Asteroids Deluxe Cocktail TM-174 1st Printing
Asteroids Deluxe (rev 3) (Atari, 1980) · Technical Manual · 52 pages · 51 sections · original scan
M174
GAME SERIAL NUMBER LOCATION Your game’s serial number is stamped on a plate on the outside of the game. The same number is also stamped on the chassis of the monitor, Regulator/Audio | PCB, and the Asteroids Deluxe™ Game PCB. Please mention this number whenever calling your distributor for service.
ASTEROIDS DELUXE ‘GAME PCB
‘GAME SERIAL # IDENTIFICATION TAG
Operation, Maintenance and Service Manual
Compiete with Illustrated Parts Lists
Copyright © 1981 by Atari, Inc. All rights reserved.
No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonograpnic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
Published by: ATARI INC. 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086
Lithographed in the U.S.A. 3K
Notice Regarding Non-Atari Parts
WARNING
Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
Atari, Inc.’s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:
1.) you substitute non-Atari parts in your coin-operated game, or
2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.
Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.
Table of Contents
1 Location Setup A. New Parts... 0.60. e eee etna B. Opening the Game Cabinet
- Table Top............
- Access Panel.......
- Closing the Table Top C. Game lnspection ... D. Game Installation. :
- Voltage Selection .........
- Interlock and Power On/Off Switches . —. Adjusting the Table Legs .... F. Self-Test Procedure .... G. Option Switch Settings
- Bonus Play Feature .
- Coin Mechanism Multipliers .......
- Examples of Game Price Settings . H. GamePlay ...........-......
- Attract Mode
- Ready-to-Play Mode OOOOADNMWHWWWWWA=
- PlayMode ......... . 13
- High Score Initial Mode .......... 0.6. e cece cence eee 13
2 Maintenance and Repair A. Cleaning... . 6.6... ccc cence tent eens 16 B. FuseReplacement.................5 ». 16 C. Switch Replacement . .. : . 16
- Leaf-Switch Replacement... . . 16
- LED Start-Switch Replacement ........... 2.000. c cece eee ee 16 D. Monitor Removal ..... 26.6060 cece cece ence eee e eee ees 18 E. Printed-Circuit Board Removal .
- Game PCB Removal ........ 19
- Regulator/Audio | PCB Removal.......... . 9 F. Speaker Replacement ... .. 20 G. Game Operation... .. 0... e tt ene e eens 20
3 Illustrated Parts Lists
List of Illustrations
Figure 1 Overview of Game .... 2... cee ec tee eee ae 2 Figure 2 Installation Requirements ... - 3 Figure 3 International Voltage Plug Selection............. - 4 Figure 4 Interlock and Power On/Off Switches .................00000.ee ee 4
Figure 5 Adjusting the Table Legs .......... 00... cece eee eee eee eee 5 Figure 6 Location of Self-Test Switch, Volume Control and Option Switches 6 Figure 7 Self-Test Procedure. . . Figure 8 Game Option Settings ......... 0... sce c eee eee eee enee 9
Figure 9 Game Price Settings. .......0..0. 0... c cece eee eee eee eee 10 Figure 10 Coin Counter Option Settings ... - 12 Figure 11. Opening the Control Panel and Replacing Switches . 17 Figure 12 Monitor Removal .......... 0.000 c cece cece eee eens 18
Figure 13 Printed-Circuit Board Removal . 19 Figure 14 Speaker Replacement .... . 20 Figure 15 Power Distribution . . 21 Figure 16 Signal Distribution ... 2.0.0... 0 ence eee 22
Iilustrated Parts Lists: Figure 17 | Cabinet-Mounted Assemblies Figure 18 Control Panel Assembly....... Figure 19 Regulator/Audio| PCB Assembly . Figure 20 Asteroids Deluxe™ Game PCB Assemb Yee cece ee eee eee eee 30
Figure 21 Power Supply Assembly for X-Y Games Figure 22 Double Coin Acceptor/Mount Assembly ... .
vi
WEST and CENTRAL U.S.A.
Parts for all Atari Customers. Sales and Service
Atari Coin-Op Customer Service 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103
(Monday - Friday, 7:30 - 4:00 pm Pacific Time)
s From California, Alaska or Hawaii (408) 745-2900
From anywhere else in this area toll-free (800) 538-1611
EAST U.S.A.
Sales and Service Only
Atari Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347
(Monday - Friday, 7:30 - 4:00 pm Eastern time)
zs From New Jersey (201) 469-5993
From anywhere else in this area toll-free (800) 526-3849
Location Setup
A. New Parts
The Asteroids Deluxe™/Cocktail game has three new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: @ New-Style Cocktail Table Cabinet. This cabinet design eliminates the side door and provides a new location for the game printed-circuit boards (PCBs). The table top is end-hinged for easy access to the PCBs and control panels. The coin box is accessible only from the outside of the cabinet. @ Game Circuitry. Most video games to date have used the raster-scan method of display. This game uses vector-generation. In addition, Asteroids Deluxe™ has non-volatile memory for part of the high score table. This means that even if power is removed from the game, the three highest scores will permanently stay in memory. To erase these scores follow the instructions in Figure 7, Self-Test Procedure. ®@ Coin Acceptor. This is Atari’s first use of this fixed-mounting dual coin acceptor. The doublethick front of the coin box serves as a lockable cover that closes flush with the front of the game cabinet. These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is
mentioned, you will see this symbol: —o)
. O)
SUPPORT ARM
TABLE TOP i
re taron =e Sh GAME PCB wr S ACCESS. a lez
PANEL CONTROL PANEL Re
“ COIN SWITCH, <] SELF-TEST SWITCH & VOLUME CONTROL REGULATOR/ AUDIO | PCB
POWER SUPPLY
START SWITCHES: {|| © LE : COIN ‘ COUNTER Yi GOIN BOX COIN ACCEPTOR “ 2]
Figure 1 Overview of Game W> SPEAKER SLAM SWITCH
B. Opening the ,® Game Cabinet
- Table Top @ To open the game cabinet unlock and open the two locks at one end of the game, located immediately below the table top (see Figure 1). @ Carefully lift the table top until the support arm locks into place. Do not jam the table top at the end of its upward swing.
- Access Panel @ To open the access panel, lift up the U-shaped steel bar inside the cabinet wall. @ The access panel near the bottom of the cabinet will then come out. This smal! panel was designed with a bar instead of the usual lock to reduce the number of keys required for this game.
- Closing the Table Top @ To close the cabinet, stand on the start-switch side of the cabinet and grasp the table top with your right hand. @ With your left hand, press the button at the middle of the support arm and pull the support arm toward the left. @ Gently lower the table top to the closed position. @ Lock the two latches on the left end of the cabinet, located just underneath the table top.
Cc. Game
Inspection
This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.
[to met NOTE remy Do not plug the game in yet!
- Examine the exterior of the game cabinet for dents, chips, or broken parts.
- Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don't force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the Game PCB are firmly seated in their sockets.
@ Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verity that the serial numbers also stamped on the Asteroids Deluxe™ Game PCB, Regulator/Audio | PCB and monitor are all identical. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, control panel and monitor for secure mounting.
D. Game Installation
Figure 2 Installation Requirements Power 150 watts Temperature 0 to 38° C (32 to 100°F) Humidity Not over 95% relative Space Required 62% x 82% cm (24% x 32% in.) Game Height 61 to 72% cm (24 to 28% in.)
- Voltage Selection This game has two possible power supplies: the U.S. power or international power supply. The U.S. power supply operates on one line voltage range: 105 to 135 VAC. The international power supply has four colored voltage selection plugs and operates on the line voltage of almost any country in the world.
Asteroids Deluxe ™/Cocktail
Line Voltage Range Plug Color 90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (225) Blue 220-260 VAC (240) Brown
Figure 3 International Voltage Plug Selection
SAFETY
SWITCH COVER
POWER ON/OFF SWITCH Reach Under Game: To Activate Switch
Figure 4 Interlock and Power On/Off Switches
Before plugging in your game, check your power supply. If the supply doesn’t have voltage selection Plugs and a connector at J3 (see Figure 3), then the game operates on any voltage from 105 to 135 VAC. If the supply has the colored selection plugs, check the wire color on the plug and see if it is correct for your location (see Figure 3).
- Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, an interlock switch has been installed under the table top (see Figure 4). This switch removes all AC line power from the game circuitry when the table top is opened.
Check for proper operation of the interlock switch by doing the following: @ Make sure the table top is closed. Plug the AC power cord into an AC outlet. @ Set the power on/off switch to the on position. Within approximately 30 seconds the monitor should display a picture. @ Slowly open the table top. The monitor picture should disappear when the panel is opened approximately 2% cm (1 inch). @ = Ifthe results of the preceding step are satisfactory, the interlock switch is operating properly. If the monitor doesn't go off as described, check to see if the interlock switch is broken from its mounting or stuck in the on position.
E. Adjusting the Table Legs
This cocktail-table game is designed for three adjustable heights—61, 66 or 72% cm (24, 2642 or 28% inches). To adjust the table height, refer to Figure 5.
If you adjust the game for any except the lowest height, you should insert the black plastic plugs into the exposed table leg mounting hole(s) in the cabinet. These plugs are fairly tamper-proof from the outside, yet are easily removed from the inside of the cabinet. Simply push the plugs out with a pencil or screwdriver.
Before removing the table legs, be sure to ‘support the game on its bottom surface with books or a tool chest, etc. An assistant can also hold one end of the game. Then change the position of the legs. Atari does not recommend tilting the game up and standing it on its end! USE ALL THREE BOLTS WHEN ATTACHING TABLE LEGS!
Figure 5 Adjusting the Table Legs
Asteroids Deluxe ™/Cocktail
F. Self-Test
Procedure
This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the monitor and the game speaker; no additional equipment is. necessary.
Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game’s options. OPTION SWITCH (ONE OF THREE SETS)
To run the self-test, follow the instructions out- or lined in Figure 7.
i) COIN SWITCH (FOR
OPERATOR CONVENIENCE) VOLUME CONTROL VOLUME DECREASE: TURN CLOCKWISE SELF-TEST SWITCH
Figure 6 Location of Self-Test Switch,
Volume Control and Option Switches
Figure 7 Self-Test Procedure
Results if Instruction Test Passes Results if Test Fails
| 1. | Set self-test | The monitor displays | RAM FAILURE is indicated by a sequence of low and high beeps. Note the sequence |
| switch to on posi- | the picture below. The | of beeps and determine which RAM(s) may be bad. To restart the sequence, press the | |
| tion (see Figure 6). | game produces onlya | _reset pushbutton on the game PCB, or set the self-test switch to off, then again to the |
very short beep ‘on position. sound, Possible Bad ‘Sequence of Beeps RAM Chip Location(s) 1 low ut 2 lows U1, M1 1 high, 1 low M1 2 highs, 1 low M3 2 highs, 2 lows M3, R3 3 highs, 1 low R3 4 highs, 1 low NB 4 highs, 2 lows N3. P3- 5 highs, 1 low PS Any bad RAMs must be replaced before the self-test can continue.
ROM/PROM FAILURE is indicated by the display of the actual PROM or ROM chip location(s) on the center left side of the monitor screen. Both a PROM and its equivalent ROM are inserted into the same socket. Therefore, the displays are correct regardless of whether your game PCB has PROMs or ROMS or a combination of both. If the screen is blank or displays “garbage,” the chips at locations N2 and/or J1 are probably bad.
INVERTING CIRCUITRY FAILURE is indicated by the BANK ERROR message in the lower center part of monitor screen. This circuitry is necessary for the cocktail-table version to function properly, that is, the picture turns 180° with every other ship in Example only—detail on next 2-player cocktail games. page explains these four rows of symbols. AUDIO CHIP FAILURE is indicated by the ERROR message at center bottom of the Screen, The large audio chip is at location M7/8 on the game PCB.
| 2. | Activate all 5 | As you activate and | You will not hear a short low beep for the defective switch, or dark LED. |
control-panel switch- deactivate each es, the slam switch, switch, you'll hear a the start switches, short low beep. Both and coin door start switch LEDs will switches. be constantly lit.
- Erasing the High Score Table (optional) The current three highest scores are held in permanent memory, even if the game is unplugged. These three are marked with spaceship symbols in the high score table. |f you want to erase these scores, simultaneously press the rotate left, rotate right, thrust, and fire buttons. The ERAS/NG message near the center of the screen will then be displayed for several seconds, until the entire table is erased.
- When satisfied with test, set selftest switch to off position.
[Selt-test continued on next page]
Asteroids Deluxe ™/Cocktail
Figure 7 Self-Test Procedure, continued
Coin Bonus Adder 0, 5, 6 or 7 = No bonus coins 1 = For every 2 coins” inserted, game logic adds 1 more coin* 2 = For every 4 coins” inserted, game logic adds 1 more coin” 3 = For every 4 coins” inserted, game logic adds 2 more coins” 4 = For every 5 coins” inserted, game logic adds 1 more coin*
Left Mech Multiplier 0 = Left coin mech x 1 1 = Left coin mech x 2
ight Mech Multiplier Right coin mech x 1 Right coin mech x 4 Right coin mech x 5 = Right coin mech x 6
Game Price Free play 1 coin® for 2 plays 1 coin* for 1 play 3 = 2 coins* for 1 play *in the U.S. a “coin” is defined as 25¢. In Germany a “coin” is 1 DM.
Game Language 0 = English German French = Spanish
Ships at Game Start 0 = Game starts with 2 to 4 ships 1 = Game starts with 3 to 5 ships 2 = Game starts with 4 to 6 ships 3 = Game starts with 5 to 7 ships (See graphic display in third line for exact number of ships)
Minimum Number of Plays 0 or 2 = 1-play minimum 1or3 = 2-play minimum
Bonus Ship 0 = Bonus ship at every 10,000 points Bonus ship at every 12,000 points Bonus ship at every 15,000 points 3 = No bonus ship (adds 1 ship at game start) ape
Graphic display of number of ships per game (up to 7)
| a O la Point score at which a bonus ship is granted (blank if Ro bonus ship)
G. Option Switch Settings
- Bonus Play Feature Asteroids Deluxe™Cocktail is one of the first Atari games to offer a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.
For example, with your game set at 50¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, will receive a
oops play. Therefore, players receive 3 plays for
1.
This bonus feature encourages piayers to insert more money than just the minimum 50¢ you could require for one game. Various other bonuses are available (see Figure 9).
- Coin Mechanism Multipliers The Atari coin acceptor mount for this game is available with about a dozen different mechanisms. You may have both mechanisms accept the same or different denominations. Asteroids Deluxe ™/Cocktail
Regardless of the type of mechanism you install, you must correctly set the “multipliers” for each mech on the game PCB. The multipliers determine how much each mechanism will be worth to the game's logic.
The basic unit of measurement is 25¢, which equals a multiplier of x1. Therefore, if you have a 25¢/$1 coin acceptor, you will probably want to set the left and right option-switch multipliers at x 1/ x 4.
You can set these multipliers with toggles 3 thru5 on the Asteroids Deluxe™ PCB switch assembly at location L8. For exact settings of these toggles, refer to Figure 9.
- Examples of Game
Price Settings
Figure 9 explains the options, giving twelve examples of the most common U.S. situations. The toggles mentioned are all in the switch at location L8; they only relate to game price, coin mechanism multipliers, and the bonus credit for multiple quarters or the $1.00 coin. You should set the toggles relating to other functions as you see fit, although Figures 8, 9, and 10 provide “$” signs indicating Atari’s recommendations.
Figure 8 Game Option Settings To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the Asteroids Deluxe™ Game PCB is mounted in place. When changing the options, verify proper results on the monitor display by performing the self-test. Note that changing an ‘option on any of the following eight toggles will cause an immediate change on the monitor screen during the self-test.
Toggle Settings of 8-Toggle Switch on Asteroids Deluxe PCB (at R5—LEFT switch when PCB is in game) 8 7 6 5 4 3 2 1 Option
On On Off Off
On On On Off
Off On
Off Off
On Off
Not Used
On On On Off
On English language $ Off German language On French language Off Spanish language Game starts with 2 ships Game starts with 3 ships $ Game starts with 4 ships Game starts with 5 ships ‘play minimum $ 2play minimum Bonus ship at every 10,000 points $ Bonus ship at every 12,000 points Bonus ship at every 15,000 points No bonus ship If set for no bonus ship or 50¢ play, add 1 ship per setting.
$ Manufacturer's suggested settings
Figure 9 Game Price Settings The white block below contains Atari’s suggested settings. All numbers 1 thru 8 are toggle settings on the 8-toggle switch at location L8, on the Asteroids Deluxe™ game PCB (the CENTER switch assembly).
50¢ PER PLAY: Bonus $.50 = 1 play Bonus $.75 = 2 plays $1.00 = 3 plays $1.00 = 3 plays
All 25¢ Mechs
25¢1$1.00 |, Mechs
25¢ PER PLAY:
Bonus Bonus No bonus $.50 = 3 plays $1.00 = 5 plays
| 7 | 6 | 5 |
| On | On | On |
All (2) On 25¢ Mechs
| 4 | 3 | 2 | 1 |
| On | On | Off | On |
Circled numbers refer to game pricing labels you Use the label no. 6 (indicated above with ©) only should use with each situation (labels are illustrated if you set toggle 5 at PCB switch assembly R5 to off. on the following page).
| Figure | 9 | Game Price Settings, continued |
For your information, we have defined below the switch set- The labe! no. 6 shown below should be used only if you set togtings for those options relating to game price, coin mechanism gle 5 at PCB switch assembly R5 to off. multipliers, and bonus play. This information is useful in case you need to temporarily set the Asteroids Deluxe™ game on free play, or if you have German coin mechanisms in your door.
Toggle Settings of 8-Toggle Switch on Asteroids Deluxe PCB (at L8B—CENTER switch when PC!
| 8 | 7 | 6 | 5 | 4 |
1 Option
| On | On | Free play | |
| On | Off | 1 coin” for 2 plays | |
| Off | On | 1coin* fort play | $ |
| Off | Off | 2 coins” for 1 play | |
| On | On | Right coin mech x 1 | $ |
| On | Of | Right coin mech x 4 | |
| Off | On | Right coin mech x 5 | |
| Off | Off | Right coin mech x 6 | |
| On | Left coinmech x 1 | $ |
Off Left coin mech x 2
| On | On | On | No bonus coins |
| On | On | off | For every 2 coins" inserted, game logic adds 1 more |
coin®
| On | Off | On | For every 4 coins” inserted, game logic adds 1 more |
coin*
| On | off | off | For every 4 coins” inserted, game logic adds 2 more |
coins” $
| Off | On | On | For every 5 coins” inserted, game logic adds 1 more |
coin*
"In the U.S., a “coin” is defined as 25°. In Germany a “coin” is 1 DM.
$ Manufacturer's suggested settings To achieve bonus plays, all coins must be inserted before pushing Start button. nO @@ 2 coins Am Q@@ 3 coins 006 @ 4 coins
© @6@ 2 coins =1 play A @ $1 coin =3 plays (Susan B. Anthony coin) tC) J, @@ 2 coins =1 play ATARI
On @ 1 coin = 1 play ame’ 2 play minimum (2 coins = 2 plays) e
| AL | @ | 1 coin | = | 1 play |
ATARI
ara the appropriate phrase. Use a *
KO @ @ 2 coins = 1 play e A (For operator use—write in
permanent-ink water-resis- 4 coins = 3 plays ATARI! tant marker. 6000
an)
Figure 10 Coin Counter Option Settings
[These toggies determine which coin mechanisms activate which counters]
Toggle Settings of 4-Toggie Switch on Game PCB (M12)
| 4 | 3 | 2 | 1 |
Two coin acceptors in the coin door: Two coin acceptors and a pushbutton utility coin switch in the game: Three coin acceptors in the coin door:
| On | On | Both acceptors activate all coin |
counters simultaneously.
| Off | On | Both acceptors activate 2 count- |
| = | & | ers separately. |
& 8 3.3
| S | $$ | On | Off — Both acceptors activate all coin |
counters simultaneously.
| Off | Off | Both acceptors activate 2 count- |
ers separately. Do not use this setting.
Do not use this setting.
Utility coin switch will not activate a coin counter, if you do not hook it up. Both acceptors activate all coin counters simultaneously.
Utility coin switch will not activate a coin counter, if you do not hook it up. Left and right acceptors activate 2 coin counters All 3 are same denomination and they activate all coin counters simultaneously.
Left and center acceptor activate ‘one coin counter, right acceptor activates another coin counter.
Left acceptor activates one coin counter; center and right acceptor activate another coin counter. Not for any currently designed 3-mech coin door.
Left, center and right acceptors activate 3 coin counters separately.
separately. §
$ Marufacturer’s suggested setting
H. Game Play
Atari’s Asteroids Deluxe™ is a one- or two-player game with an X-Y or vector-generator monitor. The game depicts a third-person view of a player's spaceship battling to destroy asteroids, flying saucers and enemy ships or “death stars” (shaped like clusters of triangles). When hit, the asteroids and death stars will break into progressively smaller pieces.
Players can put up an octagon-shaped “shield” to temporarily protect their spaceship. However, this shield wears out with use.
The game has five possible modes of operation: Attract, Ready-to-Play, Play, High Score Initial, and Self-Test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, ali game credits are cancelled.
- Attract Mode
The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when you enter self-test.
In this mode, the monitor displays two possible pictures. One picture is of randomly tumbling asteroids, large and small saucers, and death stars—all in a simulated game. The other picturé shows the ten currently highest scores.
If you erase the special “permanent” memory (see Figure 7, Self-Test Procedure), then the second picture with the high-score table will not appear on the screen. The table is redeveloped from scores of subsequent games.
- Ready-to-Play Mode This mode begins when sufficient coins have been accepted for a one- or two-player game. It ends when the 1 PLAYER START or 2 PLAYER START Pushbuiton is pressed.
Operators may choose one- or two-play minimums by selecting one of the option switch settings on the game PCB (see Figure 8, Game Option
Settings). If you select the two-game minimum anda player inserts enough money for only one game, the message 2 GAME MINIMUM flashes on the screen until the required number of coins is inserted.
When this mode begins, the message PRESS START flashes immediately below the center score at the top of the screen. The displayed pictures are otherwise the same as those shown in the attract mode.
- Play Mode The play mode begins when either start pushbutton is pressed. The mode ends when the player's last ship of the game is lost.
Six large asteroids appear and drift in from the outer edges of the display. By pressing the ROTATE LEFT and ROTATE RIGHT pushbuttons on the control panel, the player may aim a spaceship toward any of the asteroids. The player uses the FIRE pushbutton to shoot at the asteroids and other objects.
When shot, each large asteroid divides into two medium-sized asteroids, and the game adds 20 points to the player's score. Medium-sized asteroids, when shot, divide into two small-sized asteroids, and the game awards 50 points to the player. When shot, the smallest asteroid disappears and the game adds 100 points to the player's score.
When players shoot all asteroids, a new set of large ones again appear and drift in from the outer edges of the monitor display. At the beginning of the next cycle six large asteroids reappear, then eight, and thereafter ten—to increase player challenge.
In addition to asteroids, the players can score points for shooting the various enemy ships. When hit, the large ships (‘death stars” shaped like hexagons) score 50 points and break into three diamond shapes. The medium-sized enemy or diamond, when hit, grants the player 100 points and breaks into two small triangular pieces. These small Pieces disappear when the player hits them, and the score increases by 200 points.
At any time during game play, a flying saucer may appear from either side of the display. The game awards players 200 points for shooting a large saucer and 1000 points for a small saucer. (The latter is a smaller target for players, though not any faster moving than the large one. It also shoots more accurately.) The player's objective in the game is to shoot and destroy as many asteroids, saucers, and enemy ships as possible before all his or her spaceships are destroyed. A ship is destroyed if an asteroid, saucer or enemy ship smashes into it, or if a flying saucer shoots it. To prevent losing a ship, the player may press the THRUST pushbutton to move out of the path of an oncoming object.
As an emergency maneuver, a player can press the SHIELDS pushbutton. An octagon will then appear around the player’s ship as protection from all enemies. For challenge the shield power lasts only about 10 seconds, but the power is renewed with each ship. The amount of shielding power available is shown by the brightness of the octagon (dim means almost exhausted power).
An operator option allows you to award an extra ship each time a player's score reaches multiples of 10,000, 12,000 or 15,000 points. As an alternative, you may not offer any bonus ships at all to players. Refer to Figure 8, Game Option Settings, for how to set your game for this option.
When the last ship of the game is destroyed, the message GAME OVER appears below the high score. This message remains for three seconds before the high score initial mode begins.
- High Score Initial Mode At the beginning of the high score initial mode, the player instructions appear at the top of the screen, and A ____ appears at the lower center of the display. Players enter initials one character at a time.
By pressing the ROTATE LEFT pushbutton, the displayed character steps through the alphabet from Ato Z. By pressing the ROTATE RIGHT pushbutton, the character shown will step backwards through the alphabet from A to a blank space, then from Z to A. Once the game displays the desired letter, players should press the SHIELDS pushbutton to record the letter; then an A appears in the next space.
If players need only two letters for their initials, they should use the blank between Z and A in one of the three locations. Pressing the SHIELDS pushbutton a third time will cause the initials and game score to be transferred to the high score table. This table contains a maximum of 10 scores and appears during the attract mode.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Maintenance and Kepair
All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.
The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if light-emitting-diode (LED) switches or leaf switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.
Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly clean the leaf-switch contacts: for details see this chapter.
A. Cleaning
The exterior of the game cabinet and the metal and glass surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor.
The large monitor shield is made of tempered glass and should be scratch-resistant: if cleaned without abrasive substances, you should hardly ever have to replace it.
B. Fuse Keplacement
C. Switch Keplacement
This game contains six fuses—all on the power supply assembly (not including the monitor fuses). Replace fuses only with the same type as listed in Figure 21 of this manual. See the Quadrascan™ monitor manual for the monitor fuse data.
Prior to repairing or replacing any switch on the panel, first unplug the game. Next, open the game top as described in Chapter 1, Section B, Opening the Game Cabinet. Finally, remove the two sets of button-head screws and lock washers at the top edge of the control panel.
Once this hardware is removed, the control panel will tilt toward you.
- Leaf-Switch Replacement All five of these leaf switches operate on 5 volts at a very low current. Therefore, pitting of these switches would be extremely rare. Probably the only reason that pitting would occur is in very highhumidity locations.
Don’t burnish the switch contacts. Burnishing them removes their plating, thus increasing the cor rosion of the contacts. The best method of cleaning the switch contacts is to wipe them with a non-abrasive surface. A business card works very well.
To replace any switch, remove both of its screws with a Phillips-head screwdriver—see Figure 11.
If the white button itself needs to be replaced, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The white ring on the outside of the control pane! should not spin, due to its design.
- LED Start-Switch Replacement The light-emitting diode (LED) switches near the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 11.
@ Remove the wires from the suspected switch. ® Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter. @ Connect multimeter leads to appropriate LED switch contacts (see Figure 11 for designation of switch contacts). @ Check contacts (push and release the switch button) for closed and open continuity. @ If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.
Asteroids Deluxe ™/Cocktail
NORMALLY CLOSED To remove LED switch: y (NC) CONTACT
» NORMALLY OPEN (N.O.) CONTACT Remove all wires from the faulty switch.
Turn the switch counterclockwise while holding the black Qe
cone-shaped bushing on the outside of the control panel. Install a new switch using the reverse procedure. . Reconnect the harness wires. \ LIGHT-EMITTING-DIODE COMMON ~ CONTACT (L.E.D.) CONTACTS
TO REMOVE WHITE BUTTON oF J | TURN NUT
i
Figure 11 Opening the Control Panel and Replacing Switches
D. Monitor Kemoval
A— WARNING
High voltages may exist in any television monitor, even with power disconnected. Use extreme caution and do not touch electrical parts of the yoke area with your hands or with metal objects in your hands! If you drop the monitor and it breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any monitor. If you should need to remove the Quadrascan™ X-Y monitor, follow steps 1 thru 5 as listed on this page. Refer also to Figure 12.
1.
2. Be sure the game is unplugged from its wall outlet! Unlock and open the table top. Lift up the “U-shaped security bar, located along the inside wall of the cabinet. Remove the bar entirely from the cabinet. Push the access panel outward from the inside of the game. Locate the 12-pin monitor connector underneath the monitor, just above the power supply transformer. Unplug this connector. Remove the four Phillips-head screws and flat washers (one set at each corner of the monitor screen) that attach the monitor to the cabinet. Remove these screws. Carefully lift the monitor chassis up and out of the cabinet.
Disassemble in the order indicated. (Circled numbers match the steps above.)
Figure 12 Monitor Removal
E. Printed-Circuit
Board Kemoval
You may wish to remove the game printed-circuit board (PCB) or the Regulator/Audio | PCB for service or inspection. To do this, refer to Figure 13 and proceed as follows:
- Game PCB Removal @ Unlock and open the table top. @ Remove the nylon tie wraps from the top side of the game PCB. Then remove the 44-pin edge connector. @ Locate the Phillips-head screws that extend through the PCB and into the two wood blocks near the top of the game. Remove these two screws and the associated fiber washers. @ Remove the PCB from the game by sliding it up out of the plastic PCB retainers. N Asteroids Deluxe™/Cocktall
Reinstall the PCB, making sure that the 44-pin edge connector is properly plugged in. Note that the connector is keyed to fit on only one way, so if it doesn’t slip on easily, don’t force it! A reversed connector will probably damage your game and will void the warranty. Check that the operation of the game is correct and perform the self-test. This is especially important with any game when you replace a PCB.
Regulator/Audio | PCB Removal Unlock and open the table top. Remove the three plug-in connectors. Locate the Phillips-head screw that extends through the PCB and into the wood block at the top of the PCB. Remove this screw and its associated washers. Remove the PCB from the inside wall of the cabinet by pulling it up and out of the wood retainer.
GAME PCB.
REGULATOR! AUDIO! PCB
Figure 13 Printed-Circuit Board Removal
Asteroids Deluxe ™/Cocktail
PLUGIN WIRE CONNECTORS \
Figure 14 Speaker Replacement
F. Speaker Replacement
If the loudspeaker should ever need to be replaced, follow the instructions below and refer to Figure 14. Probably the only cause of speaker failure is an open voice coil or a ruptured cone, but both of these failures are highly unlikely.
Open the table top. Unplug both speaker-wire connectors. If the speaker is stap/ed to the cabinet wall, use a flat-bladed screwdriver to pry loose the staples that secure the speaker.
If screws are used to secure the speaker, use a very short-handied Phillips screwdriver to remove the four screws. For greater ease in reaching these screws, and to prevent slipping and damaging the Regulator/Audio | PCB, remove this PCB first.
G. Game Operation
With this manual you received two large sheets that contain the wiring and schematic diagrams for the Asteroids Deluxe™/Cocktail game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. These diagrams include information that explains the functions of the circuits and defines inputs and outputs.
Atari's Asteroids Deluxe™ is a microprocessorcontrolled game. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCB and output to the monitor, Regulator/Audio | PCB, loudspeaker, and control panel.
The monitor is an X-Y monitor. Therefore, the monitor receives signals for the X, Y and Z axes. Since the location of the beam in the monitor is totally controlled by the X- and Y-axis outputs of the game PCB, the game PCB does not contain a standard sync circuit. The X- and Y-axis imputs to the Monitor step in increments of 1024 steps for the X (horizontal) axis, and 768 steps for the Y (vertical) axis. The Z axis merely controls the intensity of the beam. The Regulator!Audio | PCB performs two functions: 1) it regulates the +10 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio | PCB provides most logic power to the game PCB. The audio output from the Regulator/Audio | PCB directly drives the game speaker and is controlled by the volume control, mounted on the bracket inside the game.
The Power Supply is the source of all voltages in the game. These voltages are protected by five fuses (F2, F3, F4, F5 and F6) on the power supply chassis. The primary winding of the power supply transformer is protected by the cartridge-type fuse F1 in the power supply chassis.
Figure 15 illustrates the distribution of power in this game. Figure 16 illustrates the distribution of signals.
MONITOR
INTERLOCK GAME PCB Meas
REGULATOR! AUDIO | PCB
N
POWER SUPPLY
POWER ON/OFF SWITCH
COIN MECHANISMS.
Figure 15 Power Distribution
Asteroids Deluxe ™/Cocktail
START SWITCHES
GAME PCB CONTROL PANEL
SELF-TEST SWITCH
VOLUME CONTROL
COIN SWITCH
X-Y MONITOR SPEAKER1&2 REGULATOR/ AUDIOIPCB
SPEAKER
SLAM SWITCH
COIN MECHANISMS
COIN COUNTER
Figure 16 Signal Distribution
Illustrated Parts Lists
This chapter provides you with the necessary information for ordering replacement parts for your Asteroids Deluxe™/Cocktail game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.
The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
03585201 = y (Corner Brkt.) GP 2) 82-406 (Eyebolt)
035911.01 | (Bezel) ot nN e
78-3118, 178015-001 (Top Support)
92.045 (Y Monitor)
> 036772.01 (Access Door)
Power Supply Assy.— See Figure 21 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any tight in, of license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any ‘right to reproduce this drawing ar any part thereof. Except for manufacture by vendors of Atari, Inc., and for manutacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation.
035851.01 (Hinge)
033127-01 (Sw. Bushing) 62-039 (LED Sw.) 75-9910WO (Nut) 71-2110 (Lock)
03677701 4 (Wood Cab. Assy.)
'82-8940B (Screw)
"A035895-01 (Leg)
Figure 17 Cabinet-Mounted Assemblies A036780-01 A
Asteroids Deluxe ™/Cocktail
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Reproduction Yorbidden without the specific written permission of tan, Inc. Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt 78-6900401 nor possession thereof confers or transfers any right in, oF (Tape) license to use, the subject matter of the drawing or any design or technical information shown thereon.nor any Tight to reproduce this drawing or any part thereof. Except for manufacture by vendors of Ala, Inc., and for manutacture under the corporation's written license, no right to re. produce this drawing is granted or the subject matter {hereof unless by written agreement with or written per mission from the corporation 035867-02 (Overlay) 7 sco 036781.01 Game PCB— (Glass Top) See Figure 20 A036845.01 > (Main Harness) 036788-01 (Security Bar)
036774-01 Grille)
Control Panel Assy.—. 68-002 See Figure 18 (Interlock Sw.) 00788202 034546-03 (Interl. Sw. Cvr.) (vibration Damper) 69-001 peptone (Slide Sw.) (PCB Retainer) 19.9032 A034841.08,, A036320-01 (Rheostat) A034861.08, (Vol. Ctrl./Test Sw. 62-041 Anzseno.eg & Coin Sw. Assy.) J (pyshbtn. Sw.) wer ower Core) 036321-01 48-004 (Bracket) (Speaker) 000869-01 (Speaker Grille)
036773-01 Grille) ‘A007638-01 009992.01 (Slam Switch Assy.) (On/Off Sw. Cvr.) A034631-01 (Toggle Switch)
Schematics, Self-Test Labels & Mat see parts list on opposite page (Coin Box) A002465-01 (Coin Counter Assy.) Reg/Audio | PCB— See Figure 19 OS coin Acceptor— ‘See Figure 22
Figure 17 Cabinet-Mounted Assemblies A036780-01 A
Asteroids Deluxe “Cocktail
Figure 17 Cabinet-Mounted Assemblies, continued Parts List
Part No. Description
A002465-01 Coin Counter Assembly A007638-01 Slam Switch Assembly A034629-01 AC Harness Assembly A034631-01 On/Off Switch Assembly A034841-08 Strain Relief Power Cord Assembly (U.S.) A034861-08 Strain Relief Power Cord Assembly (German) A035895-01 Cabinet Leg A035989-08, Strain Relief Power Cord Assembly (Australian) A036320-01 Volume Control/Test Switch/Coin Switch Assembly A036775-01 Coin Box
| A036777-01 | Wood Cabinet Assembly | (a/so includes legs, hinges, grilles, and lock) |
A036845-01 Main Harness Assembly (a/so includes on/off switch, interlock switch and its bracket, slam switch, and volume control and its bracket) DP-174-01 Sheet 1 of Asteroids Deluxe™/Cocktail Schematic Drawing Package OP-174-02 Sheet 2 of Asteroids Deluxe/Cocktail Schematic Drawing Package ST-174-01, -02 Asteroids Deluxe/Cocktail Self-Test Label TM-174 Asteroids Deluxe/Cocktail Operation, Maintenance and Service Manual TM-151 Quadrascan™ X-Y Monitor Manual 19-9032 50-Ohm, 12/2 Watt, Wire-Wound Rheostat (for volume control) 48-004 8-Ohm, 5-W, 5-Inch Loudspeaker 62-039 Momentary-Contact SPDT Light-Emitting Diode Switch 62.041 SPDT Momentary-Contact Pushbutton Switch (for utility coin switch) 68-002 30-Amp Interlock Switch 69-001 DPOT Slide Switch (for self-test) 71-2110 Panel Cartridge Lock Mechanism 75-9910W0 15/32-32 Steel Stamped Nut
| 78-3118 | Top Support Assembly | (right side—for left side support: see part number below) |
78-3205 End Cap (for cabinet leg) 78-3206 Cabinet-Leveling Foot 78-6900401 ¥4-Inch Foam-Backed Adhesive Tape 82-406 #%-20 x 2-Inch Machine-Thread Eyebolt 82-8940B #3/8-16 x 2¥2-Inch Button-Head Hex Socket Machine Thread Screw 92-045 16-Inch X-Y Monitor 000869-01 Speaker Grille 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 033127-01 Black Molded Switch Bushing 034546-03 Foam Vibration Damper 035745-02 18-Inch PCB Retainer 035851-01 Hinge 035852-01 Corner Bracket 035867-02 Smoke-Color Acrylic Overlay 03591 1-01 Monitor Bezel 036321-01 Bracket (for self-test, volume control and coin switch assembly) 036686-01 Game Pricing Labels 036772-01 Access Door 036773-01 Ventilation Grille (for base} 036774-01 Ventilation Grille (for upper side) 036781-01 Glass Top with Graphics 036788-01 Security Bar
| 178015-001 | Top Support Assembly | (Left Side) |
178018-003 Cabinet Hole Plug
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING A036848-01 CONFIDENTIAL: Reproduction forbidden without tne ie wrtton permission of Att inc, Sunnyvale (Control Panel Harn. Assy.) eth arawing 6 only conalionally Issued, and A036765-01 naliner receipt or posession thereat cones o ransters any right ino” license to use, he subject (Control Panel) Imalter of the drawing or any design or technical infor ‘mation shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to repro. duce this drawing is granted of the subject matter thereof unless by writien agreement with or written permission trom the corporation.
60004-001 (Leaf Sw.)
75-9910NO (Nut)
160001-001 (Leaf Sw. with Button Holder)
A036046-01 (Button Assy.)
Figure 18 Control Panel Assembly A036778-01 A
Parts List
Part No. Description
A036046-01 Button Assembly A036765-01 Control Panel with Graphics A036848-01 Control Panel Harness Assembly 75-9910NO §/8-11 Steel Stamped Nut 160001-001 Leaf Switch with Button Holder 160004-001 Leaf Switch Only
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
CONFIDENTIAL: Reproduction forbidden without the
formation shown thereon,
nor any righ s drawing or any part
thereof. Except for manufacture by vendors of At
is drawing is granted or
s by written agreement FIO.3VOC UNA JT Ed 3 300 2 300 os cro ; ce ay 13
Db cn os eb a8 a k's ee
; =
A A034485-03 Figure 19 Regulator/Audio | PCB Assembly
Figure 19 Regulator/Audio | PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Bold)
12-52P7 2.7 Ohm, + 5%, 1W Resistor (R5) 19-100P1015 -1.Ohm, + 3%, 7W Wirewound Resistor (R24) 19-315102 1K Ohm Vertical PCB-Mounting Cermet Trimpot (R8) 24-250108 1000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C13) 24-250477 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C1, 4, 12) 24-350338 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10) 29-088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, C11) 31-1N4002 100V 1-Amp. Silicon Rectifier 1N4002 Diode (CR1, 4) 33-TIP32 PNP Power Transistor, Type TIP32 (Q2) 34-2N3055 NPN Silicon Transistor, Type 2N3055 (Q3) 37-LM305 5V Linear Voltage Regulator (Q1) 75-F60405 #6-32 x ¥% Inch Binder-Head Nylon Screw 78-16008 Thermally Conductive Compound for the 2N3055 78-16014 Thermally Conductive Compound for the TIP32 79-58306, 6-Position Connector Receptacle (J6) 79-58308 9-Position Connector Receptacle (J7) 79-58354 4-Position Square Connector Receptacle (J8) 020670-01 Test Point 034531-01 Heat Sink 100015-103. .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C5, 14) 110000-010 1 Ohm, + 5%, %W Resistor (R10, 19) 110000-100 10 Ohm, + 5%, %W Resistor (R11, 20, 25, 26) 110000-101 100 Ohm, + 5%, %W Resistor (R4, 12, 22) 110000-102 1K Ohm, + 5%, %W Resistor (R15, 16) 110000-103 10K Ohm, + 5%, %4W Resistor (R13, 14) 110000-271 270 Ohm, + 5%, %4W Resistor (R1) 110000-330 33 Ohm, + 5%, YW Resistor (R3) 110000-392 3.9K Ohm, + 5%, YW Resistor (R6) 110000-752 7.5K Ohm, +5%, %4W Resistor (R7) 110001-221 220 Ohm, + 5%, v2W Resistor (R9, 21) 122002-102 .001 uf Ceramic-Disc 25V Radial-Lead Capacitor (C2, 7, 16) 122004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C6, 8, 15, 17) 137151-002 8W Linear Audio Amplifier integrated Circuit (Q5, 7)
>000000000, ._ Detail of PCB at Locations E2 and P1: | 000000000" Use IC pads enclosed with dotted lines when inserting 74LS245. 2 ET care} f) (cee Ohl Gee 6 case ea sae} [ised MM arse
He = = & ey Asteroids Deluxe ™/Cocktail
ree FREE SORE ges
Ft is et eax, rr) a6a03 [= aS tif son, [caw Pa = rer) Tea ¢ Pa [73 [Ss we273 | at =
Se a sce? [ueaz? a [ea] Ss Be gaa a wien? a ea | Eers) =, PR tae [axed ise} 2 4 6 8 10
Figure 20 Asteroids Deluxe™ Game PCB Assembly A036471-01 and -02
(a Figure 20 Asteroids Deluxe™ Game PCB Assembly Parts List
Part No. Description (Reference Designations and Locations in Boid)
C012294-01 Audio I/O N-Channel MOS/LSI Custom Chip (M7/8) 19-007 10K Ohm, + 20%, 114W &-Pin Dual-Inline-Package Resistor Network (RP1, RP2—use only if board has 74LS170s or 741.$670s at locations F3, H3, J3) 19-315103 10K Ohm Vertical PCB-Mounting Cermet Trimpot (R149, 152)
| 21-101104 | -1uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor | (C118-120) |
21-101153 015 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C30)
| 24-250105 | 1 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor | (C49, 50, 74, 83, 85, 103) |
| 24-250106 | 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C121, 122) |
24-250107 100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C17) 24-250226 22 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C104)
| 24-250477 | 470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor | (C72, 73) |
| 24-500475, | 4.7 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor | (C22) |
28-101100 10 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor (C87, 95) 28-101101 100 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor (C77) 28-101100 220 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor (C88, 89, 109, 110) 28-101271 270 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor (C46) 28-101391 390 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor (C75) 28-101680 68 pf Epoxy-Dipped 100V Radial-Lead Mica Capacitor (C106, 111)
| 29-006 | 1 uf, | +10%, 35V Tantalum Capacitor | (C21, 51, 116) |
29-088, -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C1-16, 18-20, 23-29, 31-44, 47, 48, 52-71, 76, 78, 79, 81, 84, 86, 90-94, 96-102, 105, 107, 108, 112-115, 117) 31-1N100 100V Type 1N100 Germanium Switching Diode (CR3, 4, 11) 31-1N914 75V Type 1N914 Silicon Switching Diode (CR1, 5)
| 31-1N4001 | 50V Type 1N4001 Silicon Rectifier Diode | (CR7-10) |
| 32-1N756A | 8.2V, +5%, Type 1N756A Zener Diode | (CR6, 12) |
33-2N3906 Type 2N3906 PNP Switching and Amplifying Transistor (Q1, 4, 5, 11-13) 34-2N3904 Type 2N3904 NPN 60V 1-Watt Transistor (Q2, 3)
| 34-2N6044 | Type 2N6044 NPN Darlington Transistor | (Q8-10) |
34-MPSA06S Type MPSAO6S NPN 80V 500ma Transistor (Q6, 7)
| 37-LM324 | Type LM324 Integrated Circuit | (P11) |
| 37-TLO82CP | Type TLO82CP Integrated Circuit | (A12, C12) |
| 37-4016B | Type 4016B Integrated Circuit | (R11, B12, D12) |
| 37-555 | Type 555 Timer Integrated Circuit | (N11) |
| 37-74LS00 | Type 74LS00 Integrated Circuit | (C5, N4) |
| 37-74LS02 | Type 74LS02 Integrated Circuit | (D5, P10. Also, for -02 PCB assy. only: C7) |
| 37-74LS04 | Type 74LS04 Integrated Circuit | (L4, R9) |
| 37-74LS08 | Type 74LS08 Integrated Circuit | (E5, K5, R6, B8) |
| 37-74LS10 | Type 74LS10 Integrated Circuit | (A8, N8) |
| 37-74LS14 | Type 74LS14 Integrated Circuit | (B5) |
| 37-74LS20 | Type 74LS20 integrated Circuit | (E4) |
| 37-74LS32 | Type 74LS32 Integrated Circuit | (M4, N5, B9) |
| 37-74LS42 | Type 74LS42 Integrated Circuit | (L5, E6, E8) |
| 37-74LS74 | Type 74LS74 Integrated Circuit | (D3, A6, R7) |
| 37-74LS83 | Type 74LS83 Integrated Circuit | (M5) |
| 37-74LS86 | Type 74LS86 Integrated Circuit | (P4) |
| 37-74LS109 | Type 74LS109 Integrated Circuit | (A9) |
| 37-74LS139 | Type 74LS139 Integrated Circuit | (L2, E3) |
[Continued on next page]
Figure 20 Asteroids Deluxe™ Game PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
| 37-74LS157 | Type 74LS157 Integrated Circuit | (F2, H2, J2, K2, F5, A10, B/C10, C10, D/E10, E10, F/H10) |
| 37-74LS161 | Type 74LS161 Integrated Circuit | (D6) |
| 37-74LS164 | Type 74LS164 Integrated Circuit | (P8, R8, K9) |
| 37-74LS174 | Type 74LS174 Integrated Circuit | (P68, D8, F10, N10) |
| 37-74LS175 | Type 74LS175 Integrated Circuit | (M6, P9) |
| 37-74LS191 | Type 74LS191 Integrated Circuit | (K4, C9, D9, E9, F9, H9, J9) |
| 37-74LS193 | Type 74LS193 Integrated Circuit | (F4, H4, J4) |
| 37-74LS244 | Type 74LS244 Integrated Circuit | (B1, C1, M9) |
| 37-74LS245 | Type 74LS245 Integrated Circuit | (P1,E2) Acceptable substitute is part no. 37-8304B |
| 37-74LS251 | Type 74LS251 Integrated Circuit | (J10, L10) |
| 37-74LS253 | Type 74LS253 Integrated Circuit | (P5) |
| 37-74LS259 | Type 74LS259 Integrated Circuit | (M10) |
| 37-74LS273 | Type 74LS273 Integrated Circuit | (F6, H6, J6, K6) |
| 37-74LS367 | Type 74LS367 Integrated Circuit | (HS, J5) |
| 37-74LS393, | Type 74LS393 Integrated Circuit | (B3, D4) |
| 37-74LS374 | Type 74LS374 Integrated Circuit | (L9,B10,D10) Acceptable substitute is part no. 37-74LS273 |
| 37-74LS670 | Type 74LS670 Integrated Circuit | (F3, H3, J3) Acceptable substitute is part no. 37-74LS170 |
| 37-7404 | Type 7404 Integrated Circuit | (B4, H10) |
| 37-7406 | Type 7406 Integrated Circuit | (N6) |
| 37-7497 | Type 7497 Integrated Circuit | (For -01 PCB assy. only: F8, H8, J8, K8) |
37-7805 +5V Voltage Regulator (VR3)
| 37-7812 | +12V Voltage Regulator | (VR1) |
| 37-7815 | + 15V Voltage Regulator | (VR4) |
37-7915 — 15V Voltage Regulator (VR2)
| 37-9316 | Type 9316 Integrated Circuit | (C3, C4, B6, C6, P7) |
38-MV5053, Type MV5053 Light-Emitting Diode (CR2) 41-3003 100 uH, + 10%, Hot-Molded Plastic Fixed R.F. Choke (L1-4) 62-001 SPST Momentary Pushbutton Switch (A5) 66-114P1T 4-Station Single-Throw, Dual-Inline-Package Bit Switch (M12) 66-118P1T 8-Station Single-Throw, Dual-Inline-Package Bit Switch (RS, L8} 79-42C24 24-Contact Medium-Insertion-Force Integrated Circuit Socket (01, E/F1, H1, J1, N/P2, R2) 79-42C40 40-Contact Medium-Insertion-Force Integrated Circuit Socket (C2, M7/8) 81-4302 Nylon Snap-In Fastener (VR1-4, Q8-10)
| 90-102 | 12.096 MHz, +.005%, Crystal | (¥1) |
90-6013 Microprocessor (C2)
| 90-7033 | Random-Access Memory | (L1, M1, M3, N3, P3, R3) |
02067001 Test Point 034602-01 Programmable Read-Only Memory (C8)
| 03590401 | Type 828131 Integrated Circuit | (For 02 PCB assy. only: F7, H7, J7) |
| 035905-01 | Type 828131 Integrated Circuit | (For -02 PCB assy. only: E7) |
| 036430-01 | Read-Only Memory | (D1) |
| 036431-01 | Read-Only Memory | (E/F1) |
| 036432-01 | Read-Only Memory | (H1) |
| 036433-02 | Read-Only Memory | (J1) |
Asteroids Deluxe ™/Cocktail
Figure 20 Asteroids Deluxe™ Game PCB Assembly, continued Parts List
Part No. Description (Reference Designations and Locations in Bold)
036799-01 Read-Only Memory (N/P2) 036800-01 Read-Only Memory (R2) 100015-103 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C45, 80, 82) 110000-102 1K Ohm, +5%, %4W Resistor (R27, 29, 45, 47, 72) 110000-103 10K Ohm, +5%, %4W Resistor (R9-26, 28, 33, 34, 39, 48-55, 67, 73, 74, 81-84, 86, 90, 92, 98, 102, 114, 117, 120, 121, 156, 159) 110000-104 100K Ohm, +5%, %4W Resistor (R69, 80, 146) 110000-121 120 Ohm, +5%, %W Resistor (R93, 126) 110000-122 1.2K Ohm, +5%, %W Resistor (R36, 160) 110000-123 12K Ohm, +5%, %W Resistor (R44) 110000-151 150 Ohm, +5%, “%4W Resistor (R68) 110000-183 18K Ohm, +5%, YW Resistor (R75, 143) 110000-222 2.2K Ohm, +5%, YW Resistor (R37, 46, 76, 116, 118, 122, 125, 145, 154) 110000-223 22K Ohm, +5%, YW Resistor (R1-8, 35, 42) 110000-270 27 Ohm, +5%, “W Resistor (R71) 110000-271 270 Ohm, +5%, /W Resistor (R88, 142) 110000-274 270K Ohm, +5%, %4W Resistor (R157) 110000-331 330 Ohm, +5%, %W Resistor (R30, 31, 115) 110000-332 3.3K Ohm, +5%, %W Resistor (R78, 147, 158) 110000-392 3.9K Ohm, +5%, YW Resistor (R40, 94-96, 148, 151) 110000-471 470 Ohm, +5%, 4W Resistor (R32, 97, 99-101, 103-111, 127-139) 110000-472 4.7K Ohm, +5%, YW Resistor (R38, 79, 85, 89, 91, 112, 123, 144. Also, for -02 PCB assy. only: R56-66) 110000-473 47K Ohm, +5%, %W Resistor (R43, 87, 155) 110000-562 5.6K Ohm, +5%, YaW Resistor (R41) 110000-563 56K Ohm, +5%, Y4W Resistor (R77, 113) 110000-680 68 Ohm, +5%, %4W Resistor (R70) 110000-682 6.8K Ohm, +5%, YW Resistor (R150, 153, 161) 110000-822 8.2K Ohm, + 5%, YW Resistor (R119, 124) 137108-001 Operational Amplifier Integrated Circuit (B/C12, E12) 137158-002 Type AM6012ADC Digital-to-Analog Converter (A/B11, C/D11) Acceptable substitute is part no. 37-AD561J (B11, D11) 137161-001 Electrically Alterable Read-Only Memory (N9)
79-441001 (Fuse Post) 034544.01 48-2017002 (Fuse Block Cover) 46.2019002 (Fuse) (Fuse)
034482-01 (Chassis)
A034623-03 (Power Supply Harn. Assy.) A035674-01 Volt. Plug Assy.) 79-3206 (Fuse Block)
782708 (Bushing)
78-70501SC* TOP VIEW (Bracket) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction foreidden without the 29-053 Specific written permission of Atan. Inc., Sunnyvale, CA. (Elec, Cap.) This drawing is only conditionally issued, and neither receipt nor Dossession thereot conters or transfers any fight i oF license to use, the Subject matter of the drawing of any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof, Except for manutacture by vendors of Atari, Inc., and for manutaciure under the corporation's. written license, no right to ‘eproduce this drawing ss granted or the Subject matter thereof unless by written agreement 142000-001 with or written permission from the corporation BOTTOM VIEW (Power Trans.) ‘A006555-01 (Rect. PCB Assy.)
A034630-01 -79-15021001 (RFI Filter Assy.) {Block)
A034629-01 (AC Harness Assy.)
Figure 21 Power Supply Assembly for X-Y Games A034561-03 E
Asteroids Deluxe Cocktail
Figure 21 Power Supply Assembly for X-Y Games Parts List
Part No. Description
A006555-01 Rectifier Printed Circuit Board Assembly A034623-03 Power Supply Harness Assembly, includes Shielded Power Transformer A034629-01 A.C. Harness Assembly A034630-01 PFI Filter Assembly A035674-01 Voltage Plug Assembly (set of four plugs) 29-053 26,000 uf 15V Electrolytic Capacitor 46-2013002 3-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse 46-2017002 7-Amp. 250V 3AG Slow-Blow Giass Cartridge-Type Fuse 78-2708 Nylon Type 6/6 Hole Bushing with 5/8-Inch Inside Diameter x 55/64-inch Outside Diameter x ‘%-Inch Thick 78-70501SC 2 Inch Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with %-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-01 Power Supply Chassis 034544.01 Fuse Block Cover 142000-001 Shielded Power Transformer
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 99-15038 CONFIDENTIAL: Reproduction forbidden without the 99-15001 thru 9915012 (ge7e for Button) specific written permission of Atari, Inc., Sunnyvale, CA (Ret. Button) Shis drawing ts only concitionally’ issued. and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the draw: ing or any design or technizal information shown thereon, nor any right to reproduce this drawing or any part thereof, Except for manufacture by vendors of Atari, inc., and for manufacture under the corporation's written license, no right to ‘eproduce this drawing is granted or the subject matter thereof unless by written agreement with or written permission from the corporation
99-15051 (Lamp Holder)
9815026 (Coin Inlet) u ~ 99-15040 (Lever) 99-15056 (Screw for Bezel) Ls
LWA 99-15025 ——>,/ | XOX 2 9915039 Coin iniet) s, 8 cA - \ (Bezel for Cover) ° . 99-15036
PART OF oN oe (Cover)
99-15041 . 9| _——_ 99-15055 - 99-15041 ° (Reing. Screw) f (Lockout Coil) SN Yor { 99-15053 Sey (Lockt. Coil Spring) < 99-15054 99-16027 NN (Pivot for Lever) (Coin Ret. Box)
+—— 99-15028 (Coin Ret. Box)
99-15037 (Sw. Adjuster) 99-15056 (Screw for Bezel) 99-15060 _— (Sw. Cover) A036597-01 (Harness—Not shown for clarity) 99-15029 (Bracket) 99-1! sow2— 8 (Switch)
Figure 22 Double Coin Acceptor/Mount Assembly A036693-xx A
On Figure 22 Double Coin Acceptor/Mount Assembly, continued Parts List
Part No. Description
A036597-01 Double Coin Acceptor Harness Assy. 99-15001 Coin Return Button with U.S, 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil (U.S. 25¢) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053, Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
1st printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm O Distributor
Address C Operator City State Zip U Other
City State Zip U Other.
Area Code Phone
No Postage Necessary if mailed in the United States
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA
POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086
eBpe siyy odes
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Seller warrants that its printed circuit boards and pars ‘thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games | Supplied with monitors) are free from defects in ‘material and) workmanship under normal use and service for a period of thirty
- days from. date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty | is expressed i in lieu of all other warranties expressed or ‘implied, including the implied warranties of merchantabil- } ity and | fitness for | a particular purpose, and of all other obligations or liabilities on the é ‘Seller's part, and it ‘neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
The use of any non- Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and | others. Be very. cautious in using non-Atari-supplied components with our games, in order to insure your safety.
may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor. 7 Atari distributors are independent, being privately owned and operated. In their judgment they
This document is and contains confidential trade secret information of Atari, Inc. This document is loaned under confidential custody for the sole pu,pose of operation, maintenance or repair of Atari equipment and | may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc. es he @ Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.