Mortal Kombat 1 (16-40025-101 July 1992)
Mortal Kombat (rev 5.0 T-Unit 03/19/93) (Midway, 1992) · Manual · 62 pages · 41 sections · original scan
16-40025-101
OPERATIONS MANUAL
* Operation & Adjustments * Testing & Problem Diagnosis * Wiring Diagrams & Schematics
- Parts Information =—
Mortal Kombat Instructions
Insert two coins to start a game; insert one coin to continue.
In a two player game, the loser pays and the winner stays.
Press the Punch and Kit buttons to attack an opponent.
Use the joystick to make the screen player jump or duck, and move left or right.
Use joystick and button combinations to discover secret moves.
MIDWAY Manufacturing Company reserves the rights to make modifications and improvements to its products. The specifications and parts identified in this manual are subject to change without notice.
MORTAL KOMBAT
TABLE OF CONTENTS Section 1 Operation and Troubleshooting
Set-up Procedure Installation & Inspection Location Requirements. Cabinet Assembly Diagrai Servicing..... Game Features Starting-up.... Player Controls. Control Panel Diagram Game Operation Control Switches... Control Switch Location Diagram: Menu System Operation Operation. Main Menu Diagnostic Tests. Switch Test DIP Switch Tes: CPU & Sound Tests... Monitor Patterns & Bum- Coin Bookkeeping. Game Audits... Game Adjustments Standard Pricing Table. Custom Pricing Table. Utilities. Troubleshootin,
Section 2 Parts Information Cabinet, Speaker, & Manuals... PC Boards, Transformer ‘Assembly, Fluorescent Lamp Assembly, Control Panel Assembly, & Monito! Cables.. Power Supply. CPU Board.. Sound Board
Section 3 Diagrams and Schematics JAMMA Chart & Interboard Wiring Cabinet Wiring Diagram. Power Wiring Diagram & Transformer Chart CPU Board Schematic... Sound Board Schemati
© Copyright 1992 MIDWAY Manufacturing Company
MORTAL KOMBAT
SECTION one
Operation
Safety Notices
The following safety instructions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply. We recommend that you read this page before preparing your game for play.
Z\\ CAUTION AC POWER CONNECTION. Before connecting the game to the AC power source, verify that the "line voltage selection chart" jumper wires are installed correctly for the line voltage in your area. For details, reter to Section 3.
PROPERLY GROUND THE GAME. To avoid electrical shocks, do not plug in the game until it has been inspected and properly grounded. MIDWAY games should only be plugged into a grounded 3-wire outlet. Shocks will also result, if the contro! panel is not properly grounded! After servicing any parts on the panel, assure that the ground wires are secure. Only then should you lock up the game.
DISCONNECT POWER DURING REPAIRS. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of ihe game.
USE THE PROPER FUSE. To avoid electrical shock, use the replacement fuse which is specified in the parts list for this game. The replacement iuse must match the original fuse in fuse type, voltage rating, and current rating.
MONITOR PRECAUTIONS. When removing or repairing the monitor, extra precautions must be taken to avoid electrical shock because high voltages may exist within the monitor circuitry and cathode ray tube (CRT) even after power hasbeen disconnected. Do not touch internal parts of the monitor with your hands or metal objects! Always discharge the CRT by ihe following method: Attach one end of a large, well-insulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again.
HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it willimplode! Shattered glass canfly eight feet or more from the implosion.
ATTENTION ! PROPERLY ATTACH ALL CONNECTORS. Make sure that the connectors on each printed circuit board (PCB) are properly connected, If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. All connectors are keyed to fit specitic pins on each board.
1-2
Setup Procedure
INSTALLATION & INSPECTION
- Remove ail items from shipping container and set them aside. Inspect the exterior of the cabinet for any damage. Remove the shipping cleats from the bottom of the cabinet.
- The keys are either taped to the coin retum slot, or attached to joystick, Unlock and open the coin and cash box doors. Remove the leg levelers and spare parts which are stored in the cash box.
- Tilt or lay the cabinet down. Locate the four threaded holes on the bottom of the cabinet (one in each corner), and install one leg leveler (with its hex nut) in each hole.
- Stand the cabinet upright and make certain that it is in a stable position. Level the cabinet.
- Remove the rear door of the cabinet. Inspect the interior for any signs of damage. Check all major assemblies to assure that they are mounted securely.
- Refer to the game's Cabinet Wiring Diagram (section 3), and check to see that all cable connectors are correctly secured. DO NOT FORCE CONNECTORS. Watch for damaged connectors and avoid making reversed connections.
- Determine the value of your line voltage with a meter. Then, check the power input wires to the main power supply transformer. Be sure they are connected to taps which correspond to your local line voltage value. If necessary, reconnect the power input wires to the transformer in accordance with the Tranformer Chart in section 3.
- Lay the line cord (connected to the Power Chassis) in the slot along the bottom edge of the rear cabinet door. Replace the rear cabinet door. Close and lock the front coin and cash box doors.
- Connect the line cord to a grounded (3-terminal) AC wail outlet.
- Switch On the game, using the On/Off switch located on the upper left rear of the cabinet, to verify proper operation. Game Location Requirements
Power Domestic 115V @ 60 Hz Foreign 230V @ 50 Hz
Temp, 32° F to 100° F (0° C to 38° C)
Humidity Not to exceed 95% relative.
Cabinet Assembly
Fluorescent Lamp Assembly
Screened Marquee
Speaker & Cap. Assembly
Coin Door
Front Door Assembly.
Front View
1-4
Cabinet Assembly
On/Off Switch
Vent Cover
Switcher Power Supply.
Power Pack Assembly.
Rear View
1-5
AN Caution The monitor DOES NOT contain an isolation transformer in its chassis (it is mounted instead in the Power Chassis Assembly located on the floor of the cabinet). Whenservicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM THE LINE VOLTAGE WITH AN ISOLATION TRANSFORMER.
JN Caution
While removing the four bolts, firmly Support the monitor from the front of the CRT so that it will net slip.
Servicing
i Servicing the Control Panel Switch Off power to the game. The control panelis heldin place by two latches (located inside the cabinet, on the left and right sides of the control panel) which provide constant pressure on the strikes. The latches can be reached through the coin door opening. To release the latches, lift the latch handle and unhook the wire fasteners. Carefully use the joysticks to lift the control panel. ‘Tilt the control panel until it rests on its support bracket. To reinstall the control panel, check for proper cable connections, including the ground strap, and use the joysticks to lower it into position, avoiding pinched wires. Reclamp the latches.
Removal of Viewing Glass Switch Off power to the game, and open the control panel. Remove the five hex head screws and the black metal strip at the bottom of the viewing glass. Carefully, slide the glass from its side grooves and lift it clear of the cabinet.
Removal of Monitor Bezel Switch Off power to the game. Open the control panel and remove the viewing glass. Lift the bezel off of the monitor.
Monitor Replacement We recommend that you read the WARNINGS section thoroughly before beginning this procedure. Switch Off power to the game. Remove the viewing glass and the monitor bezel. Completely disconnect the monitor from all of its cabling, including its chassis ground strap. Remove the four bolis securing the monitor's mounting flanges to its mounting panel. Pull the monitor carefully from the cabinet front.
i Removal of the Marquee Switch Off power to the game. Remove the five hex head screws from the black strip on top of the cabinet. Remove the strip and carefully lift the marquee. Store the marquee carefully WARNING If you drop a fluorescent tube and it breaks, it willimplode! Use care in handling. to prevent damage.
The fluorescent tube is now accessible for replacement. Grasp the tube, give it a quarter turn, and remove it from its socket. Carefully place a new tube into the socket, and turn to reinstall.
lf Removal of the Fiuorescent Light Assembly Switch Off power to the game. Remove the marquee glass. Disconnect the fluorescent light assembly from its power cable. Remove the screws that hold the assembly to the cabinet then lift out the assembly.
i Removal of the Speakers Switch Off power to the game. Remove the marquee glass. The speakers pull out from the front of the cabinet. Be sure to disconnect the cabling and remove the nuts on the mounting screws before attempting to pull the speakers out of their enclosure. Carefully reinstall the seals upon completing any task in the speaker enclosure.
@ Volume Control, Test/Diagnostics Switch, and Service Credit Switch Open the coin door to locate the game's volume control and Diagnostic switches on the small panel atop the cash box cover. The Volume Control is the white knob on left end of the panel. Tuming the knob clockwise increases the volume. The upper right switch on the bracket is the Test/Diagnostics Switch that enables activating the game's Menu System. The lower right switch is the Service Credit Switch, which allows adding credits toagame for service testing without affecting the game's bookkeeping total.
Note
When an erroris detected during Startup Tests, game start-up does not progress, and an error message appears on the screen.
Discover secret moves by using joystick and button combinations. Game Features
STARTING UP Switch on power to the game. A "rug" pattern appears on the CRT screen. When the "rug" pattern ends, the screen shows CHECK- ING SCRATCH RAMS, and then CHECKING ROMS. The next screen shows MORTAL KOMBAT REVISION LEVEL, CMOS TEST OK and the COIN SETTING. The game then begins the Attract Mode.
Insert the desired amount of coins or tokens. Press the appropriate Start button.
Player Controls
Start Buttons Each player has a Start Button which allows him/her to begin or continue play.
High Kick/High Punch Buttons Allows the screen player to kick or punch an opponent in the upper body.
fq Low Kick/Low Punch Buttons Allows the screen player fo kick or punch an opponent in the lower body.
Block Buttons Allows the screen player to biock an opponent's punch, kick or special move. @ Joystick Allows the screen player to move, flip, jump and duck.
Control Panel
1-8
Game Operation
The MORTAL KOMBAT Control Switches are located inside the coin door. These switches allow the operator to customize some features of the game.
Control Switches ™] The Coin Door Slam Tilt Switch detects any forceful vibrations against the Coin Door. This eliminates pounding for free games.
The Volume Control allows increasing or decreasing the volume level of the game music and speech. For greater profits, set your game's volume level at a nice loud setting.
The Test/Diagnostic Switch (slide switch) allows you to activate the game's Menu System. Move the Test Switch to access the Main Menu. To exit the Menu System, select EXIT TO GAME OVER from the Main Menu, then press any control panel button.
The Service Credit Switch (pushbutton switch) is a special feature switch that allots credit without affecting the game's bookkeeping total.
Slam Tilt Switch
Volume Control
Testi/Diagnostics Switch
Service Credit Switch Cash Box Enclosure
Control Switch Locations
Menu System Operation
OPERATION All MORTAL KOMBAT Game Audits, Adjustments, and Diagnostics are options of the Main Menu. Each option, inturn, has its own menu, listing several choices that you may act upon as desired.
Move the Test Switch (on the cashbox lid panel), or close Switch #8 of DIP Switch Bank #2, to activate the Main Menu (shown below). Game adjustments, bookkeeping, and diagnostics are all accessible from this menu.
Move any joystick up or down to cycle through the menu options. Notice that the options are highlighted in sequence. Press any button to activate a highlighted option.
Select With Any. Stick
Activate with Any Button
Diagnostic Tests Coin Bookkeeping
‘Game Audits
Game Adjustment
‘Utilities _
Exit Test Menu
Main Menu
1-10
DIAGNOSTIC TESTS To enter the Diagnostic Tests from the Main Menu, move any joystick to select (highlight) the Diagnostic Test option, and press any control panel button to activate the option.
Select With Any Stick
Activate With Any Button
Switch Test
DIP Switch Test
CPU Board Test Sound Board Test Monitor Patterns Burn-in Test Return To Main Menu
Diagnostic Menu
Switch Test The Switch Test allows the operator to test the switches on the control panel and the coin door.
Select the Switch Test by using any joystick to highlight the Switch Test option; then, press any control panel buttonto activate it. The top of the screen shows a layout of the control panel and the bottom of the screen lists the coin door switches. Pressing a switch causes the corresponding switch location on the screen to light. Release the switch and the screen returns to normal.
Press the Start buttons together to return to the Diagnostic Menu.
DIP Switch Test The DIP Switch Test allows the operator to check the position of the two 8-position DIP Switches on the CPU Board. The operator can also change the setting of each position of each DIP Switch during this mode.
Use any joystick to select the DIP Switch Test and any control panel button to activate it. The screen displays a layout of their current settings.
To change a DIP Switch setting, press the switch to the desired Setting, then check the screen to verify that the switch now shows the new setting.
Press any control panel button to return to the Diagnostic Menu.
DIP Switch 1 Settings Table swi/ sw2/ swa| sw4]sw5 | swe] sw7|/sws Violence On Off * On Blood in game Off -
On
Low Blow in game oft* | On L Attract Sounds On ont On | Not Used ont | ont) oft | on: tL ;On | On | On | On
DIP Switch 2 Settings Table swi | Sw2 {SH [swa_|sws |swe | sw7 | swe | DIP Switch | Off’
| Coin A | Lon | | | | | | |
Coinage ot | of ont
| USAT | Gert | Fret |
On | of | off USA2 Ger2_—Fr2 Of |on | of
| UsA3 | Gerd | rd) | ||
| USA4s | Gera | Fra | n | On | Off | |
| USAECA GerECA | Freca | Off | Off | | On | | | |
| NU | NU | NU | On | Off | On |
| NU | NU | NU | Off | On | | On |
| | | Free Play Free Play| On | | On| On | | |
fouey on’) one | On | Off German off | On | French On
Not Used on i
One Counter on Two Counters Not Used oft* On
- Indicates Factory Setting
1-12
CPU Board Test The CPU Board Test (much like the Start-up Test) allows the operator to check the RAMs and ROMs.
Select the CPU Board Test with any joystick; then, press any control panel button to activate the automatic test of the CPU Board's RAMs and ROMs. When this testis activated, a "rug" pattern appears on the screen. The screen then changes to show the layout of the RAMs, and ROMs. A ROMor RAM location that is shown as black with awhite outline is used and should turn either red or green. A ROM or RAM location that is shown as gray with a white outline is not used in this game. During the test, ROM or RAMs are good, if they turn green; they are faulty, if they turn red.
The CPU Test pauses when a bad ROM or RAMis detected. Press any button to continue the test.
Sound Board Test The Sound Test allows listening to some of the sounds that this game is capable of producing. This test also emits a tone for each fault that is detected.
Select the Sound Board Test with any joystick; then, press any control panel button to activate the test. The screen displays two test options:
GENERAL TEST analyzes the sound circuitry. The screen shows a list of error codes. A successful test causes a single "tone" to sound. Detection of a fault causes a series of tones or no tone at all to sound.
PLAY SOUNDS tests synthesized & digitized sounds from the Sound Board. Advance to the next sound by moving any joystick, and press any control panel button to activate the sound.
Select RETURN TO MAIN MENU or BACK TO DIAGNOSTIC MENU. Press any control panel button to activate your selection.
General Test
Play Sounds
Return To Main Menu Back To Diagnostic Menu
Sound Test Menu
1-13
Monitor Patterns The Monitor Paiterns Test provides a menu for testing the monitor. Select the test with any joystick and activate with any control panel button. Once the Monitor Patterns Test is activated, move any joystick to select a test option; press any control panel button to activate the option. Press any control panel button again to return to the Monitor Patterns Test menu.
Select With Any Stick Activate With Any Button
Red Screen Green Screen Blue Screen Color Bars Crosshatch Patterns
Back To Diagnostic Menu Return To Main Menu
Monitor Pattern Menu
The RED, GREEN, and BLUE SCREEN tests fill the screen with either red, green or blue. The COLOR BARS test fills the screen with several shades of colors to help with red, green and, blue level adjustments. Each color should appear sharp and clear. The CROSSHATCH PATTERNS test fills the screenwith agrid and a series of dots. The grid and the dots should be clear. The dots should appear round.
\f any of the Monitor Pattern Tests shows aneed for adjustment, use the proper white knobs on the Monitor Board.
Use any joystick to select RETURN TO MAIN MENU or BACK TO DIAGNOASTIC MENU and activate with any control panel button.
Burn-in Test The Burn-in Test continually repeats the CPU Board Test. Move any joystick to select the Burn-in Test; then, press any control panel button to activate the test. When the Burn-in Test detects an error, the test stops and displays an error message onthe screen. The second page of the Audit Table specifies the number of Burn-in cycles successfully completed. Use this test to find intermittent CPU problems.
To exit this test, switch the garne Off then On again.
1-14
COIN BOOKKEEPING To enter the Coin Bookkeeping from the Main Menu, move any joystick to select the Coin Bookkeeping option; then, press any control panel button to activate it.
The Coin Bookkeeping Table records the coinbox totals and game play counters. The left side of the table names the bookkeeping item; the right side shows the number of coins, credits, or plays for each item.
To exit Coin Bookkeeping, move any joystick to select RETURN TO MAIN MENU; then, press any control panel button to activate it.
Left Slot Coins Right Slot Coins Third Slot Coins Fourth Slot Coins Service Credits Paid Credits Total Plays Plays Until High Score Reset gaocooocoo
More Detailed Data Retuth To Main Menu
Coin Bookkeeping Table
Left Slot Coins Right Slot Coins Third Slot Coins Fourth Slot Coins Total Collections ooocGgo
Clear Coin Meters Return To Main Menu
Total Collection Table
1-15
GAME AUDITS To enter Game Audits from the Main Menu, move any joystick to select the Game Audits option; then, press any control panel button to activate it. To advance to the next (or reiurn to the previous) page of the Game Audit Table, move any joystick to select either "Next Audit Page", or"Previous Audit Page"; then, press any control panel button to change the page.
The Game Audits Table records the game play statistics. The left side of the table names the Audit item; the right side shows the amount of play.
Hours Game Was Played 0 Total Play Time : 0 Hours Played With 1 Player 0 Hours Played With 2 Players 0. Total Plays 0 Continues Taken 0 Burn-in Loops Successfully Completed _ 0 Sa es on snore aa Next Audit Page Return To Main Menu
Page 1 of Audit Table
Cage Choosen — Kans Choosen Raiden Choosen Sub-zero Choosen Scorpion Choosen Sonya Choosen Error Traps ocooceooe
Previous Audit Page Return To Main Menu
Page 2 of Audit Table
To exit the Game Audit Table, move any joystick to select RETURN TO MAIN MENU; then, press any control panel button to activate your selection.
1-16
GAME ADJUSTMENTS Move any joystick to select the Game Adjustment option on the Main Menu; then, press any contro! panel button to activate it.
The Game Adjustments Menu allows the owner/operator to change the Game Pricing and Game Difficulty.
The Game Adjustments Menu offers several options. Each option has several choices. Move any joystick to select an option; then, press any control panel button to activate that option. The next Menu screen provides a setting choice. Move any joystick to modify the setting value; then, press any control panel button to lock in the new value and return to the Adjustment Menu. Move the joystick up to increase the setting value, move the joystick down decrease the setting value.
To exit the Adjustments Menu, use any joystick to select RETURN TOMAIN MENU; then, use any control panel button to activate your selection.
Select With Any Stick. Press Any Button To Modify:
Return:To Main Manu Standard Pricing Custom Pricing Free Play Computer Difiiculty Winning Streak Reset Return To Main Menu
Game Adjustment Menu
Note
Game Adjustments are explained in more detail on the following page.
Adjustment values set by DIP Switch, override adjustment values set by the menu system.
Game Adjustments
Standard Pricing Standard Pricing allows the operator to choose any of the "Standard" selections for the Standard Pricing Table. See page 1-19.
Modify the setting value with any joystick. Press any control panel button to lock in the new value and return to the Adjustment Menu.
Custom Pricing Custom Pricing allows the operator to install pricing other than that of the Standard Pricing Table. Custom Pricing also allows the operator to select the maximum amount of credits per game, the amount of credits required to start a game, and the amount or credits required to continue a game. This option is being adjusted from the Dip Switch Settings. See page 1-20.
Modify the setting value with any joystick. Press any control panel button to lock in a new value and return to the Adjustment Menu.
Free Play This option selects free play. The setting choices for this adjustment are:
- No (factory)
- Yes
Computer Difficulty This option determines the difficulty level of game play. The setting choices for this adjustment are: -1 (Extra Easy) -2 (Easy) -3 (Medium; factory) -4 (Hard) -5 (Extra Hard)
Winning Streak Reset This option resets the highest scores after a selected amount of games are played. The setting choices for this adjustment are:
- Reset every 5,000 games.
- Reset every 10, 000 games (factory).
- Reset every 15, 000 games.
- Do Not Reset.
1-18
Standard Pricing Table
| Name | Settings | Left | Center | Right | | Fourth |
Credit/Coin Chute (Chute | Chute | Chute
| USA 1 | 1/25¢ | 25¢ | 25¢ | ||
| USA 2 | 1/50¢ | 25¢ | 25¢ | ||
| USA3 | 1/50¢, 3/$1.00 | 25¢ | 25¢ | ||
| USA 4 | 1/50¢, 4/$1.00 | 25¢ | 25¢ | ||
| USA ECA | 1/25¢, 4/$1.00 | $1.00 | 10¢ | 25¢ | 5¢ |
| German 1 | 1/1 DM, 6/5 DM | 1DM | 5 DM | ||
| German 2 | 1/1 DM, 7/5 DM | 1DM | 5DM | ||
| German 3 | 4/1 DM, 8/5 DM | 1DM | 5DM | ||
| German 4 | 1/1 DM, 5/5 DM | 1DM | 5DM | ||
| German ECA | 1/1 DM, 2/2 DM, 6/5 DM | 5DM | 1DM | 2DM | ||
| France 1 | 2/5 F, 510 F | SF | 10 F | ||
| France 2 | 2/5 F, 4/10 F | SF | 10F | ||
| France 3 | 1/5 F, 3/10 F | 5F | 10F | ||
| France 4 | 1/5 F, 2/10 F | SF | 10 F | ||
| France ECA | 1/3X1F, 2/5 F,5/2X5F | 1F | 10F | 5F | ||
| Swiss | 1/1 F, 6/5 F | 1F | 5F | ||
| Italy | 1/500 Lire | 500 Lire | 500 Lire | ||
| UK 1 | 1/20 P, 3/50 P | 20P | 50P | ||
| UK ECA | 1/30 P, 2/50 P, 4/£1.00 | £1.00 | 20P | 50P | |
| Spain 1 | 1/25 Peseta, 5/100 Peseta | 25 Peseta | 100 Pesetal | 10P | |
| Japan 1 | 1/100 Yen | 100 Yen | 100 Yen |
If option desired is not shown above, use custom pricing .
1-19
Custom Pricing
Select With Any Stick = Press Any Button To Modify.
Return'To Adj. Menu
- Left Chute Units
- Right Chute Units
- Third Chute Units
- Fourth Chute Units
- Units/Credits =
- Units/Bonus — ae
- Minimun Units Required
- Credits To:Start
- Credits To Continue
- Coins Per Dollar — Maximum Credits Return To Adj. Menu
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8) Coins inserted accumulate units. This adjustment specfies the number of units given for each coin in the fourth chute (see "units/credit”).
This is the number of coin units required to buy one credit.
One bonus creditis awarded after this many coin unitshave accumulated.
No credits will be awarded until this many coin units have accumulated.
Each player needs this many crediis to begin a game.
Each player needs this many credits to continue a game.
The detailed bookkeeping screen shows total collections based on this many coins per dollar. (Set to zero to disable the display of money totals)
This is the limit for the credits counter. Additional coins inserted will be lost (faciory setting: 30)
1-20
UTILITIES
Move any joystick to select the Utilities option on the Main Menu; then, press any control panel button to activate it.
The Utilities Menu allows the owner/operator to clear ihe game's bookkeeping memory and to install a custom message.
Select With Any Stick _ Activate With Any Button
Clear Credits Clear Coin Counters Clear Game Audits —ResetHigh Score > Default Adjustments. _ Full Factory Restore Return To Main Menu -
Utilities Menu
Move any joystick to select an item from the Utilities Menu; then, Press any control panel button to activate that item. After an item has been activated, you are given the option of resetting that item or not. For example,
CLEAR COIN COUNTERS ? ARE YOU SURE ?
Move any joystick to choose YES or NO; then, press any control Panel button to lockin your choice and to return to the Utilities Menu.
To exit ihe Utilities Menu, move any joystick to select RETURN TO MAIN MENU; then press any contro! panel bution to activate your selection.
1-21
Problem
No Picture or Distorted Picture.
Tum game On and nothing happens.
No sound.
No General Illumination.
Move joystick and the screen player does not move.
Press Start Button and nothing happens.
Press any control panel button and screen player does not move.
No credit given when coins are inserted.
Toomany credits fornumber of coins inserted.
Game stays in test mode.
Troubleshooting
Possible Solution
Check for faulty video board or monitor. Check for disconnected video signal cable.
Check line fuse. Check for +5Vdc at pins C, D, 3, and 4 of the JAMMA Connector.
Check the speaker and speaker connection to pins L and 10 onthe JAMMA Connector. Check volume control setting. Check for +12V dc at pins F and 6 on the JAMMA Connector. Check interboard wiring from CPU Board to the Sound Board.
Check the 1A., S.B. fuse.
Check for open wires beiween the joystick and CPU Board. Check for contamination on joystick switch contacis and CPU Board pins. Check for proper ground.
Check for open wires between the button and CPU Board. Check for contamination on CPU Board pins or ihe button switch blade contacts. Check for proper ground.
Check for open wires between the button and CPU Board. Check tor contamination on CPU Board pins or the button switch blade contacts. Check for proper ground.
Check DIP switch coin setting. Check for contamination on coin switch contacts. Check for an open wire between Coin Switch 1 and pin 16 on the JAMMA Connector or Coin Switch 2 and pin T of the JAMMA Connector.
Check Game Pricing setting. Check for a short between pins T & 16 onthe JAMMA Connector.
Check that the Test Switch in the coin door is set to Off.
1-22
MORTAL KOMBAT
SECTION two
Parts
Cabinet Hardware
Cabinet Assembly Shaft Caster Leg Leveler Plate Leg Adjuster, 3.0” Caster Wheel Power Switch Plate Assembly Power Switch
Front Door Assembly Latch Bracket
Bezel & Instruction Card Set 25" CRT Bezel Instruction Card A-15639-40025 02-4404 01-9155 08-7377 20-9627 A-15924 5640-13250-00
A-14267 01-6994
A-15654 03-8497 31-1697-40025
Coin Door Assembly A-14975 Test Switch A-13115 Coin Door Cable H-14923 Coin Door, U.S.A. 09-20000-V-1
Line Voltage Cable Asembly A-14201 Glass Retainer Bracket 01-9607 20" Vent Hole Cover 03-7602 Lamp Lock 03-8327 Glass Edge Channel 03-8358 Clear Glass 08-7456-4 Clear Glass 08-7456-10 Rear Door 11-1075 TAG Special Wrench 16-9074 Toggle Latch 20-9347 Long Arm Key T-20 20-9620 #555 Bulb, 6.3V 24-8768 Marquee 31-1644-40025 Marquee Retainer 03-8252-2
Speakers
Speaker & Cap Assembly A-14968 Piezo Speaker Cable H-14922 Speaker Cabie H-15701 Speaker Grille 01-10777 Cap. 10pf, non-pol, 50V,20% Tweeter Speaker, 40, 15W 6" Speaker, 4Q, 25W 5045-12914-00 5555-12924-00 5555-12929-00
Manuals
Monitor Manual Instruction Manual
2-2 16-3000-103 16-40025-101
PC Boards
Chassis Panel Assembly Y-Unit CPU Assembly Power Supply Assembly Sound Board Assembly A-14157-3 A-13234-40025 A-15202-1 A-14732-40025
Transformer Assembly
Power Pack Assembly Line Cord Assembly Power Pack Chassis Assy Power Pack Jumper Cable Transformer Jumper Cable Line Filter Jumper Cable G.I. Jumper Cable Varistor, 130V, 10J Line Filter, 5 Amp Power Transformer Fuse, SB, 1A, 250V Fuse, SB, 3A, 250V Fuse Holder, Panel A-15916 A-15921 A-15915 H-13265 H-13378 H-15922 H-15945 5017-09044-00 5102-10310-00 §610-13326-00 5731-06569-00 5731-10356-00 5733-12869-00
Fluorescent Lamp Assembly
Fluorescent Housing & Bracket C-12679 Housing Mounting Brkt 01-9146 Light Fixture 20-9590 18" Fluorescent Bulb, 15 W 24-8809
Control Panel
Housing & Control Panel Assembly A-15644 Control Panel Assembly A-15645, Plate A-15638 Control Panel Cable —_H-15669 Latch Bracket 01-6994 Latch Bracket 01-9605 Wood Control Panel 11-1076 Red Pushbutton 20-9687-1 White Pushbutton 20-9687-2 Blue Pushbutton 20-9687-3 8-way Joystick 20-9694-1 Screened Overlay 31-1696-40025 Wood Housing 11-1018-2 Toggle Latch 20-9347
Monitor
Monitor Support Bracket 01-9969 25" Monitor 5675-12787-01
2-3
Cables
Power Pack Jumper Transformer Jumper Line Voltage Cable Piezo Speaker Cable Coin Door Cable Video Extension Cable Sound Power Speaker Cable Video Signal Cable Switch Power Cable Control Panel Cable Main Harness Speaker Cable Line Filter Jumper G.I. Jumper Cable 20-pin Ribbon Cable H-13265 H-13378 H-14235 H-14922 H-14923 H-14924 H-14925 H-14949 H-15203 H-15669 H-15670 H-15701 H-15922 H-15945 5795-10937-06
A-15202-1
Power Supply Switcher Assembly
Part Number Description H-15203 Switch Power Cable 01-10500 Mounting Bracket 01-10573 Shield 20-9700 P/S Switcher Supply
fe) > ¢ D c x > c D 5 c D ¢ , ¢ D > c D 5 ¢ ¢ > c x 5 c ) ¢ > c DC > c > ¢ > c D > c > ¢ > c > ¢ > c > ¢ c ) ¢ > ¢ D ¢ > c > € > c D D C DC > c ¢ > c D > c ) ¢ > c DC > < x D i > ¢ ) ¢ c D > ¢ D 5 c DC > » ¢ > c D > ¢ > > c x D c D ¢ > c > ¢ >
° fo} 5 @ S
VIOLET
GREEN BLACK // GRAY/GREEN BLACK GRAY/YELLOW
i s s|sle >|/¢/¢e & | 2]6/6|3)F]4]2])¢e 7 li (
2-5
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Part Number
5281-09737-00 5317-12211-00
5317-12212-00
5317-12208-00
5340-12840-00 5700-12047-00 §521-10421-00 5521-10318-00 5283-10468-00 5019-10849-00 5286-13209-00 5700-12253.00 5280-09309-00 5281-09487-00 5434-12255-00 5700-09915-00 531 1-12287-00
5700-10176-00 5311-12285-00 5340-12014-00 5283-10552-00 5370-12602-00 5317-12023-00 5700-1 2088-00
5700-12254-00 5317-12024-00 5700-08985-00 5010-08991-00 5010-10204-00 5010-10205-00 5010-10000-00 5010-09219-00 5010-08772-00 5010-09001-00 5010-09036-C0
5010-09416-00 5010-08997-00 5010-09534-00
5043-08980-00 5040-08986-00 5043-09845-00 5041-09243-00 5043-08996-00 5019-12611-00
5019-09362-00
5019-10143-00 5060-10396-00 A-13234-40025 CPU Board Parts
Designator Description
ut Ic, 74LS86 U2, U20, U24, U43, IC, 74ALS541 Us1, US2, U70 U3, U6, U7,U21, IC, 74ALS574 25, USO, US8, Us3, Usa, U71, U72, U74, U79, Usa, UBS U4, U22, U54-U57, IC, 74ALS245 US9, U60, U75-U78, Ugo, U81, U94, U110 U5, U23 IC, 8K x 8 Static RAM U8, U5S2,U53,U65 —24-pin Socket ute 48Mhz Xtal ut7 2aMhz Xtal U19, U45 IC, 74F74 U27,U34,U44, U48 10002 DIP Res. U3s IC, 744S00 Use 68-pin Socket U37 IC, 7407 U38 IC, 74.874 U39 MAX691 Udo, Ua1, U42 20-pin Socket Uae, U47, U87, U100 IC, 74HC541 U101, U103, W104 uag 28-pin Socket U51, U73, U82 IC, 74HC573. Ue6-U69 IC, 4464 DRAM, 64 x 4 uaa IC, 74F04 Use IC, ULN2064B uss IC, 74ALS138 U89-U93, U95-U98, 32-pin Socket U105-U109, U111-U114 Uso 114-pin Socket U102 IC, 74ALS139 Uns 40-pin Socket Rt, R24, R27 4.7KQ Res., 5%, 1/4W R2, R7, R12 1KQ Res., 2%, 1/4W R3, RB, R13 2KO Res., 2%, 1/4W Ra, R9, R14 3.9KQ Res., 5%, 1/4W RS, R10, R15. 8.2KQ Res., 5%, 1/4W Re, R11, Ri6 15KQ Res., 5%, 1/4W R23, R25 3309 Res., 5%, 1/4W R26, R29-R34, REO 1000 Res., 5%, /4W R51 R35-F37, R46-R4B 4700 Res., 5%, 1/4W R38-R45 2.7KQ Res., 5%, 1/4W We, Wa, Wi1, W12, 09 Res., 1/4W W14, W21, W22, W24, w27, W29, W30, W32, W34, W36, W39, Wat, wae, Was, W47, W48, W50, W52, W55, W57, W58, W60, We2, We5, Wes, Wea, W71, W73, W75, W77, WB0 B O1pf Cap., 10V, Axial 100pf Cap., 10V, Axial C1, C2, C5, C10 C3, C4 .001pf Cap., 10V, Axial C6-C9 10pf Cap., 10V, Axial cH “pf Cap, Axial SR1, SR3, SR8, 4709 SIP, 5 Res. SR9, SR12, SR13, SR1i8 ‘SR3, SR4, SR6, 4.7KQ SIP, 9 Res, SR7, SR11, SR15, SR17, SR19, SR20, SR21, SR22, SR23, SR24, SRC1, SRC2, SRC3 SR5 4702 SIP, 9 Res SRC4, SRC5, 4.7KQ SIP, 470pf SRC10, SRC14, SRC16 Part Number
5671-09019-00 5551-09822-00 §645-09025-00 5641-12551-00 §881-12315-00 5791-10862-08 5791-12461-12 5791-10850-00 5791-09437-00 5791-12461-10 5700-12252-00 5791-12461-05, 5791-12461-04 §791-12461-20 §791-12461-04 5880-11056-00 03-8338-1 A-5346-40025-1 5400-12220-00 A-5346-40025-2 A-5346-40025-3 A-5346-40025-4 5340-12558-00 A-5346-40025-5 A-5346-40025-6 A5346-40025-7 A-5343-40025-1 A-5343-40025-10 A-5346-40025-8 5410-12239-00 5340-12213-00 5341-13297-00 5341-13297-01 5341-13297-02 5341-13297-03 §341-13297-04 5341-13297-05 5341-13297-06 5341-13297-07 5341-13297-08 5341-13297-09 5341-13297-10 5341-13297-11 Designator
LED1, LED2 ut DS1, DS2 swi Bi J2 J4 J6, U7 JB J12 U12-U15. S13, J3 J9A, JSB S14 B1
us. U36 U40 U4t uaz ag
Us3 U6S us9 U105 uns ug9 U10-U15, U28-U33 uit
U106 u112 Use U107 U113 u97 U108 uta ug8 U109 Description
LED, Red Inductor, 4.74H DIP Switch 16-pin Pushbutton Switch Battery Holder 8-pin Connector 42-pin Connector 26-pin Ribbon Connector 20-pin Ribbon Connector 10-pin Connector 24-pin Socket 5-pin Connector 4-pin Connector 20-pin Connector 6-pin Connector Lithium Battery, 3A 1/4" Spacer IC, PLD Color RAM Control IC, TMS34010, 50 GSP IC, PLD Address Decode IC, PLD Video RAM Control IC, PLD Local Contra IC, 8K x8 Static RAM, 150ns IC, PLD Video RAM Sequencer IC, PLD Image ROM Control IC, PLD Miscellaneous Control IC, Game EPROM IC, Game EPROM IC, PLD Autoerase Controller IC, Custom ASIC IC, VRAM 64K x 4, 150ns Ic, ROM Ic, ROM Ic, ROM IC, ROM Ic, ROM Ic, ROM Ic, ROM Ic, ROM Ic, ROM IC, ROM ic, ROM Ic, ROM
A-14732-40025
Sound Board Assembly
eLn aD a
£Ln
gl 3s} (e864 vice] eo eza} an ia ay
2-8
Part Number
5340-12958-00 5340-12959-00 5281-09850-00 5281-09215-00 5281-09851-00 5281-09487-00 5281-09745-00 5281-09246-00 5281-09733-00 5281-09486-00 5340-12278-00 5370-12260-00 5460-12743-00 5370-12960-00 5370-12730-00 5371-12727-00 5370-12963-00 §521-10931-00 5520-09020-00 5010-09534-00 5010-12961-00 5010-09039-00 5010-10170-00 5010-09036-00 5010-09187-00 5010-09160-00 5010-09416-00 5010-09358-00 5010-08998-00
5010-08983.00 5010-10000-00 5010-08991-00
5010-09219-00 5010-09034-00
5010-09269-00 5010-09324-00 5010-09325-00 5010-09035-00 5010-10987-00 5010-10650-00 5010-08776-00 5010-10257-00 5010-12927-00 5010-09162-00
5010-12965-00 5010-09134-00 5010-12964-00 5048-11027-00 5043-10264-00 5043-09492-00
5048-12748-00 5048-11030-00 5048-1 2506-00 5048-11031-00 5048-11065-00 5048-12967-00 5048-1 1072-00 5048-12966-00 5043-08980-00
5045-12926-00 5043-08996-00 5048-1 2036-00 5040-09365-00 5040-09343-00
5040-09332-00 Designator
U7, U11, U24 U6, U10, U25 U1 U26 Uat U9, U22, U23 Us U20 u17 U5, U16 U2 U30 VAt u29 U32, U33 Ui5. ust Y2 v1 ‘W2, W3, W5,W7, W8 R72-R74 R89 R11-R21 R4, R30, R90 R27 R83 R32, R43, R41, R82 R43, RES R22-R24, R26, R59,
A1-R3, R5-R10, R25, Re4-R86, R91 Reo R62, R63, R67, R70, R80 Rea Res R36 R29, RS3, R81 R77, R78 R38, R45, R51 R31, R71 R35 R79 R33, R48, R54, RSS, Reo, R65 R39 R40, R44, R46, R52 R37, R42 59, C60 C50, C62 C35-C45, C47, C49, C98 C54, C61, C96. c7t ¢78 C48,C55, C76 cég
C2-C26, C28, C29, C31-C33, C97, C99 ©90-C92 C72, C74, C88, C89 C65 Ces C46, C53, C57, C64, 67073, C75, C81, C100, C102 C63, C66, C80 A-14732-40025
Sound Board Parts
Description
IC, 26L831 IC, 26L832 IC, 7aLS11 IC, 74LS04 IC, 74L814 IC, 74LS74 IC, 2418138 IC, 7418139 Ic, 74L8174 IC, 74LS374 IC, Static RAM, 8K x 8 IC, 3340 Attenuator IC, 7809 Regulator, +9V IC, LM324 Op Amp IC, TLO84 Op Amp ‘AD7524 DAC HA13116 Pwr. Amp Mhz Oscillator 3.58 Mhz Crystal 09 Resistor 3.32 Res., 5%, 1/2W. 102 Res., 5%, 1/4W 47Q Res., 5%, 1/4W 1002 Res., 5%, 1/4W. 1509 Res., 5%, 1/4W. 2200 Res., 5%, 1/4W 4700 Res., 5%, 1/4W 1KQ Res., 5%, 1/4W 2.2KQ Res., 5%, 1/4W
3.3KQ Res., 5%, 1/4W 3.9KQ Res., 5%, 1/4W 4.7KQ Res., 5%, 1/4W
8.2KQ Res., 5%, 1/4W 10KQ Res., 5%, 1/4W
12KQ Res., 5%, 1/4W 27KQ Res., 5%, 1/4W 39KQ Res., 5%, 1/4W A7KQ Res., 5%, 1/4W. S6KQ Res., 5%, 1/4W 62KQ Res., 5%, 1/4W 68KQ Res., 5%, 1/4W 75KQ Res., 5%, /4W 82KQ Res., 5%, 1/4W 100KQ Res., 5%, 1/4W
130KQ Res., 5%, 1/4W 150KQ Res., 5%, 1/4W 820KQ Res., 5%, 1/4W 33pf Cap., 10% 68pt Cap., 10% 100pf Cap., 10%
220pf Cap., 10% 470pt Cap., 10% 820pf Cap., 10% 1000pf Cap., 10% 2200pt Cap., 10% 2700pf Cap., 10% 3300pf Cap., 10% 3900pf Cap., 10% Otpf Cap., 10%
Apt Cap., 10% stuf Cap., 20% 22f Cap., 10% Auf Cap., 10pf Cap., 16V, 20%
47 ul Cap., 25V Part Number
5040-09421-00 5040-09506-00 5040-12670-00 5070-0891 9-00 5160-12891-00 5551-09822-00 5700-09006-00 5700-09915-00 5700-09004-00 5700-08985-00 5700-12088-00 5791-10862-04 5791-10862-06 5791-09437-00 01-10516 4406-01128-00 4006-01003-06 20-9690-18 A-5343-40025-19 5400-10320-00 A-5343-40025-20 A-5343-40025-21 5370-1 1086-00 A-5346-40025-9 5371-11087-00 5433-12962-00 03-8338-1
2-9 Designator
C70, CB5-C87, C103 C79, C83, C84 C95 CRI Qi L1,L2 U28 u18 uta U4 U3, U12, U13 P5, P7 PE Pt
u3 u4 ui2 u13. Uta ure u2e ut Description
100f Cap., 25V 220uf Cap., 16V 2200uf Cap., 16V 1N4148 Diode MPS3646 Trans. 4.7uH Inductor, 3A 16-pin Socket 20-pin Socket 24-pin Socket 40-pin Socket 82-pin Socket 4-pin Header 6-pin Header 20-pin Header Heat Sink 6-32 Hex Nut 6-32 x 3/8 P-PH-S Spacer, 1-1/8 IC, EPROM IC, 68809E, MPU IC, EPROM IC, EPROM IC, YM2151 Sound Generator IC, PLD Sound IC, YM3012 DAC IC, OK16295, 4 Channel Mig. Spacer, 1/4”
2-10
MORTAL KOMBAT
SECTION three
Schematics and Wiring Diagrams
3-1
Ndo uo zp oL, JAMMA Chart
| Funetion | Wire Color | Pin | Pin | ‘Wire Color | Function |
| lack | 1 | A | Stack | |||
| Ground | wn | [2 | Bp | Back | Ground | |
| [+5 Volts DG. | Gray | 2 | G | Gray’ | +5 Volts DC. | |
| Gray | 4 | D_| | Gray | 45 Volts DC | |
| -5 Volts DC | Gray-Green | 5. | & | Gray-Green | |||
| +12 Volts DC | ‘Gray-Yellow | 6 | F | Gray-Yetow | +12 Volts DC | |
| Key | Z | | Key | |||
| | Counter 1 | White-Oranga | 8 | J__| White-Green_| Counter 2 ___| | |||
| NIC. | 9 | KT | Nc | —— | |
| |_ Speaker (4) | Red-Violet | rT | L | Green-Violet | speaker (-) |
| NC. | 41M | We | |||
| |Video Bad’ | Red | 42_[N | Groen | Video Grn | ||
| | Video Blue | Brown | 13 | p__| | whie | |
| |_Video Grd | Shield | 14 | R | White-Red | dit |
| [Test | Green | 1 | S| White-Violet | Slam Tit | ||
| 41 Coin | _White-Bive | is | TT | Yallow-Wnite {2 coin | ||
| 4 Start | Yeliow-Green_|_4 | a | 2Stan | ||
| Up | 48 | vt | Up | ||
| 4 Down | Orange-Brown | |_19. | wt | ||
| “Lett | Orange-Red | 20 | |X | Yellow-Red | 2 Left | | | ||
| }1 Bight | Orange. | 24 | ¥ | Yellow-Orange| 2 Right | |
| 4 High Punch. | Crange-Yellow | 22 | Z | Yellow-Violet | 2 High Punch | |
| [1 Block. | reon | 23 | 8 | 7 | ||
| 1. High Kick | Orange-Blue | 24 | b | Violet-Black | 2 High Kick |
| [awa | NC | {as | |e | Te | NG |
| Nic | Nic | 26 | |g Te | NC | |
| ‘Ground | NC | 27 | |e | [Nc | Ground. |
| Ground | Black | 28 | i | Black | Ground |
Interboard Wiring Diagram all En ay ‘9
grees
| | | | | 654321 | é |
L—__ g
| Pi | Pe | =[Iwe 8 | |
| Ribbon Cable | Power From | ro | |_;Orange-White @ |
| To CPU JB | ‘CPU J2 | PS! | | Ika |
® | teren-white 8 > Nel Sound Board e NIG} ro |P7
| “Blue! |= | J | aol f | 4. | |
| i | z | S52) | gf | ay |
| 2| | EER | 2 |
Fs) 38
| ‘ a8 | 9 | Es | ais | BB |
vel a
| E | Bes) | 3 slo |
3 a[a\ca} | /a} | 4 a)
| av | a | | | 29a | a | Jae |
| #8\3} | 13
| JAMMA Edge Connector | a sages | gage | Ssssio FSS SS gis |
j
| jest | See JAMMA Chan | 1 | 1_Ifi 2345678] | [1294 | 1294567891011 14 |
| q | we | J3 | W4 | ||
| 3 | Power to Sound | Power to | To Control Panel | ||
| 3] 2 | Board P6. | Coin Meter |
| 5 rd
I3| Y-Unit CPU Board [5] & El >
| 9A | 8B | From P1 On Sound Board | 7 | 46 |
| Not ued | cH) | Not Used | Wor Used |
3-3 ~~] Js
*20 Pin Ribbon Cable
Cabinet Wiring Diagram
- Red Line on Ribbon Cable must go to Pin -1 on both boards. Ribbon Cable may need to be twisted to accomplish this.
J2 To
pt Volume Controt
lwo 1 2 | —_Mc] 2|p7 3iKey wel 3 4[Green-Whito
+Speaker Violet] 4'
[H-aevnene <
White-Black Future Use
‘White-Brown Future Uso [Violet-Brown _2 Low Punch | Awe jKey __ |Violet-Red 2 Low Kick
raowpone [wc ___ ‘Oranga-Violet_1 Low Punch RED] +
CPU BOARD ‘Orange-Gray 1 Low Kick
NC. a 2g raoe Coin Meter
[Yoliow-Whita 7 Coin 2 [Black __ Ground ‘Orange White: Volume Conte. F ‘Green-White Volume Gortrol Yellow 5.Vac White-Yellow_ 5.9Vac_ Coin Cre Lights BQDILB® #259 (or #555) bulb Coin Door [Qrange-Green 1 Block 7 ‘Orange-Blue_t High Kick
| Key __ 4 Stan Yellow-Green = 4 Low Punch ~
SHIELDED VIDEO CABLE VIDEO COMPOSITE . NC Violet |
Z740103NNOO 3903 vAWWE Traore =aovHo) Violet |
‘Switcher | ‘Supply
Monitor Board See Power Wiring Diagram Sores)
aoe! Fae |Violet-Red 2 Low Kick __ fc Faereenp —— Control Panel
Power Wiring Diagram 1 | [7 |B To ON/OFF #)2//2/Gan Ligh Fixture
| SWITCH | 3 | |8 war | > 6OHZ |
} RLU GASLO BLK-YEL / m S0Hz
| \ | : | —{-—8 | I | 1]{1|woa | 2 | iif; we | To |
| 30 V | [wo.vera |2|/2[ vio-vera | $15 || 2 | BLK | POWER SUPPLY | ||||
| VARISTOR | tne | | | VIOB | 31/31 vion | 3||3 pwio _ | ||
| ITER | | [wio.verp | |4|/4 | vio- vei a | L | ||||
| Ls. | u | . | 1 || 1 Bus | To | |||
| a | r | = | 4 F | VEL. wr > | sovad | £/2||2 -SBM-YEL- | monitor |
| GAN | WHT-RED | SEE | 7 PES TO | 3] | 3 |wur | ||
| re | t | TRANSFORMER | COIN DOOR |
PLUG GROUND
Transformer Chart rc FROM POWER
| SWITCHES | 18 PIN CONNECTOR | 4 PIN CONNECTOR |
| YEL | 3 | WHT |
| +) 3 {zi | 70. | ar |
[2 | 120V ISOLATED FOR o| 5 MONITOR AND POWER
| L | 12 | BLK | 115 | vio.ver «|, | SUPPLY | ||
| NOTE: | 18) > | RED 1 | ) | EL | 24] |
| SHOWN AS | SEE | 5 | BLU - WHT | ie) |
JUMPERED | VOLTAGE »|
| FOR | SELECTION | 8 | ALL BRN seas 3 | VEL wHT 2 | |
| 415 VOLT | TABLE | m 111) > | =S8LK 15. 5) | 1 | 5.9V FOR COIN DOOR |
| OPERATION | iD | ALU RED —1a2 | SQV6A_YEI | UGHTS. |
XFMA'5510- 1259-00, 7 BLK.
| “lo | BLK | + | CONNECTOR |
= | 13 BLK.
TOPOWER WHT.RED |, | 2 . FROM LINE Swirenes “auc ———te | $ | $7 aye Fr
Voltage Selection Table JUMPER PINS 103.5 5-6,7-8,10-9 | 115 5-6, 7-11, 10-12 132 §-6,7-14, 10-15 207 5-9.10-8 218.5 §-9,.10-11 230. 5-12, 10-11 247 5-12, 10-14
3-4
CPU Sheet 1 of 16
3-5 BETTE i
if
‘SNE Viva O3G1A
3-6 7h sng wagy W907 SL 40 Z 188US
dd
9t JO € 1908S ndd
She VivONSS TuGGY WOT
1s Gnos=
3-8 IS 3ST QOL JO » JeEUS 7] Gs a ml 5 T Fer q co
oy ni aT
oot
Ndd
CPU Sheet 5 of 16 Local ADDR AUS LOCAL DATA aus
“om yt ee
3-9 =COmN, CHTR? aay COIN. ENTRY ee
‘Se ¥iNG O50IA ‘sne woo O3azA
SAT Baa WaOT
svar SE Wive BRT “yoo Waa
3-10 aint ae —t
‘ysveJoinv sin
ava <I Soe viva7uagy 1907
QSL 40 9 1098S
ndd
om
Bj SVT
wi
- ios WRG
wR She wag 30vNE ‘S06 viva Jowr
=a se waa JovAT ene viva Woot 9L 40 Z JoouS
nds 3-11
wei “douI=
3-12 9b 40 8 Je8US Ndd
‘sne Viva 39¥NT wey zeus
Bie HUT su ‘she SS3¥0OV JOWRT Aon Jom OL JO 6 89S
Ndd 3-13
3-14 QE 40 OL 1004S
ndo aie SAT WOO CIGAR
9b 40 LL YO0US
Ndod
ire
Bae VIVE Woot _ ae
a 7 = ar T = Toes PE 7 a
- wT
‘Daswvnna an.
3-16 waa TORT 9b 40 ZL 1980S
ndd
3-17 9b JO EL Joous
Ndd
3-18 9b 40 HL 1e08US
ndd
CPU
Sheet 15
3-19 of 16 SJnpuTa1 set" 3, SruevTa0 sei n
srcvs 4.7K a0FF j 19, sRoan_ac Ht ost orPsw
cokes eto. SEL LOCAL DATA BUS.
CPU Sheet 16 of 16
(a oes te NOK 7-22-4/ |275'7
sw as a slurs we U20
®
| D | Shay | as |
our} so:
| ir | f™s | S |
Bee a6
| 3\9/5 | u20 | Fasee | ute | SUS a SS aS sts | |
| : | cia | “ | rawes | ame te ice | en ac ca |
im
4s | masa, et
- “Tene *
| +5V | +5 | ‘ | us |
| TYarct] are | e | us | yt |
AS Stas ete] wate
| Or | git | nH | 7 | co | menere th |
| awe Te | ale | } | “ | irrmealy | ra |
; EH 8
| " | i | at | ||||
| —— | tla | Ps | I ne | THUSTae | wv | aay st w |
| vey | pms | na | reset | zy ee | \ | |
| Aber alt | 3 | Cn | ore | ay an | ||
| — | a | | et | | | Huis | 4 | i |
| ay, | Kau | —2l a | ||||
| Taye | Mn | [te | ||||
| nan | ex | ut | | Tee | |||
| 7 | Se | és | ; | . | - | |
| [oe a | | | | ? | ater | A | > | |
| ATECUR | 249 @ | ono | Tas | ‘Y | ||
| us | ~ | vir | . | ; | ‘sv |
1 ‘ an share Ton tae
| B | so | Dae | > | i | $ |
| x | ; | pt | ue | ||
| — | viz | be | va | _ | |
| 10 | orkin w/w $85 | : | |||
| ax | en | yew Si) cael | |||
| t— | er | ~ | . | STE oor [9 og | |
| ie | . | 5 | : | Skatihoit i HBS | |
| THC | see | | | ein 170 [1S Zeawan 3 | |||
| wo |” | iss | 4h hae |
ie yor 2a abhe Yes HERE
| an | va He | xo | |
| — | MOTE | ye HEN | + |
er Ear.
vorsaon forrats
| | | MTGHOLE MTSHOLE MTGHOLE | Sound Board |
MTGHOLE z
| A | Tod | 63 | 62 | Tot | oe | Sheet 1 of 4 |
| 7 | 7 | 7 | a * |
[ENERMATION CONTATNED. ERETQ_I5-CONETDENTIAL PROPERTY AND May nT oo AREDROR SPE SMES WER ABET EteRE SOMME PTEN CbnseRr tow TRE Comb aE RECT Ee FIRST PROJ. NO [WILLIAMS ELECTRONICS. GawES INC |R_KaRSTENs 48069" "” | IDWAY MANUFACTURING. COMPANY te en Pel HIRST USGACE 3401 N. CALIFORNIA AVE. CHICAGO IL
| - | = | TINE VIDEO SOUND GENERATOR | ||||||||||
| cite | OAT | 7a | ||||||||||
| EE | aE | CURRENT. PROJECT | SEES HESS | ||||||||||
| og | one [ET | a | rereert | as | ||||||||
| 1 | | | 2 | | | 3 | | | 4 | | | S | | | 6 | 8 | 3-21 |
Rev.
ween eed :
| ff | sees | lax 1 | rs | vant-o0T |
v1 ,
2 2: AHO im °
| z | f | sh |
a _I Ss o% 2 er mac
mm iy
| eae | v | ; |
Be 8S ste hese
i ee liad =ae a2
- - v2a >
tee severe
a
lev
u29>—+* Goons) a soo vs
lee : tay uy
nc-our
se
rewout
Hi
‘27e840-156 R1C0H= 150° , a] am a} oe ald |” J
. Sound Board Sheet 2 of 4 as2 af TREGRMATION CORTATNED BERR TS, ONE TOENTTAC PROPERTY AND MAY NOT BE.
| ve 2 | ’ | ‘ | ' | ’ | ' | ' | )SED OR DISCLOSED MA THOuT EXPRESS WRITTEN CONSENT. FROM THE COMPANY. |
| POmANT | ot | Ot uF | ce | Tyest | 5 | WILLIAMS ELECTRONICS GAMES INC. | |
| aa | st | ei° | Raat Tens___| | Aone | AIDWAY HANUF ACTURING COMPANY | ||
| see | a] ae | fara) at | TP loco syastBf[RETRTseSingby | [207M caLteomeza-ave cnteaco 1 |
ave | CURRENT PROJECT | = RE” __sia0lSt [WU wishe Sinn soo rn BE ET =|
| 2 | 3 | 6 | T | 8 |
| | 2 4 5 3-22
lec) 0. P2241 2318
pout
- zzoour
eno Vv Taw & aon
C , are ET ;
vow
| _ | A | rear | ano | new | wane |
| weer | + | eae s | v | cy | afar |
| Por | 32 | > | “o L | ‘GND | mm |
| ee | + | Tronew | , |
is AGND
B so
vont Yacv0
yy
! Fi
i jae sono
A Sound Board
ol - “wa T TON CORTATAED, HERETR_IS-GOMETDENTIAC PROPERTY pap PAL DOT 4 come TED SEL OR ET MES To Ee Z POR HIRST PROV. WOT WILLTaNs ELECTRONICS CANES THC; R._KARSTENS z MIDWAY MANUFACTURING COMPANY Bho a0 SAUTE, [stn catfowts wes cusco ae se VIDE, SQUND GENERATOR
| RK. | 5/28/91 | 40009 | AMPLIFIER |
ad SMET gg OF 16-9234 -
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Control Panel Wire Colors
Player One
Start Yellow-Green
Up (Jump) Orange-Black Down (Duck) Orange-Brown Left (Move) Orange-Red Right (Move) Orange
High Punch — Orange-Yellow
Block Orange-Green High Kick Orange-Blue Low Punch Orange-Violet Low Kick Orange-Gray Ground Black
Player Two
Start Yellow-Blue
Up (Jump) Yellow-Black Down (Duck) —Yellow-Brown Left (Move) Yellow-Red Right (Move) Yellow-Orange High Punch —_Yellow-Violet Block Yellow-Gray High Kick Violet-Black Low Punch Violet-Brown Low Kick Violet-Red Ground Black
PC Board Jumpers
CPU Board We, W8, W11, W12, W14, Wei, W22, W24, W27, W29, W380, W32, W34, W36, W39, W41, W42, W45, W47, W48, W50, W52, W55, W57, W58, W60, W62, W65, W68, W69, W71, W73, W75, W77, W80
Sound Board Wa, W3, W5, W7, W8
WARNINGS & NOTICES
Warnin
USE OF NON-MIDWAY PARTS OR CIRCUIT MODIFICATIONS MAY CAUSE SERIOUS INJURY OR
EQUIPMENT DAMAGE! USE ONLY MIDWAY AUTHORIZED PARTS.
- For safety and reliability, substitute parts and modifications are not recommended.
- Substitute parts or modifications may void FCC type acceptance.
- This game is protected by federal copyright, trademark and patent laws. Unauthorized modifications may be illegal under Federal law. This also applies to MIDWAY logos, designs, publications and assemblies. Moreover, facsimiles of MIDWAY equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with MIDWAY components.
Notice When MIDWAY ships a game, It Is in compliance with FCC regulations. Your sticker is Proof. If the sticker is missing or damaged, legal repercussions to the owner or distributor of the game may result. If your game does not contain an FCC sticker, call MIDWAY immediately.
Notice No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may be transmitted, or otherwise copied for public or private use, without permission from the publisher.
Entire contents of this manual copyright © 1992 MIDWAY Manufacturing Company, INC. All Rights Reserved.
FOR SERVICE: CALL YOUR AUTHORIZED MIDWAY DISTRIBUTOR.
MIDWAY Manufacturing Company 3401 N. CALIFORNIA AVE. CHICAGO, IL 60618