CATHODE RAY TOMES

Chelnov

Atomic Runner Chelnov (World) (Data East Corporation, 1988) · Manual · 47 pages · 12 sections · original scan

Page 1

CONVERSION KIT MODEL 1US35k

Installation

and

Service Manual

A

CF, / fo

DG DATA EAST USA, INC. 470 Needles Drive WB San Jose, ni California 95112 Telephone (408) 286-7080

780-0098-00

Page 2

WARNING

This equipment generates and uses radio frequency energy and if not installed and used properly, i.e., in strict accordance with the instructions manual, may cause harmful interference to radio communications. It has been tested and found to comply with

the limits for a Class A computing device persuant to Subpart J of

Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

Federal law provides severe civil and criminal penalties for the unauthorized reproduction, distribution, or exhibition of copyrighted audiovisual works and video games.

The Federal Bureau of Investigation

investigates allegations of criminal copyright infringement.

Page 3

Atomic Runner

CcHELNOV™

Video Game Conversion Kit

Model 1US35K

INSTALLATION AND SERVICE MANUAL

TABLE OF CONTENTS

SECTION 1 - GENERAL INFORMATION

A. Specific Requirements...........2.202-- 1

B. List of Materials...

c. Installation Instructions..............2

SECTION 2 - GAME INFORMATION

ot Game Options....... 2... cece ccc eee 6 B. Main Harness Connector Pin Out......... 7

c. PCB Edge Connector Pin Out........... 8

D. Standard Connection Diagrams........... 9

SECTION 3. - PCB SCHEMATIC DIAGRAMS

© 1988 DATA EAST USA, INC. 470 NEEDLES DR. SAN JOSE, CA. 95112 (408) 286-7080

SEPTEMBER, 1988

Page 4

COPYRIGHT NOTICE

CHELNOv “™ is Copyright 1988 by DATA EAST USA, INC. Sold exclusively in the United States of America and Canada by DATA EAST USA, INC. All Rights Reserved.

| WARRANTY INFORMATION

DATA EAST USA, INC. (Seller), warrants only to the original purchaser (Buyer) of its products that.the items listed below are free from defects in material and workmanship under normal use and service for the period specified:

GAME LOGIC PRINTED CIRCUIT BOARD(S) 90 DAYS

No other parts of the Seller's products are warranted.

Warranty periods are effective from date of initial shipment from Seller to Buyer. Seller's sole liability shall be, at its option, to repair or replace products which are returned to Seller during the warranty periods specified, provided:

  • Seller is fiotified promptly upon discovery by buyer that stated products are defective.

2, Such products are properly packaged and then returned, freight prepaid, to a place specified by Seller.

This warranty does not apply to products damaged during shipment and/or due to improper handling, or due to improper installation or usage, or alteration. In no event shall Seller be liable for any anticipated profits, loss of profits, loss of use, accidental or consequential damages, or any other losses incurred by the customer in connection with the purchase of a DATA EAST USA, INC. product.

EXCEPT AS SPECIFICALLY PROVIDED IN A WRITTEN CONTRACT BETWEEN SELLER AND BUYER, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

page ii CHELNOV INSTALLATION AND SERVICE MANUAL

Page 5

| 1. GENERAL INFORMATION

A. SPECIFIC REQUIREMENTS

The CHELNOV game is a one player (at a time) video game conversion kit. It is intended to be installed into an existing video game cabinet, and comes with all the necessary components to make the converted game look and play like a new dedicated game.

THE GAME TO BE CONVERTED MUST MEET THE FOLLOWING REQUIREMENTS

MONITOR: Horizontal, RGB, Negative Composite Sync. Input

POWER SUPPLY:]| +5vdc @ 7 Amp, +12vdc @ 1 Amp

B. LIST OF MATERIALS

QTY DESCRIPTION PART NOMBER| PNPRPPNBPRPYYNENNEBBPR PCB Set, CHE LNOV.......... PCB, RFI Filter Adapter, DE 0239.. Main Harness, Generic Kit (44 pin) Joystick Assy, 8 Way....ceeeseveee Pushbutton, Short, Black Pushbutton, Short, Red... Pushbutton, Short, Yellow Pushbutton, Short, Blue...... Pushbutton Holder, w/switch.. Pal Nut, Nylon...............- Control Panel Overlay - Generic.. Monitor Underlay Card, Chelnov... Decal, Side, Generic. Plex, Marquee, Chelnov... Plex, Clear, 23.75 X 7.6. Manual, Chelnov Kit...... Label Set, Pushbutton ID. Label, FCC Warning................ ++-510-0141-00 «+ +520-0083-00 «+ -036-0013-02 «+ +450-0003-00 «++350-0001-00 oe+++-350-0001-02 see ee +350-0001-04 wee 6350-0001-06 «.+-185-0001-00 «++-240-0001-01 « -800-0030-00 + -810-0032-00 + -820-0040-00 + -830-0039-00 + -660-0001-00 + -780-0098-00 + -406-0085-00

CHELNOV INSTALLATION AND SERVICE MANUAL page 1

Page 6

Cc. INSTALLATION INSTRUCTIONS

When selecting a game to convert, make sure that the Power Supply, the Monitor, and the Coin Acceptors are functional. There is nothing more frustrating than installing a conversion kit and having it not operate due to a faulty monitor or power supply. You should not expect the new logic PCB to be defective. It has been thoroughly tested and ‘burned-in' at the factory.

It is mandatory that the cabinet be wired to conform with all National and Local electric codes before the conversion is attempted. The primary power input section must have adequate noise filtering on the AC line to prevent undesirable conducted radio frequency interference (RFI). "Adequate" is defined as a filter with both common mode and differential mode filtering and a minimum current capacity of 2.5 Amp.

The Federal Communications Commission (FCC), and other regulatory agencies, require that every video game be clearly labeled with the Name and Address of the Original Manufacturer, Date of Manufacture (or Serial Number), Power requirements, Suitability for indoor or outdoor use, and the Model number of the unit. DO NOT DESTROY OR DEFACE THE ORIGINAL GAME ID TAG. In addition, the FCC requires that, after conversion, the unit must be labeled with a suitable warning stating that radio frequency interference may result from use in a residential area. An acceptable label is included with this kit.

IT IS THE RESPONSIBILITY OF THE PERSON PERFORMING THE INSTALLATION TO COMPLY WITH ALL LABELING REQUIREMENTS.

TAKING IT APART

Performing a few simple tasks when preparing a game to be converted can save you much time and effort when you are installing the conversion kit.

Find the Wiring Diagram of the game to be converted. You will need to identify the required DC power supply output wires and the monitor video and sync wires. Note the color coding of these wires, or better yet, label them as to their function. This kit contains a new Main Harness, but you will need to splice it into the existing power supply and video wiring.

Remove the existing game harness parts that will not be used in this conversion. NOTE: You are modifying only the secondary (DC from power supply) and I/O (video, speaker, and controls) sections of the wiring. DO NOT MODIFY OR REMOVE THE PRIMARY AC WIRING. The original manufacturer should have designed and built it to comply with Local and National Electrical Codes and FCC regulations. It must not be altered.

page 2 CHELNOV INSTALLATION AND SERVICE MANUAL

Page 7

Cc. INSTALLATION INSTRUCTIONS (cont.)

Remove the original game pcb from the cabinet. Remove all exterior decals, and repair any cabinet damage. Repaint the cabinet if necessary. Remove the monitor plex (or glass). If your plex has silkscreened art work on it, you will need to strip it off, or replace it with a new piece cut to the same size. Using the old Monitor Plex as a template, cut the Monitor Underlay card, supplied with this kit, to the same size as the old plex. NOTE: Be certain that the opening in the Underlay Card lines up with the monitor screen.

Remove the Marquee Plex from the game and use it as a template to cut the new Marquee Plex down to the correct size. Remove the control panel from the game and remove all controls and graphics from it. Drill and/or punch any required new holes for the control panel. Chelnov requires three "shoot" buttons. See the diagram below for a suggested control panel layout. If you are going to cover the control panel with clear plex (one piece provided with this kit), you should carefully cut it to fit the control panel at this time. Thoroughly clean the control panel so that the new control panel overlay will adhere to it aggressively.

PUTTING IT TOGETHER

Install the Control Panel Overlay by peeling off the paper backing and carefully laying the overly down on the panel. Smooth it out starting in the center and working your way out to the edges, removing all of the trapped air pockets. If possible, cut the edges of the overlay oversize and fold the excess under the panel. Cut out the button and joy stick holes. Install the BUTTON ID labels supplied with the kit.

| FrauRe 1. suggested Control Panel Layout

JUMP SHOOT SHOOT JUMP

TWIST

CHELNOV INSTALLATION AND SERVICE MANUAL page 3

Page 8

C. INSTALLATION INSTRUCTIONS (cont.)

You may wish to cover the control panel overlay and button ID labels with clear plex at this time. Install the new buttons and joy stick at this time. Refer to Figure 1 on the previous page for recommended control layout.

GAME PCB: Mount the Game PCB to a convenient wall of the cabinet, using the mounting feet and hardware supplied with the pcb.

MAIN HARNESS: The main harness provided with this kit has a 44 pin connector. Refer to Figure 2, on page 7 for wire color and function information. It must mate with the RFI Filter/Adapter. The Game pcb has a 56 pin JAMMA connector. Refer to Figure 3, on page 8 for information pertaining to signals and function as they are found on the game pcb edge connector.

POWER SUPPLY WIRING: Plug the RFI Filter/Adapter (DE0239) onto the game pcb. This Filter/Adapter is mandatory, as undesirable Radio Frequency Interference will be generated if it is not used. Plug the main harness edge connector onto the RFI Filter/Adapter. Separate the DC power wires and route them through the cabinet to the Power Supply. Try to keep the length of these wires to a minimum for best results.

NOTE: Use a minimum of two (2) wires EACH for the +5 volts and the Ground lines between the power supply and the pcb. Terminate these wires at the power supply as required.

[xore: IMPROPER WIRING WILL DAMAGE THE PCB SET AND VOID THE WARRANTY!

PLAYER CONTROL WIRING: Route the push button and joy stick wires up to their proper destinations, cut to length, and terminate as required.

MONITOR WIRING: The game outputs are Positive for the Red, Green and Blue signals, and Negative Composite Sync. If your monitor has separate Horizontal and Vertical sync inputs, hook the Composite sync to the negative Horizontal input. This method will work on most monitors. However, some model Electrohome's require that the Composite sync signal be hooked up to both the negative Horizontal and Vertical inputs. Contact your distributor for more information if you are uncertain as to how to hook up the monitor wires.

COIN DOOR: The coin counter(s) may be the 12 volt or the 6 volt type, as the game pcb utilizes an open collector drive circuit. Hook one coin counter wire to the required, positive voltage and the other wire to the coin counter signal wire from the main harness edge connector. Refer to the standard connection diagrams on page 9.

page 4 CHELNOV INSTALLATION AND SERVICE MANUAL

Page 9

Cc. INSTALLATION INSTRUCTIONS (cont.)

GRAPHICS: The monitor underlay card is pre-printed with game instructions. Install the underlay card under a clean, clear plex or glass. Check any marquee lamps for proper operation. Replace any burned out lamps. Install the CHELNOV marquee on the game. Install the two DATA EAST side decals. IMPORTANT: Install the "FCC Warning" label to the upper rear of the cabinet.

THE BIG TEST!

Remove the RFI Filter/Adapter from the game pcb, but leave the main harness connected to the Filter/Adapter. Apply power. Measure the +5 volts at the edge connector of the Filter/Adapter (at the point where it would connect to the game pcb). Adjust to +5.15 VDC using a Digital volt meter. Measure the +12 volts and the -5 volts (if any) to ensure that they are connected properly and are on the correct terminals. TURN THE POWER OFF! Now reconnect the RFI Filter/Adapter to the game pcb, and apply power once again. The attract mode video should appear on the screen. Adjust the picture size and colors on the monitor to get the optimum appearance. Adjust the Sync and Hold controls on the monitor for a stable picture. Coin it up and give it a try! Test all the controls and check the sound for proper operation.

CONGRATULATIONS! You have successfully installed your DATA EAST conversion kit. We hope that it gives you may years of successful operation.

CHELNOV INSTALLATION AND SERVICE MANUAL page 5

Page 10

| LT | ka GAME INFORMATION |

‘A. OPERATOR SELECTABLE OPTIONS

The CHELNOV game allows for operator adjustable pricing, bonus lives, difficulty, etc. These are accessed by the two 8 position dipswitches located on the main logic pcb. Tables 1 and 2 outline the available options.

TABLE 1 - DIPSWITCH 1

Game Charge 1 1 (right) 1 Coin = 2 COIN 1 1 Coin =3 2 Coin = 1 Game Charge 1 Coin = 1 (left) 1 Coin=2 COIN 2 1 Coin=3 2 Coin = 1 Attract mode sound? | Flip Screen?

Cocktail Table: OFF Upright game:

TABLE 2 - DIPSWITCH 2

Number of lives

Game Difficulty Hardest: ON. ON

Continue Yes: OFF

Mode _? No: ON FREEZE FRAME? Off: On:

page 6 CHELNOV INSTALLATION AND SERVICE MANUAL

Page 11

B. MAIN HARNESS CONNECTOR PIN-OUT

REMEMBER: In order to prevent undesirable radio frequency Do not attempt to Listed below are the game signals as they appear on the Main Harness (44 pin) connector which mates with the RFI Filter/Adapter. interference, the RFI Filter/Adapter must be used. buypass it!

FIGURE 2. MAIN HARNESS 036-0013-02

EDGE CONNECTOR WIRING

COMPONENT SIDE SOLDER SIDE

color | pin signal color |pin signal

gn1 1P DownA2P Down
yl2 | 1P UpB2P Up
or31P Leftc2P Left
rd4 1P RightD2P Right
pk5 1P Shoot 3E

6 F 7 H

1t bu8 ServiceJ
bu9 1P Shoot 1K2P Shoot 1
pu10 1P Shoot 2L2P Shoot 2
bn11 1P Game Selectrd/wh M2P Game Select
gn12 Coin 1rdNCoin 2
pu13 Coin Count 1slPCoin Count 2
bu/wh 14 TV Bluegn/wh RTV Green
wh/bk 15 Syncrd/wh sTV Red

16 T

wh17 Speaker (+)bk/wh USpeaker (-)
or18 + 12 VoltsVv
rd19 + 5 VoltsrdWw+ 5 Volts
rd20 + 5 VoltsrdxX+ 5 Volts
bk21 TV Groundbk4Ground
bk22 GroundbkZzGround

CHELNOV INSTALLATION AND SERVICE MANUAL page 7

Page 12

C. PCB EDGE CONNECTOR PIN-OUT

For your reference, these are the game signals as they appear on the edge connector of the game pcb.

SOLDER SIDEPIN #PARTS SIDE
GNDA1GND
GNDB2GND
+5Vc3+5V
+5VD4+5V

E 5

+12VF6+12V

MISTAKEN INPUT PREvENTION| # ‘ |MISTAKEN INPUT PREVENTION

COIN COUNTER 2J8COIN COUNTER 1

kK | gf

SPEAKER (-)L [ioSPEAKER (+)

M fai

VIDEO GREENN fieVIDEO RED
VIDEO SYNCP [13VIDEO BLUE
SERVICE SWITCHR | 14VIDEO GND

Ss 15

COIN SWITCH 2T | 16COIN SWITCH 1
START SWITCH 2U_ faiSTART SWITCH 1
2P CONTROL 1 UPvii181P CONTROL 1 UP
2P CONTROL 2 DOWNWiig1P CONTROL 2 DOWN
2P CONTROL 3 LEFTX | 20]1P CONTROL 3 LEFT
2P CONTROL 4 RIGHTy [211P CONTROL 4 RIGHT
2P CONTROL 5 PUSH 1z | 221P CONTROL 5 PUSH 1
2P CONTROL 6 PUSH 2a | 231P CONTROL 6 PUSH 2
2P CONTROL 7 PUSH 3b } 241p CONTROL 7 PUSH 3

c 25 d | 26

GNDe | 27GND
GNDf [28GND

page 8 CHELNOV INSTALLATION AND SERVICE MANUAL

Page 13

D. STANDARD CONNECTION DIAGRAMS

COIN COUNTERS & COIN SWITCHES

COIN sw 1 COIN NO. CoM garner 1 L_}——So

COIN SW 2

on No ~~ om Sarea 2 So o> St |

COIN COUNTER/COIN SWITCH CIRCUIT

CHELNOV INSTALLATION ANO SERVICE MANUAL page 9

Page 14

PCB SCHEMATICS

WARNING:

Due to the Multi-layer printed circuit boards used on this game, DATA EAST recommends service be performed only by qualified technicians with the equipment required for the servicing of multi-layer printed circuit boards.

Attempts to service multi-layer printed circuit boards using conventional de-soldering equipment may result in permanent damage to the printed traces and void your warranty.

HARKER KK ERR ERE IERIE REE KEKE

  • REPLACEMENT PARTS AND SERVICE * KKK KKK RRA ERE RARE RE RE REE RRERAEE

To obtain replacement parts or technicl assistance, contact the DATA EAST distributor in your area. If you require referral or further technical assistance, contact DATA EAST'S Service Department during the hours of 8:00 AM to 5:00 PM, Pacific time, Monday through Friday, at (408) 286-7080.

"VOICE MAIL"

During off hours, you may leave a "voice mail" message on (408) 286- 7074 Extension 236. It will be retrieved by the Service Department on the next business day. If you wish, you may also use this feature during the normal work day.

page 10 CHELNOV INSTALLATION AND SERVICE MANUAL

Page 15

poo teri tir Perit Pri tii 2 (az-£) vst CIS-27 54% 334)(49-SU 8-0) YANK 38-29 -SABE) YN 7K \at-b) €29-T) Sw [Gb-S26-ENGE-D maf (BRL) GI-5NAI-9 500% (38-LX37-5XaI-E) SETH (at-2) MA 7 (307 £1) (31-21 GLY (38-539-9)

Pht Jourzas ¥ (22-1)| eelealeaal & 1 @ Br

| UB

CHELNOV

BOARD

UPPER

| gee) (45-2) sora gand> a] Gaz-L)at-) (32-6 GE-Z) Bd I GnhW3TtD

] LNIGA% CH4-2) au ost LEW) ai mer 7 HLOS( t (WZ-Z) ayy tik, BH BE & Ss

<} iswaas-7

BIRK

Page 16

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 17

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 18

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 19

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 20

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 21

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 22

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 23

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 24

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 25

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 26

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 27

{> sag

e-zeyysouces| (4 -3E)

HW ©

cis |

+58) cpvesl>— efefale|sfes| STRa = (om cig solutes,

u

“UE uke

UW 3s & a Bo

“UT oe

f> swos (4-32) r——{> AS WR(4-2E) FS WRO (14 -3ED

A eENEGU (14-2E) 4 6pL equ (it -SE)

Page 28

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 29

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 30

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 31

“EGE of 4a]

mA wt STD on (ON LA

DSHIZM4-CEYIO-IE She

O05 Fy x PHL KG (2-2K8-18 Qwest [

Guvog = YAMOT Bey EEFAGS

aw] @ lf ke HCL 1 (19-47) OTE MXO-IEY SS Wek UAENRIEY ew (ie) ELK L (9. gpytrIf) Heer qe) (PU HHL 2OTIEY S> RMN (23F 78-3) ¥NGH (2-36)

{>> 1H =n 014 (2-48 )(4~ 78 (rope) Psaveunt aie) > MAI OESEY ce AMI (r-6EX016) Sen (iek0 Saw ei 2l0-TeMir)

a = Yor 3(0- SEND - D> erg (unser {> deer oreyzte)

{> wanp (a-369 [523 Nan zPliz 38) IE )(0-$8)) Ep (2b) >cpsp) (7) torte

  • (9-96) | (2-78) COON ate) (ante (2.18) |l-e) (ase) baeae) | MAP ne i732) Weunr (2-S 4-28)

(11-48)/s2° |

GI) tysez0%s] AON14H9

“ti

Hee

=| Sj iS] S wPos Ub-TENey Us- 2609-26) (1-48)

pHPos (13-70 H(9-3E)

ASH (2-26) VPas (1n-SE)

b

ko Wine (2-56) SEN MCE)

Page 32

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 33

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 34

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 35

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 36

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 37

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 38

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 39

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 40

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 41

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 42

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 43

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 44

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 45

Ewe # .

SIS Eee MES BY at ie 4 Wa OT [7 3 | S8EH “we Sa] 4d @} ff Re | BES | atl Set

7 |

1-7 Te Ig 4-2) Mc 1. >——

(8-28) Meaf>——

on ot

a

ay Ay /

y

f 2] mg [ES

s 1_2| als mn $

° [> Mc (6-3E> : oo: i : a3 uy |S 3 em 7 T 9 S t v € Zz T "

Page 46

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 47

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.