CATHODE RAY TOMES

Joust Instruction Manual For Cocktail Table Games (16P-3006-101-T) Sept 1982

Joust (Green label) (Williams, 1982) · Instruction Manual · 12 pages · 15 sections · original scan

Page 1

Sle 16P-3006-101-T Wij Uf, ‘2 September, 1982

INSTRUCTION MANUAL

FOR

COCKTAIL TABLE GAMES

including procedures for... ° operation ° auditing

  • adjustment ¢ diagnostics

FOR SERVICE...

NOTE NEW TOLL-FREE TELEPHONE NUMBERS: ELECTRONICS, INC. 3401 N. California Ave. 800-621-1253 Chicago, IL 60618 Cable Address: WILCOIN, CHICAGO IN ILLINOIS CALL: (312) 267-2240 800-572-1324
Page 2

ROM SUMMARY

ROMPART NO.DESCRIPTION
JOUST 1AA-5343-09961-APROM, 4Kx8, YELLOW LABEL
JOUST 2AA-5343-09962-APROM, 4Kx8, YELLOW LABEL
JOUST 3AA-5343-09963-APROM, 4Kx8, YELLOW LABEL
JOUST 4AA-5343-09964-APROM, 4Kx8, YELLOW LABEL
JOUST 5AA-5343-09965-APROM, 4Kx8, YELLOW LABEL
JOUST 6AA-5343-09966-APROM, 4Kx8, YELLOW LABEL
JOUST 7AA-5343-09967-APROM, 4Kx8, YELLOW LABEL
JOUST 8AA-5343-09968-APROM, 4Kx8, YELLOW LABEL
JOUST 9AA-5343-09969-APROM, 4Kx8, YELLOW LABEL
JOUST 10AA-5343-09970-APROM, 4Kx8, YELLOW LABEL

JOUST-11A——-—-—.-.- A-5343-09971-A-—- PROM; 4Kx8, YELLOW-LABEL ~~

JOUST 12AA-5343-09972-APROM, 4Kx8, YELLOW LABEL
Decoder ROM 4A-5342-09694PROM, 512x8

(Horizontal)

Decoder ROM 6A-5342-09821PROM, 512x8

(Vertical)

Video Sound ROM 4A-5343-09973ROM, 4Kx8

Special Chip 1 A-5410-09911 Special Chip

POWER TURN-ON

CAUTION - This game must be plugged into a properly-grounded outlet to prevent shock hazard and to ensure proper game operation. DO NOT use a “cheater” plug to defeat the ground pin on the line cord, and DO NOT cut off the ground pin.

WHEN THE GAME IS FIRST TURNED ON it produces a sound. Simultaneously general illumination should come on and a moment later a scanning “rug pattern” indicating the RAM test should appear on the screen. Next the rug should become stationary as the ROM test is performed. In a correctly-running game the rug pattern will be followed by the message “INITIAL CHECKS INDICATE ALL SYSTEMS GO”, If RAM or ROM failure messages come up on the screen instead, refer to Power-Up Tests. in TROUBLESHOOTING PROCEDURES.

GAME OPERATION

GAME START - Insert coins; a random sound is produced and credits are displayed on the CRT. With two or more credits displayed, pressing 2-player start initiates a 2-player game where each player gets five* mounts (turns).

*adjustable feature

Page 3

PLAYER CONTROLS

THE JOYSTICK sends the gladiator and his ever-stalwart mount (ostrich or stork) boldly to the left or to the right.

THE FLAP BUTTON causes the hero’s mount to spread its robust wings.

GAME PLAY

AT SOME FAR-DISTANT TIME two fantastic gladiators meet and square off for battle. Each is mounted on a fanciful bird of prey (ostrich or stork) whose wings can carry it from the clifftops to the mouth of the abyss and hopefully back... or the bubbling lava below will increase its toll. :

While your mount is a skilled flyer, your opponent is a shrewd gladiator. You must prove you are his better. Stealthily you must pilot your mount above him, and cleverly you must stalk him... to strike at the moment in which he least suspects you! And always remember this rule: In every joust, the highest lance wins.

Of course your opponent will resist your attempts, all the while pursuing his own designs against you. Each gladiator has five* mounts. Every time you’re toppled, you must mount a new bird for the next joust. The gladiator who scores the most dismountings is the winner.

YOUR PATH MAY SEEM CLEAR and your work cut out, but just then a flock of vicious Buzzard-Riders will ambush you! Ruthless even as they are dismounted, these wily Buzzard-Riders instantly lay their eggs. You must pick up the eggs or they will soon hatch into even more persistent and antagonistic foes!

Fortunately at 20,000* points (should you make the grade) you will be awarded another bird to mount against the loyal opposition.

Joust is-designed-for-either.one-or-two-players.

HIGH SCORE SIGNATURE

Select letters with the joystick. Push right to move forward through the alphabet; push left to move backward. Then push the FLAP button to lock in the letter.

BOOKKEEPING AND EVALUATION TOTALS In Game-Over Mode, open the coin door or tabletop, set the AUTO-UP/MANUAL-DOWN switch to AUTO-UP, and depress the ADVANCE switch. (See Figure 1.) The bookkeeping and evaluation totals appear on the CRT as in Figure 2.

O @O HIGH MANUAL- ADVANCE. SCORE DOWN RESET

Figure 1. Tabletop Button Switches

*adjustable feature

Page 4

CLEARING BOOKKEEPING TOTALS

  • Depress ADVANCE to display Game Adjustments.
  • Operate PLAYER | joystick to position cursor on CLEAR BOOKKEEPING TOTALS.
  • Push PLAYER 2 joystick.
  • Depress ADVANCE.

BOOKKEEPING TOTALS

LEFT SLOT COINS CENTER SLOT COINS RIGHT SLOT COINS PAID CREDITS FREE MEN TOTAL TIME IN MINUTES TOTAL MEN PLAYED TOTAL SINGLE PLAYER TOTAL DUAL PLAYER TOTAL CREDITS PLAYED AVERAGE TIME PER CREDIT

Figure 2. Bookkeeping Display

GAME ADJUSTMENTS

In the Game-Over Mode open the coin door. With the AUTO-UPIMANUAL-DOWN switch set to AUTO-UP, depress the ADVANCE switch twice to cause a CRT display as shown in Figure 3. Select the function you wish to change by moving the PLAYER 1 joystick (push right to move arrow down, left to move arrow up). Then, making sure the coin door is open, push the PLAYER 2 joystick right to increase or left to reduce the value of the selected function.

The number of turns (men) per |-credit game can be set anywhere from 1 to 99 (5 recommended). Difficulty is factory-programmed at 5 (moderate). It can be custom programmed (0-9, with 9 conservative) as desired.

Game Pricing is selected with standard settings or with custom settings as shown in Tables 1 & 2. Table | lists some. common pricing schemes and directs the reader to the proper entry in Table 2, which shows what the CRT display should look like to accomplish the desired pricing. Note that free play can be elected by entering the code number 9 at the PRICING SELECTION function (see Tables | and 2).

For standard settings you need change only the PRICING SELECTION. For custom settings, first set PRICING SELECTION to zero and then set the remaining values according to Table 2.

Page 5

GAME ADJUSTMENTS

EXTRA MAN EVERY 20000 MEN FOR 1 CREDIT GAME 5 HIGH SCORE TO DATE ALLOWED YES PRICING SELECTION 1/QUARTER 4/DOLLAR LEFT SLOT UNITS CENTER SLOT UNITS RIGHT SLOT UNITS UNITS REQUIRED FOR CREDIT UNITS REQUIRED FOR BONUS CREDIT MINIMUM UNITS FOR ANY CREDIT DIFFICULTY OF PLAY LETTERS FOR HIGHEST SCORE RESTORE FACTORY SETTINGS CLEAR BOOKKEEPING TOTALS HIGH SCORE TABLE RESET AUTO CYCLE SET ATTRACT MODE MESSAGE SET HIGHEST SCORE NAME

USE ‘PLAYER 1 MOVE’ TO SELECT ADJUSTMENT USE ‘PLAYER 2 MOVE’ TO CHANGE THE VALUE PRESS ADVANCE TO EXIT

Figure 3. Game Adjustments Highest Score Signature The number of letters allowed the highest-scoring player for entering his name can be varied from 3 to 20 and is recommended as 3. If objectionable words are entered as the signature name, you can change the lettered entry leaving the highest score the same. See Setting Highest Score Name. Restore Factory Settings

  • Position the cursor on RESTORE FACTORY SETTINGS.
  • Push PLAYER 2 joystick to right.
  • Depress ADVANCE switch twice. Resetting High Score Table
  • Position the cursor on RESET HIGH SCORE TABLE.
  • Push PLAYER 2 joystick to right.
  • Depress ADVANCE.

2. Push PLAYER 2 joystick to right ane Attract Mode Message Push PLAYER 2 joystick to right

Position the cursor on SET ATTRACT MODE MESSAGE. Push PLAYER 2 joystick to right. Depress ADVANCE. Enter up to two lines of your message following instructions on the screen. Depress ADVANCE to terminate process. vaeEe

NOTE: To restore the Williams attract mode message, perform steps | through 3 and then turn the game OFF and back ON. Setting Highest Score Name
  • Position the cursor on SET HIGHEST SCORE NAME.
  • Push PLAYER 2 joystick to right.
  • Depress ADVANCE. 4, Enter new signature; depress ADVANCE to terminate process.
NOTE: An alternate, simpler method enters the factory highest score signature. In the Game Over mode, hold HIGH SCORE RESET depressed. After a few seconds a sound is produced and the factory highest score signature has been activated.
Page 6

Table 1. Pricing Schemes

TABLE 2 COIN DOOR STANDARD SELECTION/

MECHANISMCREDITS/MONEYCUSTOM KEY
| Twin Quarter1/25¢ S/$1A
Quarter, Dollar, Quarter2/50¢ 5/$1B

1/25¢ 4/$1 3 2/50¢ 4/$1 Cc 1/S0¢ 3/$1, 4/$1.25 D 1/50¢ 3/$1, 7/$2 E 1/50¢ 3/$1, 6/$2 1 1/50¢ 5

IDM, 5DM1/1 DM, 6/5 DM2
20-Cent, 50-Cent1/20¢ 3/50¢F
1 Franc, 5 Franc1/2F, 3/5F only4
25 Cent,1/25¢ 4/1G6
1 Guilder1/25¢ SAGG
5 Franc,I/SF, 2/10FT
10 FrancV/10F8
I Franc, 2 Franc2/1F, 5/2F2

100-Lire;-200-Lire 1/200-kire —-—-- 8 a

Twin CoinV/1 Coin3

1/2 Coins 5 1/3 Coins, 2/5 Coins H

1 Unit, 5 Unit1/2, 3/54

W/, S/S I 1/3, 2/5 J

FREE PLAY—9

Table 2. Pricing Settings

CUSTOM KEY DISPLAY FUNCTIONS STANDARD SELECTION A|B/C/D/E|F/G/H/| I] J Pricing Selection 1)2/3/4/5/6|}7|}8|/9;/0/0;/o0;o;o0;olo;ojolo

Left Slot units1/6;ryryt}ryrprlaryryr}1]3}i2}6}i1}2y;aife2

Center Slot units 4/0] 4/16/4/0)/0/0)4|4] 4) 4/12/48] 0]}0]o};o]0

Right Slot unitsTyr}i}eyr}4)2y;2}rsafafa)3 yizsis}4}2]5]10
Units per credit2;1}1;2/2]1;172}a]rfrprl4}iapstiysfays

Units required for bonus credit | 4} 0/0/0/0/0/0]0|0/)4]4!0/15]96]0/4]o]olo Minimum units for any credit | 0|0/0/0/0/0/0/0]0/0|/2/2]/0/24/0/o0lo]o}o

Page 7

TROUBLESHOOTING PROCEDURES

Certain types of game malfunctions may inhibit the game's diagnostic with Power-Up and continues until Game Over Mode. All proceor display faculties. Troubleshooting procedures for most of these dures can be performed with minimal test equipment or merely by Fa types of malfunctions as well as malfunctions that permit. self- observing the game itself. diagnosis are covered below. Our troubleshooting algorithm begins

POWER-UP TESTS

NO GENERALNO INITIAL VIDEOCHECKING POWER
ILLUMINATION(RUG PATTERN)SUPPLY BOARD

eet)

(1) Check fuse F2 on power supply board.(1) Open component door.(1) Swap power supply board with one from
(2) Check for proper installation of jumpers(2) Press reset button on CPU Board.known-good game.
WI, W2, W3 and/or resistor R27. (Some |(3) Try RAM and ROM tests (sce below).(2) If game plays, problem is on power sup-

machines MAY NOT have an R27. Refer to ply board. your drawing set.) (3) If game doesn’t play, check power trans-

  • Check 4P1/J1, 4P3/13, 6P2/J2 and 6P3/ Former wit salieneten

(4) Ifall the above don’t turn up the problem,

check power supply board.

B (4) If known-good power supply is unavail- “ . able for tests above, check +5V, —SV and

  • Ifall the above don’t turn up the problem, + 12V outputs on power supply in game. Each check power supply board MUST BE within 2% of rated output with less than 0.1% AC hum. 2 | MORE POWER-UP TESTS

ROM BOARD ROM BOARD LEDS LEDS IDENTIFY RECOGNIZE BAD CHIPS CONDITION REMEDY

GENERAL — | “0” means“all=(1) Scanning rug patternIf any video (See left) is missing or
power-up tests(2) stationary rug patternerror message is displayed, proceed to
passed(3) “INITIAL TESTS INDICATE ALLDiagnostic Mode tests.

SYSTEMS GO”

  • Game-Over Mode
CMOS (See“OQ” means tests=“HIGH SCORE TABLE RESET”

Appendix A) | passed “BOOKKEEPING TOTALS CLEARED” . “ADJUSTMENT FAILURE” “RESTORE FACTORY SETTINGS BY OPENING FONT DOOR OR TABLETOP AND TURNING GAME ON AND OFF”

  • Open tabletop and turn power off and on.

“0” means tests “FACTORY SETTINGS RESTORED” passed

BATTERY“0” means testsad“HIGH SCORE TABLE RESET”(1) Open tabletop and turn power off
  • Press ADVAN! return to Game-Over Mode.
(Seepassed“BOOKKEEPING TOTALS CLEARED”and on. Or: press ADVANCE. In either
Appendix A)“ADJUSTMENT FAILURE”case, game should return to Game-Over

7 “RESTORE FACTORY SETTINGS Mode. BY OPENING FONT DOOR OR TABLETOP | (2) Check AA alkaline cells on CPU AND TURNING GAME ON AND OFF” Board.

  • If problem persists, proceed with CMOS RAM test by putting the game into its Diagnostic Mode (see SELF-DIAGNOSTICS). ics),
MEMORY“OQ” means tests“HIGH SCORE TABLE RESET”(1) Making and breaking tabletop
PROTECTpassed“BOOKKEEPING TOTALS CLEARED”interlock switch, check with VOM and
INTERLOCK“ADJUSTMENT FAILURE”replace if faulty.
(See“RESTORE FACTORY SETTINGS(2) Replace if faulty: Memory protect

Appendix A) BY OPENING FONT DOOR OR TABLETOP | gates 6E, IC1, Ql, or CMOS RAM IC. AND TURNING GAME ON AND OFF”

SPECIAL“Q” means tests| —(1) scanning rug pattern(1) Turn power off.
CHIPpassed(2) blank screen instead of “INITIAL TESTS | (2) To find bad chip, replace 2 special

INDICATE ALL SYSTEMS GO” chips one at a time with known good

  • high score table with no scores chips.
  • intro blank or program crash (3) Turn machine on after each replacement and run through Power-Up
Page 8

+5VDC ADJUSTMENT (R10 & R24) Before adjusting the voltage output, always check at the output of the supply for AC hum. This hum should never tise above .005V on the +SVDC supply. If it does, consult your schematic drawing set for proper DC voltages throughout the circuit. Test for these with the DC setting of your multimeter. Make a second check using the AC setting. Pay particular attention to readings at TPS (top of capacitor C10). If the voltage here is low (less than + 1IVDC) or if you find excessive ripple (more than 700mVrms), replace the capacitor.

Table 3. Voltage Adjustments to +5VDC Power Supply

WHICH RESISTORS SUPPLY

HAS...neitherRIO onlyR24 onlyR24 & RIO

TO INCREASE VOLTAGE IF remove R10 or

UNDER 4.95VDC...add R24.add R24_remove R10

TO DECREASE VOLTAGE IF remove R24

OVER 5.25VDC...add RIO=or add R10remove R24

SELF-DIAGNOSTICS

subsequent test).

  • Depress ADVANCE.

| displayed on the CRT.

  • To terminate the Auto-Cycle test, turn the game OFF and ON.

LEGEND: FIRST DESIGNATION (3K) IS CIRCUIT BOARD GRID REFERENCE. DESIGNATION IN PARENTHESIS DENOTES BANK NO. (1-3) AND CHIP NO. (1-8).

BANK 3 BANK 2

2K(21)

2M(23)

20(25)

2a(27)

2R(28) WEBBBEEE BANK 1 If RAM or ROM failure messages are displayed on the CRT after the “rug pattern,” proceed with self-diagnostics. Self-diagnostic procedures are controlled by the AUTO-UP/MANUAL-DOWN and ADVANCE switches under the tabletop. (See'Figure 1.) Set the AUTO-UP/MANUAL-DOWN switch to the MANUAL-DOWN position and depress the ADVANCE pushbutton. The game is now in its Diagnostic Mode and a ROM test is performed. With ROM test results present on the CRT display, set AUTO-UP/MANUAL-DOWN switch to the AUTO-UP position. Depressing the ADVANCE pushbutton initiates the RAM test. Further tests (CMOS, sound, switch, color RAM, and monitor test patterns) are encountered one after the other as the ADVANCE pushbutton is depressed (once more for each

AUTO-CYCLE-MODE-=From the-color-bar-pattern-(or-Game-Over with the switch sét to AUTO-UP) depress ADVANCE two times to display GAME ADJUSTMENTS.

  • Position the cursor on AUTO CYCLE with the PLAYER 1 joystick and push the PLAYER 2 joystick right.
  • The system will now sequence through ROM, RAM, and CMOS RAM tests repeatedly. The tabletop must be open during the Auto Cycle test. If an error is detected, the test is terminated and the failure indication is

us INTERFACE. SP} | INTERBOARD CONNECTOR

Figure 4, RAM Location and Numbering on CPU Board Oy

Page 9

TROUBLE DIAG SHOOTING PROCEDURES: NOSTIC MODE TESTS

ROM BOARD LEDS RECOGNIZE CONDITION ROM BOARD LEDS IDENTIFY BAD CHIPS VIDEO REMEDY

“2” means ROM error 2-digit ROM chip no.

“1” means RAM error Bank no. first... then chip no. in bank (see figure 4) “ROM ERROR” and ROM chip no.

  • Turn power off.
  • Replace suspected chip.

“RAM ERROR” followed by RAM bank no. and chip no. (Note: with multiple RAM failures this display may not appear)

  • Check for these normal voltages on indicated RAM chip: ~Sipin 1, + 12/pin 8, +5/pin 9.
  • Turn power off.
  • Replace suspected chip.
  • With multiple RAM failures always check power supply. See POWER-UP TESTS.

CMOS (see appendix A) “3” means CMOS RAM error

= a “CMOS RAM ERROR OR WRITE PROTECT FAILURE”

Tests 4 and 7 provide sequential subtests. To stop automatic cycling set switch to MANUA MANUAL-DOWN to step through subtests. LED indications are not made for these tests.

  • With power off, check pin 18 of CMOS RAM for 3.2VDC minimum. If present, replace CMOS chip IC. If absent, replace AA alkaline cells.
  • With new alkaline cells and power off, check for 3.2V minimum at pin
  • If still absent, replace diodes D9 and D10.
  • Upon power-up and reentry into diagnostics if CMOS error message persists, check CMOS RAM memory protect and address decoding circuits ‘with-a-logic-probe:

L-DOWN. Depress ADVANCE in

n |

yund Board

TEST & PROCEDURESVIDEOREMEDY OR ADJUSTME!
SOUND“SOUND LINE 1”MISSINGCHECK
(Test 4)“SOUND LINE 2”12P4/10P3 pin 3
“SOUND LINE 3”22P4/10P3 pin 2
7“SOUND LINE 4”32P4/10P3 pin 5
“SOUND LINE 5”42P4/10P3 pin 4
“SOUND LINE 6”52P4/10P3 pin 7
(These appear one at a time.)62P4/10P3 pin 6

all perform St

Diagnostics (see below)

NOTE: If any two sounds are the same, check for a short between the select lines with the same sound.
SWITCHCRT indicates AUTO-UP closed and any stuck switches. CRT(1) ROM BOARD SWITCH STUCK:
(Test 5)Display for Each SwitchDisconnect 2P3.
  • Set switch to MANUAL-DOWN and clear any stuck switches
  • CRT should indicate no switches closed.
  • Operate switches and check for display of switch name.
  • INTERFACE BOARD SWITCH STUCK: Disconnect 3P2 or 3P3. ROM Board Interface Board

UNDER TABLETOP: ON COIN DOOR:

ADVANCE 1-PLAYER START. AUTO-UP 2-PLAYER START HIGH SCORE RESET ON PLAYER PANELS: ON COIN : MOVE UP 1 & 2 LEFT COIN MOVE DOWN | & 2 MOVE LEFT J & 2 MOVE RIGHT 1 & 2 FLAP 1 & 2

  • ROM BOARD SWITCH DOES NOT OPERATE: Ground corresponding pin of 2P3.
  • INTERFACE BOARD SWITCH DOES NOT OPERATE: Ground corresponding pin of 3P2 or 3P3. (SYMPTOM REMAINS SAME ... ROM Board or Interface Board faulty.
  • SYMPTOM CLEARS UP .. Problem is in switches or wiring.
Page 10

MORE DIAGNOSTIC MODE TESTS

TEST & PROCEDURES VIDEO SEQUENCES | REMEDY OR ADJUSTMENT COLOR RAM REPLACE RAM IB | REPLACE RAM 2B

(Test 6)j,'
Note that a blank sequence or two sequences with thesjht Roepee oy dmagenta band

same shade indicate a faulty 1A flip-flop, 1B RAM, 2B 7 FY Resin oscar! ban :

RAM, or a failure in the color analog circuit. Check aT Teen or gray Dan

voltages on QI (green transistor), Q2 (red transistor) and4 light green screen | yellow bandcyan band

Q3 (blue transistor). During the eight full-screen color tests, the base voltage (center pin) on each transistor should vary between 3.8V (brightest color) and 4.4V (no S green screen 6 dark green screen

color).7 light blue screenmagenta bandtoo-light or too
,8 blue screen-dark blue or

Color RAM Check | gray band CRT through 8

io lors, 2 a were4 light green screen | green banddark green band

r gray band

  • Thick vertical band or gray ban indicates color RAM fault. 5 green screen light green band dark green band or gray band

6 dark green screen gray band MONITOR Aids you in setting up

& COLORcross hatch patternvertical and horizontal

RAM linearity, convergence, and (Test7) + — focus: —

red screen Aids you in optimizing green screen color purity. blue screen color pattern

|color barsIf color RAM test 6
i+ double-widthindicates no faults,
I+ half-widthsymptoms at left suggest a
|Color Bar Pattern* transposed.fault in 1A, 1B, 2B or 2C
I* missingchips.

} i

Ss

Page 11

SOUND BOARD DIAG IOSTICS

SYMPTOM TEST & PROCEDURES MISSING SOUNDS; CI CHECK SOUND-SELECT INPUTS NO SOUND (1) Turn power on,

  • Depress DIAGNOSTIC pushbutton on bottom of Sound Board, Sounds may be produced now even though absent in Diagnostic Mode Test 4. If you hear game sounds, proceed with this checkbox. If not, go ahead to POWER SUPPLY checkbox below. _
qlTOOLCONDITION & REMEDY

Sound Board connector 10P3/13-1__| logic probe (game on and in Test 4) | » PULSING-proceed 106 *LOW-check jacks, foils | + STILL LOW-perform ROM BOARD checkbox below

SRI DIP resistors R3-R9VOM-reading ohms (game off)* ALL 4.7K-proceed
  • ANY OPEN-replace SRI
C3-€9VOM-reading ohms (game off)* ALL OKAY-proceed

_ + ANY SHORTED-replace bad IC5-1, 1C7-14 logic probe (game on and in Test 4) | + HIGH-proceed (power pins) + LOW-replace C19 (ICS) or C21 (IC7) + STILL LOW-replace bad IC IC5-2, 4, 6, 10, 12, 15; 1C7-4, 6 | logic probe (game on and in Test 4) | + PULSING-proceed + LOW-replace chip IC10-18 and 19 logic probe (game on and in Test 4) | + PULSING-proceed (PIA) + LOW-lift C20, retest + PULSING NOW-replace C20 + STILL LOW-replace IC6, retest IC10-10 to 17 logic probe (game on and in Test 4) | * PULSING-proceed (PIA) + SOME LOW-replace IC + ALL LOW-lift C31, retest + PULSING NOW-replace C31 + STILL LOW-replace IC SOUND WHEN CO CHECK ROM BOARD OUTPUTS DIAGNOSTIC (J) If you hear game sounds, disconnect and then reconnect Sound Board connector 10P3/J3. PUSHEUT TON PRESSED, (2) You should hear one or more game sounds. If so, put game in Diagnostic Mode ‘Test 4 and procced with this DIAGNOSTIC MODE TEST 4

NO SOUND

STILL NO SOUND checkbox. If not, go ahead to POWER SUPPLY checkbox below.

TEST TOOL CONDITION & REMEDY

ROM Boafd connector 2P4/14-3 logic probe (game on and in Test 4) | + PULSING-repair cable to Sound Board to 6 + ANY LOW-repair jack or foil, proceed

OC DIP resistors 2 to 6VOM-reading ohms (game off)* ALL 4.7K-proceed

+ ANY OPEN-replace 0C

€26-39VOM-reading ohms (game off)+ ALL OKAY-proceed
  • ANY SHORTED-replace bad ICIC-10 to 15 (PIA) logic probe (game on and in Test 4) | + PULSING-proceed
  • SOME LOW-replace IC
  • ALL LOW-lift C23, retest + PULSING NOW-replace C23
  • STILL LOW-replace IC OO CHECK ON-BOARD POWER SUPPLY
  • With power off, test for fuse continuity at Fl and F2.
  • With power on, check for +12V unregulated DC at TP1 and at pin 5 of ICI.
  • Now check for +5V regulated DC between TP4 and TP3. If voltages are absent or low, turn off game and lift one pin of filter capacitors C25, C26 and C27.
  • Check each with ohmmeter for possible shorts.
  • If capacitors are good and unregulated voltages test okay but you're missing +5V, replace regulator chip (IC8). CO CHECK AUDIO (ANALOG) SECTION
  • Turn power on; turn up volume control. Momentarily place powered-up AC soldering pencil on final amplifier’s input pin (ICI, pin | or 10P4, pin 2). If you hear low hum, audio IC, volume pot and speaker are okay.
  • Repeat test at Q2 emitter. If you hear hum, analog section is okay. Step (1) will also work if you simply touch amplifier’s input pin. However ouput level of hum will be much lower than with soldering iron. DO NOT use a soldering pencil of over 40 watts. Cordless models will NOT work here. MISSING SOUNDS; NO SOUND (1 CHECK SOUND ROM 12 AND RELATED CIRCUITRY
  • Is Jumper WI connected? IT SHOULD BE on all Joust games, or sound signals from the D/A converter (IC13) will never arrive at input of impedance-matching transistor Q2.
  • Turn power on.
  • If you have no game sounds but power supply tests show normal voltages and no ripple on +5V, check crystal clock circuit, Using DVM or logic probe, test for pulsing AC across crystal. If clock signal’s absent, replace crystal and associated capacitors.
  • Turn power off.
  • Swap sound ROM (IC12) and then microprocessor chip (IC9) with known-good chips.
  • Power-up and test Sound Board after each swap by pushing DIAGNOSTIC button,
Page 12

CMOS RAM Data Test Protocol

The first sub-test of the CMOS RAM data is that of the ATTRACT MODE MESSAGE checksum. If the test does not pass, the factory ATTRACT MODE MESSAGE is restored. Next, the game adjustments are checked and restored to factory settings if an error is found. If game adjustments are found intact, the high score table is checked for any bad entries. Bad entries are replaced with a score of 4,000 points and no initials. If all entries check, the game returns to the Game Over Mode.

If game adjustments are restored to factory settings, the AUDIT TOTALS are checked. If 5 or more audit digits are other than 0-9 (that is hexadecimal A through F) all audit totals are cleared. This is followed by a check of the high score table and the table is reset to factory settings if errors are found. Finally, game adjustments are rechecked and either OPEN COIN DOOR or FACTORY SETTINGS RESTORED is displayed. With the former, open the coin door and turn the game OFF~and~ON~and “then” FAC- TORY SETTINGS RESTORED will be displayed. Return to game over by depressing the ADVANCE pushbutton or by turning the game OFF and ON a second time. APPENDIX A

ATTRACT MODE MESSAGE?

RESTORE FACTORY MESSAGE

RESTORE FACTORY SETTINGS

RESET HIGH SCORE TABLE To FACTORY SETTINGS,

Fa

“OPEN COIN DOOR” DISPLAYED

‘OPEN COIN DOOR POWER OFF AND ON Fa.

BAD ENTRIES REPLACED WITH 44,000 AND NE INITIALS

INITIAL TESTS: INDICATE ALL SYSTEMS GO’ DISPLAYED

“FACTORY SETTINGS RESTORED" DISPLAYED

“Warning: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. As temporarily permitted by regulation it has not been tested for compliance pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.”