CATHODE RAY TOMES

Carnival

Carnival (upright, AY8912 music) (Sega, 1980) · Manual · 46 pages · 42 sections · original scan

Page 1

Owner’s Manual

A a ee a

Page 2

CARNIVAL Operating Instructions Service Manual

and

Copyright * 1980 by GREMLIN/SEGA INDUSTRIES, INC. All rights reserved.

Page 3

INTRODUCTION...

This is an electronic game that makes extensive use of digital integrated circuitry and television monitor circuitry. This manual assumes the maintenance technician possesses a general knowledge of solid state circuitry microprocessor, TTL digital integrated circuitry and TV. monitor concepts. Any individual not knowledgeable in these areas should not attempt repair of the electronic portion of this game. It should be noted that any attempt to repair the game in the field without the express consent of the factory will immediately void the warranty!!!

IMPORTANT NOTES... An important service note is posted in this game and is repeated here for emphasis:

If at any time the TV. screen shows a meaningless display or the game otherwise malfunctions, simply drop a coin into the coin mechanism. This should correct the problem. If not, the game requires service.

The circuitry in this game has been arranged so that the insertion of a quarter through the coin mechanism will reset the restart in the system. This clears up temporary problems caused by power line disturbances, static, etc.

SERVICE TECHNICIAN NOTE:

The system reset circuitry described above requires that the coin counter is attached to the system. if there is a coin counter problem and no replacement is available, the game will function properly if a 10K Ohm resistor is connected across the coin counter input pins to the video logic board.

ALSO... Never replace any components with anything other than exact replacement parts. (See Parts List located on Service Schematics.)

Never remove circuit boards/connections while power is on.

Do Not replace the fuse with anything other than the proper value. A blown fuse indicates an overload condition within the game. Replacing the fuse with a higher value can cause severe damage to internal components if an overload occurs.

Always consult the manual before attempting repairs.

Correspondence regarding this game should be addressed to:

GREMLIN INDUSTRIES, INC. 8401 Aero Drive San Diego, California 92123 (714) 277-8700

Page 4

REPACKAGING INSTRUCTIONS...

Arcade 25%" Wx 67°H x 28° D 6A.77em W x 170.18em Mx 71.12em D 290 Ibs./192 kg.

Arcade Version

  • Carefully lay game on its side.
  • Attach pallet with four 5/16” - 18 x 1-3/4” bolts, as shown.
  • See Final Recrating Instructions, below.

22° Hx 21" Wx 20° D 58.88em H x 53.34em W x 50.8em D Mini-Video Version 00 the. 46 kg.

  • Place game upright inside bottom cover. St eo
  • Slide cover over game. Add protective packing material. |
  • Place top cover over side cover. 4, See Final Recrating Instructions, below.

Cocktail Version rwenn aie

  • Place game inside carton. iaeaiamale? “retaliate
  • Add protective packing material. : . _
  • Place inside protective top cover over unit. : | =

4. Close flaps and secure with shipping tape. Fee i VW

  • See Final Recrating Instructions, below. pen aj

FINAL RECRATING INSTRUCTIONS...

Place game upright. Tape down game keys. Then, crate the game using appropriate shock-absorbent packing material. Include packing on edges of game. Secure package with strapping.

Note ... If the game is to be shipped to Gremlin Industries for service or repair, attach a tag identifying the distributor and indicate the service or repair to be done. Include the full serial number of the game.

All items must be shipped prepaid.

Page 5

GAME CONCEPT...

CARNIVAL is a 1 or 2 player alternate action game that simulates a carnival shooting gallery. The playfield consists of three target rows, a rotating pipe wheel, a bonus message panel, and a ''special"' target block. The player uses a left-right control to position a rifle at the bottom of the screen, and a shoot control to fire the rifle. Two rows of bullets at the bottom of the screen indicate the number of shots remaining to the player. Every time the player shoots, one of the bullets disappears from the screen. More bullets are given during the first round than the others, so, the inexperienced player will have a chance to enjoy the play. The game ends when the piayer runs out of bullets. This can occur on any round. A round ends when the player clears the playfield of all targets. At this point, a special ''shoot the bear'' sequence appears, and when this is finished the player proceeds to the next more difficult (and higher scoring) round. This is Gremlin's Multi-Phase design concept that keeps games challenging to players of ali levels. When a player completes a round (ending with "'shoot the bear'! sequence), the screen flips to the other player. When the original player resumes play, he advances to the next level of difficulty, exactly as he would have if the screen had not flipped to the other player. This method allows the players to more directly compare their scores, since they are always within one round of each other. Note that the player who ends the game first does not necessarily lose--he might still have the higher score when the game ends. The three target rows move in a horizontal line from left to right (top row), right to left (middle row) and left to right (bottom row). There are five types of targets. The rows move as a continuous band--the targets exiting the playfield from the right side of the bottom row reappear at the left of the top row. The point value for hitting a row target is indicated along the right side of the game--maximum points for a top row target, medium points for a middle row target, minimum points for a bottom row target. These values increase from round to round. Rabbits and owls are simple targets, which disappear when hit. Numbered sign targets award additional bullets to the player when hit, as well as awarding the points indicated for the row. These targets appear only on the top two rows to make them relatively difficult targets. Five small letters, B, 0, N, U and S are randomly interspersed through the target rows. At the upper right of the playfield is the word “bonus'' spelled out is small letters. If the player manages to hit the moving bonus letters in order (b-o-n-u-s) a special bonus is awarded. The fact that the bonus is still active is shown by the bonus word in the upper right of the playfield. Every time a bonus letter in the correct order is hit, the small corresponding letter in the bonus panel enlarges to show that it has been hit. Whenever a bonus letter is hit out of order, the bonus panel disappears until the next round. The bonus panel reappears at the beginning of every round. The bonus value is determined by adding row target points into the bonus value. When the ''B' letter is hit, the bonus value freezes for that round. This encourages waiting as long as possible before attempting to score the bonus. Ducks are special targets. Whenever a duck reaches the bottom row, it is capable of leaving the row and flying down toward the player. If the duck manages to get past the player's rifle without being shot, it flies down to the bullet row and quickly eats 10 bullets. A maximum of

Page 6

CARNIVAL game concept (cont.)

three ducks can escape simultaneously. The target rows move as a continuous band of targets, and no new owls, rabbits, or bonus letter targets are added once the round starts. "More shots'' targets and ducks are added during a round. The frequency of adding duck targets is tied to the round number. As the rounds get more difficult, more ducks are added as the round progresses. A flying duck hit scores no points. Bullets left over at the end of a round earn 50 points each. The between rounds ''shoot the bear'' sequence operates as a shooting gallery bear. Whenever the bear is hit, it rears up, roars, and continues motion in the opposite direction. Each hit speeds up the bear, and increases the point value, which is shown above the bear for each hit. When the bear leaves the screen (which it will always do eventually, since it speeds up with each hit) the between rounds sequence ends and a new rourid begins. As the rounds progress, more bears ( a maximum of 4) appear on the screen simultaneously. A special yellow-rimmed score panel appears in the upper left of the playfield, and stays on for random lengths of time. Four types of panels appear here, which either add or subtract points or bullets. Hitting any part of the panel border awards the score shown inside. The bullet bonus panel is shown with a large plus sign, and a row of bullets. Immediately after appearing, the bullets begin diasappearing fairly rapidly. When the bullets are depleted, the panel disappears. If hit, the player is awarded the number of bullets left in the panel when it was hit. The score bonus is shown with the same large plus sign, and a score value. As with the bullets, the score value quickly decreases, until it hits zero and disappears. The minus panels are similar to those above except a large minus sign indicates the number of bullets or points subtracted when hit. This discourages the practice of parking on the left margin and shooting--a miss will hit the negative target. These panels show a fixed number of bullets or points, and after a random time interval, disappear. The pipe wheel contains eight pipes of four different colors. A panel beneath the wheel restricts pipe hits to horizontally oriented pipes, and also indicates the point value for hitting a pipe. Every shot the player takes decrements the pipe value, except a shot which hits a pipe. This makes it advisable to hit pipes early in the round, when it is most difficult (since the player must shoot through heavily populated target rows). Hitting two pipes of the same color with two consecutive shots awards a bonus of four times the pipe value shown in the panel. CARNIVAL is accompanied by background music. At the beginning of every round, the music begins at a slow rate and relatively low key. As the round progresses, the music speeds up and the melody shifts up in key. This gives the player a growing sense of urgency. As the round progresses, the playfield motion also gradually speeds up. A small panel on the right of the playfield contains a musical note symbol.. If the player wishes to turn off the music, he simply shoots the

note panel. This makes the note disappear, and turns off the music. Hitting the panel again makes the note reappear and resumes the music. The note thus acts as a "'flip-flop'' switch to turn the music on and off. Every round begins with the music on. There is a special case to consider near the end of a round: the player has cleared all of the targets except the ducks, and has plenty of bullets
Page 7

CARNIVAL game concept (cont.)

left so that he can simply sit and wait for the ducks. He would, in effect, prolong the game by refusing to end the round. Theoretically, by hitting the ducks and ''mre shots" signs, the round could be prolonged indefinitely. However, an internal ''doomsday'' timer in the game keeps track of how long a round has lasted. After a certain time limit (the same for each round), the frequency of new duck appearances increases dramatically.

CARNIVAL contains the following sounds: A clang sound every time a row target or bear is hit; A pipe hit sound whenever a pipe is hit; A bear roar whenever the bear is hit and rears up; Three different duck quack sounds, to accompany up to three simul taneously escaped ducks; A bonus sound for lighting the BONUS letters in the correct order; A secondary bonus sound for pipe bonus and special panel] bonus; A rank sound as the player's score moves up in rank; Background music; Rifle shot.

The top three scores are shown during advertising, along with the player's initials. A player who scores in the top three is allowed to enter three initials by a special routine explained at the time of their writing. The rank is updated during the round. The player is both audibly and visually rewarded. There is a pronounced audible sound as the player's score passes that of another ranking player's score. And, they may watch their rank progress during the game.

CARNIVAL's basic play action is outlined below, as it appears in the game instructions. Shoot all targets and pipes to advance to the next round. Game is over when you run out of bullets. Escaped ducks eat 10 bullets. Hit B-O-N-U-S letters in sequence for specia] bonus. Bonus value stops increasing when ''B'' is hit. Hit same color pipes with 2 consecutive shots to score 4 times pipe value. Shoot number signs for more bullets. Shoot the bear between rounds for extra points.

ADJUSTMENTS: Switch inside coin door turns on/off pipe hit sound during advertising sequence.

Page 8

NEW GAME BOARDS

AND NEW EPROMS...

The following chart shows the two kinds of logic boards Gremlin will use in future games. These will be either a SINGLE VIC board or a DUAL VIC board. Also shown are the possible combinations of Eprom types that Gremlin will be using. The 2 Eprom types are:

  • 2708 (holds 8K of memory)
  • 2716 (holds 16K of memory).

Obviously, the 2716 holds twice as much information as the 2708, but the 2 Eproms are not directly compatible—in other words, you have to replace a 2716 with another 2716, and a 2708 with another 2708. In addition, the 2716 Eprom socket is modified slightly to accept the 2716 Eprom. If it is ever necessary to replace a new Eprom, be sure to specify 2708 or 2716 . These numbers are printed on the Eprom package.

Logic Board Type _| Possible Eprom Types Used | Where Used

SINGLE VIC board | 1) All 2708’s HEAD-ON 1 (see photo) HEAD-ON 2 Future games

  • 2708’s and one 2716 INVINCO (used in combination) DEEP SCAN Future games

The two Eprom types are used since some game programs require a larger memory than that provided with a set of 2708’s. Usually, one 2716 provides enough additional memory space to hold a longer program.

Page 9

POWER SUPPLY MODIFICATIONS... For VIC Logic Boards Only In order to supply — 5 volts to the VIC logic board, it was necessary to modify the game power supply. The modification simply adds a 7905 — 5 volt regulator (Gremlin part #313-0023) to the power supply chassis; the 7905 is connected into the — 12 voit line at pin 11 of the power supply output connector. PIN 17 OF THIS CONNECTOR NOW BECOMES THE —5 VOLT OUTPUT. The other pins remain the same: pind1 = -12v pin 12 = +12v pin 13 = 2-3 V AC signal pins 14, 15, 16 = GROUND pin 17 = -—5v pins 18, 19,20 = +5v

Also, a 8900 ufd filter capacitor has been added to the power supply to provide better + 12 volt regulation.

TRANSFORMER VOLTAGE

CONVERSION INSTRUCTIONS...

To convert the game transformer to 100, 115, or 230 VAC, refer to the following chart:

*For 100 volts: Connect the voltage INPUT lines to transformer terminals 1 and 2.

*For 115 volts: Connect the voltage INPUT lines to transformer terminals 1 and 3.

*For 230 volts: Connect the voltage INPUT lines to transformer terminals 1 and 4. The fluorescent lamp line must be connected to transformer terminal 3.

ALSO, THE TV MONITOR MUST BE CONVERTED TO THE SAME VOLTAGE INPUT AS THE GAME TRANSFORMER. REFER TO THE MONITOR MANUAL IN THE GAME.

Page 10

MAINTENANCE PROCEDURES..DUAL games

  • Power Supply (Refer to drawing #815-0020, sheet 4)
  • Remove output connectors from power supply.
  • Make these initial tests: (GND to BLACK lead on C18, $000 ufd capacitor)

a. b. c. d. -TO ro +9 VDC on POSITIVE terminal of C18 +17-19 VY on C6 (4700 ufd cap.) -17-19 V on C5 (4700 ufd cap.) -12 V at output pin 11 (adjustable by trim pot R42) +12 V at output pin 12 (adjustable by trim pot R8) +5 V at output pins 18,19,20 (adjustable by trim pot R9)

  • GND (ground, 0 V) at pins 14,15,16 2-3 V AC at pin 13 (Don't forget to change meter scale to AC) -5 Vat pin 17
  • Check these voltages again with the logic board connected. If any are wrong, a loading condition exists in the logic board, most likely.

Logic Board

The following instructions will help you trace down and find most problems associated with the logic board. The procedures are listed by the more common kinds of problems that could arise. Read through all the steps first,

then apply them one at a time. The necessary equipment are an oscilloscope and AC/DC voltmeter.

  • NO

a. PICTURE: TV TUBE AND FLUORESCENT LAMP ARE OFF Plug the game in and check to see that it is receiving 115 (230) VAC. Measure 115 VAC at the input terminals of the game transformer. If it is not present here, proceed to next step.

Check the fuse; if it is good, proceed to next step.

Remove the cover of the junction box in back of the game. Measure 115 VAC on the output of the line filter. If it is not present, the line filter may be bad. Or, one of the AC line connections in the junction box may be loose. UNPLUG the game and re-check these connections.

\f the fluorescent lamp still does not operate, turn off game and on again. This usually re-starts the lamp. If it doesn't, turn the lamp in its socket; this will re-seat it for a better connection. Sometimes the lamp works loose during shipment.

« An ON/OFF switch for the TV monitor is located on the TV chassis, below the neck of the picture tube. Make sure it is ON.

PICTURE: TV TUBE AND FLUORESCENT LAMP ARE ON. SCREEN BLACK. . First, make a quick check of the monitor-to-logic board connections: Are all wires making contact with the pin connector? Are the wires secure on the monitor plug-in connector?

Page 11

3.

4.

5. b. Check to be sure UI4 is seated in its socket properly, and that no pins are bent. This IC is a Prom that develops the necessary video timing sequences. Usually if one pin on the chip is out of the circuit, the screen will appear black. Proceed to next step if this chip is seated correctly.

c. Inspect the high-voltage lead coming off the monitor's high-voltage transformer. This lead attaches directly to the TV tube. Sometimes, during shipment, this wire is jostled out of contact with the transformer. Turn off the game, and carefully push the wire down, toward the transformer, to re-seat it. Now check to see if the picture comes on. If it doesn't, proceed to step d.

d. Using a voltmeter, measure the three voltages powering the logic board. These voltages, +5,-5, +12 volts can easily be measured at the power supply-to-logic board connection. If all the voltages are present, go to next step.

e. Using an oscilloscope, test for clock signals at the following points: (For the moment, don't worry about what each signal should look like: We're concerned with finding floating signals, and/or signals that are not present when they should be, and why they are not.)The scope setting is .2v/div. @ Susec., with a 10:1 probe. All clock signals, except the video signal, are about 5 volts in amplitude.

  • Check pin 6 of U50. Look for a 13-2 volt video signal. If not there, check pin 4 of U50. If it is here, USO is probably bad.
  • 1f the signal is not at .in 4 of Y55, suspect U57 and U67.
  • Check the following IC's and pins for any floating or missing signals: U13, pin 8. U22, pin 9. UIS, pins 11,12,13,14. U14, pins 1-7, 9. U19, pins 2,6,10,15. U20, pins 2,7,10,14,15. These chips make up the video timing circuit. Make sure there are no floating or missing signals on any of these chips. If there are, suspect the chip is bad.

PICTURE APPEARS: COLOR IS DISTORTED; SOME COLORS MISSING

a. Check the red, blue, and green output signals on U67, pins 4,7,9, respectively. If no signals present, suspect U67, U49, or U66.

INCOMPLETE PICTURE: RANDOM DISPLAY

a. Sometimes the game appears on the screen with parts of the picture showing incorrect information. For example, the ''HI SCORE" listings display jumbled information, while the rest of the picture is normal. The most likely cause of this problem is one of the 8 Ram IC's U69 through U76. The quickest way to find the bad Ram is simply to replace each IC, one at a time, with knowngood Rams. Be sure not to bend any pins when replacing the IC's. Also, den't overlook the possibility that one of the Ram sockets is bad.

RANDOM D/SPLAY WHEN GAME IS TURNED ON

a. Activate the coin switch a few times to see if this clears the picture. If not, turn the game off, then on again. If the jumbled display still appears, proceed to step b.

b. Check the reset circuit on the logic board. (Refer to the schematic)

Page 12

When power is first applied to the game, a reset circuit consisting of QI, Q2, U18 and U35 is triggered on to reset the microprocessor. This reset signal forces the microprocessor to start at the beginning of the game program. If the microprocessor is not reset, it will still operate—it just won't operate on the right program instructions or data, and will continually display a jumbled pattern on the screen. So, begin by checking for a 3-4 VAC signal at pin 3 of the power supplyto-logic board connector. Follow the signa! through 91, where, at the collector, a sawtooth wave appears. Then, when power is first applied, observe pin 2 of U18 as capacitor C10 slowly charges to about 3 volts. When this level is reached, U18 is triggered to change states, causing pin 3 to go high, then low. This change is inverted by UI7 and finally reaches pin 26 of the Z80. Check pin 26 of the 280 for a low-to-high signal change. If not present, one or more of the reset circuit components is bad. If it is present, proceed to step c.

The following lists some probable causes of the jumbled display pattern:

  • one or more RAMS “* one of the Eproms, UI-8, U26-33
  • The microprocessor, U 16, is bad.
  • Ub7 (7415245) is bad.
  • USI and US2 are bad.
  • Check the 3 operating voltages, +5,-5, +12 VDC.
  • GAME DOES NOT COIN UP

a. A common problem with a game that coes rot coin up is that the coin switch trip wire is out of adjustment. Usually, all that is necessary is to bend the trip wire up or down, depending on whether a heavier or lighter tension is needed.

. There may be a problem in the coin circuit on the logic board. Check U62, pins 6,8 for pulses each time the coin switch is tripped. Also, U43 and/or U62 may be bad. Suspect U45, also.

{t is possible that one of the coin counter transistors, Q3 and Qh, is bad. Determine whether or not the counter advances each time the coin switch is tripped.

Don't overlook an incorrect or faulty coin switch~to-logic board connection; sometimes these wires work loose from the coin switches.

  • PLAYER CONTROLS NOT WORKING

a. Check first to be sure all control switch connections are secure. This includes checking the black wires, or ground leads.

lf. these connections are good, make sure the control panel leads are intact inside the Molex” connector to the logic board.

If the controls still do not work, suspect U44 on the logic board. However, U44 could be good but might not be receiving the activating pulses from U24, pin 10 or U25, pin 12. Check these also.

Page 13

Recommended Spare Parts. ...

GREMLIN PART NO.

130-0001

130-0002

200-0011 253-0104

253-0120 253-0121 253-0123 253-0130 253-0133

390-0011 220-0008

220-0035 220-0066

220-0071

220-0072 475-0007 510-0014 510-0042 510-0051 (800-0076) 270-0001 514-0001 240-0007

510-0023

510-0050 800-0056 240-0091 250-0289

250-0291 510-0041

315-0019

315-0050 DESCRIPTION

speaker speaker cover Algol color monitor Plexi front monitor panel panel logo, HO2/INVINCO " " HO2/DEEP SCAN

DEEP SCAN/ INVINCO

CAR HUNT/ INVINCO

CAR HUNT/DEEP SCAN

fluorescent lamp coin counter

coin door lock and key coin mechanism, complete coin reject button & spring coin return stop (U-bolt) volume control

slide switch

coin switch

push button switch

photo coin assy. line filter, junction box fuse, 2A, slo black pushbutton control mounting/contacts for above game select switch

complete joystick joystick knob threaded rod

upper sleeve

joystick switch 2708 Eprom, blank specify by number on Eprom 2716 Eprom specify by number on Eprom UPRIGHT dual games

QTY PER 10 GAMES

|= wwnnan = =

= wo

Wwwwnwwwe =

1 set

1 set

Page 14

316-0246 316-0283 316-0287 316-0390 314-0001 34-0093 314-0099 314-0104 314-0105 315-0031 315-0039 315-0042 316-0206 475-0002 482-0010

482-0014 510-0043 color prom (NV/DS color prom HO2/DS

color prom 02/1NV

color prom CAR HUNT/DS

5551 TALS374 IC TALS245 74LS138 74LS253 280 microprocessor

RAM IC Video Interface chip (VIC) video timing prom resistor pack PE8050 transistor 2N4401 ' 6-position DIP switch Wwwwwonwuwwwyuea =

NO

The following are suggested parts for all sound boards.

313-0008 314-0042 315-0006

315-0035 315-0043 481-0006 481-0008

482-0006

482-0023 313-0004

315-0005 315-0009 LM348 1C

7406 IC CMOS 4017 IC

MM 5837 IC CMOS 4069 IC 1N914 1N5231 Zener diode 2N4403 transistor 2N4093 a LM741 IC CMOS 4013 IC CMOS 4081 IC uuu uw

Page 15

| parts [TITLE top assy 700 - 0022

CARNIVALUPRIGHT ENG WHT DWG No

DRAWN SON DUONG ENGR

CHECK A, AMBROSE 5-29-80

REVISION DESCRIPTION

Gremlin/seca

San Diego, California 92123

USE WITH 800-3076 FOR

PARTS LOCATIONS

RELEASED

oie ~

REFER TO HEXAGON CALL-OUTS ON DRAWINGS FOR THE

“LOCATION OF PARTS LISTED HERE erm Tens cr i { T

TORBA NO ANA-15AN

Page 16

Gremlin Industries, Inc.

San Diego, California 92123

700 ~ 002.2. DWG NO

PARTS |TITLE TOP ASSY List | CARNIVAL UPRIGHT ENG WHT

QTY PER ASSY

PART NO

800 - 3076 800 - 3075 140 - 0048 420 - 0494 420 — 0493 800-0122

DESCRIPTION

ASSY BASIC KIT CARNIVAL ASSY DUAL VIC LOGIC CARNIVAL ENG .

CABINET BASIC WHT

GRAPHIC , SIDE , RIGHT

GRAPHIC , SIDE) LEFT ASSY, SHIPPING KIT REF DES

Page 17

PARTS | TITLE TOP ASSY .

Gremlin Industries, Inc. lier CARNIVAL UPRIGHT ENG 700 -0023

QTY PER ASSY

PART NO DESCRIPTION REF DES BOO -3076 ASSY BASIC KIT CARNIVAL

800 - 3075 ASSY DUAL VIC LOGIC CARNIVAL ENG|

140 -0049 CABINET BASIC WOODGRAIN

800 - O122 ASSY SHIPPING KIT

Page 18

PARTS JTITLE TOP ASSY

CARNIVAL UPRIGHT ENG T00-0023

WOODGRAIN DWG NO

CHECK A, AMBROSE 5-29-80

REFER TO HEXAGON CALL-OUTS ON DRAW

‘FOR THE LOCATION OF PARTS LISTE

TORR NO 01-1600

Page 19

TITLE " — Cremba/seca | PARTS Bcey Logic. ; BOO-2075 Ge Be car CARNIVAL UPRIGHT DWG NO

DRAWN... Came

CHECK A, AMRROSE

REVISION DESCRIPTION

ORM NO. 001-1500

Page 20

TITLE

Gremlin industries Ine ne ASSY Loic 800-3075 se? A ves CARDIAL UPRIGHT DWG_NO oF 2] REV

COTY PER ASSY |

PART NO DESCRIPTION REF DES

BOO - CO58& DURL GAME VIC (20 315- COI IC EPROM 2708 020-34 B15~ DOU | - CUSTOM CHIP JUS BaIG- O63 IC CLR PROM 3QXB O44

3IG- O20G6 Ic PROM PGB

Page 21

LE Gremiin industries, inc. PARTS Tt ASS Y

San Biege, Cakfernia 92123 LIST SHT 5,6;7,8 ARE'D'S|2E|DRAWN Lie es

ILTR] DATE REVISION DESCRIPTION

A {10-1119} RELEASED B |0-27%] PERECN 356 C li-7é#) PER ECN 359 D |/-24%0| PER ECN 368 |

FORM NIA Ant.18An

Page 22

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 23

Gremlin Industries, Inc.

San Diego, California 92123

i parts [TITLE assy 800-0058 DUAL GAME YC.

QTY PER ASSY

DWG NO

PART NO

DESCRIPTION

‘REF DES

Al¢~OO0FO /C 74L£5/2S

3BI4¢-004L $C VF#SOR UIs

3It~ 0058 4C 7THLSOS UIO-OUl2, U35,056)

}| B/P- OOS? 1C V4F#L3I0 O77

3/14 -O062 1C 7#C57T4 U22, 043, US5S,UG5

314-0070 1G 7E#LS5B6 uso

3IF-O0072 4E FFLSITVF U53,U66

3/F-0073 $C 74#CS8!175 U/9,020

314-0076 1C VE#L5/57 U7

3/4-O0738 (C 74L502 U2

3/9 -O0092 /C 8216 (47, VFB

3BIF-OO9F7 1C FEELS 374 i)63 ,d6¢

3I4t-O1O4 (C 7¢L5/38 UI,034¢

3/4 -OIlOS /C 7425253 OU FEt —- FG

3/4-O0O08G tapes] —psri—] NNT ]S ITNT] = 1/4 V4#lS/or UIs

3/5-003! 1G #430 CPO CMG

3/5-0039 1G RAM 4K BD O/SPEL 2 UGLI-UTe

3BI1S~ OOF2 1C V/DEO INTERFACE

BIGB-OZ06 7/2 PROM 32KX8 CTL

390 -OG0 3 LED REL

Page 24

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 25

REVISION KRM

RELEASED

PER EGN 4094 @

FORM NO.001-1500

Page 26

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 27

800-3057 DWG NO

Gremlin Industries, Inc.

San Diego, California 92123

SH31 B OF @| REV US,UB-UIO,UI4 _ UT UL Ul- U4 ,UV-UI3

ra | TITLE 4S SEMBLY LIST | CARNIVAL SOUND

LOTY PER ASSY |

PART NO

212-0021

DESCRIPTION

CONN _/OPIN M_ PL2ZD

313-0008 3/4 -O001 Fc LM348 rec NE555 Ec MMS5837 Le Cd4069

471-O10l Fll-O102 FTI-OlOos RES 1/00 OHM 1/2W 5% RES /[K OHM [/2W 5% RES /OK OHM \/2W 5% R40, R47,R55RU3,RUB,RIZI R74,R86,R127 RI[, R33,R3S.R53,R54ROFRT) R82,RB%RASRIOZR 103, RIOS, RIO R(09-R/I1,R/28,RA29,R134R14 41/1~O1OF RES 1OOK OHM |\AW 5% RES IMEG OHM 172 W 5%0| R3,R4R8,R20- RZ ROS, R32,R39)R46,RSB Rb RT RTB,RAORH. R95, RIOO,RIZ3, RIZG,RIFSRI4S

471-O/IS3 4t71-O154 47/-O222 47/ -O22> RES 15K OHM 172 W S% RES [50K OHM 1/2 W 5% RSTROS, R98 RG'L.R1E, RAGRN4,RI24 |

471-0224 RES 220K OHM 1/2W 5%

Page 28

Gremlin Industries, Ine. PARTS San Diego, Califernia 92123 LIST

PART NO QTY PER ASSY THLEASSEMBLY | 8003057 |sH4+! B CARNIVAL SQUND OF © DESCRIPTION REF DES

47/-O225 RES 2.2 MEG OHM VZW5% R2R5-RIRIARISRIBRZP

471-0332 RES 32:3 K OHM 1/2W5%| R138

471 ~ 02333 RES 33K OHM I2W S| RI1,RI4FO

471-0334 RES 330K OHM 172W Sof Allo ,RIZ0,R193,RI41

471 ~ O395 RES 3.9MEG OHM 172 W 5% RI,RI9,R23,R24

471-0472 RES 4:7 K OHM (ZW 5%

+71 -0473 RES 47K OHM 172 Wi 5% RI3,R27,R36,R43, R50-R52 Ro3, R90, RYTRIF,RIO7, RIOB

471-OF714 RES 470K OHM 1/72W Sao] R12,R17,R31,R64,REBRE4| R92, R101, RUT

471-O512 RES 5.1K OHM 1/72W S5%| R75,RHT,RI3

FT1~OCBD RES G&K OHM I72W 5% R55

471 -O 754 RES T50K OHM I/72W 5%) R7Z,R122

45) 4F#71-O823 )—~| No RES 82K OHM 1/2WS5%| RES

481-0006 (4 DIODE INGI¢F Y INFI4F8 DI - D034

FBl- 0008 “7 DIODE ZENER IN523! D325-D38

422 -O006% XSTR 2N¢4O3 GI3- 615

482 -O0O}4 /4 XSTR 2N440) @1-03,G b-GI2Z,GIT- G2

482-0023 XSTR_ 2N4093 4,953; G/6

+ TI

Page 29

TITLE

Qremlin/seca | PARTS | aSSEMBLY COIN MECH| 800-308!

San Diego, California 92123 BUAL SBA pwc

SHEET 318 ‘D' SIZE DRAWN Mien van Jto

CHECK A.AMBKOSE 5-23

REVISION DESCRIPTION DRAFT | CHECK APPR

A | 5-23-80 RELEASED ‘ORR NO 001-1500

Page 30

Gremiin Industries, Inc.

San Diego, California 92123

TITLE

PARTS | "ASSEMBLY COIN MECH | 800-308! |sH2 | A LIST oF 4 | pev

DUAL SBA DWG NO

—EM TY PER ASSY

TM paRT No [2 DESCRIPTION

250-0285 220 -O066 220 -O00O35

CASH DOOR MODIFIED

| COIN MECHANISM LOCK FORT LOCK IR

370 - 0002 800 - 0085 240 ~ OOO! 250 -~ 0068 420 - 004-6 475 - 0007 10 510 -— OO a OPTO-/SOLATOR TIL 122 i | ASSY PHOTO CALCULATOR KNOB, VOL. CONTROL BRACKET DECAL, VOL. CONTROL POTENTIOMETER (OK. CAR. PNLMT. ‘| SWITCH, SLIDE, SPDT _| SCREW 8-32x4" TAMPER- PROOF SCREW, MECH. BH. PHL4-40xs" SCREW, SHT MTL. RH. PHL.#G | SCREW, MECIL RM. PHL 6-32x 4" WASHER, FLAT # 6 WASHER, LOCK SPLIT #@ WASHER, LOCK #4. tT | WASHER, LOCK SPLIT#S NUT HEX 8=32 NUT HEX 6-32

~(NIMITO QP] ala ~j~jefujefs|-)-)-}~)dfals + T | 7) Nut HEX 4-40 ALUMINUM RIVETS -é&"

  • SIO-OO5!
  • 220-0150 SWITCH PUSH BUTTON SLIOF

t—

aj ols} }oj/ oO! atauls¢}-}-j- COIN MECH SBA PHOTO COIN CALC

25} 800-0076

Page 31

TITLE

Gremlin Industries, Inc. PARTS ASSEMBLY COIN MECH 800-308!

San Diego, California 92123 LIST DUAL SBA DWG NO

QTY PER ASSY

PART NO DESCRIPTION REF DES

220-0008 COUNTER DIGITAL

Page 32

2 1 T REVISIONS

wont [UTRDESCRIPTIONDate | APPRRVED

f A | RELEASED wm]6-280] &)

NOTES: i. INSTALL WIRE HOLD DOWN CLIPS, ITEM 21, APPROX AS SHOWN ON PRODUCTION MOCK-UP

  • INSTALL CABLE TIES, ITEM 5, AS REQD TO DRESS WIRING
  • INSTALL GROUND STRAP, ITEM 39, AS SHOWN ON PRODUCTION MOCK -UP ZA\ XeMR TO BE MOUNTED WITH PRIMARY SOE UP . [700-0022 A
sry | cODEPART OR[NOMENCLATURE

ar PARTS LIST

BBiuensons anew mentsaGremlin Industries, Inc.
—a2a
ASECTION A-A=are —POR vanoney|eexeo|TOP ASSY
  • pera Amanase |52o-se CARNIVAL UPRIGHT

\aeaaal SIZE [CODE IDENT NO-[ORAWING NO. REN = D 700-0022 | A a

xAPPLICATIONDO_NOT SCALE DRAWING/scaLe NONESHEET 3 OF 5

7 6 5 f 4 3 2 1

Page 33

REVISIONS ZONE | LTR DESCRETION Dare | ApPRoveD @ [RELEASED Twn [E202 CE)

NOTES:

fi 2. MOUNTING NUTS NOT SHOWN ON | PLYR 2 PLYR SWITCHES. CABLE TIES, ITEM 4, FOR DRESSING. CONTROL PANEL SHOWN FROM COMPONENT WIRING SIDE

B00-3076| CARNIVAL NEXT ASSY USED ON ‘APPLICATION, D

c

B 1.00 e—

<t

TT ed = ce} m t -— f i Q _ _ 48 T Q 4\ 280-0004 | CLIP, WIRE HOLDDOWN

3/4280-0005|CABLE TIES|
2i1800-3080 | ASS'Y CONTROL PANEL HARNESS ||
an800-3078 _| ASS'Y_ CONTROL PANEL=i
reiPART ofTNONENGATURE
;rwentNe NO.Se eseRteneN

PARTS LIST fear Gremiin industries, inc. anaxes San Diege, California 92923 = eres "APPROVALS Lo A ane PRBDien var Yo [o.20.80 ASSEMBLY CONTROL PANEL COMPLETE PRECRED [5-20 wees Pee CARNIVAL UPRIGHT

SE ]S6DE WERT WO ORANG FE REV.

D800 - 3077A

10 NOT SCAIE_ORAWING

Page 34
8|76543|2|L

REVISIONS

aezone | ereDESCRIPTIONDATEED
SSA | RELEASEDail421-80.
&®&aBI] CHG'D PER _ECN 387SB[3 «6

-—@ 17 ares so crm aries OX Ormeness D “

. TonZyREAR OF BRACKET

>» y

  • iy g j Z TOON COUNTER ©) 14nes.) curour

(a A | aioe enanoee 0 if : Cc

BOK CSHOUIN) FOR REFERENCE ) SIDEVIEW DETAIL SHOWING ROUTING OF HALEN eA nD tok Ee SECTION AA

FRINTSIDE view

wf 2 NUT WIRE al 4 MOT, WEX 0-40 m2) 4 NUT. HEX G-32 ne WSHR. GPLIT LOCK We

o\|4WSHR SIT LOCK #4a
2/4CREW, SH.MITL. PUL. a6in
6[4‘SCREW, MACH Di PHL, 32 ¥a*x
7/4Lie, MALL PM, Bil. a= a0 *8
Skies ach, SCIYBICALele280-0014<TNDOF 1a"
sua220-0008CON GUNTER
4800-00762SSY_ PHOTO COM CALCULATOR
NOTES:a]010-0186JUMPER BOARD
ZY ASSEMBLIES SHOWN CITES 465) ARE AUAIL ABLEWS2]0200 - 0086ASSY WARN. COIN CALCULATOR

IN KIT FORM FROM GREMLIN INDUSTRIES. INC con rR. F CoIN CTR 2

THis WiLL ALLDu) CUSTOMER TO ADD <€CLID(HEN INSTALLED)an250-0379BRACKET COIN CALCULATOR
CALCULATOR Adit) COIN” COUNTER.irem| oe | GOREPat oRNOWENGUATURE
2 COMNIECT COIN COUNTER(S) TD HARNESS WITHAfb] GER |oii no,Oe EERPTION
WIRE NUTS Phi: 280-0075 (2 REO'D.)RIES SERGE EGEED——[DONTRAGT WO—
ZY EDGE DUNECTORS (ITEMZ) WILL BE ASSEMBLED BYBESS ae N onesGremlin Industries, Ine.
PASSING THROUGH CUTOUT FROM THE REAL AND BOLTFRACTIONS OECIMALS ANGLESSom Bites, eaitorets 908:

naAIN C v UNITING ERE 7 ML = aa,

HOOKUP. THE REMAINDER OF THE HARKNESS ASSEMBLY (/TEM2)—————— wen~~TOP ASSEMBLY

Wil EXIT THE CUTOUT 1D THE REAR <IDE. THIS 1S INTENDED 7 Co.

PREVCNT THE HARNESS FIOM DOSSIBLY INTERFERRING WITH THENOTED.PHOTO CALCULATOR

PUDTD SENSDRS. (SEE SECTION AA DETAIL.) es

FRLSE EHD ENT TFEN.

D 800-0085 B ROT AS, USED OW APPLICATION DO NOT SCALE DRAWING er or _|

Page 35

p2 INDIF | +5V

go 741802 2 1

REVISIONS zone | LTR DESCRIPTION pate | APPROVED A | RELEASED wig [ie- 18-19 FAT ZT B[PER ECN 366 W458 | 1-2-80/ hf

Qt 2N4401

Q2 PEBOSO thv

74Ls02 74LS74 &

) a3 /2neeo1 4 © N RQ +5V +5v Q Lo ‘ Opt 9 TaN GND Q Q

R2 12 5/2 Wr ub }us B 330. | c3. 741802 ty Ol,

gy] oR PART OR NOMENCLATURE Ego | TENT IDENTIFYING NO. OR DESCRIPTION PARTS LIST UNLESS OTHERWISE SPECIFIED BIMENSONS ARE IN INCHES Gremiin Industries, Inc. LERANCES ARE pas FRACTIONS DECIMALS ANGLES > XX = SCHEMATIC —

PHOTO COIN CALC.

NEXT ASSY USED ON ‘SIE c ‘CODE IDENT NO. DRAWING NO, BOO -DOT7G

APPLICATION DO_NOT SCALE DRAWING scale NON E

Page 36

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 37

ue

YI 15.46848 MKE

74504 C12 | 74604 “2A0p ZomP SL

TIMER

AG

ano |@4—> GND of |: GND TA + SOOOOOOS © -2W1@ ot c1464,c, C1yeid-2 +sv |@+++>

it | e23-2A, ©) = COIN FF

De

os

bt

D3

pz

DI

og.

*| re “hey SV COOK

TOnLEss OTHERWISE SPECTIED DIWENSIONS. ARE. INCHES Gremlin Industries, Inc. ‘San Begs, Caeornéa 92723 cad 230-40,

REF cos. 72) Coin . cance A| Swiree th enc Ino ! I je LO or —

1DO_NOT SCALE DRAWING 1¢ —— DUAL GAME V.1.C.

DRAWING NO rz B00-0058|p

[seer A or &

Page 38

REVISIONS

RIGHT LEFTAD SOUNDr=‘ZONE | LTRDESCRIPTION‘DATE, "APPROVED
SWITCHééTee!A | RELEASEDLWA, [6-260] TdZ-
© ®'iTO JUNCTION BOX

GROUND

igO @Orrerss1o®@ooicffa

D ‘Telefe [sleP fal? le t]z]ale|s]e]>]als [ro] i @)

l

GND ©

  • im rs es Ao 2
BLK-WHTRED5NSO!

i ol

N.C.a&FRREEE Pe[6 |+s
BUK-REDN.C.5aar|=
WiREFTT
a]wees |WW eno
BLKYEL3800-3060 ‘=|=>Pe} om
560-005)FEb3]54]55 5657] 55] =9] eo] oxufialisfiaisis] 7a]REF~Smigen
ELECTROaECON COUNTERGOIN DOOR‘Boo-oowe |
CHOM!7Ef

ne WaRWESS

als607-901mfae
i PS23—
i Pea teoser=sHt
22) (6)Wg] “oro&1
1 BY32H

2 H

tyAl337
i pe344
|bDUALaHt
vasaVIC LOGIC36i
800-011637i

33} tr

  • U1 40 i iT = 7 ‘|
as=LL

az rr

B‘aTCtiT

TT j

WUNCTION BOX°1

tt PoweR ii i ‘]2]3]4]s]2]? ]3]> [rol tT INPUT| in tr -[S|oP HARNESS ba 800-3084

P&Fcas VoLumE 800-0120 CONTROL, i pzpapaps]oi7]e)i9]20] 0 zr i WV

TRANSFORMERaqSPEAKER (@)
zip CORDnNzalgo | fBent_| _wevhifrne wo.Oe DESeRIPTON
rtele24—?zIZ) P/O HARNESS_=PARTS UST
tt2GAME POWER800-3079 [BMisgng amen wees [NAGremlin industries, Inc.
Ad:SUPPLYPena Sen

822-0022

ZA TRANSFORMER OPTIONSaWIRINGDIAGRAM
1o0vnovzzovzs]2e|27]e8|
  • CARNIVAL UPRIGHT

A SHE [BOGE TERT WO BRAG REV >

NOTES:=Tear —| aD700-0022A
DO NOT SCALE DRAWINGscaLe NONESHEET 5 OF 5
8761

700-0022

Page 39

REVISIONS. DESCRIPTION RELEASED PER ECN 347 PER ECN 390 SB | 421-80 PER_ECN 414 AND 4i4.A 6-10-60

smecod QO-—I

560-0003

NOT ON P.C. BOARD BLANK KEYING PINS

OOO Nil, NC. NC) Mele

ciz Sris $erze sla Sw Olt J 1000 D/O ps IN 5231 MRS5O! | MRSC! [MRSO

whe 10pS 25 RIB QRIT 12K S1K H/ZV

cl7 /oopF

2N\7 R2I 1DK 3

Ge iia | A O7 LM UFEN ig

R20 2 R33) IK 100 KI

cay +) /Du 25V 5 IW, ‘CODE PART OR "NOMENCLATURE IDENT IDENTIFYING. NO. OR DESCRIPTION Clg Oo} PARTS LIST . a UNLESS OTHERWISE SPECIFIED Sov DIMENSIONS ARE IN INCHES Gremlin Industries, Inc. Fou ta L FRACTIONS DECIMALS ANGLES San Diego, California 92993 Xe = SCHEMATIC — POWER SUPPLY DUAL GAMES SIZE ] CODE IDENT NO. [DRAWING NO. Cc 200-0072 APPLICATION DO _NOT SCALE DRAWING SCALENON |

Page 40

4 3 2 1 REVISONS Zone] Ew DESCRIPTION Dare enoveD A | RELEASED woe [4-245 res B|PER ECN 409 web [e- 3-20] =

Dasa} “aL Dp” |

800-30571B

SEE DETACHED PARTS LIST

cone mam NOMERCLTURE | BE Loken. | oe beSeTN PARTS LIST Gremlin Industries, Inc. ‘Soni Diege, California 92123 ASSEMBLY — CARNIVAL SOUND

‘SE [CODE TERT WO: DRAWING NO, REV BOO- 32057 NEXT ASSY, ‘APPLICATION ‘DO_NOT_SCALE_DRAWING

Page 41

NOTES: sE8S OTHERWISE SPECIFIED REVISIONS:

IZ 2+ ALL INVERTERS ARE 50409 A} RELEASED WB i

RB. ALL TRANS IZTS RS ARE 2NO40!ROBEB] PER ECN 4094@wieny
or Alt gooes ane wareSonEe=

, | R50 nao

a79 ber en D Pz az RSI Bo ]2 ec} a> sons

ws017RagOKTorroy
aceOMen7s737

‘SHOT suk U4 RIB wOSph 22K ain

pi

Pr

ouck #1 oT re Riaz al hs OK 38)

Ns23)

Ris 2.2 MEG: RI9 5.9 MEGS

oa

cor aged b eal oN 10 pt ia R59 Dz

100.2.

us aioe = a

1 MEG yi cay FILM Ria4 32 22 uF

370KIMEGQVy Tatir

ATER my | cope Pa OR NOMENCLATURE

FILMQo] fBent_|_iwentieving no.Sm DESCRPTON

RID PARTS LIST SESE SPER

10829RasPiven it weesGremiin Industries, Inc.
SatacesMaes‘San Dione, Californts 92723

= ae > Ps SLHE MATIL—

NEXT ASSY USED ON ‘APPLICATION. 'DO_NOT SCALE DRAWING [CODE TDENT RO. [ORAWING RO BOO-A057 REV B

SHEET @ OF 200-3057|B

Page 42

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 43

REVISIONS mee camaro a A} RELEASED w36 | 10-17-19) BI|PER ECN 350 we |/0-48-79)" C| PER ECN 359 wig [i-22-79| DLPER ECN 368 Ws 8) | 26-65]

D

ea pn we aren? © Sete °A g me 08"! |e |__ > o =13pe @ 6 -an- LL rey yO

D> & =D=D=p epD> Sw w

. He th Ss c | @ PLACES

on=aa]4
|[|(Gace gee, tl

D ate

Dp=>D
&ae= L4ye
HOOOl) O80) 00‘(mn

sUU Gams i

—)= | 16aveaed |]:G00]=8

= - S@SES8S8E388 a = a

Q Le) ive} APLACES (8) SEE DETACHED PARTS LIST

TARTS ust Gremilin Industries, Inc. dan Binge, eatifornen 92073 ee 0 ASSEMBLY —— A ein] DUAL GAME Vi. c.

D 800-0058 |D Go NOT SEALE DRONE RE ETA [APPLICATION f 4

Page 44

REVISIONS DESCRIPTION RELEASED PER ECN 366

SEE DETACHED PARTS LIST

gry | cone NOMENCLATURE. REQD| IDENT IDENTIFYING. NO OR DESCRIPTION PARTS LIST JELESS OTHERWISE SPECIFIED [CONTRACT NO. MENSIONS ARE i Gremiin industries, inc. TOLERANCES Af FRACTIONS Deowass ANGLES ‘San Diego, California 92923 ba eed F.C. ASSEMBLY Pee ae PHOTO COIN CALC

NEXT ASSY USED _ON ‘CODE IDENT NO. [DRAWING NO. 860-0076 00 NOT SCALE p_——_| APPLICATION a \9 = Q

Q Q x

Page 45

tae REVISIONS. DESCRIPTION | one avgnoven RELEASED. ivr [ease] OC

a” Cc a \ Tyee oF : he ASE y

AX CASH Boy, PART OF ITEM@, MUST HAVE DIVIDER CRIMPED FLAT WITH PLIERS AS SHOWA)? FROM: To:

800-308)

NOMERGOSTURE Se SSRN PARTS UST Gremlin Industries, Inc. A mY — San Diegs, California 923 A OTES: ON q 2280] ASSEMBLY COIN MECH IN ITEM 25 REPLACES JUMPER BO. PN # 170-0176 IN [S-23-80 ASSY CO -0085 (ITEM 5) WHEN USED IN THIS ASSY. DUAL SBA BD PR TED SIDE OF ITEM @ To GE FACE TOWN bead basen namie REV a& D 800-308! A Ter A USED ON APPLICATION sneer 4 oF 4 8 7 6 5 t 4 1

Page 46

D

c

(2)

B

(2)

A a

O O 0 O

VIEW B-B (REAR PANEL AND DOOR REMOVED) VIEW B-B 3 2 1

REVISIONS, owe [oe BESoRIPTON A [RELEASED TM

©) < w Nu

is} i ° S x

LS 7 NOMENGLATURE eo] BF | wet no SeseSeAtnGn PARTS LIST Gremiin Industries, Inc. ‘San Diege, Catifornta 92193

NEXT ASSY USED_ON APPLICATION (DO_NOT SCALE DRAWING [CODE WENT NO. [DRAWING NO. REV | 7100-0022 A |