CATHODE RAY TOMES

Break Thru Conversion Kit

Break Thru (World) (Data East Corporation, 1986) · Kit Manual · 11 pages · 7 sections · original scan

Page 1

CONVERSION KIT

installation « service manual

fa DATA EAST USA, INC. ) wg 470 Needles Drive San Jose, CA 95112

780-0036-00

Page 2

WARNING

This equipment generates and uses radio frequency energy and if not installed and used properly, i.e., in strict accordance with the instructions manual, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device persuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.

Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

Page 3

Thank you for purchasing this Data East Conversion Kit. Your kit includes the following: 510-0061-00 PCB ASSEMBLY, BREAK THRU 520-0083-00 PCB ASSEMBLY, EMI FILTER DE-0239 450-0009-00 JOYSTICK, 4/8 WAY 185-0001-00 PUSHBUTTON HOLDER WITH SWITCH 240-0001-00 PAL NUT 850-0001-02 PUSHBUTTON, SHORT, RED 850-0001-04 PUSHBUTTON, SHORT, YELLOW 350-0001-00 PUSHBUTTON, SHORT, BLACK 830-0020-00 MARQUEE PLEX, BREAK THRU 800-0019-00 CONTROL PANEL OVERLAY, BREAKTHRU 820-0029-00 SIDE DECAL, BREAK THRU 810-0014-00 UNDERLAY CARD, MONITOR, GENERIC 406-0029-00 LABEL, INSTRUCTIONS, BREAK THRU 820-0028-00 DECAL, LOGO, UNDERLAY CARD 036-0013-00 HARNESS, MAIN GENERIC KIT 780-0036-00 INSTALLATION & SERVICE MANUAL 406-0003-00 LABEL, FCC lll <n CeCe. oer oer ey

TABLE OF CONTENTS

IMPORTANT WARRANTY INFORMATION. ......0c0cececccececcececeeecd ADJUSTMENTS & OPTIONS

A. Volume Control... ee. e eee eee eee cece eens cccecece +2

B. Operator Selectable Options......... cece cece cece eed

CONVERSION SUMMARY... 2... .... eee cee eee eccceceenen eed COSMETICS... 020s sees eee e cece cece eecetecteeseecceeceecsecd

INSTALLATION INSTRUCTIONS

A. General Instructions... ....... cece cc cece cece ceeeeee 5

B. Wiring Harness Diagram... 2... eee cece cece cece eee 6

C. Specific wiring Procedures......... ec. cece eee eee eee

DATA EAST USA INC. 470 NEEDLES DR. SAN JOSE, CA. 95112

Page 4

1, IMPORTANT WARRANTY INFORMATION

LIMITED WARRANTY

Data East USA, Inc. ("Seller"), warrants only to the initial purchaser of its products that the items listed below are free from defects in material and workmanship under normal use and service for the warranty periods specified:

  • Printed Circuit Boards (Game Logic) (90) days

No other parts of the Seller's products are warranted.

Warranty periods are effective from the initial date of shipment from Seller to its authorized distributors.

Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

  • Seller is notified promptly upon discovery by buyer that stated products are defective.
  • Such products are properly packaged and then returned, prepaid to Seller's plant.

This warranty does not apply to any parts damaged during shipping or handling, or due to improper installation or usage, or alteration. In no event shall the Seller be lable for any anticipated profits, loss of profits, loss of use, incidental or consequential damages or any other losses incurred by the customer in connection with the purchase of a Data East USA, Inc. product.

WARRANTY DISCLAIMER

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND PURCHASER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Page 5
  • ADJUSTMENTS & OPTIONS

A. VOLUME CONTROL. The audio volume is adjustable via a trimpot (VR1) on the CPU PCB.

B. OPERATOR SELECTABLE OPTIONS. The Operator Selectable Options can be altered by changing the settings of the Dip Switches found on the CPU PCB. Table 1 and Table 2 outline the available options.

DIP SWITCH 112345678
COIN1 COIN=1 CREDITOFF OFF

vs 1 COIN = 2 CREDIT ON OFF CREDIT OFF ON CREDIT ON ON CREDIT 1 COIN = COIN 1 2 COIN =

COIN1 COIN = 1 CREDITOFFOFF
VS1 COIN = 2 CREDITONOFF

CREDIT 1 COIN = 3 CREDIT OFF ON

COIN 2 2 COIN = 1 CREDITONON
CONTROL PANELTABLEOFF
UPRIGHT.oN

CABINET TYPE TABLE OFF UPRIGHT on

BONUS20000/30000 PTSOFFOFF
LIVES20000/40000 PTSONOFF
10000/20000 PTSOFFON
20000/ NONEONON

MONITOR NORMAL OFF

PICTURE FLIP ON

Page 6
  • CONVERSION SUMMARY

One of the most important considerations determining the success of your conversion will be the condition of the machine you are converting. Obviously, if the monitor is dull in the original game, it will be no better with the conversion installed. If you have a choice, select a Machine that has an instruction manual and/or good primary wiring diagrams. You MUST select a machine that has previously been certified as conforming to Part 15, Subpart J, of the FCC regulations. It it mandatory that the primary wiring contain a good noise filter in order to prevent conducted radio frequency interference.

Since it is extremely important that all visible graphics, original manufacturer's name (other than the Serial Number tag), logo's, ete., are to be removed or covered by new graphics, a proper choice of cabinet in this phase of the conversion will save you much time.

Make sure that the integrity of the cabinet is such that the converted game will not be a vandals dream. Review the control panel to identify what changes will be required so that you will be prepared. It may be necessary to drill holes in the control panel for pushbuttons, etc. before applying the new overlay. See figure 1 for Suggested control layout.

The BREAK THRU game is designed to Operate with a COLOR RASTER MONITOR, mounted in a HORIZONTAL position. The BREAK THRU PCB generates NEGATIVE COMPOSITE SYNC. The POWER SUPPLY requirements are: +5 volts @ 7 Amperes, and +12 volts @ 1 Ampere.

It is mandatory that the cabinet be wired to conform with all National and Local Electrical Code requirements before the conversion is attempted. The system must have adequate noise filtering on the AC line to prevent unwanted conducted radio frequency interference. “Adequate” is defined as a filter having both common mode and differential mode filtering with a current capacity of at least 1 1/2 amperes.

According to the FCC and various other agencies, every video game must be clearly and permanently LABELED with the name and address of the Original Manufacturer, Date of Manufacture (or serial number), Voltage rating, Current rating, Suitability for indoor or outdoor use, and unit model number. In addition, the FCC requires that, after conversion, the unit Must be labeled with a suitable warning stating that radio frequency interference may result from use in a residential area. An acceptable

warning sticker is enclosed, in your kit. IT IS THE RESPONSIBILITY OF THE INDIVIDUAL PERFORMING THE CONVERSION TO INSURE THAT ALL LABELING REQUIREMENTS ARE CONFORMED WITH!
Page 7
  • COSMETICS

All components that contain the Original Manufacturer's name (other than the serial number plate), graphics, logos, or game play information must be removed or covered by some means. Do not destroy the Display Plex or the Control Panel as these items may have to be used or modified for your conversion.

A cardboard underlay has been provided to be placed under a clear Display Plex. You will install the game instruction decal on to this underlay card. If the existing Display Plex has silkscreened artwork on it, you will need to strip it clean (lacquer thinner is usually effective) or replace it with a clear plex. If necessary, trim the cardboard underlay, with a razor blade, down to the size of the Display Plex. Install the Instruction Decal and the Underlay Logo Decal as shown in figure 2.

The control panel overlay supplied in this kit is designed to allow the player controls to be placed in a variety of positions. First, strip off the original controls and the overlay and then thoroughly clean and deburr the control panel. If necessary, drill out any required holes in the control panel. The new overlay has a strong adhesive on one side of it, so be sure you know how you want it positioned before peeling off the paper backing and applying it to the panel. When applying the overlay, smooth it out from the center to the edges, being sure remove all trapped air bubbles. Trim any excess material, and material from mounting holes, with a razor blade or sharp knife.

A new 8 way joystick is provided with the kit. Appropriate color pushbuttons, button holders, and pal nuts are supplied. The pushbuttons require a 1 1/8 inch diameter mounting hole.

TPLYR Jum ©) © « a@) Cs) (4P s2) (1P $1) Den $1) OP $2)

FIGURE 1. RECOMMENDED CONTROL PANEL LAYOUT

Page 8
  • INSTALLATION INSTRUCTIONS

A. General Instructions

Your conversion kit has been supplied with a main harness which connects the EMI Filter/Adaptor PCB to the various places in the game in which you are converting. Each wire has been labeled as to its function. If in doubt, refer to the Main Harness Diagram on page 6.

  • Follow all instructions in this manual relating to selecting a game to install this conversion into.
  • Mount the new Logic PCB set in-a convenient--location:~ An EMI cage is not necessary for this conversion, but the use of the EMI Filter/Adaptor PCB is MANDATORY!
  • Plug the EMI Filter/Adaptor PCB into the BREAK THRU PCB as shown on page 6.
  • Plug the Generic Main Harness onto the EMI Filter/Adaptor PCB.
  • Neatly route all of various main harnessing around the cabinet to the proper destination points and terminate as required. Refer to the Specific Wiring Procedures on page 7 for details.
  • When you are certain that you have made all the connections properly, turn on the main power and wait for the monitor to warm up. Watch for any signs of smoke or cracking noises indicating a problem. You may have to adjust your monitor to center the picture or enhance the colors. MEASURE AND ADJUST THE +5 VOLT POWER SUPPLY AT THIS TIME!

When you have finished converting your game, be sure to attach the FCC

WARNING label to the rear of the cabinet. Failure to do so is a violation of the FCC regulations.

LOGO DECAL

HORIZONTAL

MONITOR

INSTRUCTION DECAL

FIGURE 2. APPLYING THE INSTRUCTION AND LOGO DECALS TO THE UNDERLAY CARD.

Page 9

B. Main Harness Wiring Diagram

COMPONENT SIDE SOLDER SIDE

WIRE;Pin Nos"WIRE
coLoretenslKELeignalCOLOR
GRNBI1P__DOWNA_|Al2P__DOWN
yeu [2 [B2 |1P UP.B[A22P__UP
ORG3 | B31p LEFT[c [a32P__LEFT
reo [4 [Ba1P__RIGHT.Daa |2P__ RIGHT.
51p sHooT 3|2P__ SHOOT 3

F 7 H 8 =a

BLU91P_SHOOT 1!K2P SHOOT 1
vio.[10 |B10| 1P SHOOT 2|2P_SHOOT 2

BRN 11 [Bil { 1P GAME SELECT | M jail | 2P GAME SELECT | RED/WHT

GRNCOIN 1lz | COIN 2RED
v0COIN COUNTER |Als | COIN COUNTER 2 | GRY
BLU/WHTTV.BR [aldTV.GGRN/WHT
war/ark[18 [BISSYNC.S_ [AisTV.RRED/WHT

16 [B16 T [a6

wit[17 [Bi7]| SPEAKER +U_|A17 | SPEAKER —BLK/HHT
orc[18 [B18+12Vv_fare= VBLU
reo[19 [BI9+5Vw {arg+5VRED
+3Vx [Azo+5VRED
[agt |GNDeLK

GND

Page 10

Cc. Specific Wiring Procedures

GRN 1P DOWN [e> veL fs2> re) 1P UP RG [es> 1° LEFT = 1P RIGHT [ea> 1p START 2P START

IP SHOOT 1 (RED)

IP SHOOT 2: CYeUaN)

Gx - GROUND

CONTROL. PANE

+12V

COIN COUNTER |

ON COUNTER 2

H2V

CON COUNTER |

CON conTeR 2 [13>

spaner + [a> ly an/wnr BOW, SWATT SPEAKER speamen — [a7 >

CON I

CON 2

GROUND

COIN MECR DOOR,

Page 11

WARNING

Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.

The Federal Bureau of Investigation

investigates allegations of criminal copyright infringement.