CATHODE RAY TOMES

Lost World DLX

The Lost World: Jurassic Park (pinball, CPU 2.02, display A2.01) (Sega, 1997) · Manual · 89 pages · 71 sections · original scan

Page 1

SEGA ENTERPRISES, USA

MANUAL NO. 4201-6325-02

Page 2

Warranty

Your new SEGA product is covered for a period of 90 Days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in thew event a warranted part described above fails shall be, at it’s option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your SEGA distributer.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 3

INTRODUCTION

GENERAL PRECAUTIONS

  • NAME OF PARTS.
  • ACCESSORIES
  • ASSEMBLING AND PRECATUIONS
  • PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE
  • CONTENTS OF GAME
  • EXPLANATIN OF TEST AND DATA DISPLAY

6-1 SWITCH UNIT AND COIN METER

6-2 TEST MODE

6-3 MEMORY TEST

6-4 INPUT TEST

6-5 SOUND TEST

6-6 C.R..T. TEST

6-7 OUTPUT TEST

6-8 GAME ASSIGNMENTS

6-9 COIN ASSIGNMENTS

6-10 GUN SETTING

6-11 BOOKKEEPING

6-12 BACK UP DATA CLEAR

  • CONTROLLER

7-1 REPLACING THE MICROSWITCH

7-2 REPLACING THE SENSOR BOARD

  • COIN SELECTOR
  • PROJECTOR

9-1 CLEANING THE SCREEN,

9-2 MITSUBISHI PROJECTOR

  • REPLACEMENT OF THE FLUORESCENT LAMP AND LAMPS

10-1 FLUORESCENT LAMP REPLACEMENT

10-2 BUTTON LAMP REPLACEMENT

  • PERIODIC INSPECTION TABLE
  • TROUBLE SHOOTING

12-1 REPLACING THE LED BOARD

  • GAME BOARD

13-1 REMOVING THE GAME BOARD

13-2 COMPOSITION OF THE GAME BOARD

  • DESIGN RELATED PARTS
  • PARTS LIST
  • WIRING DIAGRAM 2-3

a11

13~21

22-34

28~31

32233

35~36

37~38

39~42

40~42

43~44

46~47

48~49

51-81

XXX

Page 4

SPECIFICATIONS

Installation space: 104 in.(L) x 50 in.(W)

Height: 85 in.

Weight: Approx. 975 lbs.

Power maximum current: 5 Amp AC 120V 60 Hz AREA

MONITOR: 50 INCH PROJECTION DISPLAY

INTRODUCTION OF THE OWNERS MANUAL

SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and popular amusement products to the world market. This Owners Manual is intended to provide detailed descriptions together with all the necessary installation, game settings and parts ordering information related to the LOST WORLD DLX, a new SEGA product.

This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system. Should the need arise, contact our main office, or the closest branch office listed below.

SEGA ENTERPRISES, INC. (USA) Customer Service 45133 Industrial Drive Fremont, CA 94538 Phone 415-802-1750 Fax 415-802-1754 7:30 am - 4:00 pm, Pacific Standard Time Monday thru Friday

Page 5

General Precautions

Follow Instructions: All operating and use instructions should be followed. Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards. Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use only mounting accessories recommended by the manufacturer. Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product to overturn. Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Power Sources: This product should be operated only from the type of power source indicated on the marking label. Tf you are not sure of the type of power supply to your location, consult your local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring Service: Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

  • If the power cord or plug is damaged;
  • If liquid has been spilled, or objects have fallen into the product;
  • If the product has been exposed to rain or water;
  • If the product does not operate normally when following the operating instructions. Adjust only those controls that are explained in the operating instructions. An improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation;
  • If the product has been dropped or damaged in any way;
  • When the product exhibits a distinct change in performance; this indicates a need for service. Replacement Parts: When replacement parts are required, be sure the service technician has used replacements parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Page 6

Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’s recommendations. Do not dispose in an open flame condition, since the battery may explode. Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such as benzine, thinner, etc. Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid installing indoors in the places mentioned below:

  • Places subject to rain/water leakage, or condensation due to humidity; In close proximity to a potential wet area;
  • Locations receiving direct sunlight;
  • Places close to heating units or hot air; eIn the vicinity of highly inflammable/volatile chemicals or hazardous matter;
  • On sloped surfaces; + In the vicinity of emergency response facilities such as fire exits and fire extinguishers;
  • Places subject to any type of violent impact;
  • Dusty places.

INSTALLATION PRECAUTIONS

  • Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit.
  • Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/3 AWG rated min. 120 VAC, 7A.
  • Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H). ¢ For the operation of this machine, secure a minimum area of 32” (W) by 42”(D).

REGULATORY APPROVALS This game has been tested and found to comply with the Federal Communications Commission Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.

LISTED

5K92

AMUSEMENT MACHINE

Page 7
  • NAME OF PARTS

FRONT PTV “CABINET

REAR

AC UNIT

COIN CHUTE DOOR

CASHBOX DOOR __/

CONTROLLER (GUN)

FIG.1 OVERVIEW

GAME SPECIFICATIONSWIDTHHEIGHTDEPTHWEIGHT
FRONT CABINETsis”XX)73S"X37”440 LBS.
PTV w/PTV BASE46.5”x67”= X75”250 LBS.
REAR CABINET5175"X75”xX55.5”385 LBS.
MARQUEE4”xX24"x”50 LBS.

DURING SHIPPING 1,125 LBS.

FRONT CABINET50”xRBX35.5”400 LBS.
PTV w/PTV BASE45”x66"OX24”225 LBS.
REAR CABINET50”x705"X50”350 LBS.
MARQUEE46”x20.5"X8”40 LBS.
WHEN ASSEMBLED50”x90”x104”1015 LBS.
Page 8
  • ACCESSORIES

KEY MASTER KEY DESCRIPTION OWNERS MANUAL 220-5576 (2) (2) Part No. (Qty.) 420-6325-02 (1) For opening/closing the doors.

Note For the CASHBOX DOOR

FIGURES

If Part No.has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it. Therefore, ensure that the part is in safekeeping with you.

SW MICRO TYPE (TAMPERPROOF WRENCH) 509-5080 (1) M4 540-0006-01 (1)

For spare refer to section 10 TOOL

T-25 TORX M-3 TORX T-15 TORX

MITSUBISHI 50” PROJECTOR MONITOR REMOTE CONTROL 200-5532 (1)

Used for adjustment

Page 9

Board (MODEL 3 BOARD), be sure to put the Game Board together with the shield case in the Carton Box.

IMPORTANT! @ Put the Shield Case in the Carton Box by paying attention to the

correct direction as per the following instructions and as shown by the instructions printed on the Carton Baox. Handling in an erroneous manner can damage the Game Board.

S @ When Asking for the replacement or repair of the product’s Game

CARTON BOX 601-8928 (1)

Used for transporting the GAME BOARD Ay

“CHECK SIDE” Display

FILTER BOARD

Wrap the Shield Case with the packing material and put in the Carton Box as shown. Putting it upside down or packing otherwise in the manner not shown can damage the Game Board and parts.

Page 10
  • ASSEMBLING PRECAUTIONS
WARNING! Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling may cause damage to the machine, or malfunctioning to occur. When assembling, be sure to perform work by plural persons. Depending on the assembly work, there are some cases in which performing the work by a single person can cause personal injury or parts damage.

When carrying out the assembly work, follow the procedure in the following 4-item sequence:

Note that t 1 | ASSY OF CABINETS AND BILLBOARD INSTALLATION

2 | SECURING IN PLACE (ADJUSTER ADJUSTMENT)

3 | POWER SUPPLY

4 | ASSEMBLING CHECK

tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width across flats are required for the assembly work.

A

CAUTION!

A

WARNING! ASSY OF CABINETS AND INSTALLATION OF BILLBOARD

It is difficult to carry out work by one person. Be sure to perform work by plural persons.

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Not using a step or using an unstable step can cause a violent falling down accident.

Page 11

work with each cabinet’s casters as is in contact with the floor. Working with the adjusters in contact with the floor can damage

CAUTION! parts and floor surfaces, also working in this status is difficult

f During assembling work, cabinets are moved. Be sure to perform

@ Install the Connect Lid and PTV Bracket to the PTV.

SCREWS(2)

8x8 SMS TMPR PRF oN

  • WSHR LOCK #10 3 &

CONNECT LID

SCREW (4) M5x25 PH PN

  • WHSR SPLIT LOCK.

PTV BRACKET ad

Page 12

@ Jointing the PTV, FRONT CABI, and REAR CABI. Insert the wiring connectors, each of which wire covering is red, green, and blue, to the corresponding one of R.G.B. terminals as per connector panel display inside the PTV, and insert the remaining wire connector to the SYNC terminal. The connector’s insertion angle is predetermined. Inserting the connector in a forcible manner will damage the connector. Check for the correct inserting direction and then insert the connector. After the insertion of the connector, turn the connector’s ring clockwise to lock the connection.

HEXAGON BOLT (1/4-20x16) (4) [= 1 (4) LOCK 1°4” wshr (4) 1/4”

FRONT CABI

HEXAGON BOLT (M8x60) (4) {wshr (4) FL 5/16" wshr (4) LOCK 5/16”

Page 13

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Using an unstable step can cause

CAUTION! | a violent falling down accident.

2 Install the Billboard Plate to the Billboard Box and adhere the POP Panel with 2-sided adhesive tape.

POP PANEL

BILLBOARD PLATE FLANGE NUT (2) 2-SIDED ADHESIVE TAPE

(Z Install the assembled Billboard to the Rear Cabinet. After connecting the Connector, secure with 2 screws.

Prepare a step to Be sure to perform perform work. work by plural persons.

Page 14

2 SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Be sure to have all the Adjusters make contact with the floor surface. Unless the Adjusters come into contact with the surface, the Cabinet can move of itself, causing an accident.

This machine has 12 each of casters and adjusters (FIG. 3. 2 a). When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately Smm. from the floor and make sure that the machine position is level. . ADJUSTER (12 in total)

[-) Move the machine to the installation a & eis & B position.

Q) Cause all of the leg adjusters to make

contact with the floor. By using a wrench, make adjustments in the height of the leg adjusters to ensure that the S we rE machine's position is level. CASTER (12 in total)

@ After making adjustments, fasten the

leg adjuster nut upward and secure the FIG. 3. 2a BOTTOM VIEW height of the leg adjuster.

CASTER

FASTEN UPWARDS

1/4” INCH

LEG ADJUSTER FIG. 3. 2b ADJUSTER

Page 15

3 | power SUPPLY

@ Ensure that the power cord is not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord can cause an electric shock or short circuit. Ensure that the wiring position is not in the customer's passage way

WARNING! or the wiring has protective covering.

The AC unit is mounted on the left side of Front Cabinet DX. The AC Unit incorporates the Main SW. Firmly insert the Power Plug into the Socket Outlet. Turn the Main SW ON to turn power ON.

(Ensure that the Main SW is OFF. FIG.3.1 AC Unit

Line cord & oO; 1 J Main SW

REPLACEMENT AND ADJUSTMENT OF FUSE

performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electrical shock or short circuit accident. @ Be sure to use fuses meeting specified rating. Using fuses exceeding the specified rating can cause a fire or electrical shock. @ After eliminating the cause of the fuse blowing, replace the fuse. Depending on the cause of fuse blowing, continued use with the fuse as is blown can cause generation of heat resulting in a fire.

A @ !n order to prevent electrical shock, be sure to turn power off before

WARNING!

Unplug the unit.

Remove the AC Switch Panel on the left side of the game which secures the PTV and Front Cabinet Dx.

The 4 fuses are now visible. Replace the blown fuse. Always replace the fuses with the same type and current rating for continued protection.

By using the reverse procedure reinstall the AC Switch Panel. © © ©O

Page 16

ASSEMBLING CHECK

In the TEST MODE, ensure that the assembly has been made correctly and IC BD is satisfactory (refer to Section 6). In the test mode, perform the following test:

Selecting the MEMORY TEST on the test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD. MEMORY TEST

PRESS TEST BUTTON TO EXIT

Selecting the INPUT TEST on the test mode menu screen causes the screen (on which each INPUT TEST PLAYER] PLAYER2 . : : ‘TRIGGER off oft switch is tested) to be displayed. Press each START ff off . mg 4G wat COIN CHUTE! or switch. For the coin switch test, insert a coin

Seance or into the coin inlet with the coin chute door

being open. If the display beside each switch indicates "ON," the switch and wiring connections are satisfactory.

PRESS TEST BUTTON TO EXIT

SOUND TEST

VOICE

, BoM In the TEST mode, selecting SOUND TEST

causes the screen, on which sound related BD and wiring connections are tested, to be displayed. be sure to check if the sound is satisfactorily emitted from each of speaker and the sound volume is appropriate.

‘SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Page 17

C.R.T. TEST 1/2

PRESS TEST BUTTON TO CONTINUE

sightXpos sight¥pos. ssreenXpos screenYpos.

{OUT OF SPREEN 1P)

CURSOR. (Impact Position)

QUTPUT TEST

PLAYER | PLAYER 2 ROOM LIGHT > MARS LIGHT exit

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the monitor is tested) to be displayed. Although the monitor adjustments have been made at the same time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnitism, the location building’s steel frames and other game machines in the periphery. By watching the test mode screen, make judgement as to whether an adjustment is needed. If it is neccessary, adjust the monitor by refering to Section 9.

On the menu screen in the test mode, selecting GUN SETTING displays the screen on which gun setting is set. Check to see if there is any problem for playing game.

IMPACT MARK

Select "OUTPUT TEST" from the Test Menu in the Test Mode to have the Lamp Test Screen displayed. Check if each lamp lights up satisfactorily.

Page 18
  • PRECATIONS TO BE HEEDED WHEN MOVING THE MACHINE

@ When moving the machine, be sure to pull out the plug from the power supply. Moving the machine with the plug as is

WARNING! inserted can damage the power cord and cause a fire or electric shock. @ When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords. Damaging the power cords can cause an electric shock and/or short circuit. @ When lifting the cabinet, be sure to hold the catch portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions, due to the empty weight of the cabinet, and cause personal injury.

Use care when handling glass made parts. When the glass is damaged, fragments of glass can cause injury

CAUTION!

Do not push the PTV from the rear side. Pushing the PTV from the rear side can cause the PTV to fall down. Push it from the side Do not push from this position

Where there are steps (or step like differences in grade), move the machine by seperating into each unit.

Page 19
  • CONTENTS OF GAME

@ Inserting a coin(s) causes the credit display on the bottom of the screen to count. Inserting one credit worth coin(s) changes the message on the bottom of the screen from "INSERT COIN(S)" to "PRESS START BUTTON" and both of the start buttons will flash.

Q) Pressing either of the start buttons determines which side (left or right) you are playing on. Press the START button to start the game.

B) After starting the game, the Title of the Stage being started and the purpose of game are displayed.

SIGHT.

The Cartridge picture shows charged bullets

gun runs out of ammo, RELOAD is displayed

When your gun runs out of ammo, point outside the screen and pull trigger to reload.

@ The life points and the number of bullets of the lefthand side player (1P) are displayed on the lower lefthand side of the screen, and those of the right-hand side player (2P), on the lower right-hand side of the screen.

@ Lose one life when a dinosaur attacks you.

@ The player loses one life point if he shoots a human by mistake.

Page 20

@ The gun holds 5 bullets. When it runs out of ammo, "RELOAD" is displayed on the screen. At this time, g play point outside the screen and pull the trigger to reload.

@ when the life point reaches zero the game is over.

e Downing the boss character awaiting you at the end of each stage results in clearing that particular stage. The player can not defeat the boss until the life meter of the boss becomes zero.

@ Sometimes shooting the background scenery can cause Special Items to appear. The Special Items can be captured by shooting. Capturing an item allows you to earn points or recovers life points (explanations as regards to the Items are given later).

Downing the Boss character awaiting you at the end of each stage results in clearing that particular stage. The player can not defeat the boss until the life meter of the boss becomes zero.

@ The sight mark sometimes appears on the enemy. At this time, unless the enemy is downed before the sight turns red, the player’s life point may be lost or the player’s status could become extremly unfavorable.

Unless the enemy is downed before the sight turns red, the player’s status could be extremly unfavorable.

Page 21

@ When fighting against the boss character at the end of each stage in the 2 player simultaneous play, if all of the sights cannot be shot, the screen will be in objective mode and in this case either of the players may be taken away by the enemy.

. The player who is taken away will remain on the screen as is between the dinosaur’s teeth. Herein, he is refered to as player A. . The other player who is not taken away stays on the screen in the subjective mode. Herein, he is refered to as player B.

Player A who is taken away.

SIGHT

. At this time, Player B who is not taken away can resue Player A by shooting all of the sights before the sight attached to the boss turns red. ° Although Player A can not shoot with the gun, he can extend the completion time of the sight attached to the boss by repeatedly pressing the Start Button. . If Player B fails to shoot all of the sights before the boss sight becomes red, then Player A will be subject to damage and Player A loses one life.

Page 22

® If you would like to join in the game at anytime while the other is playing, insert a coin(s) and press the start button. Also, when credits allowing the game to be played still remain, the start button on the other side will keep flashing. The player can participate in the game by pressing the flashing button.

When the life point becomes zero, if you want to continue, insert a coin(s) required to continue and press the start button. If the credits allowing the player to continue still remain, you can continue by merely pressing the start button.

At the time of Game Over, if the player’s score ranks 10th or higher, his name can be entered.

NACK OF PLAY

TO SHOOT AND DESTROY OBJECTS THAT EMIT SOUND: In any stage, the enemy characters other than the boss character will face in the direction where sound is emitted in response to sound and during this time, they stop attacking temporarily. When you are surrounded by plural enemies, shoot anything that emits sound to divert the enemy’s attention. Things that emit sound are glass, metal, wooden items, etc.

QUICK SHOT

Shooting the sound emitting items (glass, metals, etc.) causes the dinosaur to respond to the sound produced and the alarm sound emitted by the fellow dinosaur whose head is shot, and thus the enemy temporarily stops attacking.

ACCURATELY SHOOT THE HEAD: In each stage, the head part is the weak point of the enemy characters other than the boss. Shooting the head produces a very loud alarm sound which results in the same effect as shooting objects that emit sound.

SUCCESSFULLY PERFORM AN EVENT: Successfully achieving an event which takes place during a stage allows you to favorably proceed with what’s coming thereafter. On the other hand, failing to acheive the event causes the enemy attack to become more furious and the situation for the player to be less favorable. Continuously hitting the target enemy without missing earns you high points.

Page 23

REGARDING THE ITEMS

S-POWERBAR (SPECIAL POWER BAR) This increases your “LIFE” by one.

POWERBAR Collecting 3 POWERBARs increases your “LIFE” by one.

GERNADE Hitting this against the earth surface damages the target(s) over a wide area. During the limited time, there is no limit regarding the number of gernades that can be used. When the limited time elapses, this returns to an ordinary gun..

SHOTGUN Having a wide scope for hit determination, this damages the target(s) in an extensive area. During the limited time, there is no limit regarding the number of bullets that can be used. When the limited time elapses, this returns to an ordinary gun.

LIGHTNING Hitting a target damages targets within a certain scope from that particular point. During the limited time, there is no limit regarding the number of bullets that can be used. When the limited time elpases, this returns to an ordinary gun.

LASER-SITE The present place at which the gunpoint appears on the screen in real time is the pointer. During the limited time, there is no limit regarding the number of bullets that can be used. When the limited time elapses, this returns to an ordinary gun.

Page 24

DINOSAURS apeearing in The Lost World: Jurassic Park- The Arcade Game

VELOCIRAPTOR

Alias: RAPTOR Weight: 45 kg. Length: 2m Flesh-Eater One of the most ferocious dinosaurs in The Lost World. Captures prey by taking an advantage of sharp, long & hook-shaped claws and agile movements as powerful weapons. This dinosaur seems to have brains and skills to pursue prey in groups.

APPEARENCE IN ALL STAGES

MAMENCHISAURUS

Weight: 12 tons. Length: 22m _ Plant-Eater MAMENCHISAURUS was a living creature with an approximately 11m long head & neck portion, about half of the total length, the longest ever ( in relation to the physical length) in the terrestrial history. Since the head movements were not so versatile, it might have been able to stand on it’s rear feet alone sometimes to make up for the handicap.

APPEARENCE IN STAGE 2

TRICERATOPS

Weight: 6 tons. Length: 9m _ Plant-Eater This plant-eater has features of three large horns and an accessory-like pattern around the neck portion which derive its name . It’s a gentle dinosaur which eats young buds, etc. with the edge-sharp beak.

APPEARENCE IN STAGE 1

TYRANNOSAURUS-REX

Alias: T-REX Weight: 6.5 tons. Length: 12m _ Flesh-Eater This flesh eating dinosaur is well-known and the strongest one ever in history. Although physically gigantic, it seems that this dinosaur was unable to run fairly quickly to pursue prey. The sharp biting attack ability with teeth of 17 cm. length could be the maximum threat.

APPEARENCE IN STAGE | & ?

Page 25

GALLIMIMUS

Weight: 130 kg. Length: 4m Omnivorous This dinosaur running in groups in the “JURASSIC PARK” Movie is very impressive. It has the skeletal structure quite similar to an ostrich and it’s movements are the fastest of all dinosaurs. Having omnivorous-eating habits, it eats insects, small lizards, and fruit.

APPEARENCE IN STAGE 2

STEGOSAURUS

Weight: 1.5 tons. Length: 6m _ Plant-Eater A large body and small head as well as the spine are very characteristic. It seems that the 2 pairs of tail spines are utilized for defense, and also, they always act in groups.

APPEARENCE IN STAGE 1

DILOPHOSAURUS

Alias: SPITTER Weight: 1 tons. Length: 6m Flesh-Eater This dinosaur suddenly became infamous as poison spitter in “JURASSIC PARK” the Movie. It is distinguished by the large muffler that spreads out to threaten others.

APPEARENCE IN STAGE 1

PACH YCEPHALOSAURUS

Alias: PACHY Weight: ? Length: 4.5m Plant-Eater Having the head of a dome-shaped skeletal structure, this dinosaur looks strange as if it had a helmet on. The “helmet” portion is as thick as 25 cm. and surrounded by spike-shaped spines. Did it ferociously fight against enemies and its rivals sometimes with head butt attacks by taking advantage of the rock head?

APPEARENCE IN STAGE 2

Page 26

PARASAUROLOPHUS

Weight: ? Length: 10m Plant-Eater The length of the cristated, cylindrical portion of the head is approximately one meter. The cristate is considered to produce cry resonance and to be useful for communicating with fellow dinosaurs belonging to their groups and also instrumental in making amorous approaches.

APPEARENCE IN STAGE 2

ANATOSAURUS

Weight: 3 tons. Length: 10m Plant-Eater This belongs top one of the duck-billed dinosaur species, the same as PARASAUROLOPHUS. Its characteristic is the duck-billed wide beak. A number of back teeth allows it to eat hard things such as pine needles and nuts.

APPEARENCE IN STAGE 2

PROCOMPSOGNATHUS

Alias: COMPY Weight: 3kg. Length: 60cm Flesh-Eater This is one of the smallest dinosaurs, only as large as a chicken. It can move quickly and catches small animals such as lizards, etc., and sometimes attacks human adults with large groups.

APPEARENCE IN STAGE 1,3, and 5

DEINOSUCHUS

Weight: ? Length: 15m Flesh-Eater The name is derived from “fearful alligator”. Although belonging to a species different from the dinosaur, this is a ferocious flesh-eater which attacks living creatures and fish at the waterside. The length is said to be 15m though the appearence is almost the same as currently existing alligators. Its weapons are the jaws lined up with sharp teeth and a strong tail.

APPEARENCE IN STAGE 2

Page 27

PTERANODON

Weight: 17 kg. Length: 7m (when wings are opened) Flesh-Eater PTERANODON signifies that it has wings and is toothless. It used to glide through the air like a glider with its wings spread out. Freely flying through the sky, it pursues prey from above with its sharp beak.

APPEARENCE IN STAGE 4

CARNOTAURUS

Weight: ? Length: 12m Flesh-Eater The characteristics are a two short strange looking spines on top of it’s head. In the LOST WORLD the original novel, this is given a designation of chameleon dinosaur, and captures prey by surprising those that come to near. Capable of changing its color to match its surroundings.

APPEARENCE IN STAGE 4

Page 28
  • EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

TABLE6 EXPLANATION OF TEST MODE

ITEMS DESCRIPTION SECTIONS

When the machine is installed, perform the following: INSTALLATION | |. Check to see that each setting is as per standard setting made 6-8, 6-9, OF MACHINE at the time of shipment. 6-10

2.In the INPUT TEST mode, check each SW and VR. 6-4

3.In the OUTPUT TEST mode, check each of lamps. 6-7

  • In the MEMORY TEST mode, check ICs on the IC Board. 6-3
MEMORYChoose MEMORY TEST in the MENU mode to allow the6-3

MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked.

PERIODIC Periodically perform the following: SERVICING

  • MEMORY TEST 6-3
  • Ascertain each setting. 6-8,6 -9

3.In the INPUT TEST mode, test the CONTROL device 6-4

  • In the OUTPUT TEST mode, check each of the lamps. 6-7
CONTROL1. In the INPUT TEST mode, check each SW and VR.6-4

SYSTEM

  • Adjust or replace each SW and VR. 7

3.If the problem hasn’t been solved yet, check the CONTROL’s moves 7

PROJECTOR In the PROJECTOR ADJUSTMENT mode, check to see if the PROJECTOR adjustment is appropriately made. 6-7

IC BOARD1. MEMORY TEST6-3
  • In the SOUND TEST mode, check the sound related ROMs. 6-5
DATA CHECKCheck such data as game play time and histogram to adjust the6-11

difficulty level, etc

Page 29

6 - 1 SWITCH UNIT AND COIN METER

Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit.

@ Adjust to the optimum sound volume by considering the environmental requirements of the installation location. @ If the COIN METER and the game board are electrically disconnected,

IMPORTANT! game play is not possible.

Open COIN CHUTE DOOR, and the switch unit shown appears. The function of each switch is as follows:

@)_ SOUND VOLUME Controls the speaker volume.

@ TEST BUTTON (TEST SW)

For the handling of the TEST BUTTON, refer to the section on test mode.

@ SERVICE BUTTON (SERVICE SW)

Gives credits without registering on the coin meter.

Cover

COIN METER]

Test Service {e) o 8° ©

SHAKER FIG. 6.1

O ©) Volume Front Volume Rear

Page 30

6-2 TEST MODE

Gran In case settings are changed in GAME ASSIGNMENTS, COIN ASSIGNMENTS, and GUN

MPORTANT! SETTING, the setting changes are not effective unless the test mode is exited and the game mode returns to the screen. The setting changes are ineffective if the power is turned off in the test mode.

This mainly checks if the operation of the Game BD is accurate, and allows for COIN ASSIGNMENTS/GAME ASSIGNMENTS setting and Projector adjustments.

SELECTION OF TEST ITEMS

‘TEST MENU

MEMORY TEST INPUT TEST SOUND TEST CAT, TEST GAME ASSIGNMENTS COIN ASSIGNMENTS. GUN SETTING OUTPUT TEST BOOKKEEPING BACKUP DATA CLEAR > EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

6-3 MEMORY TEST

MEMORY TEST

PRESS TEST BUTTON TO EXIT Push the TEST BUTTON to cause the following TEST MENU to appear:

By pushing the SERVICE BUTTON, bring the arrow mark to the desired item and press the TEST BUTTON.

After the test is complete, move the arrow mark to “EXIT” and press the TEST BUTTON to return to game mode.

The MEMORY TEST mode is for checking the on-BD memory IC functioning. “GOOD?” is displayed for normal ICs and “BAD” is displayed for abnormal ICs

@ When the test is completed, if the display is as shown left, it is satisfactory.

@ After finishing the test, pressing the TEST BUTTON allows the MENU MODE to return on the

screen.

Page 31

6-4 INPUT TEST

When INPUT TEST is selected, the MONITOR will show the following, allowing you to watch the status of each switch. On the screen, periodically check the status of each switch.

@ By pressing each switch, if the display on the righthand side of the name of each switch changes to ON from OFF, the SW and the wiring connections are satisfactory.

@ Open the COIN CHUTE DOOR and insert a coin from the COIN ENRTY to check the COIN CHUTE SW.

In the INPUT test, pressing the TEST BUTTON causes the menu to return to the screen. PRESS TEST BUTTON TO EXIT

6-5 SOUND TEST

SOUND TEST

This enables sound used in the game to be checked. Sound related memory and each speaker are checked. Press the SERVICE BUTTON to bring the arrow to the desired sound item to be tested. Pressing the TEST BUTTON causes the desired sound test to

appear. Each time the SERVICE BUTTON is pressed, SELECT WITH SERVICE BUTTON. : ‘AND PRESS TEST BUTTON the numeral displayed on the screen counts up and sound is emitted.

Page 32

6-6 C.R.T. TEST

OAT. TESTIVe

PRESS TEST BUTTON TO CONTINUE,

C.R.T. TEST 2/2

PRESS TEST BUTTON TO EXIT

6-7 OUTPUT TEST

OUTPUT TEST

PLAYER | PLAYER 2 ROOM LIGHT > MARS LIGHT

BXIT

‘SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON Select C.R.T. TEST to cause the MONITOR to display the screen shown left, allowing MONI- TOR adjustment status to be checked.

Periodically check the MONITOR adjustment status on this screen.

The screen (1/2) enables color adjustment check to be performed. The color bar of each of the 4 colors, i.e.,red, green, blue, and white, is the darkest at the extreme left and becomes brighter towards the extreme right.

Press the TEST BUTTON to shift to the next page (2/2).

The screen (2/2) allows screen size and distortion to be tested.

Check if the CROSSHATCH FRAME LINE goes out of the screen and if the crosshatch lines are distorted.

Press the TEST BUTTON to return to the MENU mode. (FIG. 6.2)

Choose OUTPUT TEST to have the MONI- TOR screen shown left to appear. This screen allows lamp status to be checked.Periodically check the lamp status in this mode.

Press the SERVICE BUTTON to move the arrow to the desired lamp test item.

Press the TEST BUTTON. If the display to the right of the lamp name changes to ON from OFF, the lamp and wiring connection are satisfactory.

Choose EXIT and press the TEST BUTTON to return to MENU mode (FIG. 6.2).

Page 33

6-8 GAME ASSIGNMENTS

Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings to be displayed and also the game settings changes (game difficulty, etc.) can be made. Each item displays the following content.

SETTING CHANGE PROCEDURE

Gror) Setting changes cannot be stored unless the TEST BUTTON is pressed

MPORTANT! while the arrow is on EXIT.

@ Press the SERVICE BUTTON to move the arrow to the desired item.

  • Choose the desired setting change item by using the TEST BUTTON.

QB) To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

(— GAME ASSIGNMENTS \ easy bard GAME DIFFICULTY Toon ADVERTISESOUND ON LIFE 3 couNTRY Usa BOSS ACTION NORMAL

>EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

These FIGURES/TABLES show the factory recommended settings.(6-8, 6-9) @ GAME DIFFICULTY Game difficulty can be set in 5 different levels from VERY EASY to VERY HARD

LIFE SETTING The combination set of INITIAL LIFE (the number of life points allotted to the player at the time of game start) and MAX LIFE (the limited number of life points) can be selected from the following 12 variations.

INITIAL LIFE: 123123412345 MAX LIFE: 333444455555

BOSS ACTION The setting of the Boss Character is performed. NORMAL enables Life Recovery, MILD disables Life Recovery

ADVERTISE SOUND Determines wether ADVERTISE SOUND is to be emitted or not by the setting to ON when emitting it and to OFF when not emitting it.

COUNTRY Message language.

Page 34

6-9 COIN ASSIGNMENTS

The “COIN ASSIGNMENTS” mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses “how many coins correspond to how many credits.”

SETTING CHANGE PROCEDURE

Gror) Setting changes cannot be stored unless the TEST BUTTON is pressed

IMPORTANT! while the arrow is on EXIT.

() Press the SERVICE BUTTON to move the arrow to the desired item.

  • Choose the desired setting change item by using the TEST BUTTON.

® To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON. Va

Ne COIN ASSIGNMENTS > COIN CHUTETYPE COMMON @ COIN CHUTE TYPE CREDITTOCONTINUE 1 CREDIT. Sets the combination of the number of COIN COINICREDIT SETTING #1 CHUTEs and the number of players as appli- CHUTEN! 1COIN CREDIT cable. In the case that the COIN CHUTE is changed, be sure the setting is made in a manner CHUTER 1COIN CREDIT meeting the replaced coin chute.

MANUAL SETTING COMMON: >EXIT Coins are accepted in common for both players.

INDIVIDUAL: SELECT WITH SERVICE BUTTON Each player uses a coin chute which accepts coins AND PRESS TEST BUTTON /) independently. @ CREDIT TO START Number of credits required for starting game (1~5 credits are selected.)

@ CREDIT TO CONTINUE Number of credits required for continuing game (1~5 credits are selected.)

@ COIN/CREDIT SETTING Sets the CREDITS increase increment per coin insertion. There are 27 setings from #1 to #27, expressed in XX CREDIT as against XX COINS inserted. (TABLE 6.10a, 6.10b) #27 refers to FREE PLAY. When the COIN CHUTE TYPE is set to INDIVIDUAL, there are some setting numbers not displayed as indicated in TABLE 6.10b.

@ MANUAL SETTING This allows credit increase setting as against coin insertion to be further set in the manner finer than COIN/CREDIT SETTING (refer to TABLE 6.10c).

Page 35

TABLE 6.92 COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)

SETTING FUNCTIONING OF CHUTE#1

SETTING #11 COIN1 CREDIT.
SETTING #21 COIN2 CREDITS
SETTING #31 COIN3 CREDITS
SETTING #41 COIN4 CREDITS
SETTING #51 COIN5 CREDITS
SETTING #61 COIN2 CREDITS
SETTING #71 COIN5 CREDITS
SETTING #81 COIN3 CREDITS
SETTING #91 COIN4 CREDITS
SETTING #101 COIN5 CREDITS
SETTING #111 COIN6 CREDITS
SETTING #122 COINS1 CREDIT
SETTING #131 COIN1 CREDIT
SETTING #141 COIN2 CREDITS
SETTING #151 COIN1 CREDIT

2 COINS 3 CREDITS

SETTING #161 COIN3 CREDITS
SETTING #173 COINS1 CREDIT
SETTING #184 COINS1 CREDIT
SETTING #191 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5 CREDITS

SETTING #201 COIN5 CREDITS
SETTING #215 COINS1 CREDIT
SETTING #221 COIN2 CREDITS
SETTING #232 COINS1 CREDIT

4 COINS 2 CREDITS 5 COINS 3 CREDITS

SETTING #241 COIN3 CREDITS
SETTING #251 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 5 COINS 6 CREDITS

SETTING #261 COIN6 CREDITS

SETTING #27 FREE PLAY

Page 36

TABLE 6.9b COIN/CREDIT SETTING (COIN CHUTE INDIVIDUAL TYPE)

SETTING FUNCTIONING OF COIN CHUTE

SETTING #11 COIN1 CREDIT.
SETTING #61 COIN2 CREDITS
SETTING #81 COIN3 CREDITS
SETTING #91 COIN4 CREDITS
SETTING #101 COIN5 CREDITS
SETTING #111 COIN6 CREDITS
SETTING #122 COINS1 CREDIT.
SETTING #151 COIN1 CREDIT

2 COINS 3 CREDITS

SETTING #173 COINS1 CREDIT.
SETTING #184 COINS1 CREDIT
SETTING #191 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5 CREDITS

SETTING #215 COINS1 CREDIT
SETTING #223 COINS1 CREDIT

5 COINS 2 CREDITS

SETTING #232 COINS1 CREDIT

4 COINS 2 CREDITS 5 COINS 3 CREDITS

SETTING #251 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 5 COINS 6 CREDITS SETTING #27 FREE PLAY

Page 37

MANUAL SETTING

Selecting MANUAL SETTING in the COIN ASSIGNMENTS mode displays the following screen.

MANUAL SETTING

COIN TO CREDITCOIN1 CREDIT

BONUS ADDER NO BONUS ADDER

COIN CHUTE 1 MULTIPUER | 1 COIN COUNTS AS 1 COIN

cON12345S678
crReDIT10200304SGT

COIN CHUT ULTIPLIER 1 COIN COUNTS AS 1 COIN

cON12345678
cReDIT1020300405HT

>EXIT

‘SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

FIG. 6.95 MANUAL SETTING

@ Determines Coin/Credit setting.

@ This sets how many coins should be inserted to obtain one Service Coin.

© This sets how many tokens one coin represents.

Table 6.9c MANUAL SETTING

COIN TO CREDIT 1 COIN1 CREDIT 2 COINS 1 CREDIT 3 COINS 1 CREDIT 4 COINS 1 CREDIT 5 COINS 1 CREDIT 6 COINS 1 CREDIT 7 COINS 1 CREDIT 8 COINS 1 CREDIT 9 COINS 1 CREDIT

BONUS ADDER NO BONUS ADDER 2 COINS GIVE 1 EXTRA COIN 3 COINS GIVE 1 EXTRA COIN 4 COINS GIVE 1 EXTRA COIN 5 COINS GIVE 1 EXTRA COIN 6 COINS GIVE | EXTRA COIN 7 COINS GIVE 1 EXTRA COIN 8 COINS GIVE | EXTRA COIN 9 COINS GIVE 1 EXTRA COIN

COIN CHUTE MULTIPLIER 1 COIN COUNTS AS 1 COIN 1 COIN COUNTS AS 2 COINS 1 COIN COUNTS AS 3 COINS 1 COIN COUNTS AS 4 COINS 1 COIN COUNTS AS 5 COINS 1 COIN COUNTS AS 6 COINS 1 COIN COUNTS AS 7 COINS 1 COIN COUNTS AS 8 COINS 1 COIN COUNTS AS 9 COINS

Page 38

6- 10 GUN SETTING

Selecting GUN SETTING causes the following screen shown at the top to appear. This allows the controller sighting to be adjusted. Periodically check the sighting adjusment status on this screen.

GUN serniNg The screen shown at the left is the sighting GUN MARK CHECK adjustment menu mode. Press the SEVICE > oe USTMENT BUTTON to bring the arrow to the desired adjustment item to select. Press the TEST BUTTON to cause the following sighting check screen and sighting adjustmnet screen to appear. There are 2 types of adjustments, i.e., one for 1P side and one for the 2P side. Adjustments for both 1P and 2P can not be SELECT WITH SERVICE BUTTON made on the same screen. To return to the main ‘AND PRESS Tesh BUTTON menu bring the arrow to EXIT and press TEST BUTTON. (FIG. 6.2)

Selecting GUN MARK CHECK causes the screen at the left to appear. Point the controller at signixpos this screen to have an impact mark appear on the sightYpos a eaten screen. The position of the mark shows the impact point shot by the controller. A red impact mark applies to the 1P side and a blue one to the 2P side. Perform sighting check on this screen. Press the TEST BUTTON to return to the above sighting adjustment meu screen.

~

CURSOR IMPACT MARK (Impact Position)

Select GUN ADJUSTMENT to cause the screen shown on the next page to be displayed. In this screen, the 4 adjustment values can be set. Each adjustment value is set as follows. Be sure to determine the adjustment value by actually pointing the Controller at the end of the designated direction (the cursor value is preset). Select each adjustment position by using the 1P or 2P start button. Press the Test Button to return to the SIGHTING ADJUSTMENT mode.

Page 39

The Cursor is in the pre-setting status. ‘or the actual sighting adjustment, trigger while each end of the on-screen 4 sides aimed at by the Controller regardless of the Cursor. ADXMIN = xxx

Determines the adjustment value of the screen’s left-hand end in the horizontal direction. Point the controller at the screen’s left-hand end to bring the impact mark to the screen’s lefthand end. Determine the adjustment value while actually aiming the Controller at the left hand of the screen and triggering regardless of the cursor. Make adjustments in a manner so that the impact mark is at an appropriate position. At this time, disregard vertical directions. ADXMAX = xxx

Determines the adjustment value of the screen’s right-hand end in the horizontal direction. Point the controller at the screen’s right-hand end to bring the impact mark to the screen’s right-hand end. Determine the adjustment value while actually aiming the Controller at the right hand of the screen and triggering regardless of the cursor.Make adjustments in a manner so that the impact mark is at an appropriate position. At this time, disregard vertical directions.

CENTER= xxx ADYMIN = xxx

Determines the adjustment value of the screen’s upper end in the vertical direction. Point the controller at the screen’s upper end to bring the impact mark to the screen’s upper end. Determine the adjustment value while actually aiming the Controller at the upper end of the screen and triggering regardless of the cursor.. Make adjustments in a manner so that the impact mark is at an appropriate upper end position. At this time, disregard horizontal directions

ADYMAX = xxx

Determines the adjustment value of the screen’s lower end in the vertical direction. Point the controller at the screen’s lower end to bring the impact mark to the screen’s lower end. Determine the adjustment value while actually aiming the Controller at the lower end of the screen and triggering regardless of the cursor.. Make adjustments in a manner so that the impact mark is at an appropriate lower end position. At this time, disregard horizontal directions

Determines the adjustment value of the screens center. X and Y respectively indicates left/right and up/down directions. The left hand side value (aa) indicates the pre-setting value, and the right hand side value (bb) refers to the value to be newly inputted. This is true for all of the above adjustments. By pointing the Controller to the center of the screen, determine the adjustment value while actually aiming the Controller at the center of the screen and triggering regardless of the cursor.

Page 40

6 - 11 BOOKKEEPING

Choosing BOOKKEEPING in the MENU mode displays the data of operating status up to the present are shown on 2 pages. Press the TEST BUTTON to proceed to PAGE 2/2.

SHORTEST PLAY TIME XOXXHXXMXXS

PRESS TEST BUTTON TO CONTINUE

BOOKKEEPING 22

PRESS TEST BUTTON TO EXIT

6 - 12 BACKUP DATA CLEAR

BAKCUP DATA CLEAR

> YES(CLEAR) NO (CANCEL)

‘SELECT WITH SERVICE BUTTON ‘AND PRESS TEST BUTTON COIN CHUTE#*: Number of coins put in each Coin Chute.

TOTAL COINS: Total number of activations of Coin Chutes.

COIN CREDITS: Number of credits registered by inserting coins.

SERVICE CREDITS: Credits registered by the SERVICE BUTTON.

TOTAL CREDITS: Total number of credits (COIN CREDITS+SERVICE CREDITS).

TOTAL TIME: The total energized time.

On page (2/2), each play frequency is displayed. When setting difficulty levels, the frequency can be reffered to as a standard.

When in the PAGE 2/2 mode, press the TEST BUTTON to return to the MENU mode (FIG. 6.2).

Clears the contents of BOOKKEEPING and high score player ranking entry. When clearing, bring the arrow to “YES” and when not clearing, to “NO”, by using the SER- VICE BUTTON, and push the TEST BUTTON. When the data has been cleared, “COMPLETED” will be displayed. Bring the arrow to “NO” and press the TEST BUTTON to cause the MENU mode to return on to the screen.

Note that the contents of the game setting and sighting adjustment are not affected by BACKUP DATA CLEAR operation.
Page 41
  • CONTROLLER (GUN)

A @ In order to prevent an electric shock and short circuit, be sure to turn

power off before performing work by touching the interior parts of

WARNING! the product.

7-1 @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident.

In the cases where the controller’s operation is not satisfactory of the controller sight deviates from the direction in which the controller is pointed, it is possible that some maintenance may be required (the controller’s interior parts may have been damaged). Replace the parts by disassembling the controller in the following procedure: Also, be sure to perform sighting check in the TEST mode when the controller parts are replaced.

REPLACING THE MICROSWITCH @ Disassemble the controller. ©) Pull out the microswitch from COVER RIGHT. ©) Take out the microswitch by removing the soldering from it.

  • Solder the new microswitch and assemble the controller.

REPLACING THE SENSOR BOARD

The sensor board fits in between LENS HOLDER L and LENS HOLDER R. Replace the sensor board by disassembling sensor unit in the following procedure:

® Disassemble the controller.

@ Remove the sensor unit from COVER R.

Page 42

BLACK M3

SENSOR UNIT

COVER LEFT COVER RIGHT

MICRO SWITCH

SAO

SCREW (6) _” ) M3x25 PH PN M3x8 PH PN

Page 43
  • COIN SELECTOR

HANDLING THE COIN JAM

to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: (@ Turn the power for the machine OFF. Open the coin chute door. Open the gate and dust off by using a soft brush (made of wool, etc.). @ Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. @) Remove the CRADLE. When removing the retaining ring(Ering), be very careful so as not to bend the shaft. ©) Remove stain from the shaft and pillow portions by wiping off with a soft cloth, etc. © After wiping as per #5 above, further apply a dry cloth, etc. to cause the coin selector to dry completely.

@ Never apply machine oil, etc. to the coin selector @ After cleaning the Coin Selecting,

IMPORTANT! Insert a regular coin in the normal working status and ensure that the Selector correctly functions. ©

COIN INSERTION TEST while Keeping

Once a month, when performing the COIN SW Butiont pressed

TEST, simultaneously check the following: down and check if it is O Does the Coin Meter count satisfactorily? relecte O Does the coin drop into the Cashbox correctly? O Is the coin rejected when inserted while keeping the REJECT BUTTON pressed down? If the coin is not rejected when the REJECT BUTTON is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check

FIG.8b

COIN METER

Page 44

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON LOST WORLD DLX COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATORS:

HOLE POSITION#1 VFMS-AE 2400-GL 5 (MARS)

(FORWARD-MOST POSITION) AL4 (MARS)

HOLE POSITION#2 VFM2-AE 2400-GL 5 (MARS)

VFM4-AE 2400-GL 5 (MARS) DBV45 (JCM)

HOLE POSITION #3 CURRENTLY NOT USED

HOLE POSITION #4 Dsio1*

*The back flange on the chute can be removed for hole position #4. If the flange is not removed, it may interfere with the back of the cabinent.

Page 45
  • PROJECTOR

Since the Projector has been adjusted at the time of shipment, avoid making further adjustments without good reason.

CAUTION!

tion caused by the geomagnetism at the time of installation, location, and peripheral magnetic field. After the installation of machine, and before commencing operation, check for Convergence deviation and if

IMPORTANT! deviated, make adjustments. : The Projector is subject to color deviation due to Convergence devia-

Fine adjustments are stored in the Projector. Pressing the Fine Adjustment SW (Convergence Adjustment) results in entering the Fine Adjustment mode, and this may cause the stored fine adjustment to be changed. During work other than for adjustment, Should you touch the Fine Adjustment SW by mistake, immediately turn power off by using the main SW and then turn it back on again. If any distortion or color deviation is found in the test mode and adjustments are needed, use the specified adjustment knob, or perform adjustment by remote control. To find the adjustment knob, move Cabinet DX and remove the PTV Front Service Door by using the procedure opposite the one for installing and assembling. In some cases a cover is installed to the Adjustment Knobs. Remove the Cover.

9 - 1 CLEANING THE SCREEN

Since the Projector screen is susceptible to damage, pay careful attention to it’s handling. When cleaning, refrain from using water or volatile chemical.

CAUTION!

When the screen surface becomes dirty with dust, etc., clean it by using a soft cloth such as gauze. When water, and volatile chemicals such as benzine, thinner, etc., spill on the screen surface, it may be subject to damage, therefore, do not use them. Also, since the surfaces are susceptible to damage, refrain from rubbing them with a hard material or using a duster.

FIG. 9.1

Page 46

9-2 MITSUBISHI PROJECTOR

CJ MITSUBISHI PROJECTOR CONTROL PANEL

POWER BUTTON

8968656600006 0 &

Convergence Adjustment SW @ VPOS g H.POS @RGAIN @G-GaIN (©) B-GAIN (@) CONT BRI @vw ) HW @ RHL. Linearity adjustments in horizontal directions QW BAL. (red or blue) are made.

STATIC CONVERGENCE ADJUSTMENT

@test Test mode on/off key ®re RIB key @ <j Left shift key ep Right shift key Convergence Adjustment SW

A ev Lower shift key a @ FAN Upper shift key (1 POWER Power button

@ For the Convergence adjustment mode, press the test mode on/off key. ©) @ Ensure that “R” is displayed on the screen. Make adjustments so as to cause the red cross pattern to match with the green cross pattern by using Left shift key , Right shift key (5) , Lower shift key (16) , and

Upper shift key @M ‘

@ By using R/B shift key @ , cause the red adjustment “R” to shift to blue adjustment “B” and make sure that “B” is displayed on the screen. ® In the same manner as in@) above, cause the blue cross pattern to match with the green cross pattern. After making adjustment, press the test mode on/off key ® to cancel the convergence adjustment mode.

Page 47

STATIC CONVERGENCE ADJUSTMENT METHOD WITH REMOTE CONTROL

@ Although Remote Control Buttons other than those specified below do not function even if pressed during Convergence Adjust-

Gror) ment, do not press them during adjustment work so as to avoid

causing malfunctioning.

IMPORTANT! @ Operate the Remote Control towards the PTV screen. If directed

other than to the PTV screen, the Remote Control does not function.

BEFORE USING REMOTE CONTROL: First make sure that the main SW on the Projector’s control panel is ON (the LED adjascent to the main SW is lit). The Remote Control has 2 different types. Depending on the type, the Adjustment procedure is different.

In case of REMOTE CONTROL (Part No. 200-5298): ® For the Convergence Adjustment mode, press the test button. Ensure that “R” is displayed on the screen.

@ Make adjustment so as to cause the red cross pattern to match with the green cross pattern. When the red cross matches the green cross, the green cross turns yellow or white.

Use remote control buttons shown below to move the red cross as follows:

Button, ® ——— to the left to the right Upward ———— Downward

Use Remote Control button 6 to shift “R” to “B”. Make sure that “B” is displayed on the screen. Each time Button ©Ois pressed, red and blue adjustments are shifted.

® In the same manner as in@Q)above, cause the blue

cross to match the green cross. When the blue cross matches the green cross, the green cross turns white. ® After adjustment is made, press the test button to cancel the Convergence Adjustment mode. *When 2 minutes or more elapses in the Conver-

gence mode screen without taking any action, the 20304 L

on-screen adjustment mode will disappear. H

Page 48

In case of REMOTE CONTROL (Part No. 200-5532):

@ Press the TEST KEY to have the red line adjustment screen appear.

® Superimpose the red cross on the green cross at the center of the screen. Move the red cross to the left, right, up, and down respectively with the corresponding buttons of the remote control. When the red cross green cross, the green cross turns into yellow or white. Red line adjustment

superimposed on the

® Press the R/B Key to have the blue line adjustment screen appear. Each time R/B Key is Press SHIFT to superimpose the pressed, the red line and blue line will be red line on the green line. alternated.

@® Inthe manner similar to@)above, press each key to superimpose the blue cross on the green cross. When it is superimposed, the cross in the center will become white.

® Press the TEST KEY to exit from the adjustment mode. Completion of Adjustment

During STATIC CONVERGENCE Adjustment Mode, if no action is taken within 5 minutes, the adjustment mode will be exited automatically.

Page 49
  • REPLACEMENT OF FLUORESCENT LAMP AND LAMPS

@ When performing the work, be sure to turn power off. Working with power on can cause an electric shock or short circuit accident. @ The Flourescent Lamp, when it gets hot, can cause burns. Be very careful when replacing the Fluorescent Lamp.

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Not using a step or using an unstable step can cause a violent falling down accident.

CAUTION!

10-1 REPLACEMENT OF FLUORESCENT LAMP AND TURNING LAMP (PATO LAMP)

TRUSS SCREW (4) SCREW (2) M4x12 TMPR PRF M4x12 TMPR PRF WSHR FL (2) ——~ Al FL COVER

PATO LID

SPARE LAMP.

PREPARE A STEP IN ADVANCE TO PERFORM WORK.

Page 50

10-2 REPLACEMENT OF BUTTON LAMP

  • Take out the tamperproof screws and remove the Control Panel.

® Pull the lower part of the switch from the rear part and replace the Lamp.

  • 32x20 TMPR PRF WSRR (8) #8 LAMP 6V 3W.

al ©

10-3 REPLACEMENT OF ROOM LAMP

Take out the 6 Flat Head screws to remove the Lamp Plate, and replace the Lamp.

LAMP 120V 40W

FLAT HEAD SCREW (6)

LAMP PLATE

Page 51
  • PERIODIC INSPECTION TABLE

The items listed below require periodic check and maintenance to retain the performance of this machine and ensure safe operation. When handling the controller, the player will be in direct contact with it. In order to always allow the player to enjoy the game, be sure to clean it regularly.

@ Be sure to check once a year to see if Power Cords are damaged, the plug is securley inserted, dust is accumulated between the ; Socket Outlet and the Power Plug, etc. Using the product with

WARNING! dust as is accumulated can cause a fire or electrical shock. @ Periodically once a year, request the place of contact herin stated or the Distributer, etc. where the product was purchased from, as regards the interior cleaning. Using the product with dust as is

accumulated in the interior without cleaning can cause a fire or

accident. Note that cleaning the interior parts can be performed on a pay-basis.

ITEMS DESCRIPTION PERIOD REERENCE

CONTROLLERCleaningas required
Sight checkWeekly6
Check SwMonthly6

COIN SELECTOR Check COIN SW Monthly 6

COIN SELECTOR cleaning | _Trimonthly 8

PROJECTORC.R.T. cleaningweekly9
Check adjustmentsMonthly3,6,9
GAME BDSetting checkmonthly6
INTERIORCleaningAnnuallysee above.

POWER PLUG Inspection and cleaning

CABINET SURFACECleaningAs necessary | see below

CABINET Ensure that adjusters are in contact with the floor As necessary

CLEANING CABINET SURFACES

When the cabinet surfaces are badly soiled, remove stains with a soft cloth dipped in water or diluted (with water) chemical detergent and squezzed dry. To avoid damaging surface finish, do not use such solvents as thinner, benzine, etc. other than ethyl alcohol, or abrasives, bleaching agent and chemical dustcloth.

Page 52

12. TROUBLESHOOTING Should trouble occur, first check connector connections.

PROBLEMSCAUSECOUNTERMEASURES
With Main SWPower is not supplied.Plug in correctly

ON, no activation Power supply/voltage is not correct.

AC main fuse causes the power to be cut off due to momentary Make sure that power supply/voltage is

Check fuse. Remove the cause of overload and replace fuse overload.

PTV screen isPOWER SW is OFF1> Check to see if the power SW is ON.

blackened and no

sound is emitted.Connections within the base are2.> Check the BNC connector connections

defective. of the PTV TERMINAL BD and VPM BUFFER BD in CONTROL CABI.

3.> Check the Main Fuse.

PTV screen is allIrregular communications between1> Check the communication cable

blue. each board. connection between the Game BD and T/O BD.

2> Turn the Power SW back on again.

The color of the Connector connections are defective. | Check the connection for the RGB and image on PTV SYNC connectors of the PTV TERMINAL screen is incorrect. BD and VPM BUFFER BD.

The image on PTV Affected by the magnetic field of screen has color installation location. deviation. Make CONVERGENCE adjustment. (Refer to Section 9.)

No sound is emitted.|_ Sound Volume adjustment is not appropriate.

Sound BD and speaker are Adjust sound volume. (see Section 6).

Perform sound test to find and replace malfunctioning. defective parts.(Refer to Section 6).

Controller opera-Due to enviromental changes, etc.,Perform sighting adjustment in the TEST
tion is not satis-sighting became inappropriate.mode (See Section 6).

factory. Microswitch malfuntioning. Replace the microswitch (See Section 7).

Sensor BD malfunctioning. Replace the sensor BD (See Section 7).

The FluorescentThe Fluorescent tube is burnt out.Replace the Fluorescent tube

lamp does not (Refer to Section 10). light up.

The Spot and/orLamp FaultReplace the Lamp

Turning lamp does not light up. (Refer to Section 10).

Page 53

12-1 REPLACEMENT OF LED BOARD

REPLACEMENT OF LED BOARD

In case of no light emission from the 2 LED’s, LED fault or malfunctioning may be considered. Replace by using the following procedure. Also, use the procedure below when wiping off surface soils after seperating the Front Cabinet and PIV.

Replace the LED in case of no light emission from the 2 LED’s.

iC) Turn power off.

© Seperate the Front Cabinet and the PTV. Since there are wiring connections inside, pay attention so as not to damage wirings when seperating the Front Cabinet and the PTV.

  • The LED Board is inside the Mask of the Front Cabinet. Disconnect the connectors from both ends of the malfunctioning LED Board, take out the 2 U Nuts to remove the LED Board and then replace it.

LED BOARD

fraca]

Page 54
  • GAME BOARD
CAUTION! @ In order to prevent an electrical shock, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident.

Do not expose the Game BD, etc. without a good reason. In this product, setting changes are made during the test mode. The Game BD need not be operated. Use the Game BD, etc. as is with the same setting made at the time of shipment. The electronic parts on the IC Board could be damaged due to human static electricity. Before performing IC Board related work, be sure to discharge physically accumulated statics by touching grounded metallic surfaces. When asking for the replacement or repair of the product’s Game Board (MODEL 3 BOARD), be sure to put the Game Board together with the Shield Case in the Carton Box.

13 - 1 REMOVING THE BOARD

To replace the IC Board (such as the GAME BOARD, I/O BOARD), take out the IC BOARD by using the following procedure.

© Turn power off.

@ Take out the 2 screws to unlock, and remove the right-hand side Maintenance Lid.

@® Disconnect all of the Connectors which are connected to the Shield Case Filter Board.

@ Take out the 2 screws which secure the Wooden Base, and pull out the Shield Case together with the Base.

© Take out the 3 screws and remove the Case Lid to have the Game Board appear.

TRUSS SCREW (2) -»' M4x30 SCREW (3) M4x8 w/fl spring wshr CASE LID

SCREW (2) M5x30 w/fl spring wshr

FILTER BOARD

SHIELD CASE

MAINTENACE LID

Page 55

13 - 2 COMPOSITION OF GAME BOARD

\ é

DESCRIPTION 837-12874 837-12874-01 MODEL3 STEP 1.5 CPU BOARD MODEL3 STEP 1.5 CPU BD W/GND BD MODEL3 STEP 1.5 VIDEO BOARD ROM BD THE LOST WORLD 837-12875

834-13172

NOTE: PICTURE IS ONLY FOR REFERENCE, UNIT IS NOT TO BE OPENED. EXPOS- ING THE BOARD FOR ANY REASON MAY VOID WARRANTY.
Page 56

JPT-423-0300

‘BLLBOARD PLATE PT

JPT-1051-B IPT3212-B IPT-429-0143 SICKER SDE STICKER CONPTS L PP PL PT

JPT-1051-C

STICKER SDE R

JPT-3201-C 421-9594

‘STICKER NSTR PT

‘STICKER ACRYL REAR

JPT-3151-B

‘STICKER REAR BASE PT

STICKER ACRYL SDE R

\

JPT-2101-B 422-0624 CONT PL SHEET FT \ PLAY NSTR SEET FT H as | : i i J /

\__ JPT-0001 ‘DENM PLATE PI

  • DESIGN RELATED PARTS
Page 57
  • PARTS LIST ‘) TOP ASSY THE LOST WORLD DX (D-1/2)

THE LOST, WORLD

Page 58

a) TOP ASSY THE LOST WORLD DX

ITEM NO. PART NO.

1 JPT-0500 2 JPT-1000 3 JPT-1100 4 JPT-2100 5 JPT-3000 6 5091-5712-01 13 N/A 14 JPT-3212 15 JPT-3213 16 422-0624-01

17 JPT-1053 (D-2/2)

DESCRIPTION

ASSY BILLBOARD ASSY FRONT CABI ASSY PTV ASSY CNTRL PNL ASSY REAR CABI SW PB W/L 6V YELLW SERIAL NUMBER STICKER AURICLE L AURICLE R PLAYER INSTR SHEET

CONN LID

Page 59

@) ASSY BILLBOARD (JPT-0500)

ITEM NO.

Ake PART NO.

JPT-0501 IPT-0503 423-0300 429-0143

390-5695-20EX. LOCAL PURCHASE

LOCAL PURCHASE DESCRIPTION

BILLBOARD BOX FL COVER BILLBOARD PLATE JPT POP PNL JPT

ASSY FL20W EX W/CONN HIGH T CE PAT LAMP YELLOW TRI-LITE, MODEL MV 110 ( #25T8DC ) 120V 25W FL LAMP BULB

Page 60

@ ASSY FRONT CABI (JPT-1000) (0-1/2)

Page 61

@) ASSY FRONT CABI (JPT-1000)

ITEM NO.

Sowmrgaunane PART NO.

JPT1-1020 JPT-1050 JPT-1070 JPT-1075 JPT-1080 JPT-2100 JPT-4000 JPT1-4100 JPT-4200 (D-2/2)

DESCRIPTION

AC UNIT ASSY SUB FRONT CABI ASSY SPEAKER FL ASSY SPEAKER FR ASSY MASK ASSY CNTRL PNL ASSY MAIN BD ASSY PWR SPLY ASSY GUN SENSE BD

Page 62

® AC UNIT (JPT1-1020

O° fe)

om | —

fe) °o

ITEM NO. PART NO. DESCRIPTION

1N/AAC BRKT
2N/ALINE STRAIN RELIEF
35091-5234MAIN ROCKER SW 25A
Page 63

® ASSY SUB FRONT CABI (JPT-1050) (0-1/3)

SECTION X-X

Page 64

® ASSY SUB FRONT CABI (JPT-1050)

ITEM NO. PART NO.

JPT-1025 JPT1-1030 JPT-1051 JPT-1052 JPT-1054 ARC-1006 253-5396 999-0167 253-5366

220-5237 999-0169 (D-2/3)

DESCRIPTION

ASSY WOOFER SW UNIT FRONT CABI CENTER LID JOINT BRKT LEG BRKT CABINET HANDLE LEG ADJUSTER BOLT 1/2x13x3 CASH BOX

COINDOOR ASSY CASTER 2 1/2"

Page 65

@ ASSY WOOFER (JPT-1025)

ITEM NO. PART NO. DESCRIPTION

1 N/A BRKT WOOFER 101 130-5172 SPEAKER SUB WOOFER-BASS SHAKER

Page 66

SW UNIT (JPTI-1030;

|COIN METER]

Test Service Oo

[}——_ °° O-- ow) SHAKER

Volume Front Volume Rear

ITEM NO. PART NO. DESCRIPTION

1 N/A SW BRKT 2 N/A VOL COVER

101220-5179VOL CONT B-5K OHM
103509-5028SW PB 1M
104601-0042KNOB 22 M
Page 67

ASSY SPEAKER FL (JPT-1070)

(JPT-1075)

{

ITEM NO. PART NO.

1 JPT-3203 2 JPT-3204

101 130-5156 DESCRIPTION

SPEAKER COVER L SPEAKER COVER R

SPEAKER BOX 80HM 20W

Page 68

(@ ASSY MASK (JPT-1080)

ITEM NO. PART NO. DESCRIPTION

1 JPT-1081 MASK BASE 2 JPT-1082 IR COVER

101 838-13145 LED BD GUN SENSE

Page 69

ASSY PTV (JPT-1100)

ITEM NO.

URwUNe PART NO.

JPT-1101 JPT-1102 200-5277 2000-5350 999-0276

200-5265

SEE A

DESCRIPTION

BRACKET PTV LID CONN PTV LENTICULAR SHEET FRESNEL SHEET LEXAN PROTECTOR SHEET

ASSY PROJECTION DISPLAY JPT

Page 70

@ CONTROL UNIT 1P (JPT1-2000) (0-1/2)

the Actuator so as to allow the Trigger of © to turn

and adjust

NOTE: When assembling ©, bend the Actuator as_shown in the Detail FIG.

the Microswitch ON-OFF correctly.

Page 71

@) CONTROL UNIT 1P (JPT1-2000)

ITEM NO. PART NO.

1 JPT-2030 2 COP-2005 3 125-5124 4 253-5404-02 5 253-5405-02 6 253-5406-02 7 999-0675

101 280-5124-03 102 509-5080 201 000-P00308-0B 202 012-P00308 203 FAS-000015 204 FAS-500006 205 060-F00300 (D-2/2)

DESCRIPTION

SENSOR UNIT STOPPER PIN TORSION SPRING COVER LEFT RED COVER RIGHT RED TRIGGER RED PROTECT TUBE W/WIRE; COUPLING; WASHER

NYLON CLAMP NK03 SW MICRO TYPE M SCR PH BLK M3 X8 TAP SCR#2 PH 3 X8 M SCR PH BLK M3X8 CAP NUT TYPE 3 BLK M3 FLT WSHR M3

Page 72

@3 SENSOR UNIT (JPT-2030)

ITEM NO. PART NO. DESCRIPTION

1 JPT-2031 SENSOR HOLDER

101 838-13144 SENSOR BD GUN SENSE

201 012-P00306 TAP SCR #2 PH 3X6

Page 73

@,_DETAILS

NOTE: When assembling (03, bend the Actuator as shown in the Detail FIG,

and adjust the Actuator so as to allow the Trigger of © to turn

the Microswitch ON-OFF correctly. @ CONTROL UNIT 2P (JPT1-2050) (D-1/2)

Page 74
  • CONTROL UNIT 2P (JPT1-2050)

ITEM NO. PART NO.

1 JPT-2030 2 COP-2005 3 125-5124 4 253-5404-01 5 253-5405-01 6 253-5406-01 7 999-0675

101 280-5124-03 102 509-5080 201 000-P00308-0B 202 012-P00308 203 FAS-000015 204 FAS-500006 205 060-F00300 (D-2/2)

DESCRIPTION

SENSOR UNIT STOPPER PIN TORSION SPRING COVER LEFT BLUE COVER RIGHT BLUE TRIGGER BLUE PROTECT TUBE W/WIRE; COUPLING; WASHER

NYLON CLAMP NK03 SW MICRO TYPE M SCR PH BLK M3 X8& TAP SCR#2 PH 3 X8 M SCR PH BLK M3X8 CAP NUT TYPE 3 BLK M3 FLT WSHR M3

Page 75

ASSY REAR CABI (JPTO-3000)

Ue o 8 aby SEEB

SEE B

  • FRONT 4 CAPSTOP. VS RUNNER STANDBY ‘MAGNET RUNNER

DETAILS: CURTAIN PORTION

£ es — Ci u oi TT

  • § SEE A . 3 a 1 Fy s SEE A 7 & SEALS IO OL

ITEM NO. PART NO. DESCRIPTION,

1JPTO-3100ASSY REAR BASE
2JPTO-3200ASSY REAR FRAME
3JPTO-3001REAR PILLAR
4JPT1-3002CURTAIN L
5JPT1-3003CURTAIN R
6N/ASTICKER CAUTION FORK
101601-9519CURTAIN RAIL
201030-000820-SBHEX BLT W/S BLK M8x20
202030-000860-SBHEX BLT W/S BLK M8X60
203060-f00800-0bFLT WSHR BLK M8
204000-P00412-SM SCR PH W/S M4x12
Page 76

@® ASSY REAR BASE (JPTO-3100)

ITEM NO. PART NO.

JPT1-2000 JPT1-2050 JPT-3150 JPT-3101

000-T00416-0B DESCRIPTION

CONTROL UNIT 1P BLUE CONTROL UNIT 2P RED ASSY REAR BASE TUBE CLAMP

M SCR TH BLK M4x16

Page 77

4 ASSY SUB REAR BASE (JPT-3150) (0-1/2)

raat eo c

GENAGAS S¥it ONFLSHOS

s ies

Page 78

rz) ASSY SUB REAR BASE (JPT-3150)

ITEM NO.

CIADKHAWNHE

ll PART NO.

JPT-3151 JPT-3152 JPT-3153 JPT-3154 JPT-3155 JPT-3156 JPT-3157 JPT-3158 JPT-3159 JPT-3160 JPT-3161 JPT-3162 JPT-3163 JPT-3164 JPT-3165 IJPT-3166 JPT-3167 JPT-3168 JPT-3169 JPT-3170 JPT-3171 117-5233 SCR-1008 999-0167

999-0169 DESCRIPTION

REAR BASE REAR BASE LID SEAT CARPET SEAT SASH SEAT SASH MID GUN HOLDER L GUN HOLDER R HOLDER SHAFT HOLDER PAD FRONT STAND L. FRONT STAND R REAR STAND L REAR STAND R FLOOR MAT MAT EDGE F MAT EDGE C MAT EDGE S MAT EDGER CHEST LID LEG BRAKT SUSPENSION PLATE PLATE LEG BRACKETBLACK NUT PLATE FOR CASTER LEG ADJUSTER BOLT 1/2x13x3

CASTER 2 1/2" (D-2/2)

Page 79

-1/2) O 3200)

@ ASSY REAR FRAME (JPTO

Page 80

@ ASSY REAR FRAME (JPT0-3200) (0-2/2)

ITEM NO. PART NO. DESCRIPTION

1IPT-3250ASSY SPEAKER RL
2IPT-3255ASSY SPEAKER RR
3.JPTO-3201REAR FRAME
4IPT-3202ROOF LID
5JPT-3203SPEAKER COVER L
6IPT-3204SPEAKER COVER R
7IPT-3205SIDE WINDOW L.
8IPT-3206SIDE WINDOW R
9IPT-3207REAR WINDOW
10IPT-3208REAR WINDOW SASH L
11IPT-3209REAR WINDOW SASH R
12IPT-3210REAR WINDOW SASH D
13JPT-3211ROOF PLATE
14IPT-3212AURICLE L
15IPT-3213AURICLE R
16JPT-3214XLAMP PLATE
17IPT-3215SIDE WINDOW SASH.
101260-0011-02AXIAL FAN AC 100V 50-60HZ
103LOCAL PURCHASELAMP 110V 30W SINGLE AR
Page 81

@ ASSY SPEAKER RL (JPT-3250)

ITEM NO. PART NO. DESCRIPTION

1 JPT-3251X SPEAKER BRKT L

101 130-5162 GULL BOX SPEAKER 80HM 8W

Page 82

@ ASSY SPEAKER RR (JPT-3255)

ITEM NO. PART NO. DESCRIPTION

1 IPT-3256X SPEAKER BRKT R

101 130-5162 GULL BOX SPEAKER 80HM 8W

Page 83

( ASSY MAIN BD (JPT-4000) ASSY SHIELD CASE (JPT-0100)

Page 84

(@ ASSY MAIN BD (JPT-4000) ASSY SHIELD CASE (JPT-0100)

ITEM NO. PART NO. DESCRIPTION

laN/ASHIELD CASE MODEL 3
3aN/AFILTER BD MODEL 3 JPT
6aN/ASTICKER 833-13171
1N/AASSY SHIELD CASE
2N/AMAIN BD BASE
3N/ASHIELD CASE BRKT
6N/AGAME BD JPT

THESE PARTS ARE NOT AVAILABLE SEPERATELY INSTEAD THEY ARE SOLD AS A COMPLETE UNIT.

ALL JPT-4000 ASSY MAIN BD

Page 85

ASSY PWR SPLY (JPT1-4100)

Page 86

ASSY PWR SPLY (JPT-4100)

ITEM NO. PART NO.

1 838-13142 2 999-0677

101 838-11651-91 102 838-11650-01 103 838-11650-28 104 LOCAL PURCHASE

105 N/A 106 838-11855 107 260-001 1-02 (0-2/2)

DESCRIPTION

BASS AMP 50Wx2 AUDIO XFMR 12.8V 6Ax2 23V 9.6Ax2

LOWPASS AMP EQ.PWR AMP JPT A EQ. PWR AMP JPT B FUSES; EQ AMP FUSES, PTV FUSE, MAIN FUSE 4A slo, 5A slox2, 8A slo GND BRCKT SSR CONN BD AXIAL FLOW FAN AC 120V 50-60HZ

Page 87

© ASSY GUN SENSE BD (JPT-4200)

ITEM NO. PART NO. DESCRIPTION

101 400-5330-02 POWER SUPPLY 102 838-13146 GUN SENSE BD

Page 88

Come see Sega GameWorks Service Department’s Homepage

Netscape: Welcome to Sega GameWorks! Go To: [http if www .sgwservice.com/

Welcome to the

Service Department Home Page

The following options are available to you :

What's new on the site Check Here

Look up your local Sega Distributor

Go to Individual Manuals and Bulletins

Find an Individual Part Number

Find a Manual Part Number

Get Info on your Game Monitor

Get Info on your Board System

Talk to the Service Staff

Sign up to Receive Service Bulletins

What is going on in Darl's Office

Sega Game Works Service Department Phone (415)-802-1750 Fax (415)-802-1754

Page 89

SEG

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 415/650-802-1750 phone 415/650-802-1754 fax