CATHODE RAY TOMES

Race Drivin' Cockpit TM-351 2nd Pritning

Race Drivin' (cockpit, rev 5) (Atari Games, 1990) · Technical Manual · 120 pages · 128 sections · original scan

Page 1

GAMES

Operator’s Manual

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

A, ATARI | GAMES|

OPERATOR’S MANUAL

with flustrated Parts Lists

Palents are panding on several pans of he Race Davin’ simutator.

Page 4

Copyright © 1988, 1989, 1990 by Atari Games Corporation. All rights reserved, No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a rewieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, ali graphic designs, this technical manval, its accompanying schematic diagcams, and the display manual are protected by the U.S, Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws, Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles, In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corparations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, diswibuuion, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game, Published by: Atari Games Corporation 675 Sycamore Drive RO. Box 361110 Milpitas, California 95036 Printed in the U.S.A. 13/90 Produced by the Atari Games Technical Publications Department. Writing & Editing: Andrea Dencker Illustration & Design: Mary Ohanessian Summer Rage Drivin’

Notice Regarding Non-Atari* Parts

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, end may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: Wi Substitute non-Atari parts in the game. @ Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation,

NOTE ‘This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in 2 residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: @ Ail ground wires in the game are properly connected as shown in the game wiring diagram. @ The power cord is properly plugged into a grounded three-wire outtet. @ On games provided with an Electromagnetic Interference (EMI) ground cage, be sure that the game ptinted-circait boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with all screws in place and tightened, if you are stil unable to solve the interference problem, please contact Customer Service at Atati Games Corporation. See the inside front cover of this manual for service in your area,
Page 5

Race Drivin’

Table of Contents 1 Set Up How to Use This Manual 1 Operating the Simulator. 2 Inspecting the Simulator. 1-2 Installing the Attraction Sign Assembly. 1-2 Adjusting the Glides ,. 13 Control and Switch Locations 143 Setting the Coin and Game Options. 1-3 Simulator Systerns.. 13 Maximizing Earnings 1-4 Simulator Driving, 14 2 Self-Test Entering and Exiting the Self-Test 22 Automated Self-Test 22 Program ROM and RAM Test... 23 Microprocessor and Board Tests. 2-3 ‘Test Menu Screens... 4 Operator Screens 24 Coin Options... 24 Game Difficull

Histogram.

Control Inputs Screen. Monitor Test Patterns Set Clock Screen .... Disable Broken Controls Screen Special Functions Screen. Main Board GSP Tests Main Board Controls. Steering Wheel Subm Shifter Test Screen , Link Connector Tes! Main Board ROM Checksums .. Main Board ZRAM Test ADSP Board Tests... Sound Board ....... DSK Hoard Tests...... LEDs on the Main PCR DIP Switches 3 Maintenance and Troubleshooting Maintaining and Lospecting Maintaining Your Simulator..

Removing the Dashboar installing the Dashboard Steering Assembly ... Greasing the Steering “Assembly Replacing the Steering Assembly Potentiomete: Replacing the Steering Wheel Motor Replacing the Steering Whee! Stop Key Switch Assembly . Oiling the Key Switch * soem Replacing the Spring in the Key Switch Asser Tightening the Screw in the Key Switch Achiator... _ Replacing the Switch on the Key Si Clutch Pedal ,, Maintaining the | Clutch and Brake Pedals Replacing the Clutch Potentiometer Replacing the Clutch Springs.......

Repairing the Brake Testing the Switch, S and Pedal Movement... Testing the Stain Gauge and the ouu Bonding. Replacing the Brake Switc! Replacing the Brake Strain Gauge and Pedal Assembly ... Gas Pedal ‘Assembly... Lubricating the Gas Pedal Rewinding the Gas Pedal Puliey Cable Replacing the Gas Pedal Cable Spring Replacing the Gas Pedal Potentiometer Replacing a Broken Spring on the Gas Pedal Shifter Assembly... installing a New Shifter Boot Removing the Reverse Latch Pin Replacing a Shifter Potentiometer.. Replacing the Shifter Solenoid. Seat Assembly .... Replacing the Seat ‘Rod End Bearings Replacing Bearings on the Seat Pivot Replacing Main Seat Bearings. Replacing dhe Gears on the Seat Replacing the Small Gear. Replacing the Large Gear.. Replacing the Magnet on the Seat Assembh Replacing the Seat Potentiometer............ Video Display . Removing the Video Display . Replacing the Video Displa

it

Page 6

Motor Amplifier Assembiy .... Removing the Motor Amplifier ‘Assembly Speakers -.. Removing a Speaker PC Board Stack. Removing a Board from the PC Board Stack Replacing Static-Sensitive Devices. Cleaning the Coin Mechanism... Cleaning the Interior Components... 4 Illustrated Parts Lists See the List of Illustrations that follows.

Statistics Sheet

List of Hlustrations Figure 1-1 Attraction Sign Installation .. ee 1-3

Figure 2-1 Program ROM and RAM Test Screen Figure 2-2 Microprocessor and Board Tests Screen Figure 2-3. Instructions for Test Menu Screen Figure 2-4 Test Menu Screen .. Figure 2-5 Cain Options Screen Figure 2-6 Game Difficulty Scree:

Figure 2-7 Custom Game Options Screen. Figure 2-8 Game Options Screen Figure 2-9 Statistics Screen... Figure 2-10 Histogram Screen. Figure 2-11 Games Played by Day an Figure 2-12 First Set Controls Screen. Figure 2-13 Control Inputs Screen, Figure 2-14 Set Clock Screen. Figure 2-15 Disable Broken Com Figure 2-14 Special Functions Scree! Figure 2-17 GSP ‘Tests Screen ....... Figure 2-18 Main Board Controls Screen Figure 2-19 Pots: 8-Bit Screen Figure 2-20 Pots: 12-Bit Screen. Figure 2-21 Figure 2-22 Figure 2-23 Figure 2. Figure Figure 2-26 Figure 2-27 Figure 2-28 Figure 2-29

Figure 2-30 Figure 2-31]

Figure 3-1

Figure 3-2

Figure 3-3

Figure 3-4

Figure 3-3 Figure 3-6

Figure 3-7

Figure 3-5

Figure 3-9

Figure 3-10

Figure 3-11 Figure 3-12

Figure 3-13 Figure 3-14

Figure 3-15

Figure 3-16 Figure 3-17 Figure 3-18

Figure 4-1 Figure 4-2 Figure 4-3 Figure 44 Race Drivin?

Steering Wheel Submenu Screen, Send Force Screen Shifter Screen... Link Connector Test Screen .. ROM Checksums Screen ... ADSP Board Tests Screen, ADSP ROM Checksums Tests Screen 2-19 2-19 Sound Board Tests Screen... Sound Board Sound Wave ROM Checksums Screen. DSK Board Test Screen DIP Switch and LED Locations on the Main PCB....... i

Removing and Installing the Dashboard... 7 Steering Wheel | Has No Feedback and You Have Tried the Ser Controls Screens Steering Wheel is to One Side and You Have Tried the Set Controls Screens... Steering Wheel is Jerky and You Have ‘tried the Set Controls Screens Maintaining the Steering Whee! Maintaining the Key Switch Assembly... = Chuch, Seat, or Gas Pedal is? Not Working or Working Erratically and You Have Tried the Set Contrals Screens os Maintaining the Clutch and Brake. Assembly... Brake is ‘Not Working or Working, Erratically and You Have Tried the Se? Controfs Screens ..... Rewinding the Gas Pedal Pulley Cable .. Maintaining, the ‘Gas Pedal Shifter is Not Working or Working Ereatically and You Have Already ‘Tried the Set Controls Screens... Maintaining the Shifter .. - Seat is Not Locked ‘When ii Should Be and You Have Already Tried the Set Controls Screens .... — Seat is Locked When it Should Not Be and You Have Already ‘Tried the Set Controls Screens . Maintaining die Seat Assembly Removing the Video Display Disassembling the PC Board Stack...

Cabinet-Mounted Assemblies Seat Assembh Dashboard Assembly. Key Switch Assembly

Page 7

Race Pelvin’

Figure 4-5 Steering Assembly. Figure 4-6 Shifter Assembly ... Figure 4-7 Cluch and Brake Pedal Assembly Figure 4-8 Gas Pedal Assembly... Figure 4-9 — Goin Acceptors, Inc. Coin Door

Figure 4-10 Power Supply Assembly. Figure 4-11 Hard Drivin’ Main PCB Assembly Figure 4-12 APU PCB Assembly .. Figure 4-13 Shifter PCB Assembly . Figure 4-14 Brake PCB Assembly

List of Tables Table 1-1 Simulator Specifications.

Table 2-1 ising the Self-Test Screens and Diagnostic: Table 2-2 Coin Option Settings Table 2-3. Ail Screens Appearing Self-Test... Table 24 = Game Option Settings Table 2-5 When to Use the Special Function items... Table 2-6 LED Stams Table 2-7 Using the DIP Switches Table 3-1 Fable 3-2 Table 3-3

Table 34

Table 3-5 Table 3-6 Table 3-7 Maintenance and Inspection Items Froubteshooting Ail Controis Voltage Inputs and est Points on the Simulator PCBs... Troubleshooting the Steering Assembly ... 3-5 Troubleshooting, y Switc! 321 Troubleshooting the Clutch Pedal ..... 3-13 Troubleshooting the Brake Pedal ...... 3-17

Table 3-8

‘Table 3-9

Table 3-10 Table 3-11 ‘Table 3-12 Troubleshooting the Gus Pedal Assembly .. ‘Troubleshooting the SI Assembly Troubles: iB . ‘Troubleshooting the Video Display ... ‘froubleshooting the Speakers... 3°38 + BOE

Page 8

Race Drivin’

Safety Summary

The following safety precautions apply to ail game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game undE & has been inspected and properly grounded, ‘This game should only be plugged into a grounded threewire outlet, if you have only 2 two-wire outlet, we recommend you hire a licensed electrician to mstali a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, cheek chat the grounding wire is firmly secured to the inside of the contro! panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game's power supply can accept the AC line voltage in your location. The fine voltage requirements are listed in the first chapter of this manual, Disconnect Power During Repaies. ‘Io avoid electrical shock, disconnect the game from the AC power before removing of repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shack. High voltages continue to exist even after power is discormected in the display circuitry and the cathode-ray cube (CRT), Do not touch the iaternal pacts of the display with your hands or with metal objects! Always charge the high voltage from the CRT before servicing it. Do this after you dis~ connect it from the power source, First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground, Then momentarily touch the free end of the grounded jumper wire to dre CRT anode by slicing the wire under the anode cap. Wait tva minutes and do this again. Use Only Atari Parts, To maintain the safety of your Atari game, use only Atari parts when you repair it, Using non-Atari parts or modifying the game circuitry may be cangerous, and could injure = you and your players.

vi Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from dye implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Property Attach All Connectors, Make sure that the connectors on each printed circuit board (PCB) are properly plugged in, The connectors are keyed to fit only one way. If they de not slip on easily, do not force them. if you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 30 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard, Check the product identifica tion tabef on your machine for the line frequency required. ABOUT NOTES, CAUTIONS, AND WARNINGS tn Atari publications, notes, cautions and warnings have the following meaning:
NOTE -~ A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atad printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to Failure of following instructions.
WARNING — Players and/or technicians can be killed or injured if structions are not followed.
Page 9

CHAPTER i

Set-Up

HOW TO USE THIS MANUAL

This manual is written for operators and ser-

vice personnel. It provides information for

setting: up, driving, testing, and maintaining

@ Chapter i contains set-up and simulator driving inforyour Race Drivin’™ simulator.

mation. i Chapter 2 contains self-test procedures and additional diagnostic tests. The self-test is important in the Race Drivin’ simulator, You can troubleshoot the PC boards,

main circuits, and controls using the more than 60 screens in the self-test. You should regularly test the boards and controls with the selFtest to keep your simulator in peak condition and at top earnings. i Chapter 3 contains the preventive maintenance schedule for the simulator and the repair procedures, flowcharts, and troubleshooting tables for each control. If you have problems with your simulator, use this chapter to troubleshoot and to repair it, Be sure to perform the preventive maintenance tasks to keep your simulator in good condition. li Chapter 4 contains the illustrated parts lists. @ ® @

SBSSSHASSSSSSSSSVS

Page 10

Sel-Lp

: Operating the Simulator ‘Yo operate your simulator for maximum income, make sure your players know that the simulator is designed to be driven like a real car. You should regularly do the automated self-test and check the controls with the Control Inputs screen in the self-test. By using the seiftest regularly, you can find and fix problems immediately. This fets you keep your simulator in top conclition.

NOTE if you are installing a new printed-circuit (PC) board or a controf in your simutator, go through the Set Controls screen in the self-test. This is explained in Chapter 2. if you turn on your simulator and you see a screen that says Initialize Pot inputs ir stead of the attraction screens, then reset the controls by following the instructions on the screens thal appear.

Inspecting the Simulator

WARNING To avoid electrical shock, do not plug in the cabinet until it has been property inspecied and set up for the fine voltage in your area.

This cabinet should be connected to a grounded threewire outlet only. If you have only two-wire outlets, we recommend that you hire a licensed efectrician to instait grounded outers. Players can receive an electrical shock if the cabinet is not properly grounded. Inspect your Race Drivin’ simulator carefully to ensure that the simulator is complete and was delivered to you in good condition. Inspect the cabinet and seat as foilows: i. Examine the exterior of the cabinet for dents, chips, or broken parts.

  • Open the lower service door and the smal! top service panel. (Leave this top panel open so you can install the attraction sign.) Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a, Check that all plug-in connectors on the cabinet harnesses are firmly plugged in. Do not force connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed connector can damage a printed-circuit board (PCB). This will void your warranty. Race Drivin’

Table 1-1 Simulator Specifications Characteristic “Specification Power Consumption 635 W maximum Line Fuse Rating 7 Amps * Line Vohage 102 to 132 VAC Temperance 5° to 3B°.G G7? w 100° FD

HumidityNot to exceed 95% relative|
Widih34 1/2 in, (St em)1

Depth (seat pushed in) 62 1/2 in, (160 em.) |

HeightT7 in, (97 cmi
Weight730 Ibs, (341 kg.):

b. Ensure that alt plog-in integrated circuits on each PCB are firmly plugged into their sockets. ¢, Inspect the power cord for any cuts or dents in the insulation. d. Inspect the power supply, Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected, e, Inspect other sub-assembiies, such as the video display, controls, printed-circuit boards (PCBs), and speakers, Make sure that they are mounted securely and that the ground wires are connected.

Installing the Attraction Sign Assembly

The attraction sign assembly is shipped uninstalled with the simulator. Mount the sign on the back of the cabinet as shown in Figure 1-1. ‘The hardware for assembling the sign and for maunting it is shipped in the cash box, This hardware consists of ten 1/420 button-head screws 2 inches long with black washers.

  • Lay the atraction sign face down on a clean surface where it will not be scratched.
  • Lay the H-shaped attraction frame on top of the sign, Put the short ends of the H on top of the sign. The hamess connection in the leg should face
  • the sign. Attach the harness from the sign to the hamess in the feg. Push the extra wires inside the leg of the attraction frame.
  • Install six screws and washers through the attraction Frame and into the attraction sign. Tighten the screws.
Page 11

Race Privin'

Figure 1-1 Attraction Sign Installation

Now install the attraction sign assembly on the hack of the simulator, You need the other four screws and flat washers,

  • Open the small top rear panel of the simulator if you have not done so already,
  • Connect the simulator barness to the harness in the left leg of the sign. Now push the extra wires back inside the simulator. Be careful thar the har ness does not jie on the motor amplifier assembly, mounted on the side of the cabinet. 6 Put the attraction sign against the cabinet, and line up the four holes in the legs with the four holes in the cabinet.
  • Puc the button-head screws and black washers into the legs, anc screw them into the threaded holes,

Adjusting the Glides

After you move the simulator into location, screw out the adjustable glides in the base to support it. Fhe Race Drivin’ simulator is heavy, and if you do nat put down the glides, the casters may be damaged. Before you move the simulator, retract the glides so they are not damaged. Set-Up

Centrol and Switch

Locations

Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet.

Volume Control The volume control is located behind the upper coin door,

Self-Test Switch The selFtest switch is located behind the upper coin door, See Chapter 2 for a complete description of the self-test,

Auxiliary Coin Switches An auxiliary coin switch is located on the component bracket behind the upper coin door. Use the auxiliary coin switch to give players coin credits. Coin Counter ‘The coin counter is located behind the upper coin door. The coin counter records the number of coins deposited, ic does nor count the credits given by the auxiliary coin switch,

Setting the Coin and Game Options

‘The Race Drivin' coin and game options are set in the self-test, Refer to Chapter 2 for the recommended set tings and the procedure for setting the options.

Simulator Systems

The Race Drivin' simuiator uses eight PCBs to give a realistic look and feel to the driving. These PCBs are the main PCB, the ADSP PCB, the motor amplifier PCB Gvithanvo motor amplifier driver PCBs), the shifter PCB, the brake PCB, the audio and power PCB (mounted on the power supply assembly), the sound PCB, and the DSK PCR, ‘These PCBs control simulator software, the video display, and the controls. The main PCB, which is the largest, holds the 68010, the GSP, and the microprocessor systems. The 68010 system contains program RAM und ROM. The GSP (Graphic Systems Processor) micropracessor system controis the video RAMs (VRAMs). The ADSP board, the sound board, and the DSK board are mounted with the main PCB. The motor amplifier PCB is mounted in a heatsink assembly located on the driver's left. It controls the steering wheel motor, The shifter PCB is located on the driver's right and controls the gear shifter effects. The brake PCB is located on

Page 12

Set-Up

the brake and clutch pedal assembly and controjs the braking effects,

Maximizing Earnings

For maximum earnings, cegularly maintain your Race Drivin’ simulator following the instructions in Table 3-1, in Chapter 3. When you set up the simulator and when you collect money, perform the automated self-test and check the controls with the Gortro! inputs screen in the self-test,

Simulator Driving

This section describes the features and driving of the Race Drivin’ simulator.

Introduction Race Drivin’ includes all of the innovative game features that made Hard Drivin’ the industry's first true driving simulation game, plus many more new features, Race Orivia!

The autocross track witha built-in pace car provides feedback to hone competitive driving skills. The yeetor-drawn pace car is actually a recorded view of the player's best lap. Buddy Race — ‘Two-player sequential race in which the computer records the performance of player one, and player two races head-to-head against the first player and the clock. Linked Race Install a simple cable between two simulator cabinets, adjust game options, and the buddy race becomes a true head-to-head competition. Contact your Atari Discriburor for details and software availability. Select a Car Players can select from several different sports cars to suit the race track chosen. The Race Drivin’ cars are modeled after the performance features of several well-known sports cars. Each car has its own handling characteristics of off-the-line quickness, top speed, and cornering. In addition to all of the innovations aimed at the playef, Atari has also included many improvements that will be appreciated by the oper New Features ator, Race Drivin’ includes improved Handling — Faster mi- new materials for the croprocessor shifter boot and and more ef- electromechanficient soft- . ical parts. ware code ets S 7 There is provides a XN i also imnow im- proved perceptible servicelag time he- ability tween contro! input and screen 2 a ae | for magraphic response. Race Drivin’ feels even ea a jor commore like a real car! New Tracks — The Super Stunt track will challenge even the best Hard Drivin’ stunt racers, New tests of skill include a corkscrew loop, a jump loop, and 2 Fulf pipe. ponents such as the steering motor and pedal assemblics. Litle touches such as easier access to the cash box and servicing of the key start switch have been designed into the new cabinet,

Page 13

CHAPTER 2

Self-Test

‘The Race Drivin’ simutator is 2 complex machine. To keep it at peak efficiency and maximum earnings, you should regularly check the contrals, RAMs, ROMs, PCBs, and microprocessor systems. You can check all of these when you switch on the self-test. Also in the self-test you can check the video display, the statistics, and set the internal clock. IF you cannot use the self-test because the screen is dark, you can use a DIP switch on the main PCB to find the source of the problem, If you are having electronic problems, you can check the state of various signals with the LEDs on the main PCB. You should regularly check the following screens and information, We recommend you check these when you first set up the simulator, each time you collect money, o¢ when the simulator is not working correctly, M@ Use the automated self-test, which begins automatically when you turn on the self-test to test the program RAMs and ROMs, the video RAMs, color RAMs, the DSK PCB, the ADSP PCB, and the sound PCB. The test takes about 3 minutes to run. M Check the Control inputs screen, which you choose from the Tes? Menu screen. This shows the voltage input te the main PCB from the Stecring wheel, brake pedal, gas pedal, clutch pedal, seat, and shifter. With this information you can easily check how the controls are working.

NOTE if the control inputs are wrong, your earn~ ings may drop, since the realistic driving feet is fost.

@ Check the Statistics, Histogram, and Games Played by: Day and Hour screens which show the statistical information about how and when your simulator is played. Table 2-1 shows you what tests and screens to use at different times and for differeat problems. ® ® ® ®

Page 14

SelETest

Entering and Exiting the Self-Test

You enter and exit the automated self-test procedure by turning the self-test switch on or off. The switch is jocated at the back of the upper coin compartment. You mn the tests with the door open so that you can press the right and left coin switches to move up and down the ments, The self-test consists of: A five-minute automated self-test of the ROM, RAM, the microprocessor, and the PC boards WA Test menu from which you can mn specific tests in the event that you receive error messages If you are running a specific test and turn off the self- Ruce Drlvin?

tast switch to exit, you may need to proceed through all the screens in the submenu and return to the Test menu before you retum to the attract mode,

Automated Self-Test

When you enter the self-test, the simulator automatically tests the program ROM and RAM, the video RAM, the color RAM, the DSK PCB, the ADSP PCB, and the sound PCB.

NOTE if you do not see anything on the video display screen, you may have a video display problem or a simulator system problem. See DIP Switches at the end of this chapter to diagnose Ihe problem.

Table 2-1 Using the Self-Test Screens and Diagnostics

Problem or Type Explanation

as you enter the self-test.

plained at the end of this chapter

Electronics Problems . Do the automated self-test.

Game Clock

Cannot Enter the Self-Test the chapter. When you switch on the self-test, the automated selFtest Is performed, This tests the program RAM and ROM and the PCBs, You can skip the self-test by turning and Holding.the key as soan If you cannot run the self-test at all, use the DIP switches (0 diagnose the problem. These are ex- :

Appears after the automated selFiest. Select tests and information on this screen.

|, Make sure the options on the Operator Screens are set correctly for your location, or sel 10 the

FF uhat does not cortect the problem, go to the Control Inputs screen and sce if the input fom | i . Go to Chapter 3 and check the troubleshooting table and maintenance information forthat i

. Hf the shifter, brake, clutch, or seat porentiometer is broken and you cannot fix it immediately, but still want to operate the game, tum off the control circuit in the Disable Broken Controls ‘fest Menu Regular Maintenance Regularly do the following: 3, Do the automated self-test. 2, Check the Operstor Screens.

  • Go to the Control Inputsscreen to test the controls, Game SerUp When you first set up your game, do the following: I. Do the automated self-test.

defaults. 3, Go to the Control Inputs screwn (© test the controls.

  • Set the clock, if necessary, using the Set Time screen. Control Problem 1, Do the Set Controls screens. z the contol changes as you use the convol. 3. H coaral.

screen, Video Display Problem 1. Tey the Monitor Test Patterns screens, “2 . If you cannot go ime the self-test or the screen is dark, use the DIP switch diagnostics.

i :

  • Ghoose the Special Functions sereen that applies to your problems: the GSR, program ROM, ADSP PC beard, sound PC board, or DSK PC board test. Use the Set Time screen to set the intemal game clock, This time’is used in the statistics screen that shows games played by day and tlme and in the schedule for clearing the high score table. Use the DIP switches and the LEDs to diagnose the problem. These are explained at the end of |
Page 15

Race Drivin”

The automated testing takes about five minutes. The results appear on the screen. Messages in red alert you To a problem. You can nun further testing from the Test menu, If you do not want to wait for the systems and PCBs to be tested, you can skip these tests by turning the ignition key while in the program ROM and RAM screen, Figure 2-1. (IF the self-test proceeds beyond this screen, it will min its course.) If you want to exit to the attract mode, just turn the self-test switch off,

Program ROM and

RAM Test

When you enter self-test, the simulator tests the program ROM and RAM. The screen in Figure 2-1 shows the results of 2 program ROM and RAM test.

BAD PROGRAM ROM IS SLANK BOX ¥ x wey uo Tt 2900 = 3 © ato s a Ld ROMS AY 2008 AND 210R CONTAIN THE SELF-TEST PROGRAM

PROGRAM HAM OK

HOLD KEY TO BYPASS SELF-TEST

Figure 2-1 Program ROM and RAM Fest Screen

The top of the screen shows the ROM tesr result. The numbers on the left and the letters on the top of the screen show the locations of the ROMs on the main PCB. If a white box appears, then the ROM there is good. If an empty box appears (as shown at 200U and 210U), then the ROM there is bad. If nothing appears, then nothing was tested there. The RAMs are tested after the ROMs. If the RAMs have no errors, then you see the message Program RAM ‘OK, if the test finds an error, then you see Bad Program RAM At with the bad RAM location listed, This screen disappears after a few seconds and the self-test continues. However, the screen with the re sults of the complete self-test, shown in Figure 2-2, shows the message Bad Program ROM (or Bad Program RAM) if it found an error in the program ROMs or RAMs. Self-Test

Microprocessor and

Board Tests

After checking the program RAM and ROM, the automated self-test checks the simulator's microprocessor and PC boards. It tests the video RAM and color RAM in the GSP microprocessor system, the DSK board, the ADSP board, and the sound board, ‘fhe test takes four to five minutes. You see the screen in Figure 2-2 when the test finishes.

BAD PROGRAM ROM PROGRAM RAM OK GSP YRAM OK—SIMPLE TEST GSP COLOR Aam OK DSK SOARD OK ADSP BOARD OK SOUND SOARD TEST OK SOUND WAVE ROMS OK STEERING WHEEL MOTOR TEST OK, SIMPLE TEST.

TURN KEY TO SELECT FEST MENU

Figure 2-2 Microprocessor and Board Tests Screen

if the system or board is good, OX follows the test name. If it is bad, the word Bad precedes the name of the board or system (except for the ADSP board test, which gives more information). If you have a bad system or board, then choose Special Functions from the Fest menu, choose the appropriate system or board tests from the Special Functions menu, and read the description of the rests in this chapter. Here is a brief description of each microprocessor and board test performed during the automated self-test. PROGRAM ROM: Described above, PROGRAM RAM: Described above. GSP VRAM: Uses the Simple GSP VRAM Test. (Described in the section Main Board GSP Tests) GSP COLOR RAM: Uses the GSP Color RAM ‘Test. (Described in the section Main Board GSP Tests.) DSK Board: Tests two ASIC systems, the DSK Program RAM, the DSK ZeroPower RAM, and the DSK Program ROM. ‘These tests are described in the section DSK Board Tests, ADSP Board: Tests the ADSP board memory and the ADSP-2160. Most of the error messages are self-explanatory, (Does Not Respond generally indicates a missing board.) Sound Board: Tests the sound program ROM and

Page 16

Sel Test

RAM, the sound hoard communications ROM and the 32016 ROM. Sound Wave ROMS: Tests the ROMs that have the sound waveform data. If any are bad, the message Bad Sound Wave ROMs appears on the screen, Steering Wheel Motor Fest: Performs a simple test of the steering wheel system.

Test Menu Screens

After the microprocessor and board test is Finished or you bypass it, turn the key to procced to the Test menu. The Test menu screens let you conduct specific troubleshoating in the event of problems. ‘Tum the key once to see a screen that explains how to select from the Test menu, shown in Figure 2-3. Turn the key again to see the Test menu, shown in Figure 2-4. As the screen shown in Figure 2-3 explains, you use the right and left cain switches and the igaition key to

USING THE TEST MENU:

PRESS LEFT COIN SWITCH TO MOVE UP OF TO INCREMENT PRESS RIGHT CORN SWITCH TO MOVE DOWN OR TO BECREMENT TURN KEY TO CHOOSE FTEM OR TO RETURN

Figure 2-5 Instructions for Test Menu Screen

TEST MENU OPERATOR SCREENS SET CONTROLS: CONTROL INPUTS: MONITOR TEST PATTERNS: SET TiME DISABLE BROKEN CONTROLS SPECIAL FUNCTIONS

RACE DRIVIN' VERSION 8.7 COPYRIGHT ATARI GAHES 1948; 1989, 1590

Br06:24 AM SULY 29, 1990

Figure 2-4 Test Menu Screen Race Davin’

make a selection from the Test menu. Pressing the fight or left coin switch on the back of the upper coin door moves you up or down the menu. When the option you want is white, turn the ignition key to select it. The submenus for the specific tests work the same way. The Test menu, shown in Figure 2-4, is the most important screen in the self-test. Use this screen to choose specific tests 0 pinpoint problems and to set the game options. Table 2-4 shows ail the tests that are available from the Test menu.

Operator Screens

Choose Operator Screens from the menu by pressing the right or left coin switch until this item is white, then turn the ignition key ro select it. If you are in the operator screens and want to go {a the attract mode, first turn the key to go through the remaining operator screens. When you return to the Test menu, turn off the self-test switch. The Operator Screens ler you set game options and monitor the use of the simulator. The choices on the Operator Screens submenu are: Bf Coin Options Hf Link Options MH Game Options BE Statistics BE Histograms of Game Times B Error Count Ml Games Played by Day and Hour

Coin Options

The first operator screen, Coin Options, fets you reset the coin credits (see Figure 2-5). To reset the coin options: @ Move up or down the list by pressing the right or

Toln Gations Coin Made Seolns 4 ore Right Mech tuftiplior fT enin counts 85 7 coin Left tech Mutlipiler ‘t coin counts as t coin Bonus Adder No Bonus Adder

Hit LEFTAIGHT coin switches ta move UP/DOWN Hold ABORT ang hit coin switches te eyete through chairs Hold down ABORT and turn kay to restore original setting Just tunt key to save this setting and exit

Figure 2-5 Coin Options Screen

Page 17

Race Drivin’

left cain switch, A biue box indicates which item is selected.

M@ Press the Abort buuon and either coin switch 10 sesoll through the settings until you see the one you want

@ 7o return to the original settings, press the Abort button and turn the ignition key. @ When duough, turn the key to exit the screen. The defauit setting of each option is green. The available seitings are listed in Table 2-2.

Table 2-2 Coin Option Settings Option Available Settings } Coln Mode 1 coin/1 credit 2 coins/1 credit i 3 coing/1 credit # i 4 coins/i credit H

  • coin counts as 1 cain i colm counts as 4 coins 1 coin counts as 5 coins J coin counts as 6 coins Right Mech Multiplier

i coin counts as 1 coin | I coin counts as 2 coins

No bonus adder H 2 coins give J extra coin 5 coins give 1 extra coin Left Mech Multiplier

Bonus Adder

4 coins give 1 extn coin 4c give 2 extra coins i 4 coins give 1 extra coin i Free Play H © Manufacturer's recommended settings i

The Coin Options are as follows: @ Coin Mode is the number of coins requirect for one eredit,

BM Rigdt Mech Muitiplier is the number of coins each coin counts as in the right coin mechanism. WM eft Mech Multiplier is the number of coins each coin counts as in the left coin mechanism.

@ Bonus Adder lets you choose bonus coins, no bonus, or free play.

Game Difficulty

The game difficulty of each track and the difficulty of the drone car for each wack can be set with this screen {Figure 2-6). in addition to settings of easy, medium, hard and very hard, custom tuning is provided, In the Custom setting, you can choose the actual amount of time a driver is given. You can select different times for each individual lap in this option. The actual times for easy, medium, hard, and very Self-Test

GAME DIFFICULTY

ORIGINAL TRACK DIFFICULTY MEDWUM BAONE ON ORIGINAL TRACK MEDIUM AUTOCROSS TAACK DIFFICULTY MEDIUM DRONE ON AUTOCAOSS TRACK MEDIUA SUPER START TRACK DIFFICULTY MEDIUM DRONE ON SUPER START TRACK MEDIUM

FREE GAME ON MULTLPLAYER GAME

YES

Figure 2-6 Game Difficuity

hard game difficulty settings are also shown in the custom settings. For example, if you have chosen the medium setting in Game Difficulty, then the custom screen appears as shown in Figure 2-7.

NOTE Always use the preset Game Difficulty Settings belore you use the settings of the Custom game options,

To move and choose in dis screen, do the following: M1 To move up or down the list, press the right or left coin switch.

M@ To change a setting, press the abort button and either coin switch.

B To return to the setting that was originally on the screen, press the abort button and tum the key, Mi To exit the screen, tum the key. You can change an option when it is inside the blue

XXXX TRACK TIMING CUSTOM OPTIONS TRITIAL TIME $0 MEDIUM FIRST EXTENDED FEME 44 MEDIUM: SEGOND EXTENDED TIME 44 MERIUM: EXTENDED T:ME AFTER SECOND 45 MEDIUM HIT LEFTAIGHT COIN SYETCHES TO MOVE UP/DOWN HOLD DOWN ABORT AND YURU KEY 10 RESTORE ORIGINAL SETTING JUST TURN KEY TO SAVE THIS SETTING AHO EXIT

Figure 2-7 Custom Game Options Screen

Page 18

SelfTest Race Trivin’

fable 2-3 All Screens Appearing in the Self-Test

Screen Use

Antomated Self Test Program RAM and ROM Automated Self-Test Results

Test Ment Screens Instructions for fest Menu Test Menu

Operator Screens Coin Options Game Difficuhy Track Timing Game Optians Statistics Histograms: Error Count Games Played by Day and Hour Set Controls Initialize Pot Inputs Initialize Steering Limits initialize Shifter Limits Initialize Seat Limits Initialize Force Brake

Control Inputs Monitor Test Patterns Color Bars Monitor Adjust Moniter Brighiness Grey Scale BAY Dots BAS Grid Diagonal Lines full Screen Grey Full Screen White Full Screen Red. Full Screen Green Full Sereen Blue Monitor High Vohage Test Scrolling Test Set Clock

Disable Broken Controls Tests the program RAM und ROM Shows results of the program RAM and ROM, VRAM, color RAM, MSP DRAM, ADSP PCR, and sound PCB rests.

Taformation sbont using the test menu. List of availabh: tests and information you can choose.

Sets the coin options. Sets teack and drone ditficuky. Use preset game: options first. Sels the game options, controls the high scare table and steering in the auract made. Shows game statistics. Shows game histograms, and aumber of games by length of play. Shows the error count from the PC boards. Used by the factory for debugging. The simulator clock must be set correctly to get maximum use from this scteen.

Lise if yout are having any controt problems or replace or repair & control or a PCB. Initializes all the simulator potentiometers. Sets the steering limits, Sets the shifter limits, Sets the seat movement limits. Sets the limit on the force on the brake.

Check this screen reguiariy to make sure your controls are operating correctly. Use these screens to check the performance of your video display. Shows the viceo display colors. Used for the monitor setup. Shows ihe brightness adjustment. Shows the grey scale of the video display. Shows convergence and focus of the video display. Shows convergence and focus of the video display. Shows linearity of the video display. Shows the color purity of the video display. Shows the color purity of the video display. Shows the color purity of the video display. Shows the color purity of the video display. Shows the color purity of the video display. . Checks the regulation of the high voltage to the video display. Checks the scrolling mechanism of the GSP microprocessor. Set the time so that you can get maximum usc from the Games Played By Day and Hour screen and so that the high score table reset occurs at the right time. If you cannot repair a broken shifter, brake, clutch or seat potentiometer immediately, you can disable that controf's circuil so you can continue to operate the game. Repair the broken control as soon as possible. Use this screen only as a temporary measure,

Page 19

Race Drivin’ Self-Test

Table 2-3 All Screens Appearing in the Self-Test, Continued

Special Functions Use this screen for tests of the controls, PCBs, and microprocessars. Main Board GSP Tests Use this screen if you have « VRAM failure in the automated self-test. VRAM Simple Fess Checks for bad VRAMs in the GSP microprocessor system. VRAM Verify Test Tests aii the VRAM GSP mentory, VRAM Complete Test Completely tests all VRAM. Color RAM Tests the color RAM. RAM Shift Register Test Checks the VRAM shift register.

Main Soard Controis Shows much the same information as the Control fiputs screen, but has addidonal tests for the steering wheel, shifter, and line voltage calibration. Pots: 8 Bit Shows the gas pedal, clurch pedal, seat movement, shifter movement, steeding wheel movenient, line vollage anc the shifter force input to the main PCB. Pots: 12 Bit Shaws the st¢ering wheel mavement and the brake force input (@ the maln PCB. Steering Wheel Use if the swering wheel does not work. See the steering wheel flow charts In Chapter 3 far information about their use. Send Force Use this test as directed in the fowchant in Chapter 3. Sine Wave Sends 2 sine wave farce 10 the motor amplifier PCB, Square Wave Sends a square wave force ta the motor amplifter PCB, Triangle Wave Use this test as directed ia the Itowchast In Chapter 3. Closed Loop Test Sends a force to the motor amplifier PCB simulating a simple spring. Line Voluge Calibrates the line voltage display in the self-test. Calibration Opto Test For factory use only. Life Test For factory use only. Shifter ‘Use this screen if the shifter docs not work comectly. Link Connector ‘Use this sercen if the game fink docs not work correctly.

Main Board ROM Checksums ‘Use this test if the progcim ROMs fail the automated self-test.

Main Board 2RAM Tests Check the ZRAMS. Use this if all the controls are operating erratically or the stuisics are not kepe correctly, ADSP Board tests ADSP RAM -TESTED BY 68020. Use dhis test if the ADSP board fails the automated self-test APSP PROGRAM MEMORY TEST .2100. ‘The 2100 runs « standard, complete test on its own program memory. ADSP DATA MEMORY TEST 2100. The 2100 runs 2 standard, complete test on its own dats memory. 210 Test Tests the response of the 2100 integrated circuit on the ADSP PCB. IRQ Test Tests if the ADSP system can genenite IRQs. ROM Checksums Tests the griphics ROMs on the ADSP PCB, AOSP Special Functions Performs hardware diagnasis and oscilloscope test loops for use by a repair technician.

Sound Board Tests Use these tests if the sound board faits the automated self-test. Sound Board Self-Test Tests the sound program RAM and ROM, COMRAM and the 320 RAM, Play Sounds Choose and hear game sounds. Sound Board ROM Checksums Tests the sound PCB ROMs. Sound Board Program RAMs Tests the sound PCB prograra RAMS. Sound Board Program ROMs Tests the sound PCB program ROMs. COMRAM Tests the sound PCB communication ROM, 320 RAM. Tests Ube sound PCB 32010 program RAM.

Page 20

Self-Test

box. The default setting of each option is green. The other settings are blu¢ when the option is selected. {The other settings are white when the option is nor selected.) The custom game options are explained below, Mf Initial Time is the amount of time always given for one driving session. @ First Exiended Time is the amount of time given if the driver crosses the finish line before the initial dime is up. @ Second Extended Time is the amount of time given if the driver crosses the finish Hine before the time is up on his secon lap. @ Extended Tine After Second is the amount of time given when the driver crosses the finish line before the time is up after the first two laps.

Game Options

Use the Game Options screen to set the game difficulty and the operator options as explained below, The screen is shown in Figure 2-8, You operate this screen the same as Coin Options. Press the coin switch to select an option, and press Abort and 3 coin switch to scroll to the setting you want, Turn the key to save the settings and exit. A list of the available settings is shown in Table 2-4. The Game Options available on this screen set the following: W Game Difficulty sets the game difficulty for the drivers. The settings are shown in Table 2-4. The custom setting lets you choose the actual aniount of time the players receive. We suggest you use the

Table 2-4 Game Option Settings

OptionAvailable Settings|
Champ LapEasyMedium @|

Qualification Hard Very Hard i

i

Steering DuringoneOF{

sMtract Mode

Steering Wheel ForceVery LightLight

Medium ¢ Suff High Score Name Censor Easygoing # — Strict Clear High Score Table Don't Clear Clear Now Clear Every Week Clear Every 2 Weeks ¢ Signs and Gauges Miles per Hour Kilometers per Hour Game Type Available Soon Race Drivin’

GAME OPTIONS CHAMP LAP QUALIFICATION STEERING DURING ATTRACT MODE STEERING WHEEL FOACE MEDIUM (GH! BOONE MANE CENEOR EASYGOI CLEAR SIGH SCOME TABLE CLEAR EVERY 2 WEEKS SIGNS AND GAUGES MILES PER HOUR REVEASE GEAR DISABLED (MUST PIN SHIFTER} E NOT LINKED

HIT CEFT/AIQHT COIN SHITOHES TO MOVE UP/DOWN HOLD DOWN ABOAT ANO TURN KEY TO RESTORE OhIGINAL SETTING OUST TURM HEY TO SAVE TRIS SETTING AND EXIT

Figure 2-8 Game Options Screen

preset factory setting (easy, medium, hard, and very hard), nor the custom setting. Bl Champ Lap Qualification sets the difficulty of qualifying for the championship lap. I Steering During Attract Mode allows you turn the movement of the steering wheef on or off while the simulator is in the attract mode, Steering Wheel Force is the amount of force exerted by the steering assembly motor on the stéering wheel. Ml High Score Name Censor controls a program to censor names entered on the high score table. The program deletes letters in passibly objectionable words in the high score table. Ml Clear High Score Table clears the nigh score table at the time chosen. You can choose not to clear the table, clear it now, clear every week, or clear every two weeks. If you choose clear every week or clear every ovo weeks, the table is cleared when the simulator is turned on after Wednesday midnight every week of every second week. Be sure your simulator clock is set correctly so the table clears at the right time. W Signs and Gauges allows you to choose whether the signs and gauges are displayed in kilometers or miles.

Statistics

The statistics screen is shown in Figure 2-9. The statistics are collected from the last time the statistics screen was cleared. Write this information on the statistics sheet in the back of this manual to help you maximize your profit. ‘Yo move to the next screen, just turn the key. To clear the staUistics, press and hold the abort button and tum

Page 21

Race Deivin’

the key at the same time. The statistics the simulator collects are explained below,

& Left Coins shows the number of coins counted in the left coin mechanism, @ Right Coins shows the number of coins counted in the right coin mechanism. @ Aux Coins shows the number of times the auxiliary coin switch (inside the coin door) is pressed, Wf idle Mins shows the number of minutes the simulator has been idle.

Active Mins shows the number of minutes the simu- Jator has been played, @ Error Count shows the number of errors counted in the erasable memory. If you have more than 75, check the ZRAMs with the self-test. Your simulator may need service.

Mi Total Games shows the number of unique games played.

Bottom Half of Screen Por che remaining statistics (except for the five entries at the very bottom of the screen), the three numbers after each entry represent, from left to right: first — original tmck at the beginning, second — autocross track, ane. thie — super stunt track.

Wi Laps hy Track is numbers of taps, completed or nor, on

each track.

No X Games by Track is the number of times the rivers did not get extended games on either track, [fF the numbers are very high, then the game difficulty may be too hard.

BR 2, 2, and 3+ X Play Games by Track is the number of additional laps given to drivers if they complete the track before the time allouted. These additional laps do not need to be completed to be counted.

@ Champ Laps is the number of times drivers qualified to

tace a championship lap, @ 2 Player Games éy Track is the number of games played with nwo players, MM 2 Player Time by Trackis the average time of all games played with two players. B Free Games by Track is the number of free games played on each track. @ Total Games by Track shows the number of unique games for each track, regardless of how many additional laps each driver received. Mi Tota! Time by Track shows the total time of ail games for each track, Self-Test

ra

Active Mint Auto Games: Error Court: Total Games: hepa by Feacke Wo X Gamas ey Track: 4X Play Games ny Trae! 2X Play Grmos De K Pisy Games by 7 Shamp Lugs by Track: 2 Flayar Gamos by Tre! 2 Playee Tinto hy Troe Free Games by Feat Total Games by Frack Fetal Time by Track: Avg thao by Trnek fee): Games Per Car RplAborts 00 [ eynaeepensaes eecnesnoe eveeasosngs09 cy o @ cs

a a

a o < Rel Secs 000

Figure 2-9 Statistics Screen

Wi Aug Time by Track {sec} shows the average coral ime of ail games for each track.

Ml Games by Car shows the number of games played with each type of car,

Mf Inst Rois is the worl number of instant replays. Mf Ap! Abortis the times the drivers pressed the abort but- Ton { cut the instant replay short. Mi Roi Secs is the coul seconds the simulator is in the replay mode,

M Total Credits is catculated by multiplying the coins by the credit setting you chose in Coin Mode. BM Avg Time Per Credit is the average amount of time in seconds that each credit gave.

Histogram

The histogram screen shows the length of driving time in seconds and the how many times the simulator was driven, The screen is shown in Figure 2-10, Write these numbers oa the statistics sheet in the back of this manual to help you maximize your profit, To move to the next screen, turn the key. To clear the histograms, press and hold the abort button and mm the key at the same time.

Error Count

This screen shows the error couat on the PC boards. If you cail Atari Game Customer Service, the numbers on this screen may help Customer Service personnel troubleshoot your problem.

Page 22

Self-Fest

Games Played By Day and

Hour

This screen, illustrated in Figure 2-11, shows the aumber of games played every hour in each day, The information on this screen relies on the simulator clock being set correctly. (The clock time is shown on the bottom of the Test menu screen. If the time is incor rect, follow the insiructions in the Se? Clock section of this chapter to set the clock.) Write the simulator driving information on the statistics sheet in the back of this manual! to help you maximize your profit. ‘Yo clear the screen, press and hok! the abort button and turn the key at the same time,

Set Controls Screens

If you have problems with a contro! in the sinvulator, use the Sef Controls screens before doing any troubleshooting of repairs. These screens allow you to set the beginning and ending points of the contol input to the main PCB. Often, resetting these points will solve the problem you have, If resetting does not solve the problem, then check the Cotrof Mnputs screen, described below. If you repair a contri, chen when you put the control back in the simulator, go through the Sef.Controt screens. If you install a new board or a new control, you must go through the Sef Comtrof screens too. The first Se? Controls screen is shown in Figure 2-12.

NOTE If you take a control out of the simulator for repair or maintenance, you must gO through all the Set Controls screens after you replace it. f you do not, the simulator will not operate correctly.

After you chouse Set Controls, simply do what the screens say. You must reset al} the controls after you start the screens. ‘Che first screen initializes all poten- Hometers in the simufacor, (The steering wheel, shifter, seat, gas, and brake have potentiometers. > The next screens initialize the limits for the steering wheel, shifter, seat, and brake, The numbers on each screen are for factory use. Race Drivin"

Histogram of Game Times

Hold ABORT snd turn key to clear histogram ust turn koy for next screest

Figure 2-10 Histogram Screen

NOTE When you initialize the brake, the instructions say to "step firmly” on the brake, Do not stomp on the brake or gently press it. Either way sels the brake limits incorrectly and drivers will be frustrated when they use the brake.

Control Inputs Screen

Check this screen as part of your regular maintenance to be sure your controls are operating correctly. The Control Inputs screen is shown in Figure 2-13. This screen shows the voltage inputs from the control potentiometers to the A/D convener circuits on the main PC board, As you use a control, the line length on the screen changes, showing the change in the voltage input from the potentiometer. if the line jength does not change, you have a problem. If you have a problem, first go through the Set Gontrofs screens {0 see if that solves the problem. Check the results on the Control Inputs screen. If using the Set Controls screens does not solve the problem, check Chapter 3 for troubleshooting and repair information. The first control on the screen is the Steering Wheel. This line shows the movement of the steering wheel As you tum the steering wheel counterclockwise, the line should disappear. The second line is Brake Force which measures the force with which the brake is pushed, As you push harder and harder on the brake, its line should disap-

Page 23

Race Drivin’

Games Played by Diy and Hour. Man tue Wad. thu a Tue Wor Sat

3: 5: &

Bt S 49: Ml poseuns Hold ABORT iad turn koy to clear ible Gust burn key for telf Sst menu

Figure 2-11 Games Played by Day and Hour Screen

pear. In both of these lines, 0 Volts appears as no line or a short line on the screen, and 5 Volts appears as almost eight full lines on the screens. Below these two lines are the gas pedal, clutch pedal, seat movement, shifter (front to hack), shifter Geft to right), steering wheel, line voltage, and shifter force. {The steering wheel movement is checked with two lines.) As you use the controls, the lines should become longer and shorter. ff the line does not move, then see Chapter 3 for more information, (The line voltage varies at GO Hz. You cannot test the line vole age.) For these controls, 0 Volts input appears as no line or a short line on the screen and 5 Volts appears as a line halfway across the screen. At the bottom of the screen, you can check the left and right coin mechanism, the auxiliary coin switch behing the coin door, and the seat magnet. Use the

INITIALIZE POT INPUTS.

TAKE YOUR HANDS AND FEET OFF ALE CONTROLS THEN TURN KEY

Figure 2-12 First Set Controls Screen Self-Test

seat magnet test to determine whether the seat is focking as it should and if the magnet is good. Tf the seat has not been working correctly, but does tock in this test, the switch probably should be repaired or replaced. if the seat does sof lock, then your problem is probably the harness or the magnet.

Monitor Test

Patterns

Use this item to see the fourteen screens for checking the video display, the color RAMs, the GSP, which controls the video RAMs (VRAMS), and the video output. To move through the screens, press the coin switches. WW Color Bars screen shows these colors from left to fight: white, yellow, light blue, green, purple, red, blue, and grey. tf the colors are incorrect, see your video display manual for adjustment procedures, Wi Monitor Adjust is used to set up the monitor. Monitor Brightness checks the adjustment of the video display brightness. @ Grey Scale screen shows a white fine on the feft, and a grey scale showing black on the Jeft. BAY Dots screen can be used to check convergence and focus, @ B/W Grid screen, shows a black background and a white grid pattern to check convergence. The grid lines should be straight within 3.0 mm. If you need to adjust the convergence, see the video display manual included with the simulator. Mf Diagonal Lines screen can be used to check video display linearity. M@ Full Screen cotors test the color purity of the color

CONTROL INPUTS STEERING WHEEL

BRAKE FORCE

  • GAS EE ETH
  • SEAT SHIFTER F/B SHIFTER L/R WHEEL nen LINE VOLTS a SHIFT FORCE

LOO RGOIN AUXCOIN PRESS ABORT TO TEST SEAT LOCK

Figure 2-13 Control inputs Screen

2-11

Page 24

Self-Test

RAMs and the display. The test displays a grey, white, red, green, and then blue screen. Each sereen should be a rectangle of color, with no curing at the corners ancl no jines in the raster. If it does not, see your video display manual incluced with che simulator for adjustment procedures. Monitor High Voltage Test screens switch beween a white screen and a grey screen. If the high voltage to the display is regulated properly, the sides of the sercen will fluctuate about 3/4 inch from the white to the grey screen, Ml Scrofting Test sercen checks the scrolling mechanism in the GSP

Set Clock Screen

Choose this item if you want co set the clock, turn the clock on, or turn it off. The clock should be set correctly so the statistics on the operator screen Games Played by Day and Time will be right. The time on the clock also cetermines when the high score table is cleared. If you set the Clear High Score Table option in the Game Options screen to clear ev« ery week or every other week, then the high score table is cleared the first time the simulator is tumed on after Wednesday midnight. You may need to tuen on the clack if the simulator has a program crash. Turn off the clock only # you plan to store the simulator more than six months. (The clock has a lithium battery that should last more than five years in normal use.) ‘Fo turn off the clock, choose Clock Off fram the clack submenu, shown ia Figure 2-14, To turn on the clock, choose Start Clock from the menu. ia about two seconds, the clack starts. JF the clack is losing or gaining time, then use Clock Faster or Clock Slower to adjust the calibration of the clock. Choose the item you need from the menu by using ¢ither coin switch. Change the setting by qurning the key until you see the correct tine. The items on the clock menu are explained below. Exit returns you t the Test menu. i inc Hours changes the hour setting ahead. @ Inc Mouttes changes the minute setting ahead. lf inc Seconds changes the second setting ahead. @ fnc Day changes the day of the week (for example, Monday or Tuesday) setting ahead. BF Jae Month changes the month setting ahead. @ fnc ere changes the date setting ahead,

2-12 Race Drivin’

@ /nc Year changes the year setting ahead. @ Faster Clock changes the calibration setting ahead. Each increase in the calibration setting makes the clock nin about 5 seconds faster per month. M@ Clock Offturns the clock off. M@ Dec Hours changes the hour setting back. M@ Dec Minutes changes the minute seting back. @ Dec Seconds changes the second setting back. @ Dec Day changes the day of the week (for example, Monday or Tuesday) setting back. @ Dec Month changes the month setting back. Ml Dec Date changes the date setting back. Wl Dec Year changes the year setting back. § Slower Clock changes the calibration setting back. Each decrease in the calibration setting makes the clock run about 3 seconds slower per month.

@ Start Clock starts the clock.

Disable Broken Controls Screen

Use this screen, shown in Figure 2-15, if you have a broken shifter, brake pedal, clutch pedal, or seat potentiometer and cannot repair it immediately. Before you use this screen use the Sef Controfs screens and read the information gbout the control in Chapter 3. Disable these controls only as a temporary measure 30 you can continue to operate the simulator while waiting for parts. If you disable a control, the realistic driving fee] of that contro! is lost. Earnings could drop. When you disable a control, the control circuit is overridclen, and the simulator compensates for the loss of the control. If you have disabled a concrol, remember

£xit ING HOURS INC MINUTES INC SECONDS ING DAY INC MONTH INC DATE ING YEAR FASTER CLOCK CLOCK OFF DEC HOURS BEC MINUTES BEC SECONDS BEC DAY DEG MONTH DEC DATE DEC YEAR SLOWER CiocK START CLOCK

CALIBRATION: +000 SECS/MONTH 14:22:21 AM NOVEMBER 22, 1988 FRIDAY

Figure 2-14 Set Clock Screen

Page 25

Race Drivin’

to choose working after you repair it so the control works correctly.

Special Functions Screens

Use the items on this screen, shown in Figure 2-16, if a system or board Failed the program RAM and ROM test or the board and microprocessor test in the automated self-test, Also use this screen if you have problems with the steering wheel, the shifter, ar if the clock ser tings or the statistics are ernutic. A short summary of ‘when to use these items is shown in Table 2-5. ‘the Special Functions items are explained below. # Enctreturns you to the Test menu. @ Main Board GSP Tests should be used if you get the message Sad GSP VRAM or Bad GSP Colar RAM in the automated self-test. This screen has six tests you can use. Wl Main Board Controls gives you most of the same information as provided in the Control inputs screen Plus five steering wheet tests, a line voltage calibration screen, additional shifter tests, and a fink con- Gect test. (All controls are “main board” controls.) @ Main Board ROM Checksums should be used if you get the message Bad Program ROM in the automated self-test. This tests the program ROMs individuaily and shows the results on the screen. @ Main Board ZRAM Tests shouid be used if your controls settings are changing or erratic even though you used the Sef Controls screen. Also use these tests if you suspect the simulator is not keeping the statistics correctly. @ ADSP Board Tests should be used if you get any message other than -LDSP Board OK for the ADSP board test in the automated self-test. This screen has three tests and an ADSP ROM checksum test, it also has eight “scope loop” tests for factory use only since they require schematics and an oscilloscope. # Sound Board Tests should be used if you get the message Bad Sound Board in the automated selftest. However, many of the sound board tests are for factory use only since they require schematics and an oscilloscope. I DSK Board Tests should be used if you get the mes sage Bad DSK Board in the automated self-test. This Screen allows you to test the DSK ROMs, the DSK RAM, the DSK ZeroPower RAM (ZRAM), and the two ASIC subsystems, It also has a Special Functions screen for factory quality assurance. Self-test

DISABLE HROKEN CONTROLS MENU

WORKING SEAT POT WORKING

Hit LEFT/RIGHT Coin Switches to move UP/DOWN Hold ABORT and hit Coin Switches to cycle through choices Hoid ABORT and turn xey to restore orginal setting Just turn koy io save this setting and exit

Figure 2-15 Disable Broken Controls Screen

Main Board GSP Tests

If the automated self-test reports bad VRAMs, choose Main Board GSP Tesis and the screen in Figure 2-16 appears, Tirst run the VRAM simple test. It gives the location of the bad VRAMs. If the VRAMS pass this test, but you think the simulator has a bad VRAM, run the VRAM verify test, H VRAM Simple Test is the same test chat is run in the automated self-test. Ic is nan by the 68010 through the GSP interface and detects apen or shorted address or data lines or missing parts, The results are displayed on-screen with a picture showing the VRAM section of the main PC beard, The good parts are shown in green and the bad parts are shown in red, if an entire section appears in rect, the problem may be with a buffer associated with that section. The test takes about 30 seconds. M@ VRAM Verify Test is a complete memory test run by the GSP. The results are reported on the sereen like in the simple test, The test takes about three minutes to ran. Since the verify test is run by the GSP progrim in the VRAMs, a single bad VRAM can cause the GSP program to crash. When this happens, the 68010 microprocessor reports that all the VRAMs are bad, although probably enly one VRAM is bad. You faust run the VRAM complete test (described be- Jow) to find out which VRAM is bad. if the VRAM verify rest fails, but the VRAM simple test shows the VRAMs are good, you should run the VRAM complete test. If the verify test runs and reports that the VRAMSs are good, then the VRAMs should be goad. M VRAM Complete Test is a complete memory test run by the 68010 dirough the GSP interface. Because

2-13

Page 26

Self-tuse Race Drivin’

Table 2-5 When to Use the Special Function Items

1 settee — ent ee — _ If you see the message Bad GSP VRAM or Bad GSP Color RAM jn the automated selFrest If you have control problems and/or game link problems. IF you see the message Bad Program: ROM in the automated self-test. if your controls: settings are changing even though you have used the Set Controls screen or if the sististies are not being kept carrectly, H you see any message other than /LDSP Board OK for the ADSP PC board test In the automated self-test,

Main Board Controls

Main Boar] ROM Checksams Main Board ZRAM Tests

ADSP Board Tests

Saund Board Tests. DSK Board Tests If you see the message Bad Sound Board in the automated self-test. if you see the message Bad DSK Board in the automated self-test.

the 68010 mins the test, a single bad VRAM does not cause the test 10 report ail the VRAMs are bad fas it does the verify test). Any VRAMs that are bad are shown on the screen at the end of the test. This test takes at least 22 minutes to run. The Pots; & Bitand Pots; 12 Bit screens have the same information as the the Control fiputs screen. They show the voltage inputs from the contro! potentiometers To the A/D converter circuits. As you use a control, the tine on the screen changes as the voltage input changes. If the voltage does not change, you should check that control according to the procedures in = Test bi for Display Errors checks for video dis- Chapter 3, Maintenance and Troubleshooting. lay problems, pay Pi WM The controls under the heading Pots: 8-Bit feed W@ Color RAM is the same test that is performed in the into the 8-Bic A/D converter circuit on the main automated self-test. Ir tests the color RAM and reports the results. PCB. (See Figure 2-19.) These contrals are the gas pedal, clutch pedai, scat movement, shifter (front to back), shifter (left to right), steering wheel position, and shifter force. (The steering wheel position is also checked on the 12-bit A/D converter cecuit. If the numbers do net match, the steering wheel foree is turned off.} W VRAM Shift Register Test checks the shift register part of the video RAMs.

This screen provides more information about che trols than is shown in the Contro! fnputs screen. 1 items on the screen ate described below and shown in Figure 2-18, After you choose any item on this screen and go to that item, you can return to this screen by tuming the key, As you use the controls, the lines should become longer and shorter. If the line does not move, then you have a problem with the control and you should see the information about the control in Chapter 3.

SPECtAL FUNCTIONS MENU EXIT VRAM SIMPLE TEST: 35 SECONDS V&AM VERIFY TEST: 3 MINUTES VRAM COMPLETE TEST: 22 MINUTES TEST VRAM FOR DISPLAY ERRORS COLOR RAM VRAM SHIFT REGISTER TESTVRAM SHIFT EXIT MAIN BOARD GSP TESTS MAIN BOARD MSP. TESTS MAIN BOARD CONTROLS MAIN BOARD ROM CHECKSUMS MAIN BOARD ZRAM TESTS ADSP BOARD TESTS SOUND BOARD TESTS DSK BGAHD TESTS

Figure 2-16 Special Functions Screen Figure 2-17 GSP Tests Screen

Page 27

Race Drivin’

In these controls, 0 Volts appears as no line or a short line and 5 Volts appears as a line halfway across the screen, M In the Pots: 12-Bit screen, shown in Figure 2-20, Sigering Wheel shows the position of the steering wheel. The steering wheel location input is sent to both the 12-bit and the bit A/D converter circuits and is compared, If the numbers do not match, the simulator turns the steering motor force off, Brake Force shows the force on the brake pedal, As you push harder and harder on the brake, the line disappears. If the line does not move, then you have a problem with the brake, the connection, or the 4/D Converter circuit on the main PCB. In the steering wheel and the brake force lines, 0 Volts appears as no line or a short line and 5 Volts appears as almost eight full tines drawn across the screen. (The owo lines on the bottom of this sereen are not used.) M Steering Wheel screen is explained below and shown in Figure 2-21. M Shifter screen is described below and shown in Fig ure 2-23. M Duart does not apply to this simulator. @ Link Connector tests the RS232 channel used to link two simulators tegether,

Steering Wheel Submenu

Use these item if you believe you have a problem with the steering assembly or the motor amplifier assembly. The screen is shown in Figure 2-21. ‘fhe section Steering Assernbly in Chapter 3 explains how to use these lests.

CAUTION Do not service the motor amplifier assembly, which is mounted on the left side of the cabinet. The assembly contains high voltage. if you have a problem with the motor amplifier assembly return the entite assembly to your distributor for replacement,

To move through the menu and the screens, use the coin switches. To exit 2 screen, push both coin switches down, @ Exit returns to the Main Board Controls screen,

M@ Send Force sends a steady force to the motor amplifier PCB, See Figure 2-22, Self-Test

MAIN BOARD CONTROLS

EXIT POTS; 8 BIT POTS: 12 BIT STEERING WHEEL, SHIFTER puUART LINK CONNECTOR

Figure 2-18 Main Board Controls Screen

MH Sine Wave sends a sine wave force to the motor amplifier PCB. ‘This screen is similar to Figure 2-22. WM Square Wave sends a square wave force to the motor amplifier PCB. This screen is similar 10 Figure 2-22,

@ {Triangle Wave sends a wiangle wave force to the motor amptifier PCB. This screen is similar to Figure 2-22, ™@ Closed Loop Test reads the steering wheel position and sends a force to the motor amplifier PCB to sirnulate a simple spring. (@ Line Voltage Calibration can be used to calibrate the sinulator voltage reading to the line voltage reading. Put a voltmeter on the line, then set the voltage on this screen to match. Mt Opto Fest is a test used by manufacturing. W Life Test is a test used by manufacturing quality assurance.

8 BIT AD

GAS CLUTCH SEAT SHIFTER F/8 SHIFTER L/K nts WHEEL LINE VOLTS

  • SHIFT FORCE

Figure 2-19 Pots: 8-Bit Screen

Page 28

Sele-Test

12 BIT AD

STEERING WHEEL

BRAKE FORCE

Figure 2-20 Pots: 12-Bit Screen

CAUTION Do not use the Life Test. it is used only in the factory for testing of potentiometers. If you leave the simulator in this test for a long time, you can destray the potentiométer on the steering assembly.

Shifter Test Screen

Use this screen if you have a problem with the shifter, Before you use the screen, see Figure 3-22, the shifter flowchar, to find out how to use the tests ancl settings on this screen, If you need to repair the shifter or the shifter PCB, see the shifter section in Chapter 3 for further information. The shifter screen is shown in Figure 2-23. Under Shifter Outputs, you can see the voltage outputs change as you push the shifter from left to right and front to back. These numbers show the change in the voltage input from the shifter potentiometers to the Bit A/D converter circuit on the main PCB. The X Pot number changes as you move the shifter handle from left to right. The ¥ Pot number changes as you move the shifter from front to back. After Shifter Power, either a O or 7 will be displayed. Turning the start key switch on causes the shifter solenoid to be energized and the number f to be displayed. Releasing the key switch should display a 0. Exit the screen by pressing both coin switches simulta neously.

Link Connector Test

Use this test if you have a problem when linking nwo simulators together, This test requires a special test connector plugged into the Link Connector on the game.

2-16 Race Drivin’

. STEERING WHEEL

Exit SEND FORCE SINE WAVE SQUARE WAVE TRIANGLE WAVE CLOSED LOOP TEST LINE VOLTAGE CALIBRATION GPTO TEST LIFE TEST

Figure 2-21 Steering Wheel Submenu Screen

The special test connector is a female DB-25 with pins 2 and 3 connected tagether. Contact Atari Games Customer Service on how to obtain a test connector ‘fhe west results are displayed (in color) as shown in Figure 2-24

Main Board ROM Checksums

‘This screen checks the main PC board program ROMs for errors, Use this test if you have a bad program ROM message in the automated self-test or you suspect program ROM failure. ‘fo exit this screen, turn the key. When the checksum test is complete, a hexadecimal number follows each ROM as shown in Figure 2-24. ‘The first two digits in cach hexadecimal number can be any number, but the last ovo digits must be the ones shown in Figure 2-25.

SEND FORCE

PRESS INC TO INCREASE POSITIVE FORCE

PRESS PEC TO DECREASE POSITIVE FORCE

HOLD KEY TO EXECUTE

FO EXIT PRESS INC AND DEC AT THE SAME TIME +6000

128 POT: OAS? TTtE 8B POT: COAE LINE VOLTAGE: 0112

Figure 2-22 Send Force Screen

Page 29

Race Drivin’

SHIFTER TEST

SHIFTER OuTPUTS X POT 157 ¥ POT 127

TURN KEY TO POWER THE SHIFTER

SHIFTER POWER = 0

PRESS BOTH COINS TO EXIT

Figure 2-23 Shifter Screen

Main Board ZRAM Test

This test checks the non-volatile RAM where the simulator statistics and control set-up values are kept. Check the ZRAMs if you think the statistics are incor. fect. Also use this test if the control settings are changing even though you have recently set them with the Set Controls screens.

If the simulator loses power or is reset while it is in this test, then the statistics and the control Settings wilt be lost. If this happens, use the Ser Controls item from the main menu to reset the controls. The statistics canaot be restored,

ADSP Board Tests

Use this item if the ADSP PC board fails the Micropro

LINK CONNECTOR TEST

INTERNAL FEST CHARKEL A CHANNEL & DUART Ing

EXTEANAL TEST CHARNEL A RS232 LINK SWwiTCh GREEN = Pass. RED = FAH,

THIS TEST REQUIRES A SPECIAL TEST CONNECTOR PLUGGED INTO THE LINK CONNECTOR ON THE GAME. THE SPECIAL TEST CONNECTOR FS A FEMALE DE-25 WITH PINS 2 AND 3 CONNECTED TOGETHER. CONTACT ATABE GAMES CUSTOMER SERVICE ON ROW TO OBTAIN ONE.

Figure 2-24 Link Connector Test Screen Self-Test

cessor and board tests performed in the automated self-test. When you select ADSP Board Tesis from the Test menu the screen in Figure 2-26 appears. The icems on the screen are explained below, Wi Exit returns to the Test menu, Ml ADSP RAM Tested by 68010 tests the memory on the ADSP PC board. The 68010 on the main PCB test the ADSP program memory, the ADSP data memoty, and both ADSP output buffers. The memory tests are the standard, complete rests but are run at the 68010's bus speed, which is slower than that of the 2100.

Wl ADSP Program Memory Test .2100. is a Standard, complete memory test run by the 2100 on it own program memory, Since the test program must reside in memory, a bad Program RAM may prevent the test from running. However, because the pro-

PROGRAM ROM CRECKSUMS

CHKSUM EXPECT LOC, CHKSUM EXPECT

A102-Xxo2210R: = S10t—-KXO1
B704 = xx04:7703¥xO3
TS06 = -KX06s4205 = xxO5.
Gk0B_xXxKOS.ikO20 = XXOT
2210XXI0f&s008Xxog
0000 = XXXKA00D = XXXX
0060XXXK5OCGDANKK
0900XXXXf0000 | XXXX

XX = DG NOT CARE

Figure 2-25 ROM Checksums Screen

gram memory is divided into two banks, the test is divided into vo parts. The program to test the upper bank is run from the lower bank; the program to test the lower bank is tun from the upper bank. Unfortunately, the 2100 always starts operating from 2 specific address in the lower bank. Therefore, the lower bank must be Operating to the extent that it can execute a JUMP instruction to the upper bank. These tests operate solely with program memory; they do not require that any data memory be operational. W@ ADSP Data Memory Test is a Standard, complete test run by the 2100. It operates solely with Program memory and does not require that any data memory be functional.

2-17

Page 30

Self-Test

ADSP BOARD TESTS

EXIF AOSP RAM - TESTED BY 66010. AOSP PROGRAM MEMORY TEST .2100. ADSP DATA MEMORY TEST .2100. 2100 TEST IRQ FEST OM CHECKSUMS ADSP SPECIAL FUNCTIONS

Figure 2-26 ADSP Board Tests Screen

W 2100 Test checks the response of dhe 2100 integratcd circuit on the ADSP PC board by copying data from one location to another using a 2100 progeam,

MM IRQ Test checks if the ADSP can generate interrupts for the 68010. Mi ROM Checksums tests the graphic ROMs on the ADSP PC board. When the checksum test is complete a hexadecimal number follows cach ROM as shown in Figure 2-27. The first nvo digits in each hexadecimal number can be any number, but the last two digits must be the ones shown in Figure 2-

  • If the last two numbers are different, then the ROM is bad or it is not on the board,

Mi ADSP Special Functions performs hardware diagnosis for use by a repair technician.

Sound Board

Use these tests if the sound PC board failed the microprocessor and board tests in the automated self-test.

ADSP HOM CHECKSUMS.

GHKSYM:: EXPECT DRIVER ADSP

0000XKXK4NONE
7424XK2910x
agzaxXx24‘10L

9060. 5 HOME

902tOK.40H
o02ztH.405

XX = DO NOY CARE

Figure 2-27 ADSP ROM Checksums Tests Screen Race Drivin’

If the sound PC board failed the test, select this item from the Test menu and Figure 2-28 appears. Many of the tests require an oscilloscope and schematics. These are indicated on the list below. The tests are explained below. MH Fvit returns co the Test menu, B Play Sounds takes you to the Requesting Sound Screen, Follow the instructions on the screen to hear the simulator sounds. i Self-Test checks the sound program ROM and RAM, COMRAM, and 320 RAM. Ml SD ROM Checksums rests the ROMs holding the waveform data, The screen appears in Figure 2-29. it shows the ROM location, a hexadecima) number, and the results of the test for each ROM. ‘the result will be one of the following: Ni-—Nothing is loaded in that socket, No action is required. HAD—The ROM is bad.

OK—The ROM is OK. PROG DEV—The ROM is a program development ROM. 320 Sweep—Runs 2 program in the sound PC board 32010 to generate a sine wave sweep from 20 Hz 10 9 KHz (requires oscilloscope). 320 Tine—Runs a program in the sound PC board 32010 to play a tune, Program ROM—Tests the sound PC board program ROMs with the sound PC board 68000 and reports the results on the screen. Program RAM-—Tests the sound PC board program RAMs with the sound PC board 68000 and reports the results on the screen. COMRAM—Tests the sound PC board communica tions RAM with the sound PC board 32010 and re-

SOUND BOARD TESTS

Exit LED TEST SELF-TEST DAC RAMP SD ROM CHECKSUMS DAC 256 HZ PLAY SOUNDS SA COUNTER 320 SWEEP SB LATCH 320 TUNE 4320 TONE PROGRAM ROM 320 IRQ PROGRAM RAM 320 DAC RAMP COMRAM 3206 DAC ONES 320 RAM 320 SBLOCK

SOUND SOFTWARE VERSION 3.9

Figure 2-28 Sound Board Tests Screen

Page 31

Race Drivin’

ports the results on the screen, 320 RAM—Tests the sound PC board 32010 program RAM with the sound PC board 68000 and re Ports the results on the screen. LED Test—Flashes the Test LED with the sound PC board 68000, DAC Ramp—Nirites to every DAC value with the sound PC boar! 68000. The sawtooth frequency is about 60 Hz (requires oscilloscope). PAC 250 Ha—rites to every fourth DAC value with the sound PC board 68000. ‘The sawtooth frequency is about 250 Hz (requires oscilloscope). SA Counter—Creates an oscilloscope loop for the sound address counter (requires oscilloscope}. SB faich—Creates an oscilloscope loop for the sound black latch Grequires oscilloscope). 320 Tone—Plays a sine wave tone created by the 32010 requires oscilloscope). 320 {RO—Generates interrupts with the 32010 which the 68000 on the sound board recognizes {requires oscilloscope), 320 WAG Ramip—The sound PC board 32010 ramps the DAC Gequires oscitloscope). 320 DAG Ones—The sound PC board 32010 writes walking ones through the DAC latch (requires oscitloscope), 320 SBLOCK—The sound PC board 32010 writes increasing addresses to the Sound Block Latch (re quires oscilloscope},

DSK Board Tests

The DSK board is part of the Driver Speed Kit and tur bocharges the simulator, The DSK board features:

SOUND BOARD TESTS SOUND WAVE ROM CHECKSUMS EFFF 4FC2 FR00 A313 5190 1F88 FO29 BFCO 3138 $A35 FFF Tees PROG DEV

Figure 2-29 Sound Board Sound Wave ROM Checksums Self-Test

Wi extra RAM for storing player races @ exc non-volatile RAM for remembering the Championship Lap Mf extra ROM

@ two separate ASIC systems for increasing the performance level of the simulator The DSK Board Test sereen is shown in Figure 2-30, @ DSK ROM Checksums tests the ROMs on the DSK board, M DSK ZRAM test the additional non-volatile RAM used for storing the race of the Challenge Lap champion. The remaining tests on the menu (ASIC Gloox, ASIC 65xxxx, and DSK Special Functions) are used by the factory for quality testing.

LEDs on the Main

PCB

The LEDs (light emitting diodes) on the main PCB show you the status of various signals on the main PCB, Using the LEIDs, you can check signals from various circuits going to the 68010 processor. The state of the signals is indicated by the LEDs which flash or Stay lit,

Figure 2-31 shows the location of the LEDs on the main PCB. Table 2-4 shows the possible status of the LEDs, with an explanation of what they indicate.

DIP Switches

if you try to enter the self-test, but nothing appears on the screen, use the DIP switch tests. Use the informa

USK BOARD TESTS

EXIT DSK ROM CHECKSUMS DSK ZRaM 4

ASIC 61 VITAL SIGNS ASIC 61 IRAS ASIC G1 INTERNAL RAN ASIC 61 EXTERNAL RAM: SIMPLE TEST 6D SECS

ASIC 65 VITAL SIGNS ASIC 65 CHECKSUM ASIC 65 INTERNAL RAM

DSK SPECIAL FUNCTIONS

Figure 2-30 DSK Board Test Screen

2-19

Page 32

Self-Test

Gonfrom these diagnostic tests to help you fiad the problem. Before you begin with these following tests, be sure that the problem is in the simulator hardware, not in the video display. IF you have a completely dark screen, check the following: @ Do you have power to the video display? @ Are the video display's fikaments li? ®@ Bo you have high voltage to the video display? Tf the answer to any of these questions is no, then you have a problem in the video display. Check the video display service manual included with your simulator for suggested procedure. IF you are sure that the problem is not with the video display, then try the DIP switel: diagnostics shown in Table 2-8. These tests isolate various ICs and systems for woubleshooting. The results of the tests are indicated by the main PC boarl LEDs or on the video display screen. Race Drivin’

Setting the DIP Switches for the Tests

Put a jumper across the DIAGN test points, shown. in Figure 2-30, 2, Select the diagnostic test you want to use with the DIP switch settings.

  • Tura on the self-test switch, 4, Put a jumper momentarily across the RESET test points, shown in Figure 2-30 Changing to Another DIP Switch Test
  • Change the DIP switch settings.
  • Put a jumper momentarily across the RESET test points, shown in Figure 2-30.

Ending the DIP Switch Testing

  • Take the jumper off the DIAGN test points. 2, Put a jumper momentarily across the RESET test points. The DIP switch settings are on in the top position when the main PCB is in the simulator.

Table 2-6 LED Status

Clack LED State of the 68010 processor clock signal.

IRQS LED — State of all 68010 interrupts, i DTACK LED State of 68010 DTACK (dara acknowledge) signal.

LED ‘Indicates Status i

Rum LED State of 68010 HALT signal. On when 68010 is running, Hl Off when 68010 processor is not running. Flashing at 2 Hz if the 68040 cannot run. (The watch-dog. and clock must be running.) CThe Run LED is ef in game mode.)

On when the 68010 processor is running and the timing circuit is probubly operating. i Flashes et 2 Hzwhen the 68010 processor cannot run. (The swatchdog and processor clock must be rauning.) (fhe DTACK LED is on in game inode.)

On when the game board is on,

Offif the processor clock signal is stuck high or low

On in the game mode. Offin hardware diagnostic mode and the early part of self fest. Off if no interrupts are occuring or any interrupt signal is stuck low,

Page 33

Race Drivin® Self-Test

Clock LED

tROs LEO

& Aesat Pains

Test LEDS Fost LED Diagnose Poin

DP Sweets

Figure 2-31 DIP Switch and LED Locations on the Main PCB

Page 34

Setf-Test Race Drivin’

Table 2-7 Using the DIP Switches

Type of Test Purpose and Results DIP Switch Settings : TFs ese7s ‘Watchdog, Test Program ROMs, Test Menu RAMS, and LED Tests |

Unceleated WatchclogPuts the 68010 in a loop. Does rof clear the watchdag counter. Thexxoo0o0o0o0

program RAM does not need to work, I the watchdog is working, the nin LED, DFACK LED, and IRQs LED Mash at 2 Hz and the clock LED 1S On.

Cleared Wirchdog,Puts the 68010 in a loop, Clears the watchdog counter, The programKxGOOO0 O18

RAM does nol need £0 work, if the watchdog is working, the min LER, clack LED, DTACK LED and IRQs LED are on.

‘Test LEDSTests the test LEDs. The progrum RAM does oar need to work. If thexxoQgoao0771

test LEDs are working, they flash at 2 Hz.

Test Progeant ROM 0Tests ROM 0 H and 0 L, which hold the test program. (This test takesxx¥oo0TT11

about 5 seconds.) LED 1 and LED 2 flash together if both ROMs are soot. If ROM 0 1, is bad, LED 1 does not flash. If ROM 0 11 is bad, LED 2 does not Bash,

Test Menu RAM 0‘Fests RAM 0 H and 6 L, which run the rest menu, (This test takesxxoo7112

about 5 seconds.) LED 1 and LED 2 flash together if bath RAMs are goad. If RAM 0 Lis bad, LED 7 does not fash. If RAM 0 His bad, LED 2 does not Bash.

GSP Tests

GSP CommunicationsTests if he 68010 can communicate with the GSP, which producesXXOLYELL

ibe video. If he GSP responds, the LEDs flash cogether, If the GSP dnes not respond, LED 1 and 2 flash akhemately.

Red ScreenProduces x red screen from dre color RAM, regardless of GSP VRAMxxoO21330

input. Lise this to check the rud video outputs,

Green SereenProduces a green screen from the calor RAM, regardless of GSP VRAMKxO14100

input. Use this to check the green viceo outputs.

Blue Screen,Produces a blue screen from dhe color RAM, regardless of GSP VRAMxxka1i00o0

input, Use this to check the blue video outputs.

GSP Memory FillDoes a very slow GSP memory fill so you cin test die pixel scammer.XkKOoTOO O00
GSP VRAM VerilyPerforms the GSP VRAM verily test. Crhis test is aiso in the self-test.)Kxi100000

ROM and RAM Tests

ROM Test LoopThe results are displayecl an the screen.xx100001
RAM Test Loop‘The cesults are displayed on the screen,xxXx1060011

MSP Tests

MSP interfaceTests the MSP interfuee. Results ure displayed on the screen.xXx KiOQG1i141
MSP Auto IncrementTests the MSP auto-increment. Resutts are displayed on the screen.xkxXigdi1liiit
MSP InterruptsTests the MSP interrupts (EROS), Results are displayed on the screen.x¥x1i1daaia21
MSP DRAM VerifyPerfanns the MSP DRAM verify west. (This (est is also in the selftest.)KxX111116

The results are displayed on the screen.

Bus Error Test

BERRThe PTACK timer times oul and generates # bus error (BERR) signal.KxXETr110¢0

‘The results ase displayed on the screen. 2-On; OaQffi Xe Doesu't Maticr.

2-22

Page 35

CHAPTER 3

Maintenance & Troubleshooting

CARE PROCEDURES

This chapter includes maintenance, repair, and troubleshaoting information for your Race Drivin'™ simulator,

The chapter is organizedt with the general information first and the specific information about parts and controls last. The general information includes a schedule for simulator maintenance and inspection, a table with general troubleshooting information, and a table of the voltage levels and test points on the PCBs. ‘The specif ic Information is arranged by the part or control with Maintenance procedures, repair procedures, troubleshooting tables, and troubleshooting flowcharts for each part. In the simulator, the hardware and software are closely related, If you are having problems with a mechanical assembly, always keep in mind that your electrical connections may nat be gond or you may have an electronic problem, ‘To determine what kind of the problem you have, use the self-test screens as recommended ia the troubleshooting tables and flowcharts. If after using these tests and scrvens, you decide to repair a part, the procedures for removal, disassembly, and repair are provided in this chapter. IF a part is mentioned, but not illustrated, refer to Chapter 4, 2 lustrated Parts Lists, for information. ® @ ® B® ®

Page 36

Malorenance and Troubteshoating

Maintaining and Inspecting

Preventive maintenance includes inspecting, cleaning, lubricating, and tightening hardware. Perform the preventive maintenance regularly so you can keep the simulator in top conclition, avoid problems, and maximize your earnings. Preventive maintenance tasks and intervals are shown in Fable 3-1.

Maintaining Your Simulator

For the best performance from your Race Drivin’ simulator, you should check and maintain your simulator accorting £0 the times shown in Table 3-1. How To perform these tasks is explained in the section about that control in this chaprer. You may want to perform these tasks more often if the simulator is heavily used. ‘able 3-2 is the first of ten toubleshooting tables in this chapter. Use this table if ef of your controis are acting erratically ar not responding. If only one contro] is not working, BO to the section about that contol and read the troubleshooting information there. Table 3-3 shows the correct voltage levels to various PC boards and the test points for those voltage jevels, Low voltages to PC boards may cause problems with the contois, with the video display, or in driving. Rave Drivin”

Dashboard Removing the Dashboard

Remove the dashboard to service the steering assembly. See Figure 3-1.

WARNING The dashboard weighs about 40 pounds. Be careful when you remove it,
  • Turn off the power and unplug the game.
  • Take off the under-dash cover over the brake and clutch pedais. it is held in place by two Phillipsheacl screws. See Figure 4-1 for an iltustration.
  • Remove the four nuts on either side of the dashboard and take out the cariage bolts.
NOTE Do nat remove the four tamperproof screws around the steering wheel unless you are replacing the steering assembly. Even then, remove the baits only alter the dashboard is out of the simulator.

Table 3-1 Maintenance and Inspection Items

Video Display Face and Shietd

Game Exterior

Gas Pedal Interior Componcats Key Switch Shifter

Steering Wheel Part When to Check What te Check and Maintain Coin Mechanism Every 6 months Clean, . Brake and Clutch Pedals Every 3 months. Oil all bearings. Check ihe switch and switch actuator disiance, Every 6 weeks

Every 3 months

Every 6 months Every 3 months Every 3 months Every 3 months

Every 3 months fake off the video display shield and clean the shield and the fuce of the video display. (Carbon particles emitted by the steeting motor collect on the shield and video display, obscuring the view.) Make sure the glides are down, ‘The casters may be damaged ifthe glides are not usec, Be sure the rubber stop behind the clutch on the firewall is still on. Spray the pivot pin, spring cable, and pulley with dry Teflon spray. Clean. Lightly oil the spring and shaft. Check the shilter boot for damage. Make sure the foam in the boot ts in place, Grease the threads. Check the rubber stops and tighten the screws: that bald the steps on, Make sure the potentiometer shaft has a very light coat of grease. Make sure the stop assenibly on the motor shaft is tight on the shaft. To prevent injuries, replace the steering wheel if the sim or spoke padding is worn out.

Page 37

Race Drivin’ Maintenance and Troubleshooting

Table 3-2 Troubleshooting All Controls | Problem Solution All controls do net respond ar respond eritically. 1. Go through the Set Consroés screens in the self-test,

  • Have you recently installed a new PCB or new controls? If so, gO through the Set Controis screens in the self-rest,
  • Check the ZRAMs in the self-test for errors,
  • ‘The simulator may have lost power during a ZRAM (est. Go i shrough the Ser Controls screen in the self-test, i
  • Uniock the bottom service door to reach the nuts 7

on the carriage bolts underneath the dashboard at Installing the Dashboard

the rear, Take off the nuts and washers. 1. Sit in the seat with the dashboard in your lap. Pult the seat towards the video display. Lift up the

  • Also from the rear, disconnect the four connectors dashboard and slide it in on the side panels. from the dashboard harness to the simulator harness. 2. Feed the dashboard harnesses through the front
  • Remove the Phillips-head screws on the front and Panel curouts. Push the dashboard into place, under the dashboard. 3. Hold the <lashboard in place and put the carriage 7, The dashboard is now supported by the top lip Doles peeral side. Put the washers and the and the side panels. Sit in the simulator seat and ” pull the dashboard forward and out of the simuta- 4. Go around to the back of the simulator and con- Tor onto your fap. nect the steering assembly and the switch harness- ¢s to the simulator harness, Then instal} the ovo carriage bolts with washers and nuts under the Table 3-3 Voltage Inputs and Test Points on the Simulator PCBs
PCBVoltageTest Points__Source and Purpose
Main+5E0.1 VDC452+5 V Switching Power Supplyi
Main+1SH0.G VDC+15V1Regulated and supplied by the APU PCB.

Used by the 12-bit A/D converter and runs the +12 VDC regulator.

Main+22 VDC-22V1Unreguiated and supplied by the APU PCR,

Runs the -S¥ regulars,

Main*32t05 VDC+C127Regulated and comes from the +15 VDC supply.

Usad by the 12-bit A/D converter and the sound PCB,

Main540.2 VDC-C125Regulated and comes from the unregulated -22 VDC suppty.

‘Used by the 12-bit A/D converter and dhe sound PCB.

ADSP+3 YDC#5Vi or +5V2Regulated and supplied from the Main PCB through the interface cable,
Sound+5 VDC+52Supplied and regukued by the main PCB through the sound power cable.

Used by the logic circultry.

Sound+32 VDC105B Pin 4Supplied and regutated by the main PCB through the sound power cable,i

Used by the analog circuitry. i

Sound-S VDCSR Pin 4Supplied and regulated by the main PCB through the sound power cable,H

Used by the analog circuitry. i

Sound+3 VDC+5V2Supplied and regukued by the main PCB through the interface cable,i
Sound+15 VDC103B Pin 11Supplied by the APU PCB through the main PCB.:

. Used by the 12-bit D/A converter on the sound PCB i

APU+14VDCSee schematicsUsed by the coin counters and the audio amps on the APU PCB.Hl
APU“HVDCSee schematicsUsed by audio amps on the APU PCB.H
APU-22VDC.See schematicsUsed by the main PCB.i
APY+HSVDCSee schematicsRegulajed; used by the main PCB.
Page 38

Malntenance and Troubleshooting

dashboard at the rear,

dashboard.

  • Install the under-dash cover above the brake and 3, Install the two tamperproof screws and washers. Finally install the Phillips-head screws under the Race Delvin'

Steering Assembly If you have problems with the steering assembly, check the troubleshooting suggestions in Table 3-4. Always perform the Set Controls screens in the self-test clutch pedals. Screw in the two Phillips-head first. serews that hold it in place.

  • Close and lock the service door.
Th5520Be230198RAD~
2d e178ge-6210Bue14-20.x 1.25ttam Not Shown:
Cartage eanHet Gap Sera‘Tampemroat Screw‘ADETTATO1
17000-1464pisces)boraneey Switch Hamans Assy,

144-20 Hex Net Wa" Flat Wesher 7607002 BK

a" Pander Washer7x oy Sutah A
wrrorant8048480-011asAse.
Putt-Ga Spring NutSteering Assy.H£eaONTTTT-01
(Sao Figures5)|PAa
mie|sus

VB-16.x 1,0 BUIKHA. Ser |p eel Key Sich Oo 196007-001 bos ‘Trrend Lode Adhesive} 75-51088

$4LEitZax Ver
ioEECantoge Galt
|Ngi,elton.
4tRK3i

& i ay

Lesstee

I Ke si j re sep aT7ORAANAS ae

4-20 Nutbe¥

+176014.2050 4 10 Fs Washer

Flat Washer?sor548 placa)
ae |céBidet Nut

3 75-0453,

V4-20 x 1.25,O4e6S4O1"|
Carlage Bex|wie Penel Piste+6" Lock Washoe
her!Be04645801

‘Switch Bezel: hes

scuazon| 1ses-naeiCover
Rise Pusntarion Sviten75-9960| Tamparprost ServaSmear W
#892 BobaScearing Wheel
oar770-01Washer Assy,{a places)bev —Con
SaavAbor Pavel‘YTEO14-304DDaB457-07
047722-03 || 1weea3-002‘#10 Flat Washer‘Steering Wheat He
‘Seat Abort DoraGanon "Span Ast”feptscts}=
176005-4108Barton WeenDATS“T7ROR-005
M092 x 050yo0ns400t| oni PaSieedng Wheolrasa
Tamparrcel ScrewSnap-Acton SwetchVrs00200T
eeapboeaneeEconbolPans! OocalWasher[Soabid Can Screw

4175014-3040 ‘AOST?4B-01 s77o10-860

#19 Fist Washer’‘Soot Adjust Harness Assy.W446 Locks

(s ptaces)|

Figure 3-1 Removing and Installing the Dashboard

3-4

f

Page 39

Race Drivin’

Greasing the Steering Assembly

Grease the steering assembly threads and stop regularly according to the maintenance schedule and if turning the steering wheel becomes difficult (and the problem is not the steering motor). 1, Take out the dashboard. See the procedure in the section Removing the Dashboard.

  • Grease the large threads on the stop assembly. Sce Figure 3-5.
  • Put the dashboard back in. See the procedure in the section Installing the Dashboard.

Replacing the Steering Assembly Potentiometer

Replace the potentiometer ufter you have followed the flowchart in Figure 3-2, 3-3, or 3-4 and you are sure the problem is the potentiometer, 1 Take out the dashboard. Follow the instructions in the section Remeving the Dashboard.

  • Loosen the set screw that holds the potentiometer shaft in place. See Figure 3-5. Remove the nut that Maintenance and Troubleshootlng

helds the potentiometer in the potentiometer bracket. Take out the potentiometer. if the small Spring that hoids the potentiometer bracket on the stop bracket is broken, replace it. . Solder the wiring harness to the new potentiometer, Connect the red wire nearest the shaft, the clear wire in the middie, and black wire at the end.

CAUTION Carefully tollow the instructions for in- Stalling the new potentiometer. if you do not, you might destroy the potentiometer.

Set up the potentiometer, Hold the new potentiometer with its shaft facing you and turn the shaft as far as it can go in the counterclockwise direction, Then turn the shaft back about 15 degrees. Face the stop bracket on the end of the motor; then turn the motor shaft as far as it will go in the clockwise direction, . Apply one drop of light oil to the potentiometer shaft before you install it in the bracket, » Enstatl the potentiometer into the potentiometer bracket with the flat of the shaft facing down and

Table 3-4 Troubleshooting the Steering Assembly

Steering wheel is difficult to am,

Steering has no feedback.

Steering is very jerky.

Steering wheel can spin more than three times around. Force on the steering wheel changes. Problem Solution ! Steering wheel does not respond or responds 1. Go thepugh the Set Controls screens in the self-test. H ematically, 2 . Check the Controf Inputs screen to see If the potentiometer input to | the board is functioning correctly. The steering wheel and wheel lines, which both indicate steering wheel position, should smoothly appear and disappear as you tum the wheel,

  • Check the connections ro the potentiometer and to the motor.
  • Check voltage ievel to main PCB. See Table 3-3. Grease the threads. Check the steering assembly for broken parts. Check the motor bearings by tuming the shaft and seeing if it spins freely, |
  • Try the Sef Controls screens in the self-test. - {
  • See Figure 3-2 0 determine the cause of the problem. H Some jerkiness is OK.
  • Try the Se/ Controls screens In the self-test,
  • If you think the steering is very jerky, see Figure 3-4 for more infor. | mation. Steering wheel is turned 2] the way lo one side or 4, Try the Set Controls screens in the self-test. the other during play and stays there. 2, See Figure 3-3 for more information.

Replace the stop assembly and the potentiometer, ‘The force on the steering wheel should be ighter when the seat is closer to the dashboard and harder when the seat is further away. This so children, who sit closer to the dashboard to drive, sill be able to tum the steering wheel easily.

Page 40

Maintenance and Troubleshaating

root wool Res no Tough. during gare play (athouptt Sinetron gates ars ho aboaity bled tha Sor Costa's Berge

On tho Coste ‘scr09n tha lop prauaediastan ans “Fnac g whoa patton tha ala sealgnielia assem board iaereso arroyo a emoctily Wo Sarg ts yor 15 Vata whon you hn tha ana sper hoes vines hocrwisa?

Froubahock ihe We AG cheat on tha rtin PCB Soo tho mai PC8 echomalla. Gniha Const Inputs scroon tha bette ‘ehpel ino appaara Grmnttey to tho rght 22 yout tha steering whoo! socked.

oar Contras fcz00N Bnd choose tse Seer Whol hem. Cnoase ha Sard Feeea Vest item 09 tatertenl,

he ‘Chock te rocistice to tho maker ‘who Hs cote. Tho snertianc® maid ne betwen 8 are 52 Ct,

maior iboted TP]

‘CAUTION “tro carat tal oktiod hee the ‘mueing, oven though sem appear Pat way. Urpag the garno ara wll 5 errata batcen ramauing th thr ‘shen airotTee aseomty {ibm 0 gene,

Figure 3-2 Steering Wheel Has No Feedback and You Have Tried the Set Controls Screens

3-4 hack Uae vonisarcy of tho thariar sreoeLon tia molar, (Test ara tha two wees coming cut of thd

Fr. Chwih Dis hase cere OE Race Drivin’

Page 41

Race De Maintenance anc! Troubleshootlag

‘Steering whoel is turned at the way Codewisa or Counterclockise durg gare lay ane you have aoady tied iho Set Conbols sxc0n,

Onihs Contin

‘orng whes! Clockatto,

‘On he Conboy Movisscreen, tho whaet Sng 21 ‘ho batam appears smoothly to {ha fight as you tut the slewing whet

Troublasheot tha BBL AD excuit ‘on tho main PCB. Soe the main PCB schemas, Troubtesheot ths 12-0) AD Sitexit on tne msin PCB, Sea tho. malt PCB <chamatic,

Goto the Main Board Conus ‘Strom aNd g¢ into the storing wheel menu, COIS the mangio Wave test,

CAUTION

‘trokor amebtig assemtiy sree tha gare, ‘Does the tearing wheet force change smeoliy trom Slockwiss to counerciockiee when YOu do tha tal wave xe507 Hod the eerng whee when you da tres best Check tho malor ampliter OB 6155 red the calves ‘rom tha main boar ba tha motor ampli assermly. Myou IHirk the prota la on the srctor ampslior astombly, you sist seturn tng entira aaaoently 10 “your gisinbutoe far sepsis,

Figure 3-3 Steering Wheel is Turned All the ‘Way to One Side and You Have Tried the Set Controls Screens

Page 42

Maintenance and Troubleshooting

Staring wivael # very [erty and you have alroadly trios 610 Sel Conareis soreOh.

Onithe Contza's Inpur sergen, lhe stearing whee! Faw appaaré stnoalhiy t9 168 right 0% you bum tho sieving ‘wheel cocewlse,

“Got the Mian Board Canes ser0an and go mio me stoering,

force change.) ‘Check tbo mtallallon of ene potersiometer, Replace tho patertiametor. Troubleshoot the ‘2H AWD eizcull on tho main PCB,

Teoublashoot the bt AVP cizcult onthe malt PCR.

‘Chack iho motor arghiflar PCB iueee and the Come coche eat 5 Irarn sha main boss ta the trotar arrpifiar asaeeiby whan: raha watt ned you brink the grablert i on the moter amplisee Se dadaatated he _assombly, you masst eeturt (he eerie osgeermtly LO ‘you distributor tor reper. Race Drivin’

CAUTION The aucutry & not isolarectiram the main #9, tea thovgh it may appene thalway, Unpivg ine game aod wa S mines bekore rortening the the renee ampeficr assembly fram the game.

Figure 3-4 Steering Wheel Is Jerky and You Have Tried the Set Controls Screens

the rab in the keyhole.

  • Put the lock washer and nut on the potentiometer shaft and tighten the nut. Do not turn the potentiometer shaft from the position at which you set it.
  • Insert the potentiometer shaft into the motor shaft; tighten the socket-head screw.
  • Check the alignment of the potentiometer and the moter by carefully turning the motor shaft as far as it will go clockwise and counterclockwise. Check that the potentiometer shaft turns as far as the mo-

3-8 tor shaft turns in both directions. {f the potentiometer shaft stops turning before the motor shaft stops turning, then do steps 4 through 9 again. 11, Put the dashboard back in the simulator, following the instructions in the section Jastalling the Dashboard.

  • Go to the Set Controls screens in the self-test and re-initialize all the controls.
Page 43

Race Drivin'

NOTE You must go through the Set Controls screens in the self-test because you teplaced the potentiometer. Hf you do not do this, the simulator will not work correctly,

Replacing the Steering Assembly Motor

Replace the steering assembly motor if you have followed the flowchart in Figure 3-2 and you are sure that the motor is the problem. Another reason to replace the motor is if the steering wheel is difficult to tum and the problem is not iubrication or the mechanical parts. Before you replace the motor, check the hamess connections to make sure they are good.

Removing the Steering Assembly Motor

1, Take out the dashboard. Follow the instructions in the section Renioving the Dashboard.

  • Carefully peel off the Atari Games decal on the hub of the steering wheel. The Steering assembly is shown in Figure 3-5.
  • Unscrew the socket-head screw under the decal. Remove the screw, the washer and the hub cover, 4, Remove the large qut under the hub cover with a 1 1/16-inck socket. The nut is torqued to 50 footpounds,
  • Take off the washer and the steering wheel.
  • At the other end of the Steering assembly, remove the potentiometer from the end of the motor shaft by loosening the small screw at the end of the shaft. Take off the potentiometer and the potentiometer bracket. 7, Remove the nut at the end of the moror shaft which holds the stops on the shaft. This nut requires a 1 1/16-inch socket and is torqued to 50 foor-pounds. Remove the washer.
  • Remove the four tamperproof serews that hold the steering assembly on the dashboard, These are torqued to 340 inch-pounds. Take the steering assembly and the motor support plate off the dashboard,
  • Use a puller to loosen the stop assembly on the tapered shaft. You must remove the stop assembly at the same time as you remove the stop bracket,
  • Remove the four socket-head screws and washers that hold the stop bracket on the motor. Pull the Stop bracket and the stop assembly off the motor shaft. Maintenange and Troubleshooting

Checking the Steering Assembly Motor

  • Do the following tasks before you re-assemble the Parts on the new motor: a. Tighten the socket-head screws that hold the tubber stops in place. b. Generously grease the threads. ¢.Check the spring that holds the potentiometer shaft on the stop bracket, If it is broken, replace it d.Check the round stops on the corners of the large rectangular stops on the stop assembly, Make sure the round stops are not cracked or broken.
  • Put the stop assembly into the holes in sides of the stop bracket. Push the stop bracket and the stop assembly on the shaft of the new motor, (When you tighten the nut on the end of the shaft the stop assembly will be correctly seated.) Put the key slot on the stop assembly over the key on the shaft.
  • Screw the four socket-head screws and washers into the stop bracket and motor, Install the ground wire under the wide washer at the top left screw.
  • Replace the suc and the washer at the end of the motor shaft. ‘forque the nut to 50 foot-pounds.
  • Set up the potentiometer. Hold the new potentiometer with its shaft facing you and turn the shaft as far as it can go in the counterclockwise direction. Then turn the shaft back about 15 degrees clockwise.
  • Face the stop bracket on the end of the motor; turn the motor shaft as far as it will go in the clockwise direction. 17, Apply one drop of light oii to the potentiometer shaft before you instal] it in the bracket.
  • Install the potentiometer into the potentiometer bracket with the flat of the shaft facing down and with the rab in the keyhole,
  • Put the lock washer and nut on the potentiometer shaft and tighten the nut. Do not turn the porentiometer shaft from the position at which you set it. 20, Insert the potentiometer shaft into the motor shaft; tighten the socket-head screw.
  • Check the alignment of the potentiometer and the motor by carefully turning the motor shaft as far as it wit go clockwise and counterclockwise. Check that the potentiometer shaft tums as far as the motor shaft turns in both directions. if the potentiometer stops turning before the shaft stops turning, then do steps 1$ through 20 again.
Page 44

Maintenance end Troubleshooting Race Drivin’

+770%0-280 9214-18 Looknust

‘FrBOREOTS Exonsion Speing 199018-00t 10-Tura Pat 998458-01 Pat Grackat:

048649-01 ‘Swearing Motee Support 29018 38-32 Sevew| ATTOFO-244 #40-32 Lock

Figure 3-5 Maintaining the Steering Wheel

22, Using the four tamperproof screws, install the steering assembly and the motor support plate on the dashboard. Put Loktite on the carriage hoits before you put the nuts on them. Tighten the nuts to 340 10 inch-pounds so the steering assembly will not twist on the dashboard.

  • Install the steering wheel on the steering hub. Put the hole in the steering wheel over the alignment stud on the hub. (See Figure 3-5. 24, Put on the washer and the large nut. ‘Torque the aut to 50 foot-pounds.
  • Install the hub cover, split-lock washer, and the socket-head screw. Put Loktite on the screw before installing it. Tighten it to 95 inch-pounds.
  • Replace the Atari Games decal on the hub.

3-10 Se

‘AOABSSIOF =) } ‘Sicering Assy. Hamess ee 17990.200 8 re ‘ is 7easiz 76-0955 Den i om Lock Weashor we ‘oo tnoee

  • Put the dashboard back in the simulator, following the instructions in the section Installing the Dashboard.
  • Go to the Set Cantrofs screens in the self-test and re-initialize all the controls.

Replacing the Steering Assembly Stop It is unlikely that the steering assembly stop will have to be replaced. If it does, follow the instcuctions in Replacing tbe Steering Assembly Motor for assembly and disassembly. You also must replace the potentiometer on the steering assembly.

Page 45

‘Race Drivin'

Key Switch Assembly

Oiling the Key Switch Assembly

Table 3-5 lists what can go wrong with the key switch assembly.

Oif the key switch bezel ring and shaft regularly, when tuming the key switch becomes difficult, or when the key squeaks, i Tum off the power. Remove the key switch plare. 2 Take the key switch assembly out of the dashboard by removing the two cariage bolts and locknuts.

  • Lightly oil the shaft and spring of the key switch. See Figure 3-6. Check that the spring is not broken, Hf it is, then ceplace the spring following the procedure under Repairing the Key Switch. 4, Replace the key switch in the dashboard and install the key switch plate.

Replacing the Spring in the Key Switch Assembly

If nothing happens when the key curs, and there is no resislance to turning, you may need to replace the spring.

  • Tum off the power. Remove the key switch piate. 2, Take the key switch assembly out of the switch plate by removing the two carriage bolts and tock- Tits,
  • Remove the retaining tig from the back of the key switch case. See Figure 3-6, 4, Loosen the socket-head screw on the brass actuator with a 5/32-inch Allen-head wrench.
  • Remove the other retaining ting inside the case. Pull out the key. Take out the brass actuator, the old spring, and the nylon washer.
  • Put lithium grease (Atari Games part no. 107029- Malntenance and Troubleshooting

001) inside the collar. Wipe off the excess grease. 7 Put one end of the spring into the hole in the side of the case.

  • Push the shaft back into the case far enough to mount the spring on the shaft, You may have to cut the legs of the spring to the correct length so that they do not interfere with the operation of the switch assembly.
  • Put the brass actuator into the case with the actuator pin facing the key and opposite the switch. Catch the free end of the spring under the pin. Push the actuator and the nylon washer anto the shaft. 10, Push the shaft through the case and install the two retaining rings.
  • Adjust the actuator on the shaft until it is parallel to the roller on the switch. 12, When the actuator is against the case opposite the switch, the key should be vertical. if the key is not vertical, turn it until it is. Tighten the screw on the actuator, 13, Use a piece of a manila folder or any other flat material about .015 inches thick to adjust the switch distance. Hold the actuator against the switch so that the switch clicks once when you cum the key. If the switch is too close, it will click twice instead of once when you turn the key. Tighten the screws on the switch when the position is correct. Release the actuator. Check the setting. When you turn the actuator against the switch, the switch should click, but not be pressed all the way to the switch body. 14, Put the key switch assembly back on the dashboard and replace the key switch plate.

Tightening the Screw in the Key Switch Actuator

If nothing happens when the key tums, and it turns more than 90°, you may need to tighten the screw on the actuator. i. Tum off the power. Remove the key switch plate,

Table 3-5 Troubleshooting the Key Switch Problem _ . Solution ‘Key does nor retum when timed and has no. The actuator screw may be loose or the spring may need to be re- Tesistance, placed. . Key turns more that 99°, The actuator is loose; tighten the screw on the actuator. Key tums, but nothing happens. Check the snapaction switch, switch connectors, actuator location, and harness connections. Key squeaks when tumed, Olt the collar and shafc,

3-11

Page 46

Malnenance and Troubleshooting Race Drivin’

75-0408 176008-110 #10 Lock Washer 410-32 Soc-Kd. Cap Scraw stems Not Shown: 172020-0614 ‘Spring Pin TREO 10-32 Soc-Hd. Cap Soraw 75-0405 #10 Spillt-Lock Washer

7214123 ‘#4-40 Pan-Hd. Screw 176014-1018 ADATPST-O Key Switch Hamess Assy.

Figure 3-6 Maintaining the Key Switch Assembly

  • Adjust the actuator on the shaft until it is parallel to in Figure 3-6, the roller on the switch. See Figure 3-6. 1, Turn off the power. Remove the key switch plate.
  • When the actuator is against the case opposite the 2, Take the key switch out of the dashboard by ne switch, the key should be vertical. If die key is not moving the two carriage bolis and locknuts. vertical, turn it until it is. Tighten the screw on the an actuator, 3. Remove the two Phillips-head screws that hold the snap-action switch on the key switch assembly. ©
  • Now hold the actuator against the switch and move Take off the switch. Take the harness off the # the switch so that when you turn the key, the switch. i switch clicks once. If the switch is too close, it will click twice instead of once when you turn the key. Tighten the screws on the switch when the positon is correct. 4, Install che switch on the assembly, bur do not tight en the screws. The roller on the switch should face the brass switch actuator, i 5. Loosen the screw on the brass actuator. Adjust the 3x Replace ihe ey, sich Piste, actuator on the shaft until it is paraltel to the roller on the switch. Replacing the Switch on the 6. When the actuator is against the case opposite the
  • switch, the key should be vertical. If the key is not Key Switch Assembly ; vertical, turn it und it is. Tighten the screw on the Replace the switch if the key turns but nothing hap- ackiator. pens and the problem is not the spring, the actuator, or the connections. The key switch assembly is shown Now hold the actuator against the switch and mové::; n

3-12

Page 47

ace Dalvin’

the switch so that when you turn the key, the switch clicks once. If the switch is too close, it will click twice instead of once when you rum the key. Tighten the screws on the switch when the Posilion is correct.

  • Put the harness on the new switch. Connect the black wire to the C {or COM) terminal, and the white/black wire to the NO terminal,
  • Put the key switch assembly back into the dashboard and install the key switch plate.

Clutch Pedal ‘The clutch is part of the clutch and brake pedal assembly, if you have trouble with the clutch, First go through the Set Controls screens. If that does not cure the problem, see Table 3-6, Troubleshooting the Chitch Pedal. IF you must repair the clutch, but you cannot do so immediately, you can disable the clutch circuit. All drivers mist use the automatic transmission if you do this. Do thit onhy as @ temporary measure. Repair the clutch as soon as possible. To disable the circuit, go to the Disable Broken Conirals screen in the self-test and choose broken for the clutch,

Maintaining the Clutch and

Brake Pedals

Take the pedals out of the simulator to maintain them. Regular maintenance includes oiling the pedals, which should be done with the pedals out of the simulator, since you cannat reach all the points and you may get oit on the PC boards below the pedals when they are in the game.

  • Tura off the power and unplug the game. 2, Take off the under-dash cover above the pedal assembly. Use a Phillips screwdriver to remove the four screws that hold the cover on. Muintenance anc Troubleshooting
  • Unlock the bottom service dear, Unplug the harness connector to the pedal.
  • The back of the pedal assembly is above the main PC board. Remove the four nuts and fender washers holding the pedal assembly to the cabinet, After you remove the nuts, the pedals will hang in the same position.
  • Go to the front. Twist and pull the pedal assembly counterclockwise to avoid the bottom of the dashboard,
  • Put light oil on the eight bearing points shown in Figure 3-8.
  • Before you instail the pedai assembly, check the following, a.Can you push the brake pedal 1/4 to 1/2 inch before you feel resistance? If you feel resistance before this point, first check the bearings to see if they are moving. If the bearings are moving, adjust the nut on the bmke spring retum shaft so that the pedal has at feast 1/4 inch of free play. b.Does the pedal return to its testing location? if not, check if the return spring is broken or the bearings are binding. ¢. Does the brake pedal move at least 1/4 inch before the switch clicks? If not, adjust the clamp on the white plastic actuator until you have 1/4 inch of play in the pedal. Make sure the switch clicks before you feel resistance on the pedal, & Put the pedal assembly back in the simulator, Install the fender washers and the locknuts. Connect the simulator harness.

Replacing the Clutch

Potentiometer

Do not replace the potentiometer until you have per formed the Set Controls screens. Check to see if that solves the problem. If not, follow the flowchart in Figure 3-7 to make suse that the potentiometer is the

Table 3-6 Troubleshooting the Clutch Pedal

Problem Sofution

Clutch does not work or works erratically, 1, Perform the Set Controls screens in the self-test. 2, Follow the flowchart in Figure 3-7 to find the cause of the problem,

  • Check connections,
  • Check voltage levels to the main PCB. See Table 33.
  • If you bad disabled the clutch circuit, but the clutch is now re- Pairecl, choose working on the Disable Broken Controls screen. Does not return, 4, Check the bearings, 2 The springs may be broken or weak,

3-13

Page 48

Maiatenance and Troubleshooting

GotaContat aps ecraan In

othe Doss the BN AD tina Jorthe other ines on Teeubioshent the &-bt A/D contra mua seocenty whan the scrnen move Enmootrey when chouten tha main PCB, those otter contro ana AI operas Vs antral?

‘Troutteshoo! the #-bH A droui on the main PCB. Race Drivi

Figure 3-7 Clutch, Seat, or Gas Pedal Is Not Working or Working Erratically and You Have Tried the Set Controls Screens

Page 49

ace DrivinY

problem.

  • Turn off the power and unplug the game.
  • Take off the cover above the pedal assembly under the dashboard, Use a Phillips screwdriver to remove the four screws that hold the cover on.
  • Unlock the bottom rear service door. The back of the pedal assembly is above the main PCB. Disconnect the simulator harness from the assembly, Re- Move the washers and nuts holding the pedal assembly to the cabinet. After you remove the nuts, the pedais will hang in the same position.
  • Go to the front of the simulator. Twist and pull pedal assembly counterclockwise to avoid the bottom of the dashboard, |. See Figure 3-8 for an illustration of the pedals. The clutch potentiometer is mounted on the brake side of the pedai assembly. Loosen the locknut on the potentiometer with a 1/2-inch flat wrench,
  • Loosen the screw on the small gear with a 3/32inch Allen wrench,
  • Take off the gear, nut, washer, and potentiometer, Remove the wires on the potentiometer, we
  • With the shaft of the new potentiometer facing you and the terminals pointing up, solder the black wire on the left terminal, the yellow on the midktie, and the red to the right terminal,
  • Put on the new potentiometer, Insert the key into the key hole in the assembly frame. The potentiometer terminals must point up, Put the nut and washer on, but do nat tighten the aut ail the way, 10, Put the gear on the potendometer shaft. The screw must be vertical and over the flat pact of the shaft, Make sure that the gear meshes with and is directly over the gear below. Tighten the screw. Tighten the nut on the potentiometer. . Carefully press the clutch pedal and make sure that the potentiomezer shaft turns until the pedal reaches its stop. If it does not, re-install the potentometer, following steps 9 and 10, 12, Put the pedal assembly back in the simulator, Install the fencer washers and the locknuts. Re-connect the simulator harness,
  • Now switch on the seff-test and go through the Set Controls screens. Muintenance and Troubleshooting

Replacing the Clutch Springs

Replace the clutch springs ff the clutch does not return to position and the springs are weak or broken. Sec Figure 3-8 for an illustration of the pedals.

  • Turn off the power and unplug the game.
  • Take off the under-dash cover above the pedal assembly, Use a Phillips screwdriver to remove the four screws that held the cover on the cabinet, 3, Open the bottom rear service <loor. The back of the pedal assembly is above the main PC board. Disconnect the simulator hamess from the assembly. Remove the washers and nuts holding the pedal assembly to the cabinet. After you remove the nurs, the pedals will hang in the same position,
  • Go to the front of the simulator, Twist and pull the pedal assembly counterclockwise to avoid the bot tom of the dashboard, 3, Remove the metal stop bracket on the assembly with the rubber bumper pads attached 0 it. Remove the two socket-head screws, one on either side, which hold the bracket to the frame. (You do hot need to remove the rubber bumper pads.) Pull the stop bracket out the assembly.
  • Take off the locking tabs on the end of the spring shafts. Use an Allen wrench to remove the sockethead screws on the tabs.
  • Push the shafts out through the assembly frame and remove the springs.
  • Install the new springs, making sure the ends are hooked over the cut-out areas on the nylon shaft covers.
  • Push the spring shafts back into place and reinstail the locking tabs. 10, install the stop bracket. Make sure the pedal shafts rest against the rubber bumpers. Put the pedal assembly back in the simulator. Install the fencer washers and the focknuts. Re-connect the simulator hamess, 12, Now switch on the self-test and go through the Set Controls screens. =
NOTE You must enter the self-test and go through the Set Controls screens because you repaired the pedal assembly. Otherwise the simulator will nat work correcty.
NOTE Enter the self-test and go through the Set Controls screens when you replace the pedal assembly. Otherwise the simulator will not work correctly.

3-15

Page 50

Malntenance and Treubleshooting Race Drivin’

4 407043-001 Light Oil

NOTE: Lubricate on bolh ends of shafts.

046985-01 b4s40t-01 ‘Spring Housing Spanar

T2612 _|Sene Screw Tlureh Link

7Rg812 6-92 Hex SooHd Cap Seew AFPO10-236 98-32 Loosen 75014-1026 9 Flat Washer q7ater3604 "4a" Spacer 72-8808 9832 Screw

O4BSDE-0T Spring Front Shait Cover

peesa7-o1 4° Ciutch Spring Shak

94024903 +4-Tooth Spur Gear

04024501 £0-Taoth Spur Gaar| reeea6as Sat Sertrw on 6O-Feorn Gees|

‘Thiteh Exienskon Srna y60094-001 Broke Sasten| Teds | ‘4-86 PhESps-Hd. Screw 17010-2352 44-40 Lockout | 79200-2200: Actuate! Clamp

‘O46383-0F Clutch Pedat

Apagaon-o1 Braka Pedal Asay. finetuaas atrain gauge & stain gauge hamess}} 986382-03 Brak Sudan Acruatar | I7PO1O235 Lockanut

paesBe-01 o° Clutch Shatt

046970-01 ‘Clutch Beauing Tad

4896-01 lui Spring Housing agaae.ot Brake Enc

paesE8-01 Podal Pot Shat 173012004 Aetalnlg Ring rro012-004 ¢ Rewining Ring

177982007 Stain Gago

Figure 3-8 Maintaining the Clutch and Brake Assembly

3-16 Assembled Cluteh & Brake

‘¥77DOaT AS1E26 Nid 16007-00% ‘Thread Lock Adheshe

9s5a90-01 ‘Brava Rod

04290-01 Urethane Brake Spang

AOSABI7-OL Brake POR TEBE

Ws" Spacor T7BA20-08 PCB Siedolt

477010-236 Locknut

7ESSA0B 14-20 Carlage Bott 17t002-41+ Preeit-On Spring Nut THO 700r Fender Washer ‘+77010-244 144-20 Lock

AD46330-01 Brake & Catch Hamoss : :

Page 51

aoa

“eeane NN Gowanewene® Race Drivin’

Brake Pedal

The brake is part of the clutch and brake pedai assembly, For maintenance procedures, see Maintainfg ibe Chetch and Brake Pedats, above.

Repairing the Brake

The brake may not work for several reasons. Before you do any repairs, always perform the Set Controls screens in the self-test; then try the brake to see if this corrects the problem, If that does not repair the problem see Table 3-7, Troubleshooting the Brake Pedai and follow the flowchart in Figure 3-9. The test procedures in the flowchart are explained below. H you must repair the brake, but you cannot do so immediately, and you want to continue to use your game, you can disable the brake circuit, When you Gisable the brake, a screen appears before each race which tells drivers that the brake does not work and to stow down, just take their foot off the accelerator, Disable the brake oniyas a temporary measure, Repair the brake as soon as possible since this is an essential part of the game, To disable the brake circuit, go to the Disable Broken Controls screen in the self-test and choose broken for the brake.

Testing the Switch, Switch Actuator Distance, and Pedal Movement If you have brake problems, see the flowchart in Fig- Malntenance and Troubleshooting

ure 3-9, If necessary, do the following tests to check the switch actuator distance and the switch, 1, Check the actuator adjusunent. The pedal should move at least 1/4 inch before the switch clicks. If not, then adjust the clamp on the white plastic actuator unti] you have 1/4 inch of play in the pedal. The switch must click before you feel resistance on the pexal. 2, Check the resistance on the pedal. {t should begin after the switch clicks, but no further than 1/2 inch from the pedal resting place. If you feel resistance before this point, check if the bearings are moving. If the bearings are moving freely, adjust the nut on the brake spring retum shaft so that the pedal has at feast 1/4 inch of free play, and the switch clicks before the resistance begins.

  • If the pedal does not return to its resting location, check if the return spring is broken or if the bearings are not moving. 4, Check the switch, Disconnect the connector from the Brake PCB and connect an olimmeter across pins 6 anc 7 of the harness connector. If the switch is good, the switch closes when the pedal is nof Pressed, and opens when the pedal is pressed.

Testing the Strain Gauge and Strain Gauge

Bonding

If you have brake problems, see the flowchart in Figure 3-9. If necessary, do the following tests to check the strain gauge and strain gauge bonding. i. Remove the connector from the brake PCB in the

Table 3-7 Troubleshooting the Brake Pedal

Problem Solution | Brake does nat work or is working erratically. . Go through the Set Controls screens in the self-test, |

  • Cheek the F4 fuse on the power supply. Gf this fuse is blown, the shifter wit not work either.)
  • Check the brake force on the 12-bit A/D item in the Control Inputs Screen, As you press down on the brake, the line should disappear, in realtion to how much force you are putting on the brake. 4, Check the hamess connections, . Check the distance adjustment for the switch actuator.
  • Check the switch, a. ‘The connections to the brake snap-tction switch are incorrect, Hamess connections shouidl be on C and NC, , Check the switch with an ohmmeter as described in Checking and Adfusting the Brake,
  • Check the brake PCB. 8, Check the strain gauge by connecting an chmmeter as described in Testing the Strain Gauge and Strain Gauge Bonding. “
  • Check voltage level (o the main PCB. See Table 3-3. 10.1f the brake was not working, and you disabled the brake circuit, bul now the brake is repaired, go to the Disable Broken Controls screen and choose workivig.

3-17

Page 52

Mainteaance and Troubleshoating Reve Oelvin’

“You ha bo Un Conyosscrnons. Golo Convel ypulscsoan In corns

Doos ow Deeg tha Brake Fees tno charge LED co te Bran, ‘wote you oparala PGB wton pe beaks ts ‘te coalror? sinsscd bind?

Check tho ‘Cheek tha comectars 19 he brake ‘Sorrettals am Ino cabin" BORNE and to IN ewe. ‘so tho mai PCB an 9 pin on ter main PCB. Goas tio wloga tal ‘whan tha eaheis proased had, (Chace the powor to bein PCD. ‘hock ma pwn actwalds desanom ‘Chock H 7 Satich ts good and ‘ceenteaird propery. Chock ine avaln guage and tha alraln gavgo bondirg. Tao al dane cesar “Froubloshone tho tReet AD Fieve Orrepiacs Sorvice. cate on lho mah PCS. ‘cables oF connoctors,

Figure 3-9 Brake Is Not Working or Working Erratically and You Have Tried the Set Controls Screens

back of the simulator and put an ohmmeter across 3, Replace the switch with the terminals pointing topins 1 and 2 of the harness conaector. If the ohm- wards the top of the pedal assembly. Adjust the ae meter does not measure 350 2 + 10%, then replace tuatar position so the brake pedal has at feast v4 the brake pedal assembly because the stniin gauge inch of play in it before the switch clicks. Loosen is bad, or tighten the clamp on the white plastic actuator to adjust this distance. The switch must click before you feel resistance while pushing the pedal. w If the ohmmeier does measure 350 Q + 10%, then check the bonding. Attach a digital vol-obmmeter ta pins t and 2 and have someone press hard on 4. Connect the wires to the switch. The two wires atthe brake. If the resistance does net change as the tach to the C and NC terminals. pressure on the brake pedal changes, then the «5 Put the pedal assembly back in the sirulator, Inbonding has failed and you must replace the brake stall the fender washers and the focknuts. Re-conpedal assembly. nect the simulator hamess, . 6. Now switch on the self-test and go through: the Set Replacing the Brake Switch. Controls screens. Before you replace the brake switch, do the Set Controls scteens in the self-test and follow the flowchart in Figure 3-9, Test the switch as explained above in Test- NOTE ing the Switch, Switch Actuator Distance, and Pedal You must enter the self-test and go Movement, If you are sure that you must replace the through the Set Controls screens since switch, cto the following procedure, you repaired the brake, Otherwise the imutator rectly.

  • Turn off the power and unplug the game. simulator will not work correctiy.

2, With the pedal assembly out of the simulator, remove the two nuts that hold the switch against the walt. Take out the screws and the switch.

3-18

Page 53

Race Drivin"

Replacing the Brake Strain Gauge and Pedal Assembly

Before you replace the brake pedal assembly because you suspect the strain gauge, do the Sef Controls screens in the self-test anc follow the flowchart in Figure 3-9. Test the strain gauge as explained above in Testing the Strain Gauge and Strain Gauge Bonding. If you are sure that you must replace the brake pedal assembly, do the following procedure.

NOTE The strain gauge is mounted on the pedat al the factory because special bonding is ftequired. Therefore, you must replace the entite brake pedal assembly if the strain gauge or bonding is baa.
  • Turn off the power and unplug the game.
  • To replace the brake pedal assembly, take off the under-dash cover above the pedal assembly, Use a Phillips screwdriver to remove the screws that holed the cover on the cabinet.
  • Open the lower rear service door. The back of the pedai assembly is above the main PCB. Disconnect the simulator harness from the assembly. Remove the washers and nuts holding the pedal assembly To the cabinet. After you remove the auts, the pedals will hang in the same position,
  • Go to the front of the simulator, Twist and pull the pedai assembly counterclockwise to avoid the bottom of the dashboard.
  • On the pedal assembly, disconnect the strain gauge wires from the Brake PCB. See Figure 3-8 for an iflustration of the pedals. 6 Remove the metal stop bracket with the rubber bumper pads attached to it. Take out the nwo Screws, one on either side, which hold the bracket to the frame. CYou do not need to remove the rubber bumper pads.} Pull the bracket out the assembly.
  • Remove the retaining ring at the top of the brake shaft that holds the shaft and brake springs together,
  • Take off the locking tab on dic end of the pedal pivot shaft. Use a 3/16-inch Allen wrench to remove the socket-head screw.
  • Push the pivot shaft towards the clutch, Remove the brake pedal assembly. 10.Put the new brake pedal assembly into position. Push the pivot shaft through the brake shaft and into the case. Instalt the locking tab and the sockethead screw. Maintenance and Troubleshooting
  • Replace the retaining ring at the top of the brake shaft that holds the shaft and the brake springs together.
  • Replace the metal stop bracket. Put in the nvo screws that hold the bracket to the frame.
  • Re-connect the strain gauge wires to the brake PCB.
  • Check the following 10 make sure the brake is set up properly; a. Check the actuator adjustment. The pedal shouic move at least 1/4 inch before the switch clicks. if not, adjust the clamp on the white plastic actuator untit you have 1/4 inch of play in the pedal. Make sure the switch clicks before you feel resislance on the pedal. b.Check the resistance on the pedal. It should begin sometime after the switch clicks, but no further than 1/2 inch from the starting point. If you feel resistance before this point, check if the bearings are moving. If the beariags are moving freely, then adjust the nut on the brake spring return shaft so that the pedal has at feast 1/4 inch of free play. Check that the switch clicks before resistance begins. 15, Put the pedal assembly back in the simulator. Install the fender washers and the locknuts. Re-connect the simulator harness. 16, Now switch on the self-test and go through the Ser Controls screens.
NOTE Enter the self-test and go through the Set Controls screens since you replaced the brake pedal assembly. Otherwise the simulator will not work carrectly.

Gas Pedal Assembly

The most likely cause of gas pedal assembly failure is the pulley cable breaking or unwinding. Check the Suggestions in Table 3-8 before repairing the gas pedal.

Lubricating the Gas Pedal

Maintain the gas pedal assembly by lubricating at the points shown in Figure 3-11.

  • Turn off the power and unplug the game.
  • From the front of the cabinet, unscrew the seven Phillips-head screws and pull the gas pedal assembly forward. Disconnect the simulator harness from the assembly. Take the assembly out.
  • Lubricate the pivot pin and surrounding area, the

3-19

Page 54

Malnuenunce and Troubleshooting Race Drivin’

fy

ieee Lange Chae at io

1 A ! 8B

Figure 3-10 Rewinding the Gas Pedal Pulley Cable

spring cable, and pulley with dry Teflon spray. Check that the cable is wound correctly. See Figure 3-10,

  • Put the gas pedal back in the simulator and re-connect it to the simulator harness connector. Make sure that the ground wire is connected, Screw in the Phillips-head screws that hold the assembly in the simulator.

Rewinding the Gas Pedal Pulley Cable

The pulley cable may become disconnected during norma] use and must be rewound. If you remove or replace the cable spring, you may also have to cewind the pulley cable. If the cable is cut or frayed, replace it.

  • Tum off the power and unplug the game.
  • Remove the pedal assembly from the simulator by taking out the seven Phillips-head screws that hold the pedal assembly box in the simulator. Disconnect the pedal from the simulator harness.
  • Lay the pedal assembly on the bench, with the extension spring at the front, See Figure 3-11 for an illustration of the pedal.
  • Put the large circular lug on one end of the cable around the hook on the pedal. See Figure 3-10,

3-20 . Bring the cable back through the notch and wap it Step A. Thread the rest of the cable up through the hole in the hase plate. Wrap the cabie counterclockwise around the pulley up to the cap screw. Put the cable through the notch and wrap it once, clockwise, around the cap screw in the pulley. (This screw must be at the top of the pulley, {f ic is not, tum the pulley so itis)

twice, counterclockwise, around the pulley. Do nat wrap the cable over itself. See Figure 3-10, Step B Hook the small circular lug onto the cable spring. The cable spring should be stretched our. Push the pedal a few times to make sure the cable rewmns the pedal to the rest position. . Lubricate the pivot pin, springs, cable, and pulley with dey Teflon spray. . Install the peda} in the simulator and re-connect the harness, Make sure the ground wire is attached. . Go to the Set Controls screens in the self-test and i

i te-inidalize all the controls.

NOTE You must go through the Set Controls screens in the self-test because you repaired the pedal, Otherwise, the simulator wil! not work correctly.
Page 55

Race Drivin?

Replacing the Gas Pedal

Replacing the Gas Pedal Cable Spring

The gas pedal cable spring may break or become Weak, Before you replace the Spring, first make sure the cable is wound correctly around the pulley since this is 2 more likely cause of gas pedal failure.

  • Turn off the power and unplug the game,
  • Remove the pedai assembly from the simulator by taking out the seven Phillips-head screws that hofd the pedal assembly box in the simulator. Disconect the pedal from the simulator harness.
  • Lay the pedal assembly on the bench, with the extension spring pointing up at the front, See Figure +11 for an illustration of the pedal.
  • Disconnect the cable from the cable spring, Remove the spring and replace it. 5, Tf the cable is frayed or cut, replace it, 6 Put the large circular lug on one end of the cable around the hook on the pedal. See Figure 3-10, Step A. Thread the rest of the cable up through the hole in the base plate. Wrap the cable counterclociwise around the pulley Up to the cap serew. Put the cable through the notch and Wrip it once, clockwise, around the cap screw in the pulley. (This screw must be at the top of the pulley. If i¢ is not, turo the pulley so it is.) Being the cable back through the notch and wrap it twice, counterclockwise, around the pulley. Do not wap the cable over itself. See Figure 3-10, Step B. Hook the small circular Jug onto the cable Spring. ‘The cable spring should be stretched out, Push the pedal a few times to make sure the cuble retums the pedal to the rest position.
  • Lubricate the pivot Pin, springs, cable, and pulley with dry ‘Teflon spray.
  • Install the pedal in the simulator and reconnect the harness. Make sure the ground wire is attached, P|

Table 3-8 Troubleshooting the Gas Pedal Assembly Maintenance and Troubleshooting

  • Go to the Set Controls screens in the selftest and se-initialize all the controls,

Potentiometer

Replace the potentiometer if you have followed the flowchart in Figure 3-7 and decided that the potentiometer is the problem. However, when you take the 8as pedal out of the simulator, first check if the springs are broken or if the cable is broken or unwound From the puiley before you replace the potentiometer.

  • Turn off the power and unplug the game, 2, Remove the pedal assembly from the simulator by taking out the seven Phillips-head screws that hold the pedal assembly box in the simulator, Disconnect the pedal from the simulator hamess.
  • Lay the pedal assembly on the bench, with the exfension spring pointing up at the front. See Figure 3-11 for an illustration of the pedal. Disconnect the cable from the cable spring. Loosen the screw on the pulley and remove the pulley from the potentiometer shaft, Take off the potentiometer by removing the nut with a £/2inch wrench. Take the wires off the potentiometer, 6, Put a new potentiometer on the bracket in the base plate, with the three terminals facing towards you and the fiat of the potentiometer sisaft facing up. "Fighten the nut. ?. Solder the harness wires onto the potendometer in this order: red on the teft terminal, white on the middle, and black on the right
  • Put the pulley on the potentiometer shaft and tight en the screw in the hub on the flat of the potentiometer shaft,
  • Put the large circufar fug on one end of the cuble around the hook on the pedal. See Figure 3-10, »

vt

Problem Solution

Boes not return to rest pasition. L

n {Gas pedal dows now work or warks emulically, 1. Go through the Set Controis screen in the self-test,

  • IF that clowsn’t work, see Figure 3-7 for more information.
  • Check the Controf Inputs scecen. If the Bs line does not change as you press the pedal down, then you may need to replace the potentiontter, rewind or replace the pulley cable, or repidce a broken spring.
  • Check voltage tevel to boards, See Table 3-3, Is the gas pedat lubricated? Follow the Procedure under Lubricating the Gas Pedal. Check the pulley cable.
  • Check for a broken extension spring, shown in Figure 3-9,

3-21

Page 56

Maintenance and Troubleshooting Race Drivin’

<i 3 a m3

egatab-Ot = heen Pin E \ cosetoat k Fock Poca Aecoloretar P

1a S| oot \ Pods Comecasalon Spring

, o39703-01 “ “ Cabte Extension Spring’ rf ie oxen H eagasat Rt Pulley i ee a i; ’

Tren Preial Emanston Spring eae 275 SeoHd Cap Serow nvr Foot Pedal Cork 239008-1009 Base Piste 5K Peteemiometor

ems Nat Shown: Foc Paid Grackal Be ROAISST.OT tb Gass Paget Hamoss Atty sro 10-280: F 10-26 Lacknua R THEO FS 480 Washer F) 4 107032-001 Ory Fallon Spray tubreaet #8 pasts shown above make up-the Foe Conrad Assennbly, part Mo. AO29235-3, The Fost Comal Assumbly ln.a Inge sabussembyy at tno Gas Pedal,

Figure 3-11 Maintaining the Gas Pedal

Step A. Thread the rest of the cable up through the hole in the base plate. Wrap the cable counterclockwise around the pulley up to the cap screw. Put the cable through the notch and wrap it once, clockwise, around the cap

3-22 10, Bring the cable back through the notch and wrap i P Ee :

screw in the pulley. (This screw must be at the top of the pulley. If it is not, tum the pulley so itis.)

twice, counterclockwise, around the pulley. Do not : wrap the cable over itself. See Figure 3-10, Step B a p

Page 57

Bace Driven’

Hook the small circular lug onto the cable spring. The cable spring should be stretched out. Push the pedal a few times 10 make sure the cable returns the pedal to the rest position. li. Lubricate the pivot pin, springs, cable, and pulley with dry Teflon spray.

  • Install the pedal in the simulator and re-connect the harness. Make sure the ground wire is attached,
  • Go to the Set Controfs screens in the self-test and re-initialize all che controls,
NOTE You must go through the Set Controls Screens in the self-test because you replaced the potentiometer. The simutator will not work correctly if you do not set the controls.

Replacing a Broken Spring

on the Gas Pedal it is unlikely that these springs will be sprung or fa- Ngued, However, if they are, Follow the instructions below. 1, Turn off the power and unplug the game. 2, Remove the pedal assembly from the simutator by taking out the seven Phillips-head screws that hold the pedal assembly box in the simulator. Disconnect the pedal from the simulator harness.

  • lay the pedal assembly on the bench, with the extension spring pointing up at the front. See Figure 3-1] for an illustration of the pedal. 4, Disconnect the cable from the cable spring.
  • Remove the two retaining rings from either end of the pivot pin and take out the pivot pin. 6 Take out the springs. if you replace the compression spring, he sure dhat the large end of the spring N Maintenance and Troubleshooting

is against the base plate when you put the pedal assembly together again. . Install the new spring and replace the pivot pin.

  • Rewind the pulley cable in the following way:

10.

1t. a. Put the large circular lug on one end of the cable around the hook on the pedal, See Figure 3-10, Step A. Thread the rest of the cable up through the hole in the base plate. Wrap the cable counterclockwise around the pulley up to the cap screw, Put the cable through the natch and wrap it once, clockwise, around the cap screw in the pulley. (This screw must be at the top of the pulley. If it is ner, turn the pulley so it is.) b. Bring the cable back through the notch and wrap it twice, counterclockwise, around the pulley. Do not wrap the cable over itseif. See Figure 3-16, Step B. Hook the small circular lug onto the cable spring. The cable spring should be stretched our. Push the pedal a few times to make sure the cable returns the pedal to the rest position. Lubricate the pivot pin, springs, cable, and pulley with dry Teflon spray before you put the assembly back in the simulator, Install the pedal in the simulator and re-connect the harness. Make sure the ground wire is attached. Go to the Set Controls screens in the self-test and alize the controls,

NOTE You must go through the Set Controls Screens in the self-test because you replaced the potentiometer The simulator wilt not work correctly it you do not set the controls.

3-23

Page 58

Maintenanes ane Troubtestuxming.

Shifter Assembly

IF you have problems with the shifter, check Table 3-9, Troubleshooting the Shifter Assembly. If the shifter is not working but you cannot repair it immediately, you can disable the shifter circuit. When the shifter circuit is disabled, the simulator drives only with the automatic wansmission, even if the driver chooses manual transmission. The driver can shift, but this has no effect. Disable the shifter circuit only as a temporary measure. Repair the shifter as soon as possible. ‘fo disable the shifter, go to the screen Disable Broken Controls in the self-test. Choose broken under shifter. Remember to change chis setting back to working when you repair the shifter.

Installing a New Shifter

Boot

The shifter is shown in Figure 3-13. I. Remove the roi] pin in the kneb using a 1/S-inch punch and take off the knob, 2, Remove the four tamperproof screws that hold the boot cover plate on the shifter case. Lift off the boot and the cover plate.

  • Diseard the beot 4, Replace the double-sided tape in between the holes on the top of the shifter gate. If necessary, also replace the double-sided tape on the shaft where the hole of the boot attaches. . Replace the boot. Install the boot cover plate and the screws. Secure the knob back on the shaft by tapping ia the roil pin. ay

Table 3-9 Troubleshooting the Shifter Assembly Race Drivin’

Replacing a Shifter

Potentiometer

If the shifter acts erratically, follow the Aowchar in Figure 3-12 to make sure that the problem is with the potentiometers. Before you replace the potentiometers, | check that the screws on the ends of the roll link and the pitch Jink are tight but still allow free movement. If ¢ you tighten these screws, do the See Controls screens in the self-test to see if the problem is solved. ‘the shifter is shown in Figure 3-13.

  • Remove the roll pin in the knob using a 1/8 inch punch and take off the knob.
  • Remove the four tamperproof screws that hold the boot cover plate on the shifter case. Lift off the boot, the cover plate, and the shifter gate which has the shift pattern in it,
  • Remove the screw on the tie wrap drat holds the shifter harness on the side of the case. 4, Unscrew the nut on the carriage bolt on the felt side of the case and slip the long thin pitch bar off the bolt.

yw Inside the case, remove the cotter pin on the right side of the pivot shaft.

  • Push the pivot shaft out of the case through the hole on the outside of the cabinet. Use a screwdriver or a pencil. Disconnect the six-pin connector on the simulator harness from the shifter and the wo wires from the solenoid, Lift the shifter assembly out of the case.
  • Test the locknuts on che end of the roll link and the pitch link and the shoulder screws on the thia roll bar and pitch bat, These should be tight but still allow free movement of the har and atuched link. If these are fine, then go to the next steps. Othervise, tighten them, assemble the shifter, do

Problem Soluiion Shifter does not work or works ™ esratically.

Moves in and out of gear freely witnout using the clutch. Shifter squeaks and squeais, Some ncise is normal, If you think the noise is excessive, replace the magnet or the magnet plate, | Go through the Ser Comérois screen in the self-test, Hl . See Figure 3-12 to determing the cause of the problem. . Check voltage level to the main PCB. See Table 3-3. . Check the F§ fuse on ihe power supply. GF this is blown, then the! brake pedat will not work either) H 3, Check the sewing of the shifter option on the Disable Broken Controls screen. If the shifter potentiometer is not working, sel 110 broken and repair as soon as possible. Hf it is working, set the oplion to working, {

Cheek the shificr PCB and magnet.

3-24

Page 59

Race Drivin’

ge ora wilh ha aaor aed yous tiene akaedy Vlad m0 Sat Contm's serean, G0 Lo tha Shae stereon ling in Baws Convert

Cheek His wachanea MaRS Chock the potentiamotors and tne SeeOR 60 the lontinats. Chock the harass ant connections shal 9 a sgh Tha Y-pot ‘ort tho chiter, in tha sritar PER, sista berattas as you bred to Tio Hb AND coeerrtae ret ual ha shah entte mah PCa, Malntenance and Troubleshooting:

NOTE See Chapler 2, Shifter Test Screen, for information about using the shiftar screen in the ern test.

Figure 3-12 Shifter Is Not Working or Working Erratically and You Have Already Tried the Set Controls Screens

the Set Controls screens, and check the results on the Control inpits screen. 8 Ifthe screws and nuts are tight, disconnect the har ness from the potentiometer that you are replacing. Loosen the 6-32 screw of the foil link and slip off the potentiometer shaft. Loosen the nut on the potentiometer shaft with 2 1/2-inch flat wrench. Remove the potentiometer,

  • Solder the harness to the new potentiometer. With the shafi facing you and the terminals pointing down, solder the black wire to the left terminal, the white to the middle, and the red to the right.
  • Install the new potentiometer. Put the potentiometer key in the key sior in the shifter. Tighten the mut,
Page 60

Maimensnce and Troubleshooting

items Not Shown:

BOVT7SI-01 ‘Shier dumpar Assy ‘reano8 B22 xB" Se He. Cap Som

178028-017

Detait of shifter gate

s7oab.0814 48" Dia. x 7/8" Sareng Pin!

Sirasr-ot Pivot Sat Ei

T2101 0F | 4779501 = 10-32 x 5/8" Pan-Ha Seren!) Hinge Wekimem| places) _“inve Wek TTPMO-2 OA78E2-01 10532 Potyme Het one) alent Plate Race Drivin’

UST TaT-Ot Xoo a7em2s-4416) Wee20 x 17 Salt-Locssng| Burt- Hd Cap Screw ta ome

7a-1610F| pelea Baal Ue ee 7 175015-1031] i w #0 Plo Waghot| pity iblo Toe 477010-235] Bewe & hg 6:32 Polymat Hax Lockrnt] Sea neuid tee Reg omndd ort Latch Bearing} iene “ Dovoloaktod Foan z Tape inside fossereas 7} stihor Howning s77010-244| ADATIS-O 44-20 Polymer Hax Lackraa| Hames Assy (2 pisces) 75-35288| 114-20 x ¢ 34" anlage Bet

ced

4548201 Poll Link As Teer 6.82 « 112" Pane Sort 177000-135 6633 Mon Bun

osresa-n1 Eset Delent Lever AolBar Daten Raliar Te EBOt DeTEGE-L B02 Hex SocHd, lover Spacer ‘Snoullar Sere pethebeling 4@ places) Vator 1 144" 9600-40 SooHe. Cop Scrow “Then Lock [y75014-1080, Acasa Flat Waster Levar Spacer ‘auibaae wenen de “14620 Polymer Hex Loctonat 4 Seed, t Exjonion Spring ° 58" Lock Wisshar + 9 17506-1050 PVC Tubing ~ Fine Véashar 7R8010 8.32 x 5B" Soot Cap Sram TTTOONAY | 82.858 DaTss1-01 10-32Hen Nut | 314-200 v2" Salancia! Bund Cap ‘Maunling Pat Seow 49004-0018 Bl eaastppet

  • WAND Salanaia| a 85-1506 nasive sa2raa" 7807-01 Flat Coumersunk Be Spey Tad 1d. Cap Screw s7sareaest E 108007-001 sO Fin Waster “Tevond Lack Adkesing petits 232x746 728808 32 x 12" SOC HE, Sect, Scae! Cap Sere ‘78080801 12 Places] zoe 1780164031 #8 Fat Washo’ 158 Dla, x 787 Sptieg Fie T5043 48 Lock Washi * agen! Detail of Solenoid Maunting Plate

Figure 3-13 Maintaining the Shifter

3-26

Page 61

Race Drivin!

11, Put the shifter assembly back in the case. Attach the pitch bar to the carriage bolt at the top of the tase with the locknut.

  • Attach the simulator harness assembly. Instal) the screw through the tie wrap on the shifter hamess on the side of the shifter case, Connect the vo solenoid wires,
  • Line up the tube for the pivot shaft with the holes in the case for the pivot shaft. Insert the shaft into the case from the driver's side with the cotter pin hole and the slotted end on the left.
  • With the pivot shaft through both sides of the case, Put a screwdriver on the slotted end and curn the shaft untit the holes in the shaft Hine up with the hoies in the tube. Put in the cotter pin. Bo not bend the legs of the cotter pin.
  • Put the shifter gate back on, with the latch and the spring facing down. Replace the double-sided tape in between the holes on the top of the shifter gate. If necessary, also replace the double-sided tape on the shaft where the hole of the boot attaches. 16, Put the boot on, then the boot cover plate. Install the four tamperproof screws. Install the knob and secure by tapping in che roll pin. 17.Go into the self-test and perform the Set Controls screens,
NOTE You must perform the Set Controls screens because you replaced the potentometer Otherwise the simulator will not operate correctly.

Replacing the Solenoid

If the shifter shifts without the clutch pedal being pressed, you may want to replace the solenoid, Shifting without the clutch does not impair the game's perlance, You can replace the solenoid itself as de- Saribed here or order the solenoid assembly (part no. 404830601). Note that in order to remove the solenoid housing, you must remove the shifter housing from the game. The solenoid is shown in Figure 3-13. 1, To remove the shifter housing from the game, first Temove the two screws and the reinforcement place on the outside of the cabinet. 2 Take out the Phillips-head screws on the back edge of the floor trim, which is the strip of metal across the middle of the floor, Remove the three Phillipshead screws atong the front of the simulator under the rubber floor mat.

  • Rum the seat our of the simulator as far as it will ge, Use two screwdrivers to lift and pry up the front comer of the floor, Take out the Moor. Maintenance and Troublestiooting

4, Remove the locknuts that hold the shifter on the Seat assembly frame, Remove the shifter.

  • Remove the shifter assembly from the housing by following steps 1 through 6 in the preceding secton, Replacing a Shifter Potentiomeier,
  • Disconnect the solenoid wires from the hamess. 7 Remove the owo button-head screws from the housing and lift the solenoid mounting plate out. 8, Remove the roll pin to free the solenoid plunger. Remove the four flat screws to remove the solenoid from the plate,
  • Replace the solencic and reassemble following the reverse procedure,

Seat Assembly

The seat assembly has two controls: the magnet, which locks the seat in position during the game and slows the seat movement if the driver pushes the seat out of the game very fast; and the potentiometer, which senses the position of the seat and adjusts the steering wheel force. The steering wheel force becomes lighter as the seat is moved closer to the dashboard, This is so small children, who sit very close, can turn the wheet easily. The seat assembly does not require any regular maintenance, other than checking for obstructions around the seat movement area on the simulator floor and inside on the metal plate the magnet rides on. If you have difficulties with the seat, see Table 3-10, Tronbleshooting the Seat Assembly. Three flow charts help you troubleshoot seat assembly Problems. Depending on the type of problem you have, use the following flow charts: @ If the seats moves erratically, follow the flowchart in Figure 3-7, M@ if the seat does not lock when it should, follow the flowchart in Figure 3-13. @ If the seat locks when it should not, follow the flowchart in Figure 3-14.

Replacing the Seat Rod End Bearings

Replace both rod ends if the seat tums with difficulty, or the seat squeaks as it rotates, The seat assembly is shown in Figure 3-16, i. Remove the four tamperproof screws that hold each end plate on the mounting box. Take off the end plates. Also remove the bottom cover on the mounting box.

3-27

Page 62

Muintenance and Troubleshooting

  • The rod ends are attached to the pivot blocks with shoulder screws, Use an Allen-head wrench and a flat wrench to remove the screws and nuts. 3, Take out the rod ends and the pivot arm, Remove beth rod ends from the pivot arm. Save the nur on the right rod end.
  • Insert the new right rod end into the pivot arm with the nut on the threads. (The teft rod end has left-hand chreads and will not fit on the right end)
  • Carefully set the roc ends and pivot arm length to the following dimensions so that the seat assembly rotates correctly, MThe distance from the center of the hole in feft rod end to the point where it goes into the end of che pivot arm must be exactly 1.25 inches ‘This is for clearance. Wthe clistance from center of the hole in one rod end to the center of the hole in the other rod end should be exactly 11.25 inches.
  • Do not tighten the nut on the right rod end yer.
  • Put the rod ends and pivot arm inte the seat mounting box, with the right rod end on the right side as you face the simulator. Tighten the sockethead screws and nuts to hold the rod ends on the pivot blocks,
  • Turn the mounting box until it is parallet to the front of the simulator. The sides of the seat mount- Mace Drivin’

ing platform should be parallel with the sides of the mounting box too. if they are not, then screw the pivot arm in or out of the pivot blocks until the sides are parallel. When the mounting box and seat mounting platform sides are paralicl to each other and to the sides of the simulator, dghten the nut on the right rod end. Check the alignment a final time. 9, Install the end plates on the mounting box with the tamperproof screws. Put the bottom cover back on.

Replacing Bearings on the

Seat Pivot

The seat pivot bearings urns the seat (not the mount ing box). Replace the seat pivot bearings if the scat twists or jiggles excessively or you can puil the seat up and down. (If both the seat and the mounting box twist and move up and down, the main bearings may need to be replaced.) The seat assembly is shown in Figure 3-16.

  • Remove the tamperproof screws that hold each end plate of the mounting box on the seat assembly. Take off the end plates, Remove the bottom cover on the mounting block.
  • Using a punch, hammer out the spring pin in the seat pivot.

Table 3-10 Troubleshooting the Seat Assembly

Problem sofudon

Action is erratic. 1, Go through the Set Controls screen in the selt-test 2, See Figure 3-7, 3-12, or 3-13 to determine the cause of the problem.

  • Check voltage level to the main PCB, See Table 3-3. 4, Check the setting of the seat option on the Disable Brokea Controls screen. If the seat potentiometer is not working, set it tw broken and H repair as soon as possible. If it is working, set the option to work. ing. Does not turn easily, does act push in and out, or 1. Check for obstructions on the simulator floor and inside the bottom | of the simulator. squeaks. ¢ 2, Check the rod end bearings.
  • Check the shaft bearings on the seat shaft, 4, Check the main seat bearings.
  • Check the gears on the seat assembly. . 1, Go through the Sef Controis screen in the self-test.
  • See Figure 3-12 to find out the cause.
  • Check the APU PCB.
  • Go theongh the Set Controls screen in the selftest.
  • See Figure 3-14 to find our the cause, i 3, Check the APU PCB. t | Scat jiggles or twists excessively, and can be pulled = Does the seat alone do this, or do the seat and the mounting arm jig- | ‘up and down. ale and twist together? If only the seat does it, replace the bearings on + the seat pivot. if both the seat and the mounting arm jiggle, twist, and move up and down, replace the main seat bearings. : Seat does not lock in place when it should,

Seat is focked when it should not be.

3-28

Page 63

Race Drivin’

‘The earl ca locked whan thould be and yous have alraadly tind the Set Conuols scsaen,

‘Partaren tho saat neqnel tast in the Cantrat tngurs eereoe in tho solbiat,

Daoe tho seal locke in sear ‘mapnal ost?

Yes Tansee tho vohage onthe ea) ‘magnet willa you periacm ‘sear mognot fost In thputs in the sal

‘voltage mansura at

rosiewnen wees

mapnet in congact with tha srssgnot plato on Ihe Maintenance and Troubleshooing

Doss the Pos mmouniod on the Pawns Supply. teust 3 Vote?

le tho

‘tha mognot at loast 20?

[a tne-seat

Moar of Ine ‘pane?

Figure 3-14 Seat Is Not Locked When It Should Be And You Have Already ‘Tried the Set Controls Screens

3, When the pin is out of the seat pivot, pull up on the seat and remove it,

  • You will neud to take the seat mounting box to a machine shop to do the following items: a, Remove the old bearings. (They are press fit.) b, Cut down one of che new bearings to 0.6 inch long. This wilt be the bottom bearing. (You can use a bearing on the bettom that has not been cut down, but it may catch someone's foot) ¢. Tum the bearings to the following specifications. WA shaft with a diameter of 1.249 inches should fotate freely in the bearing when a torque of 10 inch-pounds is applied. A shaft with a diameter of 1.254 inches must not fit in the bearing. d. Press the bearings on the pivot of the seat mounting plate. insert the pivor through the new top beuring, the Spacer tube, the pivor block, two washers, and the new bottom bearing. Line up the holes for the spring pin in the seat pivot with the holes in the pivot block. Make sure the seat faces the right direction. Put in the spring pin. You might want to use a 3/8-inch shaft or shoulder screw {0 hold the position while you are putting in
Page 64

Maintenance and Troubleshooting Race Drivitt

The seat ds locked want should ang} be Gnd ya havo alroaady Led tha Sat Coniroie secman,

Dass ine ls tha Yas Isao Ne ot anleck whee: No

sent locked insont tockad when thaS90usae yor‘Chock the saat louse Bwich
herpaver it otf?pase oot‘adtha wich homed,

made? —

a Yes Yes

Porarm ihe sat magnet Last‘Dheck far abarevesions aroundPortarm tha sont magnat tas I
Inte Conta? inputs Inthemastfoncanturdenttho Gonna? fapate screen in the:
bidenBearogs. tho goars, aad all thafaaslaiae

shat baarogs,

iNo| Chack the smar magnet conradThe peatRe| Check the vous magast cotrot
seat releases in tnoSraiten the APUPTB.relansee in the sentiret on tha APU PCH mountot
‘woot magnetmmouriext on tip Pawar Supply‘magnet‘an tha Peasy Supply

test. = Yos

Yes I No Na le she el Fi wood? Thee Tot coution? afore eae the sooe, on che magnet pare, tho 70d end botrings, the gear, and af tie chart boatags. ves

Yes. Yes

‘Check seat contral vattsge ‘Thock seat contol output an ouigalon the main PCB. the maln PCB,

Dass the ‘seat stloase switch work right? $0] chock tia cast retaasa eweten Reepiaen oc repalr tha Replars ar rapa the ‘era tha waitch harnaes, APUPCE. APU POR,

Goto the Rewchart in Figure 3-7,

Figure 3-15 Seat Is Locked When It Should Not Be

And You Have Already Tried the Sef Controls Screens

3-30

Page 65

Race Deivin*

the spring pin.)

  • Make sure the pin is flush with the outer edges of the pivat biock. 8 Put the enc plate back on and install the four tamperproof screws in each plate.

Replacing the Main Seat Bearings

The main seat bearings are located between the base of the simulator and the seat mounting box, Replace them if the seat mounting box is twisting or jiggling or you can pull the box up and down. (if only the seat twists and moves up and down, the sear pivot bear ings, not the main bearings, may need to he replaced.) The seat assembly is shown in Figure 3-16. To teplace these bearings, remove the simulator floor and take out the seat assembly. You will need someone to help you, 1, Take out the Phillips-head screws on the back edge of the floor trim, which is the strip of metal across the middle of the floor. Remove the three Phillipshead screws along the front of the simulator under the rubber floor mat.

  • Tum the seat our of the simulator as far as it will §0. Use two screwdrivers to lift and pry up the front comer of the floor. Take out the floor.
  • Before you can take out the seat mechanism, take ‘out the coin module and the shifter. Open the top and bottom coin doors and take off the four lock- Aus on the carriage bolts on the side of the cabinet, 4, Disconnect the hamess from the coin module, Remove the bolts and the coin module. . Now take out the shifter, Loosen the self-locking screw in the shifter knob and take off the knob.
  • Remove the four tamperproof screws that hold the shifter boot cover plate on the shifter case. Lift off the boot, the cover plate, and the shifter gate. Disconnect the shifter harness. ?. Take off the locknuts on the two tamperproof screws that hold the shilter on the side of the cabinet and remove the screws. 8 Remove the focknuts that hold the shifter on the seat assembly frame. Remove the shifter,
  • Disconnect the simulator harness from the seat assembly. Remove all the screws and nuts that hold the seat assembly in the simulator, Tip the seat back until the seat frame clear the floor, Push the seat assembly towards the pedals until the assembly is out from under the floor. ue Maintenance and Troubleshooting
CAUTION The gears and potentiometer are on the botiom of the assembly under the floor in front of the license plate, Do not damage these parts when you push the seat assembly forward and up.
  • When the assembly is clear of the floor, pull the assembly out of the simutator.
WARNING Ths seat assembly is heavy. Be careful.
  • Remove the four tamperproof screws that hold each end plate of the mounting box on the seat assembly. Take off the end plates, Remove the botfom cover on the mounting block.
  • Remove the rod ends and the pivot arm from the pivot block inside the mounting box. The rod ends are attached to the pivot blocks with shoulder screws, Use an Allen-head wrench and a flat wrench to remove the screws and nuts. Take out the rod ends and pivot arm and lay the assembly aside.
  • Remove the potentiometer bracket with the potentiometer gear and small gear from the bottom of the seat assembly.
  • Remove the large half gear on the bottom of the main shaft. You may want to tum the assembly on its side to do this. 15, Using 2 punch, hammer out the spring pin in the bottom of the main shaft in the magnet arm. Remove the magnet arm.
  • Turn the seat until you can pull the seat mounting box off the seat assembly Frame. 17, Take the seat assembly frame to a machine shop to do the following items: 2, Remove the old bearings, (They are press fit.) b, Turn the new bearings to the following specifications. WA shaft with a diameter of 1.624 inches should rotate freely ia the bearing when 3 torque of 10 inch-pounds is applied. . A shaft with a diameter of 1.629 inches must not fit in the bearings. ¢. Press the new bearings into the seat frame.
  • Insert the main shaft through the top bearing, the shaft holder, the bottom bearing, and the magnet arm.
Page 66

Maintenance and Troubleshooting

  • Line up the hole in the shaft for the spring pin with the hole in the magnet arm. Make sure the seat faces the right direction. Install the spring pin.
  • Put the rod ends and pivot arm assembly back into the seat mounting box, with the right rod end on the right side. Tighten the shoulder screws and nuts Co hold the rod ends on the pivor blocks. Da not install the end plates or the bottom caver on the mounting box until the seat assembly is in the simulator, . Install the potentiometer bracket Gghtly on the bottom of the assembly.
  • Tum the small gear on the potentiometer shaft unti] its set screw is directly below the center terminal on the potentiometer.
  • Turn the seat so that when the large half gear is installed, the Rat edge is opposite the small gear and is parallel to the sides of the assembly. Install the gear. Tighten the screws well. 24, Lift the assembly into the simularor. Push it forward and then back to ease it into position, under the ficor. Be careful not to damage the gears and the potentiometer, 23, Install all the screws and nuts that hold the seat assembly in the simulator.
  • Reinstall the coin box and re-connect the harness.
  • Put the shifter back in the simulator. Put the locknuts on the tamperproof screws and the carriage bolts. Re-connect the harness. &

28, Put the shifter gate back on, with the latch and the spring facing down. Then put on the boot with the foam cushion and install boat cover plate over the boot, Install the four tamperproof screws in the cover plate. Install the knob. 29, Re-install the floor. Put in the screws in the front of the flaor and in the metal Roor trim,

  • Turn the mounting box until it is paraltel to the front of the simulator. The sides of the seat mounting plavorm should be paratlel with the sides of the mounting box too. If they are not, then screw the pivot arm in or out of the pivot blocks until the sides are parallel. When the mounting box and seat mounting platform sides are parallel to each other and to the sides of the simulator, tighten the nut on the right rod end. Check the alignment a final time.
  • Install the end plates on the mounting box with the tamperproof screws. Pur the bottom cover back on,
  • Enter the self-test and go through the Ser Controls screens.

3-32 Race Drivin’

NOTE You must go through the Set Controls screen in the self-test because you re- Paired the seat assembly. If you do not do this, the seat will not work correctly.

Replacing the Gears on the Seat Assembly

If the seat is not turning easily of does not tum ar all, do the following: @ Check for obstructions on the simulator floor. W Check for obstructions on the magnet plate below ie floor, Do the following:

  • Take out the Phillips-head screws on the back edge of the floor trim, which is the strip of metal across the middle of the floor. Remove the three Phillips-head screws along the front of the simulator under the rubber floor mat.
  • Turn the seat out of the simulator as far as it will go. Use two screwdrivers on the front comer of the flaor co lift and pry the Roor up. Take out the flaor. 3, Check for obstructions on the metal plate. @ Check the rod end bearings to make sure they are turning. I Check for broken or missing gears. Lift up the simulator or turn it on its side, with the seat high, and Took through the hole in the bottom of the simulator at the gears.
WARNING This simulator weighs 750 pounds. Be extremely careful when you lift it, turn it, or work on it $0 that i Goes not fall.

Look in the hole directly underneath the main seat shaft, You should see two gears. The small gear is mounted on the potentiometer. The large gear is mounted on the bottom of the main shaft. If the gears are broken, cracked, or missing, you must replace them.

Replacing the Small Gear

  • Remove socket-head screws which hold the porentiometer bracket in the simulator and pull the potentiomerer bracket and the small gear a lite ways out of the simulator, See Figure 3-16,
  • Loosen the smail set screw on the smail gear hub.
Page 67

Race Dulin’ Maintenance and Troubleshooting

items Not Shawn: ADABSIAA0T Saat FloxHamass Acsy. ‘178100-006 a750120165 1.25" LO. Bearing & 0.0, Washer {Z pisces} oasge1-oT ‘Tavs tperwann fives block & uppor s7enan2s28

Dosaring énBaan motanueg boa)1.95" Spaleg Pin;

AD$8333-01 Sost Hames ‘Yose07-001 Thebad Lock Antiasiee reso 4640404 $1818 x25 Seat Hax-Hd. Serow 75085 ‘Spel Lock Wasthor 1750141058 Flat Vfasher

aTr0zs-0ctxeeMountingPato096387.

eal Mountirg Patton

72.562010" Toggee Nut:paar
$420.4 1.257s-0ToIR.ca:“ee

178100-007 Bor

Haetd Serew | wa FengerWasher|a5£9LO. Beating
75-0488728808iae2 piacos)cereeaet
‘Spl YeasnerVENTeepamnicee —) Meuning ox

. End Plate Fewer |e Popk Teoos Bod End ? 1720176149 | 472021-006

(a8" Hex Nut| Feght Rod End

zi 177000149

z“ipeesee.oy| E24 Hox Mut

} Seat Pivot Arm 5 972021-066 08 Rod End

1720174816Iel—

ed Eid ‘Smoukior Screw 04636001 ey ousoeean

Piet BlockEeevet18008-1003

SK Posantiamalor 7685208 oreaes-at

casrage BohFretPot Beackan

print ety 24-Tosth Gear #4" Losin 725008 75.0185 10-32 x 7 Hax Fla! Washoe! Seed Cap Serow 750409. erred 1G Lock Washer sOGx ‘Tamperprvot Sorew 17200-2898 Ox6986-KX 2.25" Sprtag Fin Sent Assy. Frame 0e8g62-01 wee 1092 x 112" Hex Soe

Magnet Bumctat483610Hii, Cap Screw
MBITMagnet Pivot Bracket76-0405
Magnet17287-4828#10 Spt Lock Washoe
waneSNBABX 1.75T7SO1S-1040
egez178Suaietoowete GaurMOWnchor

Pan-Ha Screw AFTON paenbegieed SAB-18 Leehnun 28:22 Locka

Figure 3-16 Maintaining the Seat Assembly

3-33

Page 68

Maintenance and Troubleshooting

‘Use a 3/64-inch Allen wrench. Pull off the gear. » Tum the potentiometer in the bracket until the flat of the potentiometer shaft is directly below the center terminal. . Install the bracket in the simulator. Make sure the socket-head screws in the bracket are tight so it will not fall off. . Tum the seat so that the flat edge of the large half gear is opposite the potentiometer and is parallel to the sides of the simulator. . Install the new gear on the potentiometer shaft. Do not tam the shaft while you are putting the gear on, Put Loktite on the set screw. Tighten the set screw. . Put the simulator back on the floor. Go into the self-test and perform the Set Conirois screens.

NOTE You must go through the Set Cantrofs screen in the self-test. ff you do not do this, the seat will not work correcily.

Replacing the Large Gear 1. ‘Turn the seat so it will not move. 2, Remove the two socket-head screws holding the large gear on the main shaft, Take off the gear, . Install the new gear, Make sure that it meshes with the small gear. Tighten the socket-head screws 50 the gear will not fall off. . If the seat did not tum or move while you were replacing this gear, you are done. If the seat did move, do the following: a. Take out the potentiometer bracket. Turn the small gear until its set screw is directly below the center terminal on the potentiometer, b. Tura the seat so that the flat edge of the large half gear is parallel to the front of the simulator and is opposite the place where the potentiometer bracket is installed. ¢. install the potentiometer bracket in the simulator. Make sure,the gears do not turn from the position they are set in. Tighten the socket-head screws on the bracket. d. Put the simulator back on the floor. . Go into the self-test anc perform the Ser Controls screen.

3-34 Race Privia*

NOTE You must go through the Set Controls screen in the self-test. if you do not do this, the seat wilt not work corractly.

Replacing the Magnet on the Seat Assembly

Before you replace the magnet because the seat does not lock, go through the flowchart in Figure 3-13 to make sure the magnet is the problem. ‘You must remove the floor as described in steps 1 and 2, below, to get access to the magnet.

  • Remove the Phillips-head screws on the back of the floor trim, which is the strip of metal across the middle of the floor. 2, Remove the three Phillips-head screws along the front of the simulator under the rubber floor mat. Turn the seat out of the simulator as far as it wilt go. Pry up the floor using two screwdrivers. Remove the floor. 3, Tum the seat so you can see the magnet. The magnet is attached to the arm by a bracket that permits the magnet to move freely. Check the harness © the magnet.
  • After going through the flowchart in Figure 3-13 and determining that the magnet must be replaced, do the following steps.
  • Unserew the two Phillips-head screws that hold the magnet on the magnet bracket and disconnect the harness,
  • Discard all the hardware that came with the new magnet and install the magnet with the Phillipshead screws and nuts. Re-connect the hamess.
  • Re-instali the floor. Insert the screws that hold the floor and the metal Moor trim in the simulator.

Replacing the Seat

Potentiometer

Replace seat potentiometer if you have tried the Set Controls screens, you have followed the flowchan in Figure 3-7, and you are sure the problem is the potendometer. (if the seat does not lock or locks when it should not, the problem is ofthe potentiometer.) If you cannot repair the seat immediately, you can disable the seat potentiometer circuit, Read about what the seat potentiometer circuit does before you disable it with the Disable Broken Controls screen.

Page 69

iy

lianas Ruce Drivin’

The seat potentiomerer senses the location of the seat which determines the steering wheel force. The closer the seat is to the dashhoarel, the lighter the force is on the steering wheel. This is so small children, who sit very close, can turn the steering wheel easily. if you disable the seat potentiometer circuit, the steering wheel force is light in all positions. Cf the Steering Wheel Force in the Geme Options screen is set co medium (he default) the force will be light, If it is set 40 light, the force will be very light.) Operate the simulator with the seat potentiometer cir cuit disabled only @ temporary measure. Repair the Seat potentiometer as soon as possible. Disable the circuit by going to the screen Disable Broken Controls in the self-test and choosing broken under sear pot, After you repair the potentiometer, remember to choose working again. The potentiometer is mounted next to the end of the main shaft on the seat and has soldered connections. The seat is shown in Figure 3-16. To replace the potentiometer, turn the simulator on its side or securely prop up the front of the simulator. In either case, you wiil need help, since the simulator is very heavy, You may finct it easier to work on the simulaior by turning it on its side, with the corner with the seat shaft high,

WARNING This simulator weighs 750 pounds. Be extremely careful when you iff it, turn it, or work on it so that it does not fall.

» In the hole directly underneath the main seat shaft, you can see two gears. The small gear is mounted on the potentiometer in the potentiometer bracket. Remove the socket-head screws that hold the potentiometer bracket in the simulator and bring the potentiometer bracket our of the simulator. 2 Loosen the set screw on the small gear hub. Use a 3/64-inch Allen wrench,

  • Loosen the locknut on the potentiomecer shaft and take the potentiometer out of the bracket. Take off the harness wires, Leave the ground wire attached to the bracket. 4, Put the new potentiometer in the bracket, and put the key in the hole in the bracket. The connectors should be on the same side as the ground wire bracket. Tighten the nut on the shaft,
  • Bend the potentiometer connectors up, but not so they touch the bracket. Solder the black wire near est the ground wire, the yellow wire in the middle, and the red wire on the other side,
  • Install the bracket back in the game. ‘lighten the Maintenance and Troubleshooting,

socket-head screws on the bracket so it will not fall off, ~

  • Ture the potentiometer until the flat of the potentiometer shaft is directly below the center terminal.
  • ‘Pur the seat so thar the flat edge of the large half gear is opposite the potentiometer and is parallel to the sides of the simutator.
  • Install the new gear on the potentiometer shaft. Do Not turn the shaft or the seat while you are putting the gear on. Put Loktite on the set screw. Tighten the set screw,
  • Put the simulator back on the floor.
  • Go into the selftest and perform the Set Controis screens.

Video Display

If you have problems with the video display, check ‘Yable 3-11, Troubleshooting the Video Display, before you remove the display.

Removing the Video Display

Perform the following procedure to remove the video display. (See Figure 3-16.)

  • Turn the simulator power off, but leave the power cord plugged in. Wait two minutes.
WARNING High Voitage The video Gisplay contains lethal high voltages. To avoid injury, do not service this display until you observe all precautions necessary for working on high-voltage equipment, X-Radiation The video display is designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never mociily the high-voltage circuitry. Implosion Hazard The cathode-ray tube may implode if struck or dropped. The shattered glass from the tube may cause injury up to six feet away. Use care when handling the display.
  • While you wait, remove the six screws that hold the smail top service panel on the simulator.
  • Disconnect the simuiator harness to the attraction sign. Remove the large outside panel that the at-
Page 70

Maintenance and Troubleshooting

traction sign is mounted on by taking off the carsiage bolts that hold the panet on the simulator.

  • Discharge the high voirage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make cemnain, always discharge the display as follows: a, Attach one end of a solid 18-gauge wire to a well-insulated screwdriver or wooden handle. b, Attach the other end of the wire to an earth ground, ¢, Quickly touch the blade end of the screwdriver to the CRT anode by sliding it under the anode cap. d, Wait two minutes and repeat step c.
  • Disconnect the harness connectors from the video display.
  • Remave the motor amplifier assembly from the cabiner side.
  • Remove the four screws and washers that hold the video display on the shelf.
  • Pull the video display out of the back of the cabinet.
WARNING When you take the video display out of the cabinet, do not drap it! The display is heavy. Be carefull Wear gloves to protect your hands from the sheet-metal edges.
  • Replace the video display as described in the following procedure.

Replacing the Video

Display Perform the following procedure to replace the video display in the cabinet. (See Figure 3-16.} Race Drivin’

NOTE Before you replace the disptay in the simulator, clean the screen and the inside of the shield. Carbon particles from the motor collect on the surfaces and obscure the view.
  • Carefully lift the video display onto the display shelf in the cabinet.
NOTE When you replace the cathode-ray tube and yoke together, adjust the brightness, size, and ceniering as described in the video display service manual. Check the purity and convergence according to the service manual insiructions, but adjust both only if required.
  • Position the display so that the four holes in the video display mounting brackets line up with the four holes in the video display shelf.
  • Loosely install the four hex-head screws and washers through the mounting brackets and into the video display shelf.
  • Push the video display forward against the bezel. 5, Be sure that the display is centered horizontally in the bezel. Tighten the screws.
  • Install the motor amplifier assembly on the side of the cabinet.
  • Connect the harness connector to the video display.
  • Replace the large and small rop service panels.

Table 3-11 Troubleshooting the Video Display

Problen: Solution, Any problem. ‘Determine if the problem is with the display or the. simulator hard. ware by performing the selftest. If you cannot perform the self-test, use the DIP switch diagnostics to narrow down the source’of the problem. Check the voltage level to the video display PCB, Check the video display settings with the Monitor Test Screens in the. selFiest. Convergence, purity or color problems.

3-36

Page 71

Race Drivin" Maintenance and Troubleshooting

Flaca Orie few: View ADATTSE-CI D

Figure 3-17 Removing the Video Display

Motor Amplifier Assembly Removing the Motor Amplifier Assembly

1, Tum the simulator power off, but leave the power cord plugged in. Wait two minutes.

WARNING The PCBs in this assembly contain lethat high voltages. To avoid injury, do not remove the assembly until you observe aff precautions necessary for working on high-voltage equipment.
  • Unplug the power cord.
  • Take off the harness to the PC boards. 4, Remove the entire assembly from the cabinet, Do hot remove the PC boards from the heat sink. . Send the entire assembly back to your distributor for trade-in.

Speakers

if you have problems with a speaker, check Table 3-12, Troubleshooting the Speakers, before you replace it. we

Removing a Speaker

  • Tur the simulator power off. 2, Remove the dashboard, following the directions in the section Removing the Dashboard.

3-37

Page 72

Maintenance and Troubleshooting, Race Dalvin”

Table 3-12 Troubleshooting the Speakers Problem Solution No sound Make sure the volume is tumed up, ¥ the volume is tumed up, clo the following: Do dhe selFtest to make sure you do not have a sound PCB problem. Check the voltage level to the sound PCB, Check the wiring. Replace the speaker if defective. |

the main PCB. If none of the above work, the problem may be on the APU PCB | i}

CAUTION 8e careful when handling the speaker. The cone material is fragile and can be easily damaged.
  • Remove and replace the speaker. 4, Insta)] the dashboard, following the directions in the section Jnstalting the Dashboard.

PC Board Stack

PC Board Stack Removing a Board from the

Pour PC boards are stacked in the following order Gop to bottom) as illustrated in Figure 3-18; @ the Sound PC board Wi the DSK PC board M™ the ADSP IL PC board Mi the Main PC board The boards are attached at uke corners. Some of the standoffs are permanently attached to the corners; da not try to remove them

  • Turn the power off and remove the bouom service door at the back of the simulatar,
  • Remove the board stack from the simulator.
  • Remove the four.2-1/2 inch screws from the corners. of the Sound PC board on the top of the stack. 4, Disconnect the harness and all ribbon cables,
  • The DSK PC board is a short board attached below the Sound PC board. To detach the DSK PC boar, remove the two 3/8 inch screws from the top center of the Sound PC board.

3-38 Replacing Static-

Replacing Static Sensitive Devices

Be careful when you work with static-sensitive devices on the simulator PCBs. These devices can be micro processors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology, These devices can fail from 2 static charge that has built up in your body. They can also fail because of leakage from an improperly grounded soldering iran. Before you handle a static-sensitive device or a PCB with such devices attached to it, ground any static voltage chat may have accumulated in your body by touching an object that is earth-grounded. If you sol der a static-sensitive device, use a soldering iron with a properly grounded three-wire cord. Before you replace 2 static-sensitive device, make sure that the device actually is defective. A static-sensitive device can appear defective due to leakage on a PCB. To check if a device is defective, ground any static voltages as described in the paragraph above, Clean both sides of the PCB with flux remover or an eraser, For discrete FETs, clean thoroughly between the gate, drain, and source leads, ‘Then test the device. A new static sensitive device may be packaged in conductive foam or may have a protective shorting wite attached to the pins. Remove the conductive foam just Prior to inserting the device into its socket or soldering it to a PCB. Remove the shorting wire only after the device is inserted into its socket or ufter all the leads are soldered in place.

Page 73

Race Drivin’

479171-1816, 632x107, 144" exe ol €# Pracoa): 17817-1836 2.x 1.0" Round Suances Maintenance and Troubleshooting

Hams Not Shown:

aAnsT 16207 PCB Ribbon Cable Aggy, ADEE PCB Intprenanmer RUNES Atty. {Bier ar Fe8 Assy

37821838 Gx 14" Sat. inching Space| AnaToab-0x Denver ADSP II PCE Assy, og eencincting Sever ‘i (4 Paresh ADSTT2401 Dever OS PCH Assy,

721806 BOR 28" Pant. Scien (4 Piacasr ADMGADL OT ‘Diver Sound PGB Assy, Sra, TR1000P raoits| fey See ray Panta, Serow 4 Lock Wagner (8 Paces) (4 Pisces} el 3750101025 5 Lock Washor 185 x.132 Flan Washoe Ta BsF G2 Places) ia E9242.90 Pantie, Som | 375056- 1025 & Proces} 2S A Pe wrestr 72005 ea Paces rrazsses: L7~_| #821 0 so cintng Se | I Ghee 2 Piaaes) resar4.s085. 156 x 212 Fiat Warter 4 Pancas)

Figure 3-18 Disassembling the PC Board Stack

Cleaning the Coin Mechanism

Use a soft-hristled brush to remove loose dust or foreign material from the coin mechanism. Use a toothbrush to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out the dust with compressed air.

Cleaning the Interior Components

Perform the following procedure to clean the components inside the cabinet. “L Open the smail top service panel and botiom service door.

  • Discharge the high voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows:
WARNING Turn off the AC power, but do not unplug the power cord before cleaning inside the cabinet, The power cord provides a ground path for stray static voltages that can be present on the cleaning tools,

a.Attach one end of a solid gauge wire to a wellinsulated screwdriver or wooden handle. b.Attach the other end of the wire to an earth ground. . Quickly touch the blade end of the screwdriver to the CRT anode by sliding it under the anode cap. <¢. Wait two minutes and repeat part c, Use a vacuum cleaner with a soft iong-bristled lbrush attachment or use a soft-bristed paint brush fo remove loose dirt and dust accumulated on the inside of the cabinet. Be sure to clean the power supply, PCB assemblies, and video display thoroughily.

CAUTION Be extremely careful when cleaning the electrical components inside the cabinet. Do not touch the electrical components with any solid object other than the soft bristles of the vacuum attachment or Paint brush,

3-39

Page 74

Malntenance and Troubleshooting

N

3-40 O Race Drivin’

Page 75

CHAPTER 4

Illustrated Parts Lists

PART ORDERING INFORMATION

This chapter provides information you need to order parts for your game.

The parts lists (except for the PCB parts lists) are arranged alphanumerically by Atari part number. All A-prefix numbers, which are assemblies, come first, Next are Part numbers with six numbers followed by a hyphen (000598- through 201000-). Ending the Hist are part numbers with a ewo-number designation followed by a hyphen (00- through 99-).

The PCB parts lists are arranged in alphabetical order by component. Within each section the parts are arranged numerically by part number.

When you order parts, give the part number, part name, the number of this manual, and the serial number of your game. With this information, we can fill your order rapidly and correctly. We hope this will create jess downtime and more profit from your games.

Alari Games Customer Service phone numbers are listed on the inside front cover of this manual. © @SHOSGSOSBSSBSS PSHSASHSPSSHSSSSHO

Page 76

Mlustrated Parts Lists

aDTr9601 i Syne Aszy. i ‘See Page 613 FT i i 1 Hl

orotorria
Pig Campypoety
Heer)roty
30 12 LW Semritt
(2 placedtouogg
V7HDPTO98640108roytd
abr 3a"LP Some teh Wecow Geen!1]tt
oTcrm|jtott
foisCoryDreeseh Curcoreeat |1!||

H H hut rod riot i al ft

Oe 1-14 & es Seen Geese carrot Bite? ee ee ee = ae Race Drivin’

wren spanerore Carey 10 Westar Tithao ea PEW, Gli fieueae LDWY Sewer Foam Tape 2e11z8 Teaeioo fsayane tS placos) (A plneaay cnoeat Sioeitiere —srmaconse wane Bes Ves = Coram bt oe ‘aur aa ieaal Tress | ES er ter fe places) ieee Bion 14" Wewenal Panty font pot var 4 pezces?

shoe

‘Spring Mv‘:

14 peers} Pig Coe shawou < rey Fe wait a ir UaTONAaT sae 5 ete Pe ae

14-20 Haw NutCarine BitsATOZ
rmarepeat9a.q Dba Sew
BONE BIOSpritTHO s 1.75aaa

2 oA Cineerpe Boa Canch & Brake Peau Aes [Pert ‘(See Fagus 47) Re eld ! wien pee) | ' Pot e251 ue 27 Canton eat: : impar arena | 140 Hae 178920-220) wart xe SueW

Figure 4-1 Cabinet-Mounted Assemblies, Front View A046250-01 E 18006-109 OK Poeanaiomenee enene-zat ‘Shey Sten 60382.001 Puctrtition Seb ‘ostoatr Cath Bon sriezron Coke Boar

Page 77

ai20 Nae Rig Bucd tat Fendt Weaebor Reason

ee fd a7

636 0138 Movil Seer sta 81078] esses Hees Saree] ‘Teoroa2 (@pico We Femiss Washers 7eaT. 1056) Gs eiaces) 945° Fue Washes vio epee 1:20 Spring 354455 Togaweiny vie CAs) aah abet spews) yessD 4204125 " Host Sowa! é 60455 ge Wa" Lock Washor fe ie re 41050 me ‘wa" Wosbee te

rrsg.a-1050 a" Washoe TIO 4-20 Low Ceaven BISER Mus essa crue n mom peo herwawaaib nant avian wad Caen nr

i

THO

anecata. Bplsors} 1 Pl ay soma

X34" LEW Sut i? gesees) v Seat Ay. (800 Poe 427 vrbaisad #99 $9 Pavits, Som pty 1739183080 18299 Pests thay apum 412 shares} wematatone — cimete Eland {1 eaas) 7665208 17914-1910) Carona teh seq Fan Washer| {4 paces 725500 (Soe Faas ahh pe Ne wa2tn 128 Besos! vee Hd, Seven | ‘@elaees ‘7E-Oass | ‘ua Spa Wai {td plocas] owsrzo1 ') ‘Seat Saks | i: Miccdmaned " rarer ose ‘és plesas)| 76025-4106 #192195) remar2 Butld. Cap Sera (5 piscot!| TOSSA 20 Tape [homs not Sawn: ADesrO5-01 Fan Cad Ang. ADAIEOT Atrmction Hamena Assy. ADATTeet Nan Hamess Augp, Aamasa22} Power arrose Assy. ADeSI2301 (AD Warren Assy. ADS ci Rareaas 2a Angers Mor veercorrvet Wameas Assy. Llasact al POA Imerconnel Hureass Ay, anoasaset ‘anes Foe Cate Aany. anseracnn Mote Patton Catia Asay. Avermear PCR Ribbon Cable Assy. AONE Componert Bracket amass Assy. massac “ep Fgh Ceca Pal ‘Lefl inner Decal wodar.a04 412 Spasar ‘atscest 78003-1649 46468 Pam Serew (8 ptecos) anes, soar Pankd Sew ‘2 piacne) VIDI26-002 $92 Tampransue! Hire Drie oxen Shock Warning Labes panesz01 FS emng or8as0-02 FOC Copiers Labo indinael ‘Product 0. Labal y79001-003 3x5 Prest-Sosi Bag Min cnned Wire & Gable a s7e0rseo1 ‘Supe ST SateTodt Label

Figure 4-1 Cabinet-Mounted Assemblies, Front View, Continued. A046250-01 E IBustrated Parts Esis

4-3

Page 78

Ukustrtted Parts Lisis

175014-3040 Rawe Drivin’

EMH2-112‘75014-3040
#19 Fal Vasher— Video Display Gazal#30 SooHd Straw p10 Faas
{3 places)‘1780S6-002TTINA04DBrey
O2-41168Fearn Tape,#10 Flat Washeried fren

a Buta. ar ‘op Scrow EZ7-OT

@oalacastI7SNE3080)Canine Canopy

sra2eoane 114° Pan Wah Fares Foon Tay 6221168 #10 Soe-Ha. Sctirwy

37827001‘reas ate12¢ms.00t
Achetive Foam |Spay StiFoam Taps{io Dipl

| eA

$ 1H" Lack Wlaghor 178014-1650 Va" Pat Waster I76015-110

F024 x 4.0 Hex Serew ee Sa @ places} IROS-110 2 10% 59 Pan-tid, Seow

OSFTD1-G2>olie(2 ptocas}
.Bottom Fight Decal7511060
ares|_rreaeona_sBCG Fin Wreshr
‘SiGoCaneaar(2 pisces}

Ps 5 | reo

*.,-oe a10: Tevet Woshor
W60Z220ae.(2 pleas)
Ba 1-06 LPW SoreW1dez-caTADSINIDOS § 176015-110
4 ptacaspanaletonONOFF#10 Soow
«|poeanaraera08-00
TessaAosasT?-o1ease eaeFen Biase Gussd|iensen tess (2etscee
1M" Hows. SerewBrake PCB Ascy.{See Flgwre 4-53)TIGHFBea NU Washer
emeas|(See roaC1017812040696.32 Socaw
75-0702PCH Standott7698516ADSTTSO-NS
Asa* Pend, WasherFoot feast ‘covet6 Nhs WasherUnk Agsy,
(places)ereenry‘$7seao-2
oatinedonezs0-0fTETWROORAGID1TIOOR- TOS1740S| AX ALPE SO
Pedal Mounting weknareTSOASSBemam Service Doorfeeonnees80"Abe wasner Foes Washerf (2,
M4 Split Lock WasherOs7t0843Board Soi Asay, Pan Hee Sere[232 places)
#3 pisces)Laver Rar Pant Oecd — (San Figun rt)plces)eparsior

Product |.G. Labet

Figure 4-1 Cabinet-Mounted Assemblies, Rear View A046250-01 E

Page 79

Race Drivin" Illustrated Pans Lists

Cabinet-Mounted Assemblies Parts List

Past No.DescriptionPart No.Descripdon
AD43705-01124tnch Fan Cord Assembly175014-1040#10 Washer
ADS3910-01On/Off Harness Assembly75-99511#10-24 Nut/Washer Assembly
AQ43932.02Shifter PCB Assembly (See Figure 4-13)8281085¥10-24 x 1/2-Inch Butt-Hd. Blk Screw

A044431-01 APY PCB Assembly (mounted on Power

Supply Assembly} (ee Figure 4-12)AO47760-01Cabinet Assembly
A044817-01Brake PCB Assembly (mounted on ClutchAO4779G-08Shifter Assembly (See Figure 6-6)

and Brake Assembly) (Sex: Figure 4-14)

4045193-01Motor Ampilifier Assembly038096-01Shock Waming Label
A045968-08-Race Drivin’ Main PCB Assembly’ (See039091-0%Cash Box
Figure 4-11)046255-01Coin Box Shroud
AG46251-01Shipping Container Assembly046278-01Front Floor Pane? (for Seat Assembly
AG46253-01Coin Box Assembly8046355-01)
ADSE3}4-01Program Phig Assembly046280-01Boutom Service Door
AN6322-01Power Harness Assembly046282-01Large Top Service Panet
AN6323-01AC Hamess Assembly046284.01Small Top Service Panel
04632401Video Hamess Assembly046294-01Floor Frim
AD6325-01Motor interconnect Harness Assembly046296-01Front Canopy Support
A046326-01PCB Interconnect Hamess Assembly046297-01Center Canopy Retainer
4046335-01Ribbon Cable Assembly to the Shifter046299-01Display Shick) Retainer
A040336-01Ribbon Cable Assembly to the Motor046313-01Monitor Shield
AOA7752-01Ribbon Cale Assembly to the PCBs046316-01Under-Dash Cover
AO6340-01Component Bracket Assembly:046372-01Seat Shield
A039234-01Component Bracke Harness Assy.046390-02Bumper Pad
A046341-01Coin Counter Assembly046401-01Top Left Decal
11506-410310K Q Porentiometer Audio Taper046401-02Top Right Decal
160034-24]Slide Switch46402-01Video Pisplay Bezel
160049001Push-Button Switch046404-01Low Back Seat

046415-01 Hole Cover Plate

iA046345.01Power Supply Assembly (See Figure 4-10)046498-01Foot Pedals Cover
AN46355-XXSeat Asseaibly? (See Figure 4-2)04704908Front Floor Pane!’ (for Seat Assembly
ANS6380401Chutch And Brake Pedal Assembly (See4046355-03)
Figuee 4-7)04777201Right Canopy

047773401 Left Canopy

8046403-01Gas Pedal Assembly (See Figure 4-8)04777401Top Canopy
5A046491-02Sound PCB Assembly047783-01Pedal Mounting.
A047046-03ADSP II PCB Assembly047788-01Upper Rear Panels Decal
AQA7724-01DSK PCB AssemblyOATTBB-OZRear Door Panels Decal
ACAI 74G-01Main Harness AssemblyO47788-03,Lower Rear Panels Decal
ADITISODLLink AssemblyO477B9-O1Number Plate Decal
AQAT?49-.01Link Harness Assembly097790-01Left Inner Decal
O47779-01Link PlateO4779-02,Right (nner Decat
178303-001Jackscrew Kit047791-01Bottom Left Decal

047791-02 Bottom Right Decal

AQS7757-04Control Panel Assembly (See Figure 4-3)047792-03Left Canopy Decal
ADN7798-01Attraction Assembly, Replaceable Parts;047794-04Right Canopy Decat
A047761-0Auraction Sign Sub-Assently04787301Shift Mounting Plate
A}46338-01Attraction Harness Assembly139019-00)25-Inch Framed Color Raster, Medium Res-
47793-02Attraction Decalolution Video Display
O47 780-01Attraction Shield148007-1044 1/2-Inch Diameter, 6Q, 10W Shielded
M6WS-01Attuactlon CoverSpeaker
(4777801Attraction Frame.171002-001Exhaust Fan
O77E1-OLAtwaction Retainer171027-001Coin Door (See Figure 4-9}
170003-0011&4nch, 15 Watt Fluorescent Light175004-706,.154 LD., 375 O.D. Fiber Washer
T?HI86-001,18-Inch Fluorescent Lamp Fixture173004-708-190 LD., 640 O.D, Fiber Washer
178032002#10 Screw Tie175014-1040.218 x .500 x .050 Flat Zine Washer
¥78232-001Fluorescent Lamp Retaining Clip175014-1050.218 x 625 x 065 Flat Zinc Washer

Nole: For the details of all the paris of the Race Drivin’ Board Set Assembly (part no. \047877-OD, see Figure 3-18.

Page 80

Alustracest Parts Lists Race Drivin’

Cabinet-Mounted Assemblies Parts List

Part No.DescriptionPart No.Description
175014-10561344 x 688 x .065 Flat Zinc Washer72-1630F6-32 x 3.125 X-Rec Pan-Hel, Screw
173014-3040~218 x .500 x .050 Flat Black WasherP2516#10-24 x LO Hex Head Screw
175014-3050-228 x 625 x .065 Flat Black Washer72-33201/4-20 x 1 1/4 Hex Head Screw
176013-110710 x 3/8-inch Pan Head Tapping Screw72-352814-20 x 1,75" Inch Hex Head Screw
176019-22828 x 1 3/4-Inch Black LPW Screw1780230011/4-20 x 2.0 Hex Screw
176020-208#8 x 1/2-Inch Black Phillips-LPW Serew72-59125/16-18 x 3/4 inch Hex Head Screw
176020-212#8 x 3/4-Inch Black Phillips-LPW Screw:7246168#6 x i-Inch Pan-Head X-Rec Screw
176020-220#8 x1 V/4-Inch lack Philtips-LPW Screw73-0408#10 Stee] Split-Lock Washer
176025-44201/4-20 x 1.25 Black Tamperproof Screw73-04355/16 Steet Split-Lock Washer
176025-4108#10-32 x 1/2-Inch Black Tamperproof75-04581/4 Steet Spllt-Lock Washer
Screw73-05581/4 Steel Black Oxide lock Washer
176025-44201/4-20 x 1,23 Button Cap Tamperproof75-5520B2/4-20 x 1 1/44nch Round Head, Square

Screw Neck Black Carriage Bolt

176033-1610#6 x 5/8-Inch Phillips-Pan-Head Screw75-5524B1/4-20 x 1 1/2-Inch Round Head, Square
1770001441/4-20 Hex NutNeck Biack Camiage Bolt
277030-2441/4-20 Polymer Lockout75-5528B1/4-20 x 1 3/4-Inch Round Head, Square
177010-44010-24 Polymer LocknutNeck Black Carriage Bolt
177012-111Ptish On Spring Nut75-3540B1/4-20 x 2 1/24Inch Black Carriage Bolt
177023-0011/4-20 Togglewing Spring73-070021/4 Pender Washer
177024-01441/4-20 Low Crown Nut75-995696-32 Nut/Washer Assembly
178018-00112 x 5/8 Staple75-99518#8-32 Nut/Washer Assembly
178032-002=10 Screw Hole Tie, Wire & Cable7813011Bonding Agent

178041-007 3 x 3-Inch Press-seal Bag

178056-002V2ineh Wide Foam ‘ape82-81128#10-24 x 5/8-Inch Black Hex Socket
178093-001Fan Biade GuardBution-Head Screw
178120-606PCB Standoff82-8116B#10-24 x I-lnch Black Hex Socket Button-
378326-002Tamperproof Hex Key DriverHead Screw
178254016,Double-Coated Acrylic Foam Tape82-85241/4-20 x 1 1/2-Inch Black Button-Head
178257-004Black Square Finish Plig,Screw
178263-04021/4-Inch Wide Foum Tape82-$532B44-20 x 2-Inch Black Button-Head Screw

178274-001 Black Adhesive Back Foam 178292-032 2nch Safety-Hazarct Reflective Tape

1 A045988-01 is the US, version. AOS 988-02 is the German version. AGI5988-03 Is the right-band-drive British version, Documentation for the Race Drivin’ simulator: SP-351 Race Drivin’ Schematic Package ST-351 Race Drivin’ SelfFest Label TM-295 Welts-Gardner 25-Inch, Medium-Resolution Color Display Service Manual (for Modet 23K5515) ‘TM-331 Race Drivin’ Operator's Manual

2 AG46355-01 is the seat assembly with @ 1/4-inch metal. plate that ts bolted to the left side of the cabinet (as shown in Figure 4-2), 4046355-03 is the seat assembly without a 1/4-inch metal ‘late that ts bohted to the left side of the cabinet . A04G6353-03 replaces AOIG355-01,

3 Front floor panel 046278-01 gous with the sea that i bolied to the left side of the cabinet. Front floor partel 047049-02 goes with the front floor panel 046278-01 if it is ready installed, f assembly AOLOZIS-O1. It has the cutout for the metal, ‘plate on the seat assembly

Seat assembly AO4G353-03, However, the sont assembly AO46335-03 can use the

Page 81

Ruce Drivin’ Mlustrared Parts Lists.

Page 82

MWustrated Pasts Lists

ltems Not Shown:

ADARIAOT Sout Fen Hamess Aacy. 178100-06 17D 4.28" 1.0, Bepeing }—§wrr ef £O.0, Waster Pptces) Os6571-01 ‘ube ibatwsen pivel block & unger s7abab Rss bedeing Ir rad maunting box) 1.95" Spring Pin AOSEIII-OT ‘Seal Hamess 105007-401 Tanase Lack Aghasive

72aB12 SHIS-1B x75 Hex-Hd, Scien TS-OAIS, ‘SpE Lock Washar 75018-1058 Flot Washer

Wren T2320 448" Toggle Nut WA20 «8.25 73-0702 Hex-Ha Serow | ssa” Fender Washor i] TSOASS 725528 ‘Splh Washor M420 x 1,75 — 1?8e-1050 Har-Hd Screw | » Fag Masher |

s77a10-2601 2 f 518" Locknat 7 7 V72017-4616 i Snouktar Sera f i

7555203 Carlage Bot TNO Wa* Lockrat 750158 Figt Washer

O96356-XX Stat Assy. Frame Race Drivin’

‘Seat In rotated Aituatration purpopes.

05650001 Beat

0464800 ‘Seen Maung Pasar penter-99 Seat Mouring 178100-007 Box 15" 1,0, Bearing (2 pleas) aseses-o1 Py: Mounting Bow waz Algh Thread Eng Prate

Rod Ent TTA aS 172021-008 ‘ 3B" Hx Nul | Right RodEnd ee 17700-4143 panseg.on | 5024 Hex Nut Saat Pivot Arm + a7iabi1-006 38 cd Ene cc W72021-106 77000-1485 % 5 Lent Thread 318-26 Hox Nut lod fred

ome Bottom Cavar 49008-1001 ‘SK Poleniieenster ireseeter Potemceat 24-Toath Gear

72-2008 10:32 x 172" Hex Soe-Hd Cap Sera ‘76.0403 70026-8108 310 Lock Washer 10-92 2 0.375

s7aNaH.2698 2.25" Spring Pin

72-8008 10-32 * 1/2" Mox Soo: Hd Gap Scraw T5080S FID Spl Lech Washor 1750161040 #10 Washes

Figure 4-2 Seat Assembly A046355-Xx!

Page 83

Race Drivin’ Mlustrated Parts igs

Seat Assembly Parts List

PartNo.DescriptionPart No.Description
8046333-01Seat Harness Assembly172017-46285/16-19 x 1.75-Inch Long Socket-Head
AOHG334-01Seat Flex Hamess AssemblyShoulder Screw
046350-02Metal Seat Frame172020-24285/16-18 x 1.73-Inch Slotted Spring Pin

046357-01 Seat Mounting Box 172020-2436 .375-Inch Diameter x 2.25-Inch Slotted

046358-01Magnet AemSpring Pin
046359-XxSeat Mounting Piutform?172021-0063/8-24 Rot End—Right Hand ‘Thread
046360-01Seat Pivot172021-1063/8-24 Rod End—-Lelt Hand Thread
046361-01Magnet Pivot Bracket17501201351.25-Inch L.D. Washer
046%62-01Magnet Bracket175014-1032#8 Flat Washerr
O46363-01Mounting Box End Plate17514-1040#10 Flat Washer
6364-01Bottom Caver for Mounting Box176023-4106#10-32 x 3/84nch Tamperproof Screw
046365-01Potentiometer Bracket177000-1493/8-24 Hex Not
146366-01Seat Pivot Aen177010-238#8-32 Polymer Locknut
046367-01Modified Gear177010-2465716-18 Polymer Lock Nut
046370-01Seat Support178032-002#10 Tie, Wire & Cable Screw Hole
046371-01Tuhe178065-100Adinch Tie, Wire & Cable
046373-01Magnet178068002Inch Cable Tie Mount
046404-01Seat178101-00724-Tooth Spur Gear
G47795-0FHose Clamp.72-1828F*8-32 x 1 3/Linch Pan-Head Screw
O71Adhesive, Threadlock72-8008#10-32 x 1/2-Inch Socket-Head Cap Screw

75-0408 #10 Split Lock Washer 119008-100) 3 KQ Potentiometer 172017-4616 5/16-18 x IeInch Long Socket-Head Shoulder Screw

1 4046355-01 is the seat assembly with 046359-01, the seat mounting platform, which has a 1/4-inch vertical metal plate that is bolted to the left side of the cabinet (as shown in Figure 4-2). A046355-03 is the seat assembly with 046359-03, the seac mounting platform, without the vertical metal plate on the left side, A046355-03 replaces A046355-01,

2 046359-01 is the seat mounting platform with the 1/4-inch vertical metal plate that is bolted the the left side of the cabinet. 046359-03 is the seat mounting platform without the 1/4-inch vertical metal plate. 046359-03 replaces 046359-01,

Page 84

Mkisiaed Pusts List Race Drivin’

| 75-8326B2S9t6B1760234520
Wh20x 1,75W818 x 1.0 But-WA-20 «1.25item Not Shown:
Carriage BattHo. Cap Serabien aadADATIAT-OT
12000144f¢ places)(+3050‘Switch Mamatahb
1420 Bax Nu}a" Fs WasherLaAer

ea7m02 t AgS7DOGO1

ae Fe‘Wet
jooAndsa60-01' ~May Ste Ay.
Push-On Spring NixPint Atay.H[See Figuraown

Figure 5S} 1

28a}ay Soh Pate

SIG 1.0 Butelie, Sorwe Fa

£4 pices)iFaei Key Switch een!
108007-004H| Basi
Thm lock Acnestve|iP7551088
tiPERMO2a x te

if Camoga Baht rN fz pieces) |

$4,3=i
|gianyygsteozs4108
-a| | tosex tee
a7m2s9188Iay,{11Yamperproot Sorew
SSOSA pteces)
144-20 Nut |oy{750143000
175014-2050,431D Fiat Washar
Flas Washerde| t4placesy
7$0558|idI7ro1.280
Lock Washer%S16 Nt

7555208} : 620 1.28} — O4SS

Gamage Bat!Le|suse PatteeTE Lock Washer

af J 038895-01 = i ? Satich Bezel 05845801

160052-007Treas +108opsc
Rod Pushbusion Switch?7889518OR x UEee4605001
/Mbaaaoe acidSxavting Whos!
OsrT7e-Ot‘WosharaCarrer Docat
Seavanort ParoNadFPS01440-04685744
04772269;‘F7aRASO2310 Flat WaharSteering Whoa] Hud
‘Seal Abort DocallGroon “Seat Adiust*M4 paces)
178028.4708Buran weapDa7778.0417e098-005
10-32 «0.80160045-003Central PanelStoating WasaPassa
‘Tamparpreat Screw;Snop-Action Switch987792.01175002000186-20x 21g"
th piseas)ContolPanet Decal — yyaanorSoot. Cap Screw
47014-3040 |ADITTAAOHTI7HO280
#10 Fist Washer,‘Seat Adjust Hamas Ass.e-bocknut

{4 pisces}

4-10 Figure 4-3 Dashboard Assembly A047757-01 A

Page 85

Race Drivin’ Hlustrated Pars List

Dashboard Assembly Parts List

Part No.DescriptionPart No.Description
A04G6460-01Steering Assembly160044001SPDT Snap-Action Switch
A0S7000-01Key Switch Assembly160052-001Red, Lighted, SPDT Pushbutton Switch
A067747-01Key Switch Harness Assembly175002001.750 Shaft Washer
ADI7748-01Seat Adjust Harness Assembly175014-3040#10 218 x 500 x 050 Fiat Black Washer
036995-01Push Button Switch Bezel176023-4108#10-32 x 1/2-Inch Button-Head Tamper-
46437-01FFB HubProof Serew
6458-01Cover177010-240#10-24 Polymer Locknut
46459-01Decal Cover177010-24010-24 Polymer Locknut

177010-260 3/4-16 Nyloc Hex Nut 046654-01 Mator Stipport Plate

O47775-03Conirot Panel178099-00512-inch Deep Dip Steering Wheet
7776-01Seut/Abon Plate178233-0026.3 V “Seat Adjust” Button With tamp

ATI77-OF Key Switch Plate 72-8512 V4-20 x 3/4-Inch Socket-Head Cap Screw

04779201Controi Pane] Decal75-04384 Spiit-Lock Washer

047792-02 Control Panel Key Switch Decal

647793-03Control Panel Seat/Abort Decal73-$108B¥10-24 x 1/2-Inch Black Carriage Bolt
106007-001Adhesive, Thread Lock7399518#8-32 NuVWasher Assembly

82-8916B 3/816 x 1Hinch Black Button-Head Cap Ser

4-11

Page 86

EMtusteted Pusts List

70003 | #10 Leek Washer

UE Nylon Waahar

048450-01 Actualor:

178001-004 Rtalning Ailng|

‘6004-003;

AOATTAT Kay Swich Hames Asay. Tee #10-32 See-Ha, Cap Screw tame Not Shown: Tepa0a14 osasapoF Spring Pin lel 728008 #1088 Soe-tid, Cun Seraw areae oot 75.0008 Foren Speing #10 Spit-Lack Washar

1 178001-004 ! astalning Rng i, li rs a wal i

i ® iH i 0aE4seo1 Housing

oneaeent Key

PIS 34-40 Pana Serow 178014-9018 #4 Flat Washer 77010202 44-49 Locknut

Figure 4-4 Key Switch Assembly

4-12 A046445-01 C Race Drivin’

Page 87

Race Drivin’ IWusteaed Parts List

Key Switch Assembly Parts List

Part No.DescriptionPart No.Description
A087747-01Key Switch Hamess Assembly175009-364Nylon Washer
4644801Key176008-110"10-32 x 5/B-Inch Nyloc Socket-Head Cap
046-449-018ShaftScrew
646450.0)Actuator177010-232#440 Locknut

178001-004 1/2-Inch Retaining Ring 146990-01 Housing

107029-001Lithium Grease178256-001Torsion Spring,
160045-003SPDT Switch72-14128"4-40 x 3/4-Hich Pan-Head Screw
¥72020-08146,125-Ineh x 0.875-Inch Slotted Spring Pin173014-2018#4 Flat Washer

‘75-0408 #10 Split-Lock Washer

4-13

Page 88

Illustracecd Parts List Race Drivin’

DABTEOY a" Spacer

Teasiz Wee20 Sertve 760483 H4 Lack Washer 046862-01 175061050 Fusbbar Stop 112? Flog Wiathor 175028015 | ni 948063-01 Ertonslon Sprig q Rubbor Stop Bracken paint if 178181-7808 ‘ ‘Sueol Spacer TRO ‘Shearing Wheat AQABTRDS OAGASTOY = 175002001 Motor Assy. Hub Flat Washer

ouease.ct OAGAS8-01 Hus Cover | Hub Decal

Lecerut su

‘Washor Soe-Ho. Seraw

Figure 45 Steering Assembly A046460-01 C

Page 89

Race Drivin” lustrated Parts List

Steering Assembly Parts List

Part Ne.PescriptionPart No.Description
A04G6331-01Stecring Assembly Harness177010-2388-32 Locknut
08633201Motor Assembly177010-2603/4-16 Lockaut
086378-013/4-Inch Spacer177011-2663/4-16 Thin Lockaut
046454-013-Rotation Stop178026-0153/l€-Inch O.D. x 1 4/8Inch Extension

Spring 046455-01 Stop Bracket

046456-01Potentioneter Bracket178065-1004-inch Wire and Cable Tie
046457-01Steering Wheel Hub178099-00512-Inch Steering Wheet
046458.01Hub CoverT78181-78063/8-Inch Long Stee! Spacer

72-8512 V4-20 x 3/4-Inch Hex-Head Cap Screw 046459-04 Steering Wheel Hub Decal

016462-01Rubber Stop176022-3806#8-32 x 3/8-Inch Hex-Head Cap Screws
046463-01Rubber Stop Bracket72-8810#8-32 x 5/8-Inch Hex-Head Cap Screw
AS64901Gull Wing Support72-BB1G#8-32 x 1-Inch Hex-Head Cap Screw

175014-1050 1/4 Flay Washer (for ground wire} 106007-001 Adhesive Thread Lock

119038-00110-Tum Potentiometer175014-1032#8 Flat Washer
17500240010.7304ach Flat Shaft Washer75-04581/4 Split-Lock Washer
17622-38068-32 x 3/8-Inch Thread Lock Hex-Head78-1709Lubricant

Cap Screw

4oiS

Page 90

Mustrated Parts List

ftems Nat Shown: ADATTSS-OF ‘Shitor Jumper Assy ised a2 x 2 Soe-HE Cop Som

soe xa SogHe, Cap Sxew TBatd 081 60 Fla Washoe eBAzeo1 ‘Gate Larch 177000-132 $440 Hox Nut (2 pisces) FR Acar 440 x 12 Panic. Sere 12 ehicosp Detail of shifter gate

¥72020-0814) 16" Oi, x 71 Sing Pre

AEST? 11800-1901 Pitch Bar|

72.8908) N82 x 12" Sood Cap Seren] 17 7000-138) 28-32 Han Nut!

7ata0F carresn: R 20-22 x i Ponstig, Serene 1S. Scere| ninge Walamen 177010281 82 % oaresz.o1 1 Roma He ae ean te Race Devin’

onrTa-o1 Face srenas-4455 ‘wnox 1 Salleang BLE HE Cap Sexo ol sms 47TH OO ‘7a-tB10F|

Bextr Paes SarSila Boa
Pintraster4° Win & Cabo Te

a aeen sramnsare fants ait Wie, 2° 4, 32 Potymer Hax Loch race

wend2TRADI
Latch Bearing!2emg

DoS g Soubiasiiad Fearn

=GetTope inside

ae seeTo-08 Sutter Hearing Bs ervey AOSTA ‘We-20 Palsr Hax Loco fons Nebr {2 elect} 75-5528) 116-20. a" Curiage Sal q : H fe fate EE Fett Link i 72-100F 652 x 112 Pane, Screw THTVOH38 ea Hexcblut anasto eeramat

fob BarDectLaver

Decent Roller Herre od7e6-05 Ble Hor Sects, tovor Spacat Sheulder Serow ene £2 places) Sox t 1a" Lerten Setd, Cap Seren Towed 75016-1085

AthesivaCrocsgu

vere 7TH 244 Hs 11-20 Pobyenar Hox Locket 14-20 4.87. sy Soolid. Cap Screw recs 75-045 Excenshan Spring % 4116" Lock Washer pm

S,SB.I7SOTH TOOPVE Tubing
~Rat Washerraeoro

BR XS" Sota. Cap Seren TrrCO4s pez e500 bert AO #1 Butt He, Cap Jacenting Pisa 108007-004 443008001

>12V 96 Salencid|Than tock
385-1806Achesiva

hada 787-01 Flat Couriers ee spony Tab ber T7ap1eA0H 1198007-001 ae Threat Lock aches oa ea Hieoner yeas0a| aaa I5 Bx 1° Sota | Soon. Cap Serow Gap Screw @ Pisoes) 7080904 3780161031 Bearing HER vies

2Pom)158 Dit x Fg?Pa
75-0485;78!Spring

“iste! Detail of Solenoid Mounting Plate Figure 4-6 Shifter Assembly A047796-01 A

4-16

Page 91

Race Drivine Miustented Parts List

Shifter Assembly Parts List

Part No,DescriptionPart No.Description
AQST751-01Hamess Assembly177000-1388-32 Hex Nut
A047753-05Shifter Jumper Assembly177000- 54}#1032 Hex Nut
H46424)]Reverse Position Latch177020-238*8-32 Polymer Locknut
04644001Reverse Position Luch BearingL77010-241#10-32 Polymer Locknut
46476-01Shifter Gaie177010-2441/4-20 Polymer Locknut
O46177-01Pitch Bar178026-017Reverse Position Latch Spring
04647807Pitch Link178026-023Extension Spring
046479-01Shifter Housing17806$-400‘4-Inch Black Tie, Wire & Cable
046481-01Roll Bar178066-934375 x 1.75 PVC Tubing
046482-01Roll Link178254-016i-Inch Double-sided Tape
75HBoot Cover Plate178293-0123/4-Inch Doubte-Sided Tape
04753101Solenoid Pinte72-t010F#10-32 x 5/8-Inch Pan-Head Screw
04786101Pivot Shaft72-1408"#440 x 1/2-Inch Pan-Head Screw
047862-01Detent Place72-1008F#6-32 x 1/2-Inch Pan-Head Screw
047863-01Detent Lever72-1818F*8-32 x 1 1/8-Inch Pan-Head Screw
4786401Detent Roller72-801098-32 x 3/8-Inch Socket-Head Cap Screw
047865-01Spacer Lever72852034/4-20 x 1 1/4-Inch Socket-Head Cap
047866-01Spacer RotterScrew
047867-01Extension Spring Tab72-88058-32 x 3/8-Inch Socket-Head Cap Screw
4786-01Solenoid Link72-8807*8-32 x 7/16-Inch Socket-Head Cap Screw

72-8808 #8-32 x L/2-Inch Socket-Head Cap Screw 04779741 Knob

O47798-01Boot72-8020.187 x .123-Inch O.D. Shoulder Screw
106007-001Adivsive Thread Lock72-85141/4-20 x 7/8-Inch Socket-Head Cap Screw
11908-10013 KQ Potertiometer73008241/8-Fnch Diameter x I 1/24nch Cower Pin

75-0458 i/4-Inch Lock Washer 143004-001 Solenoid

7720200814V8 x 7/S-Inch Spring Pin73-048s#8 Lock Washer
72020-1014-196 x 7/8-Inch Spring Pin755528314-20 x 1 3/4Inch Carriage Bolt
175014-1034#8 Fiat Washer76-080301-187 Nyliner Bearing

82-8508 14-20 « 1/2-Inch Button-Head Cap Screw

173014-1050-623 x .27-fach Flat Washer85-19068-32 x 3/8-Inch Flat-Head Countersunk
76025-44161/4-20 x t-Inch Self-Locking Butt-Hd, CapScrew

Screw ¥77000-132 #4410 Hex Nut 37000-1346 #632 Hex Nut

4.17

Page 92

WMustrates! Parts List Ruce Drivia'

74 407013-001 Light Olt

NOTE: Lubricate on both ends of shafts.

Ospaet.o1 Lothing Tab | 176022-3604 ‘OaseD tor G1 Hex Soe-Ht Cap Sexww ‘Spring Hovslng Spacer & Splces)| Te6812 fet Se-H, Sore Chater Link: 177010-236

72-0812 96-32 Hax Soo-Hs Cap Sov TTF 6-32 Lochrest ‘175014-1028 (8 Fist Washer 178191-d604 ie" Space

728808 #822 Sera

ent ‘Spring Front Shan Cover] 04698795 4° Clutch Spring Shah

osnaago1 14-Teaih Spur Gegr|

Ganzsa0H €0-Tootn Spur Gaas| 4760229604 ‘Sat Scrow on €0-Tosth Gass

ADase08-01 ‘raha Pedal Assy, Ginoudes aren gaumge & surdin gaupa hamesa}|

Figure 4-7 Ciutch And Brake Pedal Ass:

4.18 SK Potentiometers aN 439008-1001 Locsenun

oxesaB-01 F Cac Shar

osesreot asich Besring Tab

A046380-01 E | re Assembled Clutch & Brake

tr6398-9) Srako Eng,

F7AI8Y-3608 v4" Spacer 478120-608 PCB Stancott s77010-298 Locknut

i 7588408 SS ‘Wa20 Canioge Bort ‘ wraieant Push-On Spriag Mus 75-0700 Fandor Washer osexeg-ct Podal Frvat TIONS f Pr ise Locke

embiy

Page 93

rs

Race Drivin’ Wlustratect Parts List

Clutch and Brake Pedal Assembly Parts List

Fart No.DescriptionPast No.Description
A044827-01Brake PCB Assembiy160044-001Snap-Action Brake Switch
A04633001Brake/Chiteh Harness Assemhly17514-1026#6 Flat Steel Zinc Washer
0235-0160-Toath Spur Gear with Hub76022-3604#6-32 x 1/4-Inch Socket-Head Cap Screw
040249.071M-Tooth Spur Gear with Hub (Acceptable177000-147*5/16-24 Hex Nur

Substitute is part no, 046050-02 when used

with part no, 72-8404, screw cap, and par177010-232#440 Locknut
no. 106007-001, adhesive.)177010-2366-32 Locknut

177010-238 ¥8-32 Lockout

0§3401-01Spring Housing Spacer (Acceptable substi-178012-0043/8-Inch Diameter Retaining Ring

tutes are part aumbers 178266-6620,

178266-3620, 17826-7620, 17826-0620,178026-020Clutch Extension Spring
178266-2620,)178120-606PCB Standoff
046379-01Clutch Bearing Tab179181-36041/4-Inch Spacer
i6361-01Frame178244-220Actuator Clarop

046383-01 Chteh Pedat 7216325 *6-32 x 2-Inch X-Rec Pan-Head Screw

04633401Cover over Rear Spring Shaft72-8412#4-40 x 3/4-Inch Socket-Head Cap Screw
046385-0)Clutch Spring Housing72-8612#632 x 3/4-Inch Socker-Head Cap Screw
046396.073-Inch Clutch Shaft72-8808#8-32 x V/2dinch Socket-Head Cap Screw
046387-014-Inch Clutch Shaft75-990006026-32 x 1/2 x 312 Neoprene Blind Nur

056588-04 Pedal Pivot Shaft 046389-01 Stop Bracket CAUTION:

4639001Bumper PadThe following eight Parts (grouped as the Brake
046391-01Citch LinkPedal Kit Assembly) tequire critical sub-assembly

procedures before being installed in the Clutch and

46392-01Brake Switch ActuatorBrake Pedal Assembly. we highly recommend you
046303.01Locking ‘Taborder this group of Parts as part ne, AO46499-01, in
046394-07Cover aver the Front Spring Shaftwhich case Atari Games will assemble them:
6995-02Brake Compression SpringA046342.01_Brake/Strain-Gauge Hames Assembly

046382-04 Brake Pedal

berseityee046495.01Bondable Terminat
397-01Brake Guide Cap106012-001Rapid Cold-Curing Adhesive (thin Teflon
046398-01Urethane Brike Springtape)
46399-01Brake Rad106002.003Adhesive
peice34-loch Rubber SpaceritpaPeck and Cable Tie
106007-001Adhesive Thread Lockkejs
107013-001Light78-13003-Silicone Adhesive

41908-1001 3 KQ Clutch Potentioneter

Page 94

Iluseraied Parts Lists Race Drivin’

e9nes6-01 Pivot Pin

sanadoot Foot Pedal Accolerstor oS / raaveens i \ Retelaiog ov0oze-o1 \ Pedal Compression Spring

“ o39703-04 | “— ‘Catia Extension Spring | F -

ose738-0t cata

Pulley Bs < Fe - t

Semen _———, TROD Pedal Extonsion Spring ween xs Ad | Soraw on829-01 Foc Pada Control 149008-1007 Base Pista ‘SK Potemiamater ih

Fo Bipok

White DAE298-01 a Heme Not Shown; Foot Padat @racket ADASTO Gas Pedal Harness Assy. S77DTD2AD #1024 Lochnut 1760141040 #40 Washer i y07012.001 Dry Tollon Spray Lubstoant

8 parts shown sbove make up the Foot Conlrat Assembly, part No, A08235-03 The Foal Conte Assembly 6.4 large eubsseornbty ot the Gas Peal

Figure 48 Gas Pedal Assembly A046403-01 A

4-20

Page 95

Bace Deivin’ Mitstrated Parts Lists

Gas Pedal Assembly Parts List

Part No,DescriptionPart No.Description
A039235-03,Foot Control Assembly, Replaceable Pars:107012-001Dry Teflon Spray Lubricant
039236-01Pivot Pin478012004Retaining Ring for 3/8-Inch-Diameter
939238-08PulteyShaft
035230-01Foot Ped: Conrol Base Plate119008-10015 KQ Potentiometer
939240-01Foot Pedal Accelerator72-8606#632 x 38 Inch Socket-Head Cap

Screw 03924201 Cable

639703-01Cable Extension SpringA043947-01Gas Pedal Harness Assembly
03970401Pedal Extension Spring046298-01Foot Pedal Bracket
040028-01Pedal Compression Spring177010-240710-24 Polymer Lockout

175014-1040 #10 Flat Washer

Page 96

Mlusteaued Pans Liss Race Drivin’

8-10870 (Coin alien Lever & Sud 20-108 alt Coin iniot

eo. to1aT Haeness Asty.

setar13 1 Key Hook q “— 4 Locked rei HITISS r ight Con intot i 3 Z [ H Y I AT1005-035 t Bs 25 Cord NOFTYL Accapeer BS10140 | ™~ ™, ‘Coin Door iangr Paral a TE SMBS | > ~~, Leck

FR 10704| APE, Bar Kaaper |

3a-10154| SMsich & CAEN. Bracket

§ 2O-1DOTS thew 83-1078 T Getch Wires 99-10068 Coin Crige seagisa . Switch Cova ~,

‘PR TO082 than 9-100 Coin Switch Assy.

Figure 4-9 Coin Acceptors, Inc. Coin Door Assembly 171027-001

Page 97

Race Drivin* IWustrated Pans Lists

bS-10161 eo10160 9010117 Side Entry Button Assy, — Coin invot [Coln elu Door 99-10158 Bezel Bution Cover 98-7059 futen Only eo-10144 99-19070 72.Matg04C 25 Cont Donal [Coin Rotem Bazat ‘90-1014 Token Decal! gS

Q9-40115 Spring tor Button

” a 9210185 86-15110 “ Coin Box & Enclosure Enclosure Agsy. 99-10145 ‘Sido Mounting Cop.

910170 Frame Clamp Screw 2

Caln Daor|

99-10139. Sorviee Door| 99-1069) LD, Laball

910149 Ola Cast Frama

P< 2 alll 39-70760

“>HiCain Counter
aaeeMounling Screw
gosorez,i}iii°

Coin Box tte j_ seins Ld 7/8 Flat Kay Lock oo 39-10168 “s Colne: Countor

99-10167 | pt Can’ Lock

Figure 4-9 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001

Page 98

iflustrated Parts Lists Race Drivin’

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part No.DeseriptonPart No,Description
160057-601Colp Switch99-20081Key Holder
70-11-47Mininure Bayonet Lamp99-10096Fastener
72-9406S#440 x 3/€-Inch Truss-Head Screw:99-10204Bar Retainer
72-HA1404C#440 x 1/4-Inch Pan-Head Screw910103Bar
T2JA1{05B#440 x .31-Inch Pan-Head Screw99-10115Spring
‘7514125#440 x 3/4inch Pan-Head Screw99-10116Plastic Coin Return Lever
177010-232#440 LocknutSD-10317Steel Coin Retum Door
9910008Retainer99-10139Coin Door
99-10042Coin Switch Assembly for Belgian $ Fr and99-10140Coin Door inner-Panel Assembly
US, 25¢99-10141Die-Cast Coin Return Cover
99-20043Coin Switch Assembly for German 1 DM,99-20143Coin Door Frame
Japanese 100 Yen, Swiss 1 Fr99-10144Channel Clip

99-10044 Coin Switch Assenibly for German Z DM,

tullian 100 1, U.S. $1.009910147Hamess
99-100435,Coin Switch Assembly for Australian $.20,SHOLock Assembly
German 3 DM, British 10 P99-10149Service Door

99-10150 Switch Cover 9910068 Coin Reiurn Chute

99-10073Switch Wire (included in coin switch99-10151Left Coin Inlet
assembly 99-10043)99-10152Right Coin Inlet
9910076Switch Wire Cincluded in coin switch99-10153Coin Retum Box
assembly 99-10042)910154Bracket Assembly

99-1007 Switch Wire Gneluded in coin switch

assembly 99-10044)99-10160Linch Wide Die-Cast Coin Inet Housing

99-10161 25¢ Amber Side-Entry Coin Button

99-10078Switch Wire Gnetuded in coinswitchAssembly
assembly 99-10045)99-30370Screw for Clamp
9-10080Lamp Socket171006-035Metal Coin Mechanism for U.S, 25¢

4-24

Page 99

Race Drivin" Itustratedt Purts Lists.

N O T E S

4-25

Page 100

Ilustrated Pags Lists Race Drivin’

rraza1-o92 - mpar Assy. atone

eatenoeertper Ay.ronan
rembaelel|Armper Asay,Power Supply
|woK

®

oSalle2©

®: Lin seaarheon bag °

Buwe@@

Bi 48008-7002 BK 7h, 250 Fung Rae

R 1TBMS-205 | bia

  • ® @] 3 Fs z ° af 3: {e) ab wa
aenne.40e2rae 08-20%z4142044001AD MADD
4A, 250¥ Fuse2A, 250¥ FursFransomerAPU PCR Assy.

Figure 4-10 Power Supply Assembly A046345-01 C

4-26

Page 101

Race Deivin® Mhusteated Parts Lists

Power Supply Assembly Parts List

Part No.DescriptionPart No.Description
AQ42384-03Line Filter Assembly146008-20222 Amp, 250V Slow-Blow Fuse
A043367-01fumper Assembly146008-40224 Amp, 250 V, Slow-Blow Fuse
A0SS4S1-ODRace Drivin’ Audio Power Unit (APU) PCB146008-70227 Amp, 250 V, Slow-Blow Fuse
Assembly (see Figure 4-12)149008-0025 V, 15 A Hitton Switching Power Supply
ANAGI601lS-Inch Black Jumper Assembly{seu details below)
aonRoe Sek Ger eyYroaas-2u05$osionRuse Bock
5‘useBlocveriPositionloc]
B70Power Supply Warning Label179231-0022-Position Terminal Block
044819-01Power Supply Chassis Base72-1604F#6-32 x 1/4-Inch X-Rec Machine Screw
046347-01Power Supply Fuse LabelT2-HASGO6S96-32 x 3/B-Inch X-Rec Screw
42044001Transformer72-HA48068#8-32 x 3/Sinch X-Rec Screw

Hitron 5V, 15 A Switching Power Supply Sub-Assembly Parts List

Part No.DescriptionPart No,Description
Transistors99-211026Resistor, Carbon Film, 330 Q, £556, L/4W
99-21 1002istor, NPN, 2SC1413A99-211027Resistor, Carbon Film, 5.6 Q, £5%, AW
99-211003‘or, NPN, PES050B99211028Resistor, Carbon Fila, 82 22, £590, 1/4
99.-211004or, PNP. PE8SSOB99-211029Resistor, Carbon Film, 10 2, 45%, 1/4W
99-211062Transistor, 2817252-.
99211063Transistor, PE8S50B99-211030Resistor, Carbon Film, 39 Q, £59, /4W

99-212031 Resistor, Carbon Film, 36 £2, £59, 1/40

Diodes99-214032Resistor, Carbon Film, 1K 2, £59, 1/4W
$9-211005Diode, Schottky, S10SC4M99-281033Resistor, Metal Film, 2K &2, 42%, 1/4W
aebeen99-211034Resistor, Carbon Film, 180K 2, +5%, 197
99.211008Diode:Rectines15400699-211035Resistor, Carbon File, 2K 2, +5%, 1/4W
pone, Recullies, 199-214003Resistor, Wire Wound, 27 0, 45%, 2W
spaviinDi ce, Pa Recovery, necro99-211066Resistor, Carbon Fitm, 6.8 2, 5%, 1/207
le, FastRecovery,.
9-211032Diode, Switching, 1N414899-211077Resistor, 470 9, 1/20, 45%
2A,
99-211064Diode, $15SC4MaxalioreReslttnr, 1208 ©, 1%, 5%

99-211076 Diode, 31DQ04

99-211013Rectifier, Silicon-Conwotled, $2800spectin

99-211036 Capacitor, Metal Film, 0.047 pF, 250V

Resistors99-211037Capacitor, Metal Film, 0.22 WF, 100V
.antsa99-211038Capacitor, Metat Film, 0.1 F, 400V
eteHorioada ow99-211039Capacitor, Metal Film, 0.022 jaf, 100V

3 : , 50 2, £5%,

99-211016Resistor, Wire Wound, 150 02, £5%, 2W>‘iyy
99.211017Resistor, Wire Wound, 33 Q, 45%, 2Wanonpaar Corsa, 1600 Be a2a
.99-211042,Capacitor, Ceramic, 0,001 2F, 2KV
99-211018Resistor, Wire Wound, 0.47 Q, +5%, 2ii
99211019Resistor, Wire Wound, 120 ©, 45%, 2oeauI0eSCapacitos, Ceramic, 470 pr, IKV, 258
99-211020Thermisior, 0.5 &, #59, SW99-211044Capaci;
a72pacitor, Electrolytic, 470 WE, 25V
99-211021Resistor, 2.2K 0, £296, 1/4.99-21 1045Capacitor, Electrolytic, 220 jtF, 25V
7<99-211046Capacitor, Electrolytic, 100 pF, 200v
99-211022Resistor, Carbon Film, 330 ©, +5%, 1/2W_7ape
ppasioesResistor, Carbon Film, 370 @ 5%, 1/299-211047Capacitor, Electrolytic, 1000 Fr, 25V
99-21202:Resistor, Carbon Film, 470 &, 45%, 1/4W>‘
99-211025Resistor, Carbon Filin, 47 9, £396, 1/407nineapeeins Blectrolytic poe HF 16V

4-27

Page 102

Mlustrated Parts Lists Rage Delvin’

Hitron Power Supply Sub-Assembly, Continued Parts List

Part No.DesexiptionPart No.Description
99-211069Capacitor, Hectrolytic, 2200 UF, i6V‘Transformers
99-211070Capacitor, Electrolytic, 220 UR, 2599.211075‘Transformer, Power
99-211079Capacitor, DE7100F22M9-241083Transformer, Power
99-211080Capacitor, 1000 HF, 35V99-211089Transformer, 4.75 MEH

99-211092 Transformer

99-23 3083Capacitor, 470 UF, 25V21105!Ty
99-21 L0B2Capacitor, 220 pF, 16Vsensianslecmer,
99-211090Capacitor, Ceramic, 1000 pF, 2KVMiscellaneous
99-211091Capacitor, Electrolytic, 2200 pF, 10V99-211001Regulator,UA4SIAWC

tors 99-211056 Fuse, 2A, 250V

oo-211050teda99-211087Terminal Block, & Circuit

onsen 2110! Fuse, 2A, 250¥, Semko

99-211051Inductor, 7 WH, 35 MMmets*“™
99-211052Inductor, 15 Mit99-211059Hear Sink
99-211053Inductor, 1.5 MH99-211060Fuse Holder, 6.35 MM

99-241064 Heat Sink, 1.5 MM.

99-215034Inductor, 2.2 WH21FuseHolder, 5.2 x 20
99-2107Inductor, 9.8 1H99211072mews
99-21 1084Inductor, 8 JH99-211073Fuse, 2A, 125V
99-231085Inchactor, 9.8 WET99-211074Terminal Block, 9-Circuit

99-211086 Inductor, 0.75 MH 99-211087 Inductor, 2.2 0H 99-211088 Inductor, 66 MH

Page 103

eee Iusteated Parts Lists

N O T EB 5

Page 104

Mlusurated Parts Lists

Ele Ve aes RE CG CEE ay 2H H —— i Cat Gay Gad Ca Carieanmy “ga?

® tik CARE FE Cage CHEE. ath P= RU Ge oo ou peers Se as | Fei al 8 ae Se Cede] am a wl, Cane’ capt wl CaaS aaah = = le nae " nee came gcmne =e ==} CoE eae

leper EES occ)

  • Ballo "St ial:

A044425-01 G Figure 411 Race Drivin’ Main PCB Assembly

4-30

Page 105

Race Drivin" Mlustrated Parts Lists.

Race Drivin’ Main PCB Assembly Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.
Integrated Circuits80R 80SIntegrated Circuit, VRAM, G4Kx4, 150137553002
3KNOT LOADEDnsec (Acceptable substitute is pant no.
EYNOT LOADED137553-001, Integrated Circuit, 64x4,
138Integrated Cicuit, 74L8374137144-001VRAM, 120 nsec.)
aKUNOeLoapayii80U, BOW Integrated Circuit, VRAM, G4Kx4, 150137553002

nsec (Acceptable substitute is part no.

15MNOY LOADED137553-001, Integrated Circuit, 64x4,
20invegrated Circuit, 7443574137548-001NBAM, 120 esac)
20S, 20UIntegrated Circuit, 744SB23137513-001BOYIntegrated Circuit, 744808137484-001
2"Integrated Circuit, 74459823137523-00185CIntegrated Circuit, 741837413714001
25KNOT LOADEDDOP 908 — Integrated Circuit, VRAM, 64ix4, 150137553002
2MNOT LOAPEDnsec (Acceptable substiture is part no.
30BIntegrated Circuit, ADCO8OD137243-00%viper tneegeated Circuit, 64x4,
sDintegraCireuit,AD7SB2VRAM,nsec,,
ategricedCircuit, AD7S8BTHSOsu, gow integrived Circul, VRAM, 64K, 150137553-002
30PIntegsated Circuit, 7415245137134-001nsec CAcceptabte Substitute is Patt no.
505, 30)Integrated Circuit, 45 nsec337199-002137553-001, Integrated Circuit, 64x4,
30wintegenect Circuit, 45 nsec137199002VRAM, 120 nsec.)
30¥Integeatedl Circuit, 7415245137134-00195Integrated Circuit, 7418374137144-001
100K.integrated Circuit, 7418741370234001

35K NOT LOADED

33Mnoe LOADED200MIntegnited Circult, 7441808137460-001
40HIntegrated Circuit, 7418123137268-0011008 1008 ples Amery VEAM, 64Kx4, 250137553002
40S, 400)intit, 45ns002nsec (Acceptablesubstitute is part no.
EEiicgeated Cire,49 asec1571984137553-001, Integrated Circuit, 644,
SovIntegrated Circuit, 7415245137134-002VRAM, 120 nsec.):
508, 50Dimegrated Circ it TALS244ieee100U, 1OOW Integruted Circuit, VRAM, 64Kx4, 150137593-002
50MTmegrated Circuit, 7448123137268001Saes 00h begnndGece
50UIntex:mmrri-O01, Integratircuiti,
50S, 50UIntegrated Circuit, 74ALS574137548001VRAM, 120’ eaeehq
SOW—megnnted Clreuit, 74AL8574137548-0011OOYIntegrated Cireuit, 744508137484-003
5oYintegrated Circuit, 74A857:13 7547+
SiaseNorloabeoS770ageAntegrated Circuit, 7406137052-001
GOR 60SIntegrated Circuit, VRAM, 64Kx4, 150137553-002110KIntegruted Circuit, 74415138137517-001
nsec (Acceptable substitute is part no.110MIntegrated Circuit, 74415138137517401
137553-001, Integrated Circuit, 64x4TIOR, 2108 Integrated Circuit, VRAM, 64Kx4, 130137553402
VRAM, 120 nsec)—asec (Acceptable substitute is part no.

‘ 137553-001, Integrated Circuit, 64x4,

601, GOW Integetted Circuit, VRAM, G4Kx4, 130137553-002VRAM, 120 nsec.)
blesubstituteé.
raeca pate chee baHOU, 11OW integrated Circuit, VRAM, 64KX4, 150137553-002
VRAM, 120 nsec.)—nsec (Acceptable substitute is part no.
§5CIntegrated Circuit, 7418259137137001rarely integrated Circuit, 64x4,
70R 70SIntegrated Circuit, VRAM, 64Kx4, 150137553-002YRAM, 120 nsec.
‘ee ‘Acceptable substivte is part 0.37555-0ROHInsegrated Cicenit, 74774137436-001
137553-001, Integrated Circuit, 64x4,120KIntegrated Circuit, 7415393137146-001
VRAM, 120 nsec.)uo120MIntegrated Circuit, 7441508¥37460-002

70U, 70 integrated Circuit, VRAM, 64Kx4, 150 137553-002 — p

nsee (Acceptable substitute is part aoeiia1208, 1208 Integrated Circuit, VRAM, 64Kx4, 150137553-002

137553-001, Integrated Circuit, 64x4, nsec (Acceptable substinute is part no. WRAM, 120 nsec) 137553-01, Integrated Circuit, 64x4, VRAM, 120 nsec.)

BeIntegrated Circuit, 7418259137137-001120U, 120W Integrated Circuit, VRAM, 64Kx4, 150137553-002
BaIntegrated Circuit, 741514137056-001nsec (Acceptable substitute is pan no,

¥37553-001, Integrated Clreuit, 64x4, VRAM, 120 nsec.)

4-31

Page 106

illustrated Parts Lises Race Drivin’

Race Drivin’ Main PCB Assembly Parts List Designator Description Part No, Designator Description, Part No.

130MInfegrated Circuit, 74AL$161137470-001190Nintegrated Circuit, 74182451371344001
130P, 1305 integrated Circuit, VRAM, 64Kx4, 150137553-002190Integrated Circuit, 7445321374874001
nsec (Acceptable substitute is part no.190Wfntegrated Circuit, 74AL574.137136-001
137553-001, Integrated Circuit, 64x4,190YIntegrated Circuit, 7415259137137-00%

VRAM, 120 nsec.)

130U, 150W lategrated Circuit, VRAM, G4kx4, 150137553-0022004Integrated Circult, 696811375434001
nsec (Acceptable substitute is part no.200C, 200D Integrated Circult, RAM, SKx8,137535006,

137553-001, Integrated Circuit, 64x4, 150 nsec

VRAM, 120 nsec,)200EIntegrated Circuit, 4872-15, RAM137540-150
135¢Integrated Circuit, 74F74137436-001200FIntegrated Circuit, 7418245137134-001
1354Integrated Circuit, 74F74137436-001200H, 200) integrated Circuit, 7418244137038-001
135KIntegrated Clreuit, 744832137487-001200KIntegrated Circuit, SLAPSTIC 117137412-117
140Cintegeared Circuit, 74182441370384001200L.Integrated Circuit, 741832137464-001
140HIntegrated Circult, 7415393137146-001200MIntegrated Circuit, 74AL$138437517-001
140KIntegrated Circuit, 74Fi1137583-007200N, 200P Intepratedt Circuit, 741S24513713400)
140Mintegrated Circuit, 74ALS574157548-001
150CIntegrated Circuit, 7415245137134001
150EIntegrated Circult, 7418244137038-001The following 16 program chips arc for North American
iSOIntegrated Citewit, 741874¥37023-001Jeft-hand-drive simulators only:
200RIntegrated Circuit, PR EPROM13607-2002
150KIntegrated Circuit, 741820137060-0012005Integrated Circuit, PR EPROM36077-2004
150PIntegeated Circuit, 7448573137547-0012007Integrated Circuit, PR EPROM.136077-2006
1508-PSPIntegrated Circuit1375594NH200UIntegrated Circuit, PR EPROM36077-2008
1500Integrated Circuis, 74F2444375024001200¥Integrated Circuit, PR EPROM136077-2010
200"Integratex! Circuit, PR EPROM13607-1012
15907Integrated Circuit, 74A4$573.337547-001200%Integrated Cirenit, PR EPROM13607-1014
160CIntegrated Circuit, 7419244137038-001200YIategrated Circuit, PR EPROM13607-1016
160EIntegrated Circuit, 74ALS161137470-D02
260HIntegrated Cireutt, 74ALS32IS4OL001210RIntegrated Circuit, PR EPROM13607-2001
2105Integrated Circuit, PR EPROM136077-2003
160KIntegrated Circuit, 7415138137517-001210TIntegrated Circuit, PR EPROM136077-2005
160Mintegrated Circuit, 74FO4357437-001210UIntegrated Circuit, PR EPROM1077-2007
160PIntegrated Ciscuit, 7449373137547-00120vIntegrated Circuit, PR EPROM£36077-2009
160UIntegrated Circuit, 744500137480-001z10WIntegrated Ciscuit, PR EPROM13607-1011
210XIntegrated Circuit, PR EPROM196077-1013
HOWIntegrated Circuit, 7448973137547-0012N0Yintegrated Circuit, PR EPROM136077-1013
170¢Integrated Circuit, 7415245337134-001
TEIntegrated Circuit, 7415244137038-001The follawing 16 program chips are for German
170HIntegrated Circuit, 7415148137417-001ief-hand-drive simulators only:
200RIntegrated Circuit, PR EPROM136077-1202
270KIntegrated Circuk, 74ALS161137470-0012005Integrated Circuit, PR EPROM136077-1204
\70PIntegrated Circuit, 7415244137038-001200TIntegrated Circuit, PR EPROM136077-1206
1700integrated Cire4ASO8137484-0012000Integrated Circuit, PR EPROM130077-1208
180CIntegrated Circuit, 74ALS133137317-001200Vintegrated Circuit, PR EPROM16077-1210
200WIntegrated Circuit, PR EPROM136077-1012
380EIntegrated Cireun, 74AL5139137467-001,200Kintegrated Circuit, PR EPROM136077-1014
180S-GSP Integrated Circuit, 34010-50137538-002200¥Integrated Circuit, PR EPROM136077-1016
180Uintegrated Circuit, 7445573137547-001
180WIntegrated Circuit, 74FO4137437-001210RIntegrated Circuit, PR EPROM136077-1203
2108Integrated Circult, PR EPROM¥36077-1203
1s6YIntegrated Circuit, 7448573137547001210TIntegrated Circult, PR EPROM136077-1203
INCIntegrated Circuit, 7418393137146-0012HU(ntegrated Circuit, PR EPROM136077-1207
IKEIntegrated Clrewit, 744500337480-001210VIntegrated Circuit, PR EPROM13607-1209
190KIntegrated Circuit, 68010137414-002210Integrated Circuit, PR EPROM13607-1011
210Xintegrated Circult, PR EPROM36077-1013
2)0YIntegrated Circuit, PR EPROM136077-1015,

4-32

Page 107

Race Drivin’ Musteated Parts Lises

Race Drivin’ Main PCB Assembiy Parts List, Continued Desigoator Description Part No. Designator Description Part No. The following 16 program chips are for British Capacitors

right-hand-drive sinulators only:clCapachos, 100 pF, 35 V, Electrolytic-124000-107
200%Integrated Circuit, PR EPROM13607-2002czCapacitor, .01 WF, 50 V, Ceramic122002-103
2008Incegrated Circuit, PR EPROM136077-1104€3-C43_—Capacitor, .1 HF, $0 V, Ceramic122002-104
orIntegrated Circuit, PR EPROM136077-1106CA4063Capacitor, OO UF, 50 V, £1046122015-102
2000Integrated Circuit, PR EPROM13607-100864078Capacitor, .1 pF, 50 V, Ceramic122002-104
200vintegrated Circuit,PR EPROM136077-101079Capacitor, 10 pF, 100 V, Ceramic122016-200
2O0WIntegrated Circuit, PR EPROM13607-1112C80-C82Capacitor, .1 WF, 90 V, Ceramic¥22002-104
200XIntegeated Circuit, PR EPROM136077-1014
OYIntegetted Circuit, PR EPROM13607-1016C83, C#4Capacitor, 100 pF, 100 V, Ceramic122016-101
C85-C87_—Capacitor, .1 1B, 50 V, Ceramic122002-104
F10RIntegrited Circuit, PR EPROM136077-2001€88-C91Capacitor, .22 pF 50 V, Ceramic122015-224
2108integrated Cizcutt, PR EPROM13607-1103cozCapacitor, .t pF, 50 V, Ceramic122002-104
20Integrated Circuit, PR EPROM13607-1105
nouInsegrated Circult, PR EPROM136077-1007CoB,Capacitor, 10 jOF, 35 V, Electrolytic124000-106
210VIntegrated Circuit, PR EPROM13607-1009C94-C106 Capacitor, .t UE, 50 V, Ceramic122002-104
2108Integrated Circuit, PR EPROM136077-1111C108-C111 Capacitor, .22 pl, 50 V, Cemmic222015-224
240XIntegrated Circuit, PR EPROM13607-1013,€112-C11B Capacitor, .1 WF, 30 V, Ceramic122002-104
20yintegrated Circuit, PR EPROM136077-1015
cil9Capacitor, 3900 pF, 50 V, Ceramic122020-392
The following 16 program chips are for Japanese120Capacitor, 560 pF, 50 V, Ceramic122020-561
right-hand-drive simulators onty;ci2tCapacitor, 10 LF, 35 V, Hectrolytic124000-106
200KIntegrated Circuit, PR EPROM13607-1402C122Capacitor, 0022 pF, 100 V, Plastic121022-222
2008Integrated Circuit, PR EPROM.13607-1404
20T—sEntegrated Circuit, PR EPROM.13607-1406123Capacitor, .3 YF, 50 V, Ceramic22002-4104
200U136077-1408124Capacitor, .1 BF, 50 V, Ceramic122002-104
20Ovintegrated Circuit, PR EPROM13077-1410C125-C128 Capacitor, 10 WE, 35 V, Electrolytic124000-106
20OWIntegrated Circuit, PR EPROM13607-1412€129-C137 Capacitor, .1 j1F, 50 V, Ceramic122002-104
200KIntegrated Cirewit, PR EPROM13607-1414
2OYIntegrated Circuit, PR EPROM136077-1416e138Capacitor, 1000 pP, 100 V, Ceramic122016-402
139Capacitor, 1000 pF, 100 V, Ceramic12016-2102
210RIntegrated Clreuit, PR EPROM13607-1491c14oCapacitor, .t UE, 50 ¥, Ceramic122002-104
2108Integrated Circuit, PR EPROM13607-1403C14Capacitor, -1 WF, 50 V, Ceramic122002-104
norIntegeated Circuit, PR EPROM136077-1405
210UIncegetted Circuit, PR EPROM136077-1407C142Capacitor, 22 HF, 30 V, Ceramic122015-224
210¥integrated Circuit, PR EPROM136077-1409C143Capacitor, .1 AF, 50 V, Ceramic122002-104
210WIntegrated Circult, PR EPROM136077-1411cidC2pacitor, .1 HF, $0 V, Ceramic122002-104
210XIntegrated Circuit, PR EPROM13607-1413C145Capacitor, 10 pF, 35 V, Electrolytic324000-106
2107Integrated Circuit, PR EPROM136077-1415,

CH46-C227 Capacitor, .1 WF, $0 V, Ceramic 122002-104

C228Capacitor, .001 uF, 50 V, £10%122015-102
2058Integrated Circuit, 40668337580-001C229Capacitor, 47 p®, 100 ¥, Ceramic122036-470
210AIntegrated Circuit, MC1488137403001230-0249 Capacitor, .1 4LF, $0 V, Ceramic122002-104
2308Integrated Circult, MC1489AL,137263-003
210Integrated Clreuit, RAM, 8Kx8, 150 nsec 137535-006.C250Capacitor, 47 pF, 100 V, Ceramic122016-470
20DIntegrated Circuit, RAM, 8KXxB, 150 nsec 137535-006C251-C274 Capacitor, .F ME, 50 V, Ceramic122002-104
c274Capacitor, 47 p®, 100 V, Ceramic122016-470
200EIntegrated Circuit, 49202-15, RAM137442-150275-320 Capacitor, .1 UF, 50 V, Ceramic122002-404
2u0EIntegrated Circuit, 741524513714-0004
20HIntegrated Circuit, 7415244137038-001,C322Capacitor, 10 uF, 45 ¥, Electrolytic124000-106
2a)Integrated Circuit, 7415244137038-001€323-€326 Capacitor, 10 pP, 100 V, Ceramic122016-100

€330-C333 Capacitos, .1 HF, $0 V, Ceramic 122002-104

0Kintegrated Circuit, 7418244137038-001C335Capacitor, 100 pF, 100 V, Ceramic122016-101
2408Integrated Circuit, 7418245137134001
210MIntegrated Circuit, 74182431371340010336Capacitor, 100 pF, 100 V, Ceramic122016-101
2ONIntegrated Ciecwit, 7418244137036-001€337-C342 Capacitor, .1 pF, 90 V, Ceramic122002-104
210P137134001C344-C346 Capacitor, .1 RF, 50 ¥, Ceramic¥22002-104
C347Capacitor, 10 pF, 35 V, Elecuolytic—-124000-106

The last 13 pages are left out of this plain copy. The reader at this address has every page; it needs JavaScript.