CATHODE RAY TOMES

Wave Runner GP

Wave Runner GP (CRI / Sega, 2001) · Manual · 182 pages · 274 sections · original scan

Page 1

Ist PRINTING NOV 01 S

oY:

™

SEGA ENTERPRISES, INC. USA

MANUAL NO. 999-1375

Page 2

VISIT OUR WEBSITE!

| Sherlock Preferences | Larger Smaller i

+ Dari's Office «Game Manuals *“Seerenh oWhoet's New

556 4Boeag have visited this page since 3/16/01

ones one in If you have any questions or comments

Service Department 4

Preiep nya about this site please E-Mail to Darl Davidson@seu sega com

tax 415.701 0604

THOR WER BUTE POwENEO OY

WebSTAR 4-3

You will need the ot items to view this = in its entirety

AllPlatforms Windows Macintosh

Page 3

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: To maintain the safety:

To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary.

Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. are used. Be sure to understand the contents of the displays before reading the text.

Indicates that mishandling the Indicates that mishandling the product product by disregarding this by disregarding this caution will cause

warning will cause a potentially a slight hazardous situation which can
WARNING! hazardous situation which can CAUTION! result in personal injury and or material result in death or serious injury. damage.

For the sage usage of the product, the following pictographs are used:

Indicates “HANDLE WITH CARE.” In order to protect the human body an equipment, this display is attached to places where the Owner’s Manual and or Service Manual should be referred to.

© Perform work in accordance with the instructions herein stated. Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions can cause accidents. In the case where only those who have technical expertise should perform the work to avoid hazardous situation, the instructions herein state that the serviceman should perform such work.

© Be sure to turn off power before working on the machine. To prevent electric shock, be sure to turn off power before starting the work in which the worker touches the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual herein always states to that effect.

© Be sure to ground the Earth Terminal (this, however, is not required in the case where a power cord with earth is used). This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Terminal to the “accurately grounded indoor earth terminal” by using an earth wire. Unless the product is grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment.

© Ensure that the Power Supply used is equipped with an Earth Leakage Breaker. This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.

© Be sure to use fuses which meet the specified rating. (only for the machines which use fuses). Using fuses exceeding the specified rating can cause a fire and electric shock.

Page 4

O Specification changes (removal of equipment, conversion and addition) not designated by SEGA are not allowed. The parts of the product include warning labels for safety, covers for personal protection, etc. It is very hazardous to operate the product by removing parts and or modifying the circuits. Should doors, lids and protective parts be damaged or lost, refrain from operating the product, and contact where the product was purchased from or the office herein stated. SEGA shall not be held responsible for any accidents, compensation for damage to a third party, resulting from the specifications not designated by SEGA. ©. Ensure that the product meets the requirements of appropriate Electrical Specifications. Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on which Electrical Specifications are described. Ensure that the product is compatible with the power supply voltage and frequency requirements of the location. Using any Electrical Specifications different from the designated Specifications can cause a fire and electric shock. © _ Install and operate the product in places where appropriate lighting is available, allowing warning labels to be clearly read. To ensure safety for the customers, labels and printed instructions describing potentially hazardous situation are applied to places where accidents can be caused. Ensure that where the product is operated has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please place an order with where the product was purchased from or the office herein stated. © When handling the Monitor, be very careful. (Applies only to the product w/monitor.) Some of the monitor (TV) parts are subject to high tension voltage. Even after running off power, some portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be performed only be those technical personnel who have knowledge of electricity and technical expertise. © Besure to adjust the monitor (projector) properly. (Applies only to the product w/monitor.) Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the customers. © _ When transporting or reselling this product, be sure to attach this manual to the product. In the case where commercially available monitors and printers are used in this product, only the contents relating to this product are explained herein. Some commercially available equipment has functions and reactions not stated in this manual. Read this manual together with the specific Instruction Manual of such equipment.

° Descriptions herein contained may be subject to improvement changes without notice. ¢ The contents described herein are fully prepared with due care. However, should any question arise or errors be found, please contact SEGA.

INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.

Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on power, check the following points to ensure that the product has been transported in a satisfactory status. Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet? Are Casters and Adjusters, damaged? Do the power supply voltage and frequency requirements meet with those of the location? Are all wiring connectors correctly and securely connected? Unless connected in the correct direction, connector connections can not be made accurately. Do not insert connectors forcibly. Do power cords have cuts and dents? Do the fuses used meet specified rating? Is the Circuit Protector in an energized status? Are all accessories available? Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?

Page 5

TABLE OF CONTENTS

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS. INTRODUCTION OF THE OWNER'S MANUAL . HANDLING PRECAUTIONS .... see PRECAUTIONS CONCERNING INSTALLATION LOCATION OPERATION .... NAME OF PARTS ACCESSORIES ASSEMBLING AND INSTALLATION PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE CONTENTS OF GAME ... EXPLANATION OF TEST AND DATA DISPLAY. 9-1 SWITCH UNIT AND COIN METER .. 9-2 SYSTEM TEST MODE 9-3 GAME TEST MODE

  • AIR DRIVE ... 10 - 1 OVERVIEW OF AIR DRIVE SYSTEM. 10 - 2 DEWATERING FROM THE AIR FILTER. 10 -3 DEWATERING FROM THE AIR TANK . 10-4 REGULATOR... 10-5 AIR CLEANER .... . MAINTENANCE OF MECHANISM UNIT 11 - 1 REMOVE THE LID & THE BELLOWS BEFORE SARTING MAINTENANCE WORK... 11 - 2 GREASING AND RETIGHTENING THE BOLTS 11 -3 ADJUSTMENT AND REPLACEMENT OF PITCH VOLUME 11 -4 REMOVE THE INCLINATION SENSOR
  • HANDLE MECHANISM .. 12 - 1 ADJUSTING AND REPLACING THE THROTTLE V.! 12 -2 ADJUSTING OR REPLACING THE HANDLE V.R. 12-3 GREASING.
  • COIN SELECTOR,
  • PROJECTOR. 14-1 CLEANING THE SCREEN 14-2 ADJUSTMENT OF TOSHIBA PROJECTOR,
  • REPLACEMENT OF FLUORESCENT LAMP.
  • PERIODIC INSPECTION TABLE
  • TROUBLESHOOTING ...... 17 - 1 TROUBLESHOOTING 17-2 ERROR MESSAGE ..
  • GAME BOARD 18 - | REMOVING THE GAME BOARD. 18 - 2 COMPOSITION OF GAME BOARD.
  • DESIGN RELATED PARTS,
  • COMMUNICATION PLAY .. 20-1 INSTALLATION PRECAUTIONS 20 - 2 CONNECTING THE COMMUNICATION CABLE 20-3 SETTING FOR COMMUNICATION PLAY 20-4 CAUTIONS TO BE HEEDED DURING COMMUNICATION PLAY
  • PARTS LIST .........0.
  • WIRE COLOR CODE TABLE
  • WIRING DIAGRAM . 24, PIPING DIAGRAM OMI DARWHN
Page 6

SPECIFICATIONS

Installation space : 56in [1,435 mm] (W) X 123in[3120 mm] (D) Height : 87.4 in. [2,220 mm] Weight 1 1,194 Ibs. [543 kg.] Power, maximum current : 1,250 W 11.5 A (AC 120V 60 Hz AREA) 1,150 W 6.4 A (AC 220V 50 Hz AREA) 1,240 W 7.0 A (AC 220V 60 Hz AREA) 1,150 W 5.8 A (AC 230V 50 Hz AREA) 1,140 W 5.6 A (AC 240V 50 Hz AREA) For TAIWAN Power, current 11,250 W 12.5 A(MAX.) 750 W 7.0 A(MIN.) MONITOR : 50 TYPE PROJECTION DISPLAY

INTRODUCTION OF THE OWNER'S MANUAL

This Owner's Manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the product, WAVERUNNER GP. This manual is intended for the owners, personnel and managers in charge of operation of the product. Operate the product after carefully reading and sufficiently understanding the instructions. If the product fails to function satisfactorily, nontechnical personnel should under no circumstances touch the internal system. Should any malfunctioning occur, turn the power off and unplug the Power Cord (AC Cable), and contact where the product was purchased from.

Use of this product is unlikely to cause physical injuries or damages to property. However, where special attention is required this is indicated by a thick line, the word "IMPORTANT" and its sign in this manual.

Indicates that mishandling the product by disregarding this display can cause the product's intrinsic performance not to be obtained, resulting in malfunctioning.

IMPORTANT!

SEGA ENTERPRISES, INC. (U.S.A.)/CUSTOMER SERVICE 45133 Industrial Drive, Fremont, California 94538, U.S.A. Phone: (415) 701-6580 Facsimile: (415) 701-6594

Page 7

DEFINITION OF LOCATION'S MAINTENANCE MAN AND SERVICEMAN

WARNING! Non-technical personnel who do not have technical knowledge and expertise should refrain from performing such work that this manual requires the location's maintenance man or a serviceman to carry out, or work which is not explained in this manual. Failing to comply with this instruction can cause a severe accident such as electric shock.

Ensure that parts replacement, servicing & inspections, and troubleshooting are performed by the location's maintenance man or the serviceman. It is instructed herein that particularly hazardous work should be performed by the serviceman who has technical expertise and knowledge.

The location's maintenance man and serviceman are herein defined as follows:

"Location's Maintenance Man" : Those who have experience in the maintenance of amusement equipment and vending machines, etc., and also participate in the servicing and control of the equipment through such routine work as equipment assembly and installation, servicing and inspections, replacement of units and consumables, etc. within the Amusement Facilities and or locations under the management of the Owner and Owner's Operators of the product.

Activities of Location's Maintenance Man : Assembly & installation, servicing & inspections, and replacement of units & consumables as regards amusement equipment, vending machines, etc.

Serviceman : Those who participate in the designing, manufacturing, inspections and maintenance service of the equipment at an amusement equipment manufacturer. Those who have technical expertise equivalent to that of technical high school graduates as regards electricity, electronics and or mechanical engineering, and daily take part in the servicing & control and repair of amusement equipment.

Serviceman's Activities : Assembly & installation and repair & adjustments of electrical, electronic and mechanical parts of amusement equipment and vending machines.

Page 8

General Precautions

Follow Instructions: All operating and use instructions should be followed.

Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards. Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer. Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product to overturn. Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Power Sources: This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

  • If the power cord or plug is damaged;
  • If liquid has been spilled, or objects have fallen into the product;
  • If the product has been exposed to rain or water;
  • If the product does not operate normally when following the operating instructions. Adjust only those controls that are explained in the operating instructions. An improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation;
  • If the product has been dropped or damaged in any way;
  • When the product exhibits a distinct change in performance; this indicates a need for service. Replacement Parts: When replacement parts are required, be sure the service technician has used replacements parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Page 9

Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’s recommendations. Do not dispose in an open flame condition, since the battery may explode. Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such as benzine, thinner, etc. Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors in the places mentioned below: + Places subject to rain/water leakage, or condensation due to humidity; + In close proximity to a potential wet area; + Locations receiving direct sunlight; + Places close to heating units or hot air; +In the vicinity of highly inflammable/volatile chemicals or hazardous matter;

  • On sloped surfaces; + In the vicinity of emergency response facilities such as fire exits and fire extinguishers; + Places subject to any type of violent impact; + Dusty places.

INSTALLATION PRECAUTIONS + Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.

+ Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG rated min. 120 VAC, 7A. + Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H). + For the operation of this machine, secure a minimum area of 64” (W) by 97°(D).

REGULATORY APPROVALS This game has been tested and found to comply with the Federal Communications Commission Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.

LISTED

5K92

AMUSEMENT MACHINE

Page 10
  • HANDLING PRECAUTIONS

A

WARNING! When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine.

Before performing work, be sure to turn power off. Performing the work without turning power off can cause an electric shock or short circuit. In the case work should be performed in the status of power on, this manual always states to that effect. To avoid electric shock or short circuit, do not plug in or unplug quickly. To avoid electric shock, do not plug in or unplug with a wet hand. Do not expose Power Cords and Earth Wires on the surface, (floor, passage, etc.). If exposed, the Power Cords and Earth Wires are susceptible to damage. Damaged cords and wires can cause electric shock or short circuit.

To avoid causing a fire or electric shock, do not put things on or damage

Power Cords. When or after installing the product, do not unnecessarily pull the power cord. f damaged, the power cord can cause a fire or electric shock. n case the power cord is damaged, ask for replacement through where the product was purchased from or the office herein stated. Using the cord as is damaged can cause fire, electric shock or leakage. Be sure to perform grounding appropriately. Inappropriate grounding can cause an electric shock. Be sure to use fuses meeting specified rating. Using fuses exceeding the specified rating can cause a fire or electric shock. Completely make connector connections for IC BD and others. Insufficient insertion can cause an electric shock. Specification changes, removal of equipment, conversion and/or addition, not designated by SEGA are not permitted.

Failure to observe this may cause a fire or an electric shock. Non-compliance with this instruction can have a bad influence upon physical conditions of the

players or the lookers-on, or result in injury during play. SEGA shall not be held responsible for damage, compensation for damage to a third party, caused by specification changes not designated by SEGA. Be sure to perform periodic maintenance inspections herein stated.

Page 11

@ For the IC board circuit inspections, only the logic tester is allowed. The use of a multiple-purpose tester is not permitted, so be careful in this regard. @ The Projector is employed for this machine. The Projector's screen is susceptible to damage, therefore, be very careful when cleaning the screen. For details, refer to PROJECTOR.

IMPORTANT

Some parts are the ones designed and manufactured not specifically for this game machine. The manufacturers may discontinue, or change the specifications of, such general-purpose parts. If this is the case, Sega cannot repair or replace a failed game machine whether or not a warranty period has expired.

Page 12
  • PRECAUTIONS CONCERNING INSTALLATION

LOCATION

avoid installing in places mentioned below so as not to cause a fire, electric shock, M\ This product is an indoor game machine. Do not install it outside. Even indoors,

WARNING! injury and or malfunctioning. @ Places subject to rain or water leakage, or places subject to high humidity in the proximity of an indoor swimming pool and or shower, etc. @ Places subject to direct sunlight, or places subject to high temperatures in the proximity of heating units, etc. Places filled with inflammable gas or vicinity of highly inflammable/volatile chemicals or hazardous matter. Dusty places. Sloped surfaces. Places subject to any type of violent impact. Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. The operating (ambient) temperature range is from 5° to 30°.

LIMITATIONS OF USAGE REQUIREMENTS

Be sure to check the Electrical Specifications. Ensure that this product is compatible with the location's power supply,

WARNING! voltage and frequency requirements. A plate describing Electrical Specifications is attached to the product.

Non-compliance with the Electrical Specifications can cause a fire and

electric shock. This product requires the Breaker and Earth Mechanisms as part of the

location facilities. Using them in a manner not independent can cause a fire

and electric shock. Ensure that the indoor wiring for the power supply is rated at 15A or higher (AC single phase 100 ~ 120V area), and 8A or higher (AC 220 ~ 240V area).

electric shock. Be sure to independently use the power supply equipped with the Earth Leakage Breaker. Using a power supply without the Earth Leakage Breaker can cause an outbreak of fire when earth leakage occurs. Putting many loads on one electrical outlet can cause generation of heat and a fire resulting from overload. When using an extension cord, ensure that the cord is rated at 15A or higher (AC 100 ~ 120V area) and 8A or higher (AC 220 ~ 240V area). Using a cord rated lower than the specified rating can cause a fire and electric shock.

Page 13

OPERATION AREA

A

WARNING! @ For the operation of this machine, secure a minimum area of 1.6m (W) X 3.1m (D). In order to prevent injury resulting from the falling down accident during game play, be sure to secure the minimum area for operation. Be sure to provide sufficient space so as to allow this product's ventilation fan

to function efficiently. To avoid machine malfunctioning and a fire, do not

place any obstacles near the ventilation opening. SEGA shall not be held responsible for damage, compensation for damage to a third party, resulting from the failure to observe this instruction.

on's building, the minimum necessary re 1.45m(W) and 1.68m(H).

  • Electric current consumption s+ Y ML < k MAX. 11.5 A (AC 120V 60 Hz) ge) MAX. 6.4 A (AC 220V_ 50 Hz) MAX. 7.0 A (AC 220V 60 Hz) MAX. 5.8 A (AC 230V_ 50 Hz) MAX. 5.6 A (AC 240V_ 50 Hz) mus Es MAX. 12.5 A (For TAIWAN) or { id

3.55m,

140 inches

1.6m \< >| 63 inches

FIG. 2

Page 14
  • OPERATION

PRECAUTIONS TO BE HEEDED BEFORE STARTING THE OPERATION

WARNING! To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.

In order to avoid accidents, check the following before starting the operation: @ To ensure maximum safety for the players and the customers, ensure that where the product is operated has sufficient lighting to allow any warnings to be read. Operation under insufficient lighting can cause bodily contact with each other, hitting accident, and or trouble between customers. Be sure to perform appropriate adjustment of the monitor (projector). For operation of this machine, do not leave monitor's flickering or deviation as is. Failure to observe this can have a bad influence upon the players' or the customers' physical conditions. It is suggested to ensure a space allowing the players who feel sick while playing the game to take a rest.

Check if all of the adjusters are in contact with the

surface. If they are not, the Cabinet can move and cause an accident. Check to see if the bottom bellows are damaged or omitted. Bellows are important hazard-prevention parts. Irregular bellows can cause injury.

Check bellows.

Ensure that all of the Adjusters are in contact with the floor.

Safety Sensor Before commencing operation, execute test run to check if the Safety Sensor and the Motion Stop Switch are satisfactorily functioning to stop the machine movements during game. The Safety Sensor and the Motion Stop Switch are

important hazard-prevention parts. Irregular important parts can cause injury.

Check for the Safety Sensor's Motion Stop Switch) function to stop movements.

Page 15

Do not put any heavy item on this product. Placing any heavy item on the product can cause a falling down accident or parts damage.

WARNING! Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step. To avoid electric shock, check to see if door & cover parts are damaged or omitted. To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product. Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.

To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can

CAUTION! cause making bodily contact with each other, hitting accidents, and or trouble between customers.

S Be sure to periodically dewater the Air Drive and dispose of the drain water. Excessively gathered water can cause the Air Drive Mechanism to malfunction

IMPORTANT! and get out of order.

| YAMAHA \

FILTER, DRAIN TUBE \WATER TANK

Page 16

PRECAUTIONS TO BE HEEDED DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)

To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.

AY To avoid injury and accidents, those who fall under the following categories

are not allowed to play the game.

WARNING! Those who need assistance such as the use of an apparatus when walking. Those who have high blood pressure or a heart problem. Those who have experienced muscle convulsion or loss of consciousness when playing video game, etc. Those who have a trouble in the neck and or spinal cord. Intoxicated persons. Pregnant women or those who are in the likelihood of pregnancy. Persons susceptible to motion sickness. Persons whose act runs counter to the product's warning displays.

A player who has never been adversely affected by light stimulus might

experience dizziness or headache depending on his physical condition when playing the game. Especially, small children can be subject to those conditions. Caution guardians of small children to keep watch on their children during play. Instruct those who feel sick during play to have a medical examination. To avoid electric shock and short circuit, do not allow customers to put hands

and fingers or extraneous matter in the openings of the product or small

openings in or around the doors. To avoid falling down and injury resulting from falling down, immediately stop the customer's leaning against or climbing on the product, etc. To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason.

The player whose feet can not be placed on the base could fall down and cause injury. To avoid injury, instruct persons of short stature to refrain from playing the game.

Page 17

@ To avoid injury and parts damage, instruct players that only

WARNING! up to two persons are allowed to

ride.

To avoid injury resulting from falling down, and electric shock due to spilled drinks, instruct the player not to place heavy items or drinks on the product.

Do not place drinks

Instruct the player to take a firm grip of the handle Bars during play. This machine reacts as per the contents of the game. To avoid injury, instruct the players to refrain from single-handed taking grip of the handle Bar (which is very likely to cause potentially hazardous situation, should he attempt to do so).

To avoid injury and trouble resulting from coming into contact with each other, instruct persons other than the players to keep away from the mechanism base. The Safety Sensor functions to stop only the machine movement from the Compressor. The ride can be moved by the player.

Page 18

A\ @ Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage or falling down, resulting in injury due to

CAUTION! fragments and falling down. When riding in tandem, firmly hold on to the front player. To avoid injury, do not stand driving the ride.
Page 19
  • NAME OF PARTS BILLBOARD

COMPRESSOR BOX _, FRONT CABINET PTV 50 TYPE PROJECTOR

FIG.4a

COIN | ICHUTE

IDOOR CASHBOX DOOR REAR CABINET

ASSY WIRE TUBE

AC UNIT

ty FIG.4b

TABLE 4 Dimensions and Weights

Items Width X Depth X Height Weight

PTV44.9ingss0mm(W) X 9.98inpss.smm(D) X 65.75inj.670mm) (H)242-Ibsj1 104s)
BILLBOARD45 Ainii.iszmmj(W) X 17.9injssamm) (D) X 11.7inps7mm) (H)33-Ibsiiskg)
FRONT CABINET45.3inj1,130mmj(W) X 35.3injsosmmj(D) X 39.6in(.00smm) (A)215.6-Ibspoxxs)
REAR CABINET56.5injis3smm(W) X 65.6inj.665mm(D) X 42.5inj.os0mm) (H)545.6-Ibsj2ssks)

COMPRESSOR BOX | _43.9inj.tismm(W) X_20.3injsismmj (D) X_30.5injr7smmj (H) 156-lbsiriks)

Page 20
  • ACCESSORIES

When transporting the machine, make sure that the following parts are supplied.

TABLE 5a ACCESSORIES

DESCRIPTION OWNERS MANUAL KEY MASTER Part No. (Qty.) 420-6659-01 (1) 220-5576 (2)

Note For opening/closing the doors Figures If Part No. has no description, the Number has not been KEY (2) registered or can not be registered. Such a part may not be | For the CASHBOX DOOR obtainable even if the customer desires to purchase it. The Keys are inside the Coin Therefore, ensure that the part is in safekeeping with you. | Chute Door at the time of shipment from the factory.

SERVICE MANUAL NAOMI ENG VOL CONT B-5K OHM 420-6455-01 (1) 220-5373) INSTRUCTION MANUAL FOR THE 220-5484

GAME BOARD Spare, see Section 12.

SEAL TAPE 090-0037 (1) Used for the maintenance of Air Drive, for air leakage prevention.

Remote Controller used for adjustment of the projector. See Section 14. 200-5536(1) AIR CLEANER The Remote Controller is attached to 601-8188 (2) the Projector at the time of shipment. For spare, refer to Section 10.

Page 21

FUSE 7A CARTON BOX 514-5036-7000 (1) 601-10532 (1) Spare, see Section 17. Used for transporting the GameBoard. See FIG 5.

Page 22

HOW TO USE THE CARTON BOX

When requesting for the replacement/repair of this product's Game Board (NAOMI BOARD), follow the instructions below. Transporting the Game Board in an undesignated status is unacceptable. An erroneous handling can cause parts

IMPORTANT! damage. Put the Game Board in the Carton Box together with the Shield Case. Do not unnecessarily disassemble nor remove parts. By paying careful attention to the following Figure and the direction shown by on-Carton-Box printing, put the Shield Case in the Carton Box. When putting the Shield Case in the Carton Box, do not remove Leg Brackets. The projected portions of the packing material is intended for cushioning. Therefore, do not bend the projected portions.

"CHECK SIDE" Display

FILTER BOARD,

Jom

4 SX ected portions of

“> sire packing material,

FIG. 5

Bend the packing material in numerical order, and wrap the Shield Case with the packing material and put it in the Carton Box as shown. Putting it upside down or packing otherwise in the manner not shown can damage the Game Board and the parts.

Page 23

The following Table 5b lists the parts that had been separately packed when the product was shipped from the factory but are necessary when you use the product. These parts will be mounted on the product when installing and assembling it.

TABLE 5 b

AC Cable (Power Cord)WIRE HARN EARTH W/LUGCORD CLAMP
600-6729) <For TAIWAN>M6280-5009-01 (1)
600-7228 |!600-6664-02 (1)Used for installation,
600-6695 (1) <For USA><For TAIWAN>see 5 of Section 6.

600-6619 (1) <AC 220V HONG KONG> 600-6618 (1) <AC 220 ~ 240V AREA> Used for installation, see 5 of Section 6. Used for installation, see 5 of Section 6.

The following Table Sc lists the parts that are necessary when setting for the communication play. Flex Tube, Connector 29 and Fiber Plate had been assembled when the product was shipped from the factory. (See Section 20.)

FLEX TUBE 310-5285-290100 (1)

Assembled Flex Tube

FIBER PLATE CONN 29 WRG-0502 (2) 310-5286-29 (2)

Page 24

ASSY FIBER CABLE NUMBER STICKER 600-6275-0700 (2) WRG-0003 (1) 1 set of every two sheet sticker, the number 2, 3 and 4.

Page 25
  • ASSEMBLING AND INSTALLATION

comply with the instructions can cause electric shock hazard.

WARNING! Perform assembling as per this manual. Since this is a complex machine,

erroneous assembling can cause an electric shock, machine damage and or not functioning as per specified performance. When assembling, be sure to use plural persons. Depending on the assembly work, there are some cases in which working by one person alone can cause personal injury or parts damage. Ensure that connectors are accurately connected. Incomplete connections can cause electric shock hazard. Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards. Do not carelessly push the PTV. Pushing the PTV carelessly can cause the PTV to fall down. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause a severe accident such as electric shock. Failing to comply with this instruction can cause a severe accident such as electric shock to the player during operation. Provide sufficient space so that assembling can be performed. Performing work in places with narrow space or low ceiling may cause an accident and assembly work to be difficult. To perform work safely and avoid serious accident such as the cabinet's falling down, do not perform work in places where step-like grade differences, a ditch, or slope exist.

A Perform assembly work by following the procedure herein stated. Failing to

secure and stable condition. Performing work without using the step can cause

CAUTION! violent falling down accidents.

AY To perform work safely and securely, be sure to prepare a step which is in a

When carrying out the assembling and installation, follow the following 7-item sequence.

ASSEMBLING THE PTV

WIRING CONNECTIONS BETWEEN THE CABINETS

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

REMOVING THE SHIPPING BRACKET

POWER SUPPLY, AND EARTH CONNECTION

TURNING POWER ON IB ESeS8

ASSEMBLY CHECK

Page 26

Tools required for the work

KEY MASTER

WRENCH (for M16 hexagon bolt)

Box nut screwdriver (for M4 hexagon nut) or WRENCH

1 ASSEMBLING THE PTV

©) Fix the two mask holders onto the PTV top panel each with the 2 countersunk-head screws. @) Insert the TV mask from the underside as illustrated below, and secure with a total of 6 screws. ® Fix two PTV holders onto the PTV front side each with the 2 screws.

COUNTERSUNK-HEAD SCREW (2 each)

MASK HOLDER

TRUSS SCREW (2) rt M5S X 25, flat washer used. SS

A é

/SCREW (4) FIG. 6.1 MS X 20. w/flat & spring washers /PTV HOLDER

SCREW (2 each) iat & spring washers

Page 27

@) Mount the PTV onto the Front Cabinet. When performing this work, be sure to use 4 or more persons.

FIG. 6. 1b

® Fix between the PTV and the Front Cabinet on the Cabinet's both sides with 2 screws for each.

© While supporting the Billboard by 2 persons, another person using a step is to connect the Billboard wire connector into the terminal board of the PTV top panel.

SCREW (2) lat & spring washers

kK BILLBOARD

Connect the Connector.

FIG. 6. 1d TRUSS SCREW (2 each) MS X 30, flat washer mi

When performing this work, be sure to use 2 or more persons and be sure to use a step.

Page 28

Insert the Billboard into the holder bracket, fix to PTV with the 2 screws.

Remove the 2 truss screws;

dismount the lower lid form the Front Cabinet's face side.

TRUSS SCREW (black) M4 X25

LOWER LID;

PHOTO 6. la

(©) Connect two wire-connectors inside the Front Cabinet into the PTV connector panel. The connection angle is fixed. Easy to fix them arranging the angle and the orientation of each connector. Be sure of the correct connection in order to prevent the damage of the connector or the terminal portion. There are fixed screws both sides of the Video signal (D-sub) connector. Fasten them securely.

Connect the Connector.

PHOTO 6. 1b

Page 29

WIRING CONNECTIONS BETWEEN THE CABINETS

Perform the cabinet-to-cabinet wiring. With the ASSY Wire Tube, which installed to the Rear Cabinet at the time of shipment, connect between the Front Cabinet and the Rear Cabinet.

®rRemove the fixed 4 truss screws

and remove the front cabinet side Tube Bracket of the ASSY Wire Tube from the Rear Cabinet.

@ Reinstall the removed 4 truss

screws into the Rear Cabinet.

TRUSS SCREW (4),black M4X 12

PHOTO 6. 2a

  • There are one earth wire and a total of seven wire connectors in the front cabinet side of the ASSY Wire Tube. Connect the earth wire to the earth terminal stud on the Connector Panel of the Front Cabinet. Fasten with the hexagon nut in the order of the round earth terminal, the flat washer and the spring washer.

) Connect the seven wire connectors to each terminal on the Connector Panel of the Front Cabinet.

HEXAGON NUT M4, flat & spring washers used.

PHOTO 6.2b

Page 30

© Install the Tube Bracket to the Front Cabinet, and fix it with the 4 truss screws by using care so as not to damage the wiring.

TRUSS SCREW (4),black MS X 20

PHOTO 6.2 ¢

Page 31

3 SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Make sure that all of the adjusters are in contact with the floor. If they are not, the cabinet can move and cause an accident.

WARNING!

This product has 8 casters (4 for FRONT CABINET, 4 for REAR CABINET) and 8 Adjusters (4 for FRONT CABINET, 4 for REAR CABINET). (FIG. 6. 3a) When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm from the floor and make sure that the machine position is level. CASTER

(@) Transport the product to the the player to get on and off. fa @ Have all of the Adjusters make

installation position. Be sure to provide adequate space allowing

contact with the floor. Adjust the Adjuster's height by using a wrench so that the machine [| position is kept level. Q) Re 4 @ After making adjustment, fasten |_| the Adjuster Nut upward and /ADJUSTER secure the height of Adjuster (FIG. 6.3 b). FIG. 6.3a BOTTOM VIEW

_ADIUSTER WYLLLLLL CASTER

fe}

; Approx.5mm >

\ ADJUSTER FIG. 6.3 b ADJUSTER

10cm 15cm FIG. 6.3¢ FIG. 6.3 d

Refer to this Fig. (Scale:1/100) for Be sure to provide space as shown between the Air the layout of the place of installation. Vent and the wall surface.

Page 32

REMOVING THE SHIPPING BRACKET

@ Before turning the power on, be sure to remove the Sipping Brackets. Turning power on without removing the Sipping Brackets may cause the parts damage. @ Keep the Sipping Brackets carefully. Removing the product without the Sipping Brackets can cause parts damage.

At the time of shipment, the Shipping Brackets are secured to rear both sides of the Ride. By taking out 2 screws from each bracket, remove the Shipping Brackets. Reinstall the removing screws as before.

SHIPPING BRACKET L (OPPOSITE SIDE: R)

TRUSS SCREW (1); (TRUSS SCREW (1) M4X8 M4 X 12

PHOTO 6. 4

Page 33

5 POWER SUPPLY, AND EARTH CONNECTION

WARNING! Be sure to independently use the power supply socket outlet equipped with an Earth Leakage Breaker. Using a power supply without an Earth Leakage Breaker can cause a fire when electric leakage occurs. Ensure that the "accurately grounded indoor earth terminal" and the earth wire cable are available (except in the case where a power cord plug with earth is used). This product is equipped with the earth terminal. Connect the earth terminal and the indoor earth terminal with the prepared cable. If the grounding work is not performed appropriately, customers can be subjected to an electric shock, and the product's functioning may not be stable. Ensure that the power cord and earth wire are not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord and wire can cause electric shock and short circuit accidents. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering. After wiring power cord on the floor, be sure to protect the power cord. Exposed power cord is susceptible to damage and causes an electric shock accident.

The AC Unit is mounted on the right side of the machine. The AC Unit has Main SW, Circuit Protector, Earth Terminal and the Inlet which connects the Power Cord.

®© Ensure that the Main SW is OFF.

Main SW off MAIN SW

CIRCUIT PROTECTOR ®

EARTH TERMINAL Connect with the indoor earth terminal. AC Cable (Power Cord) 4a os FIG. 6. 5a AC UNIT

Page 34

@) Connect one end of the earth wire to the AC Unit

earth terminal, and the other end to the indoor earth terminal. The AC Unit earth terminal has a Bolt and Nut combination. Take off the Nut, pass the end of earth wire through the Bolt, and fasten the Nut. Connect the Earth Wire to the Earth Terminal.

® Note that the Earth Wire is incorporated in the Power

Cord for the Areas of AC 120V (USA) and AC 220 ~ 240V, and therefore, this procedure is not necessary. >

FIG. 6.5 b Earth Wire Connection

@ Firmly insert the power plug into the

socket outlet. Insert the opposite side of Power Cord plug to the AC Unit's connector ("INLET").

® Perform wiring for the Power Cord

and Earth Wire. Install protective covering for the Power Cord and Earth Wire.

Wiring Cover

FIG. 6. 5c Connecting Power Cord and Earth Wire

In case the Power Plug is apt to come out of place, secure the

Power Cord to the periphery of the AC Unit with the Cord Clamp (an accessory).

HOW TO USE THE CORD CLAMP

Page 35

6 | TURNING POWER ON

@ When the power is turned on, the ride portion moves. To prevent injury, first check for safety in the periphery of the ride and then turn power on.

WARNING! @ If ERROR is displayed in the ADVERTISE mode, do not operate the

machine. Operating the machine when ERROR is displayed can cause serious hazard.

initialization settings are automatically finished. Touching the ride portion during setting can cause inaccurate settings and unsatisfactory functioning during game play.

S During initialization settings, do not touch the ride portion. Wait until the

IMPORTANT!

Turn the AC Unit Main SW ON to turn on the machine's power supply. At the same time the power is turned on for the power supply, the machine starts the initialization setting movements and displays the screen on which the setting is being made. Do not touch the Ride until the initialization setting movements are automatically finished. © Approximately 5 seconds after the power is turned on, the compressor starts to operate. If the pressure inside the tank is insufficient, it takes several minutes to attain the preset pressure. At the time of installation assembly, it takes approximately 3 minutes. When operation is being continued, it takes approximately one and half minutes due to the prestress. @ The ride portion secures the left/right inclination to the center.

® The front of the ride portion @ The front of the ride portion is

lowers.

raised.

6) The front of the ride portion

moves to the intermediate position in the up/down movement. ©The front of the ride portion lowers. @ The compressor stops. FIG. 6. 6

After finishing the initialization setting movements, the ADVERTISE mode returns. During the setting movements, if any irregularity, malfunctioning, etc. of the moving mechanism are found, ERROR display is shown on the lower part of the ADVERTISE mode screen. In this case, the machine will not operate satisfactorily. Please contact the Distributor, etc. where this product was purchased from. In the case where several machines are connected, network check is performed after initialization settings are finished, and the screen displays to the effect that the check is being conducted. After checking, the ADVERTISE mode returns. Normally the network checking takes 1 ~ 3 minutes. If there is any irregularity in the communication connection, check screen display will continue.

Page 36

ASSEMBLY CHECK

In the TEST MODE, ascertain that the assembly has been made correctly and IC BD is satisfactory (refer to Section 9). In the test mode, perform the following test:

({1]) MEMORY TEST

RAM TEST Selecting the RAM TEST in the test mode menu causes the on-board memory to be tested

1C29 GOOD automatically. The game board is satisfactory if

1C35 GOOD the display beside each IC No. shows GOOD. IC09 GOOD IC10 GOOD IC11 GOOD IC12 GOOD IC16 GOOD IC18 GOOD IC20 GOOD IC22 GOOD IC17 GOOD IC19 GOOD IC21 GOOD 1C23 GOOD

PRESS TEST BUTTON TO EXIT

({2]) C.R.T. TEST

CRT. TEST 1/2 In the test mode menu, selecting C.R.T. TEST allows the 1 32 screen (on which the projector is tested) to be displayed. Although the projector adjustments have been made at the RED time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnetism, the location building's steel frames and other game machines in the BLUE periphery. By watching the test mode screen, make

judgment as to whether an adjustment is needed. If it is

necessary, adjust the projector by referring to Section 14. GREEN

WHITE

PRESS TEST BUTTON TO CONTINUE

C.R.T. TEST 2/2

PRESS TEST BUTTON TO EXIT +"

Page 37

(B] ) SOUND TEST

SOUND TEST

RIGHT SPEAKER OFF LEFT SPEAKER OFF -> EXIT

SELE WITH SERVICE BUTTON AND PRESS TEST BUTTON

[4]) INPUT TEST

INPUT TEST

HANDLE BAR OH ROLL OH THROTTLE LEVER FFH PITCH OH

START OFF VIEW OFF SAFETY SENSOR, OFF SERVICE OFF TEST OFF

PRESS TEST AND SERVICE BUTTON TO EXIT

({5]) OUTPUT TEST

OUTPUT TEST

> START LAMP OFF VIEW LAMP OFF EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON In the test mode, selecting SOUND TEST causes the screen (on which sound related BD and wiring connections are tested) to be displayed. Be sure to check if the sound is satisfactorily emitted from each speaker and the sound volume is appropriate.

Selecting the INPUT TEST on the test mode menu screen causes the screen (on which each switch and V. R. are tested) to be displayed. Press each switch. If the display beside each switch indicates "ON," the switch and wiring connections are satisfactory. Check the display of each V.R. value. If the V. R. is malfunctioning, refer to Sections 11 & 12.

In the output test mode, carry out lamp test to ascertain that each lamp lights up satisfactorily.

Perform the above inspections also at the time of monthly inspection.

Page 38
  • PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE

A

WARNING!

AN

CAUTION!

Do not push PTV from the back. Pushing the PTV from the back can cause the PTV to fall down. Push it from the side. When moving the machine, be sure to pull out the plug from the power supply. Moving the machine with the plug as is inserted can cause the power cord to be damaged, resulting in a fire and or electric shock. When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords and earth wires. Damaging the power cords can cause an electric shock and or short circuit. In places where step-like grade differences exist, be sure to separate the PTV, PTV Base, and the Cabinet. Inclining the PTV as is mounted on the PTV Base can cause the PTV to fall off from the Base and result in injury. When lifting the cabinet, be sure to hold the catch portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions due to the empty weight of the cabinet, and cause personal injury. When moving the PTV, do not push it from the rear side. Push it from sideways. Pushing the PTV from the rear side can have the PTV fall down, causing personal injury etc. In case the floor has slanted surfaces or step-like differences, be sure to move the machine by 2 or more persons.

Keep the Sipping Brackets carefully. Removing the product without the Sipping Brackets can cause parts damage.

\W GRIP PORTION

eS

On level surfaces,move the machine by causing FIG. 7a the Casters to make contact with the surfaces.

Page 39

When transporting the product in places with steps or step-like differences in grade, disassemble into each unit before transporting.

FIG. 7b

Page 40
  • CONTENTS OF GAME

The following explanations apply to the case the product is functioning satisfactory. Should there be any moves different from the following contents, some sort of faults may have occurred. Immediately look into the cause of the fault and eliminate the cause therefore to ensure satisfactory operation.

System Behavior in Advertising (Plying-for-Hire) Mode

While the power is connected to the system, the fluorescent light on the billboard is kept on. In an advertising mode, the system opens an operation explanation screen or a ranking data screen. The view button flashes when the screen explains how to operate the view button. Located on the left and right ends of the cabinet, the speakers output audio information. You may set the ADVERTISE SOUND item to OFF on the GAME ASSIGNMENTS screen so that this audio output function is disabled in an advertising mode. The start button flashes when the screen displays the PRESS START BUTTON message. This PRESS START BUTTON message appears in two cases; when the credit reaches a gamestartable level in an advertising mode and shortly after opening the operation explanation screen.

Fluorescent lamps are lit,

Image output on the monitor.

Emits sounds.

Throttle Lever

View Button (Change the viewpoint)|

FIG. 8a External View of the Cabinet

Page 41

Features of the WaveRunner GP

It provides several marine scenes where a cruising course appearance varies from play to play. The WaveRunner GP game features:

+ Effects of Stern Wave A stern wave is the wave produced on the wake of a boat. If your boat runs on the stern waves produced by another boat, it may jump unexpectedly, reduce its speed, or meet any other navigating difficulty. You must prevent your boat from running on the ster waves and navigate it with attention to where and how other boats are moving.

+ Water-Level-Depending Jumps A large jump (or a group of small jumps) may appear on the course when a water level is lower (or higher). The jump that was submerged on your first round cruise may be above the water on your second round cruise. Therefore, you must navigate your boat differently and/ or change a cruising path, from cruise to cruise, so that you can use an approaching jump.

How to Play

+ Insert the coin(s).

+ Make sure that the screen shows the PRESS START BUTTON message and that the start button flashes, and then climb onto the seat.

+ Press the start button, and make sure that the operation explanation screen appears. (See the

note | below.)

+ Wait until the time is counted down to 0 (zero) on the operation explanation screen or alternately press the start button to exit the screen. In either case the COURSE SELECT screen appears.

Highlights a selected course.

Illustrates a course layout. ———_—~_ are

Shows an image of the

selected course. Indicates a limit time for a course selection.

; by ning Indicates how to operate { the handlebars. the handlebars and the throttle lever.

Page 42
  • The system provides three courses: NOVICE, INTERMEDIATE, and EXPERT. These are displayed on the upper part of the screen. The selected course is highlighted. To migrate from one course to another, turn the handlebars leftwards or rightwards. To decide a course, squeeze the throttle lever. (See the note 2 below.)

MOTION STOP SWITCH.

Turn the handlebars left/right panel throttle lever to to choose the course. ecide a course.

a

View button FIG. 8¢ Start button

+ Wait until the time is counted down to 0 (zero) on the screen, and then the game starts. (See the note 3 below.)

+ Make sure that the boat starts to move at this moment.

  • The screen shows some information; your ranking position among the players (on its upper right part), a limit time (upper middle), your lap time, best lap time record, and best total time record (upper left), a tachometer and a speed meter (bottom right), and a speed-down gauge (bottom left). The speed-down gauge indicates a reduction of the cruising speed as a result of your boat running on the stern waves. It is dimmed when your boat is not running on the stern waves.

Limit Time

Player's Lap Time

Tachometer and Speed-Down Gauge Speed Meter (It is dimmed when your boat is not running on the stern waves.)

FIG. 8d

Page 43

+ When your boat runs on the stern waves, the speed-down gauge is undimmed and its triangle becomes filled with shade. If you keep your boat running on the stern waves, the triangle is shaded more and more. When the triangle is fully shaded, a warning message "Get out of the wake!" appears on the screen. If you make your boat off the stern waves at this moment, the speed-down gauge is again dimmed. If not, it is initialized to 0 (zero) and becomes filled with shade again.

=» SPEED DOWN =» SPEED DOWN Eas Se Initially the gauge is dimmed. When the boat runs on the stern When the gauge is fully waves, the gauge is undimmed shaded, a warning message and becomes filled with shade. appears.

FIG 8e

+ When the game starts, the system starts counting down the limit time. If you successfully pass a checkpoint on the course within the limit time, the bonus time is added to the remaining time. If not, the game is over. (See the note 4 below.)

+ For any course of NOVICE, INTERMEDIATE, or EXPERT. When you have successfully cruised around it two times, you reach the goal and the game is over. (See the note 5 below.)

  • To navigate the boat while playing the game, use the throttle lever and the handlebars, and tilt up the boat by shifting your body. To increase a cruising speed, squeeze the throttle lever while to decrease un-squeeze. To turn the boat leftwards and rightwards, turn the handlebars leftwards and rightwards respectively. To quickly turn the boat, turn the handlebars and then tilt up the boat to a turning direction of the handlebars. Note that just tilting up the boat without turning the handlebars does not enable to turn the boat. Press the view button to toggle a viewpoint between a navigator's point and a rearward point.
  • When reaching the goal, you can register your name if your lap time is good. Your registered name will be ona screen's ranking list in an advertising mode.

NOTES:

  • For an interactive communication play. Insert the one-play worth of coin(s) on the operation explanation screen and press the start button to enter the race. The system opens the entry screen where you wait until an opposition will enter the race by also inserting the one-play worth of coin(s) and pressing the start button. The entry screen closes and the operation explanation screen opens automatically, when a limit time is counted down to 0 (zero).
  • For an interactive communication play. When every player, after entering the race, has finished selecting a course, the racing course is decided by majority. In case of a tie, the course with a lower difficulty level is chosen.
  • Alternately, you can press the start button to decide a course.
  • For an interactive communication play. The bonus time is added to the remaining time when a leading player passes a checkpoint. The place of a player is indicated as 'place/the number of players' (e.g. 2/4 for a 4-player race, 1/2 for 2-player race). A player number, as 1P and 2P, is shown above the head of a playing character on the screen.
  • You cannot change the number of rounding cruises.
Page 44

Outline of the Courses

Three cruising courses are provided as below. Note that they are different from each other not only in the difficulty level but also in the appearance and device.

Novice Course This course gives the image of a tropical island against a blue sky where the hot sun grills white beaches. Generally, this novice course curves very gently. There are three checkpoints including a starting point. When your boat approaches a palm tree, the coconuts will fall down on your cruising path. Three dolphins may appear on the way and accompany your boat. The key part for reaching the goal is located at the end of the course that is sharply curved and enclosed with the cliffs.

Intermediate Course This course gives the image of a thick rainforest with mysterious remains. Generally, this intermediate course is a very narrow river with rather many curves. There are four checkpoints including a starting point. The highlight of this course is a jump from the 50-meter giant waterfall. In the mangrove woodlands, tall mangroves block your boat. You must be careful not to let it hit against them. Big snakes and giant fishes produce an atmosphere of rainforest. The key parts for reaching the goal are the curves located short of the giant waterfall, in the mangrove woodlands, and in the cave at the end of the course. You must navigate your boat with careful attention to these curved spots.

Expert Course This course gives the image of a waterfront where the surrounding skyscrapers are blazing in the evening darkness. This expert course features several combinations of a straight path and a sharp curve. There are four checkpoints including a starting point. All the scenes (the likes of the Brooklyn Bridge, the Statue of Liberty, and the Broadway with loud neon signs and large illumination bulletin boards) produce an atmosphere of big city. The key part for reaching the goal is the sharp curves located immediately after the straight paths.

Page 45
  • EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable. NAOMI GAME BOARD is used for the product. The system of this game board allows another game to be played by replacing the ROM Board Case mounted on the NAOMI CASE. As such, the Test Mode of this system consists of the System Test Mode for the system to execute SELF-TEST, COIN ASSIGNMENTS, etc. used in common for the machines employing the NAOMI BOARD, and the Game Test Mode for the specific product to execute Input/Output test for the operation equipment, difficulty setting, etc.

When the 2 or more machines are linked for communication play, be careful to enter the TEST mode. If one of the machines linked enters the TEST mode, all others display the NETWORK CHECK screen.

IMPORTANT!
Page 46

TABLE 10 EXPLANATION OF TEST MODE ITEMS DESCRIPTION aad

INSTALLATION | When the machine is installed, perform the following: SERVICE MANUAL OF MACHINE 1. Check to see that each setting is as per standard setting made at | 9-3d the time of shipment.

  • In the INPUT TEST mode, check such input devices as each 9-3b SW, V.R., etc.
  • In the OUTPUT TEST mode, check such output devices as 9-3 lamps, motors, etc.
  • In the self-test mode, check ICs on the IC Board. SERVICE MANUAL
MEMORYChoose the board test item in the MENU mode to allow the self-SERVICE MANUAL

test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked.

PERIODIC Periodically perform the following:

SERVICING1. Self-TestSERVICE MANUAL
  • Ascertain each setting. 9-3d, €
  • In the INPUT TEST mode, test the control device. 9-3b
  • In the OUTPUT TEST mode, check such output devices as 9-3 lamps, motors, etc.
CONTROL1. In the INPUT TEST mode, check such input devices as eachSERVICE MANUAL

SYSTEM SW, V.R., etc.

  • Adjust or replace each SW and VR. 9-3e
  • If the problem can not be solved yet, check the control's moves. | 11,12
MONITORIn the MONITOR ADJUSTMENT mode, check to see if theSERVICE MANUAL

PROJECTOR adjustment is appropriately made. 14

IC BOARD1. Self-TestSERVICE MANUAL
  • In the SOUND TEST mode, check the sound related ROMs. SERVICE MANUAL
DATA CHECKCheck such data as game play time and histogram to adjust theSERVICE MANUAL

difficulty level, etc. 9-3h

Page 47

9-1 SWITCH UNIT AND COIN METER

Do not touch places other than those specified. Touching places not specified can an ele

Adjust to the optimum sound volume by considering the environmental requirements of the installation location. If the COIN METER and the game board are electrically disconnected, game play is not possible.

SWITCH UNIT TEST BUTTON

Open the coin chute door, and the switch unit SOUND VOLUME SERVICE BUTTON shown will appear. The functioning of each SW is as follows:

Test SERVICE

FIG. 9. 1 a SWITCH UNIT

TEST BUTTON:For the handling of the test button, refer to the following pages.

(TEST)

SERVICE BUTTON:Gives credits without registering on the coin meter.

(SERVICE)

SOUND VOLUME:Adjust the Speaker Volume.

(SOUND VOLUME)

COIN METER

Open the Cashbox Door with the exclusively used key and the COIN METER will appear underneath the Cashbox.

COIN METER

FIG. 9. 1 b COIN METER

Page 48

9-2 SYSTEM TEST MODE

The contents of settings changed in the TEST mode are stored when the test mode is finished from EXIT in the menu mode. If the power is turned off before the TEST mode is finished, the contents of setting change become ineffective. Executing "BACKUP DATA CLEAR" in the SYSTEM TEST MODE does not clear the BOOKKEEPING data in the GAME TEST mode. Entering the TEST mode clears fractional number of coins less than one credit and BONUS ADDER data. Perform setting as per specified in this manual for operation. If setting not specified is performed for operation, proper function of this product may not be obtained.

In the SYSTEM TEST MODE, IC BD functioning can be checked, the monitor adjusted, and the coin setting performed. Refer to NAOMI SERIVCE MANUAL for the details. Note that the setting of the following items need to be performed in accordance with the instruction given.

+CABINET TYPE:IPLAYER(S)
+MONITOR TYPE:HORIZONTAL
+SERVICE TYPE:COMMON

+ COIN CHUTE TYPE: COMMON

The SEQUENCE SETTING items of COIN ASSIGNMENTS are as follows.

  • SEQUENCE SETTING SEQUENCE 1: Number of credits required for starting the game. SEQUENCE 2: Number of credits required for continuing the play. SEQUENCE 3 ~8: NOT USED
Page 49

9-3 GAME TEST MODE

As soon as it enters the Game Test mode, the Ride starts moving. Before entering the Game Test Mode, be sure to keep away a person(s) from the Ride. Since the

CAUTION! Ride moves momentarily, it may cause accidents.

@ The new settings will not take effect until the Game Test Mode is exited. When you make change to the settings, exit the Game Test Mode by proper operation. You must not attempt to demonstrate this game (for the selling purpose) with any other settings other than those specified in this document. Use of such settings may cause malfunctions or bad operation on the machine.

GAME TEST MENU

By selecting GAME TEST MODE from the System Test Menu Screen, the Game Test Mode Menu Screen is displayed as follows.

SYSTEM MENU

RAM TEST JVS TEST SOUND TEST C.R.T. TEST +

SYSTEM ASSIGNMENTS: GAME ASSIGNMENTS

COIN ASSIGNMENTS ngpeinnpectin a nat VOLUME SETTING BOOKKEEPING VALVE TEST BACKUP DATA CLEAR WIRING TEST CLOCK SETTING BOOKKEEPING

ROM BOARD T a DATA CLEAR

GAME TEST MODE ~ [DeRose sata a]

=e’ SELECT WITH SERVICE BUTTON

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

AND PRESS TEST BUTTON

System Test Menu Screen FIG. 9.3 a Game Test Menu Screen

+ Press the TEST Button to cause the following Test Menu to be displayed on the monitor.

+ Press the SERVICE Button until the pointer ">" is moved to the desired item to make a selection.

+ Bring the pointer ">" to the desired item and press the TEST Button to enter the selected item's test.

+ Inthe Test mode, the Start button instead of Test button and the View button instead of Service button can be used. These, however, can not be used in the INPUT TEST.

+ After the test is complete, move ">" to "EXIT" and press the TEST Button to return to the System Test Menu Screen.

Page 50

INPUT TEST

When INPUT TEST is selected, the following screen appears on the monitor. The screen allows the status of each SW and the value of each V.R. of the cabinet to be viewed. On this screen, periodically check the status of each switch & V.R.

INPUT TEST + By pressing each switch, if the display on the right-hand side of the name of each

HANDLE BAROHswitch changes to ON from OFF, the SW
ROLLOHiriC1otiiC1
THROTTLE LEVERFFHand the wiring connections are satisfactory.
PITCH0H.

+ When checking the SAFETY SENSOR, be

STARTOFFsure to intercept the 3 Sensors on the step.

VIEW OFF

SAFETY SENSOROFF...
SERVICEOFF+Simultaneously pressing the Service button
TESTOFFand the Test button returns the Game Test

Menu screen.

PRESS TEST AND SERVICE BUTTON TO EXIT

FIG. 9.3 ba INPUT TEST Screen

FIG. 9.5 b SAFETY SENSOR LIGHT EMITTER \ LIGHT EMITTER \ LIGHT RECEIVER Pe

LIGHT EMITTER \

LIGHT RECEIVER —————S$SS) Tc 0 > LIGHT RECEIVER/

The standard values for adjusting each V. R. are as follows: In this product, the item of VOLUME SETTING allows V. R. values except for PITCH to be set.

HANDLE BAR: 8 0 H+9 (centering position)

ROLL: 8 0 H+9 (centering position)

THROTTLE LEVER: e 0 H +9 (lever released) PITCH: Over 7 0 H (When the Ride is lowered) ~ Under e 0 H (When the Ride is raised)

4l www.seuservice.com

Page 51

OUTPUT TEST

The OUTPUT TEST allows the function of each lamp to be checked.

OUTPUT TEST

> START LAMP OFF VIEW LAMP OFF EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.3 c OUTPUT TEST Screen

TEST PROCEDURE

© Press the SERVICE Button to bring the arrow to the lamp item to be tested. @) Pressing the TEST Button causes "ON" to be displayed and the corresponding lamp lights up. Pressing the TEST Button again causes "OFF" to be displayed and the lamp goes off.

® Bring the arrow to EXIT and press the TEST Button to return to the Game Test Menu screen.

Page 52

GAME ASSIGNMENTS

Selecting the GAME ASSIGNMENTS in the menu mode causes the present game setting to be displayed and also the game setting changes can be made. Each item displays the following content. If the COMMUNICATION MODE is set to NO LINK, the items HANDICAP and CABINET ID will not appear.

GAME ASSIGNMENTS

GAME DIFFICULTY NORMAL COMMUNICATION MODE NO LINK

HANDICAP ON

CABINET ID 1

> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.3 d GAME ASSIGNMENTS Screen

@ GAME DIFFICULTY: The game difficulty can be differentiated by varying Time at the

time of starting the race and Time at the time of passing the

checkpoint. Choose one from among 3 categories, i.e., EASY, NORMAL and HARD.

@ COMMUNICATION MODE: Set up whether the communication (interactive) play is enabled. There are 3 categories, i.e. MASTER (for one machine/ player only), SLAVE (for communication play), and NO LINK (not for communication play).

@ HANDICAP: In the communication vs. play, this sets whether correction should

be made so that player boat in the second or lower positions

increase the speed. Correction is used with ON and use of correction is cancelled with OFF.

@ CABINET ID: When linked for communication play, allocate the numbers sequentially in order starting from the leftmost end.

For Communication play, refer to Section 20 "COMMUNICATION PLAY".

SETTING CHANGE PROCEDURE

Press the SERVICE Button to bring the arrow (>) to the desired setting change item.

@ Press the TEST Button to choose the desired setting item.

® Bring the arrow to EXIT and press the TEST Button to return to the Game Test Menu screen.

Page 53

VOLUME SETTING

CAUTION!

S

IMPORTANT! In this setting item, each V. R. value of the Handlebars, Roll, and Throttle can be set.

Performing settings while riding on the Ride is dangerous as the Ride moves. Use the Start button instead of Test button, and the View button instead of Service button.

When V. R. adjustment or replacement has been made, be sure to perform the setting in that particular V. R. value setting item.

VOLUME S PTING

> HANDLE BAR ROLL THROTTLE LEVER EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.3 ea VOLUME SETTING Screen

Page 54
  • HANDLE BAR VOLUME SETTING

HANDLE BAR VOLUME SETTING

MAX00(FF)
MIN00(01)
NEUTRAL00(80)

> EXIT WITHOUT SAVE EXIT WITH SAVE

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.3 eb HANDLE BAR VOLUME SETTING Screen

SETTING PROCEDURE

® In the V. R. setting menu screen, press the SERVICE Button to bring the arrow to HANDLE BAR.

@ Press the TEST Button to cause the HANDLE BAR VOLUME setting screen to appear.

® Turn the Handlebars fully to the left/right and then release.

  • Press the SERVICE Button to bring the arrow to EXIT WITH SAVE. © Press the TEST Button to have the Volume Setting Menu screen return to the screen.

© When setting other Volume values also, select the applicable select item.

@ Press the SERVICE Button to move the arrow to EXIT and press the TEST Button to return to the Game Test Menu screen.

Page 55
  • ROLL VOLUME SETTING

ROLL VOLUME SETTING

MAX00(FF)
MIN00(01)
NEUTRAL00(80)

> EXIT WITHOUT SAVE EXIT WITH SAVE

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.3 ec ROLL VOLUME SETTING Screen

Av ga

TTING PROCEDURE

® In the Volume Setting Menu mode, press the SERVICE Button to bring the arrow to ROLL.

@ Press the TEST Button to have the ROLL VOLUME setting screen appear on the screen.

® Incline the Ride fully to the left/right and then cause it to be in the level position.

® Press the SERVICE Button to bring the arrow to EXIT WITH SAVE.

© Press the TEST Button to have the Volume Setting Menu retum to the screen.

© When setting other Volume values also, choose the applicable setting item.

@ Press the SERVICE Button to move the arrow to EXIT and press the TEST Button to return to the Game Test Menu screen.

Page 56
  • THROTTLE LEVER VOLUME SETTING

THROTTLE LEVER VOLUME SETTING

MAX FF (GB) MIN FF (00)

> EXIT WITHOUT SAVE EXIT WITH SAVE

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 9.3 ed THROTTLE LEVER VOLUME SETTING Screen

SETTING PROCEDURE

® In the Volume Setting Menu, press the SERVICE Button and bring the arrow to THROTTLE LEVER.

@ Press the TEST Button to have the THROTTLE VOLUME SETTING screen appear.

® Fully grip the Throttle Lever and then release.

O) By pressing the SERVICE Button, bring the arrow to EXIT WITH SAVE. ® Press the TEST Button to have the Volume Setting Menu return on the screen.

(G) When setting other Volume values also, choose the applicable setting item.

@ Press the SERVICE Button to move the arrow to EXIT and press the TEST Button to return to the Game Test Menu screen.

Page 57

VALVE TEST

This test allows the functioning of each Air Valve, Limit SW and Volume to be checked.

the Start button instead of Test button, and the View button instead of Service A\ Performing settings while riding on the Ride is dangerous as the Ride moves. Use

CAUTION! |] button.

VALVE TEST

> PITCH VALVE & ETR CHECK ROLL VALVE & ETR CHECK EXIT

PRESS TEST BUTTON TO EXIT

FIG. 9.3 fa VALVE TEST Screen

ROLL _ETR RIGHT VALVE LEFT VALVE PITCH ETR PITCH VALVE

ETR UP VALVE | | ETR DOWN VALVE FIG. 9.3 fb VALVE Arrangement /

ROLL VALVE UP VALVE } \ DOWN VALVE

UP LIMIT SW) = DOWN LIMIT SW ae

FIG. 9.3 f c LIMIT SW Arrangement

FRONT CYLINDER

Page 58
  • PITCH VALVE & ETR CHECK

PITCH VALVE & ETR CHECK

PITCH VALVE DOWN UP VALVE ON ETR UP VALVE ON DOWN VALVE ON ETR DOWN VALVE ON PITCH ETR FOH UP LIMIT SW ON DOWN LIMIT SW ON PITCH VOLUME 46H

PRESS TEST BUTTON TO EXIT

FIG. 9.3 fb PITCH VALVE & ETR CHECK Screen

TEST PROCEDURE

© tthe VALVE TEST MENU, press the SERVICE Button and bring the arrow to PITCH @ Press the TEST Button to have the PITCH VALVE TEST screen appear (6) Turn the Handlebars to the right to raise the Ride ® Turn the Handlebars to the left to lower the Ride

VALVE & ETR CHECK.

@ Press the TEST Button to have the PITCH VALVE TEST screen appear.

  • Turn the Handlebars to the right to raise the Ride.

® Turn the Handlebars to the left to lower the Ride.

  • Position the Handlebars in the center to stop the Ride.
  • Gripping the Throttle Lever during ® ~ ® above increases the air pressure and releasing the Throttle Lever decreases the air pressure.

@ During ® ~ © , check the functioning of each Air Valve and Limit SW.

Press the TEST Button to return to the VALVE TEST Menu.

©) Choose EXIT and press the TEST Button to return to the Game Test Menu screen.

Page 59
  • ROLL VALVE & ETR CHECK

ROLL VALVE & ETR CHECK

ROLL VALVE ON RIGHT VALVE ON LEFT VALVE ON ROLL ETR FOH

ROLL VOLUME — 80H

PRESS TEST BUTTON TO EXIT

FIG. 9.3 fe ROLL VALVE & ETR CHECK Screen

TEST PROCEDURE

© Inthe VALVE TEST MENU, press the SERVICE Button and bring the arrow to ROLL @) Press the TEST Button to have the PITCH VALVE TEST screen appear

VALVE & ETR CHECK.

@) Press the TEST Button to have the PITCH VALVE TEST screen appear. ® Turn the Handlebars to the right, and the Ride is subject to the centering force from the right only.

@ Turn the Handlebars to the left, and the Ride is subject to the centering force from the left only. © Position the Handlebars in the center to stop the centering movement. GC) Gripping the Throttle Lever during ABA‘AD above increases the air pressure and releasing the Throttle Lever decreases the air pressure.

@ During 4BA‘AE, check the functioning of each Air Valve.

Press the TEST Button to return to the VALVE TEST Menu.

©) Choose EXIT and press the TEST Button to return to the Game Test Menu screen.

Page 60

WIRING TEST

Selecting WIRING TEST allows the communication between GAME BD and DRIVE BD to be checked automatically. Ifthe communication is satisfactorily conducted, "OK" is displayed and if any irregularity is found, "ERROR" will be displayed.

WIRING TEST

¢ & Re BO TE ORIADU EON Om mm RS ESTA SAMOA ERR ISR ke SS SEGRE GNIS VVVVVVV VV VV VV VV VV VV VV VV 1111110 1111101 1111011 1110111 1101111 1O1III1 Oll1i11 TLIII11 OllIII1 1O1III1 1101111 1110111 1111011 1111101 1111110 1L11111 TLII111 Oll1111 1O11I11 1101111 1110111 1111011 1111101 1111110 1111101 1111011 1110111 1101111 1O11I11 O1l1111 TLIDI1L T1111 Hone Hee ee ee eee oH ee ee ee eo ee Deep oonone ee te ene Se ree Locos

PRESS TEST BUTTON TO EXIT

FIG. 9.3 g WIRING TEST Screen

+ After finishing the test, if the above Figure is displayed, it is satisfactory.

+ After finishing the test, press the TEST Button to return to the Game Test Menu screen.

Page 61

BOOKKEEPING

Selecting the BOOKKEEPING in the menu mode displays the bookkeeping data up to the present on the following 12 screens. Press the TEST Button again to proceed to the next page. When you press the TEST Button during the display of this mode, you return to the Game Test Menu.

BOOKKEEPING 1/12

NUMBER OF GAMES 94 PLAY TIME(TOTAL) OD 2H 11M 11S PLAY TIME(1P) OD 2H 4M 2S PLAY TIME(VS) 0D 0H 7M 9S AVERAGE PLAY TIME OH 1M 23S LONGEST PLAY TIME OH 3M 47S SHORTEST PLAY TIME OH OM 2S

PRESS TEST BUTTON TO CONTINUE

FIG. 9.3 ha BOOKKEEPING (1/12) Screen

@NUMBER OF GAMES:Number of games played.
@TOTAL TIME(TOTAL):Total energized time.
@PLAY TIME(IP):Total playtime of one player game only.
@PLAY TIME(VS):Total playtime of communication game play.
Page 62
  • PLAY TIME HISTOGRAM

The time that players have been timeout is displayed in graph. It's a total of 2 screens.

PLAY TIME H

OMO0S ~ OMO09S 0M10S ~ 0M 19; 0M20S ~ 0M209; 0M30S ~ 0M395 OM40S ~ 0M49; OMS0S ~ 0MS59; 1MOOS ~ 1Mo9: IM10S ~ 1M109: 1M20S ~ 1M209: 1M30S ~ 1M30: IM40S ~ 1M49: 1MS0S ~ 1MS50: 2MO0S ~ 2M009; 2M10S ~ 2M19; 2M20S ~ 2M209; 2M30S ~ 2M39; 2M4o: 2MS50: ~2MS50S

PRESS TEST BUTTON TO CON BOOKKEEPING 2/12

OGRAM 1/2

iN}

Sy} RNUNNNBRENUAN OHH

NUE

PLAY TIME Hi

3Moo: 3M10: 3M20S 3M30: 3M4o: 3MSO: Moo: 4M10: 4M20: 4M30: 4M40S ~ 4M40S, 4MSOS ~ 4MS9S, OVER

TEST BU’ BOOKKEEPING 3/12

OGRAM 2/2

° ° ° ° ° ° ° °

TON TO CONTINUE

FIG. 9. 3h b BOOKKEEPING (2 - 3/12) Screen

Page 63
  • CLEAR TIME HISTOGRAM

The clear time of the player, which has made a goal, is displayed in graph. Screens are two screens in NOVICE, INTERMEDIATE and EXPERT, respectively. So it's a total of 6 screens.

BOOKKEEPING 4/12

CLEAR TIME HISTOGRAM 1/2 NOVICE oMo0es oMoos ° OM10S ~ OM19S ° 0M208 ~ ° M308 ° oM408s ~ ° OMS0S ~ ° 1Moos ° IM10S ~ 1M19S ° 1M20S ~ 1M29S ° 1M30S ~ 1M30S ° 1M40S ~ 1M490S ° 1MS0S ~ 1MS0S ° 2MO0S ~ 2Mo0oS ° 2M10S ~ 2M19S ° 2M20S ~ 2M29S ° 2M308 2M40s 2MS0S ~ ° ° °

PRES TEST BUTTON TO CONTINUE BOOKKEEPING 5/12

CLEAR TIME HISTOGRAM 2/2 NOVICE 3Moos ° 3BM1098 ° 3M20S ° 3M308 2 3M49s 1 3MS0S ° 4MOoS ° 4M108 ° 4M29S, ° 4M308 ° 4M40s ° ~4MS50S ° OVER SMOOS °

T BUTTON TO CONTINUE

BOOKKEEPING 6/12

CLEAR TIME HISTOGRAM 1/2 INTERMEDIATE. OMO0S ~ OMOOS ° OM10S ~OM19S ° 0M20S ~ 0M29S ° 0M30S ~ 0M30S ° 0M40S ~ OM49S ° OMS50S ~ OMS50S ° 1MOOS ~ 1Mo9S ° IM10S ~ 1M19S ° 1M20S ~ 1M29S ° 1M30S ~ 1M39S ° IM40S ~ 1M49S ° IMSOS ~ 1MS9S ° 2MOOS ~ 2Mo0o0S ° 2M10S ~2M19S ° 2M20S ~ 2M29S ° 2M30S ~ 2M30S ° 2M40S ~ 2M49S ° 2MS50S ~ 2M50S °

PRESS TEST BUTTON TO CONTINUE BOOKKEEPIN'

CLEAR TIME HISTOGRAM 2/2 NTERMEDIATE, 3MO0S ~ 3MO09S. ° 3M10S ~ 3M19S, ° 3M20S ~ 3M209: ° 3M30S ~ 3M39; ° 3M40S ~ 3M40S, ° 3MS0S ~ 3MS59S, ° 4MOOS ~ 4Mo9: ° 4M10S ~ 4M19S ° 4M20S ~ 4M20S ° 4M30: ° 4Ma4o: ° 4MS50S, ° OVER SMOOS °

TEST BUTTON TO CONTINUE

BOOKKEEPING 8/12

CLEAR TIME HI TOGRAM 1/2 EXPERT MOOS ~ OMO9S ° OM10S ~ 0M198 ° 0M20S ~ 0M29Ss ° OM30S ~ 0M39S ° OM40S ~ OM498S ° OMS50S ~ OMS50S ° 1MOOS ~ 1Mo9s ° IM10S ~ 1M19s ° 1M20S ~ 1M209s ° 1M30S ~ 1M309s ° 1M40S ~ 1M49s ° 1MS0S ~ 1M50s ° 2MOO0S ~ 2Moos ° 2M10S ~ 2M19S ° 2M20S ~ 2M20s ° 2M30S ~ 2M30S ° 2M40S ~ 2M49S ° 2MS50S ~ 2MS50S °

PRESS TEST BUT ON TO CONTINUE BOOKKEEPING 9/12

CLEAR TIME HISTOGRAM 2/2 EXPERT 3MO0S ~ 3MO09s ° 3M10S ~ 3M19S ° 3M20S ~ 3M20s ° 3M30S ~ 3M30S ° 3M40S ~ 3M49S ° 3MS50S ~ 3MS50S ° 4MOOS ~ 4Mo9S ° 4M10S ~ 4M19S, ° 4M20S ~ 4M209S ° 4M30S ~ 4M39S ° 4M40S ~ 4M40S, ° 4MSOS ~ 4MS59S ° OVER SMOOS °

PRESS TEST BUTTON TO CONTINUE

FIG. 9.3 he BOOKKEEPING (4 - 9/12) Screen

»seuservice.com

Page 64
  • Detailed data of each course

Allows for checking the detailed data of each course; NOVICE, INTERMEDIATE and EXPERT. It's a total of 3 screens on each course | screen.

annannan

PR! BOOKKEEPING 10/12

NOVICE 68

Ist68th1
2nd°oth2
3rd°10th=O.
4th°lithoO
Sth°12th1
6th°13thoO
7th214th56
‘HECKI17AVR.
*HECK215AVR.
*HECK311AVR.
“HECK48AVR.
*HECKS4AVR.
“HECK62AVR.

TEST BUTTON TO CONTINUE

BOOKKEEPING 11/12

INTERMEDIATE 15

Ist°8th°
2nd°oth1
3rd°10th1
ath°Lith1
Sth°12thoo
6th°13th1
7th114th10

° AVR. 7 AVR. 6 AVR. Ss AVR. 4 AVR. 1 AVR. ° AVR. ° AVR.

PRESS TEST BUTTON TO CONTINUE

BOOKKEEPING 12/12

EXPERT 8

Ist18th1
2nd°oth°
3rd°10thO.
4th°Lith1
Sth°12thoO
6th°13thoO
7h°14th5
KIsAVR.
K25AVR.
“K34AVR.
“Ka4AVR.
“KS3AVR.
K61AVR.
K7°AVR.
KR°AVR.

PRESS TEST BUT ON TO EXIT

FIG. 9.3 hd BOOKKEEPING (10 - 12/12) Screen @ 2nd line of the screen:

Indicates the course name and the

total playing time.

@ Ist - 14th:

Indicates the ranking at the play end time. (It's not whether the game was cleared or not.)

@ CHECK 1-6 or 8:

Indicates the number of players,

which arrived at each check-point.

@ AVR:

Indicates the average time of each

checkpoint section.

Page 65

BACKUP DATA CLEAR

Clears the contents of BOOKKEEPING. When clearing the data, use the SERVICE Button to bring the arrow to "YES (CLEAR)" and press the TEST Button. When clearing is finished, "COMPLETED" is displayed. Press the TEST Button again to return to the Game Test Menu screen. Bring the arrow to "NO (CANCEL)" and press the TEST Button to have the Game Test Menu screen return on the screen without clearing the data. Note that this operation does not affect the contents of the game setting.

BACKUP DATA CLEAR

YES(CLEAR) > NO (CANCEL)

SELECT WITH SERVICE BUTTON AND PRESS 1 T BUTTON

FIG. 9.3 he BACKUP DATA CLEAR Screen

Page 66
  • AIR DRIVE

In order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product.

WARNING! Be careful so as not to damage wirings. Damaged wiring can cause an

electric shock or short circuit accident. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause electric shock hazard. Do not insert hand into the mechanism so as not to cause hand and fingers

pinched in. Failure to observe this can cause a serious injury such as a

fracture. When performing work such as parts replacement other than those specified in this manual, be sure to contact where you purchased the product from and confirm the work procedures and obtain precautions prior to performing work. Inappropriate parts replacement and/or installing with erroneous adjustment can cause an overload or the parts to come into contact, resulting in an electric shock, a short circuit, and a fire.

Hot compressor can cause burn. After turning power off, wait until hot portions cool off to start working. Setting to an undesignated pressure can cause malfunctioning and trouble. Be !

CAUTION! sure to use the designated pressure.

Perform dewatering periodically. Gathered water can have compressor load become greater and cause malfunctioning. When the set pressure is adjusted, be sure to check if the adjustment is

  • 1)
IMPORTANT! appropriate.
Page 67

10 - 1 OVERVIEW OF AIR DRIVE SYSTEM

This product uses the compressor. Be sure to turn off the main switch of the AC Unit and start working after checking that the compressor motor has stopped.

@ brive Board

VALVE CYLINDER

@) compressor unit FILTER .

TANK UNIT REGULATOR VALVE CYLINDER

VALVE CYLINDER @earcurr prorecror POWER —— I

FIG. 10.1 a Air Drive System Schematic (©) COMPRESSOR UNIT / TANK UNIT Compresses and stores air by causing the AC Motor to turn the Compressor. @ FILTER / REGULATOR Filters foreign matter consisting of fine particles, and water contents in the compression air (primary side) stored in the COMPRESSOR UNIT and governs the compressed air to a preset pressure (secondary side). Two Regulators are equipped with: One for high pressure and the other for low pressure.

@) CIRCUIT PROTECTOR @ DRIVE BOARD (inside the Front Cabinet)

Protects the AC motor for the compressor from overcurrent.

The DRIVE BOARD controls the entire Air Drive System by activating or stopping the Compressor depending on the pressure inside the Compressor Unit, and by sending a signal to open/close each valve in accordance with the progress of game play.

br. yy ST / Scala COMPRESSOR a “=| FRONT CYLINDER

VALVE UNIT

mA REAR CYLINDER

REGULATOR eL

4.) TANK UNIT

  • te es Te ee FILTER) FIG. 10.1 b Overview of air drive system
Page 68

10-2 DEWATERING FROM THE AIR FILTER

Remove the Rear Lid of the Mechanism Base to have the water tank appear in the inner portion on the right-hand side. Although the Air Drive Mechanism of the product automatically dewaters the water from inside the Air Filter, dispose the water from inside the Air Filter by periodically dewatering (every day in the period of high humidity). Since the oilless compressor is used for this machine, the drain water can be discharged into a sewer system.

DEWATERING PROCEDURE

Tum the main switch of the AC Unit off.

@Take out the 5 screws to remove

the Rear Lid of the Mechanism Base (FIG. 10. 2 a).

TRUSS SCREW (5) M4 X 12, black FIG. 10.2a @ he Drain Tube from the Filter is connected to the water tank. Remove the Water Tank from the Mechanism Base by firmly holding the Drain Tube so as not to allow the tube to come off from the water tank.

@ When turning and loosening the drain nozzle

underneath the filter in the horizontal direction, water will gush out together with the compressed air. Be sure to firmly hold

an the Drain Tube so as not to allow the water

can splash out in the periphery (FIG. 10. 2 b). YAMAHA [pe o 4) | p [J p

Press the Drain Nozzle. one DRAIN vnsf \vane TANK

FILTER WATER TANK

Drain Nozzle, ~~ WATER TANK HIG, 10.2: Firmly hold the Tube. © The drained water can be discharged into a sewer system.

© After dewatering is finished, tighten the drain nozzle. Shake the end of the Drain Tube off to remove water thoroughly, put the tube end into the water tank, and return the water tank to the Mechanism Base.

Page 69

10 -3 DEWATERING FROM THE AIR TANK

Water accumulated in the tank increases the load on the Compressor, which may cause malfunctioning. The Tank should be dewatered at least once a week. Since the oilless compressor is used for this machine, the drain water can be discharged into a sewer system.

® Tum the main switch of the AC Unit off. @ Open the Rear Lid (refer to 10 - 2).

® Tum the main switch of the AC Unit off @ Open the Rear Lid (refer to 10 - 2) ® The Drain Cock and Drain

Tube are located on this side of the Air Tank. Pull out the Tube

and insert the end of the Tube

into the Accessory Water Tank or an appropriate container (FIG. 10. 3 a).

WATER TANK

FIG. 10.3 a

@ Tum the Drain Cock by 90

degrees to have the compressed air and water discharged. If the cock is not transferred little by little, water will splash out. At

this time, hold the tube tight so ap

Twirl a 90 degrees. water may not splash out or on your body (FIG. 10. 3 b).

Hold the end of tube tight.

FIG. 10.3b

Afier the water is discharged, close the Drain Cock, remove the remaining water from the end of the air tube and put the tube into the cabinet.

© The drain water can be discharged into a sewer system.

Page 70

10 -4 REGULATOR

The compressed air (primary 6.0kgficm? side) in the air tank is governed to preset pressures by regulators before the air pressure is sent to the cylinders. Check set pressure every 2 months. Remove Lid Left from the Mechanism Base (refer to 11-1) to have the Regulator Unit appear, and check the pressure E— with the Pressure Gauge S, attached to each Regulator. If the pressure within the Compressor is insufficient, the

Regulator's Pressure Gauge will

not indicate the correct value. When checking, first turn the =

Main SW on and wait until the HIGH V LOW HIGH VY LOW

Compressor operation stops. PULL DOWN PULL DOWN Pressure settings given at the time of shipment are shown in FIG. 10. 4. e

FIG. 10.4

If the actual pressure is different from the set pressure, adjust it as follows: Before proceeding the work, be sure to turn the Main SW off. However, if the pressure within the Compressor is insufficient, adjustments can not be performed correctly. First, turn the Main SW on, and after the Compressor operation stops, turn the SW off, and then proceed the work.

Method of adjustment pull down the Adjustment Knob of the Regulator until a click is heard @ Turn the Adjustment Knob to make adjustment to the preset pressure

pull down the Adjustment Knob of the Regulator until a click is heard.

@ Turn the Adjustment Knob to make adjustment to the preset pressure. ® When the correct setting is established, push up the adjustment knob until a click is heard.

  • After the setting is finished, play game and check the regulator's pressure gauge once again.
Page 71

10 -5 AIR CLEANER

The Compressor for this machine is the oilless type and so oil replenishment is not necessary. However, if the Air Cleaner for protecting the Compressor becomes dirty, the Compressor's operation efficiency will decrease, and this may cause malfunctioning. Two spare Air Cleaners are available. Check the Air Cleaners every 2 months.

® Tum the main switch of the AC

Unit off.

@ Take out the 4 truss screws and

remove the Air Vent on the right side of the Rear Cabinet.

TRUSS SCREW (4) M4 X 8,BLACK

PHOTO 10. 5a

® Removing the Air Vent, the

Compressor's Cleaner Cover is

appeared. Taking out the fixed screws, remove the Cleaner Cover.

CLEANER COVER

PHOTO 10.5 b

@ Check the Air Cleaner inside the Compressor. If dirty, replace the

Air Cleaner.

PHOTO 10. 5¢

Page 72
  • MAINTENANCE OF MECHANISM UNIT
WARNING!
CAUTION! n order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product. Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident. After the power is turned off, close the Main Cock, and then start working. The Main Cock not closed can cause serious accidents resulting from cylinder movement, etc., due to some cause. Periodically retighten the designated bolts. Continuing business operation with the bolts as is loosened can cause serious accidents. When assembling, be sure to perform the work by plural persons. Depending on the assembly work, there are some cases in which performing the work by a single person can cause personal injury. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause electric shock hazard. Do not insert hand into the mechanism so as not to cause hand and fingers

pinched in. Failure to observe this can cause a serious injury such as a

fracture. When performing work such as parts replacement other than those specified in this manual, be sure to contact where you purchased the product from and confirm the work procedures and obtain precautions prior to performing work. Inappropriate parts replacement and/or installing with erroneous adjustment can cause an overload or the parts to come into contact, resulting in an electric shock, a short circuit, and a fire.

Immediately replace the important parts, which are intended for hazard

prevention, if damaged or omitted. Non- replacement of these parts can cause

accidents. Hot Compressor can cause burn. After turning the power off, wait until the high temperature portions cool off to start working.

The mobile parts of this machine need greasing once every 6 months. At the same time, retighten each installation bolts. Perform the above maintenance work after removing each Lid and the Bellows Brackets, as per the following procedure.

Page 73

11 - 1 REMOVE THE LID & THE BELLOWS BEFORE SARTING MAINTENANCE WORK

@tum the main switch of the AC Unit off.

@tum the main switch of the AC Unit off @ Take out the 5 screws to remove the Rear Lid. (See 10 - 2.)

® There are 2 Air Cocks inside the Rear Lid. Close the Main Cock on the left side by turning 90 degrees. (Fig. 11.1)

STEP L,

FIG. 11.1

@ Take out the 3 truss screws to remove Sash L (L

type fitting). (Photo 11.1a)

TRUSS SCREW (3) M4 X 12,chrome plated

PHOTO Il.1a

Page 74

® Take out the 3 truss screws. (Photo 11.1b)

TRUSS SCREW (3),black M5 X 12

PHOTO 11. 1b

© Remove Step L slowly. Use care when removing the Step L so as not to damage the wiring inside the Lid. Removing the Step L, the Regulator is appeared. (Photo 11.1c)

@ Pull off the 2 Connectors. (Photo 11.1c)

CONNECTOR (2)

PHOTO 1l.1¢

Page 75

Take out the 3 truss screws to remove Sash R (L type fitting). (Photo 11.1d)

TRUSS SCREW (3) M4 X 12,chrome plated

PHOTO 11.1 d

(©) Take out the 3 truss screws. (Photo 11.1e)

TRUSS SCREW (3),black

PHOTO Il. le

Page 76

Remove Step R slowly. Use care when removing the Step R so as not to damage the wiring inside the lid. (Photo 11.1f)

@ Pull out the 2 Connectors. (Photo 11.1g)

STEP R

CONNECTOR (2)

PHOTO 11. 1f PHOTO 11.1 g

Take out the 2 truss screws to remove the Bellows Bracket A on both sides ahead of the Ride. (Photo 11.1h)

TRUSS SCREW (2),black M5 X 12

PHOTO 11. 1h

Page 77

® Take out the 2 truss screws to

remove the Bellows Bracket Front. (Photo 11.1i)

ite

TRUSS SCREW (2),black; M4 X 12

PHOTO 11.1i

Page 78

11 - 2 GREASING AND RETIGHTENING THE BOLTS

Be sure to use the designated grease. Using undesignated grease can cause parts damage.

IMPORTANT! Once every 6 months, apply greasing to @ ~ ® mobile parts. Use Spray Grease (Part No. 090 - 0025). Apply Spray Greasing to the Rod End and Bearing from the Grease Nipple. At the same time, check to see if the nuts which secure @ ~ ) each bearing and Rod End are loosened. If loosened, retighten the nuts.

(il) “csc

FIG. 11.2 peat)

Page 79

@) CRANK PORTION © LOWER PART OF LINK & LOWER PART OF REAR CYLINDER

«

BEARING,

ROD END. ROD END of CYLINDER

S) FRONT CYLINDER PORTION

GEAR PORTION PHOTO 11.2

Page 80

11-3 ADJUSTMENT AND REPLACEMENT OF PITCH VOLUME

During game, in the cases where the vertical movements of the Ride is irregular or the Volume indicates abnormal values, Pitch Volume Gear mesh may be wrong, or Volume malfunctioning may be the cause. Make adjustments or replace as per the following procedure:

@tun the main switch of the AC Unit off. @ Remove the Rear Lid of the Mechanism Base, and close the Main Cock. ® Remove the Lid Left of the Mechanism Base. The Pitch Volume can be seen on the side of the lower front part of the Ride (FIG. 11. 3).

ADJUST GEAR V.R. SHAFT

V.R. BRACKET

M4 X 8, flat & spring washers 220-5373,5484

FIG. 11.3

O) Loosen the 2 screws which secure the V. R. Bracket to move the V. R. Bracket. ® Move the Volume Bracket to disengage gear mesh, turn the Volume Shaft in the manner so that the Volume Shaft cut portion faces 45 degrees lower left as shown.

  • Have the gears meshed and tighten the 2 screws to secure the Volume Bracket. @ When the Volume is malfunctioning, first disconnect the connectors connected to the Volume, take out the 2 screws which secure the Volume Bracket, and remove the Volume Bracket with the Volume as is attached.

Remove the gear from the Volume Shaft and replace the Volume.

Page 81

11 -4 REMOVE THE INCLINATION SENSOR

The Inclination Sensor detects the inclination of right and left of the Ride. Malfunctioning the Ride toward right-and-left direction can cause a failure of the Inclination Sensor. Replace the Sensor, which located in the bottom behind the Ride, in the following procedure.

® Tum the main switch of the AC Unit off.

@ Remove the Rear Lid, the Step L and the Step R (see 11 - 1).

® Tum the main switch of the AC Unit off @ Remove the Rear Lid, the Step L and the Step R (see 11 - 1) (6) Pull off the Inclination Senor

Connector.

Disconnect the connector.

PHOTO 11.4a

@ Take out the 2 screws and remove

the whole bank bracket of the Sensor.

M4 X 8,w/flat & spring washers PHOTO 11, 4b

Page 82

® Take out the 2 screws and remove

the Sensor from the bracket to replace it.

INCLINATION SENSOR 370-5130

SCREW (2) M3X8

PHOTO 11. 4c

© After the replacement, be sure to perform the Roll Volume Setting in the Test Mode (see 9-3 e).

Page 83
  • HANDLE MECHANISM

Before starting to work, ensure that the Power SW is OFF. Failure to observe this can cause electric shock or short circuit.

WARNING! Use care so as not to damage wirings. Damaged wiring can cause electric

shock or short circuit. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause electric shock hazard. Do not insert hand into the mechanism so as not to cause hand and fingers

pinched in. Failure to observe this can cause a serious injury such as a

fracture. When performing work such as parts replacement other than those specified in this manual, be sure to contact where you purchased the product from and confirm the work procedures and obtain precautions prior to performing work. Inappropriate parts replacement and/or installing with erroneous adjustment can cause an overload or the parts to come into contact, resulting in an electric shock, a short circuit, and a fire.

Be careful when handling the plastic made parts. Failure to observe this may cause injury due to damage or fragments resulting from damage.

CAUTION!

In the Test mode, if the variations in Volume (V. R.) values of the Handle Bar, etc. can not be set within the allowable range, Volume installation position (gear mesh) adjustment or Volume replacement is needed. Once every 3 months, be sure to apply greasing to gear mesh and spring portions.

12 - 1 ADJUSTING AND REPLACING THE THROTTLE V.R.

This work requires a Phillips TRUSS SCREW (3),black type screwdriver for M4 screws and a box nut screwdriver for M4 hexagon nut or a wrench.

Take out a total of 3 Truss

Screws to remove ACCEL. COVER B.

PHOTO 12. 1a |ACCEL. COVER B

Page 84

@ Take out a total of 4 Truss Screws to ACCEL. COVER A

remove ACCEL. COVER A.

TRUSS SCREW (4),

PHOTO 12. 1b

® Take out 2 Truss Screws to remove the VR Cover. P|

TRUSS SCREW (2)

PHOTO 12. le

O) Loosen the 2 Nuts which secure the Volume Bracket to move the Volume Bracket. (FIG. 12. 1).

VOLUME220-5373 or 220-5484 V.R. BRACKET

FIG. 12.1

Page 85

® Moving the Volume Bracket causes Adjust Gear mesh to be disengaged.

© Adjust gear mesh and tighten the 2 Nuts.

Grip the Throttle Lever and check to ensure that the V. R. value variations are within the rotatable range of the Volume Shaft.

After finishing adjustments, be sure to perform Throttle Volume setting on the Volume Setting screen in the Test mode (see 9 - 3e).

REPLACING THE THROTTLE VOLUME

@Tum the power off. @ Perform the above adjustment procedure ® ~ ©.

  • Disconnect the connector connected to the Throttle Volume. (PHOTO 12. | d)

THROTTLE VOLUME 220-5373,5484

CONNECTOR (1), BLACK 3P

PHOTO 12.1d

® Take out the 2 Nuts which secure the Volume Bracket, and remove the Volume Bracket with the Volume as is attached.

® Remove the Volume Gear from the Volume Shaft, and replace the Volume by removing from the Bracket.

© Afier the replacement, perform Volume Setting in the Test mode (see 9 - 3e).

Page 86

12-2 ADJUSTING OR REPLACING THE HANDLE V.R.

Adjust or replace the Handle Volume in the following procedure. This work requires a Phillips screwdriver for M5 screws and a short Phillips screwdriver for M4 screws.

®© Take out the 3 fixed truss screws

and remove the cover of one side so as not to put the power excessively.

TRUSS SCREW (3),black

PHOTO 12.2a

@ Removing the side cover, the Handle Volume is appeared. Perform this work using a short Phillips screwdriver.

PHOTO 12.2b

Page 87

® Loosen the 2 screws that secure the V.R. Bracket to move the V.R. Bracket. @) Move the V. R. Bracket to disengage the Adjust Gear mesh and move the V.R. shaft so that the cut part of the shaft may turn to the opposite side of the Adjuster Gear as shown.

® Engage the gear and tighten the 2 screws.

© Carefully turn the Handle Shaft to the left/right and ensure that the V.R. value variations are within the range of the Volume.

Mater finishing adjustments, be sure to perform the Handlebars Volume Setting in the Test Mode (see 9-3 e).

SCREW (2)M4 X 8,w/flat & spring washers V.R. SHAFT

ADJUST GEAR

V.R. BRACKET

FIG. 12.2

SCREW (2) V. R. REPLACEMENT MAX B,w/flat & spring washers _ =

ake out the 2 screws that secure the

Volume Bracket to remove the Volume Bracket.

@ Remove the Volume Gear from the

V.R. to replace the V.R.

HANDLE V.R. 220-5373,5484 PHOTO 12.2¢

@atter the replacement, be sure to perform the Handlebars Volume Setting in the Test Mode (see 9-3 e).

Page 88

12 - 3 GREASING

ig undesignated grease can cause parts

Once every 3 months, apply greasing to the following portions. For spray grease, use GREASE MATE (PART No. 090-0066).

Gear mesh portion

PHOTO 12.3 a

Torsion Spring portion

PHOTO 12.3 b

Page 89
  • COIN SELECTOR

HANDLING THE COIN JAM

If the coin is not rejected when the REJECT button is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

@ Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Never apply machine oil, etc. to the Coin Selector. After cleaning the Coin Selector, insert a regular coin in the normal working status and ensure that the Selector correctly functions.

The coin selector should be cleaned once every 3 months. a) When cleaning, follow the procedure below: f

@tum the power for the machine OFF. Open the @ Remove the coin selector from the coin chute door Open the gate and dust off by using a soft brush (made of wool, etc.)

coin chute door. @ Remove the coin selector from the coin chute door.

(made of wool, etc.).

©) Remove and clean smears by using a soft cloth

dipped in water or diluted chemical detergent and then squeezed dry. G) Remove the CRADLE. When removing the retaining ring (E ring), be very careful so as not to bend the rotary shaft.

(6) Remove stain from the rotary shaft and shaft @atier wiping off as per above, further apply a dry

receiving portions by wiping off with a soft cloth, ete.

cloth, etc. to cause the coin selector to dry completely. CRADLE

FIG. 13b

COIN INSERTION TEST

Once every month, when performing the Insert a coin while keeping the Reject But- Coin SW Test, simultaneously check the ton pressed ing: down and check following: if it is rejected.

[Does the Coin Meter count satisfactorily? COIN METER/ L1Does the coin drop into the Cashbox correctly? Ke [Is the coin rejected when inserted while keeping the Reject Button pressed down? FIG. 13.c

Page 90

a S

  • x S SSi1z22 2Ssass LSaaEesSs —sxze 3 ZERS ees a Bon a ogagava=zt =Z=S°5 SEED S255 eaan SNags = oc >

= Ss

S = = z=: wSa* wes 5a: Zot <ce¢ Oog aCe n° mss SS 4s 22s Fes OZ8 yss no mac

Page 91

www.seuser vice.com Tom Happ Ph: 847-593-6161 ext. 107 tom.happ@happcontrols.com Fx: 847-956-2091 Happ Controls, 106 Garlisch Drive, Elk Grove, IL 60007 Visit our website http://www.happcontrols.com 42-0641-00 il 42-0405-00 FOR §.25 COIN 42-0405-05 FOR $1.00 COIN 42-1044-00 $1.00 4 x .25 1 PLAY 42-0895-05 $1.00 PUSH TO REJECT

i $0.25 42-3079-00 $1.00 42-3113-00 @=— 43-0021-00

42-7087-00- 43.-01396-00—er" 42-6178-00

  • 42-8174-10 Guardian Hasp 30-2400-200

42-8177-00

Page 92

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON WAVERUNNER GP COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATOR(S):

FORWARD-MOST Mars 2000 series HOLE POSITION

**42-1155-00 MARS VALIDATOR $1, 2, 5 300 CAP

The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the cut-out plate. This one entry door can be ordered through Happ Controls or one of Happ Controls authorized distributors. The part number is 40-6000-10EX. The Mars stacker can be obtained through an autherized Mars distibutor.

Note: Your game may have either Happ Controls Coin Door Assembly or the Wells Gardner Coin Door Assembly (not shown).

**Happ part number

Security Locking Bar/Bracket Set Part No.# 999-0966

Modified Cash Box (For use when DBA installed) Part No. # 999-1106

Plastic Cash Box - Full Size Part No. # 999-1177

Page 93
  • PROJECTOR
CAUTION!

<

IMPORTANT! Since the Projector has been adjusted at the time of shipment, avoid making further adjustments without good reason.

The Projector is subject to color deviation due to Convergence deviation caused by the geomagnetism at the installation location and peripheral magnetic field. After the installation of machine, and before commencing operation, check for Convergence deviation and if deviated, make adjustments.

Projector adjustments are stored. Due to distortion or color deviation in the TEST mode, if an adjustment is necessary, use the Remote Control to make adjustments.

14 - 1 CLEANING THE SCREEN

CAUTION! Since the Projector screen is susceptible to damage, pay careful attention to its handling. When cleaning, refrain from using water or volatile chemicals.

When the screen surface becomes dirty with dust, etc., clean it by using a soft cloth such as gauze. When water, and volatile chemicals such as benzine, thinner, etc., spill on the screen surface, it may be subject to damage, therefore, do not use them. Also, since the surfaces are susceptible to damage, refrain from rubbing them with a hard material or using a duster.

FIG. 14.1

Page 94

14-2 ADJUSTMENT OF TOSHIBA PROJECTOR

SETTING THE INTERFACE

resulting in power off.

IMPORTANT! In this product, set to INPUT LEVEL: 0.7V and IMPEDANCE: 75Q. Failure to observe this can cause CRT membrane to burn or Shutdown device to function

The Projector's Connector Panel contains the Interface setting SW.

(e)

WINNER AC IN LAMP actoosz0v oe ca

[e) IMPEDANCE input LeveL

REMOTE CONTROL BUTTONS

When adjusting the Projector, direct the Remote Control's light emitting portion towards the Projector Screen.

MODE (mode selection) TEST (adjust/normal shift) ol R.G.B. (color selection) <—#}

POSITION (to select the position)

ADJUST (adjustment e £4 REMOTE CONTROL LIGHT EMITTING PORTION

WRITING (storing the data) P (automatic color matching)

SET (to decide the selection)

7 PIC - ADJ (item selection)

RESET

SELECT (pattern selection) setecr|

Page 95

AUTOMATIC COLOR MATCHING

The Projector may be subject to color deviations affected by earth magnetism, the building steel frames, etc. When the Projector is initially installed or the Projector’s installation position is changed, have the color matching performed automatically.

® Keep pressing the P button (red) for approximately 3 seconds to have

the ensuing movements performed automatically.

> @ @. 3) + an Vv & y. fy The Projector will shift to the color deviation correction mode from the game mode, with the green cross pattern appearing on the screen.

The cross pattern moves up/down and right/ left to start the movement of searching the correct screen position and inclination.

When the green cross pattern movements are finished, similar detection is performed sequentially in order of red and then blue cross movements. After detecting by green, red and blue cross movements, the game mode returns with the color deviation status being corrected.

@ Although very rarely, the TRY AGAIN error display in red may appear. At this time, press the P button (red) for approximately 3 seconds. Even after the above operation is repeated, if the error condition still exists, then the display shifts to PLEASE ADJ. In this case, the auto color matching function can not be used. Contact the place of contact herein stated or where the product was purchased from.

@ = Ifthe automatic color matching indicates an error, color matching can manually be performed. Refer to CONVERGENCE ADJUSTMENT (manual color matching).

Page 96

ADJUSTING THE ON-SCREEN CONTRAST

Although the on-screen picture quality has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary. Changing the CONTRAST causes the light and shade of the on-screen images to be changed. A PIC-ADJ

Herein, /\ procedure is skipped. Geeta)

SET

«ADJUST

WRITING ® Press either 4, or W PIC - ADJ button.

The on-screen menu will have one item in purple and 6 items in white. CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT

@ Choose CONTRAST by using either Q or W

PIC - ADJ button.

Have CONTRAST dis- CONTRA SIS played in purple. Since H.POSI CONTRAST is selected

ace initially, no particular

V.SIZE operation is required in this EXIT case.

® Press the SET button (to decide selection).

When the selection of the CONTRAST adjustment mode is decided, the adjustment data scale bar appears on the screen. CONTRAST 230 Breese Besse aa

® Make adjustment by using either < or > ADJUST button.

As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen contrast status.

© Press the WRITING button (for storing and finish).

The WRITING display appears and the adjustment data is stored.

WRITING

@ When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure e) and press the SET button.

@ To continue adjusting other menu items, repeat procedure @ = ® :

@ Unless the adjustment data is stored, the data in the adjusted-status will be erased at the time the power is tumed off and the pre-adjustment status will remain when the power is turned on next time.

Page 97

ADJUSTING THE SCREEN BRIGHTNESS

Although the on-screen picture quality has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustment may be necessary. Changing the BRIGHTNESS causes the brightness of the on-screen images of black portions to be changed.

PIC-ADJ CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE, EXIT

  • ADJ button.

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT © A ® Press either 4. or W PIC - ADJ button. The on-screen menu will have one item in purple and 6 items in white.

@) Choose BRIGHTNESS by using either 4 or W PIC

Have the BRIGHTNESS displayed in purple.

SET ® Press the SET button (to decide selection).

«ADJUST BRIGHTNESS 128 Beene Bee ee oe When the selection of the BRIGHTNESS adjustment mode is decided, the adjustment data scale bar appears on the screen.

Make adjustment by using either <q or | ADJUST button.

As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen brightness status.

WAITING ® Press the WRITING button (for storing and finish).

WRITING The WRITING display appears and the adjustment data is stored.

@ When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure (2) and press the SET button. @ = To continue adjusting other menu items, repeat procedure(2) ~ @® @ Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will remain when the power is tured on next time.

Page 98

ADJUSTING THE ON-SCREEN DISPLAY POSITION

Although the on-screen display position (H. POSI, V. POST) has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustments may be necessary.

/\ ® Press either 4 or W PIC - ADJ button.

PIC-ADJ. CONTRAST The on-screen menu will have

BRIGHTNESS one item in purple and 6 items in H.POSI white. V.POSI H.SIZE V.SIZE EXIT

PIC ADJ button.

A @ Choose H. POSI or V. POSI by using either A or Vv

FCA J Have the H. POSI or V. POSI

V PONTE Sa displayed in purple. The Figure

H.POSI shows the status in which H. PEs! POSL is selected. H.SIZE V.SIZE EXIT

5 ® Press the SET button (to decide selection). ET When the selection of the H. POSI or V. POST is decided, the adjustment data scale bar appears on the screen.

® Make adjustment by using either < or > ADJUST ADJUST button.

o © As the Cursor is moved, the

adjustment data value changes. When making adjustments Make adjustment so as to obtain in vertical directions, also the desired on-screen position . ° status. use either < or ADJUST button.

WRITING ® Press the WRITING button (for storing and finish). The WRITING display appears and the adjustment data is stored.

WRITING

@ When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure (2) and press the SET button. @ To continue adjusting other menu items, repeat procedure(2) ~ @ Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is tured off and the pre-adjustment status will remain when the power is turned on next time.

Page 99

ADJUSTING THE SCREEN SIZE

Although the on-screen size (H. SIZE, V. SIZE) has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustments may be necessary.

@| & @ @/@|@ @e

< PIC-ADJ

SET

OO

When making adjustments in vertical directions, also use either < or > button.

WRITING

the SET button. ® Press either 4y or W PIC - ADJ button.

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT The on-screen menu will have one item in purple and 6 items in white.

@ Choose H. SIZE or V. PIC - ADJ button.

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE, EXIT . SIZE by using either & or W

Have the H. SIZE or V. SIZE displayed in purple. The Figure shows the status in which H. SIZE is selected.

® Press the SET button

(to decide selection).

When the selection of the H. SIZE or V. SIZE adjustment mode is decided, the adjustment data scale bar appears on the screen.

® Make adjustment by using either < or | ADJUST button.

As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen position status.

© Press the WRITING button (for storing and finish).

WRITING The WRITING display appears. and the adjustment data is stored.

To continue adjusting other menu items, repeat procedure(2) ~ ® Unless the adjustment data is stored, the data in the adjusted si When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure(2) and press

tatus will be erased at the time the power is turned off and the pre-adjustment status will remain when the power is tured on next time.

www.seuser vice.com

Page 100

CONVERGENCE ADJUSTMENT (manual color matching)

CONVERGENCE ADJUSTMENT (Line Convergence Adjustment in particular)

CAUTION! for adjusting screen size changes. Ay To avoid circuitry malfunctioning due to electrical load increase, never utilize

There is no means to restore the Convergence Adjustment data once stored, to its original state. To avoid changing the screen size by erroneously using convergence adjustment, do not perform the green Line Convergence Adjustment. As such, be sure to perform the adjustment work from this page onward by the Technical staff and the location's Maintenance Personnel who are well versed in such adjustment work. In the Static Convergence Adjustments, if satisfactory adjustments can not be performed, do not make another convergence adjustments inadvertently. Contact the office herein stated or where the product was purchased from.

To avoid making the adjustment work ineffective, do not press the RESET button during adjustment.

IMPORTANT! To discontinue adjustment work, keep pressing the TEST button for

approximately 3 seconds at the stage before storing the adjustment data by pressing the WRITING button. Should the screen be abnormally disturbed by noise due to static electricity, etc., turn the power off without storing the adjustment data. Pressing the & or W PIC - ADJ button in the Convergence Adjustment mode status will display the Adjustment Menu shown right. Do not utilize this ADJUST Adjustment Menu as this is the one applied at the factory. ae : SUB V' Adjusting this menu causes the SUB Hi Customer's adjustment range to be SUB BRIGHT

deviated. EXIT

Should the menu shown right be displayed by mistake, first choose EXIT by using either & or W PIC - ADJ button and then press the SET button. Adjustment menu used in the factory.

Page 101

STATIC CONVERGENCE ADJUSTMENT

In the static convergence adjustment, each of red and blue images is comprehensively moved to and superimposed on the green color. If automatic color matching function is not sufficiently satisfactory, perform this adjustment. Be sure to perform automatic color matching before starting the above adjustment.

® Keep pressing the TEST button for

approximately 3 seconds. The screen will change to ADJUST mode from the Game mode to cause the green test pattern to be displayed on the screen. —ADIUS} MODE—

2) Press the R button to have the red adjustment

mode. The red test pattern is added to the display. The frame color turns red and this signifies the red adjustment mode.

® Make adjustment by using the & W < > When either of(2) ~ 4) COLOR ADJUST buttons. SELECT buttons (R, B) is pressed, if the aa MODE Make adjustment so as to have color desired to be adjusted disappears, red superimposed on green. press that particular button again. For When red is superimposed on : green, the color becomes example, if the red color needs to be yellow.

adjusted again at the stage of @. the R

button need to be pressed twice.

@® Press the B button to have the blue adjustment

mode.

Similarly as in the case of red, adjust the blue color. When green, red, and blue are superimposed, the color becomes white. —AbIUgF MODE—

  • Press the WRITING button (for storing and finish). aoe | The WRITING display appears and the adjustment data is stored. After the data is stored, the Game mode returns. WRITING
Page 102

POINT CONVERGENCE ADJUSTMENT

In the POINT CONVERGENCE adjustment, each of red, green and blue images is partially moved for color matching. The adjustment may be necessary when the Game Board is replaced or changed, or screen size is changed. Be sure to perform automatic color matching before starting

the adjustment. ® Keep pressing the TEST button for

approximately 3 seconds.

ADIOS The screen changes to ADJUST mode from the Game mode and displays the green test pattern.

@ Press the MODE button twice to have the POINT

ADJUSTMENT mode. Note 1

ian = The crosshatch test pattern appears

MARKER and the MARKER indicating the

adjustment point is displayed.

@)using either R or B button, select the desired color

to be adjusted. Note 2 By using the G button, the green color can also be selected.

= = The selected color is displayed by superimposing on green. The MARKER will be in the color selected.

@® By using he A W <q > ADJUST buttons,

Note 1 When the MODE button is repeatedly move the MARKER to the position to be adjusted.

pressed, the adjustment modes will ct ct The MARKER moves in the

circulate as follows: Poe FEeFey direction of the button's arrow. However, the movable point is STATIC ADJUSTMENT MODE pred? iermined,

LINE ADJUSTMENT MODE © Make adjustment by using the A W <q p> ADJUST buttons. POINT ADJUSTMENT MODE Although the direct vicinity of the MARKER's center moves most . 7 + conspicuously, make adjustment

Note 2 When either of the COLOR SELECT by paying attention to the periphbuttons (R, B) is pressed, if the desired ery area also. Shown left is the color to be adjusted disappears, press magnified MARKER periphery. that particular button again. © Press the SELECT button as necessary to superimpose Game Board images. Note 3
Note 3 By repeatedly pressing the SELECT supermne es ae button, only the Projector’s TEST . . SSeS Se Ee sea! the periphery of the screen, adjustpattern screen and the screen ments can be made by pressing the superimposing the Game Board Test SELECT button to superimpose the pattern can be alternately displayed. test pattern and the Game Board's CRT test screen. If the test pattern is not displayed in

@ Press the WRITING button (for storing and finish). et tee WRITING is displayed and the adjustment data is stored. After the data is stored, the Game Board screen returns.

Page 103

LINE CONVERGENCE ADJUSTMENT

Note 1
Note 2 In the LINE CONVERGENCE ADJUSTMENT, the adjustment point of the column line (vertical) or row line (horizontal) is comprehensively moved for color matching. It is convenient to utilize this adjustment when the color of the column line or row line is uniformly deviated.

® Keep pressing the TEST button for approximately

©

DO NOT PUSH. 3 seconds.

—ADIUSp MODE—

) Press the MODE The screen changes to ADJUST mode from the Game Board mode and displays the green test pattern.

button once to have the POINT ADJUSTMENT mode. Note 1

MARKER |

When the MODE button is repeatedly pressed, the adjustment modes will circulate as follows:

STATIC ADJUSTMENT MODE

LINE ADJUSTMENT MODE

POINT ADJUSTMENT MODE The crosshatch test pattern appears and the vertically long MARKER. is shown.

® Using either R or B button, select the desired color to

be adjusted. Note 2 Although the green color can also be selected by using the G button, to avoid the screen size change adjustment, do not choose green.

zi

move the MARK.

When either of the COLOR SELECT

buttons (R, B) is pressed, if the desired color to be adjusted disappears, press that particular button again.

at Make adjustme: The selected color is displayed by superimposing on green. The MARKER will be in the color selected.

V <P position buttons, ER to the position to be adjusted. Use the <q p> buttons to select the column line, and the MARKER, moves in the right/left direction. However, the movable range is predetermined.

Use the A W buttons to select the row line and the MARKER moves in the up/down direction. However, the movable range is predetermined.

t by using the A vV < > ADJUST buttons. The selected column line or row line (shown left is the column line) can be moved in the desired up/ down or right/left directions as applicable.

Press the WRITING button (for storing and finish). WRITING is displayed and the adjustment data is stored. After the data is stored, the Game Board screen returns.

Page 104
  • REPLACEMENT OF FLUORESCENT LAMP

When performing the work, be sure to turn power off. Working with power on can cause an electric shock or short circuit accident. The Fluorescent Lamp, when it gets hot, can cause burns. Be very careful when replacing the Fluorescent Lamp.

To perform work safely and securely, be sure to prepare a step which is ina secure and stable condition. Performing work without using the step can

CAUTION! cause violent falling down accidents. Be careful when handling the plastic made parts. Failure to observe this may cause injury due to damage or fragments resulting from damage.

® Remove the 3 screws which secure the Holder on the upper part of Billboard.

@ Pull out the Holder to the upper side of the Billboard, and replace the fluorescent lamp (32W).

TRUSS HEAD SCREW (3) M4 X 8, black

BILLBOARD BILLBOARD HOLDER

FLUORESCENT LAMP 32W: 390-5251-32-01 GLOW LAMP: 390-5638-5P.

FIG. 15a

When performing work, prepare a step.

FIG. 15b

Page 105
  • PERIODIC INSPECTION TABLE

The Air Compressor employed in this product drives the Ride during game. The items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe business operation.

@ Be sure to check once a year to see if Power Cords are damaged, the plug is

securely inserted, dust is accumulated between the Socket Outlet and the

WARNING! Power Plug, etc. Using the product with dust as is accumulated can cause a fire or electric shock. Periodically once a year, request the place of contact herein stated or the Distributor, etc. where the product was purchased from, as regards the interior cleaning. Using the product with dust as is accumulated in the interior

without cleaning can cause a fire or accident. Note that cleaning the interior

parts can be performed on a pay-basis.

TABLE 16

ITEMS DESCRIPTION PERIOD REFERENCE

CABINETCheck LEG ADJUSTER adjustments.Daily3
AIR DRIVEDewatering of FILTER.Weekly10-2
puSTEMDewatering from AIR TANK.Weekly10-3
Check Regulator's set pressure.Bi-monthly10-4
Check AIR CLEANER.Bi-monthly10-5
MECHANISMCheck SAFETY SENSOR.Daily3
Check BELLOWS.Daily3
Greasing for each of Pillow Block and Rod End.Biannually11-2
Tightening the Bolts further.Biannually11-
HANDLE MECHACheck VOLUME VALUE.Monthly9
Greasing of GEAR and bearing.Tri-monthly12
COIN CHUTECheck COIN SWes.Monthly9
TOWERCoin insertion test.Monthly13
Cleaning of COIN SELECTOR.Tri-monthly13
POWER SUPPLY PLUGInspection and cleaningAnnuallySee above.

INTERIOR Cleaning

CABINETCleaningAs necessary.

CLEANING THE CABINET SURFACES

When the cabinet surfaces are badly soiled, remove stains with a soft cloth dipped in water or diluted (with water) chemical detergent and squeezed dry. To avoid damaging surface finish, do not use such solvents as thinner, benzine, etc. other than ethyl alcohol, or abrasives, bleaching agent and chemical dustcloth.

Page 106
  • TROUBLESHOOTING

17-1 TROUBLESHOOTING

WARNING! @ In order to prevent electric shock and short circuit, be sure to turn power off before performing work. Be careful so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. After removing the cause of the functioning of the Circuit Protector, reinstate

the Circuit Protector. Depending on the cause of the functioning, using the

Circuit Protector as is without removing the cause can cause generation of heat and fire hazard.

In case a problem occurs, first check wiring connector connections.

TABLE 17a

PROBLEMS CAUSE COUNTERMEASURES

When the main SW is turned ON, the machine is not activated. The power is not ON. Firmly insert the plug into the outlet.

Incorrect power source/voltage. Make sure that the power supply/voltage are correct.

The CIRCUIT PROTECTOR functioned due to momentary overcurrent. After eliminating the cause of overload, have the Circuit Protector of the AC Unit restored. (See Section 6 and Next page)

The fuse of the connect board was blown out due to momentary overcurrent. After eliminating the cause of overload, replace the specified rating fuse (514-5036-7000, FUSE 6.4.0 X 30 7000mA 125V). (PHOTO 17. 1 b)

The color on the PTV screen is not correct. Screen adjustment is not appropriate. Make adjustment appropriately, (See Section 14)

PTV screen has a color deviation. Affected by the periphery, such as other machines, location building's steel frames, etc. Make convergence adjustments. (See Section 14)

Change installation direction/ position.

Move the other machines which cause the problem.

No PTV screen image. Connector connection fault. Check connector connection between the PTV and Cabinet. (See Section 6)

Sound is not emitted. Sound volume adjustment is not correct. Adjust the SWITCH UNIT's sound adjustment volume control. (See 9 - 1)

Malfunctioning BD. and Amp. Perform SOUND TEST. (NAOMI Service Manual)

During game play, the Compressor does not operate. Circuit Protector functioned due to momentary overload. After eliminating the cause of overload, have the power supply Circuit Protector restored. (PHOTO 17. 1 b)

During game, the Ride does not operate. Saftety Sensor functioned. Remove the foreign article.

Air Tank Cock is closed. Open the Cock. (See 11-1)

Preset pressure is incorrect. Make pressure adjustment, (See 10-4)

Air leakage. Check the Air Drive System.

Communication fault between the Main BD and the I/O BD. Check in the wiring test. (See 9-3g)

o7 www.seuser vice.com

Page 107

TABLE 17 b

PROBLEMS CAUSE COUNTERMEASURES

During game, the Ride does not turn when the Handlebars are turned. Deviation of Handle Volume. Adjust the Volume value in the test mode. (See 9-3e)

Malfunctioning of Handle Volume. Replace the Volume. (See 12-2)

When gripping the Throttle Lever, the Ride does not advance. Deviation of Throttle Volume. Adjust Volume values in the Test mode. (See 9-3e)

Malfunctioning of Throttle Volume. Replace the Volume. (See 12-1)

Vertical movements of the

Ride during game is weak and irregular. Initial setting is wrong. Turn power off and then turn it back on again to perform initial setting movement. (See 6 Section 6)

Malfunctioning of Pitch Volume. Replace Volume. (See 11-3)

Preset pressure is incorrect. Make pressure adjustment, (See 10-4)

Air leakage. Check the Air Drive System.

Communication fault between the V/O BD and Drive BD. Check in the wiring test. (See 9-32)

Air Damper adjustment fault.

Air Damper adjustment. (See the end of this Section)

Lefv’right movements of the

Ride is weak and irregular. Deviation of Roll Volume. Adjust Volume values in the Test mode. (See 9-3e)

Preset pressure is incorrect. Make pressure adjustment, (See 10-4)

Air leakage. Check the Air Drive System.

Communication fault between I/O BD and Drive BD. Check in the wiring test. (See 9-3g)

Malfanctioning of Inclination

Sensor. Replace the Inclination Sensor. (See 11-4)

Communication play not possible, Communication cable connection is incorrect. Connect the communication cables correctly. (See 20-2)

Communication settings are wrong. Corrs tthe settings, (See 20-3)

Fluorescent lamp doesn't light up. Connector connection fault. Check connector connections between the Billboard and PTV. (See Section 6)

Fluorescent lamp need replacement. Replace the fluorescent lamp. (See Section 15)

CIRCUIT PROTECTOR en CIRCUIT PROTECTOR

Functions due to the activation of bimetal. To restore the function, wait for approximately one minute or longer until the bimetal cools off. (Press the Button.)

Page 108

CIRCUIT PROTECTOR and FUSE REPLACEMENT

WARNING!

FUSE7 514-5036-7000}

CIRCUIT PROTECTOR In case fuse replacements other than those stated in this manual are necessary, contact where you purchased the product from for inquiries regarding this matter. Fuse replacements other than those specified can cause accidents and are strictly forbidden.

In order to prevent an electric shock, be sure to turn power off and unplug

from the socket outlet before performing work by touching the internal parts of the product. Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit accidents. Be sure to use fuses meeting specified rating. Using fuses exceeding the specified rating can cause fire and electric shock accidents. After eliminating the cause of the blowing of fuse, replace the fuse.

Depending on the cause of fuse blowing, continued use with the fuse as is

lown can cause generation of heat and fire hazard.

Remove the 2 truss screws and dismount the lower lid from the front cabinet. The fuse and the circuit protector for the air drive are installed on the ASSY PWR SPLY unit inside the front cabinet.

PHOTO 17. 1a

TRUSS SCREW, black, M4 X 25

LOWER LID,

PHOTO 17. 1b

Page 109

AIR DAMPER ADJUSTMENT

In this machine, the Cylinders are equipped with air dampers to soften the impact created by the Ride movements. If the Cylinder's amplitude of vibration or the impact is excessive, adjust the air dampers in the following procedure.

After turning the power off, close the Main Cock to start working. Starting work without closing the Main Clock can cause serious injury.

WARNING!

Make adjustments as specified. Adjusting in the manner not specified can cause

malfunctioning and parts damage.

IMPORTANT!

® Turn off power and turn the Circuit Protector inside the Front Cabinet OFF (see 10-1). @ Remove the Rear Lid from the Mechanism Base and close the Main Cock (see 11-1). ® Remove the Step R (see 11-1). @® Loosen the Lock Nut of the Rear Cylinder's Adjuster fully to the bottom of the Adjuster. ® Loosen the A, B, C, and D Adjusters by 90 degrees from the fully tightened point. © Tighten the lock nut so the adjuster will not rotate. @ After making adjustments, play the game and check to see that the adjustments made are correct.

ADJUSTER A Loosen by 90 degrees. ADJUSTER B Loosen Tighten ‘Loosen by «7 90 degrees. ~ *®) After tightening the REAR’ ADJUSTER C Adjuster fully, CYLINDER t ‘Loosen by reverse it to the 90 degrees. specified position.

ADJUSTER d

LOCK NUT ADJUSTER D

> H Loosen by 90 degrees.

After reversing the H adjuster to the specified position, secure the Adjuster with LOCK NUT.

FIG. 17 .

Page 110

17 - 2 ERROR MESSAGE

A

WARNING!

@ = This work should be performed by the Location's Maintenance Man or

Serviceman. Performing work by non-technical personnel can cause accidents. Should any errors other than listed by this manual or by NAOMI Service Manual occur, contact where the product was purchased from or an office described in this manual. Failing to comply with this instruction can cause accidents.

This product displays the error on the screen if the faulty is detected. If an error is displayed, be sure to take action against it according to the appropriate cause and countermeasures listed below. It may be displayed the error other than listed by this manual or by NAOMI Service Manual. In that case, contact where the product was purchased from or an office described in this manual without operating it selfishly.

ODISPLAYO NETWORK ERROR: NO MASTER SITE OCAUSEO No MASTER setting in Communication Mode. [TOCOUNTERMEASURESO Perform the Communication Mode setting in the Game Assignments. Set one of the machines to MASTER and all others to SLAVE. (9-3 d) (20-3)

DISPLAYO NETWORK ERROR: DUPLICATE MASTER SITE OCAUSEO MASTER setting is duplicated in Communication Mode. CI COUNTERMEASURESO Perform the Communication Mode setting in the Game Assignments. Set one of the machines to MASTER and all others to SLAVE.

CIDISPLAYO NETWORK ERROR: NO SLAVE SITE

OCAUSEO No SLAVE setting in Communication Mode. CX COUNTERMEASURESO Perform the Communication Mode setting in the Game Assignments. Set one of the machines to MASTER and all others to SLAVE. (9-3 d) (20-3)

ODISPLAYO NETWORK ERROR: TOO MANY NODES SITE OOCAUSEO Too many machines are connected. C0 COUNTERMEASURES O Up to 4 machines can be connected to allow to enjoy communication play.

ODISPLAYO NETWORK ERROR: DUPLICATE CABINET ID

OCAUSEO The number of Cabinet ID is duplicated in Communication Mode. DO COUNTERMEASURES O Change the number of Cabinet ID for every seat in the Game Assignments. (9-3 d) (20-3)

ODISPLAYO DRIVE BD ERROR: E2H

O CAUSE O The Ride is not centering with the right value. OO COUNTERMEASURESO Ensure that the Ride is slanted or the connector of ASSY Wire Tube is connected securely. (Section 6)

Page 111

XO DISPLAY O DRIVE BD ERROR: E3H O CAUSE O The Down Limit Switch is not changed to ON. CO COUNTERMEASURES O Ensure that the Ride is down fully or the connector of ASSY Wire Tube is connected securely. (Section 6)

DODISPLAY O DRIVE BD ERROR: E4H OOCAUSE O The Up Limit Switch is not changed to ON. CX COUNTERMEASURES O Ensure that the Ride is up fully or the connector of ASSY Wire Tube is connected securely. (Section 6)

DISPLAY O DRIVE BD ERROR: E7H OCAUSEO The pressure of the air tank is not sufficient. LI COUNTERMEASURES O Be sure of the compressor's function or the air leakage.

DISPLAY O NO DRIVE BOARD OCAUSEO The connection of the Drive Board is not correct. O COUNTERMEASURES O Ensure that the connectors inside of the front cabinet are connected securely.

Page 112
  • GAME BOARD

In order to prevent electric shock and short circuit hazards, be sure to turn power off before performing work.

WARNING! Be careful so as not to damage wirings. Damaged wiring can cause fire,

electric shock and short circuit hazards. Do not expose the Game BD, etc. without a good reason. Failure to observe this can cause electric shock hazard or malfunctioning. To perform work safely and securely, be sure to use 2 or more workers.

The electronic parts on the IC Board could be damaged due to human body's static electricity. Before performing IC Board related work, be sure to discharge

CAUTION! physically accumulated statics by touching grounded metallic surfaces, etc.

Case when requesting for the replacement or repair. Transporting the Game Board in an undesignated status for replacement/repair is unacceptable.

IMPORTANT! In this manual, how to remove the Game Board is explained for convenience. However, this work should be performed by SEGA SERVICEMAN. Gr00 Put the Game Board in the Carton Box (an accessory) together with the Shield

18 - 1 REMOVING THE GAME BOARD

The Game Board is installed inside the Front Cabinet.

® Tum the main switch of the AC Unit off.

® Tum the main switch of the AC Unit off @) Push aside the Rear Cabinet (6) Take out the 2 truss screws that

to keep a workspace.

secure the Service Lid on the upper front part of the Front Cabinet.

SERVICE LID

TRUSS SCREW (2),black M4 X 16

PHOTO 18. 1a

Page 113

@ Unlock the Service Lid and lift it up a little, and

take out the nut securing the earth wire carefully to remove the Service Lid.

Unlock

PHOTO 18. 1b

© Disconnect all the connectors of the NAOMI Game Board installed inside the Cabinet.

@©Take out the 4 screws securing the Game Board to remove it. Taking out the screws, the Game Board will fall down. Be sure to take out the screws supporting the Board firmly.

SCREW (4) M4 X 16,w/flat &

isconnect the connector.

PHOTO 18.1¢

Page 114

18 - 2 COMPOSITION OF GAME BOARD

Ensure that the DIP SW setting is performed as designated. Failure to observe this may cause functioning not suitable for the actual operation, or malfunctioning.

IMPORTANT!

ASSY CASE NAO WRG USA (840-0064D-01) : USA ASSY CASE NAO WRG EXP (840-0064D-02) : OTHERS ASSY CASE NAO WRG KOR (840-0064D-03) : KOREA ASSY CASE NAO WRG AUS (840-0064D-04) : AUSTRALIA

ROM CASE NAO WRG SCREW (4) 840-0064C | ax MB X 50,chrome plated

ASSY CASE NAO COMMUNICATION BD $40-0001E \ Ua ~

ay) / DIP Sw/

ASSY CASE NAOMI MAIN BD USA:840-0001A-01 ASSY CASE NAOMI MAIN BD EXP:840-0001A-02 ASSY CASE NAOMI MAIN BD KOR:840-0001A-03 \ ASSY CASE NAOMI MAIN BD AUS:840-0001A-04

FIG. 18.2a

Gn this product, set all of the DIP SWes to OFF.

[e) PEE

FIG. 18.2b

Page 115
  • DESIGN RELATED PARTS

For the Warning Display stickers, refer to Section 1.

STICKER COMPRESSOR

Page 116

WOI-aIIAAASNISMMM LOI q6l Old ¥ SGIS IST NINITIS £c0E-248 Y TOW waxoIES N-T00E-DuM ¥ GUND FOIS HINOTIS I-6E0E-D4N Y NOLITIONE NINITES S-T00E-948 IS) v aur sous wexoras = ‘HOSHORS aNOTES pbs icon 2 DUNT WieMeE wares a 100e Stat @-P00E-94 Y INIT SOIS ¥ENOTES 0-T006-9u8 7 GOS aSVE WINITES 2208-244 7 [ON USNOTES yuvHS HaNOTES W-TO0E-DU T-1006-98M EJ 7 GWenD 01S YaXOTES B-8E0E-DUN 7 NOLITIOUT YINDTIS Y= T00E-DUN 7 aout voenws wavoris NTN ‘0-100£-D4s ——_ T QNIT GOrS NINOTIS a-T00E-Du

THD WOES YINOTES 2-£008-24M 7 NIT INOUE YEXOTES @-£006-94 T YOSNOES WINITIS @-£006-944 OUUHOTN YEMDTIS F-C00E-DUN ONTOVE HENOTIS -200E-DUN OWN HINOTIS 2-C00E-DU

TUNOTIGO DUM YTOMN YIXITES £000-2u AT RN YOCUTTIIO YIXITES mm 7-S098-D4 YGAOD SSOT UINITIS @-9E0E-DUM

Page 117

[<") RUNABOUT".

WRG-0511 WRG-1008 my-197) qoen3T4 WRG-1003 WRE-OS12 STICKER PTY SIDE STICKER FRONT CARI CMPSR BX f CMPSR BX CKER FRONT CARH R STICKER PTV SID@

FIG. 19¢

Page 118
  • COMMUNICATION PLAY

For this game, up to 4 machines can be connected to allow up to 4 players to play simultaneously. In this instance, connecting the communication cable and setting for the communication play are required.

20 - 1 INSTALLATION PRECAUTIONS

WARNING!
CAUTION!

S

IMPORTANT! Before starting to work, ensure that the Power SW is OFF. Failure to observe is can cause electric shock or short circuit. Use care so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause electric shock hazard. When linking a number of machines, be sure to supply sufficient power for the corresponding number of machines. Be sure to secure per machine current as stated in this manual. Failure to observe this can cause a fire and an ectric shock accident. Due to the length of the communication cable, the distance in between the machines is limited. However, to avoid accidents, be sure to secure space in excess of 70 cm between the machines. In order to avoid personal injury, when separating the machine into each Cabinet, pay attention so as not to cause the PTV to fall down. To perform work safely and avoid serious accident such as the cabinet's falling down, do not perform work in places where step-like grade differences, a ditch, or slope exist.

To perform work safely, be sure to secure the space corresponding to number of machines to be linked. Failure to observe this can cause accident.

The optic fiber cable is used for the communication linkage. Excessive bending may damage the communication cable. Be very careful in this regard.

Since 2 or more machines are to be linked, sufficient power corresponding to the number of machines used need to be supplied. Note that as a standard, the per machine capacity should be 15A for the 100 ~ 120V area, and 8A for the 220 ~ 240V area.

Page 119

DISTANCE BETWEEN MACHINES 70cm

Be sure to secure space in excess of 70cm between machines.

FIG. 20. 1

20 - 2 CONNECTING THE COMMUNICATION CABLE

To enable the game machines to serve in a communication play, you must interconnect their game boards with the communication cables (optical fiber cables). For this wiring, prepare the parts described in Table Sc of Section 5 and a short Phillips. screwdriver for M4 screws.

@tum off power and disconnect the plug. Disconnect the power cord so as not to damage it. @peferring to Section 7, uncouple and align the machines keeping the workspace in front of the Front Cabinet.

®Remove the Service Lid on the upper front part of the Front Cabinet (see 18-1). O) Take out the 2 truss screws and remove the Lower Lid in front of the Front Cabinet.

TRUSS SCREW (4),black M4 X 16 S

© ake out the 4 truss screws and

remove the Side Lid on the side of the Front Cabinet. In this instance, remove the Side Lid that lets the communication cable pass. Depending on the number and

arrangement of the interconnected

game machines, you may remove either or both of the two Side Lids.

SIDE LID

PHOTO 20. 2a

Page 120

© Insert the communication cable

into the assembled flex tube. Depending on the number of the interconnected game machines, the method of the interconnection varies.

PHOTO 20. 2b

@ Connect the communication cable to each game

board. Pass the communication cable through the round hole on the side of the Front Cabinet and connect to the game board connectors. A connecting method varies depending on the number of the interconnected game machines (see Fig. 20.2b). Always connect the red connector to RX and the black connector to TX, and thereby make a loop of the communication cable.

Connect the communication cable.

PHOTO 20. 2¢

Page 121

FIBER PLATE

Fix the Fiber Plate on the side of the Front Cabinet using the 4 truss screws that secured the Side Lid previously.

TRUSS SCREW (4),black M4 X 16

PHOTO 20.2d

TRUSS SCREW (2),black M4X16 NAOMIBD

COMMUNICATION CABLE

Unlock

SERVICE LID

FLEX TUBE

TRUSS SCREW (2),black M4 X25

TRUSS SCREW (4),black M4 X 16

FIG. 20.2 a

Page 122

2P LINK 3P LINK

||||1|H
—|\—}||
a2I|a2a2\

"I be - Lar _—

L CABINET ID 1 r CABINET [D0 2 x CABINET ID 1 i r r I CABINET [D 2 CABINET [D 3

4P LINK

ia: ae 1

CABINET [D 1

©) Install the Service Lid on the Front Cabinet and lock it. CABINET [D 2 CABINET [D 3 I L CABINET ID 4

FIG. 20. 2b Connecting method of the communication cable

( Arrange the interconnected game machines. Keep a space between the game machines as wide as possible.

@ Make the adjusters of all the game machines come into contact with the floor

(see Section 6 3 ).

(connect the power cords and the earth wires (see Section 6 5 ).

(connect the power cords and the earth wires (see Section 6 5 ) @®pat the number stickers on both

sides of the Ride. Facing the PTV screens, put the stickers '1', '2', '3', '4' from left to right.

FIG. 20.2 ¢

Page 123

20 - 3 SETTING FOR COMMUNICATION PLAY

Change the game setting for each seat in manner so as to meet communication play. If the setting is not correct, communication play cannot be played.

SETTING FOR COMMUNICATION PLAY @Otum the linked machines’ power on. @ Cause all of the machines to enter the test mode (see Section 9). @ Select the GAME ASSIGNMENTS (see 9-3 d).

GAME ASSIGNMENTS

If it is set to SLAVE, GAME DIFFICULTY NORMAL GAME DIFFICULTY and COMMUNICATION MODE NO LINK ~

HANDICAP ON HANDICAP are

CABINET ID 1 disappeared on the screen.

> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 20.3 GAME ASSIGNMENTS Screen

@) Perform the COMMUNICATION MODE setting in the GAME ASSIGNMENTS screen. Set

one of the machines to MASTER and all others to SLAVE.

  • Perform the CABINET ID setting in the GAME ASSIGNMENTS screen. Set the machines to 1, 2, 3 and 4 sequentially in order starting from the leftmost machine facing the screen. Set every number correctly without duplicating.

(GC) Cause all of the machines to exit from the test mode by selecting EXIT in the System Test Menu.

@ Exiting from the test mode causes the unit to perform the network check automatically. The Network Check screen appears on the screen.

When finishing the network check successfully, the Advertise Screen appears. Normally the network check finishes within several 10 seconds. If the screen does not proceed from the Network Check screen, some sorts of errors such as the error of the setup, the error of cable connection, and malfunctioning the communication cables, etc. can be considered.

Page 124

20 - 4 CAUTIONS TO BE HEEDED DURING COMMUNICATION PLAY

@ During communication play, if communication is interrupted due to some cause, the game is discontinued and the Network Check screen is displayed. If one of the linked machines enters the Test Mode, all others display the Network Check screen.

Even if it has set to the communication play, you can setup a different charge A wrong charge setup may cause the problems of income and outgo

for every machine. A wrong charge setup may cause the problems of income and outgo.

Machine's operation when linked for communication play alters comparing to that of when independently operated. Be careful of this point. When any game machine is in a Test Mode, a Network Check screen appears on the other game machines interconnected for a communication play. While a guest is using any one of the interconnected game machines, therefore, do not activate a Test Mode even on the unused game machine.

Page 125
  • PARTS LIST (@) TOP Assy WRG

+ 2) WRG-0500 ASSY PTV

+ G) WRG-1000 ASSY FRONT CABINET

L (£6) WRG-3000 ASSY REAR CABINET

  • @) WRG-0510 PTV W/STICKER WRG

t- 4) WRG-0550 ASSY BILLBOARD

L G)MGL-1150 ASSY MASK

  • @ WRG-1001 ASSY SUB CABINET

L- (10) WRG-1020 ASSY SERVICE LID

t~ (11) WRG-1030 ASSY LOWER LID

t~ (12) WRG-4000 ASSY MAIN BD

t- (13) WRG-4100 ASSY DRIVE BD

L- (14) WRG-4200 ASSY PWR SPLY

_ (13) NCR-1090 AC UNIT

7 (2) wRG-3001 MAIN BODY

+ (8) WRG-3100 ASSY MECHA BASE

+ 26) WRG-3320 ASSY LID L

  • @7) WRG-3340 ASSY LIDR
  • @8) WRG-3360 ASSY STEP L

+ @9) WRG-3380 ASSY STEP R

t— 60) WRG-3500 ASSY COINCHUTE TOWER

[- G2) WRG-3600 ASSY HANDLE MECHA

  • G3) MIT-3650 ASSY CENTERING MECHA
  • WRG-6001 ASSY WIRE TUBE > ®

t+ @

———_ &

r &

FO STR-1070 FAN UNIT

@) wrG-6002 ASSY WIRE FRONT DC

WRG-3101 MECHA BASE

MJT-3180 ASSY REGU

WRG-3200 ASSY VALVE

MST-3220 ASSY FRONT CYLINDER

MSJT-3240 ASSY REAR CYLINDER

MSJT-3380 VR UNIT

COMPRESSOR & COMPRESSOR BOX

WRG-6003 ASSY WIRE BASE DC

STR-1070 FAN UNIT

WRG-3550 SW UNIT

Page 126

C) Top ASSY WRG (D-1/2)

Page 127
  • TOP ASSY WRG

ITEM NO. PART NO.

1 WRG-0500 2 WRG-1000 3 WRG-3000 4 DYN-0011

5 421-7308-~

11 440-CS0186-EG 12 440-WS0002XEG 13 421-8479-01 14 MJT-0004 15 MSJT-0005 16 SGM-4357 17 SGM-4390 18 WRG-0501 19 421-11466-01

201 000-T00530-0B 202 068-552016-0B 203 000-T00520-0B 204 000-T00408-0C

205 008-T00412-0B

401 601-6604-70 402 420-6659-01 403 420-6455-01 404 SGM-2675X 405 220-5576 406 SGM-4111X 407 WRG-0003 409 220-5373 220-5484 410 514-5036-7000 411 090-0037 412 600-6275-0700 413 310-5285-290100 414 310-5286-29 415 WRG-0502 416 600-7228 600-6729 600-6619 600-6618 600-6695 4l7 600-6664-02

418 280-5009-01

/ 105-5356 / 421-8740 / 421-6690-06 / 421-6690-01 / 421-6690-03 / 421-6690-05 / 421-6119-91 / 421-6120-93 DESCRIPTION

ASSY PTV ASSY FRONT CABINET ASSY REAR CABINET DENOMI PLATE W/O ORIGINAL Locally supplied. DENOMI SH 1GAME ~ Locally supplied. STICKER C EPILEPSY 40 ENG STICKER W POWER OFF ENG STICKER INSTR SUNLIGHT ENG SHIPPING BRKT L SHIPPING BRKT R POLY COVER 1600 X 1300 X 1050 POLY COVER 1150 X 400 X 650 SIDE LID INSTR SH TRANSPORT WRG ENG

MSCR TH BLK MS X 30 FLT WSHR BLK 5.5-20 X 1.6 MSCR TH BLK MS X 20 MSCR TH CRM M4 X8 Locally supplied. TMP PRF SCR TH BLK M4 X 12 Locally supplied.

CARTON BOX 70 OWNERS MANUAL WRG ENG SERVICE MANUAL NAOMI ENG. POLYETHYLENE BAG 240 X 370 KEY MASTER FOR 220-5575 KEY BAG STICKER NUMBER WRG OPTIONAL ‘VOL CONT B-5K VOL CONT B-SK OHM FUSE 6.4 X 30 7000MA 125V SEAL TAPE ASSY FIBER CABLE 5 0700CM FLEX TUBE 29-0100CM. CONN 29 FIBER PLATE AC CABLE CONNECT TYPE 15A AC CABLE CONNECT TYPE 15A AC CABLE CONNECT TYPE FOR UK. AC CABLE CONNECT TYPE FOR EXP (D-2/2)

NOTE

OTHERS USA OTHERS USA

OTHERS USA OTHERS USA

) TAIWAN

’ HONG KONG AC 220 ~240V AREA AC CABLE CONNECT TYPE USA ISA USA WIRE HARN EARTH W/LUG M6 NOT USED CORD CLAMP 21

SHIPPING BRKT

CAUTION INSTR COP U/R STICKER 110V STICKER 120V STICKER 220V STICKER 240V STICKER FCC STICKER SEGA USA TAIWAN OTHERS

AC 110V AREA AC 120V AREA AC 220V AREA AC 240V AREA

) USA

Page 128

(@) ASSY PTV (WRG-0500)

oOo &

ITEM NO. PART NO. DESCRIPTION NOTE

1WRG-0510PTV W/STICKER WRG
2MGL-1150ASSY MASK

3 WRG-0550 ASSY BILLBOARD 5 RAL-0501 MASK HOLDER

4HOD-1101PTV HOLDER
201000-F00412M SCR FH M4 X 12
202000-P00516-WM SCR PH W/FS MS X 16
203000-P00520-WBM SCR PH W/FS BLK MS X 20
204000-T00525-0BM SCR TH BLK M5 X 25
205068-552016-0BFLT WSHR BLK 5.5-20 X 1.6
Page 129

G) PTV WISTICKER WRG (WRG-0510)

ITEM NO. PART NO.

1 WRG-0511 WRG-0512

101 200-5788-31 DESCRIPTION

NOTE

STICKER PTV SIDE L STICKER PTV SIDER

PROJECTION DSPL T SOTYPE 31K, _/ \

Page 130

@) ASSY BILLBOARD (WRG-0550) (D-1/2)

jaa] =) / Oo [a4 fe) = ie) é Z a yn =| 4s foe)

Z ES

Page 131

G) ASSY BILLBOARD (WRG-0550)

ITEM NO.

ANWAWNE PART NO.

WRG-0551 WRG-0552 ASK-1224 ASK-1225 WRG-0553 253-5457

421-7501-18

440-WS0002XEG 440-WS0012XEG

390-6659-32EX

280-5009-01

000-F00410 000-T00408-0B 000-P00430-S

068-441616-0B 000-P00408-W

WRG-60057 DESCRIPTION

LEFT COVER RIGHT COVER BILLBOARD BOX BILLBOARD HOLDER BILLBOARD PLATE FL HOLDER Locally supplied. STICKER FL32W Locally supplied. STICKER W POWER OFF ENG STICKER W HIGH TEMP ENG

ASSY FL32W EX W/CONN HIGH S CE Locally supplied. CORD CLAMP 21

M SCR FH M4 X 10 MSCR TH BLK M4 X8 MSCR PH W/S M4 X 30 Locally supplied. FLT WSHR BLK 4.4-16 X 1.6 M SCR PH W/FS M4 X 8

WH FL (D-2/2)

NOTE

OTHERS USA OTHERS USA

OTHERS USA

OTHERS USA

Page 132
  • ASSY MASK (MGL-1150)

ITEM NO. PART NO. DESCRIPTION NOTE

1MGL-1102TV MASK
2MGL-1151SLIT PLATE
3MGL-1152MASK SIDE HOLDER
201012-F00408-0BTAP SCR FH BLK 4 X 8
202000-F00410M SCR FH M4 X 10
Page 133

(D-1/2)

© ASSY FRONT CABINET (WRG-1000)

Page 134
  • ASSY FRONT CABINET (WRG-1000) (D-2/2)

ITEM NO.

CHOIDARwWNH PART NO.

WRG-1001 WRG-1020 WRG-1030 WRG-4000 WRG-4100 WRG-4200 NCR-1090 WRG-1006 WRG-1007-01

000-P00435-S 000-T00416-0B 068-441616 000-P00408-W 000-P00535-S 068-552016 000-T00425-0B

DESCRIPTION NOTE

ASSY SUB CABINET ASSY SERVICE LID ASSY LOWER LID ASSY MAIN BD ASSY DRIVE BD ASSY PWR SPLY AC UNIT STICKER SERVICE LID PLAY INSTR SH WRG ENG

MSCR PH W/S M4 X 35 M SCR TH BLK M4 X 16 FLT WSHR 4.4-16 X 1.6 M SCR PH W/FS M4 X 8 M SCR PH W/S MS X 35 FLT WSHR 5.5-20 X 1.6 M SCR TH BLK M4 X 25

Page 135

(D-1/2) 1001)

@) ASSY SUB CABINET (WRG

Page 136

@) ASSY SUB CABINET (WRG-1001) (D-2/2)

ITEM NO. PART NO.

WRG-1002 STR-1070 FRQ-1009 FRQ-1012 117-5284 HOD-1003 253-5460-01 253-5396-91 WRG-1003 WRG-1004 WRG-1005 WRG-1008 WRG-1009 WRG-1010 WRG-1011 WRG-1012 WRG-1013

601-5699X 601-9377 601-6224 280-5009-01 280-0419 601-0460 601-10369 117-5402-06-91 130-5228 560-5459 560-5446-H

008-T00416-0B 030-000630-SB 000-P00420-W 050-F00400 000-T00416-0B 050-H01600-0B 030-0006 16-W 011-FO0312 O11-T03512 000-P00516-S 000-F00416 012-P00512-0B 000-P00408-W 050-H00400 060-F00400 060-S00400 068-552016

WRG-6002 WRG-60018 WRG-60019 WRG-60059 WRG-60060 600-7009-1000 600-6972-1900 600-6972-1800 600-6972-1100 DESCRIPTION NOTE

WOODEN FRONT CABINET FAN UNIT LEG CASTER BRKT A LEG CASTER BRKT B PLATE 6-80 BLACK LOCKING BRKT HOD AIR VENT BLACK CABINET HANDLE SPEAKER BRKT SPEAKER PLATE CONNECTOR PNL BRKT CABI STICKER FRONT CABI L STICKER FRONT CABIR STICKER SPEAKER UPPER L STICKER SPEAKER UPPER R. STICKER SPEAKER LOWER L STICKER SPEAKER LOWER R

LEG ADJUSTER BOLT M16 X 75 CASTER FAI=75 CASTER 75 CORD CLAMP 21 HARNESS LUG PLASTIC TIE BELT 100 MM STEREO PWR AMP 47 EARTH TERMINAL PLATE 6P SPEAKER BOX 40HM 40W XFMR 100-120V 100V10A (NM) AC 110 ~ 120V AREA XFMR 220-240V 100V 10A CE (NM) AC 220 ~240V AREA

TMP PRF SCR TH BLK M4 X 16 HEX BLT BLK W/S M6 X 30 M SCR PH W/FS M4 X 20 FLG NUT M4 M SCR TH BLK M4 X 16 HEX NUT BLK M16 HEX BLT W/FS M6 X 6 TAP SCR #1 FH 3 X 12 TAP SCR TH 3.5 X 12 M SCR PH WIS MS X 16 M SCR FH M4 X 16 TAP SCR #2 PH BLK 5 X 12 M SCR PH W/FS M4 X 8 HEX NUT M4 FLT WSHR M4 SPR WSHR M4 FLT WSHR 5.5-20 X 1.6

ASSY WIRE FRONT DC WH EXT AC UNIT WH FRONT AC WH EXT XFMR A WH EXT XFMR B ASSY RGB CA D-SUB 15P 1000MM. WIRE HARN EARTH IDS 1900MM WIRE HARN EARTH IDS 1800MM. WIRE HARN EARTH IDS 1100MM.

Page 137

FAN UNIT (STR-1070)

ITEM NO. PART NO. DESCRIPTION NOTE

1105-5340-01FAN BRKT LONG
101260-0011-02AXIAL FLOW FAN AC100V 50-60HZ

102 601-8543 RD

201000-P00312-WM SCR PH W/FS M3 X 12
Page 138

(@) ASSY WIRE FRONT DC (WRG-6002)

ASSY WIRE FRONT DC (WRG-6002) is comprised of the following wire harnesses. An ASSY DRG. is unavailable.

ITEM NO. PART NO.

601-0460

WRG-60020 WRG-60021 WRG-60022 WRG-60023 WRG-60024 WRG-60025 WRG-60026 WRG-60027 WRG-60028

DESCRIPTION NOTE

PLASTIC TIE BELT 100 MM

WH AMP AUDIO WH AMP VR WH SPEAKER L WH SPEAKER R WH EXT SSR BD SIG WH EXT ETR F WH EXT I/OF WH EXT COINCHUTE F WH EXT VRF

Page 139

ASSY SERVICE LID (WRG-1020)

O°

i i i

ITEM NO. PART NO. DESCRIPTION NOTE 1 WRG-1021 SERVICE LID

2 TH-1015 LOCKING TONGUE

101 220-5575 CAM LOCK MASTER W/O KEY

Page 140
  • ASSY LOWER LID (WRG-1030)

—\ / myn

  • (7 an a, LEX / / /

a E / / / / i / / / / / Vv

=H See =——— oi = oe

L

ITEM NO. PART NO. DESCRIPTION NOTE 1 WRG-1031 LOWER LID

2 253-5460-01 AIR VENT BLACK

201 000-T00416-0B M SCR TH BLK M4 X 16

Page 141

(@®) ASSY MAIN BD (WRG-4000)

NOTE : MAKE SURE THAT THERE IS NO WIRING, ETC. IN THE SLASH MARK PORTIONS.
ITEM NO.PART NO.DESCRIPTIONNOTE
1WRG-4001WOODEN BASE MAIN BD
2840-0064D-01ASSY CASE NAO WRG USAUSA
840-0064D-02ASSY CASE NAO WRG EXPOTHERS
840-0064D-03ASSY CASE NAO WRG KORKOREA
840-0064D-04ASSY CASE NAO WRG AUSAUSTRALIA
3TMB-4003SW REGU BRKT
101400-5397-01SW REGU FOR JVS VA
102280-5277CORD CLAMP 18
103280-0419HARNESS LUG
104601-0460PLASTIC TIE BELT 100 MM
201000-P00416-WM SCR PH W/FS M4 X 16
203000-P00406-WM SCR PH W/FS M4 X 6
204011-F00312TAP SCR #1 FH 3 X 12
205011-T03512TAP SCR TH 3.5 X 12
301WRG-60009WH NAOMI SW REGU AC
302WRG-60010WH NAOMI SW REGU DC
303WRG-60011WH NAOMI AUDIO
304600-7141-050CABLE JVS TYPE A-B 050CM
305600-7159-020WIRE HARN JVS PWR 020CM
Page 142
  • ASSY DRIVE BD (WRG-4100) ao (D-1/2) Slo)
  • @) OC 1 “a6 Ee rir i CH4,

(OXe) eal @e °®

On 6 6je O OCI CO e@ Iii ;

1 roo |CE

(8)

e®

@) )

Page 143
  • ASSY DRIVE BD (WRG-4100)

ITEM NO.

2, PART NO.

WRG-4101 837-13844 837-13844-02 838-12801

400-5421-01024Y 601-7467 280-5277 280-0419 601-0460

011-T00316 000-P00308-W 011-F00312 011-T03512

WRG-60012 WRG-60013 WRG-60015 WRG-60016 WRG-60017 (D-2/2)

DESCRIPTION NOTE

WOODEN BASE DRIVE BD I/O CONTROL BD 2 FOR JVS FRI 1/0 CONTROL BD 2 W/O 232C DOG DRIVE BD WAVERUNNER

SW REGU LCA10S-24-Y L-LOCK BK CORD CLAMP 18 HARNESS LUG PLASTIC TIE BELT 100 MM

TAP SCR TH 3 X 16 M SCR PH W/FS M3 X 8 TAP SCR #1 FH 3 X 12 TAP SCR TH 3.5 X 12

WH DRIVE DC WH DRIVE VO WH DRIVE 24V WH DRIVE SIG WH DRIVE SW REGU AC

Page 144

(D-1/2) ASSY PWR SPLY (WRG-4200) _(

“SNOLLUOd WAV HSVTS AHL NI “OLA “DNIUIM ON SI AYTHL LVH.L TYNS AAV : ALON

Be CE) &

REO GX 7) mt VY \ CA eae de» -6

rs) Le fe) / \ g HL i :

Page 145

ASSY PWR SPLY (WRG-4200)

ITEM NO.

YAURWNHE PART NO.

WRG-4201 838-11856-01-UL 839-0619 NCR-4202 421-7468-01 421-6595-11 WRG-4202

560-5426-V 560-5422-V 450-5138 512-5046-10000 514-5036-7000 117-5225 280-5277 280-0419 601-0460

011-P00325 000-P00416-W 011-T03512 011-T00316 011-F00312

WRG-60001 WRG-60002 WRG-60003 WRG-60004 WRG-60005 WRG-60006 WRG-60007 WRG-60008 WRG-60014 (D-2/2)

DESCRIPTION NOTE

WOODEN BASE PWR SPLY CONNECT BD W/FUSE & COVER UL SSR BD 10 C.P.BRKT STICKER C.P W/PIC STICKER 7A CONNECTOR PNL BRKT PWR SPLY

XFMR 100-120V 100V5.5A AC 110 ~ 120V AREA XFMR 200-240V 100V5.5A CE AC 220 ~ 240V AREA SSR AC 40A C.P 10000MA CE UL FUSE 6.4 X 30 7000MA 125V TERMINAL 3P 20A CORD CLAMP 18 HARNESS LUG PLASTIC TIE BELT 100 MM.

TAP SCR PH 3 X 25 M SCR PH W/FS M4 X 16 TAP SCR TH 3.5 X 12 TAP SCR TH 3 X 16 TAP SCR #1 FH 3 X 12

WH PWR SPLY AC A WH PWR SPLY ACB WH PWR SPLY AC C WH COMP CP A WH CONN BD IN WH CONN BD OUT A WH CONN BD OUT B WH SSR BD SIG WH COMP CP B

Page 146
  • AC UNIT (NCR-1090) (D-1/2)

REAR SID

FRONT SIDE

Page 147
  • AC UNIT (NCR-1090)

ITEM NO.

RON PART NO.

JBA-1031 DYN-0402 421-8202 421-7468-01

214-0202 512-5046-15000 512-5046-8000 450-5126 450-5134 450-5133 450-5135 509-5453-91-V-B 270-5115 280-0417

310-5029-K20 280-0419 601-0460

000-P00416-WB 000-P00408-WB 012-P00408 060-F00400 060-S00400 050-H00400

NCR-60001 NCR-60002 NCR-60003 NCR-60004 NCR-60056 (D-2/2)

DESCRIPTION NOTE

AC BRKT NOISE FILTER BASE STICKER EARTH MARK STICKER C.P W/PIC

AC INLET PANEL TYPE C.P 15000MA CE UL AC 110 ~ 120V AREA C.P 8000MA CE UL AC 220 ~240V AREA MAGNET CONTACT S-NI0CX TAIWAN MAGNET CONTACT S-N10CX AC 230V OTHERS MAGNET CONTACT S-N10CX AC 200V KOREA MAGNET CONTACT S-N10CX AC120V_ USA SW ROCKER J8 V-B NOISE FILTER 15A GT-215J TERMINAL BINDING POST BLACK TAIWAN NOT USED OTHERS SUMITUBE F K 20MM HARNESS LUG PLASTIC TIE BELT 100 MM

M SCR PH W/FS BLK M4 X 16 M SCR PH W/FS BLK M4 X 8 TAP SCR #2 PH4X 8 FLT WSHR M4 SPR WSHR M4 HEX NUT M4

WIRE HARN AC UNIT IN WIRE HARN MAIN SW. WIRE HARN M.CONTACT & N.FILTER WIRE HARN AC UNIT OUT WIRE HARN EARTH INLET

Page 148

deeee perso ke

Tee opposite sie (25 }

SCREW FASTENING TORQUE

TO BE M10: 27 Nem

ASSY REAR CABINET (WRG-3000)

(D-1/3)

Page 149

ASSY REAR CABINET (WRG-3000) (D-2/3)

ITEM NO. PART NO.

1 WRG-3100 2, WRG-3320 3 WRG-3340 4 WRG-3360 5 WRG-3380 6 WRG-3500

7 WRG-3600 8 MJT-3650 9 WRG-3001 10 MSJT-3005 11 MSJT-3006 12 WRG-3007 13 WRG-3009 14 MJT-3010 15 MJT-3011 16 MJT-3012 17 MJT-3013 18 WRG-3015 19 WRG-3016 20 WRG-3017 21 MJT-3018 22 WRG-3019 23 WRG-3020 24 440-WS0179-EG 25 WRG-3022 26 WRG-3023 27 MJT-3024 28 MSJT-3025 29 440-WS0082-EG 30 440-CS0083-EG 31 440-CS0084-EG 32 MJT-3029

  • WRG-3030 34 WRG-3031 35 WRG-3032 36 421-11416 38 WRG-3036 39 WRG-3037 40 WRG-3038 41 WRG-3039

101 509-5764 102 509-0161

DESCRIPTION NOTE

ASSY MECHA BASE ASSY LIDL ASSY LIDR ASSY STEP L ASSY STEPR ASSY COINCHUTE TOWER OTHERS Locally supplied. USA ASSY HANDLE MECHA ASSY CENTERING MECHA MAIN BODY CALLAR SLIDE PLATE SW PLATE BELLOWS BELLOWS STOPPER FRONT BELLOWS STOPPER A BELLOWS STOPPER B BELLOWS STOPPER REAR SIDE PIPER PARTITION PLATE PLATE GUARD REAR LID STICKER REAR LID STICKER BASE BACK STICKER W HI TEMP M ENG STICKER BASE SIDE L STICKER BASE SIDE R BELLOWS BRKT FRONT BELLOWS BRKT A STICKER W BASE A ENG STICKER C BASE B ENG STICKER C SEAT END ENG SUSHL SASHR PIPE HOLDER BODY HOLDER STICKER CAUTION FORK HANDLE BOSS COVER TOWER HOLDER SIDE GUARD L SIDE GUARD R

PUSH BUTTON SW IT GREEN W/LAMP SW PB TYPE IT YEL W/LAMP

Page 150

ASSY REAR CABINET (WRG-3000) (D-3/3)

ITEM NO. PART NO.

000-T00412-0B 000-T00412-0C 000-T00512-0B 060-F01800-0B 020-001020-0Z 030-000820-S 030-001025-S 030-001060-S 060-F01000-0B 060-S01000-0B 068-441616-0C 068-A52820 030-000820-SB 060-F00800-0B 008-B00820-0B 000-T00408-0B 030-000850-S FAS-120001

WRG-60048 WRG-6001

DESCRIPTION NOTE

M SCR TH BLK M4 X 12 M SCR TH CRM M4 X 12

M SCR TH BLK MS X 12

FLT WSHR BLK M18 HEX SKT CAP SCR BLK 0Z M10 X 20 HEX BLT W/S M8 X 20 HEX BLT W/S M10 X 25 HEX BLT W/S M10 X 60 FLT WSHR BLK M10 SPR WSHR BLK M10 FLT WSHR CRM 4.4-16 X 1.6 FLT WSHR 10.5-28 X 2 HEX BLT W/S BLK M8 X 20 FLT WSHR BLK M8 TMP PRF SCR BH BLK M8 X 20 M SCR TH BLK M4 X 8 HEX BLT W/S M8 X 50 TAP SCR #2 TH BLK 4 X 10

WH START & VIEW ASSY WIRE TUBE

Page 151

+

OPPOSITE

SIDE

JN

OPPOSITE (7 , ) aye at } ) (16) a ca ( 1 ) (2 aS

  • MAIN BODY (WRG-3001) (D-1/2)
Page 152

@ MAIN BODY (WRG-3001)

ITEM NO. PART NO.

1 WRG-3001-A 2 WRG-3001-D 3 WRG-3001-E 4 WRG-3001-F 5 WRG-3001-G 6 WRG-3001-H 7 WRG-3001-J 8 WRG-3001-K 9 WRG-3001-L 10 WRG-3001-M. 11 WRG-3001-N 12 WRG-3002 13 WRG-3003 14 WRG-3004 15 WRG-3005 16 WRG-3006 17 WRG-3001-P 18 WRG-3001-Q 19 WRG-3001-R 20 WRG-3001-S 21 WRG-3001-T 22 WRG-3001-U 23 WRG-3001-V

201 047-PA3217-0 202 000-T00520-0B 203 030-000820-S 204 068-852216 (D-2/2)

DESCRIPTION NOTE

MAIN BODY BLANK REAR GUARD JOINT FRAME NUT PLATE A SIDE COVER HOLDER REAR LID FOOT MAT L FOOT MATR STICER SHARK. STICER NO.1 L STICER NO.IR CENTER COVER SIDE COVER L SIDE COVERR SEAT BASE SEAT STICKER SIDE LINE L STICKER SIDE LINE R STICKER PROTECTOR L STICKER PROTECTOR R STICKER BODY REAR STICKER YAMAHA LARGE L STICKER YAMAHA LARGE R

RVT OPEN TYPE AL 3.2 X 17.0 M SCR TH BLK M5 X 20 HEX BLT W/S M8 X 20 FLT WSHR 8.5-22 X 1.6

Page 153

YELLOW

a

RED BLACK YELLOWYELLOW GREEN GREEN BLUE BLACK CLEAR RED

Oo

ASSY MECHA BASE (WRG-3100)

“Apply greasing to sphere portions

‘of the rod end.

TORQUE

M10: 27 Nem M12: 48 Nem M14: 76 Nem M16: 95 Nem MI18:110 Nem M22:170 Nem (D-1/3)

Page 154

ASSY MECHA BASE (WRG-3100) (D-2/3)

ITEM NO.

ll PART NO.

WRG-3140

MJT-3160

MJT-3180 WRG-3200 MJT-3220 MJT-3240 MJT-3380 WRG-3101 WRG-3102 MJT-3103 MJT-3104 MJT-3105 MJT-3106 MJT-3107 WRG-3108 WRG-3109 GLC-3016 253-5460-01 STR-1070

100-5025 111-0019 601-6959 370-5130 601-6843-30570 601-6843-40720 601-6844-00400 601-6844-00540 601-6844-10400 601-6844-10540 601-6844-20540 601-6844-30580 601-6844-80850 601-8898 280-5009-01 280-5169 280-5275-SR10 280-5188-1N 601-6844-80540 601-6844-40720 601-6231-C135 601-5526-370 601-0460 DESCRIPTION NOTE

ASSY COMP OTHERS Locally supplied. USA ASSY TANK OTHERS Locally supplied. USA ASSY REGU ASSY VALVE ASSY FRONT CYLINDER ASSY REAR CYLINDER VR UNIT MECHA BASE RIDE FRAME CRANK LINK GUIDE RING SHOULDER SCREW 18 SHOULDER SCREW 22 BANK BRKT HOLDER SENSOR BRKT BANK ROD SCREW AIR VENT BLACK FAN UNIT

BEARING UNIT ROD END 22 THK POS 22 GEAR 64 INCLINATION SENSOR AIR TUBE 6-YELLOW-570 AIR TUBE 6-GREEN-720 AIR TUBE 10-CLEAR-400 AIR TUBE 10-CLEAR-540 AIR TUBE 10-RED-400 AIR TUBE 10-RED-540 AIR TUBE 10-BLUE-540 AIR TUBE 10-YELLOW-580 AIR TUBE 10-BLACK-850 AIR TUBE CORD CLAMP 21 CORD CLAMP TL-20S CORD CLAMP SR10 WIRE SADDLE WS-1N NIKKO WS-IN AIR TUBE 10-BLACK-540 AIR TUBE 10-GREEN-720 EDGING NEW TYPE BUSH 1.6T L=370MM PLASTIC TIE BELT 100 MM

Page 155

ASSY MECHA BASE (WRG-3100) (D-3/3)

ITEM NO. PART NO.

000-P00408-W 000-P00420-W 000-P00520-S 000-T00408-0B 030-001240 050-H01000 050-H01200 050-H01400 050-H01600 060-F01000 060-F01200 060-F01400 060-S01000 060-S01200 060-S01400 060-S01600 068-552016 FAS-500004 FAS-500005 FAS-600002 FAS-600003 028-A00412-P 000-P00308 000-P00412-W 050-H00400 060-F00400 060-S00400

WRG-6003 WRG-60036 WRG-60037 WRG-60040 WRG-60041 WRG-60045 WRG-60062 600-6972-0900

DESCRIPTION NOTE

M SCR PH W/FS M4 X 8 M SCR PH W/FS M4 X 20 MSCR PH W/S MS X 20 MSCR TH BLK M4 X8 HEX BLT M12 X 40 HEX NUT M10 HEX NUT M12 HEX NUT M14 HEX NUT M16 FLT WSHR M10 FLT WSHR M12 FLT WSHR M14 SPR WSHR M10 SPR WSHR M12 SPR WSHR M14 SPR WSHR M16 FLT WSRR 5.5-20 X 1.6 HEX NUT P1.5 M18 HEX NUT P1.5 #1 M22 SPR WSHR M18 SPR WSHR M22 SET SCR HEX SKT CUP P M4 X 12 MSCR PH M3 X 8 M SCR PH W/FS M4 X 12 HEX NUT M4 FLT WSHR M4 SPR WSHR M4

ASSY WIRE BASE DC WH EXT COMP R WH EXT VALVER WH EXT VRU WH EXT INCLI SENSOR WH EXT BUTTON WH FAN WIRE HARN EARTH ID5 0900MM

Page 156

MECHA BASE (WRG-3101)

ITEM NO. PART NO.

601-5882 601-6056-01

050-H01600-3 030-000620-S ca

DESCRIPTION

LEG ADJUSTER 9 60 CASTER @ 50

HEX NUT TYPE 3 M16 HEX BLT W/S M6 X 20

NOTE
Page 157

ASSY REGU (MJT-3180)

ITEM NO. PART NO. DESCRIPTION NOTE

1MJT-3181REGU BRKT
101601-6077REGULATOR
102601-6079BRKT REGULATOR
103601-6933REGULATOR R1000
104601-6934BRKT REGULATOR C-TYPE120
105601-6274AIR JOINT
106601-6862AIR JOINT T-TYPE ET 10PT 1/4
107601-6844-00200AIR TUBE 10-CLEAR-200
201000-P00410-WM SCR PH W/FS M4 X 10
Page 158

(D-1/2) @2) ASSY VALVE (WRG-3200)

UN 6. YL 8/T.Ld WNT. Vel p/1Ld ANOUOL INIOL UV GNSSYO/SLIMI (108) CBYALIM (0) SMG/SIWI (OE) MOTTA/LIIM (408) NaBHOVAVYO (ZOE) NBEHOVAVED (ZOE) Nd (706 Nd 708 ld (708 Nd (908) Nid (EOE \ i Ore /

(gar { (6H) (601) © Ge

; / = i is role)

  • ‘ o / \J ‘oJ

\ / \ \ A) (ow. , wh) zs) \ (Go) (Ozr

Ole f ore Ole Ore \ Ole ay N3HO | ROTTEA. = MOTTA. \ NOTIBA CBYAWYO (10) AVMO/SLINM (LOE) WOO (OT3HS)NOWS (SOE: SNTBIAVED (ZOE) MOTTBMAVES (ZOE WOO (OTSIHS)4OW 78 G0) Nd (70) YN (706) eet Nd (€0E Nd (£06) acer

Page 159

@1) ASSY VALVE (WRG-3200)

ITEM NO. PART NO.

1 WRG-3201 2, WRG-3202 3 WRG-3203 4 MJT-3204 5 838-11856

101 601-6246 102 601-6247-01 103 601-6249 104 601-11063 105 601-6281-01 106 601-8848 107 601-11064 108 601-6083 109 601-6253 110 601-6254 111 601-6258 112 601-6260 113 601-6274 114 601-6719 115 601-8855 116 601-6843-30260 117 601-6843-40260 118 601-6844-10200 119 601-6844-20200 120 601-6844-30200 121 601-6844-40200 122 209-0023 123 280-0419 124 280-5009-01 125 601-0460 126 601-6844-30120

201 000-P00308-S 202 000-P00408-S 203 000-P00330-S 204 000-P00414-W 205 000-P00430-S 206 000-P00510-S 207 011-T00325 208 011-T03512 209 011-F00312

301 WRG-60049 302 WRG-60050 303 WRG-60051 304 WRG-60052 305 WRG-60053 306 WRG-60054 (D-2/2)

DESCRIPTION NOTE

WOODEN BASE VALVE ‘VALVE BRKT F VALVE BRKT R REGU BRKT CONNECT BD

SPEED CONTROLER 1/8 SILENCER 1/8 AIR VALVE 2 PORT AIR VALVE SILENCER 1/4 AIR REGURATOR, AIR VALVE AIR JOINT AIR JOINT AIR JOINT AIR JOINT AIR JOINT AIR JOINT PLUG 1/8 AIR JOINT AIR TUBE 6-YELLOW-260 AIR TUBE 6-GREEN-260 AIR TUBE 10-RED-200 AIR TUBE 10-BLUE-200 AIR TUBE 10-YELLOW-200 AIR TUBE 10-GREEN-200 CONN CLOSED END HARNESS LUG CORD CLAMP 21 PLASTIC TIE BELT 100 MM AIR TUBE 10-YELLOW-120

MSCR PH W/S M3 X8 MSCR PH W/S M4 X8 MSCR PH W/S M3 X 30 M SCR PH W/FS M4 X 14 MSCR PH W/S M4 X 30 MSCR PH W/S MS X 10 TAP SCR TH 3 X 25 TAP SCR TH 3.5 X 12 TAP SCR #1 FH 3 X 12

WH VALVE A WH VALVE B WH VALVE C WH VALVE D WH PITCH ETR WH ROLL ETR

Page 160

@) ASSY FRONT CYLINDER (MJT-3220)

PITCH UP LIMIT SW PATCH DOWN LIMIT SW BLUE - ORANGE/BLUE BLUE - ORANGE/RED BROWN - WHITE BROWN - WHITE

ITEM NO. PART NO. DESCRIPTION NOTE

1MJT-3221PIN
2MJT-3222COLLAR
101111-0026ROD END PHS 18
102111-0049ROD END 16
103601-6274AIR JOINT
104601-8852AIR CYLINDER W4-50-150
105209-0023CONN CLOSED END
106601-0460PLASTIC TIE BELT 100 MM
301600-6790-056WIRE HARN LIMIT SW
Page 161

@3) ASSY REAR CYLINDER (MJT-3240)

ITEM NO. PART NO.

1 MJT-3241 2 GLC-3016

101 111-0018 102 111-0026 103 601-8853 104 601-6715 105 601-6274

201 050-H01000 202 060-F01000 203 060-S01000 DESCRIPTION NOTE

ROD END HOLDER ROD SCREW

ROD END 18 THK POS 18 ROD END PHS 18 AIR CYLINDER B-50-50-50 AIR JOINT 6-1/4 L TYPE AIR JOINT

HEX NUT M10 FLT WSHR M10 SPR WSHR M10

Page 162

VR UNIT (MJT-3380)

ITEM NO. PART NO.

MJT-3381

220-5373 220-5484 601-6555 310-5029-D20 601-0460

028-C00408-P

600-6790-067 DESCRIPTION NOTE

VR BRKT

VOL CONT B-5K VOL CONT B-5K OHM GEAR Z=30 M=0.75 SUMITUBE F D 20 MM PLASTIC TIE BELT 100 MM

SET SCR CH CUP P M4X 8

WIRE HARN PITCH VR

Page 163

@5) ASSY WIRE BASE DC (WRG-6003)

ASSY WIRE BASE DC (WRG-6003) is comprised of the following wire harnesses. An ASSY DRG. is unavailable.

ITEM NO. PART NO.

601-0460

WRG-60038 WRG-60039 WRG-60044

DESCRIPTION NOTE

PLASTIC TIE BELT 100 MM

WH EXTETRR WHEXTVRR WHEXTI/OR

Page 164

ASSY LID L (WRG-3320)

ITEM NO. OV pn DAD@

/ (EMITTER)

PART NO.

WRG-3321 MJT-3363X

370-5071-01 280-5275-SR10

000-P00316-WB 000-T00408-0B 050-H00300

DESCRIPTION NOTE

BASE LIDL SENSOR BRKT R

BEAM SENSOR CORD CLAMP SR10

M SCR PH W/FS BLK M3 X 16 M SCR TH BLK M4 X 8 HEX NUT M3

Page 165

@7) ASSY LID R (WRG-3340)

DOT (202 203» (2 04 hI) / (RECEIVER) \

ITEM NO. PART NO. DESCRIPTION NOTE

1WRG-3341BASE LIDR.
2MJT-3343XSENSOR BRKT L
101370-5071-02BEAM SENSOR
102280-5275-SR10CORD CLAMP SRI10
201000-P003 16-WBM SCR PH W/FS BLK M3 X 16
202000-T00408-0BMSCR TH BLK M4 X 8
203050-H00300HEX NUT M3
Page 166

SIN OS Po a0 4 (3 101 ahaa £4 NL

/ (EMITTER) ASSY STEP L (WRG-3360) (D-1/2)

Page 167

ASSY STEP L (WRG-3360)

ITEM NO.

RON PART NO.

WRG-3361 MJT-3342 MJT-3343X MJT-3344X

370-5071

000-P00316-WB 000-T00408-0B 050-H00300 (D-2/2)

DESCRIPTION NOTE

STEP BASEL SIDE MAT SENSOR BRKT L SENSOR PLATE L

BEAM SENSO

M SCR PH W/FS BLK M3 X 16 MSCR TH BLK M4 X 8 HEX NUT M3

Page 168

ASSY STEP R (WRG-3380)

~~ (RECEIVER) Le, (D-1/2)

Page 169

ASSY STEP R (WRG-3380)

ITEM NO.

RON PART NO.

WRG-3361 MJT-3342 MJT-3343X MJT-3344X

370-5071

000-P00316-WB 000-T00408-0B 050-H00300 (D-1/2)

DESCRIPTION NOTE

STEP BASEL SIDE MAT SENSOR BRKT L SENSOR PLATE L

BEAM SENSO

M SCR PH W/FS BLK M3 X 16 MSCR TH BLK M4 X 8 HEX NUT M3

Page 170

ASSY COINCHUTE TOWER (WRG-3500) (D-1/2)

(2)

LN a —\ >

~ me p yah QL ‘ \2/) ou

y aw ee en a Oy / aw, aA AL 4 SECTION A-A fs 18)

Page 171

ASSY COINCHUTE TOWER (WRG-3500) (D-2/2)

ITEM NO.

CHOIDARwWNH PART NO.

WRG-3550 WRG-3501 BSS-1471 BSS-1472 DP-1167 105-5171 253-5366 421-6591-01 421-7501-02

220-5237-92- ~ 220-5643-01 220-5575 220-5574 280-5009-01 280-5275-SR10 310-5029-F20 601-0460

000-P00408-W

600-6455-02 600-6972-0150 WRG-60046 WRG-60047 DESCRIPTION NOTE

SW UNIT COIN CHUTE TOWER METER BRKT METER HOLE LID TNG LKG CHUTE PLATE SINGLE CASH BOX STICKER COIN METER STICKER 6.3V 0.15A

ASSY C.C 2DR ~ MAG CNTR DCSV 6P WH MZ-674-D04 CAM LOCK MASTER W/O KEY CAM LOCK W/KEYS CORD CLAMP 21 CORD CLAMP SRI10 SUMITUBE F F 20MM PLASTIC TIE BELT 100 MM

M SCR PH W/FS M4 X 8

WIRE HARN C.C DOOR SINGLE WIRE HARN EARTH IDS 0150MM. WH EXT SOUND VR C WH EXT COINCHUTE C

Page 172

G1) SW UNIT (WRG-3550)

ges ave r 7

\ / / \ / /

ae TEST / ih / / / / / / / / / / i

i af f— . ~~

  • (2) NY NY

ITEM NO. PART NO. DESCRIPTION

1WRG-3551SW BRKT
2421-11430STICKER SW UNIT
101220-5179VOL CONT B-5K OHM
102509-5028SW PB IM
103601-0042KNOB 22 MM
104310-5029-D20SUMITUBE F D 20 MM
105601-0460PLASTIC TIE BELT 100 MM
301WRG-60055WH SOUND VR
302WRG-60056WH TEST & SERVICE
NOTE
Page 173

SCREW FASTENING TORQUE

TO BE M6: 9.8 Nem (100kgf*cm)

G2) ASSY HANDLE MECHA (WRG-3600)

(D-1/2)

Page 174

@2) ASSY HANDLE MECHA (WRG-3600) (D-2/2)

ITEM NO. PART NO.

MJT-3601 MJT-3602 WRG-3603 MJT-3604 WRG-3605 WRG-3606 MJT-3607 MJT-3608 MJT-3610 MJT-3611 MJT-3612 601-7945 WRG-3614 WRG-3609-E

220-5373 220-5484 310-5029-F20 280-5275-SR10 610-5027-1001 601-0460 509-5329

028-A00308-P 065-E00400 000-T00408-0B 050-F00400 068-552016-0B 000-T00525-0B 020-000620-0Z 060-S00600-0B 060-F00600-0B 068-441616-0B 000-T00406-0B 000-T00308-0C

600-6790-074 600-6790-121 600-6790-096 600-6790-097 DESCRIPTION NOTE

ACCEL LEVER RACK GEAR MOUNT BLOCK ACCEL COVER A ACCEL COVER B WRG HANDLE SHAFT TORSION SPRING COLLAR ACCEL VR BRKT HANDLE GRIP HANDLE HOLDER GEAR 20 SPACER STICKER MOTION STOP

VOL CONT B-5K VOL CONT B-5K OHM SUMITUBE F F 20MM. CORD CLAMP SR10 INSL SLIT TUBE ID 10 PLASTICK TIE BELT 100 MM PUSH BUTTON SW IT RED

SET SCR HEX SKT CUP P M3 X 8 E RING 4MM M SCR TH BLK M4 X 8 FLG NUT M4 FLT WSHR BLK 5.5-20 X 1.6 M SCR TH BLK M5 X 25 HEX SKT H CAP SCR BLK 0Z M6 X 20 SPR WSHR BLK M6 FLT WSHR BLK M6 FLT WSHR BLK 4.4-16 X 1.6 M SCR TH BLK M4 X 6 M SCR TH CRM M3 X 8

WIRE HARN ACCEL VR. WIRE HARN EXT ACCEL VR IEC WIRE HARN EXT EMERGENCY SW WIRE HARN EMERGENCY SW

Page 175

(210209) 208) UIA (201) er

63) ASSY CENTERING MECHA (MJT-3650)

(D-1/2)

Page 176

@3) ASSY CENTERING MECHA (MJT-3650) (D-2/2)

ITEM NO. PART NO.

MJT-3651 MJT-3652 MJT-3653 MJT-3654 MJT-3655 MJT-3656 MJT-3657 MJT-3658 MJT-3659 TTR-2010 601-6555 601-6450 RDY-2106

100-5096 100-5043 601-8847 310-5029-F20 220-5373 220-5484 280-5275-SR10

050-F00600 060-F00800 060-S00800 050-H00800 030-000612-SB 060-F00600 000-P00408-W 060-F01200 060-S01200 050-H01200 028-A00410-P

600-6790-072 DESCRIPTION NOTE

MAIN SHAFT STOPPER COLLAR B MECHA CASE A MECHA CASE B LOSTA HOLDER HOLDER VR HOLDER SHAFT GEAR HOLDER 110 GEAR Z=30 M=0.75 GEAR 110 VR BRACKET

BEARING 17 BEARING 25 FYH SBP FL 205 LOSTA DR-S-18 X 30 SUMITUBE F F 20MM VOL CONT B-5K VOL CONT B-5K OHM CORD CLAMP SR10

FLG NUT M6 FLT WSHR M8 SPR WSHR M8 HEX NUT M8 HEX BLT W/S BLK M6 X 12 FLT WSHR M6 M SCR PH W/FS M4 X 8 FLT WSHR M12 SPR WSHR M12 HEX NUT M12 SET SCR HEX SKT CUP P M4 X 10

WIRE HARN STEERING VR.

Page 177

ASSY WIRE TUBE (WRG-6001)

BPP WHTEL-P (WR6-60030)_ OPPMHTEU? | iv 80 / 3P,P.WHATE,9090_ PP WATE sos ‘(WRG-60029) LU Tet Luo al ie. a0 ovaresiO— | SPPREDUP 1m) iin U eepacnue (WRG-6003 O ‘SPPREDUP fam OD WPPREDUP “(WRG-60034) | ons

  • fe) (101) repens Ned .

ITEMNO. PART NO. DESCRIPTION NOTE

1WRG-0001TUBE BRKT FRONT
2WRG-0002TUBE BRKT REAR
101310-5285-290060FLEX TUBE 29-0060CM
102310-5286-29CONN 29
103601-10360-29STOPPER RING 29
201050-H00400HEX NUT M4
202060-F00400FLT WSHR M4
203060-S00400SPR WSHR M4
301WRG-60029WH EXT COMP T
302WRG-60030WH EXT VALVE T
303WRG-60031WHEXTETRT
304WRG-60032WH EXT VRT
305WRG-60033WH EXT SOUND VR T
306WRG-60034WH EXT COINCHUTE T
307WRG-60035WHEXTI/OT
308600-6972-0350WIRE HARN EARTH IDS 0350MM
309600-6972-1200WIRE HARN EARTH IDS 1200MM
Page 178
  • COMPRESSOR & COMPRESSOR BOX

COMPRESSOR BOX

P-3SHD f

PART NO. DESCRIPTION QTY

999-0167 999-0169 NO PART NUMBER NO PART NUMBER LOCAL PURCHASE LOCAL PURCHASE-CKD LOCAL PURCHASE-CKD LOCAL PURCHASE-GRN NO PART NUMBER LOCAL PURCHASE-CKD LOCAL PURCHASE -CKD LOCAL PURCHASE -CKD LOCAL PURCHASE -CKD LOCAL PURCHASE -CKD LOCAL PURCHASE -CKD LOCAL PURCHASE -CKD LOCAL PURCHASE -CKD NO PART NUMBER 999-1373 999-1374 999-1372 LOCAL PURCHASE-GRN LEVELER LEG 1/2-13 X 3” L 45 0T-08302-21PC CASTER 160-2 1/2 #25188 SWIVEL S/A; PLATE LEG LEVELER WOOD BOX COMPRESSOR, OUTLET POWER AC RECEPTACLE 1” TUBING BLACK 2 FEET CONNECTOR 1” DIA. STRAIGHT ANGLE FAN 110/120 VAC 17/15 W SINWAN S109AP 11-1 WOOD DOOR COMPRESSOR TUBING BLACK 7.250 TUBING BLACK 24” JOINT (COMPRESSOR)R/A 1/4 CKD #GWL 10-8 JOINT (COMPRESSOR)ST 3/8” FEMALE CKD #GWS-10-8-M FILTER AIR CKD-F3000-10-F1 FILTER OIL MIST CKD-M3000-10-F1 JOINT (COMPRESSOR) R/A 3/8 CKD #GWL 10-10 JOINT (COMPRESSOR)ST 3/8” FEMALE CKD #GWS-10-10 WOOD BOARD COMPONENT COMPRESSOR ARTWORK COMPRESSOR BOX LEF ARTWORK COMPRESSOR BOX RIGHT ART WORK COMPRESSOR BOX LID COMPRESSOR THOMAS #T-35HD GRAINGER #6B515 Be ee ee ee ee Re ee DDE RENAN

Page 179

WAVERUNNER GP COMPRESSOR TANK

There is a petcock provided on the bottom of the compressor box to enable draining of accumulated condensation from the compressor tank. It is recommended to drain any moisture from the tank at least once a week to minimize oxidation and extend the life of the tank.

The petcock is located on the bottom of the cabinet on the players left and may be accessed without opening the compressor box lid.

Figure 2 Bottom View - Petcock Access

Page 180
  • WIRE COLOR CODE TABLE

THE WIRE COLOR CODE is as follow:

PINK

SKY BLUE

BROWN

PURPLE

LIGHT GREEN mOoOaAwe

Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters.

RED

BLUE

YELLOW

GREEN

WHITE

ORANGE,

BLACK

GRAY CamrrIneEwWwNe

If the right-hand side numeral of the code is 0, then the wire will be of a single color shown by the left-hand side numeral (see the above).

Note 1: If the right-hand side alphanumeric is not 0, that particular wire has a spiral color code. The left-hand side character shows the base color and the right-hand side one, the spiral color.

<Example> 51............. WHITE / RED

NOON OX

RED WHITE

Note 2: The character following the wire color code indicates the size of the wire.

U: AWGI16

K: AWGI18

L: AWG20

‘None: AWG22

Page 181

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 182

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 (650) 632-7580 phone (650) 632-7594 fax