CATHODE RAY TOMES

Domino Man Parts and Operating Manual (Nov 1982)

Domino Man (set 1) (Bally Midway, 1982) · Parts & Operating Manual · 88 pages · 43 sections · original scan

Page 1

November 1982 Game Nos. 316 & 317

NO. 317 COCKTAIL

NO. 316 UPRIGHT

MIDWAY MFG. CO.

10750 W. Grand Avenue Franklin Park, Ilinois 60131 U.S.A.

Phone: (312) 451-1360 Cable Address: MIDCO Telex No.: 72-1596

Form No. 0316-00300-0000

Page 2
WARNING THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
WARNING: This equipment generates. uses. and can radiate radio frequency energy and if not and used in accordance with the instructions manual. may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J of PART 15 of FCC RULES. which are designed to provide reasonable protection against such interference when operated in a commerical environment. Operation of this equipment ina residential area Is likely to cause interference in which case the user at his own expense will be required to take whatever ‘neasures may be required to correct the interference

ELECTRICAL BULLETIN: FOR ALL APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANOARD C22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

ExPSsuee. BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

CBallly|MIDWAY

Spwites You Ta Use

OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Continental U.S. 800-323-7182 Illinois Only 1-800-942-0497

® COPYRIGHT MCMLXXXIII BY BALLY/MIDWAY CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.

Page 3

DESCRIPTION TABLE OF CONTENTS

Introduction

Location and Setup INSPeECtiOn oie cece eee eee e teen e eee eens .2-1 installation 12-1 Self-Test ... 2-3 Game Volume Adjustment Control 2-3 Option Switch Settings 12-4

Game Operation Self-Test Mode .. Attract Mode.... Ready to Play Mode. Play Mode.......... Two Player Operation ...

Maintenance and Repair Cleaning 41 Fuse Replacement .. 4-1 Opening the Control Panel ... 4-2 Removai of the Main Display Glass & T.V. Bezel. 4-3 TV. Monitor Replacement......... 74-4 Printed Circuit Board Replacement 4-6 Opening the Attraction Panel 47

Illustrated Parts Breakdown No. 303 — Domino Man — Upright — Front 5-2 No. 303 — Domino Man —- Upright — Front 5-3 No. 303 — Domino Man — Upright — Rear 5-4 No. 303 — Domino Man — Upright — Rear — Parts List . 5-5 No. 303 — Domino Man — Upright — Header Fluorescent 5-7 No. 303 — Domino Man — Upright — Header Fluorescent Light Assy. — Parts List 5-7 No. 314 — Domino Man — Cocktail — Front .............. 5-8 No. 314 — Domino Man — Cocktail — Front — Parts List 5-9 No. 314 — Domino Man — Cocktail — Interior Access . 5-10 No. 314 — Domino Man — Cocktail — Interior Access — 5-11 Domino Man — Control Assy. — Parts List ... 5-12 Domino Man — Control Assy.... 5-13 Domino Man — Front Door Assy. 5-14 Domino Man — Front Door Assy. — Parts List . 5-15 Domino Man — Power Chassis Assy. — 125VA, o 5-16 Domino Man — Power Chassis Assy. — 125VA, 115V. All Versions — Parts List... . 5-17

Page 4

TABLE OF CONTENTS (cont'd)

DESCRIPTION PAGE

VI. Technical Troubleshooting .......... 6.00 e cece cece cee erence nee ee ene e nent eens 6-1 Introduction 2. 6-1 General Suggestions .. -6-1 Harness Component Troubleshooting .6-1 Transformer and Line Voltage Problems 6-2 A Glossary of Microprocessor Terms + 63 Introduction to the Z80 CPU...... -6-3 General Purpose Registers . 6-4 Arithmetic and Logic Unit (ALU)... 6-4 Instruction Register and CPU Control .. +. 6-4 Z80 CPU Pin Description +. 6-4 MCR Ii System P.C. Board Jumper Options... . 6-7

Vil.

Vil. Coin Door Maintenance ........... 6.06. c cece cece eee rete eet b nett n este tenn eees Metal Coin Acceptor Merchanisms . . Plastic Coin Acceptor Mechanisms. .

TV. Monitor Manual Introduction Symptom Diagnosis . Guide to Schematic Symbols . Troubleshooting. Theory of Operation. Differences Between Monitors Controls You May Not Touch . Parts Interchangeability ...... Wells Gardner Monitor Schematic — 19” ... Wells Gardner Monitor Replacement Parts List . Electrohome Monitor Schematic — 19”..... Electrohome Monitor Replacement Parts List . Electrohome Monitor Schematic — 13” . Electrohome Monitor Replacement Parts List .......... 0... c eee c eee e ene ee eee teens

Schematics & Wiring Diagrams Wiring Diagram (All Versions) Dual Power Amp P.C. Assy.—Component Layout Dual Power Amp P.C.—Schematic Super Sound I/O P.C. Assy.—Component Layout Super Sound I/O P.C.—Schematic cee Super C.P.U. P.C. Assy.—Component Layout Super C.P.U. P.C.—Schematic Video Generator P.C. Assy.—Component Layout. . Video Generator P.C.—Schematic 125 VA Power Supply P.C. Assy.—Component Layout . 125 VA Power Supply P.C.—Schematic . 125 VA Power Chassis--Schematic COCOOOCOOOOS ai omNonakon4 iLerasy

Page 5

TABLE OF FIGURES

FIGURE

Assigned Point Values Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assemblies Interlock Switch Operation ........ 3 Game Volume Adjustment Controi . Option Switch Locations Option Switch Settings .. identification of “On Screen” Graphics Self Test Mode............ Self Test Mode — Sounds . Self Test Mode — Player Input . Self Test Mode — Bookkeeping Self Test Mode — Time Report. Self Test Mode — Score Report Self Test Mode — Setup Options. Self Test Mode — Channel Test .. Location of Hardware Master Reset Switch : Location of Fuses .....--- 0.0.00. e eee 4 Opening the Control Panel — Upright. Opening the Cocktail Game . Removing the Control Panel OC! Removal of Main Display Glass & T.V. Bezel — Upright Removing Top Glass — Cocktail . Removing Monitor — Upright... Opening the Cocktail Game . Removing Monitor — Cocktail . Replacing P.C.B.s — Upright. Replacing P.C.B.s — Cocktail Opening the Attraction Panel — Upright .. Replacing Fluorescent Tube Starter — Upright. Removing and Replacing the Coin Acceptor . Cieaning the Metal Coin Acceptor .... Lubricating the Metal Coin Acceptor Opening the Plastic Coin Acceptor.... Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters i PPEPEPEEEESERRM | artoasccs

ma]

ap BAAKRKROONNIKO oasis Rowman NUNNNEREEREER EER EEREREOO OOH EKOOHONYYNNS TDERWONjAHRA4ABODNDHAHRWONAWHNNNNNNYN]ATHAWNMA= ee ee ieee Fe

iii

Page 6

Domino Man

IMPORTANT NOTE

DO NOT plug in your new game yet. Before you do anything to your game, we recommend that you read SECTIONS | and {| of this manual completely. It will not take more than a few minutes and it may be very helpful.

I. Introduction

DOMINO MAN is a one or a two player game. There are two models: the “UPRIGHT” and “COCKTAIL TABLE”. The Upright model has been designed for either RIGHT or LEFT hand use. When the two player mode is selected on the Upright model, the players take turns at the controls to take their Domino Man through the garne course. If you have purchased the Cocktail Table model of this game, the rules of play are the same. The only difference is that in the two player mode of the Cocktail Table game, the picture flips to face you when it’s your turn. When playing this game, the Domino Man is under YOUR control. YOU make him move back and forth or up and down on the screen to place his Dominos, take them out of the Bully’s way, and to move the other various people on the screen around to keep them from knocking down his row of Dominos. The game is presented in phases, and there are 3 racks to a phase. The 3 racks which compose a phase are arranged as follows: the FIRST RACK is a street scene, the SECOND RACK takes place on the golf course, and the THIRD RACK is in a construction site. All your Domino Man wants to do is set up his Dominos. (This is accomplished by having him step on the WHITE dot.) However, ali the other people in each of the above three scenes are not very careful

1-1 and will wander into his Dominos knocking them over if he does not keep changing their paths of travel for them. This makes his life rather hectic to say the least. The ONLY person on the screen that CANNOT be turned aside is the Bully. The only thing youcan doto him is have Domino Man jump up and down on his head to speed up his passage. BE SURE you have removed any Dominos that were in front of him FIRST or he will knock them ALL over. In order to have your Domino Man do anything other than just place Dominos, you must push the “SAVE” button when you want him to do it. For example: he cannot move or change the direction of travel of any of the other people on the screen in any way whatsoever UNLESS the SAVE button is depressed when he is trying to do this. As your skill level increases and you work your way into the higher and higher racks, the patterns in which the Dominos must be placed become more complicated, the other people on the screen appear more often, and they move faster. Bonus Domino Men are awarded to you periodically throughout the game as you reach or pass certain preselected point values. Each item in the game that can contribute to your score is assigned a point value as shown in Figure 1-1.

Page 7

Major Features

There are several major features in your DOMINO MAN game: 1) The UPRIGHT model has been designed for ease of play by EITHER RIGHT- HANDED or LEFT-HANDED players; 2) You can select the level of difficulty at which you want to play (NOVICE or EXPERT); 3) You can vary the speed at which your Domino Man travels through the game course by pressing AND HOLDING DOWN the SAVE Button; 4) The game has OWNER/OPERATOR selected variable levels of difficulty so game play can be tailored to player skill level in his area; 5) There is a new and easy to use diagnostic package featuring: a complete ROM/RAM check with bad chip location information readout on the monitor screen; the capability to check each of the game's 15 different sounds INDIVIDUALLY; provision for checking each control and switch SEPARATELY; a full function Bookkeeping mode; an entire options list that can be

DESCRIPTION PLACING DOMINO TURNING AN INTRUDER AROUND PER SECOND OF PUSHING AN INTRUDER PUSHING INTRUDER OFF-SCREEN SWATTING A BEE MONEY BAG (RANDOM) NOT LOSING MAN DURING RACK NOT ALLOWING A DOMINO TO FALL DURING RACK IF BOTH OF ABOVE (Maximum 15,000) set from the front console with NO NEED to crawl inside the back of the cabinet and look for tiny switches located on P.C. boards; a sound system test; and a “PRE-SET” category that can return ALL information in the Bookkeeping mode to zero and/or all operator selected options back to factory recommended settings; and 6) The game is equipped with a rechargeable battery so that it won't forget where it was the night before at closing — even if you turn it off. It will “remember” this information for up to two weeks.

Game Objective

The object of the game is to HAVE FUN while constantly increasing your skill as you play, running up the highest score possible each time.

POINTS AWARDED

100, 200, 250, 500 250 x RACK # 250 x RACK # 1000 x RACK #

BONUS TIMER ADDED TO SCORE AT RACK END

Figure 1-1 Assigned Point Values

1-2

Page 8

Il. Location and Setup

INSPECTION:

1.

2. Remove the game from its shipping crate. Inspect the entire outside of it for any signs of damage. O Any scratches?, dents?, cracks? O Any broken controls? OC Any broken glass or plastic? O Just look it over closely and make a note of any signs of damage. . Remove the shipping cleats from the bottom of the cabinet. © UPRIGHT MODELS ONLY: In order to help prevent easy theft of your game, you may wish to remove the Caster Wheel Assemblies from the bottom of your cabinet at this time.

. install the four levelers, one at each corner of the cabinet. O Level the cabinet. . Open the cabinet and inspect the inside of the game for any signs of damage. See Figure 2-1. OD Also check to make sure all plug-in connectors on the wire harness are firmly seated.

NOTE: ALL connectors or plugs are keyed so they will only go together when all pins are properly lined up. © Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. O Make sure all printed circuit boards (P.C.B.'s) are firmly seated in their connectors. See Figure 2-1. These connectors are also keyed. The P.C.B.’s will only go into them one way without being damaged. 1 Note the location of the game's serial number. See Figure 2-1. O Check all major subassemblies to be sure they are mounted securely. These are called out in Figure 2-1. Power supply. Control panel(s). T.V. monitor. Other P.C.B.’s and/or P.C.B. rack, etc. Power supply filter assembly. Transformer board assembly.
  • Make a note of any problems that can’t be easily corrected.
  • Call your distributor and/or service man about your problem list.

INSTALLATION

  • Location requirements: O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz O Temperature: 32° to 100°F (0° to 38°C) O Humidity: Not over 95% relative O Space required: Upright 29" x 25" (73cm x 63cm) Cocktail 32” x 22” (81cm x 55cm) O Game height: Upright 68" (170cm) Cocktail 29” (73cm)
Page 9

SERIAL

POWER SUPPLY P.C.B.

UPRIGHT REAR

SERIAL NUMBER (MAY BE LOCATED ON ANY CORNER)

CONTROL PANEL (PLAYER 1)

POWER SUPPLY P.C.B.

INTERLOCK SWITCH (INSIDE DOOR) ——— —— ON/OFF SWITCH

TV. MONITOR

INTERLOCK : : SWITCH “ CONTROL PANEL

POWER SUPPLY CHASSIS

UPRIGHT FRONT

TV. MONITOR

CONTROL PANEL (PLAYER 2)

POWER SUPPLY CHASSIS nomenmaiiiiminse | -

ON/OFF SWITCH UNDER TABLE ON PLAYER 2 COCKTAIL INTERIOR SIDE

Figure 2-1 Location of Serial No., Interlock Switch, On/Off Switch, & Major Sub-Assemblies

2-2

Page 10
  • Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to be sure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. \f the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN unti! you have talked with your distributor and/or service man and obtained a solution to this problem. Otherwise you could damage your game. . Interlock and power ON/OFF switches: See Figure 2-1. O To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright model). O When any access door is opened, the interlock switch installed there turns off all power to the game. DO Check each Operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outiet. The game ON/OFF switches for both models are located as shown in Figure 2-1. Turn the game on and allow it to warm up a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright model). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). lf this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. interlock switch for proper After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s} open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 2-2.

Figure 2-2 Interlock Switch Operation

SELF-TEST Your new game will Self-Test itself to see if it has any bad parts. The information it receives while testing itself will be shown on the T.V. monitor. Some information can also be heard through the game's speaker system. See the GAME OPERATION section for a more detailed description of this function. When there is a bad result according to the Self-Test, call your distributor and/or service man to have the trouble fixed unless it is something you can do yourself (such as replace a bad RAM or ROM chip).

GAME VOLUME ADJUSTMENT CONTROL See Figure 2-3. The game volume controi pot is located just inside the cabinet on the right side of the coin door frame. There is only one pot. For adjustment, it may be reached through the coin door on both models. To make the sounds louder, turn the pot ciockwise as you face it ( 77 ). To make the sounds less loud, turn the pot counterclockwise as you face it ( ¢~\ ).

Page 11

OPTION SETTINGS To change the most common option settings, youDO NOT have to take the game apart or go into the cabinet and hunt for tiny switches on P.C. boards. These most common options can be changed from the main console of the game while it is in the Self- SERVICE Test mode. The Self-Test switch is located just inside CREDIT the cabinet on the right side of the coin door frameas SWITCH you face it.

When changing any options, ALWAYS perform the Self-Test and play the game to be sure the ones selected are working properly. Of course, when you SELF-TEST must change one of the switches that is located on SWITCH one of the game’s P.C. boards, it is also recommended that you perform the Self-Test and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and VOLUME this can happen.) AD STMENT The P.C. Board option switch settings, and what they will make the game do are shown in Figure 2-5. These switches are MAINLY INTENDED for use by a technician who is checking and/or performing tests on the game. See Figure 2-4 for option switch locations.

NOTE: In order to set the option switches located on the game’s P.C. Boards, these Boards need not be Figure 2-3 Game Volume Adjustment Control removed from their card rack.

OPTION SWITCH 1

Figure 2-4 Option Switch Locations

2-4

Page 12

DOMINO MAN

OPTION SWITCH SETTINGS

SWITCH NO. 1— AT B 3 — LOCATED ON SOUND 1/0 P.C. BOARD

DURING GAME PLAY: SW#1 SW#2 SW#3 SWH#4 SW#HS SWHE SWH7 SW#8 SWHS SWH10

**PLAY MUSIC ON NOT NOT NOT NOT NOT NOT DO NOT PLAY MUSIC OFF USED USED USED USED USED USED

BLACK SCREEN CHARACTERS ON *“*CAUCASIAN SCREEN OFF

UPRIGHT COCKTAIL TABLE

FREEZE VIDEO **NORMAL OPERATION

**NORMAL OPERATION RAM/ROM TEST INDICATES TEST RESULTS VIA _ YELLOW LED ON SOUND 1/0 BOARD: FAST FLASH = BAD ROM SLOW FLASH = BAD RAM

**NORMAL OPERATION OSCILLATOR TEST

**NORMAL OPERATION FILTER TEST

*NO EFFECT IF SW#1 OF SWITCH NO. 3 IS IN THE “OFF” POSITION. **FACTORY RECOMMENDED SETTINGS. PART NO. M051-00303-A011

The remainder of Domino Man's most common option settings are conducted during the machine setup portion of the Self-Test mode and will be covered in detail in that section of this manual.

Figure 2-5 Option Switch Settings

2-5

Page 13

Ill. Game Operation

DOMINO MAN is a one or a two player game with a The game has five possible modes of operation: ATTRACT, READY-TO-PLAY, PLAY, HIGH SCORE color T.V. monitor. The game gives a display which has all the parts shown in Figure 3-1. INITIAL, and SELF-TEST.

DOMINO MAN

TIMER

RACK IDENTIFIER

Figure 3-1 Identification of “On Screen” Graphics

SELF-TEST MODE

The Self-Test mode is a special mode for checking game play statistics as well as game switches and computer functions. It is the easiest and best way to check for proper operation of the entire game.

NOTE: Putting the game into Self-Test WILL NOT cause the game to erase any CREDITS it has in its memory when the Self-Test mode is entered.

After the power to the game is on, you may begin a Self-Test at ANY TIME by sliding the Self-Test switch (switch is located just inside the cabinet on the right side of the coin door frame as you face it) to the “ON” position and then activating the “TILT” switch (located on the back side of the coin door just below the lock mechanism). The game will then IMMEDIATELY go into the Self-Test mode. The Self-Test mode has eight (8) major categories as illustrated by Figure 3-2.

  • It is easy to select what category you want to enter. By pushing the control stick forward or pulling it back, the Cursor at the left of the screen can be moved UP and DOWN, (forward = UP) and (backward = DOWN), until it is in front of the category you want to test. Release the conirol stick at this time.
  • After the Cursor has been positioned, depress either “RUN/SWAT” Button on the console and the monitor screen will display the test category you have selected, O Once you are IN one of the Self-Test mode categories, FOLLOW THE ON-SCREEN IN- STRUCTIONS TO COMPLETE THE TEST.

Figure 3-2 Self Test Mode

Page 14
  • The next group of Figures (3-2a through 3-2g) show the CORRECT screen presentation for EACH category of the Self-Test mode. During the SELF DIAGNOSTICS section of the Seif- Test mode, you will first see a cross hatch pattern on the screen for about 1/2 second. Second, you willsee a lot of different colored bars shown on the monitor screen. These bars will be UNpainted one at a time from left to right. Third, you will see the screen painted Red, Blue, and Green in bars from left to right. Fourth, all the different colored bars you saw “Second” are displayed again. And fifth, the different colored bars are replaced by this message: “PRESS RUN BUTTON TO EXIT”. If the RUN Button is nothit, the test will repeat itself. This feature was designed into the game to enable overnight testing for an intermittent hardware problem. \f the SELF DIAGNOSTICS find one or more bad ROM or RAM chips: instead of going through what is described above, the game will give you a written message as to which parts are bad. This message includes their |.D.’s and their P.C. Board locations. During the SOUNDS section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-2a. D In this category, each of the game’s sounds can be checked individually in any order — or — you can tell the game to check them all in order.

Figure 3-2a Self Test Mode — Sounds

During the PLAYER INPUT section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-2b. You MUST hit the TILT SWITCH to EXIT this test.

D In this category, each of the game's player operated controls — including the coin switches on the back side of the coin door — may be checked individually. A game sound will be heard as each switch/control is actuated. If no game sound is heard, that switch/control is either not working, miswired, or disconnected. Check it out thoroughly.

hes and Devices are activated, the Switch ‘spelled out in the blank space at center As the Player Input S or Device activated of screen.

Figure 3-2b Self Test Mode — Player Input

During the BOOKKEEPING section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-2c. C1 In this category a basic bookkeeping function is performed. And with the selection of the “TIME REPORT” and the “SCORE REPORT", detailed breakdowns of the game times and scores may be obtained.

Figure 3-2c Self Test Mode — Bookkeeping

\n the TIME REPORT and SCORE REPORT sections of the BOOKKEEPING mode, the game will give displays which look like those shown in Figure 3-2d and 3-2e respectively.

Page 15

D In this category, all common game options may be changed from the control console: coins per credit, credits per base, extra base(s) awarded at, difficulty level - -, and so on.

DIFFICULTY LEVEL EXPLANATION: The Difficulty Level setting has a rangeof 1 to9 with 1 representing the easiest level of play and 9 representing the most difficult level of play. Three is the factory recommended setting. AWARD OF BONUS BASES EXPLANATION: Bonus Bases are awarded to the player when he reaches or passes certain pre-selected point values. These are Owner/Operator selectable. As a starting point, the factory recommendation is 20,000 (first Man) and EVERY ADDITIONAL 20,000 (another additional Man).

During the CHANNEL TEST section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-2g. O In this category, the game conducts a test of its SOUND SYSTEM.

Figure 3-2e Self Test Made — Score Report

During the SETUP OPTIONS section of the Self-Test mode, the game will give a display which looks like that shown in Figure 3-2f. Figure 3-2g Self Test Mode — Channel Test

Once you enter the CHANNEL TEST section of the Self-Test mode, the game automatically tests Channels 1 through 6 giving a tone for each one as it checks it. After the 6th Channel is tested, the game automatically repeats the test until the RUN Button is hit. It then goes back to the Self-Test Mode Menue. The “PRE-SET” category returns ALL information in the Bookkeeping mode to zero and sets all operator selected options back to factory recommended settings. This is accomplished by positioning the cursor in front of the “PRE-SET” category in the Self-Test Mode Menue and pressing the RUN Button. During the GRID DISPLAY section of the Self-Test . mode, the game shows a white cross hatch pattern on

  • = Factory recommended settings. the monitor screen. This is for alignment and/or test
NOTE: You MUST hit the RUN BUTTON to EXIT this test. purposes. This pattern will remain on the monitor screen until the RUN Button is hit. The game will then Figure 3-2f Self Test Mode — Setup Options go back to the Self-Test Mode Menue.
Page 16

To leave the Self-Test mode, simply slide the Self-Test switch to the “OFF” position at ANY time. The game will then run through the ROM/RAM test display after which normal game functions will return to the monitor screen. CROSS HATCH PATTERN: A cross hatch pattern is shown on the screen when power is first turned on to the game, when the TILT Switch is actuated, during the “SELF DIAGNOSTIC” portion of the Self-Test mode, and during the “GRID DISPLAY” portion of the Self-Test mode. This pattern may be kept on the screen for adjustment purposes as described earlier. When you are finished using the cross hatch pattern, simply hit the RUN Button to return to the Self-Test Mode Menu.

HARDWARE MASTER RESET SWITCH: There are two of these little red switches, one on the Sound I/O Board and one on the CPU Board, located as shown in Figure 3-3. The function of each of these switches — when pressed — is to make the game THINK it has JUST been turned on. They set up an “initial power-up” condition. We DO NOT recommend that you indiscriminately press EITHER of these switches. They should ONLY be used if there is a major problem encountered while testing the P.C. Boards.

ATTRACT MODE

  • The Attract mode starts: O Just after power has been turned on to the game. (Self-Test switch is in the “OFF” position.) C After a Self-Test has been completed and there are no more credits left in the game's memory. Q After a play has been finished, the score was not high enough to put the game into the High Score/Initial mode, and there are no more credits left in the game’s memory. O After the High Score/Initial mode when there are no more credits left in its memory.

O In the Attract mode, the game will give the following displays centered on the monitor screen: No matter where the game is in the Attract mode sequence, it will immediately add the words “CREDIT 1 PRESS 1 PLAYER” or “CREDIT 2 PRESS 1 OR 2 PLAYER” (depending on how many coifis have been inserted) to the bottom of each display of the Attract mode sequence.

HARDWARE MASTER RESET SWITCHES

Figure 3-3 Location of Hardware Master Reset Switch

Page 17

Attract Mode Display 2

READY-TO-PLAY MODE

  • The Ready-To-Play mode starts when enough coins have been accepted for a 1 or a 2 player game. This display (“CREDIT 1 PRESS 1 PLAYER” or “CREDIT 2 PRESS 1 OR 2

GREBIY £ PRERSE <& PLAYER Attract Mode Display 4

PLAYER”) will continue to be a part of each Attract mode display sequence until the “1 PLAYER” or “2 PLAYER” Button has been pressed.

  • In the Ready-To-Play mode, the game will give the following displays centered on the monitor screen.

CHERET & PRES 1 FLEE

Ready-To-Play Mode Display 1

3-5 Ready-To-Play Mode Display 2

Page 18

f GRERET £ PEESR i PLATER a” 2g eee

-Play Mode Display 6 Ready-To. Play Mode Display 3 Ready-To-

Play Mode Display 7 Ready-To-| Ready-To-Play Mode Display 4

eo a PLeve eT o

Ready-To-Play Mode Display 8 Ready-To-Play Mode Display 5

3-6

Page 19

PLAY MODE

1.

Fad The Play mode begins when the 1 or the 2 PLAYER Button is pressed. When this happens, the first game scene is displayed on the monitor screen. The Play mode ends when all the Dominos have been knocked over, the Clock knocks over the first Domino in the line that your DOMINO MAN has been placing, or when your last DOMINO MAN has been stung by the Bee. ON THE SCREEN: The game is presented in phases. There are 3 racks to a phase. The 3 racks which compose a phase are arranged as follows: the FIRST RACK is a street scene, the SECOND RACK takes place on the golf course, and the THIRD RACK is in a construction site. When playing this game, the Domino Man is under YOUR control. YOU make him move back and forth or up and down on the screen to place his Dominos, take them out of the Bully's way, and to move the other various people on the screen around to keep them from knocking down his row of Dominos. At the beginning of each rack (in the TWO PLAYER games ONLY), the game tells which player is up BEFORE play begins. The Rack Timer (the Alarm Clock) is also set atthe beginning of each rack and after the loss of each DOMINO MAN.

Also indicated in each rack is the rack number you're playing, the number of players (1 or 2), and a running total of the players’ score(s). PLAY BEGINS: Your DOMINO MAN appearsat the top center of the monitor screen. . ALARM CLOCK: The Alarm Clock (rack timer) appears at the upper right side of the monitor screen and starts its movement down the right side of the screen, across the bottom (to the left), and up the left side of the screen where it will knock over the first Domino in the line if you have not finished setting the last Domino in this rack by the time it gets there. NOTHING can affect it in ANY way. RACK BONUS: This Bonus is linked with the Rack Timer. As the rack begins it is set at some value and counts BACKWARD as rack play continues. So, the faster your DOMINO MAN can get all his Dominos set in each rack, the higher will be his RACK BONUS. . DOMINO DOT: A black dot appears that you have to make DOMINO MAN get close to with his foot in order to place his Dominos. A message telling you to do this in order to piace the Dominos also appears briefly on the screen about this time. . MONEY BAG: Several times during each rack, a Money Bag will appear at a random location on the

3-7 screen for a short period of time. If you run it over with your DOMINO MAN, you will be awarded the bonus points for this Money Bag. If it should disappear BEFORE you have the opportunity to run it over, it WILL reappear again DURING this particular rack. The Money Bag bonus point values are displayed on the screen at the time they are run over.

  • BEE: The Bee in each rack will try to sting your DOMINO MAN. If it does, you will lose one DOMINO MAN. Whenever you are close to the Bee, DOMINO MAN can make it go away for a short time by pushing the SWAT Button and centering (or letting go of) the joy stick momentarily — which will cause him to swat the Bee witha Domino. The Bee will then go away for a few seconds and reappear again to chase your DOMI- NO MAN until he swats him again.
  • BULLY: He appears at random times and at random places along the top of the screen and walks toward the bottom of the screen. He is the ONLY on-screen participant that CANNOT be moved to the side. He just walks straight down toward the bottom of the screen. DOMINO MAN must remove any Dominos that are in his way. If he should touch them, he will cause the whole line to start falling. If DOMINO MAN can get ahead of the falling Dominos, he can remove one and thus SAVE the remainder from being knocked over. Once any Dominos have been removed from the BULLY'S path, DOMINO MAN can jump up and down on his head to help him across the area where he would like to place his Dominos. OTHER ON-SCREEN PARTICIPANTS: All your Domino Man wants to do is set up his Dominos. (This is accomplished by having him get his feet close to the BLACK dat.) However, al! the other ONSCREEN PARTICIPANTS in each of the above three scenes are not very careful and will wander into his Dominos knocking them over if he does not keep changing their paths of travel for them. This makes his life rather hectic to say the least.
  • (SAVE) RUN/SWAT BUTTON: In order to have your Domino Man do anything other than just place Dominos, you must push the (SAVE) “RUN/SWAT BUTTON” when you want him todo it. For example: he cannot move or change the direction of travel of any of the other ON- SCREEN PARTICIPANTS in any way whatsoever UNLESS the (SAVE) RUN/SWAT BUTTON is depressed when he is trying to do this. He must have the (SAVE) RUN/SWAT BUTTON pressed in order to: 1) run, 2) swat the Bee,
  • remove Dominos, and 4) move other On- Screen Participants. 1.
Page 20

13.

15. BONUS DOMINO MEN: These are awarded when the player reaches or passes certain operator selected point values (see the “MACHINE SETUP” section of this manual for the individual point values at which each bonus DOMINO MAN can be awarded). . PLAY ENDS: The Play mode ends when all the Dominos have been knocked over, the Clock knocks over the first Domino in the line that your DOMINO MAN has been placing, or when your last DOMINO MAN is stung by the Bee. HIGH SCORE/INITIAL MODE: If your score was high enough to become one of the ten best scores, the game will go into the High Score/ Initial mode immediately aftr the above display. If your score is not high enough to cause the game to go into the High Score/Initial mode, it will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready- To-Play mode (if there are still credits ieft in its memory). In the High Score/Initiai mode the game gives a display which looks like the following. : By pulling the control stick toward you, you can make the displayed letter cycle through the alphabet: “A”, “B”, “C”, “D”, etc. By pushing the contro! stick away from you, you can make the displayed letter cycle through the alphabet in the other direction: “2”, “Y", “X”, “W”", etc. When you reach your initial, release the control stick and push the RUN/SWAT Button. Your intial is frozen in place. If you do not wish to put your initials opposite your score, just press the RUN/ SWAT Button three times. Three “A”’s will appear on-screen where your initials would have been entered. After the High Score/Initial mode, the game will either go to the Attract mode (if there are no more

High Score Initial Mode Display

3-8 credits left in its memory) or into the Ready-To Play mode (if there are still credits left in its memory).

  • Most of the above holds true in the “2 PLAYER” mode also. But there are a few minor differences.

TWO PLAYER OPERATION The Upright, and Cocktail Table models both have two player operation. In the two player mode, the rules of play are the same as in the single player mode. There are some additional rules, however. 1. In the Upright model, the players must take turns at the controls. . In the Cocktail Table model, each player has his own set of individual controls. The picture will flip to face you when itis your turn. (When itis not your turn, your set of controls will have NO effect on the game.) . Your turn lasts until your DOMINO MAN is stung by the Bee or until the first Domino in the row heis placing is knocked over. At this point, the game will do one of several things depending on whether or not the lost DOMINO MAN was your last or if you still have others remaining in reserve. LOST DOMINO MAN — OTHERS REMAINING IN RESERVE The game stops and “PLAYER__.” is displayedon the Screen. C Next, the other player's Scene and Domino pattern appear on the monitor screen and game play begins for the other player. LOST DOMINO MAN — NO OTHERS REMININGIN RESERVE G Game displays: “GAME OVER” “PLAYER __” on the monitor screen. After this, “PLAYER __” is displayed, the other player’s Scene and Domino pattern appear on the monitor screen and game play begins for the other player. O After the last player has finished his game, if either or both of the scores were high enough, it goes to the “HIGH SCORE/INITIAL” mode. The player(s) that attained the high score(s) is indicated by display if “1” (for PLAYER NUMBER ONE) or a “2” (for PLAYER NUMBER TWO) out to the left side of the high score(s) indicated on the screen in this mode. If your score(s) were NOT high enough to cause the game to go into the “HIGH SCORE/!INITIAL” mode, the game will either go to the Attract mode (if there are no more credits left in its memory) or into the Ready-To-Play mode (if there are still credits left in its memory).

Page 21

IV. Maintenance and Repair

Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS. The most important thing for you to remember is to run the Self-Test EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if all its controls and inside parts are working correctly. The Self-Test will inform you whether or not your game is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis. CLEANING

The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels. This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of plastic.

FUSE REPLACEMENT This game contains several fuses located as shown in Figure 4-1

  • UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Chassis and the Power Supply Board. . COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Power Chassis and the Power Supply Board. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of this manual. See the T.V. Monitor Manual (available on request from your distributor or the monitor manufacturer) © and/or the T.V. Troubleshooting Section of this manual for information on these fuses.

FUSES LOCATED ON POWER SUPPLY BOARD AND POWER CHASSIS

Figure 4-1 Location of Fuses

Page 22

OPENING THE CONTROL PANEL See Figure 4-2.

  • UPRIGHT MODEL: See Figure 4-2. O The control panel is held in place by two latches, one on the left side and one on the right side of the cabinet. They are spring loaded to provide constant positive pressure on their latch plates. LATCHES They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the front center of the control panel. Once they are released, unhook them from their latch plates. 0 To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling. The control panel is now free and can be removed. O To reinstall the control panel, reverse this procedure.

Figure 4-2 Opening the Control Panel — Upright

CLAMPS

Figure 4-3 Opening the Cocktail Game

4-2

Page 23

REMOVAL OF THE uFT . CONTROL UP MAIN-DISPLAY-GLASS AND/OR THE T.V. BEZEL ASSEMBLY

  • UPRIGHT MODEL: See Figure 4-5. REMOVE A
  • SCREWS NOTE: In order to do this, the control panel MUST be _EAGH SIDE removed first. See the “UPRIGHT MODEL” procedure. O Turn the power to the game off and remove the control panel. O This frees the main-display-glass so it can be ep lifted up.

m= O By putting your finger in the hole in the middle

of the main-display-glass support, you can lift it REMOVE) | up and out. See Figure 4-5. SCREWS CO Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the above mentioned screws and the bezel with four bezel-glass-clamps may be removed. O To reinstall the T.V. bezel assembly and the main-display-glass, reverse this procedure. Figure 4-4 Removing the Control Panel — Cocktail

  • COCKTAIL TABLE MODEL: See Figure 4-4. O Each control panel! is held in place by several screws, two on the inside of the cabinet and three along the outside bottom edge of the control panel. Turn power to the game off. Open the coin box door and release the two latches indicated in Figure 4-3.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL! DISPLAY GLASS

Once they're released, unhook them from their latch plates. Grasp the table top at “A” and open it as indicated in Figure 4-3.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

Remove the screws which secure the control panel in place. See Figure 4-4. GLASS O To remove the control panel(s): CLAMPING Disconnect it from its cabling. PLATE The control panel is now free and can be removed. O To reinstall the control panel, reverse this Figure 4-5 Removal of Main Display Glass & T.V. Bezel procedure. — Upright

4-3

Page 24
  • COCKTAIL TABLE MODEL: See Figure 4-6.
NOTE: This may be done with the table top in the closed or the open position. If you decide to open the table top, TURN THE POWER TO THE GAME OFF FIRST. O Remove the screws which secure the table top glass clamps in place. O Remove the table top glass. CO The bezel may now be removed. C To reinstall the T.V. bezel and the table top glass, simply reverse this procedure.

Figure 4-6 Removing Top Glass — Cocktail

T.V. MONITOR REPLACEMENT

CAUTION: High voltages may exist in any television unit, even with the power disconnected. Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held in your hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The TV. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANSFORMER.

4-4

  • UPRIGHT MODEL: See Figure 4-7. O Turn power off to the game. O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass MUST be removed. See above “Upright Model” procedure. O With the removal of only four bolts, the T.V. monitor will be loose.
CAUTION: BE SURE to support the T.V. monitor from the rear while removing the four bolts so it will not fall out of the cabinet.

O The monitor mounting channels slide on top of and against two metal guides mounted to the cabinet’s right and left sides. The monitor is removed by sliding it out the back of the cabinet. O To reinstall the T.V. monitor, reverse this procedure. O After replacing the T.V. monitor, be sure to run the game Self-Test.

REMOVE

  • BOLTS

Figure 4-7 Removing Monitor — Upright

Page 25

Figure 4-8 Opening the Cocktail Game

  • COCKTAIL TABLE MODEL: See Figure 4-9. O Turn the power off to the game. O Open the coin box door and release the two latches indicated in Figure 4-8.
CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!!

Once the latches are released, unhook them from their latch plates. O Grasp the table top at “A” and open it as indicated in Figure 4-8.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

O Remove the screws which hold the table top glass clamps in place. O Remove the table top glass. C Lift out the T.V. bezel assembly. O Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. O Remove the screws holding the T.V. monitor chassis to the “L” brackets by the door hinge(s). See Figure 4-9. O Close the Cocktail Table and re-latch it.

O Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. See Figure 4-9. QO Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both. O Lift the T.V. monitor straight up and out of the table top being very careful not to bump the neck of the picture tube. O To reinstall the T.V. monitor assembly, reverse this procedure. Be sure to check the clearance of the “L” brackets BEFORE setting the monitor into the table top. 0 After replacing the T.V. monitor, be sure to run the game Self-Test.

REMOVE 6 SCREWS (3 EACH SIDE) LIFT MONITOR STRAIGHT UP

a “REMOVE 4 SCREWS (2 EACH SIDE)

Figure 4-9 Removing Monitor — Cocktail

Page 26

PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT

  • UPRIGHT MODEL: See Figure 4-10. O Turn the power to the game off.

D Unlock and open the rear access door.

D Disconnect all cabling from the P.C. boards and lift them out of their card rack.

D Disconnect the linear power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 4-10 and slide the linear power supply board out the back of the cabinet. O To reinstall the above P.C.B.’s, reverse this procedure.

NOTE: P.C.B.’s are all keyed and will ONLY fit into their connectors one way without forcing them. The plugs on the cable harness which connect it to the P.C.B.’s are also keyed and will ONLY go onto their connectors one way without forcing them.
  • COCKTAIL TABLE MODEL: See Figure 4-11. O Turn the power off to the game.

O Open the cabinet: Open the coin box door and release the two latches indicated in Figure 4-8.

Sy REMOVE SUPPORT FROM SIDE OF CABINET AND LIFT P.C.B.S UP TO REMOVE REMOVE SUPPORT AND LIFT POWER SUPPLY BOARD UP TO REMOVE

Figure 4-10 Replacing P.C.B.s — Upright

4-6

CAUTION: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!

Once they’re released, unhook them from their latch plates. O Grasp the table top at “A” and open it as indicated in Figure 4-8.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

O Remove the linear power supply board. See Figure 4-11. : Disconnect it from all its cabling. Remove the two smallest P.C.B. supports. Once these are removed, the linear power supply can be lifted out the top of the cabinet. To reinstall the linear power supply board, reverse this procedure. D To remove the P.C. boards from the card rack. See Figure 4-11. Disconnect them from ALL their cabling. The P.C. boards are now free and can be slid from their rack. To reinstall the P.C. boards, procedure. reverse this

REMOVE (2) SUPPORTS TO REMOVE POWER SUPPLY BOARD FROM CABINET REMOVE BRKT. FROM SIDE OF CABINET TO REMOVE P.C.B.S

Figure 4-11 Replacing P.C.B.s — Cocktail

Page 27

| OPENING THE ATTRACTION PANEL | 1. UPRIGHT MODEL: REMOVE SCREWS AND LIFT ATTRACTION PANEL UP

O Turn the power to the game off.

O Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See Figure 4-12. Remove the top bracket and slide up the attraction panel. This exposes the speakers, the fluorescent light tube, and its mounting bracket assembly. To reinstall! the attraction panel, reverse this procedure. O The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.

WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered giass can tly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

O Replacing the fluorescent tube starter. See Figure 4-13. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. O Replacement of the fluorescent tube mounting bracket assembly. Be sure the power is off to the game. Disconnect it from its power cable. Remove the screws at its right and left hand sides which secure it and gently slide it out the front of the cabinet, being careful not to catch its power cable on anything. To reinstall the fluorescent tube mounting bracket assembly, reverse this procedure.

FLUORESCENT TUBE STARTER Figure 4-12 Opening the Attraction Panel — Upright

DO Replacing the speaker. Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attraction panel was. Reverse this procedure to reinstall the speaker. O To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. To reinstall the speaker, simply reverse this procedure.

  • THE COCKTAIL TABLE MODEL HAS NO BACK- LIT ATTRACTION PANEL.

1/4 TURN TO REPLACE

Figure 4-13 Replacing Fluorescent Tube Starter — Upright

Page 28
Scan of page 28

This page is a drawing, shown as the original scan.

Page 29

5-2 @ © O02 © NO. 303 — DOMINO MAN — UPRIGHT — FRONT

Page 30

NO. 303 — DOMINO MAN — UPRIGHT — FRONT — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0303-00902-00XF DECORATIVE HEADER PLEXI 0574-00903-0100 HEADER BRKT. RETAINER (2 REQ’D.) 0017-00101-0138 #8 x 5/8 TORX TAMPER RESISTANT SCREW (8 REQ'D) 0017-00009-0522 LONG ARM KEY T-20 (FOR ABOVE SCREW) 0537-00903-0058 GLASS CHANNEL — 6-15/16” LG. (2 REQ'D.) A595-0001 1-0000 HEADER LIGHT ASSY. — FLUORESCENT 0017-00009-0393 BLACK SPEAKER GRILL W/SLOTS (2 REQ’D.) 0017-00003-0430 6" x 9" SPEAKER — 4 OHM, 10W. (2 REQ'D.) 0017-00101-0127 #8-32 x 1-1/2 CARRIAGE BOLT (8 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (8 REQ'D.) 0508-00900-0000 19" TV. BEZEL 0508-00106-0000 BEZEL MTG. BRKT. (2 REQ’D.) 0303-00903-00XF MAIN VIEWING GLASS 0508-00108-0000 GLASS STOP BRKT. 0017-00101-0014 #8 x 1/2 SLT. HEX HD. SCR. (4 REQ'D.) 0303-00900-0000 DECORATIVE CONTROL SHELF OVERLAY A303-00012-0000 CONTROL SHELF PLATE ASSY. W/STRIKES. 0941-00103-0100 CONTROL SHELF MTG. BRKT. — RIGHT 0941-00103-0200 CONTROL SHELF MTG. BRKT. — LEFT 0555-00901-0000 PLASTIC LOCATING PIN (4 REQ'D.) 0017-00009-0534 LATCH CLAMP (3 REQ’D.) 0017-00101-0141 #8 x 11/16 UNSLOT. HEX HD. SCR. (6 REQ’D.) A982-00017-0000 CONTROL ASSEMBLY A303-00010-0000 CONTROL SHELF CABLE ASSV. 0017-00042-0260 PUSH BUTTON ASSY. — WHITE (2 REQ'D.) 0017-00042-0261 PUSH BUTTON ASSY. — GREEN (2 REQ'D.) 0017-00032-0093 PUSH BUTTON SWITCH W/HOLDER (4 REQ'D.) 0017-00103-0054 5/8-11 PAL NUT (4 REQ’D.) 0303-00906-0100 DECAL — LEFT 0303-00906-0200 DECAL — RIGHT (NOT SEEN) 0303-00901 -O0XF FORMED OVERLAY A090-00300-11BK U.S.A. 25¢ DOUBLE COIN DOOR A982-00015-0000 COIN DOOR CABLE ASSY. 0090-00002-04BK LARGE COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) 0935-00906-0100 KICK PLATE — 23” LG. (NOT SHOWN) 0017-00102-0048 3/8-16 x 2” LEG LEVELERS (4 REQ’D.) 0017-00103-0026 3/8-16 LEG LEVELERS HEX NUTS (4 REQ'D.)

5-3

Page 31

5-4 ee ne NO. 303 — DOMINO MAN — UPRIGHT — REAR ACCESS

Page 32

NO. 303 — DOMINO MAN — UPRIGHT — REAR ACCESS — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO.

A088-00013-0000 0894-00916-0000 0017-00101-0141 0636-00101-0000 0017-00102-0002 0017-00104-0014 0017-00003-0339

0017-00003-0439

A088-00016-0000 A082-90412-D000 0624-00902-0200 0624-00902-0500 0017-00101-0141 0017-00104-0037 A082-90910-E000 0017-00042-0014 0017-00101-0751 A945-00020-0000 A303-0001 1-0000 A082-90010-F000 A082-90913-F000 A082-91399-H000 0017-00042-0208 0017-00042-0253 0017-00101-0085 A950-00004-0000 A950-00006-0000 0950-00105-0000 0950-00104-0000 0950-00101-0060 0950-00900-0000 0017-00101-0142 0017-00104-0014 0017-00103-0018 A961-00007-0000 0961-00109-0000 0017-00042-0255 0894-00702-00XF 0017-00100-0037 A945-00019-0000 0017-00003-0430 DESCRIPTION

ON-OFF SWITCH & BRKT. ASSY. PLASTIC PULL & VENT (2 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ’D.) MONITOR RAIL (2 REQ'D.) 1/4-20 x 1/2 SLT. HEX HD. BOLT (4 REQ’D.) 7/8" DISH WASHER (4 REQ’D.) ELECTROHOME — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR (OR) WELLS-GARDNER — 19” COLOR DUAL SYNC. HORIZ. MTG. MONITOR INTERLOCK SWITCH & SPRING BRKT. ASSY. POWER SUPPLY P.C. BRD. ASSY. P.C. SUPPORT BRKT. — 10” LG. (2 REQ’D.) P.C. SUPPORT BRKT. — 6-1/2" LG. (2 REQ'D.) #8 x 11/16 UNSLOT, HEX HD. SCR. (7 REQ’D.) #8 WASHER (7 REQ’D.) DUAL POWER AMP P.C. ASSY. 1/8" SNAP BUSHING (4 REQ’D.) #5-40 x 1/4 PHIL. RND. HD. M.S. (4 REQ’D:) POWER CHASSIS ASSY. — 125VA., 115V. CARD RACK W/BOARDS ASSV. C.P.U. P.C. BOARD ASSY. SOUND P.C. BOARD ASSY. VIDEO GENERATOR P.C. BOARD ASSY. 1-1/8" P.C.B. SUPPORT (4 REQ’D.) DUAL LKG. P.C.B. SPACER (4 REQ’D.) #6 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.) COIN BOX ASSY. COIN BOX CRADLE ASSY. COIN BOX GOVER COIN BOX HANDLE COIN DEFLECTOR (2 REQ'D.) LARGE PLASTIC CASH BOX 1/4-20 x 1-3/8 BLACK RND. HD. BOLT (4 REQ’D.) 7/8" DISH WASHER (4 REQ'D.) 1/4-20 HEX NUT (4 REQ’D.) CASTER ASSY. (2 REQ'D.) WHEEL BRKT. (2 REQ’D.) PLASTIC WHEEL (2 REQ’D.) SHAFT (2 REQ'D.) 3/8" E-RING (2 REQ’D.) LINE CORD ASSY. — 115V. 6" x 9" SPEAKER — 4 OHM, 10W. (2 REQ'D.)

Page 33

NO. 303 — DOMINO MAN — UPRIGHT — REAR ACCESS — PARTS LIST (Continued)

ORDER BY PART NUMBER ONLY

ADDITIONAL PARTS LIST A151-00098-0000 BACK DOOR LOCK ASSY. 0017-00009-0490 5-5/8" SQR. VENT GRILL (4 REQ'D.) A515-00021-0000 MULTIFUNCTION SWITCH & BRKT. ASSY. A303-00009-0000 MASTER CABLE W/BRKT. ASSY. A303-00007-0000 HIGH VOLTAGE CABLE ASSY. A941 -00008-0000 LOW VOLTAGE CABLE ASSY. A968-00029-0000 VIDEO SIGNAL CABLE ASSY. 0968-005 10-0000 TOP — CARD RACK BLOCK 0968-0051 1-0000 BASE — CARD RACK SUPPORT BLOCK

5-6

Page 34

f NO. 303 — DOMINO MAN — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY.

NO. 303 — DOMINO MAN — UPRIGHT — HEADER FLUORESCENT LIGHT ASSY. — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

0595-00105-0000 FLUORESCENT BRKT. 0017-00003-0043 18" COOL WHITE FLUORESCENT LAMP 0017-00003-0445 LAMP LOCKS (2 REQ'D.) 0017-00031-0036 FLUORESCENT SOCKET (2 REQ'D.) 0017-00003-0412 FLUORESCENT STARTER HOLDER W/LEADS 0017-00101-0573 #6-32 x 1/2 PHIL. RND. HD. M.S. (4 REQ'D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ'D.) 0017-00003-0019 FLUORESCENT STARTER 0017-00003-0026 BALLAST 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.) A961-00042-0000 LINE FILTER ASSY.

Page 35

NO. 314 — DOMINO MAN — COCKTAIL — FRONT

5-8

Page 36

NO. 314 — DOMINO MAN — COCKTAIL — FRONT — PARTS LIST

ORDER BY PART NUMBER ONLY

PART NO. DESCRIPTION

0017-00009-0499 0314-00903-9000 0775-00104-00XF 0017~00101-0117 0314-00902-0000 0508-00901-0000 0017-00101-0017 0557-00900-0000 A314-06005-0100 A314-00005-0200 0017-00009-0393 0017-00009-0482 0017-00003-0460 0017-00003-0430 0017-00101-0136 0017-00103-0061 A090-00300-11BK A982-00015-0000 0090-00002-04BK 0017-00101-0121

A927-00019-0000 A962-00004-0000 A962-00005-0000 0962-00101-0000 0017-00101-0628 0017-00104-0022 0017-00103-0061 0017-00102-0048 0017-00103-0026 COVER GLASS — 32” x 22" x 1/4" ARTWORK UNDERLAY — DECORATIVE GLASS CLIPS (8 REQ’D.) #8 x 5/8 PHIL. TRS. HD. SCR. (16 REQ'D.) PLEXI-GLASS PLEXI-GLASS MTG. CLIPS (4 REQ’D.) #6 x 1/2” SLT. HEX HD. BLK. SCR. (4 REQ’D.) TV. BEZEL CONTROL SHELF ASSY. — PLAYER #1 CONTROL SHELF ASSY. — PLAYER #2 BLACK SPEAKER GRILL W/SLOTS (3 REQ’D.) SMALL SPEAKER GRILL (NOT SHOWN) 4” SQR. SPEAKER — 4 OHM, 10W. 6" x 9" SPEAKER — 4 OHM, 10W. #8-32 x 1-1/4 CARRIAGE BOLT (16 REQ'D.) #8-32 HEX NUT W/SEMS (16 REQ’D.) COIN DOOR ASSY. — U.S.A. 25¢ COIN DOOR CABLE ASSY. LARGE COIN DOOR FRAME #6-32 x 5/16 PHIL. TRS. HD. SCREW (3 REQ’D.) (MOUNTS COIN DOOR TO FRAME) COIN BOX ASSY. COIN BOX COVER ASSY. COIN BOX SIDE CHANNEL ASSY. — SHORT COIN BOX SIDE CHANNEL — SHORT #8-32 x 3/4 CARRIAGE BOLT (4 REQ'D.) #8 FLAT WASHER (4 REQ’D.) #8-32 HEX NUT W/SEMS (4 REQ'D.) 3/8-16 x 2" LEG LEVELERS (4 REQ'D.) 3/8-16 LEG LEVELER HEX NUTS (4 REQ’D.)

5-9

Page 37

5-10 none os one NO. 314 — DOMINO MAN — COCKTAIL — INTERIOR ACCESS

Page 38

NO. 314 — DOMINO MAN — COCKTAIL — INTERIOR ACCESS — PARTS LIST

ITEM

0921-00107-00XF 9017-00009-0534 0017-00101-0141 0017-00003-0450

0557-00100-0000 0017-00101-0642 0017-00104-0031 0017-00103-0061 0017-00102-0002 0017-00102-0052 0017-00104-0014 0017-00009-0514 0017-00101-0136 0017-00103-0061 0314-00901-0100 0314-00901-0200 A302-00015-0000 0510-00101-OOXF 0017-00101-0341 A982-00017-0000 A317-00010-0100 A317-00010-0200 0017-00032-0051 0017-00042-0303 0017-00032-0093 0017-00103-0054 0930-00104-0000 0017-00101-0025 0930-00904-0000 0017-00031-0044 0017-00003-0219 0017-00101-0555 A082-90412-D000 0624-00902-0100 0624-00902-0500 0017-00101-0141 0017-00104-0037 A082-90910-E000 0017-00042-0014 0017-00101-0751 A945-00020-0000 303-0001 1-0000 A082-90010-F000 A082-90913-F000 A082-91399-H000 0017-00042-0208 0017-00042-0253 0017-00101-0085 ORDER BY PART NUMBER ONLY

CATCH (2 REQ'D.) BASSICK CLAMP (2 REQ’D.) #8 x 11/16 UNSLOT. HEX HD. M.S. (8 REQ'D.) 19” COLOR DUAL SYNC. VERT. MTG. MONITOR — (WELLS-GARDNER) MONITOR MTG. BRKT. (2 REQ'D.) #8-32 x 1-1/2 CARRIAGE BOLT (4 REQ'D.) #8 FLAT WASHER (4 REQ’D.) #8-32 HEX NUT W/SEMS (4 REQ’D.) 1/4-20 x 1/2 SLT. HEX HD. BOLT (4 REQ’D.) 1/4-20 x 1” UNSLOT. HEX FLAT HD. BOLT (4 REQ'’D.) 7/8" DISH WASHER (8 REQ'D.) 2-1/2" HINGE (2 REQ'D.) #8-32 x 1-1/4 CARRIAGE BOLT (8 REQ’D.) #8-32 HEX NUT W/SEMS (8 REQ'D.) DECORATIVE OVERLAY — PLAYER #1 DECORATIVE OVERLAY — PLAYER #2 CONTROL PANEL WELDMENT ASSY. (2 REQ'’D.) BOTTOM PAN (2 REQ’D.) #6 x 1/4 PHIL. TRS. HD. SCR. (6 REQ'D.) CONTROL ASSY. (2 REQ’D.) CONTROL SHELF CABLE ASSY. — PLAYER #1 CONTROL SHELF CABLE ASSY. — PLAYER #2 SMALL RED BUTTON SWITCH ASSY. W/HARDWARE (2 REQ'D.) PUSH BUTTON ASSY. — GREEN (2 REQ'’D.) PUSH BUTTON SWITCH W/HOLDER (2 REQ'’D.) 5/8-11 PAL NUT (2 REQ'’D.) CONTROL PANEL LOCATING BRKT. (4 REQ’D.) #8 x 1/2 SLT. HEX HD. M.S. (16 REQ’D.) LIGHT SHIELD (2 REQ’D.) WEDGE BASE LAMP SOCKET (4 REQ'D.) #194 WEDGE BASE LAMP — 14V., .27A. (4 REQ’D.) #6-32 x 5/16 SLT. HEX HD. M.S. (4 REQ'D.) POWER SUPPLY P.C. BRD. ASSY. P.C. SUPPORT BRKT. — 12” LG. P.C. SUPPORT BRKT. — 6-1/2” LG. (2 REQ'D.) #8 x 11/16 UNSLOT. HEX HD. SCR. (7 REQ’D.) #8 WASHER (7 REQ’D.) DUAL POWER AMP P.C. ASSY. 1/8" SNAP BUSHING (4 REQ’D.) #5-40 x 1/4 PHIL. RND. HD. M.S. (4 REQ'D.) POWER CHASSIS ASSY. — 125VA., 115V. CARD RACK W/BOARDS ASSY. C.P.U. P.C. BOARD ASSY. SOUND P.C. BOARD ASSY. VIDEO GENERATOR P.C. BOARD ASSY. 1-1/8” P.C.B. SUPPORT (4 REQ’D.) DUAL LKG. P.C.B. SUPPORT (4 REQ'’D.) #6 x 5/16 SLT. HEX HD. SCR. (4 REQ’D.)

Page 39

NO. 314 — DOMINO MAN — COCKTAIL — INTERIOR ACCESS — PARTS LIST (Continued)

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

A775-00013-0000 FAN ASSEMBLY 0151-00081-0000 4" FAN 0775-00110-00XF FAN PLATE 0749-00106-00XF VENT SCREEN 0017-00101-0347 #6-32 x 1/2 R.H.M.S. (4 REQ'’D.) 0017-00104-0009 #6 EXT. WASHER (4 REQ'D.) 0017-00103-0005 #6-32 HEX NUT (4 REQ'D.) 0017-00101-0026 #8 x 5/8 SLT. HEX HD. M.S. (4 REQ’D.) ADDITIONAL PARTS LIST A088-00013-0000 ON-OFF SWITCH & BRKT. ASSY. A088-00014-0000 INTERLOCK SWITCH & BRKT. ASSY. A314-00009-0000 MASTER CABLE W/BRKT. ASSY. A942-00008-0000 HIGH VOLTAGE CABLE ASSY. A941-00008-0000 LOW VOLTAGE CABLE ASSY. A968-00029-0000 VIDEO SIGNAL CABLE ASSY. 0942-00902-0000 MONITOR SHIELD A927-00005-0000 HIGH BASE LEG KIT ASSY. — OPTIONAL 0968-00510-0000 TOP — CARD RACK BLOCK 0968-0051 1-0000 BASE — CARD RACK SUPPORT BLOCK

DOMINO MAN — CONTROL ASSEMBLY — ALL VERSIONS — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM PART NO. DESCRIPTION

A932-00022-0000 BALL & SHAFT ASSEMBLY 0017-00100-0025 1/4 E-RING 0921-00702-0000 STOP SPACER 0921-00902-0000 SLIDE PLATE A982-00019-0000 PIVOT PLATE WELD ASSY. 0017-00101-0637 #8-32 x 1" CARRIAGE BOLT (4 REQ’D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) 0932-00902-0000 GROMMET 0017-00101-0598 #8-32 x 5/16 SLT. HEX HD. M.S. (10 REQ’D.) 0962-00904-0000 SLEEVE 0017-00101-0527 #5-40 x 5/8 SLT. RND. HD. SCR. (8 REQ’D.) 0020-00202-0000 SWITCH PLATE (4 REQ’D.) A932-00009-0000 SWITCH ASSEMBLY (4 REQ'D.) A932-00012-00XF STOP PLATE & SWITCH BRKT. ASSY. 0932-00905-0000 WEAR PLATE 0921-00700-0000 ACTUATOR CONAMHAON=

Page 40

DOMINO MAN — CONTROL ASSEMBLY — ALL VERSIONS

Page 41

FRONT DOOR ASSEMBLY — U.S.A. 25¢

f/ / \ Ns ff H/ / aN

ff d’ * ?

Page 42

FRONT DOOR ASSEMBLY — U.S.A. 25¢ — PARTS LIST

ORDER BY PART NUMBER ONLY

ITEM | PART NO. DESCRIPTION

0090-00002-04BK DOUBLE ENTRY COIN DOOR FRAME 0017-00101-0121 #6-32 x 5/16 PHIL. TRS. HD. SCR. (3 REQ'D.) A090-00073-02BK DOUBLE ENTRY COIN DOOR W/DRESS PLATE 0017-00101-0123 #8 x 1/4 UNSLOT. HEX HD. SCREW (12 REQ’D.) 0017-00007-0019 KEY HOOK 0017-00103-0059 PUSH NUT (4 REQ’D.) 0090-00912-0000 COIN ENTRY PLATE — 25¢ (2 REQ'D.) A097-00005-0000 DOOR LOCK & KEY W/SCREW & NUT (OR) A097-00006-0000 DOOR LOCK & KEY W/SCREW & NUT 0090-00128-00XF DOOR TILT SWITCH BRKT. 0017-00005-0041 DOOR CAM A090-00095-0000 DOOR TILT SWITCH 0090-00126-03XF SWITCH BACK-UP PLATE 0017-00101-0525 #5-40 x 9/16" PHIL. HD. M.S. (2 REQ’D.) A090-00096-0000 DOOR TILT SWITCH & BRKT. ASSY. (ITEMS 9 & 11 THRU 13) 0090-00903-9500 25¢ WINDOW (2 REQ’D.) 0090-00143-00XF COIN PLEX RETAINER 0017-00003-0219 12 VOLT LAMP — G.E. #194 (2 REQ'D.) 0017-00031 -0048 WEDGE SOCKET W/BRKT. (2 REQ'D.) A090-00100-0000 BRKT. ASSY. 0017-00103-0084 #6-32 HEX NUT W/SEMS (4 REQ’D.) A090-00089-0000 COIN METER W/DIODE 0017-00101-0124 #6 x 1/4 UNSLOT. HEX HD. SCR. (4 REQ’D.) 0090-0091 1-0000 INSULATOR (2 REQ'D.) A090-001 12-0000 COIN CHUTE & INSULATOR ASSY. (2 REQ'D.) 0010-00134-0000 SPRING 0010-00181 -0000 SPRING 0017-00007-0083 1/8 x 1-5/8 ROLL PIN 0090-00129-00XF PIVOT POST 0090-00167-00XF PIVOT LEVER 0090-00182-00XF REJECT LEVER 0017-00100-0018 E-RING A090-00088-0000 REJECT LEVER ASSY. (2 REQ'D.) (ITEMS 30 THRU 33) A090-00105-0000 COIN ACCEPTOR FRAME ASSYV. (2 REQ’D.) 0017-00005-0003 COIN ACCEPTOR W/STRING CUTTER (2 REQ'D.) (OR) 0017-00005-0211 COIN ACCEPTOR W/ANTI STRING DEVICE (2 REQ’D.) (OR) 0017-00005-0214 COIN ACCEPTOR W/STRING CUTTER (2 REQ'’D.) A090-00064-0000 ANTI-PENNY DEVICE 0017-00101-0099 #6 x 1/4 SLT, HEX HD. M.S. (2 REQ’D.) 0090-00162-00XF COIN SWITCH MTG. BRKT. 0017-00005-0203 COIN SWITCH CHUTE 0017-00005-0195 COIN SWITCH 0010-00599-0000 COIN SWITCH WIRE 0017-00007-0015 PUSH-ON RING A090-00059-0400 COIN SWITCH & WIRE ASSY. (ITEMS 40 THRU 42) 0017-00101-0147 #4-40 x 3/4 PHIL. PAN. HD. M.S. (2 REQ’D.) A090-00077-0000 COIN GUIDE & SWITCH ASSY. (ITEMS 38 THRU 43) CMOMNANAWON=

Page 43

DOMINO MAN — POWER CHASSIS ASSY. — 125VA., 115V. — ALL VERSIONS

5-16

Page 44

DOMINO MAN — POWER CHASSIS ASSY. — 125VA., 115V. — ALL VERSIONS — PARTS LIST

ORDER BY PART NUMBER ONLY | rem | PART NO. DESCRIPTION 0945-00104-00XF CHASSIS A945-00029-0000 MTG. PLATE & BARRIER ASSY. 0945-00107-01XF STRAP (2 REQ’D.) 0017-00101-0123 #8 x 1/4 UNSLOT. HEX HD. SCR. (12 REQ'D.) MTO0-00101-A000 ISOLATION TRANSFORMER W/O SHIELD ASSY. — 115V., 50/60 HZ. 0017-00103-0061 #8-32 HEX NUT W/SEMS (4 REQ’D.) MTO00-00099-A000 POWER TRANSFORMER ASSY. — 115V., 60 HZ. 0017-00103-0084 #6-32 HEX NUT W/SEMS (4 REQ’D.) 0175-181T4-GXJK CAPACITOR — 3.5 M.F., 440V. 0017-00009-0535 CLAMP. 0017-00101-0565 #6-32 x 7/16 SLT. PAN HD. SCR. 0017-00103-0084 #6-32 HEX NUT W/SEMS

90017-00101 -0067#6 x 3/8 PHIL. PAN HD. SCR. (11 REQ'D.)

0945-00103-00XF PARTITION — LOCATED UNDER CHASSIS (NOT SEEN)

100945-00902-0000SNAP BUSHING (3 REQ'D.)
in|0017-00021-02972 POSITION CONNECTOR
12A945-00030-0100CONNECTOR & CABLE ASSY. #1
13A945-00030-0200CONNECTOR & CABLE ASSY. #2
14A945-00021-0000CONVENIENCE OUTLET ASSY.
150017-00101-0573#6-32 x 1/2 PHIL. RND. HD. SCR. (2 REQ'D.)

0017-00103-0084 #6-32 HEX NUT W/SEMS (2 REQ'D.) A945-00025-0000 FILTER ASSEMBLY — 125V. — UNDER CHASSIS (NOT SEEN)

160017-00021-0510TERMINAL STRIP
70017-00101-0140#4-40 x 5/16 PHIL. PAN HD. SCR. (2 REQ’D.)
180017-00003-0263SLO-BLO FUSE — 4A., 250V.

0017-00003-0005 FUSE — 2A., 250V. 0017-00003-0444 QUICK CONN. FUSEHOLDER (2 REQ’D.) — FOR ABOVE FUSES 0945-00816-1902 CAPACITOR — 100,000 M.F. 0945-00816-1901 CAPACITOR — 55,000 M.F. 0017-00104-0107 #10 FLAT WASHER (4 REQ'D.) 0017-00103-0081 #10-32 HEX NUT W/SEMS (4 REQ'D.) 0017-00009-0422 CLAMP (2 REQ’D.) 0017-00101-0758 #8-32 x 3/4 PHIL. RND. HD. SCREW (2 REQ'D.) 0017-00103-0061 #8-32 HEX NUT W/SEMS (2 REQ'D.) 0017-00101-0067 #6 x 3/8 PHIL. PAN HD. SCR. (6 REQ'D.) 0945-00904-0000 5 POSITION FUSE HOLDER 0017-00003-0263 SLO-BLO FUSE — 4A., 250V. 0017-00003-0217 SLO-BLO FUSE — 2.5A., 250V. (2 REQ’D.) 0017-00003-0007 SLO-BLO FUSE — 3A., 250V. (2 REQ’D.) 0945-00903-0000 FUSE HOLDER BARRIER A945-00022-0000 HEATSINK & DIODE ASSY. 0017-00101-0067 #6 x 3/8 PHIL. PAN HD. SCR. (2 REQ’D.) 0017-G0101-0780 #6 x 1/2 PHIL. PAN HD. SCREW (2 REQ'D.) 0017-00021-0629 5 POSITION TERMINAL STRIP — (UNDER CHASSIS) A945-00019-0000 LINE CORD ASSY. — 115v. (NOT SHOWN) A945-00030-0500 CONNECTOR & CABLE ASSY. 0017-00101-0660 #10-32 x 3/4 PAN HD. SCREW 0017-00104-0107 #10 FLAT WASHER 0017-00103-0081 #10-32 HEX NUT W/SEMS

Page 45

VI Technical Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.

General Suggestions correctly identifying the mmaffunction’s symptoms

The first step in any troubleshooting procedure is correctly identifying the mmaffunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A care~ fully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.

Harness Component Troubleshooting

Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example. your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate a little by turning the adjusting screw out a bit (see section on coin acceptor for more details). If the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. !f so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the termina! lug on the switch to the associated PCB trace. This will tell you if there is a continuous lineal! the way to the credit circuit.

Page 46

If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch. the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary

some from game to game, but no game’ will work on

line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine’s malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game’s harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply.

6-2 If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as weli, especially if there is a hum bar rolling up or down the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occurin areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices

removed the short, reconnect the devices one by one

until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control panel buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. In many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC tine LOW to GNDor to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.

Page 47

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.

CPU — central-processing unit. A computing system's “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.

ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM’s contain up to 16,000 bits of data to serve as the microprocessor's basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).

Introduction to the

Z-80 CPU

The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devicesa computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LS! microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors:

6-3

  • The Z-80 is fully software compatible with the popular 8080A CPU. . Existing designs can be easily converted to include the Z-80. . The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today. . For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
  • CPU (Central Processing Unit)
  • Memory
  • Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose I/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic.
Page 48

General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic and logical)

Subtract Increment

Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the controi signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.

Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.

MREQ <———J SYSTEM tora <+——_j CONTROL — AD «——_ wR «|

RSH «= —

HALT ~<«<——4

cpu wat ~—“_»} CONTROL < int = ——>} nmi |= —7

RESET ————»

BU: CONTROL 2-80 CPU

Z-80 PIN CONFIGURATION 38 ADDRESS

  • BUS

> DATA bee , BUS

Page 49

AoAis (Address Bus) Tri-state output, active high. Aj-A;s constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. |/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. Ay is the least significant address bit. During’ refresh time, the lower 7 bits contain a valid refresh address.

DoD, (Data Bus) Tri-state input/output, active high. Dy-D; constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.

My, (Machine Cycle one)__ Output, active low. M, indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-codes always begin with CBH, DDH, EDH or FDH. M1 also occurs with IORQ to indicate an interrupt acknowledge cycle. MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 1ORQ (Input/Output Request) Tri-state output, active low. The IORQ signal indicates that the lower half of the address bus holds a valid 1/O address for al/O read or write operation. An IORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while 1/O operations never occur during M, time. RD (Memory Read) _ Tri-state output, active low. RD indicates that the CPU wants to read data from memory or an I/O device. The addressed I/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device.

6-5 RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.

HALT (Halt state) Output, active low. HALT indicaies that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity. WAIT (Wait) Input, active low. WAIT indicates to the Z-80 CPU that the addressed memory or \/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU.

INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by I/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (IFF) is enabled and if the BUSRQ signal is not active. When the CPU_accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions). NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable interrupt request line has a higher priority than INT and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 00664. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WAIT cycles can prevent _the current instruction from ending, and that a BUSRQ will override a NMI. RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:

  • Disable the interrupt enable flip-flop
Page 50
  • Set Register | = 00
  • Set Register R =00u
  • Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and all control ouput signals go to the inactive state.

BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus, data bus and tri-state output control signals to go to a high impedance state so that other devices can control these buses. When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated. BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.

CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements.

6-6

Page 51

MCR II SYSTEM P.C. BOARD JUMPER OPTIONS

VIDEO GENERATOR P.C. BOARD

MANUFACTURER EPROM NO.

68764 MOTOROLA —_—=_ 68766

MOTOROLA

NUMEROUS MFR'S

NUMEROUS MFR'S JW#16 | SWH#17

#

# *

*

  • = CUT JUMPER WIRES WHERE THIS SYMBOL “*” APPEARS. # = LEAVE JUMPER WIRES IN WHERE THIS SYMBOL “#” APPEARS.

The above table illustrates the fact that the Video Generator P.C. Board used in the MCR II System has 8 jumper wires, the SUPER C.P.U. P.C. Board used in the MCR Il System has 19 jumper wires, and the Sound I/O P.C. Board used in the MCR II System has 2 jumper wires.

All of the above Boards can be used with a variety of different SETS of EPROM chips. However, these EPROMS are not all made by the same manufacturer

6-7 and do have some internal differences. So, in order to make them function properly in their respective P.C. Boards, certain jumper wires on these Boards have to be cut.

The above table tells you which jumpers to cut (depending on which EPROM set you're going to use) by showing a “*” under that jumper wire’s number. If there is NO “*" under a jumper wire's number, THAT PARTICULAR JUMPER WIRE tS NOT TO BE CUT.

Page 52

VII. Coin Door Maintenance

SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer's name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: COIN MECHANISMS, INC. 817 Industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150

COIN DOOR MAINTENANCE

METAL COIN ACCEPTOR MECHANISMS

Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.

TO REMOVE PUSH LATCHES DOWN

PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, IL 60106 Phone (312) 766-6781

. Remove the coin acceptor mechanism as shown in Figure 7-1. O Push down on the two spring loaded latches. O While holding the latches down, pull the top of the coin acceptor mechanism toward you. C Release the latches and lift out the coin acceptor mechanism.

PUSH MECHANISM IN

Figure 7-1 Removing and replacing coin acceptor

Page 53

4, Clean the magnet of all foreign particles. See Figure 7-2. O This may be accomplished by swinging the gate open as shown in the above figure.

  • Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes agood bushing cleaner.) O Also clean the pivot pin.
  • Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: Q Place the coin acceptor in boiling water for about ten minutes.
CAUTION: BE CAREFUL NOT TO BURN YOU! SELF.

O Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. Rinse the coin acceptor in clean boiling water. O Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.

NOTE: The reason we recommend using boiling water is that it evaporates faster than cold water and speeds drying time.

GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE

Figure 7-2 Cleaning the metal coin acceptor

  • To lubricate the coin acceptor: O Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 7-3. O Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
  • WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
  • Check the coin chute for obstructions such as: paper, gum, etc. 9, Reinstall the coin acceptor to the coin door. See Figure 7-1. C Place the two pegs at the coin acceptor's base into their retaining slots. Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.

APPLY POWDERED GRAPHITE HERE

CRADLE

Figure 7-3 Lubricating the metal coin acceptor

Page 54

SQUEEZE PINS TOGETHER TO UNLOCK SWING BOTH GATES OPEN

HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT

Figure 7-4 Opening the plastic coin acceptor

PLASTIC COIN ACCEPTOR MECHANISMS

The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.
  • Remove the coin acceptor mechanism(s) as shown in Figure 7-1. O Push down on the two spring loaded latches. O While holding the latches down, pull the top of the acceptor mechanism toward you. O Release the latches and lift out the mechanism.
  • Squeeze the two pins indicated in Figure 7-4 together to open the mechanism and break it down into its three basic parts. © Clean the mechanism in hot soapy water. It never rusts. O Rinse the mechanism in clean hot water and allow it to dry.

7-3 O Reassemble the mechanism (it never needs lubrication).

  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 7-5. CO Place the two pegs at the coin acceptor's base into their retaining slots. O Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.
NOTE: See Figure 7-6 for instructions on how to set the plastic coin acceptor mechanisms to either accept or reject Canadian quarters.
Page 55

ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.

SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S. AND CANADIAN QUARTERS.

<

TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.

Figure 7-5 Changing the plastic coin acceptor to accept American or Canadian quarters.

Page 56

PLEASE NOTE:

THE INFORMATION CONTAINED IN THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.

IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.

OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!

THANK YOU

Page 57

Color T.V.

Color T.V Monitor

Introduction: (How to use this section of your manual.)

This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a TV. set, and that means a complex doo-dad that means big buck repairs. This isn't necessarily so. This section of the manual will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!

If you want to understand how a monitor works, just read the “THEORY OF OPERATION” subsection. If you wish, you can follow along with the schematics. The information is presented in a very basic manner but more complete treatmeni of the subject can be found in the technical sections of bookstores.

If you want to attemptto repair your monitor, it would

be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings

8-1 and take them seriously. The more equipment you have the better, but a low cost Volt-Ohm-Milliameter can often, do the trick. Here are the steps to take:

  • Find the symptom that matches the problems your monitor has in the “SYSTEM — DIAG- NOSIS” subsection. Tne diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
  • Once you have the circuit that is causing the troubie, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
  • Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.

That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)

Page 58

Symptom Diagnosis

. Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). O Bad yoke. O Bad vertical output section. O Open fusible resistor in vertical section. 0 Bad height control. 0 Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). 0 Bad yoke. 0 Open width coil. O Open part in horizontal output section. . Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. B. Bad component in output circuitry. . Line too close with black spacing: A. Problem in vertical section causing poor linearity. . Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal.

. Colors missing; check: A. Interface color transistors. B. Color output transistors. C. Cracked printed circuit board. D. Color circuits. E. Video input jack. . Picture not bright enough: A. Weak emission from picture tube. (Turn horizontal sync off frequency and put brightness all the way up for about 15 minutes. Occasionally this cures the problem.) . Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission. . Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking controi set too high. . Increasing brightness causes an increase in size and poor focus, A. Weak high voltage rectifier or regulation (high voltage unit).

8-2 10.

11.

12.

13.

14,

15.

16.

17.

18.

19.

20. Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).

Vertical rolling: A. Vertical oscillator transistor, IC, or circuit. B. No sync from logic board.

Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A.). B. Vertical oscillator is not putting out the right wave form. Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference.

Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmetrical picture or sides of picture: A. Defective yoke.

No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit).

No brightness, high voltage present; check: A. Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. C. Focus voltage. D. Grid to cathode picture tube bias.

No high voltage; check: For AC input to the “flyback”. Horizontal deflection stages. Flyback transformer. Yoke. Power supply. moop>

No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.

Page 59

21.

23. Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).

Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.

Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor. B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.

. Can't adjust purity or convergence: A. Use a degausser to demagnetize the picture tube carefully following your degausser’s instructions. B. Picture tube defective. C. Metal foreign material is in picture tube shield. D. Nearby equipment is electromagnetically interferring. E. The poles of the earth are pulling off the purity. F. Poor focus or width of picture.

Guide To Schematic Symbols

THERMISTOR (POLARITY DOESN'T MATTER)

SYYY YW

INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)

(-) CATHODE

(+) ANODE

ZENER DIODE

8-3 IRON CORE TRANSFORMER (SUCH AS A FLYBACK)

aC am FUSE (POLARITY DOESN'T MATTER)

CATHODE (-)

ANODE (+)

DIODE

Page 60

COLLECTOR ae COLLECTOR a BASE ————- BASE ———~- EMITTER = EMITTER SS

NPN TRANSISTOR PNP TRANSISTOR

t VA

VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)

+

LINES ARE CONNECTED ELECTROLYTIC CAPACITOR

LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)

hw = GROUND

8-4

Page 61

Troubleshooting

Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit should be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:

  • Semiconductors (like transistors, diodes, and integrated circuits). Fusible resistors. Electrolytic capacitors. Resistors. Capacitors and coils. Always remember that a monitor can bite like a snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 18,000 volts, CAN BE KILLERS! Avoid handling power transistors (usually output transistors), yoke terminals, and other high power components when the monitor is on.
WARNING: That picture tube is a bomb! When it breaks, first it implodes, then it explodes. Large pieces of glass have been known to fly in excess of 20 feet in all directions. DO NOT carry it by the long, thin. neck. Discharge its voltage to ground by shorting the anode hole to ground. Use a plastic handled screwdriver, connect one end of a wire with an alligator clip at each end to chassis ground and the other end to the metal shaft of the screwdriver. Using ONE HAND ONLY (put the other in your pocket) and touching ONLY the plastic handle of the screwdriver (DO NOT TOUCH THE METAL SHAFT) stick the blade of the screwdriver into the anode hole. Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smaller the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hold a very ARON

8-5 healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It's better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handiing the picture tube.

To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconductive firm table like wood, NOT METAL, and take off all of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.

Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the control itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.

CAUTION:

Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.

First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their!eads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voitages at the leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a probtem with that device or a component connected with it in the circuit. The next step is to use the ohmmeter to narrow down the field of possible offenders.

Page 62

To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining on the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, anda short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. It is also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the ohmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there should be high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case some component is messing up the ohmmeter reading.

NOTE: DONOT leave soldering equipment on the leads too long since all semiconductors, especially integrated circuits, are easily destroyed by heat.

Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you. a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.

Theory of Operation

To understand what goes on inside the monitor, large general groups of circuits will be examined instead of laboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.

THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice,

constant, smooth voltage so that the monitor circuits

don't jump around, And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see a small, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.

THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where the video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.

Page 63

An interesting aside is that our sync is composite negative sync. That means two things:

  • The sync is a negative going wave form.
  • There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second {or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.

VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can’t see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the sync as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit 1C501 for its sync section. Wells Gardner uses HA11423 and Electrohome uses HA11244. These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke’s vertical coils at 60 times a second.

Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal line means a problem with the vertical coils of the yoke or anything from the vertical output section on back to the oscillator.

8-7 The horizontal section is very. similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn’t going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in acar and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator’s frequency must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a large power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.

THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can’t meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontal output transistor. The “flyback” jacks up its input voltage and puts out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to make it asmooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 18,000 VOLTS ON IT AND IT CAN KILL YOU!

The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voltage. So in a way, the high voltage “flyback” is like a second power supply.

COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signals going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green.

Page 64

The blue doesn't have one. In the emitter part of each transistor is another variable resistor that is the cut off control. These controls vary the amount of amplified AC signal that goes to the cathodes of the picture tube. The more signal, the more color. The bases of each of these transistors are connected together and are all connected to the blanking and beam limiting transistors which are in the interface section. The beam limiter helps contro! the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don't show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.

PROTECTION CIRCUIT — To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a circuit senses the higher power supply voltage, and using a transistor, turns off the horizontal oscillator. Since the horizontal oscillator doesn't work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don’t be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner's 1C501 and emitter of X04 for the Electrohome monitor. Here are the voltages you should receive: Wells Gardner = 130VDC

Electrohome 120VDC

The best place to measure this voltage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, aol The GO7-FBO or GO7-902, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.

THE PICTURE TUBE (OR CRT) — The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. The cathode can arc or short to the heater resulting in no picture and a defective picture tube. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode.

After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head forthe green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.

Differences Between Monitors

The easiest way to identify the brand of monitor you are working with, assuming you can't find the brand name written on it anywhere, is to check the color of the suction cup type insulator that houses that dangerous anode plug on the CRT. Both monitors use a red wire but the Wells Gardner anode cup is BLACK while the Electrohome anode cup is LIGHT GRAY. Unfortunately, “call-out-numbers” for parts, circuit layout, and even circuit design are similar enough to confuse the average observer. Let's say you have an Electrohome that isn't working. No problem. You can scavenge parts from an old broken up one that you may have around. Now let's say you have a Wells Gardner that isn’t working. STOP! This could be a problem. There are3 different types of Wells Gardner K4900 SERIES monitors in the games. Here are ways to identify them. K4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Control but this area is jumpered with a small wire instead. K4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There IS a Vertical Damping Control next to the Vertical Hold Control. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the

Page 65

screen. Moving the Control may distort the top part of your picture (or the side, depending onthe game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size. K4956 (3rd TYPE) — This monitor is identical to the K4906 WITHOUT the Damper Control EXCEPT the picture tube is vertically mounted and there is an additional small P.C. Board mounted on the monitor where the yoke plugs in. This monitor is used on some Cocktail Table games where the picture has to flip for the second player. Generally speaking, some games flip the picture image via the logic board programming but this monitor is used in games that flip the picture image via generation of a small signal voltage which is sent to the extra P.C. Board on this monitor. This signal voltage causes relays on this extra P.C. Board to flip the picture by reversing the horizontal and vertical signals to the yoke pins. What kind of problems can this extra P.C. Board cause? If the relays become defective, the picture won't flip. If the P.C. Board gets cracked you may have a horizontal line on the screen, a vertical line on the screen, or maybe just a dot in the center of the screen. Of course, the logic board could be defective and not sending the signal to flip the picture. In any case, some people feel that using relays is cheaper, simpler, and more reliable, so this is an advantage.

CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13” Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control. On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this control does adjust the brightness, but it is used to set the CRT bias and is adjusted at the factory. When Wells Gardner sets it, they mark the position with a black mark on the knob. If you move it, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls.

Parts Interchangeability

Some parts can be interchanged on all of the monitors. Here are the rules:

  • You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance. You CAN swap any capacitor between monitors that has the same capacitance and voltage rating. You CAN swap many of the parts between the 19” and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier. You CANNOT swap any picture tubes between monitors!! In the past you could, but Wells Gardner is now using a new monitor. When 4.

8-9 ordering a replacement picture tube, ALWAYS SPECIFY THE PICTURE TUBE NUMBER! You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (GO7- 904) monitor “flyback”. In fact, there is even a 19 inch Etectrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback”. NONE OF THESE ARE INTER- CHANGEABLE! ! You CAN change any of the parts between the G07-904 and GO7-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube. If there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.

Page 66

Power Supply Voltage and Symbols Symbol | Voltage

® 15V Vert. Osc. ‘Sync Blanking CRT Cut-Off Operating Circult

Horiz. Osc. Horz. Drive Horz. Output Vert. Output e 130V

Video Output

  • 175V

Q351 COLLECTOR

1VIDIV 200uSECIDIV 20VIDIV 10vSEC/DIV

‘TP-31 DC COUPLED 1402-3 BOTTOM LINE=0 VDC

2VIDIV 200MSEC/DIV SVIDIV 20uSECIDIV 19” COLOR MONITOR SCHEMATIC DIAGRAM

MODELS 19K4901, 19K 4906, 19K4951, 19K4956

SERVICE TECHNICIAN WARNING X-RAY RADIATION PRECAUTION:

THIS PRODUCT CONTAINS CRITICAL ELECTRICAL AND MECHANICAL PARTS ESSENTIAL FOR X-RAY RADIATION PROTECTION FOR REPLACEMENT PURPOSES, USE ONLY TYPE PARTS SHOWN IN THE

PARTS LIST.

O.5/DIV SMSEC/DIV

O.5IDIY 20u SECIDIV

CAUTION: FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL COM- PONENTS ONLY WITH MANUFAC. TURER’S RECOMMENDED PARTS. AVERTISSEMENT: POUR MAINTENIR LE DEGRE DE SECURITE DE L'APPAREIL NE REMPLACER LES COMPOSANTS DONT LE FONCTIONNEMENT EST CRITIQUE POUR LA SECURITE QUE PAR DES PIECES RECOMMANDEES PAR LE FABRICANT.

1.C. 301, PIN 3

1VIDIV SMSECIDIV

‘TP82

20VIDIV SMSECIDIV

LC. 301, PIN 13,

1VDIV 200uSEC/DIV F

AVIDIV 20u SECIDIV

TP.31, AC COUPLED

1VIDIV 200uSECIDIV

NEGATIVE SIDE OF C303

2VIDIV SMSECIDIV LC, 301, PIN 15

2VIDIV 10uSECIDIV

F

agg eeoersenseenemameooreg

<= tetramer

1VDIV 2MSECIDIV 2a cme

° "cas be: 301 v S38, anaee aro 10K aT a ea jt (eee) ot ‘hy case Patsy

foooee Ble a or F aet 9381 HOR. DRIVE axe) 28¢24620K . | ESCzEIOBK R360

poem gaa) 9.402 RED OUT GREEN OUT OSCILLOSCOPE WAVEFORM PATTERN The waveforms shown are as observed on the wide band oscilloscope with the monitor turned to a reasonably strong signal and a normal picture. The voltages shown. on each waveform are the approximate peak amplitudes. If the waveforms are observed on the oscilloscope with a poor high frequency response, the corner of the pulses will tend to be more rounded than those shown and the amplitude of any high frequency pulse will tend to be less.

9403 etude out 2SC2068.8/.BEK 2SC2068L.8/L BBK 2SCZ068L 8 ERK| 2SCISISBYC/CVE 2SCIBSI4BVCLVC 2SCISISBVC/CVC

5rSP 2) ea loveTr22

Feet

(E-DRIVE IRCUTOFF] [G.cUTOFF

te gor * # sync amp vos Hose °" f— ser Lt a313 : et R385 che 33K oe) a nae? Spifeos

2 Lsgore. Sage =r eeae oy | 9860 A303 use aS (HOR'SIZE]

K4901D, K4906D, K4951D 5833 K4956B 8-10

Page 67

REPLACEMENT PARTS LIST MAIN BOARD (CONT)

This monitor contains circuits and components included specificallyRet. No.Part No.DescriptionRet. No.Part No.Description

for safety purposes.

For continued protection no changes should be made to the originalCAPACITORS (CONT.)SEMICONDUCTORS (CONT)
on parts list should be replaced with exact factory replacement parts.4 C502202X7050-2821800 pF, S00V Cerartic208200x3181-523Transistor (NPN) 28C1818GR
The use of substitute parts may create a shock, fire, radiation or other4 C503202X7810-2142200 pF, 125V CeramicQ209200X3181-523Transistor (NPN) 2SC1851GR
hazard. Service should be performed by qualified personnel only.4504202X7810-2142200 pF, 125V CeramicQ210200X3181-523Transistor (NPN) 2SC1851GR
C505203x0220-075560 uF, 200V ElectrolyticQ301200X3181-523Transistor (NPN) 2SC1851GR
C506203x0040-03422 uF, 160V Electrolytic302200X3207-306Transistor (NPN) 28C2073LBGL2
507203X0041.05747 uF, 160V ElectrolyticQ303200X3207-306Transistor (NPN) 28C2073LBGL2
MAIN BOARD701203X0019-0921000 uF, 25V Electrolytic9351200X3248-217Transistor (NPN) 2SC24828K
c702203X0634-06110 uF, 100V Electrolytic9352200X4589-802Transistor (NPN) 2508988.
DescriptiRet.Ceci NeDeousipthC703202X7050-2481000 pF, 500V CeramicAk 'c301200K2300-083Ic HAtT423
Ref. No.Part No.escriptionief. No.artNo.escription:i4x:4)iTTR381

SEMICONDUCTORS

0203201x2010-159Diode, 182076-27
RESISTORSRESISTORS (CONT.)204201X2010-159Diode, 1$2076-27LastTROHSEORMERS & ant =
R201203X6500-6451K Ohm, 5%, 1/4W CarbonR369203X5602-329680K Ohm, 5%, 1/2W Comp.0205201X2010-159Diode, 1$2076-271352201X5000.083Coll (ee ead
R202203X6500-52330 Ohm, 5%, 1/4W CarbonR370203X6501-00233K Ohm, 5%, 1/4W Carbon206201X2010-159Diode, 182076-27L701611X0004.007Coil’ Adg.
R203203X6500-405100 Ohm, 5%, 1/4W CarbonR371203X9014-5841K Ohm, 5%, 1W Metal Oxide0207201X2010-158Diode, 182076277351202X1300-080Transformer, Hor. Drive
R204203X6700-327100 Ohm, 5%, 1/2W CarbonR372203X9101-11912K Ohm, 5%, 1W Metal Oxide0208201X2010-159Diode, 1$2076-27Ak 1382200X9720-901HY-UaltTi
R205203X6700-421270 Ohm, 5%, 1/2W CarbonR375203X6700-7636.8K Ohm, 5%, 1/2W Carbon209201X2010-159Diode, 1S2076-27
R206203X6500-540390 Ohm, 5%, 1/4W CarbonR376203X9104-404270 Ohm, 5%, 2W Metal Oxide0301201X2010-165Diode, ISS81MISCELLANEOUS
R207340X2201-934200 Ohm, 5%, 1/4W CarbonR377203X6500-447150 Ohm, 5%, 1/4W Carbon0302201X2010-159Diode, 1$2076-27
R208203X6500-540390 Ohm, 5%, 1/4W CarbonR378203X6500-88610K Ohm, 5%, 1/4W Carbon0303201%2010-159Diode, 1$2076-27AFSOI204X7 120-073Fuse, 4 Amp. 125V
R209340X2201-934200 Ohm, 5%, 1/4W CarbonR379203X6500-88610K Ohm, 5%, 1/4W Carbon0304201X2120-009Diode, RH-IV3402206X5008-632Recep W Wire 3P-M-BG
R210203X6500-540390 Ohm, 5%, 1/4W €arbonR380203X6500-8658.2K Ohm, 5%, 1/4W Carbon0305201X2120-000Diode, RH-IVP201204x9600-466Plug, PWB 3P-J
R211340X2201-934200 Ohm, 5%, 1/4W CarbonR381203X6500-7242.2K Ohm, 5%, 1W Metal Oxide0306201X2010-159Diode, 1$2076-27P202204X9601-477Plug, PWB 6P-Q
R214203X6500-645,1K Ohm, 5%, 1/4W CarbonR383203X9014-387150 Ohm, 5%. 1W Metal OxideADs501201X3120-216Diode, RM-1AVPaot204X9600-298Plug, PWB 4P-8
R215,203X6501-126100K Ohm, 5%, 1/4W CarbonR502203X6500-88610K Ohm, 5%, 1/4W Carbon4 0502201X3120-216Diode, RM-1AVPS01Posenoe ela ye
R216203X6500-6451K Ohm, 5%, 1/4W CarbonR503204X1700-535150 Ohm, 5%, 15W Metal Oxideened201%3120-216Diode, RM-1AVPeot204x9600-ug, Pa
R217203X6500-405100 Ohm, 5%, 1/4W CarbonR504203X9014-26747 Ohm, 5%, 1W Metal Oxide4.0504201X3120-216Diode, RM-1AVTHSO1201X0100-112Thermistor
R218203X6500-6451K Ohm, 5%, 1/4W CarbonR505203X6501-2092.2K Ohm, 5%, 1/4W Carbonsoebebeaoe aaa
R219203X6501-126400K Ohm, 5%, 1/4W CarbonR506203X9104-105,15 Ohm, 5%, 2W Metal OxideRM
R220203X6500-645,1K Ohm, 5%, 1/4W CarbonR507203X5602-185330K Ohm, 5%, 1/2W Comp.0701201X2130-234Diode, RU-2Veee ASSEMBLY PARTS
R221203X6500-405100 Ohm, 5%, 1/4W CarbonAwREO1204X 1625-0583.3 Ohm, 5%, 10W WW0702201X2120-009Diode, RH-1V~A%88x0138-50619VLTP22 Pix Tube
R222203X6500-7623.3 Ohm, 5%, 1/4W CarbonR701203X9105-1412.2 Ohm, 5%, 2W Metal Oxide201200X3181-523Transistor (NPN) 2SC1815GR.205X9800-158.Lateral/Purity Assembly
R224203X6500-16910 Ohm, 5%, 1/4W CarbonR702203X6206-4412.2 Ohm, 5%, 1/2W CarbonQ202200X3181-523Transistor (NPN) 2SC1815GRAx W 202X1111-201Yoke Deflection
R225203X6500-16910 Ohm, 5%, 1/4W CarbonvR201204X2070-0722K Ohm-B Semi-Fixed203200X4056-260Transistor (PNP) 2SA562-Y-TM204X9301-255CRT Socket;
R226303x6500-16940 Ohm’ 5%. 1/4W CarbonR301204X2070-0845K Ohm-B Semi-Fixed0204200X4056-260Transistor (PNP) 25A562-Y-TM291X5004-262Automatic Degaussing Coil Unit
R227203X6501-04447K Ohm, 5%, 1/4W CarbonVR303204X2070-055500 Ohm-B Semi-Fixed2205200X4056-260Transistor (PNP) 2SA562-Y-TM
R228203X6500-645,1K Ohm, 5%, 1/4W CarbonR351204x2070-072,2K Ohm-B Semi-Fixed
R229203X6700-421270 Ohm, 5%, 1/2W CarbonR352204X2070-0722K Ohm-B Semi-Fixed
R230203X6500-863,8.2K Ohm, 5%, 1/2W Comp.
R231203X6500-863,8.2K Ohm, 5%, 1/2W Comp.
R232203X6500-863,8.2K Ohm, 5%, 1/2W Comp.
R233,203X6500-468180 Ohm, 5%, 1/4W Carbon
R234340X2820-93482 Ohm, 5%, 1/4W CarbonCAPACITORS
R235340X2820-93482 Ohm, 5%, 1/4W Carbonc201203x0014-0884000 uF, 16V, ElectrolyticNECK BOARD
R236ee82 vite ae {aSarbenC202202X7200-064330 pF, 500V, Ceramic
8301203x6500-270 Ohm,5%, 1/4WCarbonC203,202X7200-043220 pF, 500V, Ceramic
R302203X6500-863,8.2K Ohm, 5%, 1/4W CarbonC204202X7200-043,220 pF, 500V, CeramicRESISTORSyCAPACITORS,
R303203X6500-8638.2K Ohm, 5%, 1/4W Carbon6205203X0014-076470 uF, 16V, ElectrolyticRat203X6000-729220 Ohm, 5% 1/4W Carbon401202X7050-2691200 pF, 500V Ceramic
R304203X6500-7242.2K Ohm, 5%, 1/4W CarbonC206203X1810-1490.1 uF, 125V MylarRa02203X6500-540390 Ohm, 5% 1/4W CarbonC402202X7050-2481000 pF,.500V Ceramic
305203X6500-8426.8K Ohm, 5%, 1/4W Carbon207349X2232-109022 uF, 100V MylarR403203X6000-661820 Ohm, 5% 1/4W CarbonC403202X7050-2481000 pF, 500V Ceramic
R306203X6003-2017.5K Ohm, 2%, 1/4W CarbonC301203x0014.065330 uF, SOV ElectrolyticR404203X6000-729220 Ohm, 5% 1/4W Carbonaod202X7050-2821500 pF, 1.5KV Ceramic
R307203x6500-825,5.6K Ohm, 5%, 1/4W Carbon6302203X1600-5630.033 UF, 50V MylarR405,203X6500-540390 Ohm, 5% 1/4W CarbonC405202X7050-483,0.01 uF, 500V Ceramic
309203X6500-96522K Ohm, 5%, 1/4W CarbonC303203X0629-0373.3 uF, 50V ElectrolyticA068:203x6000-681820 Ohm, 5% 1/4W Carbon
310203X6500-98839K Ohm, 5%, 1/4W CarbonC304203X1600-3660.068 pF, 50V MylarR407203X6000-729470 Ohm, 5% 1/4W Carbon
R311203X6500-7623.3K Ohm, 5%, 1/4W Carbon6306203xX0412.0122.2 uF, 16V TantalR408203X6000-998270 Ohm, 5% 1/4W CarbonSEMICONDUCTORS
R312203x9014-7414.7K Ohm, 5%, 1/4W CarbonC307203X 1600-6340.033 uF, 50V MylarRé09203x6000-661820 Ohm, 5% 1/4W CarbonQ401200X3206-800Transistor (NPN) 2SC2068LB
3313204X1450-5371K Ohm, 5%, 5W Carbon308203x0025-1743.3 uF, 50V ElectrolyticR410203X9104-82415K Ohm, 5% 2W MO. Forming402200X3206-800Transistor (NPN) 28C2068LB
314203X6500-481220 Ohm, 5%, 1/4W CarbonC309203X1207-1000.068 uF, 100V PPRatt203X9104-82415K Ohm, 5% 2W M.O. Forming403200X3206-800Transistor (NPN) 2SC2068LB
315203X6500-16910 Ohm, 5%, 1/4W Carbon310203x0629-06110 uF, 100V ElectrolyticRa12203X9104-82415K Ohm, 5%2W M.O. Forming
316203X6500-7623.3K Ohm, 5%, 1/4W CarbonCatt203X0041-02540 uF, 160V ElectrolyticR413203X6000-9982.7K Ohm, 5% 1/2W Comp.
317203X6700-10712 Ohm, 5%, 1/2W CarbonC312202X7050-2481000 pF, 500V CeramicRaa203X6000-9982.7K Ohm, 5% 1/2W Comp.MISCELLANEOUS
318203x6500-540390 Ohm, 5%, 1/4W Carbon6313203x0040-05247 uF, 160V ElectrolyticRAIS203X6000-998,2.7K Ohm, 5% 1/2W Comp.a206x5009.296RECEP W Wire 4P-€
203X6500-6451K Ohm, 5%, 1/4W CarbonC314203X1201-2650.033 uF, 200V PPRae203X9105-1542.2 Ohm, 5% 2W Metal Oxideasoaxosoo.eePoeOwe eek
203X6501-002,33K Ohm, 5%, 1/4W CarbonC315203x0629-0231 uF, 50V ElectrolyticR419203X6500-7412.7K Ohm, 5% 1/4W Carbonaoaonaxeene estPur Pn tPD
3321203X6501-224270K Ohm, 5%, 1/2W Carbon6351203x0629-0231 uF, 50V Electrolytic420203X6500-7412.7K Ohm, S%6't4W Catbon:P701204X9601-020Plug, PWB 4P-E
2922203X6500-88610K Ohm, 5%, 1/4W Carbon352203X06 19-04547 uF, 25V ElectrolyticRa21203X6500-7412.7K Ohm, 5% 1/4W Carbon5
R961203X6500-88640K Ohm, 5%, 1/4W Carbon0353203X1190-0150.0082 pF, 50V Mylar-PPvr4o1204X2115-014500 Ohm, -B Semi-Fixed
R382203X6500-7853.9K Ohm, 5%, 1/4W CarbonC354203X0619-04547 uF, 25V ElectrolyticVR402204X2115-014500 Ohm, -B Semi-Fixed
R353203X6501-08868K Ohm, 5%, 1/4W CarbonC355203x 1600-3660.0068 pF, 50V MylarR403204X2115-0065K Ohm, -B Semi-Fixed
A384203X6500-7623.3K Ohm, 5%, 1/4W Carbon356202X7050-4830.01 uF, 500V CeramicVR404204X2115-0065K Ohm. -B Semi-Fixed
R355203X9205-1436.8K Ohm, 5%, 3W Metal Oxide359202X8065-606100 pF, 500V CeramicR405204X2115-0065K Ohm, -B Semi-Fixed
R958203X5601-87856K Ohm, 5%, 1/2W CarbonC360202X7050-3660.0033 pF, 500V Ceramic
360203X6500-561470 Ohm, 5%, 1/4W Carbon361202X7050-4830.01 uF, 500V Ceramic
361203X6500-88640K Ohm, 5%, 1/4W Carbon362202X7203-0320.01 uF, 50V Ceramic
203x9014-6451.8K Ohm, 5%, 1W Metal OxideAwC363203X1270-9118700 pF, 1.5 KV PP
204x 1527-7513.9K Ohm, 5%. 7W Metal OxideC365203X1201-2650.33 uF, 200V PP
R364203X6500-24622 Ohm, 5%, 1/4W CarbonC366203X0019-02622 uF, 28V Electrolytic
R365203X6501-00233K Ohm, 5%, 1/4W CarbonC367202x8065-1626 pF, 500V Ceramic
R367203X6500-88640K Ohm, 5%, 1/4W Carbon368202X7203-0320.01 uF, 50V Ceramic
R368203X5602-185330K Ohm, 5%, 1/2W Comp.C372203X1207-1250.1 uF, 100V PP

8-12 8-11

Page 68

Buus oreo RED X101 ra xio2 ond XIOS VICEO AMP, 2SCasac 4 ond XI06 VIDEO AMP 25A673C WEEKS AGS pre OUTPUT 280261! or 2SCI5I4 Bae vas

|areara|

1x30! 302,808 X308 [28C484C or eaci68s

Bhiosa, asciasa FoWR REARS. X901 POWER DRIVE 25C2688 X902 ERROR AMP 2SC1890 ween tive n seme bed x308 iL x306,

AcIZ0V 80Hi/50H2 10% Tres Deore eT 77 |

; bid ae a.aite8 Acoze

i T404 ovo eae cur we vm 7 sia i

25C454¢ or 2sci685 28C26iI or 28C26I08K 250869 or 250820, aa

00-4147-04 G07-CBO Schematic Notes Unless otherwise specified Resistance: (Q) (K-*KQ, MM), 1/4 (W) carbon resistor Capacitance: 1 or higher-» (pF), less than 1 (yF) working voltage -> 50 (V) ceramic capacitor Inductance: (v H) x71 Sib wee Electrolytic Cap: Capacitance Value (y F)/working voltage (V), vet bes im NP — non-polar (or bipolar) electrolytic cap. tna ASSY cat oie Refer to the parts list for additional component information. ——_ —— ——_—. =o —— 2 indicates test point connection XTOI XRAY PROTECTOR RessP WE, escosrv SSoe08 or so ausaoaee oh indicates Chassis ground unless otherwise specifiec Hz indicates cycles per second For safety purposes (and continuing reliability) aA replace all components marked with safety syrnbo! with identical type.

NOTE: FR — fusible resistor -—¢—

Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) $U3030A (R113 = R3113)

Page 69

REPLACEMENT PARTS LIST - ELECTROHOME 19”” MONITOR

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics important to safety. DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR: Carbon ResistorC Cap.
Comp. R: Composition ResistorM Cap
OM R: Oxide Metal Film ResistorE Cap.
VR: Variable ResistorBP E Cap.

MF R : Metal Film Resistor

CMF R: Coating Metal Film ResistorMM Cap.
UNF R: Nonflammable ResistorPP Cap.
FR: Fusible ResistorMPP Cap.

PS Cap Tan. Cap. Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

SERVICE REPLACEMENT PARTS LIST

Symbol Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass'y Purity Shield Ass’y Part Number SU-1133A SU-3032A 07-220083-03 Outside of the P.C.B. Ass'y Symbol Description Picture Tube 19” A A\Deflection Yoke PC Magnet A AsFlyback Transf. iN AHVR ROS UNF Resistor 2200,25W K C04 C Capacitor 150pF, AC1.5KV x01 Si. Transistor x02 Si. Transistor sc Screw #8-%, sc Screw % x % Pix Tube Mtg. (4) WA Pyramida! Lock Washer (4) Nut Retainer, Pix Tube Mtg. (4) Clip — P.C.B. Support Standoff Wire Terminal (Gnd. Strap) Terminal Lug (Gnd.) Groundstrap Assy. Grounding Spring Wire Hook (Gnd. Strap) Purity Shield Holddown Clamp Support Brkt. RH Support Arkt. LH Chassis Base Yoke Wedge (3)

Purity Shield Ass’y. Parts List

Symbol Description Degaussing Coil 0911, D912 Rectifier 1 Amp 600V (2) Pin Terminal (2) Pin Terminal Housing Purity Shield (2 pes.) Purity Shield (2 pes.) C911 Capacitor 100nF 10% 400V R921 Resistor, Wirewound 332, 4W Fire Retardent Term. Strip 4 Lug

CRT Socket P.C.B. Ass’y (SU-3032A) Parts List

Resistors Symbol Description

R3105VvR 200
R3106VvR 200
R3113VvR 5K
R3114vR 5K
R3115VvR 5K
R3116OMR 10KQ2W J
R3117OMR 10KQ2W J
R3118OMR 10K Q2W J

R3119 Comp. R 3.3Ki2%W K R3120 Comp. R 3.3KQ%WK C3121 Comp. R 3.3KQ2%W K

Capacitors Symboi Description C3107 E Cap. 10uF 250VA 3108 C Cap. 1000pF DC1400v P

Coils Symbol Description 13101 Peaking Coil Part Number 17-7198-03 A29779-D = 21-141-01 A75034-B = 29-32-01 A29951-B A46600-A QRF258K-221 QCZ0101-005 2SD870 2SC1106A 31-610818-06 31-601418-12 33-255-01 33-494-01 33-629-02 33-670-010R-02 34-228-93 34-33-04 34-574-02 35-212-03 35-3053-02 35-2348-01 35-3890-01 35-3890-02 38-449-02 39-1233-01

Part Number 21-1007-30 28-22-27 34-708-01 34-709-01 35-3847-01 35-3847-02 48-171544-62 42-113301-03 34-492-09

Part-Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRG029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS3EA-106 QCZ9001-102M

Part Number QQL043K-101

Page 70

Semiconductors Symbol X3101 X3102 X3103

Miscellaneous Symbol A Description Si, Transistor Si. Transistor Si. Transistor

Description ASCRT Socket

Main PCB Ass’y (SU-1133A) Parts List

Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 AFR1401 4A1503 R1504 R1509 R1512 R1514 R1515, R1522 R1523 R1528 R1534 VR1501 AR1703 A\R1704 ASR1901 R1902 R1903 R1904 R1905 AQ 1908 AXR1909 R1910 AXFR1901

Capacitors Symbol C1301 C1402 C1407 C1411 C1412 C1508 AC1512 AC1513 ACI514 C1515 C1520 C1523 1524 AC1531 AC1532 C1904 1905 Descripti: Vv Vv CMF om om om Vv AF A\CMF Vv OM OM om CMF CMF OM OM ZN ZN A\CMF ACMF AsPosistor UNF CMF OM OM AXCMF Vv AXCMF AF D R R R R R R R R R R R R R R R 6892W J R R R R A

R R R R R R R R ion 2002 2002 6.8Q1W J 3.3K Q1W J 2.7K QW J 12KQ2W J 10KQ 6822W K 11.8KQ. “AW +1% 5K 10KQ2W J 8.2KQ2W J 820022W J 8.201W J 4.701W J

39091W J

392%2W +1% 7.68K2 %4W +1%

20Q7W K 4.723W J 10KQ2W J 18K Q1W J 47Q.2W +1% 2KQ 2.74K QW +1% 2202%W K

Description BPE Tan. E E E PP APP APP Ape PP BPE E M APP App E E Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. Cap. . 3.3uF 50V A . 2.2uF 16V K . 4.7UF 6.3V A . 100uF 160V A . 3.3uF 160V A . 5600uF SOV J . 2000pF DC1500V J . 2000pF DC1500V J . 2000pF DC1500V J . 0.53uF DC1200V J . 3.3uF 50V A . 1UF 160V A . 0.1UF 200V K . 2000pF DC1500V J . 1500pF DC1500V J

. 10uF 250V A Part Number 28C1514VC 2SC1514VC 28C1514VC

Part Number A76068

Part Number QVZ3230-002 QVZ3230-007. QRX019J-6R8 QRG019J-332 QRGO19J-272 QRG026J-123Z QVZ3230-014 QRH024K-680M QRV142F-1182 QVZ3230-053 QRG026J-103Z QRG026J-822Z QRG026J-821Z QRX019J-8R2 QRX019J-4R7 QRGO026J-680Z QRG019J-391 £RZ-CO5ZK471 €RZ-CO5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRGO26J-103Z QRG019J-183 QRV122F-470Z QVPS5A0B-023E QRV142F-2741 QRH124K-221M

Part Number QEN61HA-335Z QEES1CK-225B QEWS51JA-475 QEW52CA-107 QEWS52CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEWS2EA-106

Page 71

Coils Symbol L1502 L1503 11504

Transformers Symbol T1501 T1503,

Semiconductors Symbol 1C1501

X1101 X1102 X1103 X1104 X1105 X1106 X1301 X1302 X1303 X1304 X1305 X1401 X1402 X1501 X1901 X1902

01101 D1102 D1103 D1301 D1401 01402

01503 D1504 D1505 D1506 D1507 01508 AxD1701 A\01901 A\D1902 A\D1903 AxD1904 A\D1905

Miscellaneous Symbol AF1901 AXF1902

Descripiion Part Number

Linarity Coil A39835 Width Coil C30380-A Heater Choke C30445-A

Description Part Number

Hor. Drive Transf. A46022-BM Side Pin Transf. C39050-A

IC HA11244

Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SC1685(R) Si. Transistor 2SA673(C) Si. Transistor 2SC1685(R) Si. Transistor 2SC1685(R) Si. Transistor 2SD478 Si. Transistor 28D478 Si. Transistor 28C2610BK Si. Transistor 2SC2688 (K.L.M.) Si. Transistor 2SC1890A (E.F.) Si. Diode WO6A Si. Diode WO6A Si. Diode WO6A Si. Diode 1$Z473H Si, Diode 18Z473H Zener Diode RD10F(C) Si. Diode HF-1 Si. Diode VOSE Zener Diode RD11E(B) Si. Diode ‘WO6A Si. Diode 1SS81 Si. Diode 1SZ473H AsZener Diode RD20EV2 ASi. Diode 1S1887A ASi. Diode 181887A ASi- Diode 181887A ASi. Diode 181887A AZener Diode RD6.8EV3

AFuse 1.254 QMF53U1-1R25S AXUL Fuse 3A QMF66U1-3RO0S

Page 72

se satey 9t XIO1 XIO3 ond X18 VIDEO AMF. 25C454C oy 25¢1688 X102,x104 end X108 VIOEO_AME 2SA673C

i Tlosxd3 FG-B VioeO OUTPUT deczeil or 38ci8"

t

L

= SU-30I6A (ORT SOCKET pee sssr ||

503 BEAM LIMITER 2SA673 Tigo guannins ies :

| aod ‘Be bo tn,

t

  • ao tel a

sass SU-1103A MAIN PCB ASSY |

Schematic Notes Unless otherwise specified Resistance: (Q) (K-*KQ, M-MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher—> (pF), less than 1» (yF) working voltage -~ 50 (V) ceramic capacitor Inductance: (v H) Electrolytic Cap: Capacitance Value (y F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. vor DEFLECTION YOKE

= Fo nom nou 1701 YoRAY PROTECTOR SBsOP WE ascesrw Soe = CL B5ea3se ar 2868 S8caei or ESCzCRR 280809 ACI2OV 6OH2/S0Hz 2 indicates test point connection #10% oh indicates chassis ground unless otherwise specified Hz indicates cycles per second For safety purposes (and continuing reliability) a replace all components marked with safety symbol with identical type.

NOTE: FR — fusible resistor \—ex3—

G07-FBO Parts identification on circuit boards: 00-4147-03 e.g. SU1126A (R107 = R1107) $U3030A (R113 = R3113)

Page 73

REPLACEMENT PARTS LIST - ELECTROHOME 13”’’ MONITOR

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics important to safety.

DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CRCarbon ResistorC Cap.
Comp. RComposition ResistorM Cap
OMR: Oxide Metal Film ResistorE Cap.
VR: Variable ResistorBP E Cap.

MFR Metal Film Resistor

CMF RCoating Metal Film ResistorMM Cap.
UNF RNonflammable ResistorPP Cap.
FR: Fusible ResistorMPP Cap.

PS Cap Tan. Cap. Ceramic Capacitor Mylar Capacitor Electrolytic Capacitor Bi-Polar (or Non-Polar) Electrolytic Capacitor Metalized Mylar Capacitor Polypropylene Capacitor Metalized PP Capacitor Polystyrol Capacitor Tantal Capacitor

NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identical specifications.

Symbol

Outside of the P.C.B. Ass’y Symbol 4vo1 AspY01

AR AROS Aco4 x01 1c01 Lo1

BR BR sc WA

CH Description Main P.C.B. Ass'y CRT Socket P.C.B. Ass’y

Description APicture Tube A\Deflection Yoke PC Magnet Wedge A\Flyback Transf. AfFocus V R UNF Resistor 2202, 25W. K AC Capacitor 150 pF, AC1.5KV Si. Transistor IC Regulator Degausing Coil Degausing Coil Pin Terminal (2) Degausing Coil Pin Terminal Housing Groundstrap Assy. Groundstrap Wire Terminal Groundstrap Spring (2) Support Bracket RH Support Bracket LH SCREW 10-% Pix Tube Mtg. (4) Pyramidal Lockwasher (4) Clip P.C.B. Support (2) . Ground Lug Chassis Base Part Number

SU-1103A SU-3016A

Part Number

370ESB22(E) C29123-V A76366-A 30006 A19183-A A46606-A QRF258K-221 QCZ0101-005 2SD869 STR383 21-1007-31 34-708-01 34-709-01 34-697-04 34-228-03 35-3560-01 35-3919-01 35-3919-02 31-631018-08 33-255-01 33-629-02 34-33-04 38-452-01 Main P.C.B. Ass'y (SU-1103A) Parts List

Resistors Symbol R1406 R1408 R1410 R1414 R1415 R1421 R1422 A\FR1401 A\R1503 R1504 R1509 R1511 R1514 R1515 R1522 R1523 R1528 R1534 VR1501 AsR1703 ASR1704 AxR1901 R1902 R1903 R1904 AXFR1901

Capacitors Symbol 1402 C1411 C1412 C1508 C1511 AC1512 AC1513 Axc1514 C1515 C1520 C1524 C1904 C1905 A\C1907

Colls Symbol L1501 11502 L1503 L1504 11901

Transtormers Symbol 71501 T1503 Descripti Vv R Vv R CMF R OM R OM R OM R v R AF OR ACMF R Vv R OM R OM R OM R CMF R CMF R OM R OM R ZN R ZN R A\CMF R AXCMF R APosistor UNF R CMF R OM R AF OR jon 2002 2002 6.8Q1W J 3.3KQ 1W J 2.7KQ1W J 12KQ2W J 10KQ. 6822W K 11.8KQYUW +1% 5KQ 10KQ2W J 5.6KQ2W J 6802 2W J 8.2Q1W J 4.7Q1W J 56.Q2W J 39021W J

39K QW +1% 7.68KQUW +H1%

2Q7W K 5.623W J 10KQ2W J 2202%W K

Description Tan. Cap. E Cap. E Cap. PP Cap. E Cap. A\PP Cap. APP Cap. AXPP Cap. PP Cap. BPE Cap. M_ Cap. 2.2uF 16V K 100uF 160V A 3.3uF 160V A 5600pF 50V J 47uF 160V A 2000pF DC1500V J 2000pF DC1500V J 2500pF DC1500V J 0.53uF DC1200V K 1uF 50V A 0.1uF 200V K E Cap. E Cap. A\MM Cap. 10uF 250V A 0.1uF AC150V Z

Description Peaking Coil Liniarty Coil Width Coil Heater Choke Line Filter

Description Hor. Drive Transf. Side Pin Transf.

8-20 Part Number QVZ3230-022 QVZ3230-022 QRX019J-6R8 QRGO19J-332 QRG019J-272 QRG029J-123 QVZ3224-014H QRH024K-680M QRV142F-1182 QVZ3230-053 QRG029J-103 QRG029J-562 QRGO029J-681 QRX019J-8R2 QRX019J-4R7 ORG029J-560 ORG019J-391 ERZ-C05ZK471 ERZ-CO5DK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-5R6 QRG026J-103Z QRH124K-221M

Part Number

QEES1CK-225B QEWS52CA-107 QEW52CA-335 QFP31HJ-562 QEW52CA-476S QFZ0082-202 QFZ0082-202 QFZ0082-252 QFZ0067-534 QEN61HA-105Z QFM72DK-682M QEY0034-001 QEWS2EA-106 QFZ9008-104

Part Number A75360-6 A39934 C30380-A C30333-A A39475-J

Part Number A46022-BM C39050-A.

Page 74

Semiconductors Symbol 1C1501

x1101 x1102 x1103 x1104 X1105 X1106 x1301 x1302 1303 x1304 X1305 x1401 x1402 x1501 x1701 01101 D1102 D1103 01301 D1401 D1402 01503 D1504 D1505 D1506 D1507 01508 401701 A\D1901 401902 £\D1903 A\D1904

Miscellaneous Symbol A\F1901 A\F1902 Description Le.

Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Si. Transistor Transistor Transistor |. Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Transistor Diode Diode Diode Diode Diode Zener Diode Si. Si. |. Diode |. Diode Zener Diode Si. Si. Si. |. Diode |. Diode . Diode AXZener Diode ASi ASi ASI ASI. . Diode |. Diode . Diode |. Diode

Description A\Fuse 1A AXUL Fuse 3A

8-21 Part Number HA11244

2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2SA673(C) 2SC1685(R) 2SC1685(R) 2sD478 2SD478 2SC2610BK 2SC1685(P-S) Wo6A WO6A WO6A 182473H 182473H RD10F(C) HF-1 VooE RD11E(B) WO6A 18881 182473H RD20EV2 181887A 1$1887A 181887A 1$1887A

Part Number QMF53U1-1ROS QMF66U1-3R0S

Page 75

CRT Socket P.C.B. Ass’y (SU-3016A) Parts List

Resistors Symbol! Description

R3105vR 2002
R3106vR 2002
R3113vR §KQ
R3114vR 5KQ
R3115vR §KQ

R3116 OM R 10KQ2W J R3117 OM R 10KQ2W J R3118 OM R 10KQ2W J R3119 Comp. R 3.3KQ2”%W K R3120 Comp. R 3.3KQ2%W K R3121 Comp. R 3.3KQ2%W K

Capacitors

Symbol Description

C3107 E Cap. 10uF 250V A C3108 C Cap. 1000pF 0C1400V P

Colls

Symboi Description

13101 Peaking coil

Semiconductors

X3101 Si, Transistor X3102 Si. Transistor X3103 Si. Transistor

Miscellaneous

A ASCRT Socket

8-22 Part Number QVZ3234-022 QVZ3234-022 QVZ3234-053 QVZ3234-053 QVZ3234-053 QRG029J-103 QRG029J-103 QRG029J-103 QRZ0039-332 QRZ0039-332 QRZ0039-332

Part Number QEWS52EA-106 QCZ9001-102M

Part Number QQL043K-101

Part Number 2802611 2802611 2802611

Part Number A75522

Page 76

IX Schematics and Wiring Diagrams |

Page 77

a 1 Stata et

Sa a 7 Sea) meres

‘SUPER CPU 80

-Dowwo maw Jnes1~00308-4005

Baby / wioway

own wereR

Page 78

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 79

DESIGNATION LIST

DESIGNATION DESCRIPTION

ci,c2 4? mf 25y rdtant C3,c4 22enf bv tt C5,cé 470mf 6v ax.elect C7-C1O mf 50v ax.cr CPI 220mf 25v ax elect. CP2,cP3 mf SOv ax.er

RIR2 2.7KN V4aw 5% CRBN, R3R4 an R5-R8 1M Vew'

U1,u2 MB3730

Jl a4 STRT. KKIS6 J2 Zo " " 26 4 "

HSAl,2 HEATSINK ASSY. MH1-MH4 HEYCO BUSHING "

DIM. TOLERANCES UNLESS OTHERWISE SPEC CONCENTRICITY TR. 002 FRACTIONAL +1164 DECIMAL + 005 HOLE DIA + 002—.000 ANGLE 212° DO NOT SCALE DWG THIS DWG IS

Cima CONFIDENTIAL & PROPERTY OF MIDWAY MFG. CO. CROSS REFERENCE LIST DESCRIPTION QTY DESIGNATION PART NO

mf 50vaxce6CLIO0986-008002100

CP2CP3

47 mf 25vrdtant 2CIC20986-008003100
2amf bv2c3c40986-00800-1600
220mF 25vaxSiec, 1cPI0986-00800-3200
470mf 6v *2csce0986-00800-1700
INV 2w 5%4RS-RB0062-026D3-1Xxx
27201/4w2R3R40062-06883 -1XXx
27K °2.RLR20062-199 B3-1XXX
MB37302U1U2O066 -188Xx x - XX4x
2PINSTRTKKIS6 1J23000 - 16367 - 0200
Buoh2Shue3000-16367 -0300
Quyvl3000-16367 -0400
HEATSINK ASSY2HSAIL,

HSA2

HEYCO BUSHING 4 MHI-MH4

PC BOARD | A986 - 00010-£000

0017-00042-0014

A080 - 90910-E000

MIDWAY MFG. CO. FRANKLIN PK., IL. 60131 ABALLYCO REVISIONS DUAL PWR. AMP. ASSY frxarxo AQ80-90910-E000 |MOS5!1-00986- E010

Page 80

DESIGNATION

clot cioz C103 clos c1oe-c110 cur cua Elis eile, ci23- 136 C200 © 201,¢202 £203

cP crecer cre cP9-cel cris ceie-crzo creat cpe2-cP28 p29 ‘¢P30- cPa7 crx8 CP39-CP50 Pst cpse-crs7 cPse cess-crea ores. cree.

RIOz Ri04 RLOS R108 Rio? Ri08 R108 Ri cir RIG RN7.R UE aie Rizo Riz Rize Rize Ries RI26, R127, Rize RIe9 Riso RSI Riss, RISA Riss, Rise. RIS? RIB iO, R141 DESCRIPTION.

S3PF AX.CER. O-IUR AX. CER. OLIUF MYLAR ‘SOOPF AX.CER. a7 PF AX.CER 220 FF-AX-cER 350 PF AX. CER 820 PF AK CER 390 PF AX CER 190 PE AX.CER 470 PF-AXCER,

a7our !ev ELECT.AX O.O1UF SOV AX.CER. [oUF 25V ax. TANT, O-O1UF SOV AK. CER. 47OUF I6v ELECT. AX (.O1UF BOV AK. CER. tour o.01uF tour our tour o.o1ur louF ‘o.1uF S70UF I6V ELECT.AX. o.o1uF a70uF OUUF SOV AX CER

4.7% O#M /4W CRN, 1K OWM " L2kOuM 220004 22 onm 1k onM 3300Km 1 on 3300HM 4.7KOHM" : 1kOHM S600HM * tocoKm © ez008 A700HM " 5 Si0oHM . ik OHM * : 2kowm : toowm : 4700HM tk OM SioonM

To OHM 47008M sivoHM tk onM 2k OHM loon DESIGNATION

R201 R20F 203-4207, Roe,R209

RM AM2,RMS Ma

oro!

‘102 2103-0108,

a a2 a 9,810 an an

ce

C10 cu.cl2

Ft Fe F3 Fars Fe F7 Fe,Fo rio

98,010 ou oie

f97-Fa32

lesaiz vesaiza lesez iesas 1eses leseiz 1e802,03,04, D607

loses lesFe IesFio

iesou lesolz iesci2a

ota

a28

53,04.25,46,07

awi-owio

swi

xTaL

26: 082

43, 54.45,06,07

8080-80010. F000 DESCRIPTION.

IKOKM OOM tk OM * : arKone

4.7K SPIN SLE 47K iC PNSLE. 4.7K PIN SL.

inseir ae

2naaos 2uaies wPsA70

Taste! ats3e7 745248 yas74 7as04 wT

ravszee cmos Raw wx3enz O

748183 74832 74804 7aLs74 rais32 van-r

ras08 ras74 7as04 ausz0

EPROW EPROM EPROM EPROM EPROM EPROM TaLsoe av ai87

NVR CONTROLLER 7ais32 TALSISB rauses 7aLsa? TaLeo+

4083 4017 TaLs24s raisers sue ratsi7a rausis7 3419

Tausiss 7ats273 EPROM EPROM 7suse73 7a sis ratsi TaLsi74 TaLsi87 custom 1c V-T GEN

FERRITE BEAD

8pm Ic SockET ieein 24PIN" apn 4orin” 20PIN* zen”

200 : 2apin" 2erin™

TePn” .

KKISG AT. ANOLE OPIN KRISS. “1asin KKI00 RT: ANGLE 2 PIN KK 100” * SPIN R100" 2aPN ‘ZERO OHM RESISTORS

SWITCH PC MOUNTING

19,969 WHZ CRYSTAL

bus BAR

FLEX-PAC JUMPER:

SUPER CPU BOARD DESCRIPTION.

$3 PF AXCER. 7 PF ax cer OFF AX CER 390 PF AXCER 470 PF Ax.ceR 26 PF AK.CER

‘.01VF BOVAK.CER

wt {COV MYLAR SAME SOV AX, CER. ioWF 28VAx. TANT. 47008 16V AX ELECT

oon 70N

22 01m" rook 220 ows" 3300HM" 470 0908" sioonm= 560 0M” e200%m" ie om

Lak onm! 4.7K OHM

4.7K Orns 47K WPINSLP

insei7 4148

2naacs 2Naies Mesaro

74808 TaLsca 74Us08 740820 7aus27 7aLs32 rasta 7aLs7s ratsee TaLsiz TaUsise 7aLsi83 74usi57

ag a

a ag ae 382 saiTY mioway mes. co ALL RIGHTS RESERVED

PAT. PENDING a &

a

“

E TA ay 2 tal — - B { en

aH

= = ES

  • QESIGNATION. fl C191 e E185 - e110

e203 ry 6104,18,06,128-186,201,202 i C208 5 Citl-cure,c200

  • ‘cP2-cP7, cFo-cPia,cPI6-cP20, Greece ee. crscrcesr, P85: cbse ceeecra, cpsg-cees ' e108 2 cloz,cres . Pe,cP2i,cP29,cP38

“ ‘PL.CPIB,cPS8,CPOS

  • RI2G\RIZT,IS3,RI4, R40, R18 ‘ R108 ' R119 3105 2108, RN) RIB, RIZB,RI3S, RIZS. RIBOSE RUT,RIG,REOZ R120 R1Q2,R107,R109,806, Ried inize RSARO, R208-R207

H R104 3 8125, R131, R138 « ici Ri2,R208,8209

2 RM, AM 2 Ruz J RMS,

1 10 ' D102

' 101 ‘ gioz 6 103-108

Ail, 88,C10 08,e9 ce chee es 28, 011,64,25 49, 410 b10,09, £7.67

ee Gi,c6 010, 0n.012,F8,

ord “roa |

em se g ee ma fe i Ee i | fs oo = ep f oo

= i Fal

= Er

oo LU.

i

& :

surce PART NOS. 0986 -00800-0300 (0986 -00890- 2600 (0806 - 00800- 1000 (0986-00800 - 3000 ‘9986-co800- 3802 (0986-00800- 350! (0988-00800-2200

0986-00800-0100 (2988-00800- 9200, (0986-00800-3400

(0986-00800-3300

(0062-08185-109 (on82- 06385-1Kxx (0062 1083-14xx. (0062- 155B5-1XxX. (0062-14488-IKXX 0082- 082-15 0062-162: 0082-17481 (0062-17883-1XxX

(0062- 18305-1xxx (0062 - 19383-1xxx (0062- 21108- XxX

0986-00804-2400 (0086- 00804-4600

(0966- 00801-0800 0986- o0801-o100

‘2986- 00802-0200 ‘9986- 00802-0100 ¥986- 00802-0300 (0988- 00803-0400 (0888- 90808-1007 (0986- 00803-1000 ‘0886-008021004 (0986- 00603-9800 ‘0986- 00803-0800 (9388-00803-1800, (0986-00803-1008 (0988-00803-9000 (0986—00803-100e (0986—-00803-1900, (0986-00803-1000 ‘0886-00803-9700 ZERO OWM RESISTORS 19

SWITCH Pc MOUNTING ' 19, 960Mn CRYSTAL ' bus eAR 2

FLeXpac 5 33,04,05,08,07

DESCRIPTIONa(DESIGNATION.PARTNOS_
7auate!1alc986--20803+
TALSITS2F7,08on
TauszHiose
prevenzisles
74Ls2734F4,F5,62,689986-00803-1001
Tate‘aSoee-ooee3-2200
esse'&ons -o9803~7900
wssee'3:oaee-co80s- 7700
aoeHrepeeose0s-e700
rd;Seee-o0003-2000
os nawHaGoes~ 0803
ome‘fsSeae-oosos-ro08
934191Flo
H-T GEN.1ala
va en'oedee coscs_s008
vee!aeObes 09803-8100
wise custom:onooue 09808-9200,
ie cuneren;&Gase-ooe04 3209
EPROM1a
‘EPROM1te
crow:baROMERO0308 ~ 00808-0001
cenowtHbe
ernow'or
EPROM'es}

ernow '

arin ic socxer2\esara,tesoie2086-00804-3600
ermns2lesaiza.tesoizacave coe0s-3709
poms:reset, icses,oete-coeos-3000

‘ese

pers2tesea,icsrec296-00804-3400
ioeoIsseariceoe,oeee-ooeos-3000,

tespsusoa, 1eSberteSbe, 108 ears iegeaiesoa

sors'reset-00804-8500
FERRITE BEADS2Fa7- 532"00804000
100 RT-ANGLE 2PIN CORN.1vanc086-—00804~-4200
Kilov nTaNeLe ermeomre9804 4200
Raise nranocesrincow,stacota 4400
KRIge RT. ANGLE cPINCOMNS|ue2ee—cosos—as00

RKioo aT ANGLESAPmCoMN. 8 ‘0386 —00804-4700

wi-vwi9 086-00804~4000

sut 0986--00804-3100

xTAL 9886-00804-4900

BI, 882 0986-00804-4100

J8,44,98,0697 0986-00804 -4800

‘A.GOSH [exo on DOMINO MAN

Fut poms 1 PER T Baty‘ MIDWAY MFG.CO.

SUPER CPU BOARD ASSY DWG 4.082 - 900:0- F000 MoS! - 00303 - A0O7 |

9-4

Page 81

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 82

QESIGNATION DESCRIPTION

12 100 wt ax. Lect 101 100 PAX. CER.

cP I-3, 5-10 cPi2-20,22-27, cP29-33, 35,36, CP38-41, 43-47, .01 1 AX. CER. cP49-54,56-61, P63-67,69-71

cP 4, 11,21,28,34, cP 37,42, 48,55, Opt 25 AX. TANT cP 62,68,

RIOI- 119,201,202, | K 1/4W 5%

PMi,2 @PIN 1K SIP RM 3 1OPIN IK SIP

cas EPROM ae 74.Si57 Ica 74Usisr cas 74.8157 cas 7acsis7 cas 74 .sis7 ica? 74. sis7

cas EPROM Be T4a.sioa cas Tasisa ca racs3 18s 422 Io 86 azz 187 74532

lect EPROM ec? Ta. sisa Ie cs 74. S194 cs 74832 les 422 ce 422 ie er TALS 32 DESIGNATION List

DESIGNATION DESCRIPTION

ie ot EPROM 1c 02 TaLsio4 108 7418194 104 74.8273 1c DS 74.8157 1c 06 74.187 1c 07 TaUS273

ee 74acsi9a rear) 74.S194 Ice 4 74.5374 es T4USIST 1c eS Ta SIST

cre 7400 ier 3 74804 icra TALS 374 Io FS 74.8157 Ic F 6 74.8187

ra 74Ls 86 ic 62 74L820 163 7a.s 283 1c 64 74S 283 1 65 74.5283 1c 66 74.8157

om 74. s86 Ion? Taira IONS ras74 ICH a airs Ions rai74 Ione TAUSIST

weve 74.530 Ie v3 7430 ya 7a.s273 58 422 6 T4.SiS7

eK 74161 exe 7430 eK 3 7474 cK a 7416! IoKs 422 Ic K6 24-2 DESIGNATION DESCRIPTION.

ie ut 741820 ee 7408 leus 7474 Ie 74.szes ous 422 ies aia-2 leu? 74.8157

com 7430 Ie m2 7432 cM 3 ras74 oma rare! lous azz loom? 74.8157

oN 7430 Io N2 7427 IONS 74Us273 Ion 74.5283 IONS 74Ls 245, IC NG 7404 Io NT 74.8187

1CS.A1,B1,C1,01, 28PIN IC SOCKET

1CS85,6,C5,6, 22FIN IC SOCKET J5.K5,C5,MB,

1CSK6,L6. IBPIN IC SOCKET 93,4,5 24 PIN SOCKET Jwi-vwe. JUMPER WIRE BBI,2 Buss BAR

POMHI- 4 PC BO SPACER PoMHS-8 PC MTG SCREW

A080-81399-HOOO VID.GEN. PC

VIDEO GENERATOR F.C. ASSY DWG A082 - 91399- HOOO. MoS! - 00303

  • Aoos
[1[jarty
:es |eT760

ele rs

eeoO.eo.awoIon
2(===CcFF2

hg ae

cfe=
-sie2
ccr2
cCx;
=ialeyee,
23c[ene=tie&1
2 33Sa--*"i
2 FCfe_
|3 283%‘cc,
|5 dene owon *Pag:
2 2326 4oeH
af2
EpcCC2
Aon)etatT,Fae of8
SrCcct
sh omor aoewa eras5

f 1

° ®

: ‘

: 2

fePra
Ccj
esoe apeeeeee6
-S2
iCC(1
aeas3
1.mewsiens:
prea we A. GOSH[ato DOMINO NAN7
romance~=Baty | MIDWAY MFG.CO.Py
FULL [po meee ONE PERPaani‘

DESCRIPTI 100 P150V AX. CER Ol pt SOV AX. CER.

1Owt 25v ax. TANT

100 wt 25 ax. €LEcT,

1K 174 CRON, FLM \k 8 PIN SIP 1K 10 PIN SIP 2ua-2 7400 7404 74804 7408 rais20 ra27 7430 74.830 7432 7aLs32 7474 ras74 7ase6 74LSI57

74161 raire 74178 racsiga raiseas, 7acs273 74.283 7acs3re 93422

EPROM EPROM EPROM EPROM JUMPER WIRE BUSS BAR Pc. BOARD

24 PIN SOCKET 28 PIN SOCKET 22 PIN SOCKET 18 PIN SOCKET

Pc 80 SPACER Pc MTG SCREW CROSS REFERENCE LIST

DESIGNATION CPI-3, CPS-10, cPi2-20,cP22-27, cP29-33,cP35, 36, cp3e-41,cP43-47, cP49-54,cP 56-61, cP63-67,CP69- 71 cP4,11,21,28,34,37, cP42,48,55,62,68. ce

RIOI~119, 201, 202 RMI, 2 RMS, K6,L6 F2 Ne FS

G2,ur ne J3.K2, MINE v2 M2 847,047, K3,U3 3, M3, GME A2,3,4,5,6,7, 05.6, €5,6,F5,6,66,H6, J6\U7M7.NT, ka Ma 2,5 Ma 82,3,C2,3,02,3,2,3 NS 04,7, 04,N3 63.4.5 L4,N4, cara 85,6,C5,6, 9 5,K5,L5,m5 At (VGA) 8: cr oF (v6.8) (vec) (v6 07 awi-8 e812

5345 Iesa,81,C1,01 ICS B5,6, C5,6,05,K5,L5,M5 Ics K6 Le

PCMH! -poMHa PCMHS-PCMHE PART NO. (0986-00800-1000 0986- 00800-2500

(0986 -00800-2400

0986 -00800-1800 0062 17983-1xxx 0986-00804 -1100 0986-00804 -1000 0986 -00803-2300 0986-00803-2800 0986-00803 -8300 0986 -00803- 3100 0986 00803-3200 0986-00803 - 3400, 0986 -00803-3500 0986 -00803-3600 0986-00803-4300 0986-00803-4400 0986 -00803- 3700 0986 00803 -4500 0986 -00803-4100 0986 -00803-4200 0986 -00803-2400

(0986-00803- 2500 0986 -00803-2600 0986 00803-2700 0986-00803-2900 0986-00803 -3000 (0986 -00803-3800, 0986-00803- 3900 0986 -00803-4000 0986 -00804-0800

ROM/EPROM OPTIONS KIT (0303 -00803 -0003

0986 -00808-0200 0986-00804-0900 A080 -91399-£000

0986-00804. 4700 0986-00804-0300 0986 -00804-0700 (0986 -00804-0600 eas oor, ox 0017- 00101-033

Page 83

9-7

Page 84

DESIGNATION LIST DESIGNATION. DESCRIPTION. DESIGNATION.

woes

Tl ee J8e= 2 5

ta an} c

Page 85

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 86

& Zz. ae Fp

Page 87

DESIGNATION «

cror coz C103 cro4 C105 cro

Cros cro9 C110 ci C201

C203 c204

6208 c208

ces

Rio R102 Ria R105 R196 Rio?

R109 Rio Raitt aii RI13 Risa

Riis DESCRIPTION

4700u Ax ELECT 470u! AX. ELECT tut AX. CER tut AX. CER Tot AX. CER 4TOut AX. ELECT 10001 RD. TANT tot 80. TANT 4.7ut AD. TANT tut ax. CER. tut AX. CER Olu MYLAR O33uI MYLAR Out MYLAR O47ut MYLAR 82001 AX. CER Out AX. CER 0.082ut MYLAR

tut AX. CER

18.hm SW WIRES. SPACER 680mm 1/2W 5% 1Oonm SW WIRES. SPACER 27onm 1/4W 5% 2700nm 1/4W 5% 6.2K 1/4W 5%

1K 174W 5% 16onm 15W WIRE: 8.80nm 1/2W5% 680mm 1/2W 5% 12k 174W 5% 4Tohm 114W 5% 1600nm 1/4W 5% spacer DESIGNATION LIST

DESIGNATION

iar Rie R200 R202 R203 R206 R205 R206 R207 R208 R209 R210 Ronn R212 R213 Rove R218 R216 Fair R218 R219

vR101,102

D101 D102 0103

D105 D106

D204 D208

Q102 0108

ut

uz us

us

Lior

aor

Fo1as8

Fei

Tw

ry

a4

ter

Lae

Hsat

MrnSAy

wis

Fen 2 . DESCRIPTION

S600nm 1/4W 5% 1500hm 2W 2700nhm 1/4W 5% 1.2K 1/4 5% 11M 1/aw 5% 33M 1eW 5% TOM 1/4w 5% 100K 1/aW 5%

33K 1/4W 5% 2M 1/aW Sm 1M 14W 5%

12M 14W 5% 75K 1/4W 5% TSK 1/4w 5% 220K 1/4W 5%

3.9K 1/4W 5% 1.2K 114W 5% B2onm 1W 10%

270uhm 1/4W 5% NOK aw 8% 6B onm/ZW5%

1000hm POT

AIS

AISF ANSE ANSE ASF 1N4001 1Na14s Ina tas 1N4 148 1N4001 1N4001

2N2905 2N2905, 2Na401

Lous REG M305 REG M3900 sN28

22uM INDUCTOR

BATTERY 3 6¥DC BODEG C

2 8A $ BLO FUSE

Fuse CUP

FERRITE BCAD.

TE WRAP

SPIN PG MOUNT CONN (MALC) | 1SPIN PG MOUNT CONNAFEMALE) 1SPIN PC. MOUNT CONN (MALE) 3PIN PC MOUNT CONN (MALE)

FUSE TAG

SYSTEM TAG

HEAT SINK ASS'Y 1

MOUNTING HARD WARE(HEAT SK) 2 screw

4 WASHER, 2 HOXNUT

JUMPER WIRE

FERRITE BEAD MOUNTING HARD FROJ. ENGL. DEKKER CROSS REFFERENCE LIST

DESCRIPTION Oy 4791 AX. CER

e boro

e106

‘orn 820p! AX CER. 7 Otut AX. CER

Otut MYLAR Oaut MYLAR 047ut M¥LAR | 0.082uf AX. CER tut AX. CER

tut RAD. TANT 4.7ul RAD. TANT

100ur HAD. TANT 470u" AX ELECT 470€ st AX. ELECT

16ohm 15W 5% 1Bohm SW 5% €.80nm 1/2W 5% toonm SW 5% 27onm 1/4W S% 47onm 1/4W 5% 68onm 1/2W 5% B20nm 1W 10% 1500hm 2W 5% 1GOahm 174W 5% 270unm 1/4W 5% S6A0hm 1/4W 5% 1K 14W 5%

12k aw 5% 3.9K /4W 5% 62K /4W 5%

33k V4W 5% 75K 174W 5% 100k 174 5% NOK 174W 5% 220K 1/4W 5%

1M 1/4W 5% 1AM 174W 9% 12M 1/4W 5% 2h 1/4 5% 99M /4W 5% WAW 5%

1090hm POT 2

  • _ [sams wolow | MIDWAY MFG, CO. FULL vcoo | PER. a ASSEMBLY DRAWING I25VA PWRSPY|

A082-90412-D000 MOS!-00945-D006 LM305 REG. 2 555 t

M3900 1 4n26 1

ANSE RECTIFIER °

1waoor 3 wNatas 3

2N2905, 2 anaaot 1

BATTERY 3.6VDC 600EG-C FUSE 3/84 S-BLO FUSE CLIP Tle WRAP.

FERRITE BEAD FERRITE MOUNTING HOW. 2

22u4 INDUCTOR :

FUSE TAG. ' SYSTEM TAG 1 pce 1

HEAT SINK ASS'Y : (SEE WS ASS'Y DRAWING "xx NOTE") { 4-40%10 SLT RND. 2 We} 4-40 HEX NUT 2 WSH 4-120-.250-018 4

PIN P.C, MOUNT CONN. (MALE) 9PIN P.C. MOUNT CONN(MALE) 15PIN PC. MOUNT CONN (FEMALE) 1SPIN PC. MOUNT CONN. (MALE)

22 AMG TOR BARE 2.5" 5 DESIGNATION +

e108

206,208 201,203 G202 c204 c207 6103,104,1°¢,111 Pi crc C109,

€ 102,106 c1ot

R110

Riot

Rit

R104

R105 aia 102,112,219 R216 Rie

R115 106,201,217 Ruir

R109 113,202,215 R18 R107 R207 211,212 R206 R218 R219 R209 R203, R210 R208 R208 R205

vai01.102

vie vs us ua

D101 +95,

106,204,205, 0201-203

0102,105

B10" e Forse Tw

Fen2

Femnt.2

L101

SAY

MH HSA 1A,24 MHHSAIE, 2€. MH HSA 18,10 MH HSAZB,20,

a8

aa a8

ows PART +

0945-00811-0100 0945-00816 0400

0945-006 16-0100 6945-00516-0200 0945 00816-0500 0945 -G08 16-0300 (0945-0081 6-1900 (0945 00811-0200

091,-00811-0300 9945-00811-0400 0445-00811-0500 0945-00816-0600 0945-0081 1-0700

0945-00815-0100, 0945-008 15-0200 0062-04703- 1xxx 0945-00812-0100 0062-06883-1xxx 0062-08603- 1xxx 0062-09803. 1xxx 0062-104F5 1xxx 0945-00812-0200 0062-12483: 1xxx 0062-13863: 1x 0062- 16283-1%xx 0062-17982- 1XXx 0062: 18383- 1xxx (0062-20783-1xx (0062-21 7B3-1Xxx 0062-25183: 1Xxx 0062 26983 1xxx 0062-27583 1xxx (0062-27783- Xxx 0062-29183 1Xxx (0062: 32383 1Xxx 0062 32583 1Xxx (0067-32 783- 1Xxx 0062-33783. 1x7 0062-34783: 1XXx (0062-37 183- 1Xxx

0945-0081 4-090

(0945-00813-0100 0229-00810- 4500

0945-008 13-0200 0945-00813-0300

0945-00804-0200

0945-00804-0300 0945-00804-0500

(0945-00808-0300 (0945-00804-0400

0017-00003-0377 0945-00808-0400 0017-00003-0214 0945-008"4-0300,

0017-o0vos-o225 0017-00033 0139,

0945-008 14-0200 M95 1-00945-A004 Ma5 1-00945-A009 ‘4080-90412-L000

4945-00008-0000

0017 - 00101-00727 0017-00103- 0002 0017-00104-0071

0017-00021-0443 0017-00021-0425 0017-00021-0441 0017-00021-0440

0151 -00087-0000

9-11

Page 88

' aio! Fe ms j ent77@ FERRITEBEAD 0.10 +12v/ save anit vooie oRO 1 AG88-00002-0000 T = LZ € — WIT — “JE-1I VIDEO DRIVERS oy | | SS wise fou ofr BP vew ' nt 4 i} —t an! \ | | MT 89 DOMESTIC ' ane vt ' S | i | MT90 EXPORT 1- =~ 5 o it y a | in i : wiles | 1! : x i || fl rio ia) ' ,__J | | ' 1502 ba 902 d neg R107 ! 8.2K + | ssooomr| |! __} e102 esau ae) a70ur ' i aioe b ' eo || | res 5.6. -SeNseCi2v) ' wriigo i ' i ; = yo-g ——__ \\ gfe ' i lesa L | vate ' i ' | | | | | a JA=T LOGIC @RO | ut i | } ' : ix | i i 88 4__SENSE ~

i : rn a Uior 0.22uK Azle pgs ineou veel veart ! 1 i} iti on POPE 9 ley pe T i : it ; I ca0s Toss | noir _ mal a ' i} e2orF tN4001 | 86V BA hy my ty er 001M ' my \ | Saved oak lee i 1 aa ia + = ev 5-1 _ COUNTER DRIVERS | aes t nara Fears beno ne ¥5V/ 7SAMP _J4-3 Lo016 oxo j ' a ae T J4=6 Losic eRD | ' ny sw \ ‘34-5 LODIC BRD. | : My as 45-2 AUK, BRD iH 1 uy 12K H im 1 i ut he it ooo ny J nt Mt * Mt Rw 7 7 + nt + 1 cio? vayoa se 108 = nm eonr 100" 7 470me ht | | L 44 14.9 Losic ek | tf = HN | deur | ' 560 34-10" LoBIc @RD ' J5=5 AUK, BRO | “CONTROLS | pais * 7 JS-7 CONTROLS | | ss + 34-2 -SENSE (3¥) EARTH GND

I H ! 3. UNREG. AUX. V 5-14 CONTR. LAMPS: ' 1 owe 105 ‘roi. Pibeiitie Vasil ; i Gf UNREG FILTERED V 8-18 avoiocer. WITH APPLICATION = : via vies 1 1 wie so vew 4 | cio _—| 101-0105 wes Bian po yo JS-L_ CONTR. LAMPS FROM X-Y MONITOR _XFMR ' fl D103 [cose foe harion eeu i 14 i 2168 TN, AUK. ‘8218 AUDIO cKT. ye-2 — = R204 R208, ; ‘ S34 iow i ‘ +5y + 1 boo ‘ : 0 1 va aepe Pon ae = = = Re SYNCHRONIZATION ~ | R201 48 PK ozo pgozReO8 : oe ' 270 [COME Ngiae iM 1h poy : 1 SBE ‘| ‘ sey eby ' 1 | peor ue a i 1 | ineies fo.0830F at 2 i <I sie ' ~ , a atiis Sorel —_oestac snc ‘| = it 3 : tf esas \ | = - PUMP CHARGER - -------- a! Tos cu L - n L $ ' C207 208, | \ oscar T come a = area + '

A082-90412-D000 i Ir i ; | : | ov

: het | : ns | : oN avs 200! ~ | 1 : — oe mt son ; 108 ppoutor ene: oeenen MIDWAY MFG. C0,

9-12 i ' 1 = = PoveRr Surokr ve F yes|-00045-Do07

  • 777 "ONE SHOT ~~