CATHODE RAY TOMES

Centipede DP-182-4th-02A

Centipede (revision 4) (Atari, 1980) · Drawing Package · 1 pages · original scan

Page 1
Scan of page 1

From MPU ‘Address Bus

Sheet 1, Side B

ble

Centipede Playfield RAM Testing the Playfield RAM

  • Perform theCAT Box preliminary setup. 3

2. Set the CATBox switches as follows:

Prose TESTER RESET BUS SCURGE TO ADDR BYTES te 1026 4 IW MODE to (OFF) AW to WRITE Key in 000, Set FIW HODE to PULSE, then to OFF. FAW to READ. Set FIW MODE to PULSE, then to OFF.

TolFrom MPU ‘Data Bus Sheet #, Side @ Fermanee.

From Syne Generator

Playfield Address Selector

‘The Playfield Address Selector controls the access to the playfield memory. Hallows elther the game MPU or the sync generator to scan the playfield mem: ‘ory. The Playfield Address Selector consists of multiplexers P5, and PT and gate Ka,

When 3H on pin 1 of PS and P7 is low and pin 15 on P7 is low, the Playfield ‘Address Selector receives BH, 16H, 32H, and 64H on PS and 16V, 32V, 64, and ‘28V on P7 from the sync generator. These signals enable the sync generator Circuits to access the playfield memory.

When 3Fi goes high the game MPU addresses the playfield memory (via ‘AB0-AB9) for the positioning of the graphics. During Norizontal blanking (pin 15 ‘of P7 is high) the outputs of P7 (PFAS-PFA7) are held high enabling the motion ‘object circuitry to access the playfield memory for the motion objects to be displayed.

Centipede”

Playfield Memory Playfield Multiplexer Picture Data ROM Circuitry Motion Object Circuitry (Vertical) Motion Object Circuitry (Horizontal)

Section of 03724101 G

Ove commen corny Dosis ah printing Centpese It te CAT Box reads an address that doesn't compare, the COM: PARE ERROR LEO lights, the ADDRESSISIGNATURE display ‘shows the failing address location, and the ERROR DATA DIS- PLAY switch is enabled, It the COMPARE ERROR LED does not light, rekey 0400 and reppeat the test with the DBUS SOURCE switch set to ADDR. This fengures that the data bits at address 0400 will go high. If the ‘COMPARE ERROR LED does not light after this step, the Playfield RAM is good. Playfield Multiplexer “The Playfield Multiplexer receives playfield data from the playfield memory From Syne | sme (PFDO-PFO3!) and the output (PFO-PF?) is a code that determines what Is 1) dis- Generator Played on the monitor, or2) read or updated by the MPU. The Playfield Multiplexer ‘Sheet 1, Side ‘consists of select multiplexers K6, L6, M6, NG and P6. \When 256H is low and 4H is high, AB4 and ABS from the MPU address bus is the ‘solected output from PS. This output is applied to multiplexers K6, L6, M6, and NE as select inputs. When the MPU is accessing the playfield code muitiplexer, the playfield datas either being read or updated by the MPU. When 256H is high and 4H {is low, the inputs from the sync generator (128H and BV) are the selected outputs, These signals then select which bits of data PFOO-PFDS1 are sent out via K6, L6, 'M6, and N6 for the playfield codes that eventually are displayed on the monitor,

‘The playfield codes (PFO-PF7) are latched by JS and J6 to the MPU data bus (J5) ‘and to the picture data PROM circuitry (J6). When PFRAMIAD is low and 1H from the syne generator goes high, the inputs on J5 (PFO-PF7) are latched out to the MPU via (DB0-D87. When 4H on pin 11 of 16 goes high, the inputs (PFO-PF7) are latched to the picture data PROM circuitry |

From Syne Generator ‘Sheet 1, Side 8 Motion Object Circuitry (Vertical)

The Motion Object Circuitry (vertical) receives playtield data and vertical inputs from the ‘syne generator circuitry to generate the vertical component of the motion object video. PFOS- 1 from the playfield memory and 1V-128V from the sync generator are compared at F6 and HB. ‘The output is gated by A7 when a motion object is on one of the sixteen vertical ines and is latched by EB to AND gate B7. A low on 87 pin 8 indicates the presence of a motion object on, tone of the vertical lines during non-active video time, This signal (MATCH) enables the multplexers in the picture data circuitry. When 256H on pin 1 of 07 goes high, 1V,2V, 4V and PICO are selected. When 256H goes low, the latched output of E6 is selected. The output of D7 is EXCLUSIVE OR gated at E7 and is sent to the picture data selector circuitry as motion graphic address (MGAO-MGAS). The other input to EXCLUSIVE OR gate E7 Is PICT from the playfield code multiplexer circuitry. PICT when high causes the output of £7 to be complimented. For example, if MGAO-MGAS are ow, PICT causes MGAO-MGAS to go high. This causes the motion object viceo to be inverted top to bottom, Motion Object Circuitry (Horizontal)

‘The motion object circuitry (horizontal) receives playfield data and horizontal inputs trom the sync generator circuitry. PFD16-PFD23 from the playfield memory determine the horizontal position of the motion object. PFO24-PFD29 from the playfield memory determine the indirect ‘color of the motion object. PFD16-PFO23 are latched by 64 and loaded Into the horizontal position counters AS and BS by a iow on pin 9. The horizontal position counters then address video RAMs A6 and 88. These RAMS are loaded with the video data from the particular motion ob- Ject from shift registers H9 and J9 (which were loaded from the graphics ROM), The output for RAMs A6 and B6 is then sent to the color PROM circuitry as MRO and MR. Picture Data ROM Circuitry

‘The picture data ROM circuitry receives picture information, assigns a color code to the information and sends it to the color PROM circuitry. The picture data ROM circuitry consists of ROM devices F7 and 'HU7, multiplexers FB, H8, J8, KB, shift registers HO and J8, and fateh F9.

‘The picture ROMs receive (PICO-PICS) from the Playfield. code multiplexer, MGAOMGAS (motion graphics address) from the motion object circuitry, £256H and 256H from the syne generator. PICO-PICS represent the code for the object to be displayed MGAG-MGA3 set one of eight different combina tions of the Bline by B-it blocks of picture video or the T6:line by B-bit Blocks of motion object video.

256H when high selects the playtied picture colfor codes to be addressed. 256H when low selects the motion object color codes to be addressed. The picture data ROM output DO-D7 on F7 and HIJ7 are ‘multiplexed by F8, H8, JB and KB and shifted out ser ially at H9 and J9, This serial output is latched by FO {as AREAO and AREAI to the motion object horizon: tal circuitry and the video output circuit.

From Syne Generator ‘Sheet. Side 8