Tempest Troubleshooting Guide TM-195 2nd Printing
Tempest (rev 3, Revised Hardware) (Atari, 1980) · Troubleshooting · 28 pages · 31 sections · original scan
TROUBLESHOOTING GUIDE eS) Complete with Signatures
and Memory Map
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Complete with Signatures and Memory Map
Copyright © 1981 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
The Tempest™ game play, all graphic designs, this troubleshooting guide, the technical manual, its accompanying schematic diagrams, and the monitor manual are protected by the new Copyright Act of 1976.
This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. if infringers are convicted, courts can order destruction of the infringing articles.
In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys' fees, fines up to $25,000, and face an imprisonment of up to one year.
Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by: ATARI INC. 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086
Reproduced in the U.S.A. 10K
Table of Contents
3 Troubleshooting Using the CAT Box....... CAT Box Preliminary Sere went ss eet HE Address and Data Lines . RAM ...........005 Option Switch Inputs . Custom Audio /O Chips ............. Player Input Switches and Encoder Wheel LED and Coin Counter Outputs....... Om7NnovoOWp
4 Jraubiesoating with Signature Analysis Signature Analysis Set-up Address Lines .... Address Decoder . . ROM and Data Lines . Math Box MOOD>
List of Illustrations
Figure 1 Memory Map.... Figure 2. Address and Data Lines. . Figure 3 Custom Audio l/O Chips ..... Figure 4 Led and Coin Counter Addresses
Figure 5 Analog Vector-Generator Data. . . Figure6 S.A. Harness Assembly .. Figure7 S.A.HarnessAssembly............ 000. eee eae AARWONND
iii
WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service
Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) roy From California, Alaska or Hawaii (408) 745-2900 ro” From anywhere else in this area toll-free (800) 538-1611
EAST U.S.A. Game sales and service only
Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey Oy (201) 469-5993 zs From anywhere else in this area toll-free (800) 526-3849
EUROPE Parts for all Atari customers in Western Europe. Game sales and service
Atari Ireland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland IRELAND Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT)
@ 06252155
1 Memory Map
MEMORY MAP
HEXA. DECIMAL | RW DATA FUNCTION ADDRESS D7 D6 D5 D4 D3 D2 D1 DO
| 0000:7FFF | |RW|D D D | D D D OD _ OD | Program RAM (2k) | ||
| 0800-080F | Ww | D D D_ OD | Color RAM | ||
| ocoo | R | D | Right Coin Switch | ||
| 0Co0 | R | D | Center Coin Switch | |
| coo | R | D | Left Coin Switch | |
| coo | R | D | Slam Switch | |
| 0co0 | R | D | SelfTest Switch | |
| 0coo | R | D | Diag.Step Switch | |
| coo | R | D | HALT | |
| ocoo | R|D | 3KHz | ||
| oD90 | R|}D DD | D D D D | Dj | Option Switch Inputs |
| E00 | R | DB DD | D DBD D OD 2D} | Option Switch Inputs |
| 2000-2FFF | |RW) D D D | D D D OD OD} | Vector RAM (4K) | |
| 3000-3FFF | R|O DB D | DD D OD D |} Vector ROM (4K) | ||
| 4000 | WwW | D | Right Coin Counter | ||
| 4000 | Ww | D | Center Coin Counter | |
| 4000 | Ww | D | Video Invert X | |
| 4000 | Ww | D | Video Invert Y | |
| 4800 | Ww | VG GO | ||
| 5000 | Ww | WD CLEAR | ||
| 5800 | Ww | VG Reset | ||
| 6000-603F | w}]}D DD DD D | OD OD, EAROM Write | ||
| 6040 | w}]}D D DD D D | D_ OD} | EAROM Control | |
| 6040 | R|D | Math Box Status | ||
| 6050 | R|O0 D DD D D | D OD} | EAROM Read | |
| 6060 | R|O D DD D D D | OD} | Math Box Read | |
| 6070 | R}0 D DD D D D_ | OD} | Math Box Read | |
| 6080-609F | |W] | D D D D D DO D_ | Dj| Math Box Start |
60C0-60CF |RW|D D D D D D D_ OD | Custom Audio Chip 1 60D0-60DF |RW)D D D D D D OD Dj Custom Audio Chip 2
| 60E0 | R | D | One Player Start | |
| 60E0 | R | D | Two Player Start |
| 60EO | R | FLIP |
9000-DFFF | R | D D D D D D OD _ Dy} Program ROM (20k)
Figure 1 Memory Map
2 Watchdog
The Watchdog circuit will cause continuous reset pulses to the microprocessor if a problem exists within the microprocessor circuit. If the self-test fails to run, it is a good practice to check the reset line.
RESET-microprocessor input (pin 40). In a properly operating game, reset should occur during Power-up or when the reset push button is activated. A pulsing reset line indicates that something is causing the microprocessor to lose its place within its program. Typical causes are: . Open or shorted address or data bus lines . Bad microprocessor chip . Bad bus buffers Bad ROM Bad RAM . Any bad input or output that causes an address or data line to be held in a constant high or low state ONaRONa
A pulsing RESET signal indicates a problem exists somewhere within the microprocessor circuitry rather than within either the Math Box or the Analog Vector Generator.
- Troubleshooting
Using the CAT Box
A. CAT Box Prelim-
A. CAT Box Prelim inary Set-up
- Remove: @ The electrical power from the game. @ The wiring harnesses from the game PCBs. @ The main and auxiliary boards from the game cabinet.
e ne microprocessor chip C2 from the main
B.
- Connect: @ The harnesses from the game to the main and auxiliary boards. (Use extender cables if available.) 00 ando2 test points together. W DOG DIS test point to ground. The CAT Box flex cable to the main PCB test edge connector.
- Power Up: @ The game. @ The CAT Box.
- Set CAT Box Switches: @ TESTER SELF-TEST: (OFF) @ TESTER MODE: RW @ Press TESTER RESET
B. Address and Data Lines
- Perform the CAT Box preliminary set-up.
- Connect the DATA PROBE to the CAT Box and the game ground test point.
- TESTER MODE: R/W
BYTES: 1. . PULSE MODE: UNLATCHED . R/W MODE: (OFF) RW to WRITE . Key in address pattern on the keyboard (use AAAA to start)
- Push DATA SET
- Key in data pattern on the key board (use AA to start)
- R/W MODE: STATIC
- Probe the IC-pin with the data probe and check for the 1 or 0 LED as indicated in Figure 2. Repeat this step for each address and data line.
- Repeat steps 6-11 using 5555 in step 8 and 55 in step 10. ONOMA
Figure 2 Address and Data Lines
| When writing | Address and | When writing |
| AAAA pattern | data lines | 5555 pattern |
| Logic State | IC-Pin | Logic State |
| 1 | B3-1 | 0 |
| 0 | B3-3 | 1 |
| 1 | B3-2 | 0 |
| 0 | AIB-3 | 1 |
| 1 | AIB-18 | 0 |
| 0 | AIB-16 | 1 |
| 1 | AIB-14 | 0 |
| 0 | AIB-12 | 1 |
| 1 | BIC-3 | 0 |
| 0 | BIC-5 | 1 |
| 1 | BIC-7 | 0 |
| 0 | BIC-9 | 1 |
| 1 | BIC-18 | 0 |
| 0 | BIC-16 | 1 |
| 1 | BIC-14 | 0 |
| 0 | BIC-12 | 1 |
| 1 | F2-9 | 0 |
| 0 | F2-8 | 1 |
| 1 | F2-7 | 0 |
| 0 | F26 | 1 |
| 1 | F25 | 0 |
| 0 | F2-4 | 1 |
| 1 | F23 | 0 |
| 0 | F2.2 | 1 |
Cc. KAM
- Perform the CAT Box preliminary set-up.
- Set the CAT Box switches as follows: a. Press TESTER RESET b. DBUS SOURCE: ADDR c. BYTES: 1024 d. R/W MODE: (OFF) e. R/W: WRITE f. Enter 0000_on the keypad g. Toggle R/W MODE to PULSE and back to (OFF) h. R/W: READ i. Toggle R/W MODE to PULSE and back to (OFF)
- If the CAT Box reads an address that doesn’t compare, the COMPARE ERROR LED lights up, the ADDRESS/SIGNATURE display shows the failing address location, and the ERROR DATA DISPLAY switch is enabled. Using this switch, determine if the error is in the high- or low-order RAM.
4, Repeat the test with DBUS SOURCE set to ADDR.
- Repeat steps 2-4, entering 0400 on the keypad (step f).
- Repeat steps 2-4, entering 2000 on the keypad (step f).
- Repeat steps 2-4, entering 2400 on the keypad (step f).
- Repeat steps 2-4, entering 2800 on the keypad (step f).
- Repeat steps 2-4, entering 2C00 on the keypad (step f).
D. Option Switch Inputs
. Perform the CAT Box preliminary set-up. BYTES: 1 R/W: READ . R/W MODE: (OFF) . _Key in 0D00 R/W MODE: STATIC . Activate the option switches at location N13 while monitoring the DATA DISPLAY. The DATA DISPLAY will change if the switches are operating properly.
- Repeat steps 4-7, entering OE00 in step 5, and activate switches at location L12. NOgaRONM
E. Custom Audio
1/O Chips
- Substitute good part for defective part.
- Use the procedure that follows.
. Perform the CAT Box preliminary set-up. BYTES: 1 RIW: WRITE RW MODE: (OFF) Enter address from Figure 3 . Press DATA SET . Enter the data from Figure 3 R/W MODE to PULSE and back to (OFF) . Repeat steps 5-8 for each address and data, noting the test results. CPNOTASNS
Figure 3 Custom Audio I/O Chips
| ADDRESS | DATA | TEST RESULTS | ADDRESS | DATA | TEST RESULTS |
| 60CF | 00 | 60DF | 00 | ||
| 60CF | 03 | 60DF | 03 | ||
| 60C0 | 55 | 60D0 | 55 | ||
| 60C1 | AF | Custom Audio I/O Chip | 60D1 | AF | Custom Audio I/O Chip |
#1 channel 1 produces #2 channel 1 produces pure tone. pure tone.
| 60C1 | 00 | Custom Audio I/O Chip | 60D1 | 00 | Custom Audio I/O Chip |
#1 channel 1 off. #2 channel 1 off.
| 60C2 | 55 | 60D2 | 55 | ||
| 60C3 | AF | Custom Audio I/O Chip | 60D3 | AF | Custom Audio I/O Chip |
#1 channel 2 produces #2 channel 2 produces pure tone. pure tone.
| 60C3 | 00 | Custom Audio I/O Chip | 60D3 | 00 | Custom Audio YO Chip |
#1 channel 2 off. #2 channel 2 off.
| 60C4 | 55 | 60D4 | 55 | ||
| 60C5 | AF | Custom Audio I/O Chip | 60D5 | AF | Custom Audio VO Chip |
#1 channel 3 produces #2 channel 3 produces pure tone. pure tone.
| 60C5 | 00 | Custom Audio /O Chip | 60D5 | 00 | Custom Audio I/O Chip |
#1 channel 3 off. #2 channel 3 off.
| 60C6 | 55 | 6006 | 55 | ||
| 60C7 | AF | Custom Audio I/O Chip | 60D7 | AF | Custom Audio VO Chip |
#1 channel 4 produces #2 channel 4 produces pure tone. pure tone.
| 60C7 | 00 | Custom Audio I/O Chip | 60D7 | 00 | Custom Audio l/O Chip |
#1 channel 4 off. #2 channel 4 off.
F. Player Input Switches and Encoder Wheel
. Perform the CAT Box Preliminary Set-up . DBUS SOURCE to DATA . BYTES: 256 RWW: WRITE R/W MODE: (OFF) . Key in 60D0 . Press DATA SET . Key in 00_ ). Toggle R/W MODE to PULSE and back to (OFF) . BYTES: 1 . RW: READ . Key in 60D8
- RAW MODE: STATIC . Pushing the following player input switches should cause the DATA DISPLAY to change: FIRE, SUPERZAPPER, 1-player start and 2-player start. (Also Player-2 FIRE and Player-2 SUPER- ZAPPER in cocktail* games.) PORASSCMNODAwWNs
*To test player-2 inputs in cocktail games connect IC D6-1 to +5.
G. LED and Coin Counter Outputs
. Perform the CAT Box Preliminary set-up. DBUS SOURCE to DATA BYTES: 1 RIW: WRITE RW MODE: (OFF) Key in address from Figure 4 . Press DATA SET Key in on or off data from Figure 4 . R/W MODE to STATIC and back to (OFF) . Repeat steps 6-9 to turn off coin counter solenoids, or to test another address. SePNODAwNS =
If you write data that activates a solenoid, deactivate it by pressing the reset button on the game board or by writing “off” data. If you leave a solenoid activated for more than about 10 seconds it will overheat and may have to be replaced. Figure 4 LED and Coin Counter Addresses
ADDRESS ON-DATA = OFF-DATA = OUTPUT NAME.
| 4000 | 01 | 00 | Right Coin Counter |
| 4000 | 02 | 00 | Center Coin Counter |
| 4000 | 04 | 00 | Left Coin Counter |
| 60E0 | —D | FE | 1-player start LED |
| 60E0 | FE | FF | 2-player start LED |
H. Analog Vector-
H. Analog Vector Generator
- Test: . Perform CAT Box preliminary set-up. . DATA SOURCE: DATA RW: WRITE RIW MODE: (OFF) Key in address from Figure 5 or press AD- DRESS INC. . Press DATA SET . Key in data from Figure 5 . Set RW MODE to PULSE and then to (OFF) . Repeat steps 5-8 for each address in Figure 5 WOND MARWONS
- RW: READ
- RW MODE: (OFF) 12, Key in address or press ADDRESS INC.
- RW MODE: PULSE
- Check the data in the DATA DISPLAY against the data in Figure 5
If you are sure the data is correct, proceed to steps 15-19:
- RW MODE: WRITE
- RW: (OFF)
- Key in VG GO address (4800 for TEMPEST™)
- R/W to PULSE and then back to (OFF)
- After writing to the VG GO address, the monitor should show a large plus sign. Failure of the horizontal or vertical circuits shows up as a single line drawn on the monitor. /f your monitor does not display a large pilus sign, contact Atari Field Service.
Figure 5 Analog Vector-Generator Data
Address Data Address Data Address Data
| 2000 | 40 | 200C | FF | 2018 | 00 |
| 2001 | 80 | 200D | 03 | 2019 | 40 |
| 2002 | 00 | 200E | 00 | 201A | 80 |
| 2003 | 70 | 200F | 62 | 201B | 00 |
| 2004 | 00 | 2010 | 40 | 201C | 80 |
| 2005 | 1E | 2011 | 80 | 201D | 1F |
| 2006 | 00 | 2012 | 80 | 201E | 00 |
| 2007 | 1E | 2013 | 00 | 201F | 00 |
| 2008 | 00 | 2014 | 00 | 2020 | FF |
| 2009 | 60 | 2015 | 00 | 2021 | 40 |
| 200A | FF | 2016 | 01 | 2022 | 00 |
| 200B | 03 | 2017 | 1F | 2023 | Eo |
4 Troubleshooting
With Signature Analysis
A. Signature Analysis Set-up
Perform the CAT Box Preliminary set-up.
Connect the three BNC to E-Z clip cables (supplied with the CAT Box) to the SIGNATURE ANALYSIS CONTROL START, STOP and CLOCK jacks on the CAT Box.
Attach the three black E-Z clips to a ground loop on the Tempest™ game PCB.
Attach the CAT Box data probe to the DATA jack on the CAT Box. The colored E-Z clips on the cables will be moved about for each group of signatures to be taken.
Set the CAT Box switches as follows: TESTER MODE: SIG TESTER SELF-TEST: OFF PULSE MODE: LATCHED START: As indicated STOP: As indicated CLOCK: As indicated e@eeoeoeoee
Power up the game board and the CAT Box.
B. Address Lines
- CAT Box Settings for Address Bus Test
| Probe | Trigger | IC-Pin | Test Pt. |
Probe Trigger IC-Pin Test Pt Start Lh AG-3
| Stop | Lu | A6-3 | |
| Clock | L | 02-39 | 02 |
Verify CAT Box settings and connections as follows:
- probe GND test point = 0000 signature
- probe + 5V test point = 0001 signature
- Signatures
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
BiC1-12 ABO UUUU
| BIC1-14 | ABI | 5555 |
| BIC1-16 | AB2 | cccc |
| BIC1-18 | AB3 | 7F7F |
| BIC1-9 | AB4 | 5H21 |
| BIC1-7 | ABS | OAFA |
BIC1-5 AB6 UPFH
| BIC1-3 | AB7 | 52F8 |
| AIB1-12 | AB8 | HC89 |
| AIB1-14 | ABO | 2H70 |
| AIB1-16 | AB10 | HPPO |
| AIB1-18 | ABI | 1293 |
| AIB1-3 | AB12 | HAP7 |
| B3-2 | A13 | 3096 |
| B3-3 | Al4 | 3827 |
| B3-1 | AIS | 755U |
| AG-4 | A1S | 755P |
C. Address Decoder
- CAT Box Settings for Address Decoder Test
| Probe | Trigger | IC-Pin | Test Pt. |
| Start | 1 | A6-3 | |
| Stop | Lh | AG-3 | |
| Clock | kL | o2 |
- Signatures
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| B37 | vO. | F2A6 |
| E3-2 | om | F2A7 |
| F3-8 | EVO | F2A6 |
| J5-9 | VGRST | 5969 |
| J5-10 | WODCLR | OPCS |
| J5-11 | VGGO | 270P |
| J5-12 | BB* | 9CH2 |
| B3-5 | VMEM | 12U3 |
| B3-4 | AA‘ | 4POA |
| J2-7 | ROM8 | 56C3 |
| J2-6 | ROM7 | 8019 |
| J2-5 | ROM6 | 5AH1 |
| J2-4 | ROMS | 9HUC |
| J2-9 | ROM4 | 1920 |
| J2-10 | ROM3 | C34C |
| J2-11 | ROM2 | 597C |
| J2-12 | ROM1 | UA87 |
| C1-7 | ROMO | 4154 |
| C146 | ROMX | 960F |
- CAT Box Settings for Address Decoder Test
Probe Trigger Testpoint
| Start | L | A6-4 |
| Stop | + | A6-4 |
| Clock | St | 2 |
- Signatures
Verify CAT Box setting and connections as follows: probe +5V = 755U signature.
Logic Probe Signature on IC-Pin Should Be B3-9 970C B3-10 868C B3-11 7FF8 B3-12 1817
D. ROM and Data Lines
- CAT Box Settings for ROMX Test (LC. Di for ROM part no. 136002-101, 113 or 133.)
| Probe | Trigger | Testpoint |
| Start | = | ROMX |
| Stop | a | ROMX |
| Clock | LL | o2 |
- Signatures
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| D1-9 | DBO | 1F4H |
| D1-10 | DB1 | 4P55 |
| D1-11 | DB2 | P2C5 |
| 01-13 | DB3 | UH32 |
| D1-14 | DB4 | 4HFA |
| D1-15, | DBS | op76 |
| D1-16 | DB6 | 86CP |
| D1-17 | DB7 | P29C |
- CAT Box Settings for ROM1 Test (LC. Fi for ROM part no. 136002-103, 115 or +134.)
| Probe | Trigger | Testpoint |
| Start | oni | ROMi |
| Stop | an | ROM1 |
| Clock | =. | o2 |
- Signatures Verify CAT Box settings and connections as follows: probe + 5V=7A70 signature.
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| F1-9 | DBO | 3892 |
| F1-10 | DB1 | 01US |
| F1-11 | DB2 | PH6P |
| F1-13 | DB3 | UPSF |
| F1-14 | DB4 | UP44 |
| F415 | DBS | CA33 |
| F1-16 | DB6 | 3U05 |
| F117 | DB7 | 8CP3 |
- CAT Box Settings for ROMO Test (LC. E1 for ROM part no. 136002-102 or -114. LC. D1 for ROM part no. 136002-133.)
| Probe | Trigger | Testpoint |
| Start | Lk | ROMO |
| Stop | a | ROMO |
| Clock | L | o2 |
- Signatures Verify CAT Box settings and connections as follows: Probe + 5V=7A70 signature.
- CAT Box Seitings for ROM2 Test (LC. H1 for ROM part no. 136002-104 or -116. 1.C. F1 for ROM part no. 136002-134.)
| Probe | Trigger | Testpoint |
| Start | LL | ROM2 |
| Stop | a | ROM2 |
| Clock | ao | o2 |
- Signatures Verify CAT Box settings and connections as follows: probe +5V =7A70 signature.
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| E19 | DBO | 6481 |
| E1-10 | DB1 | P6AQ |
| E1-11 | DB2 | 9552 |
| E1-13 | DB3 | 40F3 |
| E1-14 | DB4 | 37C2 |
| E1-15 | DBS | 0A18 |
| E1-16 | DB6 | A2C0 |
| E1-17 | DB7 | 9HC5 |
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| H1-9 | DBO | 7550 |
| H1-10 | DB1 | AO1F |
| H1-11 | DB2 | A540 |
| H1-13 | DB3 | 5U60 |
| H1-14 | DB4 | 2068 |
| H1-15 | OBS | 9767 |
| H1-16 | OBS | S4CA |
| H1-17 | DB7 | 7F8F |
- CAT Box Settings for ROMS Test (LC. J1 for ROM part no. 136002-105, -117 or 135.)
| Probe | Trigger | Testpoint |
| Stan | L | ROM3 |
| Stop | TI | ROM3, |
| Clock | ML | v2 |
- Signatures Verify CAT Box settings and connections as follows: probe +5V=7A70 signature.
| Logic Probe | Signa! | Signature |
| on IC-Pin | Name | Should Be |
| J1-9 | DBO | O9A6 |
| J1-10 | DB1 | 6A12 |
| J1-11 | DB2 | 91CA |
| J1-13 | DB3 | 10HP |
| J1-14 | DB4 | F53U |
| J1-15 | DB5 | c87C, |
| J1-16 | DB6 | 8272 |
| J1-17 | DB7 | F651 |
- CAT Box Settings for ROM4 Test (LC. K1 for ROM part no. 136002-106 or -118. 1.C. J1 for ROM part no. 136002-135.)
| Probe | Trigger | Testpoint |
| Start | L | ROM4 |
| Stop | ST | ROM4 |
| Clock | a | o2 |
- Signatures Verify CAT Box settings and connections as follows: probe +5V=7A70 signature.
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| K1-9 | DBO | A8FU |
| K1-10 | DB1 | U3U7 |
| K1-11 | DB2 | C8CH |
| K1-13 | DB3 | 353F |
| K1-14 | DB4 | 93FU |
| K1-15 | DBS | UFH1 |
| K1-16 | DBE | A165 |
| K1-17 | DB7 | 5399 |
- CAT Box Settings for ROMS Test (I.C. LIM1 for ROM part no. 136002-107, -119 or -1386.)
| Probe | Trigger | Testpoint |
| Start | L | ROMS |
| Stop | Tr | ROM5 |
| Clock | Lt | 02 |
- Signatures Verify CAT Box settings and connections as follows: probe +5V=7A70 signature.
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| UM1-9 | DBO | 4876 |
| UM1:10 | DB1 | 5397 |
| UM1-11 | DB2 | 7396 |
| UM1-13 | DB3 | CSCH |
| UM1-14 | DB4 | HF73 |
| UM1-15 | DBS | 11U6 |
| UM1-16 | DB6 | 43C8 |
| UM1-17 | DB7 | 2P85 |
- CAT Box Settings for ROM6 Test (I.C. M/N1 for ROM part no, 136002-108 or -120. 1.C. LIM1 for ROM part no. 136002-136.)
| Probe | Trigger | Testpoint |
| Start | on | ROM6 |
| Stop | JS | ROM6 |
| Clock | a | o2 |
- Signatures Verify CAT Box settings and connections as follows: Probe +5V=7A70 signature.
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| MIN-9 | DBO | A4AC |
| MIN-10 | DBI | 3A7C |
| MIN-11 | DB2 | OF 22 |
| MIN-13 | DB3 | H221 |
| MIN-14 | DB4 | 2HO07 |
| MIN-15 | DB5 | 818A |
| MIN-16 | DB6 | 1699 |
| MIN-17 | DB7 | 4149 |
17. CAT Box Settings for ROM7 Test (LC. Pt for ROM part no. 136002-109, -121 or -137.)
| Probe | Trigger | Testpoint |
| Start | au | ROM? |
| Stop | J | ROM7 |
| Clock | TL | 02 |
- Signatures Verify CAT Box settings and connections as foilows: probe +5V=7A70 signature.
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| P19 | OBO | P4F3 |
| P1-10 | DB1 | 2C06 |
| P1-11 | DB2 | 4614 |
| P1113 | DB3 | TA63 |
| P1-14 | DB4 | 434C |
| P1-15 | DBS | 3C66 |
| P1-16 | DBs | P8U6 |
| P1-17 | DB7 | 2C3A |
- CAT Box Settings for ROM8 Test (LC. Rt for ROM part no. 136002-110 or 122. LC. P1 for ROM part no. 136002-137.)
| Probe | Trigger | Testpoint |
| Start | Lk | ROM8 |
| Stop | Tt” | ROM8 |
| Clock | TL | o2 |
- Signatures Verify CAT Box settings and connections as follows: Probe +5V =7A70 signature.
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| R19 | DBO | QHFP |
| R1-10 | 0B1 | U7HH |
| R1-11 | DB2 | F32H |
| R1-13 | DB3 | Fé6U |
| R1-14 | DB4 | U379 |
| R1-15 | DBS | 490P |
| R16 | DBS | 5P99 |
| R1-17 | DB7 | CFA8 |
- CAT Box Settings for Vector ROM Test (i.c. NiP3 for part no. 136002-111, -123 or -138.)
| Probe | Trigger | IC-Pin | Testpoint |
| Start | kh | 1-10 | |
| Stop | at | C110 | |
| Clock | lh | o2 |
- Signatures Verify CAT Box settings and connections as follows: Probe + 5V=7A70 signature.
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| NIP3-9 | DBO | H1U9 |
| N/P3-10 | DB1 | 5U8C |
| NIP3-11 | DB2 | ocsg |
| NIP3-13 | DB3 | 507P |
| NIP3-14 | DB4 | 2A8P |
| NI/P3-15 | DBS | Q9FOC |
| N/P3-16 | pB6 | AH97 |
| N/P3-17 | 0B7 | 29AH |
- CAT Box Settings for Vector ROM1 Test (1.c. 23 for part no. 136002-112 or -124.)
| Probe | Trigger | IC-Pin | Testpoint |
| Start | kL | C1Ping | |
| Stop | a | C1 Ping | |
| Clock | kL | 2 |
- Signatures
| Logic Probe | Signal | Signature |
| on IC-Pin | Name | Should Be |
| R3-9 | DBO | 3FH3 |
| R3-10 | DB1 | OH59 |
| R3-11 | DB2 | 9HSH |
| R3-13 | DB3 | 98PF |
| R3-14 | DB4 | PA27 |
| R3-15, | DB5 | 5U3H |
| R3-16 | DB6 | 97FC |
| R3-17 | 0B7 | 583A |
E. Math Box
The Math Box signature analysis procedure is somewhat different from other procedures, so follow these set-up instructions for the three tests carefully.
In addition to your CAT Box or signature analyzer, you'll need an SA Harness Assembly. Order Atari part number A036836-01 or see Figure 6 to make your own.
A. Math Box Test #1 Procedure:
- Plug SA Harness Assembly Test #1 connector onto Signature Analyzer connector (J16) on the Auxiliary PCB.
- Connect the CAT Box Start, Stop and Clock E-Z hooks to the SA Harness Assembly as shown in Figure 7.
- On the main PCB, connect PWR ON RESET test Point to ground, and power-up the game and the CAT Box.
- Don’t remove the microprocessor (6502A) from the main PCB. Don’t connect the 50 pin ribbon cable to the main PCB edge connector. Don't connect W DOG DIS to ground.
- Set the CAT Box switches as follows: a. START _J— b. STOP _J_ ce. CLOCK_I— d. TESTER MODE: SIG e. Press TESTER RESET
- With the logic probe touching the + 5V test point on the Auxiliary PCB, the ADDRESS/SIGNATURE display should read CC34. This will verify that your test set-up is correct. If you don’t get CC34, recheck your set-up.
Figure 6 S.A. Harness Assembly
S.A. Harness Assembly 12-CIRCUIT HOUSING MOLEX P.N. 09-50-7121
TERMINAL MOLEX P.N. 08-50-0106
a QUANTITY = 18
#1 CC34 #23951 #3 3951
abl
Signatures Logic Probe on IC-Pin C1-11 01-12 C1-13 C1-14 01-11 01-12 D1-13 01-14
F1-12 F111 F1-10 F19 H1-12 H1-11 H1-10 H1.9 J1-12 J1-17 J1-10 J1-9
K1-12 Kt K1-10 K19
L1-12 L1-11 L1-10 11-9
E1-12 E1-11 E1-10 E1-9
F4.2 E46 A2-6 B1-2
B15 B16 B1-9 B1-12
B1-15 B1-16 B1-19 K/L2-33,
KIL2-16 K/L2-8 FIH2-33 FIH2-16 Signature Should Be H58A 77F7 85PA 7P25 SCPO P5PH 725C 96PF
4PPF OUFO 3CAP AGA3 26A6 Q1HA P9C1 2987
96U0 Uc59 6989 3FU4 O5A6 60H6 PPF6 3402
58A1 1AA2 F74F 6CF6
F765 CPU8 0000 F515
CC34 AGBA3 0000 8A7H
Ccu2P 1C6C 6U30 5AAH
03A7 9A08 2327 6PUP
9AFH* 809A* 9CPP 1105* FIH2-8 78AA* J2-33 8631 J2-16 1105" J2-8 7U19" E2.34 A1F7 £231 1781 E216 QAFH* 5-11 C646 D4-8 0600 6411 CC34 F5-11 C835" D46 c4au4 F56 753F E48 cpus E58 45A1"
B. Math Box Test #2A Procedure
. Plug SA Harness Assembly Test #2 connector onto Signature Analyzer connector (J16) on the Auxiliary PCB.
- Connect the CAT Box Start, Stop and Clock E-Z hooks to the SA Harness Assembly as shown in Figure 7.
- Don’t remove the microprocessor (6502A) from the main PCB. Don’t connect the 50 pin ribbon cable to the main PCB edge connector. Don't connect W DOG DIS to ground. Don't connect PWR ON RESET to ground.
- Set the CAT Box switches as follows: a. START _T~ b. STOP 7 c, CLOCK “LL d. TESTER MODE: SIG e. Press TESTER RESET
- Enter the self-test mode and advance the screen with the slam switch until the large blank rectangle appears. This procedure is described in Figure 6, Chapter 2 of the Tempest™ Operation, Maintenance, and Service Manual.
- With the logic probe touching the + 5V test point on the Auxiliary PCB, the ADDRESS/SIGNATURE display should read 3957. This will verify that your test set-up is correct. If you don’t get 3951, recheck your set-up.
GND
Signatures CLOCK
Logic Probe Signature T on IC-Pin Should Be STAR
Ad F722 STOP A113 C4P5 A1-12 6UAC A1-11 3441 A1-10 2P61 A1-9 92F3 A17 A856 A16 3050 A1-5 H8F9 Al-4 9569 A1-3 3U53 At-2 OF47 Al-1 4FUF
looOO0000 0000
Figure 7 S.A. Harness Assembly
C. Math Box Test #2B Procedure
- Plug SA Harness Assembly Test #2 connector onto Signature Analyzer connector (J16) on the Auxiliary PCB.
- Connect the CAT Box Start, Stop and Clock E-Z hooks to the SA Harness Assembly as shown in Figure 7.
- Don’t remove the microprocessor (6502A) from the main PCB. Don't connect the 50 pin ribbon cable to the main PCB edge connector. Don’t connect W DOG DIS to ground. Don't connect PWR ON RESET to ground.
- Set the CAT Box switches as follows: a. START _[~ b. STOP “Le c. CLOCK _J~ d. TESTER MODE: SIG e. Press TESTER RESET
- Enter the self-test mode and advance the screen with the slam switch until the large blank rectangle appears. This procedure is described in Figure 6, Chapter 2 of the Tempest™ Operation, Maintenance, and Service Manual.
- With the logic probe touching the + 5V test point on the Auxiliary PCB, the ADDRESS/SIGNATURE display should read 3957. This will verify that your test set-up is correct. If you don’t get 3957, recheck your set-up.
Signatures
Logic Probe Signature on IC-Pin Should Be C1-11 92F3 C1-12 A856 C1-13 3050 C1-14 H8F9 01-11 9569 D1-12 3U53 D1-13 QF47 1-14 4FUF D. Math Box Test #3 Procedure 1, Plug SA Harness Assembly Test #3 connector onto Signature Analyzer connector (J16) on the Auxiliary PCB.
- Connect the CAT Box Start, Stop and Clock E-Z hooks to the SA Harness Assembly as shown in Figure 7.
- Don’t remove the microprocessor {6502A) from the main PCB. Don’t connect the 50 pin ribbon cable to the main PCB edge connector. Don't connect W DOG DIS to ground. Don’t connect PWR ON RESET to ground.
- Set the CAT Box switches as follows: a. START _J b. STOP “L ce. CLOCK _|~ d. TESTER MODE: SIG e. Press TESTER RESET
- Enter the self-test mode and advance the screen with the slam switch until the large blank rectangle appears. This procedure is described in Figure 6, Chapter 2 of the Tempest™ Operation, Maintenance, and Service Manual.
- With the logic probe touching the + 5V test point on the Auxiliary PCB, the ADDRESS/SIGNATURE display should read 3957. This will verify that your test set-up is correct. If you don’t get 3957, recheck your set-up.
Signatures
Logic Probe Signature on IC-Pin Should Be E2-22 1441 E2.23 2883 E2-24 5107 E2-25 A20P J2-22 441H J2-23 883A J2-24 1074 J2-25 20P9
NOTES:
NOTES:
NOTES:
NOTES:
YOUR COMMENTS, PLEASE! Teneesinetch
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm O Distributor
Address 0 Operator
City _. State __ Zip (J Other. -
Area Code Phone
First told
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA
POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086
Second fold No Postage Necessary if mailed in the United States
eBpe syyi ede,
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ATARI INC. 1265 BORREGAS AVENUE P.O. BOX 427 ®
ATARI SUNNYVALE, CALIFORNIA 94086 ee
408/745-2000 ¢ TELEX 35-7488 iti