GTI Club Upright Konami
GTI Club: Rally Cote D'Azur (ver EAA) (Konami, 1996) · Manual · 49 pages · 18 sections · original scan
GTI CLUB UPRIGHT ™
CONTENTS
About this product
Precautions for use
Machine installation
14 Installation ........ceseseesessesseessseesteceesesnesneneeesseeneeseeteneetenesneesenes
1.2 Machine specifications ..
1.3 Service Panel 2.2... --seecseecseccsecceeeeeeeeeesseeeeeeneeeseeneeseeneeneeet
How to play
Networking game machines and PCB settings
3.4 How fo network game MACHINES 0... ecsesssseecsseessseeeeneeeseee
3.2 PCB start-up check (Self test) ooo... eee eseseseseeeesesseeeaesees
3.3 Correcting the positions of steering wheel etc. ...........000
3.4 — Adjusting the game position (manual teSt) ...........::ssecseee
3.6 Mode descriptions
3.6 Network abnormality counter measures
Maintenance and annex
44 Replacing the coin acceptor
4.2 Replacing the fluorescent light... seseseceeeeseecteeeneetee
4.3 Replacing and adjusting the potentiometers ...
4.4 Replacing the gear shift unit SWitCh oe ceeeeeeeeteeteeeeeeee
45 Replacing the timing belt and adjusting the tension
4.6 Adjusting the monitor ...............4.
47 Potentiometer witing information... eeeeeeteeeeeeeeeeee
GTI CLUB UPRIGHT ™
CONTENTS
Page No.
Appendix A Credit board settings 0... cesscessessessseseeesteeeseereteneees 39
Appendix B List of main parts oe ecesssssessessecsessseeseseneeserseensees 41
While the information contained in this manual is given in good faith and was accurate at the time of publication, KONAMI CO. Ltd reserve the right to make changes and alteration without prior notice.
This equipment has been manufactured in accordance with the European Community Directive, and as such bears the CE marking. Any changes or modifications made to this equipment must be in accordance with the European Community Directive. If you make unauthorised changes to this equipment, you contravene the European Community Directive.
Under some conditions of extreme extemal interference, e.g. Radio Transmissions, Electrostatic Discharge or Mains Transients, may cause degradation of performance. However the equipment will recover normal performance once the source of interference has ceased or been removed.
Certain component parts of this equipment are critical to ensure conformance to the European Community Directive, and therefore must only be replaced with parts as those specified.
Si
\ O About this product
Thank you for purchasing this Konami product. This manual explains how to operate your gaming machine correctly.
A Failure to operate the machine correctly could result in malfunction or accidents, so please read this manual carefully before commencing operation. Be sure to operate the machine as described in this manual. Please ensure this manual is always kept with the machine.
- The specifications of this product are subject to change without notice for reasons such as improving the performance
+ The contents of this game, its main data and design are protected by copyright law industrial property law.
+ Unauthorised reproduction of this document or any of its contents is strictly forbidden.
© 1996 KONAMI ALL RIGHTS RESERVED
O Precautions for use
{n this manual, the precautions will be followed without fail in order to prevent damage to persons io install, use or maintain “GTI CLUB™” or other persons or to properties are shown as follows.
Be sure to read the following
+ The following suggestions show the degree of danger and damage caused when the product is used improperly with the suggestions disregarded.
/\ WARNING! Indicates a situation where disregarding the suggestions could result in death or serious injury. J\ CAUTION!
Indicates a situation where disregarding the suggestions could result in injury or product damage
- The following graphic suggestions describe the types of precautions to be followed.
A Indicates a matter of which care should be taken S Indicates a matter which is forbidden &- Indicates a matter which should be performed without fail
+ Setting Up /\ Warning! + Be sure to consult your nearest dealer when setting up, moving or transporting this product. » This product should not be set up, moved or transported by anyone other than industry specialists. Doing so could result in injury or product damage. » When setting up this product, fasten the game machine securely with all the adjusters if the game machine is not fastened securely, injury or accidents could be caused by the machine rocking. » When Setting up this product, take care that no undue force is applied to the connecting sections of the game machine. Failure to do so could cause injury, accidents or product damage.
+ This product is an indoor game machine. Never set up the game machine outside. » Setting up this product outside could result in accidents or equipment failure.
- Do not set up the game machine near emergency exits. » Doing so could block exits in tine of emergency and could result in death or serious injury. Q@
+ Do not set up the game machine: ... ina place exposed to rain or to moisture in a place exposed to direct sunlight in a place exposed to direct heat from air-conditioning and heating equipment etc. near hazardous flammabie substances such as thinners and kerosene on an inclined or uneven floor near fire extinguishing equipment in a place exposed to strong vibration in a place exposed to excessive dust .. Near equipment generating strong magnetism or electric waves! @
+ Do not place containers holding chemicals or water on or near the game machine. » Electric shock or damage could be caused by water or foreign matter entering the inside of the machine.
+ Do not place items near the ventilating holes. » Doing so could cause the intemal temperature to rise excessively, resulting in equipment damage.
- Do not bend the power cord by force or place heavy objects on it. » Doing so could result in electric leakage or fire.
+ Never plug or unplug the power cord with wet hands. » Doing so could result in electric shock.
+ Never unplug by pulling the power cord » Doing so could damage the cord, resulting in electrical leakage or fire. DOOO ©
+ Use an earthing band or similar means of discharging static electricity when adjusting the PCB DIP switches. » lf not discharged, static electricity could damage the electronic components on the board.
" Check wi approval. Th IC guidelines on siting this equipment, All machines should now bear (he CE mark for mark states that all cmussions are within those specified by the regulatory body
- Setting Up A\ Caution!
+ Be sure to use indoor wiring for within the specified voltage range. For extension cord, use indoor wiring of the specified rating or more. » Failure to do so could result in fire or equipment failure.
+ Never plug more than one cord at a time into the electrical receptacle. )
» Doing so could result in fire or electric shock.
+ Do not lay the power cord and the communication cabie where people walk through. You ) may tread or stumble over them. » You may Stumble down and get injured, or damage the cord or cable.
+ Do not place heavy objects on or pull on the pipe connecting the projector unit and drive 8S unit. Also do not use the game machine with the pipe removed and the wiring exposed. » Doing so could result in equipment failure.
+ Make sure the machine has been earthed properly before using the machine. + Clearances of 100mm (3.94in) or more should be created between the game machine and walls.
- Operation L\ Warning!
+ Do not use this product anywhere other than industrial areas. )
» Use in a residential area or an area next to a residential area could affect signal reception of radios, television sets, telephones, etc.
«If there is any abnormality such as smoke, bad smell or abnormal noise being emitted from
the machine, immediately unplug the power cord and stop operating the machine. &
» Using the machine in abnormal conditions could result in fire or accidents
In case of abnormality: 4-Tum off the power 2- Unplug the power cord 3 - Contact your nearest dealer
+ Do not leave the power cord plugged improperly or covered with dust. S
» Doing so could result in electrical shock or fire, so inspect the power cord periodically.
+ Never disassemble, repair or modify any section other than those specified in this manual. S » Doing so could resutt in fire, malfunction or equipment failure.
- Operation M\ Caution!
+ The following users should not play the game: » Doing so could cause accidents or illness. S
+ Those under the influence of alcoho! * Those suffering from or being treated for arm or wrist ailments
+ Do not plug or unplug the power cord with wet hands. » Doing so could result in electric shock.
+ When handling the power cord, take care of the following: » Improper handling could result in fire or electric shock.
+ Do not damage the power cord + Do not modify the power cord + Do not bend the power cord excessively + Do not twist the power cord + Do not heat the power cord + Do not pull the power cord + Do not bind the power cord + Do not tread on the power cord + Do not sandwich the power cord + Do not drive a nail into the power cord. ©
iS)
+ If the power cord or power plug becomes damaged, stop using the machine immediately. » Using a damaged power cord or power plug could result in fire or electrical shock.
+ Do not place items or heavy loads on or provide a strong impact to the moulding. » Doing so could cause the object on the machine to fall off or could damage the machine, resulting in injury.
« Inspection and cleaning ‘A Warning!
- Be sure to tum off the power and unplug the power cord from the receptacle before inspecting or cleaning the machine. » Failure to do so could result in electrical shock.
+ When replacing parts, be sure to use parts of the correct specifications. Never use parts other than the specified ones. » Using improper parts could result in fire or equipment failure.
+ Never disassemble, repair or modify any section other than those specified in this manual. » Doing so could result in fire, malfunction or equipment failure.
- To clean the game machine, wipe it with a soft cloth dampened in a neutral detergent and wrung out. » Using organic solvents such as thinners may corrode the materials. » Electrical shock or equipment failure could be caused by water entering the inside of the machine. QO @
« Moving and Transportation M\ Caution!
+ The game machine contains electronic and precision components which are sensitive to S vibration and impact. Great care therefore should be taken when moving and transporting the game machine. Be sure not to let the machine tip over.
+ Fully raise all the adjusters before moving the game machine and move it utilising the & casters. Be sure to tum off the power and unplug the power cord from the receptacles before a moving the game machine. » Failure to do so could result in accidents, damage or equipment failure.
! Precautions in Handling !
+ When setting up, handling, inspecting, maintaining, moving or transporting this product, follow the procedures and instructions set forth in this manual and perform such work safely.
+ Do not remove labels of * Warming *, “ Caution “, etc. attached to the product.
+ Do not set up, handle, maintain, move or transport this product under conditions specified in any of the previous sections.
« If a new owner is to have this product as a result of transfer, etc. be sure to give this manual to the new owner.
1.1. Machine Installation
The machine is supplied fully assembled but it is recommended that the following checks are carried out prior to power-up:
- Remove the back door of the unit ensuring that all conneciors are firmly in place.
- Remove the installation kit, containing manuals and spare parts, and store ina safe place.
- Ensure all mechanical connections are secure.
- If you wish to link machines, read the networking information in section 3.1
- The machine is now ready to power up.
1.2 Machine Specification
Dimensions: 72. cm x 98 cm x 193 cm
Weight: 170 kg
Voltage: 230 V A.C.
Frequency: 50 Hz
Power: 300 W
1.3 Service Panel
You will find the service panel when the maintenance door is opened with the attached maintenance key.
Figure 4 Service Panel Detail
2 How to play
This machine simulates a driving game in which eight small rally cars ( one of which is to be selected by the player and the other rival cars ) compete againsi each other through a virtual urban area, as if the player is racing through a beautiful resort town in southern France. This machine allows the player to enjoy a thrilling driving game while controlling his car, complete with realistic “quick tum" & “ drift driving “ using the handbrake lever. The machine can also be linked up to a maximum of 4 networks, increasing the realism and enjoyment for the player.
+ How to play
- Insert a coin into the slot to start the game. (In free play mode push the VIEW SHIFT button io start the game ).
- The Network Entry Screen appears. If a coin is put in another machine which is connected this machine through the network, during this period, the network race starts automatically. @ If the machine is not connected to the network or it is impossible for the player to play because someone else is playing the game, proceed to the operation in the following item 3 after a coin is inserted
- Select the player car on the Machine Select Screen. Select desired car by turning the steering wheel and the stepping on the accelerator.
- The screen changes to the Game Select Screen. Then, make the game mode selection from the following modes. Select the desired mode by turning the steering wheel and stepping on the accelerator. > Beginners Mode .... A part of the urban area in the map of entire courses is made into a circuit, where the player plays a circuit race. ..-All the roads are made open, and the player plays circuit race whilst looking for the shortest and fastest route. This mode is for an expert player. « Super - Advanced mode ....... The player plays the circuit race in the reverse course to that of advanced mode. This mode is for a super-expert player who wants to challenge an extremely difficult course where a labyrinth of roads is running. ... This mode can only be selected when in network play. The player can enjoy a car racing “ Tag “ in a closed urban area.
- When the selection from the above modes is over, the game starts. The game begins when the countdown has ended on the screen.
- The basic control is performed by the following equipment: + Steering wheel ....., Running direction can be controlled by turning the wheel right or left. .. Depressing the pedal accelerates and releasing the pedal decelerates the car speed. Depressing the pedal brakes the car. When it is pulled up, the rear wheels are locked and skidding for “ Quick Turn “ + Advanced mode .........e+0
+ Special mode
+ Accelerator
+ Shift Operation ...................... Manual operation (MT) or automatic operation (AT) can be selected. Switching over to MT or AT can be
performed by pressing the button at any time during
play. + View Shift... eee Pressing the VIEW SHIFT button enables the player to select three different kinds of view, at any time during play- Rear View / Distant View / Driver's View In special mode, the “ Super Distant View “ is exclusively set and the player can not select any other views than this.
- The rules for each mode are as follows. + Beginner's / Advanced / Super-advanced modes The remaining play time is added whenever the player's car passes each check point in the course. The game ends either when the player's car has run the whole pre-set course or when the play time is up. The ranking, entire route travelled and the point reached at that time are displayed on the map when the game is over. When the player's car has run the whole distance in the race, the entire route travelled by the player's car is replayed on the screen, and the ranking, total lap time and course record are displayed. Name entry is possible only when the player has renewed the course record. « Special mode A“ Bomb Mark “ is attached to only one of the participant cars, which becomes the “tagger in tag. When the “tagger” bumps any one of the competitors cars, the “ Bomb Mark “ is handed over to the bumped car. The player who has the “ Bomb Mark “ on his car at the time when the limited time is up loses the game.
¢ Buy in during game
In GT] CLUB™, no buy in is allowed.
« Player car
One “ Player's Car “ can be selected out of the total five cars including four smail cars and premium car (Super car). There is no difference in performance among the small cars, but the premium car has greater acceleration performance. The play fee may be set higher only for the premium car.
« Rival cars
The “ Rival Cars “ are composed of the small cars which have not been selected ( except the premium car ) and an additional four rival cars.
3 Networking game machines and PCB settings
3.1. How to network the game machines
The specification of GTI CLUB™ aliows up to four game machines to connected so that players can enjoy ‘versus' games. To network, connect the networking cord supplied with each game machine to the network pin jack of the projector unit after setting up the game machines (see previous section).
A
- When using the game machine independently, do not connect anything to the pin jack. + Game machines are linked together in a chain with the network cords. Do not connect anything to the first and last pin jacks in the chain
- When networking game machines, set the PCB main board dip switch “network ID” while referring to “DIP SWITCH SETTINGS" on page 15
+ Networking four machines
Player 1 Player 2 Player 3 Player 4 oe} (ee) (ee) Lee
Do not connect anything to the pin jacks at the both ends of the first and last machines
3.2 PCB start-up check (self test)
+ When the power switch is turned ON after the installation of the machine, the performance of the PCB is checked automatically. The result is displayed on the screen.
- Be sure to perform the self test before using the machine. If an abnomnality persists or the machine does not operate property, turn OFF the power switch immediately to stop operating the machine
+ Result of Test
If test is OK, + The position of steering wheel is corrected automatically.
If any abnormality is detected, “BAD” appears on the screen, and the checking is repeated. If “24G BAD" is displayed, once tum OFF the power switch and then turn it ON again whilst depressing the test switch button on the service panel. The content of setting in manual test and the course record return to those having been set at the time of shipment.
After the machine is installed, or PCB is repaired or replaced, once retum the content of setting to those having been set at the time of shipment by tuming ON the power switch while depressing the test switch of the service panel. If the abnormality indication still appears or the machine does not operate normally, tum OFF the power switch immediately to stop operating the machine.
3.3
on
on
on Correcting the positions of the steering wheel etc.
+ After the self test, the positions of ihe following equipment are corrected automatically - Steering Wheel / Hand Brake / Accelerator / Brake At this time, the message “DO NOT TOUCH THE CONTROL DEVICE WHEN THE MACHINE IS BEING INITIALISED. “ appears on the screen. Refrain from touching the steering wheel, handbrake, accelerator or brake as long as this message appears. The steering wheel turns a few times to the left or right automatically.
+ Result of position check
If the result is OK, + When the position check is over, the operation mode returns automatically to the game mode.
if the result is abnormal
The result of check is displayed as follows on the screen.
+ Steering wheel abnormal, the message “ Device Error (STEERING WHEEL) “ appears on the screen. What to do The steering whee! contro! exceeds the correctable range or the steering wheel reaction device is out of order. Make the adjustable by referring to “4.3 Adjusting the potentiometer “ on pages 33 & 34
+ Hand brake abnormal, the message “ Device Error (HAND BRAKE) “ appears on the screen . What to do The hand brake control exceeds the correctable range. Make the adjustment by referring to “4.3 Adjusting the potentiometer “ pages 37, 38 & 39
+ Accelerator abnormal, the message “ Device Error (ACCEL) “ appears on the screen.
What to do The accelerator control exceeds the correctable range. Make the adjustment by referring to “4.3 Adjusting the potentiometer “ pages 35 & 36
+ Brake abnormal, the message “ Device Error (BRAKE) “ appears on the screen.
What to do The accelerator contro! exceeds the correctable range. Make the adjustment by referring to “4.3 Adjusting the potentiometer “ pages 35 & 36
When any of the above signs appear, push the test switch on the service panel to go to the manual test mode. Then choose “\/O CHECK" to check the device which shows the error. In case the DEVICE ERROR is still displayed after the readjustment, there may be something wrong with it. Turn the power off immediately.
ifthe “ GAME MODE “ is selected on the “ MAIN MENU “ screen, whilst the controls are in a faulty condition, the game will not play properly.
If an error sign is displayed, or the device doesn't work correctly turn off the power switch immediately.
3.4 Adjusting the game environment (manual test)
Manually check and change the settings for the screen display and game contents.
- To start the manual test mode
- Tum on power switch
- Press the test switch on the service panel during the game demo mode.” If you are working with networked machines, you must have all four machines in demo mode before the test switch will take effect.
- The unit is now in the manual test mode and the main menu is displayed on screen.
- To quit the manual test mode
- Choose the “ GAME MODE * from the main menu using the shift lever.
- Push the “ VIEW “ shift switch.
The game then retums to normal game mode.
MAIN MENU
VO CHECK SCREEN CHECK COLOR CHECK MASK ROM CHECK NETWORK CHECK DIP SWITCH CHECK C.G. BOARD CHECK SOUND OPTIONS GAME OPTIONS COIN OPTIONS NETWORKING CONFIGURATION,
GEAR SHIFT UP/DOWN
- Selecting each mode
How to select each mode from menu
Select =>
Set => ECT ITEM + PUSH VIEW SHIFT SWITCH = DO CHECK
Push the VIEW shift switch
- Check each controller, page 18 ~ Adjust screen distortion, page 19 ~ Adjust color, page 19 ~ Check mask ROM, page 19 > Check network, page 20 ~ Set DIP switches, page 22 + Check CG board functions, page 22 ~ Adjust sound volume, etc, page 23
- Set difficulty etc., page 23
Move the shift lever up or down
After selecting a mode, refer to the page on which that mode is described in details.
? Turning ON the power whilst depressing the test switch will return all manual settings to their factory preset setting. s
3.5 Mode descriptions
+ The original factory settings are displayed in green; the changed settings are displayed in red. + After completion of the setting change, select “SAVE AND EXIT “ and push the VIEW shift switch. Then , the settings are saved automatically and the screen returns to the main menu. + If “EXIT "is selected after the completion of setting change, the following message appear:- “YOU DID NOT SAVE. DO YOU WANT TO SAVE? YES/NO “ + If “ YES “is selected, the message * NOW SAVING “ will appear, the changed settings will be saved and you will be retumed to the main menu. + If “NO “is selected, the message “ NO MODIFICATION * will appear and the changed settings will not be saved. will
If “ FACTORY SETTINGS" is selected and the VIEW shift switch is pressed, all settings will return to the original settings that have been made at the time of shipment. the
«0 HO CHECK.
+ The check mode for the controls.
To return to the main menu screen, move up the gear shift lever while pushing the VIEW shift switch.
VO CHECK
| ‘Shows the value for the | VIEW SHIFT SWITCH OFF | COIN MECH SWITCH OFF |
steering wheel in decimal GEAR SHIFT SWITCH-- __ SERVICE SWITCH OFF
| (HEX) | \ | ATIMT SHIFT SWITCH OFF | TEST SWITCH OFF |
‘Shows the value for the left centre right Hand brake in decimal STEERING WHEEL \X The marker position changes to
| (HEX) | ene | 00000 (00000) | show the input value. |
HAND BRAKE 00000 (00000) Shows the value for the ACCEL Accelerator Pedal C
| decimal (HEX) | n | 4 | BRAKE I | 4 | Check the steering wheel reaction |
00000 (00000) device. The steering wheel tums
| s | / | : | automatically clockwise and |
Boe taal mee HOLD VIEW SHIFT SWITCH & GEAR SHIFT DOWN = ~ Walsine teas aaa : ACTIVE STEERING WHEEL TEST and the meter value changes durin: HOLD VIEW SHIFT SWITCH & GEAR SHIFT UP = EXIT test procedure. Do not touch the steering wheel during this proce
+ If the steering wheel or the accelerator is not properly adjusted, make the necessary adjustments while referring to “ 4.3 Replacing and adjusting the potentiometer “ on pages 33 to 39
+ Adjust the focus, distortion of the screen while watching the grill on the screen. Use projector control PCB (See page 46.) to make the adjustment. To retum to the main menu, push the VIEW shift switch
--eColorCheck. . . . .
+ Make the adjustment using the projector control PCB (mounted behind the access plate ‘on the projector unit), so that the colours of the colour bar should be displayed in discrete gradation. To retum to the main menu, push the VIEW shift switch.
¢ Mask ROM check :
+ Mask ROMs are checked one by one, and when no abnormality is found, “OK “is displayed. If any abnormality if found, “ BAD * is displayed. To start checking, push the AT /MT shift switch. To return to the main menu, push the VIEW shift switch.
+ Tum ail machines that are connected with the network cables to this mode, observe the screen for at least one minute. The machines should satisfy the following three conditions.
To retum to the main menu, push the VIEW shift switch.
A + If any of the three conditions are incorrect, it indicates possible communication malfunction. Take measures while referring to “ 3.6 Network abnormality counter measures “ on page 26. If the same symptom persists in spite of taking measures or a problem occurs that is not covered by this manual, tum off the power switch immediately and do not operate the machine.
+ Network Check screen
NETWORK CHECK ‘Shows the * Network ID “ of the connected game : : machine, (1-4) This BOARD-ID Is 3
ERROR DOWN STATUS
| 1D No.1 | 0 | 0 | DNC | * DNG * (did not connect) appears if network |
| ID No.2 | QO | ty | ONC | connection is not made |
| 1D No.3 | 0 | 0 | | | . |
| ID No.4 | 0 | 0 | DNC |
PUSH VIEW SHIFT SWITCH = EXIT
+ Check Items
Check that the “ | * mark in the STATUS column is moving from the left to the right at fixed speed
¥ Check that the value in the ERROR column is below “ 10 * after one minute
Check that the value in the DOWN column does not change from “ 0 “
- Screen display when game machines are networked
+ Two game machines are networked
Screen for player 1
+ Four game machines are networked
Screen for
Screen for player 3 NETWORK GHECK
-+ “This BOARD-IDis3 -_ : 5 ERROR . DOWN STATUS IDNot 2.0 Oe ft MDNO2 2: 0.57 07 INOS. -O. - O. IDNo4 0 o 4
PUSH VIEW SHIFT: SWITCH = EXIT
Screen for player 2
- "This BOARD-D is 2
ERROR DOWN STATus- IDNot.....0... 0
| IDNo2 | 0 | "O°" | | |
| IDNo3, | 0 | 0 | DNC |
| swlDNO4.. | 8 O.2° | 0» | DNG |
PUSH VIEW SHIFT SWITCH = EXIT
Screen for player 2 NETWORK CHECK
his BOARD-ID is 2
El ROF DOWN STATUS - Oe Oye s |
| ~ | 0 | | |
| Oo. | 0 | i] |
Screen for player 4 NETWORK CHECK
This BOARD-D is 4
2 ERROR DOWN STATUS
| ID No.4 | 0 | 0 | : |
| ID No.2 | 0. | 0 | |
| 1D No.3 | 0 | o | |
| IDNo.4. | ..0 | 0 | i} |
¢ DIP Switch Settings
+ The DIP switch setting mode
When changing the dip switch settings, set the DIP switch by referring to the chart below. To retum to the main menu, push the VIEW shift switch.
« Be sure to tum OFF the power switch before setting the DIP switch + Generation of static electricity may cause breakage of electronic parts on the PCB. Be sure to eliminate static electricity by means of the earthing band.
+ DIP switch setting chart
+ Main board ( upper PCB ) DIP switch + Set all the DIP switches on the CG board to OFF SETTING First machine NETWORK ID _| Second machine Thitd machine Fourth machine Not in use ( Be sure to set it OFF.
+ When setting DIP switch of networking game machines, number each switch in the sequence of the small number (Eg. When networking two game machines, set the network ID of the one machine to 1 and the other to 2.)
- The DIP switch on the PCB can be shifted easily by utilising a thin flatblade screwdriver or a ball point pen.
+ CG Board Check
- The CG board function check mode. Observe the screen in this mode to check whether the CG board Is functioning correctly. To retum to the main menu, push the VIEW shift switch
Two toruses (doughnut-shape bodies) are rotating
Two “A&B Product" logos displayed in front of the torusus are flickering altemating.
Two backgrounds are displayed at the back of the rotating toruses.
+ The following screen appears when this mode is selected
Turns the demo sound On or OFF + ALL THE TIME - Sound always ON pore + ONCE EVERY 4 CYCLES - Sound ON every 4 cycles
| ‘Sound Volume | oa | ie | ; | + COMPLETELY OFF - Sound always off |
GoonoonosR000000000Rnn0.. .:20
| ; | Pas | ESR | a | . | Adjusts the volume from 0 (min) to 30 (max) |
Sound Scale Check
| ay | Seg | ith | Serre | pear | ‘You will hear a do-re-mi musical scale from the left then the |
| GM. in | GAME MODE ON’. | . | fight speaker, this is repeated twice. |
Tums the BGM during the game ON or OFF
| ; | = | . | Reiums all the settings to the factory settings at the time |
GEAR SHIFT.UP/ DOWN of shipment PUSH VIEW-SHIFT.SWI
+ The following screen appears when this mode is selected.
+ When connecting the machines to the network communication, be sure to set all the PCBs to the same configuration. Time limits of special modes: 100, 120, 140, 160, 180, 200, 220, 240 GAME OPTIONS
| aa | > | Hoar | Re | we | : | Difficulty Level settings |
| Tag Game | woe | 480 counts | “ | . | EASIEST @ HARDEST | |
| as! | Io | “Difficulty Level | -.,:.” | Number of Laps | ||
| ‘Normal race | 41 | Medium , | “3 |
Hard Race“ 2... *.4/- Medium’. Very Hard race. 4/-Medium Sets circulation frequency (2, 3, 4 times) Sets Force of Steering wheel reaction device a LIGHT <> VERY HEAVY Motot Power Level ‘Switches the speedometer display KM/H or MPH "Speed Meter Display"? - «
| ‘Game Joining Period : | i | 7 | —~ | 4, 8, 12, 16 seconds |
| Course Record Saving | -.\"--"-- | Enable = | nt | |
| Bonus credit for Winner. | ;-", “Disables: | ° | \ | Record the course record. When * Disabled * is |
| FACTORY SETTINGS | - | : | selected, the course record is not recorded nor | |
| SAVE and EXIT | cree | . | initialised, | |
| EXIT | wan | cee | ; | 'y |
| i | ants | = | 2 | When * Enable “ is selected. 4 credit is added to |
| "GEAR SHIFT-UP/ DOWN: | ELECT.OPTIONS | the top ranking machine in the network. |
_PUSH MIEW.SHIFT SWITCH. ODIFY. SETTING
+ If the setting of circulation frequency for a course is changed and saved the course record is reinitialised
“ «Coin Options -
+ The following screen appears when this mode is selected.
COIN OPTIONS ‘Always keep eet to INDEPENDENT
Free Play No Sets the relation between the number of coins and
Mechanism INDEPENDENT Menunberot rods: Coin Slots 2Coins, 4 Cr Premium Start Credit” “ —— pod cin poling nal coins for the selection of the FACTORY SETTINGS : SAVE and EXIT , Poa a \____ Retums all the settings to the factory settings at time of EXIT : shipment. GEAR SHIFT UP/DOWN | =SELECT OPTION
PUSH VIEW SHIFT SWITCH MODIFY SETTING
+ The relationship between the number of coins and the number of credits
setting | 1[2] 3/4 75 [6 [7] a] 9 [10/11] 12113 [14715] 16]
letworking Configuration -
This mode automatically unifies the remaining machines in the network.
Setting ——_—_—_—— Auto Setting u u u g
Player 1 Player 2 Player 3 Player 4
+ Setting modes which can be unified are as follows:
“SOUND OPTIONS “See page 23 “GAME OPTIONS “ See page 23 “COIN OPTIONS“ See page 24
+ How to unify the settings
- Since the machine modes are unified in network communication function, check whether the network communication is working correctly, using the “ Network Check * mode.
- All the machines which are connected to the network are displayed on the “ Main Menu “ screen for the manual test.
- Set “ Sound Options ", “ Game Options * & “ Coin Options “ on just one of the machines in the network.
- When the setting has finished, select the “ Network Configuration “ from the * Main Menu “ screen, on the one machine that has just been set in action 3. Push VIEW shift switch 5, Make sure that other machines connected to the network have entered into the “ Network Configuration “ mode.
- The game is started automatically when the AT/MT shift switch Is pushed. if the VIEW shift switch is pushed at this time, the screen retums to the “ Main Menu “
- When the network communication setting is over, the screen retums automatically to the “Main Menu *.
+ If the network communication setting has not been made normally by the above steps 5 to 7, make the same setting by manually operating the individual machines.
3.6 Network abnormality counter measures.
If the “ NETWORK ERROR " message appears, or if any item responds incorrectly in the network communication check described on pages 20 & 21, or the projector displays differ from the specified ones, take the following measures.
A + If the same symptom persists in spite of taking measures or a problem not covered by this manual occurs, immediately tum off the power and do not operate the machine.
Symptom 1. The “NETWORK ERROR “ message appears on the screen after the power is tumed on.
NETWORK ERROR ‘Shows the “ Network ID * of the game machine (1 to 4) CHECK PLAYER MACHINE NUMBER. IN THE NETWORK OR CHECK NETWORK CABLES
THIS MACHINE'S CAR No. 1
+ Possible causes and measures to be taken
Possible causes [Measures + The main DIP switch “ Network ID “ + Set DIP switches properly settings are improper + One of the networking cables has + Properly connect the network cables and become disconnected form the machine make sure the pins are free from dirt & dust + A network cable is connected between + Disconnect the network cable from those the pin jacks of the first and last machines _| pin jacks
Symptom 2. The * NETWORK ERROR “ message appears on the screen during playing
‘NETWORK ERROR’
CALL THE CLARK
- Possible causes and measures to be taken
Possible causes Measures + One of the networking cords has been +1. Turn OFF the power disconnected during play 2. Re - connect the network cord
L 3. Turn ON the power
+ One the networking cords has been + Replace the networking cord with the damaged and could be broken internally spare network cord supplied.” + The test switch (on the service panel) of | + 1. Turn OFF the power one of the networked machines has been 2. Close the maintenance door ushed 3. Tum ON the power + Any of the machines which are + Enter the manual test mode and set the connected through the network have same game options among all the different game option settings. (In manual | machines.
"You can slea use commicrcaiis sald ideo cabhe ¢ 780 3C-PV having a loneth of nor less
4 Maintenance and annex
4.1 Replacing the coin acceptor
+ Be sure to tum off the power switch and remove the power cord plug from the receptacle before replacing the coin selector.
1. Open the maintenance door.
2. Locate the coin acceptor as shown.
3. Remove the 10way IDC connector as illustrated. Please take care to only apply force to the connector and not the grey ribbon cable.
4. Locate the retaining bar clip as shown This secures the retaining bar, holding the acceptor into the coin bracket.
5. Lift the clip ‘clockwise’ about its pivot. This will release the retaining bar.
6. Remove the retaining bar, freeing the coin acceptor.
ra Push the coin acceptor sideways to release it from its holding bracket. Take care not to apply unnecessary force when trying to free the acceptor.
8. Re-assemble with new acceptor in reverse order.
4.2 Replacing the fluorescent light
+ Be sure to turn off the power switch and remove power cord before replacing the fluorescent light. « The fluorescent light will be hot after use. Wait until it cools before replacing the unit with a newer one. + Always exercise extreme caution when operating on mains wiring, ensure the power is disconnected before carrying out this procedure.
1. Remove the fixing screws from the topside of the light unit.
2. Slide the front perspex down, to gain access to the fluorescent tube.
3. Remove the sockets on either end of the fluorescent tube by sliding them off. The tube can then be removed from the retaining clips.
If the starter needs replacing, replace it with one of a similar type.
4. Assembly is the reverse of the above procedure
4.3 Replacing and adjusting the potentiometer
A
- Be sure to turn OFF the power switch and remove the power cord plug from the receptacle before replacing the potentiometer
1. Loosen the fixing screws on the shaft of the steering assembly. If these screws are not easily accessible, tum the steering wheel.
2. Remove the hexagon nut fastening the potentiometer to the bracket.
3. Attach a new potentiometer to the fixing bracket
4. De-solder the wiring from the faulty potentiometer and solder it to the replacement. See page 49
7. Check the wiring, before commencing further.
8. Using a flat blade screwdriver, adjust the potentiometer shaft as shown.
9. Mount the bracket on the main assembly using the 2 fixing screws.
10. Tighten the grub screw on the steering shaft.
11. Carry out the test procedure as described in “ 3.2 PCB Start up check (self test) “on page 15
30,
+ How to replace the pedal unit potentiometers
- Be Sure to turn off the power switch and remove the power cord plug from the receptacle before replacing the potentiometers
Remove the lower maintenance door from the = Ss rear of the unit.
2. Disconnect the pedal loom from the main loom.
3. Remove the fixing nuts and earth via the rear of the unit, then remove the pedal assembly from the front of the unit.
3. Loosen the grub screws on the potentiometer shafts and remove both gears.
4. Remove the hexagon nut fastening the potentiometer to the pedal assembly.
« How to adjust the pedal unit potentiometers
5. Attach a new potentiometer to the pedal assembly.
6. Desolder the loom from the faulty potentiometer and resolder it to the replacement. See page 49
7. Replace the gear on the potentiometer shaft, do not tighten the grub screw.
8. Without moving the pedal, adjust the potentiometer with a flat blade screwdriver.
Adjustment Method
+ Accelerator - Fully tum the potentiometer counter clockwise and then tum it back by jabout 10°
« Brake - Fully turn the potentiometer clockwise land then turn it back by about 10°
9. When the potentiometers have been carefully adjusted, tighten the grub screws on the gear shaft.
10. Make sure all fixings are secure and replace the maintenance door.
411. Figure 1 Brake Potentiometer setting
Figure 2 Accelerator potentiometer setting
Carry out the procedure described in “3.2 PCB Start-up check (self test) “ on page 15
+ How to replace the hand brake potentiometer
« Be sure to turn OFF the power switch and puil out the power plug before replacing the control.
- Since the hand brake is heavy, use due care when handling it.
1. Remove the front play panel, disconnecting the loom and earth link in the process.
2. Replace the potentiometer as per the instructions for the pedal unit.
4.4 Replacing the gear shift unit switch
- How to replace the gear shift unit microswitch
+ Be sure to turn off the power switch and remove the power cord plug from the teceptacie before replacing the potentiometers
1. Remove the play panel assembly, taking care to disconnect the wiring loom and earth wire.
2. Remove the 4 screws fastening the gear shift unit and take out the assembly.
3. Disconnect the loom connector from the main loom. Determine which is the faulty microswitch and remove it.
4. Desalder the wiring from the faulty microswitch and resolder it to the replacement.
5. When installing an new microswitch, take care to ensure the microswitch is positioned correctly.
Use the following as a guide:
4.5 Replacing and adjusting the timing belt
+ How to replace the timing belt
- Be sure to turn OFF the power switch and remove the power cord plug from the receptacle before replacing the potentiometers
1. Remove the play panel from the unit as described in section 4.4
2. Loosen the 3 motor bracket fixing screws and the adjuster bolts and remove the timing belt.
- How to adjust the timing belt
4. Loasen the 3 motor bracket fixing screws and adjust the timing belt tension by turning the adjuster bolt.
The sag of the belt should be 1.6mm for a weight 0.SKq
Figure 3 Timing belt sag
4.6 Adjusting the monitor
+ The monitor has already been adjusted at the time of shipment, but it may be readjusted as desired.
- The interior of the monitor contains high voltage electricity, so take great care not to touch it
« Monitor Adjustment PCB
The monitor adjustment PCB is located inside the monitor maintenance door of the main unit. ( Loosen the 6 screws and remove panel )
4.7 Potentiometer wiring information
When replacing the potentiometers in the game machine pay attention to the following colour codes used.
Potentiometer 1 3
Steering BLACK? PINK BLACK
Acoslerator PIAKTELUE PARRTELUE Hand Brake PINK/BLAGK BLACK/GREEN
When soldering the potentiometers the following points should be observed:
1. Excess heat can damage the potentiometer.
All wiring should be insulated using silicone sleeving or heatshrink tube.
Check all joinis that have been made, they should appear shiny and have a good mechanical bond with both surfaces,
Poor soldering can cause intermittent faults with the controls, if in doubt leave any repairs to an appropriately skilled operative.
Appendix A - Coin settings
+ The credit board settings need to be changed in accordance with the currency of each country.
Set dil switches (DIL 1) sw-1 to sw-5 according to the options found in the relevant price of play table on the following pages. Set dil switches (DIL 2) sw-1 to sw-4, which are located under the IC socket as shown in the table below. Sw-4 must always be set to ‘off’ as the game board only operates in common mode. Care must be taken when removing the IC from its socket so as not to damage its leadout pins. After setting the switches replace the IC in its socket with the package ident mark adjacent to the board edge.
A + Be sure to turn the power OFF before setting the DIP switches.
- The position of the coin selector DIP switches.
The coin selector DIP switches are provided inside the maintenance door. See page 10
- Setting DIP switches 2
ba COIN SETTINGS
OFF OFF OFF ON UK ONLY 100 50 20 10 200 COIN
- Setting DIP switches 1
Playsettings for UK Kling V3.4 UNITED KINGDOM i Coin 4 Coin 3 Coin 2 Coin Coins Credits given against coin input 10 2 50 100 200 | Dipswit Per game 1.00 2.00 500 {| 10.00 20.00 Std oTotolofo 4.00 {2.00 6.00 12.00 24.00 Bonus [1 {ofololo 0.50 4.00 ~F 2.50 5.00 1) o0fclo 0.50 1.00 3.00 7.00 1{ofotlo 033 0.67 1.67 3.33 oli{elto 0.33 087 | 2.00 5.00 ofitolo 0.25 0.50 1.25 2.50 1{afof{o 0.25 0.50. 125 | 3.00 i i}tajyofe 0.20 0.40 1.00 2.00 ul ofofott}o 0.20 0.40 1.00 2.00 5.00 Bonus | 1 |/a{/o{1]0 0.17 0.33 0.63 187 _{ 333 Std oliloli}o {0.17 033 0.83 1.67 4.00 Bonus | 1{1/ol1]o} 0.42 0.20 0.63 1.25 2.50 Std ojots{ri{o 0.40 020 0.50 1.00 2,00 Std 1{o[t[i1}o 0.10 0.20 0.50 1.00 | 3.00 Bonus | ofti1{i1ilo0 0.08 0.13 0.42 0.63 1.67 Std 1fait{[tfo 0.07 10.10 0.33 0.67 138 : Std ofofojoii 200 0.05 0.08 0.25 0.50 1.00 Std +fotofoli 280 0,04 0.07 {020 0.40 0.60 Sid ota] of ol 300 (0.03 0.06 0.17 0.33 0.67 Sid 1 [1 f ofo{4 350 | 0,03 0.05 0.14 0.25 067 sid |o{o{i{o| 400 (0.03 0.04 0.13 0.25 0.50 Std 1{/ol1]oj1 450 {0.02 0.04 on 0.22 0.44 Std o[1+frtola 500 0.02 0.04 0.10 020 0.40 Sid ee
Appendix B - List of main parts
+ Replacement part numbers
Part name Part code | Quantity
| Monitor surround vac-form | __—'|: 541846 | | | 1 | [ |
| Monitor - Wells Gardner | 10204 | 1 | ||
| Mains Filter | 80084 | 4 | ||
| Steering Unit Assembly | 381845 | 1 | ||
| Steering wheel | 21244 | 4 | ||
| Gear Shift Unit Assembly | 31665 | 4 | ||
| Pedal Unit Assembly | 381967 | 1 | ||
| Handbrake Unit Assembly | 381966 | 1 | ||
| PCB (Main) | 11334 | 1 | ||
| Coin Acceptor Door and Coinbox_| | 50609 | 1 |
Door (1 item) | Coin Box 4
| Coin Selector | [_s0661 | 1 | UK version | |
| 13 | Coin Counter | | 50003. | 1 | 42v Meter | |
| 14 | Service Panel switch | A5A020 | 2 | ||
| 15 _| Switch Mode PSU | 14034 | 1 | Sv Logic Supply | | |
| 16_| | Switch Mode PSU | 14032 | 1 | T2v Logic Supply |
| 17_| | Switch Mode PSU | 1 | 12v Motor Supply |
PCB (Steering) 1 Speaker 2
| 20 _{ View shift switch | 22479 | 4 |
| AT/MT switch | 22487 | 1 |
ASA001
| 24__| | Mains Power Cord | 162189 |
+ Steering Assembly - Part No : 381845
- Timing Belt
1, Motor 12. Steering gear
- Steering Base 3. Potentiometer
- Motor gear
- Motor Support —— Bracket
Part name 51032 4
42100 | 4 [Timing Beit 3t63 [203634 jo
31663 [a | 5 |SteeringBaseSSCSCSC*di:«C03634 a ee | 6 | Steering wheel Shatt__— 203638 |_7 | Motor Support Bracket___ [203635 | 8 | Steering SupportBracket_ | 203639 | tT | 9 {Potentiometer Bracket | 203834 PT | 10 |ShaftStopper Satg7d aT | 14 [ShaftCam 203642 TT | 42 [SteeringGear aOR |_13 [MotorGear 3703
- Handbrake Assembly - Part No: 381966
Part name Remarks Handbrake Bracket 2__| Handbrake Block Potentiometer Coil Spring 41 : Grip 542098 Pot 31652 1 Fits onto shaft cam.
| 9 | Stopper 541878 4 | 10_| Hand Brake Lever __| 204028 es 31651 1 Fits on potentiometer
Quantity
No.
+ Pedal Assembly - Part No: 381967 4, Suspension Spring.
- Pedal Stopper
- Gear quad
- Potentiometer
- Gear C
No. Part name Part code | Quantity Remarks
| 1 | Pedal Stopper | $44878 | 2 | |
| 2 | Gearc | 31651 | 2 | Fits on potentiometer | |
| 3 | Gear Quad | 31652 | 2 | Fits on pedal asm. |
| 4__|{ | Suspension spring _ | 31653 | 2 | |
| 5 _[ Potentiometer | 42100 | 2 |
MONITOR PLE
J Hs ALARM. 9 SUPPLY 2 a PWM Sv PWM CONT POSS b x a df sg ot rb ek? CQO” PLS
PWM OUT
ALARM DOOR SW.
Pos2
PEDALS PL2
B SW1 SERV sw
© SW2 TEST SW
Posi eeu METER CASE AUDIO PL17
POSS FAN
VIDEO
PL16, PWM INTERFACE
PLIS
ROUTING
COLOUR
BULK
Peay see} SHIFT bom | Perr 7eRn AUTO Sore [1a\o.8 GRe0 | SERV Stoner ULSRAKE SToNAC take a | So cee stensL iss Pee Sa-oxo | SEoT \o. a STEER = PEDAL SNS Yara
BLIe-1 BLie-2 PLie-3 [73\o-3 BWM CONTROL BHM CONTROL a [pw CONTROL | PLia-4 [ PL12-5] PLia-6 So L13\o-a [pw CONTROL 1135 Zvio | eh SONTROL {TSNo. a ROUTING
COLOUR FUNCTION GAUGE)
| GRNZREI | ACARMSTONAL | T3702 |
| GRNZORG | ALARM _STONA\ | 1320-2 |
BLUZWHT. ARMING Sw 1370-2.
| BLUZORG | ARMING SH ONO | 1370 |
| BL | METER SINE | 1370-2, |
| REO | +igy METER | 1370.2 |
‘ORG +12v MECH CAMB [7i3/0-2
| WHT | GND _MECH LAMP” | 13/0.2 |
| PL7=11 REO/BLU | MOTOR _O/P + | 24/0.2 |
| PiL7=12 mrss BLU | MOTOR O7P = | 2470.2 |
| BL1-9 — oRG/BLU | +1 3y PRM Boe | 2479 |
| PL1=19_[BLK/vIO | GNO BWM BC | 24/02 |
| PL1-2 [PNK | Ee BWM pce | 7320.2 |
| BoI-1 1 8LK | GND PWM PCB | 1370.2 |
| Sw2-2 | BLK | SW_GND CINK | 1379.2) |
Poss ‘ORG7GRN +13y ALARM S865 | 1370~
| PL6-10— | Poss | BLK | GNO ALARM BEB | 1370.2 |
TERMINATIONS
a. IM = “JAMMA“ EDGE CONNECTOR =, PL 15 WAY M+L PLUG FEMALE PINS a. PL2 4 WAY M+L SOCKET MALE PINS «. PLO 12 WAY 0.156" PITCH MOLEX >. PL7 15 WAY M+L PLUG FEMALE PINS e. PL8 10 WAY 0.156" PITCH MOLEX
- PLO 4 WAY JST VLP SERIES 2e, PLIO 4 WAY JST VH SERIES 2, PL11 6 WAY JST VH SERIES so. PL12 10 WAY JST NH SERIES aa. PLI3 2 WAY M+L SOCKET MALE PINS aa. PL14 = 2 WAY M+L SOCKET MALE PINS qa. PL15 10 WAY JST NH SERIES aa. PL16 @ WAY JST NH SERIES ae. PLI7 4 WAY JST NH SERIES se. SWI STD. TEST SWITCH swe STD. TEST SWITCH Sw3 250 FASTONS + COVERS ae. POS! TINNED ENDS ao. POS2 250 STONS + COVERS a1, POS3 TIN ENDS aa. POS4 TIN ENDS asa. POSS TINNED ENDS as. LM1 = COIN MECH LAMP HOLDER a