CATHODE RAY TOMES

Mr Viking Field Conversion Kit (M051-00A93-A012)

Mister Viking (315-5041) (Sega, 1984) · Field Conversion Kit · 48 pages · 31 sections · original scan

Page 1

SS

MR. VIKING

FIELD CONVERSION KIT

FROGGER, ZAXXON and UP’N DOWN

Coll MIDWAY MFG. CO. 10601 W. Belm: Franklin Park, whine ie e019! U.S.A, Phone: (312) 451-9200 Cable Address: MIDCO Telex No.: 72-1596

MO5 1-00A93-A012

Page 2
WARNING THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
WARNING: This equipment generates. uses. and can radiate radio frequency energy and if not and used in accordance with the instructions manual. may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J of PART 15 of FCC RULES. which are designed to provide reasonable protection against such interference when operated in acommerical environment. Operation of this equipment in a residential area Is likely to Cause interference in which case the user at his own expense will be required to lake whatever measures may be required to correct the interterence

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT

Vuuites You Te Use ouR TOLL FREE numese_ers For

SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY MIDWAY GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS

ANSWERS TO YOUR PROBLEMS. VIDEO === Continental U.S. 1-800-323-7182 PINBALL == Continental U.S. 1-800-323-3555 MIDWAY 1001 west sermons avenue. Frankiin Bork, Inn's, 80191 phone 12481-8200 af

© COPYRIGHT MCMLXXXIV BY BALLY MIDWAY MFG. CO. ALL RIGHTS RESERVED

NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: BALLY MIDWAY MFG. CO., 10601 W. BELMONT AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.

Page 3

TABLE OF CONTENTS

DESCRIPTION PAGE

General CONVErSiOn cesssccecccccncnccccrccsevereesecssssscseesscesesccoses |

Zaxxon to Mr. Viking CONVErSION ceccccccccrccccccerececccansssecccesceeees 2

Warning about Frogger to Mr. Viking Conversion ..ccecccccccccsccceecsccecs Od

Frogger to Mr. Viking CONVErsiONn ..cccccececccccccsccccccccercsseseesscses ©

er) Up'N Down/Mr. Viking Conversion from Zaxxon/Up'N Down Conversion ...

Up'N Down/Mr. Viking Conversion from Frogger/Up'N Down Conversion ......56 14

Up'N Down to Mr. Viking Conversion ...csceeccccccccecccccccsecccscscereces 20

Monitor Modification Section ssscecccessccccccccceccccccnsssccscscsesssees 29

Decal Installation Instructions ..sccccccccccccecccsececccscvccsccessccese 26

Page 4

TABLE OF ILLUSTRATIONS

ILLUSTRATION PAGE

Zaxxon to Mr. Viking Conversion Before & After Views of P.C.B. Conversion sssecccececcseceececeee 3 Control Panel Overlay Application Instructions ...... ween 4

Frogger to Mr. Viking Conversion Header Conversion .esseccccccscecccccrcececccctcsscccscccesscsses | Before & After Views of P.C.B. Conversion . soe 7

Up'N Down/Mr. Viking Conversion from Zaxxon/Up'N Down Conversion Control Panel Overlay Application Instructions ...secececcceceees 10

Mr. Viking Logic P.C.B. Parts Locations . ceeeeee Ll Before & After Views of P.C.B. Conversion .e.scececccecccecncceee 12

Up'N Down/Mr. Viking Conversion from Frogger/Up'N Down Conversion Control Shelf Conversion ...secccscccsccere eee coos 15 Mr. Viking Logic P.C.B. Parts Locations ws... 16 Header Conversion seesceseccccccccvccsccevcees Before & After Views of P.C.B. Conversion .. Joystick Assembly & Wiring Instructions ...... seceecereccceees 18

Up'N Down to Mr. Viking Conversion Mr. Viking Logic P.C.B. Parts Locations ..ccccccccvccccccccecceee 2b Instructions for Control Shelf Conversion ...csvccceceereccceeere 22

Monitor Modifications Section Drawing #1 - Electrohome - Yoke Wires Soldered in Place at Both Ends ..cecececccerecccccerscsccceresesereves 20a Drawing #2 - Electrohome - Yoke Wires Plugged into the Monitor's P.C. Board ...seccseccccccscccccecsceceses 25D Drawing #3 - Wells Gardner - Yoke Wires Plugged Directly UNtO the YOKE ceccscccceccccccccccscecceccssvscesees LC

Page 5

WR. VIKING

FIELD CONVERSTON KITS

GENERAL :

The basic purpose of this instruction sheet is to give you some simple guide lines for converting your ZAXXON, FROGGER and UP'N DOWN games to MR. VIKING games.

Turn your game OFF, unplug it from it's power source, and open all its access doors.

NOTE: Refer to the attached "BEFORE" and "AFTER" drawings to help you identify the varfous parts talked about in this Instruction Sheet.

051 -00A93-A012

Page 6

10. ~2-

ZAXXON To MR. VIKING CONVERSION

Disconnect and remove the ZAXXON game boards and set them aside.

Relocate the games Power Supply as shown, observing the critical measurements pointed out in the AFTER drawing.

Relocate the game's Self-Test Switch Assembly as shown in the AFTER drawing.

Install the NEW game board as shown in the AFTER drawing and connect it to it's cabling.

Remove the screws from the Header Retaining Bracket and replace the Header.

Remove your old Control Panel, modify it as shown in the following illustration,

MODIFY YOUR GAMES WIRING AS FOLLOWS:

A. Insert one end of the 39" long BLACK wire into pin 8 of the 44 position Edge Connector of the Logic P.C. Board. Insert the other end of this 39" long BLACK wire into an open pin of the cabinet cable harnes half of the Control Panel Universal Cable Connector.

Insert one end of the 23" long BLACK wire into the mating open pin of the Control Panel cable harness half of the Control Panel Universal Cable Connector.

Locate the 14" long BLACK wire. Now twist one end of this wire together with the free end of the above 23" long BLACK wire and solder them both to the TOP TAB of the Fire Button. —

The other end of the 14" long BLACK wire is to be soldered to the TOP TAB of the Second Fire Button. _

Take one of the two 4" long YELLOW/BLACK wires and solder one end of this wire to the BOTTOM TAB of the Fire Button. Now solder it's other end to the wire that is common to all switches.

Take the remaining 4" long YELLOW/BLACK wire and solder one end of this wire to the BOTTOM TAB of the Second Fire Button. Now solder it's other end to the wire that is common to all switches.

Install the Decals provided with your Conversion Kit OVER those currently on your game. See the Decal Installation Instruction Section of this booklet.

Install the Game Play Instruction Label on the Main-Display-Glass in a manner so as not to block the players view of the game.

Secure your games access doors, reconnect it to it's power source, turn it ON, and check to see if your picture appears. upside down and reversed.

Page 7

BEFORE

POWER SUPPLY ; RELOCATED ON | LEFT SIDE

TEST SWITCH BRKT. NEW GAME BOARO

POWER SUPPLY FRONT OF GAME OPEN TEST SWITCH BRKT. RELOCATED ON RIGHT SIDE

Page 8

CONTROL PANEL OVERLAY APPLICATION INSTRUCTIONS

REMOVE ALL CONTROLS

APPLY NEW OVERLAY AFTER REMOVING PROTECTIVE BACKING SHEET. ALIGN TOP 3 HOLES & WRAP OVERLAY AROUND ENDS PER SKETCH.

WITH SHARP KNIFE CUT OUT HOLES FOR PLAYER 1, PLAYER 2.

REASSEMBLE CONTROLS AS ORIGINALLY MOUNTED.

MO51-00A74-A012

Page 9

A. If it is 0.K., run a Self-Test and go on to Step 11 below.

B. If the picture is upside down and reversed, (LEFT is RIGHT and RIGHT is LEFT), go to the MONITOR MODIFICATIONS SECTION where it is explained how to correct this condition.

When through completing a positive Self-Test (everything checks good), your game is

  • ready for use.

LIST OF MAJOR PARTS

INCLUDED IN YOUR CONVERSION KIT

ZAXXON To MR. VIKING CONVERSION

PART NO. DESCRIPTION

ABO2-00002-0000 CONVERSION CABLE ASSY. A084-91743-AA94 INTERFACE BOARD ASSY. A084-91750-AA92 MR. VIKING LOGIC ASSY. M051-00A93-A012 CONVERSION KIT INSTRUCTION MANUAL M051-00A94-A009 GAME PLAY INSTRUCTION LABEL M051-00121-A010 SERIAL NUMBER LABEL 051-00122-0000 MANUAL REQUEST POST CARD 0A92-00300-0000 PARTS CATALOG - MR. VIKING OA93-00900-00XF : HEADER 0B07-00901-0100 CONTROL SHELF OVERLAY 0B07-00903-0100 RIGHT SIDE DECAL 0B07-00903-0200 LEFT SIDE DECAL

Page 10
  • 5a -
wARNING! !

THIS FROGGER TO MR. VIKING

CONVERSION KIT CAN ONLY BE USED

IN FROGGER GAMES HAVING A

SEPARATE POWER SUPPLY

M051-00A93-A013

Page 11

1.

NOTE:

8.

10.

11.

12.

13.

14. FROGCER T0 MR. VIKING CONVERSION

Disconnect and remove the FROGGER game boards and set them aside.

You may also want to remove the games Coin Door and Frame Assembly at this point to give you more room to work on the next several Steps.

Disconnect and remove the game's Control Panel (held in place by bolts with wing-nuts from underneath).

Remove the plywood panel the FROGGER game boards were mounted on.

Relocate the games Power Supply as shown, observing the critical measurements pointed out in the AFTER drawing.

Install the NEW game board as shown in the AFTER drawing and connect it to it's cabling.

Remove your games old Control Panel and set it aside.

MODIFY YOUR GAMES WIRING AS FOLLOWS:

A. Insert one end of a 39" long BLACK wire into pin 8 of the 44 position Edge Connector of the Logic P.C. Board. (The signal carried by this wire is PLAYER 1 FIRE.) Insert the other end of this 39" long BLACK wire into the open pin in the cabinet cable harnes half of the Control Panel Universal Cable Connector which will match up with the wire coming from the PLAYER 1 FIRE Button.

B. Insert one end of the second 39" long BLACK wire into pin 9 of the 44 position Edge Connector of the Logic P.C. Board. (The signal carried by this wire is PLAYER 1 BOMB.) Insert the other end of this 39" long BLACK wire into the open pin in the cabinet cable harnes half of the Control Panel Universal Cable Connector which will match up with the wire coming from the PLAYER 1 BOMB Button.

Install the Game Play Instruction Label over the current one on your game.

Remove the screws from the Speaker and Header Retaining Board as shown (it will drop down) and replace the Header.

Replace your games Control Panel Assembly with the NEW one provided in your Conversion Kit.

Reinstall the game's Coin Door and Frame Assembly if you removed it previously.

Install the Decals provided with your Conversion Kit OVER those currently on your game. See the Decal Installation Instruction Section of this booklet.

Secure your games access doors, reconnect it to it's power source, turn it ON, and check to see if your picture appears upside down and reversed.

A. If it is 0.K., run a Self-Test and go on to Step 14 below.

B. If the picture is upside down and reversed, (LEFT is RIGHT and RIGHT is LEFT), go to the MONITOR MODIFICATIONS SECTION where it is explained how to correct this condition.

When through completing a positive Self-Test (everything checks good), your game is ready for use.

Page 12

REMO\E 4 SCREWS TO DROP RETAINING BOARD

COIN DOOR & FRAME

POWER SUPPLY RELOCATED ON LEFT WALL

OLD GAME BOARDS

PLYWOOD PANEL

POWER SUPPLY

NEW GAME BOARD

SPACERS

BEFORE

Page 13

LIST OF MAJOR PARTS

INCLUDED IN YOUR CONVERSION KIT

FROGGER TO MR, VIKING CONVERSION

PART _NO. DESCRIPTION AB02-00002-0000 CONVERSION CABLE ASSY. A084-91742-AA93 INTERFACE BOARD ASSY. A084-91750-AA92 MR. VIKING LOGIC ASSY. AA93-00005-0000 CONTROL SHELF ASSEMBLY M05 1-00A93-A009 GAME PLAY INSTRUCTION LABEL M051-00A93-A012 CONVERSION KIT INSTRUCTION MANUAL M051-00121-A010 SERIAL NUMBER LABEL M051-00122-0000 MANUAL REQUEST POST CARD 0A92-00300-0000 PARTS CATALOG - MR. VIKING 0A93-00900-00XF HEADER 0B07-00904-0100 RIGHT SIDE DECAL 0B07-00904-0200 LEFT SIDE DECAL

Page 14

UP'N DOWN To MR. VIKING CONVERSION

FROM

ZAXXON CONVERTED TO UP'N DOWN

Disconnect and remove the UP'N DOWN game board.

Replace the EPROMS indicated in the following illustration with those provided in your Conversion Kit.

Install the NEWLY modified game board as shown in the AFTER drawing and connect it to it's cabling.

Remove the screws from the Header Retaining Bracket and replace the Header.

Remove and disassemble your Control Panel so that you can install the new Control Panel Overlay. (See the following illustration.)

Reassemble your Control Panel and modify it's wiring as follows so that the Joystick Trigger acts as a FIRE Button causing Mr. Viking to shoot arrows and the Push Buttons will cause him to throw Bombs, Missiles, etc.

CHECK TO SEE THAT YOUR GAMES WIRING CONFORMS TO THE FOLLOWING (MODIFY IT WHERE NEEDED):

A. Insert one end of the 39" long BLACK wire into pin 8 of the 44 position Edge Connector of the Logic P.C. Board. Insert the other end of this 39" long BLACK wire into an open pin of the cabinet cable harnes half of the Control Panel Universal Cable Connector.

B. Insert one end of the 23" long BLACK wire into the mating open pin of the Control Panel cable harness half of the Control Panel Universal Cable Connector.

C. Locate the 14" long BLACK wire. Now twist one end of this wire together with the free end of the above 23" long BLACK wire and solder them both to the TOP TAB of the Fire Button. —_—

D. The other end of the 14" long BLACK wire is to be soldered to the TOP TAB of the Second Fire Button.

E. Take one of the two 4" long YELLOW/BLACK wires and solder one end of this wire to the BOTTOM TAB of the Fire Button. Now solder it's other end to the wire that is common to all switches.

F. Take the remaining 4" long YELLOW/BLACK wire and solder one end of this wire to the BOTTOM TAB of the Second Fire Button. Now solder it's other end to the wire that is common to all switches.

Install the Decals provided with your Conversion Kit OVER those currently on your game. See the Decal Installation Instruction Section of this booklet.

Install the Game Play Instruction Label on the Main-Display-Glass in a manner so as not to block the players view of the game.

Page 15

CONTROL PANEL OVERLAY APPLICATION INSTRUCTIONS

REMOVE ALL CONTROLS

APPLY NEW OVERLAY AFTER REMOVING PROTECTIVE BACKING SHEET. ALIGN TOP 3 HOLES & WRAP OVERLAY AROUND ENDS PER SKETCH.

WITH SHARP KNIFE CUT OUT HUJLES FOR PLAYER 1, PLAYER 2.

REASSEMBLE CONTROLS AS ORIGINALLY MOUNTED.

MO51-00A74-A012

Page 16

VIKING

PART NUMBER

315-5041 316-5749 316-5750 316-5873 316-5874 316-5875 316-5876 316-5755 316-5756 316-5757 316-5758 316-5759 316-5760 316-5761 316-5762 316-5763 PARTS

DESCRIPTION

CUSTOM IC EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM LOCATIONS

1.C. NUMBER

aNQ900

Note ReNeteNetetetetate! HHH HHH RH HHH HH
Page 17

BEFORE

POWER POWER SUPPLY SUPPLY

OLD GAME BOARD TEST SWITCH BRKT. OLD GAME BOARD TEST SWITCH BRKT. WITH NEW EPROMS

FRONT OF GAME OPEN

Page 18

10.

11.

12. = 13 =

Install and secure your games modified Control Panel.

Secure your games access doors, reco mnect it to it's power source, turn it ON, check to see if your picture appears upside down and reversed.

A. If it is 0.K., run a Self-Test and go on to Step 12 below.

B. If the picture is upside down and reversed, (LEFT is RIGHT and RIGHT is LEFT), go to the MONITOR MODIFICATIONS SECTION where it is explained how to correct this condition.

When through completing a positive Self-Test (everything checks good), your game is ready for use.

LIstT

INCLUDED IN

uP'N DOWN TO OF MAJOR PARTS

YOUR CONVERSION KIT

MR. VIKING CONVERSION

FROM

ZAXXON CONVERTED T0 UP'N DOWN

PART NO.

ABO2-00002-0000 A084-91743-AA94 M05 1-00A92 -A012 M051-00A93-A012 M05 1-00A94 -A009 M051-00121-A010 M051-00122-0000 0A92-00300-0000 0A93-00900-00XF 0B07-00903-0100 0B07- 00903-0200 0B07-00901-0100 Q315-05041-0000 0A92-00803-0001 0A92-00803-0002 0A92-00803-0003 0A92-00803-0004 0A92-00803-0005 0A92-00803-0006 0A92-00803-0007 0A92-00803-0008 0A92-00803-0009 0A92-00803-0010 0A92-00803-0011 0A92-00803-0012 0A92-00803-0013 0A92-00803-0014 0A92-00803-0015 DESCRIPTION

CONVERSION CABLE ASSY. INTERFACE BOARD ASSY. LOGIC BOARD LABEL CONVERSION KIT INSTRUCTION MANUAL GAME PLAY INSTRUCTION LABEL SERIAL NUMBER LABEL MANUAL REQUEST POST CARD PARTS CATALOG - MR. VIKING HEADER RIGHT SIDE DECAL LEFT SIDE DECAL CONTROL SHELF OVERLAY CUSTOM I.C. EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM

Page 19

9. UP'N DOWN TO MR. VIKING CONVERSION

FROM

FROGGER CONVERTED TO UP'N DOWN

Disconnect and remove the UP'N DOWN game board.

Replace the EPROMS indicated in the following illustration with those provided in your Conversion Kit.

Install the NEWLY modified game board as shown in the AFTER drawing and connect it to it's cabling.

Remove the screws from the Speaker and Header Retaining Board as shown (it will drop down) and replace the Header.

Remove your old Control Panel.

Remove the Joystick from your old Control Panel and install it in the Control Panel provided with your Conversion Kit. (See the following illustration.) It is wired in an identical manner to it's previous wiring.

CHECK TO SEE THAT YOUR GAMES WIRING CONFORMS TO THE FOLLOWING (MODIFY IT WHERE NEEDED):

A. Insert one end of the 39" long BLACK wire into pin 9 of the 44 position Edge Connector of the Logic P.C. Board. Insert the other end of this 39" long BLACK wire into an open pin of the cabinet cable harnes half of the Control Panel Universal Cable Connector.

B. Insert one end of the 23" long BLACK wire into the mating open pin of the Control Panel cable harness half of the Control Panel Universal Cable Connector.

C. Locate the 14" long BLACK wire. Now twist one end of this wire together with the free end of the above 23" long BLACK wire and solder them both to the TOP TAB of the Bomb Button.

D. The other end of the 14" long BLACK wire is to be soldered to the TOP TAB of the Second Bomb Button.

BE. Take one of the two 4" long YELLOW/BLACK wires and solder one end of this wire to the BOTTOM TAB of the Bomb Button. Now solder it's other end to the wire that is common to all switches.

Fs Take the remaining 4" long YELLOW/BLACK wire and solder one end of this wire to the BOTTOM TAB of the Second Bomb Button. Now solder it's other end to the wire that is common to all switches.

G. After’ performing the above, you still have 4 wires left in your Conversion Kit. Two of which are BLACK and 14" long and two of which are YELLOW/BLACK and 4" long. These may be used to jumper the Fire Buttons on your Control Panel together and to connect them to the Center Fire Button on your joystick.

Install the Decals provided with your Conversion Kit OVER those currently on your game. See the Decal Installation Instruction Section of tnIs booklet.

Install the Game Play Instruction ' ibel over the current one on your game.

Page 20

CONTROL SHELF CONVERSION

Page 21

MR. VIKING PARTS LOCATIONS

DRAWING PART NUMBER NUMBER DESCRIPTION I.C. NUMBER

2 315-5041 CUSTOM IC I.C. 125 3 316-5749 EPROM I.C. 86 4 316-5750 EPROM Ic. 93 5 316-5873 EPROM I.C. 129 6 316-5874 EPROM I.C. 130 7 316-5875 EPROM I.c. 131 8 316-5876 EPROM Ic. 132 9 316-5755 EPROM I.C. 133 10 316-5756 EPROM IC. 134 11 316-5757 EPROM I.C. 63 12 316-5758 EPROM I.c. 80 13 316-5759 EPROM I.C. 64 14 316-5760 EPROM I.c. 81 15 316-5761 EPROM I.C. 65 16 316-5762 EPROM I.C. 82 17 316-5763 EPROM I.c. 3

Page 22

POWER SUPPLY POWER SUPPLY

OLD oa GAME BOARD

SPACERS

BEFORE PLYWOOD PANEL

OLD GAME BOARD WITH NEW EPROMS SPACERS REMOVE 4 SCREWS TO DROP RETAINING BOARD

JOYSTICK

COIN DOOR & FRAME

AFTER

Page 23

~ 18 -

JOY STICK ASSEMBLY & WIRING INSTRUCTIONS

FROGGLE TO UP'N DOWN CONVERSION KIT PUSH BUTTON ROD

BALL & SHAFT aN SPRING

SLIDE PLATE

BASE

SPRING

NYLON ACTUATOR BUSHING

"E" RING SWITCH ASSY.

‘ACTUATOR PLATE

ASSEMBLY INSTRUCTION

YOUR K11 COMPS WITH IHi JOYSTICK OJSASSHMBILFD (10 SFPARATE PARTS).

in REMOVE THt O10 JOYSTICK ASSEMBLY. SAVE Jf'S MOUNTING HARDWARE. (NO't HOW THI OLD WIRES ARE CONN CED SO yor CAN RECONNECT fHEM iN THE SAM. MANNER TO THE NEW ASSEMBLY WHEN IT {5 JNA STALIED.)

  • ASSIMBLE BASE AND SIDE PLATF WITH O10 HARDWARE .

be INSERT BALL AND SHAFT AND SECURF WITH "f" RING AFTER ASSEMBLING SPRING AND NYLON ACIUATOR BUSHING.

4a INSERE PUSH BUITON ROD AND SPRING INTO BAIL AND SHAFT ASSEMBLY AND CAPTIVATF BY PUSHING ON ACTUATOR PLAIF. (PUSH 10 BOTTOM OF ACTUATOR PLATE.)

  • SNAP ON SWITCH ASSFMBLY. WIRE PER INSTRUCTIONS BELOW.

6b. REWIRF NEW SWITCHES IN THE SAMF MANNER IHAT THE OLD ONtS WERE WIRED.

WIRING INSTRUCTIONS:

le CONNECT THE 6" LONG YELL OW-RED WIRE 10 ONE OF THE "JUMP BUTTON TABS". CONNEC! THF O'HER END OF JHE YELL OW-RED 6" LONG WIRE 10 THE WIRF THAT 1S COMMON TO AL! SWITCHES ON THE CONTROL PANE «

  • CONNECT THE 23" 1 ONG GREEN-BIACK WIRE TO THE O3HER "JUMP BUTTON TAB". INSTALL THE REMAINING ND OF THIS GREEN-Bi ACK 25" LONG WIRE INIO ANY OPEN PIN OF THF CONIROL PANFIL'S 9 POSITION UNIVERSAL CONNECTOR.

Be CONNECT THE 58" LONG GREEN-BI ACK WIRE 1G PIN 15 OF THE EXISTING CABLE OG! CONNFCIOR. RUN THE GIHER END OF THIS GREEN-BLACK 38" I! GNG WIRE TO THE MAIN CABLE HARNESS HALF OF THE CON- TROL PANFI 9 POSITION UNIVERSAL CONNFCTOR. INSTALL THIS €ND OF THF WIR} INTO THE MATING OPEN PIN (SO JT WIL} CONNEC! WITH THE WIRE INSTALLED IN STEP 2 ABOVE = IN IHt OTHER HALF OF THE CONTROL PANE! 'S UNIVERSAL CONNECTOR - WHEN IT IS PUT TOGETHER).

M05 1-00A63-A011

Page 24

10.

11.

12. Install and secure your games Replacement Control Panel.

Secure your games access doors, reconnect it to it's power source, turn it ON, and check to see if your picture appears upside down and reversed.

A. If it is 0.K., run a Self-Test and go on to Step 12 below.

B. If the picture is upside down and reversed, (LEFT is RIGHT and RIGHT is LEFT), go to the MONITOR MODIFICATIONS SECTION where it is explained how to correct this condition.

When through completing a positive Self-Test (everything checks good), yeur game is ready for use.

LIst OF MAJOR PARTS

INCLUDED IN YOUR CONVERSION KIT

UP'N DOWN TO MR. VIKING CONVERSION

FROM

FROGGER CONVERTED TO UP'N DOWN

PART NO.

AA95-00004-0000 ABO2-00002 -0000 A084-91742 -AA93 M051-O0A92-A0 12 M05 1-00A93-A009 M051-00A93-A012 M051-00121-A010 M051-00122-0000 0A92-00300-0000 0A93-00900-00XF 0807-00904-0100 0B07-00904-0200 Q315-05041-0000 0A92-00803-0001 0A92 -00803-0002 0A92-00803-0003 0A92-00803-0004 0A92-00803-0005 0A92-00803-0006 0A92-00803-0007 0A92-00803-0008 0A92-00803-0009 0A92-00803-0010 0A92-00803-0011 0A92-00803-0012 0A92-00803-0013 0A92-00803-0014 OA92-00803-0015 DESCRIPTION

CONTROL SHELF ASSY. CONVERSION CABLE ASSY, INTERFACE BOARD ASSY. LOGIC BOARD LABEL GAME PLAY INSTRUCTION LABEL CONVERSION KIT INSTRUCTION MANUAL SERIAL NUMBER LABEL MANUAL REQUEST POST CARD PARTS CATALOG - MR. VIKING HEADER RIGHT SIDE DECAL LEFT SIDE DECAL CUSTOM I.C. EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM EPROM

Page 25

UP'N DOWN TO MR. VIKING CONVERSION

Disconnect and remove the UP'N DOWN game board.

Replace the EPROMS indicated in the following illustration with those provided in your Conversion Kit,

Reinstall the NEWLY modified game board exactly as it was previously and reconnect it to it's cabling.

Remove the screws from the Header Retaining Bracket and replace the Header.

Remove and disassemble your Control Panel so that you can install the new Control Panel Overlay and additional Push Buttons. (See the following illustration.)

Reassemble your Control Panel and modify it's wiring as follows so that the RED Push Buttons cause Mr. Viking to shoot arrows and the YELLOW Push Buttons will cause him to throw Bombs, Missiles, etc.

CHECK TO SEE THAT YOUR GAMES WIRING CONFORMS TO THE FOLLOWING (MODIFY IT WHERE NEEDED):

A. Insert one end of the 39" long BLACK wire into pin 8 of the 44 position Edge Connector of the Logic P.C. Board. Insert the other end of this 39" long BLACK wire into an open pin of the cabinet cable harnes half of the Control Panel Universal Cable Connector.

B. Insert one end of the 23" long BLACK wire into the mating open pin of the Control Panel cable harness half of the Control Panel Universal Cable Connector.

C. Locate the 14" long BLACK wire. Now twist one end of this wire together with the free end of the above 23" long BLACK wire and solder them both to the TOP TAB of the Fire Button.

D. The other end of the 14" long BLACK wire is to be soldered to the TOP TAB of the Second Fire Button. TS

—E. Take one of the two 4" long YELLOW/BLACK wires and solder one end of this wire to the BOTTOM TAB of the Fire Button. Now solder it's other end to the wire that is common to all switches.

F. Take the remaining 4" long YELLOW/BLACK wire and solder one end of this wire to the BOTTOM TAB of the Second Fire Button. Now solder it's other end to the wire that is common to all switches.

Install the Decals provided with your Conversion Kit OVER those currently on your game. See the Decal Installation Instruction Section of this booklet.

Install the Game Play Instruction Label on the new Main-Display-Glass in the space provided.

Page 26

~ #1 =

MR. VIKING PARTS LOCATIONS

DRAWING PART NOEER_ NOBBER DESCRIPTION 1.C. NUMBER 2 315-5041 CUSTOM IC IC. 125

3316-5749EPROMLC. 86
4 316-5750EPROMI.C. 93
5 316-5873EPROM1.C. 129
6 316-5874EPROM1.C. 130
7 316-5875EPROMrec. 131
8 316-5876EPROMLC. 132
9 316-5755EPROMEC. 133
10 316-5756EPROMIC. 134

316-5757 EPROM IC. 63

12 316-5758EPROMLc. 80
3 316-5759EPROMLC. 64
4 316-5760EPROMLC. 81
15 316-5761EPROMIC. 65
16 316-5762EPROMLc. 82
47 316-5763EPROMLc. 3

@. (i Ounh ou 1086 [fice LOT e ree J Eaicr20 OSes | te192 O- [. zen ice “ye SEE. \co4 “ waz Ices Jobs QQ

Page 27

STEP _A

Remove all push button

switches.

Remove 'E' ring and Actuator from

joystick. Remove joystick. STEP _C

Remove protective

backing from new overlay. Align overlay with top holes & wrap around ends per sketch. INSTRUCTIONS FOR CONTROL SHELF CONVERSION STEP _B Remove Self Stick Covers marked A. (See

Sketch) Remove hole plugs marked B. (See Sketch) Discard parts A & B. With sharp knife cut present overlay to open new switch holes

marked C. Remove sponge tape from underside of shelf & discard. STEP D Install new P.B. switches as indicated per sketch. Reinstall joystick components. Proceed to wire 2 new red P.B. switches. See “Control Shelf Wiring Instructions”. —~ YELLOW

Page 28

10.

11,

12.

13. Remove and replace your games old Main-Display-Glass with the new one provided in your Conversion Kit.

Install and secure your games modified Control Panel.

Secure your games access doors, reconnect it to it's power source, turn it ON, and check to see if your picture appears upside down and reversed.

A. If it is 0.K., run a Self-Test and go on to Step 13 below.

B. If the picture is upside down and reversed, (LEFT is RIGHT and RIGHT is LEFT), go to the MONITOR MODIFICATIONS SECTION where it is explained how to correct this condition.

When through completing a positive Self-Test (everything checks good), your game is ready for use.

Page 29

= 24 -

LIST OF MAJOR PARTS

INCLUDED IN YOUR CONVERSION KIT

UP'N DOWN TO MR. VIKING CONVERSTON

PART NO. DESCRIPTION

AA92-00006-0000 GAME PLAY INSTRUCTION CARD WITH TAPE AA97-00004-0000 CONTROL CABLE AB02-00002-0000 CONVERSION CABLE ASSY. M051-00A92-A012 LOGIC BOARD LABEL M051-00A93-A012 CONVERSION KIT INSTRUCTION MANUAL M051-00121-A010 SERIAL NUMBER LABEL M05 1-00122-0000 MANUAL REQUEST POST CARD 0A92-00900-00XF HEADER 0B07-00900-00 XF MAIN-DISPLAY-GLASS 0B07-00901-0000 CONTROL SHELF OVERLAY 0B07-00905-0100 RIGHT SIDE DECAL 0B07-00905-0200 LEFT SIDE DECAL 0017-00032 -0093 PUSH BUTTON SWITCH 0017-00103-0054 5/8 - 11 PAL NUT 0151-00804-0002 YELLOW PUSH BUTTON ASSY. 0151-00804-0008 RED PUSH BUTTON ASSY, 0A92-00300-0000 PARTS CATALOG - MR. VIKING Q315-05041-0000 CUSTOM I.C. 0A92-00803-0001 EPROM 0A92-00803-0002 EPROM 0A92-00803-0003 EPROM 0A92-00803-0004 EPROM 0A92-00803-0005 EPROM 0A92-00803-0006 EPROM 0A92-00803-0007 EPROM 0A92-00803-0008 EPROM OA92-00803-0009 EPROM 0A92-00803-0010 EPROM 0A92-00803-0011 EPROM OA92-00803-0012 EPROM 0A92-00803-0013 EPROM 0A92-00803-0014 EPROM 0A92-00803-0015 EPROM

Page 30

MONITOR MODIFICATIONS SECTION

If the picture in your modified game is upside down and reversed (LEFT is RIGHT and RIGHT is LEFT); depending on the monitor contained in your game; this condition can be fixed in one of the following ways.

TURN THE POWER To YOUR GAME OFF!!

MONITOR: ELECTROHOME - YOKE WIRES SOLDERED IN PLACE AT BOTH ENDS. REFER TO DRAWING #1

By the picture tube, cut the 4 yoke wires (RED, WHITE, GRAY, and BROWN). BE SURE to leave enough room to strip them and splice them back together as shown in Drawing #1.

MONITOR: ELECTROHOME - YOKE WIRES PLUGGED INTO THE MONITOR'S P.C. BOARD. REFER TO DRAWING #2

You will see the yoke wires (BROWN, WHITE, GRAY, and RED) plugged into the monitor's P.C. Board at it's back right-hand corner, just below the flyback. See Drawing #2 Figure A.

Unplug them and reconnect them as shown in Drawing #2 Figure B.

MONITOR: WELLS GARDNER - YOKE WIRES PLUGGED DIRECTLY INTO THE YOKE. REFER TO DRAWING #3

You will see the yoke wires (YELLOW, BLUE, RED, and GREEN) plugged into the monitor's yoke. Unplug them and switch the pairs indicated in Drawing #3.

UPON COMPLETION OF MODIFICATIONS:

Return to the procedure you left to come to this section, at the point you left it, and complete that procedure.

Page 31
  • 25a -

PICTURE s— TUBE

WIRE NUT (4)

ELECTROHOME (FIXED)

DRAWING 1

Page 32
  • 25b -

FIGURE A

MONITOR PC. i

$ FLYBACK

eke goo

® (BACK RIGHT CORNER) tit V.CENT.

ELECTROHOME

(FIXED)

FIGURE B

MONITOR P.C, ¥

fo}

ooo Vdekr @| (BACK RIGHT CORNER)

(FIXED)

DRAWING 2

Page 33
  • 25¢ -

—— 2 PICTURE

TUBE

itl a Berta Hen

WELLS GARDNER (FIXED)

DRAWING 3

Page 34

DECAL INSTALLATION INSTRUCTIONS

READ THE FOLLOWING INSTRUCTIONS THROUGH COMPLETELY AT LEAST ONCE BEFORE ATTEMPTING TO INSTALL THE DECAL(S) THEY CONCERN! !

THE DECAL(S) ARE COMPOSED OF THREE (3) PARTS: 1)A HEAVY WAXED BACKING SHEET WHICH COVERS THE STICKY SIDE OF THE DECAL, 2)” THE DECAL ITSELF, AND 3)A THIN MASKING SHEET WHICH IS ON THE FRONT SIDE OF THE DECAL TO PROTECT IT AND TO AID IN ITS INSTALLATION.

4 ee ee ee EH HH © TO INSTALL THE DECAL(S), PROCEED AS FOLLOWS: # # # HH RR RRR

1,

2. BE SURE THE AREA WHERE YOU ARE GOING TO APPLY THE DECAL IS CLEAN AND FREE OF ALL DIRT, GREASE, AND GRIME.

USING ANY SPRAY-ON GLASS CLEANER, THOROUGHLY WET DOWN THE AREA WHERE YOU INTEND TO PUT THE DECAL.

REMOVE THE HEAVY WAXED BACKING SHEET FROM THE DECAL BY POSITIONING IT FACE UP ON A FLAT SURFACE; GOING TO ANY CORNER; AND BENDING THIS CORNER UP SLIGHTLY TO SEPARATE THE DECAL AND THIN MASKING SHEET FROM THE HEAVY WAXED BACKING SHEET.

SLOWLY AND CAREFULLY PEEL THE HEAVY WAXED BACKING SHEET AWAY FROM THE DECAL AND MASKING SHEET. .

PLACE THE DECAL ON THE GAME CABINET OVER THE WET GLASS CLEANER YOU JUST APPLIED. (THIS WILL ALLOW A SMALL AMOUNT OF FINAL POSITIONING TO BE DONE AFTER THE DECAL IS APPLIED TO THE GAME CABINET.)

SMOOTH THE DECAL.

ALLOW THE DECAL TO BECOME FIRMLY AFFIXED TO THE GAME BEFORE PROCEEDING TO THE NEXT STEP.

REMOVE THE THIN MASKING SHEET FROM THE DECAL AT THIS TIME BY MOISTENING IT WITH A WET CLOTH OR SPONGE. RUB WITH FINGER TIPS (NOT NAILS) FROM A CORNER EDGE TOWARD ITS CEN- TER. PEEL THE THIN MASKING SHEET BACK OVER ITSELF TO REMOVE IT. DO NOT PULL IT STRAIGHT AWAY FROM THE CABINET.

Page 35

v © 1984 BALLY MIDWAY MFG. CO ALL RIGHTS RESERVED

CESIGNATION L

DESCRIPTION

DUAL 22FiN EDGE CONN MR VIKING/ FROGGER INTERFACE

MR VIKING yi 8/7/84 CROSS REFERENCE LIST

DESCRIPTION. Qty DESIGNATION PART NO |

DUAL 22 PIN | Jl 0017-00021-0395 EDGE CONN MR VIKING /FROGGER | P.C.B A080-91742- AA93 INTERFACE

| Phutig MIDWAY mes co Tt | Ree REVISIONS t MR. VIKING / FROGGER INTERFACE ° | ASSEMBLY DRWG ane ' 9080— 91742—AA93 MOS! OO AQ 3 AOIO

Page 36

MR. VIKING Ji J2 FROGGER

GND A> — p> 7

GND GND GND +5 oO

+5 +5 +5

COIN METER

+12 natunougr®rer t i | nu. | i I i} if I

2 FIRE

| FIRE e

2 BOMB K

i) L | (CABLE) | (CABLE) | (CABLE)

uA

1 BOMB | A

I 2 DOWN _ >— | 1 DOWN "4 >

2 UP 1 UP

2 RIGHT

1 RIGHT 13

2 LEFT

{LEFT 1 START Lt A 9 2F=ortr?> OOW 4H

a \

COIN 1 2 START AMAA

A

TEST 17 \ (CABLE)

SERVICE SPEAKER (-) SPEAKER (+) GRN RED SYNC AAKARAA

BLU GND (SYNC) 2: es, st Pe ' ! ! I I ! ! ! \ I ! ' I I ! i I I I I

A

A MEAT TREAT PROJECT ENG. J SZERSZEN Buby / MIDWAY MFG. co. NO REQ'D {PER FRANKLIN PRK TLL

MR. VIKNIG/ FROGGER INTERFACE PC PART NO SCHEMATIC DWG MOS! — OOA93-A0I!

AO8O - 91742 - AAQZ

Page 37

© 1984 BALLY MIDWAY MFG.. CO. ALL RIGHTS RESERVED R.VIKING/ZAX XON, INTERFACE P.C.

PAT. PENDING

:

< <

:

<

DESIGNATION LIST CROSS REFERENCE _LIST

DESIGNATION DESCRIPTION DESCRIPTION QTY DESIGNATION PART NO

JlDUAL 22PINDUAL 22 PINIJl0017-00021-0395

EDGE CONN EDGE CONN.

PCBMR. VIKING/ ZAXXONMR. VIKING /ZAXXON|P.C.B.A080-91743- AA94

INTERFACE INTERFACE

silty iMIDWA Y mre. co. wh a FRANALIN PARK. Ik ott: - —pan: _— _ MR. VIKING /ZAXXON INTERFACE ASSEMBLY DRWG AO080— 91743 — AA94 PROJECT ENG’ J.SZERSZEN

DIM. TOLERANCES “ih os MR. VIKING UNLESS OTHE WSL SPEC Sey nie : CONCENTRICTY TIP U02 :

CONCERTee18/7/84A

OECIMAi o¢s HOLE Dia + 992-- 000 ANGLE 2 12° DO NOT SCALE DWG 1-0 0A94 -A010

BRUNING: 4¢-sa7

Page 38

bEYY- Sb4I16 - O80 OMG SILVAN3HOS — Od BOVSNSLNI NOXXVZ/9ININIA YW i10V-b6¥OO — 1SOW

ON Luve aul ty A

Yad | au ON and a wand “0993 AVMGIN | 4p oN —

‘SNOISIASY.

YW No o3sn Nae

BOIAWSS > @

483i AAAAAAAAAAA A AAAAAAAAA

AMOS NM awog i awog 2 Suid Aaa

aaa? Ag+ +83. 3WNIOD 2 ¥313W NICO I

! i i i i 1 st I ! ' I

s+ ano ano ano ano ONINIA UA,

Page 39
UF he tee eeerepatsts?:
SEE tee tantePsa?a
aesipatracha fener
ter ancteyecs37?Sian nau 82
Cer sartewhessssSon:

at ‘ese =o, oy Se tee wt? 3508 bin spst ri *

+ Base 8 > si [io on WR VIKING Pour ewe. SZERSZEN fro ewe 1 PER Baby | MIDWAY MFG..CO. == S7aea WA. VIKING LOGIC PC ‘ASSEMOLY OG 080-91750-AR92 MoS! ~o0A92 - A010

Page 40

see

egee-
Fl23Fl

| 3

2=Iraieh
26,29,20420,

a

/|]
i||
||\
||||t
leiesisobers| terse) reise | cise1138
27642784ares|2764|ares|2764BoE SH rcosssse- a
EP R- 5873,EpR- 867seon-sers | epr-seve =| cpr-sess =| ePR-seea = |_ADII 25)

| ft Be

||||| law ez
‘5b-6061i|||WR 27]
||i|LL
|||© YB VERSION. TO om}
||+8
||||a vERYiow
|||WITH RESISTOR

a i

Eos*rT7L cut a vension

] |

00-07 ADO- ADIs WO. WR TORE

ys as

WR 2/9 eon 9/9

|DWROR 4/9fast ye
4/9 DMAENDaaaifTU ogNOTE GouMPER PADoe

SHORTED = NEG SYNC

12] reree120 6OPEN - POS SYNC

6 acank

reve soa nze 2 190 Mo-wT XTAL ew ERE vo-v7 Weise azo Cowart. r torae m8 cise ie to Pye ance | = {

| esosrIioma_._TUINE 479
|Lo+H=Me 7/9
108aayT

| : a

era UIP.— =4 E D> 11 100 rec r se.___Bavck v9

L slo us 2/9 FXHMB a SRLCK, 7

1631

REVISIONS

@ily | MIDWAY MFG.CO. FRANKLINPR LL USED ON MR. VIKING

SCHEMATIC DWG. MR. VIKING LOGIC P.C. A080 -9!1750-AA92 PAGE | OFS eat TRE

seve |_| DIM TOLERANCES PART NO

MOS! = 00A92-A0!i

Page 41

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 42

SRLCK U3 2/9mlCG-icG7

f

1/9:

2/9 cu:

‘

A

3]

4! STOM(IGPIN) X3

[iereg |

10 SRLDS. terse Tu sruce

sis fiz smu. sos [ia ae

6 FIX

1e187

sos

Feqw tilsy 2/9 ecg ‘a F304 Shon v ay 136 ay

3668.31,92a,sooFign 3],“
|361 18] aygg 2ly361 2F200 Olay

| 5

|see],aSS|.est30H 6]o,N U
|seesitlry seas TOF14] 5x63 4 seuss13] 45
3064 7] 55 "35 50/6sl.can"i
3065 14155318

so 6a F 5025

3068 8],,4g?4l,pees 7
369713},,salis],6

Hb NU ple ve

SCROLL LATCH 2/9 sso V9 pf IXST (Qe) ssi

ss3

3/9 »FLP 1/9 SM i. seg $B. $82

Fe FBI Fe2 7/9

PROJECT ENG SZERSZEN [_comorseanowe Nor MEAT TREAT DIM TOLERANCES

mourers 4007 000 5/21/84 SCHEMATIC DRAWING MR.VIKING LOGIC PC. A080 -91750 - AA92 USED ON MR. VIKING

PAGE 30F9 REVISIONS

@cly | MIDWAY MFG.CO. FRANKLIN PK

PART NO.

MOSsI

  • 00A92- AOI!
Page 43

ae

3|i1

zae-s5 | neg-55 | 2i4e-58 2149-85, |

cixxay | cin eay(ikx4)Cikxa) |
aieekeRATZh,(ciseieisoierice |

a oe on

L. STEWS _ i TEND

a Ls04

|nosfi
|usasxeens|
-=tece

122 1. od

“9?lu_x0enoemed

pera Bf Ao a?

tea]ice ®toedre

ws

ol2 34s 678 2] yal

‘cos.

DIM. TOLERANCES UNLESS SPECIFIED. pRovect ENG: J. SZERSZEN

DO NOT SCALE WG

cane 8/2 Opn! ony o6n ss oem. HALF

8/9

PLY fe

s/o

REVISIONS

USED ON MR. VIKING

PART NO.

mosi SCHEMATIC DWG. MR. VIKING A080 - 91750-AA92 PAGE 4 0F9 @aly | MIDWAY MFG. CO. FRANKLIN PK ILL

  • 00A92-A0Il
Page 44

74.8187

49 48 >

4/2 PLY

PLY

EDA®—EDA4, EDAT

ess 20 as — Spas, So -8¢00 4/9 Ce 2 Cong - 08N4

TaLseee dan > 2-1¢27 fe =" couog 7 Uwe

aK £ oe 6

= 2 26/9, 7/9 is 3 z 4 oBHNB 1/9

= OPLY 7/9

ve HPs 6 4/oqg— oT eo 1/9 etl |_| > SMB

ADDED R32 & R33 REv.O, [RLW REVISIONS PROJECT ENG: J: SZERZEN luseo on MR. VIKING Baby | MIDWAY MFG co

Tin TOLERANCES | schemaric prawine eilan MR. VIKING LOGIC P.C. MOS! - OOAS2-AOl!

Page 45

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 46

usivaxe 2-168 qsiwsxs 3c icisr Lesion? tte Tera SITS XK? 2-152

“ =*. 1-8 ~ ” tt 4 ng a A ra co a :

vo poEubiTes2 J

on waist

‘306-382 SRG ”

aa Ds~07 t us

‘ 6 4 FLT

ce x0

Fad

SCROLL LATOR. vs co

a0 vs te

nore PIN #S FOR IClO8 REFER TO Pci SILKSCREEN WHICH IS FOR AN CHIP.

REVISIONS

USED ON MR. VIKING @eby | MIDWAY MFG.CO. FRANKLIN PK ILL PROJECT ENG: J. SZERSZEN

DIM TOLERANCES PART NO.

MO5I — OOA92-AOll SCHEMATIC DWG. MR. VIKING LOGIC RC. A080 -91750 - AAS2

PAGE 7 OF9

Page 47

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 48

s/s so 1 so2 so 3. so4

SDS

soe

S07 ql RESET

‘Busre

INT

ba

os

de

or T4L8138

tr R,6,8 271 cok apt OTHER 222

EPR-5763,

2763

Tacc € 300n8 n [sans Tacc € 250n8 sop 10 ce fan [so 3] oa ca

soe a, C4 iu Ot TANT S07 Let ka +, cux | ne $10 0nm cod Film 2K 2 a LA4460 WITH HEATSINK

T4LS107

REVISIONS

@aly | MIDWAY MFG.CO.

FRANKLIN PK ILL PROJECT ENG J. SZERSZEN USED ON MR.VIKING

DIM TOLERANCES PART NO

MO5I — OOA92-A0I! SCHEMATIC DRAWING

MR.VIKING LOGIC P.c.

A080-91750-AA92 PAGE 9 OF9