Moon Cresta Operating Instructions and Service Manual (420-0518)
Moon Cresta (Nichibutsu) (Nichibutsu, 1980) · Manual · 29 pages · 20 sections · original scan
[MOON
CRESTA
Owner’s Manual
M I p N oe BY anual Part No. Cre mlin/SEGA 420-0518 ny i
MOON CRESTA.
Operating Instructions
and
Service Manual
MOON CRESTA OWNER’S MANUAL Copyright © 1980 by GREMLIN®/SEGA®, All Rights Reserved
table of contents Introduction .....0..00. 00000 c eee 1
introduction
This is an electronic game that makes extensive use of digital integrated circuitry and television monitor circuitry. This manual assumes the maintenance technician possesses a general knowledge of solid state circuitry, microprocessor, TTL digital integrated circuitry and T.V. monitor concepts. Any individual not knowledgeable in these areas should not attempt repair of the electronic portion of this game. It should be noted that any attempt to repair the game in the field without the express consent of the factory will immediately void the warranty!!!
important notes
An important service note is posted in this game and is repeated here for emphasis:
If at any time the T.V. screen shows a meaningless display or the game otherwise malfunctions, simply drop a coin into the coin mechanism. This should correct the problem. If not, the game requires service.
The circuitry in this game has been arranged so that the insertion of a quarter through the coin mechanism will reset the restart in the system. This clears up temporary problems caused by power line disturbances, static, etc.
SERVICE TECHNICIAN NOTE:
The system reset circuitry described above requires that the coin counter is attached to the system. If there is a coin counter problem and no replacement is available, the game will function properly if a 10K Ohm resistor is connected across the coin counter input pins to the video logic board.
also
Never replace any components with anything other than exact replacement parts. (See Parts list located on Service Schematics.)
Never remove circuit board connections while power is on.
Do Not replace the fuse with anything other than the proper value. A blown fuse indicates an overload condition within the game. Replacing the fuse with a higher value can cause severe damage to internal components if an overload occurs.
Always consult the manual before attempting repairs.
Correspondence regarding this game should be addressed to:
GREMLIN/SEGA 8401 Aero Drive San Diego, California 92123 (714) 277-8700
game concept
Gremlin/Sega “MOON CRESTA” is a one or two player game in which players may compete for highest score against the game computer. Each time a player is hit by an alien, the game switches to his opponent's sequence. The object is to destroy as many of the descending aliens as possible. To accomplish this, the player is given a three stage multi-fire Warship. He begins with the first stage, firing a single laser at the enemy. If he is successful in eliminating the first four sets of aliens, he is given an opportunity to dock his first stage onto the second within a specific time limit (the sooner he unites the stages, the higher is his awarded score). Once docked, the stages combine their firing power, so the first (one laser) adds to the second (two lasers) giving the player a total of three usable lasers as the game continues. The player then must face two more sets of aliens and a shower of meteors, after which he has a chance to dock again, this time uniting with the third stage for a combined fire power of five lasers. If he is able to defeat the last two sets of aliens intact, the entire sequence begins again. The game continues with increasing difficulty until the entire warship is destroyed. When the warship is hit the layer continues with whatever stages remain. If his score reaches 30,000 he is awarded a free game and his score continues to accumulate.
options selection
Your Moon Cresta game is equipped with a set of switches that allows you to determine the charge per play. The switches are located in the upper left corner of the logic board.
Coinage | Switch Position 1 2 3 4 5 6 |
| 1 coin/1 play | off | off |
| 2 coin/1 play | on | off |
| 3 coin/1 play | off | on |
| 4 coin/1 play | on | on |
Switch adjustments must be done with the power off. Switches are set at 1 coin/1 play when machine is shipped.
transformer voltage conversion instructions
To convert the game transformer to 100, 115, or 230 VAC, refer to the following chart:
For 100 volts: Connect the voltage INPUT lines to transformer terminals 1 and 2.
For 115 volts: Connect the voltage INPUT lines to transformer terminals 1 and 3.
For 230 volts: Connect the voltage INPUT lines to transformer terminals 1 and 4. The fluorescent lamp line must be connected to transformer terminal 3,
ALSO, THE TV MONITOR MUST BE CONVERTED TO THE SAME VOLTAGE INPUT AS THE GAME TRANSFORMER. REFER TO THE MONITOR MANUAL IN THE GAME.
repackaging instructions
Should it be necessary to ship this game, follow the instructions below for game recrating:
A) If the original shipping bolts have been discarded (Ref. 1), obtain four 5/16-18 x 1 3/4” hex head bolts with 5/16” flat washers. Carefully lay the game on its side and attach skid (Ref. 2).
B) Place game upright. Tape game keys to upper flange of operator's panel (Ref. 3). Crate the game using appropriate shock-absorbent packing material (Ref. 4). Include padding on all four corners of the game (Ref.. 5). After crating is completed, secure package with strapping (Ref. 6).
maintenance and troubleshooting
procedures
Always check and confirm the following items when it is believed that a problem has developed. These items are relatively simple but commonly overlooked.
1. 2.
AC Junction Box Is the power switch on? Are all fuses intact? One fuse is located directly on the bottom of the AC junction box and three others are located in a fuse block directly behind the transformer and to the left of the logic board when looking in from the rear. If a fuse blows out after being replaced, it indicates trouble in another component. Always replace with the prescribed capacity fuse, as normal equipment may be damaged if larger fuses are used as a substitute.
Fuse Block
2A Transformer Fuse
. Are the connectors firmly inserted? Poor connector connections must be considered for any indication of trouble. Check all related connectors for poor contact. Although disconnected connectors are easily spotted, poor contacts are difficult to locate. The connectors should therefore be pushed in firmly and then loosened to spot poor connections. When testing the PC board connectors, always turn off the power. . Turn power supply off and on again. As the unit may return to normal if the control circuit is reset when the game seems abnormal, turn the power off and on to see if the trouble will clear up. . Are there any metallic objects on the PC board? Ensure that there are no metallic objects on the PC board, as this will cause shorts in the system. Also refrain from putting other objects inside the cabinet. . Ensure that all eproms are firmly seated in the logic board.
The following instructions will help you trace down and find most problems. The procedures are listed by the more common kinds of problems that could arise. Read through all the steps first, then implement them one at a time. You will need an AC/DC voltmeter and an oscilloscope.
NO PICTURE—TV TUBE AND FLUORESCENT LAMP ARE OFF.
- Plug the game in and check to see that it is receiving 115 (230) VAC. Measure 115 VAC at the input terminals of the game transformer. If it is not present, proceed to next step.
- Check fuse located on the bottom of the AC junction box. If it is good, proceed to next step.
- Remove the cover of the junction box. Measure 115 VAC on the output of the EMI filter. If it is not present, the EMI filter may be bad or one of the AC line connections in the junction box may be loose. Unplug the game and re-check these connections.
- If the fluorescent lamp still does not operate, turn the game off and then turn it on again. This usually re-starts the lamp. If it doesn’t, turn the lamp in its socket. This will re-seat it for a better connection. Sometimes the lamp works loose during shipment.
NO PICTURE—TV TUBE AND FLUORESCENT LAMP ARE ON. SCREEN BLACK
- First make a quick check of the monitor-to-logic board connections. Are all wires making contact with the pin connector? Are the wires secure on the monitor plug-in connector?
- Check 5C, 6F and 6H on the main logic board for proper video timing signals.
SCRAMBLED PICTURE OR LOSS OF VERTICAL OR HORIZONTAL HOLD.
- Check sub board A and sub board B to ensure that they are properly seated. If they are loose or ajar, it will cause a scrambled picture.
- Check the wires on the 6H modification to ensure they are not broken. Bottom wire controls vertical synchronization and top wire controls horizontal synchronization. Refer to drawing 800-3110.
SOUND PROBLEM OR NO SOUND.
- Check wires running from VR to edge connector to ensure they are intact.
- If they are not broken then check 11A.
INCORRECT POWER SUPPLY
- Check D4, D5, IRI and IRII. Replace if necessary. All voltage is at +5V except 10L and 11A which uses 7V DC.
GAME DOES NOT COIN UP. 1. Acommon problem with a game that does not coin up is that the coin switch trip wire is out of adjustment. Usually, all that is necessary is to bend the trip wire up or down, depending on whether a heavier or lighter tension is needed. . Don’t overlook the possibility of an incorrect or faulty coin switch-to-logic board connection. Sometimes these wires work loose from the coin switches. . Check main logic board—resistor packs 1 or 2 may be bad and need to be replaced. Also Check 9E.
PLAYER CONTROLS NOT WORKING. 1,
2.
3. Check first to be sure all control switch connections are secure. This includes checking the black ground wire leads. If these connections are good, make sure the control panel leads are intact inside the connector to the logic board. Check the main logic board—the 3 jumpers illustrated in detail B of drawing 800-3110 may have broken loose. Also check 9E.
recommended spare parts single games
Gremlin Part # Description pariantities
| 130-0001 | speaker | 1 | |
| 130-0002 | speaker cover | 2 | |
| 200-0019/21/22 | color monitor | 1 | |
| 220-0035 | lock (coin door) | 2 | |
| 220-0066 | coin mechanism | 2 | |
| 240-0007 | black button | 5 | |
| 240-0009 | yellow button | 5 | |
| 250-0034 | spring retainer | 5 | |
| 250-0285 | front cash door | 1 | |
| 253-0104 | panel monitor | 1 | |
| 253-0192 | panel logo M/C | 2 | |
| 253-0193 | contro} panel graphics | 1 | |
| 390-0011 | fluorescent lamp | 1 | |
| 420-0515 | interior graphics | 1 | |
| 420-0518 | manual M/C | 2 | |
| 510-0016 | slam switch | 1 | |
| 510-0023 | WICO switch assembly | 5 | |
| $14-0025 | 2A fuse | 5 | |
| 514-0053 | 5A fuse | 5 | |
| 514-0054 | 4A fuse | 5 | |
| 560-0054 | game transformer | 1 | |
| 230-0023 | 18.432 MHZ crystal | 3 | |
| 482-0101 | 2SD553 transistor | 3 | |
| 482-0102 | 1SA1015Y | 2 | |
| 481-0073 | diode 3BZ61 | 3 | |
| 313-0035 | UA 78MGUIC IC | 3 | |
| 316-0751 | eprom 171 | 1 | |
| 316-0752 | eprom 172 | 1 | |
| 316-0753 | eprom 194 | 1 | |
| 316-0754 | eprom 195 | 1 | |
| 316-0755 | eprom 196 | 1 | |
| 316-0756 | eprom 197 | 1 | |
| 316-0757 | eprom 198 | 1 | |
| 316-0758 | eprom 199 | 1 | |
| 316-0759 | eprom 200 | 1 | |
| 316-0760 | eprom 201 | 1 | |
| 316-0761 | eprom 202 | 1 | |
| 316-0762 | eprom 203 | 1 | |
| 314-0118 | TALS 366 | 2 | |
| 315-0046 | 2114 RAM | 5 | |
| 314-0092 | 8216 | | | 5 |
| 312-0013 | 2101 RAM | 5 | |
| 314-0119 | 74LS 377 | 2 | |
| 315-0041 | Z80A | 1 | |
| 315-0045 | 4066 IC | 3 | |
| 313-0033 | MB3713 | 3 | |
| 313-0032 | TD62064 P | 3 | |
| 313-0034 | LM324 | 3 | |
| 315-0066 | 93425 | 4 | |
| 314-0099 | 74LS 245 | 2 | |
| 514-0001 | 2A fuse (AC junction box) | 5 |
BLOCK DIAGRAM: Refer to schematic for parts that make up this diagram.
7. . 1E, 1D, 3C . Crystal, 18.432 MHZ
- AO through A15 on Z80 CPU; buffered by 7D, 7E, 8D . DO through D7 on Z80 CPU; buffered by 8H, 8F . 2114: 3H, 3F, 7N, 7P Qua PWN
10. 11. 12. 13. 14, 15. 16. 17. 18. 19. 7B
2101: 4F, SF 93425: 1N, 1P, 1R, 1S, 1T . All Eprom . 6H, 6], 4E, SE, 2E, 3E, 2F 8D 8P 8N, 8M, ON, 5R, 4R, 5S, 4S, 5P 9D, YE, 9F, 9C OR, 8R, 8S, 8T, 9], 9M, 6T, 7T, 7S, 9L 1A, 1B, 2A, 2B, 2D, 6N, 6H, 6B, 6F, 3S, 3R, 5B All Eprom 2H, 2J, 2K, 2L, 1U, 3L 6M, 6L CRT (monitor) Control Panel
input strobe output strobe 4h 3 14 | VIDEO TIMING | _ LOGIC
CLOCK 2 CPU memory CRT beam peal
TY address <¥ position addr. anking ul address bus _4 ADDRESS MULTIPLEXER 8 U y 4 ' ! 1 READ- | 6 | READ- | 7 _ | REFRESH SHIFT |_|-=| VIDEO | 4, WRITE ONLY MEMORY | 19 16 |REGISTER COMBINER
MEMORY MEMORY ICONTROL 7
Vv ory VIDEO 280A REFRESH 9
MEMORY ' (READ-WRITE) CHARACTER data bus GENERATOR
(8 lines) Ub MEMORY 15
(READ-ONLY)
!
| TIMING & 72 | pur | 7? lourrut| 7? 18
CONTROL PORTS PORTS
LOGIC ready a
player controls
mem R 19 +V sound indicators mem W
Attach edge connector here. Lettered row of edge connector faces up.
Reset Switch Selection Switch Top of Board View
anne *
PART NO Gremiin industries, Inc. San Biege, California 92123 PARTS |TITLE ASSY, TOP LIST GAME, MOON CRESTA UPRIGHT QTY PER ASSY DESCRIPTION REF DES
130-0002 SPEAKER COVER
140-002 | COVER J BOX
140-0049 CABINET DIRECT WOODGRAIN
250-0032 FRAME BEZEL
250-0034 SPRING RETAINER
250-0038 MOULDING STRIP
250-0048 CLIP SWITCH
250-0356 BRKT COLOR MONITOR
250-0430 GROUND STRAP UPRIGHT
293-0104 WINDOW GLASS
253-0192 PANEL LOGO M/C
280-0004 CLIP WIRE, HOLD-DOWN
130-0001 SPEAKER, GAME 6x49
280-0064 SPCR 3/8" LNG PVC
390-0019 LAMP, FLOR 18 INCH
420-0028 DECAL S/N
420-0030 DECAL CAUTION HSV
420-0040 DECAL, RECYCLE
420-0041 DECAL, S/N_ SMALL
420-0507 (NHI)
LIGHT BAFFLE UPRIGHT 6M
420-0515 GRAPHIC INT, CENTER M/C
420-0516 420-O05\7 GRAPHIC INT. RIGHT M/C
420-0518 GRAPHIC INT. LEFT M/C : |
MANUAL M/C
Gremlin Industries, Ine.
TE NO San Diego, California 92123 PART NO OTY PER ASSY LIST PARTS [TITLE ASSY 10P _ GAME, MOON CRESTA TOO-0030 |sh3} A UPRIGHT DWG NO OF 7 | REV DESCRIPTION REF DES
420-0519 COVER, FUSE BLOCK
514-0025 FUSE 2A SLOW BLO
514-0052 FUSE BLOCK
514-0053 FUSE 5A SLOW BLO
514-0054 FUSE 4A FAST BLO
3) 800-0136 ASSY, HARN SPEAKER , UPRIGHT
800-0130 ASSY POWER XFMR
800-0147 ASSY, FLORESCENT LAMP 2
800-0135 ASSY, MECHANICAL COIN MECH
800-0140 ASSY, MONITOR CLR 19" VERT
800-3104 +1}. ASSY HARN MASTER M/C
800-3105 TT ASSY CONTROL PANEL M/C
800-3110 ASSY GAME ELECTRONICS M&
800-0145 ASSY A.C. JUNCTION BOX
420-0526 MANUAL ELECTROHOME MONITOR CVERTICAL MOUNT )
4\ 420-0132 LBL PRICE 25¢
800-0142 ASSY, GROUND STRAP 12"
320-0020 SEALANT, FOAM
A4 280-0324 CABLE CLAMP, NYLON SCR. PHL. RD. HD. #6% 2 7SHT. MIL. SCR. PHL. RD. HD. #84 1/2" SHT. MTL.
4] SCR. MACH. SLOT HD. 8-32 x Ve" BOLT, CARRIAGE 10-24 %114” NUT, HEX B-82
—|—|-|-l-]=|-|=!s[al le] ol ely NUT, WING 10-24
800-0145 ASSY A.C. JUNCTION BOX
WHT SV
600-0130
800-0136
COPPER STRAP 250-0430 BRN/YEL_ OV
BLK 7 WHT l00V WIRING DIAGRAM
BRAIDED
PL MASTER HARN ASSY
800-3104
lo Ed jz
W SYNC} 800-0140 MONITOR ASSY END REVISIONS € Tl DESCRIPTION [pate A [RELEASED 0M] 8-79-80
800-0137 (REF ONLY) 800-0135 COIN BOX ASSY
NC co o 0 COIN MECH
NO NC
COIN MECH
NO
C9 no SLAM SWITCH
COIN ~ COUNTER SERVICE RESET
ey"
B00- 3110 MOONCRESTA BOARD
P5 [6] Pa 800-3105 CONTROL PANEL
GND
2 PLAYER
|_ PLAYER RED
FIRE
RIGHT.
LEFT GRN 800-3107 (REF ONLY) 700-0030] A
PART OR IDENTIFYING NO. NOMENCLATURE OR DESCRIPTION
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES TOLERANCES ARE. FRACTIONS DECIMALS ANGLES PARTS LIST
San Dego, California 92123 XX = ‘APPROVALS ASSEMBLY, TOP GAME, MOONCRESTA UPRIGHT
NEXT ASSY USED ON
‘APPLICATION c ‘CODE IDENT NO. [DRAWING NO.
700-0030 A
SCALE NONE [sHeer 7 oF 7
REVISIONS ZONE | LTR DESCRIPTION DATE | APPROVED RELEASED Ju 7-17-80
s
Ps Z & a a
a
| ° | =| & | Bl v| a] >| x | E] xe] je |
| =z | = | = | |
| i | pal | a} w a) | a a |
| > | a] = | BH] al x] ol B | S| a ja |
M x ol a a| a L
| 9 | ° | ° | Y | ||
| Pane | eo | 3 | So} fs} [Slots | ||
| COIN | COIN | COIN | SLAM | vou | SERVICE | RESET |
COUNTER MECH MECH SW
WIRING DIAGRAM
- 3PL sy 22" i
800-0135 V4" 2PL —— Lae 2PL
LOCATION OF CLIP, WIRE HOLD DOWN TOP VIEW
PART OR IDENTIFYING. NO. NOMENCLATURE OR DESCRIPTION PARTS LIST Gremlin/seca San Oiego, California $2123
[7-11-80
COIN MECHANISM ASSEMBLY, MECHANICAL
NEXT ASSY USED ON APPLICATION SIZE 4¢ ‘CODE TDENT NO DRAWING NO. 800-0135 A
SCALE NONE
REVISIONS Toe DéscmITON Dare] APoROWED ‘A [RELEASED aM [s-.9-80| JF
D
- @) @) c
SECTION G-G (CONTROL PANEL REMOVED)
> INSTALL ITEMS 22,23, AND 24 AS SHOWN ON PRODUCTION MOCK-UP USING STAPLES. B> INSTALL ITEM 43 UNDER ITEM 9.
> XFMR TO BE MOUNTED WITH PRIMARY SIDE TOWARD REAR OF CABINET B B &>INSTALL GROUND STRAP, ITEM 9, AS SHOWN ON PRODUCTION MOCK-UP AND GROUND IT AT THIS LOCATION.
- ROUTE WIRING AND HARNESSES APPROX AS SHOWN < ON PRODUCTION MOCK-UP.
- INSTALL WIRE HOLD-DOWN CLIPS, ITEM 12, APPROX AS fo} SHOWN ON PRODUCTION MOCK - UP. 2 3> THIS CLEAT TO BE CUT FROM EXISTING CLEAT. Ss c=] 2>FASTEN CLEATS WITH GLUE AND ITEM 57, 2PLACES. R
> DRILL PILOT HOLE, 4 PLACES NOTES:
Gl mar | NOMENCATURE u, i Fo | IDENT IDENTIFYING. NO. Of DESCRIPTION PARTS UST
‘ TORE SES ARE: San Bigs, poe A ‘ SECTION A-A ASSY, TOP A
, GAME, MOON CRESTA UPRIGHT
700-0030
| 4 | 3 | 2 | | | 1 |
REVISIONS DESCRIPTION DATE APPROVED RELEASED. JM. |8-19-80. TONE >|8
| = | 4 | | | a - | me |
| j | i | ,@ 8 © 8) | SSS |
yi Poo be 914 2 3PL i
| —— | 182 | a |
DETAIL F DETAIL D INSIDE DOOR) SECTION E-E
| @ | {f | a |
- © 2eL
| (2) | SC) | mi | 1c] |
| (2) | _——— | (14) ep | |
| (+) (45) | rte] 3 | ap |
h ot (6) zr
| |] | (° | OIL | 2 |
——_|| ,
| ©) 1 | " SLOT ON THIS SIDI \ | / | 5/ | ||
| v | / / | 16 | |||
| 534 | ( | a / | [ t | ||
| } 1 | i | | | | | re | |
| 4 | +h | < | |||
| } | n | i | | | ql | i |
| va— | { | im | fo} | ||
| ] | | | i | | | 4 |
se! we bese | 3 te 8
| | et ove | \ el oz ee | S | ||
| -----------------g TP | eee eee 4 | | | LZ | 5 |
| i | 52 X 6h | (20) |
@ ' ® @)
| <a | | | SECTION C-C |
| mantener errr nent Ff | ee nee ---------- | (LOGIC BOARD REMOVED) |
Go| ERE |__roewtF ne no. on Besekienok
| < | PARTS LST | = |
Gremlin Industries,Inc. |
| VIEW B-B | VIEW B-B | ssnonee casera 9 |
| (REAR PANEL AND DOOR REMOVED) | Tacs] «= ASSEMBLY, TOP | iA |
| . | [sd | levee] - GAME, MOON CRESTA |
[spice UPRIGHT
| a | SHE] eRe ERT ERAT Ro | ye | |||||||
| . | —a | D | | 700-0030 | A | ||||||
| APPLICATION | DO NOT SCALE DRAWING | Scar | [erg OF | ||||||
| 8 | 7 | 6 | L | 5 | 7 | 4 | 3 | 2 | 1 |
" wo HALTER oy | cq
aly ww, | ax
5 2\¥| | a Sal i BLK. | i 1
| hy L | _ =
FUSE HOLDER
JUNCTION BOX SCHEMATIC, eno stun SEE DETAIL"AY —
TO TRANSFORMER ‘SMOOTH: wre
(1.00)
(1.00)
BRL
Ko}
| t | 4 | | | 3 | 2 | 1 |
REVISIONS Zone [UR DESCRIPTION ‘Dave | APPROVED
| A] | RELEASED. | Sb [8-3 se] AF |
aa
SOLDER Connection. 2eL D
DETAIL "A" —_
\ us
c
ee Ly] 24.00
| ke) | 4 | 26 {2.0 | [SHRINK TUBING - 1/2 DIA | |||
| U | 25 [2.0/ | SHRINK TUBING = 3/i@ DIA | Z | |||
| Fe, | (1.00) | 24/1 | | 180 - 0008 | CHOKE J - BOX | _| | |
| A | ay Ee | PAL | 23 [6.0 | SHRINK TUBING - 1/4 DIA | I | TF |
- 22/2 [WASHER LOCK # 8 INT. STAR 2/3 NUT HEX. HD. 8- 32 20 | 1 STuD 8-32 X1 _ 19 [2] WASHER , LOCK 4 @ INT. STAR 1a] 2 | NUT HEX. HD. @- 32
| (@) | (20) | Wiz | SCREW @- 32 X5/B |
| zPL | 3PL | ‘al | 1 |
| rer | 15 |2FT, | (@00 = 0079 | CORD_LINE_ZIP |
22 14
| 3 | Bi | G00 - 0001 | ‘CORD_LINE 3 COND. | Toye |
| ral | 514 = 0005 | HOLDER FUSE | | | = |
| uit | 514 = 0001 | FUSE Z AMP 250V SB | din | |
| ot | 510 = 0013, | SWITCH SPDT CHERRY | = |
3 fa)
| 8/3 | 280 - 0010 | NUT WIRE, | } | |
| ‘ | 7/2 | 280 - 0007 | BUSHING S/REL_1/Z | 3 |
| e[t | 270 - 0001 | FILTER EMI | a |
s
| 4[s5 | 2N_~ 0038 | CONN QUICK 3/16 FEM. | a |
| 3 | | | | | |
| z[t | 2 = 0017 | CONN QUICK 1/4 FEM. | | |
| tit | 140 = 0020 | JUNCTION BOX METAL | |
| ITEM] grr | cope | Pan oR | NOMENCLATURE |
TNO. [e200] (ERT | soentARWe no. oe BeScRIETION PARTS LIST Bsus age iw memes” [OTST NG Gremlin Industries, Inc. FRACTIONS DECIMALS ANGLES Sen Soe: <aitorns £2
| = | mets 2 | ARROWS | DATE | A |
harem — RANSON DUONG ASSEMBLY A.C. REERED, = JUNCTION BOX
lilniaid ‘SIZE [CODE IDENT NO.[DRAWING NO. REV
- D 800 - 045 A NOT ASS USE0 OW | ~ |
| "APPLICATION | DO NOT SCALE DRAWING | cae NONE | | seer 1 OF | |
| 3 | 2 | 1 |
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 |
REVISIONS
| Tone] oR | GESCRIFTION | one |
A | RELEASED D__ [7-16-60] f SINC ECN 444 IW 618-8 vo
GNO STRAP 21.00 p ©
| i | BLK 12.00 _AW6 1B | z | ‘ |
| B | BLK 12.00 AWG 18 | 5 | P2 |
| 3k | RED 12.00 AW6 IB | c | ®2O |
RED 12.00 AWG 16 ono) c 4
| 4 —— a | 3 | ©®@ | (s |
| o | i | 1} | CONN VIEWED FROM |
19 = AWG 8, 2.50 WIRING END ED 2PL Pl wRIEN BARS FL ~—_ — RED 27
22 |—
| \ | z | BLU 12.00 | + Zz | ||
| iB | ORN 12.00 | in | |||
| 7 | BRN 20.00 | 7 | 7 | ||
| E | a | 0 | |||
| vhoek | K_ 20.00 | iI | |||
| xsi | vio 20.00 | iz | |||
| 7 | | | GRY 20.00 | lé | ||
| FH | - | BLK 20.00 | 6 | ||
| 4 | BLK 20.00 | S | |||
| K | WHT 20.00 | * | | |||
| R | BLK 20.00 | ; | ba | ||
| Pp | a | : | a | 43 | CONN VIEWED FROM, |
| s | 2 | WIRING END | |||
| 7 | RED 20.00 | 1 |
5 )
| 5 | LL 00 a] | e | wer 2.50 | |||||
| M | TYR | GRN 40.00 | 7 | |||||
| u | _ | ORN 40.00 | 2z | — | ||||
| i | Yet 40.00 | 3) pg | )2® | |||||
| " | LU 40.00 | 14 | ®® | |||||
| 10 | rep_#0.00 | 5 | @@ | |||||
| al | t | _ | BLK 40.00 | } | — | |||
| IS | TYP. P4 & PS | T | — | — | — | — | — | |
| 2 | EL 16.00. | 7 | CONN. VIEWED | — | —_ | |||
| BE | WHT 16.00 | 2| | P5 | FROM WIRING END | _ | _ | _ | Z |
| a | BLK 16.00 | 3 | _ | _ | _ | Z | ||
| u | BLU 16.00 | a | zt | 481 — 0001 | DIODE INA0O2 | |||
| ie | ‘@RN 16.00 | 7 | fu fe | [20 - 0005 | CABLE THE | |||
| 1 | RED _¥o.00 | é | oft | zi ~ 0027 | CONN RING LUG #10 | - | ¢ | |
| 3 [art] | ‘600-0038 | WIRE BRAID FLAT 0654 | i=} | |||||
| 3 [er | 00-0023 | (BLE 2 COND SHIELD | ° | |||||
| 7 [0 | a | 7 | CONN 44 PIN CARD EDGE | 3 | ||||
| eio | [a | OWN FUG AMP Ta FIN | - | 8 | ||||
| sf | aun | NN CAP AMP © PIN | _ | i | ||||
| afz. | ti | PLUG AMP G PIN | a | |||||
| a jr | 2 | PLUG AMP 7Z PIN | ~ | _ | ||||
| zee) | a | SOCKET AMP | — | |||||
| 1 4 | 2 - 004) | PIN: AMP | oO | pO | i | |||
| TEM] gry ] cope | PART Of | NOMENCLATURE |
NDA |G | ERE | went no. Oe BeSeREHON PARTS LIST TORLESS OTHERWTSE SpECTAED — [CONTRACT NO
| A INSTALL CABLE TIES, ITEM I] EVERY @- 6 INCHES AS REQUIRED BETWEEN LOCATIONS SHOWN . | BAIEASGNE ane Is ORES | Gremlin Industries, Inc. |
FRACTIONS DECIMALS ANGLES ‘San Diego, California 92123
| 4. ALL WIRE TO BE AWG 22 UNLESS OTHERWISE SPECIFIED . | ie | wns 2 | TPR | DATE |
| = | ——fPRAWN con DUONG — [715-80 | ASSY HAI | ss | |
| RC | S | ss | ||
| A MARK REF DES. ON SIDE OF CONN. HOUSING USING BLK INK, .I2 HIGH CHARACTERS . | ii | [eres | - | KN |
—— = MASTER M/C AX, COVER ALL EXPOSED WIRE CONNECTIONS WHERE POSSIBLE USING 1/8 SHRINK TUBING . EK = THE [CODE GENT NO [DRAWING WO
| ZA\, USE SOLID BARE COPPER WIRE, AWG 18, TO BUSS CONTACTS TOGETHER . | 030) | D | P00. 3104 | |
| . | NEXT ASSY | USED ON | - | ii |
NOTES. 1
| ‘APPLICATION | D0_NOT SCALE_ORAWING | sexe NORE | | [seer oF | |||||
| 8 | | | 7 | 6 | 5 | 4 | 3 | 2 | 1 |
m w \ / BLK 4.00 / | pf BAe oe 4 Le! i LEFT GHT
APPLY ITEM |, CCNTROL PANEL TO IWWEM 2, SUB-PANEL METAL. ALL WIRE CONNECTION TO BE SOLDERED . ALL WIRE TO BE AWG 22. —] 2 PLAYER a REVISIONS uel DESCRIPTION Dae RELEASED
| 700 = 0030 uso OW APPLICATION
oo N DO NOT SCALE DRAWING, MOON CRESTA T
| SO = 0028 | wSSY SwiTGH Wico | Tha |
| 00 - 3107 | ASS¥_HARN GATROL PANEL MODN CRESTA | P16 |
| 240 - 0009 | BUTTON PLUNGER YELLOW | oa |
| [200 = ‘0007 | BITTON PLUNGER BLACK | 2 |
| — | ks | 8 |
{i _— ~
| T 280 = 0004 | if | ‘CLIP WIRE HOLD DOWN | |
| 253 ~ 0031 | SPACER , WED _SwiTCH | | | |
| 250-- 0366 | ‘SUB - PANEL METAL | i | | |
253 - 0193 CONTROL PANEL GRAPHIC
| CODE | PART OR | NOMENCLATURE | ~] |
BE] ool, Sergesearok PARTS UST mane increas TACT NS Gremlin industries, Inc. eae San Prego, Caufornia 92123 rR - ~~ A [ORR SON DUO ASSEMBLY CONTROL PANEL cocaparest
D | 800 - 3105 sce NONE | 2 |
REVISIONS
| Ton | UR | DESCRIPTION | Bare | APPROVED |
A | RELEASED D
D
fo} °
REMOVE PIN PL (1,2,8-13)
| C | IC GH REF — | 8 |
a ‘ADD JUMPER: — |
FARSIDE =
TN sea PIN TO TC BENEATH ITEM 3
| CUT TRACE FROM K | 3PL (5,7 B14) | | |
TO RMZ_ FAR’
| alia | y | / | SJUMPER TO_R2_(SEE DETAIL B) | Cc |
| Pp | < ADD JUMPER | / |
FROM ITEM 3 PIN 3 TD GH PING / _ JUMPER TO R3_(SEE DETAIL B)
| / | \ | S- CUT TRACE FROM S | / | |
| f | \ | TO GND NEAR SIDE | 2 STRAIGHTEN PIN | |
| a | i | iy | | | QUT TO THE SIDE 3PL (3,4 & 6) |
| 7 | i | DETAIL A | ||
| a | ye | : | = |
ADD JUMPER ON FARSIDE 3PL
| FROM RIZ TO R4 | | | le |
Riz FROM Ril TO R3 ff oe FROM RIO TD R2 \_ ADD JUMPER 3PL REMOVE RZ,R3 & R4 2 U
+ ADD JUMPER TD ITEM 3 PING SEE DETAIL A B REMOVE POT ©) a re ADD JUMPER TO ITEM 3 PIN4 | <x
| | | | | Sj |
DETAIL _B m
| L | — | — | — | =) | 1 |
Ss a
| iz | | | _ | _f | = | —__ | im |
| i3tT | 34-0019 | «| _‘IC 74LS04 | __ | __ | ||
| zi | 834-0026 | ASSY GAME CLEC. M/C. | i | I | ||
| rity | 1470 = 0102 | RESISTOR 1K, V4W, '3 ‘fo | ||||
| TEM] gry | cooe | PART OR | NOMENCLATURE | ~ | ~~ | ||
| Nat |@o0| ent | wenn no. | | | Oe BESET HON |
PARTS LST
| Benin Ate eres | [OONTPATT No. | Gremlin Industries, Inc. |
FRACTIONS DECIMALS ANGLES. San Diege, Canfornte 97x:
| : | ae | TROIS | oATe | ne | ~ | A |
| ag | aa | ASSY GAME ELECTRONICS |
[orecre9, ar
| BAY | 180) | M/C. MODIFIED |
(inl SIZE [CODE IDENT NO. DRAWING NO. T REV.
| 1. ALL JUMPER WIRE TO BE AWG 20 - | 05-0055 | D | $00 ~ 3110 |
NOTES: NOT ASSY U0 OW LA
| : | _| | APPLICATION. | 1DO_NOT SCALE DRAWING | fscate_NONE | sneer | OFF | |||
| 8 | 7 | 6 | 5 | t | 4 | + | 3 | 1 |
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Cut Along This Line
WE WELCOME YOUR COMMENTS!
Your comments and suggestions will assist us in improving the usefulness of our publications. They are an integral part of preparing for revisions of manuals and parts catalogs.
If you have any technical questions about any GREMLIN/SEGA game, are requesting additional publications, or have a suggestion about how we can make our manuals more useful to you, drop us a line or use the handy form below. We value your input.
Fill in if you wish a reply:
Name___SSSSSSSSSSSFirm Distributor Address. Operator City_____—State__Zip. Other.
First Fold Place Stamp Here Gremlin/SEGA 8401 Aero Drive San Diego, CA. 92123 Attn: Customer Service 7 Second Fold o8pq sit ade, eee eee COC CCL
sur] sty Buopy nD,