Badlands Universal Kit TM-344 2rd Printing
Bad Lands (Atari Games, 1989) · Technical Manual · 54 pages · 62 sections · original scan
_ TM-344 =: 2nd printing==
Universal Kit
_Installation Instructions
KiT INSTALLATION INSTRUCTIONS
Copyright © 1989, 1990 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us, Anyone who purchases such copies risks forfeiting such a game.
Published by: Atari Games Corporation 675 Sycamore Drive Milpitas, California 95036-1110
Printed in the U.S.A 3/90
Produced by the Atari Games Technical Publications Department. Technical Writing: Rosalind Hutton Editing and Text Layout: Andrea Dencker Illustration and Design: Mary Ohanessian Sumner
Notice Regarding Non-Atari‘ Parts
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:
- Substitute non-Atari parts in the game. © Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
- All ground wires in the game are properly connected as shown in the game wiring diagram. ° The power cord is properly plugged into a grounded three-wire outlet. © On games provided with an Electromagnetic Interference (EMD ground cage, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Contents
1 Installation How to Use This Manual ... - 1-1 Equipment Requirements 1-2 Tools Required 1-2 Inspecting the Kit 1-2 Preparing the Cabinet for the Kit Installation Installing the Kit Parts ... 1-3 Testing After Power-Up 1-9 Setting the Coin and Game Options. 19 Game Play 1-9
2 Self-Test Entering and Exiting the Self-Test. 2-2 RAM and ROM Test Self-Test Menu ..... Statistics ..
Input Test... Playfield Stamp Test Motion Object Test Motion Object Picture Test Playfield and Convergence Pattern Test. Color Bars and Color Purity Test 2-6 2-7
Sound Test .... 2-8
- Maintenance and Troubleshooting Video Display .... 34 Steering Assembly 3-4 Pedal Assembly... . 3-4
4 Ilustrated Parts Lists See the list of illustrations and list of tables that follow.
5 Schematics See the list of illustrations that follows.
Glossary
Statistics Sheet
Illustrations
Figure 1-1 Assembling the Pedal... 1-2 Installing the Pedals on the Game. 1-3 Assembling the Control Panel. 1-4
Figure 2-1 2-2
2-4 2-5 2-6 2-7
2-9 2-10
2-11
2-12
Figure 3-1 Figure 4-1 4-2
Figure 5-1
5-2
Table 1-1 1-2
Table 2-1 2-2
2-4
2-8
Table 3-1 Badlands Kit Parts Installed in a Cabinet...
Self-Test Menu Screen Statistics Screen... Histogram Screen. Coin Options Screen . Game Options Screen Input Test Screen Playfield Stamp Test Screen Motion Object Test Screen... Motion Object Picture Test Screen ..... 2-7 Playfield and Convergence Pattern Test Screen... Color Bars and Color Purity Test Screen... Sound Test Screen . Pedal Installation Template ... Maintaining the Steering Assembly. Steering Assembh Badlands Game PCB Assembly . Badlands Games PCB Assembly Schematic Diagram (6 sheets)... Steering PCB Schematic Diagram, Faulty RAM and ROM Tables, and Badlands Memory Map .... i
Tables
Equipment Requirements... Kit Contents List... JAMMA Pin and Wire Connections..... 1-6 Summary of All Self-Test Screens . Bad RAM Locations ... Bad Upper or Lower ROM Location: Coin Option Settings . Game Option Settings Motion Object Test ..... Motion Object Picture Test Error Locations ... Faulty Sound RAM and ROM Locations ... 2-9 Troubleshooting Table .. severe BD Voltage Inputs and Test Points on the PCBs..... What ROM Problems Look Like Atari Video Connector Pin Assignments... Badlands Kit Parts List....... 3-4
iii
Safety Summary
The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.
ABOUT WARNINGS, CAUTIONS,
AND NOTES In Atari publications, notes, cautions and warnings have the following meaning:
Chapter 1
Installation
How to Use This Manual
This manual provides information troubleshooting and maintenance
for installing, testing, and trouble- procedures. ml Chapter 4 contains
shooting the Badlands™ kit. The illustrated parts lists. m Chapter 5
manual is divided into the followcontains the schematics for the
ing chapters: m Chapter 1 describes the installation Badlands game PCB and steering PCB. Also, at the end
procedure and the Badlands game play. m™ Chapter 2 of Chapter 1, is the template for installing the pedals
contains self-test procedures. ™ Chapter 3 contains on the cabinet.
Installation
Equipment Requirements Table 1-1 lists the equipment required in the cabinet into which you are installing the Badlands kit.
Table 1-1 Equipment Requirements
Equipment Specification. Color RGB monitor Separate positive horizontal and vertical syne or negative composite syne Horizontal mounting Horizontal frequency: 15.750 KHz Vertical frequency: 60 Hz ‘Video input: 1V to 3V peak-to-peak positive polarity Metal only: 8 Ohms 10 Watts 45 VDC or +12 VDC Three-conductor with ground +5 VDC + 0.25V @ 5.0 amps +12 VDC £ 0.5V @ 1.0 amp -5 VDC £0,5V @ 1.0 amp (Optional) Video Display
Control Panel Speaker Coin Mechanism Power Cord
Power Supply
Tools Required @ Three C-clamps ®@ Drill with 5/16-inch drill bit, 3/16-inch drill bit, and a 1 3/16-inch hole cutter (or a 1 3/16-inch chassis punch) Phillips screwdriver Flat-blade screwdriver
Socket set and ratchet 1/4-20 hex wrench Wire cutters and strippers Straight edge Squeegee m X-ACTO™ knife m Fast-ons (if you are installing a new JAMMA harness)
Inspecting the Kit Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the Badlands kit Table 1-2 Kit Contents List
Amount Description Part No.
| 1 | JAMMA Harness Assy. | -A046501-01 |
| 1 | Badlands Game’ PCB. | ‘A047193-01 |
| 1 | Steering Assy (assembled with JS | A047502-01 |
Harness Assy, part no. A047138-01)
| 2 | Pedal Assy | A047507-02 |
| 1 | Badlands Poster | 047106-02 |
| 1 | Black Metal Control Panel Cover | 047461-01 |
Plate
| 2 | Reinforcing Plate for Steering Assy | 047512-01 |
2 Pedal Mounting Bracket 047509-01
| 1 | ‘Attraction Shield | 047205-01 | |
| 1 | Attraction Film | 047464-01 | | |
| 1 | 19” Display Bezel | 047463-01 | | |
| 1 | Control Panel Decal | 047462-01 | |
| 2 | Side Panel Decal | 047106-01 | |
| 1 | Product LD. Label | 038158-01 | |
| 1 | FCC Compliance Label | 039450-01 | |
| 2 | Ferrite Split Bead | 141026-001 |
i
| 4 | Snap-Action Switch | 160044-001 | | |
| 14. | #10-24 Polymer Hex Lock Nut. | 177010-240 | |
| 16 | #1/4-20 Polymer Hex Lock Nut | 177010-244 | |
| 1 | Tie Wrap | 178032-002 | |
| 1 | 5/32 Tamper-proof Hex Key | 178126-002 | |
| 2 | Red Button Assy | 178237-001 | |
| 2 | Blue Button Assy | 178237-005 | |
| 4 | Nylon PCB Standoff | 178265-001 | |
| 4 | Star/Fire Identification Collar | 178283-001 |
4 #6 x 3/4-Inch-Long Pan-Head Screw 72-6612S
| 8 | #10-24 x 1/2-Inch-Long Pan-Head. | _72-1108F |
Screw
| 6 | #10 Flat Washer | 175014-1040 |
| 16 | 1/4 Flat Washer | 175014-1050 |
| 8 | #10 Internal Lock Washer | 75-050. |
6 #10-24 x 1-Inch-Long Black Carriage 75-5116B Bolt
| 8 | 1/4-20 x 1 1/4-Inch-Long Black | 75-5520B |
Carriage Bolt
| 1 | Badlands Universal Kit Installation | TM-344 |
Manual
serial number, part number and description of the missing or damaged parts, and date received.
Preparing the Cabinet for
the Kit Installation
- Turn off power to the game.
- Remove the following from the cabinet: H Old PCB(). m@ Game harness if it is not Japan Amusement Machinery Manufacturers Association (JAMMA)compatible. ™ Control panel decals, labels, and controls. @ Side decals, graphics and adhesive. If the cabinet sides are damaged, repair them before putting on the new decals. m Video display shield, display bezel, attraction shield, and marquee.
- Wipe down and vacuum the cabinet. Paint the cabinet, if required.
Installing the Kit Parts
The kit parts are shown installed on a cabinet in Figure 1-4.
Installing the Pedal To install the pedals, you need a copy of the pedal installation template at the end of this chapter and the following parts from the kit: ™ The pedals and pedal brackets m Eight #10-24 x 1/2-inch-long pan-head screws, internal lock washers, and lock nuts m Eight 1/4-20 x 1 1/2-inch-long carriage bolts, flat washers and lock nuts.
- Take a pedal apart by removing the set screws on. the sides of the hinge. Take out the hinge pin. Take the pedal top off.
- Use the #10-24 pan-head screws to attach pedal bottom to the bracket. (See Figure 1-1.) Install the lock washers and lock nuts. Put the ground wire lug between a lock washer and a lock nut on one of these screws.
- Put a drop of oil on the hinge pin. Reassemble the pedal. 4, Put the other pedal on its bracket.
- Cut the copy of the pedal installation template apart. Put the pieces on the the cabinet according to the dimensions shown in Figure 1-2 and on the template. ' Installation
Dfill the holes in the cabinet with a 5/16-inch drill bit.
- Feed the pedal harnesses through the center holes. Insert the 1 1/2-inch-long carriage bolts from the outside. Install the flat washers and lock nuts.
Installing the Control Panel
To set up the Badlands control panel you need the following parts from the kit: m Black metal cover plate Control panel decal Two red and two blue buttons Four start/fire button collars m Two steering assemblies ™ Two steering assembly mounting plates Six #10-24 x 1-inch-long carriage bolts, flat washers, and lock nuts ™ Six #1/4 flat washers and lock nuts.
- Lay the black metal cover plate over the bare control panel. Line up the two center button holes on the metal cover plate with the two center button holes on the control panel. Screw two buttons in the two center holes. See Figure 1-3. (If your control panel does not have the two center button holes in the correct position, just center the metal cover plate on the control panel.)
- Clamp the cover plate to the control panel with three C-clamps.
- Drill six mounting holes for the cover plate through the control panel using a 3/16-inch drill bit.
- Install enough of the carriage bolts and lock nuts in the mounting holes to hold the cover plate in place.
- Using the cover plate as a template, cut the holes for the outer buttons with the 1 3/16-inch hole cutter. Drill three mounting holes for each steering assembly using a 5/16-inch drill bit. You may also need to drill holes for the steering harnesses.
- Take the metal cover plate off the control panel. With the cover plate off, install the control panel
1-3
Installation Badlands Universal Kit
Set Screw (2 places)
Hinge Pin
#10 Lock Nut (4 places)
#10 Lock Washer (4 places)
T
Flat Washer Pedal Buttom (@ places)
1/4"-20 Lock Nut (4 places)
1/4"-20 Carriage Bolt (4 places)
#10-24 Pan-Hd Screw ) (4 places) | Pedal Bracket
Figure 1-1 Assembling the Pedal
Installation,
Use a 5/16" Drill Bit, 10 places
Figure 1-2 Installing the Pedals on the Game
decal on the control panel. Do not put the decal over the black cover plate,
- Now install the black cover plate on the control panel with the carriage bolts, flat washers, and lock nuts.
- Install each steering assembly with a mounting
plate on the underside of the control panel. Install the mounting plate so the steering assembly cannot be torn off the control panel. Put the 1/4-20 lock nuts and flat washers on the studs. Do not use a ratchet or an air gun to tighten the nuts. 10.
- Install the buttons with a plastic “Start/Fire” collar under each button. Put the blue buttons on the left and red buttons on the right.
Black Metal Cover Install the steering mounting plates under the control panel so the steering assemblies cannot be torn
Steering Assy Mounting Plate ; off the control panel.
(2places) Steering Carriage
Wheel Assy (places) (2 places) places)
Steering Assy Steering Assy Flat Mounting — Mounting Harness.
Washer Holes Holes Holes
(6 places) (places) (6 places) (2 places)
Control Panel eS o Decal Biue Button Assy Snap-Action Switch Start/Fire Collar 2 places)
Blue Red
Red Button Holes Button Holes
Figure 1-3 Assembling the Control Panel
1s
Installation
Table 1-3 JAMMA Wire Connections
Component Side Solder Side
| Signal | Note* Wire Color | Pin | Wire Color _Note* | Signal |
| +V RIN | A | BN | 1 | 4V RIN |
| 4V RIN | 1 | +V RIN | ||
| +5V | Cc. | 2 | a5V | |
| AV | D | 2 | 45V. | |
| -5V | E | OR | 3 | =5V |
| +12V. | Ee | Y | 4 | +12V. |
| Key | acs | Key. | ||
| COIN CIR 1 | Jd | V/W | 5 | COIN CER 2 |
| Not used | K- | Not used | ||
| Li | Ww | TP,17.- | SPKR- |
My AUDIO. GND.
| 6 | Pp | COMPSYNC | |||||
| VIDEO GND | 6 | BK | (414 | Rk | Not used | ||
| SELF-TEST | 7 | Ww | 15 | $ | Not used | ||
| Left Player | | | Right Player | |||||
| COIN 1 | 8 | BK/Y | 16° | =«+T | BK/OR | 9 | COIN 2 |
| FIRE/START 1 | 10 | W/BK | vy | OU | Y/BK | 10 | FIRE/START 2 |
| Spare | W/BN | 1 | OV | Y/BN | Spare | ||
| Spare | W/R | 19 | WwW | Y/R | Spare | ||
| Spare | W/OR | 20. | & | Y/OR | Spare | ||
| Spare | W/Y | 21 | CY | Y/W | Spare | ||
| FIRE/START 1 | 10 | W/GN | 22 | Zz | Y/GN | 11 | FIRE/START 2 |
| PEDAL 1 | 15 | W/BU. | 23 | 0a | Y/BU | 15 | PEDAL 2 |
| PEDAL 1 | 16 | W/V | 24 | bd | V/V | 16 | PEDAL 2 |
| STEERING D | 12 | W/GY | 25 | ¢ | Y/GY | 12 | STEERING D |
| STEERING C | 13 | Vv | 26 | d | GY/W | 13 | STEERING C. |
| GND. | 14 | BK/W | 276 | BK/W | 14 | GND | |
| GND | 14 | BK/w | BO | BRW | 14 | GND |
- Notes for this table are on page 1-7.
Installing and Connecting the Harness
- If your game does not already have a JAMMA harness, find the JAMMA hamess (part no. A046501-
- in the kit and install it.
- Using Table 1-3, JAMMA Pin and Wire Connections, for wiring information, connect the JAMMA harness to existing component harnessing. Use crimp splices or butt soldering.
- Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The Badlands kit requires +5V and +12V. If -5V is available, it should be used too. If -5V is not available, connect both wires to the 5 V RTN (GND) terminal on the power supply unless the power supply has 12V RTN. If it does, connect both wires to it.
Installation
Notes to Table 1-3 Jamma Wire Connections
TP Twisted pair.
- Connect four of the large BN wires to the 5V RIN (GND) terminal on the power supply unless the power supply has a 12V RTN. If you have a 12V RTN, connect one of the wires to the 12V RTN (GND) terminal. Three of the R wires go to the +5V terminal on the power supply. If the power supply has a +SENSE terminal, connect one of these three wires to the +SENSE instead of the +5V, The fourth wire goes to the red wires on the steering assemblies. NM
- Connect both wires to the -5V terminal of the power supply. (If -5V is not available, connect both wires to the 5 V RTN (GND) terminal on the power supply unless the power supply has 12V RTN. If it does, connect both wires to it. NOTE: If -5V is not used, the maximum power to the speaker is reduced by half.) Connect both wires to the +12V terminal of the power supply. (if your coin counter(s) require(s) 12V, you can use one of these two wires for the + side of the coin counter(s).) Connect to the negative side of the coin counter(s). If your counter(s) require 5V, splice into the red wire that brings +5V to the steering assemblies. See
ME
a Attach to the video display.
- Use this wire if you want an external self-test switch. The Badiands kit already has a self-test switch on the PCB. If you connect an external selftest switch, first make sure the switch on the PCB is switched off. Then connect this wire to the N.O. terminal on the external self-test switch. Connect the common terminal of the self-test switch to one of the BK/W wires (GND). j
- Connect to the N.O. terminal of the left coin switch. Connect the common terminal of the coin switch to one of the BK/W wires.
- Connect to the N.O. terminal of the right coin switch. Connect the common terminal of the coin switch to one of the BK/W wires.
- Connect to the N.O. terminals of the left Fire/Start switches. Connect the common terminals of the Switches to one of the BK/W wires.
- Connect to the N.O, terminals of the right Fire/Start switches. Connect the common terminals of the | switches to one of the BK/W wires. i
- Connect to the gray wire on the steering assembly.
- Connect to the white wire on the steering assembly.
- Connect one wire to the negative sense terminal of the power supply (if it exists). Connect the second wire to the common terminals of the coin switches. Connect the third wire to the common terminals of the control switches. Connect the fourth wire to the black wires on the steering assembly harness.
- Connect to the blue wire on the pedal.
- Connect to the violet wire on the pedal.
- Connect the brown wire to the plus terminal on the speaker and the white wire to the négative terminal on the speaker.
If your original game used other voltages, they are not needed. Tie off any unused wires on the power supply.
- There is more than one wire for each voltage. Use more than one wire for each voltage (connecting them as described in Table 1-3) so that you do not overload the edge connector and cause it to burn.
Connecting Video Display Wires
Connect the wires designated for the red, green and blue video guns along with the sync and ground wires, according to Table 1-3. Connecting Coin Door Wires
- Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3.
- Connect one side of the door lamps to one of the BK/W wires. Connect the other side of the door lamps to the R wire supplying +5V to the joysticks.
(Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both sides of the lamps to the terminals on the power supply.)
Connecting the Control Wires Connect the steering assembly harnesses and the button harnesses to the JAMMA harness according to the information in Table 1-3
Installation. Badlands Universal Kit
Attraction Shield
Display Bezel Attraction Film
Side Panel Decal
Display Shield
Volume Control
Self-Test Switch
Control Panel Decal BI Button Assy Snap Action Switch Start/Fire Collar
Red Self-Test Label
Button Assy Snap Action Switch ‘Start/Fire Collar Control panel in closed position Foot Pedal
Figure 1-4 Badlands Kit Parts Installed in a Cabinet
Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, both pedals, the control panel, the video display, and the power supply. This is a safety requirement for the players’ protection. This AC ground must be of #18 AWG wire or larger.
Checking the JAMMA Connections Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and -5 Volts on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game.
Installing the Badlands Printed-Circuit
Board 1, After you have checked the power on the JAMMA connector, above, install the Badlands game PCB in the cabinet. Use the nylon standoffs and four #6-32 screws in the kit.
- Connect the JAMMA connector to the PCB.
- Turn on the power to the game. Check that the game PCB functions. If a video picture is not present, see Chapter 3.
Installing the Display Bezel
Find the cardboard display bezel (part no. 047463-01). Measure the size of the existing display bezel and cut the new display bezel to size, if necessary.
Installing the Product ID and FCC Label Place the product ID label (part no. 038158-01) and FCC label (part no. 039450-01) on the back of the cabinet.
Installing the Side Panel Decals
Find the side panel decals. Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals as shown in Figure 1-4. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.
Installing the Attraction Assembly
Find the attraction shield and the attraction film. Using the existing shield as a template, cut the shield and film to size, if necessary. Install them on the cabinet as shown in Figure 1-4.
Testing After Power-Up
Use the self-test to check the operation of the game. Refer to Chapter 2 for information about the self-test. Installation
Perform the self-test when you first set up the game, each time you collect the money, or when you suspect game failure.
Setting the Coin and Game Options
The Badlands coin and game options are set in the self-test. See Chapter 2 for information about the option settings.
Game Play This section of the manual describes the theme of the Badlands game and the game play features.
Introduction It has been 50 years since the nuclear disaster. The sport of sprint racing is now a ruthless battle between armed cars. These races take place on tracks built in the ruins of the dangerous nuclear zone known only as the BADLANDS. This is sprint racing gone BAD! It’s all-out war on the track as players blast away at the drones (and each other) to finish first! Players shoot playfield targets for extra points and bonus missiles!
Game Play One or two players can race at any time with Badlands’ buy-in and game continuation features. If a player loses to one of the drone cars, the player can put in another coin to continue on to the next heat and retain any custom car options he has acquired. Each race has four laps. Players continue on to the next racing heat as long as they beat the drone car. Badlands has eight unique track layouts set in eight different animated backgrounds that react to player shots and crashes. These backgrounds change with the level of difficulty. The backgrounds are: ® = The City—watch out for falling power lines and the water tower that crashes, spilling water on the track that slows you down. ™ = The Desert—the mountain rumbles and falls onto the track.
™ The Freeway—make your own shortcuts through the diner and gas station.
m= The Volcano—lava spills down upon the track. m The Junkyard—power lines fall and old cars explode on impact. The Military Base—cannons fire and missiles explode.
1-9
Installation
™ The Prison Yard—Use the gates to make shortcuts and avoid the towers that fire upon you.
m The Refinery—be careful of creating oil spills. Players can add coins to quickly customize their car. Custom car options include: ™ Missiles to destroy other cars and walls to make short cuts. Tires to slide less around the turns.
Turbo to get up to speed faster. Speed for higher top speed. Shields to protect the car from shots, missiles and crashing.
Use a 8/16" Dnit Bi, 10 places
Pedal Installation Template
Chapter 2
Self-Test
The Badlands™ game tests itself you suspect game failure. The
and provides visual and audible self-test screens provide informa-
indications of the condition of the tion pertaining to the game cir-
game circuitry and controls. Self- cuits and controls. This chapter
test information is displayed on the screen and shows the screens in the self-test and explains each of
through the sound system. No additional equipment is the tests. The screens and explanations are arranged in
required. Perform the self-test when you first set up the order they appear in the self-test. Table 2-1 lists all
the game, each time you collect the money, and when the self-test screens and their purposes.
Self-Test
Table 2-1 Summary of the Self-Test Screens
Screen Use or Purpose
RAM Screen RAMs are tested only if the self-test switch is switched on first and then the power Switch is turned on. Appears only if a RAM is bad. ROM Screen ROMs are tested only if the self-test switch is switched on first and then the power Switch is turned on. Appears oply if a ROM is bad, Self-Test Menu Screen ‘Use to choose the self-test screen you want to see. Statistics Screen Displays game statistics. Histogram Screen Displays the game histogram.
Coin Options Screen Game Options Screen Input Test Screen Playfield Stamp Test Screen
Motion Object Screen Motion Object Picture Test Screen Playfield and Convergence Test Screens Violet Convergence Screen Green Convergence Screen Other Test Patterns
Color Bars and Purity Test Screen Cyan, Yellow and Magenta Test Screen Red Color Purity Screen Green Color Purity Screen Blue Color Purity Screen White Color Purity Screen Grey Color Purity Screen
Sound Test Screen Use to set and check the coin options settings. Use to set and check the game options settings. ‘Use to test the player controls. Use to see the game stamps.
Use to test the movement and color of game objects. Use to test the game objects in the ROMs. Use to check and adjust video display convergence of red, blue, and green. Use to check and adjust video display convergence of red to blue ‘Use to check and adjust video display convergence of red and blue to green. Used to check the video display. convergence
Use to check the dynamic range of the video display color circuits. Use to check the dynamic range of the video display color circuits. ‘Use to check the red color purity in the video display. ‘Use to check the green color purity in the video display. Use to check the blue color purity in the video display. Use to check the white color in the video display, Use to check the grey color in the video display.
Use to check the audio circuits; RAM, and ROM: Also use to check the coin mechanism operation.
Entering and Exiting the
To enter the self-test, turn on the self-test switch, located on the game PCB at 19B near the JAMMA connector. the test, the display advances to the self-test menu screen automatically.
Testing Game RAMs No message appears while the test is checking the RAMs. If the game has a bad RAM, you may see a message, or if the problem is severe, you may only see If you turn on the self-test switch after the power is turned on, the self-test skips the RAM and ROM test. To test the RAMs and ROMs, first turn on the self-test switch and then turn on the power.
Turn off the self-test switch to exit the self-test and return to the Attract Mode. However, if you want to reset the coin or game options, leave the options screen and then turn off the self-test switch. If you turn off the self-test switch while you are on the options screen, the settings will not change.
RAM and ROM Test
Test the RAMs and ROMs by turning on the self-test switch first, and then the power switch. If the power was on when you turn on the self-test switch the RAM and ROM test is skipped. If the RAMs and ROMs pass a colored screen. See Table 2-2 for the location of the bad RAM if you see a message. If the test finds no RAM errors, no message appears and the program goes to the ROM test after a 4-second delay. The RAM test continues to run until it passes. You can advance to the next RAM or ROM test by pressing the left player Start/Fire button.
Table 2-2 Bad RAM Locations
RAM Type Location Video Display
Characteristic
CPU/Video 22V. Background color is red and foreground is black. Color RAM.” 8K Black and yellow are the main colors.
Testing Game ROMs If the ROMs have no errors, the ROM test displays no messages and advances to the Statistics screen. If a ROM fails, a message is displayed. If the game has an error in the program ROM, then the error number is shown at the bottom of the screen. See Table 2-3 for the location of the bad ROM.
Table 2-3 Bad Upper or Lower Main ROM Locations
Error Address Location on Game PCB
00000 U=20F L=27F 20000 U=17F. L=24F
If you think you have a ROM error, but the screen shows no messages, see Table 3-3 for information about the locations of various ROM functions.
Depending on how bad the ROM error is, you may not be able to go to the self-test menu by pressing the left player Start/Fire button. If you have more than one ROM error, you must press the left player Start/Fire button several times to go to the self-test menu.
Self-Test Menu
Choose the screen you want to see from this menu, shown in Figure 2-1. Move through the menu by turning the left steering wheel. To choose a screen, press the left player Start/Fire button.
SELF-TEST TO SELECT: USE LEFT WHEEL TO EXECUTE: PRESS LEFT START.
GAME STATS AND HISTOGRAM COIN OPTIONS GAME OPTIONS INPUT TEST PLAYFIELD STAMP TEST MOTION OBJECT TEST MOTION OBJECT PICTURES PLAYFIELD PATTERN TESTS {CONVERGENCE PATTERN) COLORBARS AND PURITY TESTS SOUND TEST:
Figure 2-1 Self-Test Menu Screen
Statistics
The statistics screen is shown in Figure 2-2. The statistics information is accumulated either from the first time the game was turned on or from the last time the Self-Test
STATISTICS. LEFTCOINS : RIGHT COINS : CONTINUES == CONVERSIONS : OPLYR MINS = 41 PLYR MINS: 2PLYR MINS = SESSIONS TOTAL GAMES ERROR COUNT : TOTAL GAME TIME
AVG GAMES/SESSION TO EXIT: PRESS LEFT START 40 CLEAR STATISTICS: WHILE SPINNING A WHEEL PRESS RIGHT START OS CREATION DATE 21 NOV 89. eg PG CREATION DATE 01 JAN 70
Figure 2-2 Statistics Screen
statistics were reset. To reset the statistics information, spin either steering wheel and while the wheel is spinning, press the right player Start/Fire button. Enter the information on the statistics screen on a copy of the statistics page in the back of this manual.
The following information appears on the statistics screen:
m@ Left Coins shows the number of coins deposited in the left coin mechanism.
™ Right Coins shows the number of coins deposited in the right coin mechanism. ™ Continues shows the number of times players continued their games.
™ Conversions shows the number of times players converted credits to wrenches. (The Convert Credits to Wrenches game options setting must be set to yes.) ™@ 0 Plyr Mins shows the minutes of idle time. ™ 1 Plyr Mins shows the minutes played as a 1-player game. ™ 2 Plyr Mins shows the minutes played as a 2-player game. m@ Sessions shows the number of sessions played. One session is the game play starting at the left or right player position and play ending at that position, regardless of the number of coins or time played. @ Total Games shows the total number of games
- played. One “game” is the time between a player starting and that player losing to a drone car. ™ Error Count shows the number of EEROM errors that were detected. If this is any number other than zero, all of the statistics may be wrong. If you have errors counted regularly, replace the EEROM at
Self-Test
location 27J on the Game PCB.
m= Total Game Time shows the total time, in minutes, that the game has been played. ™ Total Credits shows the total number of credits deposited in both coin mechanisms. ™ Avg Time/Credit shows the average game time per credit, in seconds, for all players.
@ Avg Time/Game shows the average game time per game, in seconds, for all players. The coin mode does not affect this figure, nor do credits converted to wrenches.
™@ Avg Games/Session shows the average number of games played in a session. This indicates continued games. Press the left player Start/Fire button to go to the histogram screen.
Histogram
The histogram screen is shown in Figure 2-3. The histogram shows the average game time from 0 to 600 or more seconds. The histogram also provides a corresponding bar graph. Enter the information on the histogram screen on a copy of the statistics page in the back of this manual.
The game times information is accumulated either from the first time the game was turned on or from the last time the game times were reset. To reset the his-
‘HISTOGRAM 4 GAME TIME IN SECONDS.
70 EXOT: PRESS LEST START. TO CLEAR HISTOGRAM: WHILE SPINNING A WHEEL PRESS RIGHT START
Figure 2-3 Histogram Screen togram, spin either steering wheel and while the wheel is spinning, press the right player Start/Fire button.
Press the left player Start/Fire button to go to the selftest menu screen.
‘
Coin Options
The coin options screen is shown in Figure 2-4. The coin options screen indicates the current coin option settings and allows you to change those settings. The settings, with defaults, are shown in Table 2-4. To move through the options, turn the left wheel. The blue box around the option name indicates the option
COIN OPTIONS. {DEFAULTS IN GREEN) COIN MODE 4 COIN 1 CREDIT RIGHT MECH MULTIPLIER 1 COIN COUNTS AS 1 COIN LEFT MECH MULTIPLIER 1 COIN COUNTS AS 1 COIN BONUS ADDER NO BONUS ADDER
To change OPTION: use LEFT Wheel To change SETTING: use RIGHT Wheel ‘Yo SAVE and EXIT: press LEFT Start To ABORT: press RIGHT Start
Figure 2-4 Coin Options Screen
Table 2-4 Coin Options Settings
Options Available Settings
Coin Mode One Coin + ‘Two Coins Three Coins Four Coins : Right Mech Multiplier 1 Coin Counts as 1 Coin + 1 Coin Counts as 4 Coins 1 Coin Counts'as 5 Coins 1 Coin Counts as 6 Coins
1 Goin Counts as:1 Coin + 1 Coin Counts as 2 Coins
No Bonus Adder # 2 Coins Give 1 Extra Coin 4 Coins Give 1 Extra Coin 4 Coins Give 2 Extra Coins 5 Coins Give 1 Extra Coin 3 Coins Give 1 Extra Coin Free Play Left Mech Multiplier
Bonus Adder
+ Manufacturer's recommended settings
that can be changed. The default setting appears in green letters. To move through the settings, turn the right wheel. To save the settings and exit the screen, press the left Start/Fire button. To leave the screen without saving the settings, press the right Start/Fire button. ™ = Coin Mode is the number of coins required for one credit. Coin Mode should have a blue box around it when you enter this screen. m@ Right Mech Multiplier is the number of coins each coin counts as in the coin mechanisms. Left Mech Multiplier is the number of coins each coin counts as in the coin mechanisms. m Bonus Adder lets you choose bonus coins, no bonus, or free play. If you replace the EEROM at location 27J or if a hardware problem occurs, the coin options will change to the default (green) settings.
Game Options
The game options screen is shown in Figure 2-5. This screen indicates the current game option settings, and is used to reset the high score table and change the game option settings. Refer to Table 2-5 for the available settings and Atari Games’ recommended settings. To move through the options, turn the left wheel. The blue box around the option name indicates the option
GAME OPTIONS (DEFAULTS IN GREEN) RESTORE FACTORY OPTIONS ‘nD SPECIAL COST ‘no special cost DIFFICULTY LEVEL moderate CONVERT CREDITS TO WRENCHES yes. MUSIC IN ATTRACT MODE yes. CLEAR HIGH SCORE TABLE na VWMOREV ‘To change OPTIONS: use LEFT Wheel To change SETTING: use RIGHT Wheel To SAVE and EXIT: press LEFT Start Yo ABORT: press RIGHT Start
Figure 2-5 Game Options Screen Self-Test
Table 2-5 Game Options Settings
| Option Name | Available Settings | | |
| Restore Factory Options. | No #Yes | | |
| Special Cost | No Special Cost + | | |
Two Credits to Start; One to Continue |
| Difficulty Level | Easy | Moderate + | | |
| Hard | Hardest | | | |
| Convert Credits to Wrenches | Yes | =——-No | | |
| Music in Attract Mode | Yes + | No | |
| Clear High Score Table | ‘Yes | No+ | | |
| Auto High-Score-Table Reset | Yes + | No. | |
| Don't-Do-Drugs Screen | Yes + | No |
+ Manufacturer's recommended settings
that can be changed. The default setting appears in green letters. To move through the settings, turn the right wheel. To save the settings and exit the screen, press the left Start/Fire button. To leave the screen without saving the settings, press the right Start/Fire button. m@ Restore Factory Options lets you set all the game options to the factory options or lets you use your own settings. Make sure you set this to 70 to use your own chosen settings. ™ Special Cost lets you choose two credits to start and one to continue, or no special cost, which is one credit to start and one to continue. & Difficulty Level lets you choose the difficulty level of the Badlands game. ™ Convert Credits to Wrenches controls whether playefs may convert credits to wrenches. @ = = Music in Attract Mode lets you turn the music on or off in the attract mode. ™ Clear High Score Table resets the high score table if you select Yes. @ Auto High-Score-Table Reset automatically resets the high-score table after 2000 games if no player has achieved a high score in the last 200 games. ™ Don't Do Drugs lets you turn off or on the FBI symbol screen in the attract mode.
Self-Test
Input Test
The input test screen, shown in Figure 2-6, checks the player controls. The inputs that are checked are: ™ Switches and Lev/Edge are for Atari Games development. m™ Leta Values, Raw and Delta are the inputs for the steering wheels and the pedals. m Left Wheel Delta value increases from 01, as you turn the wheel clockwise. The faster you turn the wheel, the higher the delta number is. As you turn the wheel counterclockwise faster and faster, the value decreases from FF. ™ Right Wheel Delta value increases from 01, as you turn the wheel clockwise. The faster you turn the wheel, the higher the delta number is. As you turn the wheel counterclockwise faster and faster, the value decreases from FF. m Left Pedal Delta value increases when you press the left pedal. ™ Right Pedal Delta value increases when you press the right pedal. m Self-Test should have a pink box around it when this screen appears. ™ VBLANK is for Atari Games development. & Right Start/Fire tests the right Fire/Start buttons. Press either of the right buttons and a pink box appears around the words. @ Left Start/Fire tests the left Fire/Start buttons. Press either of the left buttons and a pink box appears around the words. m Freeze, Freeze-Step, Old Gas Pedals, and Old Steering Wheels should never be highlighted. Simultaneously press the right and left player Start/Fire
INPUT TEST SWITCHES.
RAW LETA VALUES
aD. DELTA 00 Lett Wheel 90 Right Wheel fel Left Pedal LEV/EDGE 82 00 Right Pedal
NK RIGHT START/FIRE LEFT START/FIRE FREEZE FREEZE-STEP OLD GAS PEDALS OLD STEERING WHEELS.
TO EXIT: PRESS BOTH START BUTTONS
Figure 2-6 Input Test Screen
2-6 button fo return to the self-test menu screen.
Playfield Stamp Test
This screen shows the different stamps used in the game and appears in Figure 2-7. If you turn the left wheel clockwise, you will see Bank 0 stamps. If you turn the left wheel counterclockwise, you will see Bank 1 stamps. Simultaneously press the right and left player Start/Fire button to return to the self-test menu screen.
Motion Object Test
The motion object test screen is shown in Figure 2-8. The motion object test indicates the condition of the motion-object buffer circuit. Use the controls to test the motion objects as described in Table 2-6. Table 2-6 Motion Object Test
Control Function,
Right Start/Fire Displays a different set of patterns. Press this button to view the stamps from 0 to:C00. Left Wheel Turning the wheel moves the vertical. position of object. Right Wheel Turning the wheel moves the horizontal position of object. ee Left Start/Fire Pressing this button increases the selected object number. Left Pedal Pressing the pedal increases the palette of the selected object. (The priority changes every eighth palette.) Right Pedal Pressing the pedal increases the vertical size of the selected object.
Motion objects with priority 0 (PRI: 0) move behind the orange and grey vertical stripes on the sides of the screen. Motion objects with priority 1 move in front of the stripes. The following information is provided at the bottom of the screen: @ MOB indicates the number of the motion object selected. ™ PIX indicates the stamp number in ROM. HPOS indicates the horizontal position of the object. ® = VPOS indicates the vertical position of the object. m VSIZ indicate the number of stamps. PAL indicates the palette number for colors. PRI indicates priority. Simultaneously press the left and right Start/Fire buttons to return to the self-test menu screen.
Figure 2-8 Motion Object Test Screen
Motion Object Picture Test
The motion object picture test checks the information in the EPROMs in the game and is shown in Figure 2-
- Press the right Fire/Start button to see the next picture and press the left Fire/Start button to see the previous picture, To change the palette, press a pedal.
Table 2-7 Motion Object Picture Test Error Locations
Picture Number EPROM Location on Game PCB 0-3FF 14k 400-7FF 10R 800-BFF 14 Self-Test
WET Toe CR.
i
Pix: 0010 4 nag} tte ter next wigtyre: Hees +A : ae GE eee. gL Setey Beis SL So: SERS Os TH Figure 2-9 Motion Object Picture Test Screen.
View the pictures, and if you think there are errors (other than unusual colors) check the EPROMs as shown in Table 2-7. Simultaneously press the left and right Start/Fire buttons to return to the self-test menu screen.
Playfield and Convergence
Pattern Test
The first playfield and convergence pattern screen is shown in Figure 2-10. This test indicates the condition of the display size, centering, linearity, and convergence. The grid pattern should be white. Press the right player Start/Fire button and the grid pattern changes to violet. Pressing the right player Start/Fire button again should cause the grid pattern to turn green. Check ihe grid pattern for the following characteristics (the violet and white patterns are used
Ye TH ca & Figure 2-10 Playfield and Convergence Pattern Test Screen
Self-Test
to adjust the display convergence): @ Grid lines should show no pincushioning or barreling, and the lines should be straight within 3.0 mm. ™ Violet and white pattern convergence should be within 2.0 mm. If the display characteristics are not within these limits, refer to the display manual for the linearity and convergence adjustment procedures or to determine the possible cause of failure. If you press the left player Start/Fire button you will see a variety of patterns. Simultaneously press the left and right Start/Fire buttons to return to the self-test menu screen.
Color Bars and
Color Purity Test
The color bars and color purity test screen is shown in Figure 2-11. This test indicates the condition of the display color circuits.
Figure 2-11 Color Bars Test Screen
The screen should show, from top to bottom, a row of red, a row of green, a row of blue and a row of grey, each with 32 vertical bars. The brightest bars should be on the left and darkest (black) on the right, with a grey frame around the screen. If the display characteristics are not correct, refer to the video display manual for the color-gun adjustment procedure or to determine the possible cause of failure. If you press the right player Start/Fire button, you will see a screen with color bars of yellow, cyan, magenta, and grey.
Press the right player Start/Fire button again to see the color purity screens of red, green, blue, white and grey. These screens show the adjustment of the color purity of the video display. Each screen should display a rectangle of color, with no curving at the corners, no unevenness of color, and no lines in the display. If the screens are not correct, adjust the video display as described in the video display manual. Simultaneously press the left and right Start/Fire buttons to return to the self-test menu screen.
Sound Test
The sound test screen is shown in Figure 2-12. This test indicates the condition of the coin mechanisms and the music and sound-effects circuits.
SOUND TEST
SOUND 4 MUSIC CHIP TEST
NUMBER OF SOUNDS :. 73. SOUND CPU STATUS scoop COIN MECH SWITCHES: LEFT oO RIGHT oO
TO SELECT SOUND: USE RIGHT WHEEL TO PLAY: RHT START, TO STOP: LEFT. START TO EXIT: PRESS BOTH START BUTTONS
Figure 2-12 Sound Test Screen
The sound microprocessor is reset at the beginning of this test. The game may take up to three seconds to produce the first sound. If the sound-microprocessor reset fails, the message SOUND PROCESSOR NOT RESPONDING should blink. If the sound microprocessor is good, check the coin mechanisms and the sound microprocessor circuits by observing the following messages: ™ 1,2,3,4, etc. are the numbers assigned to each sound. Choose a sound by turning the right wheel Some sounds numbers cannot be selected. To hear the sound, press the left player right Start/Fire button one or more times. Press the left player Start/Fire button to silence the sound. m@ 4 Music Chip Test consists of eight tones in a major scale that alternate between sound channels (16 tones in all). = = Number of Sounds indicate the number of sounds used in the Badlands game.
Self-Test
Table 2-8 Faulty Sound RAM and ROM Locations
Error Message Location on Game PCB or Cause Music Chip Time Out 9D Sound CPU Interrupt Error 14, 175 Sound CPU RAM 1 Error OB
Sound CPU ROM 1 Error
9C If the message appears when you enter the test, then sound processor cannot run further. Press both Start/Fire buttons to return to the Self-Test menu. Communications Error #1 Sound Processor Not Responding Counts the number of errors caused by audio part of the game PCB. A major problem with the audio section of the game PCB.
™ Sound CPU Status indicates the condition of the sound microprocessor. If the sound microprocessor is good, the word GOOD should appear. If the sound microprocessor or associated circuitry is faulty, a number will appear (to indicate sound status) as well as an error message. See Table 2-7 for the error messages and faulty sound RAM and ROM locations. ™ Coin Mech Switches shows the condition of the left and right coin mechanisms. The zeroes underneath left and right correspond to the left and right coin mechanisms. The zero should change to one when the coin switch is held down, and change back to zero when it is released. Simultaneously press the left and right Start/Fire buttons to return to the self-test menu screen.
Chapter 3
Troubleshooting and Maintenance
This chapter contains regular
maintenance information, trou-
bleshooting tables, and repair
procedures for your Badlands
game. The chapter has two parts.
The first part contains three trou-
bleshooting tables. The first table has general trouble-
shooting information, the second contains the voltage
levels and test points on the PCBs, and the last table is ’ of ROM-caused problems with
specific ROMs to check and
replace. The last part of the chap-
ter has information about con-
necting the video display to the
Badlands kit and repair informa-
tion for the steering assembly and the pedal assembly.
If a part is mentioned, but not illustrated, see Chapter
4, Mustrated Parts Lists, for information.
Troubleshooting and Maintenance
Table 3-1 Troubleshooting Table
‘Wheel sticks or binds.
Wheel turns, but there is no response on the screen. Pedal Problems Pedal sticks.
‘No response on screen. when the pedal is pressed.
Sound Problems
Erratic sound Video Display Problems Sync Problems
Screen is Dark Coin Mechanism Problems 1, Test the coin mechanisms with the sound test screen in the self-test. : 2, Is the voltage to the + side of the mechanism correct? 3, Is the hamess to the coin mecHanism connected properly and in good condition? Game Play Problems _ 1. Perform the self-test. - :
- Are the harness and connectors good? Are the connectors firmly plugged in?
- Are the voltage levels on the PCB cortect? See Table 3-2, Voltage Inputs and Test Points.
- If you think you have a ROM problem, check Table 3-3, What ROM Problems Look Ltke. Steering Problems :
- The steering assembly may be bolted too tightly to the control panel. The nuts should not be tighter than 40 inch-pounds. Loosen the nuts slightly that hold the assembly on the control panel. e :
- If you have replaced the steering PCB, does the encoder wheel on the shaft fit between the sensors on the PCB?
- Is the steering harness firmly plugged in at-both ends?
- Does the steering PCB need to be repaired or replaced?
- Are there any obstructions?
- Does the hinge pin’need oil ? (This is very unlikely.)
- Are the harness connections good?
- Does the pedal assembly need to be replaced?
|. Is the speaker volume turned up? . Is the voltage on the JAMMA connector correct? . Is the harness from the PCB to the speaker connected and in good condition? . Is the audio ROM and RAM good? a. Check the ROM and RAM in the self-test on the Sound Test screen. See Table 2-4, Bad Sound RAM and ROM Locations. b. Check the ROM at 9C. SON
5, Is the the voltage level to the PCB correct? See Table 3-2, Voltage Inputs and Test Points. |
- Does the speaker need to be replaced? Is the audio ROM at 9C good?
Does your display need separate positive sync? See the Video Display Sync Problems section in this chapter. Is the game plugged in? . Is the game turned on? . Aré the connections good? Is the line fuse good? . Is the display brightness turned up? Are the solder connections on the line filter and transformer good? Is the JAMMA connector on the PCB tightly? Check all of the items below. If you answer no to any question, you have a problem with the video display, not with the game circuitry, See your video display service manual. a. Do you have power to the video display? b. Are the video display’s filaments lit? c¢. Do you have high voltage to the video display?
- Is the voltage level to the video display PCB correct? (Power voltage is 100 VAC or 110 VAC, depending on the type of video display. Video signal voltage is 0.5 to 3.5 Volts.) If the level is not correct, check the connectors and the harness, SIAVAWN
continued on page 3-3
Badlands Universal Kit Troubleshooting and Maintenance
Table 3-1 Troubleshooting Table, Continued
Problem Suggested Action
Video Display Problems | Display area wavers or is too 1. Do you have voltage to the video display PCB?
small. 2. Do you have high voltage to the video display?
Picture is wavy. 1, Is the monitor ground connected to the monitor?
- Are the sync inputs connected: properly? Does your monitor need a separate positive sync? See the Video Display Sync Problems section in this chapter. Picture is upside down, Switch the horizontal or vertical yoke wires on the display. Convergence, purity Use the screens in the self-test to adjust the video display. or color problems
Table 3-2 Voltage Inputs and Test Points on the PCBs
‘Voltage Test Point or LED. Source and Purpose
| +5 £0.25 VDC | +5V1 | Logic power from the switching power supply. |
CR} LED Lights when 5 V is applied to the main PCB and the reset (RST) jumper is open. ‘CRG LED Lights when the +12 V supply is good, CR] LED Lights when the -5 V supply is good.
| eke | -VOP | Negative supply for the audio analog circuitry from the switching power supply. |
(pin 11 of any 1M324)
| #12 | +VOP | Positive supply for the audio analog circuitry from the switching power supply. |
(pin 4 of any LM324).
Table 3-3 What ROM Problems Look Like
| Problem | ROM Causing | Check the ROM at: |
the Problem.
| Program works and the playfield looks OK, but the motion | Motion object | 1OR, 14K, 147 |
objects are wrong,
| Program works, motion objects look OK, but the playfield is wrong. | Playfield | 2N, 28, 2U, 4N, 48, 4U |
| Garbage on screen; program doesn't work. | Processor | 226 |
Program ROM 17F, 208, 24F, 27F
| Game program is erratic. | Program ROM | = | ATF, 20F, 24F, 27F |
No sound or erratic sound: Audio ROM 9C
‘Troubleshooting and Maintenance
Video Display
Sync Problems Some video displays cannot use the composite negative sync that is on the JAMMA connector. If you need separate positive sync the Badlands game PCB includes a standard Atari video connector (located at 14A) that provides separate positive sync. Refer to Table 3-4 and make the appropriate connections for your video display. Table 3-4 Atari Video Connector Pin Assignments for Separate Positive Sync
Red : ee :
Key (no connection required) / Green os : _ GND Blue GND. GND . : Negative composite sync
- Positive V sync woe WANA Ne
i Positive H syne
Horizontal Shifting If you cannot center the display horizontally as described in your video display manual, you can shift it horizontally by altering the game PCB.
- Remove the resistor at R98.
- To shift the display to the right, add a resistor of less than 100 Q (or a wire) at location R99. To shift the display to the left, add a resistor of less than 100 Q (or a wire) at location R100.
Steering Assembly
Replacing the Steering Wheel
It is easier to replace the steering wheel if you remove the steering assembly from the control panel.
- Open the control panel.
- Unscrew the nuts that hold the steering assembly on the control panel. Remove the reinforcing plate.
- Take off the connector to the PCB. Remove the steering assembly from the cabinet. 4, The screws that hold the steering wheel on the steering assembly are tightened to 90 inch-pounds, and are difficult to remove. One way to loosen the screws is to put the tamper-proof hex key in a vise, put the screw head into the key, and turn the steering wheel until the screw is loosened. Loosen and remove all the screws.
- Replace the steering wheel. Replace the screws. Tighten to 90 inch-pounds.
- Install the steering assembly on the control panel. «Install the nuts on the studs. Tighten these nuts to 40 inch-pounds maximum. If you tighten the nuts too much, you can damage the steering assembly and the steering wheel will not turn easily.
Replacing the Steering PCB The steering wheel assembly is shown in Figure 3-1.
- Open the control panel.
- Unscrew the nuts that hold the steering assembly on the control panel. Remove the reinforcing plate.
- Take off the connector to the PCB. Remove the steering assembly. 4, Remove the two cross-recessed screws that hold the PCB bracket on the steering housing. Remove the bracket and the PCB.
- Take the old PCB off the bracket. Repair or replace jt. (The schematic for the PCB is in Chapter 5 of this manual.) Install the repaired or new PCB on the bracket.
- Put the PCB and the bracket into the steering housing. Make sure the encoder wheel, inside the housing, fits between the two parts of the sensor on the board and does not scrape against the sensor.
- Put the screws and the washers into the PCB and attach the PCB to the housing.
- Install the steering assembly on the control panel. Install the nuts on the studs. Tighten these nuts to 40 inch-pounds maximum. If you tighten the nuts too much, you can damage the steering assembly and the steering wheel will not turn easily.
Pedal Assembly
The only parts of the pedal assembly you can replace separately are the set screws on the hinge (part number 75-4504) and the pedal tread (part number 047518- 01). You must purchase the rest of the pedal as an assembly because special techniques are required to assemble it at the factory.
72-1605S 78-40104 6-32 Pan-Hd Screw Steering Wheel (2 places)
1475014-1026 A047368-01 138000-001 #6 Flat Washer P.C. Board Opto-Sensor (2 places) Assy
176025-4412 114-20 Button-Head ‘Tamper Proof Screw 75-0558 1/4 Internal Lock-Washer
(046655-01 Cover Plate 79-58356 Connector
110027-151 150Q, 1/8 W Resistor
047504-01 Set onrgteon
75-4006 047513-01 Set Screw Encoder Wheel 75-0448 Split Lock Washer 72-8406 #4-40 Screw
175014-1018 #4 Flat Washer ‘Troubleshooting and Maintenance
72-1605S 6-32 Pan-Hd Screw
175014-1026 047503-01 #6 Flat Washer Housing
047505-01 PCB Bracket
178012-001 Clip Ring 047508-01 Shim
Figure 3-1 Maintaining the Steering Assembly
3-5
Chapter 4
Illustrated Parts
This chapter provides information
you need to order parts for your
game. Common hardware parts,
such as screws, nuts, washers, and so on usually are
not listed in the parts lists. The parts lists (except for
the PCB parts lists) are arranged alphanumerically by
Atari part number. All A-prefix numbers, which are
assemblies, come first. Next are part numbers with six
numbers followed by a hyphen (000598- through
201000-). Ending the list are part numbers with a two-
number designation followed by a hyphen (00-
Lists
through 99-). The PCB parts lists
are arranged in alphabetical order
by component. Within each sec-
tion the parts are arranged numerically by part num-
ber. When you order parts, give the part number, part
name, the number of this manual, and the serial
number of your game. With this information, we can
fill your order rapidly and correctly. We hope this will
create less downtime and more profit from your
games. Atari Games Customer Service phone numbers
are listed on the inside front cover of this ma:tual.
Illustrated Parts Lists
Table 4-1 Badlands Kit Parts List A047460-01 C
| Part No. | Description | Part No. | Description |
| A047193-01 | Badlands Game PCB Assembly | ,141026-001 | Ferrite Split Bead |
| A046501-01 | JAMMA Harness Assembly | 160044-001 | Snap-Action Microswitch |
| A047502-01 | Steering Assembly (assembled at the factory | 177010-240 | —-#10-24 Polymer Hex Locknut |
| with JS Hamess Assembly part no. | 177010-244 | #1/4-20 Polymer Hex Locknut |
A047138-01)
| A047507-02 | Pedal Assembly. Replaceable Parts: | 178032-002 | Wire Tie Wrap |
| 75-4504 | 1/4-20 x 1/4-Inch Long Hex Socket Set | 178126-002 | 5/32 Tamperproof Hex Key |
| Screw | 178237-001 | Red Button Assembly | |
| 047518-01 | Pedal Tread | 178237-005 | Blue Button Assembly |
| 047461-01 | Black Metal Control Panel Cover Plate | 178265-001 | Nylon PCB Standoff |
| 047512-01 | Reinforcing Plate for Steering Assembly | 178283-001 | _Start/Fire Identification Collar |
| 047509-01 | Pedal Mounting Bracket | 72-6128 | #6-32 x 3/4-Inch Pan-Head Screw |
| 047205-01 | Attraction Shield | 72-1108F | #10-24 x 1/2-Inch-Long Pan-Head Screw |
| 047464-01 | Attraction Film | 175014-1040 | #10 Flat Washer |
| 047463-01 | 19” Display Bezel | 175014-1050 | 1/4 Flat Washer |
| 047462-01 | Control Panel Decal | 75-050 | #10 Internal Lock Washer |
| 047106-02 | Badlands Poster | 75-5116B | #10-24 x 1-Inch-Long Black Carriage Bolt |
| 047106-01 | Side Panel Decal | 75-5520B | 1/4-20 x 1 1/4-Inch-Long Black Carriage |
| 038158-01 | Product LD. Label | Bolt | |
| 039450-01 | FCC Compliance Label | TM-344 | Badlands Universal Kit Installation Manual |
4-2
72-6058 78-40104 Steering Wheel 6-32 Grae ae 175014-1026 A047368-01 #6 Flat Washer P.C. Board (2 places) Assy 138000-001 ‘Opto-Sensor
176025-4412 1/4-20 Button-Head Tamper Proof Screw _ _75-055B 1/4 Internal Lock-Washer
046655-01 Cover Plate 79-58356 Connector
047514-01 Illustrated Parts Lists
72-1605S 6-32 Pan-Hd Screw 175014-1026 047503-01 #6 Flat Washer Housing
S yy
Hub 178012-001 30 75-4006 Clip Ring 047513-01 Set Ser EneoderWheel onmenon 75-0448 Split Lock Washer 72-8406 #4-40 Screw 17504-1018 #4 Flat Washer
Figure 4-1 Steering Assembly A047502-01 B
Steering Assembly Parts List
| Part No. | Description | Part No. | Description |
| A047367-01 | _P.C. Board Assembly. Replaceable Parts: | 176025-4412 | _1/4-20 x 3/4-Inch-Long Tamper-Proof |
| 110027-151 | 150Q, 1/8 W Resistor | Button-Head Screw | |
| 138000-001 | Opto-Sensor | 178012-001 | 3/4-Inch Diameter Klip Ring |
| 79-58356 | Connector | 72-1605S | #6-32 x 5/16-Inch-Long Pan-Head Screw |
72-8406 #4-40 x 3/8-Inch-Long Cap Screw 046655-01 Cover Plate
| 047503-01 | Steering Housing | 175014-1018 | #4 Flat Washer | |
| 047504-01 | Steering Shaft | 175014-1026 | #6 Flat Washer | |
| 047505-01 | Steering Bracket | ‘ | 75-044 | #4 Split Lock Washer |
75-055B 1/4 Black Internal Lock Washer 047508-01 3/4-Inch Shaft Spacer Shim
| 047513-01 | Encoder Wheel | 75-4006 | #10-32 x 3/8-Inch-Long Set Screw |
| 047514-01 | Encoder Hub | 78-40104 | Steering Wheel |
4-3
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Illustrated Parts Lists
Badlands Game PCB Assembly Parts List
| Designation | Description | Part No. | Designation | Description | Part No. |
Integrated Circuits
| 1K | Integrated Circuit, 74HCT273 | 137655-001 | 16C | Integrated Circuit, 7415240 | 137251-001 |
| 2E | Integrated Circuit, LM324 | 137582-001 | 16P | Integrated Circuit, 74FOO | 137327-001 |
| 2 | Integrated Circuit, 74F260 | 137570-001 | 16S | Integrated Circuit, GAL16V8 | 136074-1003 |
| 2N | Integrated Circuit, OTP, 250 nsec | 36074-1013 | 17F | Integrated Circuit, EPROM, 250 nsec 136074-1009 | |
| 2s | Integrated Circuit, OTP, 250 nsec | 36074-1015 | 17 | Integrated Circuit, 74F32 | 137486-001 |
| 2U | Integrated Circuit, OTP, 250 nsec | 136074-1017 | 17K | Integrated Circuit, 74LS175 | 137123-001 |
| 3K | Integrated Circuit, 7418374 | 137144-001 | 17U | Integrated Circuit, VMATCH | 137552-001 |
| 4 | Integrated Circuit, 74F260 | 137570-001 | 18C | Integrated Circuit, 7418244 | 137038-001 |
| 4N | Integrated Circuit, OTP, 250 nsec | —_-136074-1012 | 18R, 18S Integrated Circuit, 74F74 | 137436-001 | |
| 48 | Integrated Circuit, OTP, 250 nsec | 36074-1014 | 19 | Integrated Circuit, 741808 | 137012-001 |
| 4U | Integrated Circuit, OTP, 250 nsec | —_-136074-1016 | 19K | Integrated Circuit, 7415240 | 137251-001 |
| SE | Integrated Circuit, LM324 | 137582-001 | 19N | Integrated Circuit, 7418374 | 137144-001 |
| 5K | Integrated Circuit, 74HCT273 | 137655-001 | 20C | Integrated Circuit, LETA | 137304-2002 |
| OF | Integrated Circuit, 7406 | 137052-001 | 20F | Integrated Circuit, EPROM, 250 nsec 136074-1008 | |
| 7N | Integrated Circuit, 7418374 | 137144-001 | 21R | Integrated Circuit, GALIGV8 | 136074-1002 |
| 7R,7T | Integrated Circuit, 74F374 | 137420-001 | 21T | Integrated Circuit, 74F157 | 137494-001 |
| WV | Integrated Circuit, 7418374 | 137144-001 | 22E | Integrated Circuit, 68000, 8 MHz, | —137289-003 |
| 8E | Integrated Circuit, YM3012 | 137402-001 | PLAS, | ||
| 8F | Integrated Circuit, 7418245 | 137134-001 | 225 | Integrated Circuit, 74F74 | 137436-001 |
| 8 | Integrated Circuit, 74F0O | 137327-001 | 22K | Integrated Circuit, 7418374 | 137144-001 |
| 22N | Integrated Circuit, 7418257 | 137136-001 | |||
| 8K | Integrated Circuit, RAM, 2K x | 137534-001 | |||
| 8, 35 nsec | 22v | Integrated Circuit, RAM, 8KX8, | 137535-004 | ||
| 9B | Integrated Circuit, RAM, 8K x 8, | 137535-005, | 100 ns | ||
| 120 nsec | 23R | Integrated Circuit, 74F74 | 137436-001 | ||
| 9c | Integrated Circuit, OTP, 250 nsec | 1360741018 | 23 | Integrated Circuit, 74F157 | 137494-001 |
| 9D | Integrated Circuit, YM2151 | 137401-001 | 24C | Integrated Circuit, 7418138 | 137177-001 |
| ON | Integrated Circuit, GALIGV8 | 136074-1004 | 24F | Integrated Circuit, EPROM, 250 nsec 136074-1007 | |
| ov | Integrated Circuit, 7418374 | 137144-001 | 24 | Integrated Circuit, 74F20 | 137530-001 |
| 10E | Integrated Circuit, 74LS174 | 137122-001 | 25M. | Integrated Circuit, SOS | 137550-001 |
| 10F | Integrated Circuit, 741138 | 137177-001 | 264 | Integrated Circuit, LM556, Dual | 137660-001 |
Timer
| 10) | Integrated Circuit, 74F04 | 137437-001 | |||
| 10K | Integrated Circuit, 74F374 | 137420-001 | 26C | Integrated Circuit, GALIGV8 | 136074-1001 |
| 10R | Integrated Circuit, OTP, 250 nsec | 36074-1011 | 26R | Integrated Circuit, GALI6V8 | 136074-2000 |
| uv | Integrated Circuit, 7418175 | 137123-001 | 26T | Integrated Circuit, 74F153 | 137492-001 |
| 26U | Integrated Circuit, 74F04 | 137437-001 | |||
| 12E | Integrated Circuit, GAL16V8 | 136074-1005 | |||
| 13F | Integrated Circuit, 7418374 | 137144-001 | 27F | Integrated Circuit, EPROM, 250 nsec 136074-1006 | |
| 13) | Integrated Circuit, 74F0O | 137327-001 | ay | Integrated Circuit, EEPROM, | 137399-300 |
| 13V | Integrated Circuit, 74LS175 | 137123-001 | 2816 A, 300 ns | ||
| 28A | Integrated Circuit, 741S197 | 137240-001 | |||
| 14C | Integrated Circuit, 6502 A | 137577-001 | 28L | Integrated Circuit, 7418257 | 137136-001 |
| 14E | Integrated Circuit, 74F74 | 137436-001 | |||
| 14R | Integrated Circuit, OTP, 250 nsec | 36074-1010 | 28N | Integrated Circuit, 74F373 | 137575-001 |
| MT | Integrated Circuit, OTP 250 nsec | —_-136074-1019 | 28R | Integrated Circuit, 7418163 A | 137114-001 |
| 28T | Integrated Circuit, 74F153 | 137492-001 | |||
| 15F | Integrated Circuit, 7418374 | 137144-001 | Capacitors | ||
| 15) | Integrated Circuit, 74F74 | 137436-001 | C2 | Capacitor, 47 UF, 25 V, Electrolytic | 124009-476 |
| 15K | Integrated Circuit, 74F04 | 137437-001 | ron) | Capacitor, .1 UF, 50 V, Ceramic | 122002-104 |
| 15N | Integrated Circuit, LB | 137536-001 | C4 | Capacitor, 470 WF, 25 V, Electrolytic, 123003-477 | |
| 15V | Integrated Circuit, 74F74 | 137436-001 | Radial |
Illustrated Parts Lists Badlands Universal Kit
Badlands Game PCB Assembly Parts List, Continued
| Designation | Description | Part No. | Designation | Description | Part No. |
| C6-C9 | Capacitor, .1 UF, 50 V, Ceramic | 122002-104 | RIG-RI9 | Resistor, 3.3 K Q, 45%, 1/8 W | 110027-332 |
| C10-C15 | Capacitor, 100 pF, 100 V, Ceramic | 122016-101 | R22-R25_ | Resistor, 470 Q, +5%, 1/8 W | 110027-471 |
| €16-C24 | Capacitor, .1 HF, 50 V, Ceramic | 122002-104 | + - R26, R27_Resistor, 24 K Q, 45%, 1/8 W | 110027-243 | |
| €25-C28 | Capacitor, .001 UF, +10%, 50V | 122015-102 | R30 | Resistor, 100 K Q, 45%, 1/8 W | 110027-104 |
| €29-C32 | Capacitor, .01 WF, 50 V, Ceramic | 122002-103 | R31 | Resistor, 220 Q, 45%, 1/8 W | 110027-221 |
| 33 | Capacitor, .1 fF, 50 V, Ceramic | 122002-104 | R32-R35_ | Resistor, 1 K Q, 45%, 1/8 W | 110027-102 |
| 35 | Capacitor, 47 UF, 25 V, Electrolytic | —124009-476 | R37-R41_ | Resistor, 10 K Q, 45%, 1/8 W | 110027-103 |
| C36, C37 Capacitor, .1 WF, 50 V, Ceramic | 122002-104 | R42 | Resistor, 1 K Q, +5%, 1/8 W | 110027-102 | |
| 38 | Capacitor, 10 PF, 25 V, Electrolytic | 124009-106 | R43-R45__ | Resistor, 10 K Q, 45%, 1/8 W | 110027-103 |
| C39 | Capacitor, .001 HF, +10%, 50V | 122015-102 | R46-R56 | Resistor, 1 K Q, 45%, 1/8 W | 110027-102 |
| C40, C41 Capacitor, .1 UF, 50 V, Ceramic | 122015-104 | R57 | Resistor, 470 Q, +5%, 1/8 W | 110027-471 | |
| C42 | Capacitor, .001 HF, +10%, 50V | 122015-102 | R58-R6O | Resistor, 1 K Q, +5%, 1/8 W | 110027-102 |
| C43, C44 Capacitor, .1 HF, 50 V, Ceramic | 122002-104 | ROL | Resistor, 5.1 K Q, 45%, 1/8 W | 110027-512 | |
| C45 | Capacitor, 47 pF, 25 V, Electrolytic | —124009-476 | R62 | Resistor, 12 K Q, 45%, 1/8 W | 110027-123, |
| C46 | Capacitor, .1 WF, 50 V, Ceramic | 122002-104 | R63 | Resistor, 47 K Q, $5%, 1/8 W | 110027-473, |
| C7 | Capacitor, 22 WF, 35 V, Electrolytic | 124000-226 | R64 | Resistor, 12 K Q, 45%, 1/8 W | 110027-123 |
| C48 | Capacitor, .1 pF, 50 V, Ceramic | 122002-104 | R65 | Resistor, 1.5 K Q, 45%, 1/8 W | 110027-152 |
| c49 | Capacitor, .0022 HF, 50 V, Ceramic | 122015-222 | RO | Resistor, 1 K 2, 5%, 1/8 W | 110027-102 |
| 50 | Capacitor, .001 LF, £10%, 50V | 122015-102 | R67, ROS Resistor, 18 K Q, 45%, 1/8 W | 110027-183 | |
| C51, C52 Capacitor, .1 UF, 50 V, Ceramic | 122002-104 | ROO | Resistor, 560 2, $5%, 1/8 W | 110027-561 | |
| 53 | Capacitor, 22 HF, 50 V, Ceramic | 122017-224 | R70 | Resistor, 470 Q, 45%, 1/8 W | 110027-471 |
| C54, C55. Capacitor, .001 uF, £10%, 50V | 122015-102 | R71 | Resistor, 1.5 K Q, 25%, 1/8 W | 110027-152 | |
| C56, C57 Capacitor, .1 HF, 50 V, Ceramic | 122002-104 | R72 | Resistor, 100 2, £5%, 1/8 W | 110027-101 | |
| C58 | Capacitor, 10 UF, 25 V, Electrolytic | _124009-106 | R74 | Resistor, 2.4 K Q, $5%, 1/8 W | 110027-242 |
| C59, C60 Capacitor, 100 pF, 100 V, Ceramic | 122016-101 | RIS | Resistor, 15 Q, 45%, 1/8 W | 110027-150 | |
| €63-C116 Capacitor, .1 HF, 50 V, Ceramic | 122002-104 | R77 | Resistor, 10 ©, +5%, 1/8 W | 110027-100 | |
| Diodes | R78 | Resistor, 1.5 K Q, £5%, 1/8 W | 110027-152 | ||
| CRI, CR2 Diode, 1N4001 | 131048-001 | R81 | Resistor, 2.4 K Q, +5%, 1/8 W | 110027-242 | |
| CR3 | Diode, MV5053, Light Emitting | 131027-002 | |||
| CR4, CRS Diode, 1N4001 | 131048-001 | R82 | Resistor, 15 2, 5%, 1/8 W | 110027-150 | |
| CR6, CR7 Diode, MV5053, Light Emitting | 131027-002 | R83 | Resistor, 1.5 K Q, +5%, 1/8 W | 110027-152 | |
| R84 | Resistor, 10 Q, +5%, 1/8 W | 110027-100 | |||
| u | inductor, 100 _ | Teen | R85 | Resistor, 1002, +5%, 1/8 W | 110027-101 |
| Transistors | R86 | Resistor, 2.4 K Q, 45%, 1/8 W | 110027-242 | ||
| Q1-Q3 | Transistor, 2N5306 | 133033-001 | R88 | Resistor, 1.5 K Q, +5%, 1/8 W | 110027-152 |
| O4 | Integrated Circuit, TDA2030 | 137301-001 | R89 | Resistor, 15 Q, +5%, 1/8 W | 110027-150 |
| Q5-Q8 | Transistor, 2N3904 | 133041-001 | ROL | Resistor, 10 Q, £5%, 1/8 W | 110027-100 |
Resistors
| RI | Potentiometer, 10 K Q, Vert, with | 119020-103 | R92 | Resistor, 1002, 45%, 1/8 W | 110027-101 |
| Knob | R93-ROS | Resistor, 10 K Q, 45%, 1/8 W | 110027-103 | ||
| R2 | Resistor, 1002, +5%, 1/8 W | 110027-101 | R96, R97 Resistor, 1002, 45%, 1/8 W | 110027-101 | |
| R3 | Resistor, 18 K Q, +5%, 1/8 W | 110027-183 | ROB | Resistor, 10 Q, +5%, 1/8 W | 110027-100 |
| R4,R5 | Resistor, 1 K Q, 45%, 1/8 W | 110027-102 | |||
| R101 | Resistor, 1.5 K Q, 45%, 1/8 W | 110027-152 | |||
| R6 | Resistor, 0, +5%, 1/4 W | 110005-001 | R102 | Resistor, 3.3 K Q, 45%, 1/8 W | 110027-332 |
| R7-RO | Resistor, 220 Q, 45%, 1/8 W | 110027-221 | |||
| RIO-RI4 | Resistor, 1 K Q, 45%, 1/8 W | 110027-102 | RNI-RN3_ Resistor Network, R2R | 118016-001 | |
| RIS | Resistor, 10 Q, +5%, 1/8 W | 110027-100 |
4-6
Badlands Game PCB Assembly Parts List, Continued. Illustrated Parts Lists
Designation Description Part No. Designation Description Part No. Miscellaneous Socket, 28 Pin, .600” 179257-028
| Switch, Slide, SPDT | 160040-001 | Socket, 16 Pin, .300” | 179259-016 | |
| X1 | Crystal, 14.318 | 144000-004 | Socket, 24 Pin, .300” | 179259-024 |
| Connector, 11 Ckt, Header, .100 | 179118-011 | Socket, 20 Pin, .300” | 179259-020 |
Ctr, Key 3
| Connector, 2 Ckt, Header, .100 Ctr | 179048-002 | Socket, 40 Pin, .600” | 179257-040 |
Socket, 64 Pin, .900” 179256-064 Connector, 2 Ckt, Header, .100 Ctr 179048-002
4-7
This chapter contains the sche-
matics for your Badlands Univer-
sal Kit.™ The Badlands Game
PCB schematic has six pages and
is shown in ths chapter. (The as-
sembly drawing and parts list for
the game PCB are shown in Chapter 4, Ilustrated Chapter 5
Schematic Diagrams
About this Chapter...
Parts Lists.) The Steering PCB,
memory map and the faulty
RAM/ROM tables are also shown.
The part numbers for the steering
PCB are shown in the steering
assembly drawing in Chapter 4.
The Badlands game does not have an audio PCB.
‘Schematic Diagrams Badlands Universal Kit
JAM-A —
Rag 10K
osu.
sat-23
wee-24:
a,
/ TEST: 18C Twa i ef Thee Th = Ta t asia = tS Bie 508 Hla ~ yE ig 20 ssurtcnes a1 SELFTEst SW. Poly oS — /TEST sxo*
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
a
hs i n au 1 1 zr zr a ze z =
| a | a | az. | |
| Bs | et] | Hae | |
| 24 | Ez | ro | ote |
| a | 2 | yo | ty |
| $ | £ | Ho S ate ty ——Hlo ote | |
| $ | $ | el * Shar | a3] > Sia |
| = | cs | AOE | |
| 7 | zi | fy lhe | rl |
1H rr. /PFBENL- “erpey le PrALS. /PFALS. me
+ “} u So, lS 4H vrs sito < ofS “SIE ere . DS ofS al Prt > as * oor nw nh /CRAMAT 7CRAMAG 7CRAMAS 7CRAMAA 7CRAMAZ 7CRAMAZ 7CRAMAL
Figure 5-1 Badlands Game PCB Assembly Schematic Diagram, Sheet 3 of 6 04719401 C ‘Schematic Diagrams
Schematic Diagrams Badlands Universal Kit
jmoe at oe ma ov
| “M01. | 2 | 30 |
| z | ra | al |
| mon: | FeO perestH—® | ne |
7RsTH Fy me rs bd ASN ae ry a
| +5u: | A | 20 |
| 18S_Ai0F74 “Oo | RAMOZ—) | ORL |
Bp et oo ramos 44 4a ale 23) mv. 78H- “s RAMDO B +5u. 107
| , | 2 | . | |
| gemnis—2 fois | Ls = | ms | (8 |
| rampiatelore emus} 38 i——— | ay | +5V. |
Ramo1 3113 rate 3S . cai
| RaMo1222) m2 pana se | i | syiaizn |
RAMI 24x, rata} ar aus
| Remotoelo0 “eo | “ | eared | ||
| aro? 2 oy | ray | a | ||
| feros—¢ loo oes | stray | : | ||
| RAMO? “e107 | Rees | T | ~ Hit | re] |
| RAMDG-F06 | rast | it | Hjae oe 48. | 2 |
| ranos—tt1os Raa | a | Stas os}iz | a | |
| Ravod—22 oe | reap | - | Su ote | 2, |
| RAMO3- 03 RAE | ng | 318: 43 | ||
| femoe=2loo rune | Sine a | mare | ||
| feroizlo weroop? | rat oie | rnp | ro |
Tegan vox 17u Sa ey mere mes pucen 25] ma.e Sroor ove oe_vss vas ow etx (s
fs fs
fs
wont. (MOA LE- “pea to Revoir abit Rampi9— 5 ape a| q| tH al a *
/HSYNCDO. = /HSTNC moai7—Teo Yee 10 MOALS.
%* NOT INSTALLED
5-8
sexed >t cream faa os t>* Ho. crane Foa Foo PIXCLK
19d
- ZCRAMOE iso sasinc tc SIN
8K. » 1K ‘GND A190
| pete | de | ENO | fan enxes| | x | x | |
| —— | a0 | ry | ||||
| ot | Slee orl | 35 a|g——2o | lz —creeno | |||
| 32 | ae — | A | Cacy | Ho ofF$—Ho | aye REDS | |
| aio. ae | tne | Gres | ia | | He © a aeo3 | ||
| Ha]? & Shas | es | hr | ye & of — ile § als Ree | |||
| ae | Slee | oe | Ty slo Gh alte | info © ate ReDE | ||
| Da | coe | 2 3a | os | |||
| a | ory | pa} | if | 3815 ~ af | 3815 | gL? GREENS |
| genset | be 68 08 | 4 = | Aaa | |||
| Pra | enemupl24ftefe0 | mf prxcu tft | ||||
| i9K | GNO- | GNO- | /BLANK- |
a7, a
tit ee i
———. af ae guerra /PF3—TT
| vee; | of | 42{g $ ght — spr |
/OPS——PRIO gy th u i A HES b . Ye M0
| tes | | | 7 |
va ry +SVott -oB
PR Sv. 15y 419 F74 se 2 }p § a> — mon?
NOT INSTALLED
Figure 5-1 Badlands Game PCB Assembly Schematic Diagram, Sheet 4 of 6 06719401 C Schematic Diagrams
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Badlands Universal Kit ‘Schematic Diagrams
pia Ois—Ho ai —so7 o14a—Ho al — 806 c13—o ofS — S05 Brite x SEE a3 ox a bio Me & ae sue vats 09a | ops spr oe 500 cctre oe JAM-J
3, BE /MAINIRO.
Mrereeeses) TARMAR6 stv tec B56 nS Y +1038,
| : | rtest—etla yH2-so7 | cr | Lear | Less Lese | |
| Se | veeintRaea yB $06 | Hh | Opa | TUPI | Piovesu yore |
R33 R50 /AUDTRO—A ant ‘SPpPL ao = +5u—9rifa 2 HE S03 oe. -AGNO
| “att | Baz | ——i7lq ~ 1B | 500 | Ce | 36 C46 Ct | cas | NE HvSoS3 |
| warn | 20K | 19 | apa | Ta | 7. | arvesy |
prowl 8 cx Leiz -sy C2d4 ae -5y no. =5v
cs a ij} JAM-14
AGNoGNOS, Jan-m ca —— ee) 479/250
SYS sane
Figure 5-1 Badlands Game PCB Assembly Schematic Diagram, Sheet 5 of 6 047194-01¢
5-11
Schematic Diagrams Badlands Universal Kit
oN SENS eels 4 oe our GREENS ify — Hos GREEN2—HHp—t02 pow. GREENE ttf Sot GREENO. Zoo 1K ‘GND- }GNO ue Fi 25 ae : tre
pLues—p——Zlos cues BLUES. BLUEZ. BLUE.
JAMMA LEVELS ATARI LEVELS INSTALLED = 273,76,79,80,67, ANO 90 INSTALLED = R74,75,81,82,86, AND 89 2& NOT INSTALLED
Sheet 6 of 6 047194016 Figure 5-1 Badlands Game PCB Assembly Schematic Diagram,
5-13 iseliee}> SPARE.
ig +s
oreo B g EGE cas Leave Lcios bes ate fe qe te i elawloul cia Lene hci Leis ei oe tcioi Lexo0L ae coy Leos + fi e73 Less oso ters tere Lore Lore Lovs Leer Leac TET Te Te pe pepe pe ge
cava hen a . +50.
pees ces. Tea I T: aT zr ces Tove cos Lew Tere Len Lere Schematic Diagrams
Schematic Diagrams Badlands Universal Kit
SV j1-2
opt
JinL
Oty 1-4
RL J4-3
Steering PCB Assembly Schematic Diagram
Faulty RAM Locations
RAM Type Location. Video Display Characteristic
CPU/Video 22V Background color is red and foreground is black.
Color RAM 8K Black and yellow are the main colors.
Faulty Upper or Lower
Main ROM Locations
Error Address Location on Game PCB
00000, U=20F L=27F 20000 U=17F L=24F
ADDRESS
00000
008000
010000
FC0000
0000
FD0001
FEO001
FE2001
Fes001
FE60O1
Fe8000
FEROOO
FECOOL
FEEOOL Oo7FFF
OOFFFE
O3EFFF
FDOFFE
FRCOOO - FFC3FE
FPEQOO - FFEEFF
FFFOOO - FEFIEF
PRPOOO - FRFFFF SIZE
Lexa
eK
exw
2KB
25208
1688,
KB BADLANDS MEMORY MAP
ADDRESS BUS
2222 1111 1111 1100 0000 0000
3210 9876 5432 1098 7654 3210
C
o.
L
L
Ft
L
L 00 ORAA.
00 18BA
“AA AARA
00 000-
~00 000-
01 000A
-10 000-
10 001-
=10 ‘o10- AARA AAAA AAAA
AAAA AAA AAAA
AAAA AAAA AAAA
oll — — -aa-
on
a
100= = — —
1oi- — — —
ie —
110- -AA AAAA AAAO
l
AAA
AA AA
o
i
11 1210 AAAA AAAA AAAA
RRRR R
cece cco
-11 1122 0000 AAAA AAGO
0 orem me
0 Lee vg
1 Mee ror
“11 1111 AAAA AAAA AAAA 1111 1100 0000 0000
R/W 5432
R pppp R — pDpD R — pppa w
R
Rs
w
w
R
R
w ppp R — pppp Ww
w
R/W DODD
ppp
pop
D>
R/W DODD
pop
D>
R/w —DDDD
ppop
poop
R/w DDD DATA BUS
1098
Depp
poop
ppp
ppp
poop
pppp
pb
Dp
opp
ppp
poop
poop
ppp
ppop
pppD
ppop. 7654 3210
poop
pppp
ppp pope
poop
ppp
DDD DDD
DoDD DDD
poop
ppp ppp
boop oppo
ppp ppoD
DpDD DDD
Dopp ppp
D
poop
D
D
ppp
pop poop Schematic Diagrams
FUNCTION
SHORT ABSOLUTE PROGRAM PROM
SLAPSTIC PROGRAM PROM
LONG ABSOLUTE PROGRAM PROM
AUDIO RESET.
AUDIO TRANSFER LATCH FULL
BAROM
WATCH Dos
VEDEO IRQ ACKNOWLEDGE
SWITCHES
SELFTEST (ACTIVE 10)
VBLANK
BOTTON 1 (ACTIVE Lo)
BUTTON 2 (ACTIVE LO}
OPTION SWITCHES (ACTIVE LO}
LETA
WHEEL 1
WHEEL 2
PEDAL 1
PEDAL 2
AUDIO WRITE
AUDIO READ
PLAYFIELD STAMP BANK
EAROM UNLOCK
COLORAM
PLAYFIELD COLORAM
MOTION OBJECTS COLORAM
PALETTS
conor
RED
GREEN (MSB)
GREEN (LSB)
BLUE
PLAYFIELD PARAMETER RAM
ROW ADDRESS
COLUMN ADDRESS
COLOR PALETTE
STAMP NUMBER
MOTION OBJECTS PARAMETER RAM
Moe
STAMP NOMBER
vov
VERTICAL POSITION
VERTICAL SIZE
MoH
HORIZONTAL POSITION
VIDEO PRIORITY
COLOR PALETTE
PROGRAM RAM
Figure 5-2 Steering PCB Assembly Schematic Diagram, Faulty RAM and ROM Tables and Badlands Memory Map 047368.01 A
5-15
AC Alternating current; from zero it rises to 4 maximum positive level, then passes through zero again to a maximum negative level.
ACTIVE STATE ‘The true state of a signal. For example: The active state for is low.
ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero, ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is ap-
plied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a contol panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor), BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as 1 or 0. BLANKING Turning off the beam on a cathode-ray tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER 1, An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
- A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations. CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass.
CATHODE ‘The negative end of a diode.
CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electromechanical device that counts the coins inserted in the coin é mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.
Glossary
COMPLEMENTARY Having opposite states, such as the out- Puts of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video.
CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. DC Direct current, meaning current flowing in one direction and of a fixed value. DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory.
DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in a display to provide the high voltage. GATE
- A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
- A circuit in which one signal switches another signal on and off.
- To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as 2 base. The symbols 0-9 and A-F are usually used,
IMPLODE To burst inward; the inward collapse of a vacuum tube. vo Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode.
LOCKOUT COIL Directs coins into the coin return box when there is no power to the game.
gl-2 LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A device that takes several low-speed inputs and combines them into one high-speed data stream for simultaneous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request.
PAGE ‘A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit ~ board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER
- A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
- An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component levél by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located.
‘TROUBLESHOOT The process of locating and repairing a fault.
VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube.
WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.