CATHODE RAY TOMES

Dreamcast Switching power supply control

Dreamcast (Sega, 1998) · Datasheet · 17 pages · 8 sections · original scan

A component datasheet for the PSU's switching controller, not a Sega document.
Page 1

Bipolar IC

FA531 xX S eri es For Switching Power Supply Control

FA5310BP(S), FA5314P(S), FA5316P(S) B Dimensions, mm FA5311BP(S), FA5315P(S), FA5317P(S) © sop-8

oo. 8 5 @ Description The FA531X series are bipolar ICs for switching power supply control that can drive a power MOSFET. These ICs contain many functions in a small 8-pin package. With these ICs, a high-performance and compact power supply can be created because not many external discrete 1 4 components are needed. 6.05 5.3 8.203

0.20 “os @ Features

+ Drive circuit for connecting a power MOSFET op + Ir 1 i

+ Wide operating frequency range (5 to 600kHz) th . 0.6 + Pulse-by-pulse overcurrent limiting function 0.4201 1.27202 S fos + Overload cutoff function (Latch or non-protection mode ° selectable) + Output ON/OFF control function by external signal + Overvoltage cutoff function in latch mode + Undervoltage malfunction prevention function + Low standby current (90uA typical) + Exclusive choices by circuits (See selection guide on page 25) + 8-pin package (DIP/SOP) 2.0max

@ Applications + Switching power supply for general equipment 3.0min 4.5max

i 20.25, 520.1 @ Block diagram 2.542025 0.5: © FA5310BP(S)/FA531 1 BP(S)/FA5316P(S)/FA5317P(S) cs oT RT a Pin | Pin Description © 6 No. | symbol Tua vec 1 [RT Oscillator timing resistor [ose Lo 2 [FB Feedback 3 IS (+) Overcurrent (+) detection 4 GND Ground fouT 5 OUT Output 6 |vcc Power supply FB oceT* 7 CT Oscillator timing capacitor Q| + LT 8 cs Soft-start and ON/OFF control oa £ > rT oft-start ant control A. ae 3 4 s+) GND

© FA5314P(S)/FA5315P(S) Pin | Pin Description No. | symbol ee 1 [RT Oscillator timing resistor 2 [FB Feedback 3 IS (-) Overcurrent (-) detection 4 GND Ground 5 OUT Output x = jour 6 |Vvcc Power supply (46%, 70%) f Pw 7 (CT Oscillator timing capacitor Fa oce |" Q a_|cs Soft-start and ON/OFF control “o> -oiw £ > 4 FF 3 4 Is(—) GND

Page 2

@ Selection guide Type Max. duty | Polarity of overcurrent UVLO (typ.) Max. output | Application cycle (typ.) | detection ON threshold OFF threshold | Current FA5310BP(S) 46% + 16.0V 8.70V 1.54 Forward type FA5311BP(S) 70% + 16.0V 8.70V 1.54 Flyback type FA5314P(S) 46% = 15.5V 8.40V 1.54 Forward type FA5315P(S) 70% = 15.5V 8.40V 1.54 Flyback type FA5316P(S) 46% + 15.5V 8.40V 1.04 Forward type FA5317P(S) 70% + 15.5V 8.40V 1.04 Flyback type

@ Absolute maximum ratings @ Recommended operating conditions

Item Symbol Rating Unit Item Symbol Min. Max. Unit

Supply voltage Veo 31 v Supply voltage Veo 10 | 30 v Output current Oscillator timing resistance FA5310/11/14/15 lo 215 A FAS310/11 Rt 3.3 | 10 kQ FA5316/17 21.0 FAS314/15/16/17 1 10 Feedback terminal input voltage | VFB. 4 Vv Soft-start capacitor Cs O41 f 4 uF Overcurrent detection Vis 0.3 to +4 Vv Oscillation frequency fosc 5 600 kHz terminal input voltage CS terminal input current | Ics 2 mA Total power dissipation Pa 800 (DIP-8)*! | mw (Ta=25°C) 550 (SOP-8) *2 Operating temperature Topr -30 to +85 °c Junction temperature T 125 °C Storage temperature Tstg 40 to +150 °C Notes: +1 Derating factor Ta > 25°C : 8.0mW/"C (on PC board ) -2 Derating factor Ta > 25°C : 5.5mW/"C (on PC board )

@ Electrical characteristics (Ta=25°C, Vec=18V, fosc=135kHz) Oscillator section Item Symbol | Test condition Min. | Typ. | Max. | Unit Oscillation frequency fosc Rr=5.1kQ, Cr=360pF 125 135 145 | kHz Frequency variation 1 (due to supply voltage change) fav Veo=10 to 30V 1 %

Frequency variation 1 (due to temperature change) for Ta=-30 to +85°C 215 %

Pulse width modulation circuit section Item Symbol | Test condition | FA5310/14/16 FA5311/15/17 Unit Min. |Typ. [Max. | Min. | Typ. | Max. Feedback terminal source current leo Vre=0 660 |-800 |-960 | -660 | -800 |-960 | WA Input threshold voltage (Pin 2) VtH Feo | Duty cycle =0% 0.75 0.75 v VrtHFem | Duty cycle =Duax 1.80 2.30 v Maximum duty cycle Dax 43 |4e [49 [es [70 |74 |%

Soft-start circuit section Item Symbol | Test condition | FA5310/14/16 FA5311/15/17 Unit Min. |Typ. [Max. | Min. [Typ. [Max. Charge current (Pin 8) Ione Pin 8=0V -15 |-10 |-5 [-15 |-10 |-5) [ya Input threshold voltage (Pin 8) VtHeso | Duty cycle =0% 0.90 0.90 v Vruesm | Duty cycle =Duax 1.90 2.30 v

Page 3

Overcurrent limiting circuit section Item Symbol | Test condition | FA5310/11/16/17 | FA5314/15 Unit Min. | Typ. | Max. | Min. | Typ. | Max Input threshold voltage (Pin 3) Vrnis 0.21 |0.24 |0.27 |-0.21|-0.17|-0.14 |v Overcurrent detection terminal source current lis Pin 3=0V -300 | -200 | -100 |-240 |-160 }-80 | yA Delay time Trois 150 200 ns

Latch-mode cutoff circuit section

Item Symbol | Test condition Min Typ. | Max. | Unit CS terminal sink current Isinkcs_| Pin 8=6V, Pin 2=1V 25 45 65 WA Cutoff threshold voltage (Pin 8) VrHos 65 7.0 75 v

Overload cutoff circuit section Item Symbol | Test condition Min Typ. | Max. | Unit Cutoff-start voltage (Pin 2) VIH EB 26 28 3.4 v

Undervoltage lockout circuit section Item Symbol | Test condition | FA5310/11 FAS314/15/16/17 | Unit Min. | Typ. | Max. | Min. | Typ. |Max OFF-to-ON threshold voltage Voc on 15.5 |16.0 | 16.5 | 14.8 |15.5 |16.2 [Vv ON-to-OFF threshold voltage Voc oFF 8.20 [8.70 |9.20 | 7.70 |8.40 |9.10 |v

Output section Item Symbol | Test condition Min Typ. | Max. | Unit FA5310/11/14/15 | FA5316/17 L-level output Voltage Vow lo=100mA lo=50mA, 130 | 1.80 |v H-level output Voltage Vou lo=-100mA. lo=-5omA | 16.0 | 16.5 v Voo=18V Veo=18V Rise time tr No load No load 50 ns Fall time tf No load No load 50 ns

Output ON/OFF circuit section Item Symbol | Test condition Min Typ. | Max. _| Unit CS terminal source current Isource cs] Pin 8=0V -15 |-10 |-5 WA OFF-to-ON threshold Voltage (Pin 8) VtHon | CS terminal voltage OFF->ON 0.56 v ON-to-OFF threshold Voltage (Pin 8) VtHoFF | CS terminal voltage ON-OFF 0.42 v

Overall device

Item Symbol | Test condition Min Typ. | Max. | Unit Standby current Icost | Voo=14V 90 150 WA Operating-state supply current Icc oP 9 15 mA OFF-state supply current Ico oFF 14 18 mA Cutoff-state supply current Ioot 14 18 mA

Page 4

@ Description of each circuit

  • Oscillator (See block diagram) The oscillator generates a triangular waveform by charging and discharging a capacitor. CT pin voltage oscillates between an upper limit of approx. 3.0V and a lower limit of approx. 1.0V. The oscillation frequency is determined by a external resistance and capacitance shown in figure 1, and approximately given by the following equation:

f (kHz) = 10° 1 (kHz) = 7B (kQ) «Or (pF) (1) The recommended oscillation range is between 5k and 600kHz. The oscillator output is connected to a PWM comparator.

  • Feedback pin circuit Figure 2 gives an example of connection in which an optocoupler is used to couple the feedback signal to the FB pin. It is designed to be strong against noise and will not create parasitic oscillation so much, because the output impedance at the FB pin is as low as 4k to 5k. If this circuit causes power supply instability, the frequency gain can be decreased by connecting R4 and Ca as shown in figure 2. Ra should be between several tens of ohms to several kiloohms and Ca should be between several thousand picofarads to one microfarads.
  • PWM comparator The PWM comparator has four inputs as shown in Figure 3. Oscillator output © is compared with CS pin voltage ®, FB pin voltage ®, and DT voltage ®. The lowest of three inputs @, @, and ® is compared with output ©. If it is lower than the oscillator output, the PWM comparator output is high, and if it is higher than the oscillator output, the PWM comparator output is low (see Fig. 4). The IC output voltage is high during when the comparator output is low, and the IC output voltage is low during when the comparator output is high. When the IC is powered up, CS pin voltage @ controls soft start operation. The output pulse then begins to widen gradually. During normal operation, the output pulse width is determined within the maximum duty cycle set by DT voltage ® under the condition set by feedback signal @, to stabilize the output voltage. Fig. 1 Oscillator

Yaw io)

Lar Ds 3 + Dy Vour cs 2 vec t Sal b uy PWM ” comparator 7 pe") mosrer

Shunt regulator

Fig. 2 Configuration with optocoupler (FB pin input)

@ Oscillator output —— @CS pin voltage ———J- @ FB pin voltage _ EWM comparator @DT voltage _

Fig. 3 PWM comparator

@FB pin voltage

(3.6) @ Oscillator output

Fig. 4 PWM comparator timing chart

Page 5
  • CS pin circuit As shown in Figure 5 capacitor Cs is connected to the CS pin. When power is turned on, the constant current source (10,/A) begins to charge capacitor Cs. Accordingly, the CS pin voltage rises as shown in Figure 6. The CS pin is connected to an input of the PWM comparator. The device is in soft-start mode while the CS pin voltage is between 0.9V and 1.9V (FA5310/14/16) and between 0.9V and 2.3V(FA531 1/15/17). During normal operation, the CS pin is clamped at 3.6V by internal zener diode Zn. If the output voltage drops due to an overload, etc., the clamp voltage shifts from 3.6V to 8.0V. Asa result, the CS pin voltage rises to 8.0V. The CS pin is also connected to latch comparator C2. If the pin voltage rises above 7.0V, the output of comparator C2 goes high to turn off the bias circuit, thereby shutting the output down. Comparator C2 can be used not only for shutdown in response to an overload, but also for shutdown in response to an overvoltage. Comparator C1 is also connected to the CS pin, and the bias circuit is turned off and the output is shut down if the CS pin voltage drops below 0.42V. In this way, comparator C1 can also be used for output on/off control. As explained above, the CS pin can be used for soft-start operation, overload and overvoltage output shutdown and output on/off control. Further details on the four functions of the CS pin are given below.

4.1 Soft start function Figure 7 shows the soft start circuit. Figure 8 is the soft-start operation timing chart. The CS pin is connected to capacitor Cs. When power is turned on, a 10uA constant-current source begins to charge the capacitor. As shown in the timing chart, the CS pin voltage rises slowly in response to the charging current. The CS pin is connected internally to the PWM comparator. The comparator output pulse slowly widens as shown in the timing chart. The soft start period can be approximately evaluated by the period ts from the time the IC is activated to the time the output pulse width widens to 30%. Period ts is given by the following equation:

ts(ms)=160Cs(uF)... ...(2) Fig. 5 CS pin circuit

=

s gS ‘Shutoff in 8 response to g overload / e ‘overvoltage & 3.6f----------—---5 Fi —I je 8 va. Momentary " Overload or 9 overload or —_overvoltage 0.56++0.42 overvoltage ae + | Soft-start erie Time t 3% Vosm: 1.9V(FA5310/14/16) OFF mode 2.3V(FA5311/15/17) Fig. 6 CS pin waveform

Fig. 6 CS pin waveform

cT 7)

  • VCC TOA

osc a Output LY owm circuit FBI ae

Fig. 7 Soft-start circuit

FB pin voltage

Oscillator output

CS pin voltage

H OUT pin voltage L

Fig. 8 Soft-start timing chart

Page 6

4.2 Overload shutdown Figure 9 shows the overload shutdown circuit, and Figure 10 is a timing chart which illustrates overload shutdown operation. If the output voltage drops due to an overload or short-circuit, the output voltage of the FB pin rises. If FB pin voltage exceeds the reference voltage (2.8V) of comparator C3, the output of comparator C3 switches low to turn transistor Q off. In normal operation, transistor Q is on and the CS pin is clamped at 3.6V by zener diode Zn. With Q off, the clamp is released and the 10uA constant-current source begins to charge capacitor Cs again and the CS pin voltage rises. When the CS pin voltage exceeds the reference voltage (7.0V) of comparator C2, the output of comparator C2 switches high to turn the bias circuit off. The IC then enters the latched mode and shuts the output down. Shutdown current consumption is 400yA(Vcc=9V). This current must be supplied through the startup resistor. The IC then discharges the MOSFET gates. Shutdown operation initiated by an overload can be reset by lowering supply voltage Vcc below Vcc orF or forcing the CS pin voltage below 7.0V. The period tot from the time that the output is short-circuited to the time that the bias circuit turns off is given by the following equation:

tor(ms)=340Cs(uF)... .. (3)

4.3 Overvoltage shutdown Figure 11 shows the overvoltage shutdown circuit, and Figure 12 is a timing chart which illustrates overvoltage shutdown operation. The optocoupler PC1 is connected between the CS and Vcc pins. If the output voltage rises too high, the PC1 turns on to raise the voltage at the CS pin via resistor Re. When the CS pin voltage exceeds the reference voltage (7.0V) of comparator C2, comparator C2 switches high to turn the bias circuit off. The IC then enters the latched mode and shuts the output down. The shutdown current consumption of the IC is 400yA(Vcc=9V). This current must be applied via startup resistor Rs. The IC then discharges the MOSFET gates. The shutdown operation initiated by an overvoltage condition can be reset by lowering supply voltage Vcc below Vcc orF or forcing the CS pin voltage below 7.0V. During normal operation, the CS pin is clamped by a 3.6V zener diode with a sink current of 65uA max. Therefore, a current of 65uA or more must be supplied by the optocoupler in order to raise the CS pin voltage above 7.0V. Fig. 9 Overload shutdown circuit

Comparator C2 reference voltage (7.0V). ‘0 FB pin voltage CS pin voltage (3.6V) DT voltage Oscillator output i oo

Out pin output | i

Bias voltage +} or i i a LL Overload detection Overload shutdown

Fig. 10 Overload shutdown timing chart

acioov Transformes Fs premary winding

Poy Terminal

  • ™

f—uveo Oscillator

Fig. 11 Overvoltage shutdown circuit

Comparator C2 reference voltage (7.0V)

CS pin voltage (3.6V) DT voltage \ Oscillator output “ | FB pin output on Out pin output ” i

Bias voltage or

Overvoltage detection Overvoltage shutdown Fig. 12 Overvoltage shutdown timing chart

Page 7

4.4 Output ON/OFF control The IC can be turned on and off by an external signal applied to the CS pin. Figure 13 shows the external output on/off control circuit, and Figure 14 is the timing chart. The IC is turned off if the CS pin voltage falls below 0.42V. The output of comparator C1 switches high to turn the bias circuit off. This shuts the output down. The IC then discharges the MOSFET gates. The IC turns on if the CS pin is opened for automatic soft start. The power supply then restarts operation.

  • Overcurrent limiting circuit The overcurrent limiting circuit detects the peak value of every drain current pulse of the main switching MOSFET to limit the overcurrent. The detection threshold is + 0.24V for FA5310B/11B/16/17 with respect to ground as shown in Figure 15. The drain current of the MOSFET is converted to voltage by resistor R7 and fed to the IS pin of the IC. If the voltage exceeds the reference voltage (0.24V) of comparator C4, the output of comparator C4 goes high to set flip-flop output Q high. The output is immediately turned off to shut off the current. Flip-flop output Q is reset on the next cycle by the output of the oscillator to turn the output on again. This operation is repeated to limit the overcurrent. If the overcurrent limiting circuit malfunctions due to noise, place an RC filter between the IS pin and the MOSFET. Figure 16 is a timing chart which illustrates current-limiting operations.

Oscillator PI uo D Ps OUT pin CS pin E Ouput b circuit FB pin t Pw MOSFET proce |* } 0.24v. ba cts Ry RF © a IS(+) GND

Fig. 15 Overcurrent limiting circuit for FA5310/11/16/17 External output on/off control

BIAS

TH

Oscillator Pp FB pin voltage: I Seat z

Fig. 13 External output on/off control circuit

CS pin voltage (3.6V)

DT voltage Oscillator output FB pin voltage Comparator Cl reference voltage (0.42V) H H 4 H OUT pin output 1 u i

Bias voltage oN

OFF

Powered up Powered down,

Fig. 14 Timing chart for external output on/off control

CS pin voltage (3.6v):

DT voltage

Oscillator output FB pin voltage

OUT pin output :

Comparator C4 1 i Plus Reference i 1 detection] Voltage (0.24V) IS (+) pin voltage

Bias voltage. 1 i OFF ! ! a a Overcurrent limiting

Fig. 16 Overcurrent timing chart for FA5310/11/16/17,

Page 8

The detection threshold is -0.17V for FA5314/15 with respect to ground as shown in Figure 17. The operation is similar to that of FA5310B/11B/16/17 except the threshold is minus voltage compared to that which is plus voltage for FA5310B/11B/16/17. Figure 18 is a timing chart which illustrates current limiting operations.

  • Undervoltage lockout circuit The IC incorporates a circuit which prevents the IC from malfunctioning when the supply voltage drops. When the supply voltage is raised from OV, the IC starts operation with Vec=Vcc on. If the supply voltage drops, the IC shuts its output down when Vcc=Vcc ofr. When the undervoltage lockout circuit operates, the CS pin goes low to reset the IC.
  • Output circuit As shown in Figure 19, the IC's totem-pole output can directly drive the MOSFET. The OUT pin can source and sink currents of up to 1.5A or 1.0A. If IC operation stops when the undervoltage lockout circuit operates, the gate voltage of the MOSFET goes low and the MOSFET is shut down. Oscillator uvLo 2 PS OUT pin Output circuit CS pin

MOSFET

R,

Fig. 17 Overcurrent limiting circuit for FA5314/15

CS pin voltage (3.6V) DT voltage AD DARSYS Oscillator output __ FB pin voltage OUT pin output r rl mr rt r L

IS (—) pin voltage Minus [ R Comparator C4 detection | ormparare | voltage (— 0.17V)

Bias voltage OFF a a Overcurrent limiting

Fig. 18 Overcurrent timing chart for FA5314/15

Undervoltage lockout circuit

PWM comparator

Overcurrent qo

=

Fig. 19 Output circuit

Page 9

@ Design advice

  • Startup circuit It is necessary to start-up IC that the voltage inclination of VCC terminal “dVcc/dt” satisfies the following equation(4).

dVoc/dt(V/s)>1.8/Cs(uF) (4) Cs : Capacitor connected between CS terminal and GND

Note that equation (4) must be satisfied in any condition. Also, it is necessary to keep “latch mode” for overload protection or overvoltage protection that the current supplied to VCC terminal through startup resistor satisfies the following equation(5).

Icc(Lat)> 0.4mA for Vec = 9.2V .. -.(5) Icc(Lat) : Cutoff-state( = Latch mode ) ‘supply current

The detail is explained as follows.

  • Startup circuit connected to AC line directly Fig. 20 shows a typical startup circuit that a startup resistor Rc is connected to AC line directly. The period from power-on to startup is determined by Rc, Rp and Ca. Re, RD and CA must be designed to satisfy the following equations.

dVee/dt(V/s)= (1/Ca) + {(VAvE-Vecon )/Rc—Vecon/Rp-Iccst} > 1.8/(Cs(uF))... ...(6)

Ro(kQ)< (VAVE-9.2(V))K0.4 (MA) + (9.2(V)/RD(KQ) } ...---ee-(7) Vave = Vac *\/2/m : Average voltage applied to AC line side of Re Vac: AC input effective voltage Vecon: ON threshold of UVLO, 16.5V(max.) or 16.2V(max.) Iecst: Standby current, 0.15 mA(max.)

In this method, Vcc voltage includes ripple voltage influenced by AC voltage. Therefore, enough dVcc/dt required by equation (6) tend to be achieved easily when Vcc reaches to Vecon even if Vcc goes up very slowly. After power-off, Vec does not rise up because a voltage applied from bias winding to VCC terminal decreases and the current flowing Rc becomes zero, therefore, re-startup does not occur after Vcc falls down below OFF threshold of UVLO until next power-on. Fig. 20 Startup circuit example(1)

Page 10
  • Startup circuit connected to rectified line This method is not suitable for FA531X, especially concerned with re-startup operation just after power-off or startup which AC input voltage goes up slowly. Fig. 21 shows a startup circuit that a startup resistor RA is connected to rectified line directly. The period from power-on to startup is determined by Ra, RB and Ca. Ra, Re and Ca must be designed to satisfy the following equations.

dVee/dt(V/s)= (1/Ca)+{( VIN—Vecon )/RA- Vecon/Re-Iccst } > 1.8/(Cs(uF)). (8) Ra(kQ) <( VIN-9.2(V) ) 0.4(mA) + ( 9.2(V)/RB(KQ) ) }....(9)

Vin : V2 + (AC input effective voltage)

After power-off, once Vcc falls down below OFF threshold voltage, Vcc rises up again and re-startup occurs while the capacitor C1 is discharged until approximately zero because Vcc voltage rises up by the current flowing RA. This operation is repeated several times. After the repeated operation, IC stops in the condition that Vcc voltage is equal to Vecon (=ON threshold) because capacitor C1 is discharged gradually and the decreased Vcc inclination is out of the condition required by equation (4). After that, restartup by power-on can not be guaranteed even when equation (8) is satisfied. The image of that the startup is impossible is shown in Fig. 22. It is necessary to startup IC that supply current Icc(startup) to VCC is over 4mA in the condition of Tj < 100°C during Vcc is kept at Vccon(=16V, balance state at Vccon after the repeated operation.

Icc(start-up) > 4mA at Vec=Vccon, Tj<100°C, after power-off

This balance state that startup is impossible tends to occur at higher temperature. If power-on is done when Vcc is not kept at Vecon (for example:power-off is done and after enough time that C1 is discharged until Vcc can not be pulled up to Vccon), the IC can startup in the condition given by equation(8).

In some cases, such as when the load current of power supply is changed rapidly, you may want to prolong the hold time of the power supply output by means of maintaining Vcc over the off threshold. For this purpose, connect diode D4 and electrolytic capacitor C4 as shown in Fig. 23. This prolongs the hold time of the power supply voltage Vcc regardless of the period from poweron to startup. Fig. 21 Startup circuit example(2)

Startup is impossible (dVcc/dt <1.8/Cs just before Vcc reaches Vccon).

Icc>4mA is necessary for startup at Tj <100°C and dVcc/dt=0.

Power OFF

Fig. 22 A image of waveform when re-startup is impossible

La TR

MOSFET

Fig. 23 Startup circuit example(3)

Page 11
  • Disabling overload shutdown function As shown in Figure 24, connect a 11k resistor between the FB pin and ground. Then, the CS pin voltage does not rise high enough to reach the reference voltage (7.0V) of the latch comparator, and the IC does not enter the OFF latch mode. With this connection, the overvoltage shutdown function is available.
  • Setting soft start period and OFF latch delay independently Figure 25 shows a circuit for setting the soft start period and OFF latch delay independently. In this circuit, capacitance Cs determines the soft start period, and capacitance CL determines the OFF latch delay. If the overload shutdown and overvoltage shutdown functions raise the CS pin voltage to around 5V, zener diode Zn becomes conductive to charge Ct. The OFF latch delay can be thus prolonged by Ct.
  • Laying out Vcc and ground lines Figure 26 and 27 show the recommended layouts of Vcc and ground lines. The bold lines represent paths carrying large currents. The lines must have an adequate thickness.

5.Sink current setting for CS terminal Asink current to CS terminal must be satisfied the following condition to prevent from the malfunction which uncontrolled pulse output generates at OUT terminal when latch-mode protection should be operated for overvoltage.

65u\A < Ics(sink) <500uA at Ves= 6.5(V) Ics(sink) : Sink current to CS terminal

Example (for the circuit shown in Fig. 28 ) Ies(sink) = (28(V)-18(V)- 6.5(V) /7.5(kQ) & 467 (WA) < 500 (WA)

Fig. 24 Disabling overload shutdown function Fig. 25 Independent setting of soft-start period and OFF latch delay

ond)

Fig. 26 Vcc line and ground line (1) for FA5310B/11B/16/17

| An adds

“ es GY vce Our

Fig. 27 Vcc line and ground line (2) for FA5314/15

7.5kQ_ 18V Zener diode [4 _H Under 500A

vec

Fig. 28 Setting sink current for CS terminal

Page 12

@ Characteristic curves (Ta=25°C)

Oscillation frequency (fosc) vs. Oscillation frequency (fosc) vs. ambient temperature (Ta) timing capacitor capacitance (CT) 10° 138 N VA \ 137

10? _ o> 16 A z Rr=a.7kQ z x | x 3 N = 2 NY 8 135 Vec=18V 101 t Rr=10kQ

Rr=6.8kQ

10° 133 10! 10 10° 108 —25 0 25 50 5 100 CT [pF] Ta[°C]

Output duty cycle vs. FB terminal voltage (VFB) Output duty cycle vs. FB terminal source current (ISOURCE) 100 100

90 90

80 80 > FAS311/15/17 — __ |rasa11isi7 = 7 Ew 8 60 3 \

3 50 ZL FASSION ANG 2B so [FAsstoniaie ZB 40 z 40 38» 3 x» . \ \ 10 10

0s 1.0 1S 2.0 25 3.0 0 200 400 600 800 7000 Ves [V] FB terminal source current [A]

Output duty cycle vs. CS terminal voltage (Vcs) CS terminal sink current (ISINK Cs) vs. CS terminal voltage (Vcs) 100 100

90 90

80 80 ze FAS311/15/17, a 70 WA 70 g => S 60 S 0 Q 2 50 FA5310/14/16 2 so = 2 Vep<2.5V 3 LZ 3 Bw WA 40 o 30 30

20 20 ] 10 10 YY | Vep>2.9V ° jaan 05 1.0 15 2.0 25 3.0 o 1 2 3 4 5 6 7 8 9 10 Ves [V] Ves [V]

Page 13

H-level output voltage (VoH) vs. output source current (ISOURCE) FAS310/11/14/15

Vec= 18V 4 f

Ss 3 é z Q2 > | et

re rT 5 2 source [A]

L-level output voltage(VOL) vs. output sink current (ISINK) FAS310/11/14/15

Vot [V] Vec= 18V4

~

10-2 To? 5 Isink [A] 10?

IS (+) terminal threshold voltage (VTH Is(+)) vs. ambient temperature (Ta) FAS310/11/16/17

& VtH 1s(+) [mV]

25 50 Ta[°C] 8 100 FA5316/17

Veo=18V

=3 = $ é $2

,— [+]

oF 2 5 107 2 5 10° 2 Isource [A]

FA5316/17

Veo=18V

s

Le | J

oF 2 5 107 2 5 10° 2 Isink [A]

IS (-) terminal threshold voltage (VTH Is(-)) vs. ambient temperature (Ta) FA5314/15

VrHise) [mV]

50 75 100

Page 14

IS (+) terminal current (lis(+)) vs. IS (+) terminal voltage (Vis(+)) FAS310/11/16/17

oi 02 038 04 05 06

Vis(+) [V]

Supply current (Icc) vs. supply voltage (Vcc) Ordinary operation FA5310/11 any T fosc=600kHz 10 coe |__| = 9 ‘fosc=135kHz —]

az 6 £ Pry 5 BL I J.

0.2

oO 5 10 15 20 25 30 Vec [V]

Supply current (Icc) vs. supply voltage (Vcc) OFF or OFF latch mode

FAS310/11

2.0

Ico [mA]

0.6

0.4

oO 5 10 15 20 25 30 Vec [V] IS (-) terminal current (lis(-)) vs. IS (-) terminal voltage (lis(-)) FAS314/15

A

0 0.4 0.2 0.3 0.4 0.5

vise [V]

FAS314/15/16/17 " 1 10 fosc=600kHz |__|

a 9 fosc=135kHz—

Ico [mA]

0.2

0.4

0 5 10 15 20 25 30 Vec [V]

FAS314/15/16/17

2.0

Icc [mA]

0.6

0.4

0.2

  • 5 10 15 20 25 30 Vec [V]
Page 15

Application circuit

@ Example of FA5310B application circuit

ERO:

eragi-o2 3 ma +t

0.01n ESAD92M-02

  • tov

470 i 38k ERC3-06;

ERAQ1-02

ERASI~O2 +3 10A

i 4700 w

RSE hn tev OFN

Page 16

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 17

@ Example of FA5316 application circuit

ERA38-06 i ERAI5-0444

f muoroe #3 org || — ERC84-009%2 ox 31/6 if BA 43k aL 10k i pa a 39k T | it 2200 PCA 3600 aad i ERAB-05 + pr 22. 28k1008 pcai7 1k

Po2 0.38 post?

5V

ERAI5-04*4 <> ERAS 1-02 ooln ERCB4-009

ae i 10k 2200 u

Pot 3860p ERAGB-06 PcB17 tl 22. 28K 1008 cs ee

Parts tolerances characteristics are not defined in the circuit design sample shown above. When designing an actual circuit for a product, you must determine parts tolerances and characteristics for safe and economical operation.