CATHODE RAY TOMES

VS Baseball

Vs. Baseball (US, set BA E-1) (Nintendo of America, 1984) · Document · 5 pages · 10 sections · original scan

Page 1

VS.BASEBALL

(Operation Manual)

|. How to install Software ROMs

Each Software ROM is labeled with a Location Number shown on it ((QMShaded Portion illustrated below), which will indicate the corresponding location on the P.C. Board where it should be installed.

(Label on Software ROM)

“VS. Baseball” contains 12 Software ROMs, and 2 Custom ICs, which have location numbers, 1A, 1B, 1C, 1D, 2A, 2B, 6A, 6B, 6C, 6D, 8A, 8B, 2F and 8F. Each ROM and IC must be mounted into the proper IC Socket.

JK LMNPR ©

CAUTION: Make sure the Software ROMs and Custom ICs are intserted properly. (All IC notches should be facing the same direction) Nd9-10-SQW

ROM and IC Locatior P.C. Board

Caution: New Software ROMs or Custo.., ICs can only be mounted once the old Software ROMs or Custom ICs have been removed from their Sockets.
Page 2
  • Points and methods of adjustment MDS P.C. Board Game Option Settings

12345678 12345678 BOGUURG)... | SBBBHBRR|” OFF JOFFE

Switch (SW1) Settings

1234562?8

Player Defense (Weak) 1 | OFF | OFF

Strength1PdOFFON

3 | ON | OFF

(Strong) 4ONON
Player Offense1OFF | OFF
Strength2OFF | ON

3 ON | OFF 4 ON | ON

Computer Defense1OFF | OFF
Strenath2OFF | ON

3 ON | OFF 4 ON | ON

Computer Offense1OFF | OFF
Strength2OFFON

3 ON | OFF 4 ON | ON

Note:For Strength Settings, 1 is easy and 4is hard. Switch (SW2) Setting
123456?8

Game Mode OFF Test Mode ON

Coin/Credit4OFF | OFF

1/2 OFF | ON 2/1 ON | OFF FREE oN | ON

Initial PTS. Setting80OFF | OFF | OFF

100 OFF | OFF | ON 150 OFF | ON | OFF 200 orF | ON | ON 250 ON | OFF | OFF 300 ON | OFF | ON 350 on | ON | OFF 400 ON | ON | ON

Bonus PlayBonusOFF

No Bonus ON

Attract MusicNo MusicOFF

LL Music ON

Page 3
  • Test Mode
  • Entering Test Mode

Make sure the main power switch is in the “OFF” position. Set for “Test Mode” by the switching Toggle 1 (SW2) on the game P.C. Board to the “ON” position. Now turn the main power switch to the “ON” position.

  • Memory Test

All ROM and RAM will be tested automatically, and the test result will be displayed on the Video Monitor, with Green meaning “OK”, Red meaning “NG”, and Yellow meaning “NOT IN IC SOCKET”. Also, the memory back-up condition can be tested, and the result will be displayed on the Video Monitor as a Battery illustration. On power up, “BATT” section will be Red. Turn the power off for 5 seconds, then turn back on. “BATT” section will now be Green if good, and still Red if not good. Pressing the Service Switch will step to the next test. (“Switch Test”)

  • Switch Test

All Control Levers, Game Buttons, and Dip Switches can be tested at this time. The screen should show a picture of the control lever and the ‘game buttons, along with the Dip switch. The picture corresponding to the switch being tested will appear GREEN if in the “OFF” position, and RED if in the “ON” position. The Dip Switch setting are shown on the right side of the screen and indicate which switches are ON and/or OFF. Pressing the service switch will step to the next test. (CRT & Sound Test)

Switcn Test

Th LJ i

SL

Page 4
  • CRT and Sound Test
  • CRT Test The test pattern shown in Fig.1 will appear on the screen. This pattern is used for adjusting color convergence. Moving a control lever up or down will change the test pattern to an all white screen shown in Fig. 2. This pattern is used for adjusting color purity. (screen should be pure white.) Moving the control lever again will put the first pattern back on the

screen, if desired.

  • Sound Test *

The different sound circuits can also be tested at this time. Pressing a “B” button or a “1” or “3” button will start a corresponding sound test. To stop the test, press the “A” button or the “2” or “4” button.

oP BALANCE wars, 3A

Fig. 1

  • Return to Game Mode Fig. 2

Turn the main power switch to the “OFF” position. Reset back to “Game _ Mode” by switching Toggle 1 (SW2) on the P.C. Board back to the “OFF” position. Now turn the main power switch to the “ON” position.

Page 5

CAUTION

The suggested factory settings for VS.BASEBALL™ are listed below.

It is recommended that you carefully check the DIP switch settings

prior to operation.

SW1 settings SW2 settings

5 7 off | off off i ee i Ld i Ly Please review the DIP switch label for further information. Nintendo of America Inc.