CATHODE RAY TOMES

Hard Drivin' TM-327 1st Printing

Hard Drivin' (cockpit, rev 7) (Atari Games, 1988) · Technical Manual · 120 pages · 136 sections · original scan

Page 1

TM-327

GAMES

ivi

Operator’s Manual

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

A

ATARI

GAMES

Operator’s Manual

with Illustrated Parts Lists

Patents are pending on several parts of the Hard Drivin’ simulator.

Page 4

Copyright © 1989 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations, Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035

Printed in the U.S.A 1T

Produced by the Atari Games Technical Publications Department. Technical Writing: Rosalind Hutton Editing and Design: Andrea Dencker Illustration: Mary Ohanessian Sumner

Notice Regarding Non-Atari® Parts

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury fo you and your players,

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-Atari parts in the game.
  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:
  • All ground wires in the game are properly connected as shown in the game wiring diagram. ¢ The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMI) ground cage, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

Table of Contents

1 Set Up How to Use This Manual Operating the Simulator. Inspecting the Simulato: Installing the Attraction Sign Assembly .. Adjusting the Glides Control and Switch Locations Setting the Coin and Game Options. Simulator System: Maximizing Earnings Simulator Driving... 2 Self-Test and Diagnostics Automated Self Test... Program ROM and RAM Test... Microprocessor and Board Tests ‘Test Menu Screens . Operator Screens Coin Options Game Options. Custom Game Options . Statistics . Histogram Games Played by Day and Hout Set Controls Screens .... Control Inputs Screen Monitor Test Patterns Set Clock Screen .... Disable Broken Controls Screen ..................... 2-12 Special Functions Screen Main Board GSP Test Main Board MSP Test Main Board Controls... Steering Wheel Submenu Shifter Test Screen .... Main Board ROM Checksums Main Board ZRAM Test ADSP Board Tests Sound Board... LEDs on the Main PCB ............. 3 Maintenance Maintaining and Inspectin; Maintaining Your Simulator...

Removing the Dashboard. Installing the Dashboard. Steering Assembh Greasing the Steering Assembly Replacing the Steering Assembly Potentiometer. Replacing the Steering Wheel Motor Replacing the Steering Wheel Stop Key Switch Assembly ........ Oiling the Key Switch Assembh Replacing the Spring in the Key Switch Assembly... Tightening the Screw in the Key Switch ‘Assembly Actuator... Replacing the Switch on the Key Switch Assembly... 3-13 Clutch Pedal .... Oiling the Brake and Clutch Pedals Replacing the Clutch Potentiometer Replacing the Clutch Springs... Brake Pedal ........ Oiling the Brake Bearing: Maintaining the Brake .. Repairing the Brake... Replacing the Brake Switch Replacing the Brake Strain Gauge and Pedal . Gas Pedal Assembly... Lubricating the Gas Pedal Rewinding the Gas Pedal Pulley Cable. Replacing the Gas Pedal Cable Spring Replacing the Gas Pedal Potentiometer Replacing a Broken Compression or Extension Spring on the Gas Pedal... Shifter Assembly... Installing a New Shifter Boot Replacing a Shifter Potentiometer Replacing the Shifter Magnet or Plate Seat Assembly ... Replacing the Seat ‘Rod End Bearings Replacing Bearings on the Seat Pivot Replacing Main Seat Bearings ... Replacing the Gears on the Seat Assem Replacing the Magnet on the Seat AssembI Replacing the Seat Potentiometer....... Video Display ... Removing the Video Display Replacing the Video Display. Motor Amplifier Assembly .... Removing the Motor Amplifier ‘Assembly. Static-Sensitive Devices .. Replacing Static-Sensitive Devices Speakers .......... Removing a Speaker. Cleaning the Coin Mechanism . Cleaning the Interior Components . 4 Illustrated Parts Lists See the List of Illustrations that follows.

Statistics Sheet

iii

Page 6

Figure 1-1

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-3 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11

Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15 Figure 2-16 Figure 2-17 Figure 2-18 Figure 2-19 Figure 2-20

Figure 2-21 Figure 2-22 Figure 2-23 Figure 2-24 Figure 2-25 Figure 2-26 Figure 2-27

Figure 2-28

Figure 3-1 List of Illustrations

Attraction Sign Installation

Program ROM and RAM Test.... Microprocessor and Board Tests Instructions for Test Menu Test Menu. Coin Options. Game Options. Custom Game Options .. Statistics .

y First Set Controls Screen—Initialize Potentiometers ..... Control Inputs Screen Set Clock Screen... Special Functions Screen. GSP Tests Screen MSP Tests Screen Main Board Controls Screen Pots: 8-Bit Screen...... Pots: 12-Bit Screen.... toe Steering Wheel Submenu Scree:

Send Force Screen. Shifter Screen .. ROM Checksums ADSP Board Tes! ADSP ROM Checksums Tests. Sound Board Tests..... Sound Board Sound Wave ROM Checksums DIP Switch and LED Locations on the Main PCB

Removing and Installing the Dashboard... Figure 3-2

Figure 3-3

Figure 3-4

Figure 3-5 Figure 3-6

Figure 3-7

Figure 3-8

Figure 3-9

Figure 3-10 Figure 3-11

Figure 3-12 Figure 3-13

Figure 3-14

Figure 3-15 Figure 3-16

Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Figure 4-9

Figure 4-10 Figure 4-11 Figure 4-12 Figure 4-13 Figure 4-14 Steering Wheel Has No Feedback and You Have Tried the Set Controls Screens .. w 3-6 Steering Wheel is Turned All the Way to One Side or the Other and You Have Tried the Set Controls Screens... 3-7 Steering Wheel is Very Jerky and You Have Tried the Set Controls Screens... 3-8 Maintaining the Steering Wheel........ 3-10 Maintaining the Key Switch Assembly Clutch, Seat, or Working or Working Erratically and You Have Tried the Set Controls Screens ... Maintaining the Clutch and Brake Assembly ...... Brake is Not Working or Working Erratically and You Have Tried the Set Controls Screens .. Maintaining the Gas Pedal . Shifter is Not Working or Working Enratically and You Have Already Tried the Se¢ Controls Screens... Maintaining the Shifter .... i Seat is Not Locked When it Should be and You Have Already Tried the Set Controls Screens .. Seat is Locked When it Shou Not Be and You Have Already Tried the Set Controls Screens ... Maintaining the Seat Assembly .. Removing the Video Display .

  • 3-12

3-14

3-16

  • 3-18

Cabinet-Mounted Assemblies... Seat Assembly...... Dashboard Assembly Key Switch Assembly Steering Assembly. Shifter Assembly . Clutch and Brake Pedal Assembly Gas Pedal Assembly . Coin Acceptors, Inc, Coin Door Assembly Power Supply Assembly Hard Drivin’ Main PCB Assembly. APU PCB Assembly ... Shifter PCB Assembly Brake PCB Assembly ....

Page 7

Table 1-1

Table 2-1

Table 2-2 Table 2-3 Table 2-4

Table 2-5 Table 2-6

Table 2-7 Table 2-8

Table 3-1 Table 3-2 Table 3-3

Table 3-4

Table 3-5 Table 3-6 Table 3-7 List of Tables

Table 3-8 Troubleshooting the Gas Pedal Simulator Specifications. Assembly .... oi veer 3-21 Using the Self-Test Screens and Table 3-9 Troubleshooting the Shifter Diagnostics. 2 Assembly soe 3-24 Coin Option Settings .. Game Option Settings All Screens Appearing in the Self-Test Custom Game Option Settings. ADSP Scope Loop Diagnostic

Using the DIP Switches.

Maintenance and Inspection Items Troubleshooting All Controls Voltage Inputs and Test Points on the Simulator PCBs . Troubleshooting the Steering Assembly .... Troubleshooting the Key Switch. Troubleshooting the Clutch Pedal ..... 3-13 Troubleshooting the Brake Pedal Table 3-10 Troubleshooting the Seat Assembly... 3-28 Table 3-11 | Troubleshooting the Video Display... 3-35 Table 3-12 Troubleshooting the Speakers............ 3-38

Page 8

Cyberball

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari

vi game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING — Players and/or technicians can be killed or injured if instructions are not followed.
Page 9

Set-Up

How to Use This Manual

This manual is written for operators and service personnel, and provides information for setting up, driving, testing, and maintaining your Hard Drivin™ simulator, The manual is divided into the following chapters:

  • Chapter 1 contains set-up and simulator driving information.
  • Chapter 2 contains self-test procedures and additional diagnostic tests. The self-test is very important in the Hard Drivin’ simulator. You can troubieshoot all the boards, main circuits, and controls using the more than 60 screens. You should regularly check the boards and the controls using the tests in the self-test to keep your simulator in top condition and at top earnings.
  • Chapter 3 contains preventive maintenance, repair procedures, flowcharts, and troubleshooting tables for each control. If you have problems with your simulator, use this chapter to troubleshoot and to repair your simulator. Be sure to peiform the preventive maintenance to keep your simulator in good repair to maximize your earnings,
  • Chapter 4 contains the illustrated parts lists.
Page 10

Set-Up

Operating the Simulator

To maximize your income from the Hard Drivin’ simulator, be sure the drivers know that the simulator is designed to be driven like a real car. To be sure the drivers get the maximum realism from Hard Drivin’ you should regularly do the automated self-test, and check the operation of the controls with the Control Inputs screen in the self-test. By using these two tests, you can keep your game operating in top condition by finding and fixing problems immediately, before earnings drop off. These tests are described in detail in Chapter 2.

NOTE If you are installing a new board set or controls in your simulator, you must go through the Set Controls screen in the self-test. This is explained in Chapter 2. If you turn on your simulator and you see a screen that says Initialize Pot Inputs jnstead of the attraction screens, then you also must reset the controls by doing what the screens Say.

Inspecting the Simulator

WARNING To avoid electrical shock, do not plug in the cabinet until it has been properly inspected and set up for the line voltage in your area.

This cabinet should be connected to a grounded threewire outlet only. If you have only two-wire outlets, we recommend that you hire a licensed electiician to install grounded outlets. Drivers can receive an electrical shock if the cabinet is not properly grounded. Please inspect your Hard Drivin’ simulator carefully to ensure that the simulator is complete and was delivered to you in good condition. Inspect the cabinet and seat as follows: 1, Examine the exterior of the cabinet for dents, chips, or broken parts.

  • Open the lower service door and the small top service panel. (Leave this top panel open:so you can install the attraction sign.) Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Ensure that all plug-in connectors on the cabinet harnesses are firmly plugged in. Do not force connectors together. The connectors are

1-2 Table 1-1 Simulator Specifications

keyed so they fit only in the proper orientation. A reversed connector can damage a printed-circuit board (PCB) and will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in the insulation. d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected. e. Inspect other major sub-assemblies, such as the video display, printed-circuit boards (PCBs), and speaker. Make sure that they are mounted securely and that the ground wires are connected.

Installing the Attraction Sign Assembly

The attraction sign assembly is shipped separately from the simulator. The hardware for assembling the sign and for mounting it on the simulator is shipped in the cash box. This hardware consists of ten 1/4-20 button-head screws 2 inches long with black washers. Mount the sign on the back of the cabinet as shown in Figure 1-1.

  • Lay the attraction sign face down on a clean surface where it won't be scratched.
  • Lay the H-shaped attraction frame on top of the sign. Put the short ends of the H on top of the sign. The harness connection in the leg should be facing the sign. Attach the attraction sign harness to the attraction frame harness. Push the extra wires inside the leg of the attraction frame.
  • Install the six screws and washers through the at-
Page 11

Attraction Sign

Button- Head Screw Washer Attraction Frame Set-Up

Figure 1-1 Attraction Sign Installation traction frame and into the attraction sign. Tighten the screws. Now install the attraction sign assembly on the back of the simulator. You need the other four 1/4-20 two-inch long screws and four flat washers. 4, Open the small top rear panel of the simulator. Push the cabinet harness out through the hole in the upper corner of the back. Make sure it does not catch on the motor amplifier assembly. Connect the simulator harness to the connector in the left leg of the sign. Now push the extra wiring harness back inside the simulator. Be careful that it does not lie on the motor amplifier assembly.

  • Put the attraction sign against the cabinet and line up the four holes in the legs with the four holes in the cabinet. Ww
  • Put the button-head screws and black washers into the legs and screw them into the threaded holes.

Adjust the Glides

When you have located the simulator in the arcade, be sure to screw out the adjustable glides in the base to support it. The Hard Drivin’ simulator is heavy; if you do not lower the glides, the casters may be damaged. Also, when you move the simulator, make sure that you retract the glides,

Control and Switch

Locations

Power On/Off Switch The power on/off switch is located at the bottom rear of the cabinet.

Volume Control The volume control is located behind the upper coin door,

Self-Test Switch The self-test switch located behind the upper coin door, See Chapter 2 for a complete description of the self-test.

Auxiliary Coin Switches An auxiliary coin switch is located on the component bracket behind the upper coin door. Use the auxiliary coin switch to give drivers coin credits.

1-3

Page 12

Set-Up

Coin Counter The coin counter is located behind the upper coin door. The coin counter records the number of coins deposited. (It does not count credits given by the auxiliary coin switch.)

Setting the Coin and Game Options

The Hard Drivin’ coin and game options are set in the Self-Test. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Simulator Systems

The Hard Drivin’ simulator uses seven PCBs to give the realistic look and feel to the driving. These are the main PCB, the ADSP PCB, the motor amplifier PCB (with two motor amplifier driver PCBs), the shifter PCB, the brake PCB, the audio and power PCB (mounted on the power supply assembly), and the sound PCB. These PCBs control simulator software, the video display, and the controls. The main PCB, which is the largest, contains the 68010, the GSP, and the MSP microprocessor systems. The 68010 has program RAM and ROM.. The GSP (Graphic Systems Processor) microprocessor system controls the video RAMs (VRAMs). The MSP (Model Systems Processor) microprocessor system performs all the math functions. The ADSP board and the sound board are mounted with the main PCB. The Motor Amplifier PCB is mounted in a heatsink assembly located on the the driver's left. It controls the steering wheel motor. The Shifter Amplifier PCB is located on the driver's right and controls the gear shifter effects. The Brake PCB is located on the back of the brake and clutch pedal assembly and controls the braking effects.

Maximizing Earnings

For maximum earnings, you should regularly maintain your hard drivin simulator following the instructions in Table 3-1, in Chapter 3. Also, when you set up the simulator and when you collect money you should perform the automated selftest and check the operation of the controls in the Control Inputs screen in the self-test.

: :

Simulator Driving

This section describes the features and driving of the Hard Drivin’ simulator.

1-4 Introduction Slide into the contoured seat and adjust it to fit the length of your arms and legs. Place your feet on pedals of the gas and clutch, try your hand on the stick shift. Select manual or automatic transmission, turn the ignition key and you're off! It’s the ride of your life. You feel the tires grip the road as you take a wide turn at high speed. The feedback steering alerts you of the smallest change in the road. You catch air as you fly the draw bridge and land on the down ramp. You are in control as the car holds the road on the vertical loop.

Driving Mode Hard Drivin’ might look like an arcade game but it drives like a real car. For the best lap times, drive Hard Drivin’ as if it were a real car. The major difference between Hard Drivin’ and a real car is that Hard Drivin’ is much safer to drive. A player can test the limits of our car and his skill with no risk of personal injury, and follow a course that does not exist anywhere in the real world. After inserting the proper number of coins to start the game, the player can select either an automatic or manual transmission. Turning the ignition key starts the game. Drivers can choose between the two different types of tracks—the stunt track or the speed track—by following the posted signs on the road. Each player has a certain (operator-selectable) amount of time to reach a checkpoint or the finish line. Crossing checkpoints and the finish line will reward the player with (operator-selectable) bonus driving time. With Hard Drivin’ a player can test drive a high-powered sports car on a real stunt course. He can jump a draw bridge, negotiate a high-speed banked turn and drive a 360-degree vertical loop, These thrilling stunts, among others, provide the ultimate realistic driving experience. Or maybe high-speed driving is a particular player’s type of excitement. He can “put the pedal to the metal” and try to keep control around the corners, weaving in and out of traffic while avoiding oncoming cars. All this, and more, await the player behind the wheel of Hard Drivin’.

Page 13

All drivers will especially enjoy the unique instant replay feature on Hard Drivin’. Each crash sequence is recorded by the game and replayed. Not only will the driver find this entertaining, but it is also informative. The instant replay shows the driver exactly what he did wrong and why he crashed. (If a driver wants to skip the instant replay, he can press the abort switch or turn the key when the replay starts.) Skilled drivers will find the ultimate competition in the “challenge” lap (or “grudge match” as we at Atari Games like to call it). The game remembers the path of the car driven by the best driver on record. When a Set-Up

driver beats the qualifying lap time, he challenges the car of the past winner in a head-to-head race. Hard Drivin’ is equipped with center-feel steering with continuous force feedback, adjustable swivel seat, gas, brake and clutch pedals, four-speed stick shift, and a medium-resolution monitor. After-market options include a dollar bill acceptor and an overhead display assembly. A limited edition of right-hand-drive Hard Drivin’ games will be available from the factory. Contact your local Atari distributor for further information about after-market accessories.

1-5

Page 14

setup

Page 15

Chapter 2

The Hard Drivin’ simulator is a complex machine. To keep it at peak efficiency and maximum earnings, you should regularly check the functioning of the controls, RAMs, ROMs, PCBs, and microprocessor systems. You can check all of these things when you switch on the self-test. Also in the self-test, you can check the video display, the statistics, and set the internal clock.

abo 2 5 minutes to run. It checks the program

RAMs and ROMs, the video RAMs, color RAMs, the

5 dhputs screen, which you © ‘est Menu scréen. This shows the B main PCB from the steering as pedai, clutch pedal, seat, n makes it easy to check re. fuuncti ning correctly.

If the control inputs,al

earnings may drop sine

by Day pire

«al ormation al out how and when your simulage you hat and fo: ‘differe t problems. ca yet

Page 16

Self-Test

Table 2-1 Using the Self-Test Screens and Diagnostics

Cannot Enter the

Automated Self-T est

When you enter the self-test, the simulator automatically tests the program ROM and RAM, the video RAM, the color RAM, the MSP microprocessor system, the ADSP board, and the sound board. This check takes about five minutes (unless you bypass the test as described in the next paragraph).

NOTE If you do not see anything on the video display screen, you may have a video display problem or a simulator system problem. See DIP Switch at the end of this chapter to diagnose the problem.

2-2 If you do not want to wait for the systems and PCBs to be tested, then skip these tests by turning and holding the key switch on for a few seconds while in the program ROM and RAM screen, Figure 2-1. If you want to go to the attract mode, just turn off the self-test switch.

Program ROM and

RAM Test

When you enter self-test, the simulator tests the program ROM and RAM. The screen in Figure 2-1 shows the results of a program ROM and RAM test. The top of the screen shows the ROM test result. The numbers on the left and the letters on the top of the screen show the locations of the ROMs on the main PCB. If a white box appears, then the ROM at that location was good. If an empty box appears (as shown

Page 17

at 200U and 210U), then the ROM at that location was bad. If nothing appears, then nothing was tested at that location. The RAM is tested after the ROM. If the RAMs have no errors, then you see the message Program RAM OK. If the test finds an ervor, then you see Bad Program RAM At with the bad RAM location listed. This screen disappears after a few seconds and the self-test continues. However, the screen with the results of the complete self-test, shown in Figure 2-2, will show the message Bad Program ROM (or Bad Program RAM) if it found an error in the program ROMs or RAMs.

PROGHA

Figure 2-1 Program ROM and RAM Test

Microprocessor and

Board Tests

After checking the program RAM and ROM, the automated self-test checks the video RAM and color RAM in the GSP system, the MSP DRAM, the ADSP board, and the sound board. (For more information about these systems, see the Simulator Sysiems section in Chapter 1.) You will see Figure 2-2 when the test finishes, which takes four or five minutes. If the system or board is good, you will see OK after the test name. If it is bad, the word Bad precedes the name of the board or system (except for the ADSP board test, which gives more information). If you have a bad system or board, then choose the Special Functions item from the test menu, choose the system or board tests from the submenu, and read the description of the tests in this chapter. A brief description of each microprocessor and board test performed in the self-test is below. PROGRAM ROM: Described above. PROGRAM RAM: Described above. Self-Test

GSP VRAM: Uses the Simple GSP VRAM Test. (Described in the section Main Board GSP Tests.) GSP COLOR RAM: Uses the GSP Color RAM Test. (Described in the section Main Board GSP Tests.) MSP DRAM: Uses the MSP Verify Test. (Described in the section Main Board MSP Tests.) ADSP Board: Tests the ADSP boaid memory and the ADSP-2100. Most of the error messages are self-explanatory. Does Not Respond generally indicates a missing board. Sound Board: Tests ROM and RAM functions on the sound board. If any of them are bad, you will see the message Bad Sound Board on the screen.

BAD PROGRAM ROM PROGRAM RAM OK GSP YRAM OK-—-SIMPLE TEST GSP COLOR RAM OK MSP DRAM OK ADSP BOARD OK SOUND BOARD OK

Figure 2-2 Microprocessor and

Test Menu Screens

After the microprocessor test is completed or you have bypassed it, turn the key to see the test menu screens. Turn the key once to see the screen with the instructions for moving and choosing in the test menu,

USING THE TEST MENU

PRESS LEFT COIN SWITCH : TO MOVE UP OR TO INCREMENT PRESS RIGHT COIN SWITCH TO MOVE DOWN OR TO DECREMENT PRESS ABORT YO CHOOSE ITEM OR TO RETURN TO MENU

TURN KEY FOR ‘MENU

Figure 2-3 Instructions for Test Menu

Page 18

Self-Test

shown in Figure 2-3, Turn the key again to see the test menu, To move down the menu, press the left coin switch. To move up the menu, press the right coin switch. You can choose the test menu item with white letters by pressing the abort button. The test menu, is shown in Figure 2-4, is the primary screen in the self-test. Use this screen to choose screens and tests in the self-test. Choosing any item on this test menu causes a new screen on that subject to appear. This new screen may have additional screens to choose or all the information may appear on that screen. Table 2-4 shows all the screens that appear in the self-test.

: TEST MENU OPERATOR SCREENS SET CONTROLS CONTROL INPUTS: MONITOR TEST PATTERNS SET TIME DISABLE BROKEN CONTROLS. ‘SPECIAL FUNCTIONS :

COPYRIGHT ATARI GAMES ADBB”

S06:24 AM FRIDAY MAY 21, 1989

Figure 2-4 Test Menu

Operator Screens

Choose the Operator Screens in the test menu by turning the key while the words Operator Screens are in white. (For information about moving in and choosing from the menu, see the section above.) Once you choose Operator Screens you must proceed through the next screens. In the last screen you can return to the test menu. To look at any screen again, first go through all the screens, return to the test menu and again select Operator Screens. These are the screens in the operator screens submenu:

¢ Coin Options

  • Game Options
  • Game Statistics
  • Histogram of Game Times
  • Games Played by Day and Hour

Coin Options

The coin options are on the first operator screen (see Figure 2-5). To move and choose in this sereen, do the following:

2-4 Soms to Cont 2 coins - Right Mech Multiplier ‘4-coin counts as.1 coin Lelt Mech Multiplier i.coin counts as 1 coin Bonus Adder No Bonus Adder

Hit LEFT/RIGHT coin switches to move UP/DOWN Hold ABORT and hit coin switches to cycle through choices Hold down abort and turn keyto restore original setting

Figure 2-5 Coin Options To move up or down the list, press the right or left coin switch. To change a setting, press the abort button and a coin switch. To return to the setting that was originally on the screen, press the abort button and turn the key. To exit the screen, turn the key. You can change an option when it is enclosed in the blue box. The default setting of each option is green. The other settings are blue when the option is selected. (The other settings aré white when the option is

Table 2-2 Coin Option Settings

2.coins give 7 extra! 4 coins give Look .

Manufacturer's recommen

Page 19

not selected.) All of the possible settings are shown in. Table 2-2. The coin options are explained below.

  • Coin Mode is the number of coins required for one credit.
  • Coins to Continue is the number of coins required to continue the driving session, © Right Mech Multiplier is the number of coins each coin counts as in the right coin mechanism.
  • Left Mech Multiplier is the number of coins each coin counts as in the left coin mechanism.
  • Bonus Adder lets you choose bonus coins, no bonus, or free play.

Game Options

Use this screen to set the game difficulty and various other operator options explained below. The screen is shown in Figure 2-6, and a table of the options is shown in Table 2-3. To move and choose in this screen, do the following:

  • To move up or down the list, press the right or left coin switch. « To change a setting, press the abort button and a coin switch. ¢ To return to the setting that was originally on the screen, press the abort button and turn the key. © To exit the screen, turn the key. You can change an option when it is inside the blue box. The default setting of each option is green. The other settings are blue when the option is selected. (The other settings are white when the option is not selected.)
  • Game Difficulty sets the game difficulty for the drivers. The setting are shown in Table 2-3, and

Game Difficulty. Medium ‘Steering During Attract Mode in: Steering Wheel Force Stiff High Score Name Censor: Easygoing ‘Cleat High Score Table Clear Every 2 Weeks:

Hit LEFT/RIGHT Coin Switches to move UP/DOWN Hold down abort and turn key fo restore original setting Just turn key to save this setting and exit

Figure 2-6 Game Options Self-Test

give different amounts of time in the easy, medium, hard, and very bard settings. The custom setting lets you choose the actual amount of time the players receive. We suggest you use the preset factory settings,

  • Steering During Attract Mode allows you turn the movement of the steering wheel on or off in the attract mode.
  • Steering Wheel Force is the amount of force exerted by the steering assembly motor on the steering wheel.
  • High Score Name Censor controls a program to censor names entered on the high score table. The program works by deleting letters in possibly objectionable words in the high score table.
  • Clear High Score Table clears the high score table at the time chosen. You can choose not to clear the table, clear it now, clear every week, or clear every two weeks. If you choose clear every week or clear every two weeks it will be cleared the first time the simulator is powered up after midnight on Wednesday if you have your simulator clock set correctly. Otherwise, it will clear whenever the internal clock says it is Wednesday.

Custom Game Options This screen is shown in Figure 2-7. Choose Custom under Game Difficulty to see this screen. You can choose the amount of time each driver is given for each lap instead of using the Game Difficulty options available.

2-5

Page 20

Self-Test Hard Drivin’

Table 2-4 All Screens Appearing in the Self-Test

“Initialize Pot Inputs ” Anitialize Steering Limits itialize Shifter Limits.

Monitor Test Patterns ese Screens to check the perform: Color Bars. ~ “<< Monitor Brightness “Grey Scale. B/W. Grid

Diagonal Lines “

  • Full Scréen Grey Full Screen White” Full Screen Red Full Screen Green ».Full Screen Blue

‘Special Functions Main Board GSP Tests

VRAM Simple Test

“VRAM Verify Test: ‘VRAM Complete Test

  • Test ‘VRAM for Display Errors

2-6

Page 21

Hard Drivin’ Self-Test

Table 2-4 All Screens Appearing in the Self-Test, Continued Screen : S : ee oe Be oom

Main Board MSP Tests

MSP Verify Test. _ MSP Complete Test :

Main Board Controls

Main Board ROM ‘Checksums Main Board: ZRAM Tests

DSP: Board ‘Tests “ADSP RAM. 2100 Test ADSP IRQs

Graphics ROM Checksums

Scope. Loops

Toggle MPAGE. Toggle XPAGE Sound Board Tests - Sound Board Self-Test «° Play. Sounds Pots: 8 Bit Shows the gas pedal, clutch pedal, seat movement, shifter movement, sone avheel | . se movement (not force), line voltage and the shifter ‘force : input tothe main PCB...

Pots: 12 Bit Shows the steering wheel force input- (not move the brake for 7

ee es - the ‘main PCB: Steering Wheel ‘Tests to use if the steering \ wheel oe OE work, ie toasty Chapter 3 for their use. Send-Force Use this test a8 § directed i in ithe flowchart in hoe 3. Sine Wave : : : Square Wave: i . THanglé Wave Use this test 6 directed in the flowchart Cane 3. Closed Loop Test : Line Voltage : Calibrates the line: vole play in ne self test : Calibration: , Opto Test For factory use only. Life Test For factory: use ‘only: Shifter: Use this screen | if the shifter is not fiachoning correctly.

Seq Input Memory Reads.” Ou aihee : : Seq Input Mem ADR Writes. a ee ee Seq Output Writes, Buf 1 coe oe eee a Seq Output ADR Writes, Buf 1 Seq Output Writes, Buf 2 : Seq Output ADR Writes, Buf 2 a.

  • shows much the same information asthe Control Inputs screen, but has additional. ~ tests for the steering wheel and for line voltage calibration,

Use this test if the De ROMs failed (be automated self Ftest. Check the ZRAMs, Use this are not being kept correctly, Use this test if the ADSP board failed the automated self-test. if all the controls are operating erally or the statistics |

Sound Board ROM Checksums Sound Board: Program RAMS Sound Board Program ROMS COMRAM : 320. RAM.

Page 22

Self-Test

NOTE Always use the preset Game Difficulty settings before you use the settings on the Custom game options.

If you choose a preset game difficulty option, the custom time settings will be the same as the preset times. With this screen, you can adjust the time permitted for the first lap and for each additional lap separately. To move and choose in this screen, do the following:

  • To move up or down the list, press the right or left coin switch.
  • To change a setting, press the abort button and a coin switch.
  • To return to the setting that was originally on the screen, press the abort button and turn the key. ¢ To exit the screen, turn the key. You can change an option when it is inside the blue box. The default setting of each option is green. The other settings are blue when the option is selected. (The other settings are white when the option is not selected.) All of the possible settings are shown in Table 2-5. The custom game options are explained below. ¢ Initial Time is the amount of time always given for one driving session. ° First Extended Time is the amount of time given if the driver crosses the finish line before the initial time is up. ° Second Extended Time is the amount of time given if the driver crosses the finish line before the time is up on his second lap.
  • Extended Time After Second is the amount of time given when the driver crosses the finish line before the time is up after the first two laps.

‘Custom Options: initial Fime: ‘90 Median First Extended Time saint Second Extended Time AG Medium Extended Tune Atter Second 45 Medium

Hit LEFTIRICHT Coin Switches to move UP/DOWN ‘Hold down abort ond turn key to restore original setting ‘dust ture key to save this setting and exit

Figure 2-7 Custom Game Options

2-8 Table 2-5 Custom Game Option Settings

Option.

Second Extended ‘Time:

Extended Time _ “After Second: - -

Statistics

The statistics screen is shown in Figure 2-8, The statistics are collected from the last time the statistics screen was cleared. Write this information on the statistics sheet in the back of this manual to assist in maximizing your profit. To move to the next screen, just turn the key. To clear the statistics, press and hold the abort button and turn the key at the same time. The statistics the simulator collects are explained below.

  • Left Coins shows the number of coins counted in the left coin mechanism. ¢ Right Coins shows the number of coins counted in the right coin mechanism.
  • Idle Mins shows the number of minutes the simulator has been idle.
  • Active Mins shows the number of minutes the simulator has been played. *° Xtnded Plays shows the total number of times drivers received at least one additional lap.
  • 1-X Games shows the number of times drivers crossed the finish line one time and did not complete a second lap. ° 2-X Games shows the number of times drivers crossed the finish line two times and did not complete a third lap.
Page 23
  • N-X Games shows the number of times drivers crossed the finish line three times and continued to drive.
  • Auto Games shows the number of times drivers chose to drive the car with an automatic transmission instead of a manual shift. ° £rror Count shows the number of errors counted in the erasable memory. If you have a count of more than 75, you should have your simulator serviced by a qualified service technician.
  • Total Games shows the number of unique games played, regardless of how additional laps a driver received.
  • Laps by Track is numbers of laps, completed or not, on each track. The first number is the common track at the beginning, before the driver chooses the stunt track or the speed track. The second number is the speed track and the third number is the stunt track. See the example after No X Games by Track.
  • Xinded Plays by Track is the number of additional laps given to drivers if they complete the track before the time allotted. (These laps, when added together, are the same as the number of laps in Xinded Plays.) These additional laps does not need to be completed to be counted. The first number is the common track at the beginning, before the driver chooses the stunt track or the speed track. The second number is the speed track and the third number is the stunt track. This is statistic is useful to see which track drivers are choosing and driving weil on. See the example after No X Games by Track.
  • No X Games by Track is the number of times the drivers did not get extended games on either track. If the numbers here are very high (in proportion to the Laps by Track statistic), then the Game Difficulty setting may be too hard. The first number is the common track at the beginning, before the driver chooses the stunt track or the speed track. The second number is the speed track and the third number is the stunt track. The following examples show how these three statistics are counted. If a driver chooses the speed track and completed it before the time allotted, started driving the second lap on the speed track, but ran out of time, and did not put in any more coins, you would see the following Statistics:
Laps By Track020
Xtnded Plays by Track0a0
No X Games by Track000

If a second driver chooses the stunt track and does not Self-Test

Statistics Left Coins = 5 Right Coins: Idle Mins: Aetive Xtnded Plays:

Total Games:

Laps by Track:6ot
Xtended Plays by Track: 0a342
No X Games by Track:046.(47

‘Champ Laps: 56. Wins 42 inst Rpls | 94 Rpl Aborts 49: ipl Secs. ‘total Credits: 123 ‘Avg Time/Gredit: 127 secs

Hold down ABORT and turn Key to clear statistics. dist furn key for histograms

Figure 2-8 Statistics

complete the track before time is up, his statistics will be added to the first driver's as follows:

Laps By Track021
Xtnded Plays by Track010
No X Games by Track001
  • Champ Laps is the number of times drivers qualify to race a championship lap. « Wins is the number of times drivers win championship laps.
  • Inst Rpls is the total number of instant replays. If this number is very high, the drivers should probably be reminded they will be most successful if they drive the Hard Drivin’ simulator like a real car.
  • Rpl Abort is the number of times the drivers pressed the abort button to cut the instant replay short, ¢ Rpl Secs is the total number of seconds the simulator is in the replay mode.
  • Total Credits is calculated by multiplying the coins by the credit setting you chose in Coin Mode. © Avg Time Per Credit is the average amount of time in seconds that each credit gave.

Histogram

The histogram screen shows the length of driving time in seconds and the how many times the simulator was driven . The screen is shown in Figure 2-9. Write these numbers on the statistics sheet in the back of this manual to assist in maximizing your profit. To move to the next screen, just turn the key, To clear the histograms, press and hold the abort button and turn the key at the same time.

Page 24

Self-Test

Figure 2-9 Histogram

Games Played By Day and

Hour This screen, iltustrated in Figure 2-10, shows the number of games played in every hour in each day. The information on this screen relies on the clock being set correctly. You can easily check the accuracy of the clock setting by looking at the time, day, and date shown on the bottom of the test menu screen. If the time is incorrect, follow the instructions in the Set Clock section to set the clock. Write the simulator driving information on the statistics sheet in the back of this manual to assist you in maximizing your profit. To clear the screen, press and hold the abort button and turn the key at the same time. To return to the self-test menu, turn the key. If you want to see any screens again, select Operator Screens on the test menu.

Set Controls Screens

If you are having problems with any control in the simulator, use these screens first before doing any other troubleshooting or repairs, These screens allow you to set the beginning and ending points of the conirol input to the main PCB. Often, resetting these points will solve the control problem you have. If it does not, then you should check the Control Inputs screen, described below. If you do repair a control, when you put the control back in the simulator, go through the Set Contro! screens. If you install a new board or a new control, you must go through the Set Control screens too.

2-10

Man Sar

Games Hayed by Day and Hour Tus Wed Thu Ew

Hold ABORT and tum key to clear table Just lun Key tor self test mend:

Figure 2-10 Games Played by Day and Hour

NOTE If you take a control out of the simulator for repair or maintenance, you must go through all the Set Controls screens after you replace it. If you do not, the simulator will not operate correctly. If you have never used the self-test, then read pages 2-2 to 2-5 to find out how to see these screens.

After you choose Set Controls, simply do what the screens say. You must reset all the controls after you Start the screens. The first screen initializes all potentiometers in the simulator. (The steering wheel, shifter, seat, gas, and brake have potentiometers.) The next screens initialize the limits for the steering wheel,

INITIALIZE POT INPUTS: JAKE VOUH HANDS AND FEET OFF ALL CONTROLS THEN TURN KEV

Figure 2-11 First Set Controls Screen—Initialize Potentiometers

Page 25

shifter, seat, and brake. The numbers on each screen are for factory use.

NOTE When you initialize the brake, the instru ctions say to “step firmly” on the brake. Do not stomp on the brake or gently press it. Either one will cause the brake to have incorrect limits, and the players will be fru strated when they use the brake.

The first screen of the Set Controls screens is shown in Figure 2-11.

Control Inputs Screen

Check this screen as part of your regular maintenance to be sure your controls are operating correcily. This screen shows the voltage inputs from the control potentiometers to the A/D converter circuit on the main PCB. As you use a control, the line length on the screen changes, showing the change in the voltage input from the potentiometer. If the line length does not change, you have a problem with that control, the connections, the harness, or the A/D converter circuit. If you have a problem, do the Set Controls screen first to see if that solves the problem. If this does not solve the problem, check the Maintenance chapter for troubleshooting and repair information before you take the control out of the simulator for repair. The Control Inputs screen is shown in Figure 2-12. The first two controls on the screen are the Steering Wheel force and Brake Force. These lines measure the force with which the steering wheel is turned and the brake is pushed. As you turn the steering wheel counterclockwise, the line disappears. As you push harder and harder on the brake, its line disappears. In both these controls, 0 Volts from the control is a very short line on the screen (or no line) and 5 Volts is almost eight full lines drawn across the screen. Below these two lines are inputs from the gas pedal, clutch pedal, seat movement, shifter (front to back), shifter (left to right), steering wheel position, line voltage, and shifter force. The line voltage varies at 60 Hz. ‘You cannot test the line voltage. As you use the controls, the lines should become longer and shorter. If the line does not move, then see Chapter 3 for more information. In these controls, which all feed into the 8-Bit A/D circuit on the main PCB, 0 Volts appears as a very short line (or no line) Self-Test

Figure 2-12 Control Inputs Screen and 5 Volts appears as a line halfway across the screen. At the bottom of the screen, you can check the left and right coin mechanism, the auxiliary coin switch behind the coin door, and the seat magnet. The seat magnet locks the seat while driving and unlocks in the attract mode, or when the seat adjust button is pressed, With the seat magnet test you can determine whether the seat is locking and the magnet is good. If the seat locks in this test, but has not been functioning correctly then you probably have a problem with the switch, not the magnet. If the seat does not lock, then you probably have a problem with the harness or the magnet.

Monitor Test Patterns

Use this item to see thirteen screens for checking the video display, the color RAMs and the GSP, which controls the video RAMs (VRAMs) and the video output. Some screen can be used to adjust the video display. To move through the screens, press the coin switches.

  • Color Bars screen shows from left to right, the colors white, yellow, light blue, green, purple, red, blue, and grey. If the colors are incorrect, see your video display manual included with the simulator for adjustment procedures.
  • Monitor Brightness checks the adjustment of the video display brightness.
  • Grey Scale screen shows a white line on the left, then black shading to white across the screen.
  • B/W Dots screen can be used to check convergence and focus.
Page 26

Self-Test

  • B/W Grid screen, shows a black background and a white grid pattern to check convergence. The grid lines should be straight within 3.0 mm. If you need to adjust the convergence, see the video display manual included with the simulator.
  • Diagonal Lines screen can be used to check video display linearity.
  • Full Screen Color Screens test the color purity in the color RAMs and the display. The test displays a grey, white, red, green, and then blue screen. Each screen should be a rectangle of color, with no curving at the corners and no lines in the raster. If it does not, see your video display manual included with the simulator for adjustment procedures.
  • Monitor High Voltage Test screens switch between a white screen and a grey screen. If the high voltage to the display is regulated properly, the sides of the screen will fluctuate about 3/4-inch between the white and grey screens.
  • Scrolling Test screen checks the scrolling mechanism in the GSP.

Set Clock Screen

Choose this item if you want to set the clock, turn the clock on, or turn it off. The clock should be set correctly so statistics on the operator screen Games Played by Day and Time will give the proper information and the high score table will be cleared on Wednesday. You may need to turn on the clock if the simulator has a program crash. Turn off the clock only if you plan to store the simulator more than six months. The clock has a lithium battery that should last more than five years if the simulator is in normal use. To turn off the clock, choose Clock Off from the clock submenu, shown in Figure 2-13. To turn on the clock, choose Start Clock from the menu. In about two seconds, the clock will start. If the clock is losing or gaining time, then use Clock Faster or Clock Slower to adjust the calibration of the clock. Choose the item you need from the menu by using the right and left coin switches. Change the item setting by turning the key until you see the correct time. The items on the clock menu are explained below. ° Exit returns you to the test menu. ¢ Inc Hours changes the hour setting ahead.

  • Inc Minutes changes the minute setting ahead. « Inc Seconds changes the second setting ahead.

2-12 EXIT. INC HOURS ING MINDTES INC SECONDS. ING DAY: INC MONTH INC DATE: INC YEAR FASTER CLOCK CLOCK OFF DEC HOURS DEC MINUTES DEC SECONDS DEC DAY DEG MONTH DEC DATE DEC YEAR: SLOWER CLOCK START CLOCK

CALIBRATION: +000 SECS/MONTH 11:22:21 AM NOVEMBER 22, 1988. FRIDAY.

Figure 2-13 Set Clock Screen

  • Inc Day changes the day of the week (for example, Monday or Tuesday) setting ahead.
  • Inc Month changes the month setting ahead.
  • Inc Date changes the date setting ahead.
  • Inc Year changes the year setting ahead.
  • Faster Clock changes the calibration setting ahead. Each increase in the calibration setting makes the clock run about 5 seconds faster per month.
  • Clock Offturns the clock off. ¢ Dec Hours changes the hour setting back.
  • Dec Minutes changes the minute setting back.
  • Dec Seconds changes the second setting back.
  • Dec Day changes the day of the week (for example, Monday or Tuesday) setting back.
  • Dec Month changes the month setting back.
  • Dec Date changes the date setting back.
  • Dec Year changes the year setting back.
  • Slower Clock changes the calibration setting back. Each decrease in the calibration setting makes the clock run about 5 seconds slower per month.
  • Start Clock starts the clock.

Disable Broken Controls Screen

Use this screen if you have a broken shifter, brake pedal, clutch pedal, or seat potentiometer and cannot fix it immediately. Before you use this screen try the Set Controls screens to see if that will solve the problem. Disable these controls only as a temporary measure so you can continue to operate the simulator while wait-

Page 27

ing for parts. If you disable a control, the realistic driving feel of the simulator is lost for that control. Earnings could potentially drop. When you disable a control, the control circuit is overridden, and the simulator compensates for the loss of the control so that you can continue to operate the simulator.

Special Functions

Screens

The items on this screen menu, shown in Figure 2-14, should be used if you need more information about systems or boards that failed the Program RAM and ROM Test or the Board and Microprocessor Test at the beginning of the self-test. You can also test the steering wheel, the shifter, and the non-volatile RAM that holds the clock settings and the statistics. The Special Functions screen is explained below. ° Exit returns you to the test menu. Main Board GSP Tests should be used if you get the message Bad GSP VRAM or Bad GSP Color RAM at the beginning of the self-test. Main Board MSP Tests should be used if you get the message Bad MSP DRAM at the beginning of the self-test. Main Board Controls gives you most of the same information as provided in the Control Inputs screen. However, some steering wheel tests and a line voltage calibration screen have been added. Main Board ROM Checksums should be used if you get the message Bad Program ROM at the beginning of the self-test. Main Board ZRAM Tests should be used if your controls settings are changing or erratic after you used

SPECIAL FUNCTIONS MENU

EXIT ‘ MAIN BOARD GsP TESTS MAIN BOARD MSP-TESTS MAIN BOARD CONTROLS MAIN BOARD ROM CHECKSUMS MAIN BOARD ZRAM TESTS | ADSP BOARD TESTS SOUND BOARD TESTS

Figure 2-14 Special Functions Screen Self-Test

the Set Controls screen or if you suspect the simulator is not keeping the statistics correctly. ° ADSP Board Tests should be used if you get any message other than ADSP Board OK for the ADSP board test at the beginning of the self-test.

  • Sound Board Tests should be used if you get the message Bad Sound Board at the beginning of the self-test. However, many of the sound board tests require schematics and an oscilloscope.

Main Board GSP Tests

If the automated self-test reports bad VRAMs, choose Main Board GSP Tests and you will see the screen in Figure 2-15. First run the VRAM Simple Test. It will give you the location of the bad VRAMs. If the VRAMs pass this test, but you think the simulator has a bad VRAM, run the VRAM verify test. ° VRAM Simple Test is the same test that is run at the beginning of the self-test. It is run by the 68010 through the GSP interface and detects open or shorted address or data lines or missing parts. The results are displayed on-screen with a picture showing the VRAM section of the main board. The good parts are shown in green and the bad parts are shown in red. If an entire section is shown as bad, the problem may be with a buffer associated with that section. The test takes about 30 seconds. ° VRAM Verify Test is a complete memory test run by the GSP. The results are reported on the screen like in the simple test. The test takes about three minutes to run,

Since the GSP program resides in the VRAM and runs the test, a single bad VRAM will probably cause the GSP program to crash. If the program does not run, the 68010 will time out and report that all the VRAMs are bad. Actually, probably only

EXIT VRAM SIMPLE TEST: 35 SECONDS VRAM VERIFY TEST: 3 MINUTES VRAM COMPLETE TEST: 22 MINUTES TEST VRAM FOR DISPLAY ERRORS COLOR RAM VBAM SHIFT REGISTER TEST

Figure 2-15 GSP Tests Screen

Page 28

Self-Test

one VRAM is bad and you should run the VRAM complete test to find out which one is bad. If the test does run and report that the VRAMs are good, then the VRAMs should be good. If the VRAM verify test fails, but the VRAM simple test shows the all the VRAMs are good, you should also run the VRAM complete test. *¢ VRAM Complete Test is a complete memory test but the 68010 runs it through the GSP interface. Because the 68010 runs the test, a bad VRAM will not cause the test to crash. The test reports any VRAMs that are bad on the screen at the end of the test. This test takes at least 22 minutes to run.

  • Test VRAM for Display Errors checks to see if there are any video display problems.
  • Color RAM is the same test that is performed at the beginning of the self-test. It tests the color RAM and reports the results.
  • VRAM Shift Register Test test the shift register section of the the video RAMs.

Main Board MSP Tests

Use this item if the MSP microprocessor fails the Microprocessor and Board Tests performed when you enter the self-test. Choose Main Board MSP Tests and you will see the screen shown in Figure 2-16. Run the MSP Verify Test, and if necessary, the MSP Complete Test. The items in the MSP Test screen are explained below. ¢ Exit returns to the test menu. ¢ MSP Verify Test tests the MSP DRAMSs. This is the first test you should run if the MSP microprocessor failed Microprocessor and Board tests. The test is run by the MSP out of the DRAM; almost any DRAM problem will cause an error message to appear on the screen. In twenty seconds, the test displays the results as a picture of the main board with the good parts shown in green, the bad parts shown in red, and the integrated circuits that are not DRAMs and not tested shown in blue. If two DRAMs are colored red, then the problem could be the buffer associated with the pair. If this test does not isolate the MSP problem, then try the MSP Complete Test. MSP Complete Test is ran by the 68010 through the MSP interface. It thoroughly tests the DRAMs and can detect nearly any problem that could develop. The test takes 2 minutes or longer if it finds errors, The test displays the results as a picture of the main board with the good parts shown in green, the bad

2-14 EXIT MSP VERIFY TEST: 20 SECONDS MSP COMPLETE TEST: 2 MINUTES

Figure 2-16 MSP Tests Screen parts shown in red, and the integrated circuits that are not DRAMs and not tested shown in blue. If two VRAMs are colored red, then the problem could be the buffer associated with the pair.

Main Board Controls

This screen provides more information about the controls than shown in the Control Inputs screen. The items on the screen are described below and shown in Figure 2-17. After you choose any item on this screen and go to that item, you can return to this screen by turning the key. The first two items on the screen are the same as are shown the Control Inputs screen. These are the voltage inputs from the potentiometers on the controls to the A/D Converter. As you use a control, you can see the voltage input from the potentiometer to the A/D converter change. If the voltage does not change, you should check that control according to the procedures in Chapter 3, Maintenance and Troubleshooting. + The controls under the heading Pots: 8-Bit feed

MAIN BOARD CONTROLS

Exit. POTS: 8 BIT POTS: 12 BIE STEERING WHEEL SHIFTER DUART

Figure 2-17 Main Board Controls Screen

Page 29

GAS CLUTCH SHIFTER F/B SHIFTER UR WHEEL LINE VOLTS SHIFT FORCE

Figure 2-18 Pots: 8-Bit Screen

into the 8-Bit A/D converter circuit on the main PCB. (See Figure 2-18.) These are the gas pedal, clutch pedal, seat movement, shifter (front to back), shifter (left to right), steering wheel position, and shifter force. As you use the controls, the lines should become longer and shorter. If the line does not move, then you have a problem with the control, the connection or the A/D Converter circuit on the main PCB. In these controls, 0 Volts appears as a very short line (or no line) and 5 Volts appears as a line halfway across the screen.

  • The Steering Wheel force and Brake Force under the heading Pots: 12-Bit feed into the 12 Bit A/D converter circuit on the main PCB. (See Figure 2- 19.) These lines measure the force with which the steering wheel is turned and the brake is pushed. As you turn the steering wheel counterclockwise, the line disappears. As you push harder and harder on the brake, its line disappears too. If the line does not move, then you have a problem with the

Figure 2-19 Pots: 12-Bit Screen Self-Test

control, the connection, or the A/D Converter circuit on the main PCB. In both these controls, 0 Volts from the control is a very short line on the screen (or no line) and 5 Volts is almost eight full lines drawn across the screen. The two lines on the bottom of this screen are not used, Steering Wheel has a submenu explained below and shown in Figure 2-21.

  • Shifter screen is described below and shown in Figure 2-22. To enter the shifter screen, you must quickly turn the key. If you turn it slowly, you may not be able to enter the test. ¢ Duart does not apply to this simulator.

Steering Wheel Submenu

Use these item if you believe you have a problem with the steering assembly or the steering motor amplifier PCB The screen is shown in Figure 2-21.

CAUTION Do not attempt to service the motor amplifier assembly, which drives the steering assembly and is mounted on the left side of the cabinet. The assembly contains high voltage. If you think the problem is with the motor amplifier assembly return the assembly to Atari Games for servicing.

To move through the menu and the screens, use the coin switches. To exit the screens, push both coin switches down.

STEERING WHEEL

EXIT SEND FORCE SINE WAVE SQUARE WAVE TRIANGLE WAVE CLOSED LOOP TEST LINE VOLTAGE CALIBRATION OPTO TEST LIFE TEST

Figure 2-20 Steering Wheel Submenu Screen

2-15

Page 30

Self-Test

¢ Exit returns to Main Board Controls. ¢ Send Force sends a steady force to the Motor Amplifier PCB. See Figure 2-21.

  • Sine Wave sends a sine wave force to the Motor Amplifier PCB. This screen is similar to Figure 2-21.
  • Square Wave sends a square wave force to the Motor Amplifier PCB. This screen is similar to Figure 2-21.
  • Triangle Wave sends a triangle wave force to the Motor Amplifier PCB. This screen is similar to Figure 2-21.
  • Closed Loop Test reads the steering wheel position and sends a force to the steering wheel motor amplifier PCB to simulate a simple spring.
  • Line Voltage Calibration can be used to calibrate the simulator voltage reading to the line voltage teading. Put a voltmeter on the line, then set the voltage on this screen to match.
  • Opto Test is a test used by manufacturing.
  • Life Test is a test used by manufacturing quality assurance.
CAUTION Do not use the Life Tesi. /t is used only for factory testing of potentiometers. If you leave the simulator in this test for a long period of time, you can destroy your steering assembly potentiometer.

SEND FORCE PRESS INC TO INCREASE POSITIVE FORCE

PRESS DEC TO DECREASE

POSITIVE FORCE

HOLD KEY FO EXECUTE +0000

10 EXIT PRESS INC AND DEC AT THE SAME TIME

8B POT: OOAE LINE VOLTAGE: 6112 126 POT: OABT THe

Figure 2-21 Send Force Screen

Shifter Test Screen

Use this screen if you think you have a problem with the shifter However, first see the shifter flowchart in Chapter 3, so you can use this screen effectively. If

2-16 SHIETER TEST

SHIFTER OUTPUTS XPOT 179 STRAIN GAGE 90 YPOT 75

SHIFTER INPUTS EXET SG BIAS — 128 DEC BRAKE FORCE = 0

Figure 2-22 Shifter Screen

you need to repair the shifter or the shifter PCB, see the shifter section in Chapter 3 for further information.The shifter screen is shown in Figure 2-22. You may have some difficulty entering this screen when you turn the key. If you quickly turn the key, you will see the shifter screen in Figure 2-22. If you hold the key too long, you will see Shifter Test Quit. Just try again if this happens if you see this screen. Under shifter outputs, you can see the voltage outputs change as you push the shifter from left to right and. front to back. These numbers show the change in the voltage input from the the potentiometers to the 8-bit A/D converter circuit on the main PCB The X pot number should change as you move the handle from left to right. The Y pot number should change as you move the shifter front to back. The strain gage should be 90, and when you push the shifter forward into first or third gear, the number should go higher. It changes very quickly so watch carefully for it. Under Shifter Inputs, you can exit the screen by turning the key, or you can press the coin switches to increment and decrement the SG Bias (strain gauge bias) and shifter Brake Force. (This brake is the internal shifter brake, not the simulator brake.) Change the inputs to the strain gauge and the brake force as directed in the shifter flowchart in Chapter 3.

Main Board ROM Checksums

This item checks the main board program ROMs for errors, Use this test if you have a Bad Program ROM message on the self-test screen or you suspect program ROM failure. To exit this screen, turn the key. When the checksum test is complete you will see a

Page 31

hexadecimal number following each ROM as shown on the screen in Figure 2-23. The first two digits in each hexadecimal number can be any number, but the last two digits must be the ones shown in Figure 2-23. If they are not, then the ROM is bad or it is not on the board.

PROGRAM ROM CHECKSUMS. ROMOH = xx02 ROM OL ROMITH = xxd4 ROMiL

ROM 2Hx06ROM 2
ROM 3H*x08ROM OL
ROM 4HxXIO.ROM AL

ROM 5 H ROM 5t ROM 6H ROM EL ROM 7H ROM 7L xx12 x14 exci:

Figure 2-23 ROM Checksums

Main Board ZRAM Test

This test checks the non-volatile RAM where the simulator statistics and control set-up values are kept. Use this to check the ZRAMs if you think the statistics are incorrect or the control settings have the wrong values or do not keep the correct settings after being set with the Set Controls screens. If the simulator loses power or is reset while it is in this test, then both the statistics and the control setting will be lost. If this happens, use the Set Controls item Self-Test

EXIT ADSP RAM S100 TEST IRQ TEST ROM CHECKSUMS SCOPE LOOPS

Figure 2-24 ADSP Board Tests from the main menu to reset the controls. The statistics cannot be restored.

ADSP Board Tests

Use this item if the ADSP board fails the Microprocessor and Board Tests performed when you enter the self-test. Select ADSP Board Tests from the test menu and you will see the screen in Figure 2-24. The items on the screen are explained below. ¢ Exit returns to the test menu.

  • ADSP RAM tests the memory on the ADSP board. The test takes a few minutes to run and then displays a picture of the main board with the good parts shown in green, the bad parts shown in red, and the integrated circuits that are not RAMs and not tested shown in blue. If two RAMs are colored

Table 2-6 ADSP Scope Loop Diagnostic Tests

Test

Seq Input Memory Reads

Seq Input Mem ADR Writes

Seq Output Writes, Buf 1

~ Seq Output ADR Writes, Buf 1.

Seq Output Writes, Buf yr

: BSA12. Seq Output ADR Writes, Buf 2

i “ASAT. Toggle MPAGE Toggle XPAGE Reads the sequential input | memory. The: counters 9L, 9K, 9J, and ” are: nce: mented in a binary sequence from SRAQ to SRAIS. : “Writes to the sequential input memory. The data written. to he counters, oL OK, pee OJ, aind 9H is incremented in a binary. sequence from SRAO to SRALS. e Writes ‘to the “Sequential Output ‘Memory 1. The | outputs: ‘of the ‘counters 4D; 4c, Bee

4B, and 4A are incremented in a binary sequence from ASAO to ASA12. : ters 4D,4C; 4B, and-4A is ‘incremented i in a bin

Writes the address to the Sequential Output Memory 1: Data written 1 to he coun :

Writes the address to the Sequential Output Me: ory 2. ters 46, 4, 44, and 4) ‘ ‘Writes the address to the sequential Output Memory 1, Data written to the counters 4D, 4C, 4B, and 4A is incremented in a binary quence from. ASAO to The MPAGE at TL, Pin 5; allcaes between 0 and 1. The XPAGE at 6K, Pin 5, alternates between Q/and 1.) Function

incremented a bin sequ ce from, BSA0 to

2-17

Page 32

Self-Test

red, then the problem could be the buffer associated with the pair.

  • 2100 Test checks the response of the 2100 integrated circuit on the ADSP board by copying data from one location to another using a 2100 program. © IRQ Test checks if the ADSP can generate interrupts for the 68010.
  • ROM Checksums tests the graphic ROMs on the ADSP board. When the checksum test is complete you will have a hexadecimal number following each ROM shown on the screen in Figure 2-25. The first two digits in each hexadecimal number can be anything, but the last two digits must be the ones shown in Figure 2-25. If they are not, then the ROM is bad or it is not on the board.
  • Scope Loops shows a menu with hardware diagnostic tests to be used with an oscilloscope. The tests are shown in Table 2-6.

Figure 2-25 ADSP ROM Checksums Tests

Sound Board

Use these tests if the sound board failed the Microprocessor and Board Tests performed when you entered the selftest. If the Sound Board failed the test, select this item from the test menu. You will see the screen shown in Figure 2-26. Many of the tests require an oscilloscope and schematics, These are indicated on the list below. All the items are explained below.

  • Exit returns to the test menu. ¢ Play Sounds takes you to the Requesting Sound Screen. Follow the instructions on the screen to hear the sounds,
  • Self-Test performs the same test that was used in the Microprocessor and Board tests. These are the sound program ROM, sound program RAM, COMRAM, and 320 RAM tests. Figure 2-26 Sound Board Tests ¢ SD ROM Checksums displays the location of the ROM, a hexadecimal number, and then the results of the check. See Figure 2-27. The results can be the following: Ni—Nothing is loaded in that socket. BAD—The ROM is bad.

OK—The ROM is OK. PROG DEV—The ROM is a program development ROM. You do not need to do anything about this message. 320 Sweep—Runs a program in the sound board 32010 to generate a sine wave sweep from 20 Hz to 9 KHz (requires oscilloscope). 320 Tune—Runs a program in the sound board 32010 to play a tune. Program ROM—Tests the sound board program ROMs with the sound board 32010 and reports the results on the screen. Program RAM—Tests the sound board program RAMs

SOUND BOARD TESTS SOUND WAVE ROM CHECKSUMS FREE NL TEC? OK £B00 4313 5190 TESS £R29 DECG 3138 GA3S FREE q6cs AL PROG DEV

Figure 2-27 Sound Board Sound Wave ROM Checksums

Page 33

with the sound board 32010 and reports the results on the screen. COMRAM—Tests the sound board communications RAM with the sound board 68000 and reports the results on the screen. 320 RAM—Tests the sound board 32010 Program RAM with the sound board 68000 and reports the results on the screen. LED Test—Flashes the Test LED with the sound board 68000. DAC Ramp—Mtites to every DAC value with the sound board 68000. The sawtooth frequency is about 60 Hz (requires oscilloscope). DAC 250 Hz—Writes to every fourth DAC value with the sound board 68000. The sawtooth frequency is about 250 Hz (requires oscilloscope). SA Counter—Creates an oscilloscope loop for the sound address counter (requires oscilloscope). SB Latch—Creates an oscilloscope loop for the sound block latch (requires oscilloscope). 320 Tone—Plays a sine wave tone created by the 32010 (requires oscilloscope). 320 IRQ—Generates interrupts with the 32010 which are recognized by the 68000 (requires oscilloscope). 320 DAC Ramp—The sound board 32010 ramps the DAC (requires oscilloscope). 320 DAC Ones—The sound board 32010 writes walking ones through the DAC latch (requires oscilloscope). 320 SBLOCK—The sound board 32010 writes increasing addresses to the Sound Block Latch (requires oscilloscope). Self-Test

LEDs on the Main

PCB

The LEDs (light emitting diodes) on the main PCB show you the status of various signals on the main PCB. Using the LEDs, you check signals from various circuits going to the 68010 processor. The state of the signals is indicated by the LEDs on the main simulator board which flash or stay lighted. Figure 2-28 shows the location of the LEDs on the main PCB. Table 2-7 shows the the possible status of the LEDs, with an explanation of what they indicate.

DIP Switches

If you try to enter the self-test, but nothing appears on the screen, use the DIP switch tests. The information from these diagnostic tests will help you find the problem so you get your simulator working again. Before you begin with these following tests, be sure that the problem is in the simulator hardware, not in the video display. If you have a completely dark screen, check the following:

  • Do you have power to the video display?
  • Are the video display’s filaments lit?
  • Do you have high voltage to the video display? If the answer to any of these is no, then you have a problem in the video display. Check the video display service manual inciuded with your simulator for the suggested procedure.

Table 2-7 LED Status

LED Run LED Indicates Staté of 68010 HALT signal.

DTACK LED State of 68010 DTACK (data acknowledge) signal.

Clock LED State of thie’ 68010 processor clock signal.

IRQS LED ©. State of all 68010 interrupts. Status On when 68010 is running, Off when.68010 processor is ‘not running. Flashing at 2:Hz if the 68010 cannot run, (The watch-dog arid clock must be'running.) ‘(The Run LED is on in-game mode.)

On when the-68010 processor is Tung and thé: timing Cit

cuit is ‘probably operating:

Flashes at 2 Hz when the 68010 processor cannot run. (The (The DTACK LED is on in game mode.)

watchdog and processor clock must be ruinning.).

‘On when the game board is on. Offif the processor clock signal & stuck high or eon On in the game mode.

Offin hardware diagnostic mode and the oy part of self

test. Offif no interrupts are ccuring or any ‘interrupt signal is. stuck low.

2-19

Page 34

Self-Test Hard Drivin’

DTACK LED Clock LED

Run LED IRQs LED

ca |___ Reset a} Points.

q —=—_| =g — oS Points [——~ oip switch

Figure 2-28 DIP Switch and LED Locations on the Main PCB

If you are sure that the problem is not with the video display, then try the DIP switch diagnostics shown in Table 2-

  • These tests isolate various ICs and systems for troubleshooting. The results of the tests are indicated by the main board LEDs or on the video display screen. The DIP switch settings for each test are shown in Table 2- 9, along with the explanation of the test and the results.

To set the DIP switches for the tests: 1, Put a jumper across the DIAGN test points, shown on Figure 2-28.

  • Select the diagnostic test you want to use with the DIP switch settings.
  • Turn on the self-test switch.

2-20 4, Put a jumper momentarily across the RESET test points, shown in Figure 2-28.

To change to another DIP switch test:

  • Change the DIP switch settings.
  • Put a jumper momentarily across the RESET test points, shown in Figure 2-28,

To end the DIP switch testing:

  • Take the jumper off the DIAGN test points.
  • Put a jumper momentarily across the RESET test points. The DIP switch settings are off in the top position when the main PCB board is in the simulator.
Page 35

Hard Drivin’ Self-Test

Table 2-8 Using the DIP Switches

2-21

Page 36

Self-Test Hard Drivin’

N O T E S

&

Page 37

Chapter 3

Maintenance and Troubleshooting

This chapter includes maintenance, repair, and troubleshooting information for your Hard Drivin'™ simulator. The maintenance and inspection schedule is shown first, and then a table of general troubleshooting information for the entire simulator. (A troubleshooting table for each mechanical part is shown in the section for that part.) A table of the voltage levels and test points for each PCB follows this troubleshooting table. The rest of the chapter has the repair and maintenance procedures for each part. These are arranged by the name of that part.

Because of the complexity of the simulator, the hardware and software are very closely related. Generally, you can determine how a mechanical part is working by checking the Control Inputs test screen in the self-test. You get more information about the operation of some controls from the Main Board Controls menu screen.

If you are having problems with a mechanical assembly, always keep in mind your connections may not be good or you may have an electronic hardware problem. Check the Contro/ Inputs screen to narrow down the source of the problem. Also, before you take a control out of the simulator to test or repair it, first perform the Set Controls screens in the self-test, then test the control. This can correct many electronic and . electromechanical problems.

If after using these tests and screens, you decide to repair a part, the procedures for removal, disassembly, and repair are provided in this chapter for mast parts. If a part is mentioned, but not illustrated, refer to Chapter 4, IMlustrated Parts Lists, for information.

Page 38

Maintenance

Maintaining and Inspecting

Preventive maintenance includes inspecting, cleaning, lubricating, and tightening hardware. Preventive maintenance should be performed regularly, so the simulator stays in top condition, major problems are avoided, and you maximize your earnings. Preventive maintenance tasks and intervals are shown in Table 3-1.

NOTE If you repair any control in the simulator, then when you replace it you must enter the self-test and go through the Set Controls screens. If you do not do this, then your simulator may not function correctly. this chapter. Use this table if a// of your controls are acting erratically or not responding. If just one control is not functioning, go to the section in this chapter on that control and read the troubleshooting information there. Table 3-3 contains the voltage levels to the boards and the test points for those voltage levels. Problems with controls, video, and software may be caused by low voltages to the boards associated with them.

Dashboard Removing the Dashboard

Remove the dashboard to service the steering wheel or to replace the switches. See Figure 3-1.

Maintaining Your Simulator

For the best performance from your Hard Drivin’ simulator, you should check and maintain your simulator according to the times and tasks shown in Table 3-1. How to perform these items is explained later in this chapter, in the section for that part. You may want to perform these tasks more often if the simulator is heavily used. Table 3-2 is the first of ten troubleshooting tables in

WARNING The dashboard weighs about 40 pounds. Be careful when you are removing it.
  • Turn off the power and unplug the game.
  • Take off the under-dash cover. This is a cover above the brake and clutch pedals which covers the end of the steering assembly, It is held in place by two Phillips-head screws. See Figure 4-1 for an illustration. Table 3-1 Maintenance and Inspection Items

Part E Steering Wheel © ~~

Key Switch* 2 Brake and Clutch Pedals. Shifter.

Gas Pedal

Coin Mechanism

Interior Compor

Game Exterior,

‘What to Check and Maint

3-2

Page 39

Table 3-2 Troubleshooting All Controls Maintenance

  • Remove the four nuts on either side of the dashboard and take out the carriage bolts.
NOTE Do not remove the four tamperproof screws around the steering wheel unless you are replacing the steering assembly. In that case, remove the bolts only after the dashboard is out of the simulator.

4, Remove the two tamperproof screws in the middle of the dashboard. Unlock the bottom service door to reach the nuts on the carriage bolts underneath the dashboard at we the rear. Take off the nuts and washers.

  • Also from the rear, disconnect the four connectors from the dashboard to the simulator harness.
  • Remove the two Phillips-head screws on front and the six Phillips-head screws under the dashboard.
  • The dashboard is now supported by the top lip and the side panels. Sit in the simulator seat and pull the dashboard forward and out of the simulator onto your lap.

Installing the Dashboard

  • Sit in the seat with the dashboard in your lap. Pull the seat towards the video display. Lift up the dashboard and slide it on the side panels towards

Table 3-3 Voltage Inputs and Test Points on the Simulator PCBs

Page 40

Maintenance

the mounting area.

  • Feed the dashboard harnesses through the front panel cutouts. Push the dashboard into place.
  • With one person holding the dashboard, another person can put the carriage bolts in on either side. The person sitting in the simulator can then put on the washers and the nuts. Go around to the back of the simulator and connect the steering assembly and the switch harnesses to the simulator harness. Then install the two carriage bolts with washers and nuts under the dashboard at the rear.

Install the two tamperproof screws and washers. Finally install the eight Phillips-head screws.

Not Shown: bait a oe 176025-3620 A046327-01 ier 1/4-20 Tamper- Key Switch Harmess Assy 78-051B 3/6 Interlock Washer proof Screw 177010-240 (4 places) 75-015F #10-24 Locknut 1/4 Washer

A046460-01 Steering Assy 7 (See Figure 4-5) A046445-01

75-5520B Carr. Bolt 177000-144 1/4 Hex Nut 75-055B 177024-0144 1/4 Interlock ‘V4-20 Nut Washer 75-07002 75-0558 1/4 Fender Lock Washer Washer 77012-1141 Push-On Spring Nut

046408-01 75-5520 \ Ctrl Panel Carriage Bolt Decal

160052-001 036895-01 Pushbutton Switch Bezel ‘Switch 178233-002 “Seat Adjust” agqg3z8-01 Button W/ Push-Button Hamess 160044-001 Assy Snap-Action ‘Switch Key Switch Assy (See Figure 4-4) 176020-212 +#8 Phillips- Head Screw

75-5123 #10-24 Carriage Bolt

175002-001 0.750" Shaft Washer 177010-260 3/16 Nut

046459-01 046457-01 * Senne Steering Wheel Center Decal Wheel Hub 75 gas 1/4 Lock Washer 75-8512 Socket-Head Screw

178099-005 Steering Wheel

Figure 3-1 Removing and Installing the Dashboard

3-4

Page 41

Install the under-dash cover above the brake and clutch pedals. Screw in the two Phillips-head screws that hold it in place.

  • Close and lock the service door. we

Steering Assembly

If you have problems with the steering assembly, check the troubleshooting suggestions in Table 3-4. Always perform the Set Controls screens in the self-test. If that doesn’t work, then check the Control Inputs screen,

Greasing the Steering Assembly

The steering assembly threads and stop should be greased regularly according to the maintenance schedule, and if turning the steering wheel becomes difficult (and the problem is not the steering motor).

  • Take out the dashboard. See the procedure in the section Removing the Dashboard.
  • Grease the large threads on the stop assembly. See Figure 3-5.
  • Put the dashboard back in. See the procedure in the section Installing the Dashboard. Maintenance

Replacing the Steering Assembly Potentiometer

Replace the potentiometer after you have followed the flowcharts in Figures 3-2, 3-3, or 3-4 and have decided that the source of the problem is the potentiometer. You also should replace the potentiometer if the steering wheel can spin freely in one direction or another with no end stop. (In this case, also replace the stop assembly.)

  • Take out the dashboard. Follow the instructions in the section Removing the Dashboard.
  • The steering wheel is illustrated in Figure 3-5 Loosen the set screw that holds the potentiometer shaft in place. Remove the nut that holds the potentiometer in the potentiometer bracket. Take out the potentiometer. If the small spring that holds the potentiometer bracket on the stop bracket is broken, replace it too.
  • Solder the wiring harness to the new potentiometer. Connect the wires in this order: red nearest the shaft, clear in the middle, and black at the end.
CAUTION It is very important that you follow the instructions for installing the new potentiometer. If you do not, you might destro y the potentiometer.

Table 3-4 Troubleshooting the Steering Assembly

Steering wheel is turned all the way, the other during play and stays ther:

  • Replace the stop ‘assembl
Page 42

Maintenance Hard Drivin’

‘Steering wheel has no feedback ‘during game play (although you can play the game) and you have already tried the Set Controls screen,

‘On the Control inputs sereen the top steering whee! line appears ‘smoothly tothe right as you turn the steering wheel clockwise, Does the voltage at the steering wheel input on the main board increase smoothly {rom 0 to 5 Volts when you turn the whee! clockwise? Check steering whee! harness. Check steering wheel potentiometer.

Troubeshoot the 12-bit A/D circuit ‘on the main PCB. See the main PCB schematic.

Call Atari Customer Service ‘On the Control inputs screen the bottom whee! line appears smoothly to the right as you turn the steering whee! clockwise.

‘Goto the Main Board Controls serean and choose the Steering Wheel item. Choose the Send Force| Tesi from the submenu.

Do you get the proper force on Check the resistance to the motor . the steering when its cold. The resistance Is the resistance too high or oo wheel? should be between 6 and 12 2. tow?

‘Check the resistance of the thermal protect on the motor. (Test across the two wires coming out of the motor labelled TP.) Check the 8-bit A/D circuit on the main PCB, See the main PCB ‘schematic.

Is the thermal protect an open circuit’ Replace motor.

CAUTION 1. Check the fuses on the motor amplifier ‘The circuitry is not isolated trom the PCB, If they are blown, replace them. ‘main ine, even thoughit may appear 2. If they blow again, replace the motor that way. Unplug the game and walt 5 ‘amplifier assembly. You must return the mminstes before removing the the motor ‘motor ampilior assy to Atari Games amplifier assembly from tre game, ‘Customer Service for repair.

Figure 3-2 Steering Wheel Has No Feedback and You Have Tried the Set Controls Screens

3-6

Page 43

Hard Drivin’ Maintenance

Steering wheel is tumed all the way clockwise or counterclockwise during game play and you have already tried the Set Controls screen.

(On the Control inputs screen, the steering wheel line appears smoothly to the right as you turn the steering wheel clockwise,

Does the voltage at the steering wheel input on the main board increase smoothly from 0 to 5 Volts when you tum the wheel clockwise? Check the steering wheel harness. Check the steering wheel potentiometer. (On the Control Inputs screen, the whee! line at the bottom appears smoothly to the right as you tum the steering whee! clockwise. Yes

Troubleshoot the 12-bit A/D circuit on the main PCB. See the main PCB schematic.

Troubleshoot the 8-bit A/D circuit on the main PCB. See the main PCB schematic.

Go to the Main Board Controls screen and go into the steering Wheel menu. Choose the triangle wave test. CAUTION

The circuitry is not isolateatrom the main line, even though it may appear that way. Unplug the game and wait 5 minutes before removing the the motor amplifier assembly from the game.

Does the steering wheel force change smoothly from clockwise to counterclockwise when you do the triangle wave test? Hold the steering wheel when you do this test. Check the motor amplifier PCB fuse and the cable from the main board to the motor amplifier assembly. If you think the problem is on the motor amplifier assembly, you must return the entire assembly to Atari Games Customer Service for repair.

Call Atari Customer Service

Figure 3-3 Steering Wheel is Turned All the Way to One Side or the Other and You Have Tried the Set Controls Screens

Page 44

Maintenance

Steering wheel is very jerky and you have already tried the Set Controls screen.

On the Controls Inpul screen, the steering wheel line appears smoothly to the right as you turn the steering wheel clockwise.

‘On the Controls input screen, the wheel line at the bottom appears smoothly to the right as you turn the steering wheel clockwise.

Go to the Main Board Controls screen anid go into the steering wheel menu. Choose the triangle wave test. ‘Check the installation of the potentiometer. Replace the potentiometer. Troubleshoot the 12-bit A/D circuit on the main PCB.

‘Troubleshoot the &-bit A/D circuit on the main PCB.

CAUTION ‘The circuitry is not isolateatrom the main line, even though it may appear that way. Unplug the game and wait 5 minutes before removing the the motor amplifier assembly from the game.

Boos the force change ‘smoothly from clockwise to counter- clockwise when you do this test? (Hold the steering wheel to feel the force change.) Check the motor amplifier PCB fuse and the cable from the main board to the motor amplifier assembly. If you think the problem Is on the motor amplifier assembly, you must return the entire assembly to Atari Games Customer Service for repair.

Figure 3-4 Steering Wheel Is Very Jerky and You Have Tried the Set Controls Screens 4 Hold the new potentiometer with the shaft facing you and turn its shaft as far as it can go in the counterclockwise direction. Then turn the shaft back about 15 degrees clockwise.

  • Face the stop bracket on the end of the motor; then turn the motor shaft as far as it will go in the clockwise direction.
  • Install the potentiometer in the potentiometer bracket on the end of the motor with the flat of the potentiometer shaft under the set screw and the potentiometer key in the keyhole in the bracket. If the flat part of the shaft is not under the set screw,

3-8 then repeat steps 5 and 6.

Put the lock washer and nut on the potentiometer bracket and tighten the nut. Be sure you do not turn the potentiometer shaft from the position at which you set it.

Insert the potentiometer shaft into the motor shaft; tighten the socket-head set screw. Check the alignment of the potentiometer and the motor by very carefully turning the steering wheel as far as it will go clockwise and counterclockwise. Check to see that the potentiometer does not come to its own stop, but continues to turn as far as the

Page 45

steering wheel turns in both directions. If the potentiometer does come to its own stop, then do steps 4 through 8 again.

  • Put the dashboard back in the simulator, following the instructions in the section Installing the Dashboard.
  • Go to the Set Controls screens in the self-test and re-initialize all the controls.
NOTE You must go through the Set Controls screens in the self-test because the steering wheel has been repaired. If you do not do this, the simulator wiil not function correctly.

Replacing the Steering

Wheel Motor

Replace the steering wheel motor if you have followed the flowchart in Figure 3-2 and determined that the motor is the source of the problem. Another reason to replace the motor is if the steering wheel is very difficult to turn and the problem is not lubrication or the mechanical parts. Before you replace the motor, check the harness connections to make sure they are good.

  • Take out the dashboard. Follow the instructions in the section Removing the Dashboard.
  • The steering wheel is shown in Figure 3-5. Do not take the steering assembly off the dashboard yet.
  • Carefully peel off the Atari Games decal on the hub of the steering wheel. 4, Unscrew the socket-head screw under the decal. Remove the screw, the washer and the hub cover.
  • Remove the large nut under the hub cover with a 1 1/16-inch socket. The nut is tightened to 50 footpounds,
  • Take off the washer and the steering wheel.
  • At the other end of the steering assembly, remove the potentiometer from the end of the shaft by loosening the set screw at the end of the shaft. Take off the potentiometer and the potentiometer bracket.
  • Remove the nut at the end of the motor shaft which holds the stops on the shaft. This nut also requires a 1 1/16-inch socket and is torqued to 50 foot-pounds. Remove the washer.
  • Remove the four tamperproof screws that hold the steering assembly on the dashboard. Take the 10.

12.

13.

14,

15.

16.

an

18.

19.

20. Maintenance

steering assembly off the dashboard. Use a puller to loosen the stop assembly on the tapered shaft. You cannot remove the stop assembly until you take the stop bracket off. . Remove the four socket-head screws and washers that hold the stop bracket on the motor. Pull the stop bracket and the stop assembly off the motor shaft. Do the following tasks before you re-assemble the parts on the new motor: a.Check the round stops on the corners of the large rectangular stops. Make sure the round stops are not cracked or broken. b. Tighten the socket-head screws that hold the rubber stops in place. c. Generously grease the threads. d.Check the spring that holds the potentiometer shaft on the stop bracket. If it is broken, replace it. Put the threaded center stop into the holes in sides of the stop bracket. Push the stop bracket and the stop assembly on the shaft of the new motor. (The nut on the end of the shaft will properly tighten the stop assembly.) Make sure you position the key slot over the key. Screw the four socket-head screws and washers into the stop bracket and motor. Make sure you reconnect the ground wire, with the wide washer, under the top left screw. Replace the nut and the washer at the end of the motor shaft that holds the stops on the shaft. Torque the nut to 50 foot-pounds. Set up the potentiometer position and shaft position. Hold the potentiometer with the shaft facing you and turn its shaft as far as it can go in the counterclockwise direction. Then turn the shaft back about 15 degrees clockwise.

  • Face the stop bracket on the end of the motor; then turn the motor shaft as far as it will go in the clockwise direction. Install the potentiometer in the potentiometer bracket on the end of the motor with the fiat of the potentiometer shaft under the set screw and the potentiometer key in the keyhole in the bracket. If the flat part of the shaft is not under the set screw, then repeat steps 16 and 17. Put the lock washer and nut on the potentiometer bracket and tighten the nut. Be sure you do not turn the potentiometer shaft from the position at which you set it. Insert the potentiometer shaft into the motor shaft; tighten the socket-head set screw.
Page 46

Maintenance Hard Drivin’

yest ‘Grease #8-32 Hex- Head Screw 046454-01 3-Rotation 72-8512 St

  • 178026-015 Ta20 Sera Extension Spring 1/4 Lock Washer 75-0188 1/4 Flat Washer 046462-01 Rubber Stop (1 Place) 177010-260 046463-01 Rubber Stop Brkt 3/4 Nut 178181-7806 Stee! Spacer (4 places) ‘A046332-01 175002-001 Motor Assy 046457-01 Flat Washer teres A046331-01 Hub Steering Assy Harness

175002-001 046456-01 72-8610 Washer Pot Bracket —#8.32 Screw 177010-241 Screw 75-0188 Washer 177010-241 ‘+7000!

Steering ‘Wheel

046459-01 Hub Decal

177010-260 Locknut

046458-01 75-0458 Hub Cover Washer

Figure 3-5 Maintaining the Steering Wheel

  • Check the alignment of the potentiometer and the motor by very carefully turning the steering wheel as far as it will go clockwise and counterclockwise. Check to see that the potentiometer does not come, to its own stop, but continues to turn as far as the steering wheel turns in both directions. If the potentiometer does come to its own stop, then do steps 15 through 20 again.
  • Using the four tamperproof screws, install the steering assembly on the dashboard. Tighten the nuts on the carriage bolts securely so the steering assembly will not twist on the dashboard. . Install the steering wheel on the steering hub. Make sure the hole in the steering wheel goes over 2: &

3-10 the alignment stud on the hub. (See Figure 3-5.)

  • Put on the washer and the large nut. Torque the nut to 50 foot-pounds.
  • Install the hub cover, split-lock washer, and the socket-head screw. Put Loktite on the screw before installing it and then tighten it to 95 inch-pounds.
  • Replace the Atari Games decal on the hub.
  • Put the dashboard back in the simulator, following the instructions in the section Installing the Dashboard.
  • Go to the Set Controls screens in the self-test and te-initialize all the controls.
Page 47
NOTE You must go through the Set Controls screens in the self-test because the steering wheel has been repaired. If you do not do this, the simulator may not function correctly.

Replacing the Steering Wheel Stop

It is very unlikely that the steering wheel stop will have to be replaced. If it does, follow the instructions in Replacing the Steering Wheel Motor for assembly and disassembly.

Key Switch Assembly

Table 3-5 lists the few things that can go wrong with the key switch assembly. You should regularly oil the assembly.

Oiling the Key Switch Assembly

The key switch bezel ring and shaft should be oiled regularly, or when turning the key switch becomes difficult or the key squeaks.

  • Take out the dashboard. See the procedure in the section Removing the Dashboard.
  • Lightly oil the bezel, shaft, and spring of the key switch. See Figure 3-6. Check to make sure the spring is not broken. If it is, then replace the spring following the procedure under Repairing the Key Switch.
  • Put the dashboard back in. See the procedure in the section Installing the Dashboard, Maintenance

Replacing the Spring in the

Remove the dashboard. Follow the procedure in the section Removing the Dashboard.

  • Take the key switch assembly off the dashboard by removing the two carriage bolts and locknuts.
  • Start disassembling the key switch by removing the retaining ring from the back of the case.
  • Loosen the socket head screw on the brass actuator with a 5/32-inch Allen head wrench. This screw tightens the actuator on the shaft.
  • Remove the other retaining ring inside of the case. Pull out the key. Take out the brass actuator, the old spring, and the nylon washer.
  • Put one end of the spring into the hole in the side of the case. Push the shaft back into the case far enough to mount the spring on the shaft. You may have to cut the legs of the spring to the correct length so that they do not interfere with the operation of the assembly.
  • Put the brass actuator into the case. The pin on the actuator should face the key and be on the opposite side of the assembly from the switch. Catch the free end of the spring under the pin. Install the nylon washer and the actuator on the shaft.
  • Push the shaft through the case and install the two retaining rings. Position the actuator on the shaft so that it lines up with the roller on the switch. Tighten the socket-head screw on the actuator.
  • When the brass actuator is against the case opposite the switch, the key should be straight up and down. If the key isn’t straight up and down, loosen the screw on the actuator. Turn the key until it is straight up and down. Tighten the screw on the actuator to hold it in place on the shaft.
  • Now tuin the key so the actuator is against the case on the same side as the switch. Release the key, hold the actuator against the switch, and adjust the position of the switch. The switch must be close enough so that the actuator engages the

Table 3-5 Troubleshooting the Key Switch

3-11

Page 48

Maintenance

Not Shown: 172020-0614 Spring Pin 72-8006 #10-32 Socket-Head ‘Screw 75-040S #10 Split-Lock Washer

046450-01 Actuator 75-0408

Washer 175009-364 Nylon Washer

178001-004 Retaining Ring

160045-003 Switch

7214128 4046327-01 #4-40 Phillips- Key Switch Head Screw Hamess Assy 75-0148 #4 Washer 177010-292 #4-40 Nat #10 Lock 176008-110 #10-32 Socket- Head Screw

046449-01 Shaft

178256-001 Torsion Spring 178001-004 Retaining Ring

046446-01 Housing

046448-01 Key

Figure 3-6 Maintaining the Key Switch Assembly

switch, but not so close that the actuator can make it click twice when the key is turned.

  • Release the actuator and try turning the key to make sure that this is the correct setting. Tighten the screws on the switch when the distance is correct.
  • Put the key switch assembly back on the dashboard. Install the dashboard as described in the section Installing the Dashboard.

3-12 Tightening the Screw in the Key Switch Assembly Actuator Remove the dashboard. Follow the procedure in the section Removing the Dashboard.

  • Position the actuator on the shaft so that it lines up with the roller on the switch. Tighten the sockethead screw on the actuator with a 5/32-inch Allen head wrench so the actuator does not rotate any-

more.

  • When the actuator is against the case opposite the switch, the key should be straight up and down. If the key isn’t straight up and down, loosen the
Page 49

screw on the actuator. Turn the key until it is straight up and down. Tighten the screw on the actuator to hold it in place on the shaft,

  • Now turn the key so the actuator is against the case on the same side as the switch. Release the key, hold the actuator against the switch, and adjust the position of the switch. The switch must be close enough so that the actuator engages the switch, but not so close that the actuator can make it click twice when the key is turned.
  • Release the actuator and try turning the key to make sure that this is the correct setting. Tighten the screws on the switch when the distance is cortect.
  • Install the dashboard as ‘described in the section Installing the Dashboard.

Replacing the Switch on the Key Switch Assembly

The key switch assembly is shown in Figure 3-6. 1, Remove the dashboard. Follow the procedure in the section Removing the Dashboard.

  • Take the key switch off the dashboard by removing the two carriage bolts and locknuts.
  • Remove the two Phillips-head screws that hold the snap-action switch on the key switch assembly. Take off the switch. Take the harness off the switch. 4, Install the switch on the assembly, but do not tighten the screws. The roller on the switch should be facing in towards the brass switch actuator.
  • When the brass actuator is against the case opposite the switch, the key should be straight up and down. If the key isn’t straight up and down, loosen the screw on the actuator. Turn the key until it is straight up and down. Tighten the screw on the actuator to hold it in place on the shaft.
  • Now turn the key so the actuator is against the case on the same side as the switch. Release the key and hold the actuator against the switch with Maintenance

your hand. Adjust the position of the switch. The switch must be close enough so that the actuator engages the switch, but not so close that the actuator can make it click twice when the key is turned.

  • Release the actuator and turn the key to make sure that this is the correct setting. Tighten the screws on the switch when the distance is correct.
  • Put the harness on the new switch. The black wire must connect to the C (or COM) terminal, and the white wire must connect to the NO terminal.
NOTE If these wires are connected to the wrong terminals, the simulator will not operate correctly.
  • Put the key switch assembly back into the dashboard and install the dashboard as described in the section Installing the Dashboard.

Clutch Pedal

The clutch is part of the clutch and brake pedal assembly. The clutch potentiometer is actually located on the brake side of the assembly, but is attached to the clutch. If you have trouble with the clutch, check the suggestions in the Table 3-6, Troubleshooting the Clutch Pedal. Always perform the Set Controls screens first. If you need to repair the clutch, but you cannot do so immediately, you can disable the clutch circuit. By doing this, you can continue to operate the game although the control is not working properly. The software will compensate for the non-functioning control. This is only a temporary measure. The clutch should be repaired as soon as possible. To disable the circuit, go to the Disable Broken Controls screen in the selftest and disable the clutch.

Table 3-6 Troubleshooting the Clutch Pedal

3-13

Page 50

Maintenance

Go to Control inputs screen inthe self-test

Does the 8-bit A/D tine for the contro! move smoothly when you operate the control? Do the other lines on the ‘screen move smoothly when those other controls are operated? Troubleshoot the &-bit A/D circuit on the main PCB.

Check the ZRAM in Special Functionsin the self-test.

‘Are the gears, springs, and/or cables connected to the potentiometer, working, and lubricated?

Is the potentiometer installed correctly and the nut tight?

Check the voltage at the control input to the main PCB. ‘See the schematics,

Does the voltage input Replace the vary when you potentiometer operate the control?

Troubleshoot the 8-bit A/D ircuit on the main PCB.

Figure 3-7 Clutch, Seat, or Gas Pedal Is Not Working or Working Erratically 4 and You Have Tried the Set Controls Screens 3-1

Page 51

Oiling the Clutch and Brake

Pedals

You can oil six of the pedal bearings from the back of the simulator without taking the pedal assembly out. However, you must take the pedals out of the simulator to reach the other two. We recommend that you remove the pedal assembly to oil all the points so you do not get oil on the PCBs below the pedals.

  • Remove the pedals from the simulator. First, take off the cover above the pedal assembly in the front of the simulator. Use a Phillips screwdriver to remove the four screws that hold the cover on. N Unlock the bottom service door. Take off the harness connector to the pedal.
  • The back of the pedal assembly is above the main board. Remove the four nuts and fender washers holding the pedal assembly to the cabinet. After you remove the nuts, the pedals will continue to hang in the same position.
  • Go to the front. Holding the pedal shafts, twist and pull the assembly counterclockwise to avoid the bottom of the dashboard.
  • Put light oil on the eight bearing points illustrated in Figure 3-8.
  • Check the following on the brake switch and actuator. a.Can you push the brake pedal 1/4 to 1/2 inch before you feel resistance? If you feel resistance before this point, check the bearings to see if they are moving freely. If the bearings are moving, adjust the nut on the brake spring return shaft so that the pedal has at least 1/4 inch of free play. b.Does the pedal return to its resting location? If not, check if the return spring is broken or the bearings are binding. c. Does the brake pedal move at least 1/4 inch before the switch clicks? If not, adjust the clamp on the white plastic actuator until you have 1/4 inch of play in the pedal. Make sure the switch clicks before you feel resistance on the pedal.
  • Put the pedal assembly back in the simulator. Install the fender washers and the locknuts. Re-connect the simulator harness.

Replacing the Clutch

Potentiometer

Do not replace the potentiometer until you have performed the Set Controls screens. If that does not solve the problem, follow the flowchart in Figure 3-7 to make sure that the potentiometer is the problem. we

10.

i ia

12. Maintenance

. Take off the cover above the pedal assembly in the front of the simulator. Use a Phillips screwdriver to remove the four screws that hold the cover on the cabinet. . Unlock the bottom rear service door. The back of the pedal assembly is above the main PCB. Disconnect the simulator harness from the assembly. Remove the washers and nuts holding the pedal assembly to the cabinet, After you remove the nuts, the pedals will continue to hang in the same position. . Go to the front of the simulator. Holding the pedal shafts, twist and pull the assembly counterclockwise to avoid the bottom of the dashboard. . See Figure 3-8 for an illustration of the pedals. The clutch potentiometer is on the end of a small gear and is mounted on the brake side of the pedal assembly. Loosen the locknut on the potentiometer with a 1/2-inch flat wrench. Loosen the set screw on the small gear with a 3/32inch Allen wrench. . Take off the gear, nut, washer, and potentiometer. Take the wires off the potentiometer. With the shaft of the new potentiometer facing you and the terminals pointing up, solder the black wire on the left terminal, the yellow on the middle, and the red to the right terminal. Put on the new potentiometey. Make sure the key on the potentiometer is inserted into the key hole in the assembly frame. The potentiometer terminals must point up. Put the nut and washer on, but do not tighten the nut all the way. Put the gear on the potentiometer shaft. The set screw must be straight up and located on the flat part of the shaft. Make sure that the gear completely meshes with and is directly over the gear below. Tighten the set screw. Tighten the nut on the potentiometer. Carefully press the clutch pedal and make sure that the potentiometer does not reach its stop before the pedal reaches its own stop. If it does, re-install the potentiometer, following steps 8 and 9. .Put the pedal assembly back in the simulator. Install the fender washers and the locknuts. Re-connect the simulator hamness. Now switch on the self-test and go through the Set Conirols screens.

NOTE You must enter the self-test and go through the Set Controls screens because you have repaired the pedal assembly. Otherwise the simulator will not function correcily.
Page 52

Maintenance

Not Shown:

emrs¥79012-004 te PedalLubricate on both
ipRing onClutchShatt& Pedaly4

17602-3504 ends of shafts. Set Screw on 60-Tooth Gear 107013-001 Light Oil

72-8612 Socket-Head Screw 177010-236 046393-01 Nut

Sumper Bad~jean Tae046379-01
©17602-3604gasaoi-o1|clutch Bearing

Spring Tab Housing 046391-01 Clutch Link 046385-01 Clutch Spring Housing br ona Poe ‘os6300.014 72-8612 #6-32 Pan-Head ‘Screw 046386-01 177010-236 Gluten

46-32 NutShaft046396-01

75-0168 Brake End

#6 Washer046395-01Cap
178181-3604Soing shatBrake Com-
1/4-Inch SpacerHear Coverpression

_| Spring 177000-147 +#5/16-24 Nut 72-8808 1 106007-001 san Loktite 290 #8-32 Screw Guide Cap 046399-01 046394-01 Brake Rod Spring Front Shaft Cover 046398-01 Urethane Brake Spring 040249-01

Spur Gear | “ya-g612 Socket-Ha Screw 178181-3604 1/4-Inch Spacer 040235-01 60-Tooth Spur Gear ) 178026-016 Clutch Exte 177010-236 46387-01 E Nut 4" Clutch f Spring Shaft 046387-01 4" Clutch Spring Shaft ; ‘4046330-01 S 1190084001 Brake & 5 KQPot Cluteh 046392-01 Harness

046383-01Brakei004

Clutch Pedal Switch fe Clip Ring 17824-2209 Actuator

Actuator A 75-5540B Crane Pedal Pivot 1/4-20 Carriage Bolt 160044-001 é Shaft 177012-111 Brake Switch J Push-On Spring Nut

72-8414i-75-0702
‘Sorew‘A046499-01Strain GaugeFender Washer
177010-232Brake Pedal Assy477010-244

44-40 Nut (includes strain gauge and 1/4-20 Nut strain gauge harness) Figure 3-8 Maintaining the Clutch and Brake Assembly

3-16

Page 53

Replacing the Clutch Springs

Replace the clutch springs if the clutch does not return to position and the springs are weak or broken. See Figure 3-8 for an illustration of the pedals. The clutch springs are the two large side-by-side metal springs.

  • Take off the cover above the pedal assembly in the front of the simulator. Use a Phillips screwdriver to remove the four screws that hold the cover on the cabinet.
  • Open the bottom rear service door. The back of the pedal assembly is above the main board. Disconnect the simulator harness from the assembly. Remove the washers and nuts holding the pedal assembly to the cabinet. After you remove the nuts, the pedals will continue to hang in the same position.
  • Go to the front of the simulator. Holding the pedal shafts, twist and pull the assembly counterclockwise to avoid the bottom of the dashboard. 4, Remove the metal stop bracket with the rubber bumper pads attached to it. Take out the two socket-head screws, one on either side, which hold the bracket to the frame. (You do not need to remove the rubber bumper pads.) Pull the stop bracket out the assembly.
  • Take off the locking tabs on the end of the spring shafts. Use an Allen wrench to remove the sockethead screws on the tabs. Maintenance
  • Push the shafts through the assembly frame and remove the springs.
  • Install the new springs, making sure the ends are located in the cut-out areas on the nylon shaft covers,
  • Push the spring shafts back into place and reinstall the locking tabs.
  • Install the stop bracket. Make sure the pedal shafts are resting on the rubber bumpers.
  • Put the pedal assembly back in the simulator. Install the fender washers and the locknuts. Re-connect the simulator harness.
  • Now switch on the self-test and go through the Set Controls screens.
NOTE Enter the self-test and go through the Set Controls screens when you replace the pedal assembly. Otherwise the simulator will not function correctly.

Brake Pedal

The brake is part of the clutch and brake pedal assembly. If you are have trouble with the brake, check the suggestions in the Table 3-7, Troubleshooting the Brake Pedal. Always perform the Set Controls screens first.

Table 3-7 Troubleshooting the Brake Pedal

3-17

Page 54

Maintenance

‘You have tried the Set Controisscreens. Go to Control inputssereen in the selltest

Does the LED on the Brake PCB dim when the brake Is pressed hard? Does the Brake Force line change when you operate the control?

‘Check the connectors and the cable to the main PCB at the pin on the main PCB. Does the voltage fall when the brake is pressed hard?

Troubleshoot the 12-bit A/D circuit on the main PCB. Is the ZRAM on the main PCB good?

Call Atari Games Customer Service. Is the fuse F4 on the power supply good?

Check the connectors to the brake board and to the switch.

Check the power to the brake PCB,

Check the switch actuator distance.

‘Check if the switch is good ‘and connected properly,

Check the strain gauge and the strain gauge bonding.

or replace the cables cr connectors.

Figure 3-9 Brake is Not Working or Working Erratically and You Have Tried the Set Controls Screens

Oiling the Brake Bearings

Follow the procedure under Oiling the Clutch and Brake Bearings. While you have the clutch and brake pedal assembly out, also check the actuator and resistance settings on the brake, explained in Oiling the Clutch and Brake Bearings.

Maintaining the Brake

These are the routine procedures you should do every three months and whenever you have the pedal assembly out of the game

  • Take off the cover above the pedal assembly in the front of the simulator. Use a Phillips screwdriver to remove the four screws that hold the cover on the cabinet. Open the lower rear service door. The back of the pedal assembly is above the main PCB. Disconnect the simulator harness from the assembly. Remove the washers and nuts holding the pedal assembly to the cabinet. After you remove the nuts, the pedals will continue to hang in the same position. Go to the front of the simulator. Holding the pedal shafts, twist and pull the assembly counterclockwise to avoid the bottom of the dashboard.

3-18

  • See Figure 3-8 for an illustration of the pedal assembly. The brake switch is located on the inside wall, under the switch actuator. Check the following: a.Check the actuator adjustment. You should be able to move the pedal at least 1/4 inch before the switch clicks. If not, adjust the clamp on the white plastic actuator until you have 1/4 inch of play in the pedal. Make sure the switch clicks before you feel resistance on the pedal. b.Resistance on the pedal should begin after the switch clicks, but no further than 1/2 inch from the starting point. If you feel resistance before this point, check if the bearings are moving. If the bearings are moving freely, adjust the nut on the brake spring return shaft so that the pedal has at least 1/4 inch of free play, and the switch clicks before the resistance begins.

Repairing the Brake

The brake may not function for several reasons. Before you do any repairs, always perform the Set Controls screens in the self-test; then try the brake to see if this corrects the problem. If not, then follow the flowchart in Figure 3-9. The test procedures mentioned in the flowchart are explained below.

Page 55

If the brake must be repaired, but you cannot repair it immediately and you want to continue to use your game, you can disable the brake circuit. This ‘is only a temporary measure. You should repair the brake as soon as possible. To disable the brake circuit, go to the Disable Broken Controls screen in the self-test and choose the brake.

Check Switch, Switch Actuator and Pedal Movement If the brake is not working at all, you should check the following. (Check the flowchart in Figure 3-9.)

  • Check the actuator adjustment. You should be able to move the pedal for at least 1/4 inch before the switch clicks. If not, adjust the clamp on the white plastic actuator until you have 1/4 inch of play in the pedal. Make sure the switch clicks before you feel resistance on the pedal.
  • Resistance on the pedal should begin after the switch clicks, but no further than 1/2 inch from the starting point. If you feel resistance before this point, check if the bearings are moving. If the bearings are moving freely, adjust the nut on the brake spring return shaft so that the pedal has at least 1/4 inch of free play, and the switch clicks before the resistance begins.
  • If the pedal does not return to its resting location, check if the return spring is broken or if the bearings are not moving.
  • Check the switch. Disconnect the connector from the Brake PCB and connect an ohmmeter across pins 6 and 7 of the harness connector. If the switch is good, the switch is closed when the pedal is not pressed, and is open when the pedal is pressed.

Strain Gauge Check the strain gauge in the self-test on the Contro! Inputs screen. The strain gauge response is measured under the Force Brake item. The harder you press on the brake, the more that the brake force line will disappear. (The position of the brake is not measured in this test.) To check the strain gauge, remove the connector from the brake PCB in the back of the simulator and put an ohmmeter across pins 1 and 2 of the harness connector. If the ohmmeter does not measure 350 Q + 10%, then replace the strain gauge and brake pedal. If the ohmmeter does measure 350 Q + 10%, then check the bonding. Attach a digital volt-ohmmeter to pins 1 and 2 and have someone press very hard on the brake. If the resistance does not change as the pressure on the brake pedal changes, then the bonding has failed. If the resistance does change, then your problem is elsewhere. Maintenance

If either the strain gauge or the strain gauge bonding has failed, you must replace the brake pedal.

Replacing the Brake Switch

Before you replace the brake switch, do the Set Controls screens in the self-test, follow the flowchart in Figure 3-9, and the steps under Repairing the Brake. If you are sure that the problem is the switch, do the following procedure.

  • With the pedal assembly out of the simulator, remove the two nuts that hold the switch against the wall. Take out the screws and the switch.
  • Replace the switch in the same position, with the terminals pointing towards the top of the pedal assembly. After the nuts and screws are installed and the switch is in place, adjust the actuator position so that the brake pedal has at least 1/4 inch of play in it before the switch clicks. Loosen or tighten the clamp on the white plastic actuator to adjust this distance. Also make sure that the switch clicks before you feel resistance when you push the pedal.
  • Re-connect the wiring assembly to the switch. The two wires attach to the C and NC terminals. If you attach the wires to the wrong terminals, the brake will not work correctly.
  • Put the pedal assembly back in the simulator. Install the fender washers and the locknuts. Re-connect the simulator harness.
  • Now switch on the self-test and go through the Set Controls screens.
NOTE You must enter the self-test and go through the Set Controls screens since you have repaired the brake. Otherwise the simulator will not function correctly.

Replacing the Brake Strain

Gauge and Pedal

Before you replace the strain gauge, do the Sef Controls screens in the self-test, follow the flowchart in Figure 3-9, and the steps under Repairing the Brake. If you are sure that the problem is the strain gauge or the bonding, do the following procedure. The strain gauge is mounted on the pedal at the factoty because special bonding techniques are required. Therefore, you must replace the strain gauge and the pedal together.

  • To replace the brake pedal, take off the cover above the pedal assembly in the front of the simu-
Page 56

Maintenance

lator. Use a Phillips screwdriver to remove the four screws that hold the cover on the cabinet.

  • Open the lower rear service door. The back of the pedal assembly is above the main PCB. Disconnect the simulator harness from the assembly. Remove the washers and nuts holding the pedal assembly to the cabinet. After you remove the nuts, the pedals will continue to hang in the same position.
  • Go to the front of the simulator. Holding the pedal shafts, twist and pull the assembly counterclockwise to avoid the bottom of the dashboard. 4, Disconnect the strain gauge wires from the Brake PCB. See Figure 3-8 for an illustration of the pedals. Remove the metal stop bracket with the rubber bumper pads attached to it by taking out the two screws, one on either side, which hold the bracket to the frame. (You do not need to remove the rubber bumper pads.) Pull the stop bracket out the assembly. uw
  • Remove the retaining ring at the top of the brake shaft that holds the shaft and brake springs together.
  • Take off the locking tab on the end of the pedal pivot shaft. Use a 3/16-inch Allen wrench to remove the socket-head screw,
  • Push the pivot shaft towards the clutch. Remove the brake pedal and strain gauge.
  • Put the new brake pedal into position. Push the pivot shaft through the brake shaft and into the case. Install the locking tab and the socket-head screw.
  • Replace the retaining ring at the top of the brake shaft that holds the shaft and the brake springs together.
  • Replace the metal stop bracket. Put in the two screws that hold the bracket to the frame.
  • Re-connect the sirain gauge wires to the Brake PCB. 13, Check the following to make sure the brake is set up properly: a.Check the actuator adjustment. You should be able to move the pedal at least 1/4 inch before the switch clicks. If not, adjust the clamp on the white plastic actuator until you have 1/4 inch of play in the pedal. Make sure the switch clicks before you feel resistance on the pedal. b.Resistance on the pedal should begin after the switch clicks, but no further than 1/2 inch from the starting point. If you feel resistance before this point, check if the bearings are moving. If the bearings are moving freely, adjust the nut on

3-20 the brake spring return shaft so that the pedal has at least 1/4 inch of free play, and the switch clicks before the resistance begins.

  • Put the pedal assembly back in the simulator. Install the fender washers and the locknuts. Re-connect the simulator harness.
  • Now switch on the self-test and go through the Set Controls screens.
NOTE Enter the self-test and go through the Set Controls screens since you have re placed the strain gauge. Otherwise the simulatos will not function correctly.

Gas Pedal Assembly

The gas peda] assembly is an assembly of springs, a cable, a pulley, and a potentiometer. The most likely cause of failure is the pulley cable breaking or unwinding. Check the suggestions in Table 3-8 before repairing the gas pedal.

Lubricating the Gas Pedal

Maintain the gas pedal assembly by lubricating at the points shown in Figure 3-8.

  • From the front of the cabinet, unscrew the seven Phillips-head screws and pull the gas pedal assembly forward. Disconnect the simulator harness from the assembly. Take the assembly out.
  • Lubricate the pivot pin and surrounding area, the spring cable, and pulley with dry Teflon spray. Check to be sure that the cable is wound correctly (see the section Rewinding the Gas Pedal Pulley Cable).
  • Put the gas pedal back in the simulator and re-connect it to the simulator harness connector. Screw in the Phillips-head screws that hold it in the simulator.

Rewinding the Gas Pedal Pulley Cable

The pulley cable may become disconnected during normal use. Also if you remove or replace the cable spring, you may also have to rewind the pulley cable. Be careful not cut or fray the cable when you remove or replace it.

  • Remove the pedal assembly from the simulator by taking out the seven Phillips-head screws that hold the pedal assembly box in the simulator. Disconnect the pedal from the simulator harness.
Page 57
  • Lay the pedal assembly on the bench, with the extension spring pointing up at the back. See Figure 3-8 for an illustration of the pedal.
  • Put one end of the cable around the hook on the pedal. Thread the rest of the cable up through the hole in the base plate. 4, Wrap the cable around the pulley counterclockwise to the cap screw. Put the cable through the notch and wrap it once, clockwise, around the cap screw in the pulley. (This screw must be at the top of the pulley. If it is not, turn the pulley so it is.)
  • Bring the cable back through the notch and wrap it twice around the pulley. Be careful not to wrap the cable over itself. Hook the circular lug onto the cable spring. The spring should be stretched out. Try pushing the pedal a few times to make sure the cable returns the pedal to the rest position.
  • Lubricate the pivot pin, springs, cable, and pulley with dry Teflon spray.
  • Install the pedal in the simulator and re-connect the harness. Make sure the ground wire is attached.
  • Go to the Set Controls screens in the self-test and re-initialize all the controls.
NOTE You must go through the Set Controls screens in the self-test because the pedal has been repaired. Otherwise, the simulator will not function correctly.

Replacing the Gas Pedal Cable Spring

The gas pedal cable spring may break. Before you replace the spring, first make sure the cable is wound correctly around the pulley since this is a likely cause of gas pedal failure. 10. Maintenance

Remove the pedal assembly from the simulator by taking out the seven Phillips-head screws that hold the pedal assembly box in the simulator. Disconnect the pedal from the simulator harness. Lay the pedal assembly on the bench, with the extension spring pointing up at the back. See Figure 3-8 for an illustration of the pedal. Disconnect the cable from the cable spring. Remove the spring and replace it. Wind the cable around the pulley correctly before you put it on the spring. If the cable is frayed or cut, replace it. Put one end of the cable around the hook on the pedal. Then thread it through the hole in the base plate. Wrap the cable around the pulley counterclockwise on the left side of the pulley to the cap screw. Put the cable through the notch and wrap it once, clockwise, around the cap screw in the pulley. (This screw must be at the top of the pulley. If it is not, turn the pulley so it is.) Bring the cable back through the notch and wrap it twice around the pulley. Be careful not to wrap the cable over itself. Hook the circular lug onto the cable spring. The spring should be stretched out. Try pushing the pedal a few times to make sure the cable returns the pedal to the rest position. Lubricate the pivot pin, springs, cable, and pulley with dry Teflon spray. . Install the pedal in the simulator and re-connect the harness, Make sure the ground wire is attached. Go to the Set Controls screens in the self-test and re-initialize all the controls.

Table 3-8 Troubleshooting the Gas Pedal Assembly

3-21

Page 58

Maintenance

107012-001 Dry Teflon Spray Lubricant

039236-01 >= Pivot Pin y if Zi “a 039240-01 . \ Foot Pedal Accelerator f \ \

, i 040028-01 | \ Pedal Compression a Spring 178012-004 \ Retaining Ring \

a 039242-01 as Cable

2 039238-01 039703-01 Pulley Cable Extension Spring Cap screw of pulley must be in 7 this position when pedal is fully open (at rest).

72-8606 039704-01 +#6-32 Socket-Head Screw Pedal Extension Spring <= 039239-01 Foot Pedal Control Base » Plate

119006-1001 5 KQ Pot whtte

Red

All parts shown above make up the Foot Control Assembly, part no, A039235-03. The Foot Control Assembly is a large subassembly of the Gas Pedal Assembly, part no. A046403-01. ie

046298-01 a Not Shown: Foot Pedal Bracket 4 ‘A043947-01 ies Gas Pedal Harness Assy 177010-240 J #10-24 Locknut 75-0108 #10 Washer

Figure 3-10 Maintaining the Gas Pedal

3-22

Page 59

Replacing the Gas Pedal

Potentiometer

Replace the potentiometer if you have followed the flowchart in Figure 3-7 and decided that the potentiometer must be replaced. When you take the gas pedal out of the simulator, first check if the springs are broken or if the cable is broken or unwound from the pulley before you replace the potentiometer.

  • Remove the pedal assembly from the simulator by taking out the seven Phillips-head screws that hold the pedal assembly box in the simulator. Disconnect the pedal from the simulator harness. Nn Lay the pedal assembly on the bench, with the extension spring pointing up at the back. See Figure 3-9 for an illustration of the pedal.
  • Disconnect the cable from the cable spring. Loosen the cap nut on the pulley and remove the pulley from the potentiometer shaft.
  • Take off the potentiometer by removing the locknut with a 1/2-inch wrench. Take the wires off the potentiometer.
  • Puta new potentiometer on the bracket in the base plate, with the three terminals facing towards you and the flat of the potentiometer shaft facing up. Tighten the nut.
  • Solder the harness wires onto the potentiometer in this order: red on the left terminal, white on the middle, and black on the right. MN . Put the pulley on the potentiometer shaft and tighten the set screw in the hub on the flat of the potentiometer shaft.
  • Re-connect one end of the cable to the hook on the pedal. Thread the rest of the cable up through the hole in the base plate.
  • Start wrapping the cable around the pulley counterclockwise to the set screw. Put the cable through the notch and wrap it once, clockwise, around the cap screw in the pulley. Bring the cable back through the notch and wrap it twice around the pulley counterclockwise. Be careful not to wrap the cable over itself. Hook the circular lug onto the cable spring. The spring should be stretched out. Try pushing the pedal a few times to make sure the cable returns the pedal to the rest position. So

. Lubricate the pivot pin, springs, cable, and pulley with dry Teflon spray. B is) Install the pedal in the simulator and re-connect the harness. Make sure the ground wire is attached.

  • Go to the Set Controls screens in the self-test and re-initialize all the controls. Maintenance
NOTE You must go through the Set Controls screens in the self-test because you re placed the potentiometer. The simulator will not function correctly if you do not set the controls.

Replacing a Broken Compression or Extension Spring on the Gas Pedal

It is very unlikely that either of these springs will be sprung or fatigued. However, if either are, follow the instructions below.

  • Take the cable off the cable spring.
  • Remove the two retaining rings from either end of the pivot pin and take out the pivot pin.
  • Take out the springs. If you are replacing the compression spring, be sure that the large end of the spring is against the base plate when you put the pedal assembly together again. 4, Reassemble the gas pedal assembly. Rewind the pulley cable in the following way: a, Re-connect one end of the cable to the hook on the pedal. Thread the rest of the cable up through the hole in the base plate. b.Start wrapping the cable around the pulley counterclockwise to the set screw. Put the cable through the notch and wrap it once, clockwise, around the cap screw in the pulley. c. Bring the cable back through the notch and wrap it twice around the pulley counterclockwise. Be careful not to wrap the cable over itself. Hook the circular lug onto the cable spring. The spring should be stretched out. Try pushing the pedal a few times to make sure the cable returns the pedal to the rest position. Ww Lubricate the pivot pin, springs, cable, and pulley with dry Teflon spray before you put the assembly back in the simulator.
  • Install the pedal in the simulator and re-connect the harness. Make sure the ground wire is attached.
  • Go to the Set Controls screens in the self-test and re-initialize all the controls,

3-23,

Page 60

Maintenance

Shifter Assembly

If you have problems with the shifter, check the suggestions in Table 3-9, Troubleshooting the Shifter Assembly. If the shifter is not working properly and you cannot repair it immediately, go to the screen Disable Broken Controls in the self-test. Disable the shifter circuit so you can continue to operate the simulator. This is only @ temporary measure. You should repair the shifter as soon as possible.

Installing a New Shifter

Boot

The shifter is shown in Figure 3-12.

  • Loosen the self-locking screw in the shifter knob and take off the knob. Remove the four tamperproof screws that hold the boot cover plate on the shifter case. Lift off the boot and the cover plate. iN)

Take the foam out of the boot. > Install the foam in the new boot. Replace the boot. w Install the cover plate and the screws. Put the knob back on.

Replacing a Shifter

Potentiometer

If the shifter is acting erratically, follow the flowchart in Figure 3-10 to make sure that the problem is with the potentiometers. However, always tighten the screw on the end of the roll link and the pitch link before you replace the potentiometer. Do the Set Controls screens in the self-test to see if this solves your problem. The shifter is shown in Figure 3-12.

  • To work on the shifter you need to take the shifter out of the its case. Leave the case in the simulator.
  • Loosen the self-locking screw in the shifter knob and take off the knob. 10.

11.

12.

13. Remove the four tamperproof screws that hold the boot cover plate on the shifter case. Lift off the boot with the foam inside it, the cover plate, and the shifter gate, which has the shift pattern in it. Remove the screw on the tie wrap that holds the clutch harness on the side of the case. Unscrew the nut on the carriage bolt on the left side of the case and slip the long thin pitch bar off the bolt. Looking down inside the shifter case, push the shifter forward and back. The shifter turns on a pivot shaft which has a cotter pin on its right side. Pull out the cotter pin. Push the pivot shaft out of the shifter case through the hole on the outside of the cabinet. Use a screwdriver or a pencil. Disconnect the six-pin connector on the simulator harness from the shifter. Lift the shifter assembly out of the case. Before you replace a potentiometer, first try tightening the locknut on the end of the roll link and the pitch link. Check the shoulder screws on the thin roll bar and pitch bar. They should be tight, but allow free movement of the bar and attached link. Tightening these nuts and screws may solve your problem. Disconnect the harness from the potentiometer that you are replacing. Loosen the nut on the potentiometer shaft with a 1/2-inch flat wrench. Remove the potentiometer. Solder the harness to the new potentiometer. With the shaft facing you and the terminals pointing down, solder the black wire to the left terminal, the white to the middle, and the red to the right. Install the new potentiometer, making sure to put the potentiometer key in the key slot in the shifter. Tighten the nut. Put the shifter assembly back in the case. Attach the pitch bar to the carriage bolt at the top of the case with the locknut. Attach the simulator harness assembly. Install the screw through the tie wrap on the clutch harness on the side of the shifter case.

Table 3-9 Troubleshooting the Shifter Assembly

using the clutc!

3-24

Page 61

Hard Drivin’ Maintenance

See the section in Chapter 2, ‘Something is wrong with the shifter Shifter Screen, for details about and you have already tried the Set these steps in the self-test. Controls screen. Go to the Shifter screen in the Main Board Controls menu in the self-test.

Check the mechanical linkages. > Check the potentiometers and > t ‘On the Shitter screen

potmuimberincreases athe wires on the terminals.‘Check the strain gauge
You push te hier sha 0Check he hamess andran gauge nurhamess and connections
the right. The Y-pot numberconnections from the shifter,a0 aetemention,to the shitter PCB. Check
increase as you push theto the shifter PCB, and to theor incrementing thethe ribbon cabie from the
she78-bit A/D converter circuit onmshifter PCB to the main

ao cnn the main PCB. PCB,

‘On the Shifter screen, does the strain gauge value increase and ‘the shift lever is pushed forward? ‘Check that strain gauge Is tightly attached to the shift lever.

‘Are the mechanical detent and hinge pivot working properly?

if you increase the brake force on the Check that the magnet is

a can you ene. correctly mounted on the

increased friction as you push the bracket. Check that the shifter lever forward and back? insulator is covering the (You can only increase the force toa coils. Check the ‘maximum of 223; any number over harnesses from the The shifter should be workirig correctly. that has no effect.) magnet to the shifter I you are stil having problems, call PCB and from the shifter ‘Atari Games Customer Service. PCB to the main PCB, Check the drive circuit on the shifter PCB.

Figure 3-11 Shifter Is Not Working or Working Erratically And You Have Already Tried the Set Controls Screens

  • Line up the tube for the pivot shaft on the assembly the legs of the cotter pin. with the holes in the case for the pivot shaft. Push 14. Put the shifter gate back on, with the latch and the the pivot shaft through the holes from the inside of spring facing down. Then put the boot and the foam the cabinet. Keep the slotted end of the pivot shaft ‘on, then the boot cover plate. Install the four tamfacing towards you. perproof screws, Install the knob.
  • Once the pivot shaft is all the way through the case, 15. Go into the self-test and perform the Set Controls use a screwdriver on the slotted end to turn the screens, shaft until the holes in the shaft line up with the holes in the tube. Put in the cotter pin. Do not bend

3-25

Page 62

Maintenance

Not Shown: 177000-182 #4 Hex Nut on Latch Spring 178026017 bettie Reverse Position Latch Spring 6-008 iDaceenan Compression Spring Reverse Position Latch Bearing ones pees #8 Lock Washer #4-40 Pan-Head Screw on Latch Spring

176025-4416 1/4-20 Button-

  • Head Screw 046523-01 beset Detent Roller
046524-0172-1818Fptea7s-o1
Roller Bearing#8 Pan-Hd ScrewBootCover

477010-241 75-0288 Plate bas poesnut #8 Washer 72-0208 17701 0-234 #10 Flat Washer PLL iia 75-07007 aea7a-o1 1/4 Washer Boot

:—046560-01
2rs.046476-01Boot
8178026-019iCushion
3Detent Lever SpringShifter Gate"

eal 178192-6306 F 3 Spring Spacer

372-001275-5528B
#4i082 Screw1/4-20 Carriage

75-0408 BCE #10 Lock Washer os

Hora Washer124-20 Locknut046479-01
046525-0172-6008LCShifter Housing
Detent Lever_-#10-32 Shoulder046424-01

Sean oor Reverse Poston Loktite 290

A046329-01 19008-1001 red Potentiometer ‘pitch bar 75.85128 171087-001 4/4 Cartiage Bolt Strain Gauge 177010-244

73-00824 Cotter Pin 046482-01 Roll Link 119008-1001 Potentiometer

046481-01 Roll Bar 1/4-20 Lock Nut

046906-01 Magnet Plate

72-E802 046478-01 Pitch Link Shoulder Screw 72-8808 177000-138 Secon -138 | : Screw #8-32 Hex Nut | 046480-01 177000-138 Hinged Plate Hex Nut

177010-241 Locknut

046484-01 046472-01

046483-01Catch Platene
Pivot Shaft75. gibe0

#10 Screw 046485-01 | Magnet 177010-241 Magnet #10 Locknut Bracket Figure 3-12 Maintaining the Shifter

3-26

Page 63
NOTE You must perform the Set Controls screens because you replaced the potentiometer. Otherwise the simulator will not operate correctly.

Replacing the Shifter Magnet or Plate

If the shifter is squeaking or squealing excessively you may need to replace the magnet or the plate it rides on, To determine which one to replace, take the shifter out of its case, as described below, and check the condition of the magnet and the magnet plate. The shifter is shown in Figure 3-12.

  • Loosen the self-locking screw in the shifter knob and take off the knob.
  • Remove the four tamperproof screws that hold the boot cover .plate on the shifter case. Lift off the boot with the foam, the cover plate, and the shifter gate, which has the shift pattern in it.
  • Unscrew the nut on the carriage bolt on the left side of the case and take the long thin pitch bar off the bolt.
  • Looking down inside the shifter case, push the shifter forward and back. The shifter turns on a pivot shaft which has a cotter pin on its right side. Pull out the cotter pin. . Push the pivot shaft out of the shifter case through the hole on the outside of the cabinet. Use a screwdriver or a pencil. Disconnect the six-pin connector on the simulator harness from the shifter. Lift the shifter assembly out of the case. wu

Check the face of the magnet. If the laminates are separated or damaged, replace the magnet. If the magnet laminates look OK, then you should replace the plate that the magnet rides on.

Replacing the Magnet

  • Disconnect the wiring from the magnet to the shifter harness. N Unscrew the two locknuts that hold the magnet bracket on the hinged plate assembly. Remove the bracket, magnet, spring, and insulator.
  • Put the new magnet with the insulator in the bracket with the spring. Install the bracket on the hinged plate assembly and screw on the locknuts. 4, Connect the magnet connectors to the shifter harness. Maintenance

Replacing the Magnet Plate

Remove the two locknuts that hold the plate in place on the side of the clutch case. Take out the plate.

  • Put in the new plate with the smooth finished side out. Tighten the locknuts to hold it.

Installing the Shifter Assembly in the Case

  • Put the shifter assembly back in the case. Attach the pitch bar to the carriage bolt at the top of the case, Attach the simulator harness assembly. N Line up the tube for the pivot shaft on the assembly with the holes in the case for the pivot shaft. Push the pivot shaft through the holes from the inside of the cabinet. Keep the slotted end of the pivot shaft facing towards you.
  • Once the pivot shaft is all the way through the case, use a screwdriver on the slotted end to turn the shaft until the holes in the shaft line up with the holes in the tube. Put in the cotter pin. Do not bend the legs of the cotter pin.
  • Put the shifter gate back on, with the latch and the spring facing down. Then put the boot with the foam and boot cover plate on. Install the four tamperproof screws. Install the knob.

Seat Assembly

The movement of the seat is controlled by the seat adjust button on the dashboard and by the simulator itself. When the simulator is in the attract mode, the seat moves freely. When the key is turned to start the drive, the seat is locked, unless the seat adjust button is pushed and held while the seat is moved. For safety reasons, the seat can be pushed out of the simulator only so fast, so spectators won't be hurt. If the driver pushes the seat very hard to get out, the seat magnet will engage and slow the seat as it turns out of the simulator. The seat assembly should not require many repairs, and does not require any regular maintenance, other than checking for obstructions around the seat movement area. If you have difficulties with the seat, check Table 3-10, Troubleshooting the Seat Assembly,

Replacing the Seat Rod End Bearings

Replace both rod ends if you have difficulty rotating the seat, or the seat squeaks as it rotates. The seat assembly is shown in Figure 3-15.

3-27

Page 64

Maintenance

  • Take off both end plates of the mounting box. Each end plate is held on by four tamperproof screws. Also remove the bottom cover on the mounting box.
  • The rod ends are attached to the pivot blocks with shoulder screws. Use an Allen-head wrench and a flat wrench to remove the screws and nuts.
  • Take out the rod ends and the pivot arm. Remove both rod ends from the pivot arm. Save the nut on the right rod end.
  • Insert the right rod end into the pivot arm with the nut on the threads. The left rod end has left-hand threads and will not fit on the right end. Carefully set the rod ends and pivot arm length to the following dimensions. These dimensions must be set correctly so that the assembly operates properly. ¢ The distance between the center point of the left rod end to the point where it goes into the end of the pivot arm must be exactly 1.25 inches for clearance. wn

¢ From the center of the hole in one rod end to the center of the hole in the other rod end should be exactly 11.25 inches. Do not tighten the nut on the right rod end yet.

  • Put the rod ends and pivot arm into the seat mounting box, with the right rod end on the right side as you face the simulator. Tighten the sockethead screws and nuts to hold the rod ends on the pivot blocks.
  • Turn the mounting box until it is parallel to the front of the simulator. The seat mounting platform should be square with the mounting box now. If it is not, then rotate the pivot arm until it is. When everything is square, tighten the nut on the right rod end against the pivot arm. Check the alignment again to make sure the mounting box is parallel to the front of the simulator and the seat mounting platform is square with the box.
  • Install the end plates of the mounting box with the tamperproof screws. Put the bottom cover back on.

Replacing Bearings on the

Seat Pivot

These are the bearings that allow the seat to turn. Replace the seat pivot bearings if the seat twists or jiggles excessively or you can pull the seat up and down. The seat assembly is shown in Figure 3-15.

  • To get to the bearings, you must take the left end plate off the mounting box, underneath the seat. The end plate is held on by four tamperproof screws.
  • Using a punch, hammer out the spring pin in the seat pivot.
  • When the pin is out of the seat pivot, pull up on the seat and remove it. 4, You may need to take the seat mounting box to a machine shop to do the following items: a. Remove the old bearings. (They have been press fitted.) b.Cut down one of the new bearings to 0.6 inch long. This will be the bottom bearing. (You can use a bearing on the bottom that has not been cut down, but it may catch someone’s foot.)

Table 3-10 Troubleshooting the Seat Assembly

3-28

Page 65

‘The seat is not locked when it jould be and you have already iad the Set Controls sc

Perform the seat magnet test in the Contra! Inputsin the selt-test.

Seat locks in seat magnet test

Does the seat release switch work right?

Goto the flowchart in Figure 37.

Repair seat movement assembly Measure the voltage on ihe seat ‘magnet while you periorm the ‘seat magnet test in the Control Inputs in the sel-test.

‘The voltage measure at ‘Check the seat magnet contro! least 3 Volts, transistor on the APU PCB ‘mounted on the Power Supply

's the seat magnet in contact with the magnet plate onthe tloor of the Maintenance

Is the transistor good?

game?

Check seat control voltage ‘output on the main PCB.

Figure 3-13 Seat is Not Locked When It Should Be And You Have Already Tried the Set Controls Screens

c.Turn the bearings, if necessary, to press them on the pivot of the seat mounting plate. d.The inner diameter of the bearings should be turned so that:

  • The shaft with a diameter of 1.249 inches should rotate freely when a torque of 10 inch pounds is applied.
  • The shaft with a diameter of 1.254 inches must not be able to pass through the bearings. Insert the pivot through the new top bearing, the spacer tube, the pivot block, two washers, and the new bottom bearing. uw 6.

7. Line up the holes for the spring pin in the seat pivot with the holes in the pivot block. Make sure the seat is facing the tight direction. Put in the spring pin. (You might want to use a 3/8-inch shaft or shoulder screw to hold the alignment while you are putting in the spring pin.) When the pin is in, make sure it is is flush with the outer edges of the pivot block. Put the end plate back on and install the four tamperproof screws.

Page 66

Maintenance Hard Drivin’

‘The seat is locked when’ should ot be and you have already tried the Set Controls. screen.

Does the seat unleckS Check the seat release switch ‘when you push the seat 7: redeate bution? and the ewitch harness. Is the seat locked in attract mode? power is of?

‘Check for obstructions around Priorm the seat magnet tet in Pectorm the seat magnet testin the seat and on the seat magne the Control Inputs in the piae, Thon check fhe rod ead tne Control inputs screen inthe setttest. bearings, the gears, ad all the setitest. shalt bearings.

The seat releases in the ‘Check the seat magnet contro! ‘seat magnet test. circuit on the APU PCB ‘mounted on the Power Supply “The seat releases in the Check the seat magnet control ‘seat magnet test. sircuiton the APU PCB mounted fon the Power Supply

Check for obstructions around the seat, on the magnet plato, the rod end bearings, the gears, and all the shaft bearings. Is the circuit good? Isthe circuit good?

Replace of repair the APU PCB

Check seat control voltage ‘output on the main PCB. Check seat contro! output on the ‘main PCB,

Check the seat release switch Replace or repair and the switch harness. the APU PCB Does the seat release ‘switch work right?

Goto the flowchart in Figure 37.

Figure 3-14 Seat is Locked When It Should Not Be And You Have Already Tried the Set Controls Screens

3-30

Page 67

Replacing the Main Seat Bearings

These bearings are between the base of the simulator and the seat mounting arm. Replace them if the seat mounting arm is twisting or jiggling or you can pull the arm up and down. The seat assembly is shown in Figure 3-15. To replace these bearings you must remove the simulator floor and take out the seat assembly. You will need another person to help you.

  • Take out the Phillips-head screws on the back edge of the floor tim, which is the strip of metal across the middie of the floor. Remove the three Phillipshead screws along the front of the simulator under the rubber floor mat.
  • Turn the seat out of the simulator as far as it will go. Pry up the floor by using two screwdrivers on the front corner of the floor to lift and pry.
  • Before you can take out the seat mechanism, you must take out the coin module and the shifter. Open the top and bottom coin doors and take off the four locknuts on the carriage bolts on the side of the cabinet.
  • Disconnect the simulator harness from the coin module. Remove the bolts and the coin module.
  • Now take out the shifter. Loosen the self-locking screw in the shifter knob and take off the knob.
  • Remove the four tamperproof screws that hold the boot cover plate on the shifter case. Lift off the boot with the foam, the cover plate, and the shifter gate, Disconnect the shifter harness.
  • Take off the locknuts on the two tamperproof screws and the two carriage bolts that hold the shifter on the side of the cabinet and remove the screws. Remove the shifter.
  • Disconnect the simulator harness from the seat assembly. Remove all the screws and nuis that hold the seat assembly in the simulator. Tip the seat back until the seat frame clear the floor. Push the seat assembly towards the pedals until the assembly is out from under the floor.
CAUTION The gears and potentiometer are on the bottom of the assembly under the floor in front of the license plate. Do not damage these parts when you push the seat assembly forward and up.

9 When the assembly is clear of the floor, pull the assembly out of the simulator. Maintenance

WARNING The seat assembly is heavy. Be careful.
  • Take off both end plates of the mounting box on the seat assembly. Each end plate is held on by four tamperproof screws. Also remove the bottom cover on the mounting block. . Remove the rod ends and the pivot arm from the pivot block inside the mounting box. The rod ends are attached to the pivot blocks with shoulder screws, Use an Allen-head wrench and a flat wrench to remove the screws and nuts. Take out the rod ends and pivot arm and lay the assembly aside.
  • Remove the potentiometer bracket with the potentiometer gear and small gear from the bottom of the seat assembly.
  • Remove the large half gear on the bottom of the main shaft. You may want to turn the assembly on its side to do this.
  • Using a punch, hammer out the spring pin in the bottom of the main shaft in the magnet arm. Remove the magnet arm.
  • Turn the seat until you can pull the seat mounting box off the seat assembly.
  • You may need to take the welded seat assembly to a machine shop to do the following items: a. Remove the old bearings. (They have been press fitted). b.Turn the bearings, if necessary, to press them into the main shaft on the seat. c.The inner diameter of the bearings should be turned so that: © The shaft with a diameter of 1.624 inches should rotate freely when a torque of 10 inch pounds is applied. © The shaft with a diameter of 1.629 inches must not be able to pass through the bearings.
  • Press the bearings in. (It is not necessary to oil the bearings because they are oil-impregnated.) Insert the main shaft through the top bearing, the shaft holder, the bottom bearing, and the magnet arm.
  • Line up the hole in the shaft for the spring pin with the holes in the magnet arm. Make sure the seat is facing the right direction. Install the spring pin. 19, Put the rod ends and pivot arm assembly back into the seat mounting box, with the right rod end on the right side. Tighten the shoulder screws and nuts to hold the rod ends on the pivot blocks. Do not install the end plates or the bottom cover on

3-31

Page 68

Maintenance

the mounting box until the seat assembly is back in the simulator, since you must check the alignment with the seat in the simulator.

  • Install the potentiometer bracket tightly on the bottom of the assembly. The potentiometer and the gears must be lined up correctly so the seat will work right. Turn the small gear until its set screw on the potentiometer shaft is directly below the center terminal on the potentiometer.
  • Turn the seat so that when you install the large half gear, the flat edge of the large half gear is opposite the small gear and is parallel to the sides of the assembly. Put the gear on tightly. Nv Ss Lift the assembly into the simulator. Push it forward and back to ease it into position, under the floor. Be careful not to damage the gears and the potentiometer.
  • Install all the screws and nuts that hold the seat assembly in the simulator.
  • Reinstall the coin box and re-connect the harness.
  • Put the shifter back in the simulator. Put the locknuts on the tamperproof screws and the carriage bolts. Re-connect the harness.
  • Put the shifter gate back on, with the latch and the spring facing down. Then put the boot with the foam and boot cover plate on. Install the four tamperproof screws in the cover plate. Install the knob.
  • Re-install the floor. Put in the screws in the front of the floor and the screws in the metal floor trim.
  • Turn the mounting box until the seat mounting platform is square with the mounting box and parallel to the sides of the simulator. If it is not, then rotate the pivot arm until it is. When everything is square, tighten the nut on the right rod end against the pivot arm. Check this alignment again to make sure the mounting box is parallel to the front of the simulator and the seat mounting platform is square with the box.
  • Install the end plates of the mounting box with the tamperproof screws. Put the bottom cover back on.
  • Enter the self-test, go to the Set Controls screens, and re-initialize all the controls.
NOTE You must go through the Set Controls screen in the self-test because the seat assembly has been repaired. If you do not do this, the seat will not function correctly.

Replacing the Gears on the Seat Assembly

If the seat is not turning easily or at all, do the following:

  • Check for obstructions on the simulator floor and on the magnet plate below the floor. (You will have to pry up the floor to do this. Follow steps 1 and 2 in Replacing the Main Seat Bearing for information about doing this.)
  • Check the rod end bearings to make sure they are turning.
  • Check for broken or missing gears. Lift up the simulator or turn it on its side, with the seat high, and look through the hole in the bottom of the simulator at the gears.
WARNING This simulator weighs 750 pounds. Be extremely careful when you lift it, turn it, or work on it so that it does not fall.

In the hole directly underneath the main seat shaft, you can see two gears. The small gear is mounted on the potentiometer. The large gear is mounted on the bottom of the main shaft. If the gears are broken, cracked, or missing, you must replace them. You do not need to oil the bearings.

Replacing the Small Gear

Remove socket-head screws which hold the potentiometer bracket in the simulator and bring the potentiometer bracket and the small gear out of the simulator. See Figure 3-15.

  • Loosen the small set screw on the small gear hub. Use a 5/64-inch Allen wrench. Pull off the gear.
  • To put the new new gear on, first put the potentiometer back on the bracket, if you have removed it. 4, Install the bracket back in the game. Make sure the socket-head screws on the bracket are tight so it will not fall off. uw Turn the potentiometer until the flat of the potentiometer shaft is directly below the center terminal.
  • Turn the seat so that the flat edge of the large half gear is opposite the potentiometer and is parallel to the sides of the simulator.
  • Put the new gear on the potentiometer shaft. Do not turn the shaft while you are putting the gear on, Put Loktite on the set screw. Tighten the set screw.
Page 69

‘Hard Drivin’ Maintenance

Seat Is rotated for lllus- ‘Not Shown: 046404-01 tration purposes. A046334-01 Seat Flex Harness Assy 175012-0155 2-lnch Washer 046371-01 Tube (above the 1.5-inch bearing under the seat mounting platform) ‘A046399-01 Seat Harness 06077-001 hand 046359-01 ta Togs Nat Seat Mounting Platform 75-0702 41/4 Fender 178100-006 Washer, 1:5Inch Bearing (2 Places) 72-5528 rtepcek aor 172020-2428 Pivot Block ——_94g957-01 475Inch ‘Seat Mounting Box 176025-4106 Spring Pin Tamperproot Screw 177010-246_ 5/16 Locknut 17217-4616 Screw

178100-007 75-0438 Split Lock Washer 2-Inch Bearing (2 Places) 75-0195 Flat Washer 72-5912 Screw he veel Mounting Box End Plate

177010-246 5/16 Locknut 75-0158. Flat Washer 172017-4616 Screw 177010-244 #1/4 Locknut

046372-01 Seat Shield ‘75-010F #10 Washer 75-015F #1/4 Washer 176025-4108 Tamperproof Screw 75-055B 1/4 Interlock Washer 17024-0144 Low-Crown Nut ut 172021-006 3/8-Inch Rod End 177000-149 3/6 Hex Nut

046366-01 Seat Pivot Arm

046364-01 Bottom Cover Hard Drivin’ Saat Assembly

972021-106 Left Rod End

41908-1001 ie 176025-4106 5 KO Pot 75-5520B | ‘Tamperproof Screw 046365-01 1/4 Carriage Bolt . Screw Pot Bracket o4sase ‘i z 75-0408 ~~ eat Ass 75455288 Frame t Washer 178101-007 Carriage Bolt 046958-01 172020-—_24-Toothi Gear Magnet Arm 2436 04636201 Magnet Bracket 2.25-Inch 046489-01 Magnet Spring Pin 72-1828F #8 Screw 046361-01 Magnet Pivot Brkt 75-0188 #8 Washer 172017-4628 Shidr Screw 477010-238 #6 Locknut 477010-246 Nut 046367-01 fer aera Modified 75.0408 Split Washer 72-8008 Socket Screw lecied Gear AS eho Water

Figure 3-15 Maintaining the Seat Assembly

3-33

Page 70

Maintenance

  • Put the simulator back on the floor.
  • Go into the self-test and perform the Set Controls screens so the seat will operate properly.
NOTE You must go through the Set Controls screen in the self-test. If you do not do this, the seat will not function correctly.

Replacing the Large Gear

Rotate the seat so it will not move.

  • Remove the two socket-head screws holding the large gear on the main shaft. Take off the gear.
  • Install the new gear. Make sure that is meshes with the small gear. Tighten the socket-head screws well so the gear will not fall off. 4, If the seat did not turn or move while you were replacing this gear, you are done. If the seat did move, do the following: a.Take out the potentiometer bracket. Turn the gear until its set screw is directly below the center terminal on the potentiometer. b.Turn the seat so that the flat edge of the large half gear is parallel to the front of the simulator and is opposite to the place where the potentiometer bracket is installed. c, Install the potentiometer bracket back in the simulator. Make sure the gears do not turn from the position they are set in. Tighten the socket-head screws on the bracket. d.Put the simulator back on the floor. vw Go into the self-test and perform the Set Controls screens so the seat will operate properly.

Replacing the Magnet on the Seat Assembly

Before you replace the magnet because the seat is not locking, go through the flowchart in Figure 3-13 to determine the source of the problem. If your problem persists, check to see if the magnet has the correct resistance. If the magnet is working, you should measure 2 Q resistance across it.

  • Remove the floor trim, which is the strip of metal across the middle of the floor. Take out the Phillips-head screws on the back of the trim,
  • Remove the three Phillips-head screws along the front of the simulator under the rubber floor mat. Turn the seat out of the simulator as far as it will go. Pry up the floor.

3-34

  • Turn the seat so you can see the magnet. The magnet is attached to the arm by a bracket that permits the magnet to move very freely. Before replacing the magnet, check to see that the harness to the magnet is properly connected, since that could be a cause of magnet failure. 4, If the magnet must be replaced, unscrew the two Phillips-head screws that hold the magnet on the magnet bracket and disconnect the harness. Discard all the hardware that came with the new magnet and install the magnet with the Phillipshead screws and nuts. Re-connect the harness. wa
  • Re-install the floor. Insert the screws that hold the floor and the metal floor trim in the simulator.

Replacing the Seat

Potentiometer

Before you replace the seat potentiometer, go through the Set Controls screens in the self-test. If this doesn’t fix the problem, do the following: ¢ If your problem is with erratic operation, then follow the flowchart in Figure 3-7.

  • If the seat is not locking when it should, follow the flowchart in Figure 3-13. If the seat is locking when it should not, follow the flowchart in Figure 3-14. If the seat potentiometer is not working properly and you cannot repair it immediately, go to the screen Disable Broken Controls in the self-test. Disable the seat potentiometer circuit so you can continue to operate the simulator. This is only a temporary measure . You should repair the seat potentiometer as soon as possible. The potentiometer is mounted next to the end of the main shaft on the seat. The potentiometer has soldered. connections, so you will need a soldering gun. The seat is shown in Figure 3-15. To work on the gears, turn the simulator on its side or securely prop up the front of the simulator. In either case, you will need help, since the simulator is very heavy. You may find it easier to work on the simulator by turning it on its side, with the corner with the seat bearings high.
WARNING This simulator weighs 750 pounds. Be extremely careful when you lift it, turn it, or work on it so that it does not fall.
  • In the hole directly underneath the main seat shaft, you can see two gears. The small gear is mounted
Page 71

on the potentiometer, which is on the potentiometer bracket. Remove the socket-head screws that hold the potentiometer bracket in the simulator and bring the potentiometer bracket out of the simulator.

  • Loosen the set screw on the small gear hub. Use a 5/64-inch Allen wrench,
  • Loosen the locknut on the potentiometer shaft and take the potentiometer out of the bracket. Take off the harness wires. Leave the ground wire attached to the bracket. 4, Put the new potentiometer in the bracket, making sure you put the key in the hole in the bracket. The connectors should be on the same side as the ground wire bracket. Tighten the nut on the shaft.
  • Bend the potentiometer connectors up, but not so they touch the bracket. Solder on the wires in the following order: black nearest the ground wire, yellow in the middle, and red on the other side.
  • To put the new gear on, first put the potentiometer on the bracket, if you have removed it.
  • Install the bracket back in the game. Make sure the socket-head screws on the bracket are tight so it will not fall off.
  • Turn the potentiometer until the flat of the potentiometer shaft is directly below the center terminal.
  • Turn the seat so that the flat edge of the large half gear is opposite the potentiometer and is parallel to the sides of the simulator.
  • Put the new gear on the potentiometer shaft. Do not turn the shaft while you are putting the gear on. Put Loktite on the set screw. Tighten the set screw.
  • Put the simulator back on the floor.
  • Go into the self-test and perform the Set Controls screens so the seat will operate properly.
NOTE You must go through the Set Controls screen in the self-test. If you do not do this, the seat will not function correctly. Maintenance

Video Display

If you are having problems with the video display, check the suggestions in Table 3-11, Troubleshooting the Video Display, before you remove the display.

Removing the Video Display

Perform the following procedure to remove the video display. (See Figure 3-16.)

  • Turn the simulator power off and wait two minutes. Leave the power cord plugged in.
WARNING High Voltage The video display contains lethal high voltages. To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation The video display has been designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube may implode if struck or dropped. Shattered glass may cause injury within a 6-foot radius. Use care when handling the display.
  • While you are waiting, remove the six screws that hold the small top service panel on the simulator.
  • Disconnect the simulator harness to the attraction sign. Remove the larger outside panel attached to the attraction sign by taking off the carriage bolts that hold the panel on the simulator.
  • Discharge the high voltage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: Table 3-11 Troubleshooting the Video Display

3-35

Page 72

Maintenance

Video

Replacing the Video Display

1/4-20 Carriage Bolt Washer Nut

1/4-20 Screw

1/4-20 Hex-Head Screw Washer Lock Washer

Motor Amplifier Assembly

Figure 3-16 Removing the Video Display a. Attach one end of a solid 18-gauge wire to a well-insulated screwdriver or wooden handle. b.Attach the other. end of the wire to an earth ground. c. Quickly touch the blade end of the screwdriver to the CRT anode by sliding it under the anode cap. d. Wait two minutes and repeat part c. . Disconnect the video display harness connectors from the display. ww

  • Remove the motor amplifier PCB and heat sink assembly from the cabinet side.
  • Remove the four screws and washers that hold the video display on the shelf.
  • Pull the video display out of the back of the cabinet.

3-36

WARNING When you take the video display out of the cabinet, do not drop it! To make the removal easier, we recommend that two people work together to re move the display. You should wear gloves to protect your hands from the sheet-metal edges.
  • Replace the video display as described in the following procedure.

Perform the following procedure to replace the video display in the cabinet. (See Figure 3-16.)

Page 73
  • Carefully lift the video display onto the display shelf in the cabinet.
NOTE When you replace the cathode-ray tube and yoke as a single unit, adjust the brightness, size, and centering as described in the display manual. Check the purity and convergence according to the display manual instructions, but adjust both only if required.
  • Position the display so that the four holes in the video display mounting brackets line up with the four holes in the video display shelf.
  • Loosely install the four hex-head screws and washers through the mounting brackets and into the video display shelf.
  • Push the video display forward against the bezel. Tighten the screws. Be sure that the display is centered horizontally in the bezel.
  • Install the motor amplifier PCB and heatsink on the cabinet side.
  • Connect the display harnesses to the display.
  • Replace the large and small top service panels.

Motor Amplifier Assembly Removing the Motor Amplifier Assembly

  • Turn the simulator power off and wait two minutes. Leave the power cord plugged in.
WARNING The PCBs in ihis assembly contain lethal high voltages. To avoid injury, do not attempt to service this display until you observe all precautions necessary for working on high-voltage equipment.
  • Unplug the power cord.
  • Take off the harness to the boards. 4, Remove the entire assembly from the cabinet. Do not remove the PCBs from the heat sink. Ww Send the entire assembly back to Atari Games Customer Service for trade-in. Maintenance

Static-Sensitive Devices

Devices

Replacing Static-Sensitive

Be careful when you are working with static-sensitive devices on the simulator PCBs. These can be microprocessors, field-effect transistors (FET), complementary metal-oxide semiconductors (CMOS), and other large-scale integration (LSI) devices that use metal-oxide semiconductor (MOS) technology. Static charge that has built up in your body can cause a static-sensitive device to fail. Leakage from an improperly grounded soldering iron can also cause a static-sensitive device to fail. Before you handle a static-sensitive device or a PCB with such devices attached to it, ground any static voltage that may have accumulated in your body by touching an object that has been earth grounded When you solder a static-sensitive device, use a soldering iron with a properly grounded three-wire cord. Before you replace a static-sensitive device, make sure it is actually defective. A static-sensitive device can appear defective due to leakage on a PCB. To make sure a device is defective, ground any static voltages as described in the paragraph above. Clean both sides of the PCB with flux remover or an eraser. For discrete FETs, clean thoroughly between the gate, drain, and source leads. Then test the device. If you are replacing a static sensitive device, new static-sensitive devices may be packaged in conductive foam or may have a protective shorting wire attached to the pins. Remove the conductive foam just prior to inserting the device into its socket or soldering it to a PCB. Remove the shorting wire only after the device is inserted into its socket or after all the leads are soldered in place.

Speakers

If you are having problems with a speaker, check the suggestions in Table 3-12, Troubleshooting the Speakers, before you replace it.

Removing a Speaker

  • Turn the simulator power off,
  • Remove the dashboard, following the directions in the section Removing the Dashboard.

3-37

Page 74

Maintenance

CAUTION Be careful when handling the speaker. The cone material is fragile and can be easily damaged.
  • Remove and replace the speaker.
  • Install the dashboard, following the directions in the section Installing the Dashboard.

Cleaning the Coin

Mechanism

Use a soft-bristled brush to remove loose dust or foreign material from the coin mechanism. A toothbrush can be used to remove any stubborn build-up of residue in the coin path. After cleaning the coin mechanism, blow out all of the dust with compressed air.

Cleaning the Interior Components

Perform the following procedure to clean the components inside the cabinet.

  • Open the small top service panel and bottom service door.
WARNING Turn off the simulator power, but do not unplug the power cord before cleaning inside the cabinet. The power cord pro vides a ground path for stray static voltages that can be present on the cleaning tools.

Table 3-12 Troubleshooting the Speakers . Discharge the high voltage from the cathode-ray tube (CRT) before proceeding. The display assembly contains a circuit for discharging the high voltage to ground when power is removed, However, to make certain, always discharge the display as follows: a. Attach one end of a solid gauge wire to a wellinsulated screwdriver or wooden handle. b.Attach the other end of the wire to an earth ground. c. Quickly touch the blade end of the screwdriver to the CRT anode by sliding it under the anode cap. d. Wait two minutes and repeat part c. . Use a vacuum cleaner with a soft long-bristled brush attachment or use a soft-bristled paint brush to remove loose dirt and dust accumulated on the inside of the cabinet. Be sure to clean the electrical components thoroughly (power supply, PCB assemblies, video display, etc.).

CAUTION Be extremely careful when cleaning the electrical components inside the cabinet. Avoid touching the electrical components with any solid object other than the soft bristles of the vacuum attachment or paint brush.

3-38

Page 75

Chapter 4

Illustrated Parts Lists

This chapter provides information you need to order parts for your game. The parts lists (except for the PCB parts lists) are arranged alphanumerically by Atari part number. All Aprefix numbers, which are assemblies, come first. Next are part numbers with six numbers followed by a hyphen (000598- through 201000-). Ending the list are part numbers with a two-number designation followed by a hyphen (00- through 99-). The PCB parts lists are arranged in alphabetical order by component. Within each section the parts are arranged numerically by part number. ‘When you order parts, give the part number, part name, the number of this manual, and the serial number of your game. With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games. Atari Games Customer Service phone numbers are listed on the inside front cover of this manual.

Page 76

Ilustrated Parts Lists

a‘A046486-01045951-01 Center
-4046300-01Shifter AssyCanopy
‘Attraction Sign Sub-Assy(See Figure 4-6)177010-440 #10

046304-01 Locknut Atracion Decal 178254-016 Foam 046307-( Tape

Attraction aafl75-0108 #10 Washer
‘046309-0175-010F #10 Washer
Aoasa5a-o1 —_Alraction CoverAttraction|176020-220 #8
AttractionFluorescent LintFrame2 |Phillips Hd Screw
Assemblyescent Lighti82-8110B #10 Sckt-
Lamp Fixturety[Hd Screw
178232-001045949-01Poyhot-
Lamp Retaining iAt. Canopyani |046296-01

it

#10 Washerogsaor-or=}Hit|Fint Ganopy Support
75-99511Top Lit|i
#10 NuvWasher AssyDecalport#10 Carriage Bolt
82-8108rdroalTe O15F
#10-24 Black Screwrorya1A Wehr
arod75-055B
eeprod]44 Intorlock Wehr
1/4 Button-Headwet |Salad
Screw\!Sq Finish Plug
75-015|17024-0144
1/4 Washer|1/4 Black Nut

i

045950-01 | Left Canopy 046409-02 Rt. Inner Decal

a(fict~75-015F
=iy> So1/4 Washer
046405-01.AHsty176025-3620
Bottom Left:CNELAPS etarperpcoot
Decalel|CnSeen
2!|046294-01SN
‘al=-rWhFloor Trim~ el

58 ame) EF iT

75-5520Be-foakhos
Carriage Bolt~#2.tl~~
75-0558—_—2:~~
1/4 InterlockISS“~~
Washer|—
|75-5520aT~ a
1/4 Carriage.~~~
\Bolt|.aa
Cabinet|~anice
Firewallhfe=|NAS~>
SfswOS~AwLUe
IPeso046410-01 © ><ALrN
75-07002046415-011/4 Carriageeens FateSNPS
1/4 Fendervelole Cover 75.5508Bolt046278-01EONOe
WasherF]Plate1/4Front Floor ~Z~
47012-4111CarriagePane”— | n046340-01~
Spring NutBolt2Comp Bracket Assy

177010-244 A046341-01

1/4 NutiCoin Counter

119006-103

A046380-01e=10 KQ Pot
Clutch & Brakea7160094-241
Pedal Assy2Slide Switch
(See Figure 4-7)~~046255-01160052-001
<Coin BoxPush-Button Switch

7 Cabinet Shroud 75-5540 1/4 Carriage Bolt

046316-01Zz6:8091-01

Under-Dash ‘A046253-01 Coin Box Assy \ Cash Box

046390401"CovereaeViecor477000-144 Nut
Bumper Pad477000-144 1/4 Nut75-5520B Carriage Bolt171027-001
176020-212176020-21247949-4411 Spring Nut'75-07002 Fender WasherCoin Door
#8 Phillips-+#8 Phillips-pring75-0458 Lock Washer

Hd Screw Hd Screw Figure 4-1 Cabinet-Mounted Assemblies, Front View A046250-01 B

Page 77

Illustrated Parts Lists

176025-3620 1/4 Tamperproot ‘A046252-01 Screw Control Panel Assy —_75-015F (See Figure 4-3) 1/4 Washer

176020-212 #8 Phillips-Head Screw A046355-01 Seat Assy (See Figure 4-2)

177024-0144 i ihcanage 4 Black Nut ! Bolt

\ 72-5520 \ 1/4 Hex Hd Screw ! 75-0458 1/4 Lock Wshr 75-015F 75-0158 t 1/4 Washer 4/4 Wsbr 75-0553 1/4 Interlock Washer I 17024-0144 1 ; 4 Black Nut

75-0158 1/4 Washer 177010-244 1/4 Locknut

4046403-01 \ Gas Pedal Assy (See Figure 4-8)

176020-212 #8 Phillips-Head Screw Not Shown: A043705-01 Fan Cord Assy A046338-01 Attraction Harness Assy ‘A046321-01 Main Harness Assy ‘A046322-01 Power Hamess Assy 046323-01 ‘AC Harness Assy ‘A046324-01 Video Harness Assy ‘A046325-01 Motor Interconnect Harness Assy A046326-01 PCB Interconnect Harness Assy 046335-01 Shifter Ribbon Cable Assy A046336-01 Motor Ribbon Cable Assy A046337-01 PCB Ribbon Cable Assy A039254-01 ‘Component Bracket Harness Assy 046401-02 Top Rt. Decal 046409-01 Lft. Inner Decal 148007-104 Speaker 178126-002 ‘Tamperproot Hex Key Driver

75-015F 1/4 Black Washer 82-8532B 1/4 Button-Hd Screw (holding attraction frame to attraction ssign sub-assy)

Figure 4-1 Cabinet-Mounted Assemblies, Front View, Continued. A046250-01 B

Page 78

Illustrated Parts Lists Hard Drivin’

75-0105 | — 139019-001

046402-01#10 Washer‘75-5540B
Video Display7B 010E | Vite0 Display1/4 Carriage Bolt
Bezel#10 Washer75-0158
75-0108178056-00282-8110B1/4 Washer
#10 WasherFoam Tape#10 Screw177000-144
82-8168046299-0175.01sF]_177010-4401/4 Nut
#10 Socket-Hd ScrewDisplay1/4Washer|#10 Locknut
178263-0402ae82-8116B)046297-01(large Topje Washor— 097332-01
Foam Tape'etainer#10 Socket-HdCenterService PanelLouvered
Screw]CanopyGaile

178263-0402) Retainer

Foam Tape|/ae
f|046284-01

| ‘Small Top

~|Service

1 Panel

‘

i

/gNNl
/.™.

/ 176020-220

.~y#8 Phillips-Hd
-~Screw
/o.Sy

l 75-0458 1/4 Lk Washer | 72-5520 1/4 Hex Hd Screw

2275-0158 1/4 Washer

oS i

046313-01||
Video DisplayC—;

Shield if

ERS|176015-110
3SbaScrew
a9_:
8oe.—~A045195-01
.aS-..Motor Amp
|_.B|Assy
|8:;
178255-001.Pan
Gideeo»4044431-01
.>3|APU PCB Assy

72-5532 (See Figure 4-12) Caster | bass05-02 ‘A046345-01

Bottom Rt,|Power Supply Assy
Decal®|(See Figure 4-10)
7°Ne|A043910-01

SON] On ft Hamess Assy ° ‘A045988-01 Main PCB Assy

aeAPN 8820"(See Figure 4-11)171002-001
Brake PCB Assyniespeend.ae
(See Figure 4-14)Figuie 41a)ADSP PCB Assy178093-001
°478120-606_A04546491-01Fan Blade Guard
17603-1610POB StandottSound PCB Assy
046280-01#6 Phillips-176039-1610 #6
Bottom ServiceHead ScrewPhilips Head Screw

Poor Fiber Washer 175004-708 Fiber Washer

Figure 4-1 Cabinet-Mounted Assemblies, Rear View A046250-01 B

4-4

Page 79

Cabinet-Mounted Assemblies Illustrated Parts Lists

Parts List

Part No.DescriptionPart No.Description
A043705-0112-Inch Fan Cord Assembly045949-01Right Canopy
A043916-01On/Off Harness Assembly045950-01Left Canopy
A043932-01Shifter PCB Assembly (See Figure 4-13)045951-01Center Canopy
A044431-01APU PCB Assembly (mounted on Power046255-01Coin Box Shroud
Supply Assembly) (See Figure 4-12)046278-01Front Floor Panel
A044817-01Brake PCB Assembly (mounted on Clutch046280-01Bottom Service Door
and Brake Assembly) (See Figure 4-14)046281-01Large Top Service Panel
A045195-01Motor Amplifier Assembly046284-01Small Top Service Panel
A045988-01Hard Drivin’ Main PCB Assembly (See046294-01Floor Trim

Figure 4-11)

A045989-01ADSP PCB Assembly046296-01Front Canopy Support

046297-01 Center Canopy Retainer

A046252-01Control Panel Assembly (See Figure 4-3)046299-01Display Shield Retainer
2:Coin Box Assembly046309-01Attraction Frame

A046254-01 Attraction Assembly. Replaceable Parts:

A046300-01Attraction Sign Sub-Assembly046313-01Monitor Shield
A046338-01Attraction Harness Assembly046316-01Under-Dash Cover
046304-01Attraction Decal046390-01Bumper Pad
046307-01Attraction Shield046401-01Top Left Decal
046308-01Attraction Cover046401-02Top Right Decal
170003-00118-Inch, 15 Watt Fluorescent Light046402-01Video Display Bezel
171086-00118-Inch Fluorescent Lamp Fixture046405-01Bottom Left Decal
178232-001Fluorescent Lamp Retaining Clip046405-02Bottom Right Decal
75-0108,#10 Washer046409-01Left Inner Decal
75-99511#10 Nut/Washer Assembly046409-02Right Inner Decal
82-8108B#10-24 x 1/2-Inch Black Screw046410-01Number Plate Decal

046415-01 Hole Cover Plate A046256-01 Cabinet

A046321-01Main Harness Assembly139019-00125-Inch Framed Color Raster, Medium
A046322-01Power Harness AssemblyResolution Video Display
A046323-01AC Harness Assembly148007-1044 1/2-Inch Diameter, 8Q, 10W Shielded

Speaker

A046324-01Video Harness Assembly171002-001Exhaust Fan
A046325-01Motor Interconnect Harness Assembly171027-001Coin Door (See Figure 4-9)

A046326-01 PCB Interconnect Harness Assembly

A046335-01Ribbon Cable Assembly to the Shifter175004-706.154 LD., .375 O.D. Fiber Washer

175004-708, 190 LD., .640 O.D. Fiber Washer

A046336-01Ribbon Cable Assembly to the Motor176020-208#8 x 1/2-Inch Black Phillips-Head Screw
A046337-01Ribbon Cable Assembly to the PCBs176020-212#8 x 3/4-Inch Black Phillips-Head Screw

A046340-01 Component Bracket Assembly

A039254-01Component Bracket Harness176020-220#8 x 1 1/4-Inch Black Phillips-Head Screw
Assembly176025-36201/4 Black Tamperproof Screw
A046341-01Coin Counter Assembly176033-1610#6 x 5/8-Inch Phillips-Head Screw
119006-10310 KQ Potentiometer Audio Taper177000-1441/4 Hex Nut

160034-241 Slide Switch

160052-001Push-Button Switch177010-2441/4-20 Polymer Locknut

177010-440 #10-24 Polymer Locknut

A046345-01Power Supply Assembly (See Figure 4-10)177012-111Push On Spring Nut
A046355-01Seat Assembly (See Figure 4-2)177024-01441/4-20 Low Crown Black Nut

A046380-01 Clutch And Brake Pedal Assembly (See

Figure 4-7)178056-0021/2-Inch Wide Foam Tape
A046403-01Gas Pedal Assembly (See Figure 4-8)178093-001Fan Blade Guard

178120-606 PCB Standoff

A046486-01Shifter Assembly (See Figure 6-6)178126-002Tamperproof Hex Key Driver

A046491-01 Sound PCB Assembly

038091-01Cash Box178254-016Double-Coated Acrylic Foam Tape
Page 80

Iustrated Parts Lists

Cabinet-Mounted Assemblies Parts List

Part No.DescriptionPart No.Description
178255-001Adjustable Swivel Glide75-5528B1/4-20 x 1 1/2-Inch Round Head, Square
178257-004Black Square Finish PlugNeck Black Carriage Bolt
178263-04021/4-Inch Wide Foam Tape75-5540B1/4-20 x 2 1/2-Inch Black Carriage Bolt
178263-06043/8-Inch Wide Foam Tape75-070021/4 Fender Washer
72-5116#10-24 Hex Head Screw75-99516#6-32 Nut/Washer Assembly
1/4-20 x 1 1/4 Hex Head Screw75-9518#8-32 Nut/Washer Assembly
4 1/2-Inch Swivel Caster82-8110B#10-24 x 5/8-Inch Black Hex Socket

1/4 x 3/4 Inch Hex Head Screw Button-Head Screw

#10 Flat Black Washer82-8116B#10-24 x 1-Inch Black Hex Socket Button-

Head Screw

75-0108#10 Flat Washer82-8532B1/4-20 x 2-Inch Black Button-Head Screw

75-O15F 1/4 Steel Flat Black Washer 75-0158 1/4 Flat Washer Documentation for the Hard Drivin' game:

75-0408#10 Steel Split-Lock WasherSP-327Hard Drivin’ Schematic Package

is ST-327 Hard Drivin’ Self-Test Label

75-04581/4 Steel Split-Lock WasherTM-295Wells-Gardner 25-Inch, Med Res, Color

1/4 Steel Black Oxide Interlock Washer Display Service Manual (for Model #10-24 x 1 3/4-Inch Black Carriage Bolt 25K5515)

75-5520B1/4-20 x 1 1/4-Inch Round Head, Square*TM-327Hard Drivin' Operator's Manual

Neck Black Carriage Bolt

Page 81

Hard Drivin’ Tilustrated Parts Lists

N O T E S

Page 82

Itlustrated Parts Lists.

Not Shown: A046334-01 ‘Seat Flex Harness Assy 046404-01 175012-0155 Seat 2-Inch O.D. Washer 046371-01 7 ; Tube (between pivot block and up- ae per bearing in seat mounting box) Purposes. 1046 333-01 Seat Harness 108007-001 Loktite

046359-01 177023-001

4/4 Toggle Nut178100-006Seat Mounting Platform

7507002 1.25-In. |. 1/4 Fender Beating (2 4

weetPlanes)046360-01
‘Screw172020-2428Pivot Block046357-01

1.75-Inch Seat Mounting Box 176025-4106 Spring Pin ‘Tamperproot Serew 177010-246 5/16 Locknut 17217-4616 Shoulder Screw

8100-007 75-0438. Spt Lock Washer 1 5/8 1.D. Bearing (2 Places)

Vii Box End Plate 72-5520 Screw 177010-246 5/16 Locknut 75-0158 Flat Washer bated 172017-4616 Shoulder Screw 177010-244 #1/4 Locknut chet 75.0188, Flat 046372-01 Seat Shield Washer 7S-010F #10 Washer 75015F #1/4 Washer 76025-4108 Tamperproo! Screw 75-055B 1/4 Interlock Washer 17024-0144 Low-Crown Nut . 172021-006 Rt. Rod End 4177000-149 Lock Nut

Fy 046366-01 5 Seat Pivot Arm : . as 046364-01 33 Bottom Cover Fs { 3 j Be Ke ! 172021-106 4 Left Rod End

11908-1001 176025-4106 5KQ Pot

75-55208Tamperproot Screw72-8008046365-01
4/4 Carriage BoltScrewPot Bracket

046356-01 75-0408 Seat Ass} Washer 75-55288 frame / 178101-007

Carriage Bolt04695801172020-24-Tooth Gear

Magnet Arm 2436 046362-01 Magnet Bracket 2.25-Inch 046373-01 Magnet Spring Pin 72-1828F #8 Screw 046361-01 Magnet Pivot Brit / ] 75-0188 _#8 Washer 172017-4628 Shidr Screw 477010-238 #8 Locknut 177010-246 Nut 046967-01 72-8008 Screw Modified Gear 75-0408 Split Washer

4-8 ‘75-0108 #10 Washer

Figure 4-2 Seat Assembly A046355-01 A

Page 83

Illustrated Parts Lists

Seat Assembly Parts List

Part No.DescriptionPart No.Description
A046333-01Seat Harness Assembly176025-4106#10-32 x 3/8-Inch Tamperproof Screw
A046334-01Seat Flex Harness Assembly176025-4108#10-32 x 1/2-Inch Tamperproof Screw
046356-01Metal Seat Frame177000-1493/8-24 Hex Nut
046357-01Seat Mounting Box177010-238#8-32 Polymer Locknut
046358-01Magnet Arm177010-244#1/4-20 Polymer Locknut
046359-01Seat Mounting Platform177010-2465/16-18 Polymer Lock Nut
046360-01Seat Pivot177023-0011/4-20 Toggle Nut
046361-01Magnet Pivot Bracket17024-0144Low-Crown Nut
946362-01Magnet Bracket178100-00715/8-Inch LD, Bronze Bearing
046363-01Mounting Box End Plate178100-0061.25-Inch ID, Bronze Bearing
046364-01Bottom Cover for Mounting Box178101-00724-Tooth Spur Gear
046365-01Potentiometer Bracket72-1828F#8-32 x 1 3/4-Inch Phillips-Head Screw
046366-01Seat Pivot Arm#1/4-20 x 1-Inch Hex-Head Screw
046367-01Modified Gear#1/4-20 x 1 3/4-Inch Hex-Head Screw
046371-01Tube1/4-20 x 1 1/4-Inch Hex-Head Screw
046372-01Seat Shield5/16-18 x 3/4-Inch Hex-Head Screw
046404-01Seat72-8008#10-32 x 1/2-Inch Socket-Head Screw
046373-01Magnet75-010F#10 Flat Black Washer
106007-001Loktite 29075-0108#10 Flat Washer
119008-10015 KQ Potentiometer75-015F#1/4 Flat Black Steel Washer
172017-46165/16-18 x 1-Inch Long Shoulder Socket-75-0158#1/4 Flat Washer

Head Screw 75-0185 #8 Flat Washer

172017-46285/16-18 x 1.75-Inch Long Shoulder Socket75-01985/16 Flat Steel Washer
Head Screw75-0408#10 Split Lock Washer
172020-2428.375-Inch Diameter x 1.75-Inch Slotted75-04385/16 Steel Split-Lock Washer

Spring Pin

172020-2436.375-Inch Diameter x 2.25-Inch Slotted75-04581/4 Steel Split-Lock Washer
Spring Pin75-055B1/4 Interlock Washer
172021-0063/8-Inch Diameter, 3/8-24 Rod End75-5520B1/4-20 x 1 1/4-Inch Round Head, Square

Neck Black Carriage Bolt

172021-1063/8-Inch Diameter, 3/8-24 Rod End—Left75-5528B1/4-20 x 1 1/2-Inch Round Head, Square

Hand Thread Neck Black Carriage Bolt

175012-0155,2,0-Inch O.D, Washer75-070021/4 Fender Washer
Page 84

Illustrated Parts List Hard Drivin’

GLreLz 82-8912B Black Screw 176025-3620 Not Shown: 75-011F 3/8 Washer 1/4-20 Tamper- A046327-01 75-0518 9/8 Interlock Washer proof Screw75- Key Switch Harness Assy (4 places) O1SF 177010-240 4/4 Washer #10-24 Locknut

A046460-01 Steering Assy 046445-01 (See Figure 5-5) Key Switch Assy (See Figure 5-4) 176020-212 #8 Phillips- Head Screw

7551128 e < +#10-24 Car- 75-56208 ; Carr. Bolt riage Bot 1700-144 veosse. 17024-0144 1/4 Interlock 114-20 Nut Washer 75-07002 75-055B 14 Fender Lock Vasher Washer q77012-411 Push-On Spring Nut 046408-01 ‘75-5520 Ctrl Panel Carriage Bolt Decal

460052-001 :

036895-01Pushbutton\oa64

witch Bezel Switch 59-01

seek"178233-002ogeas7 OtSteering Wheel
“Seat Adjust”a9q¢a28-01vateerng,|Center Decal
Button W/ — ysh-Button046295-0175-0455
LampHamessControl1/4 Lock
160044-001AssyPanelWasher

Snap-Action 75-8512 Sairp Socket-Head Serew

178099-005 Steering Wheel

Figure 4-3 Dashboard Assembly A046252-01 A

4-10

Page 85

Mlustrated Parts List

Dashboard Assembly Parts List

Part No.DescriptionPart No.Description
A046327-01Key Switch Harness Assembly177024-01441/4-20 Low Crown Nut
A046328-01Push Button Harness Assembly178233-0026.3 V “Seat Adjust” Button With Lamp As-
A046445-01Key Switch Assemblysembly
A046460-01Steering Assembly72-85121/4-20 x 3/4-Inch Socket-Head Screw

75-O11F 3/8 Flat Black Washer 036895-01 Push Button Switch Bezel

046295-01Control Panel75-015F1/4 Flat Steel Washer
046408-01Conwol Panel Decal75-0458,1/4 Split-Lock Washer
160044-0015V/5mA SPDT Snap-Action Switch75-051B3/8 Black Interlock Washer

75-055B 1/4 Interlock Washer Red, Lighted, SPDT Pushbutton Switch

176020-2128 x 3/4-Inch Phillips-Head Screw75-5108B#10-24 x 1/2-Inch Black Carriage Bolt
176025-36201/4-20 x 1 1/4-Inch Black Tamperproof75-5112B#10-24 x 5/8-Inch Carriage Bolt
Screw75-5520B1/4-20 x 1 1/4-Inch Black Carriage Bolt
177000-1441/4 Hex Nut75-070021/4 Fender Washer

82-8912B 3/8-16 x 3/4-Inch Black Button-Head

177010-240#10-24 Polymer LocknutScrew

177012-111 Push-On Spring Nut

4-11

Page 86

Ilustrated Parts List Hard Drivin’

Not Shown:

172020-0814 Spring Pin 72-8006 #10-32 Socket-Head Screw 75-0408 #10 Split-Lock Washer

046450-01 176008-110 Actuator #10-32 Socket- 78-0408 — Head Screw #10 Lock Washer

175009-364 Nylon Washer OheHe-01: Shaft

178256-001 178001-004 Torsion 11 ! 178001-004 Retaining Spring Retaining Ring

160045-003 ‘Switch

046446-01 Housing

72-1412 046447-01 A046327-01 +#4-40 Phillips- Collar Key Switch Head Screw ata Harness Assy 75-0148, #4 Washer 177010-232 #4-40 Nut

Figure 4-4 Key Switch Assembly A046445-01 B

4-12

Page 87

Hard Drivin’ Ilustrated Parts List

Key Switch Assembly Parts List

Part No.DescriptionPart No.Description
046446-01Housing177010-232#4-40 Nut
046447-01Collar175009-364Nylon Washer
046448-01Key178001-0041/2-Inch Retaining Ring
046449-01Shaft178256-001Torsion Spring
046450-01Actuator72-1412S#4-40 x 3/4-Inch Phillips-Head Screw
160045-003SPDT Switch72-8006#10-32 x 3/8-Inch Socket-Head Screw
172020-08140.125-Inch x 0.875-Inch Slotted Spring Pin75-0148#4 Flat Washer
176008-110#10-32 x 5/8-Inch Nyloc Socket-Head75-0408#10 Split-Lock Washer

Screw

4-13

Page 88

Illustrated Parts List Hard Drivin’

72-8816 7e-1709 #8-32 Hex- rease Head Screw 046378-01 | 046454-01 3/4-Inch asad 8512 da L oP 178026-015 wae Extension Spring TASS achor

75-0185 1/4 Flat Washer (1 Place) 046462-01 Rubber Stop 046463-01 Rubber Stop Brkt 178181-7806 Steel Spacer (4 places) 177010-260 3/4 Nut

A046332-01 Motor Assy 046457-01 A046331-01 Hu Steering Assy Hamess 175002-001 Flat Washer 119018-001 10-Turn Pot

175002-001 Washer 046456-01 72-8810 Pot Bracket —#8-32 Screw 177010-241

178099-005, Steering Wheel '178181-7806 Spacer

046455-01 Stop Bracket capes.

Hub Decal

177010-260 Locknut

Screw 046458-01 75-6458 Hub Cover Washer

Figure 4-5 Steering Assembly A046460-01 A

4-14

Page 89

Tljustrated Parts List

Steering Assembly Parts List

Part No.DescriptionPart No.Description
A046331-01Steering Assembly Harness177010-241#8-32 Nyloc Nut
A046332-01Motor Assembly177010-2603/4-16 Nyloc Nut
046378-013/4-Inch Spacer177011-2603/4-16 Thin Nyloc Nut
046454-013-Rotation Stop178026-0153/16-Inch O.D. x 1 3/8-Inch Extension

Spring 046455-01 Stop Bracket

046456-01Potentiometer Bracket178099-005,12-Inch Steering Wheel
046457-01Steering Wheel Hub178181-78063/8-Inch Long Steel Spacer
046458-01Hub Cover72-85121/4-20 x 3/4-Inch Hex-Head Screw

72-8806 #8-32 x 3/8-Inch Hex-Head Screw 046459-01 Steering Wheel Hub Decal

046462-01Rubber Stop72-8810#8-32 x 5/8-Inch Hex-Head Screw
046463-01Rubber Stop Bracket72-8816#8-32 x 1-Inch Hex-Head Screw
119018-00110-Turn Potentiometer75-01581/4 Flat Washer (for ground wire

75-0185 #8 Flat Washer 175002-001 0.750-Inch Flat Shaft Washer

176022-3806#8-32 x 3/8-Inch Thread Lock Hex-Head75-04581/4 Split-Lock Washer
Screw78-1709Grease

4-15

Page 90

Illustrated Parts List Hard Drivin’

046525-01 Detent Lever

4-16 Not Shown: 177000-132 17e026-017 #4 Hex Nut on Latch Spring "9 : 178006-004 Revers Poston Latch Spring Compression Sting

  • . 75-048S Reverse Position Latch Bearing elo Wether 4-40 Pan ead Serow on Latch 178026-017 cee Spring Latch Extension Spring

176025-4416 1/4-20 Button-

  • Head Screw 046523-01 baad Detent Roller
524-0172-1818Feinen

Roller Bearing #8 Pan-Hd Screw }oot Cover

177010-24175-0288Plate
opgest#8 Washer

#10 Flat Washer Rha ed ed #8-32 Locknut 046474-01 1/4 Washer bare

7 046560-01

F.046476-01Boot
detent Lover SpringShiter GateCushion

178192-6306 Spring Spacer 72-8012 75-5528B seen 114-20 Carriage Bolt soenag Washer 7010-244

#10 Flat Washer1iGr20 Lockrut046479-01
72-£00SLShifter Housing

#1092 Shoulder casazec, 106007-001 Reverse Position Loktite 290 Latch

‘A046329-01 19008-1001 Harness 046477-01 _-Potentiometer Assy Pitch Bar mS-85128 1/4 Carriage Bolt 177010-244 1/4-20 Lock Nut 171087-001 Strain Gauge

73-00824 Cotter Pin

046482-01 Roll Link 119008-1001 Potentiometer 046906-01 046481-01 Magnet Plate 72-6802 / Roll Bar Screw

72-E802

Pitch Link Loktite 290 72-8808 oatssoor s7600"138 Hinged Plate Hox Nut

177010-241 Locknut

046472-01 Bee 046484-01 Magnet

046483-01#10Screw—Detent PiateInsulator

Pivot Shaft Poo 046489-01 m 046485-01 Magnet

Magnet Bracket

Figure 4-6 Shifter Assembly A046486-01 A

Page 91

Hard Drivin’ Illustrated Parts List

Shifter Assembly Parts List

Part No.DescriptionPart No.Description
A046329-01Harness Assembly177000-132#4 Hex Nut
046424-01Reverse Position Latch177000-136#6-32 Hex Nut

046427-01 Knob

046440-01Reverse Position Latch Bearing177000-138#8-32 Hex Nut

177010-238 #8-32 Polymer Locknut

046472-01Magnet Insulator177010-241#10-32 Polymer Locknut
046474-01Boot177010-2441/4-20 Polymer Locknut

046475-01 Boot Cover Plate

046476-01Shifter Gate178006-004Compression Spring

178026-017 Reverse Position Latch Spring

046477-01Pitch Bar178026-019Detent Lever Spring
046478-01Pitch Link178192-6306Spring Spacer

046479-01 Shifter Housing

046480-01Hinged Plate (assembled at factory with72-0208#10 Flat Washer
strain gauge)72-1010F#10-32 x 5/8-Inch Pan-Head Screw

72-1408S #4-40 x 1/2-Inch Pan-Head Screw

046481-01Roll Bar72-1608F#6-32 x 1/2-Inch Pan-Head Screw

046482-01 Roll Link

046483-01Pivot Shaft72-1818F#8-32 x 1 1/8-Inch Pan-Head Screw
046484-01Detent Plate72-8806#8-32 x 3/8-Inch Socket-Head Screw
046485-01Magnet Bracket72-8808#8-32 x 1/2-Inch Socket-Head Screw

72-8810 #8-32 x 5/8-Inch Socket-Head Screw

046489-01Magnet72-8012#10-32 x 3/4-Inch Socket-Head Screw

046523-01 Detent Roller

046524-01Roller Bearing72-E00S#10-32 x .312-Inch Shoulder Screw
046525-01Detent Lever72-E8020.187-Inch O.D. Shoulder Screw

73-00824 1/8-Inch Diameter x 1 1/2-Inch Cotter Pin 046560-01 Boot Cushion

046906-01Magnet Plate75-0285,#8 Flat Washer
106007-001Loktite 29075-040S#10 Lock Washer
119008-10015 KQ Potentiometer75-0488,#8 Lock Washer

75-07007 1/4 Flat Washer 171087-001 Strain Gauge (assembled at factory with 176024-4108 hinged plate) #10-32 x 1/2-Inch Self-Locking Button- Head Screw 1/4-20 x 3/4-Inch Carriage Bolt 1/4-20 x 1 3/4Inch Carriage Bolt

Page 92

Mlustrated Parts List Hard Drivin’

Not Shown: 178012-004 Clip Bing on Clutch Shaft & Pedal 176022-3604 Set Screw on 60-Tooth Gear 107013-001 72-8612 Light Oil Socket-Head Screw 177010-236 Nut

046393-01 046390-01 Locking Tab Bumper Pad 476022-3604 046379-01 Screw 045401-01 Clutch Bearing (5 places) Tab

046391-01 Clutch Link 046385-01 Clutch Spring Nad bina a Pele

Housing 7

4 177010-238 2 72-8612 #8-32 Nut #6-32 Pan-Head 046386-01 Screw " 177010-236 3 a : #6-32 Nut 046396-01 75-0165 Brake End

#6 Washer046395-01Cap

178181-3604 Brake Com

1/4-Inch Spacer046384-01pression
|Spring ShaftSpring177000-147

Rear Cover #5/16-24 Nut 72-8808 01 106007-001 #8-32 Screw eake Loktite 290 Guide Cap 046389-01 046399-01

046394-01Stop BracketBrake Rod

Spring Front Shaft Cover 046398-01 Urethane Brake Spring 040249-01 7 A044817-01 44-Tooth Brake PCB

Spur Gear|___72-8612

Socket-Hd Screw 178181-3604 4/4-Inch Spacer

040235-01 60-Tooth Spur Gear 178026-016 Clutch Extension Rae ; 177010-236 rin aesr-o1 SPY Sy ; Nut Clutch Spring Shaft 046387-01 4" Clutch 046330-01 Spring Shaft 119008-1001 Brake & 5 KQ Pot, Clutch ff 046392-01 Hamess {7 7 178012- 046383-01 Brake 004 Clutch Pedal Switch : Clip Ring

478244-229Actuatorf

Actuator 046388-01 75-5540B Clamp ( : Pedal Pivot co c It an 41/4-20 Carriage Bolt 160044-001 177012-111 Brake Switch Push-On Spring Nut 72-8414 75-07002

Screw‘A046499-01Strain GaugeFender Washer
177010-232Brake Pedal Assy177010-244
#4-40 Nut(includes strain1/4-20 Nut

gauge and hamess) Figure 4-7 Clutch And Brake Pedal Assembly A046380-01 A

4-18

Page 93

Illustrated Parts List

Clutch and Brake Pedal Assembly Parts List

Part No.DescriptionPart No.Description
A044817-01Brake PCB Assembly046398-01Urethane Brake Spring
A046330-01Brake/Clutch Harness Assembly046399-01Brake Rod
A046499-01Brake Pedal Assembly (includes strain106007-001Loktite 290
gauge and strain gauge harness)107013-001Light Oil

040249-01 14-Tooth Spur Gear with Hub (Acceptable

substitute is part no. 046050-02 when used119008-10015 KQ Clutch Potentiometer
with part no. 72-8404, screw cap, and part160044-001Snap-Action Brake Switch
no. 106007-001, adhesive.)171087-001Strain Gauge (assembled at factory with
045401-01Spring Housing Spacer (Acceptable substi-brake pedal and shaft)
tutes are part nos, 178266-6620, 178266-176022-3604#6-32 x 1/4-Inch Socket-Head Screw

3620, 178266-7620, 178266-0620, 178266-

2620.)177000-147#5/16-24 Nut

177010-232 #4-40 Nyloc Nut

046379-01Clutch Bearing Tab177010-236#6-32 Nyloc Nut
046383-01Clutch Pedal177010-238#8-32 Nyloc Nut

046384-01 Cover over Rear Spring Shalt

046385-C1Clutch Spring Housing177010-2441/4-20 Nyloc Nut

177012-111 Push-On Spring Nut

046386-013-Inch Clutch Shaft178012-0043/8-Inch Diameter Clip Ring
046387-014-Inch Clutch Shaft178026-016Clutch Extension Spring

046388-01 Pedal Pivot Shaft

046389-01Stop Bracket178181-36041/4-Inch Spacer

178244-220 Actuator Clamp

646390-01Bumper Pad72-8412#4-40 x 3/4-Inch Socket-Head Screw
046391-01Clutch Link72-8612#6-32 x 3/4-Inch Pan-Head Screw
046392-01Brake Switch Actuator72-8808,#8-32 x 1/2-Inch Pan-Head Screw
046393-01Locking Tab75-01581/4 Flat Washer
046394-01Cover over the Front Spring Shaft75-0168#6 Flat Washer
046395-01Brake Compression Spring175-5520B1/4-20 x 1 1/4-Inch Black Carriage Bolt
046396-01Brake End Cap75-5540B1/4-20 x 2 1/2-Inch Carriage Bolt
046397-01Brake Guide Cap75-07002Fender Washer

4-19

Page 94

Illustrated Parts List Hard Drivin’

f 107012-001 Dry Teflon Spray Lubricant

039236-01 Pivot Pin

039240-01 Foot Pedal Accelerator

040028-01 \ Pedal Compression eee Spring 178012-004 \ Retaining Ring

a“ 039242-01 _———__ Cable

039238-01 039703-01 Pulley Cable Extension Spring ———_—_______, Cap screw of pulley must be in this position when pedal is fully open (at rest).

72-8606 #6-32 Socket 039704-01 Head Screw Pedal Extension Spring

039239-01 Foot Pedal Control Base Plate

119008-1001 eis 5 KO Pot

Red

All parts shown above make up the Foot Control Assembly, part no. A039235-03. The Foot Control Assembly is a large subassembly of the Gas Pedal Assembly, part no. A046403-01.

046298-01 Foot Pedal Bracket

75-0108 Ne #10 Washer lot Shown: A0a3947-01 177010-240 Gas Pedal Harness Assy #10-24 Locknut

Figure 4-8 Gas Pedal Assembly A046403-01 E

4-20

Page 95

Illustrated Parts List

Gas Pedal Assembly Parts List

Part No. Description Part No. Description A039235-03 Foot Control Assembly. Replaceable Parts: 107012-001 Dry Teflon Spray Lubricant

039236-01Pivot Pin178012-004Retaining Ring for 3/8-Inch-Diameter
039238-01PulleyShaft
039239-01Foot Pedal Control Base Plate119008-10015 KQ Potentiometer
039240-01Foot Pedal Accelerator72-8606#6-32 x .38-Inch Socket-Head Screw
039242-01CableA043947-01Gas Pedal Harness Assembly
039703-01Cable Extension Spring046298-01Foot Pedal Bracket
039704-01Pedal Extension Spring177010-240#10-24 Polymer Locknut
040028-01Pedal Compression Spring75-0108#10 Flat Washer

4-21

Page 96

Illustrated Parts List Hard Drivin’

99-10140 Panel Assembly 75-9485 Locknut

99-10116 Lever 99-10152 5) Right Coin Inlet y 99-10147 Harness 171006-035 Coin Mechanism

75-944S Locknut

99-10096 Fastener

99-10151 Left Coin Inlet

70-11-47 Lamp 7

99-10080 :

Lamp Socket » _ ave } ; 99-10105 72-9408S y Bw 1G y Bar Screw 4 ‘

99-10104 Bar Retainer

Qed Qi 99-10042 thru 99-10045 99-10154 Coin Switch Assembly

Bracket Assembly

99-10153, . Coin Return Box 99-10150 Switch Cover 99-10068 Coin Chute

160057-001 Coin Switch

99-10075 thru 99-10078 Switch Wires 99-1008 Retainer 7514128

Screw

Figure 4-9 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

Page 97

Ulustraied Parts List

5s 5 2 . . 68 2 5 te g cy © o &5 £5 g 8 22 3s 28 2 2325 wo» zo Ee Be 53 Se =e 2° ¢0 Ep &5 82 ey. & as gs

ge ao ae ae BS ae bet ge Bt 3 a S 5

8 is} oO 99-10142 Button Housing

99-10119 Button Assembly

i Se 99-10148 Lock Assembly

os

NOTE The acceptable substitute for this door (and the ‘one used in games manufactured in Ireland) is the Coin Controls, inc. Coin Door Assembly, part number 171034-001 is} g =5 B 2s \ x 68 Fa @ a \ 8 S ge 8 <

25 ‘83 ® Zs 2%

83 Ze z8 cB 38 a5 3 7 BO

Figure 4-9 Coin Acceptors, Inc. Coin Door Assembly, Continued 171027-001 A

Page 98

Illustrated Parts List

Coin Acceptors , Inc. Coin Door Assembly Parts List

Part No.DescriptionPart No.Description
160057-001Coin Switch99-10081Key Holder
70-11-47Miniature Bayonet Lamp99-10096Fastener
72-940684.40 x 3/8-Inch Truss-Head Screw99-10104Bar Retainer
72-HA1404C4-40 x 1/4-Inch Pan-Head Screw99-10105Bar
72-JA1405B#4-40 x .31-Inch Pan-Head Screw99-10115Spring
75-14128#4-40 x 3/4-Inch Pan-Head Screw99-10116Plastic Coin Return Lever
75-9948#4-40 Locknut99-1017Steel Coin Return Door
99-1008Retainer99-10139Coin Door
99-10042Coin Switch Assembly for Belgian 5 Frand—99-10140Coin Door InnerPanel Assembly
US. 25¢99-10141Die-Cast Coin Return Cover
99-10043Coin Switch Assembly for German 1 DM,99-10143Coin Door Frame
Japanese 100 Yen, Swiss 1 Fr99-1014Channel Clip

99-1004 Coin Switch Assembly for German 2 DM,

Italian 100 L, U.S. $1.0099-10147Harness
99-1045Coin Switch Assembly for Australian $.20,99-10148Lock Assembly
German 5 DM, British 10 P99-10149Service Door

99-10150 Switch Cover 99-10068 Coin Return Chute

99-10075Switch Wire (included in coin switch as-99-10151Left Coin Inlet
sembly 99-10043)99-10152Right Coin Inlet
99-10076Switch Wire (included in coin switch as-99-10153Coin Return Box
sembly 99-10042)99-10154Bracket Assembly

99-10077 Switch Wire (included in coin switch as-

sembly 99-10044)99-10160L-Inch Wide Die-Cast Coin Inlet Housing

99-10161 25¢ Amber Side-Entry Coin Button Assem-

99-10078Switch Wire (included in coin switch as-bly
sembly 99-10045)99-1506Screw for Clamp
99-1080Lamp Socket171006-035Metal Coin Mechanism for U.S, 25¢

4-24

Page 99

Hard Drivin’ Illustrated Parts List

N O T E S

4-25

Page 100

Illustrated Parts List

179231-002 2-Position Terminal Block

4179211-001 Terminal Block Jumper A046346-02 45-Inch Wht Jumper Assy \ A043367-01 Jumper Assy

A046346-01 15-Inch Blk Jumper Assy Not Shown 034544-01 Fuse Block Cover

149005-002 5, 15 A Hitron Power Supply

\ =) Ame @

@

cy By A042384-01 Line Filter Assy

14808-7022 7 Amp, 250 V Fuse

j oR 1792252205 ||ra e ® ® ® 5-Position Fuse Block

° =)

14608-3022 3 Amp, 250 V Fuse option i 4044431-01 a APU PCB Assy 2 Amp, 250V Fuse 142044-001 Lge Transformer

Figure 4-10 Power Supply Assembly A046345-01 A

Page 101

Hard Drivin’ Illustrated Parts List

Power Supply Assembly Parts List

Part No.DescriptionPart No.Description
A042384-01Line Filter Assembly146008-20222 Amp, 250V Slow Blow Fuse
‘A043367-01Jumper Assembly14608-30223 Amp, 250 V, Slow Blow Fuse
A044431-01Hard Drivin’ Audio Power Unit (APU) PCB14608-6272.(6.25 Amp, 250 V, Slow Blow Fuse
Assembly149005-0025 V, 15 A Hitron Switching Power Supply
A046346-0115-Inch Black Jumper Assembly(see below)
A046346-0215-Inch White Jumper Assembl179211-001Terminal Block Jumper

ly Jump:

034544-01Fuse Block Cover17925-22055-Position Fuse Block
142044-001‘Transformer179231-0022-Position Terminal Block

Hitron 5V, 15 A Switching Power Supply Sub-Assembly Parts List

Part No.DescriptionPart No.Description
‘Transistors99-211026Resistor, Carbon Film, 330 Ohm, 5%, 1/4W
99-211002‘Transistor, NPN, 2SC1413A99-211027Resistor, Carbon Film, 5.6 Ohm, 5%, 1/4W
99-211003Transistor, NPN, PESO30B99-211028Resistor, Carbon Film, 8.2 Ohm, 5%, 1/4W
9.211004Transistor, PNP, PE8550B99-211029Resistor, Carbon Film, 10 Ohm, 5%, 1/4W.

99-211062 Transistor, 28D725

9.211063‘Traneietor BES=50B99-211030Resistor, Carbon Film, 39 Ohm, 5%, 1/4W

99-211031 Resistor, Carbon Film, 56 Ohm, 5%, 1/4W

Diodes99-211032Resistor, Carbon Film, 1K Ohm, 5%, 1/4W
=.iife
99-211008Diode, Schottky, $10SC4M99-211033Resistor, Metal Film, 2K Ohm, 2%, 1/4W
Parepig re Re ee99-211034Resistor, Carbon Film, 180K Ohm, 5%, 1W
oo 11008ane amy oie99-211035Resistor, Carbon Film, 2K Ohm, 5%, 1/4W
=iode, Rectifier, 1N40\99-211065Resistor, Wire Wound, 27 Ohm, 5%, 2W
Resi‘lm,6.%, 1/2
99-211009Diode, Fast Recovery, RpglOB99-211066esistor, Carbon Film, 6.8 Ohm, 5%,1/2W
ee airPi tee Ne uaeeen99-211067Resistor, Carbon Film, 12 Ohm, 5%, 1/4W
$o011012Frag ete ghey ad99-211068Resistor.Carbon Film, 2.4 Ohm, 5%, 1/2W
Diode, Switching, 1N4199-211077Resistor, 470 Ohm, 1/2W, 5%
gepuibesDede erssea99-211078Resistor, 120K Ohm, 1W, 5%
99-211076Diode, 31DQ04co
:_ipacitors

99-211013 Rectifier, Silicon Controlled, $2800

icon Goninon99-211036Capacitor, Metal Film, 0.047UF, 250V
Resistors99-211037Capacitor, Metal Film, 0.22UF, 100V
;—99-211038Capacitor, Metal Film, 0.1UF, 400V
99-211014Potentiometer, Trimming, 3K Ohmpainsiiss.
ppn1i015Rasisioe Wie Wound 26 Olin, 0%, 2.99-211039Capacitor, Metal Film, 0.022UF, 100V
99-211016Resistor, Wire Wound, 150 Ohm, 5%, 2W‘,
99-211017Resistor, Wire Wound, 33 Ohm, 5%, 2Wetpraia Siar or a Bu
;Capaciic,0.2
99-211018Resistor, Wire Wound, 0.47 Ohm, 5%, 2Weo anesCinenee peeves TOPIC, CSP
99-211019Resistor, Wire Wound, 120 Ohm, 5%, 2W:*,i
99-211020Thermistor, 0.5 Ohm, 5%, 5W.a.
;;»5%,99-211044Capacitor, Electrolytic, 470UF, 25V
99-211021Resistor, 2.2K Ohm, 2%, 1/4W99-211045Capacitor, Electrolytic, 220UF, 25V
-211046itor,Elic, 100
99-211022Resistor, Carbon Film, 330 Ohm, 5%, 1/2Wso2ti047Caractoe pena appOuE 25y
99-211023Resistor, Carbon Film, 270 Ohm, 5%, 1/2W:;,
99-211024Resistor, Carbon Film, 470 Ohm, 5%, 1/4Wz‘lytic,22
99-211025Resistor, Carbon Film, 47 Ohm, 5%, /4W —— 3o's11046borewrneemaitipcigy

4-27

Page 102

Illustrated Parts List

Hitron Power Supply Sub-Assembly, Continued Parts List

Part No.DescriptionPart No.Description

99-211069 Capacitor, Electrolytic, 2200UF, 16V

99-211070Capacitor, Electrolytic, 220UF, 25V‘Transformers
99-211079Capacitor, De7100F22M99-211075Transformer, Power
99-211080Capacitor, 1000UF, 35V99-211083‘Transformer, Power

-21108 Transformer, 4.75MH

99-211081Capacitor, 470UF, 25Vgolorionaania ii
99-211082Capacitor, 220UF, 16V99-211085Transformer

99-211090 Capacitor, Ceramic, 1000PF, 2KV

99-211091Capacitor, Electrolytic, 2200UF, 10V.Miscellaneous
Inductors99-211001Regulator, UAASLAWC

«| 99-211 se, 2A, 250V

ionpanes cle 36MM99-211057Terminal Block, 8CKT
-2»UH, 35:-2112A, 250V,
99-211052Inductor, 15MHcaiamatiBuse; 2220, stab
99-211053Inductor, 1.5MH99-211059Heatsink

99-211060 Fuse Holder, 6.35MM

99-211054Inductor, 2.2UH99-211061Heatsink, Nor
99-211071Inductor, 9.8UH-Ider
99.211084(ce: aon99-211072Fuse Holder, 5.2X20
99-211085Inductor, 9.8UH99-211073Fuse, 2A, 125V

-2110 i k, 9CKT

99-211086Inductor, 0.75MHoeratior4Terminal Block, 9

99-211087 Inductor, 2.2UH 99-211088 Inductor, 60MH

4-28

Page 103

Hard Drivin’ Mlustrated Parts List

N O T E S

Page 104

Illustrated Parts List Hard Drivin’

ar

ote i kal "7 Ie SERRE (yy Be () Be oct orite ae ¢ ‘wy — [= te Bas 8 fg Lee fg

cr siete] ie ofa ©

fo SS

Be as rye Een ror eh UES cos w $0357] = tt] x eS Sr 190% ot un

: Sie 4 a 200 210 ¢ so so SS SS SG SH BH ty 150 160 170 180 740 Brg Chae

So ae fa ie , Pe S19 & B oxo TSR on Ig on

200s je, cxgeg ar fe, go oO ss, cm cr Sts 1005 ne IE le le

et 34 oo ay Ths fo: a os 5 getty

Figure 4-11 Hard Drivin’ Main PCB Assembly A044425-01 C

4-30

Page 105

Hard Drivin’ Illustrated Parts List

Hard Drivin’ Main PCB Assembly Parts List

Designator Description Part No. Designator Description Part No.

Integrated Circuits80YIntegrated Circuit, 74AS08137484-001
85CIntegrated Circuit, 7418374137144-001

5K Integrated Circuit, 4464, 64K X 4, DRAM 137546-003

5MIntegrated Circuit, 74F244137502-001
15BIntegrated Circuit, 7418374137144-001

15K Integrated Circuit, 4464, 64K X 4, DRAM 137546-003

15MIntegrated Circuit, 74ALS245137440-001
20PIntegrated Circuit, 74ALS574137548-001

20S, 20U Integrated Circuit, 74AS823 137513-001

20WIntegrated Circuit, 74AS823137513-001

25K Integrated Circuit, 4464, 64K X 4, DRAM 137546-003

25MIntegrated Circuit, 74AS573137547-001

30B _ Integrated Circuit, ADC0809 137243-001 30D _ Integrated Circuit, AD7582 137545-001 30P _ Integrated Circuit, 7415245 137134-001 30S, 30U Integrated Circuit, 2149, 45 nsec 137199-002

30WIntegrated Circuit, 2149, 45 nsec137199-002
30YIntegrated Circuit, 7418245137134-001

35K Integrated Circuit, 4464, 64K X 4, DRAM 137546-003

35M__Integrated Circuit, 74ALS245137440-001
40HIntegrated Circuit, 74LS123137268-001

40S, 40U Integrated Circuit, 2149, 45 nsec 137199-002

40YIntegrated Circuit, 7418245137134-001

50B, 50D Integrated Circuit, 741$244 137038-001

50HIntegrated Circuit, 74L$123137268-001

50S, 50U Integrated Circuit, 744LS574 137548-001

50WIntegrated Circuit, 74AL8574137548-001
50YIntegrated Circuit, 7448573137547-001

55L-MSP Integrated Circuit, 34010-50 137538-002 60P, 60S Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002

60U, 60W Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002

65CIntegrated Circuit, 7418259137137-001

70P, 70S Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002 70U, 70W Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002

75CIntegrated Circuit, 74LS259137137-001
75HIntegrated Circuit, 74LS14137056-001

80P, 80S Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002 80U, 80W Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002 90P, 90S Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002 90U, 90W Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-00290Y Integrated Circuit, 74AS138 137522-001

95CIntegrated Circuit, 7415374137144-001
100KIntegrated Circuit, 74LS74137023-001

100M Integrated Circuit, 74ALS08 137460-001 100P, 100S Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002 100U, 100W integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002

100YIntegrated Circuit, 74AS08137484-001
110CIntegrated Circuit, 7406137052-001

110K, 110M Integrated Circuit, 74ALS138 137517-001 110P, 110$ Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no, 137553-001, Integrated Circuit, 64X%4, VRAM, 120 nsec.) 137553-002

110U, 110W Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no, 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002 120H Integrated Circuit, 74F74 137436-001

120KIntegrated Circuit, 7418393137146-001

120M Integrated Circuit, 74ALS08 137460-001

120P, 120S Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002 120U, 120W Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002 130M Integrated Circuit, 74ALS161 137470-001 130P, 130S Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002

130U, 130W Integrated Circuit, VRAM, 64KX4, 150 nsec (Acceptable substitute is part no. 137553-001, Integrated Circuit, 64X4, VRAM, 120 nsec.) 137553-002 135C, 135H__ Integrated Circuit, 74F74 137436-001

135KIntegrated Circuit, 744$32137487-001
140CIntegrated Circuit, 7418244137038-001
140HIntegrated Circuit, 7418393137146-001
140KIntegrated Circuit, 74F11137583-001

140M Integrated Circuit, 74ALS574 137548-001

150CIntegrated Circuit, 741$245,137134-001

4-31

Page 106

Illustrated Parts List Hard Drivin’

Hard Drivin’ Main PCB Assembly Parts List

Designator Description Part No. Designator Description Part No.

150EIntegrated Circuit, 741S244137038-001200Integrated Circuit, PR EPROM, 421,136052-1106
150HIntegrated Circuit, 74L$74137023-001137444-200
150KIntegrated Circuit, 741S20137060-001200TIntegrated Circuit, PR EPROM, 421,136052-1107
150PIntegrated Circuit, 74AS573137547-001137444-200
200UIntegrated Circuit, PR EPROM, 421,136052-1108
150S-PSP Integrated Circuit, 34012-50137559-0011374-200
150UIntegrated Circuit, 74F244137502-001200VIntegrated Circuit, PR EPROM, 421,136052-1109
150W Integrated Circuit, 74A$573137547-001137444-200
160CIntegrated Circuit, 7418244137038-001

200W Integrated Circuit, PR EPROM, 421, 136052-1110

160EIntegrated Circuit, 74ALS161137470-001137444-200
160HIntegrated Circuit, 74ALS32137464-001200XIntegrated Circuit, PR EPROM, 421,136052-1111
160KIntegrated Circuit, 74ALS138137517-0011374-200

160M Integrated Circuit, 74F04 137437-001

200YIntegrated Circuit, PR EPROM, 421,136052-1112
160PIntegrated Circuit, 744$573137547-001137444-200
160U__Integrated Circuit, 744$00137480-001205BIntegrated Circuit, 4066B137580-001

160W Integrated Circuit, 744$573 137547-001

170CIntegrated Circuit, 7418245137134-001210AIntegrated Circuit, MC1488137403-001
210BIntegrated Circuit, MC1489AL137263-001
170EIntegrated Circuit, 7418244137038-001210CIntegrated Circuit, RAM, 8KX8, 150 nsec 137535-006
170HIntegrated Circuit, 7415148137417-001210DIntegrated Circuit, RAM, 8KX8, 150 nsec 137535-006
170KIntegrated Circuit, 74AL$161137470-001
170PIntegrated Circuit, 7418244137038-001210EIntegrated Circuit, 48202-15, RAM137442-150
210FIntegrated Circuit, 7418245137134-001
170UIntegrated Circuit, 744808137484-001210HIntegrated Circuit, 7415244137038-001
180CIntegrated Circuit, 74AL$138137517-001210}Integrated Circuit, 7418244137038-001
180EIntegrated Circuit, 74AL$139137467-001
180S-GSP Integrated Circuit, 34010-50137538-002210KIntegrated Circuit, 7418244137038-001
210LIntegrated Circuit, 7418245137134-001
180U__Integrated Circuit, 744$573137547-001210M _ Integrated Circuit, 7418245137134001
180W Integrated Circuit, 74F04137437-001210NIntegrated Circuit, 7418244137038-001
180YIntegrated Circuit, 7448573137547-001
190CIntegrated Circuit, 7415393137146-001210PIntegrated Circuit, 7418245137134001
210RIntegrated Circuit, PR EPROM, 421,136052-1113
190EIntegrated Circuit, 744$00137480-0011374-200
190KIntegrated Circuit, 68010137414-002
190NIntegrated Circuit, 7418245137134-0012108Integrated Circuit, PR EPROM, 421,136052-1114
190UIntegrated Circuit, 744$32137487-001137444-200
210TIntegrated Circuit, PR EPROM, 421,136052-1115
190W Integrated Circuit, 74ALS74137156-0011374-200
190YIntegrated Circuit, 7418259137137-001
200AIntegrated Circuit, 68681137543-001210UIntegrated Circuit, PR EPROM, 421,136052-1116
200C, 200D Integrated Circuit, RAM, 8KX8,_137535-006137444-200
150 nsec210VIntegrated Circuit, PR EPROM, 421,136052-1117

1374-200

200EIntegrated Circuit, 48102-15, RAM137540-150
200FIntegrated Circuit, 7418245137134-001210W Integrated Circuit, PR EPROM, 421,136052-1118
200H, 200Jintegrated Circuit, 7418244137038-001137444-200
200KIntegrated Circuit, Slapstic 17137412-117210XIntegrated Circuit, PR EPROM, 421,1360521119

137444-200

200LIntegrated Circuit, 74ALS32137464-001210YIntegrated Circuit, PR EPROM, 421,136052-1120
200M Integrated Circuit, 74ALS138137517-001137444-200

200N, 200P Integrated Circuit, 7418245 137134-001

200RIntegrated Circuit, PR EPROM, 421,136052-1105Capacitors
137444-200ClCapacitor, 100 UF, 35 V, Electrolytic124000-107
C2Capacitor, .01 HF, 50 V, Ceramic122002-103

C3-C43 Capacitor, .1 UF, 50 V, Ceramic 122002-104

4-32

Page 107

Hard Drivin’ Main PCB Assembly Illustrated Parts List

Parts List, Continued

DesignatorDescriptionPart No.DesignatorDescriptionPart No.
C44-C63 Capacitor, .001 LE, 50 V, £10%122015-102R35Diode, 1N4002131048-002
C64-C78_Capacitor, .1 UF, 50 V, Ceramic122002-104CR6Diode, MV5053, Light Emitting131027-002
C79Capacitor, 10 pF, 100 V, Ceramic122016-100CRT, CRB Diode, 1N4002131048-002
€80-C82Capacitor, .1 KF, 50 V, Ceramic122002-104CRO-CR12 Diode, MV5053, Light Emitting131027-002
C83, C84 Capacitor, 100 pF, 100 V, Ceramic122016-101R13Diode, 1N4002131048-002
87Capacitor, .1 pF, 50 V, Ceramic122002-104CRIADiode, MV50SS, Light Emitting131027-002
C88-C91Capacitor,.22 UF, 56V, Ceramic——-122015-224R17Diode, 1N4733 A, 5.1 V, Zener131009-206
92Capacitor, .1 HF, 50 V, Ceramic122002-104CRI8, CRI9 Diode, 1N4002131048-002
CR20°Diode, 1N4742 A, 12 V, Zener131009-215
C93Capacitor, 10 UF, 35 V, Electrolytic124000-106
€94-C106. Capacitor, .1 UF, 50 V, Ceramic122002-104Transistors
108-C111 Capacitor, 22 UF, 50 V, Ceramic12.Ql, Q2 Transistor, 2N6044133042-001
C112-C118Capacitor, .1 LF, 50 V, Ceramic203.Integrated Circuit, 7905137581-001
;.;;Q4Integrated Circuit, 7812137597-001
C119Capacitor, 3900 pF, 50 V, Ceramic122020-39205Transistor, 2N3904133041.001
C120Capacitor, 560 pF, 50 V, Ceramic122020-561
C121Capacitor, 10 pF, 35 V, Blectrolytic124000-1066Transistor, 283906133040-001
€122Capacitor, .0022 UF, 100 V, Plastic121022-222G7Transistor 2N3004133041.001
;.;Q8Transistor, 2N'3906133040-001
C123Capacitor, 1 UF, 50 -V, Ceramic122002-10469Transistor 2N3004133041.001
C124Capacitor, .1 WF, 30 V, Ceramic122002-104
C125-C128Capacitor, 10 uF, 35 V, Electrolytic124000-106Q10Transistor, 2N3906133040-001
€129-C137 Capacitor, .1 UF, 50 V, Ceramic122002-10411-013 Transistor, 2N3904133041.001
C138Capacitor, 1000 pF, 100 V, Ceramic——-122016-102Resistors
C139Capacitor, 1000 pF, 100 V,Cerami16-102
C141Capacitor, 1 UF, 30 V, Ceramic192002-104R27-R45__Resistor, 1 K Q, #5%, 1/4 W110000-102
coe,R46-R48Resistor, 470 Q, +5%, 1/4 W110000-471
€142Capacitor, 22 UF, 50 V, CeramicPenaRAD-RS4Resistor, 4.7 K Q, #5%, 1/4 W110000-472
C143Capacitor, .1 HF, 50 V, CeramicvenaR55, R56 Resistor, 100, +5%, 1/4 W110000-101
144Capacitor, .1 WF, 50 V, Ceramic122002-104:
C145Capacitor, 10 HF, 35 V, Electrolytic124000-106R57, R58 Resistor, 1 K Q, £5%, 1/4 W110000-102
°°’ROLResistor, 4.7 K Q, £5%, 1/4 W110000-472
C146-C227 Capacitor, .1 [UF 50 V, Ceramic122002-104R62, R63 Resistor, 220 Q, +5%, 1/4 W110000-221
C28itor,001 UF, 50 V, +10%122015-102
Seee ee EepoteROAROTResistor, 5.6 K Q, 45%, 1/4 W110000-562
€229Capacitor, 47 pF, 100 V, Ceramic122016-470;:
€230-C249 Capacitor, .1 JF, $0 V, Ceramic122002-104ROBResistor, 1 K Q, £5%, 1/4 W110000-102
a°,ROOResistor, Metal Film, 56 K Q, +1%110011-5602
250Capacitor, 47pF, 100 V, Cerami122016-470V4 w
Cac cameien i ur 50 V, ecumicR70-R73_Resistor, 220 2, £5%, 1/4 W110000-221
C274Capacitor, 47 pF, 100 V, Ceramic122016-470.
5,abe7.AR74, R75 Resistor, 10 K Q, 5%, 1/4 W110000-103,
222002-:aY"a
€275-C320Capacitor, .1 HF, 50 V, Ceramic122002-104RyLeeEHeh110000105
itor5vowtiR77, R78. Resistor, 4.7 K Q, 45%, 1/4 W110000-472
C322Capacitor, 10 pF, 35 V, Electrolytic124000-106::» 25%,
€323-C326Capacitor, 10 pF, 100 V, Ceramic—-122016-100R79Resistor, 47 K 2, £596, 1/4 W110000473
€330-C333Capacitor, .1 LF, 50 V, Cerami122002-104,;
,,‘aeR82, R83 Resistor, 470 Q,£5%, 1/4 W110000-471
itori84-R88Resistor, 10 K Q, 5%, 1/4 W110000-103,
336Capacitor, 100 pF, 100 V, Ceramic122016-101Riison,q
€337-C342Capacitor, -1 UF, $0 V, Ceramic122002-104R89-RIGResistor, 33 2, +5%, 1/4 W110000-330
oe C36 Capacitor, 1 BE, 2 % heirstasooe faeROB-R1O1 Resistor, 100 2, £5%, 1/4 W110000-101
347Capacitor, 10 HF, 35'V,ElectrolyticmeeR102-R107 Resistor, 33 2, 5%, 1/4 W110000-330
DiodesR1O9-R111 Resistor, 100 2, 45%, 1/4 W110000-101

R113-R115 Resistor, 100 Q, +5%, 1/4 W 110000-101 CRI, CR2_ Diode, MV5053, Light Emitting 131027-002 CR3, CR4 Diode, 1N914 131052-001

4-33

Page 108

Illustrated Parts List

Hard Drivin’ Main PCB Assembly Parts List, Continued

DesignatorDescriptionPart No.Designator—_—DescriptionPart No.
R116-R123 Resistor, 33 Q, 45%, 1/4 W110000-330Crystals
R124Resistor, 220 2, 25%, 1/4 W110000-2217
R125-R131 Resistor, 1 K 2, +5%, 1/4 W110000-102soscd ear ae ah OscillatorModuleaiogeoos
R132Resistor, 4.7 K Q, +5%, 1/4. W110000-472rystampter canter

: 1 998, XOSC3 Crystal, 50 Mhz, Oscillator Module 144008-005

R134._sResistor, 1 K Q, 45%, 1/4 W110000-102XTALL Crystal, 3.6864, Standup144000-011
R144 __ Resistor, 620 Q, £5%, 1/4 W110000-621js
R145, R146Resistor, 10 KQ, $5%, 1/4 W———-110000-103__Miscellaneous
R147, R148Resistor, 100 K Q, $5%, 1/4 W—110000-104Socket, 28 Pin, .600"179257-028

Socket, 68 Pin 179237-068

R149, R150__Resistor, 10 K Q, #5%, 1/4. W——-110000-103Socket, 64 Pin, .900*179256-064
R151, R152_Resistor, 220 Q, 25%, 1/4 W110000-221Socket, 40 Pin, .600"179257-040
R155_Resistor, 0 22, £5%, 1/4 W110005-001,
R156-R159 Resistor, 5.6 K Q, +5%, 1/4 W110000-562Socket, 20 Pin179259-020

Socket, 24 Pin, 600" 179257-024

R160, R161Resistor, 10 K Q, 25%, 1/4 W110000-103Test Pointa179051-001
R162, R163Resistor, 150 @, 45%, 1/4 W110000-151JlConnector, 12 Circuit, Header .250 Ctr179069-012
R164, R165Resistor, 10 Q, +5%, 1/4 W110000-100_—
R166Resistor, 68 Q, #396, 1/4 W110000-680J2J6Connector, 11 Circuit, Header, 100 Cr179118-011
37Connector, 60 Circuit, Header, .100 Ctr179021-060
R167Resistor, 91 Q, #596, 1/4 W110000-910J8J11 Connector, 11 Circuit, Header, .100 Ctr179118-011
RN1, RN2 Resistor Network, 470X9, +5%,118010-471ji2-Connector, 9 Circuit, Header, .250 Ctr179069-009

1/8 W, SIPCOPIN)

RN3-RNS. Resistor Network, R2R Ladder118015-001J14Connector, 26 Circuit, Header,.1X.179261-026
RNOResistor Network, 4.7KX9, +5%,118010-4721 Dual—
1/8 W, SIPCLOPIN)J15Connector, 16 Circuit, Header, .1X. — 179261-016

: 1 Dual

swSwitch, 8 Pos DIP160031-008

4-34

Page 109

Hard Drivin’ Illustrated Parts List

N O T E S

4-35

Page 110

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 111

Illustrated Pans List

Shifter PCB Assembly Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.

Capacitors Transistors

C1Capacitor, .1 UF, 50 V, Ceramic122002-104QU, Q2 Integrated Circuit, TDA2030137301-001
C2Capacitor, .22 UF, 50 V, Ceramic122015-224Q3Integrated Circuit, 7815, Standup137598-001
C3Capacitor, .1 WF, 50 V, Ceramic122002-104Q6Transistor, TIP33, 40 V, 80 W133044-001
C4 — Capacitor, .001 HF, 50 V, Ceramic122002-102= Q7_—“Transistor, Mps-U07, 100 V, 2133003-001
C5Capacitor, .22 HF, 50 V, Ceramic122015-224Resistor
C6Capacitor, 22 UF, 35 V, Electrolytic124000-226RLResistor, 10 K Q, +5%, 1/4 W119000-103
C7-C14 Capacitor, .1 MF, 50 V, Ceramic122002-104= R2_———«Resistor, 1 0, #596, 1/4 W110000-010
C15-C18_Capacitor, 3300 HE, 25 V,123003-3383, R4_ Resistor, 22 K Q, 45%, 1/4 W110000-223
Electrolytic, RadialR5Resistor, 1 K Q, +5%, 1/4 W110000-102
C19 — Capacitor, .1 F, 50 V, Ceramic122002-104RG_—«Resistor, 10 2, 45%, 1/4 W110000-100
20, C21 Capacitor, 3300 UF, 25 V,123003-338 = R7___séResistor, 1 K Q, 25%, 1/4 W110000-102
Electrolytic, Radial.RS, RO Resistor, 22 K Q, 5%, 1/4 W110000-223
€22Capacitor, 22 UF, 35 V, Electrolytic124000-226R10Resistor, 1 Q, +5%, 1/4 W110000-016
23Capacitor, .22 1F, 50 V, Ceramic122015-224
;R11Resistor, 10 K Q, +5%, 1/4 W110000-103
C24Capacitor, .1 JF, 50 V, Ceramic122002-104R29——~Resistor, 47 2, 45%, 1/4-W110000.470
€25Capacitor, .001 UF, 50 V, Ceramic122002102R21__Resistor, 1 K Q, +5%, 1/4 W110000-102
€26Capacitor, .22 UF, 50 V, Ceramic122015-224R22, R23 Resistor, 1, +5%, 1 W, Carbon Film—116030-010

C27 ~~ Capacitor, .1 UF, 50 V, Ceramic 122002-104 28 lectrol 4009-106 _— ms nor , 9-1 Hanes

25.Capacilon 1 UR'50.V, CeramicToagoa-iogEMD, 2 Fusectip179050-002

vee HS1, HS2 Heatsink, TDA2030 178190-032

DiodesHS3/Heatsink, 7815178190-124
:Connector, 2 Ckt, Header, .156 Ctr179213-002

CRI-CR6 Diode, 1N4001 131048-001

CR7-CR12 Diode, 1N5401131051-002Connector, 9 Circuit, Header, 156 Ctr.179213-009
CRI9Diode, 1N5401131051-002Connector, 3 Ckt, Header, .156 Ctr179213-003

Connector, 6 Ckt, Header, .156 Cur 179213-006 ose Connector, 9 Circuit, Header, .156 Ctr. 179213-009

FU2Fuse, 3 Amp, 250 V, Norm146007-3022
Page 112

Mlustrated Parts List

4-38 88 @ SAWUD IuvLY

O€94uT ta HOMWASSY Cal Iddd te oF of wal dTHS ynt cr7 EF —EI-

ct [_ice_¢

ene Tsiesa _ LSieaA ‘gee eS Ra

oi Rit ebJiL_lé [hye ZEbEhOY

Figure 4-13 Shifter PCB Assembly A043932-01 C

Page 113

Illustrated Parts List Hard Drivin’

Shifter PCB Assembly Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.

Capacitors Transistors

clCapacitor, .1 LF, 50 V, Ceramic122002-104QlTransistor, FET, IRF630133039-001
C2, C3 Capacitor, 47 pF, 100 V, Mica128002-470Q4__Integrated Circuit, 7905137581-001
C4Capacitor, 100 UF, 25 V, Electrolytic124010-107«QS_—_—Inntegrated Circuit, 7805137596-001
C5Capacitor, 4700 UF, 25 V, Electrolytic,123021478= Q6_—Transistor, 2N3906133040-001

Radial Resistors

C6Capacitor, 1 UF, 50 V, Ceramic122002-104R1Resistor, 100 K Q, 45%. 1/4 W110000-104
C7Capacitor, 100 pF, 100 V, Ceramic122016-101R2Resistor, 270 Q, $5%, 1/4 W110000-271
C8Capacitor, 100 LIF, 25 V, Electrolytic124010-107RSResistor.1K @, 45%, 1/4 W110000-102
2, COCapacitor, -1 UB 50 V, Censisic122002-104RG, R7_ Resistor, 510 Q, 45%, 1/4 W110000-511
C13-C17_Capacitor, .1 LF, 50 V, Ceramic122002104RgResistor, 10 K Q, #5%, 1/4 W110000-103
C19Capacitor, .1 1F, 50 V, Ceramic122002-104Rg—sResistor, 1 KO, 45%, 1/4 W110000-102
C18Capacitor, 100 pF, 100 V, Ceramic122016-101R10Resistor, 2.2 K Q, 45%, 1/4 W110000-222
€20, C21 Capacitor, 1000 UF, 25 V, Electrolytic,123003-102R11 __ Resistor, 100 Q, +5%, 20 W (Acceptable Substitute is
Radialpart no. 116027-101)116025-101
C22Capacitor, 1 UF, 50 V, Electrolytic124001-105R12Resistor, 68 K Q, £5%, 1/4 W110000-683
€23-C30, C74 Capacitor, .1 HF, 50 V, Ceramic122002-104R13, R14 Resistor, 10 K Q, +5%, 1/4 W110000-103

, R19, R20. Resistor, 1.2 K Q, 45%, 1/2 W 110001-122

DiodesR21Resistor, 22 K Q, 5%, 1/4 W110000-223
CR1Diode, 1N4001131048-001
CR2Diode, 1N5401131051-002R22Resistor, 2.2 K Q, 5%, 1/4 W110000-222
C3Diode, 1N4005131048-005-R23_Resistor, 4.7 K Q, 45%, 1/4 W110000-472
CR5Diode, MV5053, Light Emitting131027-002R24, R25_ Resistor, 3 K Q, 5%, 1/4 W110000-302
R26Resistor, 330 Q, 5%, 1/4 W110000-331
CR6Diode, 1N100131053-001
CR7Diode, 1N4001131048-001R27, R2B- Resistor, 4.7 Q,1W110030-047

R29, R30 Resistor, 348 Q, 1 W 10029-3480

Integrated CircuitsR31Resistor, 1 K Q, +5%, 1/4 W110000-102
IC1, 1C2_Integrated Circuit, 7418163 A137114-001-R32_—_—Resistor, 47 K ©, £59, 1/4 WAHONO0-475
IC3___Integrated Circuit, 74HCTOO137606-001.
IC4, ICS __ Integrated Circuit, 7418163 A137114-001R33Resistor, 100 Q, 45%, 1/4 W110000-101
1C6Integrated Circuit, 7414137017-001R34Resistor, 39 K Q, 45%, 1/4 W110000-393
R35Resistor, 2.2 Q, +5%, 1/4 W110000-022
IC7Integrated Circuit, 7418374137144001-R36_—_—Resistor, 348. 2, 1 WLieb S480
IC8Integrated Circuit, DAC-08137159-001.‘
ICOIntegrated Circuit, 7418374137144-001R134Resistor, 0 2, +5%, 1/4 W110005-001
IC10__Integrated Circuit, TLO82CP137584-001ellancous
IC11 _ Integrated Circuit, ADOPO7CN137523-001-HS1_—_-Heatsink, TDA2030178190-032
IC12Integrated Circuit, 74HCTOO137606-001——JP1-3Connector, Rept, 2 Ckt179178-002
L1Inductor, 3.3 HH141023-001-J1-J5Connector, 3 Circuit, Header, 156 Ctr179213-003
J6Connector, 26 Circuit, Header, .1X.179261-026

Fuse 1 Dual

PTC1Fuse, Current, PTC, 9 4, 50V146011-090-_-JP1-JP3 Connector, 3 Ckt, Header, .100 Ctr179048-003

4-39

Page 114

Illustrated Parts List Hard Drivin’

OPA114

82, 1/2W

M5053 Cc + 1000UF, 25V

10UF, 20V

330, 1/2W

Figure 4-14 Brake PCB Assembly A044817-01 B

4-40

Page 115

Illustrated Parts List

Brake PCB Assembly Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.

Capacitors Resistors

ClCapacitor, 1000 UF, 25 V, Electrolytic123012-108RLResistor, 10, +5%, 1/4 W110000-100
C2, C3 Capacitor, .1 HF, 50 V, Ceramic122002-104R3_Resistor, 330 Q, +5%, 1/2 W110001-331
C4Capacitor, 470 [LF, 16 V, Electrolytic123004-471R4Resistor, 1 K Q, +5%, 1/4 W110000-102
C5-C7 Capacitor, .1 UF, 50 V, Ceramic122002-104RSResistor, 2.2 MQ, 45%, 1/4 W110000-225
C8 — Capacitor, 10 WF, 20 V, Tant127001-106R6Resistor, 1 K Q, 45%, 1/4 W110000-102
C9Capacitor, .001 WF, 50 V, £10%122015-102R7Resistor, 10 K Q, 45%, 1/4 W110000-103
C10Capacitor, .1 WE, 50 V, CeramicR8_Resistor, 1 K Q, 45%, 1/4 W110000-102
ROResistor, 270 K Q, +5%, 1/4 W110000-274

Diodes

CRIDiode, 1N4740, 10 V, Zener131009-113R10-R12__Resistor, 1 K Q, £5%, 1/4 W110000-102
CR2Diode, MV5053, Light Emitting131027-00;cous
Integrated CircuitjlConnector, 9 Circuit, Header,179213-009
ICLIntegrated Circuit, OPALI1137576-001156 Ctr, Key 3

Transistor

QlIntegrated Circuit, 7812137597-001
Page 116

Hlustrated Parts List Hard Drivin’

N O T E S

Page 117

8:00 AM 9:00 AM 10:00 AM 11:00 AM

Noon 1:00 PM 2:00 PM 3:00 PM 4:00 PM 5:00 PM 6:00 PM 7:00 PM 8:00 PM 9:00 PM 10:00 PM 11:00 PM Midnight 1:00 AM 2:00 AM 3:00 AM 4:00 AM 5:00 AM 6:00 AM 7:00 AM Hard Drivin’ Statistics Sheet

Statistics Information

Left Coins: Laps by Track:

Right Coins:aXtended Games by Track: ___
Idle Mins:aNo X Games by Track:

Active Mins: Champ Laps

Xtnded Plays:_Champ Wins
1-X Games:_Inst Rpls:

2-X Games: Rpl Aborts; N-X Games: Rpi Sec:

Auto Games: Total Credits: Error Count: Avg Time/Credit: Total Games:

Histogram Information 0-99 280-299 ——

100-119300-319——_
120-139320-339——_

140-159 340-359 160-179 360-379

180-199380-399—_
200-219_400-419—__

220-239 420-439 240-259 440-459 —

260-279460-UP_—_

Games Played by Day and Hour

Mon Tue Wed Thu Fri Sat Sun

Page 118

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 119

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller's plant; and
  • Seller’s examination of said products discloses to Seller’s satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 120

AM

ATARI

GAMES

Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, CA 95035