CATHODE RAY TOMES

Hard Drivin' Compact TM-329 2nd Printing

Hard Drivin' Compact (Atari Games Corporation, 1989) · Technical Manual · 104 pages · 126 sections · original scan

Page 1

TM-929

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 4

Copyright © 1989 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O, Box 361110 Milpitas, California 95035

Printed in the U.S.A 6/89

Produced by the Atari Games Technical Publications Department. Technical Writing: Rosalind Hutton Editing: Andrea Dencker Mustration and Design: Mary Ohanessian Sumner Hard Drivin’ Compact

Notice Regarding Non-Atari® Parts

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-Atari parts in the game. © Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.

NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMI) ground cage, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

Hard Drivin’ Compact

Contents

1 Set Up How to Use This Manual Operating the Simulator. Inspecting the Simulator. Adjusting the Glides .... Control and Switch Locations Setting the Coin and Game Options. Simulator Systems ... Maximizing Earnings Simulator Driving .. Bie SWHANNKHNKE iS 2 Self-Test and Diagnostic 2-2 12-2 2-3 Entering and Exiting the Self-Test Automated Self Test..... Program ROM and RAM Test. Microprocessor and Board Tests Test Menu Screens....

Custom Game Options Statistics... Histogram, Error Count Games Played by Day and Hour Set Controls Screens Control Inputs Screen ..... Monitor Test Patterns Set Clock Screen .... Disable Broken Controls Screen Special Functions Screen Main Board GSP Tests . Main Board MSP Tests Main Board Controls. 2-15 Steering Wheel Submenu... 2-16 Main Board ROM Checksums 2-16 Main Board ZRAM Test 2-17 ADSP Board Tests . 2-17 Sound Board ... 2-18 LEDs on the Main PCB .

3 Maintenance and Troubleshooting 3-3 3-3 3-3 Removing the Dashboard 2. Installing the Dashboard -. 3-3 Interior Components... 3-3 Cleaning the Interior Components 3-4 Key Switch Assembly ....... 3-4 @ A Oiling the Key Switch Assembly. Replacing the Spring in the Key Switch Assembh Tightening the Screw in the Key Switch Assembly Actuator... sess Replacing the Switch on the Key Switch Assembl Pedals If the Gas or Clutch Pedal Does Not Work .. If the Brake Pedal Does Not Work Greasing and Checking the Pedals Replacing a Pedal. Replacing a Spring. Replacing the Clutch and Gas Pedal Potentiometers ..... sveeneceeneseseen Testing the Brake Pedal Strain Gauge and Bonding Replacing the Brake Strain Gauge . Shifter Assembly... Lubricating the Shifter. Replacing a Shifter Switch Speakers .. 3-14 Removing a Speaker . 3-16 Static-Sensitive Devices . 3-16 Replacing Static-Sensitive Device: Steering Assembly Oiling the Bronze Bearing Adjusting the Steering Belt Replacing the Steering Bel Replacing the Steering Moto! Replacing the Encoder or Centering PCB. Replacing the Centering Disk. Replacing the Encoder Disk..

Video Display ...... Adjusting the Video Display Removing the Video Display . Replacing the Video Display 4 Illustrated Parts Lists See the list of Illustrations that follows.

Statistics Sheet

iii

Page 6

Figure 2-1 Figure 2-2

Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11

Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15 Figure 2-16 Figure 2-17 Figure 2-18 Figure 2-19 Figure 2-20 Figure 2-21 Figuie 2-22 Figure 2-23 Figure 2-24 Figure 2-25

Figure 2-26 Figure 2-27

Figure 2-28

Figure 3-1 Figure 3-2 Figure 3-3

iv Hard Drivin’ Compact

Illustrations

Program ROM and RAM Test Screen.. 2-3 Microprocessor and Board Tests Screen... Instructions for Test Menu Screen . Test Menu Screen... Coin Options Screen Game Options Screen Custom Game Options Screen, Statistics Screen. Histogram Screen. Exror Counts Screen. Games Played by Day and Hour Screen First Set Controls Screen Control Inputs Screen Set Clock Screen Disable Broken Controls Screen Special Functions Screen GSP Tests Screen . MSP Tests Screen. Main Board Controls Screen Pots: 8-Bit Screen Steering Wheel Submenu Screen. Send Force Screen ROM Checksums Screen. 2-17 ADSP Board Tests Screet 2-17 ADSP ROM Checksums Tests Screen Sound Board Tests Screen... Sound Board Sound Wave ROM Checksums Screen...... i DIP Switch and LED Locations on the Main PCB...

Removing the Dashboard Maintaining the Key Switch ... Gas or Clutch Pedal is Not Working or Is Working Erratically and You Have Tried the Set Controls Screens............. 3-8 Figure 3-4

Figure 3-5

Figure 3-6

Figure 3-7 Figure 3-8 Figure 3-9 Figure 3-10

Figure 3-11 Figure 3-12

Figure 3-13

Figure 3-14

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8

Figure 4-9 Figure 4-10

Figure 4-11 Figure 4-12 Figure 4-13 Figure 4-14 Maintaining the Gas and Brake Pedal Assembly ... avai Brake Pedal is Not Working or Working Erratically and You Have Tried the Set Controls Screens........... 3-11 Maioraining the Clutch Pedal Assembly ......... Maintaining the Shifter Assembly Steering Assembly, Front View... Steering Assembly, Rear View The Steering Wheel Continuously Turns in One Direction and You Have Tried the Set Controls Screens ... Installing the Steering Pivot Shaft..... 3-21 The Steering Wheel is Jerky and You Have Tried the Set Controls Screens ..... The Steering Wheel Has No Feedback and You Have Tried the Set Controls Screens... Removing the Video Display 3-20

3-28

Cabinet-Mounted Assemblies Dashboard Assembly .. Steering Assembly. Shifter Assembly .. Key Switch Assembly . Clutch and Brake Pedal Assembly. Gas Pedal Assembly ... Coin Acceptors, Inc. Coin Door Assembly .... Power Supply Assembly. Hard Drivin’ Compact Main PCB Assembly... APU PCB Assembly Motor Amplifier PCB Assembly Shifter PCB Assembly Brake PCB Assembly .

Page 7

Hard Drivin’ Compact

Table 1-1

Table 2-1

Table 2-2 Table 2-3 Table 2-4

Table 2-5 Table 2-6

Table 2-7 Table 2-8

Table 2-9 Table 2-10

Table 3-1 Tables

Simulator Specifications. 12

Using the Self-Test Screens and Diagnostics 2-2

oe 25, Coin Option Settings Game Option Settings . Summary of All Screens Appearing in the Self-Test .. Custom Game Option Settings.. When to Use the Special Function Items Program ROM Locatiot ADSP Scope Loop Diagnostic coe 226 a 28

Using the DIP Switches

Maintenance and Inspection Items...... 3-2 Table 3-2

Table 3-3 Table 3-4 Table 3-5

Table 3-6 Table 3-7

Table 3-8

Table 3-9

Table 3-10 Table 3-11

Table 3-12

Table 3-13 Voltage Inputs and Test Points on the Simulator PCBs . Troubleshooting All Controls Troubleshooting the Key Switch. Troubleshooting the Clutch or Gas Pedal ..... oe Troubleshooting the Brake Pedal Pedal Potentiometers Harness Connections... we 3-13, Troubleshooting the Shifter Assembly we 3-14 Harness Connections to the Shifter Switches... Troubleshooting the Speake: Troubleshooting the Steering Assembly Torque Table for the Screws in the Steering Assembly.......... Troubleshooting the Video Display ...

Page 8

Hard Drivin’ Compact

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged inte a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded ouilet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap, Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of

vi your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING -— Players and/or technicians can be killed or injured if instructions are not followed.
Page 9

SET-UP

Chapter 1

How to Use This Manual

This manual is written for operators and service personnel. It provides information for setting up, driving, | testing, and maintaining your Hard | Drivin’ Compact™ simulator. The manual is divided into the following chapters: e Chapter 1 contains set-up and simulator driving information. e Chapter 2 contains self-test procedures and additional diagnostic tests. The self-test is important in the Hard Drivin’ compact simulator. You can troubleshoot the PC boards, main circuits, and controls using the more than 60 screens in the self-test. You should regularly test the boards and controls with the self-test to keep your simulator in peak condition and at top earnings. e Chapter 3 contains the preventive maintenance schedule for the simulator and the repair procedures, flowcharts, and troubleshooting tables for each control. If you have problems with your simulator, use this chapter to troubleshoot and to repair it. Be sure to perform the preventive maintenance tasks to keep your simulator in good condition. e Chapter 4 contains the illustrated parts lists.

Page 10

Set-Up

Operating the Simulator

To operate your simulator for maximum income, make sure your players know that the simulator is designed to be driven like a real car. You should regularly do the automated self-test and check the controls with the Control Inputs screen in the self-test. By using the selftest regularly, you can find and fix problems immediately. This lets you keep your simulator in top condition.

Note If you are installing a new PC board or a control in your simulator, go through the Set Controls screen in the self-test. This is explained in Chapter 2. If you turn on your simulator and you see a screen that says Initialize Pot Inputs instead of the attraction screens, then reset the controls by following the instructions on the screens that appear.

Inspecting the Simulator

WARNING To avoid electrically shocking yourself and damaging the simulator electronics, do not plug in the simulator until it has been inspected and set up for your line voltage.

This cabinet should be connected to a grounded threewire outlet only. If you have only two-wire outlets, we recommend that you hire a licensed electrician to install grounded outlets. Players can receive an electrical shock if the cabinet is not properly grounded. Inspect your Hard Drivin’ simulator carefully to ensure that the simulator is complete and was delivered to you in good condition. Inspect the cabinet as follows:

  • Examine the exterior of the cabinet for dents, chips, or broken parts.
  • Open the service door. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Check that all plug-in connectors on the cabinet harnesses are firmly plugged in. Do not force connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed connector can damage a printed-circuit board (PCB). This will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets.

1-2 Hard Drivin’ Compact

c. Inspect the power cord for any cuts or dents in the insulation. d. Inspect the power supply. Make sure that the correct fuses are installed, Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected. ¢. Inspect other sub-assemblies, such as the video display, controls, printed-circuit boards (PCBs), and speakers. Make sure that they are mounted securely and that the ground wires are connected.

Adjusting the Glides

After you move the simulator into location, screw out the adjustable glides in the base to support it. Before you move the simulator, retract the glides so they are not damaged,

Control and Switch

Locations

Most of the controls are located inside the seat, behind the coin door. The only exception is the power on/off switch,

Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet.

Volume Control The volume control is located behind the upper coin door under the seat.

Self-Test Switch The self-test switch is located behind the upper coin door under the seat. See Chapter 2 for a complete description of the self-test.

Page 11

Hard Drivin’ Compact

Auxiliary Coin Switches An auxiliary coin switch is located on the component bracket behind the upper coin door under the seat. Use the auxiliary coin switch to give players coin credits.

Coin Counter The coin counter is located behind the upper coin door. The coin counter records the number of coins deposited. It does not count the credits given by the auxiliary coin switch.

Setting the Coin and Game Options

The Hard Drivin’ Compact coin and game options are set in the self-test. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

’

Simulator Systems

The Hard Drivin’ simulator uses eight PCBs to give a realistic look and feel to the driving. These PCBs are the multisync main PCB, the ADSP PCB, the motor amplifier PCB, the audio and power PCB (mounted on the power supply assembly), two PCBs mounted on the steering wheel, the sound PCB, and the video display board. These PCBs control the simulator software, the video display, and the controls. The multisync main PCB, which is the largest, holds the 68010, the GSP, and the MSP microprocessor systems. The 68010 system contains program RAM and ROM. The GSP (Graphic Systems Processor) microprocessor system controls the video RAMs (VRAMs). The MSP (Model Systems Processor) microprocessor system performs all the math functions. The ADSP board and the sound board are mounted. with the multisync main PCB. The motor amplifier PCB is mounted in a heat sink assembly located on the driver's left. It controls the steering wheel motor using the input from the two boards mounted on the steering assembly.

Maximizing Earnings

For maximum earnings, regularly maintain your Hard Drivin’ simulator following the instructions in Table 3-1, in Chapter 3. When you set up the simulator and when you collect money, perform the automated self-test and check the controls with the Control Inputs screen in the self-test.

Simulator Driving

This section describes the features and driving of the Set-Up

Hard Drivin’ simulator.

Introduction Put your feet on the gas and clutch pedal, one hand on the wheel, and the other on the stick shift. Select manual or automatic transmission, turn the ignition key and you're off! It's the ride of your life. You feel the tires grip the road when you take a wide turn at high speed. You're alerted to the smallest change in the road by the feedback steering. You catch air as you fly the draw bridge and land on the down ramp. You control the car as it holds the road on the dizzying vertical loop.

Driving Mode Hard Drivin’ Compact might look like an arcade game but it drives like a real car. For the best jap times, drive the simulator as if it were a real car. The main difference between Hard Drivin’ Compact and a real car is that the simulator is much safer to drive. A player can test the limits of our car and his skill with no risk of personal injury, and follow a course that does not exist anywhere in the real world. After inserting the proper number of coins, the player can seleci either an automatic or manual transmission. Turning the ignition key starts the simulator. Drivers can choose between the stunt track or the speed track by following the posted signs on the road. Each player has a certain (operator-selectable) amount of time to reach a checkpoint or the finish line, Crossing checkpoints and the finish line rewards the player with (operator-selectable) bonus driving time. With Hard Drivin’ Compact a player can test drive a high-powered sports car on a real stunt course. He can jump a draw bridge, negotiate a high-speed banked turn and drive a 360-degree vertical loop. These thrilling stunts, among others, provide the ultimate realistic driving experience. Or maybe high-speed driving is a particular player’s type of excitement. He can “put the pedal to the metal” and try to keep control around the corners, weaving in and out of waffic while avoiding oncoming cars. All this, and more, await the player behind the wheel of Hard Drivin’ Compact. Players especially enjoy the unique instant replay feature. Every time a player crashes, the simulator records and replays the crash sequence. Not only will the player find this entertaining, but it is also informative. The instant replay shows the player exactly what he did wrong and why he crashed. (If a player wants to skip the instant replay, he can press the abort switch or turn the key when the replay starts.) A skilled player finds the ultimate competition in the “challenge” lap (or “grudge match” as we at Atari Games like to cali it). The simulator remembers the

Page 12

Set-Up Hard Drivin’ Compact

path of the car driven by the best driver on record. When a player beats the qualifying lap time, he challenges the car of the past winner in a head-to-head Tace. Hard Drivin’ Compact is equipped with center-feel steering with continuous force feedback, gas, brake, and clutch pedals, four-speed stick shift, and a 25-inch monitor.

Page 13

SELF-TEST

&

DIAGNOSTICS

Chapter 2

The Hard Drivin’ simulator is a complex machine. To keep it at peak efficiency and maximum earnings, you should regularly check the controls, RAMs, ROMs, PCBs, and microprocessor systems. You can check all of these when you switch on the self-test. Also in the self-test you can check the video display, the statistics, and set the internal clock. If you cannot use the self-test because the screen is dark, you can use a DIP switch on the main PCB to find the source of the problem. If you are having electronic problems, you can check the state of various signals with the LEDs on the main PCB. You should regularly check the following screens and information, We recommend you check these when you first set up the simulator, each time you collect money, or when the simulator is not working correctly. @ Use the automated self-test, which begins automatically when you turn on the self-test to test the program RAMs and ROMs, the video RAMs, color RAMs, the MSP microprocessor system, the ADSP PCB, and the sound PCB. The test takes about 5 minutes to run. e@ Check the Control Inputs screen, which you choose from the Test Menu screen. This shows the voltage input to the main PCB from the gas pedal, the clutch pedal, the brake pedal, the coin mechanisms, the abort switch, the shifter, and the steering assembly. With this information you can easily check how the controls are working.

Note If the control inputs are wrong, your earnings may drop, since the realistic driving feel is lost.

Check the Statistics, Histogram, and Games Played by Day and Hour screens which show the statistical information about how and when your simulator is played.

Page 14

Self-Test Hard Drivin’ Compact

Entering and Exiting Automated Self-Test the Self-Test

To enter the self-test, turn on the self-test switch inside the upper coin door. To exit the self-test, turn it off. If you are in a submenu, you may need to go through all the screens in a sub-menu before you return to the attract mode. For example, if you are in an operator screen and want to go back to the attract mode, turn off the self-test switch, go through all the operating screens, return to the menu screen, and then you will return to the attract mode. When you enter the self-test, the simulator automatically tests the program ROM and RAM, the video RAM, the color RAM, the MSP microprocessor system, the ADSP PC board, and the sound PC board. This test takes about five minutes (unless you bypass it as described in the next paragraph).

Note If you do not see anything on the video display screen, you may have a video display problem or a simulator system problem. See DIP Switches at the end of this chapter to diagnose the probiem.

Table 2-1 Using the Self-Test Screens and Diagnostics

‘Automated Self-Test

Test Menu: Regular ‘Maintenance s

‘Control Problem

Cannot Enter the Self-Test” “When you switch’ on the self-test, 1 RAM. and ROM ‘and the PCBs, Yc

2-2

Page 15

Hard Drivin’ Compact

If you do not want to wait for the systems and PCBs to be tested, then skip these tests by turning the key switch while in the program ROM and RAM screen, Figure 2-1. If you want to go to the attract mode, just turn off the self-test switch,

Program ROM and

RAM Test

When you enter self-test, the simulator tests the program ROM and RAM. The screen in Figure 2-1 shows the results of a program ROM and RAM test.

BAD PROGRAM ROM Is BLANK BOX Yoox W V U-T SR 200 oOo - 2 Oe 210 = 1 8 8 8 ROMS AT 200R AND 210R CONTAIN THE SELF-TEST PROGRAM

PROGRAM RAM OK

HOLD KEY TO BYPASS SELF-TEST

Figure 2-1 Program ROM and RAM Test Screen The top of the screen shows the ROM test result. The numbers on the left and the letters on the top of the screen show the locations of the ROMs on the main PCB. If a white box appears, then the ROM there is good. If an empty box appears (as shown at 200U and 210U), then the ROM there is bad. If nothing appears, then nothing was tested there. The RAMs are tested after the ROMs. If the RAMs have no errors, then you see the message Program RAM OK. If the test finds an error, then you see Bad Program RAM At with the bad RAM location listed. This screen disappears after a few seconds and the self-test continues. However, the screen with the results of the complete self-test, shown in Figure 2-2, will show the message Bad Program ROM (or Bad Program RAM) if it found an error in the program ROMs or RAMs.

Microprocessor and

Board Tests

After checking the program RAM and ROM, the automated self-test checks the simulator’s microprocessor Self-Test

and PC boards, It tests the video RAM and color RAM in the GSP microprocessor system, the DRAM in the MSP microprocessor system, the ADSP board, and the sound board. The test takes four to five minutes. You will see the screen in Figure 2-2 when it finishes.

BAD PROGRAM ROM PROGRAM RAM OK GSP VRAM OK--SIMPLE TEST GSP COLOR RAM OK MSP DRAM OK. ADSP BOARD OK SOUND BOARD OK SOUND WAVE ROMS OK.

TURN KEY TO SELECT TEST MENU

Figure 2-2 Microprocessor and Board Tests Screen

If the system or board is good, OK follows the test name. If it is bad, the word Bad precedes the name of the board or system (except for the ADSP board test, which gives more information). If you have a bad system or board, then choose Special Functions from the test menu, choose the appropriate system or board tests from the special functions menu, and read the description of the tests in this chapter. A brief description of each microprocessor and board test performed in the self-test is below. PROGRAM ROM: Described above. PROGRAM RAM: Described above. GSP VRAM: Uses the Simple GSP VRAM Test. (Described in the section Main Board GSP Tests.) GSP COLOR RAM: Uses the GSP Color RAM Test. (Described in the section Main Board GSP Tests.) MSP DRAM: Uses the MSP Verify Test. (Described in the section Main Board MSP Tests.) ADSP Board: Tests the ADSP board memory and the ADSP-2100. Most of the error messages are self-explanatory. (Does Not Respond generally indicates a missing board.) Sound Board: Tests the program ROM and RAM on the sound PC board. If any are bad, the message Bad Sound Board appears on the screen. Sound Wave ROMS: Tests the ROMs that have the sound wave form data. If any are bad, the message Bad Sound Wave ROMs appears on the screen.

2-3

Page 16

Self-Test

Test Menu Screens

After the microprocessor and board test is finished, or you bypass it, turn the key to see the test menu screens. Turn the key once to see the screen with the instructions for moving and choosing in the test menu, shown in Figure 2-3, Turn the key again to see the test menu.

USING THE TEST MENU

PRESS LEFT COIN SWITCH TO MOVE DOWN OR TO INCREMENT PRESS RIGHT COIN SWITCH TO MOVE-UP OR TO DECREMENT TURN KEY TOCHOOSE ITEM OR TO. RETURN.

Figure 2-3 Instructions for Test Menu Screen

‘To move down the menu, press the left coin switch. To move up the menu, press the right coin switch. ‘You can choose the test menu item with the white letters by turning the key. The test menu, shown in Figure 2-4, is the most important screen in the self-test. Use this screen to choose the other screens and tests in the self-test. If you choose any item on this test menu, a new screen on that subject appears. Table 2-4 lists all the screens that appear in the self-test.

+. TEST MENU OPERATOR SCREENS. SET CONTROLS CONTROL INPUTS MONITOR TEST PATTERNS SET TIME ace r DISABLE BROKEN CONTROLS SPECIAL FUNCTIONS.

SOFTWARE VERSION 2:

COPYRIGHT ATARI GAMES 1985

Figure 2-4 Test Menu Screen

2-4 Hard Drivin’ Compact

Operator Screens

Choose the operator screens in the test menu by turning the key while the words Operator Screens are in white. (For information about moving and choosing in the menu, see the section above.) If you are in the operator screens and want to go to the attract mode, first turn the key to go through the remaining operator screens. When you return to the test menu, turn off the self-test switch. These are the screens in the operator screens submenu:

Coin Options

Game Options Game Statistics Histogram of Game Times Error Count Games Played by Day and Hour Py .

The coin options appear in the first operator screen (see Figure 2-5). To move and choose in this screen, do the following: e To move up or down the list, press the right or left coin switch. © To change a setting, press the abort button and either coin switch, e To return to the setting originally on the screen, press the abort button and twrn the key at the same time. e To exit the screen, turn the key.

Coin Mode 3.cains 1 credit igi pl : 4 coin counts as 1 coin Left Mech Multiplier 1 coin counts as 1 coin, Bonus Adder: No Bonus Adder

‘Hit LEFTIBIGHT ¢: ‘Hold ABORT: and hit coin switches to cycte through choices Hold down ABORT and turn key to restore original setting Just turh key to save this setting and exit switches to move UP/DOWN.

Figure 2-5 Coin Options Screen

You can change an option when it is enclosed in a blue box. The default setting of each option is green. The other settings are blue when you select that option. The possible settings are shown in Table 2-2.

Page 17

Hard Drivin’ Compact

Table 2-2 Coin 1 Option cia Self-Test

Table 2-3 Game Option Settings

The coin options are explained below. Coin Mode is the number of coins required for one credit. © Right Mech Multiplier is the number of coins each coin counts as in the right coin mechanism. e Left Mech Multiplier is the number of coins each coin counts as in the left coin mechanism. e Bonus Adder lets you choose bonus coins, no bonus, or free play.

Game Options

Use this screen to set the game difficulty and various other operator options explained below. The screen is shown in Figure 2-6, and a table of the options is shown in Table 2-3. To move and choose in this screen, do the following:

pa GAME OPTIONS: ame DIFFICULTY | . MEDIUM. CHAMP LAP QUALIFICATION STEERING DURING ATTRACT MODE STEERING WHEEL FORCE ‘MEDIUM. HIGH: SCORE NAME CENSOR -ASYGOING CLEAR HIGH SCORE TABLE ‘CLEAR EVERY 2 WEEKS: SIGNS AND GAUGES. MILES PER HOUR.

HIT LEFT/RIGHT COIN SWITCHES TO MOVE UP/DOWN. HOLD DOWN ABORT AND TURN KEY TO RESTORE ORIGINAL SETTING JUST TURN KEY. TO SAVE THIS SETTING AND EXIT.

Figure 2-6 Game Options Screen e To move up or down the list, press the right or left coin switch. e To change a setting, press the abort button and either coin switch. e To return to the setting that was originally on the screen, press the abort button and turn the key at the same time. e To exit the screen, turn the key. You can change an option when it is inside a blue box. The default setting of each option is green. The other settings are blue when the option is selected. (The other settings are white when the option is not selected.) e Game Difficulty sets the game difficulty for the drivers. The settings are shown in Table 2-3. The custom setting lets you choose the actual amount of time the players receive. We suggest you use the preset factory setting (easy, medium, hard, and very hard), not the custom setting. © Champ Lap Qualification sets the difficulty of qualifying for the championship lap. e Steering During Attract Mode allows you turn the movement of the steering wheel on or off while the simulator is in the attract mode. e Steering Wheel Force is the amount of force exerted by the steering assembly motor on the steering wheel. @ High Score Name Censor controls a program to censor names entered on the high score table. The program deletes letters in possibly objectionable words in the high score table.

2-5

Page 18

Self-Test Hard Drivin’ Compact

Table 2-4 Summary of All Screens Appearing in the Self-Test

tomated Self Test

Program RAM and I

Test Menu: Screens , ~~ Instructions for Test Menu:

Color Bars. Monitor Adjust ~ Noni

2-6

Page 19

Hard Drivin’ Compact Self-Test

Table 2-4 Spaiaaey of Sina Screens Appearing in the Seif- Test, Liianciahen Screen =<

Color RAM -

VRAM Shift Register Test

Main Board MSP Tests

MSP Verify Test “MSP Complete: Test

Main Board Controls

Pots: 8 Bit Pots: 12 Bit Steering Wheel

Send Force Sine Wave ~ Square Wave . Triangle Wave Closed Loop Test» Life Test Duart

Main Board ROM Checksums

Main Board ZRAM Tests

ADSP Board Tests ADSP RAM 2100 Test ADSP IRQs ROM Checksums Scope Loops = °° -. Seq Input Memory Reads

Seq Input Mem ADR Writes” Seq Output ADR Writes, Buf 1

Seq: Output Writes, Buf 1

“Seq Output Writes, Buf 2 ‘Seq Output ADR Writes, Buf 2 ~ Toggle MPAGE ” "Toggle XPAGE. Toggle BCON.

Sound Board Tests

Sound Board Self-Test Play Sounds Sound Board ROM Checksums® Sound Board Program RAMs

Sound Board Program ROMs

COMRAM © 320 RAM Test VRAM for Display Brors :

» tests for the steering wheel.

Use if the steering wheel doés fot wi

| Sends a sine wave force “Sends a square wave fore

Sends 4 force to the motor amplifier PCB to

vare not kept correctly,

"Tests the RAM on the ADSP PCB. © > ~ Tests the response of the 2100 integral

“Reads the sequential input memiory. “Writes to the sequential input memory.

“Use these tests if the ba 08 © “Tests the sound program RAM and ROM, CO] The 68010 tests the DRAMs.** Shows much the same information as the Control Shows the gas Pedal, ie pedal, Sand Not used.

ter 3 for information about their us Use this test as directed’ in the flowchart in Ch. ter

Use this test as directed in the flowchart in

For factory use only. Not used.

Use this test if the ADSP board fails the

Tests if the ADSP system can generate interrupts. Tests the graphic ROM on the ADSP PCB. shows hardware ‘diagnostic tests for the ADSP boat

‘ites to the Sequential Outpuc Mem ites the address to the ‘Sequential Output Mem ités the address to the Sequential’ Output Writes the address to > the Sect Output Me

hoose and hear game sounds.

s the sound PCB program RAMS. ‘ests the sound PCB program ROMS.

2-7

Page 20

Self-Test

  • Clear High Score Table cleats the high score table at the time chosen. You can choose not to clear the table, clear it now, clear every week, or clear every two weeks. If you choose clear every week or clear every two weeks, the table is cleared when the simulator is tured on after Wednesday midnight every week or every second week. Be sure your simulator clock is set correctly so the table clears at the right time. e@ Signs and Gauges allows you to choose whether the signs and gauges are displayed in kilometers or miles.

Custom Game Options This screen is shown in Figure 2-7. Choose Custom under Game Difficulty to see this screen. The Custom setting lets you choose the actual amount of time permitted for each lap.

Note Always try the preset Game Difficulty settings before you use the settings in the Custom game options.

CUSTOM OPTIONS INITIAL Timi 96 MEDIUM. FIRST EXTENDED TIME 46 MEDIUM SECOND EXTENDED TIME 46 MEDIUM EXTENDED TIME AFTER SECOND 46 MEDIUM

HIT LEFT/RIGHT COIN SWITCHES TO MOVE UP/DOWN. HOLD.DOWN ABORT AND TURN KEY TO RESTORE ORIGINAL SETTING. JUST TURN KEY TO SAVE THIS SETTING AND Exit

Figure 2-7 Custom Game Options Screen.

In addition to the custom time settings, the times for the easy, medium, hard, and very hard game difficulty settings are also shown in the custom option. For example, if you have chosen the medium setting in Game Difficulty, then the custom screen appears as shown in Figure 2-7. To move and choose in this screen, do the following: @ To move up or down the list, press the right or left coin switch. To change a setting, press the abort button and either coin switch. @ To return to the setting that was originally on the screen, press the abort button and turn the key at Hard Drivin’ Compact

the same time. @ To exit the screen, turn the key. You can change an option when it is inside a blue box. The default setting of each option is green. The other settings are blue when the option is selected. (The other settings are white when the option is not selected.) All of the possible settings are shown in Table 2-5. The custom game options are explained below.

Table 2-5 Custom Game Option Settings

Option Initial Time

Second Extended Time

Extended Time

After Second

© Initia! Time is the amount of time always given for one driving session. @ First Extended Time is the amount of time given if the driver crosses the finish line before the initial time is up. ® Second Extended Time is the amount of time given if the driver crosses the finish line before the time is up on his second lap. e Extended Time Afier Second is the amount of time given when the driver crosses the finish line before the time is up after the first two laps.

Statistics

The statistics screen is shown in Figure 2-8. The statistics are coilected from the last time the statistics screen was cleared. Write this information on the statistics sheet in the back of this manual to help you maximize your profit. To move to the neat screen, just turn the key. To clear the statistics, press the abort button and turn the key at the same time.

Page 21

Hard Drivin’ Compact

STATISTICS LEFT COINS

ACTIVE MINS: - -420 XTNDED PLAYS: 14.

TOTAL GAME

LAPS BY TRACK:412667
XTENDED PLAYS BY TRACK: 03a42:
NO.X GAMES BY TRACK:01617

‘CHAMP LAPS 56° WINS 42 WSTRPLS--94 RPL ABORTS- 49° RPLSECS 257 TOTAL CREDITS: 123

HOLD ABORT AND TURN KEY TO'CLEAR STATISTICS JUST TURN KEY FOR HISTOGRAMS.

Figure 2-8 Statistics Screen

The statistics that the simulator collects are explained below. e Left Coins shows the number of coins counted in the left coin mechanism. © Right Coins shows the number of coins counted in the right coin mechanism. Aux Coins shows the number of times the auxiliary coin switch (inside the coin door) is pressed. e Idle Mins shows the number of minutes the simulator has been idle. © Active Mins shows the number of minutes the simulator has been played. @ Xtinded Plays shows the total number of times drivers received at least one additional lap. « 1-X Games shows the number of times drivers crossed the finish line one time and did not complete a second lap. 2-X Games shows the number of times drivers crossed the finish line two times and did not complete a third lap. e N-X Games shows the number of times drivers crossed the finish line three times and continued to drive. Auto Games shows the number of times drivers chose the automatic transmission mode instead of the shifter mode. Error Count shows the number of errors counted in the erasable memory. If you have more than 75 errors, you should have your simulator serviced by a qualified service technician. Self-Test

Total Games shows the number of unique games played, regardless of how many additional laps each driver received. « Laps by Track is numbers of laps, completed or not, on each track. The first number is the common track at the beginning, before the driver chooses the stunt track or the speed track. The second number is the speed track and the third number is the stunt track. See the example after No X Games by Track for more information. Xtnded Plays by Track is the number of additional laps given to drivers if they complete a track before the time allotted. (These laps, when added together, are the same as the number of laps in Xinded Plays.) These additional laps do not need to be completed to be counted. The first number is the common track at the beginning, before the driver chooses the stunt track or the speed track. The second number is the speed track and the third number is the stunt track, Use this to find out which track drivers are choosing and driving well on. See the example after No X Games by Track for more information. e No X Games by Track is the number of times the drivers did not get extended games on either track. If these numbers are very high (in proportion to the Laps by Track statistic), then the Game Difficulty setting may be too hard. The first number is the common track at the beginning, before the driver chooses the stunt track or the speed track. The second number is the speed track and the third number is the stunt track. The following examples show how the Laps by Track, Xinded Plays by Track, and No X Games by Track statistics are counted, If a driver chooses the speed track and completed it before the time allotted, started driving the second lap on the speed track, but ran out of time, and did not put in any more coins, you would see the following Statistics:

Laps By Track020
Xtnded Plays by Track010
No X Games by Track000)

If a second driver chooses the stunt track and did not complete the track before time was up, his statistics are added to the first driver’s as follows:

Laps By Track021
Xtnded Plays by Track01ia)
No X Games by Track001

Champ Laps is the number of times drivers qualified to race a championship lap.

Page 22

Self-Test

  • Wins is the number of times drivers won championship laps. ® Inst Rpls is the total number of instant replays. If this number is very high, the drivers should probably be reminded they will be most successful if they drive the Hard Drivin’ simulator like a real car. © pl Abortis the number of times the drivers pressed the abort button to cut the instant replay short. e = Rpl Secs is the total number of seconds the simulator is in the replay mode. « Total Credits is calculated by multiplying the coins by the credit setting you chose in Coin Mode.

;

Histogram

Read the histogram screen frequently and record the numbers on the statistics sheet in the back of the manual. You should read and reset the screen frequently because if more than 256 driving sessions occur in any one time category, then the counts of all the time categories are divided by two, so the information remains proportionally accurate, but not numerically accurate. If you read the screen infrequently, it is likely that you will not have a true numerical count of the number of sessions because of the way the histogram numbers are handled. The screen appears in Figure 2-9.

Histogram of Gare Times

» 460-UP’ Hold ABORT and tura key to clear histosram dust turn key for hext screen Figure 2-9 Histogram Screen

To clear the histograms, press the abort button and turn the key at the same time. To move to the next screen, turn the key.

Error Count

This screen, illustrated in Figure 2-10, shows the error count on the PC boards. If you call Atari Game Customer Service, the numbers on this screen may help Customer Service personnel troubleshoot your problem.

2-10 Hard Drivin’ Compact

ERROR.COUNTS.

WATCH DOG RESET BUS ERROR: ADDRESS ERROR: ILLEGAL INST ERROR DIVIDE BY ZERO ERR CHK INST ERROR ‘TRAP ERROR. PRIV VIOL ERROR. GSP-HANDSHAKE ERROR BAD POLY BUFF ERROR MSP TIME OUT ERROR ADSP TIME OUT ERROR ‘GSP TIME OUT ERROR GENERIC ERROR. NMLERROR ‘SPUR EXPTN ERROR ILLEGAL ERROR CODE OoedgoodCoDR OOD OO

HOLD ABORT AND. TURN KEY TO CLEAR ERROR COUNTS: JUST TURN KEY FOR NEXT MENU.

Figure 2-10 Error Counts Screen

Games Played By Day and

Hour

This screen, illusirated in Figure 2-11, shows the number of games played every hour in each day. The information on this screen is correct only if the simulator clock is set correctly. (Check the clock time on the set Clock screen. If the time is incorrect, follow the instructions in the Set Clock section of this chapter to set the clock.) Write the driving time information on the statistics sheet in the back of this manual to help you maximize your profit. To clear the screen, press and hold the abort button and turn the key at the same time.

Games Played hy Day and Hour Mon Tue Wed Thu Fri Sat

aM. ON.

10, 0. 00, Rech ecey EFT t+ s+4

‘Hold ABORT and tuen Key to clear table Just turn key for self test menu

Figure 2-11 Games Played by Day and Hour Screen

Page 23

Hard Drivin’ Compact

Set Controls Screens

If you have problems with the brake, clutch, gas pedal or steering assembly use the Set Controls screens before doing any troubleshooting or repairs. These screens allow you to set the beginning and ending Points of the control input to the main PCB. Often, resetting these points solves the problem you have. If resetting does not solve the problem, then check the Control Inputs screea, described below.

Note The simulator must be on for at least 15 minutes before you use the Set Controls screen. If you do not wait this long, the brake may not initialize correctly.

If you repair a control, install a new board, or install a new control, go through the Set Control screens. The first screen of the Set Controls screens is shown in Figure 2-12.

Note If you take a control out of the simulator for or repair it, go through all the Set Controls screens after you replace it. If you do not, the simulator will not operate correctly.

INITIALIZE POT INPUTS

TAKE YOUR HANDS AND FEET. OFF ALL CONTROLS THEN TURN KEY

Figure 2-12 First Set Controls Screen

After you choose Set Controls, simply do what the screens say. You must reset all the controls after you start the screens. The first screen initializes all potentiometers in the simulator. The next screens initializes the limits for the steering assembly, and the gas, clutch, and brake pedals. The numbers on each screen are for factory use. Self-Test

Note To initialize the brake, step firmly on it. Do not stomp on the brake or gently press it. Either way sets the brake limits incorrectly and drivers will be frustrated when they use the brake.

Control Inputs Screen

Check this screen as part of your regular maintenance to be sure your controls are operating correctly. The Control Inputs screen is shown in Figure 2-13. If you have a problem with a control, first go through the Set Controls screens then check the results on this screen. If using the Set Controls screens does not solve the problem, check Chapter 3 for troubleshooting and repair information about the control. The following controls are checked on this screen.

CONTROL INPUTS GAS. CLUTCH

<i BRAKE FORCE

LCOIN RCOIN: AUXCOIN ABORT SWITCH

SHIFTER: 3 2 4

STEERING WHEEL FCE3 CENTER EDGE

Figure 2-13 Control Inputs Screen.

e The gas pedal and the clutch pedal lines show the voltage input from the pedal potentiometers to the A/D converter circuits on the main PC board. As you use a pedal, the line length on the screen changes, showing the change in the voltage input from the potentiometer. e The brake force line measures the force with which you press the brake, not the distance it moves. As you press harder on the brake, the line becomes shorter, showing the change in the voltage input from the strain gauge on the pedal. To get correct results for the brake force, the simulator must be on for at least 10 minutes. When the line is shortest, the input is 0 Volts. When it is longest, the input is 5 Volts. If the line length for the

Page 24

Self-Test

gas, brake, or clutch does not change, you have a problem with pedal. See Chapter 3. @ The left and right coin mechanisms, the auxiliary coin switch, and the abort switch are at the bottom of the screen. As you use the switches, the name of the part should change from blue to green. If it does not, check the switch, mechanism, and harness. e The shifter checks the switch at each gear position. Move the shifter into each gear, and the shifter position number should change from blue to green. If it does not, see Chapter 3 for troubleshooting and maintenance information. @ As you turn the steering wheel clockwise, the hexadecimal number should increase and change to zero once every turn. As you turn the wheel counterclockwise, the number should decrease. Every time the steering wheel passes the center position, the words center edge should change from blue to green, If the steering wheel numbers do not change or the words center edge never change to green, see the table Troubleshooting the Steering Assembly in Chapter 3 for more information.

Monitor Test Patterns

Use this item to see the thirteen screens for checking the video display, the color RAMs, the GSP, which controls the video RAMs (VRAMs), and the video output. To move through the screens, press the coin switches. ® Color Bars screen shows these colors from left to right: white, yellow, light blue, green, purple, red, blue, and grey. If the colors are incorrect, see your video display manual for adjustment procedures. e Monitor Adjust is used to set up the monitor. © Monitor Brightness checks the adjustment of the video display brightness. e@ Grey Scale screen shows a white line on the left, and a grey scale showing black on the left. e B/W Dots screen can be used to check convergence and focus. e B/W Grid screen, shows a black background and a white grid pattern to check convergence. The grid jines should be straight within 3.0 mm. If you need to adjust the convergence, see the video display manual included with the simulator. e@ Diagonal Lines screen can be used to check video display linearity,

2-12 Hard Drivin’ Compact

¢ Full Screen colors test the color purity of the color RAMs and the display. The test displays a grey, white, red, green, and then blue screen. Each screen should be a rectangle of color, with no curving at the corners and no lines in the raster. If it does not, see your video display manual included with the simulator for adjustment procedures. e Monitor High Voltage Test screens switch between a white screen and a grey screen. If the high voltage to the display is regulated properly, the sizes of the white and grey screens will differ about 3/4 inch. e Scrolling Test scteen checks the scrolling mechanism in the GSP.

Set Clock Screen

Choose this item if you want to set the clock, turn the clock on, of turn it off. The screen is shown in Figure 2-14. The clock should be set correctly so the statistics on the operator screen Games Played by Day and Time will be right. The time on the clock also determines when the high score table is cleared. If you set the Clear High Score Table option in the Game Options screen to clear every week or every other week, then the high score table is cleared the first time the simulator is turned on after Wednesday midnight.

EXIT. INC HOURS INC MINUTES INC SECONDS. INC-DAY INC MONTH INC. DATE INC: YEAR : FASTER CLOCK CLOCK OFF. DEC HOURS DEC MINUTES DEC SECONDS DEC DAY. DEC MONTH DEC DATE DEC YEAR SLOWER CLOCK START CLOCK

CALIBRATION: +000. SECS/MONTH 41:22:21 AM FRIDAY. NOVEMBER 22,1988:

Figure 2-14 Set Clock Screen

You may need to turn on the clock if the simulator has a program crash. Turn off the clock only if you plan to store the simulator more than six months. (The clock has a lithium battery that should last more than five years in normal use.) To turn off the clock, choose Clock Off on the screen. To turn on the clock, choose Start Clock from the menu. In about two seconds, the clock starts.

Page 25

Hard Drivin’ Compact

If the clock is losing or gaining time, then use Clock Faster or Clock Slower to adjust the calibration of the clock. Choose the item you need from the menu by using either coin switch. Change the setting by tuming the key until you see the correct time, The items on the clock menu are explained below. e Exit returns you to the test menu, Inc Hours changes the hour setting ahead. Inc Minutes changes the minute setting ahead. Inc Seconds changes the second setting ahead. Inc Day changes the day of the week (for example, Monday or Tuesday) setting ahead. Inc Month changes the month setting ahead. Inc Date changes the date setting ahead. Inc Year changes the year setting ahead. Faster Clock changes the calibration setting ahead. Each increase in the calibration setting makes the clock ran about 5 seconds faster per month. Clock Offturns the clock off. Dec Hours changes the hour setting back. Dec Minutes changes the minute setting back. Dec Seconds changes the second setting back. Dec Day changes the day of the week (for example, Monday or Tuesday) setting back. Dec Month changes the month setting back. Dec Date changes the date setting back. Dec Year changes the year setting back. Slower Clock changes the calibration setting back. Each decrease in the calibration setting makes the clock run about 5 seconds slower per month. @ Star¢ Clock starts the clock.

Disable Broken Controls Screen

Use this screen, shown in Figure 2-15, if you have a broken shifter, brake pedal, or clutch pedal, and cannot repair it immediately. Before you disable a control, first try the Set Controls screens to see if resetting the control limits fixes the problem. If that does not work, see the information about the control in Chapter 3. Disable a control onlyas a temporary measure so you can continue to operate the simulator. if you disable a control, the realistic driving feel of that control is lost. Earnings could drop. Self-Test

DISABLE BROKEN CONTROLS MENU [SHIFTER L.::... WORKING... BRAKE WORKING CLUTCH WORKING

Hit LEFT/RIGHT Coin Switches to move UP/DOWN Hold ABORT and hit Coin Switches to cycle through choices Hold ABORT and turn key to restore orginal setting Just turn key to save this setting and exit

Figure 2-15 Disable Broken

If you have disabled a control, remember to choose working after you repair it.

Special Functions Screens

Use the items on this screen, shown in Figure 2-16, ifa system or board failed the program RAM and ROM test; if a board and microprocessor failed the automated self-test; if you have problems with the steering wheel; or if the clock settings or the statistics are erratic. A short summary of when to use these items is shown in Table 2-6. The Special Functions items are explained beiow. e Z£xifreturns you to the test menu. Main Board GSP Tests should be used if you get the message Bad GSP VRAM or Bad GSP Color RAM in

SPECIAL FUNCTIONS MENU

EXIT MAIN BOARD GSP TESTS. MAIN BOARD MSP TESTS MAIN. BOARD CONTROLS MAIN BOARD ROM CHECKSUMS MAIN BOARD’ ZRAM TESTS ADSP BOARD TESTS. ‘SOUND BOARD TESTS

Figure 2-16 Special Functions Screen

2-13

Page 26

Self-Test Hard Drivin’ Compact

em “Main Board GSP Tests”

Main Board MSP Tests Main Board Controls:

Main Board ROM Checksums Main Board ZRAM Tests

ADSP Board Tests

Sound Board Tests:

the automated self-test. This screen has six tests you can use.

e Main Board MSP Tests should be used if you get the message Bad MSP DRAM in the automated self-test. This screen has two tests you can use.

e Main Board Controls gives you most of the same information as provided in the Control Inputs screen plus other steering wheel tests. (All controls are “main board” controls.) ¢ Main Board ROM Checksums should be used if you get the message Bad Program ROM in the automated self-test. This tests the program ROMs individually and shows the results on the screen. e Main Board ZRAM Tests should be used if your controls settings are changing or erratic even though you used the Set Controls screen. Also use these tests if you suspect the simulator is not keeping the Statistics correctly. e ADSP Board Tests should be used if you get any message other than ADSP Board OK for the ADSP board test in the automated self-test. This screen has three tests and an ADSP ROM checksum test. It also has eight “scope loop” tests for factory use only. © Sound Board Tests should be used if you get the message Bad Sound Board in the automated selftest. However, many of the sound board tests are for factory use only.

Main Board GSP Tests

If the automated self-test reports bad VRAMs, choose Main Board GSP Tests and the screen in Figure 2-17 appears. First run the VRAM simple test. It gives the location of the bad VRAMs. If the VRAMs pass this test, but you think the simulator has a bad VRAM, run the VRAM verify test.

2-14 EXIT. VRAM SIMPLE TES’ VRAM VERIFY TEST: VRAM COMPLETE TEST: 11 MINUTES. TEST VRAM FOR DISPLAY ERRORS COLOR RAM. VRAM SHIFT REGISTER TEST.

Figure 2-17 GSP Tests Screen

VRAM Simple Test is the same test that is run in the automated self-test. It is run by the 68010 through the GSP interface and detects open or shorted address or data lines or missing parts. The results are displayed on-screen with a picture showing the VRAM section of the main PC board. The good parts are shown in green and the bad parts are shown in red. If an entire section appears in red, the problem may be with a buffer associated with that section, The test takes about 15 seconds. VRAM Verify Test is a complete memory test run by the GSP. The results are reported on the screen like in the simple test. The test takes about 90 seconds to run.

Since the verify test is run by the GSP program in the VRAMs, a single bad VRAM can cause the GSP Program to crash. When this happens, the 68010 microprocessor reports that all the VRAMs are bad, although probably only one VRAM is bad. You must run the VRAM complete test (described below) to find out which VRAM is bad.

Page 27

Hard Drivin’ Compact

if the VRAM verify test fails, but the VRAM simple test shows the VRAMs are good, you should run the VRAM complete test. If the verify test runs and reports that the VRAMs are good, then the VRAMs should be good. e VRAM Complete Test is a complete memory test run by the 68010 through the GSP interface. Because the 68010 runs the test, a single bad VRAM does not cause the test to report all the VRAMs are bad (as it does the verify test). Any VRAMs that are bad are shown on the screen at the end of the test. This test takes at least eleven minutes to run. e Test VRAM for Display Errors checks for video display problems. « Color RAM is the same test that is performed in the automated self-test. It tests the color RAM and reports the results. © VRAM Shift Register Test checks the shift register part of the video RAMs.

Main Board MSP Tests

Use this item if the MSP microprocessor fails the microprocessor and board tests that are performed by the automated self-test. When you choose Main Board MSP Tests the screen in Figure 2-18 appears. Run the MSP verify test, and if necessary, the MSP complete test.

MSP VERIFY TEST: 20 SECONDS MSP COMPLETE TEST: 2 MINUTES

Figure 2-18 MSP Tests Screen

The items in the MSP test screen are explained below. e Exit returns you to the test menu. MSP Verify Testtests the MSP DRAMs. Use this test if the MSP microprocessor failed the microprocessor and board tests. The test is run by the MSP program in the DRAMs so almost any DRAM problem causes an error message to appear on the screen. Self-Test

In 20 seconds, the test displays the results as a picture of the main PC board with the good parts shown in green, the bad parts shown in red, and the integrated circuits that are not DRAMs and not tested shown in blue. If two DRAMs are shown in red, then the problem could be the buffer associated with the pair. If this test does not isolate the MSP problem, then try the MSP complete test. © MSP Complete Test is run by the 68010 through the MSP interface. It tests the DRAMs and can detect nearly any problem that could develop. The test takes 2 minutes or longer, if it finds errors. The test displays the results as a picture of the main PC board with the good parts shown in green, the bad parts shown in red, and the integrated circuits that are not DRAMs and not tested shown in blue. If two VRAMs are shown in red, then the problem could be the buffer associated with the pair.

Main Board Controls

This screen provides some of the same information about the controls as is shown in the Control Inputs screen. The items on the screen are described below and shown in Figure 2-19. After you choose any item on this screen and go to that item, you can return to this screen by turning the key.

MAIN BOARD CONTROLS

EXIT: POTS: 8 BIT POTS: 12 BIT STEERING WHEEL DUART

Figure 2-19 Main Board Controls Screen

e ‘The Pots: 8 Bit screen has the same information as the Control Inputs screen. This screen appear in Figure 2-20. It shows the voltage inputs from the control. potentiometers to the A/D converter circuits. As you use a control, the line on the screen changes’ as the voltage input changes. If the line does not change, see the information about that control in Chapter 3.

2-15

Page 28

Self-Test

GAS CLUTCH

BRAKE FORCE

Figure 2-20 Pots: 8-Bit Screen

The Brake Force line shows the force on the brake pedal. As you push harder and harder on the brake, the line should disappear. 0 Volts appears as no line or a short line on the screen, and 5 Volts appears as a line halfway across the screen.

e Pots: 12-Bit screen is not used.

e Steering Wheel screen submenu is explained below and shown in Figure 2-21. e@ Duart does not apply to this simulator.

Steering Wheel Submenu

Use these iter if you have a problem with the steering assembly. The screen is shown in Figure 2-21. You will need to read the section Steering Assembly in Chapter 3 to find out how to use the tests. To move through the menu and the screens, use the coin switches, To exit a screen, push both coin switches down.

STEERING WHEEL

EXIT SEND FORCE ‘SINE WAVE SQUARE WAVE TRIANGLE WAVE CLOSED LOOP TEST. LIFE TEST

Figure 2-21 Steering Wheel Submenu Screen

2-16 Hard Drivin’ Compact

Exit returns to the Main Board Controls screen, Send Force sends a steady force to the motor amplifier PCB. See Figure 2-22. : SEND FORCE

PRESS INC TO INCREASE. POSITIVE FORCE PRESS DEC TO. DECREASE. POSITIVE FORCE HOLD KEY TO EXECUTE +0000. TO EXIT PRESS INC AND DEC AT THE SAME TIME

OPTO READ:

OPTO POSITION: 0000 0000

Figure 2-22 Send Force Screen

e Sine Wave sends a sine wave force to the motor amplifier PCB. This screen is similar to Figure 2-22. e@ Square Wave sends a square wave force to the motor amplifier PCB. This screen is similar to Figure 2-22. e Triangle Wave sends a triangle wave force to the motor amplifier PCB. This screen is similar to Figure 2-22, Closed Loop Test reads the steering wheel position and sends a force to the motor amplifier PCB to simulate a simple spring. e Life Testis a test for factory use only,

CAUTION Do not use the Life Test. It is used only in the factory.

Main Board ROM Checksums

This screen checks the main PC board program ROMs. for errors. Use this test if you have a bad program ROM message in the automated self-test or you suspect program ROM failure. To exit this screen, turn the key. When the checksum test is complete, a hexadecimal number follows each ROM as shown in Figure 2-23. The first two digits in each hexadecimal number can be any number, but the last two digits must be the ones shown in Figure 2-23.

Page 29

Hard Drivin’ Compact

PROGRAM ROM CHECKSUMS

ROMOHKKO2ROM OExx01

ROM1H. = xx04 ROM 12>: xx03 ROM 21. xx05, ROM SL xxXO7 ROM 4L xx09 ROM SL xxit ROM6L xxi3 ROM 77L xx15 ROM 2H xx06 ROM 3H xx08 ROM 4H Xx10 ROM SH Hx ROM 6H > xx14 ROM 7H xx16

Figure 2-23 ROM Checksums Screen

If the digits are all zeroes, the ROM is not on the board. Otherwise, if the last two digits are different than Figure 2-23, then the ROM is bad. Table 2-7 shows where the ROMs checked in this test are located on the main PC board.

Table 2-7 Program ROM Locations

Screen Main PCB Screen Main PCB

DesignationLocationDesignation Location
ROM 0H210 RROM OL200 R
ROM 1H2108ROM 1L200 $
ROM 2H210'TROM 2L200 'T
ROM 3 4210 UROM 31.200 U
ROM 4H210V>ROM4L.” . 200V
ROM 5 H210 WROM5L200 W
ROM 6H210%ROM 6'L200 X

ROM 7 H 210 ROM7L 200¥

Main Board ZRAM Test

This test checks the non-volatile RAM where the simulator statistics and control set-up values are kept. Check the ZRAMs if you think the statistics are incorrect. Also use this test if the control settings are changing even though you have recently set them with the Set Gontrols screens. If the simulator loses power or is reset while it is in this test, then the statistics and the control settings will be lost. If this happens, use the Set Controls item from the main menu to reset the controls. The statistics cannot be restored, Self-Test

ADSP Board Tests

Use this item if the ADSP PC board fails the microprocessor and board tests performed in the automated self-test. When you select ADSP Board Tests from the test menu, the screen in Figure 2-24 appears. The items on the screen are explained below.

EXIT. ADSP RAM 2100 TEST IRQ TEST ROM CHECKSUMS SCOPE LOOPS

Figure 2-24 ADSP Board Tests Screen

Exit returns to the test menu. ADSP RAM tests the memory on the ADSP PC board. The test takes a few minutes to run. It displays a picture of the ADSP PC board with the good parts shown in green, the bad parts shown in red, and the integrated circuits that are not RAMs and not tested shown in blue. If two RAMs are red, then the probiem could be the buffer associated with the pair. e 2100 Test checks the response of the 2100 integrated circuit on the ADSP PC board by copying data from one location to another using a 2100 program. @ IRQ Test checks if the ADSP can generate interrupts for the 68010. ROM Checksums tests the graphic ROMs on the ADSP PC board. When the checksum test is complete, a hexadecimal number follows each ROM as shown in Figure 2-25, on the next page. The first two digits in each hexadecimal number can be any number, but the last two digits must be the ones shown in Figure 2-25, If the last two numbers are different, then the ROM is bad or it is not on the board.

Page 30

Self-Test

ADSP ROM CHECKSUMS.

ADSP. 10k: xx01 ADSP-10K: xx02 ADSP. 10d: xx03 ADSP 10H: xx04

Figure 2-25 ADSP ROM Checksums Tests Screen.

© Scope Loops shows a menu with hardware diagnostic tests to be used with an oscilloscope. The tests are shown in Table 2-8.

Sound Board

Use these tests if the sound PC board failed the microprocessor and board tests in the automated self-test. If the sound PC board failed the test, select this item from the test menu and the screen in Figure 2-26 appears. Many of the tests require an oscilloscope and schematics. The tests are explained below. . © &xitreturns to the test menu. Play Sounds takes you to the Requesting Sound Screen. Follow the instructions on the screen to hear the simulator sounds. e Self-Test checks the sound program ROM and RAM, COMRAM, and 320 RAM. @ SD ROM Checksums tests the ROMs holding the SOUND BOARD.TESTS.

EXIT. LED TEST SELF-TEST PAC RAMP ‘SD ROM CHECKSUMS DAC 250 HZ PLAY SOUNDS SA COUNTER SB LATCH 320 TONE 320 1RQ 320 DAC RAMP 320 DAC ONES. 320:SBLOCK 320 SWEEP. 320 TUNE PROGRAM ROM PROGRAM RAM COMRAM 320.RAM

SOUND. SOFTWARE VERSION 3.0.

Figure 2-26 Sound Board Tests Screen

waveform data. The screen appears in Figure 2-27. It shows the ROM location, a hexadecimal number, and the results of the test for each ROM. The result will be one of the following: Ni--Nothing is loaded in that socket. No action is required. BAD--The ROM is bad.

OK—The ROM is OK. PROG DEV—The ROM is a program development ROM. 320 Sweep—Runs a program in the sound PC board 32010 to generate a sine wave sweep from 20 Hz to 9 kHz (requires oscilloscope). 320 Tune—Runs a program in the sound PC board 32010 to play a tune. Program ROM—Tests the sound PC board program ROMs with the sound PC board 68000 and reports the results on the screen.

Table 2-8 ADSP Scope Loop Diagnostic Tests

Test Function Seq Input Memory Reads

“Seq Input Mem ADR Writes Reads the sequential input mémory."The counters 9L, ~~ ed in a binary sequence fromm SRAO'to SRA15. ‘Writes to the sequential input memory:-‘The and 9H is incremented in‘a binary sequence Seq Output Writes, Buf 1

Seq Ourput Writes, Buf 2°

Seq Output ADR Writes, Buf 2

Toggle MPAGE |. Toggle XPAGE Toggle BCON ~. Writes to the Sequential Ourput “--and’4A are incremented in 4 bi "Writes the address 16 the Sequent MC, 4B, and 4A is incremented in “Writes the address to'the Sequential Seq Output ADR Writes, Buf 1

48, 4H, and 4] are incremented in 2’ binary. seq

‘The XPAGE at 6K, Pin 5, alternates between 0 and 1:

‘The BCON at 7K, Pin 7, alternates between 0-ai

2-18

Page 31

Hard Drivin’ Compact

SOUND BOARD TESTS. SOUND WAVE ROM CHECKSUMS.

O5AFFFENL
SSA1Fe2oK
4504FBOOOK
30A4313OK
20A5190OK
5A1F8s8OK
65CFD29NL
55CDFCOoK

45c 313B 30c 6A35. 20C FFFE 5C 76CB PROG DEV

Figure 2-27 Sound Board Sound Wave ROM Checksums Program RAM—Tests the sound PC board program RAMs with the sound PC board 68000 and reports the results on the screen. COMRAM—Tests the sound PC board communications RAM with the sound PC board 32010 and reports the results on the screen. 320 RAM—Tests the sound PC board 32010 program RAM with the sound PC board 68000 and reports the results on the screen. LED Test—Flashes the Test LED with the sound PC board 68000. DAC Ramp—Writes to every DAC value with the sound PC board 68000. The sawtooth frequency is about 60 Hz (requires an oscilloscope). DAC 250 Hz—Writes to every fourth DAC value with the sound PC board 68000. The sawtooth frequency is about 250 Hz (requires an oscilloscope). SA Counter—Creates an oscilloscope loop for the sound address counter (requires an oscilloscope). SB Latch—Creates an oscilloscope loop for the sound block latch (requires an oscilloscope). 320 Tone—Plays a sine wave tone created by the 32010 (requires an oscilloscope). 320 IRQ—Generates interrupts with the 32010 which the 68000 on the sound board recognizes (requires an oscilloscope). 320 DAC Ramp—The sound PC board 32010 ramps the DAC (requires an oscilloscope). 320 DAC Ones—The sound PC board 32010 writes walking ones through the DAC latch (requires an oscilloscope). 320 SBLOCK—The sound PC board 32010 writes increasing addresses to the Sound Block Latch (requires an oscilloscope). Self-Test

LEDs on the Main

PCB

The LEDs (light-emitting diodes) on the main PCB show you the status of various signals on the main PCB. Using the LEDs, you can check signals from various circuits going to the 68010 processor. The state of the signals is indicated by the LEDs which flash or stay lit. Figure 2-28 shows the location of the LEDs on the main PCB. Table 2-9 shows the possible status of the LEDs, with an explanation of what they indicate.

DIP Switches

If you try to enter the self-test, but nothing appears on the screen, use the DIP switch tests. Use the information from these diagnostic tests to help you find the: problem. Before you begin with these following tests, be sure that the problem is in the simulator hardware, not in the video display. If you have a completely dark screen, check the following: e Do you have power to the video display? e Are the video display’s filaments lit? e@ Do you have high voltage to the video display? If the answer to any of these questions is no, then you have a problem in the video display. Check the video display service manual included with your simulator for the suggested procedure.

2-19

Page 32

Self-Test

If you are sure that the probiem is not with the video display, then try the DIP switch diagnostics shown in Table 2-10, at the end of this chapter. These tests isolate various ICs and systems for troubleshooting. The results of the tests are indicated by the main PC board LEDs or on the video display screen.

To set the DIP switches for the tests:

  • Put a jumper across the DIAGN test points, shown on Figure 2-28.
  • Select the diagnostic test you want to use with the DIP switch settings.
  • Turn on the self-test switch, Hard Drivin’ Compact

4, Put a jumper momentarily across the RESET test points, shown in Figure 2-28.

To change to another DIP switch test:

  • Change the DIP switch settings.
  • Put a jumper momentarily across the RESET test points, shown in Figure 2-29.

To end the DIP switch testing:

  • Take the jumper off the DIAGN test points.
  • Put a jumper momentarily across the RESET test points. The DIP switch settings are om in the top position when the main PCB board is in the simulator.

Figure 2-28 DIP Switch and LED Locations on the Main PCB

2-20

Page 33

Hard Drivin’ Compact Self-Test

Table 2-9 LED Status

2-21

Page 34

Self-Test Hard Drivin’

Table 2-10 Using the DIP Switches

Purpose and Results

MSP P interface MsP ‘Auto Increment MSP’ Interrupts

MSP DRAM Verify

io perform | this test. 1=On; 0-Off: X=Doesn't Matt

2-22

Page 35

MAINTENANCE

&

TROUBLESHOOTING

Chapter 3

This chapter includes maintenance, repair, and troubleshooting information for your Hard Drivin’ Compact simulator. In the simulator, the hardware and software are closely related. If you are having problems with a mechanical assembly, always keep in mind that your electrical connections may not be good or you may have an electronic problem. To determine what kind of problem you have, always use the self-test screens as recommended for each part. ‘The first part of the chapter includes a schedule for j simulator maintenance and inspection, a table with general 4 troubleshooting information, and 4 a table of the voltage levels and test points on the PCBs. The rest of the chapter is arranged in alphabetical order by the name of the part or control. Under each part are maintenance procedures, troubleshooting tables and flowcharts, and repair procedures for the part.

If a part is mentioned, but not illustrated, refer to Chapter 4, J/ustrated Parts Lists, for information.

Page 36

Maintenance and Troubleshooting

Maintaining and Inspecting

Preventive maintenance includes inspecting, cleaning, lubricating, and tightening hardware. Perform the preventive maintenance regularly so you can keep the simulator in top condition, avoid problems, and maximize your earnings. Preventive maintenance tasks and intervals are shown in Table 3-1. Hard Drivin’ Compact

For the best performance from your Hard Drivin’ Compact simulator, maintain your simulator according to the times shown in Table 3-1. Instructions for performing these tasks is explained in the section about that control in this chapter. You may want to perform these tasks more often if the simulator is heavily used. Table 3-2 shows the correct voltage levels to various PC boards and the test points for those voltage levels. Low voltages to PC boards may cause problems with the controls, with the video display, or in driving.

Table 3-1 Maintenance and Inspection Items

Part When to Check ©

All Controls ~ Every month:

Coin Mechanism Every 6 months Pedals “Every 3 months Interior Components "Every 3 months Key Switch ~ Every 3. months

Shifter.©““, Every 3 months ~

Steering Assembly Every 2 months j ot L a + Bivbes settings: for belt wea: Put oil in the ball bearin;

PCBVoltageTest PointsSource and Purpose
Main -+5£01 VDC+5V2+5 :V Switching Power Supply
Main+1540.6 VDC+ 15V1"Regulated and supplied by the APU.PCB.
.poresheYE_ Used by the 12-bit A/D converter and ru

Main -22 VDC. -22V1 “Unregulated and supplied by the APU PC

etESRuns the -5V regalatot
Main+1240.5 VDC...+12V1~"Regulated and comes from the +15 vi

wena. ~ Used by the 12-bit-A/D converter and the ‘

MainBMDoeRegulated and comes from the
aoeeget"Used by the 12-bit A/D converter

ADSP. +5V1 or +5V2 eae and supp ied fror nth Sound oasv2

Sound 105B Pin 4

Sound “5 VDC.

Sound =. #SVDC.+5V2°

Sound“15 VDC2058 Pin 11,

APU +14VDC

APU -14VDC

APU -22VDC ~

APU+15VDC0s

3-2

Page 37

Hard Drivin’ Compact Maintenance and Troubleshooting

Table 3-3 Troubleshooting All Controls

Table 3-3 is the first of ten troubleshooting tables in this chapter. Use this table if all of your controls are acting erratically or not responding. if only one control is not working, go to the section about that control and read the troubleshooting information there.

Coin Mechanism

The coin mechanism should be cleaned every three months.

Maintaining the Coin

Mechanism

Tur off the power to the game. Open the upper coin door,

  • Open the gate on the door covering the magnet. Use the blade of a screwdriver to scrape away any metal filings collected on the magnet.
  • For a thorough cleaning, wash the coin mechanism in hot soapy water. Use a toothbrush to remove any stubborn build-up of residue in the coin path. 4, Dry the coin mechanism with compressed air.
  • If you do not want to use water, bush the loose dust off with a soft brush and scrub the residue in the coin path with a toothbrush. Blow all the loose dust and dirt out with compressed air.
Note Never lubricate the coin mechanism with oil or grease.

Dashboard

Generally you do not need to remove the dashboard to work on the controls. You can work on the key switch, shifter, and steering assembly without removing the dashboard. To remove these controls from the cabinet, see the section on that control for information.

Removing the Dashboard

  • Turn off the power to the game. Remove the three tamperproof screws and washer: in the cover plate of the steering wheel. Take of the steering wheel and cover plate. See Figure 3-l-
  • Open the back service panel. Remove the nuts o1 the six carriage bolts through the bottom of the cabinet shelf and push the carriage bolts through the cabinet shelf.
  • Also remove the nuts on the two carriage bolts through the front of the dashboard. These bolt have spring nuts on them and you cannot push them through the cabinet.
  • Disconnect the key switch harness, abort button harness, and shifter harness from the simulator ha ness.
  • In the front, remove the four low crown nuts ca the side carriage bolts. Remove the carriage bolts.
  • Take the dashboard off the game.

Installing the Dashboard

Put the dashboard on the cabinet. Push the har nesses through the cutouts,

  • Loosely install the carriage bolts and low-crown nuts on the sides of the dashboard.
  • Go to the back of the cabinet and install the fender washers and nuts on the carriage bolts on the front of the dashboard.
  • Insert the other carriage bolts through the bottom the dashboard and put the washers and nuts on them.
  • Connect the key switch harness, abort button harness, and shifter harness to the simulator harness.
  • Tighten the low-crown nuts on the sides of the dashboard.
  • Put on the steering wheel. Install the three tamperproof screws and washers through the center cover plate.

Interior Components All the components in the interior of the simulator should be cleaned every three months. This includes the PCBs, the power supply and the video display.

3-3

Page 38

Wintenance and Troubleshooting

tems Not Shown: | A046666-01 | ‘Start Harness Assy ‘A046667-01 Shifter Hamess Assy ‘A046668-01 | Abort Harness Assy

75-5528B Caniage Bolt

046655-01 ‘Strg Wahl Center Cover

046459-01 ‘Sirg Whl Decal .

75-055B Lock Washer 176025-4416 Tamperproof Screw 178099-005 Steering Wheel Hard Drivin’ Compact

175014-3050 Flat Blk Wshr 177024-0144 Low Crown Nut

160052-001

Switch Bezel 046621-01 Control Panel con bt t8e2 Contro! Panel Decal 75-55208 1/4 Black Carriage Bolt 177012111 Spring Nut 75-07002 Fender Wshr 177010-244 Lock Nut

‘A047000-01 Key Switch Assy 75-5112B 1/4 Carriage Bott 177010-244 ‘Lock Nut

75-5520B 1/4 Black Carriage Bolt Shifter Assy 75-5124B #10 Carriage Bolt 175014-1043 Flat Washer 177010-240 Leck nut

Figure 3-1 Removing the Dashboard

Cleaning the Interior Components Perform the following procedure to clean the componeats inside the cabinet.

  • Gpen the rear service door and the top service door.
WARNING Turn off the AC power, but do not unpiug the power cord before cleaning inside the cabinet. The power cord provides a ground path for static voltage that can be present on the cleaning tools.
  • Use a vacuum cleaner with a soft long-bristled brush attachment or use a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of the cabinet. Be sure to clean the power supply, PCB assemblies, and video display thoroughly.
CAUTION Be extremely careful when cleaning the electrical components inside the cabinet. Do not touch the electrical components with any solid object other than the soft bristles of the vacuum atiachment or paint brush.

Key Switch Assembly Table 3-4 lists what can go wrong with the key switch assembly.

Oiling the Key Switch Assembly Oil the key switch spring and shaft when turning the key switch becomes difficult, or when the key squeaks.

Page 39

Hard Drivin’ Compact

  • Tum off the power. Remove the back service door.
  • Remove the nuts and washers on the carriage bolts that hold the key switch assembly on the dashboard. Take the key switch out of the game.
  • Lightly oil the shaft and spring of the key switch. See Figure 3-2. Check that the spring is not broken. If it is, then replace the spring following the procedure under Repairing the Key Switch. 4, Replace the key switch in the dashboard. Put the nuts and washers on the carriage bolts that hold the key switch on the dashboard, Tighten the nuts.

Replacing the Spring in the Key Switch Assembly

If nothing happens when the key tums, and there is no resistance to tuming, you may need to replace the spring.

  • Turn off the power. Remove the back service door.
  • Remove the nuts and washers on the carriage bolts that hold the key switch assembly on the dashboard. Take the key switch out of the game,
  • Remove the retaining ring from the back of the key switch case. See Figure 3-2. 4, Loosen the socket-head screw on the brass actuator with a 5/32-inch Allen-head wrench.
  • Remove the other retaining ring inside the case. Pull out the key. Take out the brass actuator, the old spring, and the nylon washer.
  • Put lithium grease (Atari Games part no. 107029- 001) on the housing where it touches the shaft. Wipe off the excess grease.
  • Put one end of the spring into the hole in the side of the case.
  • Push the shaft back into the case far enough to mount the spring on the shaft. You may have to cut the legs of the spring to the correct length so that they do not interfere with the operation of the switch assembly.
  • Put the brass actuator into the case with the actuator pin facing the key and opposite the switch. Catch the free end of the spring under the pin. Maintenance and Troubleshooting

Push the actuator and the nylon washer onto the shaft.

  • Push the shaft through the case and install the two retaining rings. 11, Adjust the actuator on the shaft until it is parallel to the roller on the switch.
  • When the actuator is against the case opposite the switch, the key should be vertical. If the key is not vertical, turn it until it is. Tighten the screw on the actuator.
  • Use a piece of a manila folder or any other flat material about .015 inches thick to adjust the switch distance. Hold the actuator against the side of the assembly with the flat piece of material between the actuator and the switch. The switch should press against the material. Tighten the screws on the switch to hold it in place. Release the actuator. Check the setting. When you turn the actuator against the switch, the switch should click but not be pressed all the way to the switch body. 14, Replace the key switch in the dashboard. Put the nuts and washers on the carriage bolts that hold the key switch on the dashboard. Tighten the nuts.

Tightening the Screw in the Key Switch Actuator

If nothing happens when the key turns, and it turns more than 96°, you may need to tighten the screw on the actuator. 1, Turn off the power. Remove the back service door.

  • Remove the nuts and washers on the carriage bolts that hold the key switch assembly on the dashboard. Take the key switch out of the game.
  • Adjust the actuator on the shaft until it is parallel to the roller on the switch. See Figure 3-2. 4, When the actuator is against the case opposite the switch, the key should be vertical. If the key is not vertical, turn it until it is. Tighten the screw on the actuator.
  • Use a piece of a manila folder or any other flat material about .015 inches thick to adjust the switch

Table 3-4 Troubleshooting the Key Switch

_it-has no resistanc ) Key’ turns more that i Key turns, but nothing happens.

Page 40

Maintenance and ‘Troubleshooting Hard Drivin’ Compact

046450-01 176008-110 Items Not Shown: 107029-001 ‘Actuator #10 Sckt-Hd Screw 72020-0814 tum Grave _| 75-0408 Spring Pin #10 Split 175009-364 Lock Wshr Nylon Washer

178256-001 478001-004 Spring 1/2" Retaining Ring 1/2" Retaining

160045-003 Switch

NOTE: The switch is installed in the game rotated 180° from the position itis 1 shown in here. Housing

177010-232 #4 Hex Locknut 72-1412 +#4-40 Screw 75-0148, #4 Flat Wshr 046448-01 Key

Figure 3-2 Maintaining the Key Switch

distance. Hold the actuator against the side of the assembly with the flat piece of material between the actuator and the switch.’ The switch should press against the material. Tighten the screws on the switch to hold it in place. Release the actuator. Check the setting. When you turn the actuator against the switch, the switch should click but not be pressed all the way to the switch body.

  • Replace the key switch in the dashboard. Put the nuts and washers on the carriage bolts that hold the key switch on the dashboard. Tighten the nuts.

Replacing the Switch on the Key Switch Assembly Replace the switch if the key turns but nothing happens and the problem is not the spring, the actuator, or the connections. The key switch assembly is shown in Figure 3-2, 1. 2.

3-6 Turn off the power. Remove the back service door. Remove the nuts and washers on the carriage bolts that hold the key switch assembly on the dashboard. Take the key switch out of the game. 3. Remove the two Phillips-head screws that hold the snap-action switch on the key switch assembly. Take off the switch. Take the harness off the switch. Install the switch on the assembly, but do not tighten the screws. The roller on the switch should face the brass switch actuator. Loosen the screw on the brass actuator. Adjust the actuator on the shaft until it is parallel to the roller on the switch. When the actuator is against the case opposite the switch, the key should be vertical. If the key is not vertical, turn it until it is. Tighten the screw on the actuator. Use a piece of a manila folder or any other flat material about .015 inches thick to adjust the switch distance. Hold the actuator against the side of the assembly with the flat piece of material between the actuator and the switch. The switch should press against the material. Tighten the screws on the switch to hold it in place. Release the actuator. Check the setting. When you turn the actuator against the switch, the switch

Page 41

Hard Drivin’ Compact

should click but not be pressed all the way to the switch body.

  • Put the harness on the new switch. Connect the black wire to the C (or COM) terminal, and the white wire to the NO terminal.
  • Replace the key switch in the dashboard. Put the nuts and washers on the carriage bolts that hold the key switch on the dashboard. Tighten the nuts.

Pedals

The construction for all the pedals is very similar. The main difference is that the brake has a strain gauge and connector bonded to the pedal. The strain gauge transmits information about the force on the brake to the main PCB. The gas and clutch pedals use potentiometers to transmit position information to the main PCB.

If the Gas or Clutch Pedal

Does Not Work

Before you do any repairs, always perform the Set Controls screens in the self-test; then try the pedal to see if this corrects the problem. If that does not repair the problem see Table 3-5, Troubleshooting the Gas and Clutch Pedal and follow the flowchart in Figure 3-3. If you must repair the clutch, but you cannot do so immediately, disable the clutch circuit. (You cannot disable the gas pedal circuit.) if you disable the clutch circuit, drivers can only use the automatic transmission mode. To disable the clutch circuit, go to the Disable Broken Controls screen in the self-test and choose broken for the clutch, Disable the clutch only as a temporary measure, Repair the clutch as soon as possible since this is an essential part of the game. Maintenance and Troubleshooting

If the Brake Pedal Does Not Work

If you have problems with the brake, make sure the simulator has been on for at least 10 minutes. The brake may not work right if the simulator has not been on long enough. Before you do any repairs, always perform the Set Controls screens in the self-test but only after the simulator has been on at least 10 minutes. Try the brake to see if this corrects the problem. If that does not fix the problem, see Table 3-6, Troubleshooting the Brake Pedal, and follow the flowchart in Figure 3-5. If you decide you must check the strain gauge, follow the procedure in Testing the Brake Pedal Strain Gauge and Bonding section. If you must repair the brake, but you cannot do so immediately, and you want to continue to use your game, disable the brake circuit, When you disable the brake, a screen appears before each race which tells each driver that the brake does not work; if he wants to slow down, he should take his foot off the accelerator. To disable the brake circuit, go to the Disable Broken Controls screen in the self-test and choose broken for the brake. Disable the brake only as a temporary measure. Repair the brake as soon as possible, since this is an essential part of the game.

Greasing and Checking the

Grease the pivot shafts every three months with multipurpose white grease (Atari Games part number 178027-001).

  • Turn off the power to the simulator.
  • Take each pedal assembly out of the simulator. Remove the two button-head and two tamperproof screws and washers holding the assembly in the

Table 3-5 Troubleshooting the Clutch or Gas Pedal

Problem Pedal does not work or works erratically. YOR eee

Pedal does not retu

Pedal is wobbly.

  • Perform the Set Co . Follow the flowchar
Page 42

\aintenance and Troubleshooting Hard Drivin’ Compact

You have tried the SET CONTROLS screen. Go tothe CONTROL INPUTS screen in the selt-tes.

Do the ater ines , nine seen move Troubleshodtthe B21 AD stootiywhen bose circuit onthe main PCR, citer corti are opsratea?

(Check the ZRAM in SPECIAL. FUNCTIONS inthe sel-test. Repair

Repair

‘ste pote ; ‘slaledcorecty Repair ardis Be nut fig

(Check the voltage af the control input ‘o the main PCB. See the schematics,

Replace the otenitameter.

‘Toubleshoot the 8-bit ND circuit ‘on the main PCB.

Figure 3-3 Clutch or Gas Pedal Is Not Working or Is Working Erratically and You Have Tried the Set Controls Screens

Page 43

Hard Drivin’ Compact Maintenance and Troubleshootix

047211-01 Lower Link 177000-138 #8 Hex Nut 72-8816 #8-32 Sckt-Hd Screw 107027-001 Lithium Grease

\ 72-8810 #8 Skt-Hd Screw / 177000-138 #8 Hox Nut 99-215008 / 99-215009 Right-Wound Left-Wound ‘Spring / / Brake side hole pattern| Gas side hole pattern Spring

047210-01 047217-01 > Upper Link Butnper Sleeve << 047218-01 Aubber Bumper < i 175012-0125 119008-1001 Potentiometer

A047085-01 Brake Pedal Replacement Kit

82-8516B Button Hd Screw 175014-3050 ~ Flat Bik Wshr

Note When reassembling the\ links, set the upper link 22° clockwise irom vertical. Lo 176025-4416 Tamperproof NOTE: All parts not called out are Screw part of Front and Sides Assembly, 175014-3050 part number 171092-001. Fiat Blk Wshr

items Not Shown: A048669-01 Gas Harness Assy |

Figure 3-4 Maintaining the Brake and Gas Pedal Assembly

Page 44

Maintenance and Troubleshooting

cabinet. Unscrew the two screws holding the gas pedal to the floor if you are removing the gas and brake pedal assembly. See Figure 3-4 for the brake and gas pedals and Figure 3-6 for the clutch pedal.

  • Pull the assembly forward and disconnect the pedal harness(es ) from the simulator harness. 4, Put white grease on the pin holding the lower and upper links together. Work the grease around on the pivot shaft.
  • Check the parts of the pedal to make sure they are working correctly. Check and tighten (if necessary) the jam nuts on the links and the screw at the end of the pedal shaft. Tighten any other screws that have come loose.
  • Install the assembly in the cabinet. Attach the pedal harness to the simulator harness.
  • Instail the screws and washers.

Replacing a Pedal

Replace a pedal only if the pedal or the pedal shait is broken. If the pedal is wobbly, tighten the screw that holds the pedal in the pivot shaft.

Removing a Pedal

  • Turn off the power to the simulator.
  • Take the pedal assembly out of the simulator by removing the two button-head screws and two tamperproof screws and washers holding the assembly in the cabinet. Unscrew the two screws holding the gas pedal to the floor if you are removing the gas and brake pedal assembly. See Figure 3-4 for the brake and gas pedals and Figure 3-6 for the clutch pedal.
  • Pull the assembly forward and disconnect the pedal harness(es) from the simulator harness. Hard Drivin’ Compact

4, Remove the lower link if you are working on the clutch or the gas pedal.

  • Remove the hex-head screw that holds the pedal on the shaft. Pull off the pedal.
WARNING The springs will pop when you take off the pedal, Keep your fingers away from the springs.

Installing a Pedal If you are installing a brake pedal, do not install the pins in the connector or put the tie wrap on the pedal until the pedal is installed in the assembly. 1, Before you put the pedal in the assembly, turn the pivot shaft so the hole in the pivot shaft with the square cut-out around it is pointing towards the front of the assembly. See the detail in Figure 3-4.

  • Make sure the spring(s) are hooked over the spring afichor shaft. Hook a screwdriver through the springs from the back of the assembly to hold them in tension. This makes it easier to insert the pedal through the springs and into the hole in the pivot shaft. With the springs held in tension, insert the pedal into the pivot shaft. 3, Put the hex-head screw into the end of the pedal in the pivot shaft. 4, Grease the pin that holds the lower and upper links together.
  • Attach the lower and upper links together with the pin. Set the upper link so it is 22° clockwise from vertical.
  • If you have installed a brake pedal, put the tie wrap on the the pedal shaft to hold the wires in place. Table 3-6 Troubleshooting the Brake Pedal

Problem.” fake

ree

a

ND

Pedal is wobbly. Brake does not work or is working erratically. |» 1, Go through. the Set Controls sc wo Bad ; 3x “ ) Smust be onvat least 10-minut . Follow the flowchart in Figure 3: Check the brake force onthe Control in

. Check the strain gauge z and Bonding. a St . Check the voltage ‘level to . If the brake was not working, but now the brake is repaired; g¢ screen and choose working: Tighten the nut‘at the end of the pedal shai

Page 45

Hard Drivin’ Compact

‘You have tried the SET CONTROLS ‘screen. Go to the CONTROL INPUTS soreen in the self-test.

Does the BRAKE FORCE ine change when you ‘perate the ‘contro?

Call Atari Games Customer Service, Maintenance and Troubleshooting

‘Wait for 10 minutes.

Fix the ZRAM. the main PCB. Troubleshoot the &-bit AD circuit on ‘Check the connectors and wiring from the brake pedal te the main PCB.

Check the stain gauge and te strain

gauge bonding

Replace the fuse.

Figure 3-5 Brake Pedal Is Not Working or Is Working Erratically and You Have Tried the Set Controls Screens

Insert the pins into the connector.

  • Put the assembly in the game. Connect the pedal harness(es) to the simulator harness.
  • Install the screws and washers that hold the assembly in the cabinet.
Note Enter the seif-test and go through the Set Controls screens because you replaced the pedal. Otherwise the simulator will not work correctly.

Replacing a Spring

Replace the pedal spring(s) if they are weak, broken, or sprung.

  • Turn off the power to the simulator.
  • Take the pedal assembly out of the simulator by removing the two button-head and two tamperproof screws and washers holding the assembly in the cabinet. If you are working on the brake and gas assembly, remove the screws holding the gas pedal to the floor. See Figure 3-4 for the brake and gas pedals and Figure 3-6 for the clutch pedal.
  • Pull the assembly forward and disconnect the pedal harness(es) from the simulator harness.

3-11

Page 46

Maintenance and Troubleshooting

ps 107027-001 Lithium Grease

047211-01 Lower Link 177000-138 #8 Hex Nut

Screw

Clutch Side Hole Pattern

176025-4416 Tamperproof Screw 175014-3050 Flat Blk Wshr

99-215006 Clutch Pedal

NOTE: All parts not called out are part of the Front and Sides Assembly, part number 171092-001.

82-8516B Bution Hd Screw 175014-3050 Fit Bik Wshr 72-8810 +#8-32 Sckt-Hd Hard Drivin’ Compact

8721001 srsosnor2s 477000-138 Flat Washer #8 Hex Nut 72-8810 #8-32 Sckt- Hd Screw 119008-1001 Potentiometer 99-215009 Left-Wound

99-215008 Right-Wound Spring

Items Not Shown: A046671-01 Clutch Harness Assy

Figure 3-6 Maintaining the Clutch Pedal Assembly

  • Remove the lower link if you are working on the clutch or the gas pedal.
  • Remove the hex-head screw that holds the pedal on the shaft. Pull off the pedal.
WARNING The springs will pop when you take off the pedal. Keep your fingers away from the springs.
  • Take the pedal assembly off the front metal plate by removing the four nuts on the carriage bolts.
  • Remove the bumper shafts, spring shafts and support shafts, which hold the assembly together.
  • Replace the spring(s). If the pedal has two springs, replace both of them.

3-12 9, Lubricate the pivot shaft with multi-purpose grease before you put it back into the assembly.

  • Assemble the shafts in the pattern shown in Figure 3-4 for the gas or brake pedal or Figure 3-6 for the clutch pedal. If you have disassembled the brake pedal, be sure to put the large brake bumper and bumper shaft on the bottom.
  • Install the pedal assembly on the front metal plate with the four nuts and washers on the carriage bolts.
  • Before you put the pedal in the assembly, turn the pivot shaft so the hole in the pivot shaft with the square cut-out around it is pointing towards the front of the assembly. See the detail in Figure 3-4.
  • Make sure the spring(s) are hooked over the spring anchor shaft. Hook a screwdriver, or any other long thin piece of metal, through the springs from
Page 47

Hard Drivin’ Compact

the back of the assembly to hold them in tension. This makes it easy to insert the pedal through the springs and into the hole in the pivot shaft. With the springs held in tension, insert the pedal into the pivot shaft.

  • Put the hex-head screw into the end of the pedal in the pivot shaft. 15.If you are working on the clutch or gas pedal, grease the pin that holds the links together. 16, Attach the lower and upper links together with the pin. Set the upper link so it is 22° clockwise from vertical. Tighten the jam nut on the lower link on the pivot shaft.
  • Put the assembly in the game. Connect the pedal harness(es) to the simulator harness.
  • Install the screws and washers that hold the assembly in the cabinet,

Replacing the Clutch and

Gas Pedal Potentiometers

Do not replace a potentiometer until you have performed the Set Controls screens. Check to see if that solves the problem. If not, follow the flowchart in Figure 3-3 to make sure that the potentiometer is the problem.

  • Turn off the power and unplug the game.
  • Take the pedal assembly out of the simulator by removing the two button-head screws and two tamperproof screws and washers holding the assembly in the cabinet. Remove the two screws that hold the gas pedal to the floor of the simulator. See Figure 3-4 for the brake and gas pedals and Figure 3-6 for the clutch pedal.
  • Pull the assembly forward and disconnect the pedal hamess(es) from the simulator harness, 4, Take the wires off the potentiometer.
  • Loosen the jam nut on the upper link on the potentiometer shaft. Remove the upper link.
  • Loosen the 1/2-inch nut on the potentiometer shaft and remove the potentiometer.
  • Install the potentiometer so the key is in the key slot at the top, the terminals point to the back of the assembly, and the flat of the shaft is facing up.
  • Solder the wires onto the potentiometer in the order shown in Table 3-7.
  • Install the assembly in the simulator. Connect the pedal harness(es) to the simulator harness. 10, Now switch on the self-test and go through the Set Controls screens. Maintenance and Troubleshooting

Table 3-7 Pedal Potentiometers Harness Connections

Note Enter the self-test and go through the Set Controls screens because you repaired the pedal assembly.

Testing the Brake Pedal Strain Gauge and Bonding

If you have brake problems, see the flowchart in Figure 3-5. If necessary, do the following tests to check the strain gauge and strain gauge bonding.

  • Put an ohmmeter across pins 1 and 2 of the brake harness connector. If the ohmmeter does not measure 350 Q + 10%, the strain gauge is bad or the connection is bad. Replace the brake pedal and the strain gauge.
  • If the ohmmeter does measure 350 Q + 10%, then check the bonding. Attach a digital volt-ohmmeter to pins 1 and 2 and have someone press hard on the brake.
Note Use a sensitive ohmmeter to check the change in resistance since the change is only about 1 Ohm.

If the resistance does not change as the pressure on the brake pedal changes, then the bonding has failed and you must replace the brake pedal and the strain gauge.

Replacing the Brake Strain Gauge

If you have tested the strain gauge and are sure that the gauge or the bonding is bad, you must replace the brake pedal with the strain gauge already attached since special bonding techniques are required. Follow the steps in Replacing the Brake Pedal.

3-13

Page 48

Maintenance and Troubleshooting

Shifter Assembly

If you have problems with the shifter, check Table 3-8, Troubleshooting the Shifter Assembly. If you must repair the shifter, but you cannot do so immediately, and you want to continue to use your simulator, disable the shifter circuit. When you disable the shifter, drivers can only use the automatic transmission mode. To disable the shifter circuit, go to the Disable Broken Controls screen in the self-test and choose broken for the shifter. Disable the shifter only as a temporary measure. Repair it as soon as possible since this is an essential part of the simulator.

Tubsicating the Shifter

Turn off the power. Open the back service door.

  • Remove the shifter from the dashboard. Remove the nuts and washers on the four carriage bolts that hold the shifter, shifter spacer, and shifter bezel on the dashboard. Take off the shifter, spacer, and bezel.
  • Remove the six screws that hold the two halves of the shifter case together. See Figure 3-7. Carefully pull apart the case. The ball bearing can fly out since it is under compression. The spring will pop out too. 4, Lubricate the ball bearing under the shifter handle and the shifter pattern in the bottom of the shifter. Use light-duty white grease, Atari Games part number 178027-001.
  • Reassemble the shifter and shifter spacer.
  • Put the shifter, shifter spacer, and shifter bezel back on the dashboard and install the carriage bolts, washers, and nuts that hold them in place. You may need someone to help you.

Replacing a Shifter Switch

Before you replace a switch, check the shifter switches on the Control Inputs screen in the self-test. If a gear position number does not change from blue to green Hard Drivin’ Compact

when you move the shifter into that position, then probably the switch or the connection is bad.

  • Open the back service door. Check the connections to the shifter. See Table 3-9. If the connections are correct and tight, turn off the power. Remove the four nuts and washers that hold the shifter, shifter spacer and bezel on the dashboard. See Figure 3-7. Take out the shifter, spacer and bezel.
  • Make sure the shifter handle is not engaging the switch you are replacing. 4, Carefully remove the switch on the shifter so the actuator pin and spring above the switch do not fly off and are lost.
  • Replace the switch. Install the pin and spring.
  • Connect the harness to the switch with the wires in the order shown in Table 3-9.

Table 3-9 Harness Connections to the

Shifter Switches

  • Assemble the shifter and shifter spacer and install them in the dashboard.
  • Reassemble the shifter and shifter spacer.
  • Put the shifter, shifter spacer, and shifter bezel back on the dashboard and install the carriage bolts, washers, and nuts that hold them in place. You may need someone to help you.

Speakers

If you have problems with a speaker, check Table 3-10, Troubleshooting the Speakers, before you replace it.

Table 3-8 Troubleshooting the Shifter Handle moves, but the s]

Check if, switches are broken Check if the return plu broken:

3-14

Page 49

Hard Drivin’ Compact Maintenance and Troubleshooting

75-5124B #10-24 Bik Carriage Bolt 4 178027-001 ‘age oN Lithiurn Lubricant 005255-02 Shifter Bezel

039154-01

4000610-02 Handle Assy ~

039705-01 ‘Compression Spring

178219-001 3/8" Ball

177010-240 000609-02 #10-24 Locknut Housing 175014-1043 Flat Washer

043711-01 Return Spring

17010-2532 72-JB3606 > 94.49 Hox Nut 53-00- #6-19 Hex tens001 Wshr-Hd Screw 72-14128 043712-01 #4-40 X-Rec Screw ‘Switch Spacer

Figure 3-7 Maintaining the Shifter Assembly

3-15

Page 50

Maintenance and Troubleshooting, Hard Drivin’ Compact

Table 3-10 Troubleshooting the Speakers

Problem Solution No sound Make sure the volume is turned-up: If the volume is turned up, do

Check the voltage level to the sound P Check the witing, ~ Replace the speaker i ©If none of the abo the main PCB...

Removing a Speaker

  • Turn the power off. Remove the back service door. 2, Disconnect the connectors from the speaker that is bad. Remove the screws that hold the speaker in the cabinet.
CAUTION Be careful when handling the speaker. The cone material is fragile and can be easily damaged.
  • Remove and replace the speaker.
  • Connect the speaker to the simulator harness. Make sure you attach the connectors correctly. The signal wire should be attached to the speaker terminal marked by color,a “+” sign, or a round dot. (The signal wire is indicated on the simulator wiring diagram in the Schematic Package.)

Static-Sensitive Devices

Devices

Be careful when you work with static-sensitive devices on the simulator PCBs. These devices can be microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology.

Replacing Static-Sensitive

The static-sensitive devices can fail from a static charge that has built up in your body. They can also fail be-

3-16 cause of leakage from an improperly grounded soldering iron. Before you handle a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an object that is earth-grounded. If you solder a static-sensitive device, use a soldering iron with a propeily grounded three-wire cord. Before you replace a static-sensitive device, make sure that the device actually is defective. A static-sensitive device can appear defective due to leakage on a PCB. To check if a device is defective, ground any static voltages as described in the paragraph above. Clean both sides of the PCB with flux remover or an eraser. For discrete FETs, clean thoroughly between the gate, drain, and source leads. Then test the device. A new static sensitive device may be packaged in conductive foam or may have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it to a PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.

Steering Assembly

If you have problems with the steering assembly, check the troubleshooting suggestions in Table 3-11. Always perform the Set Controls screens in the self-test first. You should regularly go through the Set Controls screen to adjust the set points on the steering assembly to account for wear on the belt.

Oiling the Bronze Bearing

The only bearing on the steering assembly that must be oiled regularly is the bronze pillow block bearing behind the steering wheel. See Figure 3-9.

Page 51

Hard Drivin’ Compact Maintenance and Troubleshooting

Table 3-11 Troubleshooting the Steering Assembly

the Steering Wheet numbers do not change the optical reader:

and the centering disk is scraping agains!

the words Center Bdge do’not chan; blue to‘green, And the steering is erratic. "* the words Ginter Bilge do not‘ blue to green, and there is no steering powel 1

the words Center Fdge do not chang from and the centering disk is seraping against Steering hi has no or for

blue to green,

the optical caer

Steering wheel is not centered oly, eS ne ©The centering disk is bent. R

‘The ‘centering PCB or:conne or 3 the-connection, replace . eae he centeriny Pt

  • Take off the back service door.
  • The bearing fill hole is on the right. Use an oil can with a flexible spout and put oil in the bearing.

Adjusting the Steering Belt

The belt itself cannot be adjusted, but the limits of the steering moyement can be changed to adjust for belt wear. You should do this every two months by going through the Set Controls screens. If the belt is very loose and resetting the set points does not improve the steering, then replace the belt.

Replacing the Steering Belt

Replace the belt on the steering assembly if it is broken or loose, However, before you replace the belt because it is loose, use the Set Controls screen to see if this will fix the problem. By resetting the steering limits on this screen, you can adjust the outputs to compensate for wear in the belt. i. Turn off the power to the simulator. Take off the back service door.

  • Remove the belt by pushing the motor towards the steering wheel mounting shaft and working the

3-17

Page 52

Maintenance and Troubleshooting Hard Drivin’ Compact

72-5432 3/8-16 x2" 177010-248 — s75914-1070 Hex Bolt SIE Lock Nut \ 7746 Fe Wehr

046652-03

  • 1/4" Spacer 475014-1063 Spee, 77010248 38 FIL Wshr 041787-02 5/8" Spacer 3/8 Lock Nut 106007-001 Encoder Disk Adhesive ee 178012-010 i 1" Cip Ring

178268-001 Ball Bearing

+#6-32 Hex Wshr

046650-02

046647-01 Pe 8-880 CB Mag Brkt

#8 SKVHd Screw 75-D48S #8 Split-Lock Wshr 175014-1032 72-CT604 #8 Fit Wshr +#6-32 Hex Wshr Hd Screw

haat Aoageo1-01 72-5416 / Centering Disk | Hex Bolt Coley Centering Disk Items Not Shown: CB Assy

72-8406 043807-02 #4-40 Sckt-Hd Screw | Centering Disk 75-044 #4 Split-Lck Wshr 046644-01 Stig Whi Mtg Steering Wheel and Shaft Mounting Hardware

176022-3806 #8-32 SktHd Screw 046459-01 Strg Whi Decal 046655-01 Strg Wh! Center Cover 178025-a416 1/4-20 Bik Tamperproof Screw 178089-005 Steering Wheel 75-055B 1/4 Bik Uck Wshr

Figure 3-8 Steering Assembly, Front View

Page 53

Hard Drivin’ Compact Maintenance and Troubleshooting

107013-001 Oil 178269-001 Bronze Bearing 107013-001 Oil ‘046665-01 Motor-Opto Harness Assy 72-CT604 046648-01 Disk Stffening - #6-32 Hex Wshr Hd Screw

A046689-01 Encoder Disk PCB Assy

106007-001 Penetrating Adhesive

/ 178270-002 6 Pulley

72-5416 9/8-16 x 1" Hex Ameer 0a6: Bott Pulley V-Belt anads74-o1

Motor Assy 175014-1077 V2 Fit Wshr 178012-006 046645-01 1/2" Clip Ring Pivot Shatt 178270-003 2" Pulley

Figure 3-9 Steering Assembly, Rear View

belt off the pulleys. See Figure 3-9.

  • Install the new belt by pushing the motor towards Note the steering wheel mounting shaft and putting the You must enter the self-test and go through belt on the pulleys. the Set Controls screens because you re-
  • Put oil in the fill hole on the bronze bearing on the paired the steering assembly. Otherwise the steering wheel mounting shaft if you have not simulator will not work correctly. done this in the last three months.
  • Replace the back service door.
Page 54

Maintenance and Troubleshooting

‘The steering wheel tus continuously during game play and you have aready ‘vied the SET CONTROLS screen

‘CONTROL INPUTS screen, does the wheel pasion no increase ‘smoothly as you tur the wheal clockwise? Does the poston 1, Lbeoome zero once ove 360" un? {wo staring wheel postion pas ‘on the main PCB, Does ine input switch am 0 10 8Y and back Hard Drivin’ Compact

‘Check he steering whee! harness. Chack te steering whee! encoder and centering asks and PCBs,

Goto the MAIN BOARD CONTROLS screen ‘and choose the STEERING WHEEL menu. ‘Choose the TRIANGLE WAVE Test, Troubleshoot the optical postion circuit ‘on the main PCB. See the main PCB schematic.

‘Doss the — tong wel ors Check the motor amplifier PCB fuse and the huge nei ton coc No | cable tom the main board tothe motor ter cocise when os i do he THANGLEWAVE Tet? Hol Arp aseoolh C art ily Check the motor amp PCB.

Call Atari Games Gustomer Service.

Figure 3-10 The Steering Wheel Continuously Turns in One Direction and You Have Tried the Set Controls Screens

Replacing the Steering

Motor

Replace the steering assembly motor if you have followed the flowchart in Figure 3-10, 3-12, or 3-13 and you are sure that the motor is the problem. Another reason to replace the motor is if the steering wheel is difficult to turn and the problem is not lubrication or the mechanical parts. Before you replace the motor, check the harness connections to make sure they are good.

Removing the Motor

  • Turn off the power to the simulator.
  • Remove the three tamperproof screws and washers

3-20 w in the cover plate of the steering wheel. Take off the steering wheel and cover plate. See Figures 3-8 and 3-9. Take off the back service door. Disconnect the steering assembly harness from the simulator harness. Disconnect the motor power from the motor amplifier PCB assembly. Remove the screw down tie wrap from the side of the cabinet. Remove the four nuts that hold the steering assembly on the shelf. Push the screws through holes in the shelf. Remove the steering assembly. Remove the harness from the encoder PCB. Take off the two screws that hold the encoder PCB on the assembly. Remove the PCB.

Page 55

Hard Drivin’ Compact

. Remove the encoder disk, disk collar, and disk stiffening ting by loosening the socket-head screw on the disk collar. . Remove the belt by pushing the motor towards the steering wheel mounting shaft and working the belt off the pulleys. . Remove the pulley on the motor by loosening the socket head screw that holds it on. (The sockethead screw has a penetrating adhesive on it.)

  • Remove the nui and hex-head bolt that holds the spring in tension.
  • Take off the 1/2-inch retaining ring at the front of the motor on the pivot shaft.
  • Pull the pivot shaft out the back of the steering assembiy. Remove the motor.
  • Remove the four socket-head screws and washers on the front of the motor.

Installing the Motor 1. Install the pivot plate on the front of the motor. Align the bottom of the pivot plate with the bottom flat edge of the motor bezel. Install the four socket-head screws with the splitlock washers and flat washers that hold the pivot plate on the motor. Tighten the screws to 30 + 5 inch-pounds. Put the motor and pivot plate in the assembly with the labei and harness on top. Push the pivot shaft through the frame, washers, motor, and pivot shaft as shown in Figure 3-11. Install the 1/2-inch retaining rings on the ends of the pivot shaft as shown in the figure. Assemble the hardware that holds the spring in Maintenance and Troubleshooting

Steering Frame

Figure 3-11 Installing the Steering Pivot Shaft

tension. See Figure 3-8. Install the parts on the bolt in the following order: 1, 1/4-inch-long spacer. Hook the end of the spring around this spacer.

  • Washer.
  • 5/8-inch-long spacer. 4, Washer.

Table 3-12 Torque Te Table for the Screws on the Steering Assembly “Screw.

Holding the encoder PCB to the mounting bracket“!

Holding the ¢entering PCB to the frame f Holding the pillow block bronze bearing'to the fra Holding the pillow block ball bearing to the frame ~ Holding the encoder PCB bracket to the frame: Holding the extension spring hardware On the fram

  • pulleys on the shaft.

Holding the centering disk to the disk stiffening ring — Holding the pivot plate to the motor Holding the encoder disk collar on the shat

Holding the'‘steering wheel-on the’

3-21

Page 56

Maintenance and Troubleshooting

‘Steering wheal is very erky and you have already tried the SET CONTROL soreen,

‘CONTROL INPUTS screen, does the whe! positon no, increase ‘smoathy as you tum me whee! clock= Treasure the wolage onthe no steering wheel poston inputs ‘onthe math PCB, Does he input ‘ston rom9 to 5V and back when you tun the steering wneel? Hard Drivin’ Compac.

Check steering wheel harness, Check. stesring wheel encoder and centering disks and PCBs.

Go to the MAIN BOARD CONTROLS screen. ‘and choose the STEERING WHEEL tem. ‘Choose the SEND FORCE Test from the” eubmert schematic. ‘Troubleshoot the optical postion circu, on the main POB. See he main PCB

Gc to the MAIN BOARD CONTROLS screen

nd go into te steering whee! menu

‘Choose the TRIANGLE WAVE Tesi.

Call Atari Games Customer Service, ‘Check the motor amp PCB. ‘Check the motor amplifier PCA fuse and the ‘cable from the main board to the motor amplifier assembly.

Figure 3-12 The Steering Wheel Is Jerky and You Have Tried the Set Controls Screens

  • Install the bolt with the hardware on the outside of the frame. Put the lock nut on the bolt inside the frame and tighten it to 212 + 20 inch-pounds.
  • Remove the socket-head screw from the pulley you took off the motor. Put a penetrating adhesive on the screw.

Slide the pulley back on the motor shaft. Align this pulley to the other one. Turn the pulley so the screw hole is over the flat of the shaft. Install the socket-head screw. Tighten the screw to 50 + 8 inch-pounds. Install the belt on the pulleys.

3-22 7. Put oil in the fill hole on the bronze bearing on the steering wheel mounting shaft if this has not been done recently. Remove the screw from the disk collar. Put the encoder disk, collar, and stiffener on the motor shaft. Make sure the hole for the socket-head screw is facing out and is over the flat of the shaft. Put on the encoder PCB, Make sure the optical readers and the harness connection face down. Move the encoder disk so it is between the two readers, but does not touch them. Tighten the screws on the encoder PCB to 10 + 3 inch-pounds.

Page 57

Hard Drivin’ Compact

  • Install the screw that holds the disk collar on the shaft and tighten it to 30 + 5 inch-pounds, Make sure the encoder disk does not move on the shaft.
  • Install the harness on the encoder PCB,
  • Before you install the steering assembly back in the simulator, turn the centering disk so the single hole in the disk is between the optical readers on the PCB. This will make it much easier to correctly install the steering wheel. in
  • Put the steering assembly back in the cabinet. Install the four carriage boits through the holes in the shelf. Tightly install the fender washers and nuts on the bolts so the assembly does not move.
  • Install the steering wheel with the center spoke down. Make sure the single hole on the centering disk is between the optical reader on the centering PCB so the steering wheel will be correctly centered. Put the center cover on the steering wheel. Install the three tamperproof screws and lock washers that hold the steering wheel on the steering assembly. Tighten the screws to 50 + 8 inch-pounds.
  • Connect the steering assembly harness to the simulator harness. Attach the screw down tie wrap on the motor-opto harness to the cabinet. Make sure the wires will not be caught in the motor pulley. Connect the motor power harness to the motor amplifier PCB. 16, Install the back service door.
Note You must enter the self-test and go through the Set Controls screens because you repaired the steering assembly. Otherwise the simulator will not work correctly.

Replacing the Encoder or Centering PCB

If you are having problems with the steering, and you have determined the problem is the encoder or the centering PCB by following the troubleshooting table, Table 3-11 or the flowchart in Figures 3-10, 3-12, or 3- 13, then replace the PCB. If you are replacing the centering PCB assembly on the steering wheel shaft, part number 046691-01, you can replace it with the another centering PCB assembly or with the encoder PCB assembly, part number A046689-01. However, you must replace the encoder PCB assembly with an encoder PCB assembly, part number A046689-01. Maintenance and Troubleshooting

Removing the Encoder or Centering PCB

Turn off the power to the simulator.

  • Remove the three tamperproof screws and washers in the cover plate of the steering wheel. Take off the steering wheel and cover plate. See Figures 3-8 and 3-9.
  • Take off the back service door. Disconnect the steering assembly harness from the simulator harness. Disconnect the motor power harness from the motor amplifier PCB assembly. Remove the screw down tie wrap from the side of the cabinet. 4, Remove the four nuts that hold the steering assembly on the shelf. Push the screws through holes in the shelf. Remove the steering assembly.
  • Remove the harness from the PCB you are replacing.
  • Take off the two screws that hold the PCB on the assembly. Remove the PCB.

ee the Encoder or Centering PCB

Put the new PCB in place. However, do not screw it down until you check thar the disk is between the optical readers and not touching either one. If the disk is not centered between the readers, loosen the socket-head screw on the disk collar and move the disk until it is centered. Tighten the screw to 30 + 5 inch-pounds to hold the disk in place. Tighten the screws that hold the PCB on the frame to 10 + 3 inch-pounds.

  • If you have not regularly oiled the bronze bearing on the steering wheel mounting shaft, put oil in the fill hole on the bearing.
  • Instail the harness on the PCB. 4, Before you install the steering assembly back in the simulator, turn the centering disk so the single hole in the disk is between the optical readers on the PCB. This will make it much easier to correctly install the steering wheel.
  • Put the steering assembly back in the cabinet. Install the four carriage bolts through the holes in the shelf. Tightly install the fender washers and nuts on the bolts so the assembly does not move.
  • Install the steering wheel with the center spoke down. Make sure the single hole on the centering disk is between the optical reader on the centering PCB so the steering wheel will be correctly centered, Put the center cover on the steering wheel. Install the three tamperproof screws and lock washers that hold the steering wheel on the steering assembly. Tighten the screws to 50 + 8 inch-pounds.

3-23

Page 58

Maintenance and Troubleshooting

  • Connect the steering assembly harness to the simulator harness. Attach the screw down tie wrap on the motor-opto harness to the cabinet. Make sure the wires will not be caught in the motor puliey. Connect the motor power harness to the motor amplifier PCB.
  • Install the back service door,
Note You must enter the seif-test and go through ihe Set Controls screens because you repaired the steering PCB. Otherwise the simulator will not work correctly.

Replacing the Centering

Disk

‘The centering disk gives information to the centering PCB about the position of the steering wheel. You should never have to replace the centering disk unless it has been bent or damaged through rough or careless handling. If the disk is bent and cannot be centered between the optical readers replace it immediately. If the disk is not bent, make sure the problem is the centering disk by following the troubleshooting table, Table 3-11 or a flowchart in Figure 3-10, 3-12, or 3-13.

Removing the Centering Disk

Turn off the power to the simulator.

  • Remove the three tamperproof screws and washers in the cover plate of the steering wheel. Take off the steering wheel and cover plate. See Figures 3-8 and 3-9.
  • Take off the back service door. Disconnect the steering assembly harness from the simulator harness. Disconnect the motor power from the motor amplifier PCB assembly. Remove the screw down tie wrap from the side of the cabinet. 4, Remove the four nuts that hold the steering assembly on the shelf. Push the screws through holes in the shelf. Remove the steering assembly.
  • Remove the belt on the front by pushing the motor towards the steering wheel mounting shaft and by working the belt off the pulleys.
  • Remove the pulley on the steering wheel shaft by loosening the socket-head screw that holds it on. (The socket-head screw has a penetrating adhesive on it.)

3-24 Hard Drivin’ Compact

  • Take off the PCB bracket on the side of the frame by removing the two screws that hold it on the frame.
  • Remove the socket-head screw from the disk collar. Push the disk collar, the centering disk and the disk stiffening ring towards the front of the frame (away from the pulley and belt end) about an inch.
  • Loosen the two socket-head screws on the bal! bearing.
  • Remove the one-inch retaining ring between the ball bearing and the centering disk. Push the shaft forward to reach the other retaining ring.
  • Remove the other one-inch retaining ring.
  • Push the shaft forward and pull the disk collar, centering disk, and disk stiffening ring off. 13, Remove the three socket-head screws and washers and take apart the disk collar, the centering disk and the disk stiffening ring.

— the Centering Disk

Assemble the new centering disk with the disk collar. The slot in the disk should be 90° clockwise from the hole for the socket-head screw on the disk collar.

  • Assembie the disk collar, centering disk, and disk stiffening ring with the three socket-head screws and washers. Tighten the socket-head screws to 15 + 3 inch-pounds,
  • Put the centering disk, collar, and stiffener on the steering wheel shaft. Make sure the socket-head screw hole is towards the front.
  • Install the one-inch retaining ring on the end of the shaft first. Then install the retaining ring between the ball bearing and the centering disk.

5. Tighten the two socket- head screws on the ball

bearing.

  • Make sure the disk collar is mounted on the shaft so the socket-head screw hole is over the flat on the shaft. Install the centering PCB bracket on the side of the frame. Make sure the centering disk is between the optical readers and does not touch them. Tighten the screws on the bracket to 10 + 3 inch-pounds,
  • Tighten the screw in the disk collar to 30 + 5 inchpounds on the flat of the shaft to hold the disk in place.
  • Put oil in the fill hole on the bronze bearing on the steering wheel mounting shaft if this has not been done recently,
  • Take the socket-head screw out of the pulley and put a penetrating adhesive on it. ~t
Page 59

Hard Drivin’ Compact

11.

12.

13. Steering wheel has no feedback during game play although you can play the game) and you have already tied the SEF CONTROLS screen,

Onthe CONTRO: INPUTS screen, does the wheel positon ro. increase smoothly as you um the whee! clack wise? Does the postion no. pecome zero ence every Measure the voltage on he “ro steering whee! positon inpus ‘onthe main PCB. Does the ingut change continuously fom 00 { and back when you tun he steering whee’? Maintenance and Troubleshooting

Check steering whee! harness. Check steering wheel encoder and centering disks and PCBs.

Go to the MAIN BOARD CONTROLS screen ‘Troubleshoot the optical poston circuit Troubleshoot the Motor Amp PCB. and choose the STEERING WHEEL item CChoose the SEND FORCE Test from the ee submenu sehemal

Doyou get he proper force on the steering wheel? between 6 and 12 2. ‘Cheok the resistance to the motor when itis cold, The resistance should be Isthe resistance too high or too tow?

Troubleshoot the optical position circuit ‘on the main PCB. See the main PCB schematio. Replace motor.

Figure 3-13 The Steering Wheel Has No Feedback and You Have Tried the Set Controls Screens

Slide the pulley on the back of the steering wheel shaft. Align this pulley to the other one. Install the socket-head screw so it is on the flat of the shaft. Tighten the screw to 50 + 8 inch-pounds. Install the belt by pushing the motor towards the steering wheel mounting shaft and working the belt onto the pulleys. Before you install the steering assembly back in the simulator, turn the centering disk so the single hole in the disk is between the optical readers on the PCB. This will make it much easier to correctly install the steering wheel. Put the steering assembly back in the cabinet. Install the four carriage bolts through the holes in the shelf. Tightly install the fender washers and nuts on the bolts so the assembly does not move.

  • Install the steering wheel with the center spok down. Make sure the single hole on the centerir disk is between the optical reader on the centerir, PCB so the steering wheel will be correctly cet tered, Put the center cover on the steering wheel. Insta the three tamperproof screws and lock washer that hold the steering wheel on the steering assen bly. Tighten the screws to 50 + 8 inch-pounds.
  • Connect the steering assembly harness to the simv lator harness. Attach the screw down tie wrap on the motor-opt harness to the cabinet. Make sure the wires will nc be caught in the motor pulley. Connect the mote power harness to the motor amplifier PCB.
  • Install the back service door.
Page 60

Maintenance and Troubleshooting

Note You musi enter the self-test and go through the Set Controis screens because you repaired the steering assembly. Otherwise the simulator will not work correctly.

Replacing the Encoder Disk

The encoder disk gives speed and direction information about the steering wheel movement to the encoder PCB. You should never have to replace the encoder disk unless it has been bent or damaged through rough or careless handling of the steering assembly. If the disk is bent and cannot be centered between the optical readers, replace it immediately. If the disk is not bent, make sure the problem is the encoder disk by following the troubleshooting table, Table 3-11 or the flowchart in Figure 3-10, 3-12, or 3- 13. To replace the encoder disk, do the following:

Removing the Encoder Disk

  • Turn off the power to the simulator.
  • Remove the three tamperproof screws and washers in the cover plate of the steering wheel. Take off the steering wheel and cover plate. See Figures 3-8 and 3-9.
  • Take off the back service door. Disconnect the steering assembly harness from the simulator harness. Disconnect the motor power from the motor amplifier PCB assembly. Remove the screw down tie wrap from the side of the cabinet.
  • Remove the four nuts that hold the steering assembly on the shelf. Push the screws through holes in the shelf. Remove the steering assembly.
  • Remove the harness from the encoder PCB over the encoder disk. Take off the two screws that hold the encoder PCB on the assembly. Remove the PCB.
  • Loosen the socket-head screw from the encoder disk collar. Take off the disk collar, the encoder disk and the disk stiffening ring, which are held together with three socket-head screws. Remove the three socket-head screws and washers and take apart the disk collar, the encoder disk and the disk stiffening ring. Hard Drivin’ Corapact

ingraline the Encoder Disk

. Replace the encoder disk. Assemble the disk collar, encoder disk, and disk stiffening ring with the three socket-head screws and washers. Tighten the screws to 15 + 3 inch-pounds.

  • Put the encoder disk, collar, and stiffener on the motor shaft, Make sure the hole for the sockethead screw faces out and is over the flat of the shaft.
  • Put on the encoder PCB so the optical readers and the harness connection face down. Move the encoder disk so it is between the two readers, but does not touch them. Tighten the screws on the encoder PCB to 10 + 3 inch-pounds. 4, Tighten the screw in the disk collar to 30 + 5 inchpounds to hold the disk in place. Make sure the

encoder disk stili does not touch the optical readers.

  • Install the harness on the encoder PCB.
  • Put oil in the fill hole on the bearing on the steering wheel mounting shaft if this has not been done recently.
  • Before you install the steering assembly back in the simulator, turn the centering disk so the single hole in the disk is between the optical readers on the PCB. This will make it much easier to correctly install the steering wheel.
  • Put the steering assembly back in the cabinet. Install the four carriage bolts through the holes in the shelf. Tightly install the fender washers and auts on the bolts so the assembly does not move.
  • Install the steering wheel with the center spoke down. Make sure the single hole on the centering disk is between the optical reader on the centering PCB so the steering wheel will be correctly centered. Put the center cover on the steering wheel. install the three tamperproof screws and lock washers
Page 61

Hard Drivin’ Compact

that hold the steering wheel on the steering assembly. Tighten the screws to 50 + 8 inch-pounds.

  • Connect the steering assembly harness to the simulator harness. Attach the screw down tie wrap on the motor-opto harness to the cabinet. Make sure the wires will not be caught in the motor pulley. Connect the motor power harness to the motor amplifier PCB.
  • Install the back service door.
Note You must enter the self-test and go through the Set Controls screens because you repaired the steering assembly. Otherwise the simulator will not work correctly.

Video Display

If you have problems with the video display, check Table 3-11, Troubleshooting the Video Display, before you remove the display.

Adjusting the Video Display

To make adjustments to the video display, open the top service door on the top of the cabinet.

Removing the Video Display

Perform the following procedure to remove the video display. (See Figure 3-14.)

  • Turn the simulator power off and wait two minutes. Leave the power cord plugged in.
  • While you wait, unlock the top service door on the top of the cabinet.
  • Remove the six washers and tamperproof screws in the bottom attraction retainer, and take off the bottom attraction retainer. Remove the three washers and hex-head screws in the top attraction retainer and also take this retainer off. Remove the attraction decal and shield. Maintenance and Troubleshooting
WARNING High Voltage The video display contains lethal high voltages. To avoid injury, do not service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation The video display is designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube may implode 'f struck or dropped. The shattered glass from the tube may cause injury up to six feet away. Use care when handling the display.

. Take off the board with the fluorescent light mounied on it. Disconnect the light harness from the simulator harness. . Open the back service door. Loosen the nuts on the carriage bolts in the front of the dashboard. You may have to loosen nuts on the other bolis that hold the dashboard in place or may even have to remove the dashboard to remove the video display shield and bezel, . After you remove the video display shield and bezel, take out the screws that hold the right and left video display shield wood brackets in place. Remove the wood brackets. . Remove the screws that hold the bottom attraction retainer in the cabinet, and take out the retainer. . Discharge the high voltage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: a. Attach one end of a solid 18-gauge wire to a well-insulated screwdriver or wooden handle. b.Attach the other end of the wire to an earth ground,

Table 3-13 Troubleshooting the Video Display

3-27

Page 62

Maintenance and Troubleshooting Hard Drivin’ Compact

046685-01 Cntr Retainer Decal 046615-01 Retainer Spacer 175014-3040 Flat Bik Wshr 176025-4116#10 Tamper Proof Bik Screw 178263-0402 1/4” Foam Tape 178181-6816 #8 Spacer 048600-01 037469-01 046579-01 TopAccess 139022-102 Video Display Lemp Bracket Olsplay Cleat Docr 177010-244 1/4 Locknut 046626-01 0-308 725516 1/4 Hex-Hd Screw ai Fuorescent Light 75-2458 1/4 Split-Lock Wshr 171086-001 175014-3040 Flat Blk Wshr Lamp Fixture 046622-01 Attract Retainer 178232-001 178263-04021/4" Foam Tape Retaining Clip 82-81198#10 x 1" Skt-Hd Bik Screw 4 175014-3050 1/4 Flat Bk Wshr

3 Z 046624-01 H 3 Video Display & 046681-01 Attrect Retainer Attract Dacal ‘7 046623-01 S Video Display & ‘A046568-01 : Attract Brokt Light Board Assy 046617-01 Lt Attract Cleat

046628-01 Video Display Bezel

046625-01 Front Bezel

046619-02 Rt Monitor Brkt 175004-708 .640 O.D. Fibr Wshr 175014-1050 Flat Wshr 177010-244 1/4 Locknut 046627-01 Video Shid /

046629-01 Mirror 178263-0402 1/4" Foam Tape

Figure 3-14 Removing the Video Control

¢. Quickly touch the blade end of the screwdriver to the CRT anode by sliding it under the anode WARNING cap: When you take the video display out of d. Wait two minutes and repeat part c. the cabinet, do not drop it! The display is

  • Disconnect the harness connectors from the video heavy. Be carefull display. Wear gloves to protect your hands from
  • Remove the screws that hold the video display as- the sheet-metal edges.

sembly on the video display mounting brackeis. The front screws have a flat washer, lock washer Replacing the Video and a nut on them. The rear screws have only a washer and no nut. Display

  • Pull the video display assembly out of the cabinet. Perform the following procedure t 1 ne vidi Be extremely careful, erform following procedure to replace the video display in the cabinet. (See Figure 3-14.)

3-28

Page 63

Hard Drivin’ Compact

Note If you replace the entire video display or the yoke, reverse the wires on the vertical winding before installing the display in the cabinet.
  • Carefully lift the video display into the cabinet.
  • Install the screws that hold the video display assembly on the video display mounting brackets. Put a flat washer, lock washer and a nut on the front screws. The rear screws have only a washer.
  • Connect the power and signal harnesses to the video display. 4, Install the bottom attraction retainer with the tamperproof screws. Replace the right and left video display shield brackets.
  • Install the video display shield and bezel. Replace the dashboard if you removed it. Tighten all the Maintenance and Troubleshooting

nuts on the carriage bolts that hold the dashboard in place.

  • Connect the light harness to the simulator harness. Install the board with the fluorescent light mounted on it.
  • Install the attraction decal and shield. Install the top attraction retainer with the three hex-head screws.
Note When you replace the cathode-ray tube and yoke together, adjust the brightness, size, and centering as described in the video display service manual. Check the purity and convergence according to the service manual instructions, but adjust both only if required.
  • Lock the top service door on the top of the cabinet.

3-29

Page 64

Maintenance and Troubleshooting Hard Drivin’ Compact

N O T E S

3-30

Page 65

ILLUSTRATED PARTS LISTS

Chapter 4

This chapter provides informa: tion you need to order parts for p your game. Common hardware parts, such as screws, nuts, washers, and so on usually are not listed in the parts lists. The parts lists (except for the PCB parts lists) are arranged alphanumerically by Atari part number. All A-prefix numbers, which are assemblies, come first. Next are part numbers with six numbers followed by a hyphen (XXXXXX-XX). Ending the list are part numbers with a two-number designation followed by a hyphen (XX-). The PCB parts lists are arranged in alphabetical order by component. Within each section the parts are arranged numerically by J part number. When you order parts, give the part number, part name, the number of this manual, and the serial number of your game. With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games. Atari Games Customer Service phone numbers are listed on the inside front cover of this manuai.

Page 66

Mlustrated Parts Lists Hard Drivin’ Compact

(046685-01 Catr Retainer Decal 046615-01 Retainer Spacer 175014-2040 Flat Bik Wshr 176025-4116#10 Tamper Proof Blk Screw 178263-0402 1/4" Foam Tape 178181-6816 #8 Spacer 046600-01

\037469-01046579-01Top Access139022-102 Video Display
Lamp BracketDisplay CleatDoor177010-244 1/4 Locknut
046626-0170-%72-8516 1/4 Hex-Hd Screw
FluorescentLight75-045S 1/4 Split-Lock Wshr
Airact SNri086.00"175014-3040 Flat Blk Wshr

Lamp Fixture 046622-01 Attract Retainer 178232-001 178263-04021/4" Foam Tape 82-8116B#10 x 1" Skt-Hd Bik Screw 175014-3050 1/4 Flat Blk Wshr Retaining Clip

yy 04662401 a Video Display & tran Dood! g Attract Retainer ‘ NL 046623-01 ia Video Display & 04656801 7. Attract Brokt Light Board Assy 048617-01 Lt Attract Cleat

046625-01 From Bezel

046627-01 e ee 708 Video Shid : = |e 840 0.D. Fibr Wshr

{:‘:é:175014-1050

Flat Wshr 177010-244 1/4 Locknut

046629-01 Mirror -178263-0402 4/4" Foam Tape

178099-005 ‘Sirg Wheel

trg Whl Decal 04g655-01 “Soccer Stig Whi Cover Plate 4 175014-3050, Flat Washer 1776025-4416' Tamper Proof Seew| / 8046567-01 / 78-3201 Contral Panel Assy \ Adjustable

175014-105072-5528oSGlide

Flat Wshr 4/4 Hex-Hd 177010-244 : 04662002

+4 Locknut046693-01pagRt Floor Trim
177012411Seat Back:
Spring NutDe7
17024-0144sabatonA046916-01

114 Low-Crown Bik Nut Gas & Brake Pedal Assy 75-5520B 82-8516B

1/4 x1 1/4" Blk Carriage BoltAossois-o170020-220114-20 x 1" Bitn-Hd Blk Screw
«BkCaterClutch Pedai Assy #8 X-Rec Bik Screw76025-4116
1/4x 1 3/4" Bik Carriage Bot1750148080t76025-4116#10 Tamper Proof Blk Screw

75-07002 17014-3050

a Fer yoe41/4 Fat Blk Wshr#10 Tamper Proof Bik Screw$75014-3060

178263-042 176012220 Foam Tape | Sorew Figure 4-1 Cabinet-Mounted Assemblies, Front View A046565-01 D 4-2

Page 67

Hard Drivin’ Compact Illustrated Parts Lists

‘A046575-01 Cabinet Assy

142028-001 NOTE: Steering Assembly Ballast Js rotated for clarity. Transformer

046680-01 Side Panel Decal

046642-01 Steering Assy

oN 75-07002 ~N 1/4 Fender Wshr lee 177010-244 Lock Nut 171027-001 Coin Door @ A046640-01 Htems Not meee eed

Shown:cSPCB Stand-Off

‘A005493-01 Fluorescent Light Hamess A046326-01 > ] PCB Interconnect . area Hamess Assy oO K Soniece ADIG336-01 176015-112 Motor Ribbon Cable Assy| yrnyeat? ; A046337- ‘Sera Not Shown, ent’d:

PCB Ribbon Cable Assy°160034-241
A039254-017e-6h00275-5520BVolume Switch

Component Harness Assy 4/4 Carriage Bolt 150048001

'A046660-01Floor MatAuxiliary Coin Credit Switch
Main Hamess Assy‘A046901-01‘A046673-0104657001
Peonss6: ae assyven PCBPower SupplyVideo Sara Pad

ower Harness ry

‘A046662-01maeeateA043910-01|Video Display Dampener Brekt
AC Harness AssyAnasaet-01SoyHOHextd — On/Off Switch046618-01
‘A046663-01Sound PCB Assy‘Sorew‘AssyMirror Retainer
Video Hames Assy‘A045989-0175-0408046619-01
‘A046664-01ADSP PCB Assy#10 Split-LockLt Monitor Brekt
Strg Optical PCBs175004-706Wshr046684-01
Interconnect Harness.375 O.D. Fibr WshrLt Seat Decal

175004-708 79-561816P

178126-002.640 0.D. Fibr WshrWire Nut
Tamper-Proof Hex Key176033-161099-11009

Driver #6 X-Rec Screw Light Starter Sckt A046340-01 99-11003 Component Bracket Assy’ Light Starter (inside seat). Parts: 046617-02 A046341-01 At Attract Cleat Coin Counter Assy 046620-01 119006-103 Lt Floor Trim Figure 4-1 Cabinet-Mounted Assemblies, Rear View A046565-01 D

Page 68

Illustrated Parts Lists Hard Drivin’ Compact

Cabinet-Mounted Assemblies Parts List

Part No. Description Part No. Description

A005493-01Fluorescent Light Harness046619-02Right Monitor Bracket
A043910-01On/Off Switch Assembly with Harness046620-01Left Floor Trim
A045989-01ADSP PCB Assembly046620-02Right Floor Trim
A046326-01PCB Interconnect Harness Assembly046622-01Attraction Retainer
A046336-01Motor Ribbon Cable Assembly046623-01Video Display and Attraction Bracket
‘A046337-01PCB Ribbon Cable Assembly046624-01Video Display and Attraction Retainer

046625-01 Front Bezel

A046340-01Component Bracket Assembly. Replaceable046626-01Attraction Shield

Parts:

A039254-01 | Component Harness Assembly046627-01Video Shield
A046341-01Coin Counter Assembly046628-01Video Display Bezel
119006-10310 KQ Audio Potentiometer046629-01Mirror

046655-01 Steering Wheel Cover Plate 160034-241 Slide Switch

160049-001Black Lens Switch046680-01Side Panel Decal

046681-01 Attraction Decal

A046491-01Sound PCB Assembly046683-01Seat Back Decal
A046567-01Control Panel Assembly (See Figure 4-2)046684-01_Left Side Seat Decal

A046568-01 Light Board Assembly

A046575-01Cabinet Assembly046685-01Center Decal

139022-102 25-Inch Standard Resolution Video Display

A046640-01Motor Amplifier PCB Assembly (See Figure142028-00160 Hz Ballast Transformer
4-12)148007-0034 1/2-Inch-Diameter 10-Watt Speaker

A046642-01 Steering Assembly (See Figure 4-4)

A046660-01Main Harness Assembly171027-001 — Sectioned Coin Door with Harness (See Figure
A046661-01Power Harness Assembly4-8)

171086-001 — 18-Inch Fluorescent Lamp Fixture

A046662-01AC Harness Assembly175004-706375 O.D. x .125-Inch-Thick Fiber Washer
A046663-01Video Harness Assembly175004-708.640 O.D. x .125-Inch-Thick Fiber Washer

A046664-01- Steering Optical Encoder Interconnect Harness

Assembly175014-10501/4 Flat Washer
A046673-01Power Supply Assembly (See Figure 4-9)175014-3040#10 Flat Black Washer

175014-3050 1/4 Flat Black Washer

A046901-01Hard Drivin’ Compact Main (Multisync) PCB176012-220#8 x1 1/4-Inch Flat Countersink Black Wood

Assembly (See Figure 4-10) Screw A046915-01 Clutch Pedal Assembly (See Figure 4-7)

A046916-01Gas and Brake Pedal Assembly (See Figure176015-112#10 x 3/4-Inch Cross-Recessed Screw
46)176020-220#8 x 1 1/4-Inch Cross-Recessed Black Screw
037469-01Lamp Bracket176025-4116#10-32 x 4-Inch Tamper Proof Black Screw

176025-4416 1/4-20 x 1-Inch Tamper Proof Screw 038091-01 Cash Box

046459-01Steering Wheel Cover Decal176033-1610#6 x 5/8-Inch Cross-Recessed Screw
046570-01Monitor Dampener Pad.177010-244 — 1/4-20 Polymer Locknut
046571-01Monitor Dampener Bracket177012-111Push-On Spring Nut

17024-0144 1/4-20 Low-Crown Black Nut 046579-01 Display Cleat

046598-01Back Service Door178093-001Fan Blade Guard
046600-01Top Access Door178099-005—_12-Inch Steering Wheel
046615-01Retainer Spacer178120606.375-Inch PCB Stand-Off

178126-002 5/32 Tamper-Proof Hex Key Driver 046617-01 Left Attraction Cleat

046617-02Right Attraction Cleat178181-6816 #8 x 1-Inch-Long Aluminum Spacer
046618-01Mirror Retainer178232-001 —_ Fluorescent Lamp Retaining Clip
046619-01Left Monitor Bracket178263-04021/4-Inch-Wide Foam Tape

70-304 15-Watt, 18-Inch Fluorescent Light

4-4

Page 69

Hard Drivin’ Compact Illustrated Parts Lists

Cabinet-Mounted. Assemblies, Continued Parts List

Part No. Description Part No. Description

72-511610-24 x 1Inch Hex-Head Screw82-8516B_1/4-20 x 1-Inch-Long Button-Head Black
72-55161/4-20 x 1-Inch Hex-Head ScrewScrew
75-0408#10 Split-Lock Washer99-11009Fluorescent Light Starter Socket
75-04581/4 Split-Lock Washer99-11003Fluorescent Light Starter

75-5520B 1/4-20 x 1 1/4-Inch-Long Black Carriage Bolt 75-5528B 1/4-20 x 1 3/4-Inch-Long Black Carriage Bolt These are the technical documents for the Hard Drivin’ 75-07002 ‘1/4 Fender Washer Compact simulator: , | $P-329 Compact Hard Drivin’ Schematic Package

78-3201Adjustable Glide$T-329Compact Hard Drivin’ Self-Test Label
78-6H002_—Floor MatT™M-329Compact Hard Drivin’ Operator's Manual
79-561816PWire Nut™M-330Wells-Gardner 25-Inch Standard-Resolution
82-8116B10-24 x 1-Inch-Long Socket-Head Black ScrewVideo Display Manual
Page 70

Ilustrated Parts Lists Hard Drivin’ Compact

Items Not Shown: A046666-01 Start Harness Assy A046667-01 Shifter Harness Assy 046668-01 Abort Harness Assy

175014-3050 Flat Blk Wshr 177024-0144 Low Crown Nut

160052-001 Pushbutton ‘Switch 036895-01 ‘Switch Bezel 046621-01 Control Panel Pecan (046682-01 aid Control Panel Decal ‘75-5520B 1/4 Black Carriage Bolt 177012-111

Fender Wshr 177010-244 046655-01 : acon Lock Nut Strg Whl Center ‘ \ Cover ‘A047000-01 Y . Key Switch Assy 046459-01 4 . y 75-5112B Strg Whl Decal . 4 j 1/4 Carriage Bolt : 177010-244 Lock Nut

A043936-06 Shifter Assy 75-0555 75-5124B Lock Washer #10 Carriage Bolt 176025-4416 175014-1043 Tamperproot Screw Flat Washer 178099-005, Bed Steering Wheel

Figure 4-2 Dashboard Assembly A046567-01 D

4-6

Page 71

Hard Drivin’ Compact Illustrated Parts Lists

Dashboard Assembly Parts List

Part No. Description Part No. Description

A043936-06H-Pattern Shifter Assembly (See Figure 4-4)176025-44161/4-20 x 1-Inch-Long Black Button-Head
A046666-01Engine Start Harness AssemblyTamperproof Screw
A046667-01Shifter Harness Assembly177010-240#10-24 Polymer Locknut
A046668-01Abort Button Harness Assembly177010-244—1/4-20 Polymer Locknut
A047000-01Key Switch Assembly (See Figure 4-5)177012-1111/4 Spring Nut
036895-01Switch Bezel17724-01441/4-20 Black Low Crown Nut
046459-01Steering Wheel Decal178099-00512-Inch Steering Wheel
046621-01Control Panel75-055B1/4 Black Lock Washer
046655-01Steering Wheel Center Cover75-070021/4 Fender Washer
046682-01Control Panel Decal75-5112B— #10-24 x 5/8-Inch-Long Black Carriage Bolt
160052-001Red Lighted Pushbutton Switch75-5124B-#10-24 x 1 1/2-Inch-Long Black Carriage Bolt
175014-1043.234 LD., .625 O. D. Flat Washer75-5528B—-1/4-20 x 1 3/4-Inch-Long Black Carriage Bolt

175014-3050 1/4 Flat Black Washer

EN “I

Page 72

Illustrated Parts Lists Hard Drivin’ Compact

72-5432 3/8-16 x 2” 177010-248 Hex Bolt 175014-1070 18 Lock Nut \ 7716 Fit Wshr

1/4" Spacer 175014-1063 GA6652-01 47010-24898 Fit Wehr 041787-02 5/8" Spacer 38 Lock Nut 106007-001 Encoder Disk Adhesive 178012-010 1" Clip Ring

178268-001 Ball Bearing

046650-02

046646-01 Pivot Plate

046647-01 72-8808 : : PCB Mintg Brit #8 Skt-Hd Screw : 75-0488 #8 Split-Lock a7s014'1032 72-CT604 #8 Fit Wshr #692 Hex Whe crew

ms "I A046691-01 Centering Disk | Centering Disk Hex Bolt Collar antoring Items Not Shown: y

avers 043807-02 #4-40 Sckt-Hd Screw cantering Disk 75-0448 #4 Split-Lck Wshr 046644-01 Strg Whl Mntg Steering Wheel and Shaft Mounting Hardware

176022-3806 #8-32 Skt-Hd Screw 046459-( Strg WhI Decal 046655-01 Strg WhI Center Cover 176025-4416 1/4-20 Blk Tamperproof Screw 178099-005 Steering Wheel 75-0553 1/4 Bik Lek Wshr

Figure 4-3 Steering Assembly, Front View A046642-01 D

Page 73

Illustrated Parts Lists. Hard Drivin’ Compact

Motor Assy A046689-01

A046674-01 Encoder Disk PCB Assy 72-CT604 #6-32 Hex Wshr Hd Screw 107013-001 Oil 178269-001 Bronze Bearing 4 107013-001 Oil

046648-01 Disk Stiffening

-1046 Pulley V-Belt 178271 ‘A046665-01 Motor-Opto Harness Assy

72-5416 9/8-16 x 1" Hex Bolt 106007-001 Penetrating Adhesive

1/2 Fit Wshr 178012-006, 175014-1077

Clip Ring 12" 046645-01 Pivot Shaft 178026-022 Spring

046643-01

Figure 4-3 Steering Assembly, Rear View A046642-01 D

Page 74

Illustrated Parts Lists Hard Drivin’ Compact

Steering Assembly Parts List

Part No. Description Part No. Description

A046665-01Motor-Opto Harness Assembly175014-1032#8 Steel/Zinc Flat Washer
A046674-01Motor Assembly175014-10633/8 Steel/Zinc Flat Washer
A046689-01Encoder Disk PCB Assembly (See Figure 4-13)175014-10707/16 Steel/Zinc Flat Washer
A046691-01Centering Disk PCB Assembly (See Figure175014-10771/2-Inch Flat Washer

4-14) 176022-3806 #8-32 x 3/8, Thread-Lock Socket-Head Screw

041787-02Encoder Disk176025-44161/4-20 x 1,00-Inch-Long Black Tamper Proof
043807-02Centering DiskScrew
046459-01Steering Wheel Cover Decal177010-2483/8-16 Lock Nut
046643-01Frame178012-0061/2-Inch-Diameter Clip Ring
046644-01Steering Wheel Mounting Shaft178012-010—_1-Inch-Diameter Clip Ring
046645-01Pivot Shaft178026-0221.0-Inch x 4.0-Inch Extension Spring
046646-01Pivot Plate178099-00512-Inch Steering Wheel
046647-01PCB Mounting Bracket178268-001Pillow Block Ball Bearing
046648-01Disk Stiffening Ring178269-001Pillow Block Bronze Bearing
046650-01Centering Disk Collar178270-0032-Inch Pulley
046650-02Encoder Disk Collar178270-0026-Inch Pulley
046652-013/4 O.D. x 3/8 LD. x 5/8-Inch-Long Spacer178271-1046Pulley V-Belt

(Alternate parts: part no. 178272-6910, alumi-

num spacer, or past no. 178272-7910,72-54163/8-16 x 1-Inch Hex Bolt
steel/zinc spacer.)72-54323/8-16 x 2-Inch Hex Bolt

72-8406 #4-40 x 3/8-Inch Socket-Head Screw

046652-033/4 O.D. x 3/8 LD. x 1/4-Inch-Long Spacer72-8808#8-32 x .50-Inch Socket-Head Screw

(Alternate parts: part no. 178272-6910, alumi-

num spacer, or part no. 178272-7910,72-C¥604-#6-32 x .25-Inch-Long Hex Washer Head

steel/zinc spacer.) Screw

046655-01Steering Wheel Center Cover Plate75-0445,#4 Split-Lock Washer
106007-001Penetrating Adhesive75-0488#8 Split-Lock Washer
107013-001Light Oil75-055B1/4 Black Lock Washer

4-10

Page 75

Hard Drivin’ Compact Illustrated Parts Lists

75-5124B #10-24 Bik Carriage Bolt 178027-001 Lithium Lubricant 005255-02 a Shifter Bezel ea

039154-01

‘A000610-02 Handle Assy

039705-01 Compression Spring

178219-001 3/8" Ball

477010-240 #10-24 Locknut Housing 175014-1043 Flat Washer

000611-02 oN HePattern Detent 043711-01 Return Spring anata aw 177010-232 72-JB3606 =~ 4-40 Hex Nut 160053-001 sere rex ons Wshr-Hd Screw 7214128 043712-01 #4-40 X-Rec Screw ‘Switch Spacer

Figure 4-4 Shifter Assembly A043936-06 A

Page 76

Illustrated Parts Lists Hard Drivin’ Compact

Shifter Assembly Parts List

Part No. Description Part No. Description

A000610-02Handle Assembly160053-001Mini-Low Force Switch
000609-02Housing175014-10430.234 LD. x 0.625 O.D. Flat Washer
000611-02—-H-Pattern Detent177010-232#4-40 Self-Locking Polymer Hex Nut
005255-02Shifter Bezel177010-240#10-24 Polymer Locknut
039154-01Shifter Spacer178027-001_Lithium-Base Lubricant
039705-01Compression Spring178219-0013/8-inch Diameter Ball
043700-01Actuator Pin72-14128#4-40 X 3/4-Inch Cross-Recessed Screw
043711-01Return Plunger Spring72-J83606#6-19 X 0.38-Inch Hex Washer-Head Screw
043712-01Micro-Switch Spacer75-5124B#10-24 x 1 1/2-Inch Long Black Carriage Bolt

4-12

Page 77

Hard Drivin’ Compact illustrated Parts Lists

176008-110 | tsps weerot #10 Sokt-Hd Screw a= ange | ys.ouos #10 Spit- —— 175009-364 hems Not Shown: ‘Nylon Washer 172020-0814 Spring Pin

178001 -004 bi coer 1/2" Retaining Ring 42" Retaining Ring

160045-003 Switch

NOTE: The switch is installed in the game rotated 180° from the position it is 046999-01 shown in here. | Housing

177010-232 #4 Hex Locknut T2-A412S #4-49 Screw 75-0148 #4 Flat Wshr

Figure 4-5 Key Switch Assembly A047000-01 A

Key Switch Assembly Parts List

Part No.DescriptionPart No.Description
046448-01Key176008-116#10-32 x 5/8-Inch-Long Socket-Head Screw
046449-01Shaft177010-232 — #4-40 Polymer Hex Lock Nut
046450-01Actuator178001-004—_1/2-Inch Retaining Ring
046999-01_Housing178256-001Torsion Spring
107029-001Lithium Grease72-14128#4-40 x 3/4-Inch-Long Cross-Recessed Screw *
160045-003SPDT Switch75-0148#4 Flat Washer
172020-0814Straight Slotted Spring Pin75-0408#10 Split-Lock Washer

175009-364 Nylon Washer

4-13

Page 78

Illustrated Parts Lists Hard Drivin’ Compact

047211-01 ] Lower Link 177000-138 #8 Hex Nut 72-8810 #8-32 Sckt-Hd Screw 4 107027-001 Lithium Grease

72-8810 #8 SK-Hd Screw

98-215009 Left-Wound Spring

047217-01 Bumper Sleeve snomesoo: 047218-01 Rubber Bumper Tee 12.0125 Potentiometer

A047085-01 Brake Pedat Replacement Kit Assy

82-8516B Button Hd Screw 175014-3050 Flat Bik Wshr

176012-220 176025-4416 Wood Sorew — —— ‘Femiperproal NOTE: All parts not called out are 175014-3050 pari of Front and Sides Assembly, Flat Bik Wshr part number 171092-001.

Items Not Shown: A046669-01 Gas Harness Assy

Figure 4-6 Brake and Gas Pedal Assembly A046916-01 B

Page 79

Hard Drivin’ Compact Thustrated Parts Lists

Brake and Gas Pedal Assembly Parts List

Part No. Description Part No. Description

A046669-01Gas Harness Assembly171092-001Front and Sides Assembly (Also includes
A047085-01Brake Pedal Replacement Kit Assembly (pedalbumpers, bumper sieeves, [except for the

with strain gauge and harness attached) bottom brake bumper and bumper shaft]

047210-01Upper Linkand securing hardware.)
047211-01Lower Link175012-01250.385 I.D., 0.625 O.D. Flat Washer

177000-138 = #8 Hex Nut

047217-01Bottom Brake Bumper Sieeve72-8810#8-32 x 5/8-Inch-Long Socket-Head Screw

047218-01 Bottom Brake Rubber Bumper

107027-001Lithium Grease99-215006Gas Pedal
119008-10015 KQ Potentiometer99-215008Right-Wound Spring

99-215009 _Left-Wound Spring

4-15

Page 80

Illustrated Parts Lists Hard Drivin’ Compact

107027-001 Lithium Grease de 047210-01 Upper Link 175012-0125 177000-138 Flat Washer 047211-01 #8 Hex Nut Lower Link 72-9810 177000-138 #8-82 Sckt- 19008-1001 Potentiometer

Clutch Side Hole Pattern

176025-4416 ‘Tamperproof Screw 175014-3050 Flat Bik Wshr

99-215006 Clutch Pedal

NOTE: All parts not called out are part of the Front and Sides Assembly, part number 171092-001. Right-Wound Spring 82-8516B Button Hd Screw 175014-3050 Fit Bik Wshr

Item Not Shown. A046671-01 Clutch Harness Assy a

Figure 4-7 Clutch Pedal Assembly A046915-01 B Clutch Pedal Assembly Parts List

Part No. Description Part No. Descriptica

A046671-01Clutch Hamess Assembly175012-0125385 L.D., .625 O.D. Flat Washer
047210-01Upper Link177000-138#8 Hex Nut
047211-01Lower Link72-8810#8-32 x 5/8-Inch-Long Socket-Head Screw
107027-001Lithium Grease99-215006Clutch Pedal
119008-10015 KQ Potentiometer99-215008Right-Wound Spring
171091-001Clutch Pedal Front and Sides Assembly (Also99-215009Left-Wound Spring

includes bumpers, bumper sleeves, and securing hardware.)

4-16

Page 81

Hard Drivin’ Compact Ilustrated Parts Lists

N O T E S

4-17

Page 82

Ilustrated Parts Lists Hasd Drivin’ Compact

99-10140 Panel Assembly

99-4016 Lever

99-10152 Right Coin Iniet 99-10147 Harness 171006-035 Coin Mechanism

75.9448 Locknut

99-10096 Fastener

99-10151 Left Coin Inet

7011-47 Lamp

99-10080 Lamp Socket

99-10105, Bar

99-10104

99-1042 thru 99-1045 a Coin Switch Assembly

99-10150 ‘Switch Cover 99-10154 Bracket Assembly B 99-10153 Ue Coin Return Box ra “ 99-10068 Coin Chute 65-441C : \ he Coin Switch . i ~ 9910075 thru 99-10078 RN Switch Wires "

99-10008 Retainer 75-1412S ‘Screw

Figure 4-8 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

4-18

Page 83

Hard Drivin’ Compact Illustrated Pans Lists

99-10148 Lock Assembly

T2-HA1404C Screw

99-10139 Coin Door

98-10148 Lock Assembly

72-JA1405B Screw

038091.01 Coin Box

NOTE

The acceptable substitute for this deor (and the one used in games manufactured in Ireland) is the Coin Controls Ltd. Coin Door Assembly, part number 171034-001. You can obtain a free Coin Controls Ltd. supplement (part. no. CO-305-01) that has illustrations and a parts list. Write to Atari Games ireland Limited, Tipperary Town, Ireland. Telephone 062-52155. 99-10160 Coin Inlet Housing

99-10161 |<——— Side Entry Button Assy

99-10115, Spring

99-1041 Coin Return Cover

99-1019) Coin Retum loor

i——— 99-1044 ChanneClip

so-t966 Sow

99-107144 Service Da,

99-10745 Frame

Figure 4-8 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001 A

Page 84

Illustrated Parts Lists Hard Drivin’ Compact

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part No. Description Part No. Description

160057-001Coin Switch99-10081Key Holder
70-11-47Miniature Bayonet Lamp99-10096Fastener
72-9406#4-40 x 3/8-Inch Truss-Head Screw99-10104Bar Retainer
72-HA1404C_#4-40 x 1/4-Inch Pan-Head Screw99-10105Bar
72-JA1405B — #4-40 x .31-Inch Pan-Head Screw99-10115Spring
75-1412S#4-40 x 3/4-Inch Pan-Head Screw99-10116Plastic Coin Return Lever
75-9945,#4-40 Locknut99-10117Steel Coin Return Door
99-10008Retainer99-10139Coin Door
99-10042Coin Switch Assembly for Belgian 5 Fr and99-10140Coin Door Inner-Panel Assembly
US. 25¢99-10141Die-Cast Coin Return Cover
99-10043Coin Switch Assembly for German 1 DM,99-10143Coin Door Frame
Japanese 100 Yen, Swiss 1 Fr99-10144Channel Clip

99-10044 Coin Switch Assembly for German 2 DM,

Italian 100 L, U.S. $1.0099-10147Harness
99-10045,Coin Switch Assembly for Australian $.20,99-10148Lock Assembly
German 5 DM, British 10 P99-10149Service Door

99-10150 Switch Cover 99-10068 Coin Return Chute

99-10075Switch Wire (included in coin switch assembly99-10151Left Coin Inlet
99-1043)99-10152Right Coin Inlet
99-10076Switch Wire (included in coin switch assembly99-10153Coin Return Box
99-10042)99-10154Bracket Assembly

99-10077 Switch Wire (included in coin switch assembly

99-10044)99-101601-Inch Wide Die-Cast Coin Inlet Housing
99-10078Switch Wire (included in coin switch assembly99-1016125¢ Amber Side-Entry Coin Button Assembly
99-10045)99-15066Screw for Clamp
99-10080Lamp Socket171006-035Metal Coin Mechanism for U.S. 25¢

4-20

Page 85

Hard Drivin’ Compact Illustrated Parts Lists

N O T E S

4-21

Page 86

Ilustrated Parts Lists Hard Drivin’ Compact

179231-002 AQ46346-02 A046346-01 149005-002 2-Position 15" Wht 15"Bik — A043367-01 ‘Switching Power Supply Terminal Block Jumper Assy Jumper Assy Jumper Assy

Line Filter Assy

179225-2205 5-Position Fuse

2 Amp, 250V 142051-001 Fuse Transformer

Figure 4-9 Power Supply Assembly A046673-01 A

4-22

Page 87

Hard Drivin’ Compact Illustrated Parts Lists

Power Supply Assembly Parts List

Part No.DescriptionPart No.Description
A042384-01Line Filter Assembly146008-20222 Amp, 250V Slow Blow Fuse
A043367-01Jumper Assembly146008-3022 3 Amp, 250V Slow Blow Fuse
A044431-02‘APU PCB Assembly (See Figure 4-11)149005-0025 Volt, 15 Amp Hitron Switching Power
A046346-01_15-Inch Black Jumper AssemblySupply (See Below)
A046346-02_15-Inch White Jumper Assembly179225-22055 Position Fuse Block
034544-01Fuse Black Cover179231-0022 Position Terminal Block.

142051-001 Transformer

Hitron 5 Volt, 15 Amp Power Supply Sub-Assembly Parts List

Part No.DescriptionPart No.Description
Transistors99-211026Resistor, Carbon Film, 330 Ohm, 5%, 1/4W
99-211002‘Transistor, NPN, 28C1413A99-211027Resistor, Carbon Film, 5.6 Ohm, 5%, 1/4W
i99-211028Resistor, Carbon Film, 8.2 Ohm, 5%, 1/4W
aontt0SEi eeaglg eel etc99-211029Resistor,Carbon Film,10 Ohm, 5%, 1/4W
99-211004Transistor, PNP, PE8550Bi‘sister,im,ham
eotioesTaoclee bebssoe99-211030Resistor, Carbon Film, 39 Ohm, 5%, 1/4W
,99-211031Resistor, Carbon Film, 56 Ohm, 5%, 1/4W
Diodes99-211032Resistor, Carbon Film, 1K Ohm, 5%, 1/4W

99-211033 Resistor, Metai Film, 2K Ohm, 2%, 1/4W 99-211005 Diode, Schottky, S10SC4M

99-211006Diode, Fast Recovery, 30DF199-211034Resistor, Carbon Film, 180K Ohm, 5%, 1W
99-211007Diode, Zener, 1N752A99-211035Resistor, Carbon Film, 2K Ohm, 5%, 1/4W
99-211008Diode, Rectifier, 1N400699-211065Resistor, Wire Wound, 27 Ohm, 5%, 2W

99-211066 Resistor, Carbon Film, 6.8 Ohm, 5%, 1/2W 99-211009 Diode, Fast Recovery, Rpg10B

99-211010Diode, Fast Recovery, Rpgl0K99-211067Resistor, Carbon Film, 12 Ohm, 5%, 1/4W
99-211011Diode, Fast Recovery, Rpgi5B99-211068Resistor.Carbon Film, 2.4 Ohm, 5%, 1/2W
99-211012Diode, Switching, 1N414899-211077Resistor, 470 Ohm, 1/2W, 5%

99-211078 Resistor, 120K Ohm, 1W, 5% 99-211064 Diode, $15SC4M

99-211076Diode, 31DQ04Capacitors
99-211013Rectifier, Silicon Controlled, $280099-211036Capacitor, Metal Film, 0.047UR, 250V
ist99-211037Capacitor, Metal Film, 0.22UF, 100V
ee|99-211038Capacitor, Metal Film, 0.1UF, 400V
99-211014Potentiometer, Trimming, 3K Ohm99-211039Capacitor, Metal Film, 0.022UF, 100V

99-211015 Resistor, Wire Wound, 50 Ohm, 5%, 2W

99-211016Resistor, Wire Wound, 150 Ohm, 5%, 2099-211040Capacitor, Ceramic, 1800PF, 2KV, Z5V
99-211017Resistor, Wire Wound, 33 Ohm, 5%, 2W99-211041Capacitor, Ceramic, 0.01UF, 1KV, Z5U

99-211042 Capacitor, Ceramic, 0.001UF, 2KV

99-211018Resistor, Wire Wound, 0.47 Ohm, 5%, 2W99-211043Capacitor, Ceramic, 470PF, 1KV, Z5P

99-211019 Resistor, Wire Wound, 120 Ohm, 5%, 2W

99-211020Thermistor, 0.5 Ohm, 5%, SW99-211044Capacitor, Electrolytic, 470UF, 25V
99-211021Resistor, 22K Ohm, 2%, 1/4W99-211045Capacitor, Electrolytic, 220UF, 25V

99-211046 Capacitor, Electrolytic, 100UF, 200V

99-211022Resistor, Carbon Film, 330 Ohm, 5%, 1/2W99-211047Capacitor, Electrolytic, 1000UF, 25V

99-211023 Resistor, Carbon Film, 270 Ohm, 5%, 1/2W

99-211024Resistor, Carbon Film, 470 Ohm, 5%, 1/4W99-211048Capacitor, Electrolytic, 2200UF, 16V
99-211025Resistor, Carbon Film, 47 Ohm, 5%, 1/4W99-211049Capacitor, Ceramic, 4700UF, 400V

4-23

Page 88

Ilustrated Parts Lists Hard Drivin’ Compact

Hitron 5 Volt, 15 Amp Power Supply Sub-Assembly Parts List

Part No. Description Part No. Description

99-211069Capacitor, Electrolytic, 2200UF, 16V99-211088Inductor, 60MH

99-211070 Capacitor, Electrolytic, 220UF, 25V

99-211079Capacitor, De7100F22MTransformers
99-211080Capacitor, 1000UF, 35V99-211075‘Transformer, Power

99-211083, Transformer, Power

99-211081Capacitor, 470UF, 25V99-211089Transformer, 4.75MH
99-211082Capacitor, 220UF, 16V99-211092Transformer
99-211090Capacitor, Ceramic, 1000PF, 2KV99-211055‘Transformer

99-211091 Capacitor, Electrolytic, 2200UF, 10V Inductors 99-211001 R snes Unisnaw egulator,

99-211050Inductor, 7UH99-211056Fuse, 2A, 250V.
99-211051Inductor, 7UH, 35MM99-211057Terminal Block, 8CKT
99-211052Inductor, 15MH2110582A, 250V, Semki
99-211053Inductor, 1.5MH—_BeSeeame

99-211059 Heatsink

99-211054Inductor, 2.2UH99-211060Fuse Holder, 6.35MM
99-211071Inductor, 9.8UH99-211061Heatsink, 1.5MM
99-211084Inductor, 8UH211072FuseHolder, 5.2X20
99-211085Inductor, 9.8UH»mews

99-211073 Fuse, 2A, 125V

99-211086Inductor, 0.75MH211074inalBlock, 9CKT
99-211087inductor, 2.2UHian—_

4-24

Page 89

Hard Drivin’ Compact Itustrated Parts Lists

N O T E S

4-25

Page 90

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 91

Hard Drivin’ Compact Ilustrated Parts Lists

Hard Drivin’ Compact Main PCB Assembly Parts List

Designator Description Part No. Designator Description Part No.

Integrated Circuits70YIntegrated Circuit, 74AS08137484-001
5KIntegrated Circuit, 4464, 64K X 4,137546-00375CIntegrated Circuit, 7418259137137-001
DRAM75HIntegrated Circuit, 74LS14137056-001
5MIntegrated Circuit, 74F244137502-00180MIntegrated Circuit, 74A1S138137517-001
15BIntegrated Circuit, AD711KN137614-001
15KIntegrated Circuit, 4464, 64K X 4,137546-00385CIntegrated Circuit, 7418374137144-001
DRAM85, 85SIntegrated Circuit, VRAM, 64KX4,137553-002

150 nsec (Acceptable substitute is part

15MIntegrated Circuit, 74418245137440-001no. 137553-001, Integrated Circuit,
20PIntegrated Circuit, 74ALS574137548-001VRAM, 64KX4, 120 nsec.)
20S, 20U Integrated Circuit, 744S823137513-00185U, 85W IIntegrated Circuit, VRAM, 64KX4,137553-002
20WIntegrated Circuit, 74A$823137513-001150 nsec (Acceptable substitute is part

no. 137553-001, Integrated Circuit,

25KIntegrated Circuit, 4464, 64K X 4,137546-003VRAM, 64KX4, 120 nsec.)
DRAM90MIntegrated Circuit, 74ALSO8137460-001
25MIntegrated Circuit, 74A$573137547-001
30BIntegrated Circuit, 7418374137144-00195CIntegrated Circuit, 74LS374137144-001
30P,Integrated Circuit, 74L8245137134-00195P, 95SIntegrated Circuit, VRAM, 64KX4,137553-002

150 nsec (Acceptable substitute is part

30S, 30U Integrated Circuit, 2149, 45 nsec137199-002no. 137553-001, Integrated Circuit,
30WIntegrated Circuit, 2149, 45 nsec137199-002VRAM, 64KX4, 120 nsec.)
30YIntegrated Circuit, 7418245137134-00195U, 95W Integrated Circuit, VRAM, 64KX4,137553-002
35KIntegrated Circuit, 4464, 64K X 4,137546-003150 nsec (Acceptable substitute is pazt

DRAM no. 137553-001, Integrated Circuit, VRAM, 64KX4, 120 nsec.)

35MIntegrated Circuit, 74A18245137440-001100MIntegrated Circuit, 74418161137470-001
40HIntegrated Circuit, 741$123137268-001
40S, 40U Integrated Circuit, 2149, 45 nsec137199-002110¢Integrated Circuit, 7406137052-001
40wIntegrated Circuit, 2149, 45 nsec137199-002110KIntegrated Circuit, 74ALS138137517-001
120K,Integrated Circuit, 74F74137436-001
40¥Integrated Circuit, 7418245137134-001120KIntegrated Circuit, 7418393137146-001
45BIntegrated Circuit, ADC0809137243-001
50HIntegrated Circuit, 7418123137268-001120MIntegrated Circuit, 74ALS574137548-001
50S, 50U Integrated Circuit, 74418574137548-001120PIntegrated Circuit, 7448573137547-001

120S-PSP Integrated Circuit, 34012-50 137559-001

SowIntegrated Circuit, 74ALS574137548-001,120UIntegrated Circuit, 74F244137502-001
50YIntegrated Circuit, 74485733137547-001
SSL-MSPIntegrated Circuit, 34010-50137538-002120W, 120Y Integrated Circuit, 7448573137547-001
60BIntegrated Circuit, 7418244137038-001135C, 135H Integrated Circuit, 74F74137436-001
135KImegrated Circuit, 74AS32137487-001
60P, 60SIntegrated Circuit, VRAM, 64KX4,137553-002138M —_ Integrated Circuit, 741874137023-001

150 nsec (Acceptable substitute is part

no. 137553-001, Integrated Circuit,135PIntegrated Circuit, 7445573137547-001
VRAM, 64KX4, 120 nsec.)135UIntegrated Circuit, 74AS00137480-001
60U, 60W Integrated Circuit, VRAM, 64KX4,137553-002135WIntegrated Circuit, 7448573137547-001
150 nsec (Acceptable substitute is part135¥Integrated Circuit, 7418259137137-001

no. 137553-001, Integrated Circuit,

VRAM, 64KX4, 120 nsec.)140CIntegrated Circuit, 7418244137038-001
60YIntegrated Circuit, 7448138137522-001140HIntegrated Circuit, 7418393137146-001
65CIntegrated Circuit, 7418259137137-001140KIniegrated Circuit, 74Fi1137583-001
140MIntegrated Circuit, 741874137156-001
70P, 70SIntegrated Circuit, VRAM, 64Kx4,137553-002
150 nsec (Acceptable substitute is part140PIntegrated Circuit, 7418244137038-001
no. 137553-001, Integrated Circuit,140UIntegrated Circuit, 74AS08137484-001
VRAM, 64KX4, 120 nsec.)150CIntegrated Circuit, 7415245137134-001
70U, 70W Integrated Circuit, VRAM, 64KX4,137553-002150EIntegrated Circuit, 7418244137038-001

150 nsec (Acceptable substitute is part

no. 137553-001, Integrated Circuit,150H,Integrated Circuit, 741874137023-001
VRAM, 64KX4, 120 nsec.)150KIntegrated Circuit, 741S20137060-001
Page 92

Ilustrated Parts Lists Hard Drivin’ Compact

Hard Drivin’ Compact Main PCB Assembly, Continued Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPartNo.
1508-GSP Integrated Circuit, 34010-50137538-002205BIntegrated Circuit, 4066B137580-001
150U _ Integrated Circuit, 7448573137547-001210A _ Integrated Circuit, MC1488137403-001
150WIntegrated Circuit, 74F04137437-001210B—_Integrated Circuit, MC1489AL137263-001
150YIntegrated Circuit, 74F161137343-001210C, 210D Integrated Circuit, RAM, 8KXB,137535-006

150 nsec 1606 _ Integrated Circuit, 7418244 137038-001

160E_Integrated Circuit, 74A1S161137470-001210EIntegrated Circuit, 48Z02-15, RAM—_137442-150
160H_ Integrated Circuit, 7441832137464-001210F —_ Integrated Circuit, 7418245137134-001
160K —_ Integrated Circuit, 7418138137517-001210H, 210) Integrated Circuit, 7418244137038-001
210K’Integrated Circuit, 7418244137038-001
160MIntegrated Circuit, 74F04137437-001
160U_Integrated Circuit, 744532137487-0012101, 210M Integrated Circuit, 7418245137134-001
160WIntegrated Circuit, 741874137023-001210NIntegrated Circuit, 7418244137038-001
170CIntegrated Circuit, 7418245137134-001210P—_Integrated Circuit, 7418245137154001
210RIntegrated Circuit, EPROM136068-1101
170E —_ Integrated Circuit, 7418244137038-001137448-200

170H —_ Integrated Circuit, 7415148 137417-001

170K _ Integrated Circuit, 74A1S161137470-0012108Integrated Circuit, EPROM,136068-1103
175UIntegrated Circuit, 741874137023-001137448-200
210WIntegrated Circuit, EPROM,136068-1111
180C _ Integrated Circuit, 74A18138137517-001137448-200
180E —_ Integrated Circuit, 74ALS139137467-001210X _ Integrated Circuit, EPROM,136068-1113
185R_Integrated Circuit, 7418374137144-001137448-200
185T —_ Integrated Circuit, 7418193137128-001Capactoss
185U_Integrated Circuit, 7418374137144001SCeacior Murse ‘oeeaten
185WIntegrated Circuit, 741814137056-001C3C14Capacitor, 1 uP, 50 V, Ceramic425002108
190CIntegrated Circuit, 7418393137146-001CigCapacitor, 1 UF, 50 V, Ceramic122002104
190EIntegrated Circuit, 74AS00137480-001aisif
190KIntegrated Circuit, 68010137414-002C19-C21_Capacitor, .1 UF, 50 V, Ceramiccea
haeC24-C43Capacitor, .1 HF, 50 V, Ceramic122002-104
-I90NIntegrated Circuit, 7415245137134-001C4463Capacitor O41 hf, 50 V, 10%122015.102
195R —_ Integrated Circuit, 7418138137177-001C65-C78_Capacitor, 1 [IF, 50 V, Ceramic122002-104
195T —_ Integrated Circuit, 7418193137128-0011p PHB20%,
195UIntegrated Circuit, PROM, 828123136068-1168C79.Capacitor, 10 pF 100, Ceramic122016-100
i€80-C82Capacitor, .1 UF, 50 V, Ceramic122002-104
195WIntegrated Circuit, 74HC14137605-001j,
7C83, C84 Capacitor, 100 pF, 100 V, Ceramic122016-101
2004Integrated Circuit, 68681137543-001Cg5'c87Capacitor, 1 uF, 50 V, Ceramic—_122002-104
200C, 200D Integrated Circuit, RAM, 8KX8,137535-0061 oh HE208
150 nsecC94-C106 Capacitor, .1 UF, 50 V, Ceramic122002-104
200E—_Integrated Circuit, 48T02-15, RAM—_137540-150is ei ee cienal THE, 50 V; Ceramic122002-104
‘aapacitor, .1 UF, 50 V, Ceramic122002-104
200FIntegrated Circuit, 7418245137134-001C125-C128 Capacitor, 10 HF, 35 V, Electrolytic124000-106
200H, 200J Integrated Circuit, 7418244137038-001a0Hs 29 Me
200L’Integrated Circuit, 74A1S32137464-001129-137 Capacitor, .1 UR, 50 V, Ceramic125000404
200M—_Integrated Circuit, 74ALS138137517-001ra a? Capacitor, 1000 pF, 100 V, Ceramic122016-102
ia,pacitor, .1 UF, 50 V, Ceramic122002-104
200N, 200P Integrated Circuit, 7418245137134-001C12Capachion 24 uh 50%, Comemic—‘120015-224
200RIntegrated Circuit, EPROM,136068-1102a,,
137448-200,.,
_.143, C144 Capacitor, .1 WF, 50 V, Ceramic122002-104
2008bons ena EPROM,136068-1104 = Cy45,Capacitor, 10 uF, 35 V, Electrolytic124000-106

C146-C189 Capacitor, .1 UF, 50 V, Ceramic 122002-104

200WIntegrated Circuit, EPROM,sx606e-1112_©193-C202 Capacitor, 1, 50 V, Ceramic122002-104

137448-200 , .

—€204-C227 Capacitor, .1 UF, 50 V, Ceramic122002104
200XPrera EPROM,136068-111429gCapacitor, 001 [iF, 50 V, +10%122015-102

4-28

Page 93

Hard Drivin’ Compact Illustrated Parts Lists

Hard Drivin’ Compact Main PCB Assembly, Continued Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.
C229Capacitor, 47 pF, 100 V, Ceramic_-122016-470Crystals
230-238 Capacitor, .1 UF, 50 V, Ceramic122002-104XOSC1Oscillator, 32MHZ144008-002
243-249 Capacitor, .1 UF, 50 V, Ceramic122002-104XOSC2Crystal, 48 Mhz, Oscillator Module144008-003
C250Capacitor, 47 pF, 100 V, Ceramic122016470XOSC4Oscillator, 32MHZ144008-002
;XTALICrystal, 3.6864, Standup144000-011
251-259 Capacitor, .1 HF, 50 V, Ceramic122002-104Diodes
€264-27:itor,.1:i
200273 Capacitor, ot MF, 50 Y. Ceramic122002104CRI, CR2._Diode, MV5053, Light Emitting131027-002
27:Capacitor, 47 pF, 100 V, Ceramic122016-470CRSDiode. 1N4002131048-002
€275-C295 Capacitor, .1 HF, 50 V, CeramicT2200 WACRGDiode, MV5053, Light Emitting131027-002
298, C299 Capacitor, .1 UF, 50 V, Ceramic122002-104CRI, CRB’ Diode, IN4O2131048-002
©306-309 Capacitor, .1 HF, 50 V, Ceramic122002-104CR9-CR12. Diode, MV5053, Light Emitting131027-002
315-320 Capacitor, .1 HF, 50 V, Ceramic122002-104R13.Diode, 1N4002131048-002
€323-C326 Capacitor, 10 pF, 100 V, Ceramic——122016-100CRIdDiode, MVS053, Light Emitting431027-002
330-333 Capacitor, .1 UF, 50 V, Ceramic122002-104CRI8_Diode, 1N40021gn048-002
535, C536 Capacitor, 100 pF; 100 ¥, Ceramic122016-101ray_—_Diode, IN47A0A, 10 V, 5%, Zener151009-213
C341, C342 Capacitor, .1 WF, 50 V, Ceramic122002-104‘‘i
349-352. Capacitor, .1 JF, 50 V, Ceramic122002-104pertae ao Light Emittingbey ar

ie 1

354,C355 Capacitor, .1 WF, 50 V, Ceramic122002-104Transistors
C358Capacitor, .1 JF, 50 V, Ceramic122002-104Ql, Q2Transistor, 2N6044133042-001
359, C360 Capacitor, .001 [1F, 50 V, +10%122015-1023Integrated Circuit, 7905137581-001
C361-C363 Capacitor, 1000 pF, 100 V, Ceramic122016-1024Integrated Circuit, 7812137597-001
_fos)Transistor,2N3904133041-001

nsistor, ~( C364,C365 Capacitor, .1 JF, 50 V, Ceramic 122002-104

366Capacitor, 470 UF, 16 V, Electrolytic,123004-47726Transistor, 2N3906133040-001
RadialQTransistor, 2N3904133041-001
C367Capacitor, .1 MF, 50 V, Ceramic122002-104Q8Transistor, 2N3906133040-001
C368Capacitor, 10 UF, 20 V, Tantalum127002-106Q9Transistor, 2N3904133041-001
369-377 Capacitor, .1 JF, 50 V, Ceramic122002-104Qi0Transistor, 2N3906133040-001
378Capacitor, .001 (lF, 50 V, +10%122015-102Q11-Q13 Transistor, 2N3904133041-001
379Capacitor, .1 [F, 50 V, Ceramic122002-104Resistors
ConnectorsR1-R26 _ Resistor, 100 Q, +5%, 1/4 W110000-101
BCLKConnector, Rept, 2 Ckt179178-002R29-R45__Resistor, 1 K Q, +5%, 1/4 W110000-102
BCLKConnector, 4 Ckt, Header, 100 Cr179177-004R46-R48__Resistor, 470 Q, +5%, 1/4 W110000-471
jlConnector, 12 Circuit, Header .250 Ctr179069-012R49-R54Resistor, 4.7 K Q, +5%, 1/4 W110000-472
J256Connector, 11 Circuit, Header, .100 Ctr 179118-011R
55Resistor, 100 Q, 45%, 1/4 W110000-101
yConnector, Card Edge Header, 60179153-060Ror R6oResistor,1K Q, +5%, 1/4 W110000-102
Circuit, .2 CtrR61Resistor, 4.7 K Q, 45%, 1/4 W110000-472
J8J10Connector, 11 Circuit, Header, .100 CtrR62, R63 Resistor, 220 Q, £5%, 1/4 W110000-221

179118-011

yi2Connector, 9 Circuit, Header, .250 Ctr 179069-009ROBResistor, 1 K Q, +5%, 1/4 W110000-102
y13Connector, 11 Circuit, Header, .100 Cir 179118-011R70-R73__Resistor, 220 Q, 45%, 1/4 W110000-221

R74, R75. Resistor, 10 K Q, +5%, 1/4 W 110000-103

jiu4Connector, 26 Circuit, Header, .1 X .1 179261-026R76Resistor, 220 Q, +5%, 1/4 W110000-221

Dual

jasConnector, 16 Circuit, Header, .1 X .1 179261-016R77, R78 Resistor, 4.7 K Q, +5%, 1/4 W110000-472
DualR79Resistor, 47 K Q, 45%, 1/4 W110000-473
SPEEDConnector, Rept, 2 Chet179178-002R80, R81 Resistor, 1 K Q, £5%, 1/4 W110000-102
SPEEDConnector, 6 Ckt, Header, .100 Ctr179177-006R82, R83__ Resistor, 470 Q, 5%, 1/4 W110000-471
VCLKConnector, Rept, 2 Ckt179178-002R84-R88_Resistor, 10 K Q, +5%, 1/4 W110000-103
VCLKConnector, 6 Ckt, Header, .100 Ctr179177-006R89-R96Resistor, 33 Q, £5%, 1/4 W110000-330

4-29

Page 94

Alustrated Parts Lists Hard Drivin’ Compact

Hard Drivin’ Compact Main PCB Assembly, Continued. Parts List

Designator Description Part No. Designator Description Part No.

R9B-R101_ Resistor, 100 Q, £5%, 1/4 W110000-101R187_Resistor, 330 , 45%, 1/2 W110001-331
R102-R107 Resistor, 33 Q, +5%, 1/4 W110000-330R188Resistor, 1 K Q, 45%, 1/4 W110000-102
R109-R111 Resistor, 100 Q, +5%, 1/4 W110000-101R189—_—Resistor, 2.2MQ, #5%, 1/4 W110000-225
R113-R115 Resistor, 100 Q, 45%, 1/4 W110000-101R190Resistor, 10 K Q, £5%, 1/4 W110000-103
R116-R123 Resistor, 33 2, 45%, 1/4 W110000-330R191Resistor, 1 K @, #5%, 1/4 W110000-102
R124Resistor, 220 Q, 45%, 1/4 W110000-221R192_ Resistor, 270 K Q, +5%, 1/4 W110000-274
R125-R131 Resistor, 1 K Q, +5%, 1/4 W110000-102R193, R194Resistor, 1 K Q, £5%, 1/4 W110000-102
R132Resistor, 4.7 K Q, £5%, 1/4 W110000-472R197Resistor, 1 K Q, 45%, 1/4 W110000-102
RI34—_—_Resistor, 1 K Q, 45%, 1/4 W110000-102RNI1, RN2_ Resistor Network, 470X9, +5%, 1/8W,118010-471
R145, R146Resistor, 10 K Q, 45%, 1/4 W110000-103SIP (10 Pin)
R147, R14BResistor, 100 K Q, +5%, 1/4 W110000-104RN3-RNS. Resistor Network, R2R Ladder118015-001
R149, R1SOResistor, 10 K Q, +5%, 1/4 W110000-103RNG_ Resistor Network, 4.7KX9, 45%,118010-472

1/8 W, SIP (10 Pin) R151, R1S2Resistor, 220 , 45%, 1/4 W 110000-221 Sockets

R155.Resistor, 0, #5%, 1/4 W110005-001‘cet. 30-Pin,00",
R160, R1G1Resistor, 10 K , 45%, 1/4 W110000-103parentingEte
R162, R163Resistor, 150 Q, 25%, 1/4 W110000-151Socket, 28 Pin’ .600"179257-028

im 600"

R1G8-R171 Resistor, 10 K Q, $5%, 1/4 W110000-103Socket, 40 Pia, 600aed

R172, R173Resistor, 10 Q, £5%, 1/4 W 110000-100 Pi 1

R177, R178Resistor, 100 Q, 45%, 1/4 W110000-101Paced 4 iy aleel

R182-Ri84 Resistor, 10 K Q, 25%, 1/4 W 110000-103 : , Miscellaneous

R185Resistor, 1 K Q, +5%, 1/4 W110000-102swiSwitch, 8 Pos DIP160031-008
R186Resistor, 82 Q, 45%, 1/4 W110000-820Test Point179051-001

4-30

Page 95

Hard Drivin’ Compact

N Illustrated Parts Lists

)

Page 96

Illustrated Parts Lists Hard Drivin’ Compact

‘ ' i i —— DRIVER APU ATARI GAMES] F | 1 c22 ran ig Ie le + MADE _IN_USA ou FOF WN NNE TDAZO30 aL a2 TDA2Z030 g & Gao (7-000 = AO4e4434

i a] T sink 22,35v + is

Figure 4-11 Hard Drivin’ Compact APU PCB Assembly A044431-02 D

4-32

Page 97

Hard Drivin’ Compact Illustrated Parts Lists

Hard Drivin’ Compact APU PCB Assembly Parts List

DesignatorDescriptionPartNo._DesignatorDescriptionPart No.

Capacitors Transistors

aCapacitor, .1 WF, 50 V, Ceramic122002-104Q1,Q2Integrated Circuit, TDA2030137301-001
C2Capacitor, 22 UF, 50 V, Ceramic122015-224rorIntegrated Circuit, 7815, Standup__137598-001
3Capacitor, .1 UF, 50 V, Ceramic122002-104Resistors
caCapacitor, .001 WF, 50 V, Ceramic122002-102naResistor, 10K 0 3596 1/4.10000403
,.R2Resistor, 1, $5%, 1/4 W110000-010
csCapacitor, 22 HF, 50V, Ceramic122015-224RRA| ResisionDES, 250 UAWPenner
6Capacitor, 22 pF, 35 V, Electrolytic124000-226RSResistor, 1 K Q, +5%, 1/4 W110000-102
C7-C14_Capacitor, .1 HF, 50 V, Ceramic122002-104elaiais
C15-C18Capacitor, 3300 HIF, 25 V, Electrolytic, 123003-338RbResistor, 10, #5%, 1/4.W440000:100
RadialR7Resistor, 1 K , $5%, 1/4 W110000-102
;,RB,ROResistor, 22 K Q, 45%, 1/4 W110000-223
19Capacitor, .1 UF, 50 V, Ceramic122002-104R10Resistor 1, 4590, 1/4 W110000-010

C20, C21 Capacitor, 3300 HF, 25 V, Electrolytic, 123003-338 co Radial 1/4w 11 0-10:

o2Capacitor, 22 UE, 35 V, Electrolytic124000-226=Resistor, 10 K Q, 45%, 1/ep=tS
aCapacitor, 22 UE 50'V,,Ceramic122015224Connector, 2 On Henin 156 Cir179215-002
24Capacitor, .1 WF, 50 V, Ceramic122002-104Connector, 3 Ckt, Header, .156 Ctr179213-003
C25,Capacitor, .001 MF, 50 V, Ceramic122002-102Connector, 6 Ckt, Header, .156 Ctr179213-006
C26Capacitor, .22 UF, 50 V, Ceramic122015-224Connector, 9 Ckt, Header, .156 Ctr179213-009
C27Capacitor, -1 UF, 50 V, Ceramic122002104

Dindes HS1, HS2_ Heatsink, TDA2030 178190-032

CRI-CR6 Diode, 1N4001131048-001inHeatsink, 7612vyetpoa24

CR7-CR12. Diode, 1N5401 131051-002

4-33

Page 98

Alustrated Parts Lists Hard Drivin’ Compact

ov OU i a $23 ee “oat SP

ras]

Figure 4-12 Compact Hard Drivin’ Motor Amplifier PCB Assembly A046640-01 A

4:34

Page 99

Hard Drivin! Compact Illustrated Parts Lisis

Compact Hard Drivin’ Motor Amplifier PCB Assembly Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.

Capacitors

C1-CiCapacitor, 4700 HF, 25 V, Electrolytic, 123021-478Q8‘Transistor, MPSUS7133008-002
RadialQ9Transistor, IRF630133039-001
cSCapacitor, 100 UF, 16 V, Electrolytic124008-107Quo‘Transistor, IRF9640133037-001
C6, C?Capacitor, .1 UF, 50 V, Ceramic122002-104Hesisiare
C8,Capacitor, 1100V,r122016-e
Oo\pacitor, 1000 pF, 100 V, Ceramic — 122016-102RU, R2Resistor, 1 KQ,1.110030-102
CieCapacitor, 1 UF, 50 V, Ceramic122002-104R3Resistor, 4.7 KO, +5%, 1/4 W110000-472
cuCapacitor, .22 pF 50 V, Ceramic——-122022-224R4, RSResistor, 1.2 KO, #596, 1/4 W§10000-122
C12-C18Capacitor, -1 UF, 50 V, Ceramic122002-104R6Resistor, 2.4 KQ, 5%, 1/4 W110000-242
  • itor, i :
€24-C26Capacitor, .01 pF, 50 V, Ceramic122002-103R7,RBResistor, 2.2. KO, 45%, V4110000-222
027,28 Capacav.122002-10.ROResistor, 1 KO, 45%, 1/4 W110000-102
,’°’R11Resistor, 100 KQ, +5%, 1/4 W110000-104

Diodes

CRI-CR4 Diode, 1N5401131051-002RI2Resistor, 15 KQ, 45%, 1/4 W110000-153
CRS, CRG Diode, 1N5352B, £5%, Zener131049-220R13, R14 Resistor, 10 2, 45%, 1/4 W110000-100
cR?Diode, 1N4148131033-001RISResistor, 100 9, 45%, 1/4 W11000-1061
CR8, CRI Diode, 1N4747, Zener131009-220RISResistor, 10 KQ, +5%, 1/4 W110000-103
CRI10, CR11 Diode, IN5362, +59, Zener131049-230R18-R20__Resistor, 2.2 KQ, 45%, 1/4 W110000-222
R12, CRI3 Diode, 1N5401131051-002R24, R25 Resistor, 100 Q, +5%, 1/4 W110000-101
CR14, CRIS Diode, IN914131052-001R26Resistor, 0.5 Q, 5 W, Wirewound—_116029-5000
FusesR37Resistor, 5.6 KQ, +5%, 1/4 W110000-562
FULFuse, 4AMP, 250 V146007-4022rn
.dR38Resistor, 2.2 KQ, $5%, 1/4 W110000-222
FU2Fuse, 44MP, 250 V146007-4022RiResistor, 100 Q, 45%, 1/4 W110000-101
HeatsinksR41-R44Resistor, 150 Q, +5%, 1/4 W110000-15i
HTS1, HTS2 Heatsink, TDA2030178190-032R45Resistor, 190 Q, +5%, 1/4 W110000-101
HTS3Heatsink, Power Supply047084-01

R46, RAT Resistor, 10 KQ, 45%, 1/4 W 110000-103 Integrated Circuits

IclIntegrated Circuit, DAC-08137159-001__ Miscellaneous
IC3,IC4Integrated Circuit, 74ES174137122-001FU2, FU2-FU1Fuseclip179050-002
IC5Integrated Circuit, 7406137052-001FB1, FB2 Ferrite Bead141003-001
1C6Integrated Circuit, ADOPO7CN137523-001

yi Connector, 3 Circuit, Header, .156 Ctr 179213-003

aTransistors2Connector, 2 Circuit, Header, .250 Cir 179069-002
QiTransistor, 2N3904133041-00156Connector, 16 Circuit, Header,179261-016
3Transistor, TIP14S133046-001“1X 1 Dual
4‘Transistor, TIP140133047-001OPTiConnector, 6 Ckt, Header, .100 Ctr.179177-006
@‘Transistor, MPS-UO7, 100 V, 2.4133003-001
Page 100

Illustrated Parts Lists

ooo°0

Figure 4-13. Encoder Disk PCB Hard Drivin’ Compact

ooo0°o oO {Ss} }a| 0

Figure 4-14 Centering Disk PCB Assembly A046689-01 A A046691-01 B

Encoder Disk PCB Centering Disk PCB Assembly Parts List Parts List

Designator Description Part No. Designator Description Past No.

RL150Q, 1/4w, 5% Resistor110000-151RL220Q, 1/4W, 5% Resistor110000-221
OSR1NPN Out, Dual Slotted Opto-Sensor138000-001OSR1—_ NPN Out, Single Slotted Opto-Sensor 138001-001
yu4 Cki, .156 Ctr, Locking Connector—_79-58356jl4 Ckt, .156 Ctr, Locking Connector—_79-58356

4:36

Page 101

Hard Drivin’ Compact Illustrated Parts Lists

N O T E )

Page 102

Hard Drivin’ Statistics Sheet

—3——ipLaps—
Right Coins;Error Count:Champ Wins—_—_
|Aux Coins:Total Games:Jast Ros

lidle Mins: Rpi Aborts: Lay Track:

(Active Mins:ps by TradRpl Sec:—_—
rXtnded Plays:——Xtended Games by Track:Total Credits:
'1-X Games:—Avg Time/Credit:_
2X Games:No X Games by Track:8

IN-X Games: —_—

TimeNo. of GamesTimeNo. of GamesNo. of GamesNo. of Games
0-99180-199380-399|
100-119_200-219300-319400-419
120-139220-239—320-339420-439
140-159240-259340-359440-459—___-
160-179260-279-360-379460-UP
TimeMondayTuesdayWeduesday‘ThursdayFridaySaturdaySunday

[Midnight

  • {1:00 a.m.
Page 103

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 104

A

ATARI

GAMES

Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, CA 95035

&

bp &

> FT 0 tP