Crystal Castles ST-241-01 Backdoor Sheet
Crystal Castles (version 4) (Atari, 1983) · Backdoor Sheet · 1 pages · original scan
Auxiliary Coin Switch
Self-Test Switch
Volume Controt To increase turn clockwise Game PCB
OFF at on
A n
Switch Locations
Setting the Coin Counter Switch
The illustration above shows the location of the dualinline-package (DIP) switch on the game printedcircuit board (PCB). Toggle 1 of this switch is the only switch that is used. When set to the ON position, the left and right coin counter outputs of the game PCBare paralleled together. Therefore, any coin received from the right or left coin inputs will be counted on one counter connected to either the left or right coin-counter output. The US-built games have one coin counter. Therefore, on US-built games, toggle 1 of the switch should be set to ON. When toggle 1 is set to OFF, a second coin counter must be connected to the unconnected coin counter output. For Ireland-built games, the second coin counter is standard. Therefore, on Ireland-built games, toggle 1 of the switch should be set to OFF.
Self-Test
This game will test itselfand provide data to show that the audibly thcough the spzakers. No additional equipment
game circuitry and controls are operating properly. Selftest data is presented visually on the video display and
is required. We suggest you perform a self-test when you first set up, each time you collect money, change the game options, or suspect game failure.
Table 1 RAM Failure Tone Sequence
Tone Sequence
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | PCB Location |
| High | Low | Low | low | Low | Low | Low | RAM at 4E |
| High | High | Low | Low | Low | low | Low | RAM at 4F |
| High | High | High | Low | Low | Low | Low | RAM at 4H |
| High | High | High | High | Low | = Low_— | Low | RAMat 4J |
| High | High) | = High) Ss High = High | Low | Low | RAM at 6B | ||
| High | High | High | High | High | High |
Low RAM at 6D
Entering Self-Test
‘To enter the self-test mode, set the self-test switch on the
utility panel tothe ON(up)position. The game tests the random-access memory (RAM), the bit-mode circuitry,
custom Input/Output (1/0) integrated circuits (ICs), the
the electronically erasable read-only memory (EEROM),
and the read-only memory (ROM). Figure 1_ shows the resulting video display if these tests pass. The custom 1/0 testis the only test not shown on the video display. If this test passes, you will hear sounds that range froma low frequency toa high frequency.
Figure 1 Test Passes Video Display Ifthe RAM fails, a sequence of seven “beep” sounds will be emitted from the game speakers, followed by a pause, then the sounds will be repeated. Table 1 identifies the failing RAM for the emitted sounds. In this table, the “High” indicates high tones from the game speaker and the “Low” indicates low tones. If the bit-mode circuitry fails, a sequence of “beep” sounds will be emitted as follows: High, low, high, low, low, low, low. If the EEROM fails, the video display will identify the failed IC as shown in Figure 2. The display will indicate a failed IC at either location 4A or 4B.
cerom FRTLURE AT PC NE
Figure 2 EEROM Failure Video Display Ifa ROM fails, the video display will be as shown in Figare
- In this figure, integrated circuit IL has failed. The correct checksums are as follows: checksum 01 for 1K, 02 for 1L, 03 for IN, 04 for 1H, and 05 for 1. Checksums of any other value indicate a failure for that IC.
cHeresum
SHEEKsuM
Figure 3 ROM Failure Video Display
Self-Test Main Menu
If all initial self-tests pass, the main menu will he displayed as shown in Figure 4. This menu allows you to select from seven different items. As indicated at the bottom of the display, set the self-test switch to off (down) to exit from self-test.
ROVANCE wore Le
> sere
CLERR RECOUNTING
GRME OPTIONS
Test ceRrom SHITCH TEST RESET HALL OF FRME
SWITCH SELF TEST SNITCH TO EXIT
Figure 4 Self-Test Main Menu Video Display Grid Display The grid display shown in Figure 5 is used for adjusting the video display. When properly adjusted, the grid should be white on a black background. The corners of the grid should just barely go off the cor- “ners of the display.
Figure 5 Grid Video Display
Accounting Display The accounting display shown in Figure 6 is used for displaying historical information about the game. The photograph shown in Figure 6 was taken of an engineering prototype game. Therefore, in our example, no coins are shown for the left mechanism and only two coins for the right mechanism; but 46 coin credits are shown for the auxiliary coin switch. Ordinarily, the coin information is never cleared unless the EEROM are changed or damaged. Thus, this information may be compared with the information from the mechanical coin counter(s) for determining the accuracy of the mechanical coin counters. The most important information shown on the accounting display is the average game time. This time should be between 2 and 3 minutes. The display in Figure 6 is a good example of optimum game time. A histogram of game time is shown at the bot tom of the screen.
RECOUNTING
nUux corns npooNNes HISTOGRAM m2 SUNNED BREEN EON seegoos Boceseces
Figure 6 Accounting Video Display
Clear Accounting Display The clear accounting video display is shown in Figure 7. Note that the coin information is never cleared.
RECOUNTING
ux _coxNs
MISTOGRRM
+e 2:28 ie 2 8 aa 2 88 2 af woru eu
Figure 7 Clear Accounting Video Display Game Options Menu The manufacturer's recommended game options are shown in Figure 8. To move the arrow that points to each selectable option, press the left JUMP button. ‘To change the option, press the right JUMP button. Allavailable options are as follows: COIN VALUE. The coin-value option determines the number of coins entering the left or right coin mechanisms, required to play one game. The values available are ¥2, 1, or 2. For game demonstrations, the FREE PLAY option is also available. LEFT MECH VALUE. The available left mechanism values are 1 or 2. The chosen value multiplies the coins received in this mechanism by that value. When set to I, a coin dropped into the left coin mechanism of the coin door has the value of 1 coin. When set to 2, a. coin dropped into this mechanism has the value of 2. RIGHT MECH VALUE. The available right mechanism values are 1, 4, 5, or 6. The chosen value multiplies the coins received in this mechanism by that value. This option makes it possible to receive coins with a higher denomination than the left mechanism
GAME DIFFICULTY. This option allows you to increase or decrease the difficulty of the game, thus increasing or decreasing the average game time. When used with the accounting display, you may tune the game for the optimum game time of 2 minutes and. 30 seconds by setting this option to EASY, MEDIUM, HARD, or HARDEST. STARTING LIVES. This option allows you to increase the number of lives per game from 3 to 5. The available options are 3, 4, and 5. Using this option along with the accounting display will allow you to tune the game for an optimum average game time of 2 minutes and 30 seconds. EXTRA LIVES. This option allows you to award bonus lives for evéry 70,000 points scored. The available options are YES and NO. Using this option along with the accounting display will allow you to tune the game for the optimum average game time of 2 minutes and 30 seconds. RESTORE FACTORY OPTIONS. This option allows you to restore the options to those retained in the game program memory. These factory-recummended options are shown in Figure 8 EXIT. This is not an option, put the way back to the main menu.
COIN vRLUE cert Mecn vmuc ok RIGHT MECH VALUE 2 Grwe orerreucty = MEOrUM STARTING LIVES a
EXTRA LIVES ves
RESTERE FRETORY OPTIONS
exx?
Figure 8 Game Options Video Display
Test EEROM Display If the EEROM test passes, the results of the test are shown in Figure 9. If either EEROM integrated circuit 4A or 4B fails, the failed IC will be displayed as shown in Figure 2. However, the message RAM OK will not be displayed.
Figure 9 EEROM Test OK Video Display Switch Test Display In the switch test, the left, right, and auxiliary coin switches; the left and right JUMP switches; and the Midi Trak-Ball are tested. When each switch is activatted, the location of that switch appears on the display. In Figure 10 all switches are activated. When the left JUMP switch is pressed, the motion-object_ pictures change from one group to another. When the right JUMP switch is pressed, the motion-object pictures change within that group of pictures. The Midi Trak-Ball is tested by rotating the ball vertically and horizontally. The hexadecimal number by the words HOR and VERT increase from 00 through FE, or decrease from FF through 00, as the ball is rotated. Likewise, the numbers beside the words GREEN and BLUE increase from 0 to 7. The GREEN numbers increase or decrease with a horizontal motion of the Midi Trak-Ball. The BLUE numbers increase or decrease with a vertical movement of the control. Also, the colors of the color bar at the bottom of the display change shades of green when the ball is rotated horizontally and shades of blue when moved vertically.
SuITEN TEST
zume guTToON orn BUTTON wert RIGHT Cert PIGHT AUX TRREK@RLL TEST mow op Vert 4B GREEN 2 uO rc
Figure 10 Switch Test Video Display
Reset Hall-of-Fame When you select this from the main menu, the entire hall-of-fame table is reset to initials and scores that are within the program memory. The scores in this table range from 27,000 to 30,000 points. We suggest you reset these after any changes are made to the options that may affect the average game time.
AL ATARI © Avie: conmuncabons Company