Strider
Strider (USA, B-Board 89624B-2) (Capcom, 1989) · Manual · 20 pages · 18 sections · original scan
x a =a on 0 i Of <{ Sez
THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
CAPCOM, USA INC.
INVITES YOU TO USE
OUR TOLL FREE NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER CAPCOM GAME YOU NOW HAVE ON LOCATION. PLEASE HAVE GAME SERIAL NUMBERS AND CABINET NUMBERS READY.
CALL US FOR PROMPT, COURTEOUS
ANSWERS TO YOUR PROBLEMS.
California Only (800) 222-0928 Continental U.S. (800) 843-4632 Direct Number (408) 727-0400
WARRANTY, REPAIR AND RETURN POLICY
REPLACEMENT PARTS: CAPCOM USA maintains a stock of replacement parts for our products. When placing an order for parts, please supply a complete description of the item, quantity required, PO. number, and shipping information. We attempt to ship orders the day they are received, orders received after 12:00 noon will ship the following work day. We do not have a minimum order requirement at this time, however we certainly appreciate your efforts to consolidate your orders whenever possible. Payment Terms are NET 30.
RETURN MATERIAL AUTHORIZATIONS: Material can be returned to CAPCOM USA only in the following situations:
- Parts, return for credit. A parts order was processed incorrectly, ie; wrong items were shipped, wrong quantity was shipped, etc.
- PCB, Repair & Return. A PCB requires repair by CAPCOM USA's technical staff.
- PCB, Return for Credit. A PCB is being returned for credit to satisfy an Advance Exchange transaction.
- Other, parts are being returned for engineering analysis, etc., only with prior consent of Customer Service or Sales department. To obtain a Return Material Authorization, please contact CAPCOM USA's Customer Service department. Describe the transaction and request an RMA number. The outside of the package must be clearly marked with the RMA number. Packages not displaying an RMA number will be returned un-opened.
REPAIR & RETURN PCBs: CAPCOM USA staffs qualified technicians to assist your repair department. In the event you have a CAPCOM USA PCB that is out of warranty and requires repair, we can provide repair services to you. When requesting an RMA number for a Repair & Return, indicate the type of PCB being returned for repair, PO. number, and shipping information. Repairs will be processed within 1 working day of receipt of defective item. Labor charges are $40.00 per hour plus parts. If the initial estimate indicates that the labor will exceed 1 hour, our technicians will call and request authorization to continue the repair. Payment Terms are NET 30.
WARRANTY REPAIRS: During the initial 90-day warranty, customers who’s accounts are current are eligible for an Advance Exchange PCB. When calling for an Advance Exchange PCB, please supply a complete description of the item needed, game serial number for warranty verification, PO. number, in shipping information. You will be issued an RMA number for the return of the defective PCB. Terms for Advance Exchanges are NET 15. If the defective PCB is not returned within 30 days, no additional Advance Exchanges will be issued until the offending PCB is returned, or the invoice is paid in full. If the PCB is not returned until after 90 days, the warranty will be voided, and the customer will be liable for all repair charges. It is our goal to constantly improve and better our services to you. Your cooperation with the above stated policies will help us greatly to reach this goal. If you have any comments or questions, please telephone our Customer Service department. We will make every attempt to tailor our services accordingly.
Before You Get Started...Stop!
Does your new game package include all listed parts? (Is it complete?)
. Is the game you have chosen to transform able to supply all the required voltages for the new game?
. Is the monitor configuration compatible? In most games it is rather difficult to change the monitor from a vertical mount to a horizontal mount. We recommend you choose a game cabinet with the same mount as your new game requires.
Do you have the necessary tools? (See the recommended tool list)
Installing and Servicing Your
New Game Package
Table of Contents
Power and Monitor Requirements.............. 00.0000: cece eee eee 2 New Game Package Contents............... 00.0 cece cece teens 2 Recommended Tools and Supplies............ 0.00.00. eee eee ee 3 Dip Switch Tables... 00.0.0... ccc cette teen eee 3,4
Game Description......... 00.0... eee e eens 5 Installation Procedures. ....... 20... 00.0. cece eee 6 Helpful Hints... 0.0.0... eee n eee 12 Control Panel Positioning..... 2.2.00... 0.0 ccc 13
Main Harness Connections................ 000. eee eee 14 Warranty Registration Card.......... 0... eee eee 15
POWER REQUIREMENTS MONITOR REQUIREMENTS
Horizontal Mount Raster Scan Negative Composite Sync
NEW GAME PACKAGE CONTENTS
1 Main Printed Circuit Board (PCB) 1 Control Panel Overlay 1 Set Legs, Bolts, & Spacers 1 Plex Control Cover 1 Connecting Wire Harness 1 Set Side Graphics 1 Eight-Way Joystick 1 Monitor Card 6 Player Button Assemblies 1 Service and Installation Manual 1 Marquee
Recommended Tools and Supplies
CAPCOM new game package. Phillips and Slot Screwdrivers Painting Supplies Socket Set (if you do your own painting) Wire Cutters and Strippers Paint Brush and Paint Pliers or Channel Locks (don’t forget the primer) Planning and Careful Thought Paint Roller and Pan Electric Drill Sand Paper 3/30", V4", 7—” Drill Bits Putty Knife and Wood Putty V4" Plex Bit Staple Gun and Staples 13/46” Chassis or Sheet Metal Punch Soldering Iron and 60/40 Resin Core Solder 11/4,” Plex Hole Saw Vacuum Cleaner Glass of Water and a Snack Assorted Fastening Hardware Small File Shrink Tubing: 3/32”, %/8", 3/16” Razor Knife and Sharp Blades Masking Tape Straight Edge 31/2" OR 4” Wire Ties Spray Window Cleaner and Rags (baby diapers work GREAT!)
Dip Switch Tables
Optimize Your Profits
Thorough Research shows that two and a half minute games both satisfy players and also keep the quarters flowing. If games aren’t running about two and a half minutes long, then collections probably aren't at their peak. You'll want to tailor your game to your location. The trick is to adjust a few DIP switches. (See the chart in this book.) It’s easy!
DIP SW (A)
DESCRIPTION COIN 1 CREDIT
COIN 3 CREDIT 1 COIN 2 CREDIT
COIN 4 CREDIT 1 COIN 6 CREDIT 2 COIN 1 CREDIT 3 COIN 1 CREDIT 4 COIN 1 CREDIT 1 COIN 1 CREDIT 1 COIN 2 CREDIT 1 COIN 3 CREDIT 1 COIN 4 CREDIT 1 COIN 6 CREDIT 2 COIN 1 CREDIT
Computer aided difficulty adjustment. Strider contains 16 internal level settings. 1 being most easy and 16 being most difficult. 8 external adjustable difficulty settings set the internal automatic adjustments. Example: Very easy external starts at level 3. If player is still playing after 1 minute, 30 seconds, internal difficulty is raised to level 4 and increases every 10 seconds. If player dies before 1 minute, 30 seconds; level is automatically dropped to internal difficulty setting 2. Goes then for 1 minute, 30 seconds, then raises to internal setting 3 again.
DIP SW (B)
DESCRIPTION 4 5 6 Z 8 VERY EASY
DIFFICULTY NORMAL II |O |T\M |0 |O |w |>
VERY DIFFICULT Starts at level 3+ Starts at level 3+ Starts at level 6+ Starts at level 6+ Starts at level 6+ Starts at level 6+ Starts at level 9+ Starts at level 9+ 1 min, 30 sec, then every 10 sec. 1 min, then every 15 sec. 1 min, 30 sec, then every 10 sec. 1 min, then every 15 sec. 1 min, then every 10 sec. 45 sec, then every 15 sec. 1 min, then every 10 sec. 45 sec, then every 15 sec. 2 COINS/PLAY NO OFF 1 COIN CONTINUE YES ON "A) BONUS (B) (EXTEND) (C)
*(A) 30,000, 60,000, EVERY 70,000 (C) 20,000, 50,000, EVERY 70,000
DIP SW (C)
ITEM DESCRIPTION (B) 10,000, 30,000, EVERY 30,000 (D) 40,000, 70,000, EVERY 80,000
NUMBER OF PLAYER
SCREEN
FREE PLAY
SCREEN STOP”
SOUND DURING * YES DEMONSTRATION NO YES CONTINUE NO
GAME MODE __| TEST MODE TEST MODE
*RECOMMENDED SETTING ‘‘B”’ *FACTORY SETTING
Master the Art of Ninjutsu with Capcom’s new smash hit, STRIDER. You control the action of this futuristic Ninja from the year 2048 A.D. as he battles his way from the rooftops of Moscow through the jungles of the Amazon to the skies over planet Earth. Strider, with his totally unique acrobatic flips, incredible climbing ability, and amazing gameplay, will keep your players filling the cashbox. And the graphics are so sharp and colorful, you'll think you’re watching an animated cartoon! This is no ordinary video game, and Strider is no ordinary hero. Try STRIDER yourself and discover if you have what it takes to be the Master of Ninjutsu!
Installation Procedures
Something to Think About Your final product will be a new game. You have made a wise decision to transform a game that has seen better days in the all
Let’s Get Our Hands Dirty
Preparing the Original Game for the New Game Remove the following:
| 1. | Main Logic Board(s) | 4. | Monitor Bezel |
| 2. | Control Panel | 5. | Marquee |
| 3. | Monitor Plexiglass | 6. | Graphics |
| would recommend painting your cabinet to give it a fresh new look. (If it is geographically inconvenient to make use of our facilities, you may consider having an auto body shop take care of your painting needs.) If your cabinet has wood grain sides; remove old graphics and adhesive (adhesive may be removed with lacquer thinner. If you intend to use your original plexiglass, be sure it is in mint condition or it should be replaced. Thoroughly clean out your cabinet.
Time to Install Your New Goodies
Before You Start . . . Remember DO NOT Do this Work with the Power On!
Logic P.C.B. Cage Mount the logic cage securely (away from power supply). A Mark and drill pilot holes (3/32”). B_ Place the logic cage (bottom) over the holes and secure it with the supplied wood screws. C Install the PC.B. into the logic cage. Use feet and spacers supplied and adjust them so that the screws will go through the slots in the cage bottom.
Wire Harness
Attach the wire harness connector to the main logic board. CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Even if it is keyed, always triple check to be sure the wire inputs were connected correctly to the connector and the connector to the logic board.
Connecting the Wire Harness to the Existing Wires When you hook up the control panel, power supply, monitor or other subassemblies that remain in the game cabinet to your new wire harness, try and use their existing secondary connectors.
- Cut the original wire approximately three inches from the original connector. Strip off about one half inch of insulation.
- Solder the new wire designated for that position to the original wire you just stripped.
- Melt shrink tubing around all your in-line wire connections. Do not use electrical tape. Tape could unravel over a period of time due to the cabinet heat and cause you a great deal of trouble.
- Use wire tie wraps, and secure the cable to the cabinet whenever it seems necessary. Remember this is a new game, not a sloppy conversion.
Power Wires
- Connect the wires that are designated for your power supply. You will need a supply of +5V, +12V & ground. Your new game package may not require all of the voltages that were used in the original game. Tie off any unused wires.
- You will notice that you probably have more than one wire for each voltage. It is a good idea to use all wires supplied (double up if it is necessary). This will help to ensure that you don’t overload the edge connector pins and cause them to ‘‘burn’’.
Monitor Wires
You will be connecting the wires designated for the RED, GREEN & BLUE video guns along with the SYNC & GROUND wires.
Speaker Wires Find the two wires that are designated for the speaker and hook ’em on up.
Coin Door Wires
- Connect the designated wires to the coin switches and meter.
- You can connect your door lamps to the unused —5V power supply. Some games have separate power outputs for the coin door lamps.
- Be sure to clean and lubricate your old coin mechanisms. Keep the money coming in.
Guess What?
You are almost done with the electrical connections of your new game. All you have left is the control panel wiring. But we are going to hold off on that for right now. We have a few other things we need to do first. So why don’t you go ahead and get yourself a drink of water and stretch your legs. When you return, we can take a fresh look at your progress and then move forward.
Smoke Test
What Test?
Don’t worry. All this means is that you are ready to apply power to the system for the first time and you pray that there will be no smoke from a simple oversight. You are just about ready to power up the logic board. But first we need to recheck your work.
- Carefully inspect the game for loose power wires, exposed connections and extra fastening hardware.
- Make sure the logic board, board cage, monitor, and power supply are securely fastened in place.
- Double check the connectors to be sure they are wired and connected properly.
- Set the dip switches on the logic board to the factory recommendations.
Time to Apply Power: 1.
2. Look and smell for smoke. (TURN OFF IMMEDIATELY IF ANY IS NOTICED) Listen for game sounds. If after one minute you have not heard any sounds: A) Check for proper dip switch settings. B) Adjust volume control and check speaker connections. C) Check the +12V power supply to the logic board.
HORIZONTAL SYNC INPUT FROM PC.B. 5 Voc (OR COMPOSITE SYNC INPUT) HORIZONTAL SYNC OUTPUT TO MONITOR (OR COMPOSITE SYNC OUTPUT) VERTICAL SYNC OUTPUT FROM PC.B.
VERTICAL SYNC OUTPUT TO MONITOR
NOT USED
GROUND
G07 MONITOR SYNC MODE
- Replace R314 from 3900 to 1.8KQ resistor
- Replace C303 from .1yf 35V cap, locate ‘‘+’’ side of cap to emitter of X305
- Replace C501 with .1pf (old C303)
B) Now how’s your picture? ¢ Is it centered? ¢ Is it too bright or dim? ¢ Is it in focus? Check your monitor manual for these adjustments. If your screen looks ‘“‘off’’ then your new game transformation may have been in vain. So let’s take the time to make the monitor look great. Is the picture upside-down? Dip switch 5 on switch bank ‘“‘C” should solve your problems. Cc
Control Panel Assembly
- Remove the buttons, joysticks and wire harness and put them aside for now. Do not remove the original panel overlay until the new holes have been drilled.
- Mark positions on the panel for the new holes. CAPCOM supplies a clear 1/8” thick of plexiglass with every new game package to convert the control panel. We feel that your new game investment is well worth protecting. . .and the control panel is the first place to show wear and tear. ¢ You will need to cut this piece to size. Use the control panel as a template. ¢ Use a razor knife to score the plexiglass deeply. Then use a pair of pliers to break away the extra plexiglass.
- Now drill the holes in your panel that you have marked off for the buttons, joystick and bolts.
- Drill the same holes on your plexiglass panel protector. Once again use your panel as a template. Hint: To avoid chipping while you are drilling the holes, place the plexiglass securely on a soft wood surface and use a plexiglass drill bit and hole cutter.
- The holes are now all cut. Smooth them out on your panel and plexiglass with a fine toothed file.
- Remove the original graphics overlay from the panel. Clean up the panel and install your CAPCOM graphics. Make It Easier: Peel the top half of the protective backing off of your graphics. Start from the center and smooth out your overlay. Make sure you have about an inch extra coming off the top. No bubbles please. Now peel off the bottom half and do the same as you did for the top.
- Adhere the instruction and function labels.
- Install the Plex Control Cover over your completed new game panel.
- Mount the joystick and the buttons to the panel and wire them up. (Use the existing Panel wiring if possible)
Marquee Installation
Using the original marquee as a template, Center your new game marquee graphics and score the new marquee deeply to fit the cabinet. Break off the excess with pliers. Be sure the light behind the marquee works. Everything should always work on a new game. Take your time. . .Don’t forget this is going to be a new game.
Side Graphic Installation
Be sure sides of game are clean and free of old adhesive, dust, etc. Mark position of decal with eraseable pen or pencil (centered on upper half of cabinet). Peel off top 1/4” of decal backing and apply to cabinet with a smoothing motion (use a soft rag). Continue peeling off backing and smoothing. Remove any small bubbles with a pin or razor blade (pop them!)
Finishing Touches
Check the game inside and out for any imperfections. Secure any loose wiring or fastening hardware. Make sure the coin door is tight and the coin mechs are well adjusted. A game is no good to anybody if you can’t get a coin into it. Once again go over every step of this new game transformation in your mind. Be sure everything is correct and to your liking. Power up the game. A. Check all the coin switches. (Does the coin meter work?) B. Play your new game. ¢ Are all the player controls working? e Are the game sounds present? e Is the volume level proper? ¢ Are the dip switches set properly? Well, that’s about it. Good Luck.
At
Helpful Hints
Simple audio check for Board: TYPICAL AUDIO CIRCUIT FOR CAPCOM BOARD:
volume control +12VDC CONNECT EARPHONE BETWEEN POINT “‘A’” & GROUND. AUDIO = FROM CPU BOARD SHOULD BE HEARD. RGP102 Edge connector (see wiring list for correct pins)
speaker connections NEXT CHECK POINT “‘B” AND GROUND. ADJUST POT FOR LOUDNESS IN EARPHONE.
CHECK POINT “‘C’”” & GROUND FOR INPUT AUDIO TO PIN 3 OF HA13001 AUDIO CHIP. audio in
Also make sure Ground from +5VDC and Ground from +12VDC ARE TIED TOGETHER. IF GROUNDS ARE FLOATING, you could have audio problems.
NOTES:
8-WAY JOY STICK
BON BUTTON on BUTTON BUTTON
XN \/ 47 POSSIBLE 1 & 2 PLAYER LOCATIONS \
Control Panel Positions
CONTROL PANEL
8 WAY JOYSTICK SHOT JUMP
8 WAY JOYSTICK
CLIMB ON WALLS GO UPSTAIRS
CLIMB ON THE SLANT MOVE TO MOVE TO THE LEFT THE RIGHT
DESCEND ON THE SLANT
DESCEND ON WALLS CROUCH
CREDIT LIMITATION AT ONE TIME: 9 CREDITS
POSITION OF DIP SWITCH
A| 1-8 | «————— DIP SW (A)
B(_1-8 | ~———__ pPsw@e)
c([_1-8 | «———_ p Pswc)
VOLUME CONTROL | Lo JAMMA
MAIN HARNESS CONNECTIONS
| Wire Color | Solder Side | Parts Side | Wire Color | ||
| Black | Ground | A 1 | Ground | Black | |
| Black | Ground | B 2 | Ground | Black | |
| Red | +5VDC | Cc 3 | +5VDC | Red | |
| Red | +5VDC | D 4 | +5VDC | Red | |
| White | -5VDC | E 5 | -5VDC | White | |
| Yellow | +12VDC | F 6 | +12VDC | Yellow | |
| WA WA | Key | H 7 | Key | v, WA Ch, ] | |
| Brown | Counter 2 | J | 8 | Counter 1 | Brown |
| Red | Not Used | K 9 | Not Used | Red | |
| Black | Speaker (-) | L 10 | Speaker (+) | White | |
| Blue | Not Used | M 11 | Not Used | Blue | |
| Green | Video Green | N 12 | Video Red | Red | |
| Gray | Video Sync | P 13 | Video Blue | Blue | |
| Red | Service SW | R 14 | Video Gnd | Black | |
| Brown | Not Used | iS} 15 | Not Used | Brown | |
| White | Coin 2 | T 16 | Coin 1 | White | |
| Gray | 2P Select | U 17 | 1P Select | Gray | |
| Violet | 2P Up | Vv 18 | 1P Up | Violet | |
| Blue | 2P Down | WwW 19 | 1P Down | Blue | |
| Green | 2P Left | x 20 | 1P Left | Green | |
| Yellow | 2P Right | Y 21 | 1P Right | Yellow | |
| Orange | 2P Button A | Zz 22 | 1P Button A | Orange | |
| Red | 2P Button B | a 23 | 1P Button B | Red | |
| Brown | Not Used | b 24 | Not Used | Brown | |
| Blue | Not Used | c 25 | Not Used | Blue | |
| Blue | Not Used | d 26 | Not Used | Blue | |
| Black | Ground | e 27 | Ground | Black | |
| Black | Ground | f 28 |
S Ground Black
CAPCOM GAME OWNER:
Please fill out card and register for Free drawing at COIN-OP SHOWS. YOU NEED NOT BE PRESENT TO WIN.
Remember to fill in S/N of PCB (S/N IS REQUIRED FOR DRAWING).
REGISTER FOR FREE DRAWING
CAPCOM U.S.A., INC. COIN-OP DIVISION 3303 Scott Boulevard Santa Clara, CA 95054
CAPCOM’
3303 Scott Boulevard
Santa Clara, CA 95054. (408) 727-0400
COMPANY NAME.
LAST NAME FIRST NAME
ADDRESS.
cITY STATE ZIP CODE AREA CODE PHONE NO.
PRODUCT PURCHASED: DATE OF PURCHASE PURCHASED FROM:
HOW WOULD YOU RATE THIS GAME: EXCELLENT VERYGOOD( FAIRC] POOR HOW DID YOU HEAR ABOUT THIS GAME: MAGAZINE FRIEND OTHER
DO YOU OWN ANY OTHER CAPCOM ARCADE GAMES? YESO NOOO PLAN TO BUYIN NEAR FUTURE 0 WHAT TYPE OF ROUTE DO YOU OWN: ARCADE (]) SMALL ROUTE 1] LARGE ROUTE (1 HOW MANY GAMES DO YOU OWN
WHAT CAPCOM ARCADE GAMES ARE YOU FAMILIAR WITH: SPEED RUMBLER C1] SECTIONZ() LEGENDARYWINGS DD AVENGERS 19430 STREETFIGHTERO) OTHER
COMMENTS: i i mentinnaninsicteceistec tee iecenenmeen senses ncwedtenancesnenenscssescdl