, to the Front Assy using 4off Hex Head Set Screws (M8x60), Spring and Flat Washers for each bracket. When all screws have been located, tighten all the screws fully.

Connectors x 3

Air tube

Front Assy

Hex Head Screw (M8x60)

Ride Assy

Page 15

5-4 Assembling the Coin Tower

1.

2: Connect the connector and place the coin tower on to the base assembly.

Attach the coin tower to the base, taking care not to trap any wires, using the nine security button head screws (M10x25), flat and spring washers.

NOTE:- Ensure that the two security screws are fitted to the inside of the cash box area.

M10x25 ‘Security Screw A ~ Spring Washer

Flat Washer Connector

Base Assy

Fit the cashbox plate to the inside of the coin tower using four pozi head screws (M4x12), spring and flat washers.

Security screw (M5x20) F F : / Panel support bracket Place the instruction panel into the panel ad instruction panel support bracket and fasten to the coin Ss cap using the two security screws x (M5x20). APs Coin cap

NOTE:- When the machine is fully assembled and in its final position, lower the 12 level adjusters, (4 on the Monitor Cabinet, 6 on the Ride Assy and 2 on the coin tower), with a spanner so that the machine is level and all castors are raised from the floor by approx. 5mm. Tighten the lock nuts with a spanner to ensure that the level adjusters do not move.

Ride Assy Monitor Cabinet

( | ~Lock Nut Fm

Page PB

Page 16

5-5 Adjusting the Projector

Due to vibration during moving and assembly of the machine, the projector convergence may require adjustment. If this is necessary, adjust the projector using the following procedure. For details on how to adjust the projector, refer to the “Projector Adjustment Manual”.

NOTE: ‘ If the correct adjustment procedure is not followed, or the wrong buttons are pressed, it may be impossible to return the projector to its normal condition.

. The details for adjusting the projector may differ depending upon which projector is used, be sure to follow the adjustment procedure according to the “Projector Adjustment Manual” that is supplied with the game.

  • Remove the six security screws (M5x30) and remove the front door.
  • Adjust the projector according to the “Projector Adjustment Manual”.
  • When adjustment is complete, refit the front door.

Front Assy ——4|

Security screw (M5x30)

Page 17
  • ADJUSTMENTS

done by qualified personnel only.

( WARNING Adjustments or maintenance on this machine should be )

6-1 Turning on the Power

After the machine has been installed, turn ON the power. The Power switch is located on the rear of the Main cabinet. (See section 3 “Major Components” (page 3).)

6-2 Adjustment Switches

The adjustment switches are located inside the coin door.

1. Service Switch Press this switch to obtain game credits without incrementing the play meters.

Test Switch Slide this switch “ON” to enter test mode. Test mode allows game testing and the changing of game settings. (Refer to section 6-3 “Test Mode” (page 14).)

COIN COUNTER COIN COUNTER

°

LEFT PLAYER RIGHT PLAYER

ore FEST on SERVICE TEST SERVICE

Page PB

Page 18

6-3 Test Mode

  • Open the coin door and slide the test switch “ON”. The “Menu Screen” will be displayed on the monitor.
  • Select the test required by moving the control handle up or down. The colour of the selected test will change to red and blink.
  • Enter the selected test by pressing the start button. Select “EXIT” to return to the “Menu Screen”
  • After testing is completed, ensure that the test switch is returned to the “OFF” position to return to game mode.

The Test Switch must always be in the “OFF” position for normal game mode.

(— >) MENU

COIN OPTIONS =— wwwwwnn22---22"2"222====: + (1) Sets the price of play. (See 6-3-1)

GAME OPTIONS = ~wwww-2-"-----"""2"2===: + (2) Sets the game options. (See 6-3-2)

VO TEST «=—-—_—__ wn nnnnnnnnnnnnnnnnnnnee + (3) Used for testing the switches, control potentiometers and air spring. (See 6-3-3)

MONITOR TEST — wwnwwnnnn2-222222220207+ + (4) Used for adjusting the monitor. (See 6-3-4)

SOUND TEST (— wwwwnnennnnnnnnneennen==: + (5) Used for adjusting the speaker volume. (See 6-3-5)

ADS DATA = wwwenennnnnnnnneeenanan: + (6) Displays the accumulated game data.

OTHERS =—___ weeeennnnnnnnnnnnnnnnnan: + (7) Used for testing the PC boards and for initializing all of the settings.

pominee ARM:CHOOSE START:ENTER S

(NOTE):-

. If the control arm has not been initialized correctly, it may not be possible to select items correctly. If this happens, refer to section 7, “Initialization”, and initialize the position of the control arm.

Page 19

6-3-1 Coin Options

Select item (1) “COIN OPTIONS” on the menu screen, to set the game cost and related settings.

Move the Control Arm up or down to select the required item then press the start button.

Press the start button to change the settings.

Select “EXIT” and press the start button to return to the menu screen.

Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the Coin Options on the screen are set as shown in the following table.

( COIN OPTION )

[DEFAULT IN GREEN]

GAME COST PT COIN 1 CREDIT cecessessscctnseeeeceee (a)

FREE PLAY oe (b)

EXIT

\CONTROL ARM:CHOOSE START:CHANGE

ITEM CONTENTS FACTORY SET

  • Game Cost Coins required for one credit - - - - - settable 1-9 1
  • Free Play No coins required for game - - - - - - On / Off OFF

Page PB

Page 20

6-3-2. Game Options

a. Select item (2) “GAME OPTIONS” on the menu screen to set the game options.

b. Move the Control Arm up or down to select the required item.

c. Press the Start button to change the settings. The settings will change each time the start button is pressed.

d. Select “EXIT” and press the start button to return to the menu screen.

Va

GAME TIME STD EXP

SOUND IN ATTRACT

HIGH SCORE INITIALIZE GAME OPTIONS [DEFAULT IN GREEN]

AUTO HI SCORE INITIALIZE STD . ~\

. (a)

  • (b)

(c)

. (See section 6-3-2-1)

EXIT

CONTOL:CHOOSE START:CHANGE Ne /

ITEM DESCRIPTION FACTORY SET

A: No time limit.

B: Long.

  • Difficulty B Cc: Standard.

D: Short.

ON: Attract sound ON.

BGM Only background music.

  • Attract Sound ON EFFECT: Only sound effects.

OFF: No sound. STD: Performed for standard course only.

EXP: Performed for expert course only.

  • High score initialize STD ON: Performed for both courses.

OFF: Not performed.

Page 21

6-3-2-1 High Score Initialization

a. Select “HIGH SCORE INITIALIZE” on the GAME OPTIONS screen and press the start button. The screen will change to the HIGH SCORE INITIALIZE screen.

b. Move the Control Arm up or down to select the required item.

c. The high score is initialized (reset) by pressing the start button, and the screen returns to the GAME OPTIONS screen.

d. If “NO is selected and the start button pressed, nothing is reset and the screen returns to the GAME OPTIONS screen.

( HI SCORE INITIALIZE

NO . Initialization not performed.

YES(STD)vacessssesteseseseseseeey . Only the standard course hi score is reset.
YES(EXP)——ssasissszexseniueneaccenee . Only the expert course hi score is reset.
YES(BOTH):————atarrarscssuaneacvansanaed . The hi score for both courses are reset.

CONTROL:CHOOSE START;ENTER Ne 7

Page PB

Page 22

6-3-3 I/O Test

a. Select item (3) “I/O TEST” on the menu screen.

b. Move the Control Arm up or down to select the required item.

c. Press the start button to enter the selected test.

d. Select “EXIT” and press the start button to return to the menu screen

(~ VO TEST )

DIP 12345678 ecseessseseeed

SWITCH TEST = haneeeaeeseee ee

AIR SPRING TEST so haeeceseeseeey

EXIT

\ CONTROL:CHOOSE START:ENTER

  • Displays the state of the PCB Dip switches, when a switch is ON the number is shown in red.
  • Tests the switches and control potentiometers. (See 6-3-3-1.)
  • Tests the air spring. (See 6-3- 3-2.)
Page 23

6-3-3-1 Switch Test

a. Select “SWITCH TEST” on the menu screen and press the start button. The following screen is displayed.

b. Operate the accelerator lever and start button together to return to menu screen

Va VO TEST

TEST SW ON COIN SW OFF SERVICE SW OFF START BUTTON OFF

ACCELLEVER00000000
SWING00000000
HANDLE POLE00000000

Ne START+LEVER:EXIT ~

CENTRE .l......... (f)

J

(9) Test Switch:

Coin Switch:

Service Switch

Start button

Accelerator Lever

Ship Swing

Handle Pole “ON” during test mode.

‘OFF’ will change to ‘ON’ when the coins to the correct game value have been inserted through the Cashflow acceptor or the coin switch is operated (S18 mech).

‘OFF’ will change to ‘ON’ each time the service switch is pressed.

‘OFF’ will change to ‘ON’ each time the start button is pressed. The button lamp will light each time the button is pressed.

‘FREE’ will change to ‘OK’ each time the lever is operated fully.

‘CENTER’ is displayed when in the central stand by position. ‘RIGHT’ and ‘OK’ is displayed when swung fully to the right. ‘LEFT’ and ‘OK’ is displayed when swung fully to the left.

‘UP OK’ is displayed when the control arm is fully raised, “DOWN OK’ is displayed when the control arm is fully lowered.

NOTE: If ‘OK’ does not appear when the ride is swung to its extreme travel, re-initialize the game as described in section 7

Page PB

Page 24

6-3-3-2 Air Spring Test

WARNING _ The ride moves during the Air Spring test. Ensure that hands and feet are clear before starting the test.

a. Select ‘AIR SPRING’ test on the I/O TEST screen and press the start button. The following screen is displayed.

b. Move the Control Arm up or down to select the required item.

c. Press the start button to enter the selected test.

d. Select “EXIT” and press the start button to return to the menu screen

AIR SPRING TEST

NOW AIR SPRING OFF (DOWN)

GO STATE ON (UP) cnsufessccctsseeee (b)

EXIT

CONTROL:CHOOSE START:SELECT

  • Displays the current position of the air spring.
  • Indicates the direction the air spring will move. Select ‘GO STATE’ and press the start button. If the spring is UP it will go DOWN, and if the spring is DOWN it will go UP.
Page 25

6-3-4 Monitor Test

a. Select “MONITOR TEST” on the menu screen and press the start button. The following screen is displayed.

Select an item by moving the control arm up or down. When the start button is pressed the screen will change to the selected pattern.

To return to MONITOR TEST screen from a test pattern, press the start button.

Select “EXIT” and press the start button to return to the menu screen

(— MONITOR TEST >)

GRADATION PATTERN CROSSHATCH PATTERN [CRT] CROSSHATCH PATTERN [PROJECTOR] WHITE WINDOW [H] WHITE WINDOW [M] WHITE WINDOW [L] INTERLACE PATTERN VIEW ANGLE ADJUST [CRT] VIEW ANGLE ADJUST [PROJECTOR] FULL WHITE

EXIT

CONTROL:CHOOSE START:ENTER N

Page PB

Page 26

6-3-5 Sound Test

a. Select “SOUND TEST ” on the menu screen and press the start button. The following screen is displayed.

b. Move the Control Arm up or down to select the required item.

c. Press the start button to enter the selected test.

d. Move the control arm up or down to alter the setting of the selected item.

d. Select “EXIT” and press the start button to return to the menu screen

(— SOUND TEST >) *[DEFAULT IN GREEN]

GAME VOLUME FRONT SP 2C TANK SP 2C

ATTRACT VOLUME 20 reeediseeeeeees (c)

REQUEST SONG NO. [0] 0 mereen Cremreresreces (d)

MESSAGE ee ee _The selected song description is displayed EXIT

CONTROL:CHOOSE START:ENTER Ne yy,

Front speaker volume Adjusts the volume of speakers in the header.

Tank speaker volume Adjusts the volume of the tank speaker on the ride.

Attraction volume Adjusts the volume during attract mode.

Sound selection Each digit of the REQUEST SONG No. can be changed by moving the control arm up or down. Each number will produce a different tune or sound when the start button is pressed. 001 will produce a stereo test. First a tone will be produced from the front speakers, then from the tank speaker and then from all speakers.

Page 27

6-3-6 ADS Data

Select “ADS DATA ” on the menu screen and press the start button.

The book keeping data for the game will be displayed.

6-3-7 Others

Select “OTHERS” on the menu screen and press the start button.

This screen is used to test the PCB and to reset the game to factory settings.

Page PB

Page 28

INITIALIZATION

Adjustments When Replacing Parts (Initialization)

The following adjustments should always be performed after replacing the game PC board, ROM, or Control Pots. The game will not operate correctly if these adjustments are not made.

  • Ensure that Control Handle assembly and Ride assembly are in the neutral stand-by position.
  • Slide the test switch “ON” while pressing the service switch. The following screen will be displayed on the monitor. (— VOLUME INITIALIZE >)

TEST Sw ON COIN SW OFF SERVICE SW OFF START BUTTON OFF

ACCEL LEVER 0000 0000 SWING 0000 0000 CENTRE HANDLE POLE 0000 0000 UP

START:HANDLE POLE ADJUST Ne w

  • Atthis time the Ride assembly and Accelerator lever are initialized.
  • Press the start button to initialize the Control Arm. The following screen will be displayed.

HANDLE POLE ADJUST

UP DOWN HANDLE POLE 0000 0000

PLEASE MAKE HANDLE POLE UPDOWN TO ADJUST!

  • Move the Control Arm UP and DOWN through its full range of movement. This motion will be registered as the motion range of the Control Arm.
  • Slide the test switch “OFF” to return to normal game mode.
Page 29
  • REMOVING AND REPLACING ASSEMBLIES AND PARTS.
WARNING

Adjustments or maintenance on this machine should be carried out by qualified personnel only.

Do not make any alterations to this machine without prior approval. Doing so could cause unforeseeable danger.

Only parts specified by Namco Europe Ltd. should be used when replacing or repairing parts (including screws).

Ensure that power to the machine is turned OFF before commencing any maintenance work (troubleshooting, repairs etc.)

If performing work not described in this manual, be sure to contact your distributor for instructions as no responsibility will be accepted for damage or injury.

Parts of the power supply, projector monitor and air compressor remain hot or carry high voltage even after switching OFF and could cause burns or electric shock. Take care not to touch these parts accidentally.

Make sure that the machine is switched OFF before connecting or disconnecting any plugs or connectors.

When removing the mains connector from the machine, or the mains plug from the wall outlet, always grasp the plug not the cable. TS

8-1 COMPRESSOR ASSEMBLY

NOTE:

There are no user serviceable parts on the compressor assembly.

Under no circumstances should any regulator valves be adjusted. Altering the requlator valves could lead to serious damage to the system or injury to personnel

WARNING

Parts of the compressor become very hot during use. Take care not to touch the compressor when it is hot.

Page PB

Page 30

8-2 Ride Assembly

8-2-1 Replacing the Swing Potentiometer

WARNING + Make sure that the power is turned OFF before commencing any work. + Do not let any one get on the ride assembly while replacing the potentiometer to prevent injury by trapped hands or fingers.
  • Remove the two pozi head screws (with flat and spring washers)(M5x10) and remove the potentiometer cover.
  • Remove the two pozi head screws (with flat and spring washers)(M5x10) and remove the maintenance cover.

Pozi head screw (with flat and spring washer) (M5 x 10)

Pozi head screw (with flat and spring washer) (MS x 10) Potentiometer cover

  • Disconnect the connector. Loosen the grub screw (M4x12) and remove the potentiometer complete with its mounting bracket.

Connector Flat surface on the shaft

Page 31
  • Remove the potentiometer from the mounting bracket and replace with a new potentiometer.
  • Re-assemble in reverse order.
NOTE: When refitting the potentiometer and bracket ensure that the grub screw engages on the flat of the potentiometer shaft, and the notch in the mounting bracket engages on the pin.
  • Re-initialize the game. (Refer to section 7 ‘Initialization’)

8-2-2 Removing the Tank

WARNING =: Make sure that the power is turned OFF before commencing any work.
  • Remove the four security screws (M5x12) and four security screws (M5x20), and remove the tank.
  • Re-assemble in reverse order.

Security screw (M5x12)

g Tank

Security screw (M5x20)

Security screw (M5x20) Security screw (M5x20)

Page PB

Page 32

8-2-3. Replacing Solenoid Valve A

WARNING + Make sure that the power is turned OFF before commencing any work.
  • Remove the tank. (Refer to section 8-2-2 ‘Removing the Tank’
  • Disconnect the connector.
  • Push the blue release of the elbow union in, and while holding it in, pull out the air tube. (There will be a loud noise as the air pressure is released.)
  • Remove the two pozi head screws (M4x35) and remove the solenoid valve A.
  • Remove the elbow union, half union and silencer from the removed solenoid valve, and install them on to the new solenoid valve.
  • Re-assemble in reverse order. (The air tube is just a push fit.)

Connectors

Haif union A-port = elbow union Silencer P-port = half union R-port = silencer

Elbow union

NOTE: . Take care that no dirt or other matter gets in to the air tube while it is disconnected. 7 After refitting the air tube, give it a gentle pull to ensure that it is connected properly and will not come loose.
Page 33

8-2-4 Replacing Solenoid Valve B

WARNING =: Make sure that the power is turned OFF before commencing any work.
  • Remove the tank. (Refer to section 8-2-2 ‘Removing the Tank’
  • Disconnect the connector.
  • Push the blue release of the elbow union in, and while holding it in, pull out the air tube. (There will be a loud noise as the air pressure is released.)
  • Remove the two pozi head screws (M4x35) and remove the solenoid valve B.
  • Remove the half union, taper-screw plug and silencer from the removed solenoid valve, and install them on to the new solenoid valve.
  • Re-assemble in reverse order. (The air tube is just a push fit.)

Solenoid valve A <\

Silencer

Taper-screw plug | secens valve B A-port = half union P-port = taper-screw plug Connectors Report = silencer Haif union

Blue release Pozi head screw (M4x35)

A Cone Pull the tube

NOTE: . Take care that no dirt or other matter gets in to the air tube while it is disconnected. . After refitting the air tube, give it a gentle pull to ensure that it is connected properly and will not come loose.

Page PB

Page 34

8-3 Control Arm Assembly

8-3-1 Replacing the Accelerator Potentiometer

WARNING + Make sure that the power is turned OFF before commencing any work.
  • Remove the four security screws (M5x12) and remove the accelerator cover.

Accelerator cover

  • Disconnect the connector. Loosen the grub screw (M3x5) and remove the potentiometer complete with its mounting bracket.
  • Remove the potentiometer from the mounting bracket and replace with a new potentiometer.
  • Re-assemble in reverse order.

Potentiometer Flat surface on the shaft

> Mounting bracket Connector —

Hamesses

Grub screw (M3 x 5) ——"®

Cord clip

NOTE: When refitting the potentiometer and bracket ensure that the grub screw engages on the flat of the potentiometer shaft, and the wire harness is secured with the two cord grips so that it does not get caught or pinched by the moveable section.
  • Re-initialize the game. (Refer to section 7 ‘Initialization’)
Page 35

8-3-2 Replacing the Control Arm Potentiometer

WARNING +: Make sure that the power is turned OFF before commencing any work.
  • Remove the tank. (Refer to section 8-2-2 ‘Removing the Tank’).
  • Disconnect the connector. Loosen the grub screw (M4x5) and remove the potentiometer complete with its mounting bracket.
  • Remove the potentiometer from the mounting bracket and replace with a new potentiometer.
  • Re-assemble in reverse order.
NOTE: When refitting the potentiometer and bracket ensure that the grub screw engages on the flat of the potentiometer shaft, and the lug on the mounting bracket engages in the slot of the main metalwork.
  • Re-initialize the game. (Refer to section 7 ‘Initialization’)

Connector

OD =(2

Flat surface on the shaft

Potentiometer

Page PB

Page 36

8-3-3 Replacing the Start Switch or Lamp

WARNING + Make sure that the power is turned OFF before commencing any work.
  • Remove the eight security screws (M5x12) and lift the top vac-form sufficiently to remove the switch and lamp from the push button.
  • Remove the top vac-form.
  • Replace the lamp or switch.
  • Re-assemble in reverse order.

S— Start button

Security screw (M5x12)

PA

Start switch F rack

Orange _—N\reston terminal

Violet

Page 37

8-4 Header Assembly

8-4-1 Replacing the Fluorescent Lamp or Starter

WARNING =: Make sure that the power is turned OFF before commencing any work.
WARNING + The Header Assembly is very high, and it is important that a means of reaching the height safely, without stretching, is available. (e.g. steps, step stools etc.)
WARNING =: The fluorescent lamp may be hot, take care when handling.
  • Remove the four security screws (M5x20), and remove the acrylic sign board.
  • Replace the fluorescent lamp or starter.
  • Re-assemble in reverse order.

Fluorescent lam Header assy e Starter

Secrity screw (M5x20)

Page PB

Page 38
  • PARTS

Header Assy

£ yi

ITEM DESCRIPTION PART No

1HEADER CABINET37100110
2LOUDSPEAKER GRILLE46000083
4HEADER ACRYLIC30000234
=ACRYLIC RETAINING BRACKET46000084
EtFLOURESCENT TUBE 18" 15W64500009
—3|LOUDSPEAKER 5%" FULL RANGE62000065
E4| STARTER 240v 4-80W UNIVERSAL63000000
—5|STARTER HOLDER64800001

M6x16 HEX HEAD SET SCREW - BZP 26500311

BIM6 SPRING WASHER - BZP28000028

M6 FLAT WASHER - BZP 28000166

M4x16 PZ PAN HEAD - BLACK 26300294

B2|M4 SPRING WASHER - BLACK28000127

M4 FLAT WASHER - BLACK 28000132

B3_|M5x20 SECURITY BUTTON HEAD - SUS26300039

B6 | No4x¥" PZ PAN HEAD WOODSCREW - BZP. 26100070

B7|M4x12 PZ PAN HEAD - BZP26300057
BS|M4x16 PZ PAN HEAD - BZP26300383
BQ|M4 WHIZZTITE NUT - YEL ZNC27000128
Page 39

Coin Tower

CIN ee ON

B7

ITEM DESCRIPTION PART No

1|COIN TOWER TOP VAC-FORM46000057

2 | INSTRUCTION DECAL SUPPORT BRACKET 46000146

3|PLAY INSTRUCTION DECAL - ACRYLIC30000235
5_|WOODEN CASHBOX37100093
6|M12 ADJUSABLE FOOT88300311
7|3.5-6v METER - PANEL MOUNT65000002

8 | MINIATURE SLIDE SWITCH - DPCO. 60000023

9|SERVICE SWITCH 7mm RED - F42460000059

B1 | No8x%" PZ CSK WOODSCREW - BZP 26100265

B2_|M3x10 PZ PAN HEAD - BZP26300067
B7_|MS5x16 SECURITY BUTTON HEAD - SUS26300032
B8_|MS5x20 SECURITY BUTTON HEAD - SUS26300039

B9 | MS5x14 RAWLNUT 27000153

Page 40

Cabinet Base

©

TEMDESCRIPTIONPART NoTrewDESORIPTIONPART No
1_[INTERLOGK swiTcH‘600000815[Fuse ty" 1A08Cd
|areROC eno COVERry76 _ [COMPRESSOR ASGY TYPE 600 WILOW READ GAUGE“46000058

7 _ [FAN a0 a0 7000015

‘3|SCHAFFNER 10A DOUBLE FUSED MAINS IN FILTER(62500011
78_[ROTARY FAN“45000040
4__[SHARFNER BOOT. 189,Senne79 _ [PLASTIC STARTER CAPACITOR~a6000081
5| 10A20mm FUSE163500705moSSAeo00T6s
6 _ [SWIVEL CASTOR Tamm59000005Bi_|MSx20 PZ PAN HEAD - BZP25800576
7__[Mie ADJUSTABLE FOOT188900079MS SPRING WASHER -BZP2000745
@[CONDENSATE BOTTLE O5tr“46000078MS FLAT WASHER - 822000744
9[WOODEN BLANKING STRIP37100108E>[heeiea) Ae PA HEAD Eee25300065
70 _ [AQUA JET SUPER SYSTEM 22 POB ASSYXALPCBhicksichieeaiita odseme

Ma FLAT WASHER -2P 28000036

11[4CHANNEL AMP PCB - SUPER SYSTEM 22XCYB-AMPCB
BG_|Mex25 HEX HEAD SET SCREW - 82>25200050,
12 _ [LAMP DRIVER POS - SINGLE CHANNEL“46000020Ne PRNG WAEHERTEXP——
13[2 CHANNEL AMPLIFIER - Vera46000036fie FLAT WASHER - B2P2000175
14[ASTEC SA207-0400 SMPSU 530A188000001a|MSxa0 PZ PAN HEAD -BZP25300505
Page 41

Cabinet

x

om)

  • 2

B2

ITEM DESCRIPTION PART No

1| PIONEER REAR PROJECTION MONITOR 230v84000028
2|CABINET FRONT PANEL37100106
3|LOUDSPEAKER GRILLE45000701
4|HARNESS CONNECTOR BRACKET46000082
5_|ADJUSTABLE FOOT MOUNTING BRACKET45000204

6 | SIDE DECAL - LHS/RHS. 40000381

7|FAN 4%" 230v67000015
8|FRONT DECAL40000383
9_|LOUDSPEAKER 6%" - BASS62000068

B1_|MS5x30 SECURITY BUTTON HEAD - SUS 26300036

M5x25 PZ PAN HEAD - BZP 26300049

B2__|MS5 SPRING WASHER - BZP 28000144

Ms FLAT WASHER - BZP 28000145

M10x130 HEX HEAD SET SCREW - BZP 26500475

B3__|M10 SPRING WASHER - BZP 28000023

PIONEER CLAMP WASHER 46000163

Page 42

Control Arm

ITEM DESCRIPTION PART No

1CONTROL ARM TOP VAC-FORM46000054
2NAMCO DECAL40000390
3AQUAJET DECAL40000389
4ACCELERATOR DECAL40000392
5HANDLEBAR COVER VAC-FORM46000055
6CONTROL ARM BOTTOM VAC-FORM46000053
7RPB RECTANGULAR PUSH BUTTON - YELLOW "START"60500044
8START DECAL40000391
9WARNING DECAL40000393
10HANDLEBAR GRIP - LHS/RHS46000141
BiM5x16 SECURITY BUTTON HEAD - SUS26300032
Page 43

ITEM DESCRIPTION PART No

2RUBBER STOPPER RI-3046000007
3PITCH SPRING BUMPER46000075
4PITCH SPRING46000073
5PITCH STOPPER RUBBER BLOCK46000072
6PITCH POTENTIOMETER MOUNTING BRACKET46000132
7PITCH POTENTIOMETERX008-021
8BEARING UCP-206-NSK46000080
9SPRING SLEEVE46000131

M16 FULL NUT - BZP 27000205

°M16 SPRING WASHER - BZP28000301
1BEARING SECURING WASHER 40 OD x 17 ID x 3.2T46000133
12BEARING SPACER46000130
13PITCH MAIN SHAFT46000129

M4x12 PZ PAN HEAD - BZP 26300057

B1M4 SPRING WASHER - BZP28000035

M4 FLAT WASHER - BZP 28000036

B3M4x8 HEX SOCKET SET SCREW - BZP26300083

M14x50 HEX HEAD SET SCREW - BZP 26500502

B4M14 SPRING WASHER - BZP28000302

M14 FLAT WASHER - BZP 28000021

BSM8x20 SOCKET HEAD CSK SCREW - BZP26300862
Page 44

Accelerator

ITEM DESCRIPTION PART No

1HANDLEBAR METALWORK46000134
12ACCELERATOR PLATE46000135
13,ACCELERATOR POTENTIOMETER SHAFT46000136
14ACCELERATOR POTENTIOMETER BRACKET46000137
15,ACCELERATOR SPRING STOP PIN46000138
16ACCELERATOR LIMIT STOP TUBE46000139
17ACCELERATOR LIMIT STOP BUMPER46000074
18ACCELERATOR SPRING46000157
19ACCELERATOR SLIDE COVER46000140
25ACCELERATOR HANDLE46000076
27SPACER - 8mm OD x 3mm LONG46000142
29OILITE BUSHING LFF 070546000077
30OILITE BUSHING LFF 101246000078
£4ACCELERATOR POTENTIOMETERX008-021
B7M3x5 HEX SOCKET SET SCREW - BZP26300111
B10| M5 WHIZZTITE NUT - BZP.27000151

M5x8 PZ PAN HEAD - BZP 26300570

B15|M5 SPRING WASHER - BZP.28000144

3/16" x 3/4" FLAT WASHER - BZP_ 28000224

Page 45

Ride Assy

ITeM DESCRIPTION PART No

2| RIDE STAND-ON WOODEN PLATE37100111
5|LOUDSPEAKER MOUNTING WOOD,37100112
6|LOUDSPEAKER MESH46000120
24| AIR VALVE VK334-6GS-01 12vDC46000069
25_|CONNECTOR KQL08-01S46000147
26_|CONNECTOR KQH08-01S46000148
27_|CONNECTOR KQU08-1046000149
28{CONNECTOR KQL10-0046000150
29| AN103-0146000126
30[PLUG 1/846000167
32| TUBE TU10658 50mm46000151
33| TUBE TU0805B 55mm46000155
38|CONTROL ARM WOOD SUPPORT BRACKET46000162
£2_|LOUDSPEAKER 5%" FULL RANGE62000065

M4x20 PZ PAN HEAD - BLACK 26300391

Bi|M4 SPRING WASHER - BLACK28000127

M4 FLAT WASHER - BLACK 28000132

M4x40 PZ PAN HEAD - BZP 26300443

©?Tita SPRING WASHER - BZP28000035

M5x16 PZ PAN HEAD - BZP 26300580

B3_|Ms SPRING WASHER - BZP28000144

M5 FLAT WASHER - BZP 28000145

M5x35 PZ PAN HEAD - BZP 26300613

BS_|M5 SPRING WASHER - BZP28000144

M5 FLAT WASHER - BZP 28000145

B9| No6x’" PZ FLANGE - BZP26100074
Page 46

ITEM DESCRIPTION PART No

1RIDE STAND-ON METAL BASE46000117
3SIDE VAC-FORM SUPPORT BRACKET - LHS46000118
4SIDE VAC-FORM SUPPORT BRACKET - RHS-46000119
8SIDE VAC-FORM MOUNTING BRACKET46000122
10REAR VAC-FORM CLOSING BRACKET46000124
31TUBE TU1065-B46000151

M8x20 HEX HEAD SET SCREW - BZP 88300700

BiM8 SPRING WASHER - BZP28000176

M8 FLAT WASHER - BZP- 28000175

M5x16 PZ PAN HEAD - BZP 26300580

B3M5 SPRING WASHER - BZP28000144

M5 FLAT WASHER - BZP- 28000145

M5x25 PZ PAN HEAD - BZP 26300049

B4M5 SPRING WASHER - BZP28000144

M5 FLAT WASHER - BZP- 28000145

M4x10 PZ PAN HEAD - BZP 26300366

B10M4 SPRING WASHER - BZP28000035

M4 FLAT WASHER - BZP- 28000036

Page 47

Ride Vac-Forms and Decals

ITEM DESCRIPTION PART No

7|FRONT VAC-FORM MOUNTING BRACKET46000121
11|LOWER VAC-FORM - RHS46000049
12|LOWER VAC-FORM - LHS46000048
13|UPPER STANDING AREA VAC-FORM46000050
14| REAR VAC-FORM46000051
15|TOP FRONT VAC-FORM46000052
16|REAR EXHAUST DECAL40000384

17 _ | SIDE FLASH DECAL - LHS UPPER 40000385

18_|SIDE FLASH DECAL - RHS UPPER40000386
19| SIDE FLASH DECAL - LHS LOWER40000387

20 | SIDE FLASH DECAL - RHS LOWER 40000388

21|3M ANTI SLIP FLOOR MAT - STANDING AREA46000070
22|FRONT VAC-FORM CLOSING BRACKET46000125
35_|SUPERVISION WARNING DECAL40000396

M5x16 SECURITY BUTTON HEAD - SUS 26300032

®MS FLAT WASHER- SUS28000015
B7_|MSx25 SECURITY BUTTON HEAD - SUS26300033
Bs|MS5x14 RAWLNUT27000153
Page 48

ei

DESCRIPTION

PART No

MAIN FLOOR SIDE COVER - RHS. 46000083

MAIN FLOOR SIDE COVER - LHS. 46000092

AIR SPRING MOUNTING BRACKET - UPPER,

“46000017

8M ANTI SLIP FLOOR MAT - REAR BASE

46000071

BASE WARNING DECAL

40000384

‘CONNECTOR KQL10-U02 46000161

MSx16 SECURITY BUTTON HEAD - SUS. 26300082

‘18°x3/4" HEX HEAD SET SCREW - BZP 26500901

PARTS NOT SHOWN

RUBBER SKIRT - LHS 46000168

RUBBER SKIRT - RHS "46000169

RUBBER SKIRT FIXING PLATE - BASE ‘46000170

RUBBER SKIRT FIXING PLATE - RIDE ‘46000171 B10 Ride Base Assy

Page 49

ITEM

DESCRIPTION

PART No.

RIDE BASE

‘46000087

‘STEERING ARM MOUNTING BRACKET RUBBER STOPPER - I-30 ‘AIR SPRING

46000106

RUBBER STOPPER - RI/65/HD_ “46000059

‘46000007

46000060

LINK BALL -TBS12

46000062

‘SHOCK ABSORBER - FK/2530/S/NM1 46000064

SIDE LOAD ADAPTOR - KG/001/NM 46000065

Be

10x25 HEX HEAD SET SCREW - BZP M10 SPRING WASHER - BZP

26500134

28000023

M10 FLAT WASHER - BZP_ 28000198

Bio 3/8" x 1 3/16" HEX HEAD SET SCREW - BZP. 26500902

3/8" SPRING WASHER - BZP. 28000213

9/8" FLAT WASHER - HEAVY DUTY - BZP. 28000214

Bia

M12 NYLOG NUT -BZP

27000201

M12 FLAT WASHER - BZP 28000020

Page 50

‘a

SS

DESCRIPTION

PART No

MAIN FLOOR BASE

46000086

ROSTA SPRING SHAFT MOUNTING ASSY

46000088

YAW DRIVE SHAFT

46000090

YAW MECHANICAL STOPPER MNTG BRACKET HARDENED BLOCK

46000094

46000108

SWIVEL CASTOR 75mm 59000005

ADJUSTABLE FOOT M20x70 46000160

Bt M4x12 PZ PAN HEAD - BZP 26300336

M4 SPRING WASHER - BZP 28000035

M4 FLAT WASHER - BZP 28000036

B4 M6x16 HEX HEAD SET SCREW - BZP 26500311

M6 SPRING WASHER - BZP 28000028

M6 FLAT WASHER - BZP 28000037

BS M8x30 HEX HEAD SET SCREW - BZP 26500407

M8 SPRING WASHER - BZP 28000176

M8 FLAT WASHER - BZP 28000175

Be 10x25 HEX HEAD SET SCREW - BZP 26500134

M10 SPRING WASHER - BZP 28000023

M10 FLAT WASHER - BZP 28000198

ITEMS NOT SHOWN

"FORK HERE" DECAL 40000072

BASE SIDE WARNING DECAL 40000394 @

Page 51

DESCRIPTION

PART No.

ROSTA SPRING MOUNTING SHAFT

46000095

LINK BALL MOUNTING SHAFT

46000098

ROSTA SPRING RETAINING WASHER ROSTA SPACER WASHER

46000102

46000103

ROSTA RETAINING BRACKET

46000104

ROSTA SPRING REAR PACKING BRACKET 46000114

ROD EYE - RBL16BD 46000063

ROSTA SPRING DR-S-27x60 46000067

BEARING - UCPA/204/FYH 46000068

M16x40 SOCKET HEAD CAP SCREW - BZP 26500602

Bo Méx16 HEX HEAD SET SCREW - BZP 26500311 ee,

M6 SPRING WASHER - BZP 28000028

M6 FLAT WASHER - BZP 28000037

B13 M12x25 CSK CAP SCREW - BZP 26300940

Bid M12 FULL NUT - BZP 27000022

BI7 M12 SPRING WASHER - BZP 28000019

B19 M12 FLAT WASHER - BZP 28000020

Page 52

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 53

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 54

10.SCHEMATICS

i I BASE ASSY RIDE A

\ ! — !

i

\

i Ho seen ro cReen can = eLLow ete Hater —t 3 T8 FST ack as re tpiicecace — S18 repeace ae] gsr Nvveccow} 218 i I i

Lo \

i I eIMe supic i 4 Howe ey mo ce fwioreveen a. 2 wire /opance 2+ ete vet He ftorevacace pS 18 re fwroreveueece ST fi SWHITE7oREEN E S$ fwioreveeow a ae Ef 39 ia Tarn A ii [at — Go eeeewvenow [tte a stat 4tat I s[st+ eret

1 Beown+an

Hat a0

2 oReyeteete}

fren acne a5 4 RED ALLE ne Sen me ats

pe etoeae_
Paxae7
reaeHat

m7 ae

He]|set

fe 6i6 i Uy ceeeuvetioy i

i

LeeiL;
Page 55

IDE ASSY CONTROL ARM ASSY

CONTROL ARH i | [AR] | !

TT SER VALVEii
2 patie vatii
ro Be aR\'

VALUE

i | :

tTcH seen wireick r\
22 ey varTeateglei
348ataa3|
ataataata
ated wy acyata|'

n STS Vrore PURPLE, ste 8S WHITE eae ets WHITE Recht pa 1

JomS18 ceeen/VELLOate!

ad i TE | ie [ot an

!iti

ze +S vRe

|a4i

' 2 ' H 3 ACCELERATOR | oare \

ae+e VRSi
a8‘|

i

I

SEVICE

Be test ;

ne

aE PINk/aeN} BE CHANNEL

a COIN TOWER ASSY

Page 56

‘BROWN

one

Lue Fane

posta

FILTER FAM a

PROJECTOR Ass TERT SRE LEFT SPER = HET Seke > [eager see =

conPRESSoR asst Heaner assy

r

x

r EERE

Te ee LS

Bier see Ft HL Ela see Lie He

RET] Vereen ete cere ot z rots +

a z

a vem ty va ats

i T

a T

‘

BROWHL en

PURPLE RANE

REEL

BEECH. BLL

sare BEALE cove, eee ELL BLE

ware

BLATE

z

a

a8

TEA a Tae [arar

1 AW Four channen,

THREE CHANEL, ANPLETER

  • momen a !

I [R

Page 57

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.