Lazarian (General Instructions) (M051-00636-A013)
Laser Battle (Zaccaria, 1981) · Document · 6 pages · 3 sections · original scan
GENERAL INSTRUCTIONS
FOR
LAZARIAN
INSTALLATION
- Unlock and open the coin box door.
- Remove four (4) "CABINET LEVELING LEGS" from inside the coin box.
- Tip the cabinet to the side and remove the shipping cleats from its bottom.
° Locate the threaded holes - one in each corner - and install the "CABINET LEVELING LECS" in them.
° Level the cabinet.
° When finished, the cabinet should be stable in the upright position.
4, Plug the game into a standard A.C. wall outlet ONLY .
Game MUST be properly grounded.
- The power ON/OFF switch is located:
° UPRIGHT MODEL: On top of the cabinet toward the back.
° MINI MODEL: In the center of the cabinet back just below the rear access door.
° COCKTAIL TABLE MODEL: Underneath the cabinet on Player No. 2's side.
LINE VOLTAGE SAFETY INTERLOCK SWITCHES
Line voltage SAFETY INTERLOCK SWITCHES have been provided for your protection. The locations of these SAFETY INTERLOCK SWITCHES are:
- UPRIGHT MODEL: Inside the rear of the cabinet on the right side of the rear access door.
PART NO. M051-00636-A013
ws 2 «
- MINI MODEL: Inside the rear of the cabinet on the right side of the rear access door.
- COCKTAIL TABEL MODEL: Inside the cabinet on the hinge side of the coin door.
When the cabinet access door(s) are secured in place, the SAFETY INTERLOCK SWITCH plunger(s) are in a fully depressed condition. The game circuit can function normally.
When any cabinet access door(s) are opened, the SAFETY INTERLOCK SWITCH plunger(s) are in a partially extended condition. This isolates the game circuit from the line voltage.
To restore power to the game circuit with the access door(s) open, gently pull the SAFETY INTERLOCK SWITCH plunger(s) out to the fully extended condition. THIS IS TO BE USED FOR SERVICING THE GAME ONLY!
TO PUT THE GAME INTO ITS CALIBRATION MODE
The game MUST be "ON". Then slide SW#7 of SWITCH PACK SW-1 to the "OFF" position. At this time the game will display a GRID PATTERN on the monitor screen. This may be used for making any one of a number of adjustments to the game.
This GRID PATTERN will remain on the monitor screen until the above SW#7 of SWITCH PACK SW-1 is returned to the "ON" position.
TO SERVICE THE CONTROL PANEL(S)
- UPRIGHT MODEL:
° The control panel is held in place by three latches, one on the left side, one -on the right side, and one in the center of the front of the cabinet.
They are spring loaded to provide constant positive pressure on their Latch plates.
They can be reached through the coin door AFTER turning power to the game off.
To release the latches, lift up and toward the center of the control panel.
Once they are released, unhook them from their latch plates.
To remove the control panel:
Raise it up and tilt it toward you until you can see the cable behind it.
Cradling the control panel between yourself and the cabinet, disconnect it from its cabling.
The control panel is now free and can be removed.
. -3-
° To reinstall the control panel(s), reverse this procedure.
- MINI MODEL:
° The control panel is held in place by two latches, one on the right side and one on the left side of the cabinet.
They are spring loaded to provide constant positive pressure on their latch plates.
They can be reached through the coin door AFTER turning power to the game off.
To release the latches, lift up and toward the center of the control panel.
Once they are released, unhook them from their latch plates.
To remove the control panel:
Raise it up and tilt it toward you until you can see the cable behind it.
Cradling the control panel between yourself and the cabinet, disconnect it from its cabling.
The control panel is now free and can be removed.
° To reinstall the control panel(s), reverse this procedure.
- COCKTAIL TABLE MODEL:
° Each control panel is held in place by several screws, two on the inside of the cabinet and three along the bottom edge of the control panel.
Turn the power off to the game.
Open the coin box door and release the two latches on the inside of the cabinet up next to the table top.
CAREFUL! !
Once they're released, unhook them from their latch plates.
Grasp the table top in the center above the coin door lifting up and to the side to tilt it open.
Remove the screws which secure the control panel in place.
To remove the control panel(s):
Disconnect it from its cabling.
The control panel is now free and can be removed.
° To reinstall the control panel(s), reverse this procedure.
REMOVAL OF THE MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY
1, UPRIGHT MODEL:
Turn the power to the game off and remove the control panel. This frees the main-display-glass so it can be lifted up.
By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out.
Loosen the screws which secure the T.V. bezel-glass-clamps in place.
Move the clamps to the side and the bezel glass may be removed.
Remove the above mentioned screws and the bezel with four bezel-glass-clamps may be removed.
To reinstall the T.V. bezel asssembly and the main-display-glass, reverse this procedure.
MINI MODEL:
Turn the power off to the game and remove the control panel.
Remove the screws which secure the glass clamping plate.
Lift out the glass clamping plate. This frees the main-display-glass so in can be Lifted up.
By putting your finger in the hole in the middle of the main-display-glass support, you can Lift it up and out.
Remove the screws which secure the T.V. bezel assembly and lift it out.
Reverse this procedure to reinstall the T.V. bezel assembly and the main-display-glass.
' -5-
- COCKTAIL TABLE MODEL:
° Remove the screws which secure the table top glass clamps in place.
Remove the table top glass.
Loosen the screws which secure the T.V. bezel-glass-clamps in place.
Move the clamps to the side and the bezel glass may be removed.
Remove the screws which secure the bezel assembly to the table top and the bezel with four bezel-glass-clamps may be removed.
To reinstall the.T.V. bezel assembly and the table top glass, reverse this procedure.
VOLUME CONTROL POT
The volume control pot is located on the Sound board. This is a somewhat smaller P.C. Board than the main game P.C.Board. It may be reached through the coin door on the UPRIGHT and models and through the rear access door on the MINI models. On the COCKTAIL TABLE models, you will have to open the table top to reach it.
To make the sounds louder, turn the pot clockwise as you face it (~~ >).
To make the sounds less loud, turn the pot counterclockwise as you face it (47).
VOLTAGE CONTROL POT
The voltage control pot is located on the Power Supply P. C. Board. It is pre-set at the factory and SHOULD NOT be tampered with at all unless the distributors service department is contacted first.
~ -6-
LAZARIAN
OPTION SWITCH SETTINGS
TITTTTTTTTTTTTTTTTTTTTTT TTT TTT TT TTT 7oiP Switch SW TTT TTT TTT TTT TTT TTT TTT | ae COINS PER PLAY SWI SWH2 SHAS SWS SWHS SWH6 SWAT SWHB 2 COINS 1 PLAY ON ON NOT” NOT
| *1 COIN | 1 PLAY | OFF ON USED USED | |
| 1 COIN | 2 PLAYS | ON OFF | |
| 1 COIN | 3 PLAYS | OFF OFF | _| |
NUMBER OF SHIPS PER PLAY ‘SWHT SWH2 SWAB SWH4 SWS SWHE SWH7 SWAB SHIPS “ON ON
- 3 SHIPS OFF ON 4 SHIPS ON OFF 5 SHIPS OFF OFF
= = SERVICE —
OO SWH1 SWH2 SWH3 SW SWAS SWE SWAT SWHB|
- CALIBRATION GRID NOT DISPLAYED a ON CALIBRATION GRID DISPLAYED OFF
TEST" COLLISION DETECTION DISABLE ON
- "GAME" COLLISION DETECTION NORMAL OFF
TITTETTTT LTT TTT ATT TTT TTT TTT LTT TOP SWITCH SRRILUITITIEUITEATETEREE TEU FETERULLTTETE “LASER FIRING CONTROL | Swe Swa2 SW#3 SW#4 SWS SWi6 SWH7 SW#S NORMAL FIRE NOT ~ON ~~
- RAPID FIRE USED OFF
- —_ = MONITOR. CONTROL SW#1 SWH2 SWH3 SWE SWES SWH6 SWAT Sw#B)
- NORMAL OPERATION ON FREEZE THE PICTURE OFF
tng a on ae remiss DIFFICULTY LEVEL SWiT SWH2 SWH3 SWHG SWE SWH6 SWAT SWS) EASY CANE ON ON
- MEDIUM GAME OFF ON DIFFICULT GAME ON OFF VERY DIFFICULT GAME OFF OFF
| ~ | BONUS SHIPS AWARDED _AT: | SWH1 SWA2 SWH3 SW SWHS SWE SWH7 SWS |
NO BONUS SHIP AWARDED = ON ~ ON 10,000 POINTS - ONE SHIP ONLY OFF ON
- 14,000 POINTS - ONE SHIP ONLY ON OFF
18,000 POINTS - ONE SHIP ONLY OFF OFF
- INCICATES FACTORY RECOMMENDED SETTINGS. PART NO. M051-00636-A011