1942 (Capcom)
1942 (Revision B) (Capcom, 1984) · Manual · 20 pages · 18 sections · original scan
:
Before You Get Started. . .Stop!
Does your new game package include all listed parts? (Is it comptete?}
- Isthe game you have chosen to transform able to supply all the required voltages for the new game?
- Is the monitor configuration compatible? In most games it is rather difficult to change the monitor from a vertical mount to a horizontal mount. We recommend you choose a game cabinet with the same mount as your new game requires.
- Do you have the necessary tools? (See the recommended tool list)
Caution
F.C.C. Regulation Compilance
The PC. board cage supplied with this new game kit must be utilized and terminated to ground at the time of installation. This is to avoid radio frequency radiation and comply with the limits for a class “A” computing device pursuant to sub-part “J” of part 15 of FC.C. rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference
- in which case, the user at his own expense, will be required to take whatever measures may be required to correct the interference.
Installing and Servicing Your
New Game Package
Table of Contents
New Game Package Contents.........5- ae fe xt dot piu 6 a 4 ie & 3
Power and Monitor Requirements .. 0.6... 6c eee eee eee eee 3 Recommended Tools and SUPDIES isa © sc0s0 v cece eanase mutase sername emrAaTacemne oats 4
DIDS WICIRTADIES: as a sect oan 9 a Oe CE ee De co EE see Soa Y OF 4
Game Operation wie i ies i 5 uae FT 6 Hiss Waa DEATOS TS HE TES ETA EE 6
Installation Procedures... 66. eet 7
DidQnostics:ancAGJUStMENtS: «ars cacao o retnw nad & clans ate & cine w 5486 Foes 4 12
Control Panel Positioning ...... 6... cece eee eee eee ee eeeee 16
Main Harness Connections ........6. 0 0c e eee eee eee eee inside back cover
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Jet
NEW GAME PACKAGE CONTENTS
1 Main Printed Circuit Board (PCB) 1 Marquee 1 PCB Cage (FCC Required) 1 Control Panel Overlay 1 Set Legs, Bolts, & Spacers 1 Plex Control Cover 1 Connecting Wire Harness 1 Set Side Graphics 1 Eight-Way Joystick 1 Set Play Instructions & Function Labels 4 Player Button Assemblies 1 Service and Installation Manual
POWER REQUIREMENTS MONITOR REQUIREMENTS
+5 VDC 5 amp Vertical Mount Raster Scan +12 VDC 1 amp Negative Composite Sync
Recommended Tools and Supplies
ROMSTAR new game package. Phillips and Slot Screwdrivers Socket Set Enthusiastic Attitude Wire Cutters and Strippers Pliers or Channel Locks Planning and Careful Thought Electric Drill 3/32” © 1/4” © 7/16" Drill Bits 1/4" Plex Bit 1-3/16” Chassis or Sheet Metal Punch 1 1/4” Plex Hole Saw Glass of Water and a Snack Small File Razor Knife and Sharp Blades Straight Edge Patience Common Sense
Dip Switch Tables
Optimize Your Profits Painting Supplies (if you do your own painting) Paint Brush and Paint (don’t forget the primer) Paint Roller and Pan Sand Paper Putty Knife and Wood Putty A Good Night’ Sleep Staple Gun and Staples Soldering Iron and 60/40 Resin Core Solder Vacuum Cleaner Assorted Fastening Hardware Shrink Tubing: 3/32” © 1/8” © 3/16" Masking Tape 3 112" OR 4” Wire Ties Spray Window Cleaner and Rags (baby diapers work GREAT!)
Thorough Research shows that two and a half minute games both satisfy players and also keep the quarters flowing. If games aren't running about two and a half minutes long, then collections probably aren't at their peak. You'll want to tailor your game to your location. The trick is to adjust a few DIP switches. (See the chart in this book.) It’s easy!
Game Adjustments Use the Dip-Switch Banks. Game adjustments are made with DIP-switch bank Aand DIP-switch bank B on the CPU board. Select your options from the Dip-Switch Table in this book. Then turn the game off. For each new setting, you'll have to change the position of one to three switches ona single DIP-switch bank. Use a pen or small screwdriver to operate the switches. Now for the multiple-choice section. Choose one or more: ¢ Forashorter game, increase the scores at which players achieve bonus points. ¢ For a longer game, reduce these scores. (Use DIP-switch bank A, switches 3 and 4.) © Fora shorter game, raise the difficulty level. For a longer game, reduce it. (Use DIP-switch bank B, switches 2 and 3.) Customize game pricing to suit your location. (Use DIP-switch bank A, switches 6 through 8.)
Dip-Switch Bank A
Numbers of
planes
30,000/100,000/over 100,000
30,000/80,000/over 80,000
20,000/100,000/over 100,000
20,000/80,000/over 80,000
Upright Table
Free Play 1 Credit - 4 Coins
1 Credit - 3 Coins
3 Credit - 2 Coins
1 Credit
4 Credit
2 Credit
1 Credit Recommended Settings Lon | off J oft [oft Jon | off | off | oft |
Dip-Switch Bank B
Adjustment Portrait
Normal
Very Difficult Difficult Difficulty
Coin 2 Same as Coin 1
Reverse Picture Normal
Reverse
Test Mode
off Recommended Settings
Game Operation
Buy-In Feature. After completing a game, players are invited to “buy in” or continue where they left off. Continued games are more challenging than original games. So continued games tend to involve skilled players at the level they prefer and to increase collections. To buy in, a player inserts his next coin while “CONTINUE GAME” appears on the screen. Then he holds the fire button and Pushes start.
Playing Tips Points depend on the percentage of enemy planes destroyed. (Bonus points will be different if a player’s plane is on an aircraft carrier.) Example: 90% .......e cece eee ences 10,000 Points Loops. In any wave the player can only loop three times (number of loops is displayed on the bottom of the screen). The number of loops adds bonus points when the player returns his plane to the aircraft carrier. Example: 1 LOOP...... esse eee e eee eens 1,000 Points
Extra Power. If the player destroys all enemy planes of one color, POW ap- Pears on the screen. Touching the Power Unit gives the player an advantage that depends on the color of planes shot down... Green Planes..........++ Player’s plane becomes a 4-shooter Yellow Plan€S «1... cece eee e eee One loop is added Orange Planes... .Enemy plane stops shooting for 15 seconds White Planes .........0.06. All enemy planes are destroyed Gray Planes.... . . Shield is added to player’s plane Black Planes .. 72: . Player's squadron gains a plane Red Planes... 0. ccc cee eee eee e ee eeeee Points
When a player destroys a complete red-enemy squadron (all planes of one color), POW appears on the screen. When a player destroys the heavy bomber, the bomber wave ends. At the end of the game the screen indicates the number of enemy planes shot down and the percentage destroyed. If a player destroys all enemy planes of the red color, POW appears on the screen. However, if an enemy plane shoots down the player's aircraft, the enemy squadron under attack (all planes of one color) return.
Installation Procedures
Something To Think About Your final product will be anew game. You have made a wise decision to transform a game that has seen better days in the all important cash box into a new game. This is by far the most cost effective alternative to maximize the return of your initial investment. All you provide is the cabinet with a power supply and a monitor. Oh yes, you will need a touch of elbow grease. And that’s it! We provide the rest. The end result is... anew game at a very low cost. Fact: Spend alittle time on the cabinet’s appearance (i.e. marquee, control panel and cabinet graphics). With a little paint, some wood putty and new lights, you will raise the profits of any game. . .especially with the introduction of anew game Package. The mew game look should always apply to the inside of your game as well as the outside. A few wire ties and shrink tubing on your harness; some fastening hardware on your subassemblies and a sweep with the ol’ vacuum cleaner will ensure that unnecessary glitches do not occur. Remember: You are creating anew game . If you have any questions or just need some advice on any of your new game transformations, don’t hesitate in giving a member of our technical staff a call.
Let’s Get Our Hands Dirty
Preparing the Original Game for the New Game Remove the following:
| 1, | Main logic board(s) | 4. | Monitor Bezel |
| 2. | Control panel | 5. | Marquee |
| 3. | Monitor plexiglass | 6. | Graphics |
| would recommend painting your cabinet to give it a fresh new look. (If it is geographically inconvenient to make use of our facilities, you may consider having an auto body shop take care of your painting needs.) If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with lacquer thinner. If you intend to use your original plexiglass, be sure it is in mint condition or it should be replaced. Thoroughly clean out your cabinet.
Time To Install Your New Goodies
Before You Start. . .Remember DO NOT Do This Work With The Power Onl
Logic P.C.B. Cage Mount the logic cage securely (away from power supply}. A Mark and drill pilot holes (3/32”). B Place the logic cage (bottom) over the holes and secure it with the supplied wood screws. C Instat! the P-C.B. into the logic cage. Use feet and spacers supplied and adjust them so that the screws will go through the slots int he cage bottom.
Wire Harness
Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Even if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.
Connecting the Wire Harness to the Existing Wires When you hook up the contro! panel, power supply, monitor or other subassembliés that remain in the game cabinet to your new wire harness, try and use their existing secondary connectors.
- Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.
- Solder the new wire designated for that position to the original wire you just stripped.
- Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble.
- Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is a new game , not a sloppy conversion.
Power Wires
- Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.
- You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary). This will help to ensure that you don’t overload the edge connector pins and cause them to “burn”.
Monitor Wires
You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires.
Speaker Wires Find the two wires that are designated for the speaker and hook ‘em on up.
Coin Door Wires
Connect the designated wires to the coin switches and meter.
- Youcan connect your door lamps to the unused —5V power supply. Some games have separate power outputs for the coin door lamps.
- Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in.
GUESS WHAT?
You are almost done with the electrical connections of your new game. All you have left is the control panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. W/hen you return, we can take a fresh look at your progress and then move forward.
Smoke Test
What Test?
Don't worry. All this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.
- Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
- Make sure the logic board, board cage, monitor and power supply are securely fastened in place.
- Double check the connectors to be sure they are wired and connected properly.
- Set the dip switches on the logic board to the factory recommendations. (Refer to page 5.) Also, be sure you set the dip switches for “DEMO W/ITH SOUND”. This will enable you to hear as well as see that your new PC.B. is functional.
Time to Apply Power: 1. Look and smell for smoke. (TURN OFF IMMEDIATELY IF ANY IS NOTICED) Listen for game sounds. If after one minute you have not heard any sounds: A) Check for proper dip switch settings. B) Adjust volume control and check speaker connections. C) Check the +12V power supply to the logic board.
HORIZONTAL SYNC INPUT FROM PCB. (OR COMPOSITE SYNC INPUT) HORIZONTAL SYNC OUTPUT TO MONITOR (OR COMPOSITE SYNC OLITPLUT) VERTICAL SYNC INPUT FROM PCB.
VERTICAL SYNC GUTPUT TQ MONITOR 4 "1 TALSO4 sf 10 ISED
NOT USED <<
B) Now how’s your picture? © It it centered? ® Is it too bright or dim? © Is it in focus? Check your monitor manual for these adjustments. If your screen looks “off”, then your new game transformation may have been in vain. So let’s take the time to make the monitor look great. C) Is the picture upside-down? Dip switch 4 on switch bank ‘’B’” should solve your problems.
Control Panel Assembly
1,
Zz
ON Remove the buttons, joysticks and wire harness and put them aside fro now. Do not remove the original panel overlay until the new holes have been drilled. Mark positions on the panel for the new holes as specified on page 16. ROMSTAR supplies a clear 1/8” thick piece of plexiglass with every new game package to cover the control panel. We feel that yournew game investment is well worth protecting. . .and the control panel is the first place to show wear and tear. © You will need to cut this piece to size. Use the control panel as a template. © Use a razor knife to score the plexiglass deeply. Then use a pair of pliers to break away the extra plexiglass. Now drill the holes in your panel that you have marked off for the buttons, Joystick and bolts. Hint: For best results, use a chassis or sheet metal punch for button holes. Drill the same holes on your plexiglass panel protector. Once again use your panel as a template. Hint: To avoid chipping while you are drilling the holes, place the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hole cutter. The holes are now all cut. Smooth them out on your panel and plexiglass with a fine toothed file. Remove the original graphics overlay from the panel. Clean up the panel and install your ROMSTAR graphics. Make It Easier: Peel the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. Vo bubbles please. Now peel off the bottom half and do the same as you did for the top. Adhere the instruction and function labels. Install the Plex Control Cover over your completed new game panel.
Marquee Installation
Using the original marquee as a template, Center your mew game marquee graphics and score the new marquee deeply to fit the cabinet. Break off the excess with pliers. Be sure the light behind the marquee works. Everything should always work on a new game. Take your time ... Don’t forget this is going to be a new game.
Side Graphic Installation
Be sure sides of game are clean and free of old adhesive, dust, etc. Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet). Peel off top 1/4 of decal backing and apply to cabinet with a smoothing motion (use a soft rag). Continue peeling off backing and smoothing. Remove any small bubbles with a pin or razor blade (pop them!)
Finishing Touches
1. Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware. Make sure the coin door is tight and the coin mechs are well adjusted. A game is no good to anybody if you can't get a coin into it. Once again go over every step of this mew game transformation in your mind. Be sure everything is correct and to your liking. Power up the game. A. Check all the coin switches. (Does the coin meter work?) B. Play your new game . ¢ Are all the player controls working? e Are the game sounds present? ¢ Is the volume level proper? e Are the dip switches set properly? Well, that’s about it. Good Luck.
Diagnostics and Adjustments
Your game includes a Diagnostic Mode that checks operation and helps you make adjustments to insure optimum performance. Entering Diagnostic Mode. Turn the game off. Use a pen or small screwdriver to turn on DIP-switch 5 of DIP-switch bank B on the CPU board. The machine will start in the Diagnostic Mode when you turn it on. Diagnostic Mode consists of eleven independent tests.
RAM CHECK
| ADDR | WR | RD | Loc | ||
| W-RAM 1 | = | -OK- | == | ** | NO9 |
| W-RAM 2 | = | -OK- | al | “* | NIO |
| C-RAM | = | -OK- | = | 2% | bo2 |
| S-RAM | = | -OK- | s? | =* | AOo9 |
Lever = Next
Figure 1. RAM Test
- Ram Test
The RAMs are automatically checked before the other ten tests start. When a RAM error is detected, the display identifies the bad RAM with NG instead of OK. (Of course power, buss or clock problems may cause a good RAM to appear bad.) Tests can’t proceed if all RAMs don’t check OK. After the RAM check is over, move the joystick to display the test menu.
o1
F: EXEC
Test Method TEST MENU INPUT OUTPUT HARD COLOR SOFT COLOR: CHAR SOFT COLOR: SCROLL DOT CROSS HATCH CHAR SCROLL OBJECT SOUND
Figure 2. Diagnostic Menu
The next ten tests are performed using the joystick lever and the FIRE (F) button. A status message appears at the bottom of the screen...
F: FIRE Button
JOYSTICK...
RT. To increase numbers displayed on the screen, move right. LT: To decrease numbers displayed on the screen, move left. EXEC: A test is being executed. END: The test is concluded. LEVER & F: You're using the joystick and FIRE button simultaneously.
The Red Symbol is the cursor. Use the joystick to move the cursor beside the desired test. Now push FIRE.
- Input Test
Tests 2 and 3 help you evaluate the game's |-O port. Test 2 lets you see if switch operation is being recognized by the computer. When you press a switch, a 1 should be displayed (among the zeros on the right half of the INPUT TEST screen). \W/hen that switch is released, a O replaces the 1. Similarly when a DIP switch is ON, a 1 should be displayed and when OFF, 0 should appear.
- Output Test Check the outputs. Move the cursor and set any bit on or off by pushing FIRE. Look for stuck bits. (D1 and DO of address C806 can’t be changed since they're permanently set to 1.)
- Hard Color (Monitor) Test “Hard color’ refers to your game’s hardware. Of course your game’s hardware for displaying colors is the monitor. That’s what this test helps you check. Colors are displayed. Do you like what you see? If so, go ahead to the next test. Otherwise it’s time to adjust your monitor's screen, black-level, cathode-drive and cutoff controls. You can use test 7 (crosshatch pattern) for the rest of your monitor-setup chores.
- Soft Color (Character) Test The soft (software) color test examines your video RAMs by displaying characters. Missing or incorrect characters may indicate a bad video RAM. Other Chips that share the same address or data buss as your video RAMs may also cause character malfunctions. In addition, bad clock signals that normally enable (CE, WE, etc.) strobe or select (CSI, RAS, CAS, etc.) RAM functions might cause a good RAM chip to malfunction. Use your Logic Probe and check the neighborhood of the suspected RAM for missing logic pulses.
- Soft Color: Scroll (ROM) Test This test displays the scrolling colors. Check for missing or incorrect colors. If you find a malfunction, suspect a bad ROM (but don’t forget to check buss and clock signals used by the ROM).
- Crosshatch Screen
The crosshatch screen helps you to optimize your monitor's purity, linearity, focus, and convergence. Picture size and position can also be tweaked while you're displaying this screen. Push FIRE for the next test.
- Character Test
This test displays the game's character patterns. Check for missing characters. If you find a malfunction, suspect a bad ROM (but don’t forget to check buss and clock signals used by the ROM).
- Scroll Test
This test displays the garme’s scrolling patterns. If any pattern is missing, suspect a bad ROM (but don’t forget to check buss and clock signals used by the ROM).
- Object Test This test displays the object patterns used in this machine. If any pattern is missing, suspect a bad ROM (but don't forget to check buss and clock signals used by the ROM).
- Sound Test
You can make adjustments to the sound effects with this test. Also, if your sound section is malfunctioning, this test helps you locate the problem. Choose options 00 through IF by moving the joystick. Listen for incorrect missing or duplicated sounds. A. If all sounds are incorrect , the problem could be a bad RAM or ROM. B. If all sounds are missing, the problem could be analog. . .
- leaky electrolytics that normally couple audio signals to the speaker; 2.a bad power-amplifier chip (last IC before the speaker);
- AC or incorrect DC voltages on amplifier-power pins C. If all sounds are missing, the problem could also be digital. . .
- suspect a bad D-to-A converter,
- a bad crystal, 3.a bad sound-microprocessor,
- or a bad chip (buffer, PIA, etc.) that handles date or addresses. D._ If only a few sounds are missing or duplicated, suspect a digital problem such as open or shorted sound-select (address) lines.
Here are your SOUND-TEST options. . . Disables sound effect 01, OF, 11, 12, 15-19 and 1A 01 B29 propeller ON (Use FIRE to enable) 02 B29 explosion 03 Ricocheting enemy bullets 04 Enemy plane exploding 05 Player's firing sound 06 Player's circling sound 07 Sound when taking a POW 08 Sound when player receives a bonus plane 09 Typewriter OA Coin-insert sound OB B29 propeller OFF OC Player's propeller OFF OD Player's plane taking off OE Player's plane landing OF Player's propeller ON (Use FIRE to enable)
Entering Game-Over Mode 1A
1B IC 1D 1E IF Music OFF Background music Starting music Bonus wave music (at beginning of wave) Background music when heavy bomber appears Bonus-wave clearing music Game-over music 6th-place and under music Top-score music 2nd to 5th-place music Starting music when heavy bomber appears Typewriter ringing-sound Unused Unused Unused Unused
When you desire to end the Test Mode, turn the game off. Now set DIPswitch 5 of DIP-switch bank B to OFF and power up.
16 8 WAY JOYSTICK
LOOP FIRE FIRE * LOOP
POSSIBLE 1 & 2 PLAYER LOCATIONS Control Panel Positions
PCB Layout
1942 MAIN HARNESS CONNECTIONS
Solder Side Parts Side GND
Black GND Black Black (—) Speaker Black
White (+) Speaker White
Black (—}) Coin Counter
Fea [Down _|
Right 1 P
Shot 2 P Up 2P Orange Green Down 2 P Left 2 P Yellow Right 2 P Black 2 Player Start Black 1 Player Start Black
2 P Loop Blue Grid (Video} Black Red (Video) Red Blue (Video) Blue
GND Black
2 P Connections for Cocktail Only (Except 2 P Start} Black
Violet Gray White
White Service Switch
not used not used not used 8 | [0 | [| F
LK [M | LN | LP | | __ Right 2p R |__2 Player Start__| | |__1 Player Start | T | |__Coin switch | U | |__ Service switch | v | | __notused |W | | notused | X | Y Ese a | |» | [a | fe | Sync {Video} Green not used } not used not used +5V a
| 4 | | 6 | [7 | [8 | | 9 | [10 [|
[14 | 15 | | 16 | [18 | [19 |
27.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.