Mouse Trap 1st Edition
Mouse Trap (version 5) (Exidy, 1981) · Manual · 16 pages · 6 sections · original scan
MOUSE
TRAP
Operation and Service
Manual st Edition
1.0 INSPECTING MOUSE TRAP™M
All Exidy equipment is carefully packaged in well-padded cardboard containers to prevent damage during shipment. Before signing the delivery receipt, you should follow this procedure:
- Check for obvious damage and make certain that the physical piece count of the shipment matches the piece count on the bill of lading. These two procedures should always be done before signing the delivery receipt.
- Shortages and/or obvious damage to the packaging on any given shipment should be noted in writing on the delivery receipt before signing for the delivery.
- If concealed damage is suspected on any shipment, those packages believed to contain the damaged goods should be opened in the presence of the delivery driver. If the goods have sustained concealed damage, a description of said damage should be noted in writing on the delivery receipt before signing for the delivery.
- Never apply power to any game with noticeable damage.
1.1. FILING A CLAIM
To file a claim, follow this procedure:
- Any and all damaged freight, including packaging, should be retained by the consignee until a physical inspection of said freight can be made by a representative of the carrier involved.
- The Claims Manager for the carrier involved should be notified as soon as possible, after the damaged goods are received. Preferably, the carrier's Claims Manager should be notified within forty-eight (48) hours of receipt of the goods by the consignee.
- If warranted, a written claim should be filed with the carrier involved. A detailed description of the damage(s) should be provided and copies of all supporting documents, including bill of lading and/or delivery receipt, inspection report, and invoice, should be attached.
4, The sooner a claim is filed, the better for all parties concerned. The carrier against which a claim is filed is required, by law, to respond to (acknowledge) that claim within thirty
- days of receiving same and must reach a final disposition in the matter within one hundred twenty (120) days.
If no immediate cabinet damage is evident, perform the following visual inspection:
- Open each door with appropriate key.
- Examine each major and electrical component thoroughly for scrapes, dents, broken or missing parts and loose or missing screws.
- Check for loose cable connectors.
- Visually verify that all the integrated circuit devices (IC's) plugged into sockets are properly seated and that no IC pins are bent or misaligned.
If you find any damage during this inspection, file a claim with the carrier. Send a complete report of the damage to Exidy.
1.2. INSTALLATION
Planning the location of the game should involve both physical and_ electrical considerations. Such physical considerations concern the placement of the equipment with respect to these clearances:
Height: 71.75 inches Width: 25.25 inches Depth: 32.75 inches, Weight: 316 pounds
An indoor, relatively dust-free environment is necessary, with proper conditions required of any electrical component. Electrical considerations include availability of an AC outlet with the correct voltage. and frequency. Because MOUSE TRAPIM is designed for front access to all components, the only time you need consider access to the back is for monitor service.
1.3 CHECKOUT PROCEDURE
After properly inspecting and installing MOUSE TRAPIM, we suggest following this procedure to check its operation:
- Plug the AC jack into the AC outlet.
- Once powered up, after five seconds of silence, a quick beep sounding like an organ chord, is heard. This is part of the Exidy Audio Diagnostic Test. A single beep indicates all is well with the audio board. If more than one beep is heard, see the section on Self- Diagnostic Tests.
- Allow 8-10 seconds to pass for the CRT to warm up and Self-Diagnostic Tests to complete.
4 Observe the TV monitor display to assure the correct attract mode is present on the screen, described in the section on Normal Operation. If the MOUSE TRAP! display is incorrect, contact Exidy Customer Service Department.
- Insert the appropriate coin or token into either of the coin slots. All the messages in the attract mode will flash the following line:
PRESS PLAYER ONE START or PRESS ONE OR TWO PLAYER START
depending on the number of coins dropped into slot.
- Press one or two player start and play the game to verify that all screen images are displayed.
lf assistance or repairs are necessary, contact the Exidy Customer Service Department, (800) 538-8402.
INTRODUCING THE EXIDY OPERATOR CONVENIENCE PACKAGE Exidy's New Operator Convenience —_rate lock and key, securing game Package makes all components service to capable hands, and profits accessible through the front of the to the right hands! game. Each door has its own sepa-
To service speaker and lamp assembly, unhook top logo panel
Electronic Service Door Entire electronics assembly PCB's and power supply mounted on single slide-out metal panel. Separate lock and key, front access, and power interlock for safety. Operator DIP Switch easily accessible. To access electronics, unhook panel back latch, slide out unti! catch stops it, to insure board stays secure. May be serviced on location in pulled-out position, or at work bench by disconnecting harnesses, releasing catch, and lifting metal panel off Harnesses remain connected when sliding board out to catch position. To convert to 110 or 220 volt game, simply change connector. To service control panel, unhook latches by reaching through the Electronics Door. Control Panel swings down.
Concealed external ON/OFF switch. —
Coin Box Door Separate lock and key, front access, and power interlock
if 390 Java Drive Sunnyvale, CA 94086 Phone: (408) 734-9410, Telex: 357-499, switch for safety. Oversize Coin Box enclosed in strong, solid metal box inaccessible through any other door, for maximum security. Monitor Service Door Separate lock and key, power interlock switch for safety. In addition to front access to. monitor, this door is located in back of cabinet for easy access to monitor adjustments.
Route Operator Features Large, heavy-duty casters support full weight of game on pivot for one man ease of transportation. Two hand holds for easy grasping. Recessed AC cord storage, also a pivot point with foot. Skid rails to slide game onto ‘truck, spaced to line up in truck bed grooves to prevent sliding.
Coin Mech Door Separate lock and key, front access, and power interlock switch for safety. Lit coin-entry bezels. Accepts all standard coins and may be adjusted for tokens. Coin Meters mounted on separate bracket for easy reading. Operator selectable switches mounted on bracket for easy access. To service control panel, unhook latches by reaching through Coin Mech Door. Control pane! swings down. To remove monitor from front of game, unplug harness, slide out, release catch.
2.0 ADJUSTMENTS
2.1 POWER SUPPLY ADJUSTMENTS
All DC Power required to operate MOUSE TRAP is supplied by the Exidy Power Supply Module.
+5.00v DC +/- .25v
as measured on the Logic PCB near the microprocessor (location 2A). 2.2 SELECTABLE OPTIONS
MOUSE TRAPTM has several switch selectable options controlled by an 8position DIP switch located on the main logic board at position 16A. This switch is accessible through the front electronics door. Simply slide the logic board out and locate the DIP switch on the lower left-hand corner.
The following drawing shows the particular functions controlled by the 8-position DIP switch.
Coin Options
Number of Turns
Number of Turns
Coin Options
Coin Options
Bonus Points
Bonus Points
not used
Functions of the 8-position DIP Switch
2.3 SELECTABLE DIP SWITCH SETTINGS
MOUSE TRAP" jg shipped with the dip switch already set for optimum dollar return. Should you decide to change the settings, you may select any of the following options by setting the proper switch accordingly:
A. COINAGE Switch Switch Switch
| 4 | 5 | 8 | |
| 1 Coin - 1 Credit | OFF | OFF | OFF |
| 2 Coins- 1 Credit | OFF | ON | OFF |
| 1 Coin - 2 Credits | ON | OFF | OFF |
| 1 Coin - 4 Credits | ON | ON | OFF |
| 1 Coin - 3 Credits or | OFF | ON | ON |
2 Coins- 7 Credits
| 1 Coin in Left Slot- | OFF | OFF | ON |
1 Credit 1 Coin in Right Slot- 5 Credits
| One Coin in Left Slot- | ON | OFF | ON |
1 Credit 1 Coin in Right Slot- 4 Credits
| Two Coins in Left Slot- ON | ON | ON |
1 Credit 1 Coin in Right Slot- 3 Credits
B. NUMBER OF TURNS Switch Switch 6 7
| 2 turns | OFF | OFF |
| 3 turns | ON | OFF |
| 4 turns | OFF | ON |
| 5 turns | ON | ON |
E. BONUS TURN Switch Switch
| (Extra turn awarded | 2 | 3 |
when selectable number of points are made).
| Extra turn for | OFF | OFF |
30,000 points
| 40,000 | . | ON | OFF |
| 50,000 | OFF | ON | |
| 60,000 | ON | ON |
2.4 AUDIO BOARD ADJUSTMENTS
The illustration that follows points out the four audio adjustments and the location of the DIP switch. The audio board rides piggyback on the logic board, mounted on the left wall of the game, when viewed from the front service door.
DOG VOLUME
VOLUME VOLUME
MUSIC VOLUME
DIP SWITCH
3.0 SELF DIAGNOSTIC TESTS
MOUSE TRAP™ has two diagnostic test modes. The first mode, the Logic/Audio Diagnostic Test Mode, checks the RAM and ROM chips on the Logic Board, and simultaneously checks the Audio Board. This test mode is the normal self-test mode and is automatically performed when MOUSE TRAP™ ig first turned on. The second mode tests the Controls and Color only. To run this test, activate the coin switch while powering up. We will explain both of these modes in full detail.
You may bypass both diagnostic modes by depressing either player one or player two start button while powering up. After 8 seconds of the message "STAND BY VERSION X", (where X is a number) the Attract Mode appears.
3.1 LOGIC/AUDIO DIAGNOSTIC TEST MODE
The RAM Test
When MOUSE TRAP™ ig first turned on, a processor and video RAM test is done. If the RAM passes, it goes immediately into the ROM test, without a message indicating it passed the RAM test.
If a RAM chip fails, an attempt is made to indicate the RAM chip where a failure was detected. Since the screen depends on a properly functioning RAM, this indication may not be displayed. A failed RAM may be indicated by a digit from 0 to 7 in every position on the screen using four colors. The code for these digits is as follows:
Number on RAM chip Screen to check
5A Processor RAM
| 1 | 4A | failure |
| 2 | 8B | Screen RAM |
| 3 | 78 | failure |
4 11C
| 5 | 13C | Video RAM |
| 6 | 12€ | failure |
7 14C The RAM test cycles if the failure is persistent.
The ROM Test
If the RAM test passes, the ROM test begins. The message STAND BY VERSION X appears on the screen (where X is a number). One by one, exclamation points
- appear on the screen. Each exclamation mark indicates half (2K) of a ROM board chip, numbered 6A through 13A, has passed the diagnostic test. After all marks appear, the game then goes into the Attract Mode, indicating all is well.
If any failure is detected during the ROM test, a hex digit appears instead of an exclamation point with a “BAD ROM" message at the top of the screen. The test repeats indefinately if a bad ROM is encountered. The key for which chip to check is as follows:
Message: ROM Chip to check:
0 lower 2K of 11A 1 upper 2K of 11A
2 lower 2K of 10A 3 upper 2K of 10A
4 lower 2K of 9A 5 upper 2K of 9A
6 lower 2K of 8A 7 upper 2K of 8A
8 lower 2K of 7A 9 upper 2K of 7A
A lower 2K of 6A B upper 2K of 6A
The Audio Test
While the Logic tests are underway, the Audio board is also being checked.
Five seconds after power on, one or more quick beeps, like an organ chord, are heard. This is part of the Exidy Audio Diagnostic Test. The number of beeps that sound indicate different conditions of the Audio board.
The following code is an indication only, of where to first check the Audio Board. Because this diagnostic test only evaluates certain components, other circuitry is relied upon for the test. Should this other circuitry fail, the diagnostic test may not, then, point directly to the failure. Please use the results of this test as a guideline for further troubleshooting.
The code is as follows:
0 beep: If no beeps are heard, along with a hum or random notes, this may indicate a failure in 3A and/or 7A.
1 beep: All audio hardware is OK. However, be sure to check the Attract Mode Cycle anyway fora possible message to check the Audio Board. In occasional instances, this can occurs The message will further direct you.
2 beeps: ZERO PAGE RAM failure. Check 6532 RAM 1.0. Timer Array at location 7B on the board.
3 beeps: (will not occur)
4 beeps: ROM failure
5 beeps: INTERRUPT failure. Check 6532 at location 7B.
In addition, this message appears during power up only if the Audio Board needs to be checked:
AUDIO SELF TEST ERROR
or
AUDIO COMMUNICATION ERROR
3.2 CONTROL AND COLOR TEST MODE
\f desired, you may test all player controls and screen colors. To do so, activate either coin switch at power-up. The game then enters the Control/Color Test Mode. This mode lasts for seven minutes to give you time to test and make adjustments. After that, the Attract Mode begins.
In the Control/Color Test Mode, the screen shows this pattern:
COIN 1 COIN 2 PLAYER 1 PLAYER 2 DOG BUTTON RED BUTTON YELLOW BUTTON BLUE BUTTON
The grid pattern tests your screen for any distortion or convergence.
The solid blocks of color (red, white, green, and blue) allow you to adjust the color. When any player control (player 1 start, player 2 start, or red, blue, yellow, or Dog button) or coin switch (coin 1 or coin 2) is activated, its name appears below the white box. This shows that the switch connection is proper. When the joystick is activated, the message Joystick appears below the red box. Also, in the middle of the screen, a square indicates the joystick direction.
4.0 NORMAL OPERATION
4.1 ATTRACT MODE
After the MOUSE TRAP™ is powered up and the self- diagnostic test is performed, the Attract Mode starts up, showing the following messages:
MOUSETRAPTM
CREDITS 00
ONE COIN FOR ONE CREDIT
ONE CREDIT FOR ONE PLAYER TWO CREDITS FOR TWO PLAYERS
EXIDY
(P) COPYRIGHT 1981 (C)
The number of coins or any currency per game is operator selectable and the message will reflect that choice.
MOUSETRAP HALL OF FAME
| LWH | 49720 | INCREDIBLE |
| DJs | 47340 | FABULOUS |
| vic | 44130 | GREAT |
| MRK | 37830 | SUPER |
| HAI | 25650 | GOOD |
JOIN THE MOUSETRAP HALL OF FAME BY ENTERING YOUR INITIALS FOR A HIGH SCORE
At power up, this Hall of Fame contains ficticious high scores. The first player to exceed the lowest score may enter his score and initials. The Hall of Fame will show the high player's score until power is turned off, and then the ficticious scores reappear.
The following game instructions appear, in pictorial form: MOUSE EATS CHEESE, SURES BONES, TREA-
DOG EATS TREASURES CAT, CHEESE, BONES,
CAT EATS MOUSE
HAWK EATS MOUSE AND DOG
IN MAKES HAWK STUPID
BONE TURNS MOUSE INTO DOG WHEN YOU USE THE DOG BUTTON
A few seconds of game play is then shown and the Attract Mode cycle begins again.
4.2 Game Play
Despite many cats on the prowl, the player
steers a mouse through a playfield of halls
where the mouse chomps cheese for points and finds other red prizes for bonus value.
The mouse searches out dog bones which are accumulated at the top of the screen. Each bone allows the mouse to become a ferocious dog when the "dog button" on the control panel is pressed. Now the player is the aggressor, and cats are open game for additional points of escalating value. After several seconds, the red dog begins blinking blue. This warns that his power is wearing off and he'll soon be a mere mouse again.
When all the cheese morsels on one level are eaten up, the player is given another game field with more challenge.
Randomly, a purple hawk flies over the walls in search of a delicious mouse or dog. The player's only defense is to enter the secret passage marked "in" at the center of the screen. This quickly transports the mouse or dog through an unseen tunnel to one of the four corners. This tactic makes the hawk "dumb", or aimless in his flight. The mouse or dog can then escape the hawk.
The player has the added strategy of doors to open and shut to his advantage. At the touch of a button, the player may open or close three colors of doors. By closing a door, the mouse can block a cat's advance. Or, when the mouse turns into a dog, the skilled player can use the doors to trap cats, earning additional points of escalating value for each one overtaken.
4.3 BONUS TURN FEATURE
An extra turn is given to a player everytime he scores 30,000, 40,000, 50,000, or 60,000 (operator selectable) points. A good player may rack up any number of bonus turns throughout a game, but the screen does not display more than five. 4.4 ENTERING THE MOUSE TRAP™M HALL OF FAME
Anytime a player's score exceeds one of the
five current high scores, he is eligible to enter his initials in the Vanity Table. If both players of a two player game are record high scorers, the highest of the two is first invited to enter his initials. To do so, he directs the mouse around an alphabet chart with the joystick. Once on the letter desired, he hits the DOG button. The RUB feature allows a player to erase mistaken letters. Once the correct initials are keyed in, the player should go to END, and hit the DOG button. This will log in his initials, and return to the next mode.
The Hall of Fame Mode runs ona timer. If a player does not enter his or her initials , the Attract Mode eventually takes over.
aay
LOGIC BOARD ASSEMBLY PARTS LIST
PART NUMBER DESCRIPTION
177-3391-14 Logic PCB Assembly 77-3391-14 Logic PCB 58-0002-00 Spacer 22-0001-02 1.C. 74LS00 22-0002-02 1.C. 74LS02 22-0003-02 1.C. 74LS04 22-0004-00 1.C. 7407 22-0005-02 1.C. 74LS08 22-0006-02 1.C. 74LS11 22-0007-02 1.C. 74LS20 22-0008-02 1.C. 74LS21 22-0009-02 1.C. 74LS27 22-0010-02 1.C. 74LS32 22-0011-02 1.C. 74LS74 22-0012-02 1.C. 74LS112 22-0013-02 1.C. 7418138 22-0214-02 1.C. 7418139 22-0015-02 LC. 7418157 22-0016-02 1.C. 74LS161 22-0017-02 1.C. 74LS166 22-0018-02 1.C. 7415193 22-0019-02 1.C. 7418241 22-0020-02 1.C. 74LS245 22-0021-02 1.C. 74LS374 25-0001-00 1.C. MICROPROCESSOR 6502A 23-0001-00 6301 PROM 23-0002-00 6331 PROM 23-0003-00 6331 PROM 20-0001-00 IN4002 DIODE 02-4712-00 RESISTOR, 470 OHM 1/4W 5% 02-1222-00 RESISTOR, 1.2K 1/4W 5% 02-2222-00 RESISTOR, 2.2K 1/4W 5% 02-3322-00 RESISTOR, 3.3K 1/4W 5% 09-2212-00 RESISTOR, 220 OHM 1/8W 5% 10 PIN SIP 09-2222-00 REISTOR, 2.2K 1/8W 5% 10 PIN SIP 09-4722-00 RESISTOR, 4.7K 1/8W 5% 10 PIN SIP 09-6822-00 RESISTOR, 6.8K 1/8W 5% 10 PIN SIP 41-0001-00 CONNECTOR, PCB FEMALE 10-1034-1 CAPACITOR, .01 UF CERAMIC DISC 10-1044-1 CAPACITOR, .1 UF CERAMIC DISC 11-6853-0 CAPACITOR, 6.8 UF 25V DIPTANT 40-0004-00 CONNECTOR, PCB MALE 13-4775-0 CAPACITOR, 470UF 10V ELECTROLYTIC 47-0001-00 DIPSHUNT JUMPER PAKS 16 PIN 49-5002-00 DIP SWITCH 8 POSITION 29-0001-00 CRYSTAL 11.289MHZ (SERIES) 44-1601-00 DIP SOCKETS 16 PIN LOW PROFILE 44-2401-00 DIP SOCKETS 24 PIN LOW PROFILE 44-4001-00 DIPSOCKETS 40 PIN LOW PROFILE 44-1401-00 DIP SOCKETS 14 PIN LOW PROFILE 44-1801-00 DIP SOCKETS 18 PIN LOW PROFILE 11-1053-00 CAPACITOR 1UF 25V DIPTANT 02-2212-00 RESISTOR, 220 OHM 1/4W 5%
LOGIC BOARD ASSEMBLY PARTS LIST (continued)
PART NUMBER
02-1802-00 10-3314-4 02-4732-00 11-1063-00 23-0004-00 23-0005-00 23-0006-00 02-1822-00 02-2272-00 02-1052-00 27-0003-00 20-0006-00 23-0014-00 23-0015-00 23-0016-00 23-0017-00 23-0018-00 DESCRIPTION
RESISTOR, 18 OHM 1/4W 5% CAPACITOR, 330PF CERAMIC DISC RESISTOR, 47K 10UF 16V DIPTANT 2732, EPROM 2716, EPROM 2114 STATIC RAM RESISTOR, 1.8K 1/4W 5% RESISTOR, 2.7K 1/4W 5% RESISTOR, 1M 1/4W 5% I.C., OSC NE555 DIODE, 4454 2732, EPROM 2732, EPROM 2732, EPROM 2732, EPROM 2732, EPROM
AUDIO/COLOR BOARD ASSEMBLY
PART NUMBER
177-3392-14 77-3392-14 22-0013-00 26-0001-00 22-0023~-00 22-0003-02 22-0001-02 22-0021-02 22-0024-00 22-0025~-00 22-0011-02 22-0026-00 22-0027-02 22-0028-00 22-0014-02 22-0029-02 22-0030-02 22-0031-02 10-1044-1 10-2204-1 10-1034-1 13-3365-1 13-1075-00 13-4755-00 02-3332-00 02-3322-00 02-1062-00 02-3012-00 02-1802-00 02-2232-00 02-2722-00 DESCRIPTION
AUDIO/COLOR PCB ASSEMBLY AUDIO/COLOR PCB LC. 7415138 1.C. 6520-A Lc. 4069 IC. 741804 1.C. 74LS00 1.C. 7418374 LC. 4053 IC. 4175 IC. 741874 1.C. LM324 1.C. 74/586 1.C. 4051 IC. 74LS139 1.C. 7418148 LC. 7415151 LC. 7418174 CAPACITOR, «1 UF CERAMIC CAPACITOR, 22PF 16V CERAMIC CAPACITOR, .O1UF 16V CERAMIC CAPACITOR, 33UF 25V ELECTROLYTIC CAPACITOR, 100UF 16V ELECTROLYTIC CAPACITOR, 4.7UF 16V ELECTROLYTIC RESISTOR, 33K 1/4W 5% RESISTOR, 3.3K 1/4W 5% RESISTOR, 10M 1/4W 5% RESISTOR, 300 OHM 1/4W 5% RESISTOR, 18 1/4W 5% RESISTOR, 22K 1/4W 5% RESISTOR, 2.7K 1/4W 5%
AUDIO/COLOR BOARD ASSEMBLY (continued)
PART NUMBER
02-1322-00 02-6812-00 02-3312-00 02-1612-00 02-8202-00 02-3902-00 02-1032-00 07-1034-00 29-0002-00 47-0001-00 44-1401-00 44-2401-00 44-2801-00 44-4001-00 44-1601-00 02-4712-00 02-2422-00 02-2032-00 02-1832-00 02-3922-00 02-2452-00 22-0039-00 23-0007-00 23-0008-00 23-0009-00 23-0010-00 27-0003-00 22-0033-00 27-0004-00 22-0034-00 40-0003-00 22-0037-00 22-0015-00 22-0010-00 22-0038-00 25-0003-00 22-0035-00 22-0036-00 02-2732-00 84-0014-00 14-2044-00 10-1024-00 09-0001-00 09-0002-00 21-0001-00 21-0002-00 14-2224-00 23-0011-00 23-0012-00 23-0013-00 40-0004-00 25-0002-00 DESCRIPTION
RESISTOR, 1.3K 1/4W 5% RESISTOR, 680 OHM 1/4W 5% RESISTOR, 330 OHM 1/4W 5% RESISTOR, 160 OHM 1/4W 5% RESISTOR, 82 OHM 1/4W 5% RESISTOR, 39 OHM 1/4W 5% RESISTOR, 10K 1/4W 5% 10K POT 3.579545 MHZ CRYSTAL 16 PIN DIP SHUNT 14 PIN DIP SOCKET 24 PIN DIP SOCKET 28 PIN DIP SOCKET 40 PIN DIP SOCKET 16 PIN DIP SOCKET RESISTOR, 470 OHM 1/4 RESISTOR, 2.4K 1/4W RESISTOR, 20K 1/4W RESISTOR, 18K 1/4W RESISTOR, 3.9K 1/4W RESISTOR, 2.4M 1/4/W 1.C. 74LS42 2732 EPROM 2732 EPROM 2732 EPROM 2732 EPROM NE555 OSC. TLO81 OP/AMP MC3417L DELTA MOD 4006 CMOS SHIFT REG. 6 PIN MALE CONNECTOR .156 CENTER 1.6C. 74LS125 LC. 74LS157 1.C. 74LS32 1.C. 74LS367 280 CPU 4070 CMOS EXC. OR GATE LM741EN OP/AMP RESISTOR, 27K OHM 1/4W HEATSINK, THM6045 CAPACITOR, MYLAR .2UF 16V CAPACITOR, CERAMIC .OO1UF 16V RESISTOR, 1.8K SIP PAC 8 PIN RESISTOR, 4.7K SIP PAC 8 PIN NPN TRANSISTOR TIP 120 PNP TRANSISTOR, TIP 125 CAPACITOR, MYLAR .0022 UF 2716, EPROM 2716, EPROM 2716, EPROM CONNECTOR, PCB MALE 1.C. 6532
AUDIO/COLOR BOARD ASSEMBLY (continued)
PART NUMBER
25-0001-00 27-0001-00 22-0022-02 27-0002-00 41-0001-00 130-0001-00 30-0001-00 46-1003-00 46-0004-00 45-0003-00 37-0001-00 45-0005-00 132-0001-00 177-3365-14 DESCRIPTION
1.C. 6502 1.C. 6840 1.C. 74LS154 1.C. 8253 CONNECTOR, PCB FEMALE ASSEMBLY, FILAMENT X-FORMER X-FORMER FILAMENT HOUSING, 3 PIN FEMALE HOUSING, 4 PIN MALE TERMINAL, .09 MALE TYRAP TERMINAL, .09 FEMALE ASSEMBLY, 5V POWER SUPLY UNIVERSAL POWER SUPPLY ASSEMBLY